Keywords: Wall-like RC columns; Strengthening; FRP; NSM rebars; Steel plates; Testing; FE modeling; Preloading.

The paper presents a new conception of quasi-distributed sensor for simultaneous measurement of several physical fields and the results of an experimental study of this sensor. A distinctive feature of the sensor defined by the sensitive RC elements connected in the original tree-like structure. The proposed is the structure of the sensor and measurement system as well as corresponding measurement algorithm. The high accuracy demonstrated by the sensor’s prototype gives possibility to effective use the proposed sensors in many technical and scientific applications.

The response of structures under pulse-like ground motions is characterized by the large amount of energy input in a few cycles. Consequently, structures with insufficient strength may suffer severe damage owing to excessive deformation. In a previous paper, the energy-based prediction procedure for the peak and cumulative response of a reinforced concrete (RC) frame building with steel damper columns was proposed (Fujii and Shioda, 2023). Although this procedure was verified by comparison to the nonlinear time-history analysis (NTHA) results, the performance of the proposed procedure with pulse-like ground motion records has not been verified yet. In this study, the accuracy of the energy-based prediction procedure for an RC frame building with steel damper columns was investigated by considering pulse-like ground motions. The numerical analysis results reveal that the accuracy of the predicted peak response is satisfactory, which agrees with the results of the author’s previous study. However, the accuracy of the predicted total input energy to the building model depends on the ratio of the pulse period of the ground motion to the effective fundamental period of the building model. The reasons for this underestimation of the total input energy are discussed in this paper.

The prefabricated ECC/RC combined shear wall structure is an innovative prefabricated composite structure with better seismic performance by using ECC materials with better ductility in the main force and energy consumption regions of the prefabricated reinforced concrete (RC) shear wall structure. The key factors controlling the seismic energy dissipation capacity of this kind of structure are the use regions of ECC in composite coupling beams, use regions of ECC in shear walls, strength of ECC, stirrup ratio of coupling beams, strength of longitudinal reinforcement and so on. The parameters affecting seismic energy consumption are quantified by the finite element analysis method. By comparing and analyzing the load-displacement curves, hysteresis curves, energy dissipation capacity and stiffness degradation of the prefabricated ECC/RC combined shear wall structure specimen under these parameters, it is proposed that the best use regions of ECC is the cast-in-situ zone of the coupling beams with the scope of no more than400 mm at the shear walls’ bottom. The strength grade, the strength grade of longitudinal reinforcement, and the stirrup ratio of coupling beams are suggested design as E40, HRB400 and 0.5%, respectively.

Background: Functional restoration of abdominal wall defects represent one of the fundamental challenges of reconstructive surgery. Synthetic grafts or crosslinked animal-derived biological grafts are characterized by significant adverse reactions, which are mostly observed after their implantation. The aim of this study was to evaluate the efficacy of the decellularization protocol to produce a completely acellular full-thickness abdominal wall scaffold. Methods: Full-thickness abdominal wall samples were harvested from Wistar rats and submitted to a 3 cylce decellularization process. Histological, biochemical and DNA quantification analyses were applied to evaluate the effect of the decellularization protocol. Mechanical testing and immunogenicity assessment were also performed. Results: Histological, biochemical and DNA analysis results showed the efficient decellularization abdominal wall samples after the 3rd cycle. Decellularized abdominal wall scaffolds were characterized by good biochemical and mechanical properties Conclusion: The data presented herein confirm the effective production of rat-derived full-thickness abdominal wall scaffold. Expanding this approach will allow the exploitation of the capacity of the proposed decellularization protocol in producing acellular abdominal wall scaffolds from larger animal models or human cadaveric donors. In this way, the utility of biological scaffolds with preserved in vivo remodelling properties may be one step closer to its application in clinical studies.

Lizards in Bulgaria hibernate in winter. Yet, individuals of many species were found active in this period. Cases of winter activity of Podarcis muralis and P. erhardii in the country have been published, but this behavior has not been studied in detail. The purpose of this research was to observe and analyze the winter activity of these two species in the city of Blagoevgrad. The observations took place at two sites in days with high solar radiation in December, January, and February 2015–2017. One of the sites was a typical urban territory, inhabited only by P. muralis. The other site was a suburban area, inhabited by P. erhardii. The number of the active individuals of the Common Wall Lizard recorded was about 8.5 times higher than that of the Erhard's Wall Lizard. The lowest air temperature at which P. muralis was observed was -4°C and for P. erhardii it was +0.5°C. Individuals of both species were registered only at positive substrate temperatures. Representatives of all age groups of P. muralis were recorded often with dorsoventrally flattened bodies while basking. On the other hand, few juveniles of P. erhardii were found active and they flattened their bodies very rarely.

Six Half-ring with varying linewidth from 120nm to 370nm were connected in series on five corners. The magnetization reversal processes were investigated by the measurement of anisotropic magnetoresistances (AMR). The number of switching jumps in the AMR loops, from zero to five, varied with the longitudinal applied field. These discrete jumps result from domain wall nucleating and depinning on the corners. The larger external field applied the fewer number of jumps in the MR curve. This reproducible and particular-respondence of domain wall device in pattern of half-ring wire might be the new promising magnetoelectronic devices.

Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

The Cancer Genome Atlas (TCGA) has classified papillary thyroid carcinoma (PTC) into indolent RAS-like and aggressive BRAF-like based on its distinct driver gene mutations. This study aimed to assess clinicopathology and pERK1/2 expression variations between BRAF-like and RAS-like PTCs and establish predictive models for BRAFV600E and RAS-mutated PTCs. A total of 222 PTCs underwent immunohistochemistry staining to assess pERK1/2 expression and Sanger sequencing to analyze the BRAF and RAS genes. Multivariate logistic regression was employed to develop prediction model. Independent predictors for the BRAFV600E mutation include a nuclear score of 3, the absence of capsules, an aggressive histology variant, and pERK1/2 levels exceeding 10% (X2=0.128, P>0.05, AUC=0.734, P<0.001). RAS mutation predictive model includes follicular histology variant and pERK1/2 expression >10% (X2=0.174, P>0.05, AUC=0.8, P<0.001). We proposed using the prediction model concurrently with four potential combination group outcomes. PTC cases included in combination of low BRAFV600E-scoring group and high RAS-scoring group are categorized as RAS-like (adjOR=4.857, P=0.01, 95% CI=1.470-16.049). PTCs included in combination of high BRAFV600E-scoring group and low RAS-scoring group are categorized as BRAF-like PTCs (adjOR=3.091, P=0.001, 95% CI=1.594-5.995). The different prediction models indicate variations in biological behaviour between BRAF-like and RAS-like PTCs, necessitating adjustments in treatment approaches.

Watermelon fruits of different ploidy exhibit significant variations in texture. In order to investigate the primary factors influencing texture differences, this study was conducted to investigate the differences in fruit texture development using homozygous autogamous diploid (2X)lines and their autotriploid (3X) and autotetraploid (4X) lines 'Yixuan'. The research encompassed fruit development, flesh texture profile analysis (TPA), flesh cell wall polysaccharide content, and flesh cell microstructure analysis, specifically in 2X, 3X, and 4X watermelon fruits.The results showed that as watermelon fruits matured, several characteristics exhibited an ascending trend, including fruit weight, TSS (total soluble solids) content, rind hardness, flesh cell size, and cell wall polysaccharide contents such as crude fiber, cellulose, hemicellulose, lignin, and protopectin. Conversely, the flesh texture parameters and soluble pectin content of the flesh cell wall gradually declined. Notably, significant differences in fruit flesh texture and flesh cell structure were observed among fruits of different ploidy at the 32d. Specifically, 2X fruits displayed considerably lower rind hardness, reduced flesh texture (Hardness, Fracturability, Chewiness, Gumminess), and cell density compared to 3X and 4X fruits. Additionally, 2X fruits exhibited larger cell sizes than 3X and 4X fruits. However, no significant differences were observed in the content of flesh cell wall polysaccharide contents across various ploidy levels.These findings suggested that the variation in texture among watermelon fruits of different ploidy can be attributed to the size and arrangement of flesh cells. Importantly, this research provided a foundation for further exploration of the intrinsic regulatory factors and molecular mechanisms contributing to texture variation in polyploid watermelon fruits.

Rammed earth in a built environment has vapor diffusion characteristics and humidity control ability each of which are respectively attributed to the porous structures and the hydrophilic properties. Indeed, these structures and properties, which allows easily absorbing water parti-cles, hence, affecting the durability of a rammed earth wall. This paper presents the water repel-lency method for rammed earth walls which synthesizes siloxane copolymers containing fluo-rine. The water-repellent properties are investigated by measuring the contact angle, water ab-sorption rate, and compressive strength after spray coating with the synthesized siloxane co-polymers on the surface of the rammed earth specimens under study. The water contact angle of the specimen coated with a siloxane copolymer containing 10 mol.% of a silane monomer with a fluorine group is about 140o. The water absorption of the specimen obtained after immersing in water for 24 hours is low at about 3.5 wt.%. In addition, the compressive strength is remained more than 80% of the corresponding strength of the specimen which is not immersed into water. It is confirmed that the use of a 10% by volume of the siloxane copolymer containing the fluo-rine group may assure the water-repellent performance and the economic competitiveness.

Background: Abdominal wall hernias are a common condition that is seen in daily general surgery patients. However, still more researches are needed to be conducted regarding hernias. The aim of this study is to see the prevalence of hernias among patients admitted to the Department of Surgery of a tertiary care center. Methods: A descriptive cross-sectional study was performed among patients who admitted to the department of surgery in a tertiary care center between 1 August 2023 and 20 September 2023. All patients data were extracted to an excel sheet. Results: We had 760 patients who visited in this period. Only 272 patients (27.9 %) were diagnosed with hernias. We found 52.6 % of patients were male and 47.4 % of patients were female. The age between 46- 60 years old was the most to have hernias (97 patients). Inguinal hernias were the common among other types. Diabetes mellitus, hypertension, COPD, and hydrocele were found in 10.7 % of all patients. Conclusion: The prevalence of hernias in this study was nearly to other studies that conducted in the same conditions. Early diagnosis and patient’s education are the corner stone to prevent morbidities and mortalities.

Mycobacterium tuberculosis is the agent of tuberculosis, one of the most important infectious diseases in the world. This microorganism stands out from other bacteria, not only for its extremely high infection capacity, but also for its cellular characteristics that include an extremely resistant and hydrophobic cellular parade the passage of antibiotics. An incredible ability to adapt to adverse conditions inside the host as well as its vast arsenal of virulence factors that allow its survival within the inhospitable environment within the macrophage can be highlighted. This review aims to discuss several aspects of MTB microbiology, genetics, and physiology. We will address in this review details of the metabolism of MTB that allows it to replicate in the active phase and remain viable during latency, as well as the characteristics of its cell wall that contribute to the blockade of the immune response and its resistance to antibiotics.

Since Darwin’s “Power of movement in plants” the precise mechanism of oscillatory plant growth remains elusive. Hence the search continues for the hypothetical growth oscillator that regulates a huge range of growth phenomena ranging from circumnutation to pollen tube tip growth and stomatal movements. Oscillators are essentially simple devices with few components. A universal growth oscillator with only four major components became apparent recently with the discovery of a missing component, notably arabinogalactan glycoproteins (AGPs) that store dynamic Ca2+ at the cell surface. Demonstrably, auxin-activated proton pumps, AGPs, Ca2+ channels and auxin efflux “PIN” proteins, embedded in the plasma membrane, combine to generate cytosolic Ca2+ oscillations that ultimately regulate oscillatory growth: Hechtian adhesion of the plasma membrane to the cell wall and auxin-activated proton pumps trigger the release of dynamic Ca2+ stored in periplasmic AGP monolayers. These four major components represent a molecular PINball machine a strong visual metaphor that also recognizes auxin efflux “PIN” proteins as an essential component. Proton “pinballs” dissociate Ca2+ ions bound by paired glucuronic acid residues of AGP glycomodules, hence reassesses the role of proton pumps. It shifts the prevalent paradigm away from the recalcitrant “acid growth” theory that proposes direct action on cell wall properties, with an alternative explanation that connects proton pumps to Ca2+ signaling with dynamic Ca2+ storage by AGPs, auxin transport by auxin-efflux PIN proteins and Ca2+ channels. The extensive Ca2+ signalling literature of plants ignores arabinogalactan proteins (AGPs). Such scepticism leads us to reconsider the validity of the universal growth oscillator proposed here with some exceptions that involve marine plants and perhaps the most complex stress-test, stomatal regulation.

A fundamental question in biology is how cell shapes are genetically encoded and enzymatically generated. Prevalent shapes among walled bacteria include spheres and rods. These shapes are chiefly determined by the peptidoglycan (PG) cell wall. Bacterial division results in two daughter cells, whose shapes are predetermined by the mother. This makes it difficult to explore the origin of cell shapes in healthy bacteria. In this review, we argue that the Gram-negative bacterium Myxococcus xanthus is an ideal model for understanding PG assembly and bacterial morphogenesis because it forms rods and spheres at different life stages. Rod-shaped vegetative cells of M. xanthus can thoroughly degrade their PG and form spherical spores. As these spores germinate, cells rebuild their PG and reestablish rod shape without preexisting templates. Such a unique sphere-to-rod transition provides a rare opportunity to visualize de novo PG assembly and rod-like morphogenesis in a well-established model organism.

Worldwide, hernia repair represents one of the most frequent surgical procedures encompassing a global market valued at several billion dollars. This type of surgery usually requires the implantation of a mesh that needs the appropriate chemical, physical and biological properties for the type of repair. This review thus presents a description of the types of hernias, current hernia repair methods, and the state of the art of prosthetic meshes for hernia repair providing the most important meshes used in clinical practice by surgeons working in this area classified according to their biological or chemical nature, morphology and whether bioabsorbable or not. We emphasise the importance of surgical site infection in herniatology, how to deal with this microbial problem, and we go further into the future research lines on the production of advanced antimicrobial meshes to improve hernia repair and prevent microbial infections, including multidrug-resistant strains. A great deal of progress has been made in this biomedical field in the last decade. However, we are still far from an ideal antimicrobial mesh that can also provide excellent integration to the abdominal wall, mechanical performance, low visceral adhesion and minimal inflammatory or foreign body reactions, among many other problems.

Toll-like receptors (TLRs) play a key role in the innate immune response to numerous pathogens, including Acanthamoeba sp. The aim of this study was to determine the expression of TLR2 and TLR4 in the eyes of mice following intranasal infection with Acanthamoeba sp. Amoebae used in this study were isolated from the bronchial aspirate of a patient with acute myeloid leukemia (AML) and atypical symptoms of pneumonia. We found statistically significant differences in the expression of TLR2 and TLR4 in the eyes of immunocompetent mice at 8, 16, and 24 days post Acanthamoeba sp. infection (dpi) compared to control. Immunosuppressed mice showed significant differences in the expression of TLR2 at 16 and 24 dpi compared to uninfected animals. Our results indicate that TLR2 and TLR4 are upregulated in the eyes of mice in response to Acanthamoeba sp. We suggest that it is possible for trophozoites to migrate through the optic nerve from the brain to the eyes.

In recent years, the term quantum-like has been increasingly used in different disciplines, including neurosciences, psychological and socio-economical disciplines, claiming that some investigated phenomena show “something” in common with quantum processes and, therefore, they can be modeled using a sort of quantum formalism. Therefore, the increasing use of the term quantum-like calls for defining and sharing its meaning in order to properly adopt it and avoid possible misuse. In our opinion, the concept of quantum-like may be successfully applied to macroscopic phenomena and empirical sciences other than physics when at least two conditions are satisfied: a) the behavior of the investigated phenomena show logical analogies with quantum ones; b) it is possible to find a criterion of truth based on an experiential/scientific approach applied to a probabilistic model of description of the phenomena. This is only a first, small step in the approach to the concept of quantum-like, hopefully helpful to promote further discussion and achieve a better definition.

The envelope (façade) of a building is the first barrier between the exterior and the interior of the building and withstands the highest variation of temperature and solar radiation. Trombe walls are used to take advantage of that and contribute to the heating of interior air, helping the heating system. In this study, a new Trombe wall design is presented with the aim to contribute significantly to the ventilation of residential buildings. For this an exterior wall equipped with a proposed Trombe system was studied in a numerical simulation analysis. The proposed systems consist of two parts, the air cavities on the exterior of the wall, covered with silica glass, and another layer used for heat transfer, on the interior, comprised of a MPCLBs wall of 115mm. Two cities in Romania were considered to represent the coldest and hottest climate in Romania. Brașov representing the cold climate and Constanța representing the hot climate. In the investigation, both the presence and absence of solar radiation were taken into account. In total 4 cases were established. For all four cases monthly research was made using monthly means temperature, direct and diffuse solar radiation. The results are promising and illustrate that the system works the best during the transitional seasons of spring and autumn. The lower the outdoor temperature the higher the temperature can be increased. Overall, solar radiation accounted for an average of 2 °C increase. The temperature increase varied between 3.4 °C to 15.99 °C for Brașov and between 6.42 °C to 12.07 °C in Constanța.

The construction industry generates significant CO2 emissions, and rebar is a major contributor to this environmental impact. Extensive research has been conducted to address this issue. Recent advancements have introduced algorithms to reduce rebar waste and consumption, demonstrating the feasibility of achieving near-zero rebar cutting waste (N0RCW) by considering special-length rebars. However, conventional lap splices, the most common rebar joint method, consistently consume excessive rebar quantities despite extending beyond their mandated zones. Conversely, couplers eliminate rebar lengths required for lapping splices, reducing the usage of rebar. Applying special lengths and couplers in heavily loaded structures like diaphragm walls can significantly reduce rebar usage and cutting waste, consequently reducing CO2 emissions and associated costs. This study aims to optimize rebar consumption and sustainability in diaphragm wall structures by integrating mechanical couplers with a special-length rebar approach. A case study confirmed a substantial reduction in purchased rebar usage (17.95% and 5.38%) and carbon emissions (15.24% and 2.25%) compared to the original design and previous study, respectively. Broadly implementing the proposed method across various buildings and infrastructure projects could further multiply these benefits, fostering the achievement of SDGs adopted by the United Nations for sustainable construction.

A 17th century wall painting representing a Virgin between two Saints in a noble Italian renaissance palace, Palazzo Gallo in Bagnaia (Viterbo, Italy), was restored in 2021 in the context of a wider restoration campaign interesting the main room of the palace built by cardinal Sansoni Riario. Diagnostic analyses done with traditional characterization techniques (optical microscopy on micro-stratigraphic sections, X-ray fluorescence spectroscopy and Fourier transform infrared spectroscopy) provided the identification of both original painting and restoration materials, while imaging investigations as ultraviolet fluorescence photography, false color images and multispectral mapping provided by hypercolorimetric multispectral imaging (HMI) technique enabled the evaluation of the state of conservation, locating restoration interventions and supporting the monitoring of the cleaning procedure. An altered protective Paraloid-based coating dating from early 2000s had to be removed due to the unpleasant glossy finishing given to the painted surface, making the scene barely readable. To pursue a restoration protocol based on environmental sustainability and green chemistry, enzyme-based gels marketed by Nasier-Brenta© and CTS© companies were tested in different protocols for the cleaning of the mash covering the painting. Although some interesting results were observed, the enzymatic cleaning had a scarce effectiveness with timing beyond a reasonable interval. Traditional chemical solvents as Dowanol PM (methoxy-propanol) and benzyl alcohol were necessary to complete the cleaning of the painting surface.

The A. japonicus industry has expanded significantly, but no research has focused on how to de-termine the age of A. japonicus during farming. Correctly estimating the age of A. japonicus can provide a decision-making basis for the breeding process, and data for the protection of A. japonicus aquatic germplasm resources. DNA methylation levels in the body wall of Apostichopus japonicus at 4 months, 1 year, 2 years, and 3 years old were determined by MethylRAD-Seq, and differentially methylated genes related to age were screened. The results of the study found that 441 and 966 differentially methylated genes were detected at CCGG and CCWGG sites, respectively. As-partate aminotransferase, succinate semialdehyde dehydrogenase, isocitrate dehydrogenase, the histone H2AX, heat shock protein Hsp90, aminopeptidase N, cell division cycle CDC6, Ras GTPase activating protein (RasGAP), slit guidance ligand slit 1, integrin linked kinase ILK, mechanistic target of rapamycin kinase Mtor, protein kinase A Pka, and autophagy-related 3 atg3 these genes may play key roles in the growth and aging process of A. japonicus. This study provided data for identifying the age of A. japonicus.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

The aim of this study is to test the effectiveness and safety of AE-AE surgery combining otoendoscopy and surgical microscopy in the treatment of acquired pars flaccida cholesteatoma in stages Ib and II of the Japan Otological Society classification occupying the tympanic cavity and attic. A historical cohort study on 65 patients. Of the total, 44 patients were treated by AE-AE surgery using an otoendoscope and 21 with canal wall-up tympanomastoidectomy (CWUT). Patients in whom the AE-AE technique was performed had a lower recurrence rate (9%) compared to those treated with CWUT (38%); p=0.013. In addition, the median time to recurrence was lower in the AE-AE group (4 years [P25-75= 1.25-2-75]) than in CWUT group (2 years [P25-75= 3.25-4.75]); p=0.048. Thresholds were higher in the CWUT group compared to the AE-AE group in pre-surgery (53±16 vs 44±15; p=0.039) and post-surgery (52±18 vs 42±16 dB dB; p=0.042), but not in pre-post-surgery comparisons neither in the AE-AE technique (p= 0.89) nor in the CWUT technique (p= 0.96). We concluded that AE with otoendoscopic support is an effective and safe technique for acquired cholesteatomas occupying box and attic in stages IB and II.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

This study was conducted to improve the white index (WI) by preparing thermally expandable microspheres (TEMs) for wallpaper. The thermal properties, foam expansion ratio and WI were studied depending on the particle size of colloidal silica in the preparation of TEMs. As a result, the TEMs with small particles of colloidal silica showed the best results for whiteness and yellowing. Additionally, TGA results indicated that it was highly possible that colloidal silica with small particle sizes was physically or chemically attached to the surface of the TEMs that led to an improvement in whiteness at high temperatures.

Photodynamic inactivation (PDI) combines the nontoxic photosensitizer (PS) and visible light to generate reactive oxygen species (ROS), which can cause oxidative damages in (on) microbial organisms. Previously, we have shown that chitosan can augment the bactericidal efficacy mediated by PDI against bacteria and Candida. In this study, we showed that the antimicrobial action of chitosan to augment PDI relates to the enlargement of cell surface destruction. The microbial cell surfaces exhibit severe irregular shapes after PDI in the presence of chitosan. Furthermore, increase in the concentrations or incubation time of chitosan significantly reduce the amounts of photosensitizers TBO required, indicating that chitosan could be a synergistic agent with PDI against human pathogens. A prolonged lag phase was found in PDI surviving microbial cells, in which chitosan can act to synergistically eradicate the cells. Once the impaired cells rebuild their cellular functions from PDI-induced damage, the increased cytotoxic effect of chitosan disappeared. Together, our results suggest that chitosan with an augmented bactericidal activity after PDI is to inhibit the rehabilitation of PDI surviving cells, leading to microbial death.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

After screening nearly 1000 synthetic peptides, a synthetic peptide termed JAL-AK22 (KYEGHWYPEKPYKGSGFRCIHI) derived from the BoxA domain in Tob1 protein was found to activate both unfolded and folded proMMP-7. In addition, JAL-AK22 showed auto-proteolytic activity. Interestingly, the smaller derivative of JAL-AK22 termed JAL-TA9 (YKGSGFRMI) also possessed auto-proteolytic activity and cleaved 2 fragment peptides (MMP18-33 and MMP18-40) derived from the prodomain of proMMP-7 under physiological conditions. These proteolytic activities were inhibited by AEBSF, a serine protease inhibitor. Our results demonstrate that a small synthetic peptide consisting of only 9 amino acids has serine protease-like activity and activates proMMP-7 by cleaving the prodomain region. We thus propose calling small peptides possessing with protease-like activity Catalytides (catalytic peptides). We expect that our findings will stimulate the development of novel Catalytides and related applications.

Tissue engineered heart valves can grow, repair, and remodel after implantation, presenting a more favorable long-term solution compared to mechanical and porcine valves. Achieving functional engineered valve tissue requires the maturation of human cells seeded onto valve scaffolds under favorable growth conditions in bioreactors. The mechanical stress and strain on developing valve tissue caused by different pressure and flow conditions in bioreactors are currently unknown. The aim of this study is to quantify the wall shear stress (WSS) magnitude in heart valve prostheses under different valve geometries and bioreactor flow rates. To achieve this, the study used fluid-structure interaction simulations to obtain the valve's opening geometries during the systolic phase. These geometries were then used in computational fluid dynamics simulations with refined near-wall mesh elements and ranges of prescribed inlet flow rates. The data obtained included histograms and regression curves that characterized the distribution, peak, and median WSS for various flow rates and opening configurations. The study also found that the upper region of the valve near the commissures experienced higher WSS magnitudes than the rest of the valve.

The centrifugal force field in the hydrocyclone was affected by the concave-wall curvature radius R0, the mechanism of droplet deformation was closely related to the mass transfer efficiency. Numerical simulation and experimental data were collected to reveal the deformation characteristics and mechanism of single droplet crossing concave-wall jet. Normalized interfacial energy γ and stretching performance were provided to investigate the droplet deformation process. The results showed that the droplet was stretched along the streamwise and shrank along the spanwise in the concave-wall jet. The droplet interfacial energy and deformation were the largest when the droplet crossed the jet boundary at t = 0.20 s. Maximum γ value increased with the increase of R0 by 57.3% to 71.4%, and the distance between droplet and concave-wall increased with R0. Q-criterion was exported to show the vortex strength increasing as the decrease of R0 in the jet boundary. The pressure distribution inside the droplet showed that the pressure decreased as R0 increased, while the pressure difference increased along the streamwise and wall-normal direction. The study suggested that the droplet breakup was more difficult for the smaller R0, which was beneficial for liquid-liquid heterogeneous separation.

Candida tropicalis, an opportunistic pathogen, ranks among the primary culprits of invasive candidiasis, a condition notorious for its resistance to conventional antifungal drugs. The urgency to combat these drug-resistant infections has spurred the quest for novel therapeutic compounds, with a particular focus on those of natural origin. In this study, we set out to evaluate the impact of Isoespintanol (ISO), a monoterpene derived from Oxandra xylopioides, on the transcriptome of C. tropicalis. Leveraging transcriptomics, our research aimed to unravel the intricate transcriptional changes induced by ISO within this pathogen. Our differential gene expression analysis unveiled 186 differentially expressed genes (DEGs) in response to ISO, with a striking 85% of these genes experiencing upregulation. These findings shed light on the multifaceted nature of ISO's influence on C. tropicalis, spanning a spectrum of physiological, structural, and metabolic adaptations. The upregulated DEGs predominantly pertained to crucial processes, including ergosterol biosynthesis, protein folding, response to DNA damage, cell wall integrity, mitochondrial activity modulation, and cellular responses to organic compounds. Simultaneously, 27 genes were observed to be repressed, affecting functions such as cytoplasmic translation, DNA damage checkpoints, membrane proteins, as well as metabolic pathways like trans-methylation, trans-sulfuration, and trans-propylamine. These results underscore the complexity of ISO's antifungal mechanism, suggesting that it targets multiple vital pathways within C. tropicalis. Such complexity potentially reduces the likelihood of the pathogen developing rapid resistance to ISO, making it an attractive candidate for further exploration as a therapeutic agent. In conclusion, our study provides a comprehensive overview of the transcriptional responses of C. tropicalis to ISO exposure. The identified molecular targets and pathways offer promising avenues for future research and the development of innovative antifungal therapies to combat infections caused by this pathogenic yeast.

It is generally accepted that the human abdominal wall is comprised of skin, subcutaneous tissues, muscles and their aponeuroses, and the parietal peritoneum. Understanding these layers and their mechanical properties provides valuable information to those designing procedural skills trainers, supporting surgical procedures (hernia repair), and engineering-based work (in silico simulation). However, there is little literature available on the mechanical properties of the abdominal wall in layers or as a composite. This work characterizes the tensile properties of the human abdominal wall by layer and as a partial composite. Tissues were collected from fresh-never-frozen and fresh-frozen cadavers and tested in uniaxial tension at a rate of 5 mm/min until failure. Stress-strain curves were created for each sample, and the values for elastic moduli, ultimate tensile strength, and strain at failure were obtained. The experimental outcomes from this study demonstrated variation of tensile properties within and between tissues. The data also suggest that the tensile properties of composite abdominal walls are not additive. Ultimately, this body of work contributes to a deeper comprehension of these mechanical properties and will serve to enhance patient care, refine surgical interventions, and assist with more sophisticated engineering solutions.

In recent years, with the increase in maritime trade, the necessity of increasing the capacities of the ports has emerged. However, while it is planned to increase the capacities of the ports, it is important that the port continues to operate at the same time. In this respect, the old port structures should not be damaged during the capacity increase. In this study, the strengthening of a port in Guinea is discussed as a case study. In the study, the existing quay wall was evaluated, and geotechnical and structural alternatives of the new structure to be built for capacity increase were evaluated. A combined system was designed as a pile foundation and a reinforced foundation with plastic piles so as not to damage the existing quay wall. The pile capacities obtained as a result of the analyses were verified by loading tests.

The present study provides new insights into the growth of brown algal cell wall by showing that cell wall polysaccharide plays an important role in the process of growth consider- ing the physicochemical characteristic of young and old Cladosiphon okamuranus. To determine its structural variation in detail, the cell wall was sequentially fractionated into five fractions: hot water (HW), ammonium oxalate, hemicellulose-I (HC–I), HC-II, and cellulose, and analyzed physicochemically. Results showed that almost 80% of the total recovery cell wall from both young and old thalli was HW and HC-I contained mainly fucoidan composed of Fuc, GlcA, and sulfate in molar ratios of 1.0: 0.3: 0.6~0.7 and 1.0: 0.3: 0.2~0.3, respectively. Fucoidan in HW was a highly sulfated matrix polysaccharide abundance in young thalli, while fucoidan in HC-I was rich in old thalli and functions as hemicellulose in land plants, crosslink with cellulose and strengthen the cell wall. We found that HW and HC-I were particularly involved in the growth and strength of old thalli appeared to be due to the deposition of HC-I and reducing of water content during the growth process.

The most common method for establishing bioequivalence (BE) is to demonstrate similarity of concentration-time profiles in the systemic circulation, as a surrogate to the site of action. However, the similarity, or otherwise, of profiles from two different formulation in the gastrointestinal tract (GIT) may not be associated with same conclusions based on systemic circulation. Here, we have explored the concordance of BE conclusions (or otherwise) for a set of hypothetical formulations based on drug concentration-profiles in various segments of gut vs those in systemic circulation using virtual trials powered by physiologically-based (PBPK) models. Moreover, by changing physiological and biological attributes of the GIT, the impact of Crohn’s Disease on the BE conclusions was explored. The virtual BE (VBE) was applied to an Entocort EC, a pH/time-dependent release formulation of budesonide, as model drug that is targeted at ileum and colon. Substantial “discordance” between the local and systemic outcomes of VBE was observed. Upper GIT segments were much more sensitive to formulation changes than systemic circulation, where the latter led to false conclusions for BE. The ileum and colon showed a lower frequency of discordance with systemic-derived VBE. Nonetheless, a higher f2 value than the default similarity standard (50) was required to achieve local BE. In the case of Crohn’s Disease, a product-specific f2 value might be needed for drugs such as Entocort EC to ensure local BE, knowing the insensitivity of systemic data to show lack of BE. The results, being limited to the single model drug product, Entocort EC, may not provide a a general and conclusive picture. However, for the first time, it demonstrated the potential discordances between the local gut vs systemic BE.

Common bean has received attention as a model plant for legume studies, but little information is available about the morphology of its pods and the relation of this morphology to loss of seed dispersal and/or the pod string, which are key agronomic traits of legume domestication. Dehiscence is related to pod morphology and the anatomy of pod tissues because of the weakening of the dorsal and ventral dehiscence zones and the tensions of the pod walls. These tensions are produced by the differential mechanical properties of lignified and non-lignified tissues and changes in turgor associated with fruit maturation. In this research, we histologically studied the dehiscence zone of the ventral and dorsal sutures of the pod in two contrasting genotypes for dehiscence and string, by comparing different histochemical methods with autofluorescence. We found that the secondary cell wall modifications of the ventral suture of the pod were clearly different between the dehiscence-susceptible and stringy PHA1037 and the dehiscence-resistant and stringless PHA0595 genotypes. The susceptible genotype had cells of bundle caps arranged in a more easily breakable bowtie knot shape. The resistant genotype had a larger vascular bundle area and fibre cap cells (FCCs), and due to their thickness, the external valve margin cells were significantly stronger than those from PHA1037. Our findings suggest that the FCC area, and the cell arrangement in the bundle cap, might be a partial structure involved in the pod dehiscence of common bean. The autofluorescence pattern at the ventral suture allowed us to quickly identify the dehiscent phenotype and gain a better understanding of cell wall tissue modifications that took place along the bean's evolution, which had an impact on crop improvement. We report a simple autofluorescence protocol to reliably identify secondary cell wall organization and its relationship to dehiscence and string in common bean.

This paper presents a low-cost C-band frequency-modulated continuous wave (FMCW) radar system for use in indoor through-wall metal detection. Indoor remote-sensing applications, such as through-wall detection and positioning, are essential for the comprehensive realization of the internet of things or super-connected societies. The proposed system comprises a two-stage radio-frequency power amplifier, a voltage-controlled oscillator, circuits for frequency modulation and system synchronization, a mixer, a 3-dB power divider, a low-noise amplifier, and two cylindrical horn antennas (Tx/Rx antennas). The antenna yields gain values in the 6.8 ~ 7.8 range when operating in the 5.83 ~ 5.94 GHz frequency band. The backscattered Tx signal is sampled at 4.5 kHz using the Arduino UNO analog-to-digital converter. Thereafter, the sampled signal is transferred to the MATLAB platform and analyzed using a customized FMCW radar algorithm. The proposed system is built using commercial off-the-shelf components, and it can detect targets within a 56.3 m radius in indoor environments. In this study, the system could successfully detected targets through a 4-cm-thick ply board with a measurement accuracy of less than 10 cm.

The study utilizes the energy-flux-vector method to analyze the heat transfer characteristics of natural convection in a wavy-wall porous square cavity with a partially-heated bottom surface. The effects of the modified Darcy number and modified Rayleigh number on the energy-flux-vector distribution and mean Nusselt number are examined. The results show that when a low modified Darcy number with any value of modified Rayleigh number is given, the recirculation regions are not formed in the energy-flux-vector distribution within the porous cavity. Therefore, a low mean Nusselt number is obtained. The recirculation regions do still not form and thus the mean Nusselt number has a low value when a low modified Darcy number with a high modified Rayleigh number is given. However, when the values of the modified Darcy number and modified Rayleigh number are high, the energy flux vectors generate recirculation regions and thus a high mean Nusselt number is obtained.

A numerical study of the flow over a NACA aerofoil is presented in this paper. The numerical simulations are achieved with the computer code CFX and the computational domain is created by the computer tool ANSYS ICEM CFD. The CFX code is based on the finite volume method to solve the equations of mass, momentum and energy. The purpose of this paper is to determine the pressure distribution, flow patterns and the forces acting on the airfoil. Effects of the attack angle and Reynolds number on the velocity and pressure distribution, on the lift and drag coefficients are also explored.

The study examines the behavior of the Mechanically Stabilized Earth (MSE) wall using available reinforcement materials in Danang, Vietnam. The MSE was reinforced by the self-fabricated galvanized steel grids using CB300V steel with 3 cm ribs. The backfill soil is a sandy clay soil from the local area with a low cohesion. A full-scale model with full instrumentation was installed to investigate the distribution of tensile forces along the reinforcement layers. The highest load that caused the wall to collapse due to internal instability (reinforcement rupture) was 302 kN/m2, which is 15 times the design load of 20 kN/m2. The failure surface within the reinforced soil had a parabolic sliding shape which is similar to the theoretical studies. At the failure load level, the maximum lateral displacement at the top of the wall facing was small (3.9 mm) which is significantly lower than the allowable displacements for the retaining wall. Furthermore, a numerical model using FLAC software was applied to simulate the performance of the MSE wall. The modeling results are in good agreement with the physical model. Thus, the self-fabricated galvanized steel grids could be confidentially used in combination with the local backfill soil for the MSE walls.

This paper studies the dynamic response of corner supported modular steel buildings with a core wall system, under progressive collapse scenarios, associated with corner module removals. Since using secondary systems such as concrete core in mid- to high-rise buildings is currently una-voidable, understanding their impact on load transfer between modules during collapse scenarios becomes essential. The designated buildings with four-, eight- and twelve-story were modelled using the macro-model based finite element method in Abaqus. Also, three different locations are considered for the concrete shear core within the building plan, leading to nine various case scenarios. Each vertical and horizontal inter-module connection was modelled by one axial and two shear springs with predefined nonlinear force-displacement behaviour. The local and global buckling, which plays an essential role in the building's stability, was considered to obtain accurate results. Finally, parametric studies on the building response were carried out, including the intra-module connection rigidity and inter-module connection stiffness. The results demonstrated that the core wall could maintain the robustness of modular steel building through two mechanisms dependent on its location within the plan. Also, preventing plastic hinges from forming in beams could be introduced as an anti-collapse mechanism in the corner module removal scenarios

Soil cadmium (Cd) contamination has become a serious problem in China. In this study, the goals of the field experiments were to understand how the application of nitrogen fertilizer at the full heading stage and filling stage reduced the uptake of Cd in rice by affecting the distribution of Cd in iron plaques on the root surfaces and subcellular in the root and flag leaf. The hydroponic culture experiments aimed to explore the effect of interaction or deficiency of nitrogen and cadmium on cadmium accumulation in rice at the late growth stage. The results showed that under the condition of having enough nitrogen supply during the early growth stage, applying nitrogen fertilizer during the full heading stage and filling stage resulted in a significant increase in the concentration of Fe and Cd on the root plaques at the milk stage and mature stage. Additionally, it increased the concentration and proportion of Cd in the soluble fraction of subcellular in the flag leaves at the milk stage. On the other hand, when there was a deficiency of nitrogen, the concentration of Fe in the root plaques increased significantly, while the concentration of Cd in the root plaques decreased significantly. Moreover, the proportion of Cd in the flag leaf cell walls increased significantly. Regardless of whether there was sufficient or deficient nitrogen supply during the early growth stage, applying nitrogen at the full heading stage reduced the Cd concentration in brown rice by 35.11% and 57.25%, respectively. Under hydroponic culture conditions with both Cd exposure and later-stage nitrogen supply significantly increased the Cd concentration in brown rice. However, in the absence of Cd, nitrogen supply significantly reduced the Cd concentration in brown rice. The accumulation of Cd in brown rice was significantly correlated with the accumulation of Fe and Mn at the late growth stage. Our findings indicate that when there is sufficient nitrogen nutrition during the early growth stage of rice, topdressing nitrogen fertilizer at the full heading stage combined with lime with mineral element fertilizers such as Fe and Mn is an effective approach to reduce the presence of cadmium in rice grains.

Amidst the strong demand for wood-based products, and the clamor of environmental consciousness, more functional and green solutions arise to meet both of these goals. Pursuant to this, the study looked into the potential of a bio-waste taken from Cocos nucifera tree known as phellem—the tree’s outermost skin made of dead tissues, to be a main component of a new construction material. This study builds on existing research showing phellem is impermeable, buoyant, elastic, has a slow burn rate, and repels water during precipitation, which supports the hypothesis that phellem may be a potential substitute material for dry wall boards. To test this, three (3) formulations were developed as experimental setups to test the physico-mechanical properties of coconut palm phellem (COPAP): Formulation A (40% COPAP and 60% cement); Formulation B ( 25% COPAP and 75% cement); and lastly, Formulation C that was (10% COPAP and 90% cement). The study tested (1) which among these formulations exhibited the best physico-mechanical properties, then it (2) compared the formulations with common dry wall products available in the market, and subsequently, (3) identified the possible architectural applications of COPAP board as a new building material. Of the three setups, Formulation C exhibited the best physico-mechanical properties in terms of compressive and flexural strength, fire resistivity, and water absorption. It fared better than the particle board in terms of compressive strength, better than wafer and particle board in fire resistivity, performed best in the water absorption test, and was almost equivalent in flexural strength to fiber cement board. With these findings, the study concluded that COPAP board can be used for projects that entail a high number of interior partitions, such as offices, BPO firms and commercial stalls in shopping malls, etc. The findings were conclusive only for interior applications, as the results clearly suggest that the COPAP boards are not load-bearing. Future investigations may explore and assess other properties of COPAP boards like thermal and sound insulation, resistance to rot and other properties that may prove its competitive advantage as a construction material.

The buildup of plaque in the arteries characterizes atherosclerosis, which causes the walls of the arteries to thicken, the lumen to narrow, and the wall to thin in certain areas. These changes can lead to alterations in blood flow, potentially resulting in aneurysms and heart attacks if left untreated. This paper presents a phenomenological model to explain the mechanics of plaque rupture in stenosed bifurcated elastic arteries. The model considers the interaction between the plaque and artery wall, blood flow, mechanical properties of the artery wall and plaque, and hemodynamic forces in the system. Using the Navier-Stokes equations to describe blood flow and elastic properties of artery walls, our study shows that blood flow can become turbulent, leading to backflow, vortices, and possible stagnation. Certain regions can become highly vulnerable and result in elevated heat transfer between blood and arterial walls, which can lead to the rupture of the plaque cap. The study focuses on blood flow features such as velocity profiles and wall displacement on fluid-structure interaction, which are consistent with the literature. Finally, we calculate the wall shear stress (WSS) for minimum and maximum times while considering elastic walls. Our findings may provide valuable insights into the mechanisms of plaque rupture and inform the development of improved diagnostic and therapeutic approaches.

Advanced manufacturing techniques, aimed at implants with high dependability, flexibility, and low manufacturing costs, are crucial in meeting the growing demand for high-quality products like biomedical implants. Incremental sheet forming is a promising flexible manufacturing approach for rapidly prototyping sheet metal components using low-cost tools. Titanium and its alloys are used to shape most biomedical implants because of its superior mechanical qualities, biocompatibility, low weight, and great structural strength. The poor formability of titanium sheets at room temperature, however, limits their widespread use. The goal of this research is to show that gradual sheet formation of a titanium biomedical implant is possible. The possibility of creative and cost-effective concepts for the manufacturing of such complicated shapes with significant wall angles is explored in this study. A numerical simulation based on finite element modeling as well as a design process tailored to metal forming is used to complete the development. The mean of uniaxial tensile tests with a constant strain rate was used to study the flow behavior of the studied material. To forecast the crack, the obtained flow behavior was modeled using the behavior model and failure model.

With the increased use of simulation based training using animal models for the education of surgical and anaesthetic techniques, an increased understanding of the anatomy of such models and how they compare to humans is required. The transversus abdominis plane block is a regional anaesthetic technique that requires an understanding of the abdominal wall anatomy along with proficient ultrasound use. The current review aims to compare the anatomy of the abdominal wall across species, particularly focussing on the pertinent differences within the class of mammals, and secondarily, it aims to address the implications of these differences for simulation based training of the transversus abdominis plane block. To achieve this, the PubMed, Web of Science and Google Scholar databases were searched for relevant literature. The mammalian abdominal wall differs in its musculature, vasculature or innervation from that of amphibians, birds or reptiles, however, among species of mammals, the structure of the abdominal wall follows a similar framework. Particular differences among mammals include the additional muscular layer of the panniculus carnosus found in most mammals other than humans, the variable arterial origins and dominant vascular supply of the abdominal wall and the number of thoracolumbar nerves innervating the abdominal wall. When using animal models for simulation based training, the pig is recommended for the transversus abdominis plane block given its closely homologous abdominal wall structure, availability and larger comparative size.

Joints between walls are very important for structural analysis of each masonry building at the global and local level. This issue was often neglected in case of traditional joints and relatively squat walls. Nowadays the issue of wall joints is becoming particularly important due to the continuous strive for simplifying structures, introducing new technologies and materials. Eurocode 6 and other standards (USA, Canadian, Chinese, and Japanese) recommend inspecting joints between walls, but no detail procedures have been specified. This paper presents our own tests on joints between walls made of autoclaved aerated concrete (AAC) masonry units. Tests included reference models composed of two wall panels joined perpendicularly with a masonry bond (6 models), traditional steel and modified connectors (12 models). A shape and size of test models and structure of a test stand were determined on the basis of the analysis of the current knowledge, pilot studies and numerical analyses of FEM. The analysis referred to the morphology and failure mechanism of models. Load-displacement relationships for different types of joints were compared and obtained results were referred to results for reference models. A mechanism of cracking and failure was found to vary, and clear differences in behaviour and load capacity of each type of joints were observed. Individual working phases of joints were determined and defined, and the empirical approach was suggested to determine forces and displacement of wall joints.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

Morphogenesis remains a riddle, wrapped in a mystery, inside an enigma. It remains a formidable problem viewed from many different perspectives of morphology, genetics, and computational modelling. We propose a biochemical reductionist approach that shows how both internal and external physical forces contribute to plant morphogenesis via mechanical stress-strain transduction from the primary cell wall tethered to the plasma membrane by a specific arabinogalactan protein (AGP). The resulting stress vector with direction defined by Hechtian adhesion sites, has a magnitude of a few picoNewtons amplified by a hypothetical Hechtian growth oscillator. This paradigm shift involves stress activated plasma membrane Ca2+channels and auxin-activated H+-ATPase. The proton pump dissociates periplasmic AGP-glycomodules that bind Ca2+. Thus, as the immediate source of cytosolic Ca2+ an AGP-Ca2+ capacitor directs vectorial exocytosis of cell wall precursors and auxin efflux (PIN) proteins. In toto these components comprise the Hechtian Oscillator and also the gravisensor. Thus interdependent auxin and Ca2+ morphogen gradients account for the predominance of AGPs. The size and location of a cell surface AGP-Ca2+ capacitor is essential to differentiation and explains AGP correlation with all stages of morphogenetic patterning from embryogenesis to root and shoot. Finally, evolutionary origins of the Hechtian Oscillator in the unicellular Chlorophycean algae reflect the ubiquitous role of chemiosmotic proton pumps that preceded DNA at the dawn of life.

The present study aimed to develop a feeding strategy for pregnant sows which involved the prenatal administration of a mixture of pancreatic-like fungal enzymes, such as lipase, amylase, and protease, at (1) 1–115 days of gestation (group D1) and (2) 80–115 days of gestation (group D2) and to carry out a comparison with groups of sows that were not receiving such supplementation (negative control [NC] and positive control [PC]). It was found that the administration of the enzyme supplement resulted in a significant shortening of gestation (P ≤ 0.01). The pancreatic enzymes administered to sows had a significant effect on the number of liveborn piglets and weaned piglets, which was higher compared to the control groups that did not receive supplementation respectively: D1-12.1±1.1 and 11.12±1.1; D2- 12.8±1.3 and 11.75±0.07 vs. control groups KN-10.7±1.0 and 9.62±0,95 and KP 10.9±1.2 and 10.15±1.0 (P<0.006). Significant changes in piglet growth were observed after weaning up to 70 days of age. During this period, the most favorable growth parameters were found in groups D2 (420±91g) and PC (407±103g), in which piglets were given a mixture of pancreatic enzymes (lipase, amylase, and protease) at 3 weeks of age, and significantly higher weight gain and feed intake were observed compared to groups NC (378±114g) and D1 (381±96g) (P ≤ 0.007). In contrast, insulin levels were significantly lower in groups D1 and D2, respectively 6,8 IU/ml and 6,7 IU/ml compared to groups NC (14,6 IU/ml) and PC (16,6 IU/ml) ( (P ≤ 0.01). Piglets in group D2 had a significantly better feed conversion ratio (FCR) 1.604±0.10 compared to the other dietary groups: KN– 1.986±0.14; KP– 1.704±0.11; D1 – 1.932±0.15 (P ≤ 0.03). Histological imaging confirmed significantly thicker intestinal epithelium and intestinal mesenteron in animals from groups D2 and PC (P ≤ 0.03). Animals from the groups KP, D1 and D2 receiving enzymes showed a highly significant increase in the surface area of pancreatic follicles and pancreatic surface area compared to the group without KN supplementation (P<0.01). Furthermore, significantly higher activity of the brush border enzyme lactase was observed in groups D1; D2 and PC compared, respectively 32.90±3.99; 30.00±6.83 and 29.60±29.60 to group NC – 21.80± 3.27 (P ≤ 0.01).

Recent researches indicated that metal nanoparticles which have the unique optical properties can be used to enhance the spectral response of the photovoltaic modules. Since most of the nanoparticles have enhancement effects in a specific wavelength range, improving the spectral response of the photovoltaic modules in a broadband range is crucial for their applications in imaging, energy harvesting, and optical communication. In this study, flower-like silver particles are applied to achieve the enhancement effects in a broadband range. The optical absorption of photovoltaic modules is improved in a broad wavelength range of 400~2000 nm by immobilizing flower-like silver particles onto an amorphous Si p-i-n structure, and the peak responsivity of the spectral response is enhanced by about 10 times. Theoretical investigation further elaborates that the enhancement originates from the near-field effects of silver particles due to the interaction of different parts of the flower-like silver particles. Through these studies, we demonstrate that, utilizing the subwavelength silver particles with roughness surface can achieve the spectral response of the photovoltaic modules enhanced in broadband range, which can improve the utilization efficiency of optical energy for the applications of sensing, imaging, optical communication, and energy harvesting.

Globally, rotavirus group A (RVA) remains a major cause of severe childhood diarrhea, despite the use of vaccines in &gt; 100 countries. RVA sequencing for local outbreaks facilitates investigation into strain composition, origins, spread, and vaccine failure. In 2018, we collected 248 stool samples from children aged &lt;13 years admitted with diarrheal illness to Kilifi County Hospital, coastal Kenya. Antigen screening detected RVA in 55 samples (22.2%). Of these, VP7 (G) and VP4 (P) segments were successfully sequenced in 48 (87.3%) and phylogenetic analysis based on the VP7 sequences identified seven genetic clusters with six different GP combinations; G3P[8], G1P[8], G2P[4], G2P[8], G9P[8] and G12P[8]. The G3P[8] strains predominated the season (n=37, 67.2%) and comprised three G3 genetic clusters that fell within Lineage I and IX (the latter also known as equine-like G3 lineage). Both two G3 lineages have been recently detected in several countries. Our study is the first to document African children infection with G3 lineage IX. These data highlight the global nature of RVA transmission and the importance of increasing global rotavirus vaccine coverage.

Globin-like superfamily constitutes a superfamily of both extracellular and intracellular proteins that are found in 3 kingdoms of life. Globins are respiratory proteins that usually bind an oxygen molecule .Earlier, phylogenetic study of globin like superfamily was based on morphological character, however, molecular basis of their functional diversity is not completely understood. The present study focuses on the phylogenetic analysis of globin at molecular level. Firstly, proteins of SCOP families of globin like superfamily were retrieved from NCBI and then similar proteins are retrieved from PSI BLAST results and then pfam was used to predict the domains and two domains: Globin and Phycobilisome were analysed. Other analysis predicted the localization in cytoplasm of most of the proteins. The nucleotide sequences of same species for protein analysis were retrieved from NCBI, and phylogenetic analysis of aligned fasta files of proteins and nucleotides by using MEGA at molecular level was performed and analysis shows the difference on taxonomic tree and phylogenetic tree.

Having garnered significant attention in the scientific community over the past decade, Wire Arc Directed Energy Deposition (arc-DED) technology is at the heart of this investigation into additive manufacturing parameters. Singularly focused on invar as the selected material, the primary objective revolves around devising an indirect cord height measurement approach. This innovative methodology involves the seamless integration of internal signals and sensors, enabling the derivation of crucial measurements sans the requirement for direct physical interaction or conventional measurement methodologies. Through the course of this research, meticulous alteration of deposition parameters is undertaken to thoroughly scrutinize their influence on the ultimate cord dimensions. The fusion of cutting-edge manufacturing techniques with advanced sensor technology constitutes the essence of this endeavor, offering substantial potential to augment precision and efficiency in additive manufacturing processes. Remarkably cost-effective, this solution circumvents the need for intricate measurements and significantly contributes to the proper layer-by-layer growth process.

The earth pressure acting on soilbag reinforced retaining structures subjected to surcharge loads under non-limited states, is crucial for designing these structures. In this study, the earth pressures are investigated through model tests of the soilbag reinforced retaining wall. Findings from these tests reveal a non-linear distribution of lateral earth pressure on the wall when subjected to surcharge loads in non-limited states, with an observed escalation in pressure corresponding to increased surcharge loads. Compression tests on soilbags were conducted to analyze their lateral stress-strain behavior. Insights from these tests facilitated the development of a predictive method for estimating lateral pressure on soilbag reinforced retaining walls under similar conditions. This method, rooted in the principle of force equilibrium in differential elements, has its accuracy and reliability substantiated by the alignment of its predictions with the model test outcomes.

Aluminum (Al) toxicity is the most common factor limiting the growth of alfalfa in acidic soil conditions. Melatonin (MT), a significant pleiotropic molecule present in both plants and animals, has shown promise in mitigating Al toxicity in various plant species. This study aims to elucidate the underlying mechanism by which melatonin alleviates Al toxicity in alfalfa through a combined physiological and transcriptomic analysis. The results reveal that 5 μM MT significantly alleviates Al-induced growth inhibition and preserves the morphology of root tip cells. Moreover, MT application reduces Al accumulation in alfalfa roots and shoots by 28.6% and 27.6%, respectively. Additionally, MT plays a crucial role in scavenging Al-induced excess H2O2 by enhancing the activities of superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), consequently reducing malondialdehyde (MDA) levels. The RNA-seq results reveal that MT application significantly upregulates the expression of xyloglucan endotransglucosylase/hydrolase (XTH) and carbon metabolism-related genes, including those involved in the glycolysis process, as well as sucrose and starch metabolism, suggesting that MT application may mitigate Al toxicity by facilitating the binding of Al to the cell walls, thereby reducing intracellular Al accumulation, and by improving respiration and the content of sucrose and trehalose. Taken together, our study demonstrates that MT alleviates Al toxicity in alfalfa by restoring redox homeostasis, enhancing Al binding to the cell wall, and modulating carbon metabolism. This research advances our understanding of the mechanisms underlying MT's effectiveness in mitigating Al toxicity, offering potential strategies for reducing Al accumulation in alfalfa.

There is a substantial lack of data relating to the hygrothermal traits of existing buildings and building materials. Moisture analysis in building envelopes is 1D (one-dimensional), and 2D and 3D effects and feedback can be neglected. Many European standards treat a moisture percentage in building envelopes as surface and interstitial moisture condensation, such as BS EN ISO 10211, BS EN ISO 13788, BS EN ISO 15148, and BS EN 15026. In this manuscript, there was a tendency to capture a relative quantity of superficial moisture, by metering spots on the inner and outer surface of wall lining systems with a moisture meter. The metering specimens were the buildings with different envelopes: a wooden hut-house, a masonry building and a building partially sheeted in stone. The referent heights on wall linings, for taking the moisture data were specified as 50 cm for a wooden and masonry building and 80 cm for a stone-sheeted building, from the ground. The obtained numeric results were palpable with no regard to the current state of the weather outside. The listed conclusions highlight the significance of a well-tailored building envelope, and its dependence on weather, junctions, gaskets, appropriate materials, etc.

Heart attacks and strokes are one of the leading causes of death in the world today, and heart attacks caused by clogged arteries that carry blood to the heart muscle are a significant part of these strokes. These are caused by the accumulation of fat particles in the walls of the arteries and the reduction of blood flow through it over a long process. The process of fat penetration in the underlying layers of the Artery wall has been the focus of many researchers, and various researches and Simulations have been done on it, in each of them, the effect of specific parameters has been considered. In the present study, the effect of blood flow rate on the flow pattern in a bifurcate artery with two ducts has been investigated using FLUENT software with Computation fluid dynamic Method. The effect of the angle between the two ducts of the Artery on the flow pattern has been investigated.

The hygrothermal transfer is very important for the design of a building envelope for thermal comfort and economic and energy analysis of the building envelope. The applications of various materials in building envelope have been studied extensively. The study presents several models for the hygrothermal transfer for various building walls. Several energy and mass conservation equations with different boundary conditions and input considerations were presented in this paper for concrete, bricks and wooden walls. The effect of hysteresis was ignored in developing most model equations, while few considered flow pattern of fluid through the wall surfaces. Due to the flexibility of Luikov models, it formed the basis for modelling the coupled heat and mass transfer for porous material independent of hygroscopic nature with different boundary conditions defined according to the geometry and orientations. The influence of type of wall, orientation, thickness, the density of the material and climatic variations on the temperature and moisture evolutions within the building materials was more pronounced. Literature, presenting imaging models using imagery software like COMSOL multi-physics, CFD etc. were scarce considering that microscopic imagery is now deployed to measure the heat and moisture evolution in materials. Future models should include shrinkage or expansion influence on the fibrous material like wood due to their behaviour under environmental condition.

In this paper, we present and analyze a compact inner-wall grating slot microring resonator (IG-SMRR) with the footprint of less than 13 μm × 13 μm on the SOI platform for label-free sensing, which comprises a slot microring resonator (SMRR) and inner-wall grating (IG). Its detection range is significantly enhanced without the limitation of the free spectral region (FSR) owing to the combination of SMRR and IG. Structural parameters of IG and SMRR are investigated and optimized for favorable transmission properties. The simulation results shows that the IG-SMRR has an ultra-large quasi-FSR of 84.6 nm, and the concentration sensitivities of sodium chloride solutions and D-glucose solutions are up to 960.61 pm/% and 933.06 pm/%, respectively. The investigation on the combination of SMRR and IG is a valuable exploration of label-free sensing application for ultra-large detection range and ultra-high sensitivity in future.

Filamentous fungi such as Aspergillus spp. are opportunistic pathogens, which cause highly invasive infections, especially in immunocompromised individuals. Control of such fungal pathogens is increasingly problematic due to the small number of effective drugs available for treatment. Moreover, the increased incidence of fungal resistance to antifungal agents makes this problem a global human health issue. The cell wall integrity system of fungi is the target of antimycotic drugs echinocandins, such as caspofungin (CAS). However, echinocandins cannot completely inhibit the growth of filamentous fungal pathogens, which results in survival/escape of fungi during treatment. Chemosensitization was developed as an alternative intervention strategy, where co-application of CAS with the intervention catalyst octyl gallate (OG; chemosensitizer) greatly enhanced CAS efficacy, thus achieved ≥ 99.9% elimination of filamentous fungi in vitro. Based on hypersensitive responses of Aspergillus antioxidant mutants to OG, it is hypothesized that, besides destabilizing cell wall integrity, the redox-active characteristic of OG may further debilitate fungal antioxidant system.

The use of mixed-state ionic beams in collision dynamics investigations is examined. Using high resolution Auger projectile spectroscopy involving He-like ($1s^2\thinspace^1\!S, 1s2s\thinspace^{3,1}\!S$) mixed-state beams, the spectrum contributions of the $1s2s\thinspace^3\!S$ metastable beam component is effectively separated and clearly identified. This is performed with a technique that exploits two independent spectrum measurements under the same collision conditions, but with ions having quite different metastable fractions, judiciously selected by varying the ion beam charge-stripping conditions. Details of the technique are presented together with characteristic examples. In collisions of 4 MeV B$^{3+}$ with H$_2$ targets, the Auger electron spectrum of the separated $1s2s\thinspace^{3}S$ boron beam component allows for a detailed analysis of the formation of the $1s2s(^3\!S)nl \thinspace^2\!L$ states by direct $nl$ transfer. In addition, the production of hollow $2s2p\thinspace^{1,3}\!P$ doubly- and $2s2p^2\thinspace^2\!D$ triply-excited states, by direct excitation and transfer-excitation processes, respectively, can also be independently studied. In similar mixed-state beam collisions of 15 MeV C$^{4+}$ with H$_2$, He, Ne and Ar targets, the contributions of the $1s^2$, $1s2s\thinspace^{3,1}S$ beam components to the formation of the $2s2p\thinspace^{3,1}\!P$ states by double-excitation, $1s\rightarrow2p$ excitation and transfer-loss processes can be clearly identified, facilitating comparisons with theoretical calculations.

Despite the recognized potential of nanoparticles, only a few formulations have progressed to clinical trials, and an even smaller number have been approved by the regulatory authorities and marketed. Virus-like particles (VLPs) have emerged as promising alternatives to most explored nanoparticles because of the absence of viral genetic material, their incapacity to replicate, mimicry of viral structure, and tropism conservation. Furthermore, VLPs can be surface functionalized with small molecules to improve circulation half-life and target specificity. Through the functionalization and coating of VLPs, it is possible to optimize the response properties to a given stimulus, such as heat, pH, an alternating magnetic field, or even enzymes. Surface functionalization can also modulate other properties, such as biocompatibility, stability, and specificity, deeming VLPs as potential vaccine candidates or delivery systems. In this review, we address the different types of functionalization of VLPs, their importance, and their consequent biomedical applications.

Glypicans are a family of heparan sulfate proteoglycans that are attached to the outer plasma membrane leaflet of the producing cell by a glycosylphosphatidylinositol anchor. Glypicans are involved in the regulation of many signalling pathways, including those that regulate the activities of Wnts, Hedgehog (Hh), Fibroblast Growth Factors (FGFs) and Bone Morphogenetic Proteins (BMPs), among others. In the Hh signalling pathway, glypicans have been shown to be essential for ligand transport and the formation of Hh gradients over long distances, for the maintenance of Hh levels in the extracellular matrix and for its unimpaired reception in distant recipient cells. Recently, two mechanistic models have been proposed to explain how Hh can form the signalling gradient and how glypicans may contribute to it. In this review, we describe the structure, biochemistry and metabolism of glypicans and their interactions with different components of the Hh signalling pathway that are important for the release, transport and reception of Hh.

Cardiac hypertrophy typically follows myocardial damage, a process known to involve members of the Krüppel-Like Factors (KLFs) which have pro-hypertrophic and anti-hypertrophic roles. Our study delved into the molecular mechanisms underlying KLFs-cardiac hypertrophy interplay post myocardial infraction. We induced myocardial dam-age in rats using isoproterenol. Total RNA was extracted from the left ventricle and Quantitative Real Time RT-PCR was conducted to assess the expression of KLFs, cardiac commitment genes, inflammatory markers, and certain conduction-related genes. We devel-oped a computational approach to construct a proteomic network centered on KLFs. Initial results revealed early expression (2-3 days post-induction) of KLF3, KLF4 and KLF6, followed by the subsequent expression of KLF11 and KLF15 (5-8 days after induction). In the maturation stage, KLF12 and KLF13 regulators were found upregulated. IL-6 was gradually found to be upregulated through. Interaction analysis revealed KLF3, KLF8 and KLF12 interacted with cardiac electrical functions. RT-PCR confirmed up-regulation in cardiac genes linked to electrical function and scar maturation. Our findings underscore the central role of KLFs during the modulation of the cardiac hypertrophic response. Dysregulation of KLF expression resulted in damaged myocardium, participating in the progression of abnormal hypertrophy, highlighting their potential as therapeutic targets for heart diseases.

Background: The number of people with type 2 diabetes is increasing daily, and therefore effective therapy is needed to successfully regulate glycemia and reduce the risk of associated complications. Recently, an oral formulation of the glucagon-like peptide-1 receptor agonist (GLP-1 RA) semaglutide has become available. Therefore, the aim of our study was to compare the effectiveness of the new oral formulation and the existing injectable formulation of semaglutide in terms of glycemic and body weight control in a real-world setting. Patients and methods: This was a single-center retrospective observational study conducted at the Rijeka Clinical Hospital Centre. A total of 106 patients with inadequately controlled type 2 diabetes (HbA1 ≥ 7%) on different oral or basal insulin supported oral therapy were recruited from the diabetes outpatient clinic, and data from electronic medical records were retrospectively collected and analyzed from May 2021 to November 2022. All subjects were GLP-1 RA naive and consequently prescribed 0.5 or 1.0 mg once weekly injectable semaglutide (IS) or 7 mg or 14 mg once daily oral semaglutide (OS) for at least 6 months. Glycated hemoglo-bin (HbA1c), body weight, and body mass index (BMI) were assessed prior to semaglutide administration and after a 6-month follow-up period. The primary endpoint was the change from baseline in HbA1c, and sec-ondary endpoints were the change in body weight and the proportion of participants with a reduction in body weight of ≥ 5% and ≥ 10%, respectively, 6 months after the initiation of semaglutide treatment. Results: At 6-month follow-up, no significant difference was observed between the two formulations in terms of HbA1c reduction (IS -1.1% vs OS -1.4%, p=0.126) and weight loss (IS -6.50 kg vs OS -5.90 kg, p=0.714). Exactly the same proportion of participants in both groups achieved a weight loss of ≥ 5% (56.7%, n=30). A weight loss ≥ 10% was observed in 20.7% (n=11) of participants administered IS and 15.1% (n=8) of participants adminis-tered OS, respectively (p=0.454). Conclusion: In a real-world setting, oral semaglutide as add-on therapy to ongoing antihyperglycemic treatment in patients with inadequately controlled type 2 diabetes who had not previously received GLP-1 RA demonstrated the same effectiveness as injectable semaglutide in terms of gly-cemic control and weight loss after 6 months of treatment.

Emerging evidence indicates that intracellular calcium (Ca2+) levels and their regulatory proteins play essential roles in normal stem cell proliferation and differentiation. Cancer stem-like cells (CSCs) are subpopulations of cancer cells that retain characteristics similar to stem cells and play an essential role in cancer progression. Recent studies have reported that the Orai3 calcium channel plays an oncogenic role in human cancer. However, its role in CSC remains underexplored. In this study, we explored the effects of Orai3 in the progression and stemness of oral/oropharyngeal squamous cell carcinoma (OSCC). Orai3 expression was increased in a stepwise manner during the progression of OSCC. In addition, Orai3 was highly enriched in CSC populations of OSCC. Ectopic Orai3 expression in non-tumorigenic immortalized oral epithelial cells increased intracellular Ca2+ levels, acquiring malignant growth and CSC properties. Conversely, silencing of endogenous Orai3 in OSCC cells suppressed CSC phenotype, indicating a pivotal role of Orai3 in CSC regulation. Moreover, Orai3 markedly increased the expression of inhibitor of DNA binding 1 (ID1), a stemness transcription factor. Orai3 and ID1 were highly expressed in CSCs compared to non-CSCs, implying the functional importance of the Orai3/ID1 axis in CSC regulation. Furthermore, suppression of ID1 abrogated CSC phenotype in the cell with ectopic Orai3 overexpression and OSCC. Our study reveals that Orai3 is a novel functional CSC regulator in OSCC and further suggests that Orai3 plays an oncogenic role in OSCC by promoting cancer stemness via ID1 upregulation.

Venoms are a rich source of bioactive compounds, and among them is leberagin-C (Leb-C), a disintegrin-like protein derived from the venom Macrovipera lebetina transmediterrannea snakes. Leb-C has shown promising inhibitory effects on platelet aggregation. Previous studies have demonstrated that this SECD protein specifically targets α5β1, αvβ3 and αvβ6 integrins through a mimic mechanism of RGD disintegrins. In our current study, we focused on exploring the potential effects of Leb-C on metastatic breast cancer. Our findings revealed that Leb-C disrupted the adhesion, migration, and invasion capabilities of MDA-MB-231 breast cancer cells and its highly metastatic D3H2LN sub-population. Additionally, we observed significant suppression of adhesion, migration, and invasion of Human Umbilical Vein Endothelial Cells (HUVECs). Furthermore, Leb-C demonstrated a strong inhibitory effect on fibroblast growth factor 2-induced proliferation of HUVEC. We conducted in vivo experiments using nude mice and found that treatment with 2 µM of Leb-C resulted in a remarkable 73% reduction in D3H2LN xenograft tumor size. Additionally, quantification of intratumor microvessels revealed a 50 % reduction in tumor angiogenesis in xenograft after 21 days of twice-weekly treatment with 2 µM of Leb-C. Collectively, these findings suggest the potential utility of this dinsintegrin-like protein for inhibiting aggressive and resistant metastatic breast cancer.

KLFs seem to associate with congenital heart disease-linked syndromes, malformations because of autosomal diseases, mutations that relate to protein instability, and/or loss functions such as atheroprotective activities. Ischemic damage also relates to KLF dysregulation because of differentiation of cardiac myofibroblasts or a modified fatty acid oxidation, related to the formation of a dilated cardiomyopathy; myocardial infarctions, left ventricular hypertrophy and diabetic cardiomyopathies. MicroRNA have been involved in certain regulatory loops of KLFs as they may function as critical modulators of vascular smooth muscle cells in atherosclerosis, in heart failure and as markers of endothelial damage in acute myocardial infarction.

Glioblastoma (GBM) still presents as one of the most aggressive tumors in the brain, which despite enormous research efforts remains incurable until today. As many theories evolve around the persistent recurrence of this malignancy the assumption of a small population of cells with a stem-like phenotype remains as a key driver of its infiltrative nature. In this article we research Chordin-like 1 (CHRDL1), a secreted protein, as a potential key regulator of the glioma stem-like cell (GSC) phenotype. It has been shown that CHRDL1 antagonizes the function of Bone Morphogenic Protein 4 (BMP4), which induces GSC differentiation and hence reduces tumorigenicity. We therefore employed two previously described GSCs spheroid cultures and depleted them of CHRDL1 using stable transduction of a CHRDL1-targeting shRNA. We show with in vitro cell based assays (MTT, limiting dilution and sphere formation assays), western blots, irradiation procedures and quantitative real-time PCR that depletion of the secreted BMP4 antagonist CHRDL1 prominently decreases functional and molecular stemness traits resulting in enhanced radiation sensitivity. As a result, we postulate CHRDL1 as an enforcer of stemness in GSCs and find additional evidence that high CHRDL1-expression might also serve as a marker protein to determine BMP4-susceptibility.

Purpose: The study aimed to investigate if there were any links between liver function biomarkers and immunoglobulins levels in serum, and Toll-like receptors (TLRs) and neuropilin-1 (NRP1) in COVID-19 patients. The study also aimed to assess the accuracy—sensitivity, specificity, and area under the curve (AUC) by the receiver operator curve (ROC) analysis for immunoglobulins levels and TLRs expressions. Patients and Methods: This study included 150 patients (100 patients with confirmed COVID-19 and 50 healthy volunteers as a control group). Patients with COVID-19 were subdivided into two groups according to the severity of symptoms (moderate and severe, with 50 patients each). Serum C-reactive protein (CRP), alanine aminotransaminase (ALT), aspartate aminotransaminase (AST), albumin, lactate dehydrogenase (LDH), immunoglobulin (Ig) G, and IgM levels were estimated. TLRs (TLR2 and TLR4) and NRP1 gene expression in blood samples were investigated using quantitative real-time polymerase chain reaction (qRT-PCR). ROC analysis was also applied to determine the accuracy of various detected parameters in predicting the possibility of COVID-19 infection. Results: In COVID-19 patients, serum parameters related to liver function, except serum albumin, CRP, IgG, IgM, and TLR2, TLR4, and NRP1 mRNA expression levels, significantly elevated compared to controls. Severe COVID-19 patients exhibited significantly higher liver enzymes (ALT, AST and LDH), CRP, and TLR2 mRNA expression levels and lower albumin levels than the moderate group. In the moderate and severe groups, ALT, CRP, TLR2, and TLR4 had a significant positive correlation with IgM levels. ALT, AST, LDH, CRP, TLR2, and TLR4 showed a significant positive correlation with IgG levels in both groups. In both the moderate and severe groups, NRP1 expression was found to be significantly correlated with CRP, IgG, IgM, TLR2, and TLR4. In contrast, serum albumin levels exhibited a significant negative correlation with IgG and IgM levels only in the severe group, but they showed a significant negative correlation with TLR2, TLR4, and NRP1 expression in both moderate and severe groups. Serum ALT and AST activities were positively correlated with NRP1 expression in the moderate group but not in the severe group and as well as TLR2 and TLR4 expression in both the moderate and severe groups. ROC analysis indicated that AUC was higher than 0.800 for serum IgM level and TLR4 gene expression in moderate COVID-19 group. Conclusions: The increased liver function biomarkers in serum and NRP1 expression are closely correlated with sustained activations in humoral and innate immune responses during COVID-19 infection. As a result, TLR2, TLR4, and NRP1 could be targets for limiting COVID-19 infection and impairment effects on liver function. Moreover, detection of IgM level in serum and TLR4 expression in blood have a good accuracy in predicting the possibility of infection with COVID-19 in moderate cases.

Background/Aim: Uterine leiomyoma, also known as fibroids, is the most common benign neoplasm of the female genital tract. Leiomyoma, including its subtypes, is the most common uterine tumor. The subtypes account for approximately 10% of leiomyomas. Intravenous leiomyomatosis, a uterine leiomyoma subtype, is an intravascular growth of benign smooth muscle cells, occasionally with pelvic or extrapelvic extension. Uterine leiomyosarcoma, a malignant tumor, tends to metastasize hematogenously, and distant metastasis to the lungs and liver is common. Therefore, this intravenous leiomyomatosis’ oncological features resemble those of the malignant tumor uterine leiomyosarcoma. Cancer stem cells migrate to distant organs via intravascular infiltration, leading to micrometastases. Materials and Methods: We examined the oncological properties of intravenous leiomyomatosis using molecular pathological techniques on tissue excised from patients with uterine leiomyoma. Result: CD44-positive mesenchymal tumor stem-like cells were detected in both intravenous leiomyomatosis and uterine leiomyosarcoma. The oncological nature of intravenous leiomyomatosis was found to be similar to the oncological properties of uterine leiomyosarcoma. However, in intravenous leiomyomatosis, Cyclin E and Ki-67-positive cells were rare, and no pathological findings suspected to be malignant were observed. Conclusion: It is expected that establishing a treatment method targeting cancer stem cells will lead to the treatment of malignant tumors with a low risk of recurrence and metastasis.

: Glioblastoma (GBM) is the most common and most aggressive primary brain tumor with a very high rate of recurrence and a median survival of 15 months after diagnosis. Abundant evi-dence suggests that a certain sub-population of cancer cells harbors a stem-like phenotype and is likely responsible for disease recurrence, treatment resistance and potentially even for the infil-trative growth of GBM. GBM incidence has been negatively correlated with the serum levels of 25-hydroxy-vitamin D3, while the low pH within tumors has been shown to promote the ex-pression of the vitamin D3-degrading enzyme 24-hydroxylase, encoded by the CYP24A1 gene. Therefore, we hypothesized that calcitriol can specifically target stem-like glioblastoma cells and induce their differentiation. Here, we show using in vitro limiting dilution assays, quantita-tive real-time PCR and ex vivo adult organotypic brain slice transplantation cultures that thera-peutic doses of calcitriol, the hormonally active form of vitamin D3, reduces stemness to varying extent in a panel of investigated GSC lines and effectively hinders tumor growth of responding GSCs ex vivo. We further show that calcitriol synergizes with Temozolomide ex vivo to com-pletely eliminate some GSC tumors. These findings indicate that calcitriol carries potential as an adjuvant therapy for a subgroup of GBM patients and should be analyzed in more detail in fol-low-up studies.

Toll-like receptors (TLRs) are a class of pattern recognition receptors (PRRs) family that identify pathogen-associated molecular patterns derived from microbes and activate immune cell response. Following TLRs ligation, different adaptor and transcription molecules such as myeloid differentiation primary response gene 88 (MyD88) and nuclear factor kappa B (NF-kB) are recruited that initiate inflammatory signaling pathways. The human Toll-like receptor 10 (hTLR10) is a novel member of the PRRs family with a regulatory function of immune responses because of unique cytoplasmic domains which lead to induction of both inflammatory and anti-inflammatory properties. Recent studies have reported the association of TLR10 polymorphisms with many inflammatory diseases and human cancer. Engagement of TLR10 on the surface of the epithelium and macrophages leads to the production of proinflammatory cytokines and chemokines, while other studies have proven an anti-inflammatory role of TLR10. Accordingly, TLR10 suppresses proinflammatory cytokine production via negative regulation of MyD88 and the Akt (protein kinase B) and MAPK (mitogen-activated protein kinase) signaling pathways. This review aimed to provide answers for these conflicting findings (Inflammatory and anti-inflammatory properties of TLR10) to further identify distinct biological functions of TLR10.

Bufadienolides-like chemicals, which mostly composed the active ingredient of Chansu, had been widely discovered to possess anti-inflammatory, tumor-suppressing and antipain activity, but the mechanisms of action were not clearly illuminated. In this research, in order to explore the potential mechanism of bufadienolides-like chemicals on breast cancer, a serious of bioinformatics analysis, included (1) differentially expressed genes identification combined with gene set variation analysis, (2) tissue specific co-expression network construction, (3) differentially regulated sub-networks detection with disease phenome, (4) hub gene selection and it’s relation to survival probability, and (5) similar small molecule detection were performed with gene expression profiles of bufadienolides-like chemicals. Results indicated bufadienolides-like chemicals had the most same target with valproic, estradiol and etc, could disturbed the pathways in RNA splicing, apoptotic process, cell migration, extracellular matrix organization, adherens junction organization, synaptic transmission, Wnt signaling, AK-STAT signaling, BMP signaling pathway and unfolded protein response, and had the potential ability to be used as anticancer, hormones and vasoprotectives agents.

Toll-like receptor 4 (TLR4) is a member of the TLR family. Members of the TLR family play an important role in innate immune responses and are induced by recognition of pathogen-associated molecular patterns. They are also involved in cell proliferation and apoptosis in cancer. We investigated the role of TLR4 in apoptotic cell death in gynecological cancer cells; gynecological cancer is associated with infertility and spontaneous abortion. To examine the effect of TLR4 activation on apoptotic signaling in cancer cells, cultured primary cancer cells were treated with the TLR4 agonist lipopolysaccharide (LPS). The morphology of cancer cells was compared with normal myometrial cells. Enhanced growth rate and loss of contact inhibition with cellular overlap was observed in the cancer cells. The molecular mechanism analysis revealed differential expression of tumor suppressor genes in LPS-treated cancer cells. The expression of apoptosis-related caspase-3 was increased significantly in cancer cells with TLR4 activation after exposure to LPS. Taken together, these results suggest the pro-apoptotic activity of TLR4 as a potential therapeutic target for the treatment of gynecological cancers.

Astronauts at are risk of losing 1.0 – 1.5% of their bone mass for every month they spend in space despite their adherence to high impact exercise training programs designed to preserve the musculoskeletal system. This article reviews the basics of bone formation and resorption and details how exposure to microgravity or simulated microgravity affects the structure and function of osteoblasts, osteocytes, osteoclasts, and their mesenchymal and hematologic stem cell precursors. It details the critical roles that insulin-like growth facor-1 and its receptor IGFR1 play in maintaining bone homeostasis and how exposure of bone cells to microgravity affects the function of these growth factors. Lastly, it discusses the potential of tumor necrosis factor-related apoptosis-inducing ligand, syncytin-A, and sclerostin inhibitors and recombinant IGF-1 as a bone-saving treatment for astronauts in space and during their colonization of the Moon.

Jingmen viruses are newly described segmented flavi-like viruses that have a worldwide distribution in ticks and have been associated with febrile illnesses in humans. Computational analyses were used to predict that Jingmen flavi-like virus glycoproteins have structural features of class II viral fusion proteins, including an ectodomain consisting of beta-sheets and short alpha-helices, a fusion peptide with interfacial hydrophobicity and a three domain architecture. Jingmen flavi-like virus glycoproteins have a sequence enriched in serine, threonine and proline at the amino terminus, which is a feature of mucin-like domains. Several of the serines and threonines are predicted be modified by the addition of O-linked glycans. Some of the glycoproteins are predicted to have an additional mucin-like domain located prior to the transmembrane anchor, whereas others are predicted to have a stem consisting of two alpha-helices. The flavivirus envelope protein and Jingmen flavi-virus glycoproteins may have diverged from a common class II precursor glycoprotein with a mucin-like domain or domains acquired after divergence.

When the epipelic algae group growing on the concrete inclined side wall, which is typical of urban rivers and open diversion channels, enters the water flow, it will seriously affect the func-tion of the rivers or the channels. It is urgent to predict the transport capacity of epipelic algae group with water flow. However, the current research on the transport of pollutants is mostly based on mathematical models, and the study of the transport of flake epipelic algae group is extremely rare. A generalized hydrodynamic experimental model of a flume with sidewall epi-pelic algae group was established. Through a series of hydraulic experiments, the physical movement form and transport capacity of the suspended epipelic algae group on the side wall of the channel were studied qualitatively and quantitatively by taking the thickness, sheet size and flow rate of the epipelic algae group as the influencing factors. The key influencing factors of the suspension of epipelic algae are clarified, so as to quantitatively analyze the critical conditions of its suspension. Through flow scheduling, the probability of epipelic algae gathering some-where is increased. It provides a theoretical basis for realizing the long-distance migration of epipelic algae and optimizing the mathematical model.

We presented unusual case of double left ventricular false aneurysm complicating late presentation AMI successfully treated with the combination of urgent surgical drainage of tamponade, staged PCI of non-culprit lesion, preventive implantation of ICD-DR, guideline directed heart failure medical therapy and delayed but effective reconstructive operation.

Aluminum (Al) and manganese (Mn) toxicity are the top two constraints to crop production in acid soil. Crops have evolved common and specific mechanisms to tolerate the two stresses. In the present study, the responses (toxicity and tolerance) of wheat near-isogenic lines (ET8 and ES8) and their parents (Carazinho and Egret) to Al and Mn were compared by determining physiolog-ical parameters and transcriptome profiling of roots. The results showed that: (1) Carazinho and ET8 exhibited dual tolerance to Al and Mn as compared with Egret and ES8, indicated by higher relative root elongation and SPAD; (2) After entering into roots, Al was mainly distributed in the root and fixed in the cell wall, while Mn was mainly distributed in the cell sap and then trans-ported to leaves. Both Al and Mn stresses decreased the contents of Ca, Mg, and Zn; Mn stress al-so inhibited the accumulation of Fe, while Al showed an opposite effect; (3) Transcriptomic analy-sis identified 5581 differentially expressed genes (DEGs) under Al stress and 4165 DEGs under Mn stress. Among these, 2774 DEGs were regulated by both Al and Mn stresses, while 2280 and 1957 DEGs were exclusively regulated by Al and Mn stress, respectively. GO and KEGG analyses indi-cated that cell wall metabolism responds exclusively to Al, while nicotianamine synthesis exclu-sively responds to Mn. Pathways such as signaling, phenylpropanoid metabolism, and metal ion transport showed commonality and specificity to Al and Mn. TFs, such as MYB, WRKY, and AP2 families, were also regulated by Al and Mn, and WGCNA identified PODP7, VATB2, and ABCC3 as the hub genes for Al tolerance and NAS for Mn tolerance. The identified genes and pathways can be used as targets for pyramiding genes and breeding multi-tolerant varieties.

Haemodynamic simulations are increasingly used to study vascular diseases like Intracranial Aneurysms (IA) and to further develope treatment options. However, due to limited data, some aspects must rely on heuristics, especially at the simulation’s distal ends. In literature, Murray’s Law is often used to model the outflow split based on vessel cross-section area, but this poses challenges for the communicating arteries in the Circle of Willis (CoW). In this study, we contribute by assessing the impact of Murray’s Law in patient-specific geometries featuring IA at the posterior communication. We simulate different domain extensions, representing common modelling choices. We establish Full CoW simulations as a baseline to evaluate the effect of these modelling assumptions on haemodynamic indicators, focusing on IA growth and rupture-related factors like Wall Shear Stress (WSS) and Oscillatory Shear Index (OSI). Our findings reveal qualitative alterations in haemodynamics when not modeling posterior communication. Comparisons between computing the anterior circulation and computing the whole Circle of Willis reveal quantitative changes in WSS may reach up to 80%, highlighting the significance of modelling choices in assessing IA risks and treatment strategies.

Abdominal entry is the critical initial step of laparoscopic surgery as it is associated with unexpected complications. Acceptable working space is a prerequisite for safe minimal access surgery. Direct trocar insertion (DTI) technique has been often reported to be time-consuming and capable of causing injuries. We aim to facilitate conventional DTI employing an easy-to-use self-designed abdominal wall-lifting device, OneShot-M. We tested its safety in a porcine model. 18 pigs were randomized into three groups (n=6): open laparoscopy (Group A), DTI (Group B), DTI using OneShot-M (Group C), suitable for a 5-mm trocar. Outcomes were access time, entry-related minor and major complications. Median access time was shorter in C (43 seconds; range: 35-49 seconds), followed by B (82.5; 72-90) and A (190.5; 182-240). Statistically significant differences in procedural time between techniques were detected (p-value = 0.0005). Pairwise comparisons exhibited a statistically significant difference between A and C in terms of access time. Only one difficulty in entry was seen in C; pigs experienced several occurrences in A and B. This pilot study suggests that OneShot-M appears to be a technically feasible, fast and safe method for pneumoperitoneum induction in a porcine model, as it provides sufficient exposure of the operative field without access-related complications. Further clinical studies are needed.

The construction of large-scale water diversion projects alleviated effectively the current situa-tion of uneven distribution of water resources in China. However, due to the siltation of very fine sediment and organic matter on the side wall of the open channel, and the slow velocity of the side wall flow field, it is easy to produce epipelic algae, which affects water quality. For the prototype observation cannot be used to predict the series of flow in real time, and the mathe-matical model calculation is affected by parameter limitations, these two methods often cannot truly reflect the hydrodynamic characteristics of open channel with epipelic algae. Therefore, by referring to the design parameters of the water diversion project channel, this paper takes the epipelic algae growing on the side wall of the open channel as the research object, and uses the scale of 1:30 to carry out the generalized flume experiment. Through the analysis of the physical characteristics of the prototype sample, and the simulation of the cohesive force between the oblique side wall and the epipelic algae, the multi-group and multi-series hydrodynamic tests are carried out. The flow velocity distribution law and the development and change of the tur-bulent vortex on the side wall are analyzed. It has important scientific guiding significance and practical value for water quantity regulation water regulation and water quality safety protec-tion of long-distance projects.

Some biologically active compounds isolated from sea cucumbers stimulate the body’s immune response through activating immune cells. Immune function is closed related to the integrity intestinal barrier and balanced gut microbiota. However, it is unknown whether daily administration of holothurian wall hydrolysates (HWH) ameliorated intestinal dysbiosis and barrier injury induced by immunodeficiency. This study aimed to investigate the immunomodulatory effect and the underlying mechanism of HWH in cyclophosphamide (CTX)-induced immunocompromised mice. BALB/c mice received CTX (80 mg/kg, intraperitoneally) once a day for 3 days to induce immunodeficiency, and then oral administration of HWH (80 or 240 mg/kg), levamisole hydrochloride (LH, 40 mg/kg, positive control) respectively once a day for 7 days. We utilized 16S rRNA sequencing for microbial composition alterations, histopathological analysis for splenic and colonic morphology, Western blotting for expressions of tight junction proteins (TJs), and quantitative real-time (qRT-PCR) for measurements of pro-inflammatory cytokines. HWH attenuated the immune organ damage induced by CTX, increased the secretions of interleukin (IL)-6, IL-1β and tumor necrosis factor (TNF)-α, and promoted the recovery of goblet cells and the productions of TJs (claudin-1, occludin, and ZO-1) in the colon of the immunocompromised mice. Moreover, HWH promoted the growth of beneficial microorganisms such as Lactobacillus, Lachnospiraceae, Christensenellaceae, and Bifidobacterium, while suppressed the populations of Ruminococcus, Staphylococcus, and Streptococcus. These results demonstrate that HWH elicits intestinal mucosal immunity, repairs the damage to intestinal mucosal integrity, and normalizes the imbalanced intestinal microbial profiles in immunocompromised mice. It may be helpful to identify the biological activities of HWH, and supports the potential as new prebiotics, immunomodulatory agents, and medical additive for intestinal repair.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

To live in the information society means to be surrounded by billions of electronic devices full of sensors that constantly acquire data. This enormous amount of data must be processed and classified. A solution commonly adopted is to send these data to server farms to be remotely elaborated. The drawback is a huge battery drain due to high amount of information that must be exchanged. To compensate this problem data must be processed locally, near the sensor itself. But this solution requires huge computational capabilities. While microprocessors, even mobile ones, nowadays have enough computational power, their performance are severely limited by the Memory Wall problem. Memories are too slow, so microprocessors cannot fetch enough data from them, greatly limiting their performance. A solution is the Processing-In-Memory (PIM) approach. New memories are designed that are able to elaborate data inside them eliminating the Memory Wall problem. In this work we present an example of such system, using as a case of study the Bitmap Indexing algorithm. Such algorithm is used to classify data coming from many sources in parallel. We propose an hardware accelerator designed around the Processing-In-Memory approach, that is capable of implementing this algorithm and that can also be reconfigured to do other tasks or to work as standard memory. The architecture has been synthesized using CMOS technology. The results that we have obtained highlights that, not only it is possible to process and classify huge amount of data locally, but also that it is possible to obtain this result with a very low power consumption.

Inertial focusing conditions of fluorescent polystyrene spherical particles are studied at the pointwise level along their pathlines. This is accomplished by an algorithm that calculates a de-gree of spreading function of the particles' trajectories taking streaklines images as raw data. Different confinement ratios of the particles and flow rates are studied and the results are pre-sented in state diagrams showing the focusing degree of the particles in terms of their position within a curve of an asymmetric serpentine and the applied flow rate. In addition, together with numerical simulation results, we present empirical evidence that the preferred trajectories of inertially focused spheres are contained within Dean vortices' centerlines. We speculate about the existence of a new force, never postulated before, to explain this fact.

Glucagon-like peptide-1 (GLP-1) is an incretin hormone that acts on the pancreas to increase insulin and decrease glucagon secretion. Albuminuria is the pivotal marker for diabetic nephropathy, which is the leading microvascular complication of diabetes mellitus. Most of the previous studies mainly focused on the clinical trials of the therapeutic renal protective effect after administration of GLP-1 receptor agonists (GLP-1 RAs), not prior to administration. Therefore, this study aimed to investigate the association between fasting plasma GLP-1 levels and albuminuria before GLP-1 RA administration. A cross-sectional study was designed to evaluate the association between fasting plasma GLP-1 levels and albuminuria in patients with type 2 diabetes mellitus (T2DM). A total of 68 T2DM participants were analyzed from the data at Wonkwang University Hospital in Iksan, Korea. Logistic regression analysis was performed to evaluate the odds ratio (OR) and 95% confidence interval (CI) of the incidence of albuminuria between the GLP-1 low group (Group L) and the high group (Group H). The OR (95% CI) for the incidence of albuminuria comparing the Group L with the Group H of fasting plasma GLP-1 levels was 3.410 (1.160-10.023), p = 0.026 after adjustment for age, gender, fasting plasma glucose, HbA1c, C-peptide, the use of ACE inhibitors or ARBs, SGLT-2 inhibitors, and DPP-4 inhibitors. As a continuous variable, the OR (95% CI) for the incidence of albuminuria associated with the reduction of each 1 pmol/L in fasting plasma GLP-1 levels was 1.673 (1.173-1.870), p = 0.018, after full adjustment. This study showed the negative association between fasting plasma GLP-1 levels and the incidence of albuminuria in Korean patients with T2DM, before GLP-1 RA administration. This result suggests that endogenous GLP-1 may play a role in attenuating albuminuria.

The red fox, found on all continents except Antarctica, occupies diverse habitats. In Croatia it is an indigenous wild species with a population density of 0.7 animals per square kilometer. While tumors in wild animals from the Canidae family are scarce, the true prevalence and diversity of tumors are likely underestimated due to limited research. So far, a limited number of tumors were observed among the red fox population, either in their natural habitat or in captivity. As part of the National rabies control program, we examined 1,890 red fox carcasses over a four-year period. Our focus was on identifying abnormalities on the skin and internal organs that suggest potential neoplastic proliferation. Five red foxes, three males and two females, were found to have growths resembling potential tumors. Their age distribution spanned from 2 to 7 years. Microscopic investigation revealed two collagenous hamartomas, two Meibomian gland adenomas and one intra-abdominal teratoma within a cryptorchid testis. This retrospective study aims to provide a comprehensive description of tumor and tumor-like lesions observed in free-range red foxes from Croatia, marking the first research of its kind in Croatia.

The effect of ferromagnetic CaMnO3 (CMO) addition on structural, magnetic, dielectric, and ferroelec-tric properties of BiFeO3 are presented. X ray diffraction and Raman investigation allowed the identifi-cation of single pseudo cubic perovskite structure. The magnetic measurement showed that the pre-pared films exhibit a ferromagnetic behavior at low temperature with both coercive field and remnant magnetization increased with increasing CMO content. However, a deterioration of magnetization was observed at room temperature. Ferroelectric study revealed an antiferroelectric like behavior with a pinched P-E hysteresis loop for 5%CMO doping BFO resulting in low remnant polarization and double hysteresis loops. Whereas, high remnant polarization and coercive field with a likely square hysteresis loop are obtained for 10 % CMO addition. Furthermore, a bipolar resistive switching behavior with a threshold voltage of about 1.8V is observed for high doped film that can be linked to the ferroelectric polarization switching.

The Burkholderia cepacia complex (Bcc) are a group of increasingly multi-drug resistant opportunistic bacteria that can cause severe pulmonary infections. This resistance is driven through a combination of intrinsic factors and the carriage of a broad range of conjugative plasmids harbouring virulence determinants. Therefore, novel treatments are required to not only treat Bcc infection but also to prevent further spread of these virulence determinants. In the search for phages infective for two clinical Bcc isolates, CSP1 phage, a PRD1-like phage was isolated. CSP1 phage was found to require pilus machinery commonly encoded on conjugative plasmids to facilitate infection of multiple Gram-negative bacteria genera including Escherichia and Pseudomonas. Whole genome sequencing and characterisation of one of the clinical Burkholderia isolates revealed it to be Burkholderia contaminans. B. contaminans 5080 was found to contain a genome of over 8 Mbp encoding multiple intrinsic resistance factors, such as efflux pump systems, but more interestingly, carried three novel plasmids encoding multiple putative virulence factors for increased host fitness, including antimicrobial resistance. Even though PRD1-like phages are broad host range, their use in novel antimicrobial treatments shouldn’t be dismissed, as the dissemination potential of conjugative plasmids is extensive. Continued survey of clinical bacterial strains is

In the chronic phase of chikungunya virus (CHIKV) infection, excessive inflammation manifests as incapacitating joint pain and prolonged arthritis. Arthritis resulted from a large influx of infiltrating immune cells driven by pro-inflammatory cytokines and chemokines originating from the toll-like receptor (TLR)-mediated innate antiviral response. This study investigated fisetin's ability to modulate TLR-mediated antiviral responses against CHIKV in Huh7 cells. The CHIKV inhibitory potential of fisetin was assessed by plaque-forming unit assay, virus yield reduction assay, and bright-field microscopy (cytopathic effect, immunofluorescence). Fisetin’s modulatory potential on TLR-mediated antiviral response was evaluated by immunofluorescence assay (expression of TLR proteins), qRT-PCR (mRNA level of antiviral genes), human cytokine array, and immunoblotting of key transcription factors. The present study showed fisetin induced the expression of the antiviral genes at an early time-point by promoting the phosphorylation of IRF3 and IRF7. Fisetin reduced excessive inflammatory cytokine responses in CHIKV-infected Huh7 cells by impeding the over-phosphorylation of NF-κB. Fisetin also reduced CHIKV-induced cytopathic effects in CHIKV-infected Huh7 cells. Altogether, our study suggests that fisetin modulates TLR-mediated antiviral responses by affecting the CHIKV-induced inflammatory responses.

A half-harmonic oscillator, which gets its name because the coordinate is strictly positive, has been quantized and determined that it was a physically correct quantization. This positive result was found using affine quantization (AQ). The main purpose of this paper is to compare results of this new quantization procedure with those of canonical quantization (CQ). Using Ashtekar-like classical variables and CQ, we quantize the same toy model. While these two quantizations lead to different results, they both would reduce to the same classical Hamiltonian if $\hbar\rightarrow0$. Since these two quantizations have differing results, only one of the quantizations can be physically correct. Two brief sections illustrate how AQ can correctly help quantum gravity and the quantization of most field theory problems.

The measurements of the proton electromagnetic form factors in the time-like region using the initial state radiation technique are reviewed. Recent experimental studies have shown that initial state radiation processes at high luminosity electron-positron colliders can be effectively used to probe the electromagnetic structure of hadrons. The BABAR experiment at the B-factory PEP-II in Stanford and the BESIII experiment at the $\tau$-charm factory BEPC-II in Beijing have measured the time-like form factors of the proton using the initial state radiation process $e^{+}e^{-}\to pbar{p}\gamma$. The two kinematical regions where the photon is emitted from the initial state at small and large polar angles have been investigated. In the first case the photon is in the region not covered by the detector acceptance and is not detected. The Born cross section and the proton effective form factor have been measured over a wide and continuous range of the the momentum transfer squared $q^2$ from threshold up to ~42 (GeV/c)$^2$. The ratio of electric and magnetic form factors of the proton has been also determined. In this report, the theoretical aspect and the experimental studies of the initial state radiation process $e^{+}e^{-}\to p\bar{p}\gamma$ are described. The measurements of the Born cross section and the proton form factors obtained in these analyses near the threshold region and in the relatively large $q^2$ region are examined. The experimental results are compared to the predictions from theory and models. Their impact on our understanding of the nucleon structure is discussed.

There is a relationship between systemic sarcoidosis (SS) and malignancy. Sarcoidosis results from an exaggerated immune response in genetically susceptible individuals. In oncologic pa-tients with sarcoidosis, tumoral antigens and antineoplastic treatment are considered potential triggering factors. The observation of a patient with granulomas in a parotid carcinoma that later developed SS led us to review previous tumors of patients with SS. The aim of the study is to see if granulomas were already present in the tumors that preceded sarcoidosis. We identified 196 sarcoidosis patients, 47 of which had a previous tumor. We were able to review 29 cases 12 of which showed tumor associated granulomas (TAGs)(41.4%). This ratio is much higher than that of the normal population. We analyzed five control patients without sarcoidosis for each tumor. In conclusion, we have observed TAGs in patients who later develop SS. In our series, the ratio of TAGs in patients with SS was significantly greater than in the normal population. To prove our findings, we suggest reviewing the history of patients with SS in search of previous tumors. The histology of such tumors should be reviewed in an attempt to identify granulomas.

Currently, the world is struggling with the coronavirus disease 2019 (COVID-19) pandemic, caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Prion-like domains are critical for virulence and the development of therapeutic targets; however, the prion-like domains in the SARS-CoV-2 proteome have not been analyzed. In this in silico study, using the PLAAC algorithm, we identified the presence of prion-like domains in the SARS-CoV-2 spike protein. Compared with other viruses, a striking difference was observed in the distribution of prion-like domains in the spike protein, since SARS-CoV-2 was the only coronavirus with a prion-like domain found in the receptor-binding domain of the S1 region of the spike protein. The presence and unique distribution of prion-like domains in the SARS-CoV-2 receptor-binding domains of the spike protein is particularly interesting, since although the SARS-CoV-2 and SARS-CoV S proteins share the same host cell receptor, angiotensin-converting enzyme 2 (ACE2), SARS-CoV-2 demonstrates a 10- to 20-fold higher affinity for ACE2. Finally, we identified prion-like domains in the α1 helix of the ACE2 receptor that interact with the viral receptor-binding domain of SARS-CoV-2. Taken together, the present findings indicate that the identified PrDs in the SARS-CoV-2 receptor-binding domain (RBD) and ACE2 region that interact with RBD have important functional roles in viral adhesion and entry.

The ongoing pandemic of the 2019 novel coronavirus disease (COVID-19) raises a global health crisis, which has resulted in 75,778 confirmed cases with 2130 deaths in China and beyond. Atypical symptom renders it challenging to earlier recognize the 2019-nCoV carrier with the potential ability of equivalent transmission. Therefore, it is needed to gain full spectrum of COVID-19. Here we report clustered COVID-19 cases of person-to-person transmission. The symptoms of typical pneumonia are shared by the two familial members, namely son (Patient 1) and father (Patient 2). Unexpectedly, an influenza-like illness (ILI) is also caused in Patient 3 having close contact with Patient 1 at personal dinner party. Combined with clinical and epidemiological study, chest computed tomography (CT) and molecular diagnosis demonstrate that all the three cases tested positive for COVID-19 with distinct symptoms by human-to-human transmission. To the best of knowledge, it closes in part (if not all), a missing gap of clinical repertoires of COVID-19 outbreaks and underlines the possibility that neglection of cryptic/asymptomatic/mild cold-like syndromes gives biased screen in the earlier stage of COVID-19 cases.