The thermal decomposition of siderite and its decomposition products in a vacuum atmosphere was investigated for the first time using in situ high-temperature transmission Mössbauer spectroscopy. These measurements were supported by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, and magnetic measurements. In situ Mössbauer spectra were collected from room temperature (RT) to 750 oC with a temperature step of 50 oC. After that, the sample was cooled down to RT with step 100 oC. Raw siderite samples contain siderite as the only iron-bearing mineral, and after heating the samples at high temperatures, hematite and magnetite are only Fe-bearing phases. In the temperature range of 300 oC - 500 oC, siderite decomposition occurs. The analysis shows that siderite transforms directly into magnetite, and then hematite generation occurs as long as siderite is present in the sample. Changing hyperfine parameters like isomer shift, quadrupole splitting, or hyperfine magnetic field versus temperature were obtained for siderite and iron oxides (hematite, magnetite). The measurements also show that magnetite formed during the decomposition of siderite is a composition of particles of various sizes and a low degree of crystallization.

Melting phase relations of the diamond-forming system olivine (Ol) – jadeite (Jd) – diopside (Di) – (Mg, Fe, Ca, Na)-carbonates (Carb*) – (C-O-H-fluid) are studied in experiments at 6.0 GPa in the polythermal section Ol74Carb*18.5(C-O-H)7.5 - Omp74Carb*18.5(C-O-H)7.5, where Ol = Fo80Fa20, Omp (omphacite) = Jd62Di38 and Carb* = (MgCO3)25(FeCO3)25(CaCO3)25(Na2CO3)25. Peritectic reaction of olivine and jadeite-bearing melt with formation of garnet has been determined as a physico-chemical mechanism of ultrabasiс-basiс evolution of the diamond-forming system. In the process CO2-component of the supercritical C-O-H-fluid can react with silicate components to form additional carbonates of Mg, Fe, Ca and Na. Solidus temperature of the diamond-forming system is depressed to 1000-1020°C by joint effect of the H2O-fluid and carbonate constituents thereof. The experimentally recognized peritectic mechanism of ultrabasiс-basiс evolution of the diamond-forming system explains the origin of the associated paragenetic inclusions of peridotite and eclogite minerals in diamonds as well as the xenoliths of diamond-bearing peridotites and eclogites of the kimberlitic deposits of diamond. The diamond-forming systems have formed with the use of material of the upper mantle native peridotite rocks. In this case the capacity of the rocks to run the peritectic reaction of olivine was transmitted with silicate components to the diamond-forming systems.

Rotor blade bearings enable the rotor blades to pivot about their longitudinal axis and thus control the power output and reduce the loads acting on the wind turbine. Over a design period of 20 years, rolling bearings are exposed to frequent oscillating movements with amplitude ratios of x/2b>1, especially due to new control concepts such as Individual Pitch Control, which can lead to wear and a reduction in service life. The objective of the paper is to identify the dominant wear mechanisms and their consequences for the operation of oscillating bearings. Oscillating experiments with increasing number of cycles on angular contact ball bearings of two different sizes (type 7208 and 7220), show that the damage initiation starts with adhesive and corrosive wear mechanisms, which result in a sharp increase of the torque as well as the wear volume on the bearing raceway. As the number of cycles increases, an abrasive mechanism occurs, resulting in a lower slope of the wear curve and a smoothing of the resulting wear depressions. The wear and torque curves are evaluated and classified using an energy-wear approach according to Fouvry.

Two billion people worldwide suffer from anemia with reproductive-age women being disproportionately affected. Iron plays a crucial role in cellular function and impacts cognition, physical function, and quality of life. Iron deficiency (ID) and iron deficiency anemia (IDA) are associated with adverse effects on pregnancy and fetal development. Oral iron supplementation has been the standard treatment for IDA for decades often producing sub-optimal outcomes. Many babies are still being born with ID and suffer adverse sequelae due to inadequate iron levels in the mothers. Is it time to consider broad scale-up of parenteral iron as a new standard of care?

Iron deficiency (ID) is by far the most common nutritional disorder in developing and developed countries. When left untreated, ID leads to anemia. Although the usual recommended treatment for iron deficiency anemia (IDA) is oral iron therapy with countless products, such therapy necessitates administration for >3-6 months with questionable patient compliance since most oral iron products have an unpleasant metallic aftertaste and cause intestinal side effects. In addition, in certain gastrointestinal conditions, such as inflammatory bowel diseases or untreated gluten-sensitive enteropathy, oral iron therapy is contraindicated or unsuccessful. Intravenous iron is considered safe in adults, where adverse events are mild and easily managed. The experience with parenteral iron in children is much more limited and many pediatricians appear reluctant to use it because of uncorroborated fears of serious anaphylactic reactions. In the current article, we thoroughly review the available pediatric literature on the use of all commercially available parenteral iron products except ferumoxytol, which was recently removed from the market. We conclude that parenteral iron appears to be safe in children, it works faster than oral iron and the newer third-generation products allow replacement of the total iron deficit at a single setting.

To increase the power density of the electromechanical drive train of wind turbines, journal bearings can be used as planetary gear bearings instead of rolling bearings. This technological change presents new challenges. For example, wind turbine drive systems are subject to dynamic and low-speed operating conditions which can lead to an accelerated abrasive wear of the journal bearings. In addition, oil supply failure or peak loads due to wind gusts and grid and power converter faults could potentially result in catastrophic failure due to adhesive wear in a very short time. Such operating characteristics are, therefore, critical regarding the journal bearing wear lifetime and must be considered in the design. The successful implementation of journal bearings in wind turbines depends on a reliable estimation of adhesive and abrasive wear. In this paper, five different models for the wear calculation of journal bearings are evaluated regarding their suitability of wear calculation of planetary gear bearings in wind turbines. For this purpose, the following evaluation criteria were defined: parameter uncertainty, parametrization effort, in particular number of parameters, parameterization method and load case dependency of parameters and calculation effort. In order to be able to evaluate the wear models, the wear models are numerically implemented and the wear of a test journal bearing is exemplarily calculated under load conditions, which are comparable to load conditions in a wind turbine. Relevant influences from the wind turbine system such as lubricant, material and manufacturing dependent surface influences like roughness and hardness are considered. The wear models are evaluated with respect to their fulfillment of the defined criteria. The resulting evaluation allows the selection of a wear model that can be used to calculate the wear of planetary gear journal bearings in wind turbines, considering the available input variables.

Mechanical power and motion are often transmitted by the gear-rotor-bearing system. When there are fitting clearances between the housing and outer ring in bearings, complex vibration responses will be generated, which makes the operating status difficult to identify. Therefore, for analyzing dynamic responses, a dynamic model of gear-rotor-bearing systems with bearing fitting clearances is proposed. In the model, the bearing system with fitting clearances and gear pair system are combined, and the coupling relationship is determined by the gyroscopic mo-tion of the shaft. The friction force and collision force caused by fitting clearances are also con-sidered, which are simulated by the Coulomb friction model and Hertz theory. The result shows that the meshing stiffness will also be excited by the bearing displacement. When there are fit-ting clearances on the bearing, the amplitude modulation of the bearing outer raceway to the system time-domain response is intensified, and the multiple harmonic frequency of bearings and gear pairs are generated on the spectrum, as well as defect frequencies of gear pairs. As the fitting clearance is increased, the higher multiple harmonic responses will be caused. Although the response amplitude of the gearbox is increased by raising the input speed, multiple harmon-ic responses are suppressed, which makes the system mainly vibrate at the fundamental fre-quency. Then, the dynamic model and the vibration analysis are experimentally verified.

Introduction: In the recent years alternate day dosing has been recommended in iron deficieny treatment. The aim of this study is to compare the efficacy and side effects of oral iron treatments given daily 1x1, alternate day 1x1 and 2x1 alternate day dosing in iron deficieny anemia patients. Methods: A total of 52 patients with a diagnosis of iron deficiency anemia with serum ferritin level of 25 µg/L or less were included in this retrospective study. Statistical analyzes were done with SPSS V.25. Results: The patients included in our study were between the ages of 18-51. All of the patients included in the study were female. A statistically significant increase was found between 0-14 days(p<0.001), 14-28 days(p<0.001) and 0-28 days(p<0.001) hemoglobin values in all patients. There was no statistically significant difference between 0-14 days (p=0.397) and 0-28 days(p=0.310) ferritin values in all patients. A statistically significant difference was found between 14-28 days(p<0.001) ferritin values. When the rate of change of hemoglobin and ferritin values between the groups was compared and no statistically significant difference was observed between the groups. The rate of change of ferritin values for 14-28 days was significant (p=0.012). There was no significant difference in the frequency of symptoms in the 14th day and 28th day controls for each group (p>0.05). The incidence of metallic taste and bloating symptoms was found to be statistically significant in the third control in the group with 2x1 drug use alternate day (p=0.094). Discussion: The only difference in efficacy was observed in ferritin values between 14th and 28th days. The increase in ferritin values was higher in the group that used 1x1 oral iron every day. However, since no difference was observed between the groups in terms of ferritin and hemoglobin values on days 0 and 28, all three groups were considered equally efficient. Side effects were mainly gastrointestinal side effects. Since the group that received 2x1 oral treatment alternate day had a statistically significantly higher rate of side effects, the patients’ treatment tolerance will be lower compared to the other groups. In conlusion, there is no difference in efficacy and side effects between the patient groups receiving 1x1 daily and 1x1 alternate day oral iron therapy, so 1x1 use alternate day is the most appropriate treatment method for oral iron therapy in terms of patient tolerance, adherence to treatment and pharmacoeconomics.

β-thalassemia, a congenital genetic hematological disorder characterized by decreased or absence of β-globin chains, leads to decrease in levels of Hemoglobin A. The affected individuals can be categorized into two cohorts based on transfusion dependency: transfusion dependent thalassemia (TDT) and non-transfusion dependent thalassemia (NTDT). Remarkably, despite the primary pathology lying in β-globin chain depletion, β-thalassemia exhibits an intriguing association with iron overload. Iron metabolism, a tightly regulated physiological process, reveals a complex interplay in these patients. Over time, both cohorts of β-thalassemic individuals develop iron overload, albeit through distinct mechanisms. Addressing the diverse complications arising due to iron overload in β-thalassemic patients, the utilization of iron chelators has gained a lot of significance. With varying efficacies, routes of administration, and modes of action, different iron chelators offer unique benefits to patients. In the Indian context, three commercialized iron chelators have emerged, showcasing a high adherence rate to the iron chelator-based treatment regimens among β-thalassemic individuals. In this review, we explore the intriguing connection between β-thalassemia and iron overload, shedding light on the intricate mechanisms at play. We delve into the intricacies of iron metabolism, unveiling the distinct pathways leading to iron accumulation in these patients. Additionally, we critically evaluate the therapeutic efficacy of different iron chelators, emphasizing their respective advantages in managing iron overload complications. Through this comprehensive analysis, we aim to deepen our understanding of β-thalassemia and iron overload, paving the way for optimized treatment strategies. Ultimately, our findings provide valuable insights into improving the care and outcomes of individuals affected by β-thalassemia.

JIS SUJ2 is most widely used in bearing steels. The advantages are good hardenability, excellent fatigue, wear resistance and comprehensive mechanical properties. For wear resistance and fatigue resistance of the steel are getting more and more attention, the residual stress state and its distribution on the surface of the heat affect zone are critical factors affecting the fatigue life and wear resistance of the parts. In this study, using the SUJ2 as the material to talk about the surface residual stress and retained austenite distribution. Doing the quenching and tempering treatment to obtain different microstructures, using the induction method to re-quench the case region. After the heat treatment, measuring the residual stress and retained austenite volume on the surface by X-ray diffraction, observing the microstructure and comparing the hardness. The results show that the microstructure after heat treatment contains unsolidified carbides, tempered martensite and retained austenite. The residual stress on the surface is the tensile state. In the re-hardened area after induction quenching, the residual stress is all compressive, and the values are more than -800 MPa. In conclusion, in the same output power condition can be observed that the microstructure of the specimens before induction hardening has a significant impact on the effective case depth. The surface residual stress has changed from a tensile to a compressive state. In the re-hardened area, the maximum of the residual compressive stress increased with the austenitized temperature increase.

Efficiency improvement is the new challenge in all fields of design. In this scenario the reduction of power losses is becoming more and more a main concern also in the design of power transmissions. Appropriate models to predict power losses are therefore from the earliest stages of the design phase. The aim of the project is to carry on lubrication simulations of several variants of a cylindrical-roller-bearing to understand the lubricant distribution and the related churning power losses. Several strategies to reduce the computational effort have been used. Among them the sectorial symmetry and three innovative meshing strategies (purely analytical with and without interfaces and analytical/subtractive) that have been implemented in the OpenFOAM® environment. The results of the different approaches were compared among them and with experimental observations showing good agreement and reasonable savings in terms of computational effort.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

Antarctic krill protein-iron complex and peptide-iron complex were obtained to investigate their iron bioavailability, expression of iron-regulated genes, and in vivo antioxidant capacity. Results indicated that Antarctic krill peptide-iron complex increased significantly the hemoglobin (Hb), serum iron (SI) and iron content in the liver and spleen in iron-deficiency anemia (IDA) mice (P < 0.05) compared with those of Antarctic krill protein-iron complex. Despite the gene expressions of divalent metal transporter 1(DMT1), transferrin (Tf) and transferrin receptor (TfR) could be better regulated by both Antarctic krill peptide-iron complex and protein-iron complex, the relative iron bioavailability of the Antarctic krill peptide-iron complex group (152.53±21.05%) was significantly higher than that of the protein-iron complex group (112.75±9.60%) (P<0.05). Moreover, Antarctic krill peptide-iron complex could enhance the antioxidant enzyme activities of superoxidase dismutase (SOD) and glutathione peroxidase (GSH-Px), reduce the malondialdehyde (MDA) level in IDA mice compared with the protein-iron complex, reducing the cell damage caused by IDA. Therefore, these results demonstrated that Antarctic krill peptide-iron complex could be used as a highly efficient and multifunctional iron supplement.

Background: Iron chelation medications (desferoxamine, desferasirox, desferiprone) are used to manage iron overload. These medications are partially excreted via the kidneys, desferoxamine and desferiprone excretes primarily in the urine, and desferasirox had about 8% excreted in the urine. Their use in severe kidney disease and dialysis patients is caution as “avoided” concerning adverse effects; however, there are reports safe use. This manuscript reviews the literature in this population. Data Sources: Pubmed: desferasirox, deferiprone, deferoxamine, kidney disease, ESKD, Dialysis. Case reports and case series that described experiences with using iron chelation medications in ESKD patients are included. Data also gathered from reading-related sources. Results: This is a review of desferoxamine, desferasirox, and deferiprone use in kidney disease from 1976 to the present time. Table 1 provides a summary of findings. These are mostly reports and brief descriptions of the experiences used in severe kidney disease and dialysis, but lack of randomized control trials and small number of participants. Conclusions: Iron chelation medications are important for treating iron overload but concerns with adverse effects. Due to limited medications available to treat iron overload in patients with severe kidney disease, their safe use has been reporting in the literature. This is an area that warrants further research.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

In Ecuador, particularly in the El Oro province, gold mining has been historically hampered by arsenic contamination in the ores. This research addresses the persistent issue of arsenic in gold-bearing ores from Miraflores Mine in Cerro Azul, Atahualpa Canton, and the challenges it presents to mining operations. The study's purpose is to evaluate the effectiveness of an alkaline leaching process for arsenic removal. The ore underwent thorough characterisation, employing advanced techniques like fire assay and atomic absorption. Once the ore's nature was discerned, an arsenic extraction experiment using a leaching solution was conducted. The implemented process achieved an arsenic removal efficiency of 90.54%. This enhanced ore quality facilitates efficient metallurgical applications and, more notably, reduces the environmental footprint by diminishing the need for harmful reagents like sodium cyanide. However, a significant implication of this method is the added cost due to the need for heat during the leaching test, amounting to an approximate $30 per ton increase. The alkaline leaching process emerges as a promising solution for arsenic challenges in El Oro’s mining sector. While the findings are encouraging, further expansive tests are recommended to validate the results and underscore the urgency for sustainable and hazard-conscious mining practices.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

(1) Background: Ferric carboxymaltose (FCM) is an intravenous (IV) high-dose iron that is effective in the treatment of iron deficiency anemia. This study was to determine if preoperative IV FCM administration could improve recovery from postoperative anemia in patients undergoing revision total joint arthroplasty. (2) Methods: This prospective randomized controlled study analyzed 82 patients undergoing revision total joint arthroplasty during a single hospitalization. Patients in the iron group (n = 41) were administered 1000 mg of IV FCM two weeks preoperatively, while those in the control group (n = 41) were not. Moreover, patients with anemia defined as a preoperative suboptimal Hb concentration &lt;13.0 g/dl were compared according to IV FCM administration. The absolute Hb levels and changes in Hb levels, iron profiles, transfusion rate, and EuroQOL 5-dimension (EQ-5D) scores were compared. (3) Results: There were no significant differences in recovery of Hb levels at each timepoint between the two groups; however, the changes in Hb levels from baseline to four weeks postoperatively showed marginally significant differences favoring the iron group (p = 0.052). However, for preoperatively anemic patients, the change in hemoglobin (Hb) levels between baseline and four weeks postoperatively was significantly better in the iron group than in the control group (iron group [n = 26], −0.3 ± 0.7 g/dL vs. control group [n = 27], −0.9 ± 0.8 g/dL; p = 0.040), although the absolute Hb levels, transfusion rates, and patient quality of life were comparable (all p &gt; 0.05). The iron group showed improved iron metabolite levels including serum ferritin and transferrin saturation four weeks postoperatively, and no adverse events associated with IV FCM administration occurred in either group. (4) Conclusions: Preoperative IV FCM in anemic individuals undergoing revision joint arthroplasty was effective in accelerating recovery from surgery-related anemia by improving Hb levels without any adverse events, despite similar actual Hb levels between the groups. Our findings are clinically relevant and can facilitate determination of the suitability of IV FCM as a safe and reliable protocol for iron supplementation for anemia correction.

In pigs, iron deficiency anemia (IDA) is the most prevalent deficiency disorder during the early postnatal period frequently developing into a critical illness. Meanwhile, in humans, only low-birth-weight infants, including premature infants are especially susceptible to developing IDA. In both human and pig neonates, the initial cause of IDA is low birth iron stores. In piglets this shortage of stored iron results mainly from genetic selection over the past few decades for large litter size and high birth weight. In consequence, pregnant sows cannot provide sufficient amount of iron to the increasing number of developing fetuses. Supplementation with iron is a common practice for the treatment of IDA in piglets. For decades, the preferred procedure for delivering iron supplements during early life stages has been through the intramuscular injection of large amount of iron dextran. However, this relatively simple therapy, which in general, efficiently corrects IDA, may generate toxic effects, and by inducing hepcidin expression, may decrease bioavailability of supplemental iron. New iron supplements are considered now with the aim to combine improvement of hematological status, blunting hepcidin expression, and minimizing toxicity of the administered iron. We propose that iron-deficient piglets constitute a convenient animal model for performing pre-clinical studies with iron supplements.

Iron is an essential nutrient and necessary for biological functions from DNA replication and repair to transcriptional regulation, mitochondrial respiration, electron transfer, oxygen transport, photosynthesis, enzymatic catalysis, and nitrogen fixation. However, due to iron’s propensity to generate toxic radicals which can cause damage to DNA, proteins, and lipids, multiple processes regulate uptake and distribution of iron in living systems. Understanding how intracellular iron metabolism is optimized and how iron is utilized to regulate other intracellular processes is important to our overall understanding of a multitude of biological processes. One of the tools that the cell utilizes to regulate a multitude of functions is ligation of the iron-sulfur (Fe-S) cluster cofactor. Fe-S clusters comprised of iron and inorganic sulfur are ancient components of living matter on earth that are integral for physiological function in all domains of life. Here we will explore the ways in which the cell utilizes Fe-S clusters to sense the intracellular environment and respond to maintain equilibrium.

Oral ferric citrate hydrate (FCH) is effective for iron deficiency in hemodialysis patients.; however, it remains unclear how iron balance in the body affects iron absorption from the intestinal tract. This prospective, observational study (Riona-Oral Iron Absorption Trial, R-OIAT, UMIN 000031406), conducted at 42 hemodialysis centers in Japan, wherein 268 hemodialysis patients without inflammation were enrolled and treated with a fixed amount of FCH for 6 months. We assessed the predictive value of hepcidin-25 for iron absorption and iron shift between ferritin (FTN) and red blood cells (RBCs) following FCH therapy. Serum iron changes at 2 h (ΔFe2h) after FCH ingestion were evaluated as iron absorption. The primary outcome was the quantitative delineation of iron variables on ΔFe2h and the secondary outcome was the description of the predictors of body iron balance. Generalized estimating equations (GEE) were used to identify the determinants of iron absorption during each phase of FCH treatment. ΔFe2h increased when hepcidin-25 and MCH decreased (-0.155, -0.242 to -0.068, p = 0.001; -2.574, -4.421 to -0.726, p = 0.006, respectively) in GEE. Hepcidin-25 increased when erythropoiesis-stimulating agent (ESA) decreased (-0.002, -0.002 to -0.001, p=0.000). FTN increased when RBC and ESA decreased (-0.466, -0.605 to -0.327, p=0.000; -0.002, -0.004 to -0.000, p=0.05, respectively. Limiting erythropoiesis to maintain hemoglobin levels induces RBC reduction in hemodialysis patients, resulting in increased hepcidin-25 and FTN levels. Hepcidin-25 production may prompt an iron shift from RBC-iron to FTN-iron, inhibiting iron absorption even with continued FCH intake.

This study addresses the critical issue of dowel-bearing strength in Bambusa blumeana, a key sus-tainable construction material crucial for climate change mitigation. Given the lack of bamboo connection standards, the research focuses on determining the dowel-bearing strength of Bambusa blumeana, emphasizing factors such as dowel diameter, node placements, and the physical prop-erties of bamboo. A predictive equation is derived, enhancing the practicality of bamboo in struc-tural design. The results underscore a notable correlation between dowel diameter and character-istic strength, with implications for engineering practices. Node placements significantly affect dowel-bearing capacity, while bamboo's physical attributes, including thickness, culm diameter, and moisture content, exhibit modest correlations with strength. The derived equation aims to assist in structural design, mitigating splitting and bearing failures in bamboo structures. This research establishes a foundation for optimizing the use of Bambusa blumeana in sustainable construction, advancing the understanding of its dowel-bearing strength for improved sustainability and resili-ence in the construction industry. Future research suggestions include exploring bamboo-mortar composites, additional node placements, and employing more comprehensive empirical equations and curve-fitting techniques. The study advocates for further investigations with more diverse and larger bamboo samples to bolster robustness. Additionally, delving into bamboo ductility may offer valuable insights.

Within this paper, electro-mechanical long-term tests on a thrust bearing are presented. The effects of an additional electrical load on the bearing raceways and the used lubricant are investigated. Chemical and rheological investigations are presented which show the changes in the lubricant. These investigations are compared with the electrical loads and the occurring raceway damage. In addition, a comparison is made with mechanical reference tests. This procedure makes it possible to classify the changes that occur due to the electrical load and to distinguish the effects from each other. The background to these investigations is the increased occurrence of parasitic currents in electric motors, which can lead to damage to machine elements. The phenomena that occur here are new challenges in the development of drive trains.

Abstract In order to reduce the failure accidents of conventional packers, a kind of sealing structure of retrievable packers is designed, which can provide reference for optimizing the sealing performance and pressure capacity of packers. And theoretical calculation and experimental research on its sealing performance and pressure capacity are carries out through the finite element analysis on the contact with large deformation based on Abaqus and experimental. The results show that when the rubber cylinder of retrievable packers in the sealing process, the upper packer is subjected to greater stress and mainly plays a sealing role. In order to improve the sealing performance of packer, the height of upper and lower packer should be preferentially selected about 60 mm, the height of middle rubber cylinders should be about 50 mm, and the thickness of packer should be about 21 mm. The newly designed rubber cylinders can meet 150 ℃. Sealing and pressure-bearing function under the condition of 10000 Psi. The rubber cylinder of newly designed can satisfy the function of sealing and pressure-bearing under 140 ℃ and 10000 Psi. The whole experiment shows that the capacity of bearing pressure and sealing is stable, which can better meet the requirements of field use.

In Africa, 80% of households in urban areas are food insecure and is coupled with a dramatically changing urban food culture towards increased consumption of sugary and fatty foods. Consequently, incidences of obesity and undernourishment in many African cities are becoming escalating. Urban and peri-urban forestry emerges as a complementary measure to contribute towards elimination of urban hunger and improved nutritional security. However, there is scanty knowledge about the composition, diversity and socioeconomic contributions of urban food trees in African cities and this hinders policy discussions integrating urban forestry into the food security discourse. This paper examines the diversity and composition of the urban forest and food trees of Accra and sheds light on perceptions of urbanites regarding food tree cultivation and availability in the city. Using a mixed methods approach, about 105 respondents in six neighbourhoods of Accra were interviewed while over 200 100-m2 plots were surveyed across five land use types. Twenty-two out of the 70 woody species in Accra are edible. The food tree abundance in the city is about half of the total number of trees enumerated. The species richness and abundance of the edible trees and all trees in the city were significantly different among land use types (p<0.0001) and neighbourhood types (p<0.0001). The diversity of food bearing tree species was much higher in the poorer neighbourhoods than in the wealthier neighbourhoods. Respondents in wealthier neighbourhoods indicated that tree and fruit tree cover of the city was generally low and showed greater interests in cultivating fruit trees and expanding urban forest cover than poorer neighbourhoods. These findings demonstrate the need for urban food policy reforms that integrate urban grown tree foods in the urban food system/culture.

Inflammation is an underlying problem for many disease states and has been implicated in iron deficiency (ID). This study aimed to determine whether iron status is improved by epigallocate-chin-3-gallate (EGCG) through reducing inflammation. Thirty-two male Sprague-Dawley rats were randomly divided into four groups (n = 8 each): positive controls, negative controls, lipo-polysaccharide (LPS, 0.5 mg/kg body weight), and LPS + EGCG (LPS plus 600 mg EGCG/kg diet). Iron status, hepcidin, C - reactive protein (CRP), serum amyloid A (SAA), and interleukin-6 (IL-6) were measured. There were no differences in treatment groups compared with control in CRP, hepcidin, and liver iron concentrations. Serum iron concentrations were significantly lower in the LPS (p=0.02) and the LPS+EGCG (p=0.01) than in the positive control group. Compared to the positive control group, spleen iron concentrations were significantly lower in the negative con-trol (p<0.001) but not with both LPS groups. SAA concentrations were significantly lower in LPS + EGCG group compared to LPS alone group. IL-6 concentrations were significantly higher in LPS+EGCG (p= 0.004) than in any of the three groups. EGCG reduced SAA concentrations but did not affect hepcidin or improve serum iron concentration or other iron markers.

Dietary iron assimilation is critical for health and essential to prevent iron deficient states and related comorbidities, such as anemia. The bioavailability of iron is limited, while its absorption and metabolism are tightly controlled to keep body iron stores within a relatively narrow range. Genetic inactivation of the iron hormone hepcidin causes hereditary hemochromatosis, an endocrine disorder of iron overload characterized by chronic hyperabsorption of dietary iron, with deleterious clinical complications if untreated. The impact of high dietary iron intake and elevated body iron stores in the general population is not well understood. Herein, we summarize epidemiological data suggesting that high intake of heme iron, which is abundant in meat products, poses a risk factor for metabolic syndrome pathologies, cardiovascular diseases, and some cancers. We discuss clinical relevance and potential limitations of data from cohort studies, as well as the need to establish causality and elucidate molecular mechanisms.

Background: Ankle fractures, comprising about 10% of musculoskeletal injuries, pose a significant healthcare burden with an increasing incidence, particularly among an aging population. This study focuses on isolated Danis-Weber type B fractures. Recent trends lean towards surgical intervention for anatomical restoration, quicker recovery, albeit with associated complications. This report aims to assess the safety and efficacy of NewClip narrow locking plate system with early weight bearing in treating isolated fibular fractures. Methods: The study includes patients with Danis-Weber type B fractures surgically treated with NewClip narrow locking plate system. Exclusions involved nondisplaced fractures, open fractures, or those requiring additional fixation.Results: Fifteen patients were enrolled in this study. Minor complications, including wound swelling, were observed in two cases. The Visual Analogue Scale (VAS) for pain exhibited a steady decline postoperatively, with almost complete resolution by the third month. At three months, the FAOS demonstrated excellent results, and final follow-up at twelve months revealed complete osseous healing without complications.Conclusions: The use of this type of plates in treating isolated fibular fractures with early weight bearing shows promising results in terms of fracture healing, pain resolution, and functional outcomes warranting further investigation with larger cohorts.

There are two basic methods for radial external load distribution calculation on rolling elements in a rolling element bearing: the discrete method and the integral method. Solving the discrete equilibrium quasi-static equation using the Newton-Raphson scheme, more accurate results are derived than those based on the integral method, with small theoretical and computational efforts. The Sjövall’s radial integral factors, as well as some approximations proposed in the literature, for line- and point-contacts, are revisited. Numerical approximations for the Sjövall's radial integrals are proposed. The approximations’ errors with respect to the Sjövall’s radial integral’s numerical integration are shown. The numerical results of the displacement between inner and outer rigid rings, maximum hertzian contact deflection and the most loaded element load are shown for some ball and roller bearings, for radial external load ranging from 0 to 10,000 N, and for positive, negative and zero radial clearance, solving the discrete equilibrium quasi-static equation using the Newton-Raphson method. A total of 16 figures is shown in this work, many of which are made up of sub-figures. A total of 58 figures and sub-figures is shown.

: Clay covers a substantial portion of the Earth. Such soil covers Iraq’s central and southern regions, where the depth of the clay may reach 150 m. All enhancement techniques and methods for transporting large loads cease to function or become prohibitively expensive in such soils. In this case, thermal treatment is the most effective method. In this study, a novel heating system was created and produced utilizing gas as the heat source via boreholes that simulate reality. The borehole heating cases were planted inside soft clay soil to enhance the soil. Different parameters were investigated, including the spacing between boreholes (3, 4, and 5 times the outer diameter of the borehole), the heating depth (1, 1.5, 2, and 2.5 times the width of the model footing), the duration of heating (2, 4, 6, 8, and 10 hrs), and the pattern (square, circular, triangular). The results showed the strength and behavior of the soil treated with heated boreholes at varying spacings, depths, patterns, and heating periods. The best results were found for a spacing, depth, and heating time of three times the outer diameter of the borehole, two times the width of the footing model, and eight hours, respectively. The effect of the heated borehole casing pattern was small when the heated borehole casing was used. The experiments conducted on heated soil showed that the undrained shear strength (Cu) increased from 14 to 360 kPa and then dropped to 140 kPa (as an average with depth). In contrast, the average angle of internal friction (Ø) rose from 0 to 52 degrees and decreased to 16 degrees (as an average with depth) from the center of the heating model to the furthest point affected by heating. In addition, the EDS pattern showed that components like silicon, aluminum, and iron dropped at 300 °C and rose at 400 °C in the treated soils. At 200 °C, the calcium content rose, and then dropped dramatically at 400 °C. The carbon percentage increased at 300 °C and decreased at 400 °C. The elements’ proportions showed little change or remained stable at temperatures between 400 °C and 600 °C.

Clinching is a manufacturing method of mechanical joining two or more materials without the use of heat or additional components. This process relies on high plastic deformation to create a secure bond. Clinching technology is widely used for joining various grades and thickness of materials. Especially in the automotive industry, clinching is an alternative to spot resistance welding. However, the load-bearing capacity of clinched joints is comparatively lower when compared to resistance spot welded joints. This research aimed to enhance the load-carrying capacity of clinched joints. Experimental tests were conducted on clinched joints with locally modified microstructures to optimize their placement within the joint. The microstructure distribution in the clinched joint region was analysed using light and scanning electron microscopy, as well as microhardness measurements. Two material grades, micro-alloyed steels HX420LAD+Z and dual-phase ferritic-martensitic steels HCT600X+Z, were tested. Each grade underwent five groups of ten samples, subject to identical experimental conditions of local heating by resistance spot welding (RSW) and clinching. The application of RSW to the clinched joint area resulted in increase of load-bearing capacity for both joined types of materials.

This article discusses the issue of hardened steel machining. Many components in the engineering industry use hardening as the final heat treatment. These components usually occupy a significant position in a given assembly unit. They guarantee the correct operation of the entire technical equipment in total cooperation with other components. The quality of these components depends on the integrity of their surface. The production of these parts is usually carried out by traditional technological procedures. An example of such a technology is clearly grinding. However, this article discusses the application of other finishing technologies using tool material made of cubic boron nitride (CBN). The technology used is finishing turning with subsequent tumbling technology. The subject of the evaluation is the integrity of the surface. In this part of the experiments, there are mainly individual parameters of surface roughness. Compared components are bearing rings, in this case the inner surface of the housing ring.

Reinforced concrete (RC) columns are often placed under confinement to increase their strength and ductility. Carbon fiber reinforced polymer (CFRP) materials have recently been recognized as favorable confinement systems. At present, a number of national standards and codes dedicated to the design of concrete components strengthened with CFRP in general and CFRP confinement in particular are available. These sets of rules provide design equations for confined reinforced concrete columns with circular and rectangular cross sections. Most of the standards and codes exhibit significant differences, including the used predictive models limitations, observed effects, and covered loading conditions. In this paper, five international standards and design guidelines are introduced and discussed. The purpose is to present a constructive and critical assessment of the state-of-the-art design methodologies available for CFRP confined RC columns and to discuss effects not previously considered properly. Therefore, some recent research efforts and findings from the Leipzig University of Applied Sciences are also introduced. The obtained data is used for a comparative study of the guideline predictive equations. Furthermore, it is shown that some new findings concerning the rupture strength and the maximum strength plus accompanying axial strain of a CFRP confined column are suitable to improve the current guidelines.

Myelodysplastic syndromes and myeloproliferative neoplasms both represent hematologic diseases associated with bone marrow failure often resulting in anemia. For those patients, transfusion of red blood cell (RBC) units is essential, but results in iron overload (IOL) that may affect various organ functions. Therefore, iron chelation therapy plays a major role in anemic patients, not only because it reduces IOL, but also because it may improve hematopoietic function by increasing hemoglobin or diminishing requirement of RBC transfusions. To assess the utility, efficacy and safety of the different iron chelation medication approved in Germany as well as to examine the effect of chelation on hematopoietic insufficiency, a prospective, multicenter, non-interventional study named EXCALIBUR was designed. In total, 502 patients from 106 German hospitals and medical practices were enrolled. A large proportion of patients switched from deferasirox dispersible tablet to deferasirox film-coated tablet, mainly due to more convenient application which was reflected in the treatment satisfaction questionnaire for medication scores. Iron chelation was effective in lowering serum ferritin levels, with the observed adverse drug reactions being in line with the known safety profile. Hematologic response occurred in a few patients, comparable to other studies that examined hematologic improvement in patients with MDS.

The study, conducted at the Department of Medicine, Maulana Azad Medical College and associated Lok Nayak Hospital, aimed to investigate the prevalence of iron deficiency anaemia among anaemic overweight and obese individuals. Fifty participants were included after screening and consent, undergoing socio-demographic assessment, clinical evaluation, and laboratory investigations. Middle to old-aged individuals predominated (Mean ± SD: 54.54 ± 11.32 years), with females comprising 62%. All subjects were obese (mean BMI: 37.27 ± 5.71 kg/m²), with common comorbidities including hypertension (68%), diabetes (36%), and obstructive sleep apnea-hypopnea syndrome (32%). Nutritional deficiencies, particularly iron deficiency, were prevalent, affecting 62% of subjects, with 48% having iron deficiency alone. Anemia of chronic illness was observed in 38%. Laboratory parameters showed low hemoglobin (8.53 ± 1.23 g/dL), MCV (78.75 ± 10.13 fL), and elevated ESR (20.56 ± 21.47 mm/hour) and CRP levels (4.71 ± 3.32 mg/dL), indicating inflammation. Correlation analyses revealed negative associations between BMI and serum iron/ferritin and positive associations with serum hepcidin. The study underscores the significance of addressing nutritional deficiencies and monitoring iron status in obese populations, suggesting potential associations between obesity and iron metabolism. Further research is needed to explore these relationships for clinical management implications.

Oligodendroglioma (OG) is a brain tumor that contributes to < 1% of brain tumor diagnoses in the pediatric population. Unfortunately, pediatric OG remains without definitive molecular characteristics to aid in diagnosis, and little is known about the tumor microenvironment. Tumor cells' metabolism and proliferation rate are generally higher than healthy cells, so their iron demand is also significantly increased. This consideration underlines the great importance of iron for tumor development and progression. In this context, this study aims to evaluate the effect of iron in a cellular in vitro model of human oligodendroglioma brain tumor. Cell morphology, the effect of siderotic medium on cell growth, iron uptake, and the expression of iron metabolism-related genes were evaluated by optic microscopy, ICP-MS, confocal microscopy, and RealTime PCR, respectively. This study underlines the great importance of iron for tumor development and progression, but also the possibility of reducing the available iron concentration to determine an antiproliferative effect on OGs. Therefore, every attempt can be promising to defeat the OGs for which there are currently no long-term curative therapies.

Baía de Todos os Santos is the second largest bay in Brazil and is home to important ecosystems, including estuarine systems and mangroves. However, studies on the seasonal variability of its soil properties and composition are still scarce. For this study, soil and leaf samples were seasonally collected from mangrove forests at four sites (Cacha Prego, Ponta Grossa, Ilha de Maré, and Pitinga), which are representative of different environmental conditions within the BTS. Soil physicochemical properties, soil composition and partition of Fe forms were determined, and analysis of minerals by Scanning Electron Microscope, was performed on soil samples. Isotopic ratios (δ13C, δ15N) were also determined on soil and leaf samples. Soils showed significant spatial and temporal changes affecting both their properties (pH, Eh) and their composition (TOC, pyrite and Fe oxyhydroxide contents). Clear spatial changes were observed in redox potential, significantly affecting the concentrations of the different geochemical forms of Fe, particularly the concentrations of crystalline oxyhydroxydes and pyrite in one of the studied sites. In three of the study sites, pyrite crystals showed clear evidence of degradation associated with sandy soils. Finally, δ13C and N/C ratios in soils seem to suggest a mixed origin of organic matter.

Beta-thalassemia major (β-TM) is a severe form of thalassemia caused by mutations in the β-globin gene, resulting in partial or complete deficiency of β-globin chains. This deficiency results in oxidative stress, dyserythropoiesis, and chronic anemia. Cytokine dependent hematopoietic cell linker (CLNK) belongs to the adaptor protein family and has the capacity to interact with multiple signaling proteins thereby modulating signal transduction. The aim of the present study was to examine CLNK in sera of β-TM patients and examine its association with iron overload biomarkers. Sixty β-TM patients, aged 3–12 years old and undergoing blood transfusions, and 30 healthy control children were recruited and CLNK, ferritin and iron status parameters were measured. The results showed a significant increase (p < 0.001) in serum CLNK levels in β-TM patients as compared with normal controls. The increased levels of CLNK were significantly associated with increased ferritin levels. Increased CLNK levels in β-TM may be explained by reciprocal effects between immune signaling and immature erythrocytes, which, release soluble receptors and signaling molecules, including CLNK, in the blood.

Ghrelin and obestatin, two antagonist peptide hormones, are purportedly involved in stimulating appetite and controlling energy balance in humans. Serum ghrelin level is also associated with iron deficiency anemia (IDA), but no study has yet been made of the obestatin level in patients with IDA, even though both hormones are a single gene product. Therefore, the purpose of this investigation is to see whether there is a link between IDA and these two hormones among other hematological parameters in patients with IDA. To measure ghrelin and obestatin, human saliva and serum were collected from 30 women with IDA, aged 31.7 ± 10.7 years, and 30 control women, aged 30.2 ± 8.0 years, with repeated collection of samples over a period of 1 week and 1 month. Saliva and serum ghrelin levels were measured by ELISA. Serum hemoglobin, ferritin, hematocrit and total iron-binding capacity (TIBC) values were determined with an Olympus AU2700. Saliva and serum ghrelin and obestatin levels were significantly lower in the IDA group compared with controls; these levels increased slightly above baseline with iron treatment, but remained below the control values. Furthermore, and as expected, serum hemoglobin, ferritin, and hematocrit levels were significantly increased with iron treatment, while total iron-binding capacity decreased compared to baseline concentrations. The findings suggest that IDA might be linked to imbalance of circulating (serum) and non-circulating (saliva) ghrelin and obestatin levels. Decreased ghrelin and obestatin might destroy iron homeostasis through its effect on intestinal absorption. Measuring these hormone levels might be useful for monitoring the response to iron treatment. Also, serum and saliva levels for both hormones were well correlated. Thus, using saliva in place of serum for monitoring the two hormones should minimize inconvenience and patient discomfort.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

Improper design of friction pendulum bearings can lead to poor seismic reduction performance and may result in the failure of local vulnerable components. And the parameter design of friction pendulum bearings mainly relies on experience and verification calculations at present. This paper proposes an adaptive genetic algorithm considering the overall evolution state of the population, adjusting crossover and mutation probabilities adaptively based on individual fitness and population diversity. Compared to traditional algorithms, it exhibits better global search capabilities and convergence efficiency. Combining the improved genetic algorithm with finite element models, a parameter optimization method is proposed. The parameters of friction pendulum bearings are optimized, providing reference for the design of seismic isolation devices.

The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

A frequent problem in Geotechnics is the soils with inadequate physical-mechanical properties before the efforts to which they will be subjected by the constructions, incurring cost overruns caused by their engineering improvement. The need to improve the engineering properties of soils is not recent, currently observing that the most common alternatives are binders such as cement and lime. The climate change observed in recent decades and the uncontrolled emission of greenhouse gases have motivated Geotechnical and Geoenvironmental researchers to seek mechanisms for soil reinforcement from a more sustainable and environmentally friendly approach by proposing the use of recycled and waste materials. An alternative is natural fibers, which can be obtained as waste from many agro-industrial processes, implying their high availability and low cost. Sawdust as a by-product of wood processing has a rough texture that can generate high friction between the fiber and the matrix of the soils, leading to a significant increase in its shearing strength and bearing capacity. This concept of improving the properties of soils using natural fibers distributed randomly is inspired by the natural phenomenon of grass and/or plants that when growing on a slope can effectively stabilize a said slope.

Wear usually occurs in the loaded part of hydrodynamic bearings and leads the bearing geometry imperfections. This paper investigates the effects of wear-induced geometric imperfections of tilting pad journal bearings (TPJBs) on the dynamic behavior of the system. Furthermore, the effect of wear on the journal-bearing rub-induced contact pressure severity is investigated. A novel tribo-dynamic model is proposed for a flexible rotor-worn TPJB which integrates a mixed elastohydrodynamic model with a rotor-worn TPJB thermal and dynamic model to assess the effects of the bearing wear progression on the rotor-TPJB behavior. Based on the results, wear changes the temperature distribution of the pads and oil film as well as the dynamic behavior of the system. Dynamic simulations reveal a higher vibration level and contact pressure for the worn TPJBs near the system's critical speed and service speed. Finally, thermal and dynamic condition indicators are suggested to detect TPJB wear severity at its early stages.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

The purpose of feature selection is to find important features from the original high-dimensional space. As atypical feature selection algorithm, Locally linear embedding(LLE)-based feature selection algorithm, which applies the idea of LLE to the graph-preserving feature selection framework, has been received wide attention. However, LLE-based feature selection framework is sensitive to noise and K-nearest neighbors. To address these problems, an improved LLE-based feature selection algorithm, robust LLE (RLLE) vote, is proposed. In this algorithm, $l_1$ and $l_2$ regularization are introduced into the high-dimensional reconstruction model of LLE. Furthermore, RLLE vote also proposes a criterion to measure the difference between the reconstruction features and the original features, and then the importance features can be selected by this criteria. Extensive experiments are carried out on a benchmark fault data set and the bearing data set collected from our own laboratory, and the experimental results demonstrate that RLLE vote achieves the most significant performance compared existing state-of-art methods.

The use of new developed high-strength steel in concrete members can reduce steel bars congestion and construction costs. This research aims to study the behavior of concrete columns reinforced with new developed high-strength steel under eccentric loading. Ten reinforced concrete columns were fabricated and tested. The test variables are transverse reinforcement amount and yield strength, eccentricity, and longitudinal reinforcement yield strength. The failure patterns are compression and tensile failure for columns subjected to small eccentricity and large eccentricity, respectively. The same level of post-peak deformability and ductility only can be obtained with lower amount of transverse reinforcement when high-strength transverse reinforcements are used in columns subjected to small eccentricity. The high-strength longitudinal reinforcement can improve bearing capacity and post-peak deformability of concrete columns. Besides, three different equivalent rectangular stress block (ERSB) parameters in predicting bearing capacity of columns with high-strength steel were discussed based on test and simulated results. It is concluded that the Code of GB 50010-2010 overestimates the bearing capacity of columns with high-strength steel, whereas bearing capacities computed using Codes of ACI 318-14 and CSA A23.3-04 agree well with test results.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

Many drastic actions are taken by cocaine users for the sake of experiencing high dopamine levels, which depends on iron for its synthesis. Dopamine depletion and iron deficiency are also involved in the symptoms of restless leg syndrome (RLS). The intersecting biochemical pathways of cocaine use, iron deficiency, and RLS have not been adequately investigated. This case report reveals the successful treatment of a patient with these conditions. A 63-year-old male with a history of cocaine use disorder, insomnia, and RLS sought emergency care for suicidality. Upon admission, he was also found to be iron-deficient. He revealed that his RLS worsened when he attempted to abstain from cocaine. He also used alcohol to sustain the effects of cocaine when the cost of cocaine was too high. During hospitalization, his mood, cravings, and RLS were resolved with adjunctive iron supplementation as well as 300 mg of Wellbutrin. If iron-deficient, replenishment of adequate dopaminergic receptor density and function via supplementation may play an essential role in the prevention of cocaine use and cessation of cocaine withdrawal. Further research is warranted to validate these findings and understand the implications of iron supplementation in addiction medicine.

Iron deficiency anemia (IDA) is a world health problem for humans and other mammals; affecting critical stages of development. Pigs have been used as an experimental model for the study and prevention of anemia because of physiological and metabolic similarities with humans. Iron dextran particles (IDP) are used for intramuscular (IM) IDA treatments in pigs, but are insufficient for prevention of anemia due to quick metabolization. Therefore, the objective of this study was to develop chitosan thermosensitive hydrogels (CTH) formulations and to study their potential as a mammalian parenteral iron dextran supplementation strategy. CTH were loaded with IDP at increasing iron concentrations (0.1, 0.2 and 0.4 g of theorical iron/g of chitosan) and characterized as an IM iron supplement. All the CTH-IDP formulations were thermosensitive and can be injected IM at ~4 °C, with a significant rise in viscosity between 25-37 °C. IDP content was physically trapped in the chitosan hydrophobic gel at 37 °C, without evidence of chemical bonding. We conclude that CTHs are a promising strategy for IM delivery strategy of IDP, and these results may be useful for future iron supplementation studies in pigs, humans and other mammals.

Neurodegeneration with brain iron accumulation (NBIA) is a group of rare neurogenetic dis-orders frequently associated with iron accumulation in the basal nuclei of the brain. Among NBIA subtypes, β -propeller protein-associated neurodegeneration (BPAN) is associated with mutations in the autophagy gene WDR45. The aim of this study was to demonstrate autophagic defects and secondary pathological con-sequences in cellular models derived from two patient harboring WDR45 mutations. Both protein and mRNA expression levels of WDR45 were decreased in patient-derived fibro-blasts. In addition, the increase of LC3B upon treatments with autophagy inducers or inhibitors was lower in mutant cells compared to control cells, suggesting decreased autophagosome formation and impaired autophagic flux. Transmission electron microscopy (TEM) analysis showed mitochondrial vacuolization associated with accumulation of lipofuscin-like aggregates containing undegraded material. Autophagy dysregulation was also associated with iron ac-cumulation and lipid peroxidation. In addition, mutant fibroblasts showed altered mitochon-drial bioenergetics. Antioxidants such as pantothenate, vitamin E and α-lipoic prevented lipid peroxidation and iron accumulation. However, antioxidants were not able to correct the ex-pression levels of WDR45 neither the autophagy defect nor cell bioenergetics. Our study demonstrated that WDR45 mutations in BPAN cellular models impaired autophagy, iron metabolism and cell bioenergetics. Antioxidant partially improved cell physiopathology, however autophagy and cell bioenergetics remained affected.

Wheat (Triticum aestivum L.) being a staple food crop is an important nutritional source providing protein and minerals. It is important to fortify staple cereals like wheat with essential minerals to overcome the problems associated with malnutrition. The experiment was designed to evaluate the status of 11 micronutrients including grain iron (GFe) and zinc (GZn) in 62 wheat cultivars released between 1911 and 2016 in Pakistan. Field trials were conducted over two years and GFe and GZn were quantified by both inductively coupled plasma optical emission spectroscopy (ICP-OES) and energy dispersive X-ray fluorescence spectrophotometer (EDXRF). The GZn ranged from 18.4 to 40.8 mg/kg by ED-XRF and 23.7 to 38.8 mg/kg by ICP-OES. Similarly, GFe ranged from 24.8 to 44.1 mg/kg by ICP-OES and 26.8 to 36.6 mg/kg by EDEXR. The coefficient of correlation was higher for GZn (r=0.90), compared to GFe (r=0.68). Modern cultivars like Zincol-16 and AAS-2011 showed higher GFe and GZn along with improved yield components. Old wheat cultivars WL-711, C-518 and Pothowar-70 released before 1970 also exhibited higher value of GFe and GZn, however their agronomic performance was poor. Multivariate analysis using ten micronutrients (Al, Ca, Cu, K, Mg, Mn, Na and P) along with agronomic traits, and genome-wide SNP markers identified the potential cultivar with improved yield, biofortification trait and wider genetic diversity. Genetic gain analysis identified significant increase in grain yield (0.4% year-1), while there was negative gain for GFe (-0.11% year-1) and GZn (-0.15% year-1) over the span of 100 years. The Green Revolution Rht-B1 and Rht-D1 genes had strong association with plant height, and grain yield (GY), while semi-dwarfing alleles had negative effect on GFe and GZn contents. This study provided a valuable insight into biofortification status of wheat cultivars deployed historically in Pakistan and is a valuable source to initiate a breeding strategy for simultaneous improvement in wheat phenology and biofortification.

Iron (Fe) is a trace element that plays essential roles in various biological processes such as DNA synthesis and repair, as well as cellular energy production, or oxygen transport, and it is currently widely recognized that iron homeostasis is dysregulated in many cancers. Indeed, several iron homeostasis proteins may be responsible for malignant tumor initiation, proliferation, and for metastatic spread of tumors. A large number of studies demonstrated the potential clinical value of turning these deregulated proteins as prognostic and/or predictive biomarkers of malignancy and /or response to anticancer treatments. Additionally, the iron addiction of cancer cells and the importance of iron in ferroptosis cell death signaling pathways prompted the development of therapeutic strategies against advanced stage or resistant cancers. In this review, we selected relevant and promising studies in the field of iron metabolism in cancer research and clinical oncology. Besides, we discuss some co-existing discrepant findings. We will also present and discuss the latest lines of research related to targeting iron, or its regulatory pathways, as potential promising anti-cancer strategies for human therapy. Iron chelators, such as deferoxamine or iron-oxide based nanoparticles, which are already tested in clinical trials, alone or in combination with chemotherapy will also be reported.

Background: Essential hypertension is a major public health associated with increase pressure on the vascular walls and red blood cells (RBCs). In the present work, osmotic fragility (OF) of RBCs was reexamined in the means of its correlation with two risk factor; iron status and lipid profile. Experimental: OF, iron status parameters, and lipid profile components were measured in 60 patients and compared with the results of 30 controls. Results: The results showed a significant increase in all iron indices of hypertensive patients in comparing with healthy control group except TIBC, UIBC, and transferrin concentrations, which decrease in these patients in comparing with control group. Serum TGs, total cholesterol, VLDLc, and LDLc were increased while there is no significant in serum HDLc in patients to comparing with control group. There is no significant change in OF between patients and controls where p=0.173. The iron status parameters and lipid profile components were dependent on sex and smoking state. Hemoglobin and PCV were correlated significantly with total cholesterol and LDLc. Transferrin saturation showed a positive correlation with cholesterol, LDLc, and TGs, but negatively correlated with HDL_c. No significant correlation between all the measured parameters and OF in HT patients. There is a significant correlation between serum ferritin and systolic BP and between Hb and systolic BP. Conclusion: No significant effect on the OF in HT patients. HT patients have elevated level of iron parameters in comparing with controls. OD has no correlation with iron status parameters or with lipid profile components.

Iron deficiency in the fetal and neonatal period (perinatal iron deficiency) bodes poorly to neuro-development. Given its common occurrence and the negative impact on brain development, a screening and treatment strategy that is focused on optimizing brain development in perinatal iron deficiency is necessary. Pediatric societies currently recommend a universal iron supple-mentation strategy for full-term and preterm infants that does not consider individual variation in the body iron status and could lead to under-treatment or over-treatment. Moreover, the focus is on hematological normalcy and not optimal brain development. Several serum iron indices and hematological parameters in the perinatal period are associated with risk of abnormal neurodevelopment, suggesting their potential use as biomarkers for screening and monitoring treatment in infants at risk for perinatal iron deficiency. A biomarker-based screening and treatment strategy that is focused on optimizing brain development will likely improve outcome in perinatal iron deficiency.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Sideroflexins (SLC56 family) are highly conserved multi-spanning transmembrane proteins inserted in the inner mitochondrial membrane in eukaryotes. Few data are available on their molecular function but, since their first description, they were thought to be metabolite transporters probably required for iron utilization inside the mitochondrion. Such as numerous mitochondrial transporters, sideroflexins remain poorly characterized. The prototypic member SFXN1 has been recently identified as the previously unknown mitochondrial transporter of serine. Nevertheless, pending questions on the molecular function of sideroflexins remain unsolved, especially their link with iron metabolism. Here, we review the current knowledge on sideroflexins, their presumed mitochondrial functions and the sparse - but growing - evidence linking sideroflexins to iron homeostasis and iron-sulfur cluster biogenesis. Since an imbalance in iron homeostasis can be detrimental at the cellular and organismal levels, we also investigate the relationship between sideroflexins, iron and physiological disorders. Investigating Sideroflexins’ functions constitutes an emerging research field of great interest and will certainly lead to main discoveries on mitochondrial physiopathology.

The study of co-fusion was one of the essential topics in the history of metallurgy in China. Simulation experiments had been an essential concept in the study of the co-fusion steelmaking process. This paper mainly studied the simulation experiments of co-fusion from two aspects: the replication of co-fusion swords by three different methods, and the micro-analysis of the co-fusion samples. The experimental results indicated that several co-fusion swords could be made by different processes, but the carbon content and surface hardness were quite different. During repeated forging welded, the microstructure of the samples transformed from laminated to homogenized, finally the steel with a uniform carbon content was obtained. It was challenging to find the characteristics of co-fusion from the homogenized samples. The results prompted people to rethink the microstructure characteristics of ancient co-fusion artifacts.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

Alum sludge is a byproduct of water treatment plants and its use as a soil stabilizer has gained increasing attention due to its economic and environmental benefits. Its application has been shown to improve the strength and stability of soil, making it suitable for various engineering applications. However, to go beyond just measuring the effects of alum sludge as a soil stabilizer, this paper explores the use of artificial intelligence (AI) methods to predict the California bearing ratio (CBR) of soils stabilized with alum sludge. Three AI methods, including two black box methods (artificial neural network and support vector machines) and one grey box method (genetic programming), were used to predict CBR based on a database with nine input parameters. The results showed that all three AI models were able to predict CBR with good accuracy, with coefficient of determination (R2) values ranging from 0.94 to 0.99 and mean absolute error (MAE) values ranging from 0.30 to 0.51. In a novel approach, the genetic programming method was used to produce an equation to estimate CBR, which included seven inputs and accurately predicted CBR. The analysis of sensitivity and importance of parameters showed that the number of hammer blows for compaction was the most important parameter, while the parameters for maximum dry density of soil and mixture were the least important. This study suggests that AI methods can effectively predict the performance of alum sludge as a soil stabilizer, and the proposed equation using genetic programming can be a useful tool for predicting CBR.

To prolong the fatigue life of a product handled by machine, parametric accelerated life testing (ALT) is mentioned as an organized technique to pinpoint design flaws and minimize fatigue-connected failures. It requires (1) an ALT procedure, (2) fatigue model, (3) parametric ALTs with adjustment, and (4) an approximate of whether present product complete the BX life. The use of a quantum-transported time-to-failure archetype and a sample size are advised. The improvements in the reliability of a refrigerator ice-maker, comprising an auger motor with bearing, were utilized as a case investigation. In the 1st ALT, a steel rolling bearing cracked due to repeated loads under cold circumstances (below −20 C) in the freezer compartment. The bearing was altered by adjusting the matter from AISI 52100 alloy steel with 1.30-1.60% chromium to lubricated sliding bearing with sintered and hardened steel (FLC 4608-110HT) because of its high fatigue strength at lower temperatures. In the 2nd ALT, a helix made of polycarbonates (PCs) fractured. As an adjustment, a reinforced rib of the helix was thickened. As no troubles in the 3rd ALT occur, the lifetime of an ice-maker was proved to be B1 life 10 years.

In recent years, intelligent fault diagnosis algorithms using deep learning method have achieved much success. However, the signals collected by sensors contain a lot of noise, which will have a great impact on the accuracy of the diagnostic model. To address this problem, we propose a one-dimensional convolutional neural network with multi-scale kernels (MSK-1DCNN) and apply this method to bearing fault diagnosis. We use a multi-scale convolution structure to extract different fault features in the original signal, and use the ELU activation function instead of the ReLU function in the multi-scale convolution structure to improve the anti-noise ability of MSK-1DCNN; then we use the training set with pepper noise to train the network to suppress overfitting. We use the Western Reserve University bearing data to verify the effectiveness of the algorithm and compare it with other fault diagnosis algorithms. Experimental results show that the improvements we proposed have effectively improved the diagnosis performers of MSK-1DCNN under strong noise and the diagnosis accuracy is higher than other comparison algorithms.

Nitride and carbide are the second phases which play an important role in the performance of bearing steel, and their precipitation behavior is complicated. In this study, TiN-MC_x precipitations in GCr15 bearing steels were obtained by non-aqueous electrolysis, and their precipitation mechanisms were studied. TiN is the effective heterogeneous nucleation site for Fe₇C₃ and Fe₃C, therefore, MC_x can precipitate on the surface of TiN easily, its chemistry component consists of M₃C and M₇C₃ (M = Fe, Cr, Mn) and Cr₃C₂. TiN-MC_x with high TiN volume fraction, TiN forms in early stage of solidification, and MC_x precipitates on TiN surface after TiN engulfed by the solidification advancing front. TiN-MC_x with low TiN volume fraction, TiN and MC_x form in late stage of solidification, TiN can not grow sufficiently and is covered by a large number of precipitated MC_x particles.

The vibration signal of the engine contains strong background noise and many kinds of modulating components, which is difficult to diagnose. Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). VMD can effectively avoid endpoint effect and modal aliasing. However, VMD cannot effectively eliminate the random noise in the signal, so the random decrement technique is introduced to solve the problem. Based on the crankshaft bearing fault simulation experiment, the four kinds of wear state vibration signals are decomposed by VMD, and the modal components with smaller permutation entropy are selected as fault components. Then the fault component is processed by the random decrement technique, and the Hilbert envelope spectrum of the fault component is obtained. Compared with the fault feature extraction method based on EMD and EEMD, the feature extraction results of the proposed method are better than those of the above two methods. The simulation analysis and the simulation test of the crankshaft bearing fault verify the effectiveness of the proposed method.

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in term of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity because of both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

Iron (Fe) deficiency specifically is the most common nutritional disorder due to insufficient absorbable Fe. Biofortification is a process of enriching the nutrient content of staple crops and is considered as a sustainable and cost-effective strategy to address micronutrient deficiency problems especially in the less developed countries. Chickpea (Cicer arietinum L.) is a staple food in many developing countries worldwide and is an excellent source of micronutrients. Biofortification of chickpea is a possible solution to address Fe deficiency problem. Chickpea biofortification experiment was conducted under field conditions to evaluate the effects of different doses of Fe fertilizer (0 kg ha-1,10 kg ha-1 and 30 kg ha-1 of Fe-EDDHA) on Fe content in seeds of 18 chickpea cultivars. The experiment was designed as a factorial combination of 18 chickpea cultivars and 3 different doses in a randomized complete block design with 4 replications at two locations in Saskatchewan in 2015 and 2016. Fe concentration in seeds across 18 different chickpea cultivars increased with Fe fertilization. Fe concentration in X05TH20-2 and CDC Frontier cultivars increased from 57 ppm to 59 ppm and 56 ppm to 58 ppm, respectively, after adding Fe fertilizer in both location in 2015 and 2016.

The aim of the study was to investigate the association between maternal dietary iron intake during pregnancy and the gut microbiota characteristics of both the mother and neonate in a well-characterized cohort. A total of 95 mother-neonate dyads were included in our study, with basic information collected through questionnaires. A semi-quantitative Food Frequency Questionnaire (FFQ) was used to assess maternal dietary intake during pregnancy, and maternal dietary iron intake was categorized into &lt;20 mg/d and ≥20 mg/d groups. Fecal samples were collected from the mother in the third trimester and the neonate, allowing for assessment of the community profile and diversity of gut microbiota via 16S rRNA amplicon sequencing. Then, a comparison between different maternal dietary iron intake groups was conducted, adjusting for delivery mode (VD, vaginal delivery; CS, cesarean section) and other potential confounding factors. No significant differences in community profile and diversity were observed for the maternal gut microbiota in different dietary iron intake groups. In neonate fecal samples, the Shannon (P = 0.044) and Simpson (P = 0.010) diversity indices of the gut microbiota were higher in the maternal dietary iron intake ≥20 mg/d group, while Simpson diversity presented the same tendency in vaginal delivery (P = 0.041) after stratification. The relative abundance of the core genus Bifidobacterium showed a significant difference between groups (4.69 [1.19–12.77] vs. 13.98 [3.44–27.28]; P = 0.044). The abundance of Lactobacillus was different in the ≥20 mg/d group under both delivery modes (VD: beta = 2.9, w = 4.13; CS: beta = 2.77, w = 3.8). Our findings suggest that adequate dietary iron intake during pregnancy may promote beneficial bacterial colonization and increase the biodiversity of the neonate gut microbiota.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

Keywords: iron deficiency anemia; IDA; anemia; knowledge; awareness.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

INTRODUCTION. The most common cause of eating non-food items (pica) is specific deficiencies of minerals, such as iron. This study aimed to assess the relationship between Pica and Iron deficiency anemia among pregnant women. METHODS. The study was conducted in the out-patient department, antenatal Clinic at East Jeddah Hospital from July to September 2020. Design: A quantitative descriptive correlation design. Sample size: A total of 400 pregnant women, included anemic pregnant women, ≥ 18 years old, with singleton fetus and iron deficiency anemia. RESULTS. The mean age was 32.2 ± 6.6, half of the participants reported food cravings. Ice was the main item in pica followed by clay and chalk. Two-thirds had pica, more than half during the 1st trimester. There is a statistically significant relationship between pica and the history of a family member, parity, and gravidity at (P< 0,001, P <0,001, P <0,005) respectively. Hb and hematocrit in relation to pica reflected a statistically significant relationship (P< 0,001) and (P< 0,001), respectively. The symptoms attributed to iron deficiency were significantly associated with pica (P< 0,006). CONCLUSION. The pica and iron deficiency anemia had a significant association with pregnant women in EJH. RECOMMENDATION. The follow-up visits should integrate the food behavior inquiry to check if the pica existing with anemic or non-anemic pregnant women. Also, increase the awareness among midwives-nurses about the prevalence of pica and iron deficiency anemia among pregnant women.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

Beta thalassemia major (β-TM) disorder characterized by the lack, or severe reduction in the production of hemoglobin β-globin chains. The standard protocol for the management of β-TM is blood transfusion and iron chelation therapy to reduce the iron overload state. The present study aimed to investigate the relationships between two iron regulatory hormones, hepcidin (HEPC) and erythroferrone (ERFE) levels and iron status parameters (ISPs) in Iraqi patients with β-TM. ISPs and hormones were measured in sixty patients and compared with thirty healthy controls. The results indicated significant changes in different iron status parameters, while ferritin (FRT) with the ~11 fold increase showed the most change. Significant reduction in HEPC and increase in ERFE levels were detected in patients as compared to the control group, while no direct correlation was identified with the other measured ISPs. Receiver operating characteristic (ROC) analysis showed that the z-score of the composite of ERFE+FRT has a full diagnostic ability for β-TM. In conclusion, our finding indicated the correlation between different ISPs, FRT as the leading predictor of iron overload and tow main iron regulatory hormones.

Pearl millet is an important food crop in the arid and semi-arid tropical regions of Africa and Asia. These regions are home to millions of poor smallholder’s households living in harsh agro ecology and reported higher prevalence of malnutrition. Such poor households have few options in terms of food crops, besides the limited markets. Indeed, pearl millet is one of the food crops they continue to grow for their food and nutritional security. Pearl millet is important sources of dietary carbohydrates, energy, protein, and important minerals such as calcium, iron and zinc. Considering inherent high nutritional values and climate resilient nature (drought and heat), demand for pearl millet as food, beside valued for its Stover as a source of livestock fodder, is projected to grow strongly in Asia (India) and Africa (West and Central Africa). Iron (cause anemia) and zinc (cause stunting) deficiencies are widespread and serious public health problems worldwide, including India and Africa. Biofortification is a cost-effective and sustainable agricultural strategy to address this problem. Research on pearl millet has shown that large genetic variability (30-140 mg/kg Fe and 20-90 mg/kg Zn) available in this crop can be effectively utilized to develop high-yielding cultivars with high iron and zinc densities. Both Open –pollinated varieties (Dhanshakti and Chakti) and hybrids (ICMH 1202, ICMH 1203 and ICMH 1301) of pearl millet with high grain yield (>3.5 tons/ha in hybrids) and high levels of iron (70-75 mg/kg) and zinc (35-40 mg/kg) densities have been developed and released. Currently, India growing >70,000 ha of biofortified pearl millet, besides more pipeline hybrids and varieties are under various stage of testing at the national (India) and international (west Africa) trials for possible release. Genomic tools will be an integral part of breeding program particularly for nutritional traits to use diagnostic markers and genomic selection. Clinical studies showed that 200g grains from biofortified cultivar would provide bioavailable Fe to meet full recommended daily allowance (RDA) in children, adult men and 80% of the RDA in women. Till today, no markets to promote biofortified cultivars/grains/products as no incentive price and such products aims to address food and nutritional security challenges simultaneously. The demand is likely to increase only after investment and integration into modern public distribution system, nutritional intervention schemes, private seed and food companies with strong mainstreaming nutritional policies. In the non-traditional regions, this will contribute to livestock and poultry feed industry as spill-over benefits to improve nutrition.

Nuclear receptor coactivator 4 (NCOA4) is a selective cargo receptor that mediates the autophagic degradation of ferritin (“ferritinophagy”), the cytosolic iron storage complex. NCOA4-mediated ferritinophagy maintains intracellular iron homeostasis by facilitating ferritin iron storage or release according to demand. Ferritinophagy is involved in iron-dependent physiological processes such as erythropoiesis, where NCOA4 mediates ferritin iron release for mitochondrial heme synthesis. Recently, ferritinophagy has been shown to regulate ferroptosis, a newly described form of iron-dependent cell death mediated by excess lipid peroxidation. Dysregulation of iron metabolism and ferroptosis have been described in neurodegeneration, cancer, and infection, but little is known about the role of ferritinophagy in the pathogenesis of these diseases. Here, we will review the biochemical regulation of NCOA4, its contribution to physiological processes and its role in disease. Finally, we will discuss the potential of activating or inhibiting ferritinophagy and ferroptosis for therapeutic purposes.

One consequence of the global technological advancement in conventional metallurgy is the fast depletion rate of valuable minerals, which are also becoming increasingly difficult to find in pure and economically viable forms. This has spurred more interest in technologies that investigate ability of different microorganisms to mobilize valuable metals from their ores via diverse metabolic processes. This study was carried out therefore to isolate, identify and characterize iron solubilizing bacteria from Iron stones of Agbaja iron ore mining site of Kogi State, Nigeria. Crushed samples in the range of 0.25µm and 0.75µm particle sizes were cultured in a modified 9k media to facilitate bacterial growth and pure cultures were then isolated and sub-cultured for further bioleaching studies. Morphological and biochemical analysis suggests that some of the bacteria identified are members of Acidithiobacillus spp, Pseudomonas spp, and Leptospirillum spp. Studies conducted on pure cultures and mixed consortium of the identified organisms shows that a mixture of the three organisms leached iron ore to about 96.16%. Also results of growth pattern due to bacteria countafter 24-72hours of incubation ranged between 0.1×10³ cfu/ml and 12.3 ×10³ cfu/ml for Acidithiobacillus spp. The need to explore the molecular characteristics of these organisms with a view to generating more information on the quality/quantity of their DNA for future cloning activities was also investigated in this work. DNA was extracted using zymo fungal/bacterial extraction mini prep kit ^TM (cat #6001) and subsequently subjected to 1% agarose gel electrophoresis. Visible bands were obtained with Alpha Innotech Gel Documentation Machine. DNA amplification was carried out using a pettier based thermo cycler PCR machine and electrophoresed on 1.5% agarose gel. Results of the PCR shows a visible band corresponding to 1.5kbp using this primer 27F (5¹-GAGTTTGATCCTGGCTCAG-3¹) and 1492R (5^1-GGTTACCTTGTTACGACT-3¹). DNA purity check shows two of the bacteria possess very good qualities for sequencing for further molecular analysis.

In the field of engineering, tracked vehicles play a significant role in accessing challenging terrains. Maintaining trafficability is of the utmost importance when it comes to tracked vehicles traversing rugged terrains; it provides stability, traction, and adaptability for a wide range of applications, including deep-sea exploration. The terrain characteristics pertain to the interactions that determine the mobility of tracked vehicles. Traditional Terramechanics models are in-adequate in depicting the correlation between tracks and soil. An important issue is the lack of consideration for the moisture content in the soil and the rate at which sinking occurs in these models. Examining sinkage speed helps describe the ability of tracked vehicles to move at high speeds. The focus is on the critical factors influencing the mobility of tracked vehicles, precisely the sinkage speed and its relationship with pressure. Experimental tests in a soil bin, utilizing Bentonite/Diatom sediment soil, aim to measure these terrain factors. The study introduces a rubber-tracked vehicle, pressure, and moisture sensors to monitor pressure sinkage and moisture, evaluating cohesive soils (Bentonite/Diatom) in combination with sand and gravel mixtures. Findings reveal that higher moisture content in Bentonite soil leads to increased track slippage and sinkage compared to Diatom soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics in contrast to bentonite soil. The distinct behaviors of these soils underscore the complexity of terrains, emphasizing the need for a meticulous understanding of soil properties before applying them in natural environments. Furthermore, this study contributes precision in assessing natural terrains, enhancing tracked vehicle design, and advancing terrain mechanics comprehension for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

Tracked vehicles play a vital role in accessing challenging terrains, offering stability, traction, and versatility for various applications, including deep-sea exploration. However, the seafloor and sediment contain valuable but poorly understood resources, making it a significant challenge for tracked vehicles during exploration. Consequently, it is imperative to conduct comprehensive studies before considering these terrains for off-road purposes. In this study, we developed a rigid, flexible track vehicle equipped with various sensors, focusing on monitoring pressure sinkage. Cohesive soils like Bentonite and Diatom soil, particularly when combined with sand and gravel mixtures, were used for the investigation and assessed for ground pressure, bearing capacity, and sinkage in rigid-flexible tracked vehicles on these characterized terrains under varying moisture conditions. Our findings indicated that increased moisture content in bentonite soil resulted in significantly higher track slippage and sinkage compared to diatomaceous earth soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics compared to bentonite soil. These significant variations between these two soil types under changing moisture conditions highlight the complexity of such terrains. Therefore, understanding the soil and its physical properties is crucial before applying them to natural terrains. Furthermore, this study emphasizes the importance of precision in assessing the physical properties of natural terrains for the development of tracked vehicles for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

Underwater acoustic spiral sources are able to generate spiral acoustic fields where the phase depends on the bearing angle. It allows to estimate the bearing angle relatively to a receiver by subtracting the phases of a spiral and a circular wavefront, and finds application in the bearing angle estimate with a single hydrophone, e.g., for unmanned underwater vehicles localization. This paper presents a new prototype for a spiral acoustic source, which is able to generate the required wavefronts, and is composed of four monopoles in the same piezoceramic cylinder. This paper reports the prototyping and the acoustic tests performed in a water tank where the spiral source was characterized in terms o Transmitting Voltage Response, phase, and horizontal and vertical directivity patterns. A receiving calibration method for the spiral source is proposed and shows a maximum angle error of 1 degree when the calibration and the operation are carried under the same conditions and a mean angle error up to 6 degrees for frequencies above 25 kHz when the same conditions are not fulfilled.

The diagnosis of a rolling bearing for monitoring its status is critical for maintaining industrial equipment using rolling bearings. The traditional method of diagnosing faults of the rolling bearing has low identification accuracy, which needs artificial feature extraction to enhance the accuracy. 1D-CNN method not only can diagnose bearing faults accurately but also overcome shortcomings of the traditional methods. Different from machine learning and other deep learning models, the 1D-CNN method does not need pre-processing one-dimensional data of rolling bearing’s vibration. Thus, it enhances the processing speed and improves the network structure to have a reasonable design for small sample data sets. This study proposes and tests a 1D-CNN method for diagnosing rolling bearings. By introducing the dropout operation, the method obtains high accuracy and improves the generalizing ability. The experimental results show 99.52% of the average accuracy under a single load and 98.26% under different loads.

In this paper, we introduce the Prognostics and Health Management of gear bearing system using autoencoder neural networks. Bearings and gears are the most common mechanical components in rotating machines, and their health conditions are of great concern in practice. This study presents an outlier modeling method for forecasting the gear bearing system failure using the health indicators constructed from mechanical signal processing and modeling. Outlier modeling aims to find patterns in data that are significantly different from what is defined as normal. In the unsupervised outlier modeling setting, prior labels about the anomalousness of data points are not available. In such cases, the most common techniques for scoring data points for outlyingness include distance-based methods density-based methods, and linear methods. The conventional outlier modeling methods have been used for a long time to detect anomalous observations in data. However, this paper shows that autoencoders are a very competitive technique compared to other existing methods. The developed method is demonstrated using the IMS bearing data from NASA Acoustics and Vibration Database.

In this study we used a non-autonomous Chua’s Circuit, and the fractional Lorenz chaos system together with a detection method from Extension theory to analyze the voltage signals. The measured bearing signals by acceleration sensor were introduced into the master and slave systems through a Chua’s Circuit. In a chaotic system minor differences can cause significant changes that generate dynamic errors, and extension matter-element models can be used to judge the bearing conditions. Extension theory can be used to establish classical and sectional domains using the dynamic errors of the fault conditions. The results obtained were compared with those from Discrete Fourier Transform analysis, Wavelet analysis and an integer order chaos system. The diagnostic ratio showed the fractional order master and slave chaos system calculations. The results show that the method presented in this paper is very suitable for monitoring the operational state of ball bearing system to be superior to the other methods. The diagnosis ratio was better and there were other significant advantages such as low cost and few.

In order to tackle the issue of severe rocking phenomenon under seismic conditions in structures equipped with steel spring isolation bearings, this paper investigates a novel type of anti-rocking bearing. Firstly, the structural configuration and working principle of the novel anti-rocking bearing are introduced, and a design method for bearing parameters is proposed. Secondly, a finite element analysis model is established using SAP2000 software to conduct nonlinear dynamic time history analysis under seismic loading. The analysis results show that the structural arrangement of the novel anti-rocking bearing reduces both the vertical displacement difference and the rocking angle of the isolation layer. The bearing exhibits a certain level of anti-rocking effect, but it may cause significant tensile forces in some bearings, necessitating the installation of anti-tensile reinforcement. The effectiveness of the anti-rocking effect improves as the stiffness of the steel tension rod in the bearing increases; however, it also leads to higher maximum tension in individual bearings as well as the total tension in all bearings. For structures equipped with the novel anti-rocking bearing, the acceleration amplifies under most cases, with amplification coefficients ranging from 0.82 to 1.55. The performance of the novel anti-rocking bearing varies significantly for different seismic waves. The stiffness of the steel tension rod should be determined considering the reference pressure of the bearing and the maximum designed tension of the bearing. Through the finite element simulation of the bearing, the mechanical properties of the bearing are basically the same as the theoretical analysis results. For the cylinder and the joint bearing, certain structural measures need to be taken to ensure its strength and stiffness.

This study examined the impact of differences in fruit load of olive trees on the rate of stem refilling. The experiment was conducted in a commercial olive orchard over the consecutive years of 2021 and 2022, during which the biennial bearing cycle of olive trees resulted in minimal fruit production in 2021 and maximal production in 2022. The rate of stem refilling was determined by quantifying the differences in water volume traversing the apex and base of the principal branches of experimental trees using sap flow sensors. Concurrent measurements of tree water status were also conducted using psychrometers, while soil moisture content dynamics were continuously recorded. Results indicate that alternate bearing significantly influences the stem refilling process, while soil moisture availability also plays a pivotal role. Water reserves were more intensively utilized during the year of full production (“ON” year) primarily to fulfill the water demands of developing fruits. This replenishment occurred in various periods during the day, including early morning, afternoon, and night, when stomatal conductance measurements indicated stomatal closure. The study suggests a more intense replenishment of reserves during the night in "ON" year trees, irrespective of soil moisture, water vapor pressure deficit, or phenological fruit development stage.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

Blind deconvolution (BD) is one of the effective methods that help pre-process vibration signals and assist in bearing fault diagnosis. Currently, most BD methods design an optimization criterion and use frequency or time domain information independently to optimize a deconvolution filter. It recovers weak periodic impulses related to incipient faults. However, the random noise interference may cause the optimizer to overfit. The time-domain-based BD methods tend to extract fault-unrelated single peak impulse, and the frequency-domain-based BD methods tend to retain the maximum energy frequency component, which will lose the fault-related harmonics frequency components. To solve the above issue, we propose a hybrid criterion that combines the kurtosis for time domain optimization and the $G-l_1/l_2$ norm for the frequency domain. These two criteria are monotonically increasing and decreasing, so they mutually constrain to avoid overfitting. After that, we design a multi-task one-dimensional convolutional neural network with time and frequency branches to achieve an optimal solution for this hybrid criterion. The multi-task neural network realizes the simultaneous optimization of two domains. Experimental results show that our proposed method outperforms other state-of-the-art methods.

Abstract: This paper is focusing on the stabilisation of soil using jute fibre as soil stabilizer. Stabilisation is the process of modifying the properties of a soil to improve its engineering performance and used it for a variety of engineering works. This study examines the potential of soil stabilization with jute fibre when it is cut into roughly 30mm lengths as stabilizer. The varying percentages like 0.5%, 1%, 1.5 and 2% of pieces of jute fibre were used and mixed it with soil. The laboratory tests such as California Bearing Ratio (CBR) test, modified compaction tests and direct shear strength tests have been conducted to observe the change in engineering properties of soil. On the basis of the experiments performed, it can be concluded that the stabilization of soil using 30mm pieces of jute as stabilizer improves the strength characteristics of the soil so that it becomes usable as one of the reinforcing material for the construction of roadways, parking areas, site development projects, airports and many other situations where sub-soils are not suitable for construction.

Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

Background and objectives: sickle cell disease is the most common hemoglobinopathy in the world. It is considered to be a real public health problem. Sickle cell patients are subjected to several factors causing inflammation such as iron metabolism. The study aimed to look for inflammation in children with sickle cell disease in Cameroon, identify the factors associated with inflammation, and raise the consequences for the patient including the iron profile and the profile of the hemogram. Materials and methods: We conducted an analytical cross-sectional study for 03 months. The sickle cell disease patients coming and/or followed at the Hematology Department of the Regional Hospital of Bafoussam and the Central Hospital of Yaoundé have been recruited. The exploration of inflammation was made by determining CRP, IL6, and ferritin concentrations. The hematological parameters and iron profile were evaluated using standard methods. Statistical analysis of the data was performed; Univariate and multivariate logistic regression analyses allowed to identification of factors associated with inflammation in patients, using the statistical tool R version 4.1.1.. The proportions were compared with the chi-square test when the expected numbers were greater than 5 and the Fisher test when not. Results: The frequency of inflammation in the population was 42.3%. Hyperferritinemia was significantly greater (p<0.001) in patients with inflammation compared to the non-inflammatory patients (96.8% and 76.7% respectively). Patients with inflammation showed a significant elevation of iron parameters (p<0.05). In addition, ferritin and IL6 elevation were associated with inflammation during sickle cell disease respectively (Or = 4.96; 95% CI [1.15-36.42]; p=0.056) and (Or =6.23; 95% CI [1.43-45.96]; p=0.030). Conclusions: The elevated iron in plasma is an effect of inflammation in sickle cell patients. Hence the need of controlling inflammation and iron in the latter is necessary.

We have successfully synthesized a series of Bi doped BaFe2As2 high quality single crystals for the first time. The x-ray diffraction (XRD) patterns show an expansion of lattice parameter c with Bi doping, indicating a negative pressure effect. By investigating the resistivity, a Fermi liquid (FL) to non-Fermi liquid (NFL) crossover is observed from normal state to antiferromagnetic order state, accompanied by three superconducting transitions labeled as SC I, SC II and SC III which are supposed to be induced from three superconducting realms with various Bi concentration. Thus, the NFL behavior is proposed to be closely related with the presence of superconductivity. The magnetic susceptibility measurements further speculates that the SC I and SC III phases should be filamentary superconductivity while the SC II be a possible bulk superconductivity with TC 7 K.

Organometallic drug development is still in its early stage, but recent studies show that organometallics having iron as the central atom have the possibility of becoming good drug candidates because iron is an important micro-nutrient, and it is compatible with many biological systems, including the human body. Being an eco-friendly Lewis acid, iron can accept the lone pair of electrons from imino(sp2)-nitrogen, and the resultant iron-imine complexes with iron as a central atom have the possibility of interacting with several proteins and enzymes in humans. Iron-imine complexes have demonstrated significant potential as anticancer, bactericidal, fungicidal, and other medicinal activities in recent years. This article systematically discusses major synthetic methods and pharmacological potentials of iron-imine complexes having in vitro activity to significantly affect clinical performance from 2016 to date. In a nutshell, this manuscript offers a simplistic view of iron complexes in medicinal inorganic chemistry: for instance, iron is presented as an "eco-friendly non-toxic" metal (as opposed to platinum) that will lead to non-toxic pharmaceuticals. The abundant literature on iron chelators shows that many iron complexes, particularly if redox-active in cells, can be quite cytotoxic, which can be beneficial for future targeted therapies. While we made every effort to include all the related papers, any omission is purely unintentional.

Ferroptosis is a recent form of non-apoptotic cell death, which occurs due to imbalance of iron homeostasis (iron overload). Oxidative stress due to the impairment of the antioxidant system is a major pathophysiology during ferroptosis, which eventually results in lipid peroxidation. The cellular and physiological biomarker of ferroptotic cell death includes major alteration in the glutathione peroxidase 4 (GPX4) antioxidant system and lipid peroxidation induced loss of plasma membrane integrity. This review elaborates the mechanism of oxidative stress which triggers ferroptosis.

In this presented case, a 77 years old woman suffering from ongoing knee pain underwent a bone scan using 99mTc-hydroxydiphosphonate (HDP) in suspicious for bone infection. An incidental finding from this scan revealed diffuse cardiac uptake, necessitating further diagnostic procedures to exclude the possibility of cardiac amyloidosis. In the subsequent 99mTc-3,3-diphosphono-1,2-propanodicarboxylic acid (DPD) scan and SPECT images, no perceptible cardiac uptake was observed at all. Upon retrospective review of the patient’s medical records, she had received 1000mg of ferric carboxymaltose for iron-deficient anemia, the day before the 99mTc-HDP bone scan. Therefore, it is assumed that the diffuse and temporary cardiac activity was due to the transient iron overload. We present and share this bone scan images in order to avoid possible future misinterpretation of cardiac amyloidosis.

This contribution was devoted to unveil the strain rate sensitivity (SRS) of G18NiCrMo3-6 cast steel in tension/compression asymmetry. For that purpose, detailed mechanical characterization tests were conducted providing a process window covering quasi-static and medium strain rate regimes (0.001, 0.1, 10 [ s¯¹]) in tension and compression states. By means of this experimental ef-fort, the SRS of the material could be extracted by a function of strain and strain rate which ena-bling to create a mathematical expression to easily be implemented as a state variable for constitu-tive material modeling. Finally, a pressure and rate dependent constitutive material model on the basis of Cocks'89 yield locus definition was created by a subroutine (UMAT) file and the material parameters were verified with respect to the experimental data. The UMAT file also takes into account the tension/compression asymmetry in yielding to handle the effect of porous media plas-ticity concept. The predictions of the proposed material model are quite in line with the experi-mental outputs.

Background. Intravenous iron therapy is used in treatment of anemia in uremic pa-tients. In patients treated with peritoneal dialysis iv. infused iron diffuses into the peritoneal cavity and may cause injury to the mesothelial cell. Methods. We studied effect of Iron Isomaltoside (IIS) in presence of NF-κβ inhibitor dehydroxymethyepoxyquinmicin (DHMEQ) on function of the peritoneal mesothelial cells. Experiments were performed on human peritoneal mesothelial cells in in vitro culture ex-posed to IIS 15 ug/dL ± DHMEQ 1 ug/mL. Intracellular oxidative stress, secretory activity and collagen synthesis in the cells were studied. Results. IIS induced oxidative stress in the mesothelial cells and that effect was weaker in presence of DHMEQ (-52%,p<0.001). In cells exposed to IIS increased expression of genes for IL6 (+74%,p<0.001), PAI-1 (+43%, p<0.01) and TGFβ (+53%,p<0.001) was observed and reduced for tPA (-36%,p<0.01). In presence of IIS increased secretion of IL6 (+56%, p<0.001), TGFβ (+49%,p<0.001) and PAI-1 (+51%, p<0.001) was observed whereas secretion of tPA was reduced (-25%, p0.001). DHMEQ reduced changes in genes and secre-tory activity caused by IIS. In presence of IIS synthesis of collagen in mesothelial cells was increased (+45%,p<0.001) and that effect was weaker (-25% vs. IIS, p<0001) when simulta-neously DHMEQ was used. Discussion. IIS induces proinflammatory changes in mesothelial cells, deteriorates their fibrinolytic activity and stimulates synthesis of collagen. All these effects are reduced when simultaneously NF-κβ inhibitor – DHMEQ is used.

Nitriding has long been used to engineer the surfaces of engineering steels to improve their surface and subsurface properties. The role of the surface compound layer (’-Fe4N and/or -Fe2-3N) in improving the tribological and corrosion resistant properties of nitrided steels has been established. However, there have been very few studies on the response of the compound layer to tribocorrosion in corrosive environments. In this work, the tribocorrosion behaviour of a 5 m thick ’-Fe4N nitride layer produced on mild steel (MS) by plasma nitriding has been studied in a NaCl containing solution under various electrochemical conditions. The results show that at a cathodic potential, where mechanical wear is predominant, the total material removal (TMR) from the ’-Fe4N layer is 37% smaller than that from the untreated MS, and at open circuit potential, TMR from the layer is 35% smaller than that from the untreated MS, while at an anodic potential, the ’-Fe4N layer can reduce TMR from mild steel by 87%. The beneficial effect of the ’-Fe4N nitride layer in improving the tribocorrosion behaviour of mild steel is derived from its high hardness and good corrosion resistance in the test solution and its ability to resist both mechanical wear and chemical wear.