This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

The wind industry is looking for ways to accurately predict the reliability and availability of newly installed wind turbines. Failure modes, effects and criticality analysis (FMECA) is a technique utilized for determining the critical subsystems of wind turbines. There are several studies which applied FMECA for wind turbines in the literature, but no studies so far have considered different weather conditions or climatic regions. Furthermore, various design types of wind turbines have been analyzed applying FMECA but no study so far has applied FMECA to compare the reliability of geared and direct-drive wind turbines. We propose to fill these gaps by using Koppen-Geiger climatic regions and two different turbine models of direct-drive and geared-drive concepts. A case study is applied on German wind farms utilizing the WMEP database which contains wind turbine failure data from 1989 to 2008. This proposed methodology increases the accuracy of reliability and availability predictions and compares different wind turbine design types and eliminates underestimation of impacts of different weather conditions.

Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum, and energy balances in each engine's component. The solution code has been developed in Matlab-Simulink using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

Wind power output is highly dependent on the wind speed at the selected site, therefore wind-speed distribution modeling is the most important step in the assessment of wind energy potential. This study aims at accurate evaluation of onshore wind energy potential in seven coastal cities in the south of Iran. Six Probability Distribution Functions (PDFs) were examined over representative stations. It has been deduced that the Weibull function, which was the most used PDF in similar studies, was only applicable to one station. Here, Gamma offered the best fit for three stations and for the other ones, Generalized Extreme Value (GEV) performed better. Considering the ranking of six examined PDFs and the simplicity of Gamma, it was identified as the effective function in the southern coasts of Iran bearing in mind the geographic distribution of stations. Besides, six turbine power curve functions were contributed to investigate the capacity factor. That was very important, as using only one function could cause under- or over-estimation. Then, stations were classified based on the National Renewable Energy Laboratory system. Last but not least, examining a range of wind turbines enabled scholars to extend this study into the practice and prioritize development of stations considering budget limits.

Aquatic animals have unique physiological mechanisms to absorb and retain minerals from their diets and water. Research and development in the area of mineral nutrition of farmed fish and crustaceans have been relatively slow and major gaps exist in the knowledge of trace element requirements, physiological functions and bioavailability from feed ingredients. Quantitative dietary requirements have been reported for three macroelements (calcium, phosphorus and magnesium) and six trace minerals (zinc, iron, copper, manganese, iodine and selenium) for selected fish species. Mineral deficiency signs in fish include reduced bone mineralization, anorexia, lens cataracts (zinc), skeletal deformities (phosphorus, magnesium, zinc), fin erosion (copper, zinc), nephrocalcinosis (magnesium deficiency, selenium toxicity), thyroid hyperplasia (iodine), muscular dystrophy (selenium) and hypochromic microcytic anaemia (iron). An excessive intake of minerals from either diet or gill uptake causes toxicity and therefore a fine balance between mineral deficiency and toxicity is vital for aquatic organisms to maintain their homeostasis either through increased absorption or excretion. Release of minerals from uneaten or undigested feed and from urinary excretion can cause eutrophication of natural waters, which requires additional consideration in feed formulation. The current knowledge in mineral nutrition of fish is briefly reviewed.

In order to improve the performance of the draft tube in hydraulic turbine, a multi–objective optimization method for the draft tube is developed by combining the design of experiment (DOE), the radial basis function (RBF) and the non–dominated sorting genetic algorithm (NSGA–II) in this paper. The geometrical design variables of the median section in the draft tube and the cross section in its exit diffuser are considered as design parameters in this optimization, which objective function is to maximize the pressure recovery factor (Cp) and minimize the energy loss coefficient (ζ). The limited numbers of design matrix required for the shape optimization of the draft tube is generated by optimal Latin hypercube (OLH) method of the DOE technique, of which performances are evaluated through computational fluid dynamic (CFD) numerical simulation. For reducing of the computational consumption, the approximate model is used based on the RBF. The Pareto optimal solutions are finally performed using the NSGA–II for obtaining the best geometrical parameters of the draft tube. The optimization result of the draft tube shows a marked performance improvement over the original, which verifies the theoretical validity and feasibility of the proposed method in this paper.

The global energy crisis has lead researchers explore other sources of energy like wind, resulting in a wide acceptance of wind turbines. Vertical axis wind turbines (VAWT) more suitable for small scale application in urban conditions than their horizontal-axis counterparts. A Helical bladed VAWT would reduce the ripple effect when compared to Straight bladed VAWT. The effect of the blade helix angle on the aerodynamic performance of VAWT using 3D numerical simulations is studied. Turbulence modelled using 4-Equation transition SST k-w model. Three different helix angles of 60, 90 and 120 of a 3 bladed VAWT operating across different tip speed ratios were studied. The 60 helical bladed VAWT was found to perform better than all other helical bladed and straight bladed VAWT. Standard deviation of the moment coefficient generated by a blade plotted against 360 of azimuth rotation revealed that the ripple effect on the shaft produced by cyclic loading of the straight blade is considerably reduced upon introduction of helix angle, with 120 helical blade giving lowest standard deviation. The analysis has been done for the percentage of power generated by each quartile of flow and the contribution of each section of the blade. A comparative study was also conducted between different helical bladed VAWT and straight bladed VAWT. Flow feature analysis also revealed the reasons behind secondary peaks and the performance improvement when tip speed ratio increases. Wake structure analysis and flow contours were also studied for a better understanding of the flow field.

Timely detection of surface damages on wind turbine blades is imperative for minimising downtime and avoiding possible catastrophic structural failures. With recent advances in drone technology, a large number of high-resolution images of wind turbines are routinely acquired and subsequently analysed by experts to identify imminent damages. Automated analysis of these inspection images with the help of machine learning algorithms can reduce the inspection cost, thereby reducing the overall maintenance cost arising from the manual labour involved. In this work, we develop a deep learning based automated damage suggestion system for subsequent analysis of drone inspection images. Experimental results demonstrate that the proposed approach could achieve almost human level precision in terms of suggested damage location and types on wind turbine blades. We further demonstrate that for relatively small training sets advanced data augmentation during deep learning training can better generalise the trained model providing a significant gain in precision.

Tidal stream energy is a low carbon energy source. Tidal stream turbines operate in a turbulent environment, and the effect of the structure between the turbine and seabed on this environment is not fully understood. An experimental study using 1:72 scale models based on a commercial turbine design was carried out to study the support structure influence on turbulence intensity around turbine blades. The study was conducted using the wave-current tank at LABIMA, University of Florence. A realistic flow environment (ambient turbulent intensity = 11%) was established. Turbulence intensity was measured upstream and downstream of a turbine mounted on two different support structures (one resembling a commercial design, the other the same with an additional vertical element), in order to quantify any variation in turbulence and performance between the support structures. Turbine drive power was used to calculate power generation. Acoustic Doppler Velocimetry was used to record and calculate upstream and downstream turbulence intensity. In otherwise identical conditions, performance variation of only 4% was observed between two support structures. Turbulent intensity at 1, 3 and 5 blade diameters, both upstream and downstream, showed variation up to 21% between the two cases. The additional turbulent structures generated by the additional element of the second support structure appears to cause this effect, and the upstream propagation of turbulent intensity is believed to be permitted by surface waves. This result is significant for the prediction of turbine array performance.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

A turbomachinery is essential part in the power generation cycle. But, it is main noise source to annoy workers and users and to make environmental problem. Thus it is important to reduce this noise for operating the power generation cycle. This noise is created by flow instability on rotor blade trailing edge. An airfoil that becomes a section of a rotor blade of a rotating machine is manufactured as a blunt trailing edge (TE) with a round or flatback shape rather than the ideal sharp TE shape for the purposes of producibility and durability. This increases the tonal noise and flow-induced vibration at low frequency owing to vortex shedding behind TE when compared with a sharp TE. In order to overcome this problem, this study investigates the oblique TE shape using numerical simulation. In order to do so, the flow was simulated using large eddy simulation (LES) and the noise was analysed by acoustic analogy coupled with LES result. Once the simulation results were verified using the flatback airfoil measurements of Sandia National Laboratories, numerical prediction was performed for airfoils modified to have oblique trailing edge angles of 60°, 45°, and 30° to analyse the flow and noise characteristics. From the simulation results for an airfoil having an oblique TE, it could be seen that the vortex shedding frequency moves in accordance with the oblique angle and that the vortex shedding noise characteristics change according to this angle when compared to the flatback TE airfoil. Therefore, it is considered that modifying the flatback TE airfoil to have an appropriate oblique angle can reduce noise and change the tonal frequency to a bandwidth that is suitable for mechanical systems.

Gas Path Analysis and matching turbine engine models to experimental data are inverse problems of mathematical modelling which are characterized by parametric uncertainty. This results from the fact that the number of measured parameters is significantly lower than the number of components’ performance parameters needed to describe the real engine. In these conditions, even small measurement errors can result in a high variation of results, and obtained efficiency, loss factors etc. can appear out of the physical range. The current methods of engine model identification have developed considerably to provide stable, precise and physically adequate solutions. Presented in this work is an estimation method of engine components’ parameters based on multi-criteria identification which provides stable estimations of parameters and their confidence intervals with the known measurement errors. A priori information about the engine, its parameters and performance is used directly in the regularised identification procedure. The mathematical basis for this approach is the fuzzy sets theory. Forming objective functions and scalar convolutions synthesis of these functions is used to estimate gas-path components’ parameters. A comparison of the proposed approach with traditional methods showed that its main advantage is high stability of estimation in the parametric uncertainty conditions. Regularization reduces scattering, excludes incorrect solutions which do not correspond to a priori assumptions, and also helps to implement the Gas Path Analysis at the limited number of measured parameters. The method can be used for matching thermodynamic models to experimental data, Gas Path Analysis and also adapting dynamic models for the needs of the engine control system.

Nacelle-based Doppler wind lidars have shown promising capabilities to assess power performance, detect yaw misalignment or perform feed-forward control. The power curve application requires uncertainty assessment. Traceable measurements and uncertainties of nacelle-based wind lidars can be obtained through a methodology applicable to any type of existing and upcoming nacelle lidar technology. The generic methodology consists in calibrating all the inputs of the wind field reconstruction algorithms of a lidar. These inputs are the line-of-sight velocity and the beam position, provided by the geometry of the scanning trajectory and the lidar inclination. The line-of-sight velocity is calibrated in atmospheric conditions by comparing it to a reference quantity based on classic instrumentation such as cup anemometers and wind vanes. The generic methodology was tested on two commercially developed lidars, one continuous wave and one pulsed systems, and provides consistent calibration results: linear regressions show a difference of ∼ 0.5 % between the lidar-measured and reference line-of-sight velocities. A comprehensive uncertainty procedure propagates the reference uncertainty to the lidar measurements. At a coverage factor of two, the estimated line-of-sight velocity uncertainty ranges from 3.2 % at 3 m s⁻¹ to 1.9 % at 16 m s⁻¹. Most of the line-of-sight velocity uncertainty originates from the reference: the cup anemometer uncertainty accounts for ∼ 90 % of the total uncertainty. The propagation of uncertainties to lidar-reconstructed wind characteristics can use analytical methods in simple cases, which we demonstrate through the example of a two-beam system. The newly developed calibration methodology allows robust evaluation of a nacelle lidar’s performance and uncertainties to be established in order to further be used for various wind turbines’ applications in confidence.

A numerical study of the flow over a NACA aerofoil is presented in this paper. The numerical simulations are achieved with the computer code CFX and the computational domain is created by the computer tool ANSYS ICEM CFD. The CFX code is based on the finite volume method to solve the equations of mass, momentum and energy. The purpose of this paper is to determine the pressure distribution, flow patterns and the forces acting on the airfoil. Effects of the attack angle and Reynolds number on the velocity and pressure distribution, on the lift and drag coefficients are also explored.

Cellular agriculture is defined as the production of agricultural products from cell cultures rather than from whole plants or animals. With growing interest in cellular agriculture as a means to address the public health, environmental, and animal welfare challenges of animal agriculture, the concept of producing seafood from fish cell- and tissue-cultures is emerging as a means to address similar challenges with industrial aquaculture systems and marine capture. Cell-based seafood - as opposed to animal-based seafood - can combine developments in biomedical engineering with modern aquaculture techniques. Biomedical engineering developments such as closed-system bioreactor production of land animal cells create a basis for large scale production of marine animal cells. Aquaculture techniques such as genetic modification and closed system aquaculture have achieved marked gains in production that can pave the way for innovations in cell-based seafood production. Here, we present the current state of innovation relevant to the development of cell-based seafood across multiple species as well as specific opportunities and challenges that exist for advancing this science. The authors find that the physiological properties of fish cell- and tissue- culture may be uniquely suited to cultivation in vitro. These physiological properties, including hypoxia tolerance, high buffering capacity, and low-temperature growth conditions, make marine cell culture an attractive opportunity for scale production of cell-based seafood; perhaps even more so than mammalian and avian cell cultures for cell-based meats. This, coupled with the unique capabilities of crustacean tissue-friendly scaffolding such as chitosan, a common seafood waste product and mushroom derivative, presents great promise for cell-based seafood production via bioreactor cultivation. To become fully realized, cell-based seafood research will require more understanding of fish muscle culture and cultivation; more investigation into serum-free media formulations optimized for fish cell culture; and bioreactor designs tuned to the needs of fish cells for large scale production.

Renewable energy sources will play a central role in the sustainable energy systems of the future. Scenario analyses of such hypothesized energy systems require sound knowledge of the techno-economic potential of renewable energy technologies. Although there have been various studies concerning the potential of offshore wind energy, higher spatial resolution, as well as the future design concepts of offshore wind turbines, has not yet been addressed in sufficient detail. Here, we aim to overcome this gap by applying a high spatial resolution to the three main aspects of offshore wind potential analysis, namely ocean suitability, the simulation of wind turbines and cost estimation. A set of constraints is determined that reveal the available areas for turbine placement across Europe’s maritime boundaries. Then, turbine designs specific to each location are selected by identifying turbines with the cheapest levelized cost of electricity (LCOE), restricted to capacities, hub heights and rotor diameters of between 3-20 MW, 80-200 m and 80-280 m, respectively. Ocean eligibility and turbine design are then combined to distribute turbines across the available areas. Finally, LCOE trends are calculated from the individual turbine costs, as well as the corresponding capacity factor obtained by hourly simulation with wind speeds from 1980 to 2017. The results of cost-optimal turbine design reveal that the overall potential for offshore wind energy across Europe will constitute nearly 8.6 TW and 40.0 PWh at roughly 7 €_ct kWh^-1 average LCOE by 2050. Averaged design parameters at national level are provided in an appendix.

Anomaly detection plays a significant role in helping gas turbines run reliably and economically. Considering collective anomalous data and both sensitivity and robustness of the anomaly detection model, a sequential symbolic anomaly detection method is proposed and applied to the gas turbine fuel system. A structural Finite State Machine is to evaluate posterior probabilities of observing symbolic sequences and most probable state sequences they may locate. Hence an estimating based model and a decoding based model are used to identify anomalies in two different ways. Experimental results indicates that these two models have both ideal performance overall, and estimating based model has a strong ability in robustness, while decoding based model has a strong ability in accuracy, particularly in a certain range of length of sequence. Therefore, the proposed method can well facilitate existing symbolic dynamic analysis based anomaly detection methods especially in gas turbine domain.

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

After a local pollution control plant significantly reduced phosphorus loading into a phytoplankton-dominated tributary of the Potomac River in the early 1980’s, water quality and biological communities were monitored bi-weekly from April-September. After a 10-year time-lag, submerged aquatic vegetation (SAV), once abundant in this freshwater tidal embayment, returned to the area in 1993. After additional reductions in nitrogen load starting in 2000, the system completely switched to a SAV-dominated state in 2005. Fish abundance didn’t change during these distinct phase changes, but the fish community structure did. Increases in SAV provided refuge and additional spawning substrate for species with adhesive eggs such as Banded Killifish (Fundulus diaphanus), which is now the most abundant species in the embayment. Other changes seen were a decrease in the relative contribution of open water dwelling species such as White Perch (Morone americana), and an increase of visual predators such as Largemouth Bass (Micropterus salmoides). The 30-year record of data from this Potomac River tributary has revealed many important long-term trends that validate the effectiveness of initiatives to improve water treatment, and will aid in the continued management of the watershed and point source inputs.

Computational fluid dynamics is used to study the impact of the support structure of a tidal turbine on performance and the downstream wake characteristics. A high-fidelity computational model of a dual rotor, contra-rotating tidal turbine in a large channel domain is presented, with turbulence modelled using large eddy simulation. Actuator lines represent the turbine blades, permitting the analysis of transient flow features and turbine diagnostics. The following four cases are considered: the flow in an unexploited, empty channel; flow in a channel containing the rotors; flow in a channel containing the support structure; and flow in a channel with both rotors and support structure. The results indicate that the support structure contributes significantly to the behaviour of the turbine and to turbulence levels downstream, even when the rotors are upstream. This implies that inclusion of the turbine structure, or some parametrisation thereof, is a prerequisite for the realistic prediction of turbine performance and reliability, particularly for array layouts where wake effects become significant.

Full-order state-space models represent the starting point for the development of advanced control methods for wind turbine systems (WTSs). Regarding existing control-oriented WTS models, two research gaps must be noted: (i) There exists no full-order WTS model in form of one overall ordinary differential equation that considers all dynamical effects which significantly influence the electrical power output; (ii) all existing reduced-order WTS models are subject to rather arbitrary simplifications and are not validated against a full-order model. Therefore, in this paper, two full-order nonlinear state-space models (of 11th and 9th-order in the (a, b, c)- and (d, q)-reference frame, resp.) for variable-speed variable-pitch permanent magnet synchronous generator WTSs are derived. The full-order models cover all relevant dynamical effects with significant impact on the system’s power output, including the switching behavior of the power electronic devices. Based on the full-order models, by a step-by-step model reduction procedure, two reduced-order WTS models are deduced: A non-switching (averaging) 7th-order WTS model and a non-switching 3rd-order WTS model. Comparative simulation results reveal that all models capture the dominant system dynamics properly. The full-order models allow for a detailed analysis covering the high frequency oscillations in the instantaneous power output due to the switching in the power converters. The reduced-order models provide a time-averaged instantaneous power output (which still correctly reflects the energy produced by the WTS) and come with a drastically reduced complexity making those models appropriate for large-scale power grid controller design.

Hill stream loaches are a group of fish that inhabit fast flowing shallow freshwater. The family has radiated over Asia. For some species their range is limited to single catchments; they provide an excellent example of biogeographical speciation on multiple scales. Hill stream loaches have a range of adaptations which help them exploit environments where competitors and predators would be washed away. They have streamlined bodies and keeled scales reminiscent of Mako sharks and potentially many other as yet undiscovered drag reducing features. They adhere to rocks, crawl over shallow films of water, glide over hard surfaces using ground effects and launch into currents to attack prey or evade predation. They offer a test of modern approaches to organismal biology and a broad range of biomimetic potential. In this paper we analyse what behaviour is associated with their physical adaptations and how this might relate to their evolution and radiation. Our intent here is to review information that is presently available but also to derive new insight through combination and statistical analysis of existing material. We also use our own observations and critically argue several contradictory, or poorly supported assertions in the existing scientific literature. Our conclusion is that, although extensively studied, there remain major gaps in knowledge about their organismal biology. We summarise the research opportunities in the form of hypotheses that are worth testing.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

Fish oil rich in polyunsaturated omega-3 fatty acids is extracted in high yield from anchovy filleting waste using d-limonene as green biosolvent in a simple solid-liquid extraction performed by mechanically stirring and maceration followed by limonene removal via evaporation under reduced pressure. As limonene is renewably obtained from waste orange peel, this protocol establishes a circular bioeconomy method to obtain valued omega-3 extracts from biowaste available worldwide in several million t/year amount. The method closes the materials cycle and opens the route to full valorisation of an important biological resource so far mostly discarded as waste. Significant economic opportunities benefiting local communities, the ecosystem and public health are anticipated.

The Betz limit sets a theoretical upper limit for the power production by turbines expressed as a maximum power coefficient of 16/27. Betz’s theory is accurate and it is based on the calculation of kinetic energy.

The current need to develop sustainable power sources has led to the development of ocean-based conversion systems. Wells turbine is a widely used converter in such systems which suffers from a lack of operational range and power production capacity under operational conditions. The profile named IFS which is concave in the post-mid-chord region, can produce significantly larger lift forces and show better separation behavior than the NACA profiles. In the present study, we tested this profile for the first time in a Wells turbine. The performance of six different blade designs with IFS and NACA profiles were evaluated and compared using a validated computational fluid dynamic model. Although the substitution of the NACA profile with the IFS profile in all cases increased the torque generated, the most efficient power generation and the largest efficient range were achieved in the design with varying thickness from the hub with a 0.15 thickness ratio reaching to the ratio of 0.2 at the tip. The operational span of this design with the IFS profile was 24.1% greater and the maximum torque generation was 71% higher than the case with the NACA profile. Therefore, the use of the IFS profile is suggested for further study and practical trials.

Wind turbine plants are complex dynamic and uncertain processes driven by stochastic inputs and disturbances, as well as different loads represented by gyroscopic, centrifugal, and gravitational forces. Moreover, as their aerodynamic models are nonlinear, both modelling and control become challenging problems. On one hand, high-fidelity simulators should contain different parameters and variables in order to accurately describe the main dynamic system behaviour. Therefore, the development of modelling and control for wind turbine systems should consider these complexity aspects. On the other hand, these control solutions have to include the main wind turbine dynamic characteristics without becoming too complicated. The main point of this paper is thus to provide two practical examples of development of robust control strategies when applied to a simulated wind turbine plant. Experiments with the wind turbine simulator and the Monte–Carlo tools represent the instruments for assessing the robustness and reliability aspects of the developed control methodologies when the model-reality mismatch and measurement errors are also considered. Advantages and drawbacks of these regulation methods are also highlighted with respect to different control strategies via proper performance metrics.

Wind energy is becoming an essential source of power for countries which have the aim to reduce greenhouse gases emission and mitigate the effects of global warming. The Wind Turbines (WTs) installed around the globe is increasing significantly every year. The dramatic increase in wind power has encountered quite a few challenges, among which the major issues are availability and reliability. The unexpected failure in WTs Gearbox (GB) ultimately increases the Operation and Maintenance (O&M) cost. The identification of faults in the earlier stages before it turns to catastrophic damage to other components of WT is crucial. This research deals with the prediction of WT failures by using a Supervisory Control and Data Acquisition (SCADA) system. The main aim is to forecast the temperature of the WTs GB to predict the impending overheating of the GB at an early stage. The earlier prediction will help to optimize the maintenance period and to save maintenance expenses and, even more important, generate warnings in due time to avoid major damages or even technical disasters. In the proposed method we compared six different machine learning (ML) models based on error and accuracy of prediction. The bagging regressor is the best ML model, which results in the mean square error of 0.33 and R of 99.8 on training data. The bagging regressor is then used to predict the fault in the WT GB, which detected the anomalous behavior of WT GB 59 days earlier than the actual failure. This model also detects the extremely unusual behavior of the GB 9 days earlier than a complete failure.

More than 800 million tons of fish are utilizing in a year and 25-30% become waste. The waste amount is beneficial source for extraction of collagen. But procedure of extraction is still to be optimized. The current study was designed to extract collagen from fish through fish waste fermentation under various conditions. For collagen extraction we did lactic acid fermentation in which yogurt and Dough bacteria was added with fish sample and placed it in incubator at 30ºC for one month. In yogurt and dough culture have at least 10 type of lactic acid bacterial species. After every week we check PH of each sample and take soup of that sample. After centrifugation of that sample’s TCA (Trichloroacetic acid) precipitation was done of yogurt and dough sample and kept at -20ºC. then did SDS-PAGE) using 6% resolving and 5% stacking gel of already stored sample. Then HaCaT cells (1 × 10⁴ cells/well) were cultured in 96-well flat-bottom culture plates and treated with appropriate doses of FFCP (fermented fish collagen peptide) for 24 and 48 hours.The SDS-PAGE revealed that the collagen protein of fish had doublet pattern for α1 and α2 chains at corresponding to 145 kDa and 132 kDa respectively. The density for α1 twice as compared to α2. Our result agrees that The fish collagen consists mostly of α-chain as well as little amount of inter and intra molecular cross-linked components of α-chains; b (dimmer) and c (trimer). Different biochemical tests were done for identification of lactic acid bacteria catalase positive, citrate positive, urease negative. Our fermented fish collagen and peptides mixture were test for cellular cytotoxicity and proliferative effect on HaCaT cells. Current result shows that fermented extracted collagen are nontoxic and induce the proliferation of HaCaT cells. Current study is supported by various studies that revealed the medical application of fish extracted collagen as underline.

Aerodynamic performance of a floating offshore wind turbine (FOWT) is significantly influenced by platform surging motions. Accurate prediction of the unsteady aerodynamic loads is imperative for determining the fatigue life, ultimate loads on key components such as FOWT rotor blades, gearbox and power converter. The current study examines the predictions of numerical codes by comparing with unsteady experimental results of a scaled floating wind turbine rotor. The influence of platform surge amplitude together with the tip speed ratio on the unsteady aerodynamic loading has been simulated through unsteady CFD. It is shown that the unsteady aerodynamic loads of FOWT are highly sensitive to the changes in frequency and amplitude of the platform motion. Also, the surging motion significantly influences the windmill operating state due to strong flow interaction between the rotating blades and generated blade-tip vortices. Almost in all frequencies and amplitudes, CFD, LR-BEM and LR-uBEM predictions of mean thrust shows a good correlation with experimental results.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

This study aimed to enhance a micro hydroelectric generator system driven by free-flow vortex and to compare efficiency of Propeller and Crossflow turbines. Series of turbines in each type were designed and tested at water-flowrate of 0.02 m3/s. The turbine housing has 1 meter in diameter and 0.5-meter height with 2 meters outlet drain at the bottom. The best efficiency extracted from Crossflow turbines with the same height (0.3 meter) but different in diameter (0.4, 0.5, 0.6, and 0.7 meter) and numbers of blade (12, 18, 24, 30, and 23) was from an 18 blades turbine at 23.01% of efficiency. The best efficiency extracted from Propeller turbines with 5 blades was from a 0.4-meter-high turbine with a diameter of 0.7 meter at 13.92% of efficiency. There were 12 Propeller turbines designed in this study. They were different in height (0.2, 0.3, and 0.4 meter) and, in each height, 0.4, 0.5, 0.6, and 0.7 of diameter was applied. The result revealed that Cross Flow turbine had more efficiency to the system than Propeller turbine (9.09%) at the water-flowrate of 0.02 m3/s

The concept of Design Fatigue Factors (DFFs) was introduced for providing desired level of safety in structural fatigue design, often associated with damage calculated from S-N curves. Calculation of fatigue damage from S-N curves can be affected by multiple factors, e.g. types of weld class, corrosion condition, loading conditions, stress concentration on different geometries etc. Each of them can be subject to different level of uncertainties. This study intends to recalibrate the DFFs from a detailed reliability analysis by investigating the probabilistic models derived from the database of S-N curves that has been most frequently used in offshore wind industry. The results of such study indicate that the DFFs can be reduced substantially for the corrosive environmental fatigue models from current standards to the same level of target reliability.

This paper is concerned with bump-less transfer of parametrized disturbance observer based controller (DOBC) with Individual Pitch Control (IPC) strategy for full load operation of wind turbine. Aerodynamic cyclic loads are reduced by tuning multivariable DOBC with the objective to reduce output power fluctuation, tower oscillation and drive-train torsion. Furthermore tower shadow and wind shear effect are also mitigated using parametrized controller. A scheduling mechanism between two DOBC is developed and tested on Fatigue, Aerodynamics, Structures, and Turbulence ( FAST) code model of National Renewable Energy Laboratory (NREL)’s 5 MW wind turbine. The closed-loop system performance is assessed by comparing the simulation results of proposed controller with a fixed gain and Linear Parameter Varying (LPV) DOBC with Collective Pitch Control (CPC) for full load operation. It is tested with step changing wind to see the behavior of the system under step change with wind shear and tower shadow (cyclic load) effects. Also turbulent wind is applied to see the smooth transition of the controllers. It can be concluded from the results that the proposed parametrized control DOBC with IPC shows smooth transition from one controller to another by interpolation. Moreover fatigue of the gear and tower due to wind shear and tower shadow effects are reduced considerably by the proposed controller as compared to collective pitch control.

Monin-Obukhov similarity theory (MOST) overestimates wind shear in some atmospheric stable conditions, i.e. Richardson number $R_f<0.25$. The overestimated wind shear that leads to an under-predicted friction wind speed and a lower ambient turbulence intensity for a given hub-height reference wind speed and a given roughness length, could influence wake modeling of a wind turbine. This work investigates the side effects of the breakdown of MOST on wake modeling under stable conditions and makes some modifications to the flow similarity functions to eliminate these side effects. Based on a field measurement in a wind farm, we firstly show that MOST predicts a larger wind shear for the atmospheric stability parameter $\zeta>0.1$ and proposes new flow similarity functions without constraining $R_f$ to limit the overestimated wind shear by MOST. Next, different turbulence models based on MOST and a modified one based on the new similarity functions are investigated through numerical simulations. These turbulence models are combined with the actuator disk model (AD) and Reynolds-averaged Navier–Stokes equations (RANS) to model wind turbine wakes under stable conditions. As compared to measurements, numerical results show that turbulence models based on MOST result in larger wake deficits and slower wake recovery rate with a square root of the mean-squared-error (RSME) of wake deficit in the range of 0.07-0.18. This overestimated wake effect is improved by applying the new similarity functions and the RSME of wake deficit is averagely reduced by 0.05. Finally, we check the role of the under-predicted turbulence intensity playing in the larger wake deficit predicted by models based MOST. Additional numerical simulations using the modified turbulence model are carried out, in which the roughness length is reduced to impose a hub-height ambient turbulence intensity equivalent to the MOST case. Simulation results show that reducing turbulence intensity enhances wake effects, however, it cannot reproduce the large wake deficit predicted by models based on MOST, which suggests that the overestimated wake effect by MOST could be also related to the overestimated wind shear.

This paper presents findings of a study on continuous feed-in management and continuous synthetic inertia contribution with wind turbines. A realistic case study, based on real measurements, is outlined. A wind turbine feeds into a weak feeder, such that its power has to be adapted to the permissible loading of this feeder. At the same time the wind turbine is to provide inertia to the grid by applying the previously published variable inertia constant controller. It is discussed that optimal grid utilisation and simultaneous inertia contribution are mandatory for the frequency control in power systems that are heavily penetrated with renewable energies. The study shows that continuous feed-in management can be combined well with continuous inertia provision. There are hardly any negative consequences for the wind turbine. The benefits for the grid are convincing, both in terms of increased system utilisation and in terms of provided inertia. It is concluded that wind turbines can enhance angular stability in a power system to a larger extent than conventional power plants.

Recent research has revealed surprisingly important connections between animals’ microbiome and social behaviour. Social interactions can affect the composition and function of the microbiome; conversely, the microbiome affects social communication by influencing the hosts’ central nervous system and peripheral chemical communication. These discoveries set the stage for novel research venues focusing on the evolution and physiology of animal social behaviour in relation to microbial transmission strategies. Here, we discuss the emerging roles of teleost fish model candidates and their key potential for advancing research fields linked to sociality and microbial regulation. We argue that fish models, such as the zebrafish, sticklebacks, guppies and cleaner-client dyads, will provide valuable insights into the roles of microbiome in shaping social behaviour and vice versa, while also being of direct relevance to the food and ornamental fish trades.

A checklist of parasitic cymothoids from Malaysian waters is presented based on available literature and material collected from 2010 to 2020. Most of the collected specimens were recorded from waters of Terengganu, east coast of Peninsular Malaysia (facing South China Sea), whereas literature records were represented from Sarawak, along the Miri coast of northwest Borneo. The checklist comprises 18 species under 10 genera, seven of which are new records from Malaysia, which includes Anilocra nemipteri Bruce, 1987; Ceratothoa barracuda Martin, Bruce and Nowak, 2015; Ceratothoa carinata (Bianconi, 1869); Cymothoa epimerica Avdeev, 1979; Elthusa sigani Bruce, 1990; Joryma engraulidis (Barnard, 1936) and Renocila richardsonae Williams and Bunkley-Williams, 1992. Eight new host records are based on collected specimens: Anilocra nemipteri was dorsally attached on Nemipterus nemurus (Bleeker 1857), Nemipterus nematophorus (Bleeker 1854), Nemipterus tambuloides (Bleeker 1853), and Nemipterus thosaporni Russell 1991 (family Nemipteridae); Ceratothoa carinata was found in the buccal cavity of Decapterus macrosoma Bleeker 1851 (family Carangidae); Cymothoa eremita (Brunnich, 1783) was attached in the buccal cavity of Nemipterus tambuloides and Nemipterus furcosus (Valenciennes 1830); Elthusa sigani was found attached on Pterois russelli Bennett 1831 (family Scorpaenidae); and Renocila richardsonae was attached on the caudal fin of Upeneus japonicus (Houttuyn 1782) (family Mullidae). All cymothoid species listed here are known to have a Central Indo Pacific distribution, with some ranging as far as the western Indian Ocean. The cymothoid-host association is here listed from 28 fish families, with the most common reported from Carangidae (pompanos, jack mackerels, runners, scads), Engraulidae (anchovies) and Leiognathidae (ponyfishes, slipmouths). This paper is the first comprehensive treatment to update both verified literature data and deposited specimens, with a key for the family Cymothoidae in Malaysian waters.

The main objective of this paper is to continue the development of activities of basic and applied research related to wind energy and to develop methods of optimal control to improve the performance and production of electrical energy from wind. A new control technique of Double fed induction generator for wind turbine is undertaken through a robust approach tagged nonlinear sliding mode control (SMC) with exponential reaching law control (ERL). The SMC with ERL proves to be capable of reducing the system chattering phenomenon as well as accelerating the approaching process. A nonlinear case numerical simulation test is employed to verify the superior performance of the ERL method over traditional power rate reaching strategy. Results obtained in Matlab/Simulink environment show that the SMC with ERL is more robust, prove excellent performance for the control unit by improving power quality and stability of wind turbine.

Fish currently provide 6.7% of all protein consumed by humans globally, nevertheless, aquaculture system has been linked to fish and environmental contamination and disease outbreak. This study aims to isolate, identify, and characterise, bacteria in fish and pond water as well as the antibiotic profile of detected Coliforms. The susceptibility of the isolates was tested using the Kirby-Bauer disc diffusion method on Mueller Hinton agar. A total of forty (40) isolates were isolated from the water samples of which (5) species were Gram Positive bacteria and 35 species of Gram Negative bacteria. The temperature for all ponds ranged from 25°C to 28°C. The mean bacteria count for pond C1 to T2 were 4.9 × 102, 4.9 × 102, 5.4 × 102, 2.5 × 102, 2.2 × 102, and 1.9 × 102 CFU/ml respectively. All isolates were 100% resistant to ceftazidime, cefuroxime and augmentin. More resistance to cefixime (80%) and gentamicin (73.3%) and nitrofurantoin (66.7%) was recorded. However, only 16.6% and 8.3% of the isolates were resistant to ciprofloxacin and ofloxacin respectively. The multiple antimicrobial resistance index (MARI) ranged from 0.5 to 0.9. The water quality parameters (temperature and pH) and the type of bacteria detected in all pond type did not differ significantly. The Multi-drug resistance bacteria detected could be pathogenic to fish and consumers.

Energy harvesting from wind turbines has been explored by researchers for more than a century from conventional turbines up to the latest bladeless turbines. Amongst these bladeless turbines, vortex bladeless wind turbine (VBT) harvests energy from oscillation of a turbine body. Due to the novelty of this science and the widespread researches around the world, one of the most important issues is to optimize and predict produced power. To enhance the produced output electrical power of VBT, the fluid-solid interactions (FSI) were analyzed to collect a dataset for predicting procedure. Long short-term memory (LSTM) method has been used to predict the produced power of VBT from the collected data. The reason of choosing LSTM from various artificial neural network methods is that the parameters of VBT study are all time- dependent and the LSTM is one of the most accruable algorithms for predicting time series data. In order to find the relationship between the parameter and the variables used in this research, a correlation matrix was presented. According to the value of 0.3 for the root mean square error (RMSE), a comparative analysis between the simulation results and its prediction shows that the LSTM method is very accurate for these types of research. Furthermore, the LSTM method has significantly reduced the computation time so that the prediction time of desired values has been reduced from an average of 2 and a half hours to two minutes. Also, one of the most important achievements of this study is to suggest a mathematical relation of VBT output power which helps to extend it in a different size of VBT with a high range of parameter variations.

This paper presents the super-twisting algorithm (STA) direct power control (DPC) scheme for the control of active and reactive powers of grid-connected DFIG. Simulations of 5 KW DFIG has been presented to validate the effectiveness and robustness of the proposed approach in the presence of uncertainties with respect to vector control (VC). The proposed controller schemes with fixed gains are effective in reducing the ripple of active and reactive powers, effectively suppress sliding-mode chattering and the effe This paper presents a comparative study of two approaches for the direct power control (DPC) of doubly-fed induction generator (DFIG) based on wind energy conversion system (WECS). Vector Control (VC) and Sliding Mode Control (SMC). The simulation results of the DFIG of 5 KW in the presence of various uncertainties were carried out to evaluate the capability and robustness of the proposed control scheme. The (SMC) strategy is the most appropriate scheme with the best combination such as reducing high powers ripple, diminishing steady-state error in addition to the fact that the impact of machine parameter variations does not change the system performance. cts of parametric uncertainties not affecting system performance.

The use of wind energy has been developing fast over the last years. The global cumulative wind power capacity increased by 10.5% in 2019, most of which comes from onshore wind farms. One of the consequences of this continuous increase is the use of land for onshore wind farms. There are already cases worldwide where lack of well-established plans and strategies have caused delays in projects. The need for efficiently using land for wind farms will be mandatory in the short term. In this work, we present a numerical analysis to evaluate wind farm land-use. By defining the ratio between mechanical output power over an area as a parameter called land-use ratio, this work focused on comparing several cases of aligned and staggered layouts. Mechanical output power was estimated using a validated code based on Blade Element Momentum code, and the wake velocities and wake interaction effects were estimated using a validated wind turbine CFD model. In terms of output power, staggered designs are more efficient than aligned designs. However, the results showed that even though staggered designs produced higher output power, aligned farms with tight lateral spacing could be as efficient as staggered ones in terms of land-use but using fewer turbines. In summary, tightly aligned designs should be a tendency in the future towards efficient use of land in wind farms.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

Defensive behavior is a function of specific survival circuits, the “aversive brain system”, that are thought to be conserved across vertebrates, and involve threat detection and the organization of defensive responses to reduce or eliminate threat. In mammals, these circuits involve amygdalar and hypothalamic subnuclei and midbrain circuits. The increased interest in teleost fishes as model organisms in neuroscience created a demand to understand which brain circuits are involved in defensive behavior. Telencephalic and habenular circuits represent a “forebrain circuit” for threat processing and organization of responses, being important to mounting appropriate coping responses. Specific hypothalamic circuits organize neuroendocrine and neurovegetative outputs, but are the less well-studied in fish. A “midbrain circuit” is represented by projections to interneurons in the optic tectum which mediate fast escape responses via projections to the central gray and/or the brainstem escape network. Threatening stimuli (especially visual stimuli) can bypass the “high road” and directly activate this system, initiating escape responses. Increased attention to these circuits in an evolutionary framework is still needed.

Chemical communication of predation risk has evolved multiple times in fish species, with the conspecific alarm substance (CAS) contemporaneously being the most well understood mechanism. CAS is released after epithelial damage, usually when prey fish is captured by a predator, and elicits neurobehavioral adjustments in conspecifics which increase the probability of avoiding predation. As such, CAS is a partial predator stimulus, eliciting risk assessment-like and avoidance behaviors, and disrupting the predator sequence. The present paper reviews the distribution and putative composition of CAS in fish, and presents a model for the neural processing of these structures by the olfactory and the brain aversive systems. Applications of CAS in the behavioral neurosciences and neuropharmacology are also presented, exploiting the potential of model fish (e.g., zebrafish, guppies, minnows) on neurobehavioral research.

The crack in the blade is the most common type of fatigue damage for Francis turbines. However, the crack sometimes is difficult to be detected in time using the current monitoring system even when the crack is very large. To better monitor the crack, it is imperative to research the effect of a crack on the dynamic behavior of a Francis turbine. In this paper, the dynamic behavior of a Francis turbine runner model with a crack was researched numerically. The intact numerical model was first validated by the experimental data available. Then, a crack was created at the intersection line between one blade and the crown. The change in dynamic behavior with increasing crack length was investigated. Crack-induced vibration localization theory was used to explain the dynamic behavior changes due to the crack. Modal analysis showed that the adopted theory could basically explain the modal behavior change due to the crack. The FFT results of the modal shapes and the localization factors (LF) were used to explain the forced response changes due to the crack. Based on the above analysis, the challenge of crack monitoring was analyzed. This research can also provide some references for more advanced monitoring technologies.

Coronaviruses are pathogens recognized for having an animal origin, commonly associated with terrestrial environments. However, although in a few cases, there are reports of their presence in aquatic organisms like fish, frogs, waterfowls and marine mammals. None of these cases has led to human health effects when contact with these infected organisms has taken place, whether they are alive or dead. Aquatic birds seem to be the main group carrying and circulating these types of viruses among healthy bird populations. Although the route of infection for CoVID-19 by water or aquatic organisms has not yet been observed in the wild, the relevance of its study is highlighted because there are cases of other viral infections known to have been transferred to humans by aquatic biota. It is encouraging to know that aquatic species, such as fish, marine mammals, and amphibians, shows very few cases of coronaviruses and that some other aquatic animals may also be a possible source of cure or treatment against then, as some evidence with algae and marine sponges suggest.

Atmospheric stability affects wind turbine wakes significantly. High-fidelity approaches such as large eddy simulations (LES) with the actuator line (AL) model which predicts detailed wake structures, fail to be applied in wind farm engineering applications due to its expensive cost. In order to make wind farm simulations computationally affordable, this paper proposes a new actuator disk model (AD) based on the blade element method (BEM) and combined with Reynolds-averaged Navier–Stokes equations (RANS) to model turbine wakes under different atmospheric stability conditions. In the proposed model, the upstream reference velocity is firstly estimated from the disk averaged velocity based on the one-dimensional momentum theory, and then is used to evaluate the rotor speed to calculate blade element forces. Flow similarity functions based on field measurement are applied to limit wind shear under strongly stable conditions, and turbulence source terms are added to take the buoyant-driven effects into consideration. Results from the new AD model are compared with field measurements and results from the AD model based on the thrust coefficient, the BEM-AD model with classical similarity functions and a high-fidelity LES approach. The results show that the proposed method is better in simulating wakes under various atmospheric stability conditions than the other AD models and has a similar performance to the high-fidelity LES approach however in much lower computational cost.

High-content fluorescence microscopy combines the efficiency of high-throughput techniques with the ability to extract quantitative information from biological systems. The planarian community has developed sensitive and robust assays for whole animals, yet cell based assays, despite their practical aspects, have not been explored to the same extent. Here we describe a modular collection of detailed protocols adapted for fixed planarian cells that enable multiplexed measurements of biomarkers in microwell plates. Methods include the detection of RNA transcripts by RNA fluorescent in situ hybridization combined with tyramide signal amplification using hapten-labeled riboprobes. In addition, immunocytochemical protocols for quantifying proliferating cells by the detection of phosphorylated histone H3 as well as 5-bromo-2'-deoxyuridine incorporation into the nuclear genome are described. The assays are compatible with planarians of virtually any size, as the tissue is disaggregated into a single cell suspension before fixation and staining. By sharing many reagents with established planarian whole mount staining protocols, preparation of samples for high-content microscopy adoption requires little additional investment. Recommendations for successful experimental workflows and common sources of errors are discussed.

Mixture of abramis brama (freshwater bream), carassius carassius (crucian carp), and sander lucioperca (pike perch) scales was used for the preparation of fish scale powder containing about 26.5 wt. % of removed when heating components preferably of organic nature, and 63.5 wt. % of mineral components. Fish scale powder enriched with inorganic components was prepared from washed, dried, and ground fish scale mixture using vibration sieving. Inorganic powders consisting of hydroxyapatite and magnesium whitlockite were obtained via heat treatment of this fish scale powder at 800-1000 oC. Particles of these inorganic powders consisted of sintered grains with dimensions less than 100 nm after heat treatment at 800 oC, less than 200 nm after heat treatment at 900 oC, and 100-500 nm after heat treatment at 1000 oC. Fish scale powder enriched with inorganic components as well as heat-treated inorganic powders consisting of hydroxyapatite and magnesium whitlockite can be recommended for the production of different materials such as ceramics or composites.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil &amp; gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

In recent years, demand for consumption of marine foods, and especially fish, has substantially increased worldwide. The majority of collagen available is sourced from mammalian-derived products. Although fish derived gelatine is a viable alternative to mammalian sourced gelatine, there are some challenges related to the use of fish gelatine including odour, colour, gelling and film forming properties as well as consistency in gelatine amino acid composition. Chemicals used for pre-treatment, as well as extraction conditions such as temperature and time, can influence the length of polypeptide chains that result and the functional properties of the gelatine. Compared to mammalian sources, gelatines derived from fish show notable differences in physical and chemical properties, and great care should be paid to optimization of the production process in order to obtain a product with the best properties for intended applications. The focus of this review is to explore the feasibility of producing gelatine sourced from marine processing by-products using different pre-treatment and extraction strategies with the aim of improving the techno-functional properties of the final product and improving the clean-label status of gelatines. The bioactivities of gelatine hydrolysates are also discussed.

It is often difficult to extract data on material and energy wates and related costs in the value chain of conventional production units. Many organizations are not fully aware of the actual cost of material and energy waste. For this purpose, advanced costing methods should be used. This study uses material and energy flow cost accounting to determine material costs, losses, and waste management. The case study of this research is the construction of turbine blades in Iran Power Plant Company. In this study, using the extracted data, the construction costs of turbine blades have been studied. The conventional method of making a turbine blade is the machining method, which we will see has a huge amount of wastes of materials and energy. By studying different methods, we will find that there is an alternative method called forging, which reduces losses and costs. Finally, the costs of the two methods are compared. Engineering economics techniques have also been used to compare two methods on a long-term planning horizon.

In this study, a composite flame retardant was created by combining fish scale (FS), fishery waste, and ammonium polyphosphate (APP), a commercially available flame retardant. The composite flame retardant was added to epoxy resin (EP) to form an EP/APP/FS composite that prevents burns and is environmentally friendly. The use of FS conforms to the concept of circular economy and lowers costs by reducing the consumption of APP. Thermogravimetric analysis (TGA), integral procedural decomposition temperature (IPDT), pyrolysis kinetics, limiting oxygen index (LOI), the Underwriters Laboratories 94 (UL94) flammability test, scanning election microscopy, Raman spectroscopy, and energy-dispersive X-ray spectroscopy were used to determine the thermal properties, flame retardant properties, flame retardant mechanism, char morphology, and composition of the composites. The TGA results indicated that the addition of 40% flame retardant raised the char residue from 16.45 wt% (pure EP) to 36.07 wt%, IPDT from 685.6 °C (pure EP) to 1143.1°C, LOI from 21% (pure EP) to 30%, and UL94 classification from fail (pure EP) to V-0. These results suggest an increase in char residue, which indicates better protection of the polymer matrix material. The improvements in IPDT, LOI, and UL94 classification, which indicate greater thermal stability, lower flammability (from flammable to fireproof), and higher flammability rating (from fail to V-0), respectively, suggest that the composite material has favorable thermal properties and is less inflammable.

Hydrogen plays a key role in the transition to a carbon-free economy. One of the areas of hydrogen use is the substitution of hydrocarbon fuel in gas turbine engines and power plants. This review article discusses the features of hydrogen combustion and their influence on the characteristics of combustion chambers in comparison with methane. The paper presents both the results of a study of pure hydrogen or methane and methane-hydrogen mixtures with different hydrogen content. Among the main features, it is worth noting a smaller ignition delay time and higher laminar flame speed with a shift in its maximum value to a rich mixture, which significantly affects on flashback inside burners premixer, especially at elevated air temperatures. Another feature is the increased temperature of the flame, which can lead to an increase in the rate of nitrogen oxides formation. However, wider combustion concentration ranges contribute to the stable combustion of hydrogen at temperatures lower than those of methane. Along with this, it was shown that even at the same adiabatic temperature, more nitrogen oxides are formed in a hydrogen flame than in a methane flame, which indicates an additional mechanism for NOx formation in addition to the Zeldovich mechanism. The article also summarizes some of the results of a study on the effect of hydrogen on the occurrence of thermoacoustic instability, which depends on the initial nature of pulsations during methane combustion. The presented data will be useful both to engineers who are engaged in solving the problems of designing hydrogen combustion devices, and to scientists in this field of study.

Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

The interest on the use of renewable energy resources is increasing, especially towards wind and hydro powers, which should be efficiently converted into electric energy via suitable technology tools. To this aim, self--tuning control techniques represent viable strategies that can be employed for this purpose, due to the features of these nonlinear dynamic processes working over a wide range of operating conditions, driven by stochastic inputs, excitations and disturbances. Some of the considered methods were already verified on wind turbine systems, and important advantages may thus derive from the appropriate implementation of the same control schemes for hydroelectric plants. This represents the key point of the work, which provides some guidelines on the design and the application of these control strategies to these energy conversion systems. In fact, it seems that investigations related with both wind and hydraulic energies present a reduced number of common aspects, thus leading to little exchange and share of possible common points. This consideration is particularly valid with reference to the more established wind area when compared to hydroelectric systems. In this way, this work recalls the models of wind turbine and hydroelectric system, and investigates the application of different control solutions. The scope is to analyse common points in the control objectives and the achievable results from the application of different solutions. Another important point of this investigation regards the analysis of the exploited benchmark models, their control objectives, and the development of the control solutions. The working conditions of these energy conversion systems will be also taken into account in order to highlight the reliability and robustness characteristics of the developed control strategies, especially interesting for remote and relatively inaccessible location of many installations.

Although researchers have investigated widely the impact of IOD phases on human lives, only a few have examined such impacts on fisheries. In this study, we analyzed the influence of negative (positive) of IOD on a chlorophyll a (Chl-a) concentration as an indicator of phytoplankton biomass and small pelagic fish production in the eastern Indian Ocean (EIO) off Java. We also conducted field surveys in the EIO off Palabuhanratu Bay at the peak (October) and the end (December) of the 2019 positive IOD phase. Our findings show that the Chl-a concentration had a strong and robust association with the 2016 (2019) negative (positive) IOD phases. The negative (positive) anomalous Chl-a concentration in the EIO off Java associated with the negative (positive) IOD phase induced strong downwelling (upwelling), leading to the preponderant decrease (increasing) of small pelagic fish production in the EIO off Java.

Soups show diverse health functions, which should be related with their nutrient profiles. NMR spectroscopy is a robust, sensitive and rapid method to unveil or identify the chemical composition of food or food-derived metabolites. In the current study, 1H-NMR spectroscopy approach was applied to identify the metabolic profiling of two kinds of home-cooked freshwater fish soups (crucian carp and snakehead fish) before and after in vitro gastrointestinal digestion. The nutritional profiles of these two kinds of soups were identified at first. With the help of OPLS-DA method (Orthogonal Partial Least Squares Discriminant Analysis), these two different kinds freshwater fish under different states were completely discriminated. The metabolites changes in digested fish soups could reveal the information of chemical compounds which play important roles in the body. Furthermore, the metabolic patterns of different kinds of fish soups could reflect the various nutrition profiling characteristics for dietary therapy.

Otolith morphology analysis is one of the main tools used for fish or fish stock identification. Moreover, otolith shape can also be used in fish dietary studies (stomach content) for the identification of prey fishes and their size according to the relationship between fish and otolith sizes. In the present study, the relationship between fish length and otolith morphological dimensions was investigated for the sabre squirrelfish, Sargocentron spiniferum (Forsskål, 1775) (family: Holocentridae). Samples of 185 fish were collected from the coast of the Red Sea, Egypt. To analyze the relationship between fish and otolith, otolith morphometric measurements (length, width, area, perimeter, weight, sulcus, and ostium) and shape factors (aspect ratio, compactness, form factor, rectangularity, roundness, ellipticity, squareness) describing outline shape were extracted using image analysis. Generalized linear models were applied for the relationship between body length and each otolith morphology feature. From the relationships between the total length of fish and fourteen morphology features, only otolith length, caudal length, and squareness were significantly correlated with fish size. Our results provide more information for the relationship between fish length and otolith morphometric features.

In recent years, demand for consumption of marine foods, and especially fish, has substantially increased worldwide. The majority of collagen available is sourced from mammalian-derived products. Although fish derived gelatine is a viable alternative to mammalian sourced gelatine, there are some challenges related to the use of fish gelatine including odour, colour, gelling and film forming properties as well as consistency in gelatine amino acid composition. Chemicals used for pre-treatment, as well as extraction conditions such as temperature and time, can influence the length of polypeptide chains that result and the functional properties of the gelatine. Compared to mammalian sources, gelatines derived from fish show notable differences in physical and chemical properties, and great care should be paid to optimization of the production process in order to obtain a product with the best properties for intended applications. The focus of this review is to explore the feasibility of producing gelatine sourced from marine processing by-products using different pre-treatment and extraction strategies with the aim of improving the techno-functional properties of the final product and improving the clean-label status of gelatines. The bioactivities of gelatine hydrolysates are also discussed.

Seafood is considered one of the main food allergen sources by the European Food Safety Authority (EFSA). It comprises several distinct groups of edible aquatic animals including fish and shellfish such as crustacean and mollusks. Recently the EFSA recognized the high risk of food allergy over the world and established the necessity of developing new methodologies for its control. Consequently, accurate, sensitive and fast detection methods for seafood allergy control and detection in food products are highly recommendable. In this work, we present a comprehensive review of the applications of the proteomics methodologies for the detection and quantification of seafood allergens. For that, two consecutive proteomics strategies (Discovery and Targeted Proteomics) applied for the study and control of seafood allergy are reviewed in detail. In addition, future directions and new perspectives were also provided.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

Mouthbrooding or oral incubation, the retention of early developmental stages inside of the mouth for an extended period of time, has evolved multiple times in bony fishes1,2. Though uncommon, this form of parental care has been documented and well-studied in several groups of freshwater fishes but is also known to occur in a small number of marine fishes, all inhabiting coastal waters1,2. A recent paper3, reported for the first time mouthbrooding in a deep-water fish species, the zeiform Parazen pacificus, which according to the authors “fills in a gap in the larval literature for this family of fishes and prompts further investigation into other novel reproductive modes of deep-sea fauna.”

The urban population in developing countries, especially sub-Saharan Africa, is rapidly increas-ing. As towns and cities grow, so does the demand for fish protein. While flow-through aqua-culture can provide fresh, healthy and nutritious fish protein, it is plagued by extensive land re-quirement as well as effluent discharge, thus, unsuitable for city regions. Alternatively, small-scale Recirculating Aquaculture System (RAS) could improve food and nutritional security (FNS), livelihoods as well as reduce environmental degradation in urban areas despite land and water constraints. The question however remains - what are the key technical, business and managerial issues, surrounding small-scale RAS in urban farming? This study reviews the RAS prototype of the Sustainable Aquaponics for Nutritional and Food Security in Urban Sub-Saharan Africa (SANFU) II project based on mass balance and stock density, relevant for fish survival and/or availability as well as net cash-flow analyses. The results suggest that small-scale RAS are technically and financially viable only with family labor having proper aquaculture monitoring and management skills. Furthermore, access to adequate equipment and inputs as well as electricity for the recirculating system are crucial. Urban innovation actors will adopt RAS if operations are profitable given that family labor is employed.

Different kinds of freshwater fish soups show a diverse range of health functions, due to their different nutritional substances and corresponding bioactivities. Crucian carp soup and snakehead soup have different dietotherapy functions, crucian carp soup is suitable for lactating women and snakehead soup is suitable for postoperative patients. In the current study, the changes of nutrient profiles in the different fish soups, such as chemical composition, free amino acids, mineral and fatty acid contents, were investigated. The antioxidant activities of the fish soups were evaluated by using the DPPH radical scavenging activity, the ferrous ion chelating activity, the hydroxyl radical-scavenging activity and the reducing power effect. In order to learn the theoretical basis of the potential role fish soup plays in diet therapy functions after being digested by the human body, the nutrient profiling and bioactivities of the fish soup samples after simulated gastrointestinal digestion were also explored. The intensive profiles of nutritional composition and antioxidant activities of these two kinds of fish soups were expected to partly provide the theoretical basis of therapeutic effects.

Glyphosate (N-(phosphonomethyl)glycine) is a herbicide used to kill broadleaf weeds and grass, developed in the early 1970s. The widely occurring degradation product aminomethylphosphonic acid (AMPA) is a result of glyphosate and amino-polyphosphonate degradation. The massive use of the parent compounds leads to the ubiquity of AMPA in the environment, and particularly in water. Considering this, it can be assumed that glyphosate and its major metabolites could pose a potential risk to aquatic organisms. This review summarises current knowledge about residual glyphosate and their major metabolite AMPA in the aquatic environment, including status and toxic effects in aquatic organisms, mainly fish, are reviewed. Based on the above, we identify major gaps in the current knowledge and some directions for future research knowledge about the effects of worldwide use of herbicide glyphosate and its major metabolite AMPA. The toxic effect of glyphosate and their major metabolite AMPA has mainly influenced growth, early development, oxidative stress biomarkers, antioxidant enzymes, haematological, biochemical plasma indices, caused histopathological changes in the aquatic organism.

The present study explores the effect of using two porous deflectors on the performance of the Savonius wind turbine compared to only one porous deflector. The numerical simulation is performed to solve the unsteady Navier-Stokes equations using the SST k-

Some wind farms have implemented automated camera\textendash based monitoring systems e.g. IdentiFlight to mitigate the impact of wind turbines on protected raptors. These systems have effectuated the collection of large amounts of data that can be used to describe flight behavior in a novel way. This data uniquely provides both flight trajectories and images of individual birds throughout their flight trajectories. The aim of this study was to evaluate how this unique data could be used to create a robust quantitative behavioral analysis, that could be used to identify risk prone flight behavior and avoidance behavior thereby in the future assess collision risk. This was attained through a case study at a wind farm on the Swedish island Gotland, where golden eagles (Aquila chrysaetos), white-tailed eagles (Haliaeetus albicilla), and red kites (Milvus milvus), were chosen as the selected bird species. The results demonstrate that flight trajectories and bird images can be used to identify high risk flight behavior and thereby also used to evaluate collision risk and avoidance behavior. This study presents a promising framework for future research, demonstrating how data from camera\textendash based monitoring systems can be utilized to quantitatively describe risk prone behavior and thereby assess collision risk and avoidance behavior.

Traditional edible barbecue products use with lemon juice not only make the barbecue more delicious but also reduce the risk of PAHs in the barbecue products. One of the major economics crops in Taiwan, the waste from citrus fruits was very tremendous mass. However, the peelings of citrus fruits are rich in essential oil, especially, the limonene is the major. Whether the anti-carcinogenesis activities of terpene, such as limonene, in citrus fruits essential oil extraction. This study to demonstrate the PAHs content in fish skin increased markedly after being roasted at 210℃ for 20 minutes and greater mutagenicity risk of roasted fish skin was observed by Ame's test. The reduction of mutagenicity risk of roasted fish skin, which the antimutagenic abilities of substances in descending order were limonene > cold pressure oil > lemon >grapefruit. The antimutagenicity rate and ability of the three extracts were limonene: 18–23%; cold-pressed lemon oil: 18–22%; and steam distilled lemon essential oil: 8–16%. The obvious anti- mutagenicity effects against the PAHs mutagenicity of roasted fish skins can be found in citrus fruits essential oil extraction.

Age-related macular degeneration (AMD) is a complex multifactorial disease and the primary cause of legal and irreversible blindness among individuals aged >=65 years in developed countries. Globally, it affects 30-50 million individuals, with an estimated increase of approximately 200 million by 2020 and approximately 300 million by 2040. Currently, the neovascular form may be able to be treated with the use of anti-VEGF drugs, while no effective treatments are available for the dry form. Many observational studies, such as AREDS-1 and AREDS 2, have shown a potential role of micronutrient supplementation in lowering the risk of progression of the early stages of AMD. Recently, low-grade inflammation, sustained by dysbiosis and a leaky gut, has been shown to contribute to the development of AMD. Given the ascertained influence of the gut microbiota in systemic low-grade inflammation and its potential modulation by macro- and micro-nutrients, a potential role of diet in AMD has been proposed. This review discusses the role of the gut microbiota in the development of AMD. Using PubMed, Web of Science and Scopus, we searched for recent scientific evidence discussing the impact of dietary habits (high fat and high glucose or fructose diets), micronutrients (vitamins C, E, and D, zinc, beta-carotene, lutein and zeaxanthin) and omega-3 fatty acids on the modulation of the gut microbiota and their relationship with AMD risk and progression.

Current prenatal genetic evaluation showed a significantly increase in non-invasive screening and the reduction of invasive diagnostic procedures. To evaluate the diagnostic efficacy on detecting common aneuploidies, structural chromosomal rearrangements and pathogenic copy number variants (pCNV), we performed a retrospective analysis on a case series initially analyzed by aneuvysion fluorescence in situ hybridization (FISH) and karyotyping then followed by array comparative genomic hybridization (aCGH). Of the 386 cases retrieved from the past decade, common aneuploidies were detected in 137 cases (35.5%), other chromosomal structural rearrangements were detected in four cases (1%), and pCNV were detected in five cases (1.3%). The relative frequencies for common aneuploidies suggested a under detection of sex chromosome aneuploidies. Approximately 9.5% of cases with common aneuploidies showed a mosaic pattern. Inconsistent results between FISH and karyotyping were noted in cases with pseudo-mosaicism introduced by culture artifact or variable cellular proliferation from cells with mosaic karyotypic complements under in vitro cell culture. Based on findings from this case series, cell-based FISH and karyotyping should be performed to detect common aneuploidies, structural chromosomal abnormalities, and mosaic pattern. DNA-based aCGH and reflex FISH should be performed to detect and confirm genomic imbalances and pCNV. Practice points to ensure the diagnostic accuracy and efficacy were summarized.

Fullerene molecules are composed of carbon in forms of a hollow sphere, ellipsoid, or tube. Fullerenes have attracted considerable attention in different fields of science since their discovery in 1985. The unique carbon cage structure of fullerene provides immense scope for derivatization, rendering potential for various industrial applications. The prospective applications of fullerenes thus have led to assorted fullerene derivatives. The unique chemical structure also provides ease for fullerene to be synthesized through various kinds of conjugating techniques, where fullerene can be located either on the backbone or the branch chain. Here in this review, we have compiled the toxicity and biosafety aspects of fullerene in aquatic organisms. The frequent use of fullerene is likely to come in contact and interact with the aquatic environment and aquatic organisms. According to the current understanding, waterborne exposure to fullerene-based nanomaterials indeed triggers toxicities at cellular, organic, molecular as well as neurobehavioral levels.

Argulus is an ectoparasite that frequently infects goldfish, with severe effects and a high death rate. The use of plant extracts has been widely reported to have antiparasitic activities, including one of the solasodine compounds in sour eggplant extracts. This research evaluated the antiparasitic activities of Compositions A (Solanum ferox and Zingiber zerumbet extract at 400 and 200 ppm, respectively), B (SFE and Boesenbergia pandurata at 900 ppm), and C (single Solanum ferox at 400 ppm). The research stages comprised 1) isolation and analysis of solasodine content in sour eggplant extracts and its extract composition, 2) in vitro antiparasitic activities on Argulus sp. at doses of 50 and 100 ppm with a testing time of 60–240 minutes, and 3) in vivo antiparasitic activities on Argulus sp. on goldfish at a dose of 100 ppm and observation for 2–12 hours of medication. The results showed that sour eggplant extracts had a solasodine concentration of 7.151 mg/L, whereas the derivative compositions A, B, and C were 656, 485, and 295 ppm, respectively. The in vitro testing demonstrated that composition A was effective for killing approximately 80–100% of Argulus, whereas compositions B and C killed 80–90% and 60–70%, respectively. Viewed from the effectiveness for killing parasites, the result was excellent (above 50%). The in vivo medication test was continued using three extract compositions at a dose of 100 ppm. Compositions A, B, and C were found to be capable of releasing 81.33, 75.67, and 71.00 arguli, respectively, per fish. We concluded that the single SFE extract and a concoction with BPE and ZZE had reasonable antiparasitic activity, whereas the concoction of SFE and ZZE killed more Argulus parasites at a higher rate.

The health status and feed conversion efficiency of farmed fish may vary according to management and production methods. Successful aquaculture requires safeguarding the health of the growing fish and optimizing the feed conversion and therefore achieving better FCE thus reducing the amount of feed required to produce farmed fish, reducing the environmental impact generated by fish feed production and reducing aquaculture wastes generated by feed wasted or poorly digested. The present review presents illustrative examples from freshwater aquaculture that suggests the potential dual benefits of focusing on the link between feed conversion and the environmental impact of fresh water fish farms. Apart from the need to support future research on new diets for farmed fish (which is mainly driven by limits in the supply of fish protein and the results price fluctuation of all ingredients used by the aquaculture, feed industry), major improvements can be expected by optimizing feeding regimes and the application of probiotics. Aside from the economic benefits and increased production of fish farms, improved feeding regimes and probiotics are expected to have a significant impact on the welfare of farmed fish as well as on digestion efficiency and the environmental impact of fresh water fish farms.

The Virtual Blade Model (VBM) is the implementation of the Blade element model (BEM). This was done by coupling the Blade Element Momentum theory equations to simulate rotor operation with the Reynolds Averaged Navier-Stokes (RANS) equation to simulate rotor wake and the turbulent flow field around it. Exclusion of actual geometry of blades causes lower computational cost (about 10 to 100 times). Also, due to simplifications in the meshing procedure, VBM is easier to set up than the models that consider the actual geometry of blades. One of the main unaddressed limitations of the VBM code was the constraint of modeling up to ten rotor zones within one computational domain. This paper provides a detailed and well-documented general methodology to develop a virtual blade model for simulation of ten-plus turbines within one computational domain to remove the limitation of this widely used and robust code. It is strongly believed that the technical contribution of this paper, combined with the current sky-rocketing advancement of available computational resources and hardware, would open the gates to simulate various engineering problems in the field of aerospace, clean energy, and many more.

The basic pattern of MHC variation in fish, with MHC class I versus class II, and polymorphic classical versus nonpolymorphic nonclassical, is similar in fish and mammals. Nevertheless, in many or all teleost fishes, important differences with mammalian or human MHC were observed: (1) The allelic/haplotype diversification levels of classical MHC class I genes tend to be much higher than in mammals; (2) Teleost fish classical MHC class I and class II loci are not linked. The present article summarizes previous studies that performed quantitative trait loci (QTL) analysis for mapping differences in teleost fish disease resistance, and discusses them from MHC point of view. Overall, those studies suggest the possible importance of genomic regions including classical MHC class II and nonclassical MHC class I genes, whereas similar observations were not made for the genomic regions with the highly diversified classical MHC class I alleles. The present study is a review and discussion of the fish MHC situation.

Vibrio is a bacterial genus widely distributed in natural aquatic systems. Some Vibrio species are pathogenic and can cause severe diseases in both marine organisms and humans. Previous studies revealed a link between the current climate change and increased incidence of the Vibrio-associated diseases recently causing sanitary, economic and/or ecological problems worldwide. The conventional culture-based methods (e.g. cultivation of TCBS agar) used to monitor the presence of Vibrio spp. in environmental samples are not always straightforward and can underestimate the number of cells, especially if the microbial population contains a fraction of ‘dormant’ cells (e.g. cells in Viable but not Culturable (VBNC) state). However, this problem can be overcome by using alternative culture-free approaches such as Catalyzed Reporter Deposition-Fluorescence In situ Hybridization (CARD-FISH). To optimize CARD-FISH for efficient and reliable detection of Vibrio spp. in environmental samples, we have used both computer-assisted and experimental approaches. Our results demonstrate that the use of the optimized protocol along with a very specific probe, ViB572a, can offer the high sensitivity and selectivity of CARD-FISH detection of marine vibrios in natural seawater.

The present study was carried out at the north-eastern part of Bangladesh to investigate organochlorine pesticide (OCP) residues and microbiological quality of dried barb (Puntius sophore). Samples were collected from both producers and retailers from December 2016 to April 2017. A control sample was also prepared with the same raw fish used by the producers in the laboratory to compare the result. Gas Chromatography with Electron Capture Detector (GC-ECD) was used to detect and quantify OCP residues. Around 22 % (6) samples out of 27 were found contaminated with OCP residues. Among these six adulterated samples, four were from retailers and two from producers. Only Aldrin was detected in four samples and rest two samples were detected with both Aldrin + Dieldrin and Aldrin + Endrin. Aldrin was found between 0.332 to 0.967 ppm, Dieldrin 0.762 ppm, and Endrin 0.828 ppm. All these values were much higher than the Maximum Residual Limit (MRL) 0.1 ppm. Aerobic Plate Count (APC) of producer samples were ranged between log5.3 ± 0.02 to log5.4 ± 0.03, log6.2 ± 0.02 to log6.4 ± 0.02 for retailer samples and log5.0 ± 0.03 to log5.2 ± 0.04 for control samples. While fungal count was ranged between log3.2 ± 0.04 to log3.5 ± 0.04, log3.4 ± 0.04 to log3.6 ± 0.03 and log2.2 ± 0.05 to log2.5 ± 0.03 for producer, retailer and control samples respectively. All the producer and retailer samples and one-third of the control samples were found contaminated with Escherichia coli. Whereas, Salmonella sp. was detected as 13.3% in producer samples, 20% in retailer samples except for the control. In case of Vibrio sp., maximum count was found for retailer samples (13.3%), whereas, producer and control samples showed no detection. The finding of the present study revealed the presence of pesticides and poor microbiological quality of dried barb are alarming for the consumers of Bangladesh and which may cause chronic disease and potential long-term risk for human health.

Coincident changes in abundance and behavior pose a challenge for interpreting abundance data from monitoring programs. In the San Francisco Estuary, long-term monitoring documented the declines of many species including the anadromous Longfin Smelt (Spirinchus thaleichthys). We identified seasonal patterns in reginal presence of Longfin Smelt through its life cycle using monitoring data and generalized additive modelling. We then investigated the year-to-year variability in the seasonal patterns of presence using functional data analysis (FDA). FDA separated the variability due to population size from variability due to differences in timing of presence. We found that Longfin Smelt have consistent seasonal distribution patterns and that two trawl types were needed to accurately describe those patterns. After accounting for variability due to year-class strength, shifts in the timing of presence were evident in three regions. The most variable period for the upstream regions Suisun Bay and West Delta was for age-0 fish in summer and for the downstream region Central Bay was for age-0 fish in late fall. This manifested as a delay in the typical fall re-occupation of upstream regions that comprise the study area for another monitoring study (Fall Midwater Trawl). Thus, a portion of the recent reductions in Fall Midwater Trawl abundance of Longfin Smelt resulted from changes in behavior rather than a decline in abundance. The presence of multiple monitoring surveys allowed analysis of distribution from one data set to aid interpretation of patterns in abundance from another monitoring survey. This study highlights how identifying portions of the life cycle with the most and least variability in distribution can help inform the types of management strategies that will be most effective. It also illustrates an analytical method that can be used to address the problem of confounded effects of abundance and behavior on patterns in monitoring data.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Otolith morphology analysis is one of the main tools used for fish or fish stock identification. Moreover, otolith shape can also be used in fish dietary studies (stomach content) for the identi-fication of prey fishes and their size according to the relationship between fish and otolith sizes. In the present study, the relationship between fish length and otolith morphological dimensions was investigated for the sabre squirrelfish, Sargocentron spiniferum (Forsskål, 1775) (family: Hol-ocentridae). Samples of 185 fish were collected from the coast of the Red Sea, Egypt. To analyze the relationship between fish and otolith, otolith morphometric measurements (length, width, area, perimeter, weight, sulcus, and ostium) and shape factors (aspect ratio, compactness, form factor, rectangularity, roundness, ellipticity, squareness) describing outline shape were extracted using image analysis. Generalized linear models were applied for the relationship between body length and each otolith morphology feature. From the relationships between the total length of fish and fourteen morphology features, only otolith length, caudal length, and squareness were significantly correlated with fish size. Our results provide more information for the relationship between fish length and otolith morphometric features.

Mercury (Hg) fish and seafood contamination is a global concern and needs worldwide sea investigations in order to protect consumers. The aim of this study was to investigate the Hg concentration by means of a rapid and simple analytical technique with direct Mercury Analyzer (DMA-80) in pelagic fish species, Tetrapturus belone (spearfish), Thunnus thynnus (tuna) and Xiphias gladius (swordfish) caught in the Mediterranean Sea. Hg contents were evaluated also in Salmo salar (salmon) as pelagic fish not belonging to the Mediterranean area. The results obtained were variable ranging between 0,015-2,562 mg kg-1 for T. thynnus specie, 0,477-3,182 mg kg-1 for X. gladius, 0,434-1,730 mg kg-1 for T. belone and 0,004-0,019 mg kg-1 for S. salar, respectively. The total Hg tolerable weekly intake (TWI) and % tolerable weekly intake (TWI%) values according to the European Food Safety Authority (EFSA) were calculated. The results highlighted that the pelagic species caught in the Mediterranean Sea should be constantly monitored due to their high Hg contents as well as their TWI and TWI% with respect to S. salar samples.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

Salmon farming has been blamed for the collapse of the sea trout (Salmo trutta) fishery in Loch Maree on Scotland’s west coast despite the absence of any direct evidence. Stocks of west coast demersal marine fish, especially around the Clyde Estuary have also declined over a similar time span. The decline of these marine fish stocks can be attributed to the removal of the “three-mile fishing limit” in 1984 by UK Government legislation. Sea trout inhabit the same inshore waters as targeted demersal fish and can be caught as by-catch. Comparisons of the decline of demersal species and the sea trout from Loch Maree and the west coast show a high degree of correlation. Stocks of whiting (Merlangius merlangus) from inshore waters have found to consist of small fish which mirrors the stock makeup of the Loch Maree sea trout stock.

Brucellosis is one of the most common etiologies of laboratory-acquired infections worldwide, and handling of living brucellae should be performed in a Class II biological safety cabinet. The low infecting dose, multiple portals of entry to the body, the great variety of potentially contaminated specimens, and the unspecific clinical manifestations of human infections facilitate the unintentional transmission of brucellae to laboratory personnel. Work accidents such as spillage of culture media cause only a small minority of exposures, whereas >80% of events result from unfamiliarity with the phenotypic features of the genus, misidentification of isolates, and unsafe laboratory practices such as aerosolization of bacteria and working on an open bench without protective goggles or gloves. Although the bacteriological diagnosis of brucellae by traditional methods is simple, the Gram stain and the biochemical profile of the organism, as determined by commercial kits, can be misleading, resulting in inadvertent exposure and contagion. The use of novel identification technologies is not hazard-free. The MALDI-TOF technology requires an initial bacterial inactivation step, while the instruments’ reference database may misidentify Brucella as belonging to other Gram-negative species. The rapid identification by the FISH method mistakes brucellar isolates for members of the closely related Ochrobactrum genus.

Organisms release their nucleic acid in the environment including the DNA and RNA which can be used to detect their presence. eDNA/eRNA techniques are being used in different sectors to identify organisms from soil, water, air, and ice since long. The advancement in technology led to easier detection of different organisms without impacting the environment and the organism itself. These methods are being employed in different areas including surveillance, history, and conservation. eDNA and eRNA methods are being extensively used in aquaculture and fisheries setting to understand the presence of different fish species and pathogens in water. However, there are some challenges associated with the reliability of the results because of the degradation of nucleic acid by several factors. In aquaculture there are several diseases and parasites detected with these methods. In this review we discuss different aquaculture diseases and parasites detected with eDNA/eRNA approach and the fate of these nucleic acids when subjected to different water quality and environmental parameters. This review intends to help the researcher about the potential of eDNA/eRNA based detection of pathogens in aquaculture; this will be useful to predict the potential outbreak before it occurs. Along with that this paper intends to make people understand several factors that degrade and can hamper the detection of these nucleic acids.

In this paper, the active front-end (AFE) converter topology for the total harmonic distortion (THD) reduction in a wind energy system (WES) is used. A higher THD results in serious pulsations in the wind turbine (WT) output power and in several power losses at the WES. The AFE converter topology improves capability, efficiency and reliability in the energy conversion devices; by modifying a conventional back-to-back converter, from using a single voltage source converter (VSC) to use pVSC connected in parallel the AFE converter is generated. The THD reduction is done by applying a different phase shift angle at the carrier of digital sinusoidal pulse width modulation (DSPWM) switching signals of each VSC. To verify the functionality of the proposed methodology, the WES simulation in Matlab-Simulink® is analyzed, and the experimental laboratory tests using the concept of rapid control prototyping and the real-time simulator Opal-RT® Technologies is achieved. The obtained results show a type-4 WT with total output power of 6MVA, generating a THD reduction up to 5.5 times at the WES.

Tidal stream energy, due to its high level of consistency and predictability, is one of the feasible and promising type of renewable energy for future development and investment. Applicability of Blade Element Momentum (BEM) method for modeling the interaction of turbines in tidal arrays has been proven in many studies. Apart from its well-known capabilities, yet there is scarcity of research using BEM for the modeling of tidal stream energy farms considering full scale rotors. In this paper, a real geographical site for developing a tidal farm in the southern coasts of Iran is selected. Then, a numerical methodology is validated and calibrated for the selected farm by analyzing array of turbines. A linear equation is proposed to calculate tidal power of marine hydrokinetic turbines. This methodology narrows down the wide range of turbine array configurations, reduces the cost of optimization and focuses on estimating best turbine arrangements in a limited number of positions.

The interest on the use of renewable energy resources is increasing, especially towards wind and hydro powers, which should be efficiently converted into electric energy via suitable technology tools. To this aim, data--driven control techniques represent viable strategies that can be employed for this purpose, due to the features of these nonlinear dynamic processes working over a wide range of operating conditions, driven by stochastic inputs, excitations and disturbances. Some of the considered methods, such as fuzzy and adaptive self--tuning controllers, were already verified on wind turbine systems, and similar advantages may thus derive from their appropriate implementation and application to hydroelectric plants. These issues represent the key features of the work, which provides some guidelines on the design and the application of these control strategies to these energy conversion systems. The working conditions of these systems will be also taken into account in order to highlight the reliability and robustness characteristics of the developed control strategies, especially interesting for remote and relatively inaccessible location of many installations.

Candida albicans as an opportunistic pathogen exploits the host immune system and causes a variety of life-threatening infections. The polymorphic nature of this fungus gives it tremendous advantage to breach mucosal barriers and cause a variety of oral and disseminated infections. Enterococcus faecalis, another opportunistic pathogen co-exists with C. albicans in several niches in the human body, including the oral cavity and gastrointestinal tract. However, interactions between E. faecalis and C. albicans on oral mucosal surfaces remain unknown. Here, for the first time, we comprehensively characterized the interactive profiles between laboratory and clinical isolates of C. albicans (SC5314 and BF1) and E. faecalis (OG1RF and 846) on an organotypic oral mucosal model. Our results demonstrated that the two species formed robust biofilms on the mucosal tissue surface with profound surface erosion and fungal invasion. Specifically, this effect was more pronounced in the laboratory isolates than in the clinical isolates. Notably, several genes of C. albicans involved in tissue adhesion, hyphal formation, fungal invasion, and biofilm formation were significantly upregulated in the presence of E. faecalis. This study highlights the strain-dependent cross-kingdom interactions between E. faecalis and C. albicans on oral mucosa, demonstrating the requisite to study more substrate-dependent polymicrobial interactions.

The recent growing attention to energy saving and environmental protection issues has brought to attention the possibility of exploiting syngas from gasification of biomass and coal for the firing of industrial plants included the so called Integrated Gasification Combined Cycle ones. In order to improve the knowledge about the employ of syngas in lean premixed turbulent flames, a large scale swirl stabilized gas-turbine burner has been operated with a simplified model of H₂ enriched syngas from coal gasification. The experimental campaign has been performed at atmospheric pressure with operating conditions derived from scaling the real gas turbines ones. The results are here reported and consist of OH-PLIF measurements carried out at decreasing air equivalence ratio conditions and are analysed together with the mean aerodynamic characterisation of the burner flowfield in isothermal condition. The OH concentration distributions have been analysed statistically in order to obtain information about the location of the most reactive zones and an algorithm has been applied to the data in order to identify the flame fronts. In addition, the flame front locations have been successively interpreted statistically in order to obtain information about their main features and about their dependence on the air to fuel ratio behaviour.

The black-chinned tilapia Sarotherodon melanotheron is the most abundant fish species in the Nakwa (a closed lagoon) and Brenu (an open lagoon) in the Central region of Ghana. Aspects of the life history characteristics and the ecology of the fish populations in both lagoons were studied to assess the bio-ecological status of this important resource. The estimated von Bertalanffy growth parameters were L∞ = 12.04 cm; K =2.76 year-1 for the Nakwa Lagoon samples and L∞ = 13.44 cm; K = 3.27 years-1 for Brenu Lagoon samples. Daily otolith incremental rate ranged from 0.01-0.03mm per day and 0.01-0.02mm per day for Nakwa and Brenu lagoons respectively. Stomach content analysis of the fish samples revealed that the species are planktivorous and the range of food varied between the lagoons. Green algae was the most prevalent food item in the stomachs of the fish samples from Nakwa with frequency of 69% while diatoms (80.5%) were most prevalent phytoplanktonic food item in for the fish in Brenu lagoon. The results of this study of Sarotherodon melanotheron from the two lagoons and can be used to improve on management policies, maximize yield and to sustain the fishery resources.