This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

The impact of nutrients on the environment, particularly on water bodies, has led to extensive studies for nutrient control. Within this context, studies have been focused on source separation of human urine from domestic wastewater to recover nutrients. Potassium is one of the most important components of human urine. However, data on potassium removal or recovery are quite limited except for some indirect information through use of zeolites for mostly ammonia removal. Potassium struvite or K-struvite (MgKPO₄·6H₂O) is a sparingly soluble salt belonging to struvite and has the potential of being used as a means of potassium and phosphate recovery from segregated human urine. This study aimed to assess the potential of K-struvite precipitation for control and recovery of nutrients. Within this context, K-struvite precipitation experiments were performed on both synthetically prepared samples and synthetic human urine solution to determine effect of operation parameters i.e. pH, stoichiometry, and temperature on potassium recovery performance. Results indicated that process performance as well as type of solid phases co-precipitated with K-struvite were closely related to initial potassium concentration, pH and reaction stoichiometry. At pH 10, the potassium recovery efficiency was maximized up to 87% by application of 100% excess dose of Mg and P for both synthetic samples and synthetic human urine solution. On the other hand, application of excess dose of K did not provide any improvement in K recovery efficiency. The effect of temperature on solubility of K-struvite was insignificant at the temperature of 24-90°C. Solid phase analyses confirmed that K-struvite was co-precipitated with either Mg₃(PO₄)₂, MgNaPO₄·7H₂O, or MgHPO₄·7H₂O depending on pH and stoichiometry instead of a pure compound.

To date, zinc ion batteries (ZIBs) have been attracting extensive attention due to their outstanding properties and the potential to be the solution for next-generation energy storage systems. However, the uncontrollable growth of zinc dendrites and water-splitting issues seriously restrict the further scalable application. Over the past few years, solid polymer electrolytes (SPEs) have been regarded as a promising alternative to address these challenges and facilitate the practical advancement of zinc batteries. In this review, we revisited the research progress of SPEs applied in zinc batteries in the past few years and focus on introducing cutting-edge polymer science and technologies that can be utilized to prepare advanced SPEs for high-performance zinc batteries. The operating mechanism of SPEs and the functions of polymers will be summarized. To highlight the polymer functions, SPEs are categorized into three types, respectively, homogenous polymer SPEs, hybrids polymer SPEs, and nanocomposites SPEs, which are expected to reveal the roles and principles of various polymers in zinc batteries. This review presents the current research progress and fundamental mechanisms of polymer-based SPEs in zinc batteries, outlines the challenging issues encountered, and meanwhile proposes potential solutions for future endeavours.

The emission of carbon compounds (in the form of soot) to the atmosphere has a significant impact on the environment and human health. Air pollution with combustion products, having a unique combination of physical and chemical properties, is an important component of very fine suspended dust, which is emitted from various sources related to combustion processes. The carbon compounds in the aerosol and deposited in the substrate are found all over the Earth. The paper presents results of comparative research on the content of 16 polycyclic aromatic hydrocarbons (PAHs) in soot samples obtained as a result of combustion of solid fuels such as hard coal with granulation above 60 mm, coal with a grain size of 25-80 mm, coal with a grain size of 8-25 mm, pellets and dry wood. On the basis of the conducted tests, it was found that the soot obtained in the combustion of coal in different granulation contains more cytotoxic PAHs in comparison to the combustion of wood pellets or dry firewood.

Table grape quality is of importance for consumers and thus for producers. The objective quality determination is usually destructive and very simple with the assessment of only a couple of parameters. This study proposed to evaluate the possibility of hyperspectral imaging to characterize table grapes quality through its sugar, total flavonoid and total anthocyanin contents. Different pre-treatments (WB, SNV, 1st and 2nd derivative) and different methods were tested: PLS with full spectra, then Multiple Linear Regression (MLR) were realized after selecting the optimal wavelengths thanks to the regression coefficients (-coefficients) and the Variable Importance in Projection (VIP) scores from the full spectra. All models were good showing that hyperspectral imaging is a relevant method to assess sugar content and global phenolic content. The best model was dependent on the variable. The best models were from the full spectra and with the 2nd derivative pre-treatment for TSS; from VIPs optimal wavelengths using SNV pre-treatment for Total Flavonoid and total Anthocyanin content. Thus, relevant models were proposed using the full spectra, as well as specific windows and wavelengths in order to reduce the data sets and limit the data storage to enable an industrial use.

A novel stationary phase for affinity separations is presented. This material is based on sintered borosilicate glass readily available as semi-finished filter plates with defined porosity and surface area. The material shows fast binding kinetics and excellent long-term stability under real application conditions due to lacking macropores and high mechanical rigidity. The glass surface can be easily modified with standard organosilane chemistry to immobilize selective binders or other molecules used for biointeraction. In this paper, the manufacturing of the columns and their respective column holders by 3D printing is shown in detail. The model system protein A/IgG was chosen as an example to examine the properties of such monolithic columns under realistic application conditions. Several specifications, such as (dynamic) IgG capacity, pressure stability, long-term performance, productivity, non-specific binding, and peak shape, are presented. It could be shown that due to the very high separation speed, 250 mg antibody per hour and column can be collected, which surpasses the productivity of most standard columns of the same size. The total IgG capacity of the shown columns is around 4 mg (5.5 mg/mL), which is sufficient for most tasks in research laboratories. The cycle time of an IgG separation can be less than 1 minute. Due to the glass material's excellent pressure resistance, these columns are compatible with standard HPLC systems. This is usually not the case with standard affinity columns, limited to manual use or application in low-pressure systems. The use of a standard HPLC system also improves the ability for automation, which enables the purification of hundreds of cell supernatants in one day. The sharp peak shape of the elution leads to an enrichment effect, which might increase the concentration of IgG by a factor of 3. The final concentration of IgG can be around 7.5 mg/mL without the need for an additional nanofiltration step. The purity of the IgG was > 95% in one step and nearly 99% with a second polishing run.

The primary goal of this review is to provide a comprehensive overview of the state-of-the-art in solid-state batteries (SSBs), with a focus on recent advancements in solid electrolytes and anodes. The paper begins with a background on the evolution from liquid electrolyte lithium-ion batteries to advanced SSBs, highlighting their enhanced safety and energy density. It addresses the increasing demand for efficient, safe energy storage in applications like electric vehicles and portable electronics. A major part of the paper analyzes solid electrolytes, key to SSB technology. It classifies solid electrolytes as polymer-based, oxide-based, and sulfide-based, discussing their distinct properties and application suitability. The review also covers advancements in anode materials for SSBs, exploring materials like lithium metal, silicon, and intermetallic compounds, focusing on their capacity, durability, and compatibility with solid electrolytes. It addresses challenges in integrating these anode materials, like interface stability and lithium dendrite growth. This review includes a discussion on the latest analytical techniques, experimental studies, and computational models to understand and improve the anode-solid electrolyte interface. These are crucial for tackling interfacial resistance and ensuring SSBs' long-term stability and efficiency. Concluding, the paper suggests future research and development directions, highlighting SSBs' potential in revolutionizing energy storage technologies. This review serves as a vital resource for academics, researchers, and industry professionals in advanced battery technology development. It offers a detailed overview of materials and technologies shaping SSBs' future, providing insights into current challenges and potential solutions in this rapidly evolving field.

Urination on carpet and subflooring can develop into persistent and challenging to mitigate odor. Very little or no information is published on how these VOCs change over time when urine is deposited on the carpet covering a plywood-type subflooring. This research has investigated the VOCs emitted from carpet+subflooring (control), carpet+subflooring sprayed with water (control with moisture), and cat urine-contaminated carpet+subflooring (treatment) over time (day 0 and 15). In addition, the effect of popular cleaning products on VOCs emitted and evaluated their efficacy in eliminating those indoor odors over time (day 0 and 15). Carpet-subflooring with all treatments were also contaminated with Micrococcus luteus, nonmotile obligate aerobe commonly found in household dust, to observe the impact of the aerobe on carpet-subflooring VOCs emission. VOCs emitted from carpet+subflooring receiving different treatments were collected from headspace using solid-phase microextraction (SPME). The VOCs were analyzed using a multidimensional gas chromatography-mass spectrometer attached to an olfactometry (GC-MS-O). Many common VOCs were released from the carpet on day one and day fifteen, specifically from urine contamination. Cleaning products were effective in masking several potent odors of cat urine contaminated carpet VOCs on day one but unable to remove the odor appeared on day 15 in most cases.

One of the biggest problems that the Dominican Republic has had in recent decades is the efficient management of solid waste produced by the population. This problem has worsened in recent years due to the decrease in available areas for the construction of sanitary landfills, the lack of recycling culture in the population, the deficiency in waste collection, and the scarce legal controls aimed at preserving water and air and soil, among other factors. The objective of this study was to explore the management of solid waste by the population and the municipality of Puñal, province of Santiago, to evaluate and analyze the situation and generation of solid waste, municipal solid waste management services, and the attitudes of the population regarding recycling projects and waste management, to evaluate the viability and sustainability of the use organic waste for energy generation. A total of 275 households from 29 localities in the municipality of Puñal were surveyed, which allowed for a significant population sample. According to the results obtained, the most significant type of waste produced by families is organic waste, followed by plastic waste and paper. Of the total organic waste produced in the municipality, 53% of solid waste is disregarded through the municipal waste collection system, while 47% is used as plant fertilizers or animal feed. On the other hand, most households receive the municipal waste collection service and pay for this service. The results of our research show that the implementation of an energy production system based on organic waste would be viable in the municipality of Puñal. However, a more efficient waste collection system would be necessary and the development of programs and projects that allow all households to participate in the system.

As a critical transmitter, the compact 532 nm lasers operating on high repetition and narrow pulse widths have been used widely for airborne or space-borne laser active remote sensing. We developed a free space pumped TEM₀₀ mode sub-nanosecond 532 nm laser that occupied a volume of less than 125 mm × 50 mm × 40 mm (0.25 liters). The fundamental 1064 nm laser consists of a passively Q-switched composite crystal microchip laser and an off-axis, two-pass power amplifier. The pump sources were two single-emitter semiconductor laser diodes (LD) of 808 nm with a maximum continuous wave (CW) power of 10 W each. The average power of fundamental 1064 nm laser was 1.26 W with the laser operating at 16 kHz repetition rates, and 857ps pulse widths. Since the beam distortion would be severe in microchip lasers in terms of the increase in heat load, for obtaining a high beam quality of 532 nm, the beam distortion was compensated by adjusting the distribution of pumping beam in our experiment of fundamental amplification. Furthermore, better than 0.6 W average power, 770 ps, beam quality of M² ＜1.2, and 16 kHz pulse output at 532 nm was obtained by a Type I LiB₃O₅ (LBO) crystal in the critical phase matching (CPM) regime for second harmonic generation (SHG).

Agriculture has been experiencing a difficult situation because of limiting factors in its production, Natural biostimulants (NBs) have emerged as a novel alternative. This study reviews NBs produced through Solid-State Fermentation (SSF) from organic waste, focusing on the processes and production methods. The aim is to highlight their potential for improving agricultural productivity and promoting sustainable agriculture. Through a literature review, the effects of NBS on crops were examined, as well as the challenges associated with their production and application. The importance of standardizing production processes, optimizing fermentation conditions, and assessing their effects on different crops is emphasized. Furthermore, future research areas are identified, such as enhancing production efficiency and evaluating the effectiveness of SSF-produced NBS in different agricultural systems. In conclusion, SSF-produced NBS offers a promising alternative for sustainable agriculture, but further research and development are needed to maximize its efficacy and enable large-scale implementation.

The co-electrolysis of CO2 and H2O at intermediate temperature is a viable approach for the power-to-gas conversion that deserves for further investigation, considering the need for green energy storage. The commercial solid oxide electrolyser is a promising device, but it is still facing to solve issues concerning the high operating temperatures and the improvement of gas value. In this paper we reported the recent findings of a simple approach that we have amply suggested for solid oxide cells consisting in the addition of a functional layer coated to the fuel electrode of commercial electrochemical cells. This approach simplifies the transition to the next generation of cells manufactured with the most promising materials currently developed and improves the gas value in the outlet stream of cell. Here, the material in use as a coating layer consisted of a Ni-modified La0.6Sr0.4Fe0.8Co0.2O3 which was developed and demonstrated as promising fuel electrode for solid oxide fuel cells. The results discussed in this paper proved the positive role of Ni-modified perovskite as a coating layer for the cathode, since an improvement of about twice was obtained about the quality of gas produced.

This paper seeks to examine how the Mn-Co spinel interconnect coating microstructure can in-fluence the Cr contamination in an oxygen electrode of intermediate temperature Solid Oxide Cells at the operating temperature of 750 °C. A Mn-Co spinel coating is processed on Crofer 22 APU substrates by electrophoretic deposition and subsequently sintered following both the one-step and two-step sintering, in order to obtain significantly different densification levels. The electrochemical characterization is performed on anode supported cells with a LSCF cathode. The cells were aged prior to the electrochemical characterization in contact with the spinel coated Crofer 22 APU at 750 °C for 250 hours. Current-voltage and impedance spectra of the cells were measured after the exposure with the interconnect. Post-mortem analysis of the interconnect and the cell was carried out in order to assess the Cr retention capability of coatings with different microstructures.

The formation of high-melting-point Cu₆Sn₅ interconnections is crucial to overcome the collapse of Sn-based micro-bumps and produce reliable intermetallic interconnections in three-dimensional (3D) package. However, because of the multiple reflows in 3D package manufacturing, Cu₆Sn₅ interconnections will experience the cyclic polymorphic transitions in the solid state. The repeated and abrupt change in the Cu₆Sn₅ lattice due to the cyclic polymorphic transitions can cause extreme strain oscillations, producing damages at the surface and in the interior of the Cu₆Sn₅ matrix. Moreover, because of the polymorphic-transition-induced grain splitting and superstructure phase formation, the reliability of Cu₆Sn₅ interconnections will thus face great challenges in 3D package. In addition, the Cu₆Sn₅ polymorphic transition is structure-dependent, and the η′↔η polymorphic transition will occur at the surface while the η′↔ηs↔η polymorphic transition will occur in the deep matrix. Our results can provide in-depth understandings of structural evolution and damage mechanism of Cu₆Sn₅ interconnections in real 3D package manufacturing.

Alterations in the carnitine shuttle system may be an indication of the presence of cancer. As such, in-depth analyses of this pathway in different malignant tumors could be important for the detec-tion and treatment of this disease. The current study aims to assess the profiles of carnitine and acylcarnitines in gliomas with respect to their grade, the presence of isocitrate dehydrogenase (IDH) mutations, and 1p/19q co-deletion. Brain tumors obtained from 19 patients were sampled on-site using solid-phase microextraction (SPME) immediately following excision. Analytes were desorbed and then analyzed via liquid chromatography-high resolution mass spectrometry. The results showed that SPME enabled the extraction of carnitine and 22 acylcarnitines. An analysis of the correlation factor revealed presence of two separate clusters: short-chain and long chain car-nitine esters. Slightly higher carnitine and acylcarnitine concentrations were observed in the higher malignancy tumor samples (high vs low grade), and in those samples with worse projected clinical outcomes (without vs with IDH mutation; without vs with 1p/19q co-deletion). Thus, the proposed chemical biopsy approach offers a simple solution for on-site sampling that enables sample preservation, thus supporting comprehensive multi-method analyses.

Tumor microenvironment (TME) represents a complex network between tumor cells and a variety of components including immune, stromal and vascular endothelial cells as well as extracellular matrix. A wide panel of signals and interactions here take place, resulting in a bi-directional modulation of cellular functions. Many stimuli, on one hand, induce tumor growth and spread of metastatic cells and, on the other hand, contribute to the establishment of an immunosuppressive environment. The latter feature is achieved by soothing immune effector cells, mainly cytotoxic T lymphocytes, B and NK cells, and/or through expansion of regulatory cell populations, including regulatory T and B cells, tumor-associated macrophages and myeloid-derived suppressor cells. In this context, immune checkpoints (IC) are key players in the control of T cell activation and anti-cancer activities, leading to the inhibition of tumor cell lysis and of pro-inflammatory cytokine production. Thus, these pathways represent promising targets for the development of effective and innovative therapies both in adults and childhood. Here we address the role of different cell populations homing the TME and of well-known and recently characterized IC in the context of pediatric solid tumors. We also discuss preclinical and clinical data available using IC inhibitors alone, in combination each other or administered with standard therapies.

As the global community shifts away from fossil fuels towards more environmentally friendly energy alternatives, there is an escalating demand for sophisticated energy storage solutions. Solid-State Batteries (SSBs) have emerged as a promising advancement, presenting a superior substitute to conventional lithium-ion batteries. This review provides an in-depth examination of SSBs, emphasizing their enhanced energy density, safety, and longevity. We evaluate conventional cathode materials, including lithium cobalt oxide (LiCoO2), lithium manganese oxide (LiMn2O4), and lithium iron phosphate (LiFePO4). Additionally, we introduce emerging materials such as sulfides, oxides, and air-based cathodes, discussing their benefits, limitations, and their congruence with solid electrolytes. Special attention is devoted to the structural fine-tuning of cathode ma-terials, investigating approaches like nanostructuring, surface coatings, and composite strategies to counteract issues such as restricted conductivity and structural volatility. The review critically analyzes the electrical and thermal properties of these materials, which are essential for battery safety and efficacy. Moreover, we present a comparative assessment of cathode materials based on performance indicators and identify prevailing research voids and hurdles in the commerciali-zation of SSB cathodes. Concluding, we suggest prospective research directions and innovations, underscoring the revolutionary potential of SSB technologies in paving the way for a sustainable energy horizon.

This study aimed to develop chitosan-based apigenin spray dried solid dispersion using 1:1,1:1.5,1:2 w/w ratios. The results of process yield and drug assay were found to be (87.5%, 94.2%, and 95.86%), (95.2 ±1.34%), (99.5 ±0.85%), and (97.6 ±2.42%), respectively, for AC1, AC2, and AC3. Flow properties indicate the free flow of powders. FTIR revealed compatibility among chitosan and apigenin, and DSC and XRD showed prepared solid dispersion was on a molecular level and available in amorphous. In contrast, SEM images reflect irregular block and near-spherical shape elongated particles in the selected AC2. The antimicrobial examination reflects that AC2 was more effective against Gram-positive, negative, and fungal strains. AC2 SDSDs has more anti-oxidant property compared to pure flavonoid (AGN). Anti-proliferative activity against A549 lung cancer cell lines showed better anti-cancer activity by AC2 SDSDs. The selected AC2 SDSD filled in a 3D shell pill and further characterized for 3D shell pill for dissolution profiles and stability studies. The product has sustained release and similar release profiles after three months of storage. The findings suggest that the AC2 SDSDs may be a promising candidate for further development as a 3D printed drug delivery system for treating multiple disease conditions using model flavonoid- apigenin.

Downwind odor characteristics can be very different depending upon the size of the upwind point-source, interim topography, and wind conditions. At one extreme, the downwind odor plume from a relatively large, confined animal feeding operation (CAFO), located on a flat open plain and under stable, near-straight-line wind conditions can be rather broad, sustained and predictable relative to a fixed receptor site downwind. In contrast, the plume from a small point-source (e.g., a roof vent stack) located on irregular topography and under rapidly shifting wind conditions can be intermittent and fleeting. These transient odor events can be surprisingly intense and offensive, in spite of their fleeting occurrence and perception. This work reports on efforts to optimize an environmental odor sampling strategy, which is optimized for the challenges of (1) sampling of such transient odor 'spikes' and (2) the prioritization of odors/odorants from multiple, closely co-located point-sources, under such transient event conditions. Protocol refinement has emerged by way of 2 environmental odor assessment projects which have been undertaken on behalf of the Missouri Department of Natural Resources. The challenge of transient odor events has been mitigated utilizing rapid, odor cued whole-air grab capture sampling into metalized-FEP gas sampling bags, followed by immediate adsorption transfer onto SPME fibers or sorbent tubes for stabilization during the shipment and storage interval between collection and final analysis. Initial results demonstrated approximately 11 fold increases in target odorant yields for 900 mL sorbent tube transfers from 2-3 second 'burst' odor event bag-captures, as compared to equivalent direct collections at the same downwind receptor location but during perceived (stable) odor 'lull' periods. Results-to-date targeting refinement and field trials of this integrated environmental odor assessment strategy are presented. Preliminary application targeting general odor sampling and point-source differentiation utilizing tracer gases is also presented.

The circular economy (CE) has emerged as a viable alternative for tackling the problems caused by rising consumption, including solid waste (SW). The present study conducted a meta-analysis of research published between 2012 and 2022 on CE and solid waste management (SWM). A bibliometric analysis was used from the Web of Science (WoS) and Scopus databases. By studying the articles, we briefly discussed the connections between them and how one contributes to the evolution of the other. Some findings point to greater collaboration between Italy and Bolivia, followed by China and Malaysia. However, they move away from the traditional axes as the United States and Canada. In addition, it was found that the adoption of reuse and selective collection, in fact, allow the reduction of the volume of discarded materials. In this way, it was possible to conclude that a greater connection between CE and GRS makes it possible to optimize the useful life of landfills through the treatment of organic waste and recycling, to encourage waste picker cooperatives and selective collection programs, and to reduce the financial costs of the system as a whole, making it more durable and sustainable.

Effective solid waste management is crucial for protecting public health and the environment. Global concentration on finding sustainable methods of handling waste continue to top the list of most governmental-related project checklists. This paper provides a case study on the management of municipal solid waste in the cities of Karlsruhe, Germany and Navrongo, Ghana as developed and developing countries respectively. This study aimed at comparing and drawing lessons from how these two different cities manage their solid waste. The waste management system in Karlsruhe prioritizes waste separation, recycling, and a pay-as-you-throw system has led to an efficient and sustainable waste management system that minimizes waste and protects the environment. Karlshrue's adoption of a continual developmental plan structure focused on integrated WM concepts is credited with safeguarding the long-term viability of waste management in the city. In contrast, Navrongo's waste management system faces several challenges, including inadequate resources and infrastructure, traditional waste disposal practices, and the lack of well-planned waste management strategies. To improve effective solid waste management systems in Ghana, a collaborative approach involving the government, local organizations, and the community is necessary. This can include investing in infrastructure, implementing waste separation and recycling programs, and educating the public on the benefits of sustainable waste management practices. Learning from successful models like Karlsruhe can help accelerate the development of sustainable waste management practices in Ghana, and ultimately protect public health and the environment.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

The goal of this work is to develop a sustainable value chain of carbonaceous adsorbents that can be produced from the solid fibrous digestate (SFD) of biogas plants and further applied in integrated desulphurisation-upgrading (CO2/CH4 separation) processes of biogas to yield high purity biomethane. On this purpose, physical and chemical activation of the SFD derived biochar was optimised to afford micro-mesoporous activated carbons (ACs) of high BET surface area (590-2300 m2g−1) and enhanced pore volume (0.57-1.0 cm3g−1). Gas breakthrough experiments from fixed bed columns of the obtained ACs, using real biogas mixture as feedstock, unveiled that the physical and chemical activation conclude to different types of ACs which are sufficient for biogas upgrade and biogas desulphurisation respectively. Performing breakthrough experiments at three temperatures close to ambient it was possible to define the optimum conditions for enhanced H2S/CO2 separation. It was also concluded that the H2S adsorption capacity is significantly affected by restriction to gas diffusion. Hence, the best performance was obtained at 50 oC and the maximum observed in the H2S adsorption capacity vs the temperature is attributed to the counterbalance between adsorption and diffusion processes.

Hong Kong is the biggest consumer of eggs in the world and ranks on the top with an average consumption of 24.52kg/capita/year. The egg consumption trend in Hong Kong has been increasing specifically; a drastic increase of about 100% has been observed from 2008 to 2020. One of the reasons behind this significant increase is the increase in the gross national income of Hong Kong in addition to the population growth rate. However, there was a slight decline in egg consumption trend in the year 2020 amid the COVID-19 pandemic. It has been estimated that there was a bulk of 17,100 tons of recoverable waste eggshells in 2019 (pre-COVID-19 situation), having a daily yield of 47 tons per day. Based on the linear regression, it may be expected that if the pre-COVID-19 trend of egg consumption remains sustained, there will be a big bulk of more than 45,000 tons per year and up to 125 tons per day of waste eggshells till 2050. In addition, a public survey was conducted across the city targeting individuals, families, and restaurants majorly on egg consumption and reuse. The survey outcomes revealed that Chinese eggs have an extensive market in Hong Kong, and people have a positive attitude towards eggshell recycling. Also, a massive population disposes of the waste eggshells while only a trace population reuses them. Therefore, Hong Kong has a very high potential to improve the circular economy by reusing waste eggshells on a commercial level in cementitious products.

A wide variety of applications require high peak laser intensity in conjunction with a narrow spectral linewidth. Typically, injection-locked amplifiers have been employed for this purpose, where a continuous wave oscillator is amplified in a secondary external resonant amplifier cavity using a pulsed pump laser. In contrast, here we demonstrate a setup that combines a CW Ti:sapphire oscillator and pulsed amplifier in a single optical cavity, resulting in a compact system. Dichroic beam combination of blue wavelength semiconductor diodes and the green wavelength of a Nd:YAG laser allowed the simultaneous excitation of the Ti:sapphire crystal by both continuous-wave and pulsed pump sources. A linewidth of <2MHz is achieved in continuous wave operation, while the linewidth increases to about 10MHz in the combined CW + pulsed mode with a pulse duration of 73ns. A peak pulse intensity of 0.2kW is achieved, which should enable efficient single-pass second harmonic generation in a nonlinear crystal.

The center of gravity of a three-dimensional object found through an experimental method can be made easier and faster than when calculating the movement manually in order to make the movement in computer graphic images look more natural. In addition, in various sports such as skating, the score can be increased by appropriately moving the position of the center of gravity. Lastly, it is expected that it can be used even when the performance is high in the manufacturing process to increase the stability and speed of various means of transportation (eg, automobiles, airplanes, etc.).

Hydrogenated amorphous silicon (a-Si:H) can be produced by plasma-enhanced chemical vapour deposition (PECVD) of SiH4 (Silane) mixed with Hydrogen. The resulting material shows outstanding radiation resistance properties and can be deposited on a wide variety of different substrates. These devices have been used to detect many different kinds of radiation namely: MIPs, x-rays, neutrons and ions as well as low energy protons and alphas. However, MIP detection using planar diodes has always been difficult due to the unsatisfactory S/N ratio arising from a combination of high leakage current, high capacitance and a limited charge collection efficiency (50% at best for a 30 µm planar diode). To overcome these limitations the 3D-SiAm collaboration proposes to use a 3D detector geometry. The use of vertical electrodes allows for a small collection distance to be maintained while conserving a large detector thickness for charge generation. The depletion voltage in this configuration can be kept below 400 V with consequent reduction in the leakage current. In this paper, following a detailed description of the fabrication process, the results of the tests performed on the planar p-i-n structures made with ion implantation of the dopants and with carrier selective contacts will be illustrated.

Peptide/Histidine Transporter PHT1 (SLC15A4) is expressed in lysosomal membranes of immune cells where it plays an important role in metabolic and inflammatory signaling. PHT1 is an H+-coupled/histidine symporter that can transport a broad range of oligopeptides, including a variety of bacterial-derived peptides. Moreover, it enables the scaffolding of various metabolic signaling molecules and interacts with key regulatory elements of the immune response. Therefore, it is not surprising that PHT1 is associated with the development of autoimmune diseases, such as systemic lupus erythematosus (SLE). Unfortunately, the pharmacological development of PHT1 has been hampered by the lack of appropriate transport assays. With the aim to address this shortcoming, a novel transport assay based on solid supported membrane-based electrophysiology (SSME) is presented. Key findings of the present SSME studies include the first recordings of electrophysiological properties, a pH dependence analysis, an assessment of PHT1 substrate selectivity, as well as the transport kinetics of the identified substrates. In contrast to previous works, PHT1 is studied its native lysosomal environment. Moreover, observed substrate selectivity is validated by molecular docking. Overall, this new SSME-based assay is expected to contribute to unlock the pharmacological potential of PHT1 and to deepen the understanding of its functional properties.

The isolation and potential applications of chitosan from the fungal source is an alternative to crustacean chitosan and synthetic polymers. The strains of Basidiomycota (Heterobasidion annosum, Phanerochaete chrysosporium, Pleurotus ostreatus, Trametes versicolor, Lentinus lepideus) with different environmental distribution, ecological importance, and industrial application were studied for mycelial biomass production in submerged (SF) and solid state fermentation (SSF). Further, the chitosan from fungal cells was extracted and characterized by elemental analyses (nitrogen) and FTIR spectroscopy. The fruiting bodies of Pleurotus ostreatus, Agaricus bisporus and Ganoderma ap-planatum were chosen as a reference material of chitosan content in basidiocarps. Stationary SF gave the lowest biomass yield in comparison with shaken SF and SSF. The role of aeration and agitation in biomass production was clearly observed in shaken SF with the highest yield achieved by P. chrysosporium. The highest biomass yield in SSF produced P. ostreatus and T. versi-color. The content of chitosan within fungal species varied depending on the method of cultiva-tion. The highest chitosan yield among the cultivated strains was obtained from mycelium of P. chrysosporium and T. versicolor in SF. The highest chitosan yield in fungal fruiting bodies demon-strated commercially cultivated mushroom A. bisporus. The extracted chitosan is proposed as functional biopolymer additive for ecological materials to substitute the synthetic wet and dry strength agents in packaging materials.

If a lubricant contains structures capable of conducting energy, reactions involving zinc dialkyldithiophosphate (ZDDP) may take place both very close to and away from the solid surfaces, with this indicating that ZDDP can be a highly effective anti-wear (AW) additive. The central thesis of this article is that the tribocatalytic effect is observed only when the energy emitted by the solids is transmitted by ordered molecular structures present in the lubricant, e.g., graphene. The friction tests were carried out for 100Cr6 steel balls in a sliding contact with uncoated or a:C-H-coated HS6-5-2C steel discs in the presence of polyalphaolefin 8 (PAO 8) as the lubricant, which was enhanced with graphene and/or ZDDP. There is sufficient evidence of the interactions occurring between ZDDP and graphene and their effects on the tribological performance of the system. It was also found that the higher the concentration of zinc in the wear area, the lower the wear. This was probably due to the energy transfer resulting from the catalytic decomposition of ZDDP molecules. Graphene, playing the role of the catalyst, contributed to that energy transfer.

Renewable active sludge is a smart material for wastewater treatment and the protection of surface water bodies. The generated pellets (dried and pelletised dehydrated anaerobically stabilised excess sludge) are produced in a quantity of 31.4 g ± 5.6 g dry matter (DM) per one Population equivalent (PE) calculated to COD (PE_COD) in one day. As pellets are combustible material, their energy utilisation must reach sustainable development goals (SDGs) - a bridge must be created between »treated sewage sludge as the tool to remove pollutants and nutrients from wastewater« and »preparation of the valuable material as a solid recovered fuel (SRF) that meets customer-specific requirements«. Technical Report CEN/TR 15508 and Technical Standard EN ISO 21640 set up methods for specifying and classifying pellets as an SRF. In the last eleven years (2010 – 2021), pellets' net calorific value (NCV) is 13.0 ± 0.7 MJ kg^-1 as received (ar). In 2021, the 80^th percentile of the Hg/NCV ratio was 0.079 mg Hg MJ^-1. In 2010 – 2021, the annual amount of Hg transferred to stakeholders reduced by 64.3 % m/m - from 10.1 kg to 3.67 kg. The halogen contents of the pellets do not threaten corrosion to the incineration facility. Stable pellets' energy potential and perspective ash composition for critical raw materials recovery qualify pellets as a specific waste stream and a renewable material for SRF production.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

During the novel coronavirus disease (COVID-19) pandemic, several environmental factors have influenced the activities and the protection policy measures. This has had a major effect on climate change and global environmental catastrophe. In many countries, the strategy of closing various activities such as tourism, industrial production, stopped normal life, transportation, among others. This closure has a positive impact on the environment. However, the massive use of masks and personal protection could significantly increase pollution worldwide. The impact on the environment needs to be calculated to have information for public health actions. In this study, we present a first overview of the potential impacts of COVID-19 on some environmental matrices in Bogota, Colombia.

White-rot fungi (WRF) have specific enzymes to degrade lignocellulosic and phenolic compounds. Therefore, their direct application could be an alternative to biodegrade complex lignocellulosic biomass such as olive mill solid waste (OMSW). The aim of this study was to evaluate the capacity of A. discolor and S. hirsutum to grow in OMSW as the sole substrate under static conditions and evaluate the phenolic removal compounds and lignin degradation. The lignolytic enzyme activity was determined, as was the phenolic compound removal. At the same time, lignin degradation and structural changes were evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscope (SEM), respectively. Both strains were able to grow using OMSW as the sole substrate without adding other nutrients, oxygen and/or agitation. The higher ligninolytic enzyme activity was found at day 8, and the highest phenolic removal (more than 80% with both strains) was reached after 24 days of incubation. The CLSM analysis confirmed lignin degradation through the drop in lignin fluorescence from 3967 for untreated OMSW to 235 and 221 RFU after 24 days of treatment by A. discolor and S. hirsutum respectively. The results indicate that both WRF could be suitable candidates to design an in-situ pretreatment step of OMSW, as long as in future research the WRFs have the same performance in non-sterile conditions.

Nigella sativa's thymoquinone (TQM), a water-insoluble phytonutrient exhibits nephroprotective effects. This study intends to develop a self-micellizing solid dispersion (SMSD) of TQM for better biopharmaceutical and nephroprotective performance. Soluplus®-based SMSD of TQM was created and tested for physicochemical properties, solubility, and pharmacokinetics in rats. Plasma creatinine, blood urea nitrogen (BUN), nephrotoxic indicators, and oxidative stress biomarkers were also tested. During SMSD preparation, TQM was found amorphous, boosting solubility. Minimal band changes between TQM and Soluplus® indicate insignificant drug-carrier interactions. SMSD-TQM generated fine micelles in water, improving TQM's solubility by 97.8% in 60 min. SMSD-TQM was 4.9 times more bioavailable orally in rats than crystalline TQM. In a rat model of acute renal damage by cisplatin (6 mg/kg, i.p.), SMSD-TQM (10 mg-TQM/kg, p.o.) reduced blood creatinine and BUN by 56% and 63.2%, respectively. These findings imply that SMSD-TQM may be a potent dosage option for enhancing TQM's nutrient value.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

Acute myeloid leukemia (AML) is an incurable hematological malignancy. To treat the disease successfully, new therapeutic strategies are urgently needed. One of these strategies can be the use of neurokinin-1 receptor (NK-1R) antagonists (e.g., aprepitant), because the substance P (SP)/NK-1R system is involved in cancer progression, including AML. AML patients show an up-regulation of the NK-1R mRNA expression; human AML cell lines show immunoreactivity for both SP and the NK-1R (it is overexpressed: the truncated isoform is more expressed than the full-length form) and, via this receptor, SP and NK-1R antagonists (aprepitant, in a concentration-dependent manner) respectively exert a proliferative action or an antileukemic effect (apoptotic mechanisms are triggered by promoting oxidative stress via mitochondrial Ca++ overload). Aprepitant inhibits the formation of AML cell colonies and, in combination with chemotherapeutic drugs, is more effective in inducing cytotoxic effects and AML cell growth blockade. NK-1R antagonists also exert an antinociceptive effect in myeloid leukemia-induced bone pain. The antitumor effect of aprepitant is diminished when the NF-κB pathway is overactivated and the damage induced by aprepitant in cancer cells is higher than that exerted in non-cancer cells. Thus, the SP/NK-1R system is involved in AML and aprepitant is a promising antitumor strategy against this hematological malignancy. In this review, the involvement of this system in solid and non-solid tumors (in particular in AML) is up-dated and the use of aprepitant as an anti-leukemic strategy for the treatment of AML is also mentioned (a dose of aprepitant (> 20 mg/kg/day) for a period of time according to the response to treatment is suggested).

Findings of new targeted treatments with adequate safety evaluations is essential for better cancer cures and mortality rates. Immunotherapy holds promise for patients with relapsed disease, with the ability to elicit long-term remissions. Emerging promising clinical results in B-cell malignancy using gene-altered T-lymphocytes uttering chimeric antigen receptors have sparked a lot of interest. This treatment could open the path for a major difference in the way we treat tumors that are resistant or recurring. Genetically altered T cells used to produce tumor-specific chimeric antigen receptors are resurrected field of adoptive cell therapy by demonstrating remarkable success in the treatment of malignant tumors. Because of the molecular complexity of chimeric antigen receptors -T cells, a variety of engineering approaches to improve safety and effectiveness are necessary to realize larger therapeutic uses. In this study, we investigate at new strategies for enhancing chimeric antigen receptors-T cell therapy by altering chimeric antigen receptors proteins, T lymphocytes, and their relations with other solid tumor microenvironment (TME) aspects.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

Nonporous corundum powder, known as an abrasive material in the industry, was functionalized covalently with protein binders to isolate and enrich specific proteins from complex matrices. The materials based on corundum were characterized by TEM, ESEM, BET, DLS, and zeta potential measurements. The strong Al-O-P bonds between the corundum surface and amino phosphonic acids are used to introduce functional groups for further conjugations. The common crosslinker glutaraldehyde was compared with a hyperbranched polyglycerol (PG) of around 10 kDa. The latter is oxidized with periodate to generate aldehyde groups that can covalently react with the amines of the surface and the amino groups from the protein via a reductive amination process. The amount of bound protein was quantified via aromatic amino acid analysis (AAAA). This work shows that oxidized polyglycerol can be used as an alternative to glutaraldehyde. With polyglycerol, more of the model protein bovine serum albumin (BSA) could be attached to the surface under the same conditions, and lower nonspecific binding (NSB) was observed. As a proof of concept, IgG was extracted with protein A from crude human plasma. The purity of the product was examined by SDS-PAGE. A binding capacity of 1.8 mg IgG per g of corundum powder was achieved. The advantages of corundum are the very low price, extremely high physical and chemical stability, pressure resistance, favorable binding kinetics, and flexible application.

Solid particles immersed in a fluid can be found in many engineering, environmental or medical fields. Applications are suspensions, sedimentation processes or procedural processes in the production of medication, food or construction materials. While homogenized behavior of these applications is well understood, contributions in the field of pore-scale fully resolved numerical simulations with non-spherical particles are rare. Using Smoothed Particle Hydrodynamics (SPH) as a simulation framework, we therefore present a modelling approach for Direct Numerical Simulations (DNS) of single-phase fluid containing non-spherically formed solid aggregates. Notable and discussed model specifications are the surface-coupled fluid-solid interaction forces as well as the contact forces between solid aggregates. The focus of this contribution is the numerical modelling approach and its implementation in SPH. Since SPH presents a fully resolved approach, the construction of arbitrary shaped particles is conveniently realizable. After validating our model for single non-spherical particles, we therefore investigate the motion of solid bodies in a Newtonian fluid and their interaction with the surrounding fluid by analyzing velocity fields of shear flow with respect to hydromechanical and contact forces. Results show a dependency of the motion and interaction of solid particles on their form and orientation. While spherical particles move to the centerline region, ellipsoidal particles move and rotate due to vortexes formation in the fluid flow in between.

Deposition/printing of materials with sub-1 μm precision and size (cross sections) is required for optical and electrical micro-devices. Crystalline c-ITO (Indium tin oxide) nanostructures were patterned on glass with a precision that formed gaps of 20-50 nm between individual disks or lines of ∼ 250 nm diameter or width. The absorbed energy density [J/cm3] followed the second order dependence on pulse energy. This facilitated high resolution and precision for nanoscale laser writing at the 515 nm laser wavelength. Patterns for optical elements such as circular gratings and micro-disks were laser printed using ITO as a resist. Unexposed amorphous a-ITO was chemically removed in aqueous 1% vol. HF solution. This use of a-ITO as solid-resist is promising for metamaterial and micro-optical applications.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

Mathematical modeling is the most important tool for constructing the theory of different kinds of two-phase flows. The review is devoted to the analysis of the advent of the approach of mathematical modeling of two-phase flows, where solid particles act mainly as the dispersed phase. The main problems and features of the study of gas-solid two-phase flows are excluded. The main characteristics of gas flows with solid particles are given and the classification of two-phase flows is developed on their basis. The Lagrangian and Euler approaches to modeling the motion of a dispersed phase (particles) are described. Much attention is paid to the consideration of numerical simulation methods that describe descriptions of turbulent gas flow at different hierarchical levels (RANS, LES, DNS), different levels of description of interphase interactions (one-way coupling (OWC), two-way coupling (TWC) and four-way coupling (FWC)), as well as at different levels of interface resolution (partial-point (PP) and particle-resolved (PR)). Excluded are examples of some studies carried out on the basis of the identified approaches, as well as their exclusion for mathematical modeling of various classes of gas-solid two-phase flows.

Chemotherapy for lung cancer has made remarkable progress, and its selection has been subdivided by genetic analysis. Although response evaluation criteria in solid tumors (RECIST) is a simple and highly objective evaluation method, it has been pointed out that it has the disadvantage of not being able to accurately evaluate the therapeutic effect of molecularly targeted drugs and immune checkpoint inhibitors. The purpose of this study is to determine whether quantitative evaluation of DWIBS is useful in determining the effectiveness of treatment for lung cancer. There were 31 patients with lung cancer and 56 patterns were obtained. First, the determination of treatment effect (PD, SD, PR) based on RECIST was performed on CT. Second, tDV and ADC (median) were measured using BD score from DWI images taken at the same time, and the rate of change was calculated. Then, we compared and examined the correlation between RECIST and the rate of change in tDV. There were correlations between RECIST and the rate of change in tDV in PD and PR cases respectively. Compared RECIST on CT, DWIBS using BD score would be more accurate for response evaluation of treatment. There was a tendency that tDV decreased with increasing ADC values, but some of the cases had a dissociated response with increasing ADC values and increasing tDV. Thus, since the color display of ADC values allows us to infer their contents, it would be useful for the evaluation of cases such as dissociated response and pseudoprogression, which are suspected to be atypical responses that are difficult to evaluate with RECIST and other methods.

Recently, there is a growing need for sensors that can operate autonomously, without the need for an external power source. This is especially important in applications where conventional power sources, such as batteries, are impractical or difficult to replace. Self-powered sensors have emerged as a promising solution to this challenge, offering a range of benefits such as low cost, high stability, and environmental friendliness. One of the most promising self-powered sensor technologies is L-S TENG, which stands for the liquid-solid triboelectric nanogenerator. This technology works by harnessing the mechanical energy generated by external stimuli such as pressure, touch, or vibration, and converting it into electrical energy that can be used to power sensors and other electronic devices. Therefore, self-powered based on L-S TENG, which provides numerous benefits such as rapidly responding, portability, cost-effectiveness, and miniaturization, is critical for increasing living standards and optimizing industrial processes. In this review paper, the working principle with three basic modes has been briefly introduced firstly. After that, affecting parameters to L-S TENG are reviewed based on the properties of the liquid and solid phases. With different working principles, L-S TENG has designed a lot of structure that works as a self-powered sensor for pressure/force change, liquid flow motion, concentration, and chemical detection or biochemical sensing. Moreover, the continuous output signal of TENG plays an important role in a real-time sensor that is vital to the growth of the Internet of Things.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

Environmental perception is a powerful tool for identifying community needs and potential within their surroundings. This study assessed tourists' environmental perception regarding solid waste and its impact on the Hurtado balneary, located in Valledupar, Colombia. From May to July 2023, the investigation delved into the environmental attitudes and behaviors of 769 balneary users by employing a combination of observation, photographic documentation, and a comprehensive 21-question online survey. The findings unveiled compelling insights: an overwhelming 98.8% of participants acknowledged the adverse effects of solid waste on the environment, with an impressive 98% demonstrating a willingness to participate in waste management efforts. Alarmingly, 42.13% exhibited limited awareness of waste management practices, reflecting a lack of public interest and commitment (41.61%). Statistically significant disparities emerged: 59% of waste items were not appropriately disposed of in designated receptacles. Reasons for this included a lack of a sense of belonging (50.2%) and inadequate environmental education (45.6%). 96% expressed the need for river conservation signage, while 59.8% had not engaged in environmental training. The implications of these results extend beyond the Hurtado balneary, potentially informing solid waste management strategies in other aquatic environments. Furthermore, this investigation aligns with three critical Sustainable Development Goals: SDG 12, emphasizing responsible consumption and production; SDG 13, addressing climate action; and SDG 15, advocating for life on land and below water. Keywords: Tourism; solid waste; surface water; environmental management.

The flavin derivatives 10‐methyl‐isoalloxazine (MIA) and 6-fluoro-10-methyl-isoalloxazine (6F-MIA) were encapsulated in two alternative metal-organic frameworks, (MOFs) MIL53(Al) and MOF5, using a post-synthetic, diffusion-based incorporation into microcrystalline MIL-53 powders and an in-situ approach during the MOF-5 synthesis. The flavin@MOF composites were analyzed by powder X-ray diffractometry (PXRD), N2-sorption studies and time-resolved fluorescence spectroscopy and microscopy. The maximum amount of flavin dye incorporation is 3.9 wt% for MIA@MIL-53(Al) and 1.5 wt% for 6F-MIA@MIL-53(Al), 0.85 wt% for MIA@MOF-5 and 27.6 wt% for 6F-MIA@MOF-5. The emission wavelengths of all flavin@MOF composites mostly correspond to the wavelengths of the flavins in solution. Time-resolved spectroscopy showed that the fluorescence lifetime of flavin@MOF of 2-4.7 ns also corresponds to those in solution but is significantly prolonged compared to the solid flavin dyes with less than 1 ns, thereby confirming the concept of "solid solutions" for dye@MOF composites. The fluorescence quantum yield (ΦF) of the flavin@MOF composites is about half of the solution but is significantly higher compared to the solid flavin dyes. Both the fluorescence lifetime and quantum yield of flavin@MOF decrease with the flavin loading in MIL-53. Theoretical calculations using plane-wave and QM/MM methods are in good correspondence with the experimental results and explain the electronic structures as well as the photoluminescence/photophysical properties of crystalline MIA and the flavin@MOF composites. In the solids flavins π-stacking interactions of the molecules lead to a charge transfer state with low oscillator strength resulting in aggregation-caused quenching (ACQ) with low lifetimes and quantum yields. In the MOF pores the flavin molecules are separated and the computed MIA@MOF structures do not find π-stacking interactions to the pore walls but only weak van-der-Waals contacts which reasons the enhanced fluorescence lifetime and quantum yield of the flavins in the composites compared to their neat solid state. The flexible MOF MIL-53(Al) was optimized essentially to the experimental large-pore form in the guest-free state with QuantumEspresso (QE) and with MIA molecules in the pores the structure contracted to close to the experimental narrow-pore form which was also confirmed by PXRD. In summary, the incorporation of flavins in MOFs yields solid-state materials with enhanced rigidity, stabilized conformation and reduced aggregations of the flavins, leading to increased fluorescence lifetime and quantum yield as controllable photo-luminescent and photo-physical properties.

Thin films of BiFeO3 (BFO), VO2 and BFO/VO2 were grown on SrTiO3(100) and Al2O3(0001) monocrystalline substrates using the RF and DC sputtering techniques. The surface of the films was characterized by profilometry, AFM, and XPS. The heterostructures have roughnesses between 0.2 and 16 nm and a grain size between 20 nm and 67 nm. XPS measurements show a higher proportion of the V4+ and Bi3+ oxides. In the Fe region, a higher proportion of Fe3+ is shown in the films. The homogeneous ordering, low roughnesses, and the oxidation states on the obtained surface show a good coupling in these films. The I-V curves show ohmic behavior at room temperature and change with increasing temperature. The effect of coupling these materials in a thin film shows the appearance of hysteresis cycles I-V and R-T, typical of materials with high potential in applications such as resistive memories and solar cells.

Oxygen and hydrogen mobility are among the important characteristics for operation of solid oxide fuel cells, permselective membranes and many other electrochemical devices. This, along with other characteristics, enables reaching a high power density of solid oxide fuel cells and a high oxygen or hydrogen permeation fluxes for membranes. This work focuses on oxygen and hydrogen diffusion of mixed ionic (oxide ionic or/and protonic) – electronic conducting materials for these devices and its role in the performance. Ionic transport properties of conventional and state-of-the-art materials are reviewed.

Transparent conductive electrodes (TCEs) are of enormous significance to the emergence of flexible and wearable electronics and continued growth of modern devices. Versatile and tunable TCEs, featuring with not only high optical transmittance but also intriguing features of electrochemical energy-storage capability, remain a significant challenge. Here we develop capacitive active films comprised of graphene-conjugated V2O5@poly (3,4-ethylene dioxythiophene) ternary composite (V2O5@PEDOT/rGO) on silver nanowire coated substrates as solid-state super/pseudocapacitors. The constructed electrodes exhibit improved electrolyte ions interaction with effective graphene layer, achieving high areal capacitance 0.6-1.2 mF.cm−2 with 0.5M LiCl electrolytes at optical transparency >60% with record durability. As demonstrated, the kinetic blocking of PEDOT layer and anchoring capability of graphene upon amphoteric soluble vanadium ions from layered V2O5 nanoribbons/nanobelts contribute synergistically to the unusual electrochemical stability, also shown using scanning electrochemical microscopy (SECM) providing electroactivity sites and ion transportation rates. As-fabricated symmetric solid-state supercapacitors delivered broad potential window >1.4 V under two different electrolyte environments (aqueous LiCl and LiCl/PVA gel) and demonstrated higher power and energy density (0.27 μWh.cm−2) outperforming previously reported devices at <0.1 μWh.cm−2. The electrochemical properties are also discussed in terms of solvation in polymer gel electrolyte ions.

The proton conductivity, phase composition and mechanical properties of (1-x)CsH2PO4–x fluoropolymer electrolytes (x-mass fraction, x=0-0.3) have been investigated firstly and discussed. UPTFE and PVDF-based polymers (F2M, F42, SKF26) with the high mechanical properties and thermal stability have been chosen as a fluoropolymer additive. According the XRD data, a monoclinic CsH2PO4 (P21/m) phase is retained in all compositions of the polymer electrolytes studied. The conductivity of (1-x)CsH2PO4-x fluoropolymer in the high-temperature phase decreases by approximately one order of magnitude compared with the pure CsH2PO4 for x~0.15-0.20. The size and shape of CsH2PO4 particles and their distribution have been shown to affect significantly the proton conductivity and mechanical properties of the membranes. The thin-film composite systems were produced by various methods of the obtaining salt particles, their mixing and applying to a polymer matrix. The uniform distribution of particles in the polymer systems with the size of ~300 nm was achieved by a pretreatment of the suspension in a bead mill. CsH2PO4-based mechanically strong membranes with the thickness ~50–100 μm were obtained for the soluble fluoropolymers (F2M, F42, SKF26). With an increase in the mass fraction of the polymer the ability of the membranes to resist the plastic deformation and the mechanical strength increases and comparable to the best low temperature membranes. The proton-conducting membranes (1-x)CsH2PO4 – x fluoropolymer with the optimal combination of the conductivity, mechanical and hydrophobic properties are promising for use in solid acid fuel cells.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

Viral infections can endanger public health by causing serious illness, leading to pandemics and burdening healthcare systems. Moreover, in the situation of a global spread, disruptions occur in every aspect of life including business, education, and social life. Fast and accurate diagnosis of viral infections has huge implications for saving people’s lives, preventing spread of the diseases, and minimizing social and economic damages. In the last decades, polymerase chain reaction (PCR) based techniques have been frequently used to detect viruses in the clinic. However, in a situation where rapid virus detection is the primary measure in preventing the spread, as in the case of ongoing COVID-19 pandemic, disadvantages of PCR, such as long processing times and requirement of sophisticated laboratory instruments, have been faced. Due to the urgent need for accurate techniques for virus detection, biosensor systems involved in many applications in biological detection are being developed for rapid, real-time, and high-throughput detection of viruses. Among various sensing platforms, optical devices are of great interest due to their advantages such as high sensitivity and direct readout. In the current review, usability of sensing techniques depending on optical phenomena, such as fluorescence-based sensors, surface plasmon resonance (SPR), surface enhanced Raman scattering (SERS), optical resonators and interferometry-based platforms, is discussed for virus diagnostics applications. Then, we focus on an interferometric biosensor developed by our group, single-particle interferometric reflectance imaging sensor (SP-IRIS), which has the capability to visualize single nanoparticles, to demonstrate its application for digital virus detection.

In this study, robust composite solid electrolytes were developed and employed them to enhance the performance of Li-metal batteries significantly. The robust composite solid electrolytes are composed of a soft polymer, poly(ethylene oxide), a Li salt, bis(trifluoromethanesulfonyl)imide (LiTFSI), and super ionic conductive ceramic fillers such as Li1.5Al0.5Ti1.5(PO4)3 (LATP), and Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The main goal of this study is to enhance the electrochemical stability and ionic conductivity. The ionic conductivities of the composite solid electrolytes were found to be 2.08 × 10-4 and 1.64 × 10-4 S cm-1 with the introduction of LATP and LLZTO fillers, respectively. The results prove that the fabricated solid electrolyte was electrochemical stable at voltage exceeding 4.25 V vs. Li/Li+. The internal resistance of the solid electrolyte significantly reduced as compare to gel electrolyte. This reduction can be attributed owing to the alleviation of bulk electrolyte, charge-transfer, and interfacial electrolyte/electrode impedance. When LiFePO4 cathode sheets are coated with a composite solid electrolyte containing LATP powders, the resulting Li-metal battery displays high capacity at 5 C (with a capacity retention of 65.2% compared to the original capacity at 0.2 C) as well as superior cyclic stability and excellent Coulombic efficiency (&gt; 99.5%, over 200 cycles). These results confirm that the composite solid electrolyte acts as a protective layer which have ability to prevent the growth of Li dendrites. Consequently, the fabricated electrolyte configuration can be engineered to enable high energy/power density and electrochemical stable cyclability in Li-metal batteries.

The battle of currents between AC and DC reignited as a result of the development in the field of power electronics. The efficiency of DC distribution systems is highly dependent on the efficiency of distribution converter, which calls for optimized schemes for efficiency enhancement of distribution converters. Modular solid-state transformers play a vital role in DC Distribution Networks and Renewable Energy systems (RES).This paper deals with efficiency-based load distribution for Solid State Transformers (SSTs) in DC distribution networks. Aim is to achieve a set of minimum inputs that are consistent with output while considering constraints and efficiency. As the main feature of modularity is associated with a three-stage structure of SSTs. This modular structure has been optimized using Ant Lion Optimizer (ALO) and validated by applying it EIA (Energy Information Agency) DC Distribution Network which contains SSTs. In the DC distribution grid, modular SSTs provide promising conversion of DC power from medium voltage to lower DC range (400V). The proposed algorithm is simulated in MATLAB and also compared with two other metaheuristic algorithms. The obtained results prove that the proposed method can significantly reduce input requirements for producing the same output while satisfying the specified constraints.

This scoping review examines global strategies and enterprises for sustainable solid waste management, with a focus on alternative landfilling approaches. The study collected and analyzed a significant number of documents from different regions, revealing Asia as the major contributor (for the collected documents) (48.7%), followed by North America (24.3%) and Europe (15.8%). Recycling emerged as the most effective alternative waste treatment method, representing 52.3% of the documented approaches, with industrial recycling (22.6%) and residential/non-residential recycling (20.2%) as prominent categories. Food waste was a significant concern across regions, constituting 21.4% of the collected documents. Composting was widely adopted (15.4%) due to its simplicity and benefits for gardening and soil improvement. Other methods like biogas extraction, reusing, raising awareness, incinerating, redistributing, reducing, and fermentation accounted for 13.1% cumulatively. The study highlights the need for tailored waste management solutions based on regional challenges and successful practices. Promoting recycling infrastructure, composting, and waste reduction approaches are crucial to achieving sustainable waste management aligned with SDGs. Collaboration and knowledge-sharing between regions are essential to improve inefficient waste management mechanisms. Integrating the findings into policymaking and industry practices can lead to a more sustainable future with reduced environmental impact.

SAMHD1 is a deoxynucleotide triphosphate (dNTP) triphosphohydrolase with important roles in the control of cell proliferation and apoptosis, either through the regulation of intracellular dNTPs levels or the modulation of the DNA damage response. However, SAMHD1 role in cancer evolution is still unknown. We performed the first in-depth study of SAMHD1 role in advanced solid tumors, by analyzing samples of 128 patients treated with chemotherapy agents based on platinum derivatives and/or antimetabolites and developing novel in vitro knock-out models to explore the mechanisms driving SAMHD1 function in cancer. Low or no expression of SAMHD1 was associated with a positive prognosis in breast, ovarian and non-small cell lung cancer (NSCLC) cancer patients. A predictive value was associated to low-SAMHD1 expression in NSCLC and ovarian patients treated with antimetabolites in combination with platinum derivatives. In vitro, SAMHD1 knock-out cells showed increased γ-H2AX and apoptosis suggesting that SAMHD1 depletion induces DNA damage leading to cell death. In vitro treatment with platinum-derived drugs significantly enhanced γ-H2AX and apoptotic markers expression in knock-out cells, indicating a synergic effect of SAMHD1 depletion and platinum-based treatment. SAMHD1 expression represents a new strong prognostic and predictive biomarker in solid tumors and thus, modulation of SAMHD1 function may constitute a promising target for the improvement of cancer therapy.

Solid asperity interactions are common and inevitable under severe loading conditions for any lubricated contact. Heavy-duty machine components (gear, bearings etc.) generally operate under Mixed Lubrication, where uneven surface features contact each other when generated fluid pressure is not enough to support the external load. The Reynolds equation is commonly used to simulate smooth lubricated contacts numerically. In rough lubricated interfaces where opposite surface asperities make contact, the Reynolds equation alone cannot accurately predict pressure using the traditional numerical simulation method. In this paper, Lubrication-Contact interface conditions (LCICs) have been implemented and extended to solve the multiple asperity contact problem using the full-multigrid approach. The developed novel algorithm has significantly accelerated the solution process and improved the accuracy and efficiency of pressure calculation for fluid-solid sub-interactions that can occur under ML regions. The Finite Difference Method (FDM) results have been compared with Computational Fluid Dynamics (CFD) simulation to validate the newly developed model. Hence, the proposed optimized solution method will provide valuable insight to researchers and industry engineers interested in simulating the ML problem where the effect of the fluid-solid interface can be captured effectively to improve reliability in the calculation of the life expectancy of the lubricated parts.

Scientific advancements in the food industry have resulted in the discovery of natural substances that can serve various functions in food. Essential oils, in particular, can act as food preservatives or flavoring agents due to their abundance of natural antioxidants, which possess preservative properties. In this study, the composition of Thymus vulgaris essential oil was determined using GC-MS and HS-SPME. The essential oil obtained from Thymus vulgaris L. through hydro-distillation yielded approximately 4%. GC/MS analysis of the essential oil identified 11 components, with a predominant presence of oxygenated monoterpenes (56.97%). Notably, carvacrol (37.63%) and thymol (17.35%) were present in significant amounts, accounting for 54.98% of the overall composition. The in vitro antioxidant activity of the essential oil was evaluated using three methods. The DPPH free radical scavenging test yielded an IC50 of 0.51±0.11 mg mL-1. The β-carotene/linoleic acid bleaching test resulted in an IC50 of 2.58±0.10 mg mL-1. Finally, the ABTS assay indicated relatively lower antioxidant activity compared to ascorbic acid.

Environmental degradation is one of the most visible problems in Hargeisa. Currently, solid waste is disposed of at two dumping sites within the city limits causing nuisance and unsanitary conditions. Moreover, the existing dumpsites are on the verge of closure, therefore necessitating a dire need to be addressed. This research paper is aimed to integrate multicriteria decision analysis and GIS for evaluating the site suitability for the landfill in Hargeisa, Somaliland. For this purpose, eleven significant parameters were selected: proximity from built-up areas, surface water, groundwater well points, sensitive sites (Airports), land use/land cover, geology, soil type, elevation, slopes, roads, and distance to existing dumpsites. These were then integrated using an analytical hierarchy process (AHP). Subsequently, restriction buffer analysis was performed on the seven parameters to obtain better and more accurate results, and restricted zones were omitted. Furthermore, the pair-wise comparison used to obtain priorities between the selected criteria showed that the land uses land cover is the most significant criterion in the model with a relative weight of 0.1829, followed by the habitations, 0.1506. The overall result reveals that about 68.96% (21060.9 ha) of the study area is unsuitable, while 24.36% (7441.53 ha) and 6.68% accounted for the less and highly appropriate zone, respectively. Following the results of this study, Hargeisa City's municipal council must reconsider the waste management and landfill sites to solve the problems observed in the area before it is overdue. Furthermore, this systematic research approach will assist regional and global researchers, policymakers, and municipal governments.

Garnet-type Ta-doped Li7La3Zr2O12 (LLZO) ceramic solid electrolytes with Ga2O3 additive were synthesized via a conventional solid-state reaction process. When the amounts of Ga2O3 additive were below 2 mol %, the sintered sample has a dense structure composed of grains with the averaged size of 5 to 10 μm, while 3 mol % or more Ga2O3 addition causes the significant increase in grain size above several 10 to 100 μm, due to the sintering with large amount of liquid Li-Ga-O phase at high temperature. The highest total (bulk + grain-boundary) ionic conductivity of 1.1 mS cm1 at room temperature was obtained in the sample with 5 mol % Ga2O3 addition. However, in galvanostatic testing of the symmetric cell with Li metal electrodes, this sample was shorted by Li dendrite growth into solid electrolyte at current density below 0.2 mA cm2. The tolerance for Li dendrite growth is maximized in sample sintered with 2 mol % Ga2O3 addition, which was shorted at 0.8 mA cm2 in the symmetric cell. Since the interfacial resistance between Li metal and solid electrolyte was nearly identical among the all samples, the difference in tolerance for Li dendrite growth is mainly attributed to the difference in microstructure of sintered samples depending on the amounts of Ga2O3.

In this paper the application of the solid-state cooling based on barocaloric effect in the cold food supply chain is investigated. Barocaloric solid-state technology is applied to the final chain links of the cold food supply chain, regarding the steps of retail and domestic conservation. In this context a barocaloric cooler with regard to food needing to be kept at 5°C (273 K), in order to operate with a promising cooling technology that result energy efficient and environmentally friendly. The categories of food interested in the investigation are meets and fresh food products like soft cheese, yogurt, milk. The energy performances of the barocaloric system have been carried out and compared with a commercial vapor compression refrigerator of a similar size, both operating with R600a under the same working conditions. Basing on the following consideration one can conclude that barocaloric cooling is a favourable technology to be employed in the last link chains of the cold food supply chain if the system operates in ABR cycle at frequencies between 1.25 and 1.50 Hz with a regenerator made of acetoxy silicone rubber as solid-state refrigerant and 50%EG-50%water mixture as heat transfer fluid flowing at the optimal velocity of 0.15 m s-1 that guarantees an appropriate trade-off between the temperature span, the cooling power and the coefficient of performances. Under these conditions the barocaloric system overperforms the domestic vapor compression cooler operating with R600a.

Personal Information Management Systems (PIMS) are acquiring a prominent role in the data economy by promoting services that help individuals to have more control over the processing of their personal data, in line with the European data protection law. One of the highlighted solutions in this area is Solid, a new protocol that is decentralizing the storage of data, through the usage of interoperable Web standards and semantic vocabularies, to empower its users to have more control over the processing of data by agents and applications. However, to fulfill this vision and gather widespread adoption, Solid needs to be aligned with the law governing the processing of personal data in Europe, the main piece of legislation being the General Data Protection Regulation (GDPR). To assist with this process, we analyze the current efforts to introduce a policy layer in the Solid ecosystem, in particular, related to the challenge of obtaining consent for processing personal data, focusing on the GDPR. Furthermore, we investigate if, in the context of using personal data for biomedical research, consent can be expressed in advance, discuss the conditions for valid consent and how it can be obtained in this decentralized setting, namely through the matching of privacy preferences, set by the user, with requests for data and whether this can signify informed consent. Finally, we discuss the technical challenges of an implementation that caters to the previously-identified legal requirements.

The present study was designed to develop a self-micellizing solid dispersion (SMSD) containing Thymoquinone (TQM), a phytonutrient obtained from Nigella sativa seeds, aiming to improve its biopharmaceutical and nephroprotective functions. The apparent solubility of TQM in polymer solutions was used to choose an appropriate amphiphilic polymer that could be used to make an SMSD system. Based on the apparent solubility, Soluplus® was chosen as an appropriate carrier, and mixing with TQM, SMSD-TQM with different loadings of TQM (5–15%) was made by solvent evaporation and freeze-drying techniques, respectively, and the formulations were optimized. The optimized SMSD-TQM was evaluated in terms of particle size distribution, morphology, release characteristics, pharmacokinetic behavior, and nephroprotective effects in a rat model of acute kidney injury. SMSD-TQM significantly improved the dissolution characteristics (97.8%) of TQM in water within 60 min. Oral administration of SMSD-TQM in rats exhibited a 4.9-fold higher systemic exposure than crystalline TQM. In a cisplatin-induced (6 mg/kg, i.p.) acute kidney-damaged rat model, oral SMSD-TQM (10 mg/kg) improved the nephroprotective effects of TQM based on the results of kidney biomarkers and histological abnormalities. These findings suggest that SMSD-TQM might be efficacious in enhancing the nephroprotective effect of TQM by overcoming biopharmaceutical limitations.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

The complete regression of clear cell renal cell carcinoma (ccRCC) obtained pre-clinically with anti-carbonic anhydrase IX (CAIX) G36 chimeric antigen receptor (CAR) T cells in doses equivalent to 10e8 CAR T cells/ Kg renewed the potential of this target to treat ccRCC and other tumors in hypoxia. The immune checkpoint blockade (ICB) brought durable clinical responses in advanced ccRCC and other tumors. Here we tested CD8/4-1BB compared to CD28-based anti-CAIX CAR PBMCs cells-releasing anti-programmed cell death ligand-1 (PD-L1) IgG4 for human ccRCC treatment in vitro and in an orthotopic NSG mice model in vivo. Using a 10e7 CAR PBMCs cells/ Kg dose, anti-CAIX CD28 CAR T cells releasing anti-PD-L1 IgG highly decrease both tumor volume and weight in vivo, avoiding the occurrence of metastasis. This antitumoral superiority of CD28-based CAR PBMCs cells compared to 4-1BB occurred under ICB via PD-L1. Furthermore, T cell exhaustion status in peripheral CD4 T cells, additionally to CD8 was critical for CAR T cells efficiency. The lack of hepatotoxicity and nephrotoxicity upon administration of 10e7 CAR PMBCs cells/Kg dose is the basis for carrying out clinical trials using anti-CAIX CD28 CAR PBMCs cells releasing anti-PD-L1 antibodies or anti-CAIX 4-1BB CAR T cells, offering exciting new prospects for the treatment of refractory ccRCC and hypoxic tumors.

One of the possible mechanisms causing significant emissions of methane into the atmosphere within the Arctic shelf may be the decomposition of gas hydrates. Their accumulations within the Arctic shelf formed during Ice Age almost simultaneously with the formation of permafrost, which contributed to the emergence of a zone of stable existence of gas hydrates. The subsequent flooding of the Arctic shelf led to the degradation of the permafrost and the violation of the conditions for the existence of hydrates. To assess the state of the stability zone, methods of mathematical numerical modeling are used. Standard seismic methods are widely used to localize gas hydrates, but monitoring their physical state requires the development of fundamentally new approaches based on solving multiparameter inverse seismic problems. In particular, the degree of attenuation of seismic energy is one of the objective parameters for assessing the consolidation of gas hydrates: the closer they are to the beginning of decomposition, the higher the attenuation, and hence the lower the quality factor. Thus, the methods of seismic monitoring of the state of gas hydrates in order to predict the possibility of developing dangerous scenarios should be based on solving a multi-parameter inverse seismic problem. This publication is devoted to the presentation of this approach.

This review provides an overview of the biotransformation of limonene and α-pinene, which are commonly found in wood residues and citrus fruit by-products, to produce high-value-added products. Essential oils derived from various plant parts contain monoterpene hydrocarbons, such as limonene and pinenes which are often considered waste due to their low sensory activity, poor water solubility, and tendency to autoxidize and polymerise. However, these terpene hydrocarbons serve as ideal starting materials for microbial transformations. Moreover, agro-industrial byproducts can be employed as nutrient and substrate sources, reducing fermentation costs, and enhancing industrial viability. Terpenes, being secondary metabolites of plants, are abundant in byproducts generated during fruit and plant processing. Microbial cells offer advantages over enzymes due to their higher stability, rapid growth rates, and genetic engineering potential. Fermentation parameters can be easily manipulated to enhance strain performance in large-scale processes. The economic advantages of biotransformation are highlighted by comparing the prices of substrates and products. For instance, R-limonene, priced at US$34/L, can be transformed into carveol, valued at around US$530/L. This review emphasises the potential of biotransformation to produce high-value products from limonene and α-pinene molecules, particularly present in wood residues and citrus fruit by-products. The utilisation of microbial transformations, along with agro-industrial byproducts, presents a promising approach to extract value from waste materials and enhance the sustainability of the antimicrobial, the fragrance and flavour industry.

Near-neutral pH and low redox potentials (EH) are considered favorable conditions for radionuclides immobilization in deep repository systems in clay geological formations. Cigeo is a future Industrial Centre for Geological Disposal for Nuclear Waste (NW) for high-level and intermediate level long-lived radioactive waste, to be built in France, at 500 m depth within the Callovo-Oxfordian clay formation. Deep knowledge of the mechanisms and kinetics of corrosion occurring at the external surface of tubings made of API 5L X65 carbon steel (CS-X65) in contact with COx pore water, is essential for a reversible NW management of the Cigeo site. By using robust handmade electrodes and electrochemical and gravimetric techniques, this work aimed to determine the corrosion phenomenology and kinetics of CS-X65 in contact with COx pore water flowing continuously through a Multi-Parameter Probe (MPP) device, placed at 500 m depth, for more than 180 days. It also aimed at demonstrating the reliability and the robustness of the measurement methodology for the corrosion evaluation of the metallic liner of the future nuclear waste disposal site. Two iron oxidants were encountered, oxygen, who was depleted, and proton, who was accompanied by hydrogen sulfide. Corrosion mechanisms and kinetics were well established for two CS-X65, electrochemically perturbed and not. The corrosion thickness loss rates stand between 0.016 and 0.032 mm/y.

This review provides an extensive overview of the developments in the field of polymer science, focusing on the solid-state modification (SSM) of thermoplastic materials. The background of the study places thermoplastics within the context of their increased use over the past century, highlighting their versatility in various applications and the associated environmental and health concerns due to certain additives. The methods section delves into the specifics of SSM, a technique that involves the incorporation of monomers or oligomers into the amorphous phase of polymers through multiple exchange reactions, distinguishing it from traditional melt polymer modification methods. The results section outlines the unique aspects of SSM and its increasing recognition for its potential to enhance material performance in areas such as catalysts and composites. It also discusses the application of SSM in modifying different thermoplastic polymers, highlighting various studies demonstrating the method's effectiveness in altering polymer properties. Finally, this work emphasizes SSM's importance in environmental sustainability and its potential in the recycling and upcycling of plastic materials. It acknowledges the challenges and future perspectives in the field, particularly regarding the scalability of SSM techniques for industrial applications and their role in advancing a circular economy in the polymer industry.

Despite the fact that strong routine separation methodologies can give reliable specificity and validity at usual working pharmaceuticals concentrations, they may fail at very low concentration levels. This poses considerable challenges for researchers inves-tigating product purity and therapeutic drug monitoring. Sensitivity enhancement pro-cedures are thus required to maximize the performance of separation techniques. Large volume injection, solid phase extraction/solid phase enrichment (SPE/SPEn), pre-, post-, and in-column derivatization, as well as the use of sensitive detection devices are the simplest strategies for improving sensitivity of the separation-based analytical techniques. Large volume injection of samples with online SPE/SPEn coupled with separation techniques increased sensitivity and improved detection as well as quantification limits without affecting peak shape and system performance. Although the primary purpose of derivatization is to improve sensitivity and selectivity, greener derivatization is growing in popularity and should be considered in analytical chemistry. In general, two strategies are essential for accomplishing greener derivatization goals. The first is the search for and use of ecologically acceptable derivatizing reagents, solvents, and reaction conditions. The second is miniaturization and automation of analytical methods. This review discusses significant advances in separation-based analytical techniques, specifically enrichment approaches and detector signal improvement for pharmaceutical quantification in various matrices at very low concentration levels. As a result of improved analytical systems setup in drug assays, the possibility of high-throughput analyses was also highlighted.

Childhood malnutrition is one of the most persistent public health problems throughout developing countries including Nigeria. This study focused on the evaluation of complementary food produced by solid-state fermentation of Fonio and Soybean using Rhizopus oligosporus (2710) and Orange-fleshed sweet potatoes (OFSP) using Lactobacillus planterum, (B-41621). Solid state fermentation (SSF) was carried out by inoculating Fonio and Soybean with spore suspension (1×10⁶spores/ml) of Rhizopus oligosporus (2710) and OFSP with spore suspension (1×10⁶spores/ml) of Lactobacillus planterum (B-41621). The samples were blended in the following ratios: Fonio and Soybean 100: 100 (AS), fonio/soybean and OFSP 50: 50(ASO), and compared with a commercial infant formula which served as the control (CTRL). Quality characteristics of the samples were evaluated. Results showed that moisture, crude protein, fibre, ash content, beta carotene and titratable acidity increased significantly (p<0.05) as fermentation progressed. The iron content ranged from 6.57–8.41mg/100g while the beta carotene content ranged from 15.80 –17.35mg/100g. Viscosity ranged from 8200 –15400cP, while that of swelling capacity ranged from 2.25-3.41(g/g). In sensory scores, there were no significant (p>0.05) difference between the average mean scores of the samples. SSF improved the nutritional content and flavour of the developed complementary food which is needed for infant growth and development.

Eric Lord has observed: “In nature, helical structures arise when identical structural subunits combine sequentially, the orientational and translational relation between each unit and its predecessor remaining constant.” This paper proves Lord’s Observation. Constant-time algorithms are given for the segmented helix generated from the intrinsic properties of a stacked object and its conjoining rule. Standard results from screw theory and previous work are combined with corollaries of Lord’s observation to allow calculations of segmented helices from either transformation matrices or four known consecutive points. The construction of these from the intrinsic properties of the rule for conjoining repeated subunits of arbitrary shape is provided, allowing the complete parameters describing the unique segmented helix generated by arbitrary stackings to be easily calculated. Free-libre open-source interactive software and a website is provided which performs this computation for arbitrary prisms along with interactive 3D visualization . We prove that any subunit can produce a toroid-like helix or a maximally-extended helix, forming a continuous spectrum based on joint-face normal twist. This software, website and paper, taken together, compute, render, and catalog an exhaustive “zoo” of 28 uniquely-shaped platonic helices, such as the Boerdijk-Coxeter tetrahelix and various species of helices formed from dodecahedra.

CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &amp;0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

An inorganic solid electrolyte is the most favorable candidate for replacing flammable liquid electrolytes in lithium batteries. Lithium Lanthanum Zirconium Oxide (LLZO) is considered as a promising solid electrolyte due to its safe operating potential window (0-5V) combined with its good electrochemical stability. In this work, 250 g batches of pre-sintered Tadoped (Li7La3Zr1.6Ta0.4O12, TaLLZO) were synthesized for bulk production of dense LLZO electrolyte. A simple two-step thermal treatment process was developed. The first thermal step at 950 °C initiates nucleation of LLZO carefully controlling process parameters such as heating atmosphere, temperature and dopant concentration. In the second thermal step at 1150 °C, sintered discs were obtained as solid electrolytes, with relative densities of 96%. X-ray diffraction analysis confirmed the phase purity of the sintered TaLLZO disc, and refined data was used to calculate the lattice parameter (12.944 Å). Furthermore, the presence of the Ta dopant in the disc was confirmed through X-ray photoelectron spectroscopy (XPS) analysis. The ionic and electronic conductivity values of TaLLZO disc were 104 S cm-1 and 10-10 S cm-1, respectively. These values confirm that the prepared (Ta-LLZO) discs exhibit ionic conductivity while being electronically insulating, being suitable for use as solid electrolytes with the requisite electrical properties.

Contacting bodies in extreme environments are prone to severe wear and failure due to friction and seizure, which are associated with significant thermal and mechanical loads. This phenomenon greatly impacts the economy since most essential components encounter these challenges during machining, an unavoidable step in most manufacturing processes. In machining, stress can reach 4 GPa, and temperatures can exceed 1000 °C at the cutting zone. Severe seizure and friction are the primary causes of tool and workpiece failures. Liquid lubricants are popular in machining for combatting heat and friction; however, concerns about their environmental impact are growing, as two-thirds of the 40 million tons used annually are discarded and they produce other environmental and safety issues. Despite their overall efficacy, these lubricants also have limitations, including ineffectiveness in reducing seizure at the tool/chip interface and susceptibility to degradation at high temperatures. There is therefore a push towards solid lubricants, which promise a reduced environmental footprint, better friction management, and improved machining outcomes but also face challenges under extreme machining conditions. This research aims to provide a thorough insight into solid lubricant use in machining, discussing their mechanisms, effectiveness, constraints, and potential to boost productivity and environmental sustainability.

Abstract: Pomegranate peels are important source of polyphenols with remarkable interest in food, pharmaceutical and cosmetic industry. An improved extraction of total polyphenolic com-pounds (TPC) from pomegranate peels by Solid-State Fermentation (SSF) was achieved. A Box Hunter & Hunter (BHH) followed by Central Composite Design (CCD) were performed to assess the effect of the process variables on TPC release. The statistic designs indicate that the best TPC extraction (234.85 mg GAE/gdm) by means of SSF occurs, at 42°C, 50 % moisture, pH 5.0, mineral solution (g/L): NaNO3 (3.83), KH2PO4 (1.52), MgSO4 (4.66) and KCl (1.52) at 36 h. At the best fer-mentation conditions, TPC (248.78±1.24 mgGAE/gdm) increased 5.96-fold than values previously reported and antioxidant activity [AA] increased 5.81-fold than the value obtained before the SSF optimization. High-valued citric acid, α and β punicalin, α and β punicalagin, punigluconin, gal-loyl-HHDP hexoside and ellagic acid molecules were identified. The increased extraction of TPC by SSF provides a suitable alternative for pomegranate peels valorization through the re-covery of molecules with high added value with potential use in food, pharmacy and cosmetic industries; a diversification in the use of food agroindustry by-products is obtained as approach to the circular economy model through biotechnological processes.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

Background: Chronic kidney disease (CKD) is a common complication of non-kidney solid organ transplant (NKSOT). Identifying predisposing factors is crucial for an early approach and correct referral to nephrology. Methods: This is a single-center retrospective observational study of a cohort of CKD patients under follow-up in Nephrology Department between 2010 to 2020. Statistical analysis was performed between all the risk factors and four dependent variables: end-stage renal disease (ESKD), increased serum creatinine ≥50%, renal replacement therapy (RRT), and death in pre-transplant, peri-transplant and post-transplant period. Results: 74 patients were studied (7 heart transplant, 34 liver transplants, and 33 lung transplant). Patients who were not followed-up by nephrology in the pre-transplant (p&lt;0.027), peri-transplant (p&lt;0.046), and the longest time until outpatient clinic follow-up (HR 1,032) were associated with a higher risk of creatinine increase ≥50%. Receiving a lung transplant conferred higher risk than liver or hear transplant for developing a creatinine increase ≥50% and ESKD. Peri-transplant mechanical ventilation, peri-transplant and post-transplant anticalcineurin overdose, nephrotoxic and the number of hospital admissions were significantly associated to present a creatinine increase ≥50% and develop ESKD. Conclusion: An early follow-up by the nephrology department was associated with a decrease in the worsening of renal function.

Prevention of infections is crucial in solid organ transplant (SOT) candidates and recipients. These pa-tients are exposed to an increased infectious risk due to previous organ insufficiency and to pharmaco-logic immunosuppression. Besides infectious-related morbidity and mortality, this vulnerable group of patients is also exposed to the risk of acute decompensation and organ rejection or failure in the pre- and post-transplant period respectively, since antimicrobial treatments are less effective than in the immunocompetent patients. Vaccination represents a major preventive measure against specific infec-tious risks in this population but as responses to vaccines are reduced, especially in the early post-transplant period or after treatment for rejection, an optimal vaccination status should be obtained prior to transplantation whenever possible. This review reports the currently available data on the indications and modalities of vaccination in SOT adult candidates and recipients.

Since there are no morphological clues capable of making a pathologist suspect a possible mammary origin of a metastatic lesion without adequate clinical information, the histologic diagnosis of brain metastasis from BC is still based on the immunohistochemical expression of mammary gland markers such as GATA-3, ERs, PgRs and HER-2. The present retrospective study aimed to select purely morphological features capable to suggest the mammary origin of a metastatic carcinoma to the brain. The following histological features were collected on a series of 30 cases of brain metastases from breast cancer:(i) solid growth pattern; (ii) presence of comedonecrosis; (iii) glandular differentiation. Our results showed that most cases histologically exhibited solid growth pattern with at least focal comedonecrosis, producing an overall morphology closely reminiscent of mammary high-grade ductal carcinoma in situ. Although the above-mentioned morphological parameters are not strictly specific to a mammary origin, they may have an important diagnostic utility in leading pathologists to suspect a possible breast primary tumor and to include GATA-3, ERs, PgRs and HER-2 to the immunohistochemical panel.

Artificial intelligence (AI) has found extensive applications in the sustainability domain. The municipal solid waste incineration (MSWI) process can achieve waste-to-energy (WTE) goals through the assistance of automation and information technologies. In theory, AI can facilitate the intelligent operation of the MSWI process, simultaneously achieving low pollution emissions and high production efficiency. This study provides an overview of AI applications in the MSWI process. Addressing fundamental challenges, the optimal control of the MSWI process is categorized into four aspects: modeling, control, optimization, and maintenance. Subsequently, this study conducts a detailed analysis and discussion of AI applications in each of these technological domains. In conclusion, this paper outlines the future research directions and provides an outlook on the fundamental issues pertaining to AI applications in the optimal control of the MSWI process.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

Accurate measurement of solid precipitation (S) has a critical importance for proper understanding of the Earth’s hydrological cycle, validation of emerging technologies and weather prediction models, and developing parameterizations of severe weather elements such as visibility (Vis). However, measuring S is still a challenging problem mainly because of wind effects. The wind effects are normally mitigated by using a Double-Fence Automated Reference (DFAR) system to reduce the wind speed (Ug). To contribute towards addressing some of these issues we have analyzed data sets collected at a site located in Southern Ontario, Canada using several instruments. The instruments include two Geonor gauges, one placed inside a DFAR (SDFAR) and the other inside a double Alter shield (DASG), a Pluvio2 gauge inside a single Alter shield (SASP), a HotPlate, a PARSIVEL2 Disdrometer that measures S and fall velocity (V), and a FD12P senor that measures S and type and Vis. The results show that for the Ug observed in this study (Ug &lt; 6 ms-1), both DASG and SASP have similar collection efficiency (CE) of near 70%. The transfer functions (TF) for DASG and SASP as a function of Ug and also Ug, and V have been derived. The TF for the DASG that includes both Ug and V showed better agreement with observation than just Ug alone. The S measured using all the other instruments were correlated well with SDFAR, but the PARSIVEL2 and FD12P overestimated and underestimated the snow amount respectively as compared the SDFAR. However, the HotPlate captured similar amount of S as the SDFAR. According to this study, the SDFAR showed good correlation with Vis.

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

The creation of mitochondria-targeted vector systems is a new tool for the treatment of socially significant diseases. Phosphonium groups provide targeted delivery of drugs through biological barriers to organelles. For this purpose, a new class of alkyl(diethylamino)(phenyl) phosphonium iodides (bromides) 1 containing one, two, or three diethylamino groups were obtained by the reaction of alkyl iodides (bromides) with (diethylamino)(phenyl)phosphines under mild conditions and high yields. The structure of compounds 1 was established by NMR and XRD. In vitro a high cytotoxicity against the lines M-Hela, HuTu 80, PC3, DU-145, PANC-1 and MCF-7 was found. Selectivity index are in the range of 0.06-4.0 M (SI 17-277) for the most active compounds. ROS production, mitochondrial localization and the process of cellular apoptosis were investigated. Decorated by 1 of lipid systems (liposomes and solid lipid nanoparticles) improve the cytotoxicity and a decrease in toxicity against normal cell lines. Compounds 1 induce apoptosis proceeding along the mitochondrial pathway. Aminophosphonium salts 1 also exhibit a high selective activity against the Gram-positive bacteria strains S. aureus 209P, B. segeus 8035, including methicillin-resistant strains of S. aureus (MRSA-1, MRSA-2), comparable to the activity of the fluoroquinolone antibiotic norfloxacin. A moderate in vivo toxicity in CD-1 mice was established for the lead compounds.

A field experiment was conducted on the farm of Abi Jarash in Agricultural Collage, different rates of olive solid waste and cow manure were used, as follows: (control, fresh olive solid waste 100%, fresh olive solid waste 75%+ cow manure 25%, fresh olive solid waste 50%+ cow manure 50%, fresh olive solid waste 25+ cow manure 75%, Fermented Olive Solid Waste 100%, Fermented olive solid waste 75%+ cow manure 25%, Fermented olive solid waste 50%+ cow manure 50%, Fermented olive solid waste 25+ cow manure 75%), wheat was seeded. The impact of fresh and fermented olive solid waste and cow manure on some chemical and fertility soil properties was studied. the olive solid waste treatment 100% which added had more effect on the organic matter, exchange capacity, nitrogen, phosphorus and potassium in soil, plant and productivity, after that the fermented olive solid waste 75% + cow manure, fresh olive solid waste 100% comparing with the control, the values of organic matter were (25% 2.73, 2.39) and the cation exchange capacity (21.76, 20.44, 19.38) and for phosphorus (303.3, 277.8, 171.8) mg / kg, while the values of potassium ​​were (303.3, 277.8, 171.8) mg / kg. In terms of plant content, the plant content of nitrogen, phosphorus and potassium were the same as for grains (2.784, 2.606, 2.126), (0.4535, 0.4226, 0.2753), (1.876, 1.762, 1.234) respectively, (0.2875, 0.2016) respectively for the same previous treatments and elements. olive solid waste 100% was the highest productivity comparing with the other treatments, where the productivity of wheat was (9.513) ton. ha-1.

From their discovery in 2002, BRAF mutations have been identified as clear drivers of oncogenesis in several cancer types. Currently, their incidence rate is nearly 7% of all solid tumors with BRAF V600E constituting approximately 90% of these diagnoses [1]. In melanoma, thyroid cancer, and histiocytic neoplasms, BRAF hotspot mutations are found at a rate of about 50%, while in lung and colorectal cancers they range from 3 to 10% of reported cases [2-5]. Though present in other malignancies such as breast and ovarian cancers, they constitute a small portion of diagnoses (<1%). Given their frequency along with advancements in screening technologies, various methods are used for the detection of BRAF-mutant cancers. Among these are targeted next-generation sequencing (NGS) on tumor tissue or circulating tumor DNA (ctDNA) and immunohistochemistry (IHC)-based assays. With advancements in detection technologies, several approaches have been taken for the treatment of BRAF mutant cancers. In this review we retrace the milestones that led to the clinical development of targeted therapies currently available for these tumors.

We observed and studied the phenomenon of the redox front propagation in different polyaniline (PAni) deposited samples interfaced with liquid or solid polymeric electrolyte. The front of electrochemical conversion, in which the insulator and the conductor parts of PAni are interfaced, is studied observing the temporal evolution of the conductivity of PAni samples. The propagation of redox front was studied in electrochemically obtained thick (2 µm) and in thin (50 nm) poly-aniline films, obtained using Langmuir-Blodgett (LB) method. In the configuration that we tested, the speed of the red-ox front propagation for the thin LB films was found to be 200 micron/sec opening the way for the manufacturing large neural networks, realized using PAni based memristive devices, in which the memristance can be quickly changed in the programmable manner. The prototypes of the spiking neuron connections were manufactured on the basis of lithographically developed gold contacts, bridged by electrochemically grown polyaniline and placed under polymer electrolyte layer with only one counter electrode (gate) for the whole manifold of pseudo-two-terminal memristor bridges. The spike propagation was studied in such gold-polyaniline systems. The research opens the possibility of miniature spike or rate-based neural network circuits manufacture, based on metal pads and polyaniline.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

The present study aimed to evaluate the effect of the citric acid on the properties of solid pine wood, which were submitted to thermomechanical treatment. A preliminary test was performed in a previous study to evaluate the influence of different temperatures of pressing and concentrations of citric acid over the physical properties of wood. After choosing the best treatments (170°C and 5% and 10% of citric acid) it was evaluated the effect of these on the chemical properties (SEM, FTIR and pH), on the density profile using an X-ray microtomography, and on the resistance to ageing through abrasion test. The result of the chemical analysis allowed to observe an increase of the presence of ester functional groups, as well as a better coverage and higher acidity of the surface. The density profile technique allowed to observe the formation of peaks of density on the surface where the acid was applied. Lastly, it was also possible to verify an increase in the resistance to abrasion because of the application of the citric acid.

Nano-drugs and nano-delivery systems are rapidly evolving, with new strategies emerging in the current practices. The evolution of these technologies began with modifying the chemical structure, progressing to supramolecular ionic complexes, and culminating in elegant ad hoc delivery systems. Nanoparticles have numerous benefits as a carrier system for delivering therapeutic agents to intra-arterial sites. These benefits include their subcellular size, targeted surfaces, good suspensibility, and uniform dispersity, making them an ideal choice for catheter-based delivery. Despite the advancements made in the field of nano-drugs and nano-delivery systems, there are still some hurdles to overcome in terms of their commercial availability.The current review presents an updated summary of recent advancements in nano-drugs and nano-delivery systems, including their commercial availability. We aim to discuss the present challenges and prospects of commercially available nano-drugs and nano-delivery systems. Here, we provide a precise and informative overview of the current state of these technologies and underscore the potential they hold for future developments. Further, we have categorized commercially available modifications, name, parent company and their main applications in nano-drugs.

The results of measuring the capacity of a thin-film solid-state lithium-ion battery (SSLIB) Ti|Si@O@Al|LiPON|LiCoO₂|Ti at different charge currents are reported. It is shown that the dependence of the capacity on the current density follows the Peukert's law, which is characterized by a low value of the Peukert’s exponent in the region of low currents and a high value of the exponent in the region of high currents. A capacity model for a SSLIB based on the balance of diffusion and migration currents is proposed and the dependence of the capacity on the charge current is derived. The obtained dependence is well approximated by Peukert's law with an exponent of 1.39, which is intermediate between the exponents for lithium-ion batteries with liquid electrolyte and SSLIBs.