We present a generalized state-space model formulation particularly motivated by an online scheduling perspective. Through these proposed generalizations, we enable a natural way to handle routinely encountered disturbances and a rich set of corresponding counter-decisions. Thereby, greatly simplifying and extending the possible application of mathematical programming based online scheduling solutions to diverse application settings.

Background: Nowadays vital signs in clinics are electronically monitored excepted for urine output which still requires, manual recording, which is subject to human errors. We, in-vitro, assessed in this study the ability a novel electronic device to measure by a combination of two different methods, the real time flow-output, like urine output. Methods: Flow or urine output was measured by a combination technique of gravimetry using a dynamometer and capacitive sensing to improve precision. Data were obtained in 3 different situations, low, medium, and high flow. Results: Three different situations were tested: full or empty dead space and Pasteur’s chamber. The differences between the injected and measured volume varies from 0 to 5 ml representing a maximal error of 3 % regardless of the volume injected and the flow in ml/hour. The capacitive sensors behave as expected with a parallel curve of the expected and measured flow. Conclusion: We have shown in this in-vitro study that the combination of gravimetry and capacitive sensors analysis allow accurate measurement of volume and flow-output. Clinical trials should be conducted to confirm its usefulness in urine output measurement in the real life.

Soil moisture can be an important indicator of climate change in humid and semi-arid areas. This indicator can more efficiently propose different public policies related to climate change than just using precipitation and temperature data. Given the above, the objective of this study is to evaluate changes in soil moisture in the state of Pernambuco during the period 1961-2021, using the System of Hydrological Response Units for Pernambuco. In this study, two river basins in the state of Pernambuco that represent the different climatic conditions of the state will be chosen. The results show that in the coastal region, there is a tendency towards more saturated soils, and in the semi-arid region, there is a tendency towards drier soils. With these results, it is possible to conclude that public policy decisions for the economy, environment, and society must consider this vital water balance variable.

In cutting processes tool condition affects the quality of the manufactured parts. As such an essential component to prevent unplanned downtime and to assure machining quality is having information about the state of the cutting tool. The primary function of it is to alert the operator that the tool has reached or is reaching a level of ware beyond which behavior is unreliable. In this paper the tool condition is being monitored by analyzing the electric current on the main spindle via an artificial intelligence model utilizing a LSTM neural network. In the current study the tool is monitored while working on a cylindrical raw piece made of AA6013 aluminum alloy with a custom polycrystalline diamond tool, for the purposes of monitoring the ware of these tools. Spindle current characteristics were obtained using external measuring equipment to not influence the operation of the machine included in a larger production line. As a novel approach, an artificial intelligence model based on a LSTM neural network is utilized for the analysis of the spindle current obtained during a manufacturing cycle and assessing the tool ware range in real time. The neural network was designed and trained to notice significant char-acteristics of the captured current signal. The conducted research serves as a proof of concept for use of a LSTM neural network-based model as a method of monitoring the condition of cutting tools.

The research aimed at the ecological assessment of the environment around uranium mining enterprises in the Turkestan region. The authors examined the state of the soil and vegetation for 2021-2023, their chemical composition and the effects of radiation. Excesses of background radiation were detected by alpha and beta studies. To study the structural organization of plant communities, we conducted floristic studies in the areas immediately adjacent to NAC “Kazatomprom” enterprises. The general habitus, size, number and shape of vegetative parts of plants were taken into account as comparison parameters. The flora growing in the study areas of the Suzak district of the region, which is distinguished by its uniqueness and narrow relevance to the ecological conditions of the area, was taken as biological objects of study. To determine the ecological state of the adjacent territories of NAC “Kazatomprom” and for physical, chemical and taxonomic analyses, 78 soil samples and 37 plant samples were obtained. The studied samples were taken near settlements N, B and S, which are closest to the territories of NAC “Kazatomprom”.

Respiratory allergic diseases, affect over 500 million people globally and pose a substantial burden in terms of morbidity, mortality, and healthcare costs. Restrictive factors such as geographical disparities, infectious pandemics, limitations in resource, and shortage of allergy specialists in underserved areas, impede effective management. Moreover, the well-established suboptimal adherence in patients with respiratory allergies, contribute further to the accelerated loss of disease control. Telemedicine encompasses real-time visits, store-and-forward options triage, and computer-based technologies for establishing and efficient doctor-patient communication. Recent advances in digital technology, including designated applications, informative materials, digital examination devices, wearables, digital inhalers, and integrated platforms, facilitate personalized and evidence-based care delivery. The integration of telemonitoring in respiratory allergy care has shown beneficial effects in disease control, adherence, and quality of life. While the COVID-19 pandemic accelerated the adoption of telemedicine, certain concerns regarding technical requirements, platform quality, safety, reimbursement, and regulatory considerations remain unresolved. Challenges in telemonitoring implementation further include ensuring effective doctor-patient collaboration, addressing privacy concerns, and establishing cost-effective models. The integration of artificial intelligence (AI) in telemonitoring applications holds promise for data analysis, pattern recognition, and personalized treatment plans. Striking the balance between AI-enabled insights and human expertise is crucial for optimizing the benefits of telemonitoring. This overview reports the up- to- date telemedicine approaches in managing patients with respiratory allergies. While telemonitoring exhibits potential in enhancing patient care and healthcare delivery, critical considerations have to be addressed in order to ensure the successful integration of telemonitoring into the healthcare landscape.

A temporary monitoring system was installed on the 175-years-old historical Széchenyi chain bridge under its reconstruction process. The bridge is in the downtown area of the capital city of Hungary and plays a significant role in city life of Budapest. Six-month-long measurements were conducted during the reconstruction process of the bridge, yielding crucial insights into the structural behaviour of the historical structure. Measurement results were evaluated; the findings encompass the rotation capacity of pins between chain elements, and structural response to temperature changes. This information helped the decision-making of designers and construction company during the reconstruction made between 2021 and 2023. For instance, daily temperature fluctuations result in increased bending moments in the chain elements, rising up to 158% compared to the values observed during a proof load test in 2018. Furthermore, the measurements reveal an approximate 42% increase in normal forces compared to the proof load test, which highlights the high sensitivity of chain bridges to temperature fluctuations, where geometric stiffness plays a crucial role. Reconstruction, reducing self-weight, notably intensifies the impact on normal forces and bending moments. These outcomes strongly emphasize the dominance of dead load and self-weight in the case of chain bridges.

Road pavement monitoring represents the baseline to the pavement maintenance process. To quickly fix a damaged road, relevant authorities need a high-efficiency methodology that allows them to obtain data describing the current conditions of a network of roads. In urban areas, large-scale monitoring campaigns may be more expensive and not fast enough to describe how pavement degradation has evolved over time. Furthermore, at low speeds, many technologies are inadequate for monitoring the streets. In such a context, employing black box equipped vehicles to perform a routine inspection could be an excellent starting point. However, the vibration-based methodologies used to detect road anomalies are strongly affected by the speed of these vehicles. In this study, a statistical method was to analyze the effects of speed on road pavement conditions at different severity levels through the data recorded by taxi vehicles. Likewise introduced was a process that overcomes the speed effect when considering road surface conditions. The methodology proposed has succeeded in predicting the right damage severity level based on only two recorded parameters: speed and pavement deterioration index.

This observational pilot study aimed to investigate continuous glucose monitoring (CGM) metrics in older Japanese patients with type 2 diabetes mellitus (T2DM) using a continuous glucose monitoring system (FreeStyle Libre Pro) for CGM during the first tirzepatide administration and compared the glycemic control measures before and after the treatment. The four patients re-ported a mean age of 79.5 years (standard deviation [SD]: 5.8), mean body mass index of 24.63 kg/m2 (SD: 4.7), and mean glycated hemoglobin level of 9.1% (SD: 2.1). After tirzepatide treatment, the mean of time in range, time above range, and time below range changed from 53.2% to 78.9% (p = 0.041), 45.8% to 19.7% (p = 0.038), and 1.0% to 1.5% (p = 0.206), respectively. Improved hy-perglycemia reduced the oral glucose medication in two cases and decreased the frequency of insulin injections in two cases. All cases demonstrated the CGM index improvement during short-term observation despite some differences. Future studies need to investigate the long-term impact on functional prognosis, safety, and tolerability, especially in nonobese older Asian pa-tients, to elucidate the potential benefits of tirzepatide. However, tirzepatide-associated robust glycemic improvement may simplify and reduce diabetes treatment-associated complication in older patients with T2DM.

The previous studies on the diversion pipe of pumped storage power stations (PSPS) primarily focused on numerical simulations of pulsating pressure propagation within the pipe and its inducing factors. However, there was a lack of field monitoring and analysis of measured data to support surface ambient vibration, resulting in insufficient credibility and practicality of the numerical results. Based on ambient monitoring and data analysis, this paper examines the factors contributing to the ambient vibration of the water diversion pipeline in Changlongshan (CLS) PSPS. It is concluded that: (1) The primary source of vibration originates from units operation-induced ambient vibrations; (2) Vibration during pumping conditions exceeds that during power generation conditions; (3) The ground measuring point's vibration acceleration primarily depends on the distance from the vibration source; (4) Different types of units have varying effects on water diversion pipeline vibrations.

The Internet of Things (IoT) is experiencing exponential growth, revolutionizing various industries with its ability to connect devices and enable advanced applications. In the realm of energy production, IoT offers significant potential for optimizing processes and improving efficiency. This study presents a comprehensive monitoring and energy management strategy for the University of Cuenca's microgrid photovoltaic (PV) system, utilizing IoT and ThingSpeak as key technologies. The proposed strategy leverages intelligent environments and utilizes ThingSpeak as a robust platform for data presentation and analysis. By integrating IoT devices and sensors, real-time monitoring of PV system parameters such as solar radiation and temperature is achieved. The collected data is then analyzed using advanced algorithms and visualized through ThingSpeak, enabling effective energy management and decision-making. The developed monitoring system was rigorously tested in a laboratory microgrid setting, where the PV system is interconnected with other generation and storage systems, as well as the electrical grid. Through the seamless integration of these components, the monitoring system provides enhanced visibility and control over the microgrid's energy production. The results demonstrate the successful implementation of the monitoring system, showcasing its ability to improve the supervision, automation, and analysis of daily energy production. By leveraging IoT technologies and ThingSpeak, stakeholders can access real-time data, analyze performance trends, and optimize energy resources.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

Effective management of retinoblastoma (RB), the most prevalent childhood eye cancer, depends on reliable monitoring and diagnosis. A promising candidate in this context is the secreted trefoil family factor peptide 1 (TFF1), recently discovered as a promising new biomarker in patients with a more advanced subtype of retinoblastoma. The present study investigated TFF1 expression within aqueous humor (AH) of enucleated eyes and compared TFF1 levels in AH and corresponding blood serum samples from RB patients undergoing intravitreal chemotherapy (IVC). TFF1 was consistently detectable in AH, confirming its potential as a biomarker. Crucially, our data confirmed that TFF1 secreting cells within the tumor mass originate from RB tumor cells, not from surrounding stromal cells. IVC therapy responsive patients exhibited remarkably reduced TFF1 levels post-therapy. By contrast, RB patients` blood serum displayed low to undetectable levels of TFF1 even after sample concentration and no therapy-dependent changes were observed. Our findings suggest that compared to blood serum AH represents the more reliable source for TFF1 if used for liquid biopsy RB marker analysis in RB patients. Thus, analysis of TFF1 in AH of RB patients potentially provides a minimal invasive tool for monitoring RB therapy efficacy, suggesting its importance for effective treatment regimens.

Aim was to develop a population pharmacokinetic model for methotrexate (MTX) during high-dose treatment (HDMTX) in pediatric patients with acute lymphoblastic leukemia (ALL) and non-Hodgkin’s lymphoma (NHL) and to describe the sources of variability. The study included 50 patients (1-18 years) who received 3 or 5 g/m2 of HDMTX. Nonlinear mixed effects modeling approach was applied for data analysis. Parameter estimation was performed by FOCEI, whereas stepwise covariate modeling was used to assess variability factors. The final two-compartment model incorporates the effect of body weight using allometric scaling and the influence of hemoglobin and serum creatinine on MTX clearance (CL). Population pharmacokinetic values for a typical 70 kg subject were: 11 L/h for clearance (CL), 46.5 L and 16.4 L for volume of central (V1) and peripheral compartment (V2), respectively, and 0.168 L/h for intercompartmental clearance (Q). According to the final model, MTX CL decreases with increasing serum creatinine, whereas a positive effect was captured for hemoglobin. A difference of almost 30% in MTX CL was observed among patients’ hemoglobin values reported in the study. In addition to renal function and body weight, it describes the influence of hemoglobin on CL, allowing better understanding of its contribution to HDMTX disposition.

Agricultural soils serve as crucial storage sites for soil organic carbon (SOC). Their appropriate management is pivotal for mitigating climate change. To evaluate spatial and temporal changes in SOC within agricultural fields, continuous monitoring is imperative. In-field data sets of Vis-NIR soil spectra were collected on a long-term experimental site using an on-the-go spectrophotometer. Data processing for continuous SOC prediction involves a two-steps modelling approach. In Step 1, a Partial Least Square (PLSR) regression model is trained to establish a relationship between the SOC content and the spectral information also including spectral preprocesisng. In Step 2, the predicted SOC content obtained from the PLSR models is interpolated using ordinary kriging. Among the tested spectral preprocessing techniques and semivariogram models, SG and gapDer preprocessing along with a Gaussian semivariogram model, yielded the best performance resulting in a root mean square error of of 1.24 and 1.26 g kg-1. A striping effect due to the transect-based data collection was addressed by testing the effectiveness of extending the spatial separation distance, employing data aggregation, and defining the distribution based on treatment plots using block kriging. Overall, the results highlight the immense potential of on-the-go spectral Vis-NIR data for field-scale spatial-temporal monitoring of SOC.

High efficiency and safety are critical factors in ensuring optimal performance and reliability of systems and equipment across various industries. Fault Monitoring (FM) techniques play a pivotal role in this regard by continuously monitoring system performance and identifying the presence of faults or abnormalities. However, traditional FM methods face limitations in fully capturing the complex interactions within a system and providing real-time monitoring capabilities. To overcome these challenges, Digital Twin (DT) technology has emerged as a promising solution to enhance existing FM practices. By creating a virtual replica or digital copy of a physical equipment or system, DT offers the potential to revolutionize fault monitoring approaches. This paper aims to explore and discuss the diverse range of predictive methods utilized in DT and their implementations in FM across industries. Furthermore, it will showcase successful implementations of DT in FM across a wide array of industries, including manufacturing, energy, transportation, and healthcare The utilization of DT in FM enables a comprehensive understanding of system behavior and performance by leveraging real-time data, advanced analytics, and machine learning algorithms. By integrating physical and virtual components, DT facilitates the monitoring and prediction of faults, providing valuable insights into the system’s health and enabling proactive maintenance and decision-making.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton com-munities but different detection approaches are biased uniquely. Genetic identification of marine plankton has become standard but is still not used in routine monitoring. This study assessed the diversity of plankton taxa using 18S high throughput sequencing from 2011-2012 from small-volume (~200ml) samples from the Water and Microplankton Sampler (WaMS) deployed on the Continuous Plankton Recorder platform (CPR). The 18S-HTS survey revealed a bias towards heterotrophic taxa, and phototrophs under 10µm within the photosynthetic community. In comparison with phytoplankton microscopic counts from the CPR survey and Western Channel Observatory station L4, only 8-12 taxonomic families were common to all three surveys, with a bias towards larger diatoms and dinoflagellate taxa in microscopy surveys. The WaMS survey detected a contrasting but complementary taxa set to that of microscopic surveys. Additional Quantitative PCR was carried out on the picoeukaryotic pelagophyte, Aureococcus anophagefferens, and the nanoeukaryotic potential harmful algae, Pseudo-nitzschia delicatissima, from 2011-2013. This confirmed the persistence presence of A. anophagefferens in the Western Channel and an elevated abundance of both species in 2011. Species specific seasonality were distinct from those of aggregrate phytoplankton groups.

Background/Objectives: The purpose of the proposed study is disclosure of correlations between the dynamics of the Breathe Rate (BR) and Heart Rate (HR) when performing the intermittent physical operation at maximum power on a cycle ergometer.Methods: The stage on the study of the General functional athlete readiness (GFAR) performed using the sports standard “Red Engine” and the cycle ergometer in 16 volunteers (10 men, 6 women) whose average age was 21±1.17 years. To determine the sports potential of the volunteers in this study, we used own Coefficient of Anaerobic Capacity (CANAC Q, beats). Continuous recording of the heart rate and respiratory rate of volunteers in the maximum power sports test was carried out by the “RheoCardioMonitor” device with an athlete functional readiness module based on the method of Transthoracic electrical impedance rheography (TEIRG).Results: The degree of correlation of functional indicators (M, HR_M, GFAR) with CANAC Q for the group in full (n=80) occurred at a very high level, which confirmed the effectiveness of using the Coefficient of Anaerobic Capacity (CANAC Q) in assessing the general functional athlete readiness of the volunteers. Conclusions: CANAC Q measured in “beats” of the heart and recorded very accurately using the method of transthoracic electrical impedance rheography (TEIRG). For this reason as promising sports PSM-system, CANAC Q can replace the methods for determining the functional athlete readiness by blood lactate concentration and maximum oxygen consumption.

Drought is considered one of the severest natural disasters and it is difficult to predict it. This review article aimed to display the state of the art of methods used to predict and monitor types of droughts. We examine more than 30 indices and models to identify the strengths and weaknesses of methods and identify gaps remaining in this field. Examples of examined indies are Palmer Drought Severity Index (PDSI), Standardized Precipitation Index (SPI), and Standardized Precipitation Evapotranspiration Index (SPEI). The research found improvement in drought modeling, however, more focus and improvement are required to monitor and predict drought types. It also found that some methods outperform others such as PDSI, SPI, SPEI, EVI, NDVI, NDWI, VCI and TCI.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton communities but is biased towards those organisms that can be distinguished using the microscope. Genetic identification of marine plankton has become standard but is still not used. This study is a comprehensive study genetically measured taxa in the Western Channel of UK using a small-volume automated water sampler deployed on the CPR platform. The study present one year of high-throughput sequencing data focussing on smaller plankton and separate community to that measured by microscopy that can complement each other for a holistic view of plankton. Quantitative tests of two harmful algae show relatively high abundance of the Pelagophyte Aureococcus anophagefferens during 2011 with low nitrite levels. Three years of Pseudo-nitzschia delicatissima quantitative monitoring also shows a greater abundance of this potentially harmful taxa in 2011. Flow cytometry reveals distinct seasonal cycles with distinct timings.

Abstract: Background: Stunting is primarily a public health concern in LMIC. The involvement of Integrated Service Post cadres is one of the strategies to combat stunting in Indonesia. Objective: This study aimed to determine the effect of a short course on cadres knowledge. Method: A single group pre-post test design was conducted in Yogyakarta, Indonesia, from March to May 2022. Thirty cadres were selected based on the following criteria: willingness to participate, the number of stunted children in their Integrated Service Post (Posyandu), and full attendance at short course. The knowledge scores were measured by a structured questionnaire after short course (post-test 1) and 4 weeks later (post-test 2). We apply STATA 16 to calculate the mean difference (MD) using a t-test and Generalized Estimated Equation (GEE). Furthermore, the adequacy of the short course was evaluated with in-depth interviews. Result: On post-tests 1 and 2, cadres' knowledge of IYCF, children growth monitoring (CGM) and children development monitoring (CDM) significantly improved. The GEE analysis showed that a short course significantly improves cadres' knowledge after age control, education, occupation, and years of experience. Conclusion: Short course in-creased their affection, self-efficacy, and confidence, hence, they are capable of assisting children through home visits.

Accurately monitoring insecticide resistance in target mosquito populations is important to combating malaria and other vector-borne diseases, and robust methods are key. The “WHO susceptibility bioassay” has been used for +60 years: mosquitoes of known physiological status are exposed to a discriminating concentration of insecticide. Several changes to the test procedures have been made historically which may seem minor but could impact bioassay results. The published test procedures and literature for this method were reviewed for methodological details. Areas where there was room for interpretation in the test procedures or where the test procedures were not being followed were assessed experimentally for impact on bioassay results: covering or uncovering of the tube end during exposure, number of mosquitoes per test unit, and mosquito age. Many publications do not cite the most recent test procedures, methodological details are reported which contradict the test procedures referenced or methodological details are not fully reported. As a result, the precise methodology is unclear. Experimental testing showed that using fewer than the recommended 15-30 mosquitoes per test unit significantly reduced mortality, covering the exposure tube had no effect, and using mosquitoes older than 2-5 days old increased mortality, particularly in the resistant strain. Recommendations are made for better reporting of experimental parameters.

Abstract: The Hanqu Joint Station of the Dingbian Oil Production Plant of Yanchang Oilfield Co., Ltd is located at the edge of the desert in northern China. the bad field conditions and strong sandstorm, the hardware of computer monitoring system of Joint Station is often damaged. At the same time, the core equipment of the joint station three-phase separator oil chamber liquid level is hard to achieve high precision constant value control, the general control algorithm is difficult to meet the control requirements.This paper proposed a design scheme of a oilfield joint station computer monitoring system based on the Siemens S7-300 PLC, the hardware of the monitoring system adopts the redundancy scheme of dual monitoring computers, dual programmable logic controllers (PLCs), and dual industrial Ethernet. The BP neural network PID control algorithm was used to realize constant value control of the oil chamber liquid level of the three-phase separator of the core equipment of the joint station，and realized high control precision. The monitoring system could well adapt to the harsh environment of the scene, and showed high reliability and efficiency.

As the number of legal and illegal mining sites increase, integrative methods to evaluate the effects of mining pollution on Andes-Amazonia freshwater ecosystems are paramount. Here, we sampled water and sediments in 11 sites potentially affected by mining activities in the Napo province (Ecuador). The environmental impacts were evaluated using four lines of evidence (LOEs): water physico-chemical parameters; metal exposure concentrations; macroinvertebrate community response (AAMBI); and toxicity by conducting bioassays with Lactuca sativa and Daphnia magna. Overall, dissolved oxygen and total suspended solids were, under (<80%) and above (>130 mg/Ls) quality standards. Ag, Al, As, Cd, Cu, Fe, Mn, Pb and Zn in water and V, B and Cr in sediments were detected above quality standards. Nine out of eleven sites were classified as having bad environmental quality based on the AAMBI. Ranges of L. sativa seed germination in both water (37% to 70%) and sediment (0% to 65%), indicate significant toxicity. In 5 sites, neonates of D. magna showed a 25% reduction in survival compared to the control. Our integrated LOEs index ranked sites regarding their environmental degradation. Given the importance of the Andes-Amazon region, we recommend environmental impact monitoring of the mining expansion using multiple LOEs.

There are numerous challenges involved in the diagnosis and treatment of lung cancer. Globally, majority of people suffers from cancerous disease involving throat cancer, lung cancer, stomach cancer, cancerous brain tumor. Among these the most common ones is the lung cancer or lung carcinoma. The leading cause of the lung cancer is the smoking. Around 80% to 90% of deaths are caused due to Non-small cell lung cancer (NSCLC). The inadequate diagnostic techniques and low chances for the survival of lung cancer patients results from the lack of an early prognosis and incompetency in traditional therapies. However, such challenges involved in the prognosis and treatment of lung cancer are on decline with the progression in magnetic nanoparticle (MNP) technology. Many break-through discoveries and inventions have been made in the field of cancer therapy by using magnetic nanoparticles. The implication of nanotechnology has led to the recent advancement in nanomedicine field. This has encouraged the improvement in different therapeutic and diagnosis strategies employing nanotechnology. The generation of immense technological benefits for nanoparticles systems has been accredited to its remarkable nanoscale physico-chemical properties. This in turns provides the early detection of lung cancer and active drugs delivery for an improved theranostics strategy. The present review provides a general idea of the current progression in the therapeutic and prognosis purpose of magnetic nanoparticles. Further, we disclose the development in the lung cancer theranostics by functionalization of magnetic nanoparticles. The established importance of magnetic nanoparticles in the theranostics centers for lung cancer has been revealed in this paper. The challenges existing in the theranostics of lung cancer are addressed through the functioning of magnetic nanoparticles in the process.

Pathogens and adulterants in human feeding consumables can be readily identified according to their electrical properties. Electrical bioimpedance analysis (BIA) has been widely used for body contents characterization, such as blood, urine, lactate and sweat. If the blood glucose concentration alters the electrical properties of the blood medium, then the impedance spectrum obtained by BIA can be used to measure glycemia. In some applications, artificial neural networks allows the correlation of these parameters (impedance and glucose concentration) by means of symbolic and statistical rules. According to our literature review, there is any physical model that allows the interpretation of the relationship between blood’s electrical properties, obtained by BIA, and the concentration of glucose in the blood plasma. This article proposes a simplified physical model for blood electrical conductivity as a function of glucose concentration, based on Bruggeman’s effective medium theory. The equations of this model were obtained considering an insulating phase distribution diffused in a conductive matrix, in which red blood cells are represented by macroscopic insulating nuclei and glucose molecules by microscopic insulating particles. The impedance spectrum for different glucose concentrations (4.0 to 6.8 mmol/L) in a blood sample, published by Kamat Bagul (2014), were compared with the proposed model. The results showed a significant correlation with the experimental data, showing a maximum error of 5.2%. The proposed model might be useful in the design of noninvasive blood glucose monitoring systems.

Objectives: To investigate the value of early lactate dynamic monitoring index in predicting prognosis of patients with sepsis and septic shock. Methods: We performed our test on 50 patients. Out of 50 patients, 28 are male, and 22 are female. Prospectively studied pediatric patients with septic shock were performed. Vital signs, Lactate clearance, were obtained at presentation 6 h, 12 h, 24 h over the first 48 h of hospitalization. The therapy received, outcome parameters of mortality and duration of hospitalization were recorded. Results: The statistical data and comparative analysis showed that an average of 16.88 days after admission, 5 patients have died, 17 patients are poorly prognosis leaves the hospital, and the remaining 28 are recovered and discharged. The primary outcome variable of mean 16 days hospitalization mortality rate was 10%. Poor prognosis 34% and fully recovery 56 % were observed. In this retrospective cohort study, a lactate level of more than 2.5mmol/L was the best threshold to predict 28-day mortality among severe sepsis and septic shock patients. In our research, we found mean LC 6 h 3.08mmol/L, and after 48 h mean it is 1.79mmol/L. Significant LC 6 h found, which is 8.08mmol/L in the death group patient where 48 h mmol/L shows significant high. Poor prognosis also presents a clinical increase of lactate level high in the LC 6 h analysis, which is 3.32mmol/L. Recovered patients showed a significant improvement after administering treatment depending on the patient organ involvement and good decrease of lactate reports achieved, which is 1.20mmol/L, where admission reports show it was 1.91mmol/L in LC 6 h. Mean Heart rate 94/51mmhg, pulse 119, temperature 39℃, respiratory rate 32.26, and urine output 456 ml recorded during our study. Death patient shows a remarkable detonation of those reports but has a significant clinical report with the recovered patients. Conclusion: The early lactate dynamic monitoring index has a high value in predicting sepsis and septic shock patients' prognosis, thus worth popularizing.

The paper presents a case study and a model for condition monitoring of Diesel engines’ oil of urban buses, through the accompaniment of the evolution of its degradation, with the objective to implement a predictive maintenance policy. Along time, because the usage, there is some decay in the lubricant properties. However, in normal functioning conditions, the lubricants properties, at the time the manufacturers recommend its changing, regardless of they are within the safety limits. Then, based on the accompaniment of the lubricants’ oil condition, the intervals of oil replacement can be enlarged what implies the availability increasing and the corresponding production increasing of the equipment. The model presented in this paper shows its potential to be spread to other types of equipment and organisations that want can implement similar maintenance policies, to achieve the best availability based on the real equipment health conditioning conditions

Multi-view stereo (MVS) employs multi-point photography for image point positioning and three-dimensional reconstruction technology. Recently, this technology has been introduced into the monitoring of road slopes due to advances in photography and computing technology. In general, the various phases of post-image processing procedures are applied to various photographic data. In this study a novel, automated image-monitoring system is proposed to improve the ability of automatic processing. First, an Internet of things (IoT)-based digital photography system architecture was constructed to provide automatic control of camera photography and real-time transmission of image data. In addition, a visual SfM-MVS 3D reconstruction technique was used to develop related software and hardware interfaces based on the built-in Python computing framework of Photoscan Pro. The software integrates fully automatic photography, image transmission, monitoring of data processing and product release programs. The experimental results show that the system architecture can be applied to fully automatic three-dimensional monitoring of road slopes.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

This paper present a platform for airborne sensor applications using low-cost, open-source components carried by an easy-to-fly unmanned aircraft vehicle (UAV). The system, available in open-source [1], is designed for researchers, students and makers for a broad range of their exploration and data-collection needs. The main contribution is the extensible architecture for modularized airborne sensor deployment and real-time data visualisation. Our open-source Android application provides data collection, flight path definition and map tools. Total cost of the system is below 800 dollars. The flexibility of the system are illustrated by mapping the location of Bluetooth beacons (iBeacons) on a ground field and by measuring water temperatures in a lake.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

We used light, electron microscope and teased fiber autoradiography to show that myelinating Schwann cells synthesize phospholipids and proteins in perinuclear cytoplasm and superficial cytoplasmic channels or Cajal bands (SCC/CB). Neither phospholipid nor protein syntheses occur in paranodal loops, Schmidt-Lanterman incisures or adaxonal cytoplasm. Autoradiographic studies also show that in support of local protein synthesis, RNAs move from the nucleus into perinuclear cytoplasm and out along SCC/CB. Unlike other phospholipids, phosphatidylinositol synthesis occurs extensively in axons. This finding indicates differences in the distributions of phospholipid synthesizing enzymes in smooth endoplasmic reticulum of Schwann cell processes and axoplasm.Autoradiographs of nerves at longer survival times show that tritiated phosphatidylcholine and fucose-labeled glycoproteins move from synthetic sites to outermost myelin lamellae. From there, phosphatidylcholine spreads inward reaching innermost lamellae of thicker sheaths in days. Coupled with retention of fucose glycoproteins in outer myelin lamellae is the presence of fucose glycoprotein synthesized during early myelination in inner lamellae of thicker sheaths, a result consistent with growth of myelin sheaths from inner lamellae out. In this review, we revisit these studies because they provide temporal and spatial perspectives needed in understanding dynamic aspects of myelinogenesis and how myelinating cells respond to injury and from altered gene expression.

This paper explores if plants are capable of responding to human movement by changes in their electrical signals. Towards that goal we conducted a series of experiments, where humans over a period of 6 months were performing different types of eurythmic gestures in proximity of garden plants, namely salad, basil, and tomatoes. To measure plant perception, we used the plant spikerbox, a device that measures changes in voltage differentials of plants between roots and leaves. Using machine learning, we find that the voltage differentials over time of the plant predict if (a) eurythmy has been performed, and (b) which kind of eurythmy gestures has been performed. We also find that the signals are different based on the species of the plant. In other words, the perception of a salad, tomato, or basil might differ just as perception of different species of animals differ. This opens new ways of studying plant ecosystems, while also paving the way to use plants as biosensors for analyzing human movement.

ABSTRACT Heavy metals have been classified as dangerous environmental pollutants. Interest in feasible ways to reduce heavy metals pollution is a noble goal. Adsorption is an effective method based on its effectiveness and low- cost. Nowadays, low-cost bio-sorbents have been utilized to replace costly expensive adsorbents. Rich cellulose materials are effective heavy metal adsorbents, and their performance can be enhanced via chemical modification. The present work reviews the steady progress in the utilization of agriculture by-product wastes as heavy metal bio-sorbent. The unique advantages of these by-products such as renewability, abundance, simple processing, and low cost, justifier this work. The results confirm that the chemically treated agro-wastes exhibit high- removal efficiency (reaches 95% in most cases). The adsorption isotherm studies indicate that the concentration of the metal ions has a significant effect on the adsorption process. The Freundlich model provides a physical adsorption model of the metal ions on the bio-sorbent surface. Langmuir isotherm offers an estimate of the effect of different factors on the efficiency of the process. The adsorption kinetics studies offer an idea of reaction pathways including the adsorption mechanism and the efficiency of the metal ion removal. Applying the pseudo-first-order and pseudo-second-order models describes the adsorption kinetics. This information can be utilized in developing effective strategies to remove heavy metal ions using chemically treated agro-waste. The data confirmed that chemical modification is a significant parameter in the efficiency of metal ion removal. The feasibility and effectiveness of using these cellulosic by-products as bio-sorbent should be given attention and encouraged.

Based on the Flashing Ratchet Potential (FRP) and Electro-Spectroscopy detection techniques, a new detection method was experimentally examined. This method allows the detection of sub-micro particles in the human exhaled air such as viral particles and other biological agents. The detection signal created by this method is carried out by electron current buildup forming an Electric Current-Spectrum (ECS) distinguishing the contents of the exhaled air samples. The detection method was developed based on FRP and a beam of free charges passing through the electrodes of the FRP. The ECS is characterized by low-energy free charges interacting with the medium through which they pass, where numerous free charges are scattered (delayed) as a result of these interactions. The resulting ECS is characterized by FRP's capacity to drift back the delayed free charges to their original starting positions. By comparing the ECS of two exhale air samples, this new technology can be utilized to identify the presence of viral and microorganisms’ particles. The time-escalating ECS difference quickly indicates the presence of such particles. Moreover, the FRP's optimal operating settings was experimentally defined, in addition to the experimental evaluation of its functionality to confirm the FRP's promising sensing capabilities, which were statistically examined several times to ensure the reproducibility of the results.

The windowpane oyster Placuna placenta, lives in brackish coastal waters and has long been economically important to the Philippines because of its durable and translucent shell, which is used as a glass substitute and material for making windowpanes and handicrafts. There has been considerable degradation of the windowpane oyster fishery in past decades. Moreover, there are waste and under-exploited by-products such as the meat, which though nutritious and edible, currently has a very low value; its use being confined to dishes consumed by families in the fishing community. Historically there are instances of excellent practice in terms of regulating the windowpane oyster fishery, while in recent times there have been local initiatives to restore this and to develop high value food products from the meat. These initiatives have, however, never been followed through at a provincial or national level. Research on other molluscs and marine organisms highlights that these also contain high value pharmaceutical products. This review compiles evidence to establish the groundwork for an essential and comprehensive multidisciplinary research program centred around the windowpane oyster, which would ensure a high value for all parts of the oyster, including those currently discarded. By fostering a sustainable and circular economy within this fishery sector and its associated industry, its economic value would be amplified. This is particularly important for oyster harvesters in the Philippines, who often find themselves at the economic ladder's lower rungs. By integrating the principles of a circular economy, this initiative would not only aim to uplift the economic prospects of these harvesters but in doing so would drive the restoration of the windowpane oyster to its former range.

: Medical gloves, along with masks and gowns, serve as the initial line of defense against poten-tially infectious microorganisms and hazardous substances in the health sector. During the COVID-19 pandemic, medical gloves played a significant role, as they were widely utilized by society in daily activities as a preventive measure. These products demonstrated their value as important personal protection equipment (PPE) and reaffirmed their relevance as infec-tion-prevention tools. This review describes the evolution of medical gloves since the discovery of vulcanization by Charles Goodyear in 1839, which fostered the development of this industry. Regarding the current market, a comparison of the main properties, benefits, and drawbacks of the most widespread types of sanitary gloves is presented. The most usual gloves are produced from natural rubber (NR), polyisoprene (IR), acrylonitrile butadiene rubber (NBR), polychloroprene (CR), polyethylene (PE), and poly(vinyl chloride) (PVC). Furthermore, the environmental impacts of the conventional natural rubber gloves manufacturing process and mitigation strate-gies, such as bioremediation and rubber recycling, are addressed. In order to create new smart medical gloves with improved properties, several biopolymers (e.g. poly(vinyl alcohol) and starch) and additives such as biodegradable fillers (e.g., cellulose and chitin), reinforcing fillers (e.g. silica and cellulose nanocrystals), and antimicrobial agents (e.g., biguanides and quaternary ammonium salts) have been evaluated. This paper covers these smart materials and describes different innovative prototypes of gloves and coatings designed with them.

Reactive transport (RT) couples bio-geo-chemical reactions and transport. RT is important to understand numerous scientific questions and solve some engineering problems. RT is highly multidisciplinary, which hinders the development of a body of knowledge shared by RT modelers and developers. The goal of this paper is to review the basic conceptual issues shared by all RT problems, so as to facilitate advance along the current frontier: biochemical reactions. To this end, we review the basic equations to point that chemical systems are controlled by the set of equilibrium reactions, which are easy to model, but whose rate is controlled by mixing. Since mixing is not properly represented by the standard advection-dispersion equation (ADE), we conclude that this equation is poor for RT. This leads us to review alternative transport formulations, and the methods to solve RT problems using both the ADE and alternative equations. Since equilibrium is easy, difficulties arise for kinetic reactions, which is especially true for biochemistry, where numerous frontiers are open (how to represent microbial communities, impact of genomics, effect of biofilms on flow and transport, etc.). We conclude with the basic 10 issues that we consider fundamental for any conceptually sound RT effort.

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

Activated carbons can be produced from biomass in a thermal process either in a direct carbonization-activation process or by first carbonizing the biomass and later on activating the biochars into activated carbons. The properties of the ACs are dependent on the type of process used for production. In this study, the properties of activated carbons produced in a one-stage and a two-stage process are considered. Activated carbons were produced by physical activation of two types of starting materials, bio chars produced from spruce and birch chips in a commercial carbonization plant and from the corresponding raw chips. The activated carbons produced were characterized regarding specific surfaces, pore volumes and pore size distributions. The un-activated bio chars had some degree of surface area 190 and 140 m²g^-1 for spruce and birch and pore volumes of 0.067 and 0.092 cm³g^-1. According to the results obtained, two slightly different types of activated carbons are produced depending if a one-stage or a two-stage carbonization and activation process is used. The ACs produced in the one-stage process had higher specific surface areas compared to the ones produced in a two-stage process (761-940 m²g^-1 vs. 540-650 m²g^-1) . In addition, total pore volumes were higher in one-stage process but development of micropores is greater compared to two-stage process. There was no significant difference in total carbon content between one-stage and two-stage process.

Disrupted nutrient recycling is a significant problem for Europe, while phosphorus and nitrogen are wasted instead of being used for plant nutrition. Mineral phosphate is critical raw material, which contains environmentally hazardous elements such as cadmium and uranium. Therefore, phosphorus recovery from agricultural by-product streams is critically important key priority. Phosphorus recovery from food grade animal bone by-products have been applied researched since 2002 with objective driven evolution progress towards specialized pyrolysis processing technology and animal bone char product (ABC) developments in economical industrial scale. Different animal bone by-products tested under different conditions at 400 kg/h throughput capacity in the continuously operated 3R zero emission autothermal carbonization system. The different material core treatment temperatures (between >300°C and <850°C) were combined with different residence times under industrial productive processing conditions. It has been industrial demonstrated that material core treatment temperature <850°C with 20 minutes residence time is necessary to achieve high quality ABC with useful agronomic value. The output ABC product having concentrated >30% phosphorus pentoxide (P2O5) and specific quality innovative fertilizer for agronomical efficient organic and low input farming applications as functional organic fertilizer, soil improver, growing medium and/or fertilizing product blend with high mineral phosphate fertiliser replacement value.

The Fruit Harvest Helper, a mobile application developed by Northwest Nazarene University’s (NNU) Robotics Vision Lab, aims to assist farmers in estimating fruit yield for apple orchards. Currently, farmers manually estimate the fruit yield for an orchard, which is a laborious task. Fruit Harvest Helper seeks to simplify their process. While prior research efforts at NNU concentrated on developing an iOS app for blossom detection, this current research aims to adapt that smart farming application for apple detection across multiple platforms, iOS and Android. The old and new applications were designed with an intuitive user interface that is easy for farmers to use, allowing for quick image selection and processing. Unlike before, the adapted app utilizes a color ratio-based image segmentation algorithm implemented in OpenCV C++ to detect apples in apple tree images selected for processing. The results of testing the algorithm with a dataset of images indicate an 8.52% Mean Absolute Percentage Error (MAPE) and a Pearson correlation coefficient of 0.6 between detected and actual apples on the trees. These findings were obtained by evaluating the images from both the east and west sides of the trees, which was the best method to reduce the error of this algorithm. Although the Fruit Harvest Helper shows promise, there are many opportunities for improvement. These opportunities include exploring alternative machine-learning approaches for apple detection, conducting real-world testing without any human assistance, and expanding the app to detect various types of fruit. The Fruit Harvest Helper mobile application is among the many mobile applications contributing to precision agriculture, nearing readiness for farmers to use in yield monitoring and farm management.

The paper presents the final results from the research project “Urban Abacus of Building Energy performances (Abaco Urbano Energeticodegli Edifci – AUREE)” aimed at supporting the renovation and energy efficiency enhancement of urban building heritage financed by the “Ricerca Sistema Elettrico (MISE) program”. The crux of AUREE project is a Web – GIS GeoBlog portal with customized semantic dashboards aimed at sharing information on urban built environment and promoting the participation of local stakeholders to its improvement. As the latest development of this research, a workflow integrating the AUREE portal with BIM authoring and an open source IoT platform has been implemented and applied to an experimental case study concerning a public building in Carbonia (Italy). The headquarters of the sustainable energy research center Sotacarbo was selected as case study. The presented results proved that it was possible to create an open system, which could be easily consulted by "non-expert" users as well, to make available real-time monitoring data obtained from IoT sensors measuring the energy consumption, the indoor environmental conditions and the usage profiles of public buildings. The proposed open system could also be suitable to be later used as an effective tool to support the rising “energy communities”.

Reducing the carbon footprint of energy production is one of the most pressing challenges facing humanity today. Lignocellulosic biomass residues from fruit production industries show promise as a viable energy source. This paper presents a study of the Italian context concerning the utilization of orchard lignocellulosic residues for energy production as electricity or bioethanol. The potential of various orchard residues was assessed through chemical and physical analysis, and an equivalent electrical energy of about 6441.62 GWh or an amount of 0.48 Mt/y of bioethanol was obtained based on the average annual dry residue mass availability of about 3.04 Mt/y. These data represent the 9.30% of the national electrical energy production from renewable sources, as well as the 6.21% of the Italian demand for gasoline in 2022. Electricity generation from these residues shown its potential as a reliable and sustainable baseload power source, as well as source of renewable transportation fuel. The studied process could be a valuable reference to expand these concepts on global scale to achieve a greener and more sustainable energy future.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Recent development for synthesis of bio-based long chain aliphatic polyesters by acyclic diene metathesis (ADMET) polymerization of α,ω-dienes, derived from plant oils and bio-based chemicals, like bis(10-undecenoate) with isosorbide, using ruthenium-carbene catalysts have been reviewed. Development of subsequent (one-pot) tandem hydrogenation afforded saturated polyesters under mild conditions. The polymerizations under bulk (without solvent, 80-90 ºC) or in ionic liquids (50 ºC) under vacuum conditions enabled synthesis of high molar mass polymers (Mn &gt;30,000 g/mol). The polymerization by molybdenum-alkylidene catalyst afforded the highest molecular weight polyesters (44000‒49400 g/mol, in toluene at 25 ºC) exhibiting promising tensile properties (strength and elongation at break) beyond polyethylene, polypropylene. Depolymerizations of these polyesters including closed loop chemical recycling were also demonstrated. Catalyst developments (more active, under mild conditions) play a key role for the efficient synthesis.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

Introduction: The distribution of typical bacterial redox enzymes such as pyruvate-ferredoxin oxidoreductase (PFOR) in protozoa remains interestingly puzzling. Previous studies have demonstrated diverse cellular localizations of PFOR in amitochondriate anaerobic protozoa such as Trichomonas vaginalis. PFOR is of particular pharmacological importance because it catalyzes the reductive bio-activation of nitro-based prodrugs to cytotoxic radical metabolites. Metronidazole was developed primarily as an antiprotozoal agent against infections caused by T. vaginalis. However, its antimicrobial spectrum was subsequently expanded to cover anaerobic bacterial infections. It has been shown that mutations in the genes encoding PFOR result in inherent resistance of T. vaginalis and anaerobic bacteria to metronidazole. Aims: To analyze the phylogenetic distribution of PFOR in selected protozoa and bacteria using proteins encoded by housekeeping genes as controls. Using comparative bioinformatics to test the hypothesis that PFOR was most likely acquired through horizontal gene transfer from bacteria, proteome-wide analysis and gene expression analysis to identify other genes that were putatively acquired through horizontal gene transfer from bacteria to protozoa. Methods: Sequence similarity queries were performed using the proteins of interest against the NCBI non-redundant protein sequence database with BLASTP version 2.12.0+ from the NCBI website. Multiple sequence alignments were performed with MEGA version X software using the Muscle algorithm. These were then exported in Mega format to construct phylogenetic trees using the neighbor-joining algorithm and the Poisson substitution model. Complete proteomes of representative protozoan and bacterial species were downloaded in fasta format from the ensemblgenomes database. HMM profile libraries were used to screen the proteomes with hmmscan of the HMMer package. Whole proteome BLAST searches were performed between protozoan species of interest against closely related protozoa. The results were compared to the proteome BLAST against the intestinal bacteria Desulfovibrio vulgaris. Gene enrichment analysis was performed between the exclusively present proteins in the protozoa and D. vulgaris. Only results with p-values <0.05 were considered for analysis. Results and conclusions: A plausible explanation for the restricted occurrence of PFOR in protozoa is based on the hypothesis that bacteria serve as potential sources of genes that enhance optimal adaptation of protozoa in hostile environments. The expanded cladograms of Entamoeba and Cryptosporidium with their closely related genera substantiated this hypothesis. The exclusively expressed proteins obtained from E. histolytica and the putative bacterial gene donor, D. vulgaris, showed an over-representation of eleven genes involved in small molecule metabolism, generation of precursor metabolites, and carbohydrate metabolism. If these results can be reproduced in other PFOR-possessing protozoa, it would provide a more validated evidence to support the horizontal transfer of pfor from bacteria. Subsequent syntenic analyses of the significantly enriched genes would be required to provide further information regarding the positional relatedness of these genes at the chromosomal level. Since metronidazole is an established and well tolerated drug for treating infections caused by PFOR-possessing pathogens, it can be considered as a potential drug candidate for the treatment of infections caused by Cryptosporidium, Spironucleus and Blastocystis.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

Reducing the costs of repairing concrete structures damaged due to the appearance of cracks and reducing the number of people involved in the process of their repair is the subject of a multitude of experimental studies. Special emphasis should be placed on research involving industrial by-products, the disposal of which has a negative environmental impact, as is the case in the research presented in this paper. The basic idea was to prepare a mortar with added granulated blast furnace slag from Smederevo Steel Mill and then treat artificialy produced cracks with a Sporosarcina pasteurii DSM 33 suspension under the conditions of sterile demineralized and water from Danube river in order to simulate natural conditions. The results show a bio-stimulated healing efficiency of 32.02% in sterile demineralized water and 42.74% in Danube water already after 14 days. The SEM images clearly show calcium carbonate crystals as the main compound that has started to fill the crack, and the crystals are much more developed under the Danube water conditions. As a special type of research, microscopic images of cracks were classified into those with and without the presence of bacterial culture. By applying convolutional neural networks (ResNet 50), the classification success rate was 91.55%.

We report the isolation of two novel degrading bacterial strains active against the potential environmental pollutant acetamino-phen/paracetamol. Streptomyces Chrestomyceticus (RS2) and Streptomyces Flavofuscus (M33) collected from El-Natrun Valley, Egypt, water, sediment, and sand samples were taxonomically characterized via conidiophores morphologic characterization under Trans-mission Electron Microscope (TEM). Genotypic identification, done based on their 16S rRNA gene sequence analysis followed by BLAST alignment and deposited on the NCBI as 2 novel strains. The phylogenetic tree was constructed using an appropriate software. Acetaminophen degradation-products chemical structure was identified by GC/LC MS. The biological antimicrobial activity of some selected acetaminophen degradation-products extracts and derived compounds was examined against panel of test micro-organisms and found to be have high anti-microbial effect. In addition, in silico cheminformatics Swiss ADMET evaluation of these selected deg-radation extract for gastric absorption, distribution, hepatic metabolism, renal excretion as well as distribution to CNS and finally not mutagenic/teratogenic or genotoxic virtually. In vitro cytotoxic activity of these selected bio-degradation products was performed against HepG2 and MCF7 cancer cell lines, revealing that M33 and RS2 extract effect on acetaminophen/paracetamol bio-degradation products are potentially safe with higher IC50 on HepG2 and MCF7, in comparison to acetaminophen/paracetamol with IC50 of 108.5 μg/ml. Moreover, the in vivo acute oral single dose toxicity experiment was conducted, being compared with acetamino-phen/paracetamol to confirm that the bio-degradation products have lower toxicity than acetaminophen in vivo and in silico.

CO₂ emissions have been identified as the main driver for climate change, with devastating consequences for the global natural environment. The steel industry is responsible for ca. 8%-11% of global CO₂ emissions, due to high fossil-fuel and energy consumption. The onus is therefore on industry to remedy the environmental damage caused and to decarbonise production. This desk research report follows a two-tiered route: 1) exploring the Bio Steel Cycle; 2) proposing a seven-step strategy to overcome the challenges within the iron and steel industry. The true levels of CO₂ emissions in the steelmaking process, during the blast-furnace/basic-oxygen-furnace operation, will be detailed first, at 4.61t of CO₂ emissions/t of steel produced. The manuscript proposes a solution for reduced carbon emissions steelmaking with the Bio Steel Cycle components and detail on how to reach net-zero carbon emissions steel production. The 7-step-implementation-strategy as a potential solution to achieve net and true zero carbon emissions steel production in the short to medium-term. The findings of this are pointing towards the conclusion that CO₂ emissions seem to have been under-reported and under-estimated in the past, but the emission can be addressed if the correct scenarios for net-zero steel manufacturing are implemented by 2050.

The nutraceutical value of pomegranate in the treatment of many neoplastic, cardiovascular, viral, inflammatory, metabolic, microbial, intestinal, reproductive and skin diseases is well-documented and is linked to its richness in phenolic compounds. This study aims to evaluate nutraceutical and genetic diversity of novel pomegranate genotypes (G1-G5) in comparison to leading commercial pomegranate varieties i.e. ‘Wonderful’, ‘Primosole’, ‘Dente di Cavallo’ and ‘Valenciana’. Morphometric measurements were carried out on fruits, accompanied by chemical characterization and the development of four new polymorphic SSR markers involved in the flavonoid pathway. The cultivars displayed a marked variability in the weight and shape of fruits, as well as in the weight of arils and juice yield. The highest level of total phenolic content and antioxidant activity was found in ‘Wonderful’ and G4, while the lowest was in ‘Dente di Cavallo’. Furthermore, the results showed that the pomegranate juice, is an excellent source of minerals, especially potassium, which plays a key role in organ functioning. The new flavonoid-related markers effectively differentiated the cultivars with the same diversity pattern as morpho-chemical characterization, so the SSRs developed in the present study can be used as a rapid tool for the identification of pomegranate cultivars with relevant nutraceutical traits.

The utilisation of the industrial residual products to create new value-added materials and to reduce footprint is a modern challenge of science and industry. Development of the new multifunctional and bio-based composites is an excellent opportunity for complex utilisation of industrial residual products. The study describes the preparation and characterisation of the three-phases bio-based composites. The main components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash the cenosphere (CS). Three-phase composite prepared in the form of a block for investigation of the mechanical properties and density and a form of granules for determination of the water and oil products sorption was investigated. This work investigated the dependence of the properties on the main component DCR and CS fraction. Is found, that maximum compression strength (in block form) observed for composition without CS and DCR addition - 79.3 MPa, the second highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt% compression strength is in range 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

Delipidation is a method of defatting that is generally associated with the removal of residual lipids or lipid groups from matrices in which they are present in minute quantities. The bio-delipidation of protein-rich poultry slaughterhouse wastewater (PSW) pre-treated with a dissolved air flotation (DAF) system was developed using microbial lipases from bacterial strains isolated from the PSW. The efficacy of the bio-delipidation system was quantitatively characterised by comparing the quality parameters i.e., fats, oil and grease (FOGs), turbidity, total suspended solutes (TSS), total chemical oxygen demand (tCOD) and protein concentration of the DAF pre-treated PSW and bio-lipidized samples. As hypothesised, the bio-delipidation system was able to effectively reduce the levels of these quality parameters when crude lipases of Bacillus cereus AB1 (BF3) and Bacillus cereus CC-1 (B30) strains were used. Strain-dependent quality characteristics were also observed in bio-delipidized samples. The study successfully managed to complement physical reduction techniques (DAF) with biological strategies (bio-delipidation) for improved PSW quality, with potential industrial applications.

Cenobamate is approved by the European Medicine Agency for the treatment of adult patients with epilepsy (PWEs) who suffer from ongoing focal-onset seizures despite appropriate treatment with at least two established antiseizure medications. Pivotal trials and post-marketing real-world observational studies have suggested a high efficacy with unusually high seizure-free rates. We sought to investigate the serum trough levels of cenobamate under steady-state conditions in seizure-free versus non-responding PWEs, and in PWEs who experienced adverse events versus those who did not. We analyzed samples from 101 PWEs treated with adjunct cenobamate under steady-state conditions. In all, 36 PWEs were seizure-free and 65 were non-responders. In 31 PWEs, adverse events were apparent, whereas in the remaining 70, no tolerability issues were reported. We found a linear correlation between the daily doses (range: 100 mg – 400 mg) and the plasma levels (3.8 mg/l – 54.6 mg/l). Neither the daily doses nor the plasma levels differed significantly between seizure-free and non-responding PWEs or between PWEs with a satisfactory tolerability and those who experienced adverse events. The main reason for this result was that the individual therapeutic ranges varied widely: seizure freedom and adverse effects were observed alongside low doses and plasma levels in some PWEs. Conversely, there were examples of PWEs who did not respond or who reported no tolerability issues at high doses or plasma levels. Still, to evaluate the individual therapeutic range and to better understand the influence of other drugs in cases where concomitant medications are used, the therapeutic drug monitoring of cenobamate may be useful.

Intermittently Scanned Continuous Glucose Monitoring (isCGM) devices are increasingly being used in patients with type 2 diabetes mellitus (T2DM) on insulin therapy for their benefits regarding disease management. Evidence of isCGM use in patients with T2DM treated with basal insulin or oral antidiabetic drugs is lacking. The aim of this study was to assess the efficacy and safety of isCGM in this population. This was an observational, retrospective, real-world study enrolling patients with T2DM who were starting with the use of isCGM. Data from medical records (i.e. demographics, clinical characteristics, laboratory assessments, and isCGM metrics) were collected over three time periods (baseline, 3 and 6 months). The endpoints were glycated haemoglobin (HbA1c) changes, and changes in isCGM metrics as defined by the International Consensus from baseline to a 3-month and a 6-month follow-up. Overall, 132 patients were included (69% male; mean age 68.2±11.0 years; mean disease duration 19.0±9.3 years; 80% on basal insulin ± oral drugs at baseline; mean baseline HbA1c 8.1%±1.3%). The estimated mean change in HbA1c from baseline was statistically significant at three (-0.4±1.0%; p=0.003) and at six months (-0.6±1.3%; p&lt;0.0001). No statistical differences were found in the mean change of the isCGM metrics. Intermittently Scanned Continuous Glucose Monitoring is effective and safe in improving glycaemic control in patients with type 2 diabetes treated with basal insulin or oral antidiabetic drugs.

Collecting and recording physiological parameters and forwarding this data via telemedicine or remote surveys may significantly increase the health and safety of people working under extreme environmental conditions, like firefighters, mountain rescuers, disaster control employees, military personnel, etc. First, ruggedized systems, as small, lightweight, and flexible as possible, are needed to optimize the goal of increasing occupational health and safety of persons at risk and maximizing their performance during missions. Previous systems could only record a very limited number of parameters, and a few could forward the data online to return information to the user. Therefore, in order to record several meaningful, valid, and reliable physiological parameters synchronized, an extension of existing systems is required. This review highlights this problem and gives an overview of the historical development. The actual status of the systems available was listed and described comparatively. In the end, a proven, promising, and innovative solution is presented that can solve the problem and allow people to work more safely in extreme environments, which may represent the future.

One of the main challenges in geodetic deformation analysis is to infer whether the geometry of some engineering structures or zones of natural hazards has changed from their initial state or not. The pillar that supports such an analysis is tightly based on the fundamentals of statistical hypothesis testing. The null hypothesis model indicates that no displacement has occurred. It is tested against a class of alternative models, which stipulate different displacement patterns. In this contribution, we present an innovative geodetic displacement detection which integrates combinatorial analysis and likelihood ratio tests into a sequential procedure for the case where the differences between observations of two epochs are in play. This framework is applied and investigated to two test scenarios: a synthetic and a real simulated trilateration network. From a statistical point of view, our approach is rigorous, because the alternative model can identify simultaneously more than one unstable point. In addition, the relationship between the unknown parameters and the observations is always linear, even if the problem manifests itself as non-linear. Consequently, we avoid a potential loss of statistical test power due to the model linearization. In addition, the proposed method controls the false positive rate efficiently. One of the problems that arise here is also related to the selection of the maximum number of points to be considered in the test procedure ( ). Here, we provide an innovative methodology based on rank computation of the design matrices to define , which can even be extended to the problem of outlier detection. Determining avoids the problem of having non-separable models in identifying unstable points. The algorithms and data are available in the repository.

This paper presents the results of experiments on the study of a hydraulic fracture interaction with a preliminary created fracture that simulates a natural fracture. A distinctive feature of the conducted experiments is the ability to use an ultrasonic sounding to measure the fracture propagation and opening simultaneously with the fluid pore pressure measurements at the several points of the porous saturated sample. It allows to obtain the pressure distributions at various experiment stages and to establish a relation between the pore pressure distribution and the hydraulic fracture propagation and its interaction with macroscopic natural fracture. The possibilities of active ultrasonic monitoring have been expanded due to preliminary calibration experiments, which make it possible to estimate the fracture opening value by attenuation of ultrasonic pulses. The experiments show that the fracture propagation is limited by the natural fracture. This is caused by the hydraulic fracturing fluid leaks into the natural fracture, so both hydraulic fracture and natural fracture compose united hydraulic system.

Natural vegetation restoration can take decades to achieve and requires information on species composition and trend to inform management strategies. Here we demonstrate the potential and portability of drone, dove and Sentinel-2 imagery for species level classification and trajectory monitoring using three study sites with different revegetation histories. Drone imagery (4 cm) was classified using random forests. Dove (3 m) and Sentinel-2 (10 m) images were acquired close to the anniversary of the drone flights and converted into fractional cover maps showing the proportion of exotics, natives and other land covers using ordinary least squares (OLS) and geographically weighted regression (GWR). The time series of fractional cover maps were converted into positive and negative slope and second-order curvature and summarised as one RGB composite to illustrate trend and observe exotic expansion. Drone classification accuracies ranged from 73%-76% when applied to the full plant species list and between 93% and 97% when grouped into natives, exotics, and other land covers. GWR outperformed OLS for all fractional cover mapping and GWR with dove imagery was more accurate than with Sentinel imagery. The combination of very high-resolution drone acquired imagery with the versatility of dove acquired imagery arms land managers with highly accurate species composition and their spatio-temporal dynamics to promote timely intervention.

Rail, as the cleanest and greenest high-volume transport, has a central role in the decarbonizing, and it is expected to become the backbone of future mobility in the world. It is worthy to highlight that rail generates the lowest CO2 emissions and energy consumption in operation with respect to the other transportation modes but during construction and maintenance phases CO2 emission, energy consumption and other environmental impacts are significant and need to be carefully assessed and properly mitigated. This paper, based on an extensive literature review, provides a comprehensive framework of trends and challenge in railway sustainability. Attention is focused on track and related materials, maintenance strategies, and methods of assessment of the sustainability. Results show that improvement of materials and practices used in construction and appropriate strategies in maintenance, supported by effective monitoring of the state of the track, can reduce the negative effects on the environment and society and contributes to make this transportation mode greener. Proper methods for the assessment of the sustainability, (LCA, Circularity Index) help to quantify the potential of environmental enhancement of different solutions and constitute effective and indispensable tools in the decision-making process.

Decapod crustaceans are important components of the fauna of soft bottom habitats. In this work, biogeographical updates of decapod crustaceans are provided through the analysis of a large soft bottom benthic macroinvertebrates data set of the central Mediterranean Sea. Decapod crustacean assemblages were collected in the last twenty years by a Van Veen grab on 42 study sites located along the Italian coasts at depths ranging from the surface up to 120 meters. Spatial distribution of the crustaceans examined, which include 123 species belonging to 40 families, has been investi-gated according to the biogeographical zones identified in the Italian Seas. Spatial distribution of 39 species has been updating, comparing the ISPRA decapod crustacean dataset with the most recent Italian checklists. For the species updated, number of specimens and environmental data, such as bathymetric range and habitat details, are provided for each site investigated. Data are discussed and compared with the existing literature, also referring to what is reported in the World Register of Marine Species (WoRMS), with the aims to contribute to the knowledge of biodiversity of the marine species provide useful data to assist the insiders to update checklists and registers at national and global scale and information on species ecology.

Electrochemical biosensors based on immobilized enzymes are among the most popular and commercially successful biosensors. Literature in this field suggests that modification of electrodes with nanomaterials is an excellent method for enzyme immobilization, which can greatly improve the stability and sensitivity of the sensor. However, the poor stability, weak reproducibility, and limited lifetime of the enzyme itself still limit the requirements for the development of enzyme electrochemical biosensors for food production process monitoring. Therefore, constructing sensing technologies based on enzyme electrochemical biosensors remains a great challenge. This article outlines the construction principles of four generations of enzyme electrochemical biosensors and discusses the applications of single-enzyme systems, multi-enzyme systems and nano-enzyme systems developed based on these principles. The article further describes methods to improve enzyme immobilisation by combining different types of nanomaterials such as metals and their oxides, graphene-related materials, metal-organic frameworks, carbon nanotubes and conducting polymers. In addition, the article highlights the challenges and future trends of enzyme electrochemical biosensors, providing theoretical support and future perspectives for further research and development of high-performance enzyme chemical biosensors.

River monitoring has the potential to grow substantially with present-day available affordable and locally sourced hardware. Yet river monitoring networks are still under pressure due to lack of resources, difficulties with maintenance, and rapidly changing conditions which in part may be due to climate change. We advocate that to turn around this trend, monitoring stations must rely on local people, work with locally available devices, work without contact with water and operate through openly available knowledge. River observations with camera videos have this potential. IP cameras, drones or smartphones are widely available as observation platforms. The scientific methods are well established in literature. Yet current attempts to establish scalable open-source software solutions that can be operated anywhere are lacking. In fact, currently available software is either research-oriented, more aimed at incidental observations, is restricted to single-use licenses, entirely proprietary, or restricted to operations through a third-party Software as a Service. To overcome this obstacle, we present OpenRiverCam, a free and open-source software ecosystem for river observations that can fulfill a wide variety of use cases and business cases through a well-documented and simple to use Application Programming Interface, service workflows, cloud scalability and interoperability, and options to extend to several applications within the hydrological, hydrodynamic, environmental and geospatial domains. We demonstrate its current technical abilities through three different case studies that all originate from a user perspective. We discuss the future developments to meet further requirements, which include documentation, widely available training materials and embedding in curricula, and further hardware and software developments.

As required by the EU legislation and the national risk management duties, the pesticide residues were determined by four specialized laboratories in 9,924 samples taken from 119 crops of economic importance and imported foodstuffs during 2017-2021 in Hungary. The screening method applied covered 622 pesticide residues as defined for enforcement purposes. The limit of detection ranged between 0.002-0.008 mg/kg. The 1.0% violation rate was lower than in the European Union for all commodities. No residue was detectable in 45.9% of the samples. For detailed analyses of the results, eight commodities (apple, cherry, grape, nectarine/peach, sweet peppers, and strawberry) were selected as they were analyzed over 195 samples and contained most frequently residues. Besides testing their conformity with national MRLs, applying 0.3MRL action limits for pre-export control, we found that 73% of the sampled lots would be compliant with ≥90% probability based on second independent sampling. Multiple residues (2-23) in one sample were detected in 36-50% of the tested lots. Noting the provisions of integrated pest management and the major pests and diseases of selected crops, normally 3-4, exceptionally 7-9 active ingredients of different mode of actions should be sufficient for their effective and economic protection.

Equines play an important role throughout the world, whether for work, culture, or leisure, providing an ever-growing significant contribution on the economy. The increase in importation and movement of horses, both nationally and internationally, has inevitably allowed for the global equine industry to grow. Subsequently however, the potential for transmission of fatal equine bacterial diseases has also escalated, and devasting outbreaks continue to occur. To prevent such events, disease surveillance and diagnosis must be heightened throughout the industry. Current common, or "gold-standard" techniques, have shown to be inadequate at times, thus requiring newer technology to impede outbreaks. Loop-mediated isothermal amplification (LAMP) has proven to be a reliable, rapid, and accessible tool in both diagnostics and surveillance. This review will discuss equine bacterial diseases of biosecurity relevance and their current diagnostic approaches, as well as their respective LAMP assay developments. Additionally, we will provide insight regarding newer technology and advancements associated with this technique, and their potential use for the outlined diseases.

Programmable Object Interfaces are increasingly intriguing researchers because of their broader applications, especially in the medical field. In Wireless Body Area Network (WBAN), for example, the patients’ health can be monitored using clinical nano sensors. Exchanging such sensitive data requires a high level of security and protection against attacks. To that end, the literature is rich with security schemes that include the advanced encryption standard, secure hashing algorithm, and digital signatures that aim to secure the data exchange. However, such schemes elevate the time complexity rendering the data transmission slower. Cognitive Radio technology with a medical body area network system involves communication links between WBAN gateways, server and nano sensors rendering the entire system vulnerable to security attacks. In this paper, a novel DNA-based encryption technique is proposed to secure medical data sharing between sensing devices and central repositories. It has less computational time throughout authentication, encryption, and decryption. Our analysis of experimental attack scenarios shows that our technique is better than its counterparts.

This contribution shows the possibilities of a low-cost multipurpose data logger that was built around an Arduino Mega 2560 single board computer. To transform the Arduino Mega into such a data logger, a sensor shield was designed that contains an SD-card, real-time clock, and different kinds of connectors so that sensors can easily be attached to the device. The software considers a wide range of predefined sensors from which a user can choose. To assess the performance of such a device, short-term monitoring campaigns in relation to outdoor air quality, human activity in an office, motion of a journey on a bike, and exhaust gas monitoring of a diesel generator were realized. Besides the possibilities to apply the data logger in different kinds of applications, a method is proposed to assess the credibility of such a system. The assessment based on the various short-term campaigns showed that the system scores positively on most of the performance indicators, but that unexpected (black swan) events affect the assessment over the longer term. This makes the development of low-cost scientific instruments harder than expected. The stability and long-term performance of this type of design requires continuous evaluation and engineering correction.

Plant Factory Transplanter (PFT) is a key component of the plant factory system. Its operation status directly affects the quality and survival rate of planted seedlings, which in turn affects the overall yield and economic efficiency. To monitor the operation status and transplanting quality of a transplanting machine in a timely manner, the primary task is to use a computerized and easy-to-use method to monitor the transplanting units. Inspired by the latest developments in augmented reality and robotics, a DT model-based and data-driven online monitoring method for plant factory transplanting equipment is proposed. First, a data-driven and virtual model approach is combined to construct a multi-domain digital twin of the transplanting equipment. Then, taking the vibration frequency domain signal above the transplanting manipulator and the image features of the transplanting seedling tray as input variables, the evaluation method and configuration method of the PFT digital twin system are proposed. Finally, the effect of the transplanter is evaluated, and the cycle can be repeated to optimize the transplanter to achieve optimal operation parameters. The results show that the digital twin model can effectively use the sensor data to identify the mechanical vibration characteristics and avoid affecting transplanting quality due to mechanical resonance. At a transplanting rate of 3000 plants/h, the transplanting efficiency can be maintained at a high level and the vibration signal of X, Y, Z-axis above the transplanting manipulator is relatively calm. In this case, Combined the optimal threshold method with the traditional Wiener algorithm, the identification rate of healthy potted seedlings can reach 94.3%. Through comprehensively using the optimal threshold method and 3D block matching filtering algorithm for image threshold segmentation and denoising, the recognition rate of healthy seedlings has reached over 96.10%. In addition, the developed digital twin can predict the operational efficiency and optimal timing of the detected transplanter, even if the environmental and sensor data are not included in the training. The proposed digital twin model can be used for damage detection and operational effectiveness assessment of other plant factory equipment structures.

Condition monitoring is today a crucial and unavoidable practice related to the use of widespread mechanical components as rolling element bearings. Despite the diffusion of new data-driven techniques to analyze vibrational signals and detect the state of health of the system, mathematical tools, deriving more or less directly from the Fourier transform and defined either on the time or the frequency domain or on a combination of them (i.e. signal-based techniques), remain still essential and irreplaceable in the light of the deep and detailed information they provide. In this paper the diagnostic efficacy of an ample spectrum of these methods is investigated, applying them to study faults occurrence in the first bearing dataset released by NASA IMS Center. Thanks to their analytical definition, which is formulated taking into consideration to some extent the mathematical nature of the signal, faults signatures can be clearly identified and their temporal development can be fully traced, confirming their ability as powerful means to constantly monitor the state of a system even in real-time applications.

The application of movement-detection sensors is crucial for understanding surface movement and tectonic activities. The development of modern sensors has been instrumental in earthquake monitoring, prediction, early warning, emergency commanding and communication, search and rescue, and life detection. There are numerous sensors currently being utilized in earthquake engineering and science. It is essential to review their mechanisms and working principles thoroughly. Hence, we have attempted to review the development and application of these sensors by classifying them based on the timeline of earthquakes, physical or chemical mechanisms of sensors, and location of sensor platforms. In this study, we analyzed all available sensor platforms that have been widely used in recent years, with satellites and UAVs being among the most used. The findings of our study will be useful for future earthquake response and relief efforts, as well as research aimed at reducing earthquake disaster risks.

To explore the effects of pymetrozine on the reproductive behavior of N. lugens, we established a bioassay method to accurately evaluate the toxicity of pymetrozine in N. lugens and establish the level of pymetrozine resistance of N. lugens in the field. In this study, pymetrozine’s effects on the fecundity of N. lugens were evaluated using the topical application method and rice-seedling dipping method. Moreover, the resistance of N. lugens to pymetrozine in a pymetrozine-resistant strain (Pym-R) and two field populations (YZ21 and QS21) was determined using the rice-seedling dipping method and fecundity assay methods. The results showed that treatment of N. lugens third-instar nymphs with LC15, LC50, and LC85 doses of pymetrozine resulted in significantly reduced male fertility and female fecundity. In addition, N. lugens adults treated with pymetrozine using the rice-seedling dipping and topical application method also exhibited significantly in-hibited male courtship, fertility, and female receptivity. Using the rice-stem dipping method, pymetrozine resistance was shown to be at high levels in Pym-R (194.6-fold), YZ21 (205.9-fold), and QS21 (212.8-fold), with LC50 values of 522.520 mg/L (Pym-R), 552.962 mg/L (YZ21), and 571.315 (QS21) mg/L. However, when using the rice-seedling dipping or topical application fe-cundity assay method, Pym-R (EC50: 14.370 mg/L, RR=12.4-fold; ED50: 0.560 ng/adult, RR=10.8-fold), YZ21 (EC50: 12.890 mg/L, RR=11.2-fold; ED50: 0.280 ng/adult; RR=5.4-fold), and QS21 (EC50: 13.70 mg/L, RR=11.9-fold) exhibited moderate or low levels of resistance to pymet-rozine. Our studies show that pymetrozine can significantly inhibit the fecundity of N. lugens. The fecundity assay results showed that N. lugens only developed low to moderate levels of resistance to pymetrozine, indicating that pymetrozine can still achieve effective control on the next gen-eration of N. lugens populations.

We present a custom platform that integrates data from several sensors measuring synchronously different variables of the beehive and wirelessly transmits all measurements to a cloud server. There is a rich literature on beehive monitoring. The choice of our work is not to use ready platforms such as Arduino and Raspberry Pi and to present a low cost and power solution for long term monitoring. We integrate sensors that are not limited to the typical toolbox of beehive monitoring such as gas, vibrations and bee counters. The synchronous sampling of all sensors every 5 minutes allows us to form a multivariable timeseries that serves two-ways: a) it provides immediate alerting in case a measurement exceeds predefined boundaries that are known to characterize a healthy beehive, and b) based on historical data predict future levels that are correlated with hive’s health. Finally, we demonstrate the benefit of using additional regressors in the prediction of the variables of interest. The database, the code and a video of the vibrational activity of two months are made open to the interested readers.

In the current research work, electrical resistance tomography (ERT) was employed for crystallization process monitoring and visualization. A first-of-its-kind MATLAB-based interactive GUI application “ERT-Vis” is presented. Two case studies involving varied crystallization methods were undertaken. The experiments involving calcium carbonate reactive (precipitative) crystallization for the high conductivity solution-solute media and the cooling crystallization for sucrose crystallization representing the lower conductivity solution-solute combination were designed and performed. The software successfully provided key insights regarding the process progress in both crystallization systems. It could detect and separate the crystal agglomerations in the low as well as high conductivity solutions using visual analytics tools provided. The performance and utility of the software were studied using a software evaluation case study involving domain experts. Participant feedback indicated that ERT-Vis software helps in reconstructing images instantaneously, interactively visualizing, and evaluating the output of the crystallization process monitoring data.

The global financial crisis of 2008, triggered by the collapse of Lehman Brothers, highlighted a banking system that was widely exposed to systemic risk. The minimization of the systemic risk via a close and detailed monitoring of the entire banking network became a priority. This is a complex and demanding task considering the size of the banking systems: in the US and the EU they include more than 10000 institutions. In this paper, we introduce a methodology which identifies a subset of banks that can: a) efficiently represent the behavior of the whole banking system and b) provide, in the case of a failure, a plausible range of the crisis dispersion. The proposed methodology can be used by the regulators as an auxiliary monitoring tool, to identify groups of banks that are potentially in distress and try to swiftly remedy their problems and minimize the propagation of the crisis by restricting contagion. This methodology is based on Graph Theory and more specifically Complex Networks. We termed this setting a “multivariate Threshold – Minimum Dominating Set” (mT–MDS) and it is an extension of the Threshold – Minimum Dominating Set methodology (Gogas e.a., 2016). The method was tested on a dataset of 570 U.S. banks: 429 solvent and 141 failed ones. The variables used to create the networks are: the total interest expense, the total interest income, the tier 1 (core) risk-based capital and the total assets. The empirical results reveal that the proposed methodology can be successfully employed as an auxiliary tool for the efficient supervision of a large banking network.

Abstract: In the last five years, the urban development of Limassol City has rapidly increased in the sectors of industry, trade, real estate, and many others. This exponentially increased urban development introduces several concerns about the aggravation of the land subsidence in the Limassol coastal front. Fifty Copernicus Sentinel-1 data from 2017-2021 have been processed and analyzed using the Sentinel Application Platform (SNAP) and the Stanford Method for Persistent Scatters (StaMPS). A case study for the identification and analysis of the elements (PS) in pixels in a series of interferograms, and then, the quantity of the land displacements in the Line of Sight, in the Limassol coastal front, is presented in this research, with the subsidence rates up to about (-5 to 4 mm / year). For the validation of the detected deformation, accurate ground-based geodetic measurements along the coastal area were used. Concordantly, taking into account that there are a significant number of skyscrapers planned to be built, this study attempts a preliminary assessment of the impact these structures will pose on the coastal front of the area of Limassol.

In the present work, cost-effective strain gauges were fabricated by using inkjet printing and photonic curing on flexible and recyclable PET substrates. Ohmic resistance (a.k.a. DC resistance) (R0) and complex electrical impedance (Z) as a function of test frequency were characterized, respectively, with the state-of-the-art electronic testing equipments. For the fabrication process, commercially available silver nanoparticle (AgNP) inks and printing substrates were used in order to eliminate any apriori ink processing. In order to validate the in-house cantilever beam measurement setup and devices, first, commercially available metallic foil strain gauges (with the provided gauge factor GF=2 by the manufacturer) were tested at different locations. Thereafter, the printed strain gauges were investigated with several repetitions at different measurement locations. The measurement results demonstrated an affordable, rapid and tailorable design and repeatable fabrication approach for strain gauges with GFavg~6.6, which has potential applications in remote sensing and structural monitoring applications.

In response to the complex social, environmental and economic situation caused by the "Terra dei Fuochi" phenomenon, the IZSM collaborated closely with the Terra dei Fuochi working group, carrying out additional monitoring surveys both on food (QR Code Campania project[30]), and on the environment (Campania Trasparente project[31]). This model was developed in the context of the experience accumulated in the field of environmental and food monitoring, and represents an innovative tool aimed at increasing knowledge of the environmental context of the Campania Region through an objective, integrated and organic synthesis of complex environmental phe-nomena and territorial dynamics. The model proposed here is useful for the global and synthetic assessment of environmental pressure on a municipal basis. As shown, it can also be applied to aggregations of municipalities. Furthermore, it can be used in the context of institutional actions for the planning and monitoring of improvements on a local or regional scale. Finally, the pro-posed municipality-based environmental pressure index represents the basis for geo-stratification of the sample in the context of population biomonitoring studies on a regional scale, as in the described biomonitoring study design applicable to the Campania Region.

Understanding the relationships between land cover/urban structure patterns and air pollutants is key to sustainable urban planning and development. In this study, we employ a mobile monitoring method to collect PM_2.5 and BC data in the city of Philadelphia, PA during the summer of 2019 and apply the Structure of Urban Landscapes (STURLA) methodology to examine relationships between urban structure and atmospheric pollution. We find that, while PM_2.5 and BC vary by STURLA class, many of the differences in pollutant concentrations between classes are not significant. However, we also find that the proportions in which STURLA components are present throughout the urban landscape can be used to predict urban air pollution. Among frequently sampled STURLA classes, gpl hosted the highest PM_2.5 concentrations on average (16.60 _± 4.29 µg/m³), while tgbwp hosted the highest BC concentrations (2.31 _± 1.94 µg/m³). Furthermore, STURLA combined with machine learning modeling was able to correlate PM_2.5 (R²= 0.68, RMSE 2.82 µg/m³) and BC (R² = 0.64, RMSE 0.75 µg/m³) concentrations with the urban landscape and spatially interpolate concentrations where sampling did not take place. These results demonstrate the efficacy of the STURLA methodology in modeling relationships between air pollution and land cover/urban structure patterns.

The air pollutant NO2 is derived largely from transportation sources and is known to cause respiratory disease. A substantial reduction in transport and industrial processes around the globe from the novel SARS-CoV-2 coronavirus and subsequent pandemic resulted in sharp declines in emissions, including for NO2. Additionally, the COVID-19 disease that results from the coronavirus may present in its most severe form in those who have been exposed to high levels of air pollution. To explore these links, we compared ground-based NO2 sensor data from 11 US cities from a two-month window (March-April) over the previous five years versus the same window during 2020 shutdowns. NO2 declined roughly 12-41% in the 11 cities. This decreased coincided with a sharp drop in vehicular traffic from shutdown-related travel restrictions. To explore this link more closely, we gathered more detailed traffic count data in one city, Indianapolis, Indiana, and found a strong correlation between traffic counts/classification and vehicle miles travelled, and a moderate correlation between NO2 and traffic related data. This finding indicates that we can use such analysis in targeting reduction in pollutants like NO2 by examining and manipulating traffic patterns, thus potentially leading to more population-level health resilience in the future.

The assessment of water quality consists of counting bacteria indicating fecal contamination or detecting the presence of pathogenic bacteria using standardized or validated methods of classical microbiology. Our present study aims to determine the bacteriological quality of drilling water in the Tandjilé region of Chad. Our method used was based on qualitative and quantitative research on suspected total coliforms, Echerichia Coli and fecal enterococci were analyzed according to the standard routine methods of the French Association for Normalization (AFNOR). Microbiological analysis shows the presence of indicators of fecal contamination such as total coliforms, Escherichia coli and fecal enterococci. The number of strains detected in 100 ml were E. coli (7 /29 samples), fecal Streptococcus (6 /29 samples) and total coliforms (29/29 samples), respectively from borehole water. The contamination rate of E. coli is 24.13%, total coliforms 100% and 20.68% of fecal enterococci in boreholes. The high number of these microorganisms is more than the values recommended by the WHO for the quality of drinking water. Corrective and urgent measures are needed to improve the quality of these water resources, rich in pathogens, which are health risks, and the causes of infectious diseases such as gastroenteritis, diarrhea, typhoid and skin diseases.

Precision agriculture is a technology used by farmers to help food sustainability amidst growing population. One of the tools of precision agriculture is yield monitoring, which helps a farmer manage his production. Yield monitoring is usually done during harvest, however it could also be done early in the growing season. Early prediction of yield, specifically for fruit trees, aids the farmer in the marketing of their product and assists in managing production logistics such as labor requirement and storage needs. In this study, a machine vision system is developed to estimate fruit yield early in the season. The machine vision system uses a color camera to capture images of fruit trees during the full bloom period. An image segmentation algorithm based on an artificial neural network was developed to recognize and count the blossoms on the tree. The artificial neural network segmentation algorithm uses color information and position as input. The resulting correlation between the blossom count and the actual number of fruits on the tree shows the potential of this method to be used for early prediction of fruit yield.

Remote sensing has been used as an important tool for disaster monitoring and disaster scope extraction, especially for the analysis of spatial and temporal disaster patterns of large-scale and long-duration series. Based on the Google Earth Engine cloud platform, this study used MODIS vegetation index products with 250-m spatial resolution synthesized over 16 days from the period 2005–2019 to develop a rapid and effective method for monitoring disasters across a wide spatiotemporal range. Three types of disaster monitoring and scope extraction models are proposed: the normalized difference vegetation index (NDVI) median time standardization model (R_{NDVI_TM(i)}), the NDVI median phenology standardization model (R_{NDVI_AM(i)(j)}), and the NDVI median spatiotemporal standardization model (R_{NDVI_ZM(i)(j)}). The optimal disaster extraction threshold for each model in different time phases was determined using Otsu’s method, and the extraction results were verified by medium-resolution images and ground-measured data of the same or quasi-same period. Finally, the disaster scope of cultivated land in Heilongjiang Province from 2010–2019 was extracted, and the spatial and temporal patterns of the disasters were analyzed based on meteorological data. This analysis revealed that the three aforementioned models exhibited high disaster monitoring and range extraction capabilities, with verification accuracies of 97.46%, 96.90%, and 96.67% for R_{NDVI_TM(i)}, R_{NDVI_AM(i)}, and _(j)R_{NDVI_ZM(i)(j)}, respectively. The spatial and temporal disaster distributions were found to be consistent with the disasters of the insured plots and the meteorological data across the entire province. Moreover, different monitoring and extraction methods were used for different disasters, among which wind hazard and insect disasters often required a delay of 16 days prior to observation. Each model also displayed various sensitivities and were applicable to different disasters. Compared with other techniques, the proposed method is fast and easy to implement. This new approach can be applied to numerous types of disaster monitoring as well as large-scale agricultural disaster monitoring and can easily be applied to other research areas. This study presents a novel method for large-scale agricultural disaster monitoring.

Neuromuscular disorders cause progressive muscular weakness, which limits upper extremity mobility and performance during activities of daily life. A dynamic arm support can improve mobility and quality of life. However, their use is often discontinued over time for unclear reasons. This study aimed to evaluate whether users of dynamic arm supports demonstrate and perceive quantifiable mobility benefits over a period of two months. Nine users of dynamic arm supports were included in this observational study. They had different neuromuscular disorders and collectively used four different arm supports. They were observed for three consecutive weeks during which they were equipped with a multi-sensor network of accelerometers to assess the actual use of the arm support and they were asked to provide self-reports on the perceived benefits of the devices. Benefits were experienced mainly during anti-gravity activities and the measured use did not change over time. The self-reports provided contextual information in domains such as participation to social life, in addition to the sensor system. However self-reports overestimated the actual use by up to three-fold compared to the accelerometer measures. A combination of objective and subjective methods is recommended for meaningful and quantifiable mobility benefits during activities of daily life.

This paper proposes a novel data processing framework dedicated to bedload monitoring in underwater environments. After calibration, by integration the total energy in the nominal bandwidth, the proposed experimental setup is able to accurately measure the mass of individual sediments hitting the aluminum plate. This require a priori knowledge of the vibration trasients in order to match a predefined dictionary. Based on unsupervised hierarchical agglomeration of complex vibration spectra, the proposed algorithms allow to accurately localize the transients corresponding to the shocks created by sediment impacts on a steel plate.

Proper satellite-based crop monitoring applications at the farm-level often require near-daily imagery at medium to high spatial resolution. The synthesizing of ongoing satellite missions by ESA (Sentinel 2) and NASA (Landsat7/8) provides this unprecedented opportunity at a global scale; nonetheless, this is rarely implemented because these procedures are data demanding and computationally intensive. This study developed a complete stream processing in the Google Earth Engine cloud platform to generate harmonized surface reflectance images of Landsat7,8 and Sentinel 2 missions. The harmonized images were generated for two agriculture schemes in Bekaa (Lebanon) and Ninh Thuan (Vietnam) during the period 2018-2019. We evaluated the performance of several pre-processing steps needed for the harmonization including image co-registration, brdf correction, topographic correction, and band adjustment. This study found that the miss-registration between Landsat 8 and Sentinel 2 images, varied from 10 meters in Ninh Thuan, Vietnam to 32 meters in Bekaa, Lebanon, and if not treated, posed a great impact on the quality of the harmonized dataset. Analysis of a pair overlapped L8-S2 images over the Bekaa region showed that after the harmonization, all band-to-band spatial correlations were greatly improved from (0.57, 0.64, 0.67, 0.75, 0.76, 0.75, 0.79) to (0.87, 0.91, 0.92, 0.94, 0.97, 0.97, 0.96) in bands (blue, green, red, nir,swir1,swir2, ndvi) respectively. We demonstrated that dense observation of the harmonized dataset can be very helpful for characterizing cropland in highly dynamic areas. We detected unimodal, bimodal and trimodal shapes in the temporal NDVI patterns (likely cycles of paddy rice) in Ninh Thuan province only during the year 2018. We fitted the temporal signatures of the NDVI time series using harmonic (Fourier) analysis. Derived phase (angle from the starting point to the cycle's peak) and amplitude (the cycle's height) were combined with max-NDVI to generate an R-G-B image. This image highlighted croplands as colored pixels (high phase and amplitude) and other types of land as grey/dark pixels (low phase/amplitude). Generated harmonized datasets that contain surface reflectance images (bands blue, green, red, nir, swir1, swir2, and ndvi at 30 meters) over the two studied sites are provided for public usage and testing.

Background: It is well known the adverse effect of mercury exposure on pregnant women and newborns. Interactions between environmental factors and individual genetic susceptibility have been identified, particularly polymorphisms of codifying genes for the Glutathione S-transferase family (GSTs). Herein, we report a case series of patients with high Hg levels in biosamples. Case Series: Fourteen cases with high Hg levels were identified. Non-occupational or home exposure risk factors were identified. All mothers reported fish consumption during pregnancy. Almost 60% of the individuals were null for either one GSTs gene. To date, in the subsequent mother-child pairs toxicology controls no signs or symptoms of poisoning were identified and most of the mercury levels decreased and are below the accepted limit. Discussion: In this case series we found some similarities with the literature; among them, the relation of Hg ratio in maternal blood and umbilical cord, a possible exposure factor is the consumption of fish during pregnancy and, the high levels of Hg may be related with susceptibility biomarkers such as GSTs gene polymorphisms. This case series highlights the need to develop studies that evaluate the interactions between environmental factors and individual genetic susceptibility. Additionally, the importance of evaluating which Colombian fish species present the highest levels of Hg.

This paper describes a multi-channel in-situ monitoring system developed to better understand defect formation signatures in metal additive manufacturing. Three high-speed imaging modes coupled with an image computer capable of processing and storing these data streams allowed an examination of defect formations signatures and mechanisms. It was found that defects later detected in X-ray computed tomography (CT) scans were related to regions with anomalous heat signatures and powder bed morphology. Automated defect detection algorithms based on these defect signatures captured 80% of defects greater than 300 µm.

High throughput multiplex serological systems enable the small developer to set up tests at small cost, for microbes for which there are no commercial tests, and for aspects which have not been addressed by them. An example is testing for Zika and Tick Borne Encephalitis virus antibodies, where antigenic cross-reactions make diagnosis problematic. Our technique variant, Suspension Multiplex Immunoassay (SMIA) allows many samples to be tested for antibodies to many antigens in a short time. Computational compensation for cross-reactions is possible if a SMIA panel contains most of the potentially cross-reacting antigens. Using antibody avidity and pattern of reactivity to whole virus and nonstructural protein, antibodies due to vaccination and infection, respectively, as well as probable degree of protection, can be determined with high throughput. These multiplex techniques hold great promise for future diagnostic development. Theoretically, even large scale serological monitoring, like blood donor pathogen testing, could be done inexpensively and rationally with multiplex serology developed in house. However, the quality control demands are steep and in most cases out of scope for a single laboratory. There remain however a number of clinical applications where in house multiplex serology can be performed with adequate quality control under high throughput conditions.

When a rotary machine is running, from which the acquired vibro-acoustic signals enable to reveal its operation status and health condition. The study proposed a DSP-based adaptive angular-velocity Vold-Kalman filtering order tracking (AV2KF_OT) algorithm with an online real-time nature for signal interpretation and machine condition monitoring. Theoretical derivation and numerical implementation of computation schemes are briefly introduced. An online real-time monitoring system based on the AV2KF_OT algorithm, which was implemented through both a digital signal processor and a user interface coded by using LabVIEW, was developed. Two experimental tasks were applied to justify the proposed technique, including (i) the detection of startup on the fluid-induced whirl performed through a journal-bearing rotor rig, and (ii) the separation of close orders from the measured signals of a multifunction transmission-element ball-bearing bench.

Wearable sensors for human physiological monitoring have attracted tremendous interest from researchers in recent years. However, most of the research was only done in simple trials without any significant analytical algorithms. This study provides a way of recognizing human motion by combining textile stretch sensors based on single-walled carbon nanotubes (SWCNTs) and spandex fabric (PET/SP) and machine learning algorithms in a realistic applications. In the study, the performance of the system will be evaluated by identification rate and accuracy of the motion standardized. This research aims to provide a realistic motion sensing wearable products without unnecessary heavy and uncomfortable electronic devices.

This research presents alternative solutions for an Energy Efficiency Management System (EEMS) serving as a framework for optimizing the energy consumption algorithm and lowering energy consumption. First, a monitoring Wireless Sensor and Actuator Network (WSAN) is used for sensing, measuring, gathering data, and modeling all the dynamic disturbance parameters of the rooms in the building. Second, integrated software for metering and controlling the processes of digital data flow is used. Third, an alternative solution is proposed to reduce energy consumption. The primary benefits of this system are real-time monitoring; rapid, alternative solutions; and the ability to make a prudent decision on how to lower energy consumption. The system shows instant and accumulated solutions for short and long-term time planning. The solutions identified can be implemented in the same buildings under the same circumstances. The universities of Majmaah and Philadelphia have buildings with similar infrastructure. The system was applied to the buildings at Philadelphia University. The results were generalized to both universities. After implementation, the energy consumption of the EEMS using WSAN (based on the monitoring was reduced up to 23% when compared to that of the initial state.

Deck inclination and vertical displacements are among the most important technical parameters to evaluate the health status of a bridge and to verify its bearing capacity. Several methods, both conventional and innovative, are used for structural rotations and displacement monitoring; no one of these does allow, at the same time, precision, automation, static and dynamic monitoring without using high cost instrumentation. The proposed system uses a common laser pointer and image processing. The elastic line inclination is measured by analyzing the single frames of a HD video of the laser beam imprint projected on a flat target. For the image processing, a code was developed in Matlab® that provides instantaneous rotation and displacement of a bridge, charged by a mobile load. An important feature is the synchronization of the load positioning, obtained by a GNSS receiver or by a video. After the calibration procedures, a test was carried out during the movements of a heavy truck maneuvering on a bridge. Data acquisition synchronization allowed to relate the position of the truck on the deck to inclination and displacements. The inclination of elastic line was obtained with a precision of 0.01 mrad. The results demonstrate the suitability of the method for dynamic load tests, control and monitoring of bridges.

In the present work, a portable device system applied in the detection and classification of different metallic ions was proposed and developed, aiming at its application in the monitoring of hydrological systems like rivers, lakes and groundwater. Considering the system features, a portable colorimetric system was developed by using a multispectral optoelectronic sensor. All the technology of quantification and classification of metallic ions using Optoelectronic Multispectral sensors was fully integrated in the embedded hardware FPGA technology and software based on virtual Instrumentation (NI LabView ®). The system was used as a colorimeter by using the chromogen reagent of 1-(2-pyridylazo)-2-naphthol (PAN) as an indicator and the results obtained together with the signal processing and pattern analysis using the method of the linear discriminant analysis, allowed to obtain excellent results in detection and classification of Pb(II), Cd(II), Zn(II), Cu(II), Fe(III) and Ni(II) ions, with almost the same level of performance in relation to those obtained from the UV-VIS spectrometers of high spectral resolution.

Outdoor lighting is becoming increasingly widespread, and residents are suffering from serious light pollution as a result. Residents’ awareness of their rights to protection has gradually increased. However, due to the sometimes-inaccessible nature of residential vertical light incidence intensity data and the high cost of obtaining specific measurements, there is no appropriate hierarchic compensation for residents suffering from different degrees of light pollution. It is therefore important to measure light pollution levels and their damage at the neighborhood scale to provide residents with basic materials for proper protection and to create more politically suitable solutions. This article presents a light pollution assessment method that is easy to perform, is low-cost, and has a short data-processing cycle. This method can be used to monitor residential zone light pollution in other cities. We chose three open areas to test the spatial variation pattern of light intensity. The results are in accordance with spatial interpolation patterns and can be fit, with high precision, using the IDW method. This approach can also be used in 3 dimensions to quantitatively evaluate the distribution of light intensity distribution. We use a mixed-use zone in Beijing known as The Place as our case study area. The vertical illumination at the windows of residential buildings ranges from 2 lux to 23 lux; the illumination in some areas is far higher than the value recommended by CIE. Such severe light pollution can seriously interfere with people's daily lives and has a serious influence on their rest and health. The results of this survey will serve as an important database to assess whether the planning of night-time lighting is scientific and whether it provides residents with a basis for the protection of their rights.

Today electricity is distributed to the individual users via physical Copper connections. From the power stations, the energy is transported through transmission lines where the electricity, sinusoidally modulated at a fixed frequency of about 50 Hz, is raised up to a voltage in a range approximately variating between 30, and 110 kV. When electrons, aligned at this voltage, pass through the transmission lines, they cause coherent vibrations, sometimes even audible in the acoustic frequencies. In the spectrum of movements to which electric cables are subjected, there are also unexpected and sporadic movements caused by winds and rain. The problem of carrying out persistent, precise and spatially distributed monitoring of transmission line health is to use a large number of sensors physically distributed everywhere and somehow transmit the results to a control station. The use of synthetic aperture radar (SAR) data could be a viable solution of persistent and wide-area high-voltage vibration monitoring. In this paper we produce a comprehensive survey on how to monitor both movements in terms of vibrational displacement, due to weathering, and those due to electricity transmission, normally fixed at about 50 Hz. The results demonstrate the technical feasibility of an operational use of SAR for these purposes in the very short term. This would allow the possibility of monitoring malfunctions such as black-outs or other frequency anomalies.