In this paper, the tensile behavior of unidirectional carbon/epoxy prepreg is experimentally analyzed at varying loads and temperatures, focusing on the considerable nonlinearity at the beginning of the stress-strain curve. The high viscosity of this material presented difficulties in securely holding specimens during tensile testing. As a result, modifications were made to the conventional gripping method to enable the acquisition of reliable test data. Additionally, a longer gauge length was chosen to minimize the impact of slippage on the elastic modulus measurement. To support the experiment, a micromechanical model of a prepreg tow with fiber waviness is proposed. An RVE model of periodically distributed unidirectional waved cylindrical fibers embedded within the matrix is developed to predict the effective material stiffness parameters. Numerical results are presented for different amplitude-to-wavelength ratios which indicate the fiber waviness reduces the tensile modulus of the composite. The simulation results are in good agreement with the uniaxial tensile test of the prepreg tow.

A methodology is proposed for designing the stabilization process of polyacrylonitrile (PAN) fibers. In its core, this methodology is based on a model that describes the characteristic fiber length change during the treatment, through the de-convolution of the three main contributors (i.e. entropic shrinkage, creep, and chemical shrinkage). The model has the additional advantage of offering further insight into the physical and chemical phenomena taking place during the treatment. Validation of PAN-model prediction performance for different processing parameters was achieved as demonstrated by FTIR and DSC. Τensile testing revealed the effect of processing parameters on fiber quality, while model prediction demonstrated that ladder polymer formation is accelerated at temperatures over 200oC. Additionally, according the DSC and FTIR measurements predictions from the application of the model during stabilization seem to be more precise at high-temperature stabilization stages. It was shown that mechanical properties could be enhanced preferably by including a treatment step below 200oC, before the initiation of cyclization reactions. Further confirmation was provided via Raman spectroscopy, which demonstrated that graphitic like planes are formed upon stabilization above 200oC, and thus multistage stabilization is required to optimize synthesis of carbon fibers. Optical Microscopy proved that isothermal stabilization treatment did not severy alter the cross section geometry of PAN fiber monofilaments.

Prebiotic dietary fiber supplements are commonly consumed to help meet fiber recommendations and improve gastrointestinal health by stimulating beneficial bacteria and the production of short-chain fatty acids (SCFAs), molecules beneficial to host health. The objective of this research project was to compare potential prebiotic effects and fermentability of five commonly consumed fibers using an in vitro fermentation system measuring changes in fecal microbiota, total gas production and formation of common SCFAs. Fecal donations were collected from three healthy volunteers. Materials analyzed included: pure beta-glucan, Oatwell (commercially available oat-bran containing 22% oat β-glucan), xylooligosaccharides (XOS), WholeFiber (dried chicory root containing inulin, pectin, and hemi/celluloses), and pure inulin. Oatwell had the highest production of propionate at 12 h (4.76 μmol/mL) compared to inulin, WholeFiber and XOS samples (p<0.03). Oatwell’s effect was similar to those of the pure beta-glucan samples, both samples promoted the highest mean propionate production at 24 h. XOS resulted in a significant increase in the genus Bifidobacterium after 24 h of fermentation (0 h: 0.67 OTUs; 24 h: 5.22 OTUs; p = 0.038). Inulin and WholeFiber increased the beneficial genus Collinsella, consistent with findings in clinical studies. All analyzed compounds were fermentable and promoted the formation of beneficial SCFAs.

An optical frequency comb (OFC) generator based on an electro-optic Talbot laser and cross-phase modulation (XPM) in a high nonlinear fiber (HNLF) is designed and demonstrated. The Talbot laser is an electro-optic frequency shifting loop to produce repetition rate multiplied pulses, and these pulses working as a pump signal induce XPM process in the HNLF to modulate the phase of a probe signal. At the output of the HNLF, OFCs with a multiplied line-spacing can be generated. The effects of the pump power and the HNLF length on the performance of the generated OFCs are theoretically analyzed. In the experiments, the line-spacing of the generated OFCs is respectively multiplied to be 10 GHz, 15 GHz and 20 GHz with a factor of 2, 3 and 4. The center of the OFCs is tuned in a 4-nm range by adjusting the wavelength of the probe signal.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

Glaucoma, a group of diseases characterized by progressive retinal ganglion cell loss, cupping of the optic disc and by a typical pattern of visual field defects, is a leading cause of severe visual impairment and blindness worldwide. Elevated intraocular pressure (IOP) is the leading risk factor for glaucoma development. However, glaucoma can also develop at normal pressure levels. An increased susceptibility of retinal ganglion cells to IOP, systemic vascular dysregulation, endothelial dysfunction and autoimmune imbalances have been suggested to play a role in the pathophysiology of normal tension glaucoma. Since inflammation and oxidative stress play a role in all forms of glaucoma, the goal of this review article is to resent an overview on the inflammatory and prooxidant mechanisms in the pathophysiology of glaucoma and to discuss immunomodulatory and antioxidant treatment approaches.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

The purpose of this study was to analyze the influence of Chitosan 0.2% in various final cleaning methods on the bond strength of fiberglass post (FP) to intrarradicular dentin. Ninety bovine incisors were sectioned to obtain root remnants measuring 18 mm in length. The roots were divided: G1: EDTA 17%; G2: EDTA 17% + PUI; G3: EDTA 17% + EA; G4: EDTA 17% + XPF; G5: Chitosan 2%; G6: Chitosan 2% + PUI; G7: Chitosan 2% + EA; G8: Chitosan 2% +XPF. After carrying out the cleaning methods, the posts were installed, and the root cleaved to to generate two disks from each root third. Bond strength values (MPa) obtained from the micro push-out test data were assessed by Kruskal-Wallis and Dwass-Steel-Critchlow-Fligner tests for multiple comparisons (α = 5%). Differences were observed in the cervical third between G1 and G8 (p=0.038), G4 and G8 (p=0.003), G6 and G8 (p=0.049), and Control and G8 (p=0.019). The final cleaning method influenced the adhesion strength of cemented FP to intrarradicular dentin. Chitosan 0.2% + XPF positively influenced adhesion strength, with the highest values in the cervical third.

Optical networks, characterized by using optical fibers as a transmission medium, constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is one of the key factors influencing optical network performance, it is important to comprehend its limitations and have the capability to estimate its value. In this context, we revisit the concept of capacity from various perspectives, including channel capacity, link capacity, and network capacity, thus providing an integrated view of the problem. Hence, we review the fundamental concepts behind optical networks, along with the basic physical phenomena present in optical fiber transmission and provide methodologies for estimating the different types of capacities, mainly using simple formulations. In particular, we propose a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with capacitated routing techniques for traffic routing. We apply this method to three reference networks and obtain capacities ranging from tens to hundreds of Terabits/s. Whenever possible, we also compare our results with published experimental data to understand how they relate.

With the development of the volume of information exchange and perception increases, the demands for intelligent, miniaturized and integrated optical devices for information acquisition are also increasing. As the core component of optical networks for transmitting information, how to further optimize its structural characteristics to generate richer optical characteristics and apply them to information exchange and optical field control has become a key research hotspot. The introduction of chiral twist characteristics has led to new phenomena and applications in optical field transmission and transformation for traditional optical fibers or microstructured optical fibers (MOF). Therefore, this review mainly starts from the principle of chiral optical fibers, introduces their preparation and latest application scenarios, and finally looks forward to their potential future development prospects.

The reinforcing effect of boehmite nanoparticles (BNP) in epoxy resins for fiber composite lightweight construction is related to the formation of a soft but bound interphase between filler and polymer. The interphase is able to dissipate crack propagation energy and consequently increases the fracture toughness of the epoxy resin. Usually, the nanoparticles are dispersed in the resin and then mixed with the hardener to form an applicable mixture to impregnate the fibers. If one wishes to locally increase the fracture toughness at particularly stressed positions of the fiber-reinforced polymer composites (FRPC), this could be done by spraying nanoparticles from a suspension. However, this would entail high costs for removing the nanoparticles from the ambient air. We propose that a fiber fleece containing bound nanoparticles be inserted at exposed locations. For the present proof-of-concept study, an electrospun polycarbonate nonwoven and taurine modified BNP are proposed. After fabrication of suitable PC/EP/BNP composites, the thermomechanical properties were tested by dynamic mechanical analysis (DMTA). Comparatively, the local nano-mechanical properties such as stiffness and elastic modulus were determined by atomic force microscopy (AFM). An additional investigation of the distribution of the nanoparticles in the epoxy matrix, which is a prerequisite for an effective nanocomposite, is carried out by scanning electron microscopy in transmission mode (TSEM). From the results it can be concluded that the concept of carrier fibers for nanoparticles is viable.

Mandibular critical size defect (CSD) due to pathological conditions, trauma, and congenital disease can not heal spontaneously and predominantly filled with fibrous tissue. Therefore, a Guided Bone Regeneration (GBR) combined with bone grafting can be performed. The researchers considered using Demineralized Dentin Material Membrane (DDMM) from bovine dentine as an alternative GBR. This study aimed to determine the amount of fibroblast and collagen density after DDMM and bone graft implantation on CSD. Thirty-six Rattus norvegicus rats were used as samples. Mandibular bone defect 5x5 mm was made, then filled with bone graft and covered with Bovine Pericardium Collagen Membrane (BPCM) in the control group and DDMM in the treatment group. Six samples were sacrificed on 7, 14, and 21 days post-surgical for histology examination. There were no significant differences in the amount of fibroblast and collagen density (p-value > 0,05). The amount of fibroblast is lower and the collagen density is higher in treatment group. DDMM has microporosity to prevent connective tissue ingrowth and dentine tubules to allow growth factors release. DDMM and bone graft implantation can reduce the amount of fibroblasts and increase collagen density of CSD which potentially being used as a CSD alternative treatment for bone regeneration.

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO2-coated and Fe2O3-coated carbon fibers were used as the cathode and the anode materials, respectively. FE-SEM analysis confirmed that the CoMnO2-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amounts of ammonium persulfate (APS) as an oxidizing agent, and Fe2O3-coated carbon fiber electrode showed a uniform distribution of porous Fe2O3 nanorods over the surface of carbon fibers. The nanostructured CoMnO2 were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatments. In particular, the electrochemical properties of the CoMnO2-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g-1 at 0.7 A g-1 and good rate capability of 34.8% at 4.9 A g-1. Moreover, the wire-type device displayed the superior energy density of 60.16 Wh kg-1 at a power density of 490 W kg-1 and excellent capacitance retention of 95% up to 3,000 charge/discharge cycles.

The electrical, mechanical and thermal conductivity of ethylene butene copolymer (EBC) composites with carbon fibers were studied. EBC/carbon-fiber composites can be utilized as an electro-mechanical material which is capable of changing it electric resistance with mechanical strain. Carbon fibers were introduced to EBC with different concentrations (5-25 wt%). The results showed that the addition of carbon fibers to EBC could increase the electric resistance up to 10 times. Increasing the load to 2.9 MPa could increase the electric resistance change by 4500% compared 25% fiber sample with pure EBC. It is also noted that the electric resistance of the EBC/CF composites underwent a dramatic increase with raising the strain, for example, the resistance change was around 13 times more at 15% strain in comparison to 5% of strain; The thermal conductivity tests showed that the addition of carbon fibers could increase the thermal conductivity by 40%, from 0.19 to 0.27 (Wm-1K-1). It was also observed that the addition of carbon fibers to EBC could increase the thermal conductivity.

Blending lignin as the second most abundant polymer in nature with nanostructured compounds such as dendritic polymers will not only add value to lignin, but also increase its application in various fields. In this study, softwood Kraft lignin/polyamidoamine dendritic polymer (PAMAM) blends were fabricated by solution electrospinning method to produce bead-free nanofiber mats. The mats were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), zeta potential, and thermogravimetry analysis (TGA). The chemical intermolecular interactions between lignin functional groups and abundant amino groups in PAMAM were investigated by FTIR and viscosity measurement. These interactions enhanced the mechanical and thermal characteristics of lignin/PAMAM mats, providing further potential applications at industry level.

Twelve overnight fasted, healthy, male volunteers received on separate days a test breakfast consisting of (A) 100 g fresh white bread (providing 50 g starch) and 250 mL drinking water, (B) the same bread with a supplement of 10 g alpha-cyclodextrin dissolved in the drinking water (250 mL), and (C) 250 mL drinking water containing 25 g alpha-cyclodextrin. Capillary and venous blood samples were collected before breakfast and at regular intervals for a period of 3 hours thereafter. Plasma glucose was determined in capillary blood and plasma insulin in venous blood samples. Breakfast (A) let to the expected rise in blood glucose and insulin concentrations. Breakfast (C) did not produce a significant glycemic and insulinemic response, demonstrating that alpha-cyclodextrin is not hydrolyzed to glucose in the human digestive tract. Mild intestinal symptoms after the ingestion of alpha-cyclodextrin were reported by 4 subjects. The postprandial rises of plasma glucose and insulin were significantly smaller after breakfast (B) than (A). Under the conditions of this study, alpha-cyclodextrin reduced the glycemic and insulinemic index of white bread by 57 and 55 %, respectively. The postprandial time profile of plasma glucose and insulin suggests that, in an initial phase, the digestion of starch is inhibited by alpha-cyclodextrin almost completely. Yet, despite the delayed and reduced digestion of starch, the intake of breakfast (B) was not associated with flatulence or any other gastrointestinal symptoms.

In this paper, first the Self-Written Waveguide (SWW) process in wet photopolymer media (liquid solutions), are examined for three examples: single-, counter-, and co-fibers exposure. Then the SWWs formed inside solid material are examined including the effects of manipulating the alignment of the fibers. In all cases high precision measurements are used to position the fiber optic cables (FOCs) before exposure using a microscope. The self-writing process is indirectly monitored by observing (imaging) the light emerging from the side of the material sample during SWW formation. In this way the optical waveguide trajectories formed in an Acrylamide/Polyvinyl Alcohol (AA/PVA) a photopolymer material (sensitized at 532 nm) are examined. First the transmission of light by this material is characterized. Then the bending and merging of the waveguides which occur are investigated. The predictions of our model are shown to qualitatively agree with the observed trajectories. The largest index changes taking place at any time during the exposure, i.e. during SWW formation, are shown to take place at the positions where the largest exposure light intensity is present. Typically, such maxima exist close to the input face and the first maximum is referred to as the location of the Primary Eye. Other local maxima also appear further along the SWW and are referred to as Secondary Eyes, i.e. deeper within the material.

The proper hydrogenation of Hyper-coal (HPC) using 1, 2, 3, 4-tetrahydroquinoline (THQ) was able to decrease the oxygen content and adjust the molecular structure of HPC for preparing the spinnable pitch with high softening point (SP). The spinnable pitch prepared from the THQ-soluble (QS) fraction of HPC as a precursor consisted more naphthenic carbon groups than that prepared from the 1-methylnaphthalene (1-MN) soluble (MNS) fraction of HPC. The HPC-QS derived pitch showed excellent spinnability even the SP of 260°C, and the tensile strength of the resultant carbon fiber was up to 1350 MPa with a diameter around 8 µm by only heat treatment at 800°C for 5 min.

Polymer-derived SiC-polycrystalline fiber (Tyranno SA) shows excellent heat-resistance up to 2000^oC, and relatively high strength. Up to now, through our research, the relationship between the strength and residual defects of the fiber, which were formed during the production processes (degradation and sintering), has been clarified. In this paper, we addressed the relationship between the production condition and the surface roughness of the obtained SiC-polycrystalline fiber, using three different raw fibers (Elementary ratio: Si₁Al_0.01C_1.5O_0.4~0.5) and three different types of reactor (Open system, Partially-open system, and Closed system). With increase in the oxygen content in the raw fiber, the degradation during the production process easily proceeded. In this case, the degradation reactions (SiO+2C=SiC+CO and SiO₂+3C=SiC+2CO) in the inside of each filament become faster, and then the CO partial pressure on the surface of each filament is considered to be increased. In consequence, according to Le Chatelier’s principle, the surface degradation reaction and grain growth of formed SiC crystals would be considered to become slower. That is to say, using the raw fiber with higher oxygen content and closed system (highest CO content in the reactor), much smoother surface of the SiC-polycrystalline fiber could be achieved.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

The present study investigates the failure mechanisms of industrial fiber materials, using a custom designed fiber cutting performance test bench. The fracture morphologies of single PA6 fibers are examined by scanning electron microscopy. The analysis reveals that fiber cutting can be distinguished according to four distinct stages of fiber failure represented by shearing, cutting, brittle fracture, and tensile failure, which are the result of different mechanisms active during the processes of crack initiation, extension and fracture. The results of fractographic analysis are further verified by an analysis of the blade assembly speed with respect to time over the entire fracture failure process based on high-speed camera data. The results of fractographic analysis and blade assembly speed are fully consistent.

Burn patients still represent an important challenge in critical care medicine today. These patients can develop significant neurological conditions up to intracranial hypertension, but as they find themselves hospitalized outside of neurocritical care and are often subjected to sedation for the complex management, they are sometimes underestimated. The aim of this study is to evaluate the feasibility of non-invasive methods for the early diagnosis of intracranial hypertension in these patients. In this prospective observational study, adult burn patients admitted to intensive care within the first 8 hours of the event were enrolled. These patients were studied through ultrasound measurement of optic nerve sheath diameter and intracranial vessel velocimetry with transcranial Doppler. In the 20 patients studied, no frankly pathological values were identified in the 3 different measurement stages (within 8 hours of the burn, then at 48 and 96 hours) and no correlations were identified between the measured values and the extension of the burn with the related risk of mortality. However, this study, one of a kind, demonstrates that these non-invasive methods are applicable to this specific patient population, and can represent an effective method for reducing the incidence of complications that are dangerous for survival.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

Purpose: To investigate the relationship of lamina cribrosa displacement to corneal biomechanical properties and visual function after mitomycin C-augmented trabeculectomy. Method: Eighty-one primary open angle eyes were imaged before and after trabeculectomy using an enhanced depth spectral-domain optical coherence tomography (SDOCT). Corneal biomechanical properties were measured with the Ocular Response Analyser before the surgery. The anterior lamina cribrosa (LC) was marked at several points in each of six radial scans to evaluate LC displacement in response to Intraocular pressure (IOP) reduction. A Humphrey visual field test (HVF) was performed before the surgery as well as three and six months postoperatively. Results: Factors associated with a deeper baseline anterior lamina cribrosa depth (ALD) were cup-disc ratio (P=0.04), baseline IOP (P= 0.01), corneal hysteresis (P= 0.001), and corneal resistance factor (P= 0.001). After the surgery, the position of LC became more anterior (negative), posterior (positive) or remained unchanged. The mean LC displacement was -42 μm (P= 0.001) and was positively correlated with the magnitude of IOP reduction (regression coefficient: 0.251, P=0.02), and negatively correlated with age (regression coefficient: - 0.224, P= 0.04) as well as baseline cup-disk ratio (Regression coefficient: -0.212,P= 0.05) Eyes with a larger negative LC displacement were more likely to experience an HVF improvement of more than 3 dB gain in mean deviation (P= 0.002). Conclusion: A lower SDOCT cup-disc ratio, younger age, and a larger IOP reduction were correlated with a larger negative LC displacement and improving HVF. Corneal biomechanics did not predict LC displacement.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

A total internal reflection photonic crystal fiber (PCF) based on hexagonal core is proposed for gas sensing in a specific wavelength range. The higher sensitivity and lower confinement loss were realized by the structure of the proposed PCF consists of two layers with circular holes rotated hexagonally around a core region and six slotted air-hole in the cladding based on numerical analysis. The simulation results show that the enhancement of the relative sensitivity has been done by enhancing the diameter of the hexagonal shape air-hole cladding (d1) and the hexagonal arranged holes around the central solid core (d0) in this design. Also, the confinement loss has been reduced by enhancing the ratio of length to width of slotted holes (l/w) and decreasing the cladding air-hole diameters (d1). As the refractive index increases, the wavelength shifts toward the long wavelength. And in a certain temperature range, the transmission characteristics of the device does not change with the temperature. The results are helpful for designing high performance PCF for gas sensing applications.

Dietary fiber has been associated with health benefits, therefore, the availability of validated tools to assess food consumption associated with high-fiber foods would allow the quantification of the intake of this functional nutrient, the identification of risk groups and target populations, and the development of public policies and/or programs aimed at improving the health of the population. In this study, a fiber intake short food frequency questionnaire (FFQ) was translated into Spanish and its content validity was determined by a group of experts, to subsequently conduct a pilot test including 198 subjects aged 36+12.5 years, residing in Chile (46 men and 150 women), with the purpose of quantifying dietary fiber intake. The global assessment of the FFQ revealed a validity coefficient of 0.98+0.02; after the application of the pilot, mean dietary fiber intake in adult Chilean residents was of 13 g per day, with similar results to those found in the National Food Consumption Survey 2010 (12.5 g per day in men, and 11.5 g in women). The FFQ is a quick and valid tool to classify people on the basis of their habitual dietary fiber intake.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Cytochrome P450 (CYPs) is a functionally diversified third-largest gene family that exploded in the plant kingdom. Their role in different organ development has been illustrated by the intervention of phytohormone. Cotton is a model organism for cell differentiation and cell elongation. To decipher the participation of CYPs in different cotton fiber developmental stages, we identified and characterized 2460 CYPs in three diploids and two allotetraploid cottons. Furthermore, In-silico expression and cluster analysis of cotton CYPs was conducted to distinguish the fiber stage-specific clusters that have the determining role in different stages of fiber development. The subgenome expression of two conserved Gossypium hirsutum CYPs, namely, GhCYP78A197 and GhCYP78A198 contributed to fiber initiation at an early stage of fiber development, governed by the co-occurrence of TATA and MYB TFs binding sites. Coexpression network partners of these two GhCYP78A annotated as auxin, kinases, chromatin remodeler, epigenetic regulator and cyclin-related genes that possibly induce the endoreduplication and cell proliferation for fiber cell initiation to define the high yield and biomass.

Consumption of prebiotic fibers to modulate the human gut microbiome is a promising strategy to positively impact health. Nevertheless, given the compositional complexity of the microbiome and its inter-individual variances, generalized recommendations on the source or amount of fiber supplements remain vague. This problem is further compounded by availability of tractable in vitro and in vivo models to validate certain fibers. We employed a gnotobiotic mouse model containing an a priori characterized 14-member synthetic human gut microbiome (SM) for their ability to metabolize a suit of fibers in vitro; the SM contains 14 different strains belonging to five distinct phyla. Since soluble purified fibers have been a common subject of studies, we specifically investigated the effects of concentrated raw fibers (CRFs)—containing fibers from pea, oat, psyllium, wheat and apple—on the compositional and functional alterations in the SM. We demonstrate that, compared to a fiber-free diet, CRF supplementation increased the abundance of fiber-degraders namely Eubacterium rectale, Roseburia intestinalis and Bacteroides ovatus and decreased the abundance of the mucin-degrader Akkermansia muciniphila. These results were corroborated by a general increase of bacterial fiber-degrading α-glucosidase enzyme activity. Overall, our results highlight the ability of CRFs to enhance the microbial fiber-degrading capacity.

The distributed long-range sensing system using the standard telecommunication single-mode optical fiber in a function of a distributed sensor for sensing of mechanical vibrations is described. Various events generating vibrations such as walking or running person, moving cars, trains and others can be detected, localized and classified. The sensor and related sensing system components were designed and constructed and the system was tested both in the laboratory and in the real situation with 88 km telecom optical link, and the results are presented.

In the past decades, Fiber Reinforced Concrete has been gaining more attention in the concrete research development. There are many advantages of the inclusion of fiber into reinforced concrete structures. It was found that the inclusion of fibers in concrete, be it synthetic or natural, resulted in the improvement of the thermal properties of concrete, as well as its strength to some extent. However, the inclusion of fibers in concrete does affects its thermo-mechanical properties. The objective of this study is to identify the potential of the addition Polypropylene and Kenaf fibers in cement mortar at different compositions (0.1%, 0.2%, and 0.3%). Eight mixes were analyzed for this purpose. Upon investigating the flow ability, compressive strength, tensile strength, and thermal conductivity of the mortar samples, it was found that the incorporation of PP and Kenaf fibers reduced the flow ability. Cement mortar samples containing 0.1% addition of PP and Kenaf fibers show the highest compressive strength compared to other percentages, while samples containing 0.3% addition of PP and Kenaf fibers show the highest tensile strength compared to other percentages. The thermal conductivity of mortar samples shows reduction when high percentages of both fibers were used.

Extinction of natural resources builds up pressure on governments to invest in research to find more sustainable resources for construction sector. Earlier studies on mortar and concrete show that bottom ash and basalt fiber are independently alternative binder in the concrete sector. This study aims to use bottom ash and basalt fiber blends as alternative novel-based composites in pure cement paste. Strength and durability properties of two different percentages of bottom ash (40% and 50%) and three volume fractions of basalt fiber (0.3%, 0.75%, and 1.5%) were used at three curing periods (7, 28, and 56 days). In order to measure physical properties of the basalt-reinforced bottom ash cement paste composites flowability, dry unit weight, porosity and water absorption measurements at 7, 28, and 56 days of curing were performed. Furthermore, mechanical properties of composites determined by unconfined compressive strength and flexural strength tests. Finally, to assess the durability sulfate-resistance and seawater-resistance tests have been performed on composites at 28 and 56 days of curing. Results showed that addition of basalt fiber improves physical, mechanical and chemical stability properties of paste up to a limiting basalt fiber addition (0.3% volume fraction) where above an adverse effect have been monitored. It is clear that observed results can lead to development of sustainability strategies in the concrete industry by utilizing bottom ash and basalt fiber as an alternative binder.

Type-2 fuzzy sets were introduced by L. Zadeh aiming at modelling some settings in which fuzzy sets (usually called type-1 fuzzy sets) are not sufficient to reflect certain uncertainty degrees - loosely speaking, they are fuzzy sets whose membership degrees are ordinary fuzzy sets. On the other hand, fiber bundles are topological entities of extreme importance in Mathematics itself and many other scientific areas, like Physics (General Relativity, Field Theory etc.), finance modelling, and statistical inference. The present work introduces a conceptual link between the two ideas and conjectures about the potential mutual benefits that can be obtained from this viewpoint.As an objective and usable product of the presented ideas, it is described a framework for defining type-2 fuzzy hedges, proper to operate on interval type-2 fuzzy sets.

A multiscale modelling approach was developed in order to estimate the effect of defects on the strength of unidirectional carbon fiber composites. The work encompasses a micromechanics approach, where the known reinforcement and matrix properties are experimentally verified and a 3D finite element model is meshed directly from micrographs. Boundary conditions for loading the micromechanical model are derived from macroscale finite element simulations of the component in question. Using a microscale model based on the actual microstructure, material parameters and load case allows realistic estimation of the effect of a defect. The modelling approach was tested with a unidirectional carbon fiber composite beam, from which the micromechanical model was created and experimentally validated. The effect of porosity was simulated using a resin-rich area in the microstructure and the results were compared to experimental work on samples containing pores.

The addition of flaxseed and amaranth on the physicochemical, functional and microstructural changes of instant-extruded cereals was evaluated. Six different mixtures were made with additions of amaranth (30%–50%) and flaxseed (10% and 15%) using maize grits and minor additives as supplementary ingredients and then extruded in a twin-screw extruder. The extrudates evaluated, had insoluble and soluble fiber contents increased with the proportion of amaranth and flaxseed. The mixture 4 (higher flaxseed content) presented highest soluble fiber percentage (1.9%). Extruded cereals had the lowest viscosity (<99.5 cp) and highest hardness values (5.2 N) whereas the dietary fiber content was highest. Fiber content increase, resulted in a higher water solubility index (WSI) (0.5) and decrease the water absorption index (WAI) (2.5). Amaranth and flaxseed incorporation increased crystallinity, resulting in a larger, and more compact laminar structure. Amaranth and flaxseed addition resulted in extruded cereals with acceptable physicochemical and functional properties.

Two isotropic pitches were prepared by air blowing and nitrogen distillation method using ethylene tar (ET) as a raw material. And correspondent carbon fibers were obtained through conventional melt spinning, stabilization and carbonization. The structures and properties of resultant pitches and fibers were characterized and their differences were discussed in this work. The results showed that introduction of the oxygen by air blowing method could quickly increase the yield and softening point of pitch. Moreover, the air blown pitch (ABP) composed of linear methylene chains of aromatic molecules while the nitrogen distilled pitch (NDP) mainly contained polycondensed aromatic rings, which was due to the oxygen containing functional groups existed in ABP could impede order stack of pitch molecules and form methylene bridge structure, instead of aromatic condensed structure like NDP. Meanwhile, the spinnability of ABP was not decreased even containing 2.31 wt% oxygen. In contrast, ABP had narrower molecular weight distribution, which contributed to better stabilization properties and higher tensile strength of carbon fiber. The tensile strength of carbon fibers from ABP was reached to 860 MPa with fiber diameter of about 10 μm, which was higher than that of NDP-derived carbon fibers of 640 MPa.

Being able to forecast events is of great importance in many fields, from brain behavior to earthquakes or stock markets. Because each dynamical system has intrinsic features, different statistical tools have to be used for each system. Here we study the time series of the output intensity of a fiber laser with an ordinal patterns analysis, and we look for temporal correlations in order to statistically forecast the most intense events. We set two thresholds, a low one and a high one, to distinguish between low intensity versus high intensity events. We find that when the time series is performing events below the low threshold it shows some preferred temporal patterns before performing events above a high threshold.

For development and successful application of any material, a clear understanding of their mechanical behavior is one of the most important things, but when it comes to nanofibers networks it become a challenge due to, their high porosity, many scales in their structure, and characteristics non-linear. Therefore, an experimental methodology in conjunction with a theoretical model that can fully consider their characteristics is still needed. In this work we proposed a model that incorporates the propagation of the elastic waves in two-phase media to determine the effective elastic modulus of electrospun membranes of PLA/gelatin given the mechanical properties of nanofibers, shape, distribution and concentration. The model was verified via laser ultrasonic testing. It was found that the values predicted for the effective modulus by the model were higher than the values obtained from experimental results. One explanation is due to the experimental density. As a result, the P-Wave velocity from the model best fit to experimental results and it has the same behavior, decrees as the concentration of gelatin in the solution. These results indicate the model and experimental methodology can assist in the dressing of nanofibers networks and electrospun materials.

A novel 8-channel demux device based on multicore photonic crystal fiber (PCF) structures that operate at C-band range (1530-1565nm) has been demonstrated. The PCF demux design is based on replacing some air-holes areas with lithium niobate and silicon nitride materials over the PCF axis alongside with the appropriate optimizations of the PCF structure. The beam propagation method (BPM) combined with Matlab codes were used to modeled the demux device and to optimized the geometrical parameters of the PCF structure. Simulation results show that 8-channel can be demultiplexing after light propagation of 5 cm with large bandwidth (4.03-4.69nm) and crosstalk ((-16.88)-(-15.93) dB). Thus, the proposed device has a great potential to be integrated in dense wavelength division multiplexing (DWDM) technology for increasing performances in networking systems.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

Peripapillary intrachoroidal cavitation (PICC) is a yellow-orange lesion, located at the outer border of the myopic conus. First described as a localized detachment of the retinal pigment epithelium, its intrachoroidal location was later disclosed, justifying its current name. PICC is related to other myopic complications like posterior staphyloma, but its pathogenesis is not clear to date. Although it has been considered a benign condition, most eyes with PICC show visual field defects, leading to diagnostic uncertainty as these deficits resemble those observed in glaucoma. Furthermore, eyes with PICC can develop macular detachment with retinoschisis. Finally, misdiagnosis of PICC as a metastatic choroidal tumor may lead to unnecessary and anxiety-provoking investigation. Advances in optical coherence tomography (OCT) imaging have improved the visualization of ocular structures, contributing to the understanding of PICC. Recently high optic nerve sheaths traction forces during eye movements in highly myopic eyes have been suggested as promoters of PICC, renewing interest around this condition. However, a review of PICC is still lacking. Therefore, we aimed to provide a concise yet comprehensive overview of the current state of the art, focusing on OCT documentation, pathophysiology and potential future perspectives based on biomechanics of the optic nerve.

Background. In the last decade, it was concluded that glaucomatous optic neuropathy is part of the neurodegenerative diseases in which destructive neuronal lesions are located not only in the structure of the retina, but they are also present at the level of the central visual and nervous pathways. Patients with Primitive Open Angle Glaucoma may have experienced changes such as sensorineural hearing loss as well as balance changes. The purpose of this study is to evaluate the degree of involvement of the auditory system in patients with glaucoma, the structural changes in the optic nerve and, to establish correlation between the hearing loss and structural changes in the optic nerve. The subjects included in the study are grouped as follows: a group of patients with glaucoma that will be compared to a group of patients without glaucoma only as well as identi-fy-ing the evolution of structural changes in optic nerve to patients with glaucoma and to normal patients. Material and methods. It is a prospective, cross-sectional study on 32 eyes of 16 subjects with Primitive Open Angle Glaucoma in a study group and 24 eyes of 12 healthy subjects in con-trol group with a mean age of 62 years in both groups. Both groups underwent ophthalmo-logical, audiological and radio imaging evaluation: Pure-tone audiometry (PTA) were recorded, oph-thalmologic evaluations according to a standardized protocol and MRI cerebral examination was performed. Results: In the Study group patients, compared to the Control group, the average lev-els of the left PTA, the cup/disc (C/D) area in both eyes, the C/D ratio in both eyes are in-creased. The mean level of Retinal nerve fiber layer (RNFL) mean thickness was slightly lower in patients with glaucoma. Multivariate analysis demonstrates that gender can be a good predictor of C/D area, gender and age can be good predictors of PTA both eyes and C/D ratio in the right eye, and gender, age and background can be good predictors of disc area in the left eye. Conclu-sions: Pa-tients with Primitive Open Angle Glaucoma show changes in audiometry test in correla-tion with ophthalmological parameters demonstrating that the auditory system can be affected in Primitive Open Angle Glaucoma. This study emphasizes the problem of interdisciplinarity in medicine with the aim of ensuring the quality of life of patients with glaucoma. A good collabora-tion between ophthalmologist and otolaryngologist will be very useful for these patients.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

Visible light communication (VLC) can offer the advantages of license and electromagnetic interference (EMI) free wireless transmission. As optical signal does not interference with the radio-frequency (RF) signal, VLC can be used to augment RF wireless communication to provide extra communication capacity while without degrading the performance of both signals. In order to achieve high performance VLC transmission, optical alignment between the optical transmit (Tx) and receiver (Rx) is very critical to enhance the received signal-to-noise ratio (SNR). Optical beam-steering at the Tx can be utilized to ensure narrow optical beam can reach the Rx; however, complicated and active tracking are required. Lenses or compound parabolic concentrators (CPCs) can be install in front of the Rx for focusing to enhance the SNR. However, these will limit the Rx field-of-view (FOV) and making the VLC transmission more subjected to misalignment issue. Hence, many creative optical antennas have been proposed and demonstrated using special optical materials as well as special Rx to enhance the FOV of VLC systems. However, they have their limitations, such as data rates and FOVs. In this work, we put forward and demonstrate a bi-direction free-space VLC system supporting multiple moveable Rxs using a light-diffusing optical fiber (LDOF). The downlink (DL) signal is launched from an head-end or central office (CO) far away to the LDOF at the client side via a free-space transmission. When the DL signal is launched to the LDOF, which acts as an optical antenna to re-transmit the DL signal to different moveable Rxs. The uplink (UL) signal is sent via the LDOF towards the CO. In a proof-of-concept demonstration, the LDOF is 100 cm long and the free space VLC transmission between the CO and the LDOF is 100 cm. 210 Mbit/s DL and 850 Mbit/s UL transmissions, meeting the pre-forward-error-correction bit error rate (pre-FEC BER = 3.8 × 10−3) threshold are achieved.

Direct measurement of strain within muscle is important for understanding muscle function in health and disease. Current technology (kinematics, dynamometry, electromyography) provides limited ability to measure strain within muscle. Regional fiber orientation and length are related with active/passive strain within muscle. Currently, ultrasound imaging provides the only non-invasive means of observing regional fiber orientation within muscle during dynamic tasks. Previous attempts to automatically estimate fiber orientation from ultrasound are not adequate, often requiring manual region selection, feature engineering, providing low-resolution estimations (one angle per muscle), and deep muscles are often not attempted. Here, we propose deconvolutional neural networks (DCNN) for estimating fiber orientation at the pixel-level. Dynamic ultrasound images sequences of the calf muscles were acquired (25 Hz) from 8 healthy volunteers (4 male, ages: 25–36, median 30). A combination of expert annotation and interpolation/extrapolation provided labels of regional fiber orientation for each image. We then trained DCNNs both with and without dropout using leave one out cross-validation. Our results demonstrated robust estimation of regional fiber orientation with approximately 3° error, which was an improvement on previous methods. The methods presented here provide new potential to study muscle in disease and health.

Magneto-optic (MO) imaging and sensing are at present the most developed practical applications of thin-film MO garnet materials. However, future component and system-level sensors and imagers technology improvements are still necessary in order to improve sensitivity for a range of established and also the forward-looking applications. These improvements are expected to originate from new material system development. We propose a set of technological modifications for the RF-magnetron sputtering deposition and crystallization annealing of magneto-optic bismuth-substituted iron-garnet films and investigate the improved material properties. Results show that standard crystallization annealing for the as-deposited ultrathin (sputtered 10 nm thick, amorphous phase) films resulted in more than a factor of two loss in the magneto-optical activity of the films in visible spectral region, compared to the liquid-phase grown epitaxial films. Results also show that an additional 10 nm-thick metal-oxide (Bi2O3) protective layer above the amorphous film results in ~2.7 times increase in the magneto-optical quality of crystallized iron-garnet films. On the other hand, the effects of post-deposition oxygen (O2) plasma treatment on the magneto-optical (MO) properties of Bismuth substituted iron garnet thin films material is investigated. Results show that, in the visible part of the electromagnetic spectrum (at 532 nm), the O2 treated (up to 3 minutes) garnet films retain higher specific Faraday rotation and figure of merit than those of non-treated garnet films.

Knowing the mechanical properties of fibrous composite materials used in aeronautical industry from the design phase is a primary objective for designers. There are many methods for determining them, but they are laborious and require a long calculation time. And some of the methods are very approximate, giving only upper and lower bounds for these values. Experimental measurements also consume time and others resources. A method for sufficiently accurate and quickly obtained estimation of the engineering constants of the homogenized material is presented in the work. FEM is used to determine the natural frequencies of a standard bar, for which there are sufficiently precise classical methods for expressing these constants according to the properties of the homogenized material. In this way, these sought constants can be determined. In the work, Young's modulus will be determined for such a material, using the relationships that provide the proper pulsations for the longitudinal vibrations. Within the adopted model, transverse and torsional vibrations will be eliminated by blocking the nodes on the surface of the bars. In this way, more longitudinal self-pulsations can be obtained, so the precision in calculating the Young's modulus will increase.

As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer com-posites are being considered as alternative materials in the automobile industry. Rapid impregnation of the resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manu-facturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed

A novel simplifying Volterra structure algorithm is proposed for intensity modulation direct detection (IM-DD) optical fiber short distance communication system by using the decision feedback equalization algorithm (DFE). Based on this algorithm, the signal damage for four-level pulse amplitude modulation signal (PAM-4) is compensated, which is caused by device bandwidth limitation and dispersion during transmission. Experiments have been carried out using a 25GHz Electro-absorption Modulated Laser (EML), showing that PAM-4 signals can transmit over 10km in standard single-mode fiber (SSMF). The 112Gbps and 128Gbps signals can reach the error rate threshold of KP4-FEC (BER=2*10-4) and HD-FEC (BER=3.8*10-3), respectively. The simplified principle and process of proposed Volterra-based equalization algorithm are presented. Experimental results show that the algorithm complexity is greatly reduced by 75%, which provides an effective theoretical support for the commercial application of this algorithm.

Carbon fiber insole (CFI), which is lightweight and stiff to reduce energy loss and help wearers perform better in sports, has recently been introduced. However, there are scarce reports on the effects of CFI on sports performance, muscle fatigue and wearing comfort. This study investigat-ed the short-term effects of CFI on sports performance, lower extremity muscle activity, and sub-jective comfort. Thirty young healthy males performed various sports tasks and treadmill runs with wearable sensors under two experimental insole conditions (benchmark insole as a baseline, CFI). The results showed that compared to the benchmark insole, CFI significantly improved sports performance in terms of power generation and agility. However, it activated more of the Tibialis Anterior and Gastrocnemius Medialis muscles and was perceived stiffer, and less com-fortable. These findings suggested that CFI can improve sports performance, but it could cause more lower extremity muscle fatigue and subjective discomfort.

For the numerical simulation of components made of short fiber-reinforced composites the correct prediction of the deformation including the elastic and plastic behavior and its spatial distribution is essential. When using purely deterministic modeling approaches the information of the probabilistic microstructure is not included in the simulation process. One possible approach for the integration of stochastic information is the use of random fields. In this study numerical simulations of tensile test specimens are conducted utilizing a finite deformation elastic-ideal plastic material model. A selection of the material parameters covering the elastic and plastic domain are represented by cross-correlated second-order Gaussian random fields to incorporate the probabilistic nature of the material parameters. To validate the modeling approach tensile tests until failure are carried out experimentally, that confirm the assumption of spatially distributed material behavior in both the elastic and plastic domain. Since the correlation lengths of the random fields cannot be determined by pure analytic treatments, additionally numerical simulations are performed for different values of the correlation length. The numerical simulations endorse the influence of the correlation length on the overall behavior. For a correlation length of 5mm a good conformity with the experimental results is obtained. Therefore, it is concluded, that the presented modeling approach is suitable to predict the elastic and plastic deformation of a set of tensile test specimens made of short fiber-reinforced composite sufficiently.

As use of composite materials increases, the search for suitable automated processes gains relevance to guarantee production quality by ensuring uniformity of the process, minimizing the amount of generated scrap and reducing time and energy consumption. Limitations on production by traditional means such as hand lay-up, vacuum bagging and in-autoclave methods, tend not to be as efficient when the size and shape complexity of the part being produced increases, motivating the search for alternative processes such as the Automated Tape Laying (ATL). This work aims to describe the process of modelling and simulating a composite ATL with in situ consolidation by characterizing the machine elements, using the finite differences method in conjunction with energy balances, in order to create a digital twin of the process for further control design. The modelling approach implemented is able to follow the process dynamics when changes to the heating element are imposed as well as to predict the composite material temperature response, making it suitable to work as a digital twin of a production process using an ATL machine.

The booming wearable market and recent advances in material science has led to the rapid development of the various wearable sensors, actuators, and devices that can be worn, embedded in fabric or accessories, or tattoos directly onto the skin. Wearable actuators, a subcategory of wearable technology, have attracted enormous interest from researchers in various disciplines and many wearable actuators and devices have been developed in the past few decades to assist and improve people's everyday lives. In this paper, we review the actuation mechanisms, structures, applications, and limitations of recently developed wearable actuators including pneumatic and hydraulic actuators, shape memory alloys and polymers, thermal and hygroscopic materials, dielectric elastomers, ionic and conducting polymers, piezoelectric actuators, electromagnetic actuators, liquid crystal elastomers, etc. Examples of the recent applications such as wearable soft robots, haptic devices, and personal thermal regulation textiles are highlighted. Finally, we point out the current bottleneck and suggest the prospective future research directions for wearable actuators.

Lignocellulosic fibers are widely applied as composite reinforcement due to their properties. The thermal degradation behavior determines the maximum temperature in which the fiber can be applied without significant mass loss. It is possible to determine these temperatures using Thermogravimetric Analysis (TG). In particular, when curves are obtained at different heating rates, kinetic parameters can be determined and more detailed characteristics of the material are obtained. However, every curve obtained at a distinct heating rate demands material, cost, and time. Methods to predict thermogravimetric curves can be very useful in the materials science field and in this sense mathematical approaches are powerful tools if well employed. For this reason, in the present study, curaua TG curves were obtained at three different heating rates (5, 10, 20, and 40 °C.min-1) and Vyazovkin kinetic parameters were obtained. After, the experimental curves were fitted using an artificial neural network (ANN) approach followed by a Surface Response Methodology (SRM). Curves at any heating rate between the minimum and maximum experimental heating rates were obtained with high reliability. Finally, Vyazovkin kinetic parameters were tested again with the new curves showing similar kinetic parameters from the experimental ones. In conclusion, due to the capability to learn from the own data, ANN combined with SRM seems to be an excellent alternative to predict TG curves that do not test experimentally, opening the range of applications.

Abstract: This study was aimed to determine the influence of the volume fraction of steel fibers and on fracture parameters of concrete. Fifty notched steel fiber reinforced concrete (SFRC) beams and ordinary concrete beams with dimensions of 100mm×100mm×515mm were cast and tested via three-point bending test. Among them, the type of steel fiber is milling type (MF), and the volume fraction of steel fiber added is 0%, 0.5%, 0.5%, 1.5%, 1.5%, 2%, respectively. The effects of the steel fiber volume fraction (VF) on the critical stress intensity factor (KIC), fracture energy (GF), the deflection at failure(δ0), the critical crack mouth opening displacement (CMODC) and the critical crack tip opening displacement (CTODC)were studied. Through the analysis of test phenomena and test data such as load-deflection (P-δ) curve, load-crack mouth opening displacement (P-CMOD) curve and load-crack tip opening displacement (P-CTOD) curve following conclusions are drawn: With the increase of steel fiber volume fraction, some fracture parameters increase gradually and maintain a certain linear growth. The gain ratio of fracture parameters increases significantly, and the gain effect is obvious. Through this law of growth, the experimental statistical formulas of fracture energy and critical stress intensity factor are summarized.

A new covered yarn system is proposed in this manuscript by controlling the tension of the spandex elastic yarn drawing.. By analyzing the relationship between the draw ratio and yarn tension, it has been verified that the new tension controlled drawing system is feasible and results in yarns with superior quality and process stability.

The damage caused by global warming is rapidly increasing, and its adverse effects become more evident with each passing day. Although it is known that the use of alternative binder materials in concrete would decrease this negative effect, reluctance to new composites continues. Waste use plays a vital role in sustainability studies. In this study, pure cement paste was prepared and enriched with carbon fiber. This study investigated the wide range of volume fraction of carbon fiber in cement-based composites. Two different industrial wastes, marble dust, and bottom ash were chosen and mixed with cement and four different (0.3%, 0.75%, 1.5%, and 2.5%) carbon fiber volume fractions. Based on physical, mechanical, and durability tests at 7, 28, and 56-days of curing, the composites were resistant to sulfate and seawater attack. The 0.75% carbon fiber addition seems to be an optimum volume percentage beyond which both physical and mechanical properties were adversely affected. The composites with 0.75% carbon fiber have reached 48.4 MPa and 47.2 MPa at 56-days of curing for marble dust and bottom ash mixture groups, respectively.

We propose a 10-Gb/s 64-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes Reinforcement Learning (RL) SARSA based decision method to indicate an effective decision which mitigates nonlinearity. By utilizing RL-SARSA algorithm, the results demonstrate that significant reduction can be obtained in terms of bit error rate.

Machine learning (ML) methodologies have been looked upon recently as a potential candidate for mitigating nonlinearity issues in optical communications. In this paper, we experimentally demonstrate a 40-Gb/s 256-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes support vector machine (SVM) decision method to indicate an effective nonlinearity mitigation. The influence of different impairments in the system is evaluated that includes the influences of Mach-Zehnder Modulator nonlinearities, in-phase and quadrature phase skew of the modulator. By utilizing SVM, the results demonstrated in terms of bit error rate and eye linearity suggest that impairments are significantly reduced and licit input signal power span of 5dBs is enlarged to 15 dBs.

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

Adding steel fibers to concrete improves the capacity in tension-driven failure modes. An example is the shear capacity in steel fiber reinforced concrete (SFRC) beams with longitudinal reinforcement and without shear reinforcement. Since no mechanical models exist that can fully describe the behavior of SFRC beams without shear reinforcement failing in shear, a number of empirical equations have been suggested in the past. This paper compiles the existing empirical equations and code provisions for the prediction of the shear capacity of SFRC beams failing in shear as well as a database of 487 experiments reported in the literature. The experimental shear capacities from the database are then compared to the prediction equations. This comparison shows a large scatter on the ratio of experimental to predicted values. The practice of defining the tensile strength of SFRC based on different experiments internationally makes the comparison difficult. For design purposes, the code prediction methods based on the Eurocode shear expression provide reasonable results (with coefficients of variation on the ratio of tested to predicted results of 27% - 29%). None of the currently available methods properly describe the behavior of SFRC beams failing in shear. As such, this work shows the need for studies that address the different shear-carrying mechanisms in SFRC and its crack kinematics.

Acoustic emission (AE) has proven to be a very useful technique for determining damage in ceramic matrix composites (CMCs). CMCs rely on various cracking mechanisms which enable non-linear stress-strain behavior with ultimate failure of the composite due to fiber failure. Since these damage mechanisms are all micro-fracture mechanisms, they emit stress waves ideal for AE monitoring. These are typically plate waves since for most specimens or applications one dimension is significantly smaller than the wavelength of the sound waves emitted. By utilizing the information of the sound waveforms captured on multiple channels from individual events, the location and identity of the sources can often be elucidated. The keys to the technique are the use of wide-band frequency sensors, digitization of the waveforms (modal AE), strategic placement of sensors to sort the data and acquire important contents of the waveforms pertinent for identification, and familiarity with the material as to the damage mechanisms occurring at prescribed points of the stress history. The AE information informs the damage progression in a unique way which adds to the understanding of the process of failure for these composites. The AE methodology was applied to composites tested in fatigue at different frequencies where identification of when and where AE occurred coupled with waveform analysis leads to source identification and failure progression.

In this paper, a geometric body-centered model to simulate the periodic structure of unidirectional fibrous composites is presented. To this end, three prescribed configurations are introduced to predict in a deterministic manner the arrangement of internal and neighboring fibers inside the matrix. Thus, three different representative volume elements (RVEs) are established. Furthermore, the concept of the interphase has been taken into account, stating that each individual fiber is encircled by a thin layer of variable thermomechanical properties. Next, these three unit cells are transformed in a unified manner to a coaxial multilayer cylinder model. This advanced model includes the influence of fiber contiguity in parallel with the interphase concept on the thermomechanical properties of the overall material. Then, by the use of this model, the authors propose explicit expressions to evaluate the longitudinal and transverse thermal conductivity of this type of composite. The theoretical predictions were compared with experimental results, as well as with theoretical values yielded by some reliable formulae derived from other workers, and a reasonable agreement was found.

The interest in random fiber lasers (RFLs), first demonstrated one decade ago, is still growing and their basic characteristics have been studied by several authors. RFLs are open systems that present instabilities in the intensity fluctuations due to the energy exchange among their non-orthogonal quasi-modes. In this work, we present a review of the recent investigations on the output characteristics of a continuous-wave erbium-doped RFL, with emphasis on the statistical behavior of the emitted intensity fluctuations. A progression from the Gaussian to Lévy and back to the Gaussian statistical regime was observed by increasing the excitation laser power from below to above the RFL threshold. By analyzing the RFL output intensity fluctuations, the probability density function of emission intensities was determined, and its correspondence with the experimental results was identified, enabling a clear demonstration of the analogy between the RFL phenomenon and the spin-glass phase transition. A replica-symmetry-breaking phase above the RFL threshold was characterized and the glassy behavior of the emitted light was established. We also discuss perspectives for future investigations on RFL systems.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

Fiber reinforced thermoplastics (FRTP), which is reinforced with glass or carbon fibers, are used to improve the mechanical strength of injection-molded products. However, FRTP has problems such as the formation of weld lines, the deterioration of the appearance due to the exposure of fibers on the molded product surface, and the deterioration of the strength of molded products due to the fiber orientation in the molded products. We have designed and fabricated an injection mold capable of melt flow control and induction heating and cooling that has the functions of both heating and cooling the injection mold as well as the function of controlling the melt flow direction using a movable core pin. In this study, the above-mentioned mold was used for the molding of carbon fiber reinforced semi-aromatic polyamide. As a result, we found that increasing the heating temperature of the mold and increasing melt flow control volume contribute to the prevention of the generation of a weld line and the exposure of fibers on the molded product surface, as well as to the formation of a flat surface and increased bending strength. The relationships of these results with the carbon fiber orientation in the molded products and the crystallization of semi-aromatic polyamide were also examined in this study.

In the paper we show that the general relativity in recent Einstein-Palatini formulation is equivalent to a gauge field. We begin with a bit of information of the Einstein-Palatini formulation and derive Einstein field equations from it. In the next section, we consider general relativity with a positive cosmological constant in terms of the corrected curvature. We show that in terms of the corrected curvature general relativity takes the form typical for a gauge field. Finally, we give a geometrical interpretation of the corrected curvature.

This work presents results of property researches of fabricated samples of silica few-mode optical fiber (FMF) with induced chirality under twisting 10 and 66 revolutions per meter, core diameter 11 µm, typical “telecommunication” cladding diameter 125 µm and improved height of quasi-step refractive index profile. Proposed FMF supports 4 guided modes over “C”-band. We represent results of computed characteristics, as well as experimentally measured spectral responses of laser-excited optical signals, including researches and analysis of few-mode effects, occurring after fiber Bragg grating writing.

Background: The role played by the non-dominant parietal lobe in motor cognition, attention and spatial awareness networks has potentiated the use of awake surgery. When this is not feasible, asleep monitoring and mapping techniques should be used to achieve an onco-functional balance. Objective: This study aims to assess the feasibility of a dual-strip method to obtain direct cortical stimulation for continuous real-time cortical monitoring and subcortical mapping of motor and visual pathways simultaneously in parietal lobe tumour surgery. Methods: Single-centre prospective study between May’19-November’20 of patients with intrinsic non-dominant parietal-lobe tumours. Two subdural strips were used to simultaneously map and monitor motor and visual pathways. Results: Fifteen patients were included. With regards to motor function, a large proportion of patients had abnormal interhemispheric resting motor threshold ratio (iRMTr) (71.4%), abnormal Cortical Excitability Score (CES) (85.7%), close distance to the corticospinal tract – Lesion-To-Tract Distance (LTD) – 4.2mm, Cavity-To-Tract Distance (CTD) – 7mm and intraoperative subcortical distance - 6.4mm. Concerning visual function, the LTD and CTD for optic radiations (OR) were 0.5mm and 3.4mm, respectively; the mean intensity for positive subcortical stimulation of OR was 12mA±2.3mA and 5/6 patients with deterioration of VEPs>50% had persistent hemianopia and transgression of ORs. 12 patients remained stable, one patient had a de-novo transitory hemiparesis, and two showed improvements in motor symptoms. A higher iRMTr for lower limbs was related with a worse motor outcome (p=0.013) and a longer CTD to OR was directly related with a better visual outcome (p=0.041). At 2 weeks after hospital discharge, all patients were ambulatory at home and all proceeded to have oncological treatment. Conclusion: We propose motor and visual function boundaries for asleep surgery of intrinsic non-dominant parietal tumours. Pre-operative abnormal cortical excitability of the motor cortex, deterioration of the VEP recordings and CTD<2mm from the OR were related to poorer outcomes.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

This study aimed to use biomineralization technology to improve the bond strength of fiber-reinforced lightweight aggregate concrete (LWAC) after exposure to temperatures of 300 °C and 500 °C. The specimens of a control group (Group A) and two experimental groups (Group B and Group C) were prepared. These specimens healed themselves in different ways after exposure to high temperatures and pull-out tests. The self-healing method of Group A involved placing the specimen into an incubator. The self-healing method of Group B was the same as that of Group A. The self-healing method of Group C involved immersing the specimen in a mixed solution of urea and calcium acetate for two days, then taking it out and placing it in an incubator for two days. A cycle of four days was undertaken until the desired age was reached. After the specimens were healed to the planned age, the first and secondary pull-out tests and repair compound identification were carried out. After exposure to a temperature of 300 °C and self-healing for 90 days, compared with the specimens in Group A, the relative bond strength ratios of the secondary pull-out tests of the specimens in Group C increased by 20.3%. This indicates that biomineralization can effectively improve the bond strength of LWAC after high-temperature damage.

Thermoplastic pultrusion is a suitable process for fabricating continuous unidirectional thermoplastics with a uniform cross-section, high mechanical properties due to continuous fiber reinforcement, low cost, and suitability for mass production. In this paper, jute and glass fibers were reinforced with a polypropylene matrix and fabricated using the thermoplastic pultrusion process. The volumetric fraction of the composite was designed by controlling the filling ratio of the reinforcing fiber and matrix. The effects of molding parameters were investigated, such as pulling speed and molding temperature, on the mechanical properties and microstructure of the final rectangular profile composite. The pulling speed and molding temperature were varied from 40 to 140 mm/min and 190 to 220°C, respectively. The results show that an increase in molding temperature initially led to an increase in mechanical properties, up to a certain point. Beyond that point, they started to decrease. The increase in molding temperature also led to an increase in void content. Meanwhile, un-impregnation decreased with the increase in molding temperature, and the jute fiber began to degrade at high temperatures. In the next step, with varying pulling speed, the mechanical properties decreased as the pulling speed increased, with a corresponding increase in void content and un-impregnation. The decrease in mechanical properties was influenced by the increase in void content and un-impregnation, as the jute fiber degraded at higher temperatures.

During carbonation process, the presence of water is an important parameter to accelerate this phenomenon. The carbon dioxide (CO₂) has been used as curing process production of fiber cement boards keeping the dimensional stability of cellulose fibers in cementitious matrix and promoting the CO₂ capture of environment. In addition, magnesium oxysulfate (MOS) cement has been used as another alternative binder to reduce the amount of CO₂ in the nature. The aim of this scientific paper is analysis the effect of rehydration method on the physical-mechanical properties of CO2-cured magnesium-based fiber cement boards. These boards were produced by Hatschek process simulation. The physical-mechanical performance and microstructural characteristics of MOS boards before and after carbonation were investigated by: water absorption (WA), apparent porosity (AP), and bulk density (BD); four-point bending test; X-ray diffraction (XRD); thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). According to the results, it was possible observe which the accelerated carbonation process resulted in improvements in the mechanical properties of the boards. The boards carbonated after 48 hours showed higher Modulus of Rupture values. The rehydration process of the composites before carbonation led to enhancements in the boards pre-cured for 48 and 72 hours, demonstrating that carbonation occurred more effectively after the supply of water through rehydration. The improvements in mechanical properties were associated with the formation of hydration products, which preferentially formed in the pores and voids of the fiber-cement. The presence of these carbonation products altered the physical properties of the materials, increasing the density of the boards and reducing the void volume. The decomposition of the formed carbonates was confirmed by thermogravimetric analysis, which indicated that the rehydration process favored the carbonation of the materials

This research aimed to determine the effect of alkaline treatment on zalacca midrib fiber (ZMF) concerning various aspects such as thermal stability, crystallinity index, interfacial bonding, interfacial shear strength, water absorption capacity, as well as conducting Scanning Electron Microscopy (SEM). This investigation extended to evaluating the mechanical properties of composites enriched with microcrystalline cellulose with prosthetic socket materials available on the market. Subsequently, ZMF was obtained by splitting and soaking zalacca midrib for 12 hours. Each of ZMF was removed from the midrib and soaked in 5% sodium hydroxide for 3, 6, 9, and 12 hours. The composite material was molded by mixing 10% microcrystalline cellulose with a rotational speed of 150 rpm, maintaining a temperature of 40°C, and continuing the mixing process for 30 minutes. As a result of the alkaline treatment, several positive effects were observed, including increased fiber density, improved particle bonding, increased thermal compatibility, and cleaner fiber surfaces, attributed to reduced levels of hemicellulose, lignin, pectin, and other impurities as confirmed by SEM analysis. The microcrystalline cellulose added to the composite increased the interfacial shear strength, and tensile strength increased by 56.74%, composite flexural strength increased by 76.43%. The SEM analysis results showed that the composite with ZMF on the base fiber broke during the tensile test because fiber experienced an increase in interfacial bonding between fiber and the matrix. The water absorption test showed that untreated fiber had a higher level of absorption

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

The study presents the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO2) nanoparticles using the phase inversion technique. The newly developed membranes were systematically characterized using advanced tools and methods to evaluate their properties and performance. The study focused on investigating the effects of TiO2 addition in the SPPSu inner layer on pure water permeability, and salt rejection. The nanocomposite hollow fiber nanofiltration membranes exhibited a significant enhancement in pure water permeability, with a three-fold increase compared to the pristine membranes, achieving a flux of 5.4 L/m2h.bar. The addition of TiO2 also led to an improvement in the mechanical properties of the membranes, as evidenced by the increase in the expected tensile strength from 2.4 to 3.9 MPa. To evaluate the salt rejection performance, rejection tests were conducted using a laboratory-scale filtration setup in recycle mode. Aqueous solutions containing different divalent ions, specifically magnesium sulfate (Mg2SO4) and sodium sulfate (Na2SO4) at a concentration of 500 ppm, were used as the feed solution. The modified dual-layer hollow fiber nanocomposite membranes exhibited a maximal rejection of 95% for Mg2SO4, demonstrating their effective separation capabilities for divalent ions. The findings of this study highlight the successful synthesis and characterization of dual-layer SPPSu nanocomposite hollow fiber nanofiltration membranes incorporating TiO2 nanoparticles. The incorporation of TiO2 resulted in improved pure water flux, mechanical strength, and salt rejection performance. These enhanced properties make the developed nanocomposite membranes promising candidates for applications in nanofiltration processes, particularly for the selective separation of divalent ions from aqueous solutions.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

The gut microbiota plays a crucial role in childhood obesity, and diet is a dominating driver. The effects of fructo-oligosaccharides (FOS), as a dietary fiber, on the composition and metabolism of gut microbiota in healthy children was investigated by vitro fermentation system with a reformative YCFA medium (rich in tryptic hydrolysates of meat). The 16S rRNA sequencing technology was utilized to analyze the varieties of gut microbiota. Measurement of short chain fatty acids (SCFAs) and gases were used by the gas chromatograph. Majorbio Cloud Platform and MetOrigin, as the interactive cloud server, perform the microbiota analysis, the metabolic pathway enrichment analysis, the statistical correlations, and biological relationships using network visualization. We found that the FOS group significantly regulated the composition and metabolism of gut microbiota. The co-metabolism network showed that 3 metabolites were related to 6 differential bacteria and 8 metabolism pathways. These findings suggest that dietary fiber could regulate the composition of gut microbiota and its metabolites in a better direction, but when dietary fiber participates in precision nutrition formula, it may be relevant for precision obesity, may help identify windows of opportunity for the dietary intervention of childhood obesity.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

The experimental verification for the computational method sometimes varies due to numerous factors such as the manufacturing process and the materials' property change due to environmental aspects. In this work, we performed verification of experimental and computational evaluation of a hybrid composite moderate thick plate. The experiment was performed with simplistic approaches and without the advanced tools of preparing composite materials. This is due to the fact that most of the students in many developing countries around the world cannot have access to such equipment. As such, in this research, we are presenting cheap and easy preparation methods, with some details, for even equipment calibration and some tricks to attain a reliable composite structure for educational purposes. Moreover, the software and solvers used in this study are freely provided by the supplier for educational purposes. This study examined two methods for producing carbon and glass/polyester composite plates and discussed which one was best based on mechanical properties for different volume fractions, random stacking sequences, and ply angles (using OCTAVE's random estimation program). It also determined the three natural frequencies experimentally and with the aid of ANSYS. Less than 6% separated the experimentally determined natural frequencies from the calculated results.

Guided ultrasonic waves are suitable for use in the context of structural health monitoring of thin-walled, plate-like structures. Hence, observing the wave propagation in the plates can provide an indication of whether damage has occurred in the structure. In this work, the wave propagation in fiber metal laminate consisting of thin steel foils and layers of carbon fiber-reinforced polymer is studied, focusing on the main propagation characteristics like dispersion diagrams and displacement fields. For this purpose, the dispersion diagrams derived from the analytical framework and numerical simulations are first determined and compared to each other. Next, the displacement fields are computed using the global matrix method for two excitation frequencies. The results derived from the analytical framework is used to validate numerically determined displacement fields based on a 2D and a 3D modeling approach. For both investigations the results of the analytical treatment and the numerical simulation show good agreement. Furthermore, the displacement field reveals the typical and well-known characteristics of the propagation of guided waves in thin-walled structures. Since the use of full 3D models involves a very high computational cost, this work also successfully investigates the possibility for model order reduction to decrease the computational time and costs of the simulation without the loss of accuracy.

In this study, the influence of graphene oxide nanoparticles on the bond-slip behavior of fiber and fly ash based geopolymer paste was examined. Geopolymer paste incorporating graphene oxide nanoparticles solution was cast in half briquetted specimens and embedded with a fiber. Three types of fibers were used: steel, polypropylene, and basalt. The pullout test was performed at two distinct speeds: 1 mm/second and 3 mm/second. Results showed that the addition of graphene oxide increased the compressive strength of geopolymer by about 7%. The bond-slip responses of fibers embedded in geopolymer mixed with graphene oxide exhibited higher peak stress and toughness as compared to those embedded in normal geopolymer. Each fiber type also showed different mode of failure. Both steel and polypropylene fibers showed full bond-slip responses due to their high ductility. Basalt fiber, on the other hand, because of its brittleness, failed by fiber fracture mode which showed no-slip in pull out responses. Both bond strength and toughness were found to be rate sensitive. The sensitivity was higher in graphene oxide/geopolymer than in conventional geopolymer.

With the ever-increasing rate, obesity has become an epidemiological problem throughout the globe comprising about 39% of the world population as of now. Among several reasons, disruption of the gut microbial ecosystem might contribute to the pathogenesis of metabolic disorders, including obesity, metabolic syndrome, type 2 diabetes, and other associated comorbidities. Though the mechanisms related to dysbiosis are unclear, diet might play a modulating role where different dietary approaches manipulate microbial richness and abundance as well as stability. For instance, shifting of Firmicutes and Bacteroidetes ratio in the gut might have a role in association with the dietary approaches and ingestion duration. Along with altered gut microbial composition, microbial metabolites such as short-chain fatty acids (SCFA) after ingestion of non-digestible dietary starches may have an impact on host metabolism by regulating lipogenesis, gluconeogenesis, and inflammation with potential associations to health and obesity. The dietary approaches like carbohydrates, fibre, protein, and/or fat diet at various arrangements can make a shift in the composition of gut microbiota if introduced for a short period. However, the unique pattern of the gut microbes usually remains the same along with the longer period of habitual diet. Though the short-term dietary intervention or circadian rhythm influences a transient change in gut microbes, other than habitual diet, the understanding related to long-term dietary change-induced permanent alterations is minimum. Alternatively, the usage of prebiotics, probiotics as well as postbiotics could be beneficial to overcome dysbiosis. This review highlights the current knowledge and the interaction between the human intestinal microbiota and diet as a modifying factor, in obesity allowing the scientists to uncover novel targets and tools to use as customized therapy.

The aim of the study was to assess the effect of the addition of inulin and the replacement of part of inulin with apple fiber on the physicochemical and organoleptic properties. Moreover, the survival of Bifidobacterium animalis ssp. Lactis Bb-12 and Lactobacillus rhamnosus was studied in sheep milk ice cream. There was no effect of apple fiber and the type of bacteria on the number of bacteria of the probiotics after fermentation. As a result of freezing, mixture containing Bifidobacterium animalis ssp. Lactis Bb-12, there was a significant reduction in the bacterial from 0.39 log cfu g −1 to 0.46 log cfu g −1. In all ice cream on the 21st day of storage, it exceeded 10 log cfu g –1, which means that the ice cream retained the status of probiotic products. The Lactobacillus rhamnosus ice cream showed a lower yellow colour compared to the Bifidobacterium Bb-12 ice cream. The overrun of sheep's milk ice cream was within a range from 78.50% to 80.41%. The appearance of sheep's milk ice cream is influenced considerably by the addition of fiber and the type of bacteria and the interaction between the type of bacteria and the addition of fiber and storage time and fiber.

We report world record high data transmission over standard optical fiber from a single optical source. We achieve a line rate of 44.2 Terabits per second (Tb/s) employing only the C-band at 1550nm, resulting in a spectral efficiency of 10.4 bits/s/Hz. We use a new and powerful class of micro-comb called soliton crystals that exhibit robust operation and stable generation as well as a high intrinsic efficiency that, together with an extremely low spacing of 48.9 GHz enables a very high coherent data modulation format of 64 QAM. We achieve error free transmission across 75 km of standard optical fiber in the lab and over a field trial with a metropolitan optical fiber network. This work demonstrates the ability of optical micro-combs to exceed other approaches in performance for the most demanding practical optical communications applications.

Azo dyes are the most widely used synthetic dyes in the printing and dyeing process. However, the discharge of untreated azo dyes poses potential threat for human health and aqueous ecosystem. Herein, we fabricated a novel heterogenous catalyst - activated carbon fiber-supported ferric alginate (FeAlg-ACF) . Together with peroxymonosulfate (PMS) and visible light, this photocatalytic oxidation system was used to remove an azo dye - azophloxine. The results indicated that the proposed catalytic oxidation system can remove 100% azophloxine within 24 min, while under the same system, the removal rate was only 92 % and 84 % when ferric alginate was replaced with ferric citrate and ferric oxalate respectively, which showed the superiority of activated carbon fiber-supported ferric alginate. The degradation of azophloxine is achieved by the active radicals (SO4•− and •OH) released from PMS and persistent free radicals from activated carbon fiber. After treating for 24 min, the total organic carbon of azophloxine solution (50 μmol/L) decreased from 1.82 mg/L to 79.3 μg/L and the nitrate concentration of ions increased from 0.3 mg/L to 8.6 mg/L. That is, up to 93.5% azophloxine molecules were completely degraded into inorganic compounds. Consequently, potential secondary contamination by intermediate organic products during catalytic degradation was prohibited. The azophloxine removal ratio was kept almost constant after seven cycles, indicating the recyclability and longevity of this system. Furthermore, the azophloxine removal was still promising at high concentrations of Cl-, HCO3-, CO32-. Therefore, our proposed system is potentially effective to remove dye pollutants from seawater. It provides a feasible method for the development of efficient and environmental friendly PMS activation technology combined with FeAlg-ACF, has significant academic and application value.

We experimentally demonstrate, for the first time, blind nonlinearity compensation using the Density-Based Spatial-Clustering of Applications with Noise (DBSCAN) algorithm for a 40-Gb/s 16-quadrature amplitude modulated being transmitted at 50 km of standard single-mode fiber. At high launched optical powers, DBSCAN offers up to 0.83- and 8.84-dB enhancement in Q-factor when compared to conventional K-means clustering and linear equalization, respectively.

Nutrition is crucial for the management of patients affected by chronic kidney disease (CKD) to slow down disease progression and to correct symptoms. The mainstay of the nutritional approach to renal patients is protein restriction coupled with adequate energy supply to prevent malnutrition. However, other aspects of renal diets, including fiber content, can be beneficial. This paper summarizes the latest literature on the role of different types of dietary fiber in CKD, with special attention to intestinal microbiota and the potential protective role of renal diets. Fibers have been identified based on aqueous solubility, but other features, such as viscosity, fermentability, and bulking effect in the colon should be considered. A proper amount of fiber should be recommended not only in the general population but also in CKD patients, to achieve an adequate composition and metabolism of intestinal microbiota and to reduce the risks connected with obesity, diabetes, and dyslipidemia.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

In this paper, we investigate an animal-human cohabitation problem with the help of machine learning and fiber-wireless (FiWi) access networks integrating cloud and edge (fog) computing. We propose an early warning system which detects wild animals nearby road/rail with the help of wireless sensor networks and alerts passing vehicles of possible animal crossing. Additionally, we show that animals' detection at the earliest and the related processing, if possible, at sensors would reduce the energy consumption of edge devices and the end-to-end delay in notifying vehicles, as compared to the scenarios where raw sensed data needs to be transferred up the base stations or the cloud. At the same time, machine learning helps in classification of captured images at edge devices, and in predicting different time-varying traffic profiles-- distinguished by latency and bandwidth requirements-- at base stations, including animal appearance events at sensors, and allocating bandwidth in FiWi access networks accordingly. We compare three scenarios of processing data at sensor nodes, base stations and a hybrid case of processing sensed data at either sensors or at base stations, and showed that dynamic allocation of bandwidth in FiWi access networks and processing data at its origin leads to lowering the congestion of network traffic at base stations and reducing the average end-to-end delay.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

Background We aimed to compare the retinal, optic disc vascular density (ODVD) values, and acircularity index (AI) of patients with idiopathic macular telangiectasia type 2 (IMT) and healthy individuals using the optical coherence tomography angiography(OCTA) device. Methods The study included 39 patients with IMT and 37 healthy controls. The OCTA findings of the patients and controls were examined. Results The total, parafoveal and perifoveal vascular density of the superficial capillary plexus, choriocapillaris blood flow, inside-disc ODVD, retinal nerve fiber layer (RNFL), and retinal thicknesses were found to be statistically significantly lower and the foveal avascular zone value was statistically significantly higher in the IMT group compared to the control group (p=0.001, p=0.01, p=0.02, p=0.01, p=0.009, p=0.002, p=0.02, respectively).There was a statistically significant negative correlation between best-corrected visual acuity (BCVA) and AI (p=0.02), a statistically significant positive correlation between peripapillary vascular density and BCVA(p=0.04). Conclusion We consider that the lower retinal, choriocapillaris, and ODVD values, retinal and RNFL thicknesses in the patients with IMT compared to the controls were due to vascular damage, remodeling, fibrosis, proliferation, and Müller cell damage. Ellipsoid zone defect, AI, and peripapillary vascular density are important indicators in the evaluation of visual acuity in these patients.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.