Defining integrals over volume element in curved spacetime together with the mass and energy densities within that region of spacetime is apparently equivalent to the given energy and mass of that body or particle. With this in mind equations involving energies and mass can be rewritten in terms of their densities and the integral over the volume element. The idea find its place in the Hamiltonian formulations, and can be carried over into quantum mechanical frameworks systematically accounting for the effect of spacetime volume structures and gravity on dynamics of quantum systems. This article briefly explores this concept and runs through various frameworks and equations relevant to this idea, particularly the schrodinger-Newton equation and discusses the cosmological constant as a vacuum energy density.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering

Temporal changes of population densities and species richness of three main pollinator groups: moths and butterflies (Lepidoptera), bees, wasps and sawflies (Hymenoptera) and hoverflies, horse-flies, tachninids and bee flies (Diptera) were investigated in the Carpathian Basin. Maintaining pollinator divesrity is a crucial factor for preserving our biodiversity and ecosystems, furthermore several pollinator species has strong economic role in maintaning crop and fruit cultures. Our conclusions are based on our three or four decades of faunistic surveys in various regions of the Carpathian Basin. Analysing and comparing our data with the historical data of the last 50 years, we concluded, densities of some pollinators were declined during the past decade and the half (Symphyta, hoverflies), although populations of several species of Mediterranean-origin were grown (Aculeata) and even new species were migrated from the warmer regions. In numerous cases, this decrease was dramatic: more than 90% decrease of certain butterfly species were detected. On the other hand, the composition of pollinator fauna significantly changed due to the disappearance of some montaneous or mesophyle species. The main reason of decrease of pollinator communities is partly the climatic change and partly anthropogenic factors. Our conclusion: in our region, the pollinator crisis is present, but moderate; however, there is clear sign of the gradual transition of our pollinator fauna towards the Mediterranean type.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

Quantum nonlocality represents correlation properties between subsystems of a composite quantum system, usually including the four types: Bell nonlocality, steerability, entanglement, and quantum correlation (quantum discord). Given a basis $e_{AB}=\{|e_{ij}\>\}_{i\in[d_A],j\in[d_B]}$ for the Hilbert space $\H_A\otimes \H_B$ of a bipartite system $AB$, a density operator $\rho^{AB}$ (quantum state) of $AB$ can be represented as a $d_Ad_B\times d_Ad_B$ matrix $\hat{\rho}_{e_{AB}}=[\]$, called the density matrix of a density operator $\rho^{AB}$. A natural question is what is the relationship between the quantum nonlocality of a density operator $\rho^{AB}$ and its corresponding density matrix $\hat{\rho}_{e_{AB}}$? In this work, we discuss the relationships between quantum locality and basis, and prove that one type of quantum locality of density operators and that of their density matrices under a basis are the same if and only if the chosen basis is the tensor product of the bases of subsystems. Consequently, different bases define different quantum nonlocality density operators.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

We primarily investigate the existence of solutions for fractional neutral integro-differential equations subjected to Neumann-type boundary conditions, which is crucial for understanding natural phenomena. Taking into account factors such as neutral type, fractional-order integrals, and fractional-order derivatives, we employ probability density functions, Laplace transforms, and resolvent operators to formulate a well-defined concept of a mild solution for the specified equation. Following this, by integrating fixed point theorems, we establish the existence of mild solutions under more relaxed conditions.

Osteoporosis is considered a serious public health problem, particularly affecting the postmenopausal period. In 2018, in the Republic of Kazakhstan the total and primary incidence was 10 and 3.7 cases per 100,000 adults, respectively. The objective is to study osteoporosis prevalence and indicate main factors affecting low bone mineral density by screening adult population of Abay region, Kazakhstan. The target group were 641 respondents aged between 18 and 65 years old, Kazakh population living in Abay region since birth. All participants filled out questionnaire and had a bone mineral density measurement by dual energy X-ray absorptiometry (DXA) between July 15, 2023 and February 29, 2024. Logistic regression analysis was conducted to assess the association between low bone mineral density and key demographic characteristics, aforementioned lifestyle factors and nutrition habits. We identified the prevalence of low bone density and osteoporosis at the level of 34.1% with the highest prevalence in the older population group (50+ years) - 48.3%. Regression analysis revealed a number of indicators associated with the likelihood of bone sparing. However, only 4 of these showed significance in the final multivariate model (R2=22.4%). These included age (AOR 1.05), body mass index (AOR 0.92), fracture history (AOR 1.64), consumption of nuts and dried fruits were associated with lower prevalence of osteoporosis (AOR 0.48). Our study was the first in Kazakhstan that investigates the association of key demographic, behavior and anamnestic factors with low mineral density.

Climate change is increasing air temperatures and altering the precipitation and hydrological re-gime on a global scale. Challenges arise when assessing the impacts of climate change on the local scale for water resources management proposes, especially for low mountain headwater catch-ments that not only serve as important water towers for local communities, but also have distinct hydrological characteristics. Until now, no low flow or hydrological drought studies have been carried out on the Lauter River. This study is unique in that it compares the Lauter River, a transboundary Rhine tributary with a nearby station on the River Rhine just below its confluence at the French-German border. The Lauter catchment is a mostly natural, forested catchment, however, its water course has been influenced by past and present cultural activities. Climate change disturbances cascade through the hydrologic regime right down to the local scale. As we are expecting more low flow events, the decrease in water availability could cause conflicts be-tween different water user groups in the Lauter catchment. However, the choice of different methods for identifying low flow periods may cause confusion for local water resources manag-ers. Using flow rate time series of the Lauter River between 1956 and 2022 we compare for the first time three low flow identification methods: the variable threshold method (VT), the fixed threshold method (FT), and the Standardized Streamflow Index (SSI). Similar analyses are applied and compared to the adjacent Maxau station on the Rhine River for the same time period. This study aims at 1) interpreting the differences amongst the various low flow identification methods and 2) revealing the differences in low flow characteristics of the Lauter catchment compared to the Rhine River. It appears that the FT reacts faster to direct climate or anthropogenic impacts whereas VT is more sensitive to indirect factors such as decreasing subsurface flow which is typical for small headwater catchments, such as the Lauter where flow dynamics react faster to flow disturbances. Abnormally low flow during the early Spring in tributaries such as the Lauter can help predict low flow conditions of the Rhine River during the following half year and espe-cially for the summer. The results could facilitate Early Warning of hydrological droughts and drought management for water users in the Lauter catchment and further downstream along some of the Rhine.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

Amylose content (AC) stands as a pivotal determinant of rice grain quality, primarily governed by the Waxy gene (Wx), with its allelic diversity significantly influencing AC variation. In the current culinary landscape, soft rice varieties, known for their low AC and superior palatability, are particularly sought after by consumers. Notably, many soft japonica rice varieties cultivated in southern China, including the Nangeng series, are characterized by the presence of the Wxmp allele, derived from the ancestral Wxmq allele. While both alleles are associated with reduced AC, there remains a paucity of detailed understanding regarding the interplay between specific functional single nucleotide polymorphisms (SNPs) within these alleles and the overarching rice grain quality. Employing site-directed mutagenesis, we engineered three distinct transgenic rice lines, each harboring either the Wxmp, Wxmq, or Wxb-5c alleles, against the background of the glutinous rice cultivar Nip(wx). This suite of transgenic rice showcased a gradation ingrain transparency inversely correlated to AC, delineating a sequence from Wxmq, signifying the lowest, through Wxmp, to Wxb-5c, indicating the highest. Consequently, this gradation in AC precipitated variations in other rice grain physicochemical attributes, such as the taste value of cooked rice, gel consistency (GC), and starch pasting properties. Furthermore, analyses of gene expression and enzyme activity revealed that the functional SNPs, Ex4-53G/A and Ex5-53T/C, lead to a decline in the GBSSI enzyme activity without affecting expression levels. These findings underscore the potential of harnessing these SNPs in breeding programs aimed at developing soft rice varieties endowed with enhanced culinary qualities.

The results shown in this paper extend our research group's previous work, which presents the theoretically achievable hydrogen engine-out NOx (H2-NOx) Pareto front of a hydrogen hybrid electric vehicle (H2-HEV). While the Pareto front is calculated offline, which requires significant computing power and time, this work presents an online-capable algorithm to tackle the energy management of a H2-HEV with explicit consideration of the H2-NOx trade-off. Through the inclusion of realistic predictive data on the upcoming driving mission, a model predictive control algorithm (MPC) is utilized to effectively tackle the conflicting goal of achieving low hydrogen consumption while simultaneously minimizing the NOx. In a case study it is shown that the MPC is able to satisfy user-defined NOx limits over the course of various driving missions. Moreover, a comparison to the optimal Pareto front highlights the MPC's ability to achieve close-to-optimal fuel-performance for any desired cumulated NOx target on four realistic routes for passenger cars.

Rationale - From the year 1 anno Domini until 1855 with the third Plague, major pandemics occurred on average every 348 years. Since then, they have occurred on average every 33 years, with Coronavirus disease 2019 (COVID-19) now underway.Even though current technologies have greatly improved the way of life of human beings, COVID-19, with more than 700 000 000 cases and 6 950 000 deaths worldwide by the end of 2023, reminds us that much remains to be done. Objective - Given the frequency and duration of recent pandemics, it might be wise to start thinking about preventative methods to minimize the impact of future pandemics. This report looks back at 18 months of COVID-19, from March 2020 to August 2021, with the aim of highlighting potential solutions that could prove practical, or even essential, for the future. Material - COVID-19 data, including case and death reports, were extracted daily from the Worldometer platform to build a database for macroscopic analysis of the spread of the virus around the world. Demographic data were integrated into the COVID-19 database for a better understanding of the spatial spread of the SARS-CoV-2 virus in cities/municipalities. Method - Without loss of generality, we only analyzed data from the top 30 (out of 200 and above) countries ranked by total number of COVID-19 cases. Statistics (regression, t-test (p < 0.05), correlation, mean ± std, etc.) were carried out with Excel software. Spectral analysis, using Matlab software, was also used to try to better understand the temporal spread of COVID-19. Results - A good linear correlation was observed between the number of cases and the respective number of deaths depending on the country, i.e. y = 0.0121x + 19559 with R² = 0.8042. The analysis then focused mainly on the number of cases.This study showed that COVID-19 mainly affects G20 countries. The most interesting result is that cities/municipalities with high population density are a powerful activator of the spread of the virus. The current demographic context seems to be becoming a societal problem that must be addressed adequately.Spectral analysis highlighted that the very first months of spread of COVID-19 were the most notable with a strong expansion of the SARS-CoV-2 virus. On the other hand, the following six months showed a certain stability due mainly to multiple preventive measures such as confinement, closure of non-essential services, wearing of masks, distancing of 2 meters, etc. Discussion - Analysis of case and death data showed that COVID-19 mainly affects G20 countries. Nevertheless, the most interesting result of this study is that cities and municipal areas with population densities of several thousand inhabitants per square kilometer largely favored the spread of the SARS-CoV-2 virus. It is believed that such a demographic context is becoming a societal problem that developed countries around the world will sooner or later face and therefore needs to be adequately addressed. Conclusion - COVID-19 has made us understand that it is time to act both preventatively and curatively. Phenomenological insights suggest that the next pandemic could occur in less than 50 years. It may be time to launch new societal projects aimed at relieving congestion in densely populated regions.

Preterm infants have increased body adiposity at term equivalent age and risk for adverse metabolic outcomes. The aim of the study was to define how nutrient intake may impact body composition (BC) of very low birth weight infants fed with early progressive enteral feeding and standard fortification. Eighty-six infants with

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

China's economic development has shifted from high speed to high quality. This study constructs an evaluation index for China’s high-quality development utilizing a new development concept. The entropy method and cluster analysis were used to assess the level of high-quality development in China between 2015 and 2021. Kernel density estimation method was employed to explore spatiotemporal dynamics. The results reveal significant differences in the level of economic development among provinces in China; the eastern region is significantly better than the central, northeastern, and western regions. From the perspective of the sub-item evaluation, challenges with uneven, uncoordinated, and insufficient economic development exist in various Chinese provinces.

Abstract: Dispersal strategies of a species can affect its invasion success. Investigation into the dispersal strategies of invasive species in relation to different factors helps our understanding of the invasion mechanisms and provides knowledge for population management and invasion evaluation. Tetranychus ludeni Zacher (Acari: Tetranychidae) is an invasive species, which is native to Europe but now cosmopolitan. Here, we examined the effects of age and density on dispersal in mated females. Our results show that older females with more eggs were more likely to disperse and moved longer distances than younger ones with fewer eggs. Older females spread most of their eggs out of the natal habitats and over longer distances, which reduced competition and increased offspring fitness. Females significantly increased dispersal probability and distance with the increase of population density to avoid crowding. The synchronization of dispersal and reproduction, along with the positive density-dependent dispersal strategy, may facilitate habitat colonization and invasion speed of T. ludeni.

Tropical rock lobsters (Panulirus ornatus) are a highly cannibalistic species with intermoult animals predominantly attacking animals during ecdysis (moulting). Rapid, positive characterisation of pre-ecdysis lobsters may open a pathway to disrupt cannibalism. Ecdysial suture line development is considered for pre-ecdysis recognition with suture line definition compared for lobsters emerged and immerged, using white, near ultraviolet (365 nm), near infrared (850 nm) and spe-cialty Osram SFH 4737 broadband IR LEDs against a reference of intermoult lobsters with no suture line development. An alternative pre-ecdysis recognition strategy used a novel low-cost spectral camera composed of the Sony IMX219, AMS AS7265x spectral sensors and Osram SFH 4737 broadband infrared LEDs. Images and data using the novel low-cost spectral camera was acquired from intermoult, pre-ecdysis, and post-ecdysis lobsters. Compared with the white light appear-ance, suture line definition was enhanced under 850 nm, 365 nm, and SFH 4737 LEDs for immerged lobsters, while the 850 nm LED achieved the best suture line definition of emerged lobsters. The spectral camera was unable to characterise pre-ecdysis. A least squares regression for binary classification decision boundary successfully separated 86.7% of post-moult lobsters. Achieving post-moult characterisation validated the speculative exploratory approach in developing this novel low-cost spectroscopy tool.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

This study aimed to evaluate the early-childhood comorbidities of cerebral palsy (CP) in children with low birth weight (LBW) and assess the impact of maternal bio-psychosocial factors on the risk of CP in preterm infants across varying birth weights. Data for 15,181 prematurely born infants from 2009 to 2013 and 151,810 matched controls from Taiwan's National Health Insurance Research Database were analyzed. Period prevalence of CP, and comorbidities of LBW were verified, and odds ratios (ORs) were calculated. Results confirmed that increasing prematurity and low birth weight (LBW) rates in Taiwan. LBW was associated with higher CP prevalence. Maternal age extremes (&lt;20 and &gt;40 years) were significant risk factors of CP in LBW infants. LBW infants showed higher risks of respiratory, circulatory, and nervous system and psycho-developmental comorbidities compared to controls. Infants with the lowest birth weights had even higher ORs for these comorbidities. However, gastrointestinal and nutritional comorbidities were less prevalent in premature infants. Maternal factors such as family income, number of hospital admissions, and length of hospital stay were significantly correlated with birth weight and subsequent complications. Each additional gestational week significantly reduced the risk of complications in premature infants. Additionally, maternal bio-psychosocial factors were associated with birth weight and related outcomes in premature infants, emphasizing the importance of addressing these factors in prenatal care and interventions.

Abstract—The static and fatigue analysis of plates with holes, made of 2D woven roving composites, is conducted. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches are discussed. The fatigue behaviour is considered with the use of the low cycle fatigue method. The analysis is supplemented by the numerical finite element modeling. The present work is an extension of the results discussed in the literature. The finite element modeling of plates with holes is presented in details in Ref [1-3] including also the problems of the accuracy. The experimental results and the form of specimens are shown in Ref [4]. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The fuzzy approach is employed to reduce the number of experimental data [5].

Utilizing NCEP/NCAR monthly reanalysis data alongside precipitation observations from 1936 monitoring stations across China spanning from 1966 to 2022, this study establishes a location index for the thermal low-pressure center situated over the Qinghai–Tibet Plateau. Temporal variations in the location index and summer (July) precipitation patterns in China were studied. Over the past six decades, thermal low-pressure centers have been predominantly positioned near 90°E and 32.5°N on the plateau, with their distribution extending from east to west rather than from south to north. The longitudinal and latitudinal position indices exhibit contrasting linear trends, with a positive trend observed during the 1970s and early 21st century and a negative trend in subsequent decades. Mutation analysis highlights pronounced weakening mutations occurring in 1981 and 1973, with the longitudinal index transitioning from an inter-annual cycle of approximately 6-8 years, while the latitudinal index displays quasi-cyclic oscillations of 5 and 8 and 12-14 years. Strong negative correlations are evident between the location indices and precipitation along the southeastern edge of the Qinghai–Tibet Plateau and in Southern China, contrasting with the positive correlations observed in the central-eastern plateau, northwest China, North China, and the Huang-Huai region. The influence of southerly airflow predominates over much of China east of the plateau, while northwest China experiences convergence between northerly and southerly airflow. Higher location indices correspond to weaker surface cold air masses and strengthened Western Pacific Subtropical and South Asian Highs south of the Yangtze River Basin, resulting in significantly reduced rainfall in the southern Yangtze River region and increased rainfall in northwest China.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&amp;M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

An imbalance between production and excretion of amyloid β peptide (Aβ) in the brain tissues of Alzheimer’s disease (AD) patients leads to Aβ accumulation and formation of noxious Aβ oligomers/plaques. A promising approach to AD prevention is reduction of free Aβ level by directed enhancement of Aβ binding to its natural depot, human serum albumin (HSA). We previously demonstrated the ability of specific low-molecular-weight ligands (LMWLs) of HSA to improve its affinity for Aβ. Here we develop this approach by bioinformatic search for the clinically approved AD-related LMWLs of HSA, followed by classification of the candidates according to the predicted location of their binding sites on HSA surface, ranking of the candidates, and selective experimental validation of their impact on HSA affinity for Aβ. The top 100 candidate LMWLs were classified into the five clusters. The specific representatives of the different clusters exhibit dramatically different behavior, with 3- to 13-fold changes in equilibrium dissociation constants for the HSA-Aβ40 interaction: prednisone favors HSA-Aβ interaction, mefenamic acid shows the opposite effect, while levothyroxine exhibits the bidirectional effects. Overall, the LMWLs of HSA chosen here provide a basis for drug repurposing for AD prevention, and for search for the medications promoting AD progression.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Cellulose nanofibrils (CNFs) are materials with high aspect ratio. Typically, TEMPO-oxidised, or cationic CNFs consist of long fibrils (up to 2 μm) with very low thickness (less than 10 nm). Derived from their high aspect ratio, CNFs form strong hydrogels with high elasticity at low concentrations. Thus, CNF suspensions appear as an interesting rheology modifier to be applied in cosmetics, paints, foods, as a mineral suspending agent, among other applications. The high viscosity results from the strong 3D fibril network, which is related to good fibrillation of the material, allowing the nanofibrils to overlap. The overlap concentration (c*) was found to vary from ca. 0.13 to ca. 0.60 wt.% depending on the type and intensity of the pre-treatment ap-plied during the preparation of the CNFs. The results confirm the higher tendency for the fibres treated with CHPTAC (cationic) and TEMPO to form a 3D network, resulting in the lowest c*. For the TEMPO-oxidised CNF suspensions, it was also found that aggregation is improved at acidic pH conditions due to lower charge repulsion among fibrils, leading to an increase in the suspension viscosity, as well as higher apparent yield stresses. TEMPO CNF suspensions with low content of carboxylic groups tend to precipitate at moderate acidic pH values.

This article introduces an analytical framework that interprets individual measures of entropy-based mobility derived from mobile phone data. We explore and analyze two widely recognized entropy metrics: random entropy and uncorrelated Shannon entropy. These metrics are estimated through collective variables of human mobility, including movement trends and population density. By employing a collisional model, we establish statistical relationships between entropy measures and mobility variables. Furthermore, our research addresses three primary objectives: firstly, validating the model; secondly, exploring correlations between aggregated mobility and entropy measures in comparison to five economic indicators; and finally, demonstrating the utility of entropy measures. Specifically, we provide an effective population density estimate that offers a more realistic understanding of social interactions. This estimation takes into account both movement regularities and intensity, utilizing real-time data analysis conducted during the peak period of the Covid-19 pandemic.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

In the process of climate change mitigation and adaptation, the focus on climate risk driven by transition innovations has received widespread attention from governments, regulators, and investors. Based on the identification of low-carbon patents through the Green and Low-carbon Technology Inventory in China, this study constructs low-carbon innovation measurements of listed firms in China from 2015 to 2021. Then, an empirical model is used to investigate the impact and mechanism of climate transition innovations on the default risk. The baseline regression model shows that low-carbon innovations can mitigate the default risk of listed firms. Moreover, our findings are supported by instrumental variable regressions that use the time costs of innovation. Finally, the mediation effect demonstrates that investor attention, total factor productivity, and technology spillovers are paths through which transition innovations can affect the default risk. This study reveals that low-carbon technological advances have a positive effect on climate transition risks.

Preschoolers with disabilities and their caregivers have been neglected in health and social service provision in most low-income countries and arguably too in low resourced areas of more affluent nations. Yet as this rapid review of published literature identifies, there are low-cost, evidence-based strategies to address their needs that can be implemented in communities by local people. Five key features of the necessary supports are examined. First the leadership functions required to create and implement the support services. Second, the family-centred, home-based support provided to caregivers and the personnel undertaking this form of support. Third, providing opportunities for peer support to flourish and encouraging the formation of advocacy groups across families. Fourth, mobilizing the support of significant groups within the community; notably traditional healers and leaders; health services and poverty alleviation initiatives. Fifth, devising ways in which preschool educational opportunities can be offered to children as a prelude to their inclusion in primary schools. The review serves a further purpose. It provides an example of how public health researchers and academics could achieve more rapid implementation of evidence-based knowledge into existing and new support services through dissemination to community practitioners.

As a widely used plastic, the aging and degradation of polyethylene (PE) are inevitable problems, whether the goal is to prolong the life of PE products or address the issue of white pollution. Molecular simulation is a vital scientific tool in elucidating the mechanisms and processes of chemical reactions. To obtain the distribution and evolution process of PE's thermal oxidation products, this work employs the self-consistent charge density functional tight binding (SCC-DFTB) method to perform molecular simulations of the thermal oxidation of PE with different crystallinity and branched structures. We discovered that crystallinity does not affect the thermal oxidation mechanism of PE, but higher crystallinity makes PE more susceptible to cross-linking and carbon chain growth, reducing the degree of PE carbon chain breakage. The branched structure of PE results in differences in pore size between the carbon chains, with larger pores leading to a concentrated distribution of O2 and free radicals subsequently formed. The breakdown of PE is slowed down when free radicals are localized in low-density regions of the carbon chain. The specifics and mechanism of PE's thermal oxidation are clearly revealed in this paper, which is essential for understanding the process in-depth and for the development of anti-aging PE products.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

Aiming at the development of the application of massive and heterogeneous LEO constellations, the influence of typical perturbation forces on the orbit prediction of LEO satellites at different altitudes is analyzed. Firstly, the main perturbation force model of LEO satellites is introduced. Then experiments for analyzing the influence of orbit prediction on LEO satellites at different altitudes are designed. Finally, the influence of typical perturbation forces on the orbit prediction under different prediction durations by numerical analysis is assessed systematically, and the orbit prediction of LEO satellites with different non-spherical gravitational field orders, ocean tide orders and atmospheric density models were compared and calculated. The research results show that different orders of non-spherical gravitational fields should be considered when the altitude of satellites is different, the reasonable gravitational field orders for LEO satellites at 500km, 1000km, 1500km and 2000km under 1-hour forecast time are 140x140, 80x80, 60x60 and 40x40 orders, the reasonable orders of ocean tide perturbation for 1500km and 2000km satellites are 20x20 orders. Under the 24-hour forecast time, atmospheric resistance has a great influence on the precision of LEO satellites at orbit altitude below 1,000km. The forecast deviation of the LEO satellites orbit at 500km reaches 8751.576m. The difference of orbit precision between different atmospheric density models is in the meter level. The orbit deviation by the Standard Atmosphere 1976 and NRLMSISE 2000 atmospheric models respectively reaches 25.494m. Relevant conclusions provide support for the optimization and selection of dynamical models in high precision orbit determination and fast orbit prediction of LEO satellites.

Objective: We report a case of acute pancytopenia and liver injury after concomitant administration of low-dose methotrexate (MTX), and high-dose esomeprazole and metamizole. Case summary: A 71-year-old patient with chronic systemic idiopathic erosive arthritis was admitted after a pelvic ring fracture. After hospital admission, she received MTX in addition to esomeprazole and metamizole. Subsequent laboratory tests revealed pancytopenia and elevated liver enzymes. The follow-up clinical examinations were unremarkable, with the exception of sub-febrile temperatures. Further investigations did not detect a definitive etiology. Due to the suspicion of methotrexate-induced hematotoxicity and hepatotoxicity, antagonizing therapy with calcium folinate was administered, after which the blood counts and liver parameters normalized. Discussion: Due to the administration of high-dose metamizole immediately before the administration of low-dose MTX, the pre-existing hematotoxic pharmacodynamic effect of MTX was acutely enhanced by that of metamizole, although folic acid was administered preemptively. In addition, the concomitant administration of high-dose esomeprazole and normal dose torasemide resulted in a pharmacokinetic interaction with MTX by decreasing its renal secretion and elimination, further enhancing the concentration-dependent hematotoxic and hepatotoxic side effects of MTX. Conclusions: The relatively high demand for analgesics in patients with chronic rheumatic diseases already being treated with MTX and proton pump inhibitors necessitates that clinicians consider drug-drug interactions as potential causes of adverse drug reactions after the administration of metamizole or nonsteroidal anti-inflammatory drugs. In this category of patients, it is strongly recommended to switch to analgesics of other classes.

To mitigate the adverse impacts of urban stormwater on streams, watershed managers are increasingly using low impact development and green infrastructure (LID-GI) stormwater control measures such as rain gardens—vegetated depressional areas that collect and infiltrate runoff from rooftops and driveways. Their catchment-scale performance, however, can vary widely, and few studies have investigated the cumulative performance of residential rain gardens for event runoff control in intermediate-sized (i.e., 1-10 km2) suburban catchments. We modeled three years of continuous rainfall-runoff from a 3.1 km2 catchment in Columbia, MD, USA, using the Storm Water Management Model (SWMM). Various extents of rain garden implementation at residential houses were simulated (i.e., 25%, 50%, 75%, and 100% coverage) to determine the effects on peak flow, runoff volume, and lag time. On average, treating 100% of residential rooftops in the catchment reduced peak flows by 14.3%, reduced runoff volumes by 11.4%, and increased lag times by 3.2% for the 223 rainfall events during the simulation period. Peak flow reductions were greater for smaller storm events (p&lt;0.01). Our results show that residential rain gardens can significantly improve the runoff response of suburban catchments, and that they represent an effective and relatively low-cost option for urban watershed management and restoration.

One of the measures required by the European Green Deal to decarbonise the freight transport sector is the promotion of inland waterway transport (IWT), in particular intermodal transport in Europe. To facilitate intermodal transport on the Danube, we developed six new barge designs for the transport of 45' pallet-wide high-cube containers using a four-step approach. Our approach consisted of detailed desk research, followed by design and further analysis of the identified barge types, taking into account, for example, sight lines or stability. The container carrying capacity reaches up to 90 containers in three layers, which is double the capacity of existing standard barges on the Danube. Nevertheless, three-layer transport is hardly feasible in several cases, due to restrictions regarding sight lines and stability. We conclude that each loading condition must be evaluated separately to determine the best barge design option for each case. The study is limited by its geographical scope and the type of container used to develop the new barge designs. This could be a possible direction for further research on this topic: using other container types and/or extending the geographical scope.

Recently, due to the decrease in labor force, increase in labor costs, and the desire for improved quality of life, research on robots has been actively conducted to address these issues. However, it is currently difficult to find robots that physically interact with humans. The reason is that the actuators of robots do not have high torque density on their own. To solve this problem, high torque density motors, such as proprioceptive actuators, are being researched. However, the torque density is still insufficient for physical interaction with humans, so we have developed a motor with higher torque density. However, high torque density motors have the disadvantage of lower speed characteristics due to increased Back-EMF. Therefore, to address the deterioration of speed characteristics in the developed motor, we applied the Independent 3-Phase winding structure to improve the speed characteristics. Consequently, through comparison with Y-Connection and Delta-Connection, we propose the most suitable winding structure for high torque density motors intended for physical interaction with humans.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

Public housing stock, called Social Housing, in Italy developed between the 1950s and the 1980s. As of today, the first residential developments are almost nearing their end-of-life age, in need of urgent and intensive renovation. The European Commission, with the Renovation Wave, has set a goal of doubling the rate of building renovation over the next 10 years, reducing emissions, improving energy performance, and promoting decarburization. Renovation interventions, including structural, functional, energy, plant upgrading, etc., are to be preferred over integral demolition and reconstruction interventions, which have significant repercussions in terms of managerial and social discomfort. The case studies examined concern renovation interventions aimed at energy efficiency, functional adaptation of housing as well as facade restyling. The design variants analyzed were evaluated in terms of CO2e emissions, according to LCI (Life Cycle Inventory) and EPD (Environmental Product Declaration) approaches. This approach has a twofold purpose: to propose design guidelines, with low CO2e emissions, through hypotheses of variants to the case studies, and to propose, to the Economic Operators, economically advantageous bidding scenarios, in the procurement process.

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

Abstract: Purpose: High-grade isthmic spondylolisthesis (HGISL) is a severe condition, associated with low-back pain (LBP) and radiculopathies. The present study is a monocentric prospective observational study investigating the clinical-radiological outcomes of a bilateral minimally invasive TLIF (bm-TLIF) for HGISL. Material and Methods: Patients who underwent bm- TLIF for HGISL at our institution, were considered for inclusion. Clinical-radiological outcomes and complications were collected. Results: Twenty-one patients (14M:7F) were included and the mean clinical follow-up (FU) time was 27(±6) months. There was a significative improvement of the mean VAS-back, VAS-legs, ODI, and SF-36 PCS scores, comparing pre- and last FU measurements. The mean pelvic tilt (p0,05). The univariate analysis showed that residual slip angle (> or  10°) may independently influence VAS-b (p

We will demonstrate that the photon energy density parameter Ωγ of the universe can be derived exactly in Rh = ct cosmology. We find that it must be Ωγ = 1/5760π ≈ 5.52621330180192× 10^(−5). This indicates that there is no uncertainty in the radiation density within at least somesub-classes of Rh = ct cosmology.

Aim: To evaluate the panmacular subthreshold micropulse laser treatment results among patients with central serous chorioretinopathy (CSC) and their correlation with functional and morphological parameters. Material and methods: The examined group included 10 non-treated and 41 treated patients with acute, recurrent, and chronic CSC (13 F, 38 M, mean age 44.11±6.5) and 14 healthy controls (6 F, 8 M, mean age 45±9.3). The BCVA examination, ophthalmoscopy, microp-erimetry, angio-OCT and OCT were performed. The medical history regarding chronic general disorders and known risk factors were recorded. Results: Complete resorption of SRF was obtained in 100% aCSC, 86.66% cCSC, and 63.63% r CSC. BCVA and RetSens significantly improved most of the patients treated in aCSC. The lowest BCVA and RetSens, but the largest pachyvessel and disease duration, were found in rCSC. A strong negative correlation between final BCVA and disease duration was found. No patient demonstrated laser lesions following treatment. Conclusions: The panmacular MPLT therapy leads to long-term enhancement of functional and morphological parameters in all CSC patients. The acute CSC patients showed the most significant improvement. The procedure is safe and could be considered a preferred treatment option for all active CSC cases. Timely treatment is crucial for beneficial outcomes.

Based on recent progress in cosmological thermodynamics, we present a new thermody- namic formulation of the Friedmann equations in the new Haug-Tatum cosmology model, as well as for other similar models put forward in the literature from different solutions to Einstein’s field equation. Since the CMB temperature has been measured much more accu- rately than the Hubble constant, we demonstrate that our thermodynamic formulation of the Friedmann equation dramatically narrows the acceptable range for the critical density of the universe. Furthermore, we show how our thermodynamic formulation leads to a more precise cosmological constant estimate.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

The catastrophic failure of two dams in Libya in the night of 10th and 11th September 2023, resulted in a significant amount of water and debris destroying a large part of the city of Derna, which is located downstream of the two dams. The flood caused more than 6000 fatalities and the dis-placement of thousands of people from the city. The dams failed due to heavy rainfall caused by the Medicane Daniel, resulting in intense precipitation and the dams overspilling after reaching full capacity. This paper analyses the consequences of the dam breach by modelling the flow discharge and the flooding of the city of Derna. The analysis compares the computed quantities with the findings of the post-event satellite image analysis from UNOSAT and Copernicus, the field reports, and information gathered from the social media through AI detection. The results allows to better understand the dynamics of the dam breach, its initial parameters and an assessment of the accu-racy of the results.

The physiological process of iodine uptake in the thyroid is used for 131I treatment of thyroid diseases. Children are more sensitive to radiation compared to adults and may react differently to 131I exposure. The aims of this study were to evaluate the effects on thyroid protein expression in young and adult rats one year after 131I injection, and identify potential biomarkers related to 131I exposure, absorbed dose, and age. Twelve Sprague Dawley Rats (young and adults) were i.v. injected with 50 kBq or 500 kBq 131I and were killed twelve months later. Twelve untreated rats were used as age-matched controls. Quantitative proteomics, statistical analysis and evaluation of biological effects was performed. The effects of irradiation were most prominent in young rats. Protein biomarker candidates were proposed related to age, absorbed dose, thyroid function and cancer and a panel was proposed for 131I exposure. In conclusion, the proteome of rat thyroid was differentially regulated twelve months after low-intermediate dose exposure to 131I in both young and adult rats. Several biomarker candidates are proposed for 131I exposure, age, and many of them are known to be related to thyroid function or thyroid cancer. Further research on human samples are needed for validation.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

Abstract. Introduction: BMD study gives partial information on bone health in patients with TSH suppression therapy due to Differentiated Thyroid Cancer (DTC). TBS, a new parameter of bone microarchitecture is propose for bone quality study. This study analyze their long-term use in patients with DTC. Methods: BMD was measured by DXA and TBS with iNsigth software in 145 postmenopausal DTC patients. Vertebral Fractures (VFs) with a semi-quantitative x-ray method. Results: BMD at the end study was not different from initial. TBS decreased from 1.35±0.1 to 1.27±0.1 (p=0.002). PTH, Osteocalcin, and BAP were increased, suggesting increased bone remodeling. There was an increase in osteoporosis and osteopenia (40.6% and 16.5% to 46.6% and 18.6%); 31% had partially degraded and 15.1% degraded TBS changed to 48,9% and 24,8% at the end study. VFs in 30 patients, was not different in age, BMI, calcium and alcohol ingestion, smoking, radioiodine, or thyroid parameters vs. without VFs. Odds ratio for VFs increased with osteopenia (OR 2.63). Combination of TBS plus TBS did not improve discrimination. Conclusions: TBS was lowered while BMD did not differ. Percentage of osteoporosis and osteopenia and of partially degraded and degraded TBS was higher at the end study. Predominant discordance rate was found in partially degraded microarchitecture, in which the proportion of osteopenia was higher than normal or osteoporotic patients. AUC of TBS plus BMD did not improve discrimination. TBS, radioactive iodine, and sedentary lifestyle were the main differential data for patients with DTC and VFs.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Ovarian cancer (OC) is an umbrella term for cancerous malignancies affecting the ovaries, yet treatment options for all subtypes are predominantly derived from high-grade serous ovarian cancer, the largest subgroup. The concept of "functional precision medicine" involves gaining personalized insights on therapy choice, based on direct exposure of patient tissues to drugs. This especially holds promise for rare subtypes like low-grade serous ovarian cancer (LGSOC). This study aims to establish an in vivo model for LGSOC using zebrafish embryos, comparing treatment responses previously observed in mouse PDX models, cell lines, and 3D tumor models. To address this goal, a well characterized patient-derived LGSOC cell line with the KRAS mutation c.35 G > T (p.(Gly12Val)) was used. Fluorescently labelled tumor cells were injected into the perivitelline space of 2 days post fertilization zebrafish embryos. At 1 day post-injection xenografts were as-sessed for tumor size, followed by random allocation into treatment groups with trametinib, luminespib, and trametinib + luminespib. Subsequently xenografts were euthanized and analysed for apoptosis and proliferation by confocal microscopy. Tumor cells formed compact tumor masses (n=84) in vivo and with clear Ki67 staining, indicating proliferation. Zebrafish xenografts exhibited sensitivity to trametinib and luminespib, individually or combined, within a two-week period, establishing them as a rapid and complementary tool to existing in vitro and in vivo models for evaluating targeted therapies in LGSOC.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

Live video streaming has become one of the main multimedia trends in networks in recent years. Providing Quality of Service (QoS) during live transmissions becomes a challenge due to the stringent requirements for low latency and minimal interruptions. This scenario has led to a high dependence on cloud services, implying a widespread usage of Internet connections, which constrains contexts where an Internet connection is not available. Thus, alternatives such as Mobile Ad Hoc Networks (MANETs) emerge as potential communication techniques. These networks operate autonomously with mobile devices serving as nodes, without the need for coordinating centralized components. However, these characteristics lead to challenges to live-video streaming, such as dynamic node topologies or periods of disconnection. Considering these constraints, this paper investigates the application of Artificial Intelligence (AI)-based classification techniques to provide adaptive streaming in MANETs. For this, a software-driven architecture is proposed to route stream in offline MANETs, predicting the stability of individual links and compressing video frames accordingly. The proposal has been implemented and assessed in a laboratory context, analyzing the model performance and QoS metrics. As a result, the model is implemented in a decision forest algorithm, which provides 95.9% of accuracy. Also, obtained latency values become assumable for video streaming, manifesting a reliable response for routing and node movements.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

: Considering that Einstein's relation between the diffusion coefficient and the drift mobility of the free randomly moving charge carriers in homogeneous materials including metals is always valid, it is shown that the effective electric force acting on free electrons in metal depends on the ratio between the kinetic free electron energy at the Fermi surface to the classical particle energy 3kT/2. The electrical resistivity of elemental metals dependence on very low temperatures has the quadratic term, which has been explained by electron-electron scattering. In this paper, it is shown that the quadratic term of the electrical resistivity at low temperatures is caused by scattering of the free RM electrons by electronic defects due to linear effective free electron scattering cross-section dependence on temperature, but not by electron-electron scattering.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

In this paper, four probability functions are compared with the purpose of establishing a methodology to improve the accuracy of the estimated wind energy in a desert city in northwestern Mexico. For the statistical modeling, 3 time series of wind speed data were used, corresponding to the years 2017, 2018, and 2019, recorded with a sonic anemometer at a sampling frequency of 10 Hz. From these, the analysis is performed with different stationarity periods (5, 30, 60, and 600 seconds). The estimation of the parameters characterizing the probability density functions was performed using different methods; the statistical models were evaluated by the coefficient of determination and the Nash-Sutcliffe efficiency coefficient, while their accuracy by the measured quadratic error, the mean square error, the mean absolute error, and the mean absolute percentage error. It was found that Weibull with the energy pattern factor method and Gamma using the method of moments were the probability density functions that best describe the statistical behavior of the wind speed and, therefore, better estimate the energy generated, so it is concluded that the proposed methodology will allow having greater confidence, both in the estimation of the wind speed and in the small wind energy available for its use.

This paper provides an overview of current literature on community-led development initiatives in urban contexts, their role in addressing urban inequality, and the challenges they face. This study examines effective strategies of community-led initiatives, such as empowering communities, building partnerships, mobilizing resources, focusing on local needs, and participatory design methods. Case studies from around the world demonstrate how successful community-led development initiatives have been able to overcome obstacles to create more inclusive and equitable urban environments. Institutional support, including technical assistance, capacity building, and regulatory frameworks, are crucial for promoting the success and sustainability of these initiatives. Challenges to community-led initiatives include limited resources, capacity building needs, inadequate infrastructure, lack of institutional support, and lack of trust among community members. Therefore, the paper suggests that it is essential to address these challenges to enable the success of community-led development initiatives. Furthermore, this study recommends that future research should explore how emerging technologies and innovative approaches can effectively support community-led development initiatives and advance more just and sustainable urban development.

This study aimed to demonstrate the potential role of Dual Energy CT in assessing Bone Mineral Density (BMD) in postmenopausal women. A retrospective study was conducted on 51 postmenopausal female patients who underwent DXA and DECT examinations for other clinical reasons. DECT images were acquired with spectral imaging using a 256-slice system. These images were processed and visualized using an HAP(fat) map. Statistical analysis was performed using the Bland-Altman method to assess agreement between DXA and DECT HAP(fat) measurements. Mean BMD, vertebral and femoral T-scores were obtained. For vertebral analysis, the Bland-Altman plot showed an inverse correlation (R2: -0.042; RMSE: 0.690) between T-scores and DECT HAP(fat) values for measurements from L1 to L4, while a good linear correlation (R2: 0.341; RMSE: 0.589) it was found for measurements at the femoral neck. In conclusion, we demonstrated the enhanced accuracy of BMD calculation through DECT, finding a statistically significant correlation only at the femoral neck where BMD results do not seem to be influenced by the overlap of the measurements on cortical and trabecular bone. This outcome could be beneficial in the future by reducing radiation exposure for patients already undergoing follow-up for chronic conditions.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

Abstract Cholesterol has ruled the history of atherosclerotic cardiovascular diseases (CVD) for decades, and the transport of cholesterol by lipoproteins has become a cornerstone of our view of etiology of the disease. Discovery of the lipoprotein-specific transport of lipid oxidation products (LOP) has opened a new and exciting area in research of CVD by revealing strong connections between atherogenic LOP, lipoprotein transport functions and CVD. This review goes through the evidence in support of the lipoprotein-specific LOP transport and speculates of possible consequences of the proposed role of lipoprotein LOP transport as a risk factor. Association of lipoprotein LOP with known risk factors of CVD are largely parallel with those of cholesterol, and due to the common transport and cellular intake mechanisms the elucidation of independent effects of either cholesterol or LOP is difficult. Yet, unlike cholesterol, LOP can directly initiate and boost atherogenic processes. It therefore appears inevitable that increasing knowledge of the lipoprotein-specific LOP transport will affect the present view of the role of cholesterol in aetiology and as a risk factor of CVD.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

The transition to sustainable mobility is a recognized socio-economic and environmental challenge, particularly among young adults in low- and middle-income countries (LMICs). This paper addresses the lack of comprehensive research on mobility patterns for LMICs by examining the travel patterns of students, staff, and lecturers at the National Advanced School of Public Works, Yaoundé (NASPW) to understand transport mode choices and barriers to the use of public and active transport modes. Data was collected through online questionnaires from 425 participants. Findings revealed that most students (27.5%) used multiple modes of transport, with moto-taxis being the most common (21%). Lecturers primarily used private cars (50%), while staff relied on taxis or multiple modes (33%). Accessibility, vehicle speed, and flexibility appeared as the most important reasons for the preferred modes of transport. Barriers included long waiting times and traffic congestion for public transport, and distance and inadequate infrastructure for active mobility. The usage of public transportation was encouraged by its affordability and reduced travel time, whilst active options were preferred due to their cost savings and health benefits. To promote sustainable mobility for campus travel, it is crucial to encourage active modes, develop mass transport systems, and raise awareness through symposiums and conferences among students and staff.

We delve into nonrelativistic quantum electrodynamics within a background magnetic field, ensuring gauge invariance via a vector potential. Our exploration extends to the Lagrangian, which incorporates electron self-interactions and electromagnetic field interactions. Through the path integral formalism, we elucidate the effective action, with a specific focus on the photon propagator and screening effects. Examining density and current components reveals Laurent expansions in the hydrodynamic limit. The equations of motion in real space are derived, leading to discussions on phenomena such as Poiseuille-like flow and the Navier-Stokes equation. To ground our theoretical framework at practical contexts, we consider applications such as the fluid dynamics at binary star systems. Depending on the velocity of the expelled fluid, our analysis allows for both nonrelativistic and relativistic treatments, providing a versatile tool for understanding the intricacies of fluid behavior at astrophysical scenarios. Additionally, we recognize that at the presence of a magnetic field, magnetohydrodynamics becomes crucial. While our current focus is at nonrelativistic quantum electrodynamics, the insights gained here contribute to a broader understanding, offering a comprehensive foundation for quantum electrodynamics analysis at diverse physical systems.

This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

This research focuses on exploring generalized electron emissions in one-dimensional conducting materials, specifically examining field emission and thermionic emission. Additionally, the study investigates one-dimensional thermal radiation. The current density is derived for both one-dimensional thermionic emission and one-dimensional field emission. A generalized current density in one dimension is devised, taking into account arbitrary accelerating fields and temperature conditions. The formula for the one-dimensional current density is depicted with accelerating field and temperature across various work function materials. The current is also represented as a function of both temperature and electric field for various temperatures.

Microalgae are highly attractive to various industrial sectors and can serve as indicators of aquatic environmental health. An essential step for cultivating microalgae is assessing the cell density, which is traditionally performed through viable cell counting by optical microscopy (OM). However, this method has some limitations, such as the time involved in the process of counting, and the need for specialized training of laboratory personnel. Spectrophotometry is an affordable alternative, especially when applied to culture growth and toxicological tests. We chose the wavelength of 680 nm to detect the optical density (OD) of the green freshwater microalga Desmodesmus subspicatus and green the marine microalga Tetraselmis sp. The correlation between the number of cells and OD was suitable for both microalgae and accuracy was comparable to traditional OM counting. In toxicological tests, the OD technique allowed the monitoring of microalgal growth in the presence of the chemicals potassium dichromate, potassium chloride and sodium dodecyl sulfate (SDS), with results very close to those reported in the scientific literature. This study sheds light on this well-known technique, which is an important contribution since few articles have explored its potentialities and fragilities, showing the successful application to monitoring green microalgal cultures and toxicological assays.

In China's mountainous coastal terrain, the storm badly damaged low-rise buildings. At present, it is not clear how the relative position of buildings and mountains affects the surface of a low-rise building’s fluctuating coefficient. The study compared these results with the wind pressure distribution without the surrounding environment. The primary objective of this study is to examine the fluctuating coefficient variation rule based on the spacing between hillsides and buildings under 0° wind angle. Additionally, the study analyzes the fluctuating wind pressure coefficient across wind angles between 0°~90°. The distribution of wind pressure in different common hillside landforms was examined through a wind tunnel experiment, which also compared with the distribution in an open environment. The study examined the fluctuating coefficient as the distance between the building and the hillside changed, specifically for wind blowing at a 0° angle. Next, an analysis is conducted on the changing pattern of the fluctuating coefficient for low-rise buildings ranging from a wind angle of 0° to 90°. Simultaneously, the investigation examined the power spectrum and wind pressure’s probability distribution, while considering the proximity of the building to an adjacent hill. The findings indicated that the changing wind pressure factor on the surface of the structure differed based on the relative location of the hillside and the building. The roof's wind pressure coefficient fluctuated and gradually increased until it reached its peak, unaffected by the surroundings. The low-frequency energy decreased in windward eaves, while the high-frequency energy progressively rose as the distance between the hillside and the building increased. The wind pressure on the leeward side exhibited Gaussian characteristics in its probability distribution.

Speeding is a significant global issue, with disparities in speed outcome and speed research between low- and middle-income countries (LMICs) and high-income countries (HICs). This study aims to address speed research gaps by examining the prevalence of self-reported speeding and factors influencing drivers' speeding behavior (SB) using the Theory of Planned Behavior (TPB). An online survey involving 387 anonymous drivers was conducted in Yaoundé. Results showed that all drivers reported exceeding speed limits, with 81% exceeding by 5km/h, 12% by 10km/h, and 7% by more than 10km/h in urban areas. On highways, 54% reported exceeded the limit by more than 10km/h. Age, driver's license, and gender showed significant associations with speed limits non-compliance. The study results suggests that the TPB can be useful in assessing speeding behavior, as the inclusion of TPB variables led to a more than 50% proportionate increase in SB variance. Structural equation modeling revealed attitude towards speeding as the strongest predictor of speeding intention (SI), along with certain demographics indirectly influencing SB through SI. Perceived behavioral control (PBC) and SI directly influenced SB. These findings emphasize the potential of interventions targeting attitude, intentions, and perceived behavioral control to modify speeding behavior and improve road safety.

Two beneficial characteristics of aircraft generators are having armature windings and PM excitation sources placed on the stator side (maintenance and thermal management) and having a clear-cut rotor without permanent magnets or excitation windings (vulnerable at high speeds due to associated centripetal mechanical stresses). Within this framework, a doubly-salient permanent magnet (DSPM) generator was conceived by optimizing the stator size and rotor structure to minimize the torque ripple and maximize the RMS voltage value per turn of each generator phase. A Multi-Objective Design Strategy based on a 2D finite element analysis was used, being set to have characteristics closest to optimal for a Boeing 767 turbine, that is, the necessary electromotive force for a required power of 90 kW at 3000 rpm, feeding a simplified Boeing 767 electrical power distribution system. The results show that the machine could not deliver the required power at 3000 rpm since the 2D finite elements analysis demonstrates that the 2D model gives optimistic results when compared with the 3D FEM model. However, with a 3D finite element analysis of the machine feeding the aircraft load, it was seen that the machine’s efficiency is 92%, suggesting this machine can be a plausible solution.

In the context of carbon neutrality and carbon peaking, in order to achieve low carbon emissions and promote the efficient utilization of wind energy, hydrogen energy as an important energy carrier is proposed to mix hydrogen and natural gas to form hydrogen enriched compressed natu-ral gas (HCNG). It is also injected into the natural gas pipeline network to realize the transmission and utilization of hydrogen energy. At the same time, the participation of demand response is considered, the load peak and trough period is adjusted, and large-scale consumption of renewa-ble energy and the reduction of carbon emissions are realized. First of all, a fine model of hydro-gen production and hydrogen use equipment is established to analyze the impact of adding hy-drogen mixing on the economy and low-carbon of the system. With green certificates and demand response, the utilization rate of hydrogen energy is improved to further explore the energy utiliza-tion rate and emission reduction capacity of the system. Secondly, on the basis of modeling, the optimal scheduling strategy is proposed with the sum of energy purchase cost, equipment opera-tion cost, carbon emission cost, wind curtailment cost and green certificate income as the lowest objective function. Considering the constraints such as hydrogen blending ratio and flexible load ratio of the pipeline network, a low-carbon economic scheduling model of hydrogen mixed natu-ral gas was established. The model was linearized and solved by using MATLAB and CPLEX solver. By comparing different scenarios, the superiority of the model and the effectiveness of the strategy are verified.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Predicting human trajectories poses a significant challenge due to the complex interplay of pedestrian behavior, which is influenced by environmental layout and interpersonal dynamics. This complexity is further compounded by variations in scene density. To address this, we introduce a novel dataset from the Festival of Lights in Lyon 2022, characterized by a wide range of densities (0.2-2.2 ped/m2). Our analysis demonstrates that density-based classification of data can significantly enhance the accuracy of predictive algorithms. We propose an innovative two-stage processing approach, surpassing current state-of-the-art methods in performance. Additionally, we utilize a collision-based error metric to better account for collisions in trajectory predictions. Our findings indicate that the effectiveness of this error metric is density-dependent, offering prediction insights. This study not only advances our understanding of human trajectory prediction in dense environments but also presents a methodological framework for integrating density considerations into predictive modeling, thereby improving algorithmic performance and collision avoidance.

While providing safe water for the rural poor is considered a basic human right, there are numerous issues associated with existing technologies with shortcomings. Performance issues have continued to fail to meet the needs of impoverished families due to issues including high cost, difficulties with performance, and continuing needs for maintenance. These issues have severely interfered the safe water accessibility. Key aspects of the Guelph Water Filter (GWF) system can avoid/minimize many of these issues. The GWF as described herein enables delivery of low cost, long-term performance at 3Log removal of E.coli and can deliver 1 to 3 L of treated water per hour. The GWF is simple to operate, has an ability to provide sufficient water for a family, maintains longevity of performance, is easy to maintain and has protection against breakage during the cleaning process, is repairable at village level, and operates using a sizable reservoir of water to supply raw water, meaning the technology does not need to be refilled frequently. Hence, the capability of the novel GWF technology is shown to bypass many of the troublesome features of alternative low-tech water treatment technologies. The potential for the GWF to function for 2 days continuously avoids the need for young girls to fetch raw water frequently during a day, thereby enabling them to attend school. Hence, the GWF enhances the potential to result in ‘safe water and full schools’, providing the opportunity for girls to receive education and capture socio-economic benefits for the community.

Recently, the composite materials consisting of ionic liquids (ILs) and metal-organic frameworks (MOFs) have attracted a great of attention due to their fantastic properties. Many theoretical studies have been performed towards its special structures and applications. Yet, the mechanism for the diffusion of ILs inside MOFs channels still remain unclear. Here, the DFT calculations together with frontier orbital analysis, natural charge analysis, and energy decomposition analysis were performed to investigate the diffusion behavior of a typical IL, [C4mim][PF6], into the ZIF-8 SOD cage. The potential energy surface (PES) profiles indicate that it is quite difficult for the cation [C4min]+ to diffuse into the cage of ZIF-8 through the pristine pores because of its large imidazole steric hindrance. Moreover, the PES reveals that a success diffusion could be obtained by the thermal contributions, by which the pore size is enlarged through the swing effects at a higher temperature. Subsequently, electronic structure analyses reveal that the main interactions between [PF6]-or [C4mim]+ and ZIF-8 is the steric repulsion interactions. Finally, the effects of amounts of [C4mim][PF6]on the ZIF-8 were investigated, and the results show that two pairs of [C4mim][PF6] per SOD cage is more reasonable in terms of interaction energies and structural changes.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

The speed-density or flow-density relationship is a fundamental aspect of traffic flow theory. Single-regime models often face challenges in consistently fitting empirical data under diverse traffic conditions. This paper addresses the inaccuracies of single-regime models, attributing them not only to their functional forms but also to data dispersion and sample selection bias. To mitigate these issues, the data is segmented into day and night periods, leading to the creation of separate models for each. Calibration results, conducted on data from two freeways, Tehran-Karaj and Tehran-Qom, reveal distinct challenges, with the former exhibiting high dispersion and the latter showing low dispersion. Surprisingly, single-regime models demonstrate notable effectiveness when applied to distinct day and night data. Further analysis, categorizing data into day and night, results in reduced errors (20-60% improvement in R-Square), emphasizing the potential for enhanced accuracy by considering distinct regimes. Overall, the study underscores the significance of regime-specific considerations for accurate traffic flow modeling. Upon thorough evaluation, the study highlights the superiority of the neural network Multi-layer Perceptron (MLP) over traditional models. The research discusses the implications of incorporating day and night parameters into the models, emphasizing their potential for accuracy enhancement.

The Sanaga River Valley is a deep-seated structure of about 220 km in width, bounded on its northern and southern sides by 025-0550 fault zones. Its internal structure has been very little described before this study. It is characterized by the presence of surface features where a thick stratum of shale and argillaceous sandstones have been documented. The use of electrical resistivity tomography for near-surface imaging and hydrogeological prospecting within shale succession is widespread. However, several methods of spatial modeling of resistivity contours are generally proposed for the interpretation of inverse resistivity model sections. To determine the most appropriate method for interpreting resistivity tomographies in the context of subsoil marked by significant heterogeneity, logarithmic contour intervals, and linear contour interval processing were implemented on data collected over five areas. The data consists of outcrops data, cuttings samples from groundwater boreholes, and resistivity sections ranging in length from 240 to 1000 m. Well-control of the inverse resistivity model sections derived from both processes shows that the linear contour intervals modeling gives a more realistic picture of the reservoir size of the wa-ter-bearing sand in both shale and argillaceous sandstone succession. The sedimentary architecture over Sanaga fault breccia is marked by vertical intrusion anomalies up to 80 m high. The shape of these anomalies, as well as the very low resistivity values that characterize them, suggests that they could be related to mud intrusion.

Residual sugars (RS) in wine are the sugars that remain in a wine after fermentation is complete. In some wine styles, such as semi-dry wines, the accurate measurement of the RS concentration is critical for both qualitative and legislative reasons. Brix, measured by a simple refractometer, can give a good estimation of the RS concentration in the must, but during fermentation, the presence of alcohol leads to inaccurate sugar measurements. In order to measure the RS accurately, other more precise techniques are used, most of which are expensive or require professional skills. Therefore, novel approaches for rapid, easy, and practical measurements for estimating the sugar content were suggested over the years. However, most of these methods do not supply an actual measurement of RS but rather give brix values, and those that measure RS involve special equipment, which is less relevant for small wineries. This study suggests a novel model for predicting and controlling the wine's residual sugar. The data the model uses is the initial brix of the must before fermentation and its density during fermentation. The model was created by measuring actual residual sugars during the fermentation of natural and synthetic musts, with various degrees of initial brix levels, while simultaneously measuring their densities and correlating the two measurements. Linear regression between the residual sugar of the wine and its density was obtained for all treatments and repetitions (i.e., different values of must initial brix) with R² values above 0.97. Using the model, one can calculate (before commencing the fermentation) the density values at which the fermentation will reach a particular desired residual sugar value for a specific initial brix level; the model is applicable for the fermentation conditions used in this work, i.e., brix levels of 18-27˚Bx, Saccharomyces cerevisiae strains (fx-33 and fx-10) in common conditions of fermentation regarding temperature and aeration.

(1) Background: This paper details the development process of two assistive technology products (ATs) implemented in the PAID project, aiming to promote the social, educational, and labor inclusion of people with disabilities across 10 municipalities of Antioquia, Colombia. (2) Methods: Applying Design Thinking (DT) methodology, including stages of empathizing, defining, ideating, prototyping, and testing, alongside a demographic study where specific needs of people with disabilities (PwDs) were identified. (3) Results: As a result, the construction process of two specific cases of assistive technology products (ATs) is detailed, including finite element simulation, mechanical testing, and delivery to end-users. Additionally, workshops for assistive product fabrication conducted in select municipalities of the project are highlighted. (4) Conclusions: the information gathered guided the development of the ATs, focusing on their features on accessibility and ease of replication. The primary objective is to facilitate the participation of PwDs in educational environments, thus promoting inclusion and accessibility. This article describes the results of two of these ATs; however, it is worth noting that this process was performed for 112 ATs delivered through the duration of the project.

A regional modern river-sand geochemical mapping study in the majority of the Timor-Leste territory, including the research area, has not been previously reported. This study demonstrated the potential of modern river sand geochemical mapping as an effective method for lithological mapping, particularly in areas that face challenges in conducting efficient geological fieldwork and have limited geological information. A total of 53 modern river sand samples were collected and analyzed. Before examining the samples using wavelength-dispersive X-ray fluorescence for ten major elements, the loss-on-ignition method was employed. In the Clerec drainage basin, SiO2, CaO, and K2O showed positive correlations, and CaO was positively correlated with MnO. Similarly, in the Sahe River catchment, a positive relationship was observed between CaO, MnO, and TiO2. These findings suggested the presence of quartz, manganese, secondary K-bearing minerals, and secondary Ti-bearing minerals in carbonate rocks that have undergone silicification and other alteration processes. The principal component analysis results corroborated the SiO2/Al2O3 and K2O/Na2O ratios and the ICV findings. PC1 was related to the variations in Ca-poor and Ca-rich rocks; PC2 indicated notable inputs from SiO2-rich and SiO2-poor rocks; and PC3 revealed the possibility of contributions from secondary mineral assemblages related to silicification and low-grade metamorphic processes.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

In general, a superconductor has zero resistance, although it requires significant refrigeration or high pressures with high manufacturing costs, which prevents it into practical applications. In other words, solving these issues implies main superconducting researches. To solve these problems, this paper describes a new type of superconductivity, which is independent for temperatures and which operates without pressures. The principles of the presented system are as follows:First a voltage source, a current source and a load are connected in series. Then, the voltage of the voltage source is adjusted to balance the voltage of the load. Under this condition, the balance of the two voltages provides a zero voltage between the taps of the current source and the generated current from the voltage source becomes zero because of the internal infinite resistance of the current source. As a result, the electric powers generated by the two sources are zero, and therefore, the load cannot generate Joule heating because of energy conservation. However, the current from the current source (not the voltage source) is not zero; therefore, we can predict that the resistance of the load must be zero. As a theory, we derived a new electric field and transient attractive force, which result in a very short coherence of an electron pair because there is not the Coulomb repulsive force due to the existence of the above transient attractive force. Note that both the forces are derived by the Poisson equation, which implies that they cannot be compatible. Therefore, the pair combination energy from spins becomes extremely strong, which is not destroyed by the normal heat energy. Moreover, every center-of-mass motion of electron pair results in the Bose-Einstein condensation and the macroscopic wave function, which produces the London equation (i.e., the Meissner effect). Moreover, by introducing the equivalent circuit, this paper conducted numerical calculations. As a result, we could derive numerically zero resistance and responses for additional static magnetic fields as a discharged current, which implies the Meissner effect. Note that this paper has prepared Appendix section, which provides a guide to reproduce actual experiments and preliminary experimental results. These results in the Appendix indicate the zero resistances and Meissner effects.

The hard open problem of finding the lower bound for the Fokker Planck Kolmogorov’s time-dependent controller parameter probability density function is addressed for the first time in literature in this work. This revolutionary exposition will put control theory and other related inter-disciplinary fields to a higher level towards contemporary control theory. Notably, based on the influential role of control theory in both engineering and industry, this paper will be of great value to all engineering and industry professionals who seek to know more about advanced trends within control theory settings. On the other remit of the spectrum, Fokker Planck Kolmogorov(FPK) equations are of high importance to physicists as well as mathematicians, based on their multiple applicability to multi-interdisciplinary fields of human knowledge, and beyond. So, this by default adds more taste and credibility to this study. Concluding thoughts are included at the end of the work along with a difficult outstanding problem and the direction of future work.

Climate change has become a global nightmare, and the awareness of the causes of carbon emissions have resulted in rigorous studies. These studies linked the increase in global warming with booming economic growth. Since global warming has become more apparent, researchers have explored ways to decouple economic activities from carbon growth. Economic and carbon growth must be decoupled to achieve a low-carbon economy to support the carbon growth plan or emission reduction strategy. The world is transitioning towards a carbon-neutral and green ecosystem, so finding ways to decouple carbon emissions from economic activities is an exciting topic to explore. The study reviews current information on the importance of decoupling energy from economic growth innovative techniques that thoroughly examine the challenges and constraints of low-carbon energy systems. This review revealed that decarbonization and dematerialization had been achieved without declining global economic growth. It also provides information on energy use and economic activities leading to global carbon emissions and alternative solutions to the global challenge of climate change. The decoupling methods commonly used to determine the impact of energy decarbonization on economic growth are explored. All suggested that economic growth is a primary mover of global carbon emission increase and must be separated to achieve a carbon environment.

This work is the first in literature to tackle the difficult open problem of determining the upper bound and threshold theorem for the TDCDP (time-dependent controller parameter) of the (Fokker Planck Kolmogorov) probability density function. This revolutionary exposition will put control theory and other related inter-disciplinary fields to a higher level towards contemporary control theory. Notably, based on the influential role of control theory in both engineering and industry, this paper will be of great value to all engineering and industry professionals who seek to know more about advanced trends within control theory settings. On the other remit of the spectrum, Fokker Planck Kolmogorov(FPK) equations are of high importance to physicists as well as mathematicians, based on their multiple applicability to information theory, graph theory, data science, finance, economics, and beyond. So, this by default adds more taste and credibility to this study. This leads by nature to introducing a different flavor to this ground-breaking research by highlighting the impact of Fokker Planck Kolmogorov(FPK) to revolutionize crypocurrency,which have received its name because it uses encryption to verify transactions, a new debatable digital payment system that doesn't rely on banks to verify transactions. It’s a peer-to-peer system that can enable anyone anywhere to send and receive payments. The paper ends with closing remarks combined with some challenging open problems and the next phase of research.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

GNSS is nowadays a standard tool for monitoring and studying the Earth’s dynamic environment. However, the development of dense GNSS measurements remains limited in many experiments by the cost of geodetic-class equipments allowing to achieve the high precision required by many applications. Recently, multi-constellation, multi-frequency, low-power and, above all, less expensive GNSS electronic chips have become available. We present a prototype of a low-cost, open-source multi-GNSS station. Our prototype comprises a dual-frequency GNSS chip, a calibrated antenna, a Raspberry Pi card and a 4G key for data transmission. The system is easy to deploy in the field and allows precise positioning in real time and post-processing. We assess the performance of our prototype in terms of raw data quality, and quality of the obtained high rate and daily position one-year-long time series. Our results demonstrate a quality equivalent to geodetic-class equipment and better quality than other low-cost systems proposed so far.

The paper explores the Kullback-Leibler divergence formalism (KLDF) applied to the stable MG1 queue manifold. More potentially, both service time probability and cumulative functions which make KLDF exact are obtained. The credibility of KLDF is justified through consistency axioms. Some potential applications of Kullback-Leibler divergence to Biometry are presented. The paper concludes with closing remarks combined with some challenging open problems and the next phase of research.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.