Chromium-nickel austenitic stainless steels are widely used due to their high corrosion resistance, good weldability and deformability. To some extent, their application is limited by their mechanical characteristics. As a result of their austenitic structure, increasing the static and dynamic strength of the components can be achieved by surface cold work. Due to the tendency of these steels to undergo intercrystalline corrosion, another approach to improve their mechanical characteristics is the use of low-temperature thermo-chemical diffusion processes. This article proposes a new combined process based on sequentially applied diamond burnishing (DB) and low-temperature gas nitriding (LTGN) to optimally improve the fatigue strength of 304 steel. The essence of the proposed approach is to combine the advantages of the two processes (DB and LTGN) to create a zone of residual compressive stresses in the surface and subsurface layers–the enormous surface residual stresses (axial and hoop) introduced by LTGN, with the significant depth of the compressive zone characteristic of static surface cold working processes. DB (both smoothing and single-pass hardening), in combination with LTGN, achieves a fatigue limit of 600 MPa, an improvement of 36.4% compared to untreated specimens. Individually, smoothing DB, single-pass DB and LTGN achieve 540 MPa, 580 MPa and 580 MPa, respectively. It was found that as the degree of plastic deformation of the surface layer introduced by DB increases, the content of the S-phase in the nitrogen-rich layer formed by LTGN decreases, with resultant increased content of -phase, and a new (also hard) phase: stabilized nitrogen-bearing martensite.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

Removal of hexavalent chromium had attracted much more attention as it was a hazardous contaminant. Electrochemical reduction technology was applied to removal chromium (VI) from wastewater. The mechanism and parameters affect the reduction process were investigated. The results showed that the reduction efficiency was significantly affected by the concentration of H2SO4, current density and reaction temperature. And the reduction efficiency was up to 86.45% at concentration of H2SO4 of 100g/L, reaction temperature of 70 ℃, current density at 50 A/m2, reaction time at 180 min and stirring rate of 500 rpm. The reduction process of chromium (VI) was followed pseudo-first-order equation, and the reduction rate could be expressed as Kobs = k [H2SO4]1• [j] 4•exp-4170/RT.

The direct Cr (VI) reduction process by oxalic acid was conducted and the results showed that the Cr (VI) was efficiently reduced by oxalic acid at high reaction temperature and high dosage of oxalic acid. The reduced product, Cr (III), was easily generated stable complex compounds (Cr(HC2O4)3) with oxalate, which displayed a negative effect on the reduction process. The high reaction temperature and high acidic medium could destroy the stable structure of a complex compound to release oxalate, and facilitate the reduction of Cr (VI). Generally, the present study provided a versatile strategy for Cr (VI) reduction, exhibiting a bright application future for real wastewater treatment.

A field sampling event was conducted to measure the concentrations of metals within the trunks of felled trees on a college campus east of New York City. Heavy metals, particularly chromium, were found present in the soils surrounding the sampled trees, allowing for a correlation coefficient to be calculated with soil and tree concentrations. A statistically significant Pearson correlation was found between these two concentrations among the samples. This study is aimed at providing researchers a starting point for their research a better understanding of local ecologies, prediction of future change, and dissemination of conservation efforts.

The present investigation deals with the adsorption of chromium(III) from alkaline media using multi-walled carbon nanotubes. The adsorption of Cr(III) has been studied under various experimental conditions: stirring speed of the aqueous solution, initial metal and adsorbent concentrations, NaOH concentration in the aqueous solution, and temperature. The rate law indicated that chromium adsorption is well represented by the particle diffusion model, whereas the adsorption process fits to the pseudo-second order kinetic model within an exothermic character. Equilibrium data fit to the Langmuir type-2 equilibrium isotherm in an spontaneous process. Chromium(III) can be eluted from metal-loaded nanotubes using acidic solutions, from which fine chromium(III) oxide pigment can be ultimately yielded.

This research work studies the characteristics of wear and wear resistance of composite powder coatings, deposited by high-velocity oxygen fuel, which contain composite mixtures Ni-Cr-B-Si having different chromium concentrations – 9.9%; 13.2%; 14%; 16% and 20% , at one and the same size of the particles and the same content of the remaining elements. The coating of 20% Cr does not contain B and Si. Out of each powder, composite coatings have been prepared without any preliminary thermal treatment of the substrate and with preliminary thermal treatment of the substrate up to 650оС. The coatings have been tested under identical conditions of dry friction over a surface of solid firmly attached abrasive particles using the tribological testing device „Pin-on-disk“. Results have been obtained and the dependences of the hardness, mass wear, intensity of the wearing process, absolute and relative wear resistance on the Cr concentration under identical conditions of friction. It has been found out that for all the coatings the preliminary thermal treatment of the substrate leads to a decrease in the wear intensity. Upon increasing Cr concentration the wear intensity diminishes and it reaches minimal values at 16% Cr. In the case of coatings having 20% Cr concentration, the wear intensity is increased, which is due to the absence of the components B and Si in the composite mixture, whereupon no inter-metallic structures are formed having high hardness and wear resistance. The obtained results have no analogues in the current literature and they have not been published by the authors.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Nickel-based ethylene polymerization catalysts have unique features, being able to produce macromolecules with a variable content of branches, resulting in polymers ranging from semicrystalline plastics to elastomers to hyperbranched amorphous waxes and oils. In addition to Brookhart's α-diimine catalysts, iminopyridine Ni(II) complexes are among the most investigated systems. We report that Ni(II) complexes bearing aryliminopyridine ligands with bulky substituents both at the imino moiety and in the 6-position of pyridine afford either hyperbranched low molecular weight polyethylene oils or prevailingly linear crystalline polyethylenes or both depending on the ligand structure and the reaction conditions. The formation of multiple active species in situ is suggested by analysis of the post-polymerization catalyst residues, showing the partial reduction of the imino function. Some related arylaminopyridine Ni(II) complexes were also synthesized and tested, showing a peculiar behavior, i.e. the number of branches of the produced polyethylenes increases while ethylene pressure increases.

The effect of dentin pretreatment with desensitizing paste containing 8% arginine and calcium carbonate on the retention of laser-sintered cobalt-chromium (Co-Cr)-based crowns was examined. Forty molars were prepared using a standardized protocol. The Co-Cr crowns were produced using selective laser melting. The teeth were either pretreated with the desensitizing paste or not pretreated. After one week, each group was cemented with glass ionomer cement (GIC) or zinc phosphate cement (ZPC). Surface areas of the teeth were measured before cementation. After aging, the cemented crown-tooth assemblies were tested for retentive strength using a universal testing machine. The debonded surfaces of the teeth and crowns were examined at 2.7× magnification. Pretreating the dentin surfaces with the desensitizing paste before cementation with GIC or ZPC did not affect the retention of the Co-Cr crowns. The retention of the GIC group (6.04±1.10 MPa) was significantly higher than that of the ZPC group (2.75±1.25 MPa). The predominant failure mode for the ZPC and for the nontreated group of the GIC was adhesive cement-dentin; for the GIC-treated group, it was adhesive cement-crown. The desensitizing paste can be safely used to reduce postcementation sensitivity without reducing the retentive strength of Co-Cr crowns cemented with GIC or ZPC.

In the present work, effect of basic components on the energy pathway of ethylene oligomerization by landmark Chevron-Phillips catalyst has been explored in detail using density functional theory (DFT). Studied factors were chosen considering the main components of Chevron-Phillips catalyst, i.e. ligand, cocatalyst and halocarbon compounds, comprising i) the type of alkyl substituents in pyrrole ligand as methyl, iso-propyl, tert-butyl, and phenyl, as well as the simple hydrogen, and the electronwithdrawing fluoro and trifluoromethyl; ii) the number of Cl atoms in Al-compound (as AlMe2Cl, AlMeCl2 and AlCl3) which indicates halocarbon amount and iii) cocatalyst type as alkylboron, alkylaluminium, or alkylgallium. Besides main ingredients, solvent effect, from toluene or methylcyclohexane, on oligomerization pathway was explored as well. In this regard, the full catalytic cycles for the main product (1-hexene) formation as well as side reactions, i.e. 1-butene release and chromacyclononane formation, were calculated on the basis of the metallacycle based mechanism. Based on results, a modification on the Chevron-Phillips catalyst system, to reach higher 1-hexene selectivity and activity, is suggested.

Metallic masters can be used as a metallic mold to replicate polymeric pieces with high resolution. Metallic masters with high resolution were created by photolithography technique and nickel electrodeposition technique. AZ 9260 photoresists and SPR 220-7.0 photoresists were used to coat metallic substrates and to compare results. Steel substrate and nickel substrate were used as the metallic substrate to compare results. Two different nickel electrodeposition protocols were used to compare results. In the conclusion section, was determined the best photoresist, metallic substrate, and nickel electrodeposition protocol to fabricate metallic masters.

In this scientific research, thermally stable nickel nanoparticles were synthesized and characterized. Nickel nanoparticles were synthesized using phenol –formaldehyde by chemical method followed by calcination. The polymer metal complex was confirmed by FTIR and NMR. The spherical morphology of nickel nanoparticles confirmed by SEM. The crystallographic structure is confirmed by XRD and size of cobalt nanoparticles is 24.0 nm. The TGA analysis was performed over a range of 29-600OC. The TGA thermograph predicts mass decomposition of 11%, for nickel phenol-formaldehyde nanocomposite. The decomposition rate of composites is very low 2% weight loss per 100OC increment in temperature.

Iron-containing nickel sulfides, selenides, and sulfoselenides were synthesized via a simple two-step hydrothermal reaction (temperature 160 °C) for their application as electrocatalysts in the oxygen evolution reaction (OER) in an alkaline solution (1 mol L–1 KOH). The study demonstrated that iron-containing nickel cobalt sulfides and selenides exhibit superior OER performance with lower overpotentials compared to iron-free nickel cobalt sulfide and selenide, which highlights the significant role of iron in enhancing OER nickel cobalt electrocatalysts: Fe0.1Ni1.4Co2.9(S0.87O0.13)4, η50 = 318 mV; Fe0.2Ni1.5Co2.8(S0.9O0.1)4, η50 = 310 mV; Fe0.3Ni1.2Co2.5(S0.9O0.1)4, η50 = 294 mV; Fe0.6Ni1.2Co2.5(S0.83O0.17)4, η50 = 294 mV, Fe0.4Ni0.7Co1.6(Se0.81O0.19)4, η50 = 306 mV compared to Ni1.0Co2.1(S0.9O0.1)4, η50 = 346 mV and Ni0.7Co1.4(Se0.85O0.15)4, η50 = 355 mV (all values at current densities η50 of 50 mA cm–2). Furthermore, the iron-containing nickel cobalt sulfoselenide Fe0.5Ni1.0Co2.0(S0.57Se0.25O0.18)4 displayed exceptional OER performance with η50 = 277 mV, surpassing the benchmark RuO2 electrode with η50 = 299 mV. The superior performance of the sulfoselenide was attributed to its low charge transfer resistance (Rct) of 0.8 Ω at 1.5 V vs. the reversible hydrogen electrode (RHE). Moreover, the sulfoselenide demonstrated remarkable stability, with only a minimal increase in overpotential (η50) from 277 mV to 279 mV after a 20 h chronopotentiometry test. These findings suggest that trimetallic iron, nickel and cobalt sulfide, selenide and especially sulfoselenide materials hold promise as high-performance, cost-effective, and durable electrocatalysts for sustainable OER reactions. This study provides a valuable approach for the development of efficient electrocatalytic materials, contributing to the advancement of renewable energy technologies.

The effects of exogenous inorganic [i.e., nitrate (NO3-)/ammonium (NH4+)] and organic [i.e., glutamate (Glu)/argine (Arg)] N alone and in combination on the accumulation of proline (Pro) in rice plant under trivalent chromium [Cr(III)] stress were studied through the mass balance matrix model (MBMM). ‘NH4+’ application showed the largest contribution to the Pro content in rice shoots under different concentrations of Cr(III), followed by ‘NO3-’, ‘Arg’, and ‘Glu’ application respectively. While, ‘Arg’ application displayed the largest contribution to the Pro content in roots under Cr(III) stress, followed by ‘NH4+’, ‘Glu’, and ‘NO3-’ application. Among the combination cases of N sources used, the application of ‘NH4++Arg’ showed the greatest contribution to the Pro content in both roots and shoots of Cr(III)-treated rice seedlings, while the application of ‘NO3-+Glu’ showed the least contribution to the Pro content in rice seedlings under Cr(III) stress. Results from this study indicated that the level of indigenous Pro in rice seedlings is quite sensitive to Cr(III) stress under different N sources, and mathematical modeling showed a reliable result to estimate the relationship between Pro content and N source application in rice plants in response to Cr(III) exposure .

Cohesion in the refractory metals Cr, Mo, and W is phenomenologically described in this work via a n-body energy functional with a set of physically motivated parameters that were optimized to reproduce selected experimental properties characteristic of perfect and defective crystals. The functional contains four terms accounting for the hard-core repulsion, the Thomas-Fermi kinetic energy repulsion and for contributions to the binding energy of s and d valence electrons. Lattice dynamics, molecular statics, and molecular dynamics calculations show that this model describes satisfactorily thermodynamic properties of the studied metals whereas, unlike other empirical approaches from the literature, predictions of phonon dispersion relations and of surface and point defect energetics reveal in fair good agreement with experiments. These results suggest that the present model is well adapted to large-scale simulations and whenever total energy calculations of thermodynamic properties are unfeasible

Abstract The global concern about the leather industries is increasing as the leather industries grow bigger each year. These industries face a very challenging task with an increase in stringent pollution control regulation enforced by various bodies due to environmental concern and human risks. The chromium salts are the most widely used chemical for the tanning process in leather industries, about 35% of chromium used for the tanning process remain as metal and discharge to wastewater stream. The removal and recovery of this quantity of wasted chromium are necessary for environmental pollution control and economic reason. This paper sheds light on the chromium recovery and reuse system of Chromium salts in tanning wastewater by using NaOH as an effective chemical precipitation method to regenerate chromium solution, adapted chrome recovery plant, and evaluated the system technically and economically.

Background: Gingival enlargement is defined as an abnormal overgrowth of gingival tissues. A case of a 34–year–old female presenting with maxillary chronic inflammatory gingival enlargement associated with a nickel wire allergy is reported here. Replacement of the wire, good oral hygiene therapy and surgical therapy was carried out to provide a good aesthetic outcome. Histopathological evaluation was done of the excised specimen. There is only one similar case reported in literature to the best of our knowledge and ours is the second case. Result: A Histopathological diagnosis of inflammatory fibrous hyperplasia was established. No recurrence was reported at the end of 1 year. Conclusion: The patient should be made aware of the allergy at the initial visit and oral hygiene instructions should be reinforced at every visit. The significance of patient compliance during and following therapy as an important factor in the success of treatment.

Anion exchange membrane (AEM) electrolysis is hampered by two main issues: stability and performance. Focusing on the latter, this work demonstrates a highly active NiMo cathode for hydrogen evolution in AEM electrolysis. We demonstrate an electrolyzer performance of 1 A cm⁻² at 1.9 V (total cell voltage) with a NiMo loading of 5 mg cm⁻² and an iridium black anode in 1 M KOH at 50 °C, that may be compared to 1.8 V for a similar cell with Pt at the cathode. The catalysts developed here will be significant in supporting the pursuit of cheap and environmentally friendly hydrogen fuel.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Valence tautomerism (VT) may occur if a molecule contains two chemically different redox-active units, which differ only slightly in their intrinsic redox potential. Herein, we present three new half-sandwich complexes [(η6arene)Cr(CO)2L]+ with a triarylmethylium substituent appended to the -coordinated arene and different coligands L (L = CO, P(OPh)3, PPh3, 1+  3+) at the chromium atom. Ligand substitution purposefully lowers the half-wave potential for chromium oxidation and thereby the redox potential difference towards tritylium reduction. For the PPh3-substituted complex 3+, cyclic voltammetry measurements indicate that chromium oxidation and tritylium reduction occur at (almost) the same potential. This renders the diamagnetic Cr(0)C6H4CAr2+ form 3+ and its paramagnetic diradical Cr(I)+•C6H4CAr2• valence tautomer 3+•• energetically nearly degenerate. Temperature-dependent IR spectroscopy shows indeed two pairs of carbonyl bands assignable to a Cr(0) and a Cr(I) species, coexisting in a T-dependent equilibrium with almost equal quantities for both at 70 °C. The diradical form with one unpaired spin at the trityl unit engages in a monomer ⇌ dimer equilibrium, which was investigated by means of quantitative EPR spectroscopy. The diradical species 1+••  3+•• were found to be highly reactive, leading to several identified reaction products, which presumably result from hydrogen atom abstraction by the trityl C atom, e.g. from the solvent.

A partial least squares (PLS) quantitative chemometric method based on the analysis of the MID-FTIR spectrum of polymer inclusion membranes (PIMs) used for the extraction of Cr(VI) from aqueous media is developed. The system previously optimized considering the variables membrane composition, extraction time, and pH, is characterized in terms of its adsorption isotherm, distribution coefficient, extraction percent and enrichment factor. A Langmuir type adsorption behavior with KL = 21.99 L/mg, qmax = 0.242 mmol/g and 0<RL<1, indicates that metal adsorption is favorable. The characterization of the extraction reaction is performed as well showing an 1:1 Cr(VI):Aliquat 336 ratio, in agreement with solvent extraction data. The principal component analysis (PCA) of the PIMs revels a complex pattern, which is satisfactorily simplified and related to Cr(VI) concentrations through the use of a variable selection method (iPLS) in which bands in the ranges 3451–3500 cm-1 and 3751–3800 cm-1 are chosen. The final PLS model including the 100 wavelengths selected by iPLS and 10 latent variables shows excellent parameter values with RMSEC: 3.73115, RMSECV: 6.82685, Bias: -1.91847e-13, CV Bias: 0.185947, R2 Cal: 0.98145, R2 CV: 0.940902, recovery%: 104.02 ± 4.12 (=0.05), sensitivity%: 0.001547 ppb, γ: 3.8 ppb, γ- 1: 0.6 ppb-1, selectivity: 0.0155, linear range: 5.8–100 ppb, LD: 1.9 ppb, and LQ: 5.8 ppb. The developed PIM sensor is easy to implement as it requires few manipulations and reduced number of chemical compounds in comparison to other similar reported systems.

The hydrogen evolution reaction (HER) has garnered attention to access sustainable energy generation with a pollutant-free combustion product in the form of H2 gas. Despite the utility of this pathway in the context of growing climate concerns, stable HER electrocatalysts which avoid the use of rare-earth platinum while retaining high catalytic performance and efficiency remains a challenge. In this work, we present the application of a binuclear nickel (II/III) Schiff base complex [Ni]2[L]2 2 for HER electrocatalysis. The design of the electrocatalyst provides optimal HER activity as the presence of electronegative heteroatoms in proximity to the metal centers augments proton affinity. As a result, the catalyst displays excellent HER activity with 100% faradaic efficiency (FE) at an onset potential of 0.4 V vs. reverse hydrogen electrode (RHE), sustained catalytic activity during prolonged electrolysis for greater than 17 hours, and provided a turn over number (TON) of 0.0006 s-1.

Urea, a prevalent component found in wastewater, shows great promise as an alternative substrate to water for energy-efficient hydrogen production by electrolysis. However, the sluggish kinetics of the anodic urea oxidation reaction (UOR) significantly hampers the overall reaction rate. To address this challenge, this article presents a comprehensive study focusing on the controlled fabrication of hierarchically structured nanomaterials as potential catalysts for UOR. The prepared MnO2@NiCo-LDH hybrid catalyst demonstrates remarkable improvements in reaction kinetics, benefiting from synergistic enhancements in charge transfer and efficient mass transport facilitated by its unique three-dimensional architecture. Notably, the catalyst exhibits an exceptionally low onset potential of 1.228 V and requires only 1.326 V to achieve an impressive current density of 100 mA cm-2, representing a state-of-the-art performance in UOR. These findings highlight the tremendous potential of this innovative material-designing strategy to drive advancements in electrocatalytic processes.

Abstract: Five patients with standard medical treatment-resistant symptoms of skin lesions, ear infections, allergic rhinitis, nasal congestion, asthma, heartburn, and failure to thrive were success- fully treated with an integrative medicine assessment and integrative medicine treatment approach. The integrative medicine assessment method of autonomic response testing enabled the identifica- tion of nickel sensitivity as a common element in these patients. It guided the use of the integrative medicine therapies of low dose immunotherapy, gamma linoleic acid supplementation, chelation, dietary nickel restriction, and removal of nickel containing dental and cosmetic appliances. A chart review of 151 patients indicated a strong association of nickel and the simultaneous presence of skin lesions.

Magnetoelectric sensors based on microelectromechanical cantilevers consisting of TiN / AlN / Ni are investigated using finite element simulations in regard of the anisotropy of the E effect and its impact on the sensor sensitivity. The E effect is derived from the anisotropic magnetostriction and magnetization of single crystalline Nickel. The magnetic hardening of Nickel in saturation is demonstrated for the (110) as well as the (111) orientation. It is shown further, that magnetostrictive bending of the cantilever has a negligible impact on the eigenfrequency and thus sensitivity. The intrinsic E effect of Nickel decreases in magnitude depending on the crystal orientation when integrated into the magnetoelectric sensor design. The transitions of the individual magnetic domain states are found to be the dominant influencing factor on the sensitivity for all crystal orientations. The peak sensitivity was determined to 41.3 T-1 for (110) in-plane orientated Nickel at a magnetic bias flux of 1.78 mT. It is found, that the transition from domain wall shift to domain rotation along the hard axes yields much higher sensitivity than the transition from domain rotation to magnetization reversal. The results achieved in this work show that Nickel as hard magnetic material is able to reach almost identical sensitivities as soft magnetic materials, such as FeCoSiB.

While there are extensive studies on the mineralogy and geochemistry of laterites worldwide, the temporal and spatial mineralogical development of a typical nickel laterite profile is still poorly constrained. In this study, we present a detailed mineralogical and geochemical characterization of samples systematically collected from a nickel laterite profile at the Sta. Cruz nickel laterite deposit, Zambales, Philippines, to describe the temporal and spatial development of the laterite profile. Wavelength-dispersive X-ray fluorescence spectroscopy (WDSXRF), mass balance-element mobility calculations, transmitted and reflected light microscopy, and previously reported results from coupled X-ray diffraction (XRD) and Rietveld refinement analyses, reveal that the laterite profile investigated is composed of two main horizons: the limonite and saprolite zones, separated by a thin transitional zone. The main zones are further subdivided into subzones based primarily on the mineral assemblage and major element chemistry: upper limonite, lower limonite, transitional zone, upper saprolite, and lower saprolite. Late-stage Ni-rich serpentine veins were observed cutting the upper and lower saprolite subzones. Investigation of the structure of goethite within the limonite zone via Rietveld refinement show that the crystallinity of goethite decreases with increasing Ni content and increasing crystallite size. This suggests that upwards through the limonite zone, as goethite ages, its crystallinity increases which possibly results in the removal of Ni from its crystal structure and eventual remobilization to the lower laterite zones. We propose a genetic model of the formation of the Sta. Cruz laterite consisting of four stages: (1) early-stage alteration, (2) continued serpentinization and volume expansion, (3) late stage serpentinization, dissolution, and incipient oxide formation, and (4) goethite ageing and Ni-rich serpentine vein formation. Overall, our results suggest that serpentinization is an important aspect of Ni laterite formation, both before and after the emplacement of the peridotite protolith.

In aqueous solution planar bis(1,2-dithiooxalato)nickelates(II), [Ni(dto)2]2- react with lanthanide ions (Ln3+) to form pentanuclear, hetero-bimetallic complexes of the general composition [{Ln(H2O)n}2{Ni(dto)2}3] · x H2O (n = 4 or 5; x = 9 - 12). Two complexes of this series, [{Pr(H2O)5}2{Ni(dto)2}3] · 11 H2O, Pr2Ni3 1 and [{Gd(H2O)5}2{Ni(dto)2}3] · 11 H2O, Gd2Ni3 2 were synthesized and characterized by single crystal X-ray structure analysis, X-ray powder diffraction, and IR spectroscopy. All Ln2Ni3 complexes crystallize as monoclinic crystals in the space group P21/c.

Nickel molybdate, NiMoO₄, nanoparticles were synthesized via calcination of an oxalate complex in static air at 500 °C. The oxalate complex was analyzed by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). The as-synthesized nickel molybdate was characterized by Brunauer–Emmett–Teller technique (BET), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and its catalytic efficiency was tested in the reduction reaction of the three-nitrophenol isomers. The nickel molybdate displays a very high activity in the catalytic reduction of the nitro functional group to an amino. The reduction progress was controlled using UV-Vis absorption.

A conventionally cast CoNiFeMn0.5Cr1.5 alloy and two versions with 0.25C&3.7Ta or 0.25C&3.7Hf were tested in oxidation at 1000°C for 50h with thermogravimetric recording of the oxidation kinetic. In all cases the obtained mass gain curves are parabolic. Their parabolic constants are much lower than the Kp previously determined for the original alloys with an equimolar base (CoNiFeMnCr). However, the post–mortem exploitation of the oxidized samples revealed analogous oxidation features on surface and subsurface, with here too external oxide strata on surface with different Mn and Cr contents, and rather great Mn–depletion in addition to a moderate Cr–depletion, in subsurface. Globally, the oxidation behavior is significantly better than earlier observed for the equimolar version of these alloys.

This paper seeks to examine how the Mn-Co spinel interconnect coating microstructure can in-fluence the Cr contamination in an oxygen electrode of intermediate temperature Solid Oxide Cells at the operating temperature of 750 °C. A Mn-Co spinel coating is processed on Crofer 22 APU substrates by electrophoretic deposition and subsequently sintered following both the one-step and two-step sintering, in order to obtain significantly different densification levels. The electrochemical characterization is performed on anode supported cells with a LSCF cathode. The cells were aged prior to the electrochemical characterization in contact with the spinel coated Crofer 22 APU at 750 °C for 250 hours. Current-voltage and impedance spectra of the cells were measured after the exposure with the interconnect. Post-mortem analysis of the interconnect and the cell was carried out in order to assess the Cr retention capability of coatings with different microstructures.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

The usage of biotechnological molecules and processes is an indispensable part of the resource technology research. The development of novel biomolecules therefore needs to be adapted to the existing applicational conditions and biological processes are to be examined. Novel biosorbents may not only contribute to future applications but can be of further used, e.g. to better understand the interaction of known metal- and metalloid-interacting biological molecules and materials. This review highlights biotechnological approaches published so far for bioremediation as well as metal recovery with a special spotlight on cobalt, nickel and arsenic.

Pt-coated Ni layer supported on Ni foam catalyst (denoted PtNi/Nifoam) was investigated for the oxidation of the formic acid (FAO) in acidic media. The prepared PtNi/Ni foam catalyst was studied as a function of the formic acid (FA) concentration at bare Pt and PtNi/Nifoam catalysts. The catalytic activity of the PtNi/Nifoam catalysts, studied on the basis of the ratio of the direct and indirect current peaks (jd)/(jnd) for the FAO reaction, showed values about 10 times higher compared to those on bare Pt, particularly at a low formic acid concentrations, reflecting the superiority of the former catalysts for the oxidation of FA to CO2. Ni foams provide a large surface area for the FOR while synergistic effects between Pt nanoparticles and Ni-oxy species layer on Ni foams contribute significantly to the enhanced oxidation of FA via the direct pathway, making it almost equal to the indirect pathway, particularly at low formic acid concentrations.

The Ni-laterite deposit at the San Felipe plateau, located 30 km northwest of Camagüey, in cen-tral Cuba, is the best example of a clay-type deposit in the Caribbean region. San Felipe resulted from weathering of mantle peridotites of the Cretaceous Camagüey ophiolites. In this study, a geochemical and mineralogical characterization of two profiles (83 and 84) from the San Felipe deposit has been performed by XRF, ICP-MS, quantitative XRPD, oriented aggregate mount XRD, SEM, FE-SEM and EMPA. Core 83 with a length of 23 m, and drilled in the central part of the plateau, presents a notable concentration of cryptocrystalline quartz fragments and a rather poor content in NiO, averaging 0.87% wt. Core 84, which is 12 m long, and drilled at the border of the plateau, lacks silica fragments and presents a higher NiO content, averaging 1.79 %wt. The smectite structural formulae reveal that they evolve from trioctahedral to dioctahedral towards the top of the laterite profiles. Quantitative XRD analyses indicate that smectite is a dominant Ni bearing phase, accompanied by serpentine and minor chlorite. Serpentine, as smectite, is en-riched in the less soluble elements Fe3+, Al and Ni towards the top of the profiles. Core 83 seems to have been affected by collapses, replenishments, whereas core 84 may have remained undis-turbed.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

Within the study, magnetic/polyetherimide-acrylonitrile composite nanofibers membrane with effective adsorption of nickel ions in aqueous solution were established, through a simple electrospinning method. Iron oxide nanoparticles were stirred and ultrasonically dispersed into polyetherimide-acrylonitrile solution for homogenous suspension. Afterwards, the polyetherimide-acrylonitrile solution with uniform suspension of iron nanoparticles was used in electrospinning machine to produce uniform and smooth nanofibers composite membrane. The confirmation of nanoparticles incorporation into polymeric membrane were characterized by SEM, EDX, FTIR, XRD and nanoparticles aqueous stability through leach out test. The high adsorption capability of the composite membranes on nickel ions was mainly attributed to the combination of magnetic nanoparticles, polyetherimide-acrylonitrile matrix and nano-sized structure of membrane. Membrane containing magnetic nanoparticles demonstrate the maximum adsorption capabilities (102 mg/g) for nickel ions from aqueous solution. Different kinetics and isotherm models were applied to understand the adsorption behavior during adsorption process, amongst them pseudo second order kinetic and Langmuir isotherm model were well fitted. Additionally, EDX, FTIR and XRD results confirmed the presence of nickel ions onto membrane after adsorption process. Polyetherimide-acrylonitrile composite nanofibers membranes containing magnetic nanoparticles may use as an environmentally-friendly and non-toxic adsorbent for the removal of nickel ions in aqueous medium due to its ease of preparation, easy to use and stability in aqueous medium by retaining the nanoparticles inside the nanofibers membranes.

Results are presented concerning the influence on the water splitting process of enantiopure tartaric acid present in bulk solution. Stainless steel and electrodeposited nickel are used as working electrode (WE) surface. The latter is obtained by electrodeposition on the two poles of a magnet. The influence and role played by the chiral compound in solution has been assessed by comparing the current values, in cyclic voltammetry (CV) experiments, recorded in the potential range at which oxygen evolution reaction (OER) occurs. In the case of tartaric acid and nickel WE a spin polarization of about 4 % is found. The use of the chiral environment (bulk solution) and ferromagnetic chiral Ni electrode allows for observing the OER at a more favourable potential: about 50 mV (i.e. a cathodic, less positive, shift of the potential at which the oxygen evolution is observed).

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

The microstructure and solidification behavior of nickel based GTD222 superalloy at different cooling rates are studied. The solidification of the GTD222 superalloy proceeds as follows: L→L+γ, L→L+γ+MC, L→L+(γ/γ ′)-Eutectic and L→η phase. The temperature of liquidus of GTD222 superalloy is 1360 °C while the solidus is slightly lower at 1310 °C, which due to the alloying elements redistribution. It was found that the dendrite arm spacing of the alloy decreased with the increase of cooling rate (From 200 μm at 2.5 K/min to 100 μm at 20 K/min).

Herein, we report about the monometallic Ni and bimetallic Pd-Ni catalysts supported on CeO2-Al2O3 binary oxide, which were investigated in oxy-steam reforming of methanol (OSRM). Monometallic and bimetallic supported catalysts were prepared by wet aqueous impregnation and subsequent impregnation method, respectively. The physicochemical properties of the catalytic systems were investigated using various methods such as: BET, XRD, TPR-H2, TPD-NH3, XPS and SEM-EDS techniques. It has been proven that the addition of palladium to the nickel catalyst facilitates its reduction. The activity tests performed for all catalysts confirmed the promotion effect of palladium on catalytic activity of nickel catalyst and selectivity towards hydrogen production. Both nickel and bimetallic palladium-nickel supported catalysts showed excellent stability during the reaction. Such catalytic systems are valuable for the advance of the field of fuel cell technology.

Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.

Sorghum is a multipurpose crop, but Cr(VI) toxicity influenced the production of the crop and have established highlighted courtesy, due to robust toxicity and a comparatively less known mode of action. Many reports approve the negative impact of Cr(VI) on plants. Yet, it is not clear that, at what concentrations, Cr(VI) inhibits the growth and nutrient quality of Sorghum. In the present research, toxic effects appeared after 1ppm of Cr treatment. The plant growth decreased 15 – 20% and nutritional quality decreased 30 – 40% significantly with increasing concentration of Cr(VI). Toxic components increased 14 – 16% with increasing concentration of Cr(VI) in both the varieties (HJ 541 and SSG 59-3). Chromium was accumulated more in roots followed by shoots with increasing Cr(VI) treatments (0-4 ppm). Chromium at 4ppm level was becoming lethal to Sorghum. Sorghum cultivar SSG 59-3 was more tolerable to Cr toxicity than HJ 541. Chromium accumulated in Sorghum and increased HCN content and at higher doses adversely affects the nutritive values and growth making it toxic for animal consumption. These findings may be useful for scheming a mitigation strategy for chromium toxicity.

Nitride and carbide are the second phases which play an important role in the performance of bearing steel, and their precipitation behavior is complicated. In this study, TiN-MC_x precipitations in GCr15 bearing steels were obtained by non-aqueous electrolysis, and their precipitation mechanisms were studied. TiN is the effective heterogeneous nucleation site for Fe₇C₃ and Fe₃C, therefore, MC_x can precipitate on the surface of TiN easily, its chemistry component consists of M₃C and M₇C₃ (M = Fe, Cr, Mn) and Cr₃C₂. TiN-MC_x with high TiN volume fraction, TiN forms in early stage of solidification, and MC_x precipitates on TiN surface after TiN engulfed by the solidification advancing front. TiN-MC_x with low TiN volume fraction, TiN and MC_x form in late stage of solidification, TiN can not grow sufficiently and is covered by a large number of precipitated MC_x particles.

Hybrid organic/inorganic conducting and magnetic composites of core–shell type have been prepared by in-situ coating of nickel microparticles with polypyrrole. Three series of syntheses have been made. In the first, pyrrole was oxidized with ammonium peroxydisulfate in water in the presence of various amounts of nickel and the composites contained up to 83 wt% of this metal. The similar syntheses in 0.1 M sulfuric acid followed. Finally, the composites with polypyrrole nanotubes were prepared in water in the presence of structure-guiding methyl orange dye. FTIR and Raman spectroscopies confirmed the formation of polypyrrole. The resistivity of composite powders of the order of tens to hundreds Ω cm was monitored as a function of pressure up to 10 MPa. The resistivity of composites slightly increased with increasing content of conducting nickel. This apparent paradox is explained by the coating of nickel particles, which prevents their contacts and generation of metallic conducting pathways. Electrical properties were practically independent of the way of composite preparation or nickel fraction and were controlled by polypyrrole phase. On the contrary, magnetic properties were determined exclusively by nickel content. The composites were used as a solid phase to prepare a magnetorheological fluid. The test showed better performance when compared with a different nickel system.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Current hydrogen production is based on the reforming process leading to the emission of pollutants; therefore, a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production, as it does not produce any carbon-based pollutant byproducts. Production of green hydrogen from water electrolysis using intermittent sources (e.g., solar, eolic) would facilitate clean energy storage. However, the electrocatalysts currently required for water electrolysis are noble metals, making this potential option expensive and inaccessible for industrial applications. Therefore, there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms, structure, and morphology. Even though some works tend to be contradictory, they have lit up the path for efficient nickel-based electrocatalysts. For these reasons, herein, a review of recent progress is presented.

The removal of chromium(VI) from acidic (HCl) medium through non-dispersive extraction with strip dispersion (NDXSD) was investigated using a microporous PVDF membrane support in a permeation cell. The ionic liquid Cyphos IL102 (phosphonium salt) in Solvesso 100 was used as organic phase. In NDXSD the stripping phase (NaOH) is dispersed in the organic phase in the cell side with an impeller stirrer adequate to form a strip dispersion. This pseudo-emulsion phase (organic + strip solutions) provides a constant supply of the Cyphos IL102/Solvesso 100 to the membrane phase. Various hydrodynamic and chemical parameters, such as variation in the feed and pseudo-emulsion stirring speeds, HCl and Cr(VI) concentrations in the feed phase, and carrier concentration, were investigated. From the experimental data, several mass transfer coefficients were estimated, as well as it was investigated the performance of the present system against other ionic liquids and the presence of base metals in the feed phase.

Abstract Aims: In recent years, electro kinetic (EK) remediation has become more popular as a novel method for removing chromium contamination from soil. This approach, however, is ineffective since it uses both cationic and anionic forms of chromium. In this work, a membrane –based technique was employed to increase the efficiency of the electro kinetic removal of chromium. Methods: Chromium removal from polluted sludge was studied in four bench-scale experiments, two of which used distilled water (EK-1, EK2 & Membrane) and two of which used acetic acid as a catholyte (EK-3, EK4 &Membrane). Results: The pH, total chromium, and fractionation of chromium in the sludge were measured after remediation. In the EK-1, EK-2 & Membrane and EK-3, EK-4 & Membrane trials, the average removal efficiency of total chromium was 47.6%, 58.6%, and 74.4%, 79.6%, respectively. Conclusion: In contrast to the electro kinetic remediation strategy, which left approximately 80% of the sludge neutral or alkaline after treatment, the use of the membrane created acidic soil conditions throughout the sludge. For example, the high field intensity used in the membrane tests may have helped to facilitate chromium desorption, dissolution and separation from the sludge, as well as enhance chromium mobility. The findings show that the membrane can improve the effectiveness of chromium removal from sludge when utilized in the EK remediation process.

In this study, vermiculite was explored as a support material for nickel catalysts in two key processes in syngas production through dry reforming of methane with CO2 and steam reforming of ethanol. The vermiculite was subjected to acid or base treatment, then, Ni catalysts were prepared through incipient wetness impregnation and characterized using various techniques, including X-ray, FTIR, temperature programmed reduction (H2-TPR). TG-TD analyses were performed to assess the formation of carbon deposits on spent catalysts. The Ni based catalysts were used in the reaction tests without a reduction pre-treatment. Initially, raw vermiculite-supported nickel showed limited catalytic activity, however after acid (Ni/VTA) or base (Ni/VTB) treatment, vermiculite became an effective support for nickel in dry methane reforming. The resulting catalysts (Ni/VTB and Ni/VTA) displayed outstanding performance, with high methane conversion and hydrogen yield. Acidic treatment improved the reduction of nickel species and reduced carbon deposition, outperforming alkali treatment. The prepared catalysts were also explored in ethanol steam reforming. The performance was investigated as a function of the temperature, water/ethanol ratio, and space velocity, with acid-treated catalysts performing as the best. The study emphasized the importance of contact time with the catalyst and addressed challenges related to carbon formation and sintering for long-term stability. In conclusion, acidic treatment of the vermiculite support, before Ni deposition, significantly enhanced the catalytic activity and stability of nickel catalysts in both dry methane reforming and ethanol steam reforming processes.

There is currently much interest in avoiding precious metals in Catalysis. The devel-opment of nickel catalysts to replace palladium in the Mizoroki-Heck reaction is a relevant case in this line of research since both elements share many chemical features. This contri-bution focuses on -Phenyl elimination in alkylnickel complexes. This is the microscopic reverse of olefin insertion (or carbometallation), a fundamental step of the Heck cycle that is usually considered irreversible and selectivity-determining. However, the potential reversibil-ity of carbometallation is generally concealed by the facile beta-hydrogen elimination that follows. Where -hydrogen elimination is hindered, beta-aryl elimination may ensue. We have previously shown that cationic 2-methyl-2-phenylpropyl (neophyl) palladium com-plexes supported by bidentate ligands experience -Ph elimination, which can be seen as an example of olefin de-insertion. In this contribution, we report that -phenyl elimination can also occur in their nickel analogs, in which case fast hydrolyses of the resulting phenyl product can follow the reaction. We investigated the mechanism of these processes and compared their feasibility for nickel and palladium catalysts using DFT calculations. These results are relevant information for the design of nickel-based catalysts for the Heck reac-tion.

In order to study the feasibility of copper-nickel smelting slag（CNSS） and palygorskite for large-scale consumption and utilization in the field of mine filling, gellable composite materials were prepared from copper-nickel smelting slag ,cement and palygorskite. The effects of palygorskite addition and curing time on the mechanical properties and microstructure of copper-nickel smelting slag-based cementitious materials were studied in detail. The results showed that the addition of palygorskite had a positive effect on the curing of the cemented filler of the non-ferrous smelting slag by promoting the early hydration reaction. palygorskite also affected the mechanical properties of the cementitious materials with different maintenance times and the ability to cure heavy metals. The strength of gellable composite materials reaches 23.05MPa when 1% palygorskite, 50% of copper-nickel smelting slag and 48% cement were used, which meet the standards requirements of filling materials for mine goaf. The addition of 1% palygorskite can improve the ability of cementitious materials to solidify heavy metals to realize the economic utilization of solid waste in mining areas.

This manuscript presents the result of utilizing cellulose as a template to prepare na-nosized WO3-NiWO4 and its application as co-catalysts in Pt/WO3-C and Pt/WO3-NiWO4-C for ethanol and glycerol electro-oxidation. Microcrystalline cellulose was hydrolyzed with phosphotungstic acid (H3PW12O40) to prepare the nanosized template of crystalline cellulose. Next, the template was impregnated with Ni(NO3)2, rendering a precursor mate-rial that is subsequently air-calcinated, removing the carbon-template material to obtain the nanometric WO3 and NiWO4. Elemental analysis confirmed the coexistence of nickel and tungsten, whereas the thermal analysis evidenced the high thermal stability of these materials. The X-ray diffractograms displayed crystal facets of WO3 and, when added Ni, of NiWO4. The transmission electron micrographs corroborated the formation of na-nosized particles with average particle sizes close to 50 nm. Finally, to apply this material, Pt/WO3-C and Pt/WO3-NiWO4-C were prepared and used in ethanol and glycerol electro-oxidation in alkaline medium, observing a promotional effect of the oxide and tungstate by reducing the onset potential and increasing the current density. These materials show great potential to produce clean electricity or green hydrogen contributing to energetic transition.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

There is a high iron content in the nickel slag that mainly exists in fayalite phase. Basic Oxide can destroy the stable structure of fayalite which is beneficial to the treatment and comprehensive utilization of nickel slag. The reseach was based on the composition of the raw nickel slag, taking CaO-SiO₂-FeO-MgO system as the object and CaO as a modifier. The effect of basicity on the melting characteristics, viscosity and structure of CaO-SiO₂-FeO-MgO system was studied. The relationship between the viscosity and structure of CaO-SiO₂-FeO-MgO system was also explored. The results show as follows. (1) When the basicity is 0.38~0.90, the phase of primary crystal is olivine at argon atmosphere, while it is monoxide at the basicity of 0.90~1.50. The liquidus temperature, softening temperature, hemispherical temperature, and flow temperature all reach the lowest value at the basicity of 0.90. (2) With the increase of basicity, critical viscosity temperature of CaO-SiO₂-FeO-MgO system decreases first and then increases. Critical viscosity temperature is the lowest at the basicity of 0.90, which is 1263 ℃. (3) When the slag system is heterogeneous, the viscosity of the molten slag increase rapidity because of the type and quantity of solid phase precipitated from CaO-SiO₂-FeO-MgO system. And critical viscosity temperature of the slag system is also significantly affected. (4) When the slag system is in a homogeneous liquid phase, the molar fraction of O0 decreases with the increase of basicity and the mole fraction of O^- and O^2- increases continuously at the basicity of 0.38~1.50. The silicate network structure is gradually depolymerized into simple monomers, resulting in the degree of polymerization is reduced and the viscosity is reduced, too.

The possibility of applying Mo and Cr coatings by CVD method to the inner surfaces of tubular products Ø ˂ 60 mm has been studied.The process of applying Mo and Cr coatings by the method of gas-phase deposition was developed.The areas of parameters for obtaining coatings with a uniform structure, speed, hardness, as well as patterns of change in these characteristics when changing the main parameters of the process of obtaining such coatings are determined.The proven technological processes of applying Mo and Cr CVD coatings can be the basis for the development of pilot technologies for applying functional coatings to precision parts with small-diameter inner tubular surfaces in the mechanical engineering and aviation industries.A controlled process of applying two-component chromium-aluminum coatings by gas-phase deposition using organic and organometallic substances was developed. Optimization of the processes of applying high-quality two-component chromium-aluminum coatings on prototype models of the internal cavities of cooled turbine blades was carried out.The studies revealed the characteristics of two-component chromium-aluminum coatings comparable to those of coatings used in production, while ensuring good quality coatings in terms of adhesion strength to the turbine blade material. The reproducibility of the coatings obtained makes it possible to develop pilot technologies for production in the future.The lower toxicity of the precursors used makes it possible to create an environmentally friendly technology and significantly reduce environmental problems in production when applying two-component chromium-aluminum coatings to the internal cavities of cooled turbine blades.

Porosity in plasma sprayed coatings is vital for most engineering applications. It is either advantageous or disadvantageous depending on the functionality of the coating and the immediate working environment. Consequently, the formation mechanisms and development of porosity has been extensively explored to find out modes of controlling porosity in plasma sprayed coatings. In this work, a comprehensive review of porosity on plasma sprayed coatings is established. The formation and development of porosity on plasma sprayed coatings are governed by set spraying parameters. Optimized set spraying parameters have been used to achieve the most favorable coatings with minimum defects. Even with the optimized set spraying parameters, defects like porosity still occur. Here, we discuss other ways that can be used to control porosity in plasma sprayed coating with emphasis to atmospheric plasma sprayed chromium oxide coatings. Techniques like multi-layer coatings, nano-structured coatings, doping with rare earth elements, laser surface re-melting and a combination of the above methods have been suggested in adjusting porosity. The influences of porosity on properties of plasma sprayed coatings and the measurement methods of porosity have also been reviewed.

The limitations of investment casting of cobalt-based alloys are claimed to be less problematic with significant improvements in metal additive manufacturing by selective laser melting (SLM). Despite these advantages, the metallic devices are likely to display mechanical anisotropy in relation to build orientations, which could consequently affect their performance ‘in vivo’. In addition, there are inconclusive evidence concerning the requisite composition and post-processing steps (e.g. heat-treatment to relieve stress) that must be completed prior to the devices being used. In the current paper, we evaluate the microstructure of ternary cobalt-chromium-molybdenum (Co-Cr-Mo) and cobalt-chromium-tungsten (Co-Cr-W) alloys built with Direct Metal Printing and LaserCUSING SLM systems respectively at 0°, 30°, 60° and 90° inclinations (Φ) in as-built (AB) and heat-treated (HT) conditions. The study also examines the tensile properties (Young's modulus, E; yield strength, R_P0.2; elongation at failure, A_t and ultimate tensile strength, R_m), relative density (RD), and micro-hardness (HV5) and macro-hardness (HV20) as relevant physico-mechanical properties of the alloys. Data obtained indicate improved tensile properties and HV values after short and cost-effective heat-treatment cycle of Co-Cr-Mo alloy; however, the process did not homogenize the microstructure of the alloy. Annealing heat-treatment of Co-Cr-W led to significant isotropic characteristics with increased E and A_t (except for Φ = 90º) in contrast to decreased R_P0.2, R_m and HV values, compared to the AB form. Similarly, the interlaced weld-bead structures in AB Co-Cr-W were removed during heat-treatment, which led to a complete recrystallization in the microstructure. Both alloys exhibited defect-free microstructures with RD exceeding 99.5%.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

Nickel is widely used in industrial processes and plays a crucial role in many applications. However, most of the nickel resource mainly exists as nickel oxide in laterite nickel ore with complex composition, resulting in difficulty in upgrading the nickel content using physical separation methods. In this study, high-grade ferronickel concentrates were obtained through a carbothermal reduction and magnetic separation using laterite nickel ore and anthracite as raw materials. The effects of different types of additives (CaF2, Na2SO4 and H3BO3), carbon ratio (nc/no in metal oxides) and grinding time on the recoveries and grades of ferronickel concentrates were experimentally investigated, along with the microstructure and chemical composition of the products. CaF2 was proved to be the primary active additive in the aggregation and growth of the ferronickel particles, and the improvement of the grade of the product. Under the optimal conditions of CaF2 addition of 12 wt.%, carbon ratio of 1.4, and grinding time of 240 s, high-grade magnetically separable ferronickel concentrate with nickel grade 8.93 wt.% and iron grade 63.96 wt.% was successfully prepared. This work presents a practical method for the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore, contributing to the development of strategies for the sustainable extraction and utilization of nickel resources.

Nickel-based superalloys are attractive to many industrial sectors (automotive, military, energy, aerospace etc.). However, their physical properties make them difficult to machining using traditional tools. Therefore, the new materials for the machining of Ni-based alloys are required. Ceramic-based composites could act as a tool to replace the current materials. The incentives for this paper are to provide an overview of existing ceramic composites and draw some conclusions that will help in solving the problem of choosing materials for processing of Ni-based superalloys. Despite the diversity of ceramic composites in this work the focus was on the SiAlON ceramic.

The Ni-Co-Cr-W-Mo system is critical for the design of nickel-based super-alloys. This system stabilizes different topologically close packed (TCP) phases in many of the commercially super-alloys with high W and Mo contents. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermodynamic calculations are applied to investigate the thermodynamics of the precipitates in two different W content Ni-Co-Cr-W-Mo super-alloys. Computational thermodynamics verified experimental observation of the f u phase formation as a function of temperature and alloy chemistry, but the kinetics for the precipitation of M6C phase do not agree with the experimental findings. The major precipitates of alloy 1 at temperatures 700 and 750 °C during long time exposure are M23C6, γ′ phase, and MC, and alloy 2 are M23C6, γ′ phase, MC, M6C and u phase. The W addition is found to promote the precipitation of M6C and u phase during exposure. The M6C has higher W and lower Ni content than that of u phase, meanwhile, M6C is an unstable phase would transform into M12C after 5000 h exposure at 750 °C. A great quantity of needle-like u phases precipitated after exposure at 750 °C for 5000h, which have no effect on the impact property of alloy 2.

This article reports the two-step synthesis of NiFeO_x nanomaterials, their characterisation and bifunctional electrocatalytic activity measurements in alkaline electrolyte for metal-air batteries. The samples were mostly in layered double hydroxide at the initial temperature, but upon heat treatment, they were converted to NiFe₂O₄ phases. The electrochemical behaviour of the different samples was studied by linear sweep voltammetry and cyclic voltammetry on the glassy carbon electrode. The OER catalyst activity was observed for low mass loadings (0.125 mg cm⁻²), whereas high catalyst loading exhibited the best performance on the ORR side. The sample heat treated at 250 °C delivered the highest bi-functional oxygen evolution and reduction reaction activity (OER/ORR) thanks to its thin-holey nanosheet like structure with higher nickel oxidation state at 250 °C. This work further helps to develop low-cost electrocatalyst development for metal-air batteries.

The objective of this study is to design and synthesize substituted η6-chromium tricarbonyl metal complexes carrying o-carborane units as potential boron neutron capture therapy (BNCT) agents. In this study, 1,2-Diphenyl-o-carborane units were used as starting materials to generate biologically active species. We investigated how the structural changes of 1,2-diphenyl-o-carborane substituted with chromium(0) tricarbonyl affect the biological properties; [(CO)3Cr]Ph2C2 (2) and [(CO)3Cr]2Ph2C2 (3) species were produced in moderate yields. The molecular structures of compounds 1–3 were identified and established by infrared (IR), 1H, 11B, and 13C nuclear magnetic resonance (NMR), and X-ray crystallography analyses. Crystal structures of o-carboranyl chromium complexes 1 [a = 10.859(1) Å, b = 24.953(3) Å, c = 13.938(2) Å, β = 111.854(2)º], 2 [a = 10.621(3) Å, b = 17.056(5) Å, c = 12.174(4) Å, β = 106.622(5)º], and 3 [a = 17.540(2) Å, b = 18.060(2) Å, c = 19.484(4) Å, α = 105.746(2)º, β = 110.226(2)º, γ = 91.256(2)º] were obtained. In vitro study using B16 and CT26 cancer cells containing the triphenyl-o-carboranyl chromium (0) complexes Ph3C2BCr2 and Ph3C2BCr3, which we have previously reported, the compounds 2 and 3 accumulated at higher levels than compounds Ph3C2BCr2 and Ph3C2BCr3. However, the phenylated o-carboranyl chromium(0) complexes have been found to be more cytotoxic than p-boronophenylalanine (BPA).

Environmental and occupational exposure to hexavalent chromium, Cr(VI), causes female reproductive failures and infertility. Cr(VI) is used in more than 50 industries and is a group-A carcinogen, mutagenic and teratogenic, and a male and female reproductive toxicant. Our previous findings indicate that Cr(VI) causes follicular atresia, trophoblast cell apoptosis, and mitochondrial dysfunction in metaphase II (MII) oocytes. However, the integrated molecular mechanism of Cr(VI)-induced oocyte defects are not understood. The current study investigates the mechanism of Cr(VI) in causing meiotic disruption of MII oocytes, leading to infertility in superovulated rats. Postnatal day (PND)-22 rats were treated with potassium dichromate (1 and 5 ppm) in drinking water from PND 22-29 and superovulated. MII oocytes were analyzed by immunofluorescence, and images were captured by confocal microscopy and quantified by Image Pro Plus software. Our data showed that Cr(VI) increased microtubule misalignment, missegregation of chromosomes, a bulged and folded actin cap, oxidative DNA and protein damage, increased DNA double-strand break, and DNA repair protein RAD51. Cr(VI) also induced incomplete cytokinesis and delayed polar body extrusion. Our study indicates that exposure to environmentally relevant doses of Cr(VI) caused severe DNA damage, distorted oocyte cytoskeletal proteins, and caused oxidative DNA and protein damage leading to infertility.

A gold nanostructured film modified glassy carbon electrode (Au_film/GCE) was developed for the determination of chromium (VI) in water sample. GCE was immersed into HAuCl₄ solution (10^-3M) and electrodeposition of thin gold layer was conducted at –0.4 V (vs Ag/AgCl) for 10 min. The strong affinity between Au and Cr species resulted with increasing of Cr (VI) signal, compared with the bare glassy carbon electrode. The electrodepositing time, type of supporting electrolyte, pH, the scan rate, modulation amplitude, and modulation time were optimized using differential pulse anodic stripping voltammetry (DP-ASV). The calibration graph using accumulation time of 120 s was linear from 10 to 120 µgL^-1 with a sensitivity 1.3 x 10^-2 µA/µgL^-1. Under optimum experimental conditions, a good correlation coefficient R²=0.9971, and a low detection limit 5.5 µg/L Cr (VI) was obtained. The signal was reproducible with a relative standard deviation ±4.5 %. The developed Au_film/GCE sensor was applied for the Cr (VI) determination of in sewage water samples.

The paper presents the numerical and experimental results of research aimed at determining the influence of hardness in the range of 50-90 Shore A of layered tools made of elastomeric materials on the possibility of forming Inconel 625 nickel-based alloy sheets. A stamping die made of 90MnCrV8 steel (hardness 60HRC) was designed for forming embosses in drawpieces, ensuring various stress states on the cross-section of the formed element. The principle of operating the stamping die was based on the Guerin method. Finite element-based numerical modelling of the forming process for various configurations of polyurethane inserts was also carried out. The drawpieces obtained by sheet forming were subjected to geometry tests using optical 3D scanning. The results confirm that in the case of forming difficult-to-deform Inconel 625 Ni-based alloy sheets, the hardness of the polyurethane inserts significantly affects the geometric quality of the obtained drawpieces. The assumptions made in numerical simulations were verified in experimental studies. Based on the test results, it was concluded that the selection of polyurethane hardness should be determined by the shape of the formed element. Significant non-uniform sheet metal deformation was also found, which may pose a problem in the process of designing forming tools and technology of plastic forming of Inconel 625 Ni-based alloy sheets.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

Nickel-based Superalloy Inconel 718 is widely used in the aerospace industry for its excellent high-temperature strength and thermal stability. However, milling Inconel 718 presents challenges due to significantly increased cutting force and vibration, which is a typical difficult-to-machine material. This paper focuses on the milling process of Inconel 718, establishing a milling force model to analyze the force trends under various processing parameters. Finite element analysis is employed to study the stress and temperature fields during milling. Dynamic equations for milling Inconel 718 are developed, and stability lobe diagrams are generated based on modal experiments. Milling experiments on Inconel 718 validate the milling force model and finite element analysis results. The fmincon optimization algorithm is utilized to identify the optimal machining parameters for Inconel 718. Through this research, valuable insights into enhancing the efficiency and quality of Inconel 718 machining are provided. This study contributes to a deeper understanding of Inconel 718 milling behavior, offering crucial guidance for more efficient machining processes.

Abstract: Interactions in multicomponent Ni-Cr-Mo-Al-Re model alloy were determined by ab initio calculations in order to investigate the Re doping effect on Haynes 282 alloy. Simulation results provided an understanding of short-range interactions in the alloy and successfully pre-dicted the formation of a Cr and Re-rich phase. The Haynes 282 + 3 % wt. Re alloy was manu-factured using the additive manufacturing Direct Metal Laser Sintering (DMLS) technique, in which the presence of the (Cr17Re6)C6 carbide was confirmed by an XRD study. The results ob-tained provide useful information about the interactions between Ni, Cr, Mo, Al, and Re as a function of temperature. The 5-element model designed can lead to a better understanding of phenomena that occur during the manufacturing or heat treatment of modern, complex, multi-component Ni-based superalloys.

Metal-organic frameworks (MOFs) are investigated for the oxygen evolution reaction (OER) due to their structure diversity, high specific surface area, adjustable pore size and abundant active sites. However, the poor conductivity of most MOFs restricts this application. Herein, through a facile one-step solvothermal method, the Ni-based pillared metal-organic framework [Ni2(BDC)2DABCO] (BDC = 1,4-benzenedicarboxylate, DABCO = 1,4-diazabicyclo[2.2.2]octane), its bimetallic nickel-iron form [Ni(Fe)(BDC)2DABCO] and their modified Ketjenblack (mKB) composites were synthesized and tested towards OER in an alkaline medium (KOH 1 mol L–1). A synergistic effect of the bimetallic nickel-iron MOF and the conductive mKB additive enhance the catalytic activity of the MOF/mKB composites. All MOF/mKB composite samples (7, 14, 22, 34 wt.% mKB) indicated much higher OER performances than the MOFs and mKB alone. The Ni-MOF/mKB14 composite (14 wt. % of mKB) demonstrated an overpotential of 294 mV at a current density of 10 mA cm–2 and Tafel slope of 32 mV dec–1, which is comparable with commercial RuO2 commonly used as a benchmark material for OER. The catalytic performance of Ni(Fe)MOF/mKB14 (0.57 wt% Fe) was improved further to an overpotential of 279 mV at a current density of 10 mA cm–2. The low Tafel slope of 25 mV dec–1 as well as a low reaction resistance due to electrochemical impedance spectroscopy (EIS) measurement confirm the excellent OER performance of the Ni(Fe)MOF/mKB14 composite. For practical applications, the Ni(Fe)MOF/mKB14 electrocatalyst was impregnated into commercial nickel foam (NF), where overpotentials of 247 and 291 mV at current densities of 10 and 50 mA cm–2, respectively, were realized. The activity was maintained for 30 h at the applied current density of 50 mA cm–2. The electrocatalytic system consisting of earth-abundant Ni and Fe metals only would be attractive for the development of efficient, practical and economical energy conversion materials for efficient OER activity.

Nickel foam substrates are frequently utilised for renewable energy applications as porous 3D-substrates. Preparation of these substrates usually includes an acid washing step, however the degree to which this step affects the final electrochemical performance after spray coating a catalyst ink is unreported. Herein, we report the effect of acid washing through physicochemical and electrochemical characterisation. The electrochemical performance was determined by repeated measurements of catalyst-coated nickel foam substrates both with and without the initial step of acid washing. Acid washing increased current density by 17.9% for the acid treated, MoS2-coated nickel foam electrode. This increment was affiliated with an electrochemically active surface area which increased by 87.1%, where Tafel analysis indicated that the acid treated, MoS2-coated electrodes facilitates the initial water dissociation step of the hydrogen evolution reaction with greater ease. Similar effects were also discovered for acid treated PtIr(1:3)/C-coated nickel foam substrates, albeit with less pronounced effects. Stability was also improved where the degradation rate was reduced by 18.9% for the acid treated, MoS2-coated electrodes. This proves the utility of acid washing nickel foam electrodes.

Algal-bacterial granular sludge, a new biological technology, has been widely recognized due to its highly effective pollutant treatment and energy efficiency. This study investigated the effects of environmental concentrations of Cr(VI) (0.5-2.5 mg/L) on the performance of algal-bacterial gran-ular sludge and self-defensive responses after 90 days of cultivation. The results showed that Cr(VI) affected chemical oxygen demand (COD), ammonia-N and phosphate removal with different trends being apparent. A linear decline in COD removal was observed, whereas an initial de-creasing and then increasing ammonia-N and phosphate removal took place. Algal-bacterial granular sludge effectively removed Cr(VI) from wastewater through biological adsorption and reduction, showing the potential to treat Cr(VI)-contaminated wastewater. Cr(VI) affected the community abundance of the algal-bacterial granular sludge, in which Chlorophyceae and cya-nobacteria were vulnerable under Cr(VI)-induced stress. To reduce the toxicity of Cr(VI), over-produced EPS-PN and antioxidant enzymes (MDA, SOD and CAT) acted as self-defensive responses to resist oxidative damage. This study showed that algal-bacterial granular sludge can remove 00.5 mg/L of Cr(VI) without performance loss. It is hoped that this study can provide useful information for improved engineering feasibility of algal-bacterial granular sludge.

Chromium (VI) is carcinogenic through intermediates formed in the cellular milieu by reduction with small reductants like glutathione (GSH), ascorbate (As), cysteine (Cys) and NADPH. Although the reduction of chromate by thiols have been investigated, the participation of Cr(IV) intermediates has been inferred only indirectly due to its refractive behavior towards EPR spectroscopy and the lack of true chromium (IV) complexes for comparative studies. Biological data from numerous reports indicate that Cr(IV) is the species most likely responsible for the carcinogenicity of Cr(VI). Our kinetic studies suggested that in acidic solutions the reduction of chromate with GSH affords mostly a chromium(IV) intermediate. As a step towards the full characterization of the paramagnetic species involved in the reduction of chromate by thiols at neutral pH, we embarked in the investigation of this reaction using the Superconducting QUantum Interference Device (SQUID) Magnetic Property Measuring System®. Our results indicate a strong influence of the temperature. At 2K, the saturation magnetization method was applied to the frozen reaction when it reached the peak of formation of intermediates. Contrary to our expectations, the contributions were calculated to be 30 % of Cr(IV) and 69 % of Cr(V) at this pH. When the Curie-Weiss method was utilized, the effective magnetic moment was dependent on the portion of the data utilized and generally higher proportion of Cr(IV) was found when the fitting is performed with data from higher temperature.

The creation of nano-zero-valent iron (nZVI) by implementing plant extracts is an environmentally friendly process. High antioxidant capacity and phenol content indicated the possibility of oak-nZVI synthesis using oak leaf extract as a stable material with minimal agglomeration. Simultaneously removal of Cd and phosphates and Ni and phosphates was optimized by a statistically designed experiment with a definitive screening design. In terms of significance, 4 input parameters on process productivity were monitored: initial metal concentration (1 - 9 mgL-1), initial ion concentration (1- 9 mgL-1), pH value (2 - 10) and oak-nZVI dosage (2 - 16 ml). Phosphate removal efficiency, in the presence of cadmium, was the most influenced by oak-nZVI dose and cadmium concentration, while pH gave three statistically significant interactions with oak-nZVI dosage, cadmium concentration, and phosphate concentration. Phosphate removal efficiency, in the presence of Ni, is the most influenced by nickel concentration, phosphate concentration, pH, two-factor interaction between nZVI dose and Ni concentration, and quadratic phosphate interaction. The process optimization yielded the highest simultaneous removal efficiency of 98.99% and 87.30% for cadmium and phosphate ions, respectively. Also, the highest simultaneous removal efficiency of nickel and phosphates ion was 93.44% for 96.75%, respectively. The optimization process fits into the confidence intervals, confirming the assumption that the adopted regression model describes the process well. This work demonstrated an enormous potential and prosperous application for the Cd(II), Ni(II), and phosphate removal from water matrices.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

Inclusions in steels and alloys are known as factors that could lower deformation, mechanical, corrosion and other properties. Study of inclusions in nickel based alloys is important since these materials could suffer from corrosion degradation in harsh operational conditions, where inclusions could lead to a pitting initiation. For estimation of a harmful effect of different inclusions on corrosion resistance of Ni-based alloys, inclusion characteristics (such as composition, morphology, size, number and location) on film filter and dissolution of metal matrix around different inclusions on surfaces of metal samples after electrolytic extraction (EE) were investigated in two samples of industrial Ni-based alloys (alloy 718 and EP718). It was found that both Ni-based alloys have various inclusions: carbides (large size NbTi-C and small multicomponent carbides), nitrides TiNb-N and sulfides (TiNb-S in EP718 alloy). The higher harmful effect on corrosion resistance of metal was detected around sulfides and small carbides containing Mo, W, Cr. Dissolution effect was also observed around large carbides and nitrides, especially around inclusions having size more than 10 µm. Moreover, the dissolution of metal matrix around inclusions and clusters located on the grain boundaries is 2.1-2.7 times larger compared to that for those inclusions inside of grains of the given alloy samples.

The rapidly evolving field of additive manufacturing requires a periodic assessment of the progress made in understanding the properties of metallic components. Although extensive research has been undertaken by many investigators, the data on properties such as hardness from individual publications are often fragmented. When these published data are critically reviewed, several important insights that cannot be obtained from individual papers become apparent. We examine the role of cooling rate, microstructure, alloy composition, and post process heat treatment on the hardness of additively manufactured components. Hardness data for steels and aluminum alloys processed by additive manufacturing and welding are compared to understand the relative roles of manufacturing processes. Furthermore, the findings are useful to determine if a target hardness is easily attainable either by adjusting AM process variables or through appropriate alloy selection.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

Three types of the composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, curing process and physical-mechanical properties. In the first type of composites, manganese-zinc ferrite, nickel-zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile-butadiene rubber. The overall content of the filler, or fillers combinations was kept on 200 phr. Then, carbon black, or carbon fibres, respectively were incorporated into each rubber formulation in constant loading - 25 phr, while the content of magnetic fillers was unchanged - 200 phr. The work was focused on the understanding of correlation among electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding ability of materials was evaluated within the frequency range from 1 MHz to 6 GHz. The study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although, the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites were reached over 6 GHz. The application of carbon based fillers resulted in higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. Though, the composites with filled with ferrites and carbon based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon based fillers caused the improvement in tensile behavior of composites. The study also demonstrated that the higher was the ratio of nickel-zinc ferrite in magnetic fillers combinations, the higher was the absorption shielding performance.

This study presents a combined electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) and Scanning Kelvin Probe Force Microscopy(SKPFM) investigation on the natural passivation process of stainless steels (AISI 316 and AISI 304) and nickel-based alloy (INCONEL 600) as a function of immersion time in an alkaline medium (pH = 13). EIS measurements show an increase in the resistance of the film with increasing immersion time in the electrolyte. After 3 days of immersion, for the three alloys, the films formed constitute an effective barrier to the dissolution of the alloys as shown by AFM and SKPFM. The oxide film growth on each substrates is only influenced by trenches formed during the polishing step and don’t depend on the chemical composition.

A comparative study of the physicochemical properties of natural bentonite clays of Pogodayevо (Republic of Kazakhstan, mod.1) and Dash-Salakhli (Republic of Azerbaijan, mod.2) deposits and modification of the bentonite clay with polyhydroxocations of iron (III) and aluminium (III). It-wasestablished that the modification of natural bentonitesusing polyhydroxocations of iron (III) and aluminium(III) by the method of "co-precipitation" leads to a change in their chemical composition, structural and sorption properties. The results showed that hydroxy-aluminum cations ([Al3O4(OH)24(H2O)12]7+) and poly-hydroxyl-Fe or polyoxo-Fe were intercalated into clay layers, which led to an increase in the values of d001 and specific surface areas compared to those of the original bentonite, from 37 to 120 for the Pogodaevo bentonite and from 51 to 172 respectively for bentonite from the Dash-Salakhli deposit. It is shown that modified sorbents based on natural bentonite are finely porous objects with a predominance of pores of 1.5−6.0 nm in size. As a result, there is a significant increase in the specific surface area of sorbents. Modification of bentonite with polyhydroxocations of iron (III) and aluminium (III) by the "co-precipitation" method also leads to an increase in the sorption capacity of the sorbents obtained with respect to nickel (II) cations. Modified bentonites were used for the adsorption of Ni (II) ions from the model solution. Ni (II) was absorbed in a neutral pH solution. The study of equilibrium adsorption showed that the data are in good agreement with the Langmuir isotherm model. The maximum adsorption capacity of the Ni (II) monolayer obtained from the Langmuir equation was 25.0 mg/g (mod. 1_Al_5-c), 18.2 mg/g (mod. 2_Al_5-c) for Al-bentonite and 16.7 mg/g (mod. 1_Fe_5-c), 10.1 (mod. 2_Fe_5-c) for Fe-bentonite. The kinetics of adsorption is considered. The high content of Al-OH anion exchange centresin them determines the higher sorption activity of Al-modified bentonites.

The paper investigates the influence of ion nitriding on the microstructure, corrosion resistance, and tensile strength at elevated temperatures of Haynes 282 nickel superalloy specimens produced by the Direct Metal Laser Sintering-DMLS technique. Analysis of the specimens’ surface morphology revealed that the ion nitriding process significantly affects the physical and chemical phenomena occurring on the surface of the specimens. Phase composition and stress analysis showed that Haynes 282 nickel alloy specimens produced by the DMLS technique and a chromium nitride layer produced in the ion nitriding process have tensile stress. The layer is also characterized by high nanohardness compared to specimens produced using the classical method (wrought) and DMLS technique. The conducted corrosion resistance tests confirmed the positive effect of the nitrided layer on the corrosion resistance of Haynes 282 nickel alloy produced by the DMLS technique. The ion nitriding process did not significantly affect the elevated-temperature tensile strength of Haynes 282 nickel alloy specimens produced by the DMLS technique.

Difficult-to-cut materials are being increasingly used in many industries because of their superior properties, including high corrosion resistance, heat resistance and specific strength. However, these same properties make the materials difficult to machine using conventional machining techniques. Laser-assisted milling (LAM) is one of the effective methods for machining difficult-to-cut materials. In laser-assisted milling machining occur after the workpiece is locally preheated using a laser heat source. Laser assisted machining has been studied by many researchers on flat workpiece or micro end-milling. However, there is no research on the curved shape using laser assisted milling. This study investigated the use of laser assisted milling to machine a three-dimensional curved shape workpiece based on NURBS. A machining experiment was performed on Inconel 718 using different tool paths (ramping, contouring) under various machining conditions. Finite elements analysis was conducted to determine the depth of cut. Cutting force, specific cutting energy and surface roughness characteristics were measured, analyzed and compared for conventional and LAM machining. LAM significantly improved these machining characteristics, compared to conventional machining. There results can be applied to the laser-assisted machining of various three-dimensional shapes.

In the past decade, under the background of the carbon peaking and carbon neutrality era, the rapid development of new energy vehicles has put forward higher requirements for the performance of strike forces such as battery cycle life, energy density and cost. Lithium-ion batteries have gradually become the mainstream of electric vehicle power batteries due to their excellent energy density, rate performance and cycle life. At present, the most widely used cathode materials for power batteries are lithium iron phosphate (LFP) and ternary nickel-cobalt-manganese (NCM). However, these materials exhibit the bottlenecks that limit the improvement and promotion of power battery performance. In this review, the performance characteristics, cycle life attenuation mechanism (including structural damage, gas generation and active lithium loss, etc.) and improvement methods (including surface coating and element-doping modification) of LFP and NCM batteries are reviewed. Finally, the development prospects of this field are proposed.

The application of diffusion dialysis using various types of ion-exchange membranes for the separation of sulfuric acid and nickel sulfate has been evaluated. The process of dialysis separation of a real waste solution from an electroplating facility containing 252.3 g/L of sulfuric acid, 20.9 g/L of nickel ions and small amounts of zinc, iron, copper ions, etc. has been studied. Heterogeneous cation-exchange membrane containing sulfo groups and heterogeneous anion-exchange membranes with different thicknesses (from 145 μm to 550 μm) and types of fixed groups (4 samples with quaternary amino groups and 1 sample with secondary and tertiary amino groups) are used. The diffusion fluxes of sulfuric acid, nickel sulfate, and the total and osmotic fluxes of the solvent are determined. The use of a cation-exchange membrane does not allow separation of the components, since the fluxes of both components are low and comparable in magnitude. The use of anion-exchange membranes makes it possible to efficiently separate sulfuric acid and nickel sulfate. At the same time, the thin dialysis membrane turns out to be the most effective, as well as the membranes with quaternary amino groups, and the membrane with secondary and tertiary amino groups proved to be the least effective.

Sputtered reactive multilayers applied as a heat source in electronic joining processes are an emerging technology. Their use promises low-stress assembly of components while improving the thermal contact and reducing the thermal resistance. Nanostructured surface modifications can significantly enhance adhesion and reliability of joints between different materials. This work examines reactive multilayer of nickel and aluminum, directly sputtered on nanostructured black silicon surfaces and compares their phase transformation with reference samples deposited on pristine silicon surface. The investigation of the quenched self-propagating reaction reveals a clear influence of the nanostructured surface on the prolongation of the phase transition. Rapid thermal annealing tests result in the formation of Al_1.1Ni_0.9 phase. The nanostructured interface seems to hinder the full transformation of the parent material. The surface modification improves the adhesion of the formed alloy on silicon surfaces and can possibly increase the reliability of joints based on reactive aluminum/nickel multilayer. The use of black silicon, a nanostructured surface modification, is thus a promising approach to realize reliable multi-material joints in complex systems.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

The effects of heating rate before solution treatment and cooling rate after solution treatment on the morphological distribution and evolution of precipitation phase of nickel-based single crystal superalloy were studied. The dissolution, precipitation and growth of precipitation phase and matrix phase during heat treatment were analyzed by means of high power scanning electron microscopy. The results show that the morphology of precipitated phase has nothing to do with the distribution of precipitated phase and the heating rate in the heating process, but the cooling rate in the cooling process affects the shape, size and distribution of precipitated phase. The faster the cooling rate, the smaller the precipitated phase is, the more irregular the shape is, the smaller the equivalent edge length is, and the smaller the channel width of matrix phase is.

Cationised hemp cellulose was prepared by etherification with two quaternary ammonium salts: 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CHPTAC) and glycidyltrimethylammonium chloride (GTMAC) and examined for (i) the efficiency of Cr(VI) removal under acid mine-drainage (AMD) conditions, and (ii) antibacterial activity. Adsorbents were characterised by electron microscopy, Fourier transform infrared (FTIR), CP-MAS ¹³C nuclear magnetic resonance (NMR) spectroscopy, elemental composition and surface charge. FTIR and solid state ¹³C NMR confirmed the introduction of quaternary ammonium moieties on cellulose. ¹³C NMR also showed that cationisation decreased the degree of crystallisation and lateral dimensions of cellulose fibrils. Nevertheless, 47 % - 72% of Cr(VI) ions were removed from solutions at pH 4, by 0.1 g of CHPTAC and GTMAC-cationised cellulose, respectively. Adsorption kinetics followed the pseudo-second order model and isotherms were best described by the Freundlich and Dubinin-Radushkevich models. When GTMAC-modified cellulose was applied to AMD contaminated water (pH 2.7), however, Cr(VI) uptake removal decreased to 22% likely due to competition from Al and Fe ions. Nevertheless, cationised materials displayed considerable antibacterial effects, reducing the viability of Escherichia coli by up to 45 % after just 3 hours of exposure. Together, these results suggest that cationised cellulose can be applied in the treatment of Cr(VI)-contaminated mine water particularly if pre-treatments to reduce Fe and Al concentrations are applied.

Immobilized metal affinity chromatography (IMAC) is a popular and valuable method for the affinity purification of polyhistidine-tagged recombinant proteins. However, it often shows practical limitations, which might require cumbersome optimizations, additional polishing, and enrichment steps. Here, we present functionalized corundum particles for the efficient, economical, and fast purification of recombinant proteins in a column-free format. The corundum surface is first derivatized with the amino silane APTES, then EDTA dianhydride, and subsequently loaded with nickel ions. The Kaiser test, well-known in solid-phase peptide synthesis, was used to monitor amino silanization and the reaction with EDTA dianhydride. In addition, ICP-MS was performed to quantify the metal-binding capacity. His-tagged protein A/G (PAG), mixed with bovine serum albumin (BSA), was used as a test system. The PAG binding capacity was around 3 mg protein per gram of corundum. Cytoplasm obtained from different E. coli strains was examined as an example of a complex matrix. The imidazole concentration was varied in the loading and washing buffers. As expected, higher imidazole concentrations during loading are usually beneficial when higher purities are desired. Even when higher sample volumes, such as one liter, were used, recombinant protein down to a concentration of 1 µg/mL could be isolated selectively. Comparing the corundum material with standard Ni-NTA agarose beads indicated higher purities of proteins isolated using corundum. His6-MBP-mSA2, a fusion protein consisting of monomeric streptavidin and maltose-binding protein in the cytoplasm of E. coli, was purified successfully. To show that this method is also suitable for mammalian cell culture supernatants, purification of the SARS-CoV-2-S-RBD His8 expressed in human Expi293F cells was performed. The material cost of the nickel-loaded corundum material (without regeneration) is estimated to be less than 30 cents for 1 gram of functionalized support or 10 cents per milligram of isolated protein. Another advantage of the novel system is the corundum particles' extremely high physical and chemical stability. The new material should be applicable in small laboratories and large-scale industrial applications. In summary, we could show that this new material is an efficient, robust, and cost-effective purification platform for the purification of His-tagged proteins, even in challenging, complex matrices and large sample volumes of low product concentration.

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

The selective extraction of metals from aqueous solutions is very important stage in hydrometallurgical processing of metallic waste. Leach solutions are usually a multi-component mixture. The main impurity of aqueous solutions obtained after leaching using inorganic acids is iron. In this work, the membrane separation of iron(III) from nickel(II), cobalt(II) and lithium(II) was studied. The facilitated transport of metal ion using the polymer inclusion membranes (PIMs) with tetrabutylammonium bromide (TBAB) as an ion carrier under various conditions was analyzed in detail. The several factors such as the ion carrier concentration in the membrane as well as the effect of the inorganic acids concentration in the source/receiving phases on the kinetic parameters were investigated. The results show that ionic liquid TBAB is a very selective ion carrier of Fe(III) towards Ni(II), Co(II) and Li(I) .

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

Nutrition, diabetes, and mental disorders are interconnected and significantly impact an individual's overall health and well-being. This comprehensive review aims to explore the complex interplay between nutrition, diabetes, and mental disorders, highlighting the latest research findings in this field. While the influence of nutrition on the development and management of both diabetes and mental disorders is widely recognized, there remains a gap in understanding the intricate interplay between nutrition, mental health, and diabetes. Diabetes is associated with an increased risk of mental disorders, including depression, anxiety, and cognitive decline. Mental disorders can also contribute to the development of diabetes through various mechanisms including increased stress, poor self-care behaviors, and adverse effects on glucose metabolism. Thus, the mechanisms linking nutrition, diabetes, and mental disorders are complex and multi-factorial. Inflammation, oxidative stress, gut microbiota alterations, and neuroendocrine dysregulation have emerged as potential pathways that may mediate the relationship between nutrition, diabetes, and mental disorders. Additionally, deficiencies in essential nutrients such as omega-3 fatty acids, vitamin D, B vitamins, zinc, chromium, magnesium, and selenium have been implicated in the pathogenesis of both diabetes and mental disorders. Our findings indicate that the use of personalized dietary interventions and targeted nutrient supplementation can improve metabolic and mental health outcomes in patients with type 2 diabetes.