Pin-on-plate and pin-on-disk wear tests are typically used for assessing the wear behavior of a given material coupling. Such a behavior is frequently described by a wear coefficient k, which is estimated, according to the Archard’s law, as the ratio between the measured wear volume V and the product of the applied normal force F and the sliding distance s, i.e. k=V/(F s). This study demonstrates that such a relationship is correct for pin-on-plate but not for pin-on-disk, particularly for flat-ended pins. Both analytical and finite element models of the two tests were developed, considering three different distances pin-disk axis. As results, wear volumes, pressure and wear depth maps were examined and compared for the same sliding distance. Though this study is focused only on the initial transient part of the wear tests, some interesting aspects arose: i) rotational effect in pin-on-disk tests affects k estimation, especially when the pin is near to the disk axis; ii) a simple analytical function is defined to correct the wear volume estimation for pin-on-disk tests; iii) due to the different sliding distances of contact points in pin-on-disk tests, pressure redistribution occurs with higher values on the inner side (closer to disk axis); the opposite trend is observed in wear depth maps. From a computational point of view, the pin-on-disk problem, only apparently simple, required very small time increments to correctly describe the circular trajectories of points, with high computational costs. Numerical strategies are currently under investigation to extend the study to the steady state phase of both tests.

Manufacturing of grinding wheels is continuously adapting to new industrial requirements. New abrasives and new wheel configurations, together with wheel wear control allow for grinding process optimization. However, the wear behavior of the new abrasive materials is not usually studied from a scientific point of view due to the difficulty to control and monitor all the variables affecting the tribochemical wear mechanisms. In this work an original design of pin on disk tribometer is developed in a CNC grinding machine. An Alumina grinding wheel with special characteristics is employed and two types of abrasive are compared: White Fused Alumina (WFA) and Sol-Gel Alumina (SG). The implemented tribometer reaches sliding speeds of between 20 and 30 m/s and real contact pressures up to 190 MPa. The results show that the wear behavior of the abrasive grains is strongly influenced by their crystallographic structure and the tribometer appears to be a very good tool for characterizing the wear mechanisms of grinding wheels, depending on the abrasive grains.

Current, application-driven trends towards larger-scale integration (LSI) of microfluidic systems for comprehensive assay automation and multiplexing pose significant technological and economical challenges to developers. By virtue of their intrinsic capability for powerful sample preparation, centrifugal systems have attracted significant interest in academia and business since the early 1990s. This review models common, rotationally controlled valving schemes at the heart of such “Lab-on-a-Disc” (LoaD) platforms to predict critical spin rates and reliability of flow control mainly based on geometries, location and liquid volumes to be processed, and their experimental tolerances. In absence of larger-scale manufacturing facilities during product development, the method presented here facilitates the provision of efficient simulation tools for virtual prototyping and characterization to greatly expedite design optimization according to key performance metrics. This virtual in silico approach thus significantly accelerates, de-risks and lowers costs along the critical advancement from idea, fluidic testing, bioanalytical validation and scale-up to commercial mass manufacture.

Non-genuine medical products, including diagnostic devices, have become a lucrative business for fraudsters, causing significant damage to revenues and reputation of companies, as well as posing a significant risk to the health of people and societies. Along a “digital twin” representing centrifugal microfluidic flow control on exemplary “Lab-on-a-Disc” (LoaD) systems, a novel, two-pronged strategy to safeguard miniaturized point-of-care devices by means of secret features and manufacturing challenges is outlined; such “hardware encryption” is flexibly programmed for each chip during production, and deciphered from a secure, local or online database at the time of use. This way, unlicensed copying may be efficiently deterred by an unfavourable economy-of-scale, even in absence of legal prosecution.

Enhancing the degree of functional multiplexing while assuring operational reliability and manufacturability at competitive costs are crucial ingredients for enabling comprehensive sample-to-answer automation, e.g., for use in common, decentralized “Point-of-Care” or “Point-of-Use” scenarios. This paper demonstrates a model-based ‘digital twin’ approach which efficiently supports the algorithmic design optimization of exemplary centrifugo-pneumatic (CP) dissolvable-film (DF) siphon valves towards larger-scale integration (LSI) of well-established “Lab-on-a-Disc” (LoaD) systems. Obviously, the spatial footprint of the valves and their upstream laboratory unit operations (LUOs) have to fit, at a given radial position prescribed by its occurrence in the assay protocol, into the locally accessible disc space. At the same time, the retention rate of a rotationally actuated CP-DF siphon valve and, most challenging, its band width related to unavoidable tolerances of experimental input parameters, need to slot into a defined interval of the practically allowed frequency envelope. To accomplish particular design goals, a set of parametrized metrics is defined, which are to be met within their practical boundaries while (numerically) minimizing the band width in the frequency domain. While each LSI scenario needs to be addressed individually on the basis of the digital twin, a suite of qualitative design rules and instructive showcases structures are presented.

This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

Accurate localization of the fovea in fundus images is essential for diagnosing retinal diseases. Existing methods often require extensive data and complex processes to achieve high accuracy, posing challenges for practical implementation. In this paper, we propose an effective and efficient approach for fovea detection using simple image processing operations and a geometric approach based on the optical disc's position. A key contribution of this study is the successful determination of the temporal direction by leveraging readable asymmetries related to the optical disc and its surroundings. We discuss three methods based on asymmetry conditions, including blood vessel distribution, cup disc inclination, and optic disc location ratio, for detecting the temporal direction. This enables precise determination of the optimal foveal region of interest (ROI). Through this optimized fovea region, fovea detection is achieved using straightforward morphological and image processing operations. Extensive testing on popular datasets (DRIVE, DiaretDB1, and Messidor) demonstrates outstanding accuracy of 99.04% and a rapid execution time of 0.251 seconds per image. The utilization of asymmetrical conditions for temporal direction detection provides a significant advantage, offering high accuracy and efficiency while competing with existing methods.

Since its inception in the late 2000s, blockchain has emerged as a powerful tool for creating trust without intermediaries to incentivize global communities for working for a common goal, such as the improvement of its very ecosystem, its applications and community adoption. While first blockchains were mainly devised for confirming transactions of their innate cryptocurrencies like Bitcoin, smart-contract blockchains like Ethereum can interface with the real-world through so-called “oracles”, which feed trustful off-chain information. This paper introduces digital twins of physical objects and processes as computational oracles to effectively unleash the tremendous opportunity offered by blockchain to the realm of fundamental science, research and technology development (RTD). The crowdsourcing concept is illustrated with the example of centrifugal flow control in microfluidic “Lab-on-a-Disc” (LoaD) systems.

This paper deals with miniaturization technique based on frequency reduction using top loaded dielectric discs. In contrast to a simple monopole, the resonant frequency of monopole loaded with two dielectric discs changes from 1.98 to 1.29 GHz, resulting 34.84% reduction in resonant frequency keeping the antenna length (36.00 mm) unaltered. It is well-known fact that dielectric material can trap the energy to be delivered from source to antenna and as a result, it is unable to radiate efficiently. Then any approach to use the dielectric material for miniaturization process must, therefore, antenna coupled in such a way that it can radiate efficiently. The dielectric disc on top of monopole creates an inductive situation in a similar way to oppositely directed wire loop compensate the capacitive effect present at monopole causes the reduction in resonant frequency. This concept is implemented without sacrificing any desired features like bandwidth, radiation characteristics and efficiency (more than 98%) and analyzed with an equivalent circuit model. Experimental results illustrate good agreement with simulation results. This monopole antenna in car can be designed for GPS system, car to car communication, GSM or CDMA operation.

Among solar thermal collectors, the evacuated flat panel is emerging as a reference technology for operation at higher temperatures of up to 200 °C with an increased annual energy production owing to both direct and diffuse light capture. Accurate measurements of the optical properties of the selective absorbers used in such devices are key for a reliable estimation of the overall performance. These optical properties must be measured under high vacuum at high temperatures, conditions under which the panels are meant to operate. In this study, we accurately measured these properties using a calorimetric technique. The measurement procedure is based on a power balance equation for a flat sample suspended in a high-vacuum chamber with minimal thermal losses and is well adapted for this class of devices. Calorimetric measurements obtained under Sun and LED light revealed excellent reproducibility and good agreement with those obtained using traditional optical analysis at low temperatures in air. When extended up to the absorber stagnation temperature, which often exceeds 300 °C, the calorimetric measurements started to deviate from the optical measurements, indicating the importance of measuring under the operating conditions.

The Hwangdo tidal flat is an intertidal landform located in Cheonsu Bay, Taean-gun, Chungcheongnam-do, on the west coast of Korea. The topographical characteristics of the semi-enclosed bay on the eastern side of the study area include waterways, sandbars, small islands, and tidal flats. In this study, data were acquired from tide gauges installed on the Hwangdo Bridge, and the height of the ellipsoid was measured using a real-time kinematics global positioning system (RTK-GPS). Digital elevation model (DEM) using Matrice 300 drone data were also acquired after processing. The geochemical sediment characteristics in the study area were analyzed, together with tidal-flat exposure-time characteristics based on environmental factors. Sediment data (n = 107) collected from October 25 to 28, 2022 (Korean local time) were used to classify sediment particles according to Folk and Ward (1957). Sedimentary facies ranged from coarse sand (sand:mud ratio = 9:1) to sandy silt (sZ) followed by muddy sand (mS) and slightly gravelly sandy mud ((g)sM). Total organic carbon (TOC) in the surface sediments were also characterized based on a particle-size analysis. The mean change in tidal height measured at Hwangdo Bridge during the sampling period was ~7.53 m (minimum: –3.86 m, maximum: +3.67 m). Based on the Boryeong's sea level measurement tide data in 2022, the tidal area in the drone images ranged from 6.362 m² (0.006 km²) at DEM +4.0 to 4,841,078 m² (4.841 km²) at DEM –4.0 m, indicating an increase in the tidal-flat area according to the tidal level of up to ~800-fold. The daily average exposure time was 9.0 h (minimum: 1.5 h, maximum: 17.9 h). Based on the results of multivariate analysis using exposure times and a geochemical dataset, four groups were identified: upper, middle, and lower intertidal zones and regions with a relatively high organic-matter concentration. A determination of the main characteristics of the Hwangdo tidal flat according to their spatial distribution showed that, among various environmental factors, changes in the sand or clay sediment composition were determined by community factors. The results of this study demonstrate the four statistically processed groups of marine environmental characteristics in the Hwangdo tidal flats. Changes in sedimentary patterns, rather than in the exposure time, accounted for the differences in the sediment compositions of the upper, middle, and lower stations, a response that is expected to continue.

In this paper, a further mathematical analysis of some previous results of the author’s ongoing investigation regarding Prandtl’s equations is accomplished. In particular, the objective of the present work is the performance of an approximate explicit solution to Prandtl’s system of equations for a laminar, isothermal, incompressible and steady boundary layer flow of a Newtonian fluid, over an infinite horizontal flat plate.

In this research, the photocatalytic degradation of cypermethrin using Fe-TiO2 nanoparticles supported in a biomaterial was evaluated. The nanoparticles of TiO2 were synthesized by the green chemistry method assisted by ultrasound and doped by chemical impregnation using molar ratios Fe:Ti of 0, 0.05, 0.075 and 0.1, to make efficient use of direct sunlight (λ>310 nm). All nanoparticles were immobilized on the surface of spathe of coconut palm (Cocos nucifera). The degradation was carried out at room temperature and natural pH in a flat plate solar reactor, on which the composite material was subjected. The concentration of cypermethrin was determined after 12000 J/m2 of accumulated radiation from GC-MS and the resulting material was characterized by Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) image and selected area electron diffraction (SAED), Fourier transform infrared spectroscopy (FTIR), UV-Vis spectrophotometry of diffuse reflectance and BET surface area BET surface area. The best results were achieved with the use of Degussa TiO2 P-25, Fe:Ti=0 and Fe:Ti=0.05 in suspension, with percentages of degradation of cypermethrin of 99.84, 99.62, and 100%, respectively. However, the materials supported on the biomaterial of coconut, they allowed to reach degradation percentages higher than 80% with the advantage that it minimizes operating costs, since they are not necessary filtering or centrifuging processes to separate the catalyst.

In this study, the potential of Fe3Al coating material as an environmentally friendly alternative to coatings containing critical elements for brake discs was investigated. A buffer layer of Cr-Mo steel (Ferro 55) was applied to enhance coating quality and prevent the formation of hot cracks during solidification. Microstructural analysis of the cross-section of the coating showed that the buffer layer diffused into the Fe3Al coating, forming a combination of Fe3Al, Fe, and Fe3AlC0.5 phases. The tribological properties of the Fe3Al coating were evaluated by pin-on-disc tests using two different copper-free friction materials extracted from commercial brake pads. The wear results showed a coefficient of friction comparable to that of an uncoated disc, but with a reduction in Particulate Matter (PM) emissions, an interesting aspect that is gaining increasing importance in view of the upcoming international standards..

Fluidic larger-scale integration (LSI) resides at the heart of comprehensive sample-to-answer automation and parallelization of assay panels for frequent and ubiquitous bioanalytical testing in decentralized the point-of-use / point-of-care settings. This paper develops a novel “digital twin” strategy with an emphasis on rotational, centrifugo-pneumatic flow control. The underlying model systematically connects retention rates of rotationally actuated valves as a key element of LSI to experimental input parameters; for the first time, the concept of band widths in frequency space as the decisive quantity characterizing operationally robustness is introduced, a set of quantitative performance metrics guiding algorithmic optimization of disc layouts is defined, and the engineering principles of advanced, logical flow control and timing are elucidated. Overall, the digital twin enables efficient design for automating multiplexed bioassay protocols on such “Lab-on-a-Disc” (LoaD) systems featuring high packing density, reliability, configurability, modularity and manufacturability to eventually minimize cost, time and risk of development and production.

Basketball is a highly anaerobic game, that consists of high-intensity efforts followed by lower-intensity efforts. Postural deformities can be a limiting factor in achieving maximal performances in basketball. Flat feet are one of the most common deformities and they can lead to poorer performances, discomfort and pain. In this research we made an attempt to link the degree of feet flatness with sports performances among Icelandic adolescent basketball players. A sample of 100 basketball players was tested on a podoscope to establish the degree of feet flatness and all participants performed countermovement jump, 20m sprint and pushups in 30 seconds. No significant correlation was observed between feet status and sports performances. No differences were found between groups with and without flat feet, which indicates that feet flatness was not a limiting factor in achieving better results. However, we state that only strong and healthy feet might lead to excellent performance.

With superior optical properties, high flexibility in engineering its material properties, and strong capability for large-scale on-chip integration, graphene oxide (GO) is an attractive solution for on-chip integration of two-dimensional (2D) materials to implement functional integrated photonic devices capable of new features. Over the past decade, integrated GO photonics, representing an innovative merging of integrated photonic devices and thin GO films, has experienced significant development, leading to a surge in many applications covering almost every field of optical sciences. This paper reviews the recent advances in this emerging field, providing an overview of the optical properties of GO as well as methods for the on-chip integration of GO. The main achievements made in GO hybrid integrated photonic devices for diverse applications are summarized. The open challenges as well as the potential for future improvement are also discussed.

This paper aims to introduce the notions of various types of Qc-contractions for which we establish some fixed circle and fixed disc theorems in the setting of metric spaces. Some illustrative examples are also provided to support our results. Moreover, we present some fixed circle and fixed disc results of integral type contractive self-mappings.

Previous study demonstrated the reconstituted type I collagen matrix extracted from rabbit tendons enabled to regenerate the TMJ disc in the rabbit. The aim of this study was to investigate changes in the extracellular matrix (ECM) and mechanisms of regeneration in TMJ disc. In 36 New Zealand rabbits that underwent a partial discectomy, discs were replaced with reconstituted collagen templates for 3 months. A histological analysis showed that moderate to severe degeneration appeared in partially discectomized joints without implantation. In contrast, discs that received the reconstituted collagen template regenerated, and returned to normal to protect the joint. Cells in the regenerative tissue expressed ECM, and fibers became regular and compact due to tissue remodeling over time. Reparative cells differentiated into chondroblasts, and showed highly dense pericellular fibers. The morphology and collagen composition of the disc and condyle in the 3-month experimental group were similar to those of normal tissues. In conclusion, the reconstituted collagen template facilitated the regeneration of surgically discectomized discs. Type I and type II collagens play a crucial role in the regeneration of articular discs.

Hip replacement has significantly improved the quality of life of patients with symptomatic hip osteoarthritis. Metal-on-metal (MoM) bearings have been used with conventional total hip re-placement (THR) for several decades with promising results from early applications. Wear and corrosion of these implants may lead to a release of metal products into surrounding tissue and body fluids. From the 1980s onwards, the search for increasingly better coupling materials with low levels of wear led to the rise of hard-on-hard couplings such as ceramic-on-ceramic (CoC). The latter is currently the coupling with the longest known duration and with a wear rate close to zero. MoM coupling has been for a long time the most significative alternative, but systemic and local complications linked to the release of chromium and cobalt ions, determine the withdrawn from the market. One other alternative proposed over the time has been Ceramic-on-Metal (CoM) bearing. Preliminary results have been described as favourable, but due to the failures of metal on metal it has been withdrawn from the market, without causing significant clinical complications. In this narrative review, we analysed risks and benefits associated with the implantation of hybrid hard-on-hard bearings, such as CoM.

The case of a virtual bosonic scalar field phi(x) gravitationally coupled in a conformally flat spacetime is investigated. The action S is known to be Weyl invariant only for specific expressions of the potential V(phi). In the conformally flat FLRW case the harmonic angular frequency omega_k(eta) becomes uniquely temporally independent. Therefore any inertial observers embedded in a conformally flat FLRW spacetime all agree on the choice of virtual vacuum states. We postulate that the wavenumber k must be quantized in order to be able to regulate the vev by zeta regularization. Some fundamental implications of this result is derived, and likely conclusions drawn.

We obtain more straightforwardly the main intrinsic features of dark matter distribution in the halos of galaxies by considering the spherically symmetric space-time, which satisfies the flat rotational curve condition, and the geometric equation of state resulting from the modified gravity theory. In order to measure the equation of state for dark matter in the galactic halo, we provide a general formalism taking into account the modified f(X) gravity theories. Here, f(X) is a general function of X∈{R,G,T}, where R,G and T are the Ricci scalar, the Gauss-Bonnet scalar and the torsion scalar, respectively. These theories yield that the flat rotation curves appear as a consequence of the additional geometric structure accommodated by those of modified gravity theories. Constructing a geometric equation of state wX≡pX/ρX and inspiring by some values of the equation of state for the ordinary matter, we infer the properties of dark matter in galactic halos of galaxies.

In this work we demonstrate non-flat metasurface holograms with applications in imaging, sensing, and anti-counterfeiting. In these holograms the image and its symmetry properties, with respect to the polarization of the light, depend on the specific shape of the substrate. Additionally, the sensitivity of the holographic image to the substrate shape can be engineered by distributing the phase information into determined areas of the metasurface.

Due to the retrognathic mandible, an orthodontist frequently observes skeletal class II malocclusion in growing patients. The preferred technique for analyzing and monitoring the temporomandibular joint alterations caused by the functional device is magnetic resonance imaging [MRI]. The study aimed to assess and compare changes in the articular disc's dimension and location before and following the use of various class II correctors to correct the class II molar relation using MRI technology. Methods: 39 adolescent patients aged 15-23 years old [24 girls and 15 boys] who were diagnosed with skeletal Class II division 1 malocclusion based on clearly defined criteria underwent treatment with either the power scope II [PS], Sabbagh Advanced Repositioning Appliance [SARA] and or Dynaflex [DF] with fixed appliances. For fixed functional treatment, the average length of treatment was 5-7 months. The changes in the articular disc dimension and position and condylar position were assessed. The study was done at the Department of Orthodontics at the College of Dentistry, Hawler Medical University in Erbil City. Results: Group DF has a significant effect on the condylar position index and posterior joint space on the closed mouth and disc length on both open and close mouth techniques, and in the group SARA, disc position, and condylar position index on closed mouth technique have shown that significant differences were observed. Conclusion: Class II malocclusions can be effectively corrected by fixed functional appliances. The statistical significance forward movement of the condyle in the glenoid fossa and the posterior movement of the articular disc concerning the condylar head was observed. The mechanism of action of functional appliances appears to include the forward migration of the C-GF complex.

In the following work, the assessment of the strength properties of the critical area of the rotor stage of the turbine jet engine was undertaken. This is the place of fixing the blade in the rotor disc. An important aspect of this issue are characteristic geometrical dimensions and operating factors e.g., change in rotor speed. In this paper, the assessment of the strength properties of the existing trapezoidal blade-disc connection was undertaken using parametric analysis considering FSI. Virtual models of the compressor rotor stage were developed, including parametric blade-disc connections and discrete models for FEM and CFD analyses. In the parametric analysis of the blade-disc connection, one-way fluid-structure coupling was used. The parametric analysis was aimed at assessing selected geometric parameters in terms of their impact on the maximum reduced stresses in the blade root. It was examined how the adopted value of the friction coefficient influences the maximum reduced stresses in the rotor stage of the compressor.

Our recent study detected the expression of a tissue Renin-Angiotensin System (tRAS) in human intervertebral discs (IVDs). The present study sought to investigate the impact of angiotensin II receptor type 1 (AGTR1) antagonist losartan on human nucleus pulposus (NP) cell inflammation and degeneration induced by tumor necrosis factor-α (TNF-α). Human NP cells (4 donors, Pfirrmann grade 2-3, 30-37 years old, male) were isolated and expanded. TNF-α (10 ng/mL) was used to induce inflammation and degeneration. We examined the impact of losartan supplementation and measured gene expression of tRAS, anabolic, catabolic, and inflammatory markers in NP cells after 24 h and 72 h of exposure, respectively. T0070907, a PPAR-gamma antagonist, was applied to examine the regulatory pathway of losartan. Losartan (1 mM) significantly impaired TNF-α induced increase of pro-inflammatory (nitric oxide and TNF-α), catabolic (matrix metalloproteinases), and tRAS (AGTR1a and Angiotensin Converting Enzyme) markers. Further, losartan maintained the NP cell phenotype by upregulating aggrecan and downregulating collagen type I expression. In summary, losartan showed anti-inflammatory, anti-catabolic, and positive phenotype modulating effects on human NP cells. These results indicate that tRAS signaling plays an important role in IVD degeneration, and tRAS modulation with losartan could represent a novel therapeutic approach.

Background and Objectives: Chondroitin sulfate ABC endolyase (condoliase) was launched as a new drug for chemonucleolysis in 2018. There are few Few studies assessed regarding its clinical outcomes, and many important factors matters still remain unclear. The purpose of this This study aimed is to clarify clarify the preoperative conditionsfactors for in which condoliase could beis highly effective. Materials and Methods: Of the 47 patients who received condoliase, 34 patients were enrolled in this study. The mean age of the patients was 33 years. The average disease duration since the onset of the disease was 8.6 months. We evaluated the patients’patient’s low back and leg painpains using a numericalNumerical rating scale (NRS) score at two time points (before therapy and 3 months after therapyadministration). We divided the patients into two groups ([good group [(G]:): NRS score improvement ≥ 50%, poor group (P): NRS score improvement < 50%]. The parameters evaluatedSurvey items were age, disease disease duration, body mass index (BMI), and the presence or absence of positive or negative straight leg raising (SLR) test results. In additionMoreover, the loss of disc height loss and participation of preoperative radiological findings were also evaluated. Results: In terms of low back and leg pain, the G group were in 9/34 (26.5%) and 21/34 (61.8%) patients, respectively. Patients’. Patient’s age (low back pain G/P, 21.0/36.5 years)), was significantly loweryounger in the G group of low back pain (p = 0.001). High intensity change inof the protruded nucleus pulposus (NP) and the spinal canal occupancy by theof NP ≥ 40% were significantly highhighly observed in those withthe leg pain in the G groups (14/21,: p = 0.04; and 13/21,: p = 0.03, respectively). Conclusions: The efficacy of improvement inof leg pain was significantlyhighly correlated with high intensity change and size of the protruded NP. Condoliase was not significantly effective forto low back pain, but could might be expected have anthe effect onto younger patients.

A multicenter, prospective cohort study conducted in 5 physiotherapy clinics in the UAE from January 2021 to March 2023 to assess coronal lumbar spine radiographic parameters as a predictor of conservative therapy outcomes in patients suffering from low back and leg pain due to lumbar disc herniation (HNP). Ninety patients (mean age 44 yrs., 54% male) with lumbar HNP underwent conservative therapy. All participants received lumbar spine MRI and radiography to assess spine alignment. Interventions included specific exercises, diathermy, traction, education, a home-based exercise pro-gram, and medications. Detailed demographic data was collected. Follow-up was 6-months after discharge. A successful outcome was based on a minimum of the following four outcomes: (1) reduction of pain by 17.5 points (0–100 NRS); (2) fatigue reduction by 7.5 points; (3) distress reduction by 5 points; and (4) interference reduction by 9.5 points. At 6-month follow-up it was found that patient age, education, and radio-graphic determined lumbosacral angle measures significantly affected the odds of a successful outcome. Increasing age 1-year significantly decreased the odds of success of improving pain, fatigue (OR = 0.85, p = 0.016) and interference scores (OR = 0.89, p = 0.042) by 15%, 15%, and 11% respectively. Lower education significantly increased the odds of success for improving pain, fatigue, and interference by 26.18, 26.18, and 7.5 (p = 0.006, = 0.006, and = 0.029 respectively). Increasing (worsening) the radiographic lumbosacral angle by each 1° significantly reduced the odds of success for improving pain, fatigue, distress, and interference by 3.52, 3.52, 27.99, and 2.55, respectively (p < 0.001, < 0.001, = 0.003, = 0.001). Our findings indicate that younger age, less education, and better coronal radiological lumbar spine alignment all had a substantial impact on the likelihood of success of 6-month outcomes in patients suffering from chronic lower back pain and radiculopathy due to HNP.

With the development of health service, animal husbandry, aquaculture and chemical industry, more and more pollutants are discharged into the water environment, including antibiotics and heavy metal ions. These hazard substances pose a great threat to environment safety and human health. As two kinds of new green solvents, ionic liquids (ILs) and deep eutectic solvents (DESs) are widely used in various fields including separation and environmental engineering, which are attracting huge attention from academia and industry. In this study, the optimal ionic liquid and deep eutectic solvent were selected and their complex with β-cyclodextrin (β-CD) were firstly prepared by simple and effective inclusion way. After necessary characterization and analysis, two kinds of complex were applied to prepare a special sorbent disc with two different sides by adding diluent (excipient) and pressing under 5~15 MPa. As the result, the IL and DES could be stably immobilized on the disc and play the key role in selective adsorption for targets. Besides that, the experiments of different hazardous substances achieved the expected results. Based on this study, the complex disc showed a lot of merits in the separation performance, easy preparation and use, simple operation, and good stability. It was believed to be a useful tool for water purification and detection.

The Drosophila imaginal disc has been an excellent model for the study of developmental gene regulation. In particular, long non-coding RNAs (lncRNAs) have gained widespread attention in recent years due to their important role in gene regulation. Their specific spatiotemporal expressions further support their role in developmental processes and diseases. In this study, we explored the role of a novel lncRNA in Drosophila leg development by dissecting and dissociating w1118 third-instar larval third leg (L3) discs into single cells and single nuclei, and performing single-cell RNA-sequencing (scRNA-seq) and single-cell assays for transposase-accessible chromatin (scATAC-seq). Single-cell transcriptomics analysis of the L3 discs across three developmental timepoints revealed different cell types and identified lncRNA:CR33938 as a distal specific gene with high expression in late development. This was further validated by fluorescence in-situ hybridization (FISH). The scATAC-seq results reproduced the single-cell transcriptomics landscape and elucidated the distal cell functions at different timepoints. Furthermore, overexpression of lncRNA:CR33938 in the S2 cell line increased the expression of leg development genes, further confirming its important role in development.

While immutability is Blockchain's* much celebrated covenant, change is the rule of life. The paradox has seriously limited real-world deployability of Smart Contracts (SC), faltering its mainstream adoption and sustainability. Once implemented, SC remains unstoppable even if its execution makes losses, as evident in the recently exploded $50+B DeFi industry. How do we reconcile the two and make DeFI/Blockchain profitable and sustainable? A DISC (Dynamic Immutable Smart Contract) hypothesis was proposed to resolve the paradox. Using an existing decentralized IoT device framework we test the DISC hypothesis, by designing/implementing a DISC protocol that delivers an algorithmically controlled dynamic off-chain data feed into a self-executing SC. The experiment successfully introduced limited dynamism into SC without compromising its immutability or undermining user control over their SC terms. If consistently reproduced in diverse settings, the DISC protocol could earn an important milestone in the evolution of Blockchain's decentralized economy of the future.

Alzheimer’s disease (AD) is a significant health concern worldwide with enormous social and economic impact globally. The gradual deterioration of cognitive functions and irreversible neuronal losses are primary features of the disease. Even after decades of research, most therapeutic options are merely symptomatic, and drugs in clinical practice present numerous side effects. Lack of effective diagnostic techniques prevents the early prognosis of disease, resulting in a gradual deterioration in the quality of life. Furthermore, the mechanism of cognitive impairment and AD pathophysiology is poorly understood. Microfluidics exploits different microscale properties of fluids to mimic environments on microfluidic chip-like devices. These miniature multichambered devices can be used to grow cells and 3D tissues in vitro, analyze cell-to-cell communication, decipher the roles of neural cells like microglia, and gain insights into AD pathophysiology. This review focuses on the applications and impact of microfluidics on AD research. We discuss the technical challenges and possible solutions provided by this new cutting-edge technique to understand disease-associated pathways and mechanisms.

Background: Exclusively breastfeeding your newborn while in the hospital is imperative for suc-cessful breastfeeding at home. This study will investigate if having a nurse on-site during rooming-in can enhance the proportion of exclusive breastfeeding. Methods: We carried out a prospective cohort study to assess exclusive breastfeeding in the first three months of life among two Neona-tology Units in Southern Italy with different hospital settings. The Ente Ecclesiastico Miulli of Ac-quaviva delle Fonti had on-site nurses available 24/7 (on-site group), while the Policlinico of Bari had nurses available on call 24/7 from the Neonatology Unit (on-call group). Results: Between January 3rd and March 31st, 2018, a total of 564 sets of mothers and babies were admitted - 299 on-site and 265 on-call. The exclusive breastfeeding rate for the entire group was 76.4% at 90 days, demonstrating the positive impact of rooming-in and nursing, regardless of the setting. Infants delivered via ce-sarean section in the on-site group demonstrated higher rates of exclusive breastfeeding at both 30 and 90 days of life. Conclusions: Our research indicates that having a nurse available at all times is crucial for promptly identifying any problems with breastfeeding. We highly suggest having an on-site nurse present during rooming-in for mothers who have had a caesarean delivery. This nurse should continuously promote exclusive breastfeeding until the baby is three months old.

Microfluidic lab-on-chip devices are widely being developed for chemical and biological studies. One of the most commonly used types of these chips is perfusion microwells for culturing multicellular spheroids. The main challenge in such systems is the formation of substantial necrotic and hypoxic zones within the cultured spheroids. Herein, we propose a novel acoustofluidic integrated platform to tackle this bottleneck problem. We show that such an approach enhances cell viability and shrinks necrotic and hypoxic zones in these spheroid-on-a-chip platforms without the need to increase the flow rate, leading to a significant reduction in costly reagents' consumption. Proof-of-concept, designing procedures, and finite element numerical simulation are discussed in details. Also, the effects of acoustic and hydrodynamic parameters on the cultured cells are investigated. The results show that by increasing acoustic boundary displacement amplitude (d0), the spheroid’s proliferating zone enlarges greatly. Moreover, it is shown that by implementing d0=0.5 nm, the required flow rate to maintain the necrotic zone below 13% will be decreased 12 times compared to non-acoustic chips.

The population parameters of the ecologically important mud shrimp Upogebia major were analyzed from 2012 to 2015 in tidal flats in Seonjaedo and Jugyo on the West coast of Korea. The shrimp density averaged 265/m2 in Seonjaedo and 118/m2 in Jugyo. The sex ratio varied monthly, often male-biased, but by size, males were significantly dominant, with a carapace length (CL) over 30 mm. Although the shrimp settled almost annually, only a single size-group was observed from 2012 to 2014. The recruitment in Jugyo in 2014 was notably successful, resulting in two cohorts persisting until 2015. Many shrimp were parasitized at varying local rates: 6.0% in Seonjaedo and 37.1% in Jugyo. The growth curves revealed that the shrimp grew annually after settlement, reaching CLs of 11.90, 18.24, and 23.02 mm in Seonjaedo and 13.73, 20.86, and 25.82 mm in Jugyo. Annual mortality was 77.2% in Seonjaedo and 67.4% in Jugyo. The estimated lifespan (tmax) was 10 years in Seonjaedo and 8 years in Jugyo, whereas the 2010 cohort in Jugyo largely disappeared in 5 years. Ovigerous females appeared from November to June and benthic juveniles between June and September. The shrimp’s growth was slower relative to other East Asian populations, likely due to colder sea water temperatures and altered food conditions from a higher shrimp density.

The second-order factor effect of burner optical ports and edge inter-matrices (EIM) and the first-order factor of pressure on the soot formation process and behavior of premixed sooting flames in a high-pressure burner are numerically investigated here. Three-dimensional computational fluid dynamics (CFD) simulations of a premixed flame C₂H₄/air at p = 1.01 and 10 bar using a one-step chemistry approach are first performed to justify the satisfied predictability of the prospective axisymmetric two-dimensional (2D) and one-dimensional (1D) simulations. The justified 2D simulation approach shows the generation of an axial vorticity around the EIM and axial multi-vorticities due to the high expansion rate of burnt gases at the high pressure of 10 bar. This leads to the development of axial multi-sooting zones, which are manifested experimentally by visible luminous soot streaks, and to the boosting of soot formation conditions of a relatively low-temperature field, < 1800 K, and a high mixing rate of gases in combustion around and above the EIM location. Nevertheless, a tolerable effect on the centerline soot volume fraction (f_V) profile, f_V < 3%, is manifested only at high heights above the burner of the atmospheric sooting flame C₂H₄/air ϕ = 2.1, and early at the high pressure of 10 bar of this flame, f_V < 10%. Enhancing the combustion process reactivity by decreasing the rich equivalence ratio of the fuel/air mixture and/or rising the pressure results in the prior formation of soot precursors, which shifts the sooting zone upstream.

Eccentric punching shear can occur in concrete slab-column connections when the connection is subjected to shear and unbalanced moments. Typically, this situation results in edge and corner columns and is thus a common practical case. However, most punching experiments in the literature are concentric punching shear. This paper presents a developed database of eighty-eight experiments of flat slabs under eccentric punching shear, including a summary of the testing procedure of each reference and a description of the slab specimens. Additionally, a linear finite element analysis of all the specimens is included to determine the relevant sectional shear forces and moments. Finally, the ultimate shear stresses from the database experiments are compared to the shear capacities determined with ACI 318-19, Eurocode 2 NEN-EN 1992-1-1:2005, and the Model Code 2010. The comparison shows that the Model Code 2010 is the most precise in the predictions with an average tested over predicted ratio of 0.96 and a coefficient of variation of 27.96%. It can be concluded that this study represents the inconsistencies of the currently used design methods and the lack of experimental information.

This paper investigates the improvement in solar energy collection and conversion using Al₂O₃-Water nanofluids in a solar flat plate collector (SFPC). The efficiency of a solar flat plate collector using water as the fluid medium is analyzed experimentally and theoretically. For theoretical analysis, a mathematical model in MATLAB is used to simulate and is validated by the experimental results. To enhance the solar energy collection and conversion efficiency of the SFPC, Al₂O₃-Water nanofluid was selected as the fluid medium. The nanofluid properties like density, specific heat capacity, thermal conductivity and viscosity are analyzed and compared for several models of Al₂O₃-Water nanofluids and the best model was selected to modify the simulation. Effect of particle diameter in the nanofluid was found to be marginal on the nanofluid properties. The optimum volume concentration of the nanofluid was found to be 4% giving an efficiency increase of 7.78% in the SFPC over the use of water. This reduces the area of the SFPC by 10.5%.

Background: This study aimed to investigate the association between the internal derangement of the temporomandibular joint (TMJ), in particular the severity of disc displacement (DD), and the presence of generalized joint hypermobility (GJH) in growing patients evaluated on magnetic resonance images (MRI). The study also investigated the relationship between the stages of DD severity and age. Methods: This cross-sectional study has been conducted on a pre-orthodontic population (8-16 years). The GJH was assessed with the Beighton test (cutoff ≥ 4) and the final sample of 56 patients was divided into two groups: a Study Group, 30 subjects with GJH, and a Control Group, 26 subjects without GJH. The disc position was evaluated on MRI and the severity of DD was classified in four stages. Pearson's χ2 Test was performed for the analysis of the statistical correlation. Results: A statistically significant relationship between GJH and disc position was found, in particular a disc displacement with reduction (DDwR) and DD severity. It also emerged a positive association between the severity of DD and age, that increased with increasing age. Conclusions: Growing patients with GJH have a higher risk of developing DD and with more severe stages. The risk of developing DD and the severity increases with increasing age.

Purpose: The intervertebral disc is a leading avascular organ in the body that may gather nutrition through diffusion. It maintains homeostasis by the use of autophagy and apoptosis to survive in unfavorable conditions such as stress and mechanical force. Therefore, excessive force and stress beyond normal conditions may cause intervertebral disc degeneration. The purpose of this study was to examine which is the better method, either external fixator (EF) or saline injection (SI), for inducing autophagy and apoptosis-mediated nucleus pulposus (NP) cell death in the discs of rat tail’s. Methods: Sixteen, nine-weeks-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross Kirschner wires) for a period ofsix and twelve weeks. Treated discs were dissected to identify the participation of autophagy and apoptosis in intervertebral disc degeneration. For identification purposes, H&amp;E staining, Masson’s trichrome staining, and immunohistochemistry (IHC) for LC3, beclin-1, and P62 in addition to MMP-2, MMP-3, and TIMP-1 were performed. Furthermore, we performed real-time polymerase chain reaction (RT-PCR) to observe autophagy-related gene expression (beclin-1, LC3, and P62) and apoptosis-related gene expression (MMP-2, MMP-3, and TIMP-1). Results: TheEF group showed more insidious NP cell degeneration than the control (Ctrl) group. Degeneration was elevated with increasing compression duration of EF group, whereas the SI group could not distinguish the margin of annulus fibrosus (AF) and NP cells. LC3, beclin-1, and P62 showed the highest and lateral expression whilst MMP-2, MMP-3, and TIMP-1 showed up-regulated and central expression in both groups, although the SI group could not recognize the boundary between NP and AF cells. The EF group showed the highest autophagy-related gene expression whereas the SI group showed lower expression. In addition, the EF group showed more autophagy-accumulating materials than the SI group which elevated with increasing compression duration. Furthermore, the SI group induced the highest apoptotic gene expression, but the EF group showed the lowest expression. Conclusion: The EF method was better for studying autophagy and apoptosis because it enhanced intervertebral disc degeneration after compression, which is actively linked to autophagy and apoptosis. The degeneration process was elevated by increasing the compression duration, but SI could not distinguish AF and NP cell margins.

Purpose: Intervertebral disc is a leading avascular organ in the body. Hence, it may utilize autophagy and apoptosis to alive in unfavorable condition like stress and mechanical force. But excessive force and stress is a key cause to intervertebral disc degeneration (IVDD). Purpose of this study is to identify, external fixator (EF) and saline injection (SI) may induce autopahgy and apoptosis mediated nucleus pulposus (NP) cells death in rat tail’s disc and which method is better for studying autophagy and apoptosis. Methods: Sixteen 9-week-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross kirschner wires) for 6 weeks and 12 weeks as well. Treated discs were dissected for checking out participation of autopahgy and apoptosis to intervertebral disc degradation (IVDD). For identifying them, we performed H&E staining, Masson’s trichrome staining, and Immunohistochemistry (IHC) for LC3, Beclin-1and P62 as well as MMP-2, MMP-3 and TIMP-1.Furthermore, we performed quantitative polymerase chain reaction (qPCR)to check out autophagy related gene expression (beclin-1, LC3 and P62) and apoptosis related gene expression (MMP-2, MMP-3 and TIMP-1) respectively. Results: More insidious nucleus pulposus (NP) cell degeneration was indentified in (EF) group than in (Ctrl) control group. And rate of degradation was elevated with increasing duration of compression, but SI group cannot distinguish the margin of AF and NP cells. Highest along with lateral expression was found for LC3, Beclin-1, and P62 of both groups. Up-regulated and central expression was observed for MMP-2, MMP-3 and TIMP-1 of both groups, although SI group cannot recognize the margin between NP and AF cells. Utmost autophagy related gene expression was identified in EF group than in SI group. Besides, maximum autophagy accumulating materials was found in EF group than in SI group. And it was amplified along with increasing the duration of compression. Highest, apoptotic gene expression was observed in SI group, whereas, EF group showed lowest expression. Conclusion: External fixator (EF) method was better to study autophagy and apoptosis because it enhanced IVDD after compression which is actively linked with autophagy and apoptosis. Degeneration process was conversely proportional along with duration of compression. On contrary, saline injection (SI) could not distinguish AF and NP cell border.

Optical communications are described and analyzed by shaped beams; we challenge the ‎effects of parameters that impact the profile of a Flat Top Gaussian (FTG) beam. When ‎the laser beam propagates throughout the atmosphere, it can be influenced by different ‎optical phenomena including scattering, absorption, and turbulence due to changes in the ‎scintillation index and the forms of intensity that are displayed in the source and receiver ‎planes. In this project, the FTG laser beam that propagates through a weak turbulent ‎region is numerically investigated using open-source software. This simulation will be ‎performed according to a mathematical model based on the split-step beam propagation ‎method. Intensity distributions at the source plane and the received average intensity in ‎atmospheric turbulence are calculated, and additional contour is in the transducer plane. ‎The scintillation index, structure constant, source size, and other parameters, are applied ‎in the Rytov method to quantify the weak turbulent model. Moreover, these parameters ‎are analyzed in near-field propagation. Also, the effects of the beam’s scintillation and ‎beam wander are determined. All results simulated are discussed and compared with the ‎TEM00 Gaussian beam. Finally, these results are compared to measurements in the ‎experimental part of the work.

Three-dimensional (3D) facies and petrophysical models were generated from previously published data of carbonate strata in the Dam Formation (eastern Saudi Arabia) to quantitatively investigate, describe, understand, model, and predict the permeability anisotropy of tidal flat carbonate within a sequence stratigraphic framework. The resulting 3D models were used to conduct fluid flow simulations to demonstrate how permeability anisotropy influences the production of hydrocarbons and ultimately affects decisions concerning future drilling in the exploration and development of carbonate reservoirs that have tidal flat strata. The constructed 3D facies model consists of four lithofacies associations, two of which were grain-dominated associations and two of which were mud-dominated associations. These lithofacies associations varied spatially in four reservoir zones (zones 1 to 4), which represent two fourth-order sequences in the uppermost part of the Dam Formation. Zones 1 and 3 consist of transgressive parasequences, and zones 2 and 4 consist of the regressive parasequences of these sequences. The 3D porosity and permeability models have a coherent match with the distribution of the lithofacies and the stratigraphic framework of the Dam Formation. The results suggested that the permeability anisotropy in zones 1 and 3 is controlled by the occurrence of the grain-dominated lithofacies associated with tidal flat channels. This lithofacies association overlies the sequence boundaries of sequences 1 and 3, forms reservoir bodies with relatively high permeability values, and is elongated perpendicular to the shoreline of the depositional environments. In contrast, permeability anisotropy in zones 2 and 4 is thought to be controlled by the occurrence of the grain-dominated lithofacies associated with the oolitic shoal. This lithofacies association overlies the maximum flooding surface of sequences 2 and 4, forms reservoir bodies with relatively high permeability values, and is elongated parallel to the shoreline of the depositional environments. Fluid flow simulation results suggested that the trend in hydrocarbon production from the constructed 3D models depends on permeability anisotropy in each reservoir zone. Thus, recognizing trends in permeability anisotropy, which might be predicted using sequences stratigraphy, could help to identify potential areas for future drilling.

In areas where conventional fundus cameras are logistically unaffordable, the smartphone-based approach is considered as a promising future of glaucoma screening due to their affordability and ease-of-use. Optic disc localization is a critical stage during glaucoma screenings. For fundus images captured with standard fundus cameras, the majority of the models available out there can locate the optic disc with satisfactory performance. However, for images that are captured with smartphone-based fundus cameras, the inherent noise and lower quality of the fundus image makes it difficult for models to detect the optic disc region. In this study, we have proposed to utilize YOLOv8n for optic disc localization due to the model’s cutting-edge performance in diverse tasks and its lightweight nature. We have used a public dataset which has 2000 low quality fundus images that are captured using a smartphone-based fundoscopy device. From these, 60% of the data was used for fine-tuning the model, and 25% for testing. By using a confidence of 50% set as threshold, the model was able to detect the optic disc successfully on over 97% of test images with intersection over union of above 0.85. These results highlight the potential of the lightweight YOLOv8n model for deployment on resource-constrained environments, offering a promising performance on accurately localizing the OD and enhancing the feasibility of affordable glaucoma screening on smartphones.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

Low back pain is a clinically highly relevant musculoskeletal burden and is associated with inflammatory as well as degenerative processes of the intervertebral disc. However, the pathophysiology and cellular pathways contributing to this devastating condition are still poorly understood. Based on previous evidence, we hypothesize that tissue renin-angiotensin system (tRAS) components, including the SARS-CoV-2 entry receptor angiotensin-converting enzyme 2 (ACE2), are present in human nucleus pulposus (NP) cells and associated with inflammatory and degenerative processes. Experiments were performed with NP cells from 4 human donors. The existence of angiotensin II, angiotensin II type 1 receptor (AGTR1), AGTR2, MAS-receptor (MasR), and ACE2 in human NP cells was validated with immunofluorescent staining and gene expression analysis. Hereafter the cell viability was assessed after adding agonists and antagonists of the target receptors as well as angiotensin II in different concentrations for up to 48 hours of exposure. A TNF-α-induced inflammatory in vitro model was employed to assess the impact of angiotensin II addition and the stimulation or inhibition of the tRAS receptors on inflammation, tissue remodeling, expression of tRAS markers, and the release of nitric oxide (NO) into the medium. Further, protein levels of IL-6, IL-8, IL-10, and intracellular as well as secreted angiotensin II were assessed after exposing the cells to the substances, and inducible nitric oxide synthase (iNOS) levels were evaluated utilizing Western Blot. The existence of tRAS receptors and angiotensin II were validated in human NP cells. Cell viability analysis revealed no cytotoxic effects of angiotensin II. The AGTR1 inhibitor Candesartan and the MAS receptors AVE0991 showed cytotoxic effects at high concentrations (100 µM). The addition of angiotensin II only showed a mild impact on gene expression markers. However, there was a significant increase in NO secreted by the cells. The gene expression ratios of pro-inflammatory/anti-inflammatory cytokines IL-6/IL--10, IL-8/IL-10, and TNF-α /IL-10 were positively correlated with the AGTR1/AGTR2 and AGTR1/MAS1 ratios, respectively. The stimulation of the AGTR2 MAS-receptor and the inhibition of the AGTR1 receptor revealed beneficial effects on the gene expression of inflammatory and tissue remodeling markers. This finding was also present at the protein level. We did not find alterations in iNOS protein concentrations after adding the drugs. The current data showed that tRAS components are expressed in human NP cells and are associated with inflammatory and degenerative processes. Further characterization of the associated pathways is warranted. The findings indicate that tRAS modulation might be a novel therapeutic approach to intervertebral disc disease.

Digital microfluidics (DMF) holds great potential for the alleviation of laboratory procedures in assisted reproductive technologies (ARTs). Electrowetting on dielectric (EWOD) provides dynamic culture conditions in vitro that may better mimic the natural embryo microenvironment. Thus far, EWOD microdevices have been proposed for in vitro gamete and embryo handling in mice and for analyzing the human embryo secretome. This article presents the development of the first microfluidic chip utilizing EWOD technology designed for the manipulation of bovine embryos in vitro. The prototype sustains the cell cycles of embryos manipulated individually on the chips during in vitro culture (IVC). Challenges related to the chip fabrication as well as to its application during bovine embryo IVC in accordance with the adapted on-chip protocol are thoroughly discussed, and future directions for DMF in ARTs are indicated.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

The presence of dark matter, though well established by indirect evidence is yet to be observed directly. Various dark matter detection experiments running for several years have yielded no positive results so far. In view of these negative results, we had earlier proposed alternate models by postulating a minimum gravitational field strength (minimum curvature) and also a minimum acceleration. These postulates led to the modified Newtonian dynamics and modified Newtonian gravity (MONG). The observed flat rotation curves of galaxies had also been accounted for through these postulates. Here we extend these postulates to galaxy clusters and model the dynamical velocity-distance curves for such large-scale structures. The velocity-distance curve of the Virgo cluster, plotted with this model is found to be in accordance with that observed.

Introduction: Anterior cervical discectomy and fusion (ACDF) for cervical disc herniation (CDH) is commonly performed. Specific postoperative complications include dysphagia, dysphonia, cervicalgia, adjacent segment disorder, cage subsidence, and infections. However, interscapular pain is commonly reported by these patients after surgery, although its mechanisms have been not clarified yet. Methods: This retrospective series of 31 patients undergoing ACDF for CDH at a single Academic Hospital. Baseline and postoperative clinical, radiological, and surgical data were analyzed. The linear regression analysis was conducted to identify any factor independently influencing the occurrence rate of postoperative interscapular pain. Results: The mean age was 57.6±10.8 years, and the M:F ratio was 2.1. The preoperative mean VAS-arm was 7.15±0.81 among the 20 patients reporting brachialgia, and the mean VAS-neck was 4.36±1.43 among those 9 patients reporting cervicalgia. At 1 month interscapular pain was still reported by 8 out of the 17 patients who experienced it postoperatively, and it was recovered in all patients after 2 months. The regression analysis showed how the interscapular pain was not directly associated to age(p=0,74), gender(p=0,46), smoking status(p=0,44), diabetes(0,42), preoperative brachialgia(p=0,21) or cervicalgia(p=0,48), symptoms duration(p=0,13), baseline VAS-arm(p=0,11), VAS-neck(p=0,93), or mJOA(p=0,63) scores, or disc height modification(p=0,90). However, the postoperative increase of the mean zygapophyseal joint rims distance was identified as an independent factor in determining interscapular pain (p=0,02). Conclusions: Our study revealed that the onset of interscapular pain following ACDF may be determined by over-distraction of the zygapophyseal joints rim. Then, proper sizing of prosthetic implants could reduce this painful complication.

In ageing tissues, long-lived extracellular matrix (ECM) proteins are susceptible to the accumulation of structural damage due to diverse mechanisms including glycation, oxidation and protease cleavage. Peptide location fingerprinting (PLF) is a new mass spectrometry (MS) analysis technique capable of identifying proteins exhibiting structural differences in complex proteomes. PLF applied to published young and aged intervertebral disc (IVD) MS datasets (posterior, lateral and anterior regions of the annulus fibrosus), identified 268 proteins with age-related structural differences. For several ECM assemblies (collagens I, II and V and aggrecan), these differences were markedly conserved between degeneration-prone (posterior and lateral) and resistant (anterior) regions. Significant differences in peptide yields, observed within collagen I, II and V α-chains (COL1A2, COL2A1, COL5A1), were located within their triple helical regions and/or cleaved C-terminal propeptides, indicating potential accumulation of damage and impaired maintenance in ageing. Several proteins (COL5A1, COL2A1 and aggrecan) also exhibited tissue region (lateral)-specific differences in structure between aged and young, suggesting that some ageing mechanisms may act locally within tissues. This study not only provides evidence of age-related changes in ECM protein structures which are tissue-region specific, but also highlights the ability of PLF to identify potential protein biomarkers of localised tissue remodelling.

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

This study refers to the optimization of a Selective Solar Absorber to improve the Sun-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal collectors. Efficiency has been evaluated by using analytical formula and a numerical thermal model. Both results have been experimentally validated using a commercial absorber in a custom experimental set-up. The optimization procedure aimed at obtaining Selective Solar Absorber is presented and discussed in the case of a metal dielectric multilayer based on Cr2O3 and Ti. The importance of adopting a real spectral emissivity curve to estimate high thermal efficiency at high temperatures in selective solar absorber is outlined. Optimized absorber multilayers can be 8% more efficient than the commercial alternative at 250 °C operating temperatures and up to 27% more efficient at 300 °C. Once the multilayer has been optimized the choice of a very low emissivity substrate such as copper allows to further improve efficiency and to reach stagnation temperature higher than 400 °C without Sun concentration.

The vehicles number continuously growing lead to increasingly intense and congested traffic and it will additionally demand the braking system, and drivers behave more aggressively and as result is required that the braking system to be durable and efficient. For this is necessary the study the braking system behavior in conditions of intense and moderate traffic to increase the safety of traffic participants, respectively to demonstrate the need for more frequent replacement of some braking system elements. Thus, on a vehicle were performed a series of successive tests, through which the degree of wear of the brake pads and discs was monitored periodically and as a result the efficiency evolution of the braking system. The tests were carried out both in laboratory (on dynamometer) and in traffic to establish the efficiency of the braking system according to some parameters considered essential. The experimental tests showed that the recommendations regarding the frequency of replacement of brake pads and disks are inconsistent with their actual wear. Therefore, the aim of this paper is the establishment of the braking system efficiency of an auto-vehicle, subject to testing depending on the auto-vehicle mass, travel speed, distance driven, and braking time, based on experimental on stand and in-traffic tests, according the road safety regulations.

Cervical fusion has been a standard procedure for treating the abnormalities associated with the cervical spine. However, the reliability of anterior cervical discectomy and fusion (ACDF) has become arguable due to its adverse effects on the biomechanics of adjacent segments. One of the drawbacks associated with ACDF is adjacent segment degeneration (ASD) which has served as the base for the development of dynamic stabilization systems (DSS) and total disc replacement (TDR) devices for cervical spine. However, the hybrid surgical technique has also gained popularity recently but their effect on the biomechanics of cervical spine is not well researched. Thus, the objective of this FE study was to draw the comparison among single, bi-level and hybrid surgery with DCI implant with traditional fusion. Reduction in range of motion (ROM) for all the implanted models was observed for all the motions except extension, compared to intact model. The maximum increase in ROM of 42% was observed at C5-C6 level in Hybrid-DCI model. The maximum increase in adjacent segment’s ROM of 8.7% was observed in multilevel fusion model. The maximum von Mises stress in the implant was highest for the multilevel DCI model. Our study also showed that the shape of DCI implant permits flexion/extension relatively more compared to lateral bending and axial rotation.

Non-alcoholic fatty liver (NAFLD) is a metabolic disorder related with a chronic lipid accumulation within the hepatocytes. This disease is the most common liver disorder worldwide and it is estimated that is present in up to 25% of the world's population. However, the real prevalence of this disease and the associated disorders is unknown mainly because reliable and applicable diagnostic tools are lacking. It is known that the level of albumin, a pleiotropic protein synthetized by hepatocytes, is correlated with the correct function of the liver. The development of a complementary tool that allow the direct, sensitive, and label-free monitoring of albumin secretion in hepatocyte cell culture can provide insight about the mechanism and drugs action in NAFLD. With this aim, we have developed a simple integrated plasmonic biosensor based on gold nanogratings from periodic nanostructures present in commercial Blu-ray optical disc. This sensor allows the direct and label-free monitoring of albumin in a 2D fatty liver disease model under flow conditions using highly specific polyclonal antibody. This technology avoids both the amplification and blocking steps showing a limit of detection within pM range (≈ 0.39 ng/mL). Thanks to this technology, we identified the optimal fetal bovine serum (FBS) concentration to maximize the lipid accumulation within the cells. Moreover, we discovered that at third day from lipids challenge, the hepatocytes increased the amount of albumin secreted. These data demonstrate the ability of hepatocytes to respond to the lipid stimulation releasing more albumin. Further investigation needed to unveil the biological significance of that cell behaviour.

In this paper we investigate analytic automorphisms of complex topological vector spaces and their applications to linear and nonlinear transitive operators. We constructed some examples of polynomial automorphisms which show that a natural analogue of the Jacobian Conjecture for infinite dimensional spaces is not true. Also, we prove that any separable Fréchet space supports a transitive analytic operator which is not a polynomial. We found some connections of analytic automorphisms and algebraic bases of symmetric polynomials and applications to hypercyclisity of composition operators.

In this paper, a prototype of an automatic lab on PCB for agarose preparation and electrophoresis is developed. The dimensions of the device are 38×34 mm2 and includes a conductivity sensor for detecting the TAE buffer (Tris-Acetate-EDTA buffer), a microheater for mixing, a NTC thermistor for controlling the temperature, a LDR sensor for measuring the transparency of the mixture, and two electrodes for performing the electrophoresis. The agarose preparation functions are governed by a microcontroller. The device requires a PMMA structure to define the wells of the agarose gel, and to release the electrodes from the agarose. The maximum voltage and current that the system requires are 40 V to perform the electrophoresis, and 1 A for activating the microheater. The chosen temperature for mixing is 80ºC, with a mixing time of 10 min. In addition, the curing time is about 30 min. This device is intended to be integrated as a part of a larger lab on PCB system for DNA amplification and detection. However, it can be used to migrate DNA amplified in conventional thermocyclers. Moreover, the device can be modified for preparing larger agarose gels and performing electrophoresis in an automatic manner.

Organ-on-Chip is a game-changing technology born from the convergence of tissue engineering and microfluidic technology. Organ-on-Chip devices (OoCs) are expected to offer effective solutions to persisting problems in drug development and personalized disease treatments. This opinion paper surveys the current landscape in research, development, application and market opportunities for OoCs to help establishing a global and multi-stakeholder OoC ecosystem. Based on a bibliometric study, a market analysis, expert interviews, and panel discussions held at the ORCHID Vision Workshop (Stuttgart, 23 May 2018), we outline presently unmet needs, key challenges, barriers and perspectives of the field, and finally propose recommendations towards the definition of a comprehensive roadmap that could render OoCs realistic models of human (patho)physiology in the near future.

This research paper contributes to the literature of deterrence theory in general, and in particular with respect to white-collar crime, offering valuable inside by using a unique data set of fraud and violation of trust incidents for Paraguay. Descriptive evidence show a clear and continuous misallocation of funds and human capital, and therefore providing less efficient services for the public. Regression analysis suggests that clearance rate exerts a highly significant effect in deterring fraud but results are not clear for violation of trust incidents. Despite the limitations of available data, results confirm deterrence theory in Paraguay. However, to more than two-thirds of victims, not even the attempt was made to seek justice. As a side-result, it seems that a soft on crime strategy, induced from the former German penal code, has led to an increasing share of pre-trial diversion and therefore enhancing white-collar crimes like fraud and violation of trust due to impunity.

Biometric based access control system acts as a weapon against the challenges for reliable authentication mechanism. Although there are many advantages of biometric system, still it is vulnerable to attacks, which decline its security. This leads to propose a new approach to address these open issues and challenges for biometric data security. Smart card have been already used in past with various degree of success to store biometric credentials. Match-on-card biometric framework locks the biometric data inside the microcontroller of the smart card, which leads to minimal risks if card is lost or stolen. It is fast and accurate, balancing security and convenience by never exchanging user data outside the system of smart card and performs fingerprint enrollment as well as matching within a tamperproof environment of smart card.

Based on a very fast numerical procedure for the determination of the subsurface stress field beneath frictional contacts of axisymmetric elastic bodies under arbitrary 2D oblique loading, the contact mechanical influences of loading parameters and contact profile geometry on the Smith-Watson-Topper (SWT) fatigue crack initiation parameter in elastic fretting contacts with superimposed normal and tangential oscillations are studied in detail. The efficiency of the stress calculation allows for a comprehensive physical analysis of the multi-dimensional parameter space of influencing variables. It is found that a superimposed normal oscillation of the contact can significantly increase or decrease the SWT parameter, depending on the initial phase difference and frequency ratio between the normal and tangential oscillation. Written in proper non-dimensional variables, the rounded flat punch always exhibits smaller values of the SWT parameter, compared to a full paraboloid with the same curvature, while the truncated paraboloid exhibits larger values. A small superimposed profile waviness also significantly increased or decreased the SWT parameter, depending on the amplitude and wave length of the waviness. While both the load protocol and the profile geometry can significantly alter the SWT parameter, the coupling between both influencing factors is weak.

High Vacuum Flat Plate Collectors (HVFPCs) are the only type of Flat Plate Thermal Collectors capable of producing thermal energy for middle-temperature applications (until 180 °C). As the trend of research plans to develop new Selective Solar Absorbers to extend the range of HVFPC application until 250 °C, it is necessary to correctly evaluate the collector efficiency up to such temperature to predict the energy production accurately. We propose an efficiency model for these collectors based on the selective absorber optical properties. The proposed efficiency model explicitly includes the radiative heat exchange with the ambient, which is the main source of thermal losses for evacuated collectors at high temperatures. It also decouples the radiative losses that depend on the optical properties of the absorber adopted from the other thermal losses due to HVFPC architecture. The model has been validated by applying it to MT-Power HVFPC manufactured by TVP-Solar, and it has been used to predict the efficiency and energy production of HVFPC equipped with new, optimized selective solar absorbers developed in recent years.

To verify the authors’ mathematical model for water jet cooling of steel sheet, the previously performed experimental studies of temperature of the test plate in the roller quenching machine (RQM) were used. The calculated data of steel temperature evolution along the RQM length were compared with the readings of thermocouples inserted in the center of the test plate and at its surfaces. The core of the model is the dependence of the temperatures of film, transition and nucleate boiling regimes on the thickness of the oxide scale layer on the cooled surface. It was found that the model correctly takes into account the oxide scale on the sheet surface, flow rates and combinations of the RQM banks used, water temperature and other factors. For all experiments the calculated metal temperature corresponds well to the measured one. In the experiments with interrupted cooling, the calculated temperature plots repeat the characteristic changes in the experimental curves. The main uncertainty in the modeling of cooling in a wide temperature range can be contributed by the random nature of changes in the oxide scale thickness during water cooling. In this regard, the estimated thickness of the oxide scale layer should be considered as the main parameter for adapting the sheet temperature control process. The obtained data confirm the possibility of effective application of the model in the ACS of industrial TMCP (Thermo-Mechanical Controlled Process) systems.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

We emphasize the point that, standard model of cosmology is basically a model of classical general relativity and it seems inevitable to have a revision with reference to quantum model of cosmology. Utmost important point to be noted is that, ‘Spin’ is a basic property of quantum mechanics and ‘rotation’ is a very common experience. In this context, we propose five assumptions in line with Planck mass as the baby universe. We appeal that, 1) Universe can be modeled as a time-reversed black hole (a white hole) with rotation and light speed expansion, and 2) ‘Light speed expanding cosmic space’ can be called as ‘Flat space’. With reference to light speed expansion, if one is willing to re-define cosmic red shift as [z/(1+z)], without considering Lambda cosmology model of matter density fractions, light travel distances can be reproduced with a marginal error of +8.6% at z =1.2, (i.e. traditional light travel distance is 8.6% higher than our estimate), 0% at z = 11.5 and -5.5% at z = 1200.( i.e. traditional light travel distance is 5.5% lower than our estimate). Advantages of our model are, 1) A quantum model of cosmology can be developed with unification of general theory of relativity and quantum mechanics. 2) Tension in estimating the current Hubble parameter can be eliminated via scaled Hawking’s black hole temperature formula with great confidence. 3) Galactic dark matter and visible matter can be studied in a unified manner. 4) Galactic light travel distances can be estimated very easily without matter density fractions. 5) Big Bang and Inflation like non-general relativistic concepts can be relinquished with further study.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

In this work, we investigate the weak deflection angle of light from exact black hole within the non-linear electrodynamics. First we calculate the Gaussian optical curvature using the optical spacetime geometry. With the help of modern geometrical way popularized by Gibbons and Werner, we examine the deflection angle of light from exact black hole. For this desire, we determine the optical Gaussian curvature and execute the Gauss-Bonnet theorem on optical metric and calculate the leading terms of deflection angle in the weak limit approximation. Furthermore, we likewise study the plasma medium's effect on weak gravitational lensing by exact black hole. Hence we expose the effect of the non-linear electrodynamics on the deflection angle in the weak gravitational field.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

Study design :Technical note. Objectives : To present a new unilateral biportal endoscopic technique for lumbar disc herniation without C-arm . Background : Lumbar disc herniation requires surgical intervention when conservative methods fail. Shifts towards minimally invasive percutaneous endoscopic lumbar discectomy, including uniportal and biportal approaches, have been hindered by challenges such as steep learning curves and reliance on radiation-intensive C-arm guidance. Our study introduces the use of standard intraoperative navigation in unilateral biportal endoscopy (UBE) to reduce radiation exposure and increase surgical acuracy. Materials and Methods : A 24-year-old man with low back and bilateral leg pain with gait disturbance was referred to our hospital. He had have conservative treatment for 12 months in another hospital before admission. However, the conservative treatment did not work for him. He had low back pain (VAS 4/10) and bilateral leg pain (VAS 8/10), muscle waekness of bilateral legs (Manual muscle testing ;MMT of extensor hullusis longs 4 4), and numbness of bilateral lower leg. Preoperative lumbar MRI showed L4/5 large central disc herniation. Results: He underwent C-arm free unilateral biportal endoscopic discectomy under the guidance of O-arm navigation. The patient was successfully treated surgically. Postoperative lumbar MRI showed good decompression of dural sac and bilateral L5 nerve roots. MMT and sensory function of both leg had recovered fully on final follow-up at one year. Conclusions/Level of Evidence: The new unilateral biportal endoscopic technique under navigation guidance is useful technique for lumbar disc herniation. This innovative technique proved to be safe, accurate, and minimized radiation exposure for surgeons for the treatment of lumbar intervertebral disc herniation. Level V.

The interplay between Diffuse Idiopathic Skeletal Hyperostosis (DISH) and the gut microbiota represents a compelling area of research, offering insights into the relationship between spinal degenerative diseases and the gut's microbial inhabitants. This comprehensive review seeks to unravel the complex connection, shedding light on its implications for human health and potential therapeutic avenues. A crucial section dives into the world of gut microbiota (GM), exploring its impact on human health, featuring its defining characteristics, and highlighting its role in metabolism, immunomodulation, host interaction, and how its composition changes over time. The subsequent portion delves into the relationship between microbiome composition and pathological bone development, including the link between Intervertebral Disc Degeneration (IDD) and gut inflammation, emphasizing how gut inflammation and GM dysbiosis play pivotal roles. Further dissecting the interconnections, various axes of influence, including the gut-spine axis, gut-bone axis, gut-joint axis, gut-disc axis (specific to DISH), gut-ligament axis, and gut-muscle axis, are discussed. Of particular interest is the section on the impact of GM on DISH-derived pain, addressing a critical aspect of the condition's manifestation. The review discusses the potential of GM modulation as a treatment for DISH, providing hope for therapeutic advancements. Additionally, it highlights the positive impact of lifestyle interventions, such as dietary modifications, sleep optimization, and exercise regimens, in mitigating GM dysbiosis and potentially improving DISH outcomes. Lastly, the intriguing prospect of fecal microbiome transplant and its implications for DISH management is examined, opening new avenues for research and therapeutic interventions. In conclusion, this comprehensive review underscores the intricate interplay between DISH and the gut microbiota, offering a fresh perspective on the impact of GM on spinal degenerative diseases. It emphasizes the potential for innovative treatments, such as GM modulation and lifestyle interventions, and presents fecal microbiome transplant as an exciting area for future exploration.

BackgroundIndex level disc herniation following lumbar spinal decompression is somewhat overlooked as postoperative complication, resulting in return of symptoms. It is proposed that the combination of local instability and degenerated disc is more likely to result in disc herniation. There is no literature comparing post-decompression disc herniation rates between different techniques. This study compares the postoperative disc herniation rates of the "mini-open" laminectomy versus the tubular system decompression.MethodsIn a retrospective comparative study, 563 patient files who underwent primary lumbar spinal decompression, were reviewed and divided into two groups, distinguished by surgical technique. Demographic, clinical, and postoperative data were collected and compared using independent two-tailed t-test and Fisher's exact test with significance set at p<0.05. Primary outcome: comparison of post-decompression surgery, index level, disc herniation occurrence between two surgical techniques.ResultsPostoperative index level disc herniation was significantly lower in the minimally invasive surgery group with 2 cases (0.8%) versus 19 cases (5.8%) in the "mini-open" group [p=0.002]. Disc herniation following single level and multi-level operations were also significantly lower in the minimally invasive group compared with the "mini-open" group (2 versus 11 and 0 versus 8 respectively; p<0.05).ConclusionPostoperative index level disc herniation following lumbar spinal decompression occurs in 3.7% of surgeries. Minimally invasive surgery is found to result in less herniations then "mini-open".

Wire-driven hyper-redundant continuum manipulators are gaining more popularity and finding more applications in industry and in minimally invasive surgery. Unlike traditional rigid link manipulators, continuum robots with a flexible backbone structure are able to work in a highly constrained workspace and in an unstructured environment. However, in spite of a possible wide range of reachability, continuum manipulators have some issues related to payload capacity, accuracy and control. Therefore, in this research, we propose a novel hyper-redundant continuum robot with a passive sliding disc mechanism to improve payload capacity and accuracy. To prove the sliding mechanism concept, we demonstrate a comparison analysis with a conventional non-sliding continuum robot arm in a payload test, a bending test and a reachability test. Moreover, with this novel design, we are proposing robot kinematics and kinetic formulation and simulation results to validate the effectiveness of the sliding disc mechanism.

Worldwide, among older adults, infection is the leading mortality cause; chronic nutritional deficits confer significant mortality risk and increase healthcare costs. The association of the Global Leadership Initiative on Malnutrition (GLIM)-defined malnutrition with infection-related mortality, especially with renal dysfunction in older patients, remains unevaluated. In older patients hospitalized with infection, stratified by renal function, we investigated the association of malnutrition severity with mortality. This single-center, retrospective cohort study of 1220 participants (age ≥65 years) admitted to Aichi Medical University from 2019 to 2020 used a multivariate Cox proportional hazards model to determine the association of GLIM-defined nutritional status (no, moderate, or severe malnutrition) with all-cause mortality. Compared to no malnutrition, moderate and severe malnutrition conferred significantly higher mortality (adjusted hazard ratio [confidence interval ]: 1.00 [reference], 1.76 [1.28-2.42], and 2.44 [1.78-3.33], respectively), with the highest all-cause mortality in malnutrition with a low estimated glomerular filtration rate (eGFR &lt;30 mL/min/1.73m2; 7.35 [4.57-11.8]) compared to no malnutrition and normal eGFR (≥60 mL/min/1.73m2). GLIM-defined malnutrition confers higher all-cause mortality risk in older adults with infection, especially those with renal dysfunction. This information enables the identification of high-risk older patients with infection and targeted clinical management of those with malnutrition, renal dysfunction, and infection.

Oncological changes in the prostate are a common cause of death among elderly men. Malignant cells are difficult to identify at early stages, which are asymptomatic. The patient often seeks medical assistance when the disease has already progressed, and the treatment is less effective. Early diagnosis of prostate cancer (PC) is thus one of the priority tasks of modern urology and healthcare in general. The aim of this study is the detection of microRNAs (miRNAs), which are known to be associated with PC. The detection of the target miRNAs in human plasma samples has been performed with a nanoribbon biosensor system, which was based on "silicon-on-insulator" structures (SOI-NR biosensor). In order to provide biospecific detection of the target miRNAs, the surface of individual nanoribbons has been modified with DNA oligonucleotide probes (oDNA probes), whose nucleotide sequences were complementary to those of the target miRNAs. The high detection sensitivity has been demonstrated with the use of model oDNAs, which are complementary to nanoribbon-immobilized oDNA probes, in buffer solutions. The sensitivity threshold was 1.1 × 10^-17 M. The successful detection of target miRNAs, isolated from real plasma samples of PC patients, has also been demonstrated. We believe that the development of highly sensitive nanotechnology-based biosensors for PC markers is a step towards personalized medicine.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

This paper aims to describe the geometrical structure and explicit expressions of family of finitely parametrized probability densities over smooth manifold $M$. The geometry of family of probability densities on $M$ are inherited from probability densities on Euclidean spaces $\left\{U_\alpha \right\}$ via bundle morphisms, induced by an orientation-preserving diffeomorphisms $\rho_\alpha:U_\alpha \rightarrow M$. Current literature inherits densities on $M$ from tangent spaces via Riemannian exponential map $\exp: T_x M \rightarrow M$; densities on $M$ are defined locally on region where the exponential map is a diffeomorphism. We generalize this approach with an arbitrary orientation-preserving bundle morphism; we show that the dualistic geometry of family of densities on $U_\alpha$ can be inherited to family of densities on $M$. Furthermore, we provide explicit expressions for parametrized probability densities on $\rho_\alpha(U_\alpha) \subset M$. Finally, using the component densities on $\rho_\alpha(U_\alpha)$, we construct parametrized mixture densities on totally bounded subsets of $M$. We provide a description of inherited mixture product dualistic geometry of the family of mixture densities.

In our recently published papers, considering Planck mass based light speed growing black hole universe and scaled Hawking’s black hole temperature formula, we have developed a simple procedure for estimating the current Hubble parameter and current cosmic mass. In addition to that, without considering galactic dark matter, starting from 10 km/sec to 500 km/sec, we have tried to fit the observed galactic flat rotation speeds with a concept of super gravity of galactic baryonic mass. To estimate the equivalent mass of currently hypothecated galactic dark matter, we have introduced a timely increasing cosmological reference mass unit. Its current magnitude seems to be around 200 million solar masses. In this paper, considering 200 million solar masses as a characteristic representation of cosmic weak interaction mass unit, we have developed a simple formula for its estimation. We would like to appeal that, weak interaction boosts the gravity of galaxies in proportion with their virtual dark mass as (galactic baryonic mass)^3/2 / (200 million solar masses)^1/2. With further study- dark matter existence and physical properties can be understood in a theoretical approach.

Study design: Retrospective observational study. Objectives: To evaluate the change in adjacent segment disease (ASD) after hybrid dynamic stabilization with Dynesys-Transition-Optima (DTO). Methods: In 2012–2020, 115 lumbar spinal stenosis patients with spondylolisthesis re-fractory to nonsurgical management received hybrid dynamic stabilization with DTO system in a single medical center from a single neurosurgeon. After excluding those who did not receive L3–L4 dynamic stabilization and L4–L5 transforaminal lumbar interbody fusion fixation and those with incomplete postoperative data (n = 84), the 31 patients studied received follow-up vis-its at 6, 12 and 24 months postoperatively. Radiological assessment applied at the L2–L3, L3–L4 and L5–S1 segments separately included disc height, listhesis distance and angular change while in motion. Implant failure and screw loosening sign were both documented. Results: In the L3–L4 segment, the listhesis distance appeared 1 year after the operation; however, alterations in other segments showed at 6 months. At 2 years, the L3–L4 segment showed significantly less increase in listhesis distance and relatively less disc height reduction than other segments. In motion an-gular change, only the L3–L4 segment had a significant decrease at 2 years. Only the L3–L4 seg-ment maintained negative growth over 2 years in time-dependent assessment of motion angular change. Conclusions: In our study, disc height decreased, listhesis distance increased less and ASD changed later at the index level than the L2–L3 and L5–S1 levels. Angular change was re-duced at the index level while in motion. Although ASD was not significantly prevented, index level degeneration was both minor

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

The gut plays a key role in drug absorption and metabolism of orally ingested drugs. Additionally, characterization of intestinal disease processes are increasingly gaining more attention as gut health is an important contributor to our overall health. The most recent innovation to study intestinal processes in vitro is the development of gut-on-a-chip (GOC) systems. Compared to conventional in vitro models they offer more translational value, and many different GOC models have been presented over the past years. Here, we reflect on the almost unlimited choices in designing and selecting a GOC for preclinical drug (or food) development research. Four components that largely influence the GOC design are highlighted, namely 1) the biological research questions, 2) chip fabrication and materials, 3) tissue engineering, and 4) the environmental and biochemical cues to add or measure in the GOC. Examples are presented of GOC studies in the two major areas of preclinical intestinal research: 1) intestinal absorption and metabolism to study the oral bioavailability of compounds, and 2) treatment-orientated research for intestinal diseases. The last section of this review presents an outlook on the limitations to overcome in order to accelerate preclinical GOC research.

Separation and interpretation of rebellious Circulating Tumor Cells (CTCs) originating from the primary tumor or cancer tissue plays a significant role in diagnostics, cancer progression analyses, suitable medicine exploration, and treatment proficiency examination. Cancer metastasis occurs when CTCs spread throughout the body and invade healthy tissues, leading to new tumors in that area. Although a dramatic rate of deaths begins from spreading CTCs around the body, valuable measures have been made to control their development. However, the first step is separating these harmful cells from the bloodstream and investigating their features. Having examined the characteristics of CTCs as cancer’s main strength, researchers can introduce complementary treatments that can affect cancerous cells without damaging the healthy cells. Therefore, according to their unique characteristics, numerous techniques have been established for continuous and fast separation and sorting of CTCs. Nevertheless, few separators enjoy the efficient performance and appropriate accuracy and can be produced in mass numbers due to the available fabrication equipment. Microfabrication advancements enable separators to combine the advantages of active and passive methods in a small-scale platform for probing individual cells and separation purposes. Reduction in reagents, sample volume, analysis time, and less harmfulness to patients are some of the motivations that encourage researchers to employ microfluidic instruments for CTCs separation from other blood cells over the last two decades. However, microfabrication limitations mean effective separators, and the diagnostic option they provide, are not readily available. Addressing these limitations requires optimizing the design and fabrication of separators such that they are reduced in their size and fabrication cost, while also maintaining high-throughput separating capability. The emergence of the Lab-On-a-Chip (LOC) and then Lab-On-a-CD (LOCD) technologies, having more inherent benefits than conventional microfluidic devices, has created new opportunities and become increasingly widespread in recent years. Evidence suggests that employing single methodologies or integrating approaches without sufficient understanding of potential outcomes is unlikely to result in successful diagnostic results. This paper contributes an extensive review of several separation systems, including fundamental theories and experimental details, and describes detailed operating principles and device performance.

We explore 3D printing modules for self-assembling spacecraft and robots – structure, actuators, electrics. Self-assembly has long been viewed as a highly desirable capability for autonomous construction of large space structures. We review self-assembly in space which focusses on the self-assembly of modules that demonstrate the range of applications. However, self-assembly may be synergised with 3D printing to offer an automated capability from raw material to modules for assembling new spacecraft or habitats. One application of 3D printing is using space debris on-orbit as an in-situ resource - defunct spacecraft may be salvaged as raw material for in-situ construction on demand. The common features of all self-assembling modules are that the modules constitute a structure housing a computer-controlled actuator internally and a reversible latching mechanism externally. We have demonstrated a 3D printed DC electric motor in which the only components that were not 3D printed are the wire coils. We have married our 3D printed motor prototype as an actuated joint between two 3D printed trigon-type panels developed as part of a trigon self-assembling system concept. The trigon concept underlies a modular approach to self-assembling and self-deploying structures. The 3D printed motorised panel system demonstrates that the motor aspect and structural aspects of robotic self-assembling machines are amenable to 3D printing. This has implications for self-assembling systems into modular satellites as a solution to space debris.

The annual demand for fibres continues to rise worldwide. Consequently, more and more fibres must be produced to meet this demand, most of which are melt-spun polymeric man-made fibres. [1] Smooth filaments made of polymers are mainly used for technical applications in industry. For use in clothing or home textiles, for example, a texturing process is used to give the filaments a crimp and thus a feel like that of natural fibres. In this state, they can be processed together with natural fibres and used in textiles. Partially oriented yarns (POY) are of great importance in tex-turing. The yarns are mainly crimped with the help of the so-called false-twist texturing process (FTTP). [2] Since POY accounts for about 60 % of the melt-spun filament yarn produced world-wide, the FTTP is the most important texturing process in the textile industry [3]. In this paper, the main components of false-twist texturing (FTT) machines are explained along with the state of the art and research for each component and its influence on the process. Relevant patents are dis-cussed as well as process optimisation techniques, innovative polymers and yarn types recently used in FTT, followed by a conclusion and an outlook for the process.

Complex blade responses such as a rotating stall or simultaneous resonances are common in modern engines and their observation can be a challenge even for state-of-the-art tip-timing systems and trained operators. This paper analyses forced vibrations of axial compressor blades, measured during the bench tests of the SO-3 turbojet. In relation to earlier studies conducted in ITWL with a small number of sensors, a multichannel tip-timing system let us observe simultaneous responses or higher-order modes. To find possible symptoms of a failure, blade responses in a healthy and unhealthy engine configuration with an inlet blocker were studied. The used analysis methods covered all-blade spectrum and the circumferential fitting of blade deflections to the harmonic oscillator model. The proposed modal solver can track the vibration frequency and adjust the engine order on the fly. That way, synchronous and asynchronous vibrations are observed and analysed together with an extended variant of least squares. The proposed approach helps to avoid common mistakes and saves a lot of work related to configuring the conventional solver.

The Standard Model is not a complete description of reality; it omits the existence of dark matter, dark energy, and an explanation as to why no CP violation has been observed. However, some of these phenomena could be explained through a new force mediated by a new boson. If such a boson were massless it would result in a power law potential and if massive the interaction would be Yukawa-like. A previous experiment employing a micro-mechanical oscillator and a spherical test mass interactions was successful in placing the best limits on a mass-mass Yukawa-like interaction, but the data was never analyzed in the context of a power law. Here that data is analyzed considering a power law for powers n = 1-5 where n is the number of boson exchanges. The results show that the limits obtained through power law analysis of this data are not better than the currently accepted limits. A discussion of an experiment design capable of producing better limits on power law extensions to the Standard Model is presented, and suggests micro mechanical oscillators based experiment remains capable of improving the limits by at least one order of magnitude.

Spiking neural networks (SNNs) promise to perform tasks currently done by classical artificial neural networks (ANNs) faster, in smaller footprints and using less energy. Neuromorphic processors are set out to revolutionize computing at a large scale, but the move to edge-computing applications calls for finely-tuned custom implementations to keep pushing towards more efficient systems. To that end, we have examined the architectural design space for executing spiking neuron models on FPGA platforms, focusing on achieving ultra-low area and power consumption. This work presents an efficient clock-driven spiking neuron architecture used for the implementation of both fully-connected cores and 2D convolutional cores, which rely on deep pipelines for synaptic processing and distributed memory for weight and neuron states. With them, we have developed an accelerator for an SNN version of the LeNet-5 network trained on the MNIST dataset. At around 5.5 slices/neuron and only 348 mW, it is able to use 33% less area and 4 times as less power per neuron as current state-of-the-art implementations while keeping low simulation step times.

This paper sheds light on how crisis management affects post-disaster re-covery. Based on the study of the management of a major environmental disaster, hurricane IRMA, we consider how post-disaster recovery is impacted by crisis management strategies. The perspectives of local stakeholders from the islands of St Martin and St Barthélémy will be shared. We analyze how territories exposed to the same natural phenomena have different outcomes and consider some of the possible reasons. This study reveals underlying risk drivers, to address governance reorganization with a view to better managing socio-economic recovery.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

This paper introduces a novel 3D NoC router that combines buffered and bufferless routing with approximate priority comparison when deflecting flits. Our proposal is a modification of an asymmetrical router that is buffered in the z dimension ports and bufferless in the x and y dimension ports. Flits that request output ports in the x and y dimensions are granted or deflected based on approximate, instead of accurate, priority comparison. Experimental results show that the proposed router, besides effectively combining the advantages of both buffered and bufferless routers, it achieves additional performance and area gains due to the reduced logic required for approximate priority comparison in flit deflections. Experimental results using synthetic and realistic traffic show that the proposed router begins to saturate at a sifnificantly higher injection rate than a bufferless router, but at a slightly lower injection rate than when using accurate priority comparison. Furthermore, the proposed router achieves higher clock frequencies and reduced area compared to the simpler permutation network.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

Drug resistance has become an extremely serious problem worldwide. Antibiotic resistance genes (ARGs) entering the environment with wastewaters promote replenishment of the resistome of natural microbioms. Distribution of several clinically significant ARGs in wastewaters of Rostov-on-Don (Southern Russia), lower reaches of the Don River and natural waters of the neighboring region was investigated. Metagenomic DNA samples isolated from 250 ml of wastewaters or natural waters and 200 mg of surface sediments were used for the study. Identification of the ARGs was carried out with end-point detection PCR. Presence of NDM, OXA-48, CTX-M, VanA, VanB, ErmB, and TetM/TetO genes was detected in urban wastewaters. Samples of wastewater treatment plant (WWTP) sewage were enriched with ARGs in contrast to non-treated wastewaters from the sewage collector. NDM, VanA, ErmB, TetM/TetO genes were found only in wastewaters and were absent in samples of natural waters and surface sediments. Only OXA-48, VanB and CTXM genes were found in natural waters and surface sediments. The described ARGs are quite typical for urban and hospital wastewaters. The target ARGs were detected in the samples connected to the anthropogenous sources of pollution such as Rostov municipal WWTP or livestock enterprise effluents.

We report magnetic silver nanoshells (M AgNSs) that have both magnetic and SERS properties for SERS-based detection. The M AgNSs are composed of hundreds of Fe3O4 nanoparticles for rapid accumulation and bumpy silver shell for sensitive SERS detection by near-infrared laser excitation. The intensity of the SERS signal from the M AgNSs was strong enough to provide single particle-level detection. We obtained much stronger SERS signal intensity from the aggregated M AgNSs than from the non-aggregated AgNSs. 4-Fluorothiophenol was detected at concentrations as low as 1 nM, which corresponds to 0.16 ppb. The limit of detection for tetramethylthiuram disulfide was 10 μM, which corresponds to 3 ppm. The M AgNSs can be used to detect trace amounts of organic molecules using a portable Raman system.

Background: Artificial intelligence can help improve the quality of healthcare by analyzing vast amounts of data and providing more effective and personalized treatment plans. Researchers are working on developing AI-powered solutions that can help improve the outcomes of patients. Objective: To explore the potential of AI in improving healthcare outcomes and patient experience. Results: The study suggests that AI can improve healthcare efficiency and patient outcomes but cannot fully replace human healthcare professionals. AI can assist healthcare professionals in their work, leading to better resource utilization and improved patient care. However, there is still a need for human healthcare professionals to oversee AI systems and provide empathy and personalized care to patients. Conclusion: While there is immense potential for AI in healthcare, it is not yet feasible to replace human healthcare workers. Instead, it should be viewed as a tool that can help improve the efficiency and effectiveness of human healthcare.

Time-series analysis is a widely used technique across various fields and industries, as it helps in understanding, predicting, and forecasting the behavior of data points over time. These fields include but are not limited to finance, economics, healthcare, transportation, etc. In the case of this paper, we have focused on finance. Predicting future values of financial time series offers several benefits. Accurate forecasts can help investors make better decisions about their investments. To predict future values, deep learning algorithms are commonly used since it is an effective method with complex data. In this study, we conduct a study that investigates the use of different data pre-processing techniques on deep learning algorithms in predicting the time series values. To conduct this experimental study, we utilize an open source software, which using long short-term memory technique as the representative deep learning technique, published in github software code repository platform. With this study, we investigate the effects of autoencoder and discrete wavelet transform data pre-processing techniques in time-series prediction. We discuss the details of the experimental study and report our results. The results show that time series prediction (using backtesting methodology) without any data pre-processing leads to 12.6% for mean absolute percentage error. The results also show that, time series prediction with the data preprocessing techniques (Wavelet Transform and Stacked Autoencoder) lead to 3.4%

Background We aimed to compare the retinal, optic disc vascular density (ODVD) values, and acircularity index (AI) of patients with idiopathic macular telangiectasia type 2 (IMT) and healthy individuals using the optical coherence tomography angiography(OCTA) device. Methods The study included 39 patients with IMT and 37 healthy controls. The OCTA findings of the patients and controls were examined. Results The total, parafoveal and perifoveal vascular density of the superficial capillary plexus, choriocapillaris blood flow, inside-disc ODVD, retinal nerve fiber layer (RNFL), and retinal thicknesses were found to be statistically significantly lower and the foveal avascular zone value was statistically significantly higher in the IMT group compared to the control group (p=0.001, p=0.01, p=0.02, p=0.01, p=0.009, p=0.002, p=0.02, respectively).There was a statistically significant negative correlation between best-corrected visual acuity (BCVA) and AI (p=0.02), a statistically significant positive correlation between peripapillary vascular density and BCVA(p=0.04). Conclusion We consider that the lower retinal, choriocapillaris, and ODVD values, retinal and RNFL thicknesses in the patients with IMT compared to the controls were due to vascular damage, remodeling, fibrosis, proliferation, and Müller cell damage. Ellipsoid zone defect, AI, and peripapillary vascular density are important indicators in the evaluation of visual acuity in these patients.

The article presents a methodology for modeling the impact of factors of both on-farm activity and environmental factors on the resulting indicators of an international company. The dataset includes the company's profit, revenue, valuation, share price, and market share from 2012 through 2022. This empirical period is optimal for such a type of modeling. Modeling the impact of carbon emissions factors on the resulting indicators is considered based on complex systems theory. Endogenous model variables include indicators of the development of the international company. Predefined model variables reflect the influence of both the external environment and internal factors on the development indicators of an international company. An approach of picture fuzzy rough sets based on time series of endogenous and exogenous variables can provide an opportunity to analyze and consider the consequences of feedback changes in the systems of which they are a part. Based on the results of the analysis of the model construction, it is concluded that picture fuzzy rough sets can be an excellent way to model interdependent social processes.

Isothermal Nucleic Acid Amplification based-Lateral Flow Testing (INAA-LFT) has emerged as a robust technique for on-site pathogen detection, providing a visible indication of pathogen nucleic acid amplification that rivals or even surpasses the sensitivity of real-time quantitative PCR. The isothermal nature of INAA-LFT ensures consistent conditions for nucleic acid amplification, establishing it as a crucial technology for rapid on-site pathogen detection. However, despite its considerable promise, the widespread application of isothermal INAA amplification-based lateral flow testing faces several challenges. This review provides an overview of the INAA-LFT procedure, highlighting its advancements in detecting plant viruses. Moreover, the review underscores the imperative to address existing limitations and emphasizes ongoing research efforts dedicated to enhancing the applicability and performance of this technology in the realm of rapid on-site testing.

Recent literature has seen a rapid expansion in the reference to front-end forensics as an indication of the untapped value of forensic science. While some of these contributions have centered on development of forensic intelligence from a single area of investigation, others call for a more fundamental change in the relationship between crime laboratories and policing, particularly relating early laboratory analysis with big datasets to provide leads to investigators. We highlight several recently implemented tactical strategies of crime laboratories that contribute to the body of forensic intelligence. Beyond the scientific gains from these tactical applications, the corresponding details on associated efficiencies, costs, time savings, and quality improvements offer insights towards patterns of success for the community of crime laboratories. Further details expand an interpretation of what constitutes success with an eye on the contributions of the crime laboratory towards public health, safety, and protection of the innocent in addition to societal gains from conviction of the guilty. The economic interpretation of the value provided by the forensic laboratory assists in the cost-benefit review of strategic and tactical decisions and supports the justification for laboratory public funding with measures of the return on investment from public support of the forensic laboratory