In the present paper, Co-B/SiC composite coatings were obtained via electrodeposition from colloidal suspensions with different concentrations of SiC particles and subsequent heat treatments at 350 °C. The composition, morphology and structure of the Co-B/SiC composite coatings were analyzed using glow discharge spectrometry (GDS), scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) and X-ray diffraction (XRD). Hardness and tribological properties were also studied. The results showed that an increase in the SiC concentration in the colloidal suspensions resulted in both an increase in the SiC content and a decrease in the B content in the obtained Co-B/SiC coatings. The Co-B/SiC coatings were adherent, glossy and soft and exhibited a homogeneous composition in all thicknesses. By contrast, an increase in the SiC particle content of the Co-B/SiC composite coating from 0 to 2.56 at.% SiC reduced the hardness of the film from 680 to 360 HV and decreased the wear volume values from 1180 to 23 mm³ N^-1 m^-1, respectively (that is, the wear resistance increased). Moreover, when the Co-B/SiC coatings with SiC content ranging from 0 to 2.56 at.% SiC were subjected to a heat treatment process, the obtained coating hardness values were in the range of 1200 to 1500 HV and the wear volume values were in the range of 382 to 19 mm³ N^-1 m^-1.

The manufacture of SiC-based composites is quite widespread, and currently different methods are employed for to produce them. The most efficient method, taking into account the cost/performance ratio, is reactive melt infiltration. It consists in infiltrating liquid silicon into a porous preform that must contain carbon, so that SiC is produced during infiltration. This chemical reaction is, in fact, the driving force of the process. In the present work, the synthesis of two SiC-based composite materials with very different applications and microstructures has been studied and optimized. In both cases, materials have been obtained with suitable properties for the selected applications. One of the materials studied is SiCp/Si for protection systems such as armor jackets, and the other one is Cf/SiC for use in braking systems. For the optimization, the dwell time and the atmosphere (Ar or primary vacuum) were used as variables. It has been found that in both preforms the optimum conditions are 1 hour dwell time and a vacuum atmosphere at 1450 °C. The effect of these parameters on microstructure and infiltration kinetics are discussed.

Several challenges stand in the way of production of Metal Matrix Composites (MMCs) such as higher processing temperatures, particulate mixing, particulate-matrix interface bonding issues and ability to process into desired geometrical shapes. Although there are many literatures showing composites with single particulate reinforcements, the studies on composites with multiple reinforcing agents (hybrid composites) are found to be limited. Development of a hybrid particulate composite with optimized mechanical and tribological properties is very significant to suit modern engineering applications. In this study, Al-Si hypereutectic alloy (A390) is used as the matrix and Silicon Carbide (SiC) and Graphite (Gr) and Molybdenum di-Sulphide (MoS₂) are used as particulates. Particulate volume (wt%) is varied and sample test castings are made using squeeze casting process through stir casting processing route. The evaluation of mechanical properties indicates that presence of both the hard phase (SiC) and the soft phase has distinct effect on the properties of Hybrid Composite. Composite samples were characterized to understand the performance and to meet the tribological applications. Fractography study indicated an intra-granular brittle fracture for hybrid composites. Wear study shows that Hybrid MMCs has better tribological performance compared to that of A390 alloy.

At Mae-Moh power plant, Thailand, superheater tubes, which are exposed in fly ash environ-ment, often degrade due to solid particle erosion. To extend the service lifetime of the superheater tubes, the high velocity oxy-fuel (HVOF) thermal spray technique is used to deposit a protective coating on the material, SA213-T22 steel. In this work, the solid particle erosion of the Co-28Cr and WC-12Co coatings was investigated using erodent particle impingement at the angles of 30o and 90o with an average particle size of 60 μm. The erosion behavior of SA213-T22 with and without Co-28Cr and WC-12Co coatings was explained using ductile and brittle erosion modes. The erosion test resulted in the brittle mode for both Co-28Cr and WC-12Co coatings, while SA213-T22 without coating indicated the ductile mode. On the investigation of surface morphology, the Co-28Cr coating showed mostly microcracks in contrast with the WC-12Co coating, fracture, de-bonding and deep cavities were also observed. Erosion resistance of the Co-28Cr coating was significantly higher than the WC-12Co coating, due to high hardness, low porosity and high density of the coating.

SiC ceramics are excellent materials applied at high temperatures because of their light weight, excellent high temperature strength, and high thermal shock resistance. For better engineering properties, we made SiC with fractal lattices. Stress-strain behavior and modulus changes from room temperature to 1,250oC were analyzed using LAMMPS S/W, a molecular dynamics program. As a result of this study, it was confirmed that the modulus of elasticity of SiC crystals changed in the range of about 475 GPa to 425 GPa as it increased from room temperature to 1,250 oC, The stress-displacement characteristics of SiC crystals, which could not be measured at a high temperature of 1,000 oC or higher, could be ensured.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

In this review paper, an overview of radiation induced deep level defects in n-type 4H-SiC studied by junction spectroscopy techniques, is given. In addition to carbon vacancy (Vc), present in as-grown material already, we focus on the following deep level defects: silicon vacancy (VSi), carbon interstitial (Ci), and carbon antisite-carbon vacancy (Csi-Vc) pair. Recent advances in measurements by junction spectroscopy techniques that have led the progress toward better understanding of radiation induced defects are presented.

We report on metastable defects introduced in n-type 4H-SiC material by epithermal and fast neutron irradiation. The epithermal and fast neutron irradiation defects in 4H-SiC are much less explored compared to electron or proton irradiation induced defects. In addition to silicon vacancy (Vsi) and carbon antisite-carbon vacancy (CAV) complex, the neutron irradiation has introduced four deep level defects, all arising from the metastable defect, the M-center. The metastable deep level defects were investigated by deep level transient spectroscopy (DLTS), high-resolution Laplace DLTS (L-DLTS) and isothermal DLTS. The existence of the fourth deep level M4, recently observed in ion implanted 4H-SiC, has been additionally confirmed in neutron irradiated samples. The isothermal DLTS technique has been proven as a useful tool for studying the metastable defects.

SiC is a material with excellent mechanical and thermal properties, but with a high production cost. Obtaining SiC by reactive infiltration is an attractive method and at a much lower cost than the traditional sintering process. However, the reactive infiltration process presents a serious problem, which is the high residual silicon content, which decreases its range of application. The replacement of silicon with silicides is a widely used alternative. The present investigation shows the good mechanical properties of the SiC/IrSi₃ composite material obtained by reactive infiltration of SiC/C preforms with Ir-Si alloys. The thermomechanical analysis shows a high compatibility of silicide with SiC. The presence of the silicide shows a substantial improvement against the oxidation of the SiC/Si composites.

This study aimed to assess the ecotoxicological effects of the interaction of fullerene (C₆₀) and benzo[a]pyrene (B[a]P) on the marine mussel, Mytilus galloprovincialis. The uptake of nC₆₀, B[a]P and mixtures of nC₆₀ and B[a]P into tissues was confirmed by GC-MS, LC-HRMS and ICP-MS. Biomarkers of DNA damage as well as proteomics analysis were applied to unravel the toxic effect of B[a]P and C₆₀. Antagonistic responses were observed at the genotoxic and proteomic level. Differentially expressed proteins (DEPs) were only identified in the B[a]P single exposure and the B[a]P mixture exposure groups containing 1 mg/L of C₆₀, the majority of which were down-regulated (~52%). No DEPs were identified at any of the concentrations of nC₆₀ (p < 0.05, 1% FDR). Using DEPs identified at a threshold of (p < 0.05; B[a]P and B[a]P mixture with nC₆₀), gene ontology (GO) and Kyoto encyclopedia of genes and genomes (KEGG) pathway analysis indicated that these proteins were enriched with a broad spectrum of biological processes and pathways, including those broadly associated with protein processing, cellular processes and environmental information processing. Among those significantly enriched pathways, the ribosome was consistently the top enriched term irrespective of treatment or concentration and plays an important role as the site of biological protein synthesis and translation. Our results demonstrate the complex multi-modal response to environmental stressors in M. galloprovincialis.

Mutations within the hepatitis B virus (HBV) genome have been associated with rapid progres-sion to hepatocellular carcinoma (HCC); however, there is limited information regarding the prevalence and impact of these mutations in most of sub-Saharan Africa, including Botswana. We aimed to determine the prevalence of HBV mutations known to be associated with progression to HCC using a retrospective, cross-sectional analysis of 48 previously generated HBV sequences from adults with concomitant HBV/HIV initiating HIV antiretroviral therapy in Botswana. The sequences were aligned with reference sequences, and HCC-associated mutations were manually identified using BioEdit. Sixteen (33.3 %) of 48 participant samples had 20 HCC-associated mu-tations. Seven HCC mutations were present in the core region, 4 in the preCore region, 7 in the X region, and one mutation in the surface region, as well as deletions within the preSurface 1 region. Seven of the 16 participants (43.8%) had multiple HCC-associated mutations. There were also previously uncharacterized mutations at positions with known HCC-associated mutations. HCC-associated mutations were common in this cohort; hence, some participants may require close clinical monitoring as they might be more prone to rapid disease progression. Other functionally uncharacterized polymorphisms were also detected and require characterization in future studies.

Background: Single nucleotide polymorphisms (SNPs) in the SLC10A1 gene, coding for a functional receptor of hepatitis B virus (HBV), sodium taurocholate co-transporting polypeptide (NTCP), may influence the susceptibility, the outcome, and disease course of HBV infection in some populations. Aim: to determine the prevalence of SNPs of NTCP gene, rs2296651 and rs943277, and their relationship with chronic HBV infection in a group of Egyptian patients. Methods: 137 patients with HBV and 65 healthy controls were enrolled, and the patients were divided into two groups; group I chronic HBV infection (68 patients with normal ALT and minimal or no liver necroinflammation or fibrosis) and group II chronic hepatitis B (69 patients with elevated ALT and moderate or severe liver necroinflammation). They were subjected to full history taking, clinical examination, laboratory investigations, abdominal ultrasound, and liver stiffness measurement using both Echosens® Fibroscan and acoustic radiation force impulse (ARFI). Real time PCR TaqMan 5’ allelic discrimination assay was applied to detect the SNPs in NTCP gene, rs2296651 and rs943277. Results: On studying the rs2296651 variant, all controls and patients had genotype GG without any significant association with HBV infection or disease progression. However, the rs943277 variant in all controls and 98% of patients had genotype GA, except for two chronic HBV infection patients who had genotype AA, but no significant difference between patients and controls was found. The non-invasive methods for liver fibrosis assessment ARFI, AST/platelet's ratio (APRI), and fibrosis-4 score (FIB-4) could predict the stages of fibrosis in agreement with Fibroscan with AUCOR 0.8, 0.79, and 0.76, respectively. Conclusion: These findings may suggest that there is no relation between these SNPs of the NTCP gene and susceptibility or chronicity of HBV infection in the Egyptian population. We also suggest that the use of the non-invasive methods for liver fibrosis assessment, ARFI, FIB-4, and APRI may decrease the need for liver biopsies in prediction of significant hepatic fibrosis in chronic HBV patients.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

In this review, we provide an overview of the most common majority and minority charge carrier traps in n-type 4H-SiC material. We focus on the results obtained by different applications of junction spectroscopy techniques. The basic principles behind the most common junction spectroscopy techniques are given. These techniques, namely, deep level transient spectroscopy (DLTS), Laplace DLTS (L-DLTS) and minority carrier transient spectroscopy (MCTS) have led to recent progress in identifying and better understanding of the charge carrier traps in n-type 4H-SiC material.

In this review paper, an overview of the application of n-type 4H-SiC Schottky barrier diodes (SBDs) as radiation detectors is given. We have chosen 4H-SiC SBDs among other semiconductor devices such as PiN diodes or metal-oxide-semiconductor (MOS) structures, as significant progress has been achieved in radiation detection applications of SBDs in the last decade. Here, we present the recent advances at all key stages in the application of 4H-SiC SBDs as radiation detectors, namely: SBDs fabrication, electrical characterization of SBDs, and their radiation response. Main achievements are highlighted, and main challenges are discussed.

Polymer-derived SiC-polycrystalline fiber (Tyranno SA) shows excellent heat-resistance up to 2000^oC, and relatively high strength. Up to now, through our research, the relationship between the strength and residual defects of the fiber, which were formed during the production processes (degradation and sintering), has been clarified. In this paper, we addressed the relationship between the production condition and the surface roughness of the obtained SiC-polycrystalline fiber, using three different raw fibers (Elementary ratio: Si₁Al_0.01C_1.5O_0.4~0.5) and three different types of reactor (Open system, Partially-open system, and Closed system). With increase in the oxygen content in the raw fiber, the degradation during the production process easily proceeded. In this case, the degradation reactions (SiO+2C=SiC+CO and SiO₂+3C=SiC+2CO) in the inside of each filament become faster, and then the CO partial pressure on the surface of each filament is considered to be increased. In consequence, according to Le Chatelier’s principle, the surface degradation reaction and grain growth of formed SiC crystals would be considered to become slower. That is to say, using the raw fiber with higher oxygen content and closed system (highest CO content in the reactor), much smoother surface of the SiC-polycrystalline fiber could be achieved.

The lattice reduction aided(LRA) algorithm has attracted widely attention of researchers in MIMO systems because of its low complexity to achieve full diversity. However, most lattice reduction auxiliary algorithms do not directly improve system performance. In this paper, a modified lattice reduction successive interference cancellation (SIC) algorithm is proposed for MIMO OFDM system mild changing the complexity of LRA algorithm. At present, the MMSE SQRD algorithm has the problem of regarding too much useful signals as the residual interference which cannot be cancelled by successive interference cancellation. Since the diagonal elements of useful signals are non-zero, the components of the symbols to be detected still present in the interference term, treating all the signals as interference will be resulted in performance loss. To solve this problem, the modified matrix is proposed.by moving this symbol component into the signal term, the proposed algorithm can provide the better performance than MMSE SQRD algorithm. The analysis shows that the LRA-MMSE-SIC algorithm of proposed in this paper significantly improves the system performance with mild increasing the complexity. The simulation results show that the performance of the proposed algorithm is improved by 1dB and 8dB compared with the comparison algorithm when the bit error rate is 10−3.

A heterograft copolymer with an alginate backbone, hetero-grafted by polymer pendant chains displaying different Lower Critical Solution Temperatures (LCSTs), combined with a pH-responsive Poly(2-vinyl pyridine)-b-poly(ethylene oxide) (P2VP-b-PEO) diblock copolymer forming micellar nanoparticles, was investigated in aqueous media at various pH. Due to its thermoresponsive side chains, the copolymer forms hydrogels with thermo–induced sol–gel transition, above a critical temperature, Tgel (thermo–thickening). However, by lowering pH of the medium in acidic regime, a remarkable increase of the elasticity of the formulation was observed. This effect was more pronounced in low temperatures (below Tgel) suggesting secondary physical crosslinking, which induces significant changes in the hydrogel thermoresponsiveness, transforming the sol–gel transition to soft gel–strong gel. Moreover, the onset of thermothickening shifted to lower temperatures followed by broadening of the transition zone, implying intermolecular interactions between the uncharged alginate backbone with the PNIPAM side chains, likely through H–bonding. The shear–thinning behavior of the soft gel in low temperatures provides injectability, which allows 3D–printing potential applications. Furthermore, the heterograft copolymer/nanoparticles composite hydrogel, encapsulating a model hydrophobic drug in the hydrophobic cores of the nanoparticles, was evaluated as pH-responsive drug delivery system. The presented tunable drug delivery system might be useful for biomedical potential applications.

The communication link between the base station and the mobile sensor networks, such as multi-agent systems for collaborative tasks which include ground mobile robots and drones, is crucial for localization and success of tasks in indoor environments. The Power-domain Non-Orthogonal Multiple Access (P-NOMA) is an emerging multiplexing technique that enables the base station to accumulate signals for different agents using the same time-frequency channel. The environment information such as distance from the base station is required at the base station to calculate communication channel gains and allocate suitable signal power to each agent. The accurate estimate of the position for power allocation of P-NOMA in a dynamic environment is challenging due to changing location of the end-agent and shadowing. In this paper, we take advantage of the two-way Visible Light Communication (VLC) link to: (1) estimate the position of the end-agent in a real-time indoor environment based on the signal power received at the base station and (2) allocate resources using the Simplified Gain Ratio Power Allocation (S-GRPA) scheme with the look-up table method. In addition, we use the Euclidean Distance Matrix (EDM) to estimate the location of the end-agent whose signal was lost due to shadowing.

conclusions. The blends of ultrahigh molecular weight polyethylene/polypropylene (UHMWPE/PP) possess excellent processability, but limited by its reduced mechnical properties. Herein, the high mechanical properties and wear—resistance UHMWPE/PP composites were fabricated by the addition of silicon carbide (SiC) nanoparticles under a consecutive elongational flow without any other additives or solvents. The morphology and thermal properties, mechanical properties, wear resistance as well as scratch resistance of UHMWPE/PP/SiC composites were investigated . The mechanical properties and friction resistance of composites increase initially then decrease with the increase content of SiC. The optimum mechanical properties of UHMWPE/PP/SiC composites are achieved when the content of SiC is 3 phr. In addition, both the hardness and scratch resistance of composites improved upon increasing the content of SiC. These improved mechanical properties and wear resistance originate from the well disperison of SiC nanoparticles along with favourable interfacial adhesive under a consecutive elongational flow.

The interfacial mechanics and electrical properties of the SiC reinforced copper matrix composites were studied via the first principles method. The work of adhesion (Wad) and the interfacial energies were calculated to evaluate the stabilities of the SiC/Cu interfacial models. The carbon terminated (CT)-SiC/Cu interfaces were predicted more stable than those of the silicon terminated (ST)-SiC/Cu from the results of the Wad and interfacial energies. The interfacial electron properties of SiC/Cu were studied via the charge density distribution, charge density difference, electron localized functions and partial density of the state. The covalent C-Cu bonds were formed based on the results of the electron properties, which further explained the fact that the interfaces of the CT-SiC/Cu are stable than those of the ST-SiC/Cu. The interfacial mechanics of the SiC/Cu were investigated via the interfacial fracture toughness and ultimate tensile stress, and the results indicate that both CT- and ST-SiC/Cu interfaces are hard to fracture. The ultimate tensile stress of the CT-SiC/Cu is nearly 23GPa, which is smaller than those of the ST-SiC/Cu of 25 GPa. The strains corresponding to their ultimate tensile stresses of the CT- and ST-SiC/Cu are about 0.28 and 0.26, respectively. The higher strains of CT-SiC/Cu indicate their stronger plastic properties on the interfaces of the composites.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

The design of processing routes involving the presence of the liquid phase is mainly associated with the knowledge of its surface and transport properties. Despite this need, due to experimental difficulties related to high temperature measurements of metallic melts, for many alloy systems neither thermodynamic nor thermophysical properties data are available. A good example lacking these datasets represents the Ir-Si system, although over the last fifty years, the structures and properties of its solid phases have been widely investigated. To compensate the missing data, the Gibbs free energy of mixing of the Ir-Si liquid phase was calculated combining the model predicted values for the enthalpy and entropy of mixing using Miedema’s model and Free Volume Theory, respectively. Subsequently, in the framework of statistical mechanics and thermodynamics, the surface properties were calculated using the Quasi Chemical Approximation (QCA) for the regular solution, while to obtain the viscosity, the Moelwyn-Hughes (MH) and Terzieff models were applied. Subsequently, the predicted values of the abovementioned thermophysical properties were used to model the non-reactive infiltration isotherm of Ir-Si (eutectic) / SiC system.

The paper presents the design stages of a single-phase Silicon Carbide bidirectional DC-AC converter. This includes the LCL filter design responsible to meet grid connection requirements. A 3kW laboratory prototype of the power converter is built employing a low-cost phase locked loop and its results are presented. The design of the low-cost phase locked loop and its implementation are depicted in some detail.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

The framework proposed by Alison Druin about 20 years ago, which defined the roles children play in technology design, has been widely adopted by the Child-Computer Interaction (CCI) community. While some studies have adopted relevant roles as presented in the framework, others have argued for extending the framework to include newly identified roles. Still, other studies argue that Druin's framework failed to account for roles children may take up as they interact with peers or with tools. Consequently, this systematic literature review examines children’s emerging and changing roles in the codesign of new technologies. Specifically, we answered the research question: What new roles emerge in research as children co-design new technologies? Our effort aims at providing evidence of new roles children have adopted in literature, which may help researchers in the CCI community make more informed decisions about participatory design approaches with children.

Ocean big data is the scientific practice of using big data technology in the marine field. Data from satellites, manned spacecraft, space stations, airship, unmanned aerial vehicles, shore-based radar and observation stations, exploration platforms, buoys, underwater gliders, submersibles, and submarine observation networks are seamlessly combined into the ocean’s big data. Increasing numbers of scholars have tried to fully analyze the ocean’s big data. To explore the key research technology knowledge graphs related to ocean big data, articles between 1990 and 2020 were collected from the “Web of Science”. By comparing bibliometric software and using the visualization software Cite-Space, the pivotal literature related to ocean big data, as well as countries, institutions, categories, and keywords, were visualized and recognized. Journal co-citation analysis networks can help determine the national distribution of core journals. Co-citation analysis networks for documents show authors who are influential at key technical levels. Key co-occurrence analysis network keywords can determine research hot spots and research frontiers. The three supporting elements of marine big data research are shown in the co-citation network. These elements are author, institution, and country. By examining the co-occurrence of keywords, the key technology research directions for future marine big data were determined.

Integrating sustainable processes and innovative waste utilization not only addresses environ-mental challenges but also aligns with evaluating energy sustainability and creating the circular waste management. This study presents a comparative analysis of liquid fuel production from waste tires and water hyacinth using two thermochemical methods: co-pyrolysis (direct method) and co-gasification integrated with the Fischer-Tropsch (FT) process (indirect method). The As-pen Plus simulation software version 9 is employed to develop models, determining optimal operating conditions for maximum liquid fuel, and assessing economic viability. Co-pyrolysis simulations reveal an increase in oil products and a decrease in gas products with higher blending weight ratios of waste tires/water hyacinth (W/B) and lower pyrolyser temperatures. Operating at 400°C with a blending weight ratio of 75:25 provided the maximum liquid fuel rate of 6649.22 gal/day. For co-gasification, optimal conditions (W/B = 50:50, T = 800°C, steam to feed ratio (S/F) = 1) result in the highest syngas yield of 115.92 kmol/h. Fischer-Tropsch simulations demonstrate an increase in gasoline and a decrease in diesel with rising reactor temperatures. At 230°C, the maximum liquid fuel rate reaches 8817.15 gal/day. The economic and production yield analysis indicates that the indirect method better than the direct method, providing higher liquid fuel yields and investment worthiness.

The severe respiratory distress syndrome (SRDS) has been a significant clinical issue in modern respiratory medicine. Its role in COVID-19 pandemic is not well defined. Outside-the-hospital SRDS is usually community-acquired septic pneumonia; however, in-hospitals incidences are complicated by co-infections. While SRDS is genetically selected in European and African origins, these are not clear in Middle East, particularly in COVID-19 backgrounds. There is a severe paucity in high quality data on correlations between COVID-19, ARDS, co-infectome, and patient demographics. We have conducted a comprehensive investigation on 298 patients for associations of SRDS, coinfections, and patient demographics on COVID-19 patients’ outcomes. Of these, 9.4% (n=28) had SRDS, and the rest (90.6%) had not. 54% of those with SRDS died while 84% survived; SRDS fatality was highly significant (Chi-square test P-value = 0.00000246). Irrespective of gender, the age of patients was significantly associated with SRDS (72.9 +/-8.9) compared to those without it (56.2 +/-15.1). However, there was no significant difference neither in the age of admitted patients before COVID-19 (58.5 +/-15.3) and during COVID-19 (57.2 +/-15.5) nor in the gender and COVID-19 fatality (Fisher Exact test 2-sided 1.000, 1-sided .546) ruling out that SRDS age-specificity were selected by virus susceptibility. A 100% of SRDS patients without bacterial co-infections survived while only 25% of those with co- infectome did not; this association was highly significant (P value= 0.00041). Co-infections alone without underlying SRDS was also associated with high fatality among patients (P value= 0.00000000076). Almost all COVID-19 patients without co-infectome (99.2%) survived while 28% of those with bacterial co-infection died. The major bacterial pathogens that potentially predisposed to SRDS, were Acinetobacter baumannii, and Escherichia coli either alone or in a mixed infection with Klebsiella pneumoniae were predominant species identified during SRDS attack. Thus, Gram-negative co-infectome potentially induced fatal SRDS aggravating COVID-19 outcome. These findings have significant clinical implications in specific differential diagnosis of SRDS syndromes for subsequent empiric therapy and patient management strategies. Future vertical investigation for similar mechanisms of cytokine-induced SRDS by Gram negative pathogens is imperative since hypervirulent strains are rapidly circulating in the region. The study is limited by a single center study confined to Ha’il hospitals; large scale investigation in major national hospitals would gain more insights.

Leishmania parasites present astonishing adaptative abilities that represent a matter of life or death within disparate environments during the heteroxenous parasite life cycle. From an evolutionary perspective, organisms develop methods of overcoming such challenges. Strategies that extend beyond the genetic diversity have been discussed and include variability between parasite cells during the infections of their hosts. The occurrence of Leishmania subpopulation fluctuations with variable structural genomic contents demonstrates that a single strain might shelter the variability required to overcome inconsistent environments. Such intrastrain variability provides parasites with an extraordinary ability to adapt and thus survive and propagate. However, different perspectives on this evolution have been proposed. Strains or species living in the same environment can cooperate but also compete. These interactions might increase the replication rate of some parasites but cause the loss of more aggressive competitors for others. Adaptive responses to intra- and interspecific competition can evolve as a fixed strategy (replication is adapted to the average genetic complexity of infections) or an optional strategy (replication varies according to the genetic complexity of the current infection). This review highlights the complexity of interspecies and intrastrain interactions among Leishmania parasites as well as the different factors that influence this interplay.

In this paper, the single event burnout(SEB) and reinforcement structure of 1200V SiC MOSFET (SG-SBD-MOSFET) with split gate and schottky barrier diode(SBD) embedded were studied. The device structure was established using Sentaurus TCAD, and the transient current changes of single event effect(SEE), SEB threshold voltage, as well as the regularity of electricfield peak distribution transfer were studied when heavy ions were incident from different regions of the device. Based on SEE analysis of new structural device, two reinforcement structure designs for SEB resistance were studied, namely the expansion of P+body contact area and the design of multi-layer N-type interval buffer layer. Firstly, two reinforcement schemes for SEB were analyzed separately, and then comprehensive design and analysis were carried out. The results showed that the SEB threshold voltage of heavy ions incident from the N+source region was increased by 16% when using the P+body contact area extension alone; When the device is reinforced with multi-layer N-type interval buffer layer alone, the SEB threshold voltage increases by 29%; The comprehensive use of P+body contact area expansion and multi-layer N-type interval buffer layer reinforcement increased the SEB threshold voltage by 33%. Overall, the breakdown voltage of the reinforced device decreased from 1632.935V to 1403.135V, which can be seen as reducing the remaining redundant voltage to 19%. The device performance was not significantly affected.

Understanding the stability limit of crystalline materials under variable tensile stress conditions is of capital interest for their technological applications. In this study, we present results from first-principles density functional theory calculations that quantitatively account for the response of selected covalent and layered materials to general stress conditions. In particular, we have evaluated the ideal strength along the main crystallographic directions of 3C and 2H polytypes of SiC, hexagonal ABA stacking of graphite and 2H-MoS2. Transverse superimposed stress on the tensile stress was taken into account in order to evaluate how the critical strength is affected by these multi-load conditions. In general, increasing transverse stress from negative to positive values leads to the expected decreasing of the critical strength. Few exceptions found in the compressive stress region correlate with the trends in the density of bonds along the directions with the unexpected behavior. In addition, we propose a modified spinodal equation of state able to accurately describe the calculated stress-strain curves. This analytical function is of general use and can also be applied to experimental data anticipating critical strengths and strains values and providing informattion on the energy stored in tensile stress processes.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

We present atomic structures and nonequilbrium synthesis of new class of materials, where the basic structural unit is a diamond tetrahedron. When units of one, two, and three tetrahedra are randomly packed, we create distinct phases of amorphous Q-carbon. Four tetrahedra in two adjacent layers lead to crystalline diamond lattice, which has four missing tetrahedra alternately. When these four missing tetrahedra are filled, we create subunit cell of crystalline Q-diamond. Theoretical calculations show that superconducting transition temperature (Tc) in 50 atomic % B-doped Q-diamond can reach near room temperature at ambient pressures. This is consistent with our earlier results using low-loss EELS measurements in 50 atomic % B-doped Q-carbon, which had mostly amorphous QB3 phase mixed with some crystalline Q-diamond phase. These EELS results showed that the Tc for these samples was in between 90K and 300K. Theoretical calculations of density of states, Eliashberg function, electron-phonon interaction parameter, and root-mean-square and logarithmic average of frequency in crystalline Q-diamond show Tc in the range of 268K to 300K, which is in a complete agreement with our EELS results in QB3.

BACKGROUND: Chronic hepatitis B infected with Hepatitis B virus remains a major health concern worldwide. Despite standard interferon-α and nucleotide analogues have been shown to reduce the deterioration of liver disease among chronic hepatitis B patients, covalently closed circular DNA was still difficult to eradicate. METHODS: A literature search of Pubmed and Web of science was performed with the following key words: ‘CRISPR’, ‘CRISPR/Cas9’, ‘hepatitis B’, ‘HBV’, ‘chronic hepatitis B’ and ‘HBV cccDNA’. The information about CRISPR/Cas9 for the treatment of HBV cccDNA or hepatitis B was reviewed. RESULTS: CRISPR/Cas9 could treat hepatitis B through suppressing or clearing HBV cccDNA with different gRNAs. CONCLUSION: With the emergence of CRISPR/Cas9 (the RNA-guided clustered regulatory interspaced short palindromic repeats, CRISPR) editing technology, clearance of hepatitis B virus and better prevention of liver carcinoma seemed to be possible.

Due to the difficult metallurgical conditions during production, advanced processing techniques are required to produce functionally graded metal matrix composites. In this study, we explored a novel approach by using a combination of two different methods to produce Functionally Graded 7075 Al / SiCp composites. First process was direct semi-solid stirring that was used to prevent particle agglomeration, brittle reaction products, floating or settling of the reinforcements and poor wettability for the production of SiCp (wt. 5-20%) reinforced aluminum matrix composites. In the direct semi-solid mixing process, the matrix material remains in a semi-solid state until the reinforcement addition process is completed. The second novel process was sequential squeeze casting to provide liquid diffusion between two composite layers that were used to produce functionally graded aluminum matrix composite. The microstructure and interlayer zones were characterized by using optical microscopy and scanning electron microscopy. The resulting functionally graded material was subjected to spectrometer analyses, density measurements, and metallographic examinations in order to determine the characteristics of its layers and interfacial zones, as well as to assess the formation of the graded structure. The results obtained from this research provide the potential to use this new combined manufacturing method, which is relatively inexpensive, efficient and easily applicable, in order to produce functionally graded SiCp reinforced aluminum composites.

New setting is introduced to study types of coloring numbers, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic hypergraphs. Different types of procedures including neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs are proposed in this way, some results are obtained. General classes of neutrosophic hypergraphs are used to obtain chromatic number, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic hypergraphs. Using colors to assign to the vertices of neutrosophic hypergraphs and characterizing representatives of the colors are applied in neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs. Some questions and problems are posed concerning ways to do further studies on this topic. Using different ways of study on neutrosophic hypergraphs to get new results about number, degree and co-degree in the way that some number, degree and co-degree get understandable perspective. Neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs are studied to investigate about the notions, coloring, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs. In this way, sets of representatives of colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges have key points to get new results but in some cases, there are usages of sets and numbers instead of optimal ones. Simultaneously, notions chromatic number, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges are applied into neutrosophic hypergraphs, especially, neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs to get sensible results about their structures. Basic familiarities with neutrosophic hypergraphs theory and hypergraph theory are proposed for this article.

The main objective of this paper is to identify the major research areas of ChatGPT through term and keyword co-occurrence network mapping techniques. For conducting the present study, total of 577 publications were retrieved from the Lens database for the network visualization. The findings of the study showed that “chatgpt” occurrence in maximum number of times followed by its related terms such as artificial intelligence, large language model, gpt, study etc. This study will be helpful to library and information science as well as computer or information technology professionals.

The normative and safeguarding role of ethics and law in the development of biomedical science and technology, as well as their importance in promoting the progress of the industry, analyzed the key role of ethics and law in the field of biomedical science and technology, by restricting scientific research behavior, protecting the rights and safety of subjects, providing a solid guarantee for scientific research activities, and promoting the healthy development of biomedical science and technology. At the same time, the positive role of ethics and law in promoting international cooperation and exchange of biomedical science and technology is also discussed, which will inject strong impetus into the global development of biomedical science and technology. In addition, through case analysis, the paper demonstrates the key role of ethical review in the field of biomedical science and technology, as well as the importance of law in maintaining market order, protecting subjects' rights and interests, and fairness and justice. The successful practice of ethics and law in the development of biomedical science and technology is emphasized, which proves that following ethical principles and legal framework is the key factor to promote the progress of biomedical science and technology. This paper explores the important role of ethics and law in the development of biomedical science and technology, and provides valuable reference and guidance for practitioners in the industry. By following ethical principles and legal norms, we will jointly promote the prosperity and development of biomedical science and technology, and contribute to the common progress of human health.

Background: Occupational accidents contribute 46-65% of hepatitis B virus (HBV) infections among healthcare workers (HCWs). Vaccine against HBV infection offers protection of more than 90%. Despite availability of the vaccines in Tanzania, it’s uptake among HCWs in primary health facilities remains understudied. This study explored HBV vaccine uptake and associated factors among HCWs in rural and urban settings of north western Tanzania. Methodology: A cross-sectional analytical study was conducted between June and July in 2022 among HCW in Misungwi and Ilemela districts. Data were collected using a self-administered questionnaire and analyzed using IBM SPSS® version 25. Results: A total of 402 HCWs were recruited, their mean age was 34.9±7.77 years. Approximately half (54.7% (220/402) of HCWs had received at least one shot of HBV vaccine with only (18% (76/402) being fully vaccinated. Ilemela showed significantly higher uptake (χ2=23.64, df=1, p=0.00) of HBV vaccine as compared to their counterparts in Misungwi. Being male (aOR=2.38, 95% CI 1.28-4.45, p=0.006), working in urban (aOR=5.75, 95% CI 2.91-11.35, p=0.00) and employment duration of more than two years (aOR=3.58, 95%CI 1.19-10.74, p=0.023) were significantly associated with higher odds of HBV vaccination. Moreover, high perceived susceptibility to HBV infection (aOR=2.20, 95% CI1.02-4.75, p=0.044) and history of needle prick injuries (aOR=6.87, 95%CI 3.55-13.26, p=0.00) were also significantly associated with higher odds of HBV vaccination. Conclusion: There was low uptake of HBV vaccine among HCW in primary health facilities with a noteworthy difference between rural and urban settings.. Therefore, advocacy campaigns as well as resource mobilization towards promotion of HBV vaccination in primary health facilities are pivotal.

ABSTRACT. In this paper, we run for all INDIA mutations and variants a biomathematical numerical method for analysing mRNA nucleotides sequences based on UA/CG Fibonacci numbers proportions (Perez, 2021). In this study, we limit ourselves to the analysis of whole genomes, all coming from the mutations and variants of SARS-CoV2 sequenced in India in 2020 and 2021. We then demonstrate - both on actual genomes of patients and on variants combining the most frequent mutations to the SARS-CoV2 Wuhan genomes and then to the B.1.617 variant - that the numerical Fibonacci AU / CG metastructures increase considerably in all cases analyzed in ratios of up to 8 times. We can affirm that this property contributes to a greater stability and lifespan of messenger RNAs, therefore, possibly also to a greater INFECTUOSITY of these variant genomes. Out of a total of 108 genomes analyzed: - None ("NONE") of them contained a number of metastructures LOWER than those of the reference SARS-CoV2 Wuhan genome. - Eleven (11) among them contained the same number of metastructures as the reference genome. - 97 of them contained a GREATER number of metastructures than the reference genome, ie 89.81% of cases. The average increase in the number of metastructures for the 97 cases studied is 4.35 times the number of SARS-CoV2 UA/CG 17711 Fibonacci metastructures. Finally, we put a focus on B.1.617.2 crucial exponential growth Indian variant. Then, we demonstrate, by analyzing the main worldwide 19 variants, both at the level of spikes and of whole genomes, how and why these UA / CG metastuctures increase overall in the variants compared to the 2 reference strains SARS-CoV2 Wuhan and D614G.

Food allergies are a growing public health concern worldwide, especially in children and young adults. Allergen-specific IgE plays a central role in the pathogenesis of food allergies, but their titers poorly correlate with allergy development. Host immune systems yield allergen-specific immunoglobulin (Ig)A, IgE and IgG subclasses with low or high affinities and differential Fc N-glycosylation patterns that can affect the allergic reaction to food in multiple ways. High affinity IgE is required to induce strong mast cell activation eventually leading to allergic anaphylaxis while low affinity IgE can even inhibit the development of clinically relevant allergic symptoms. IgA and IgG antibodies can inhibit IgE-mediated mast cell activation through various mechanisms, thereby protecting IgE-positive individuals from allergy development. The production of IgE and IgG with differential allergenic potential seems to be affected by the signaling strength of individual B cell receptors, and by cytokines from T cells. This review provides an overview of the diversity of the B cell response and the diverse roles of antibodies in food allergy.

Chronic hepatitis B (CHB) infection and the Hepatitis B virus X protein (HBx) are major risk factors associated with hepatocellular carcinoma (HCC). In CHB infection, HBx induces mitochondrial dysfunction, exhaustion and impaired function in hepatocytes. Restoring hepatocyte health along with reduction in virus replication could be an ideal treatment for CHB. Thiourea derivatives are well known for their antiviral property though their effect on mitochondrial and/ or hepatocyte health remains obscure. This study focus on the repurposing of thiourea derivatives (DSA-00, DSA-02, and DSA-09) on hepatocyte replenishment. HepG2.2.15 cells were treated with thiourea derivatives, alongside Entecavir (ETV). The proteomics analysis showed both DSA-00 and ETV were enriched with proteins associated with antiviral responses. In addition, DSA-00 additionally showed increase in proteins linked to mitochondrial response. Whereas DSA-02 exhibited association with innate immune system and citric acid cycle and DSA-09 displayed pathways similar to DSA-00 and ETV. Treated groups exhibited enhanced bio-energetic and antiviral response as compared to the untreated group. FACS analysis revealed the restoration of exhausted hepatocytes by thiourea derivatives through targeting mitochondria. Our findings suggest that thiourea derivatives hold potential as a novel therapeutic agent that seems to restore mitochondrial health along with anti-viral response in CHB.

Background/methods: For mechanistic studies, in vitro human B cell differentiation and generation of plasma cells are invaluable techniques. However, the heterogeneity of both T cell-dependent (TD) and T cell-independent (TI) stimuli and the disparity of culture conditions used in existing protocols makes interpretation of results challenging. The aim of the present study was to achieve the most optimal B cell differentiation conditions using isolated CD19⁺ B cells and PBMC cultures. We addressed multiple seeding densities, different durations of culturing and various combinations of TD stimuli and TI stimuli including B cell receptor (BCR) triggering. B cell expansion, proliferation and differentiation was analyzed after 6 and 9 days by measuring B cell proliferation and expansion, plasmablast and plasma cell formation and immunoglobulin (Ig) secretion. In addition, these conditions were extrapolated using cryopreserved cells and differentiation potential was compared. Results: This study demonstrates improved differentiation efficiency after 9 days of culturing for both B cell and PBMC cultures using CD40L and IL-21 as TD stimuli and 6 days for CpG and IL-2 as TI stimuli. We arrived at optimized protocols requiring 2500 and 25.000 B cells per culture well for TD and TI assays, respectively. The results of the PBMC cultures were highly comparable to the B cell cultures, which allows dismissal of additional B cell isolation steps prior to culturing. In these optimized TD conditions, the addition of anti-BCR showed little effect on phenotypic B cell differentiation, however it interferes with Ig secretion measurements. Addition of IL-4 to the TD stimuli showed significantly lower Ig secretion. The addition of BAFF to optimized TI conditions showed enhanced B cell differentiation and Ig secretion in B cell but not in PBMC cultures. With this approach, efficient B cell differentiation and Ig secretion was accomplished when starting from fresh or cryopreserved samples. Conclusion: Our methodology demonstrates optimized TD and TI stimulation protocols for more indepth analysis of B cell differentiation in primary human B cell and PBMC cultures while requiring low amounts of B cells, making them ideally suited for future clinical and research studies on B cell differentiation of patient samples from different cohorts of B cell-mediated diseases.

Centromeres, the chromosomal loci where spindle fibers attach during cell division to segregate chromosomes, are typically found within satellite arrays in plants and animals. Satellite arrays have been difficult to analyze because they comprise megabases of tandem head-to-tail highly repeated DNA sequences. Much evidence suggests that centromeres are epigenetically defined by the location of nucleosomes containing the centromere-specific histone H3 variant cenH3, independently of the DNA sequences where they are located; however, the reason that cenH3 nucleosomes are generally found on rapidly evolving satellite arrays has remained unclear. Recently, long read sequencing technology has clarified the structures of satellite arrays and sparked rethinking of how they evolve, while new experiments and analyses have helped bring both understanding and further speculation about the role these highly repeated sequences play in centromere identification.

Frailty, an age-related decline in homeostatic reserves, markedly proceeded during the coronavirus disease 2019 pandemic. To continuously assess frailty status, a remote system is urgently required. We aimed to co-design/co-develop an online frailty check (FC) application alongside FC supporters who were facilitators in a pre-existing onsite FC program. The online FC included a screening measurement for sarcopenia and an 11-item questionnaire covering dietary, physical, and social behaviors. Using prototype applications, 55 opinions obtained from 32 FC supporters (median 74.0 years) were categorized and reflected refinement. Regarding the self-efficacy of FC supporters, a significant increase in social positioning was seen after the mock test (P=.031). For FC supporters and participants, the average system usability scale (SUS) score was 70.2±10.3 points, which was “marginally high” for acceptability and “good” for the adjective range. Multiple regression analysis showed that the SUS score was significantly correlated with online-onsite reliability but not online communication, even after adjusting by age, sex, education level, and ICT proficiency (b=0.400, 95% CI: 0.243-1.951, P=.013). Additionally, a significant association between onsite and online FC scores was observed (R=0.670, P=.001). Our online FC application was evaluated to be a valuable tool to practically assess frailty status remotely.

This study explores the potential of natural compounds, including Daidzin, Luteolin, and Silibinin, as inhibitors of human monoamine oxidase B (MAO-B) for the treatment of Parkinson's disease. Docking simulations were performed using Autodock Vina with Pyrx program to evaluate the binding affinities of these compounds with MAO-B. Results indicate that Daidzin, Luteolin, and Silibinin exhibit promising binding affinities with MAO-B, with Daidzin demonstrating the highest affinity. Toxicity parameters were further predicted using the PkCSM Server, confirming the low toxicity of these compounds. Overall, the findings suggest that Daidzin, Luteolin, and Silibinin have the potential to be effective and safe treatments for Parkinson's disease through their inhibition of MAO-B. Further experimental validation is warranted to support their therapeutic efficacy in clinical settings.

: (1) Background: Hepatitis B core antibodies (anti-HBc) are a marker of hepatitis B virus (HBV) exposure; hence a normal HBV serology profile is characterized by HBV surface antigen (HBsAg) and anti-HBc positivity. However atypical HBV serologies occur and we aimed to determine the prevalence of an atypical profile (HBsAg+/anti-HBc-) in a cohort of people with HIV-1 (PWH) in Botswana. (2) Methods: Plasma samples from an HIV-1 cohort in Botswana (2013-2018) were used. Samples were screened for HBsAg and anti-HBc. Next generation sequencing was done using the GridION platform. Wilcoxon rank-sum test and Chi-squared tests were used for comparison of continuous and categorical variables respectively. (3) Results: HBsAg+/anti-HBc- prevalence was 13.7% (95% CI 10.1 – 18.4) (36/263). HBsAg+/anti-HBc- participants were significantly younger (p&lt;0.001), female (p=0.02), ART naïve (p=0.04) and had detectable HIV viral load (p=0.02). There were no mutational differences in sequences isolated from participants with HBsAg+/anti-HBc- versus those with HBsAg+/anti-HBc+ serology. (4) Conclusions: We report a high HBsAg+/anti-HBc– atypical serology profile prevalence among PWH in Botswana. We caution against HBV testing algorithms that consider only anti-HBc+ samples for HBsAg testing as they are likely to underestimate HBV prevalence. Studies to elucidate the mechanisms and implications of this profile are warranted.

Rare diseases are characterized by a wide diversity of signs and symptoms and vary not only from disease to disease, but also from person to person, and living with a disease leads patients to peculiar experiences and treatments, without limits of time and space, as they extend to various environments and relationships of their lives. The objective of this study is the theoretical interaction between Value Co-creation (VC) and the Stakeholder Theory (ST) with the Shared Decision Making (SDM) health care theory. It is configured as a multiparadigmatic proposal by enabling the analysis of multiple perspectives of different stakeholders in health care. Thus, Co-created Decision Making (CDM) emerges in a logic dominated by service, with emphasis on intangible aspects and the interactivity of the relationships. It goes beyond the clinical office and the doctor-patient relationships, as studied in SDM, extending to all environments and interactions that add value to the patient's treatment. It was concluded that the essence of this new theory proposed here is neither in patient-centered care nor in patient self-care, but in co-created relationships with and between stakeholders in both directions, including non-health care environments that are important to the patient, such as relationships with friends, family, other patients with the same disease, social media, public policies, and the practice of pleasurable activities.

Recently, many authors have been interested to introduce fuzzy implications over t-norms and t-conorms. In this paper, we introduce (S,N) and residuum fuzzy implication for Dubois t-norm and Hamacher's t-norm. Also, new concepts so-called (T,N) and residual fuzzy co-implication in dual Heyting Algebra are investigated. Some examples as well as application are discussed as well.

Background: Antibiotic resistance is an urgent issue everywhere in the globe. It is necessary to look into new sources of antibiotics to address this issue. Aim of the study: studying the purification of Corallopyronin B from various soil conditions in Egypt, as well as the antibacterial effectiveness of Corallopyronin B in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Several soil conditions in Egypt were examined to create bacterial isolates that generated the antibiotic chemical Corallopyronin B. Using reversed-phase HPLC, Myxopyronin B was purified. The test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity were ascertained using the paper disc diffusion assay and the broth microdilution technique. Furthermore, in stages 1/2 of randomized clinical trials including human and animal models, pharmacokinetics, adverse drug reactions, and the in vivo antibacterial spectrum were discovered. Results: The soil bacterial isolate Corallococcus coralloides DSM 2259, which was grown on a Casein yeast peptone( CYP) plate, produced Corallopyronin B from its culture supernatant. At MICs more than 100 mcg/ml, the test antibiotic inhibited the growth of many Gram -ve bacteria, including Escherichia coli, while also preventing the growth of numerous Gram +ve bacteria, with MICs ranging from 1 to 10 mcg/ml. Eukaryotic cells, on the other hand, including those in humans and fungi, were unharmed. The test antibiotic was shown to have a bactericidal effect by inhibiting bacterial DNA-dependent RNA polymerase( RNLP). In phases 1/2 of randomized human clinical trials, when 600 mg of the dose per 70 kg of body weight was administered SC, the Cmax was 8.6 mcg/ml at Tmax 1 hour; T1/2 reached 136 min following first-order kinetics of elimination. It stopped acting around 6-7 hours after SC was administered. In the preclinical and randomized human clinical trial phases 1/2, less than 6 percent of experimental candidates had uncommon toxicity, which showed up as reduced bile flow. Protein binding with plasma albumin was detected which reached about 83%. Conclusion: The current work was noteworthy since it involved the production of the bactericidal antibiotic Corallopyronin B from Corallococcus coralloides DSM 2259 which was isolated from several soil environments in Egypt.

Background: Diffuse large B-cell lymphoma is the most common type of non-Hodgkin's lymphoma. Due to the variety of clinical manifestations, accurate diagnosis can be challenging. Here, we present a case of DLBCL that was initially misdiagnosed as a hematoma, highlighting the importance of considering malignancy in the setting of non-responsive soft tissue swelling. Methods: A 76-year-old man presented to the emergency department with right periorbital swelling and ecchymosis. The symptoms first appeared after an injury and did not resolve spontaneously. The patient was taking warfarin for atrial fibrillation. A facial bone CT revealed a large irregular homogeneous mass. An extraconal hematoma was suspected based on clinical history and radiologic findings. Incision and drainage were performed, resulting in evacuation of old blood. Despite continued drainage, the patient's symptoms worsened. A comparison with the previous CT revealed an increase in the size of the lesion. As a result, a surgical excisional biopsy was performed. Results: Biopsy of the mass showed a diffuse infiltrate of lymphocytes around the tissue. The diagnosis of diffuse large B-cell lymphoma was confirmed pathologically. The patient was referred to hematology for further management. Conclusions: DLBCL is a rare disease associated with a poor prognosis. Due to the previous injury and the use of anticoagulants, the patient was initially misdiagnosed as having a hematoma. This delayed the prompt diagnosis and affected the timing of treatment initiation. We must be aware that a malignant mass is a potential cause of unresponsive soft tissue swelling.

The aim this text to present the confined covariant quark model (CCQM) and review its applications to the decays of B mesons. We do so in the context of existing experimental measurements and theoretical results of other authors, which we review also. The physics principles are in detail exposed for the CCQM, the other results (theoretical and experimental) are surveyed in an enumerative way with comments. We proceed by considering successively three categories of decay processes: leptonic, semileptonic and non-leptonic.

IQGAP1 is a multi-functional scaffold protein. However, its role in B cell development and function is not known. Here, we demonstrate Iqgap1mice contained significantly increased numbers of B220+ B, B220+IgM pro/pre-B, and B220+IgM+ immature-B cells in the bone marrow. Here, we show IQGAP1 as the essential scaffold that regulates early B cell development and function. Iqgap1mice contained significantly increased numbers of B220+ B, B220+IgM pro/pre-B, and B220+IgM+ immature-B cells in the bone marrow. New-forming and follicular B cell numbers were increased, while the marginal zone B cell numbers were significantly reduced in the spleen of the Iqgap1mice. Lack of IQGAP1 reduced T-dependent and T-independent humoral responses. Mechanistically, the lack of IQGAP1 considerably decreased the phosphorylation of Mek1/2, Erk1/2, and Jnk1/2. B cells from Iqgap1mice failed to suppress IL-7R-mediated activation of Stat5a/b, an essential step for cell-cycle exit and initiate light-chain recombination, leading to a reduction in RS rearrangement frequency. Lack of IQGAP1 resulted in a significant reduction of IRF4 and IRF8 in BM B cells. Our study provides the first evidence that IQGAP1-based signalosome is essential for the development and functions of B cells.

Rising raw material prices can have a significant impact on the financial performance of the food and beverage (F&B) business. The purpose of this study was to determine the impact of rising prices of staples onfinancial resilience F&B business in Indonesia. This study uses a quantitative approach with bivariate correlation analysis and secondary data from the financial reports of F&B companies listed on the Indonesia Stock Exchange for the 2020-2022 period. The results showed that the increase in the price of basic commodities had a significant positive impact onfinancial resilience F&B company. This can be seen from the decline in the profitability and liquidity of F&B companies as a result of the increase in the price of basic commodities. Therefore, F&B companies must pay attention to and manage the risk of rising prices of basic commodities to maintainfinancial resilience and sustainable business continuity.

Autoimmune disorders and some types of blood cancer originate when B lymphocytes malfunction. In particular, when B cells produce antibodies recognizing the body’s proteins, it leads to various autoimmune disorders. And when B cells of various developmental stages transform into cancer cells, it results in blood cancers, including multiple myeloma, lymphoma, and leukemia. Thus, new methods of targeting B cells are required for various patient groups. Here, we used protein kinase inhibitors alectinib, brigatinib, ceritinib, crizotinib, entrectinib, and lorlatinib previously approved as drugs treating anaplastic lymphoma kinase (ALK)-positive lung cancer cells. We hypothesized that the same inhibitors will efficiently target leukocyte tyrosine kinase (LTK)-positive, actively protein-secreting mature B lymphocytes, including plasma cells. We isolated CD19-positive human B cells from the blood of healthy donors and used two alternative methods to stimulate cell maturation toward plasma cells. Using cell proliferation and flow cytometry assays, we found that ceritinib and entrectinib eliminate plasma cells from B cell populations. Alectinib, brigatinib, and crizotinib also inhibited B cell proliferation, while lorlatinib had no or limited effect on B cells. More generally, we concluded that several drugs previously developed to treat ALK-positive malignant cells can be also used to treat LTK-positive B cells.

The population of Bifidobacterium spp in faecal samples from breast-fed and formula-fed infants were investigated and developed antibiogram. The common bacterial growth media such as Man Rogos Sharpe (MRS), Brain Heart Infusion (BHI), Luria Bertani (LB) broth and Bifidobacteria agar were evaluated by the enumeration of Bifidobacterium spp. in faecal material. The results demonstrated that the population of Bifidobacterium spp. in the faecal samples of breast-fed infants is numerically high and, low in formula-fed infants. Phylogenetic analysis of the 16S rRNA, (Xylose/Fructose-6-phosphate phosphoketolase) xfp, and RFLP map of Bifidobacteria isolates suggested a presence of possible new and different Bifidobacterium spp. The intensity of the reddish brown colour formed during the f6ppk (Fructose-6-phosphate phosphoketolase) assay confirms the presence of variable Bifidobacteria. The highest recovery and diversity of Bifidobacteria were obtained from Bifidobacteria agar media. Growth in various media resulted in the formation of small (SCV) and big colony variants (BCV). We understand that the various antibiotic minimum inhibitory concentration (MIC) values obtained by applying different media, growth conditions, after bile salt treatment, and at low pH can vary. This study concludes that the variation of microbiological conditions differentiating resistant and susceptible strains is influenced by the test conditions as well.

Influenza B virus (IBV) is a major respiratory pathogen of humans, particularly in the elderly and children and vaccines are the most effective way to control it. In previous work, incorporation of two mutations (E580G, S660A) along with the addition of a HA epitope tag in the PB1 segment of B/Brisbane/60/2008 (B/Bris) resulted in an attenuated strain that was safe and effective as a live attenuated vaccine. A third attempted mutation (K391E) in PB1 was not always stable. Interestingly, viruses that maintained the K391E mutation were associated with the mutation E48K. To explore the contribution of the E48K mutation for stability of the K391E mutation, a vaccine candidate was generated by inserting both mutations along with attenuating mutations E580G and S660A in PB1 of B/Bris (B/Bris PB1att 4M). Serial passage of the B/Bris PB1att 4M vaccine candidate in eggs and MDCK indicated high stability. In silico structural analysis revealed a potential interaction between amino acids at positions 48 and 391. In mice, B/Bris PB1att 4M was safe and provided complete protection against homologous challenge. These results confirm the compensatory effect of mutation E48K to stabilize the K391E mutation, resulting in a safer, yet still protective, IBV LAIV vaccine.

Power converter technologies have become increasingly vital in various applications due to their efficient management of electrical energy. With the growing prominence of renewable energy sources like solar and wind, the high penetration of power electronic converters has been justified. However, ensuring power quality has emerged as a significant challenge for grid-connected power converters. The divergence from the ideal sinusoidal waveform in terms of magnitude and frequency impacts both grid-side currents and voltages. Several studies have proposed solutions to address power quality issues at the load side. The advancement of power converters has been fueled by the development of high-performance microprocessors and the emergence of high-speed switching devices, such as SiC-MOSFETs. This paper focuses on the design of voltage source converters, particularly those based on SiC-MOSFET semiconductor devices. The article presents the design of H-Bridge cells, discusses two-level voltage source converters based on cascade H-Bridge cells in parallel configuration with experimental fault analysis, addresses the seven-level voltage source converters topology, and explores the design and experimental results of the matrix converter. The findings underscore the importance of considering the entire converter design for improved performance at high switching frequencies. The article concludes by summarizing the main outcomes and implications of this research.

As one of the important components of underwater propulsion systems, water lubricated bearings are often failure due to mechanical wearing and vibrating, especially under high loads and prolonged friction. In this paper, a dual-network co-crosslinking strategy based on HNBR is proposed, in which the epoxy network connects with the rubber network through Epoxidized Eommia ulmoides gum. The damping, tribological and mechanical properties of the prepared composite are systematically investigated. The results show that this material has excellent friction and vibration damping properties, with a water-lubricated coefficient of friction as low as 0.022 and a wear resistance as high as 3.87 × 10-6mm3/Nm. Preparing HNBR-based composite by dual network co-crosslinked is proved being a feasible solution to improve the reliability and service life of water-lubricated bearings.

The 2022-2023 influenza season in Romania was characterized by high pediatric hospitalization rates, predominated by influenza A subtypes H1N1 and H3N2. Lowered population immunity to influenza after the SARS-CoV-2 pandemic and subsequent stoppage of influenza circulation, particularly in children who had limited pre-pandemic exposures, influenced hospitalization among children immunosuppressed, and patients with concurrent medical conditions who are at increased risk for developing severe forms of influenza. This study focused on the characteristics of influenza issues among paediatric patients, as well as the relationship between different influenza virus types and viral and bacterial coinfections and illness severity in the 2022-2023 season after the SARS-CoV-2 pandemic. We conducted a retrospective clinical analysis on 301 cases of influenza in pediatric inpatients (age ≤ 18 years), hospitalized at the National Institute of Infectious Diseases "Prof. Dr. Matei Balș" IX Pediatric Infectious Diseases Clinical Section between October 2022 and February 2023. The most significant age group was 57.8% representing children between one to four years old and female. The average clinical forms were found in 61.7%, whereas severe versions represented 18.2% of cases. Most of the complications were respiratory (acute interstitial pneumonia, 76.1%), hematological (72.1%), represented by intra-infectious and deficiency anemia, leukopenia, thrombocytopenia), 33.6% were digestive, such as diarrheal disease, liver cytolysis syndrome, and the acute dehydration syndrome associated with electrolyte imbalance (71.4%). Severe complications were associated with a risk of unfavorable evolution: acute respiratory failure and neurological complications (convulsions, encephalitis). No deaths were reported. We noticed that the flu season 2022-2023 was characterized by the association of co-infections (viral, bacterial, fungal and parasitic) more frequent than in previous years (26.2% vs. 16%), which evolved more severely, with prolonged hospitalization and more complications (p<0.05), and time of use of oxygen therapy was statistically significant (p > 0.05); influenza vaccination in this group was zero. In conclusion, coinfections with respiratory viruses increase the severity of the pediatric population's immunity to influenza, especially among young children who are more vulnerable to developing a serious illness. All people above the age of six months should get vaccinated against influenza to prevent the illness and its severe complications.

Recently, the amount of waste generated has been rapidly increasing, there have been difficulties disposing of waste in Korea. As a solution to this, treating waste using a cement kiln has suggested, but the environmental and economic effects have not been specifically studied. In this study, the effects of alternative resources, and reducing the social costs(Installation and Operation) associated with waste treatment facilities were analyzed. Through a co-processing method, a reduction of approximately 53kg of CO2 can be realized during the production of one ton of cement, and cost savings of about 3,815 milion USD. Another effect is an extension of the expiration date for landfills by 7.55 years.

New setting is introduced to study quasi-degree and quasi-co-degree arising from co-neighborhood. quasi-degree and quasi-co-degree is about a vertex which are applied into the setting of neutrosophic graphs. . The structure of set is studied and general results are obtained. Also, some classes of neutrosophic graphs namely path-neutrosophic graphs, cycle-neutrosophic graphs, complete-neutrosophic graphs and star-neutrosophic graphs, complete-bipartite-neutrosophic graphs and complete-multipartite-neutrosophic graphs are investigated in the terms of a vertex which is called either quasi-degree or quasi-co-degree. Neutrosophic number is reused in this way. It’s applied to use the type of neutrosophic number in the way that, three values of a vertex are used and they’ve same share to construct this number to compare with other vertices. Summation of three values of vertex makes one number and applying it to a comparison. This approach facilitates identifying vertices which form quasi-degree and quasi-co-degree. Quasi-degree is a value of a vertex which is maximum amid all values of vertices which are neighbors to a fixed vertex. Quasi-co-degree is a value of an edge which is maximum amid all values of edges which are neighbors to a fixed vertex but corresponded vertex is representative for this notion. Using different values which are related to a vertex inspire us to focus on edge and vertices which are corresponded to a fixed vertex. The notion of neighborhood is used to collect either vertices are titled neighbors or edges are incident to fixed vertex. In both settings, some classes of well-known neutrosophic graphs are studied. Some clarifications for each result and each definitions are provided. Using fixed vertex has key role to have these notions in the form of vertex or edge. The value of an edge has eligibility to call quasi-co-degree but the value of a vertex has eligibility to call quasi-degree. Some results get more frameworks and perspective about these definitions. The way in that, two vertices have connection together, open the way to define neighborhood and co-neighborhood. The maximum values in neighborhood and co-neighborhood introduces quasi-degree and quasi-co-degree, respectively. New name is chosen from degree. Since amid all vertices with different degrees, one vertex is chosen. In other words, one vertex is fixed and its degree turns out quasi-degree where two degrees could be assigned to a vertex. Degree of edges and degree of vertices. The number of edges which are incident to the vertex and the number of vertices which are neighbors to the vertex. Degree and co-degree are the notions which are transformed to use in quasi-style. Two neutrosophic values introduce two neutrosophic vertices separately in each settings. These notions are applied into neutrosophic graphs as individuals but not family of them as drawbacks for these notions. Finding special neutrosophic graphs which are well-known, is an open way to purse this study. Some problems are proposed to pursue this study. Basic familiarities with graph theory and neutrosophic graph theory are proposed for this article.

Potential of co-digestion mixing thickened secondary sludge (TS) from extended aeration wastewater treatment plant and locally available substrates (whey, grease and septage) has been studied using three steps. The first step was a batch test to determine biological methane potential (BMP) of different mixtures of the three co-substrates with TS. The second step has been carried out with lab-scale reactors (20 L) simulating anaerobic continuous stirred tank reactors fed by three mixtures of co-substrates determined according to previous step results. Modelling using ADM1 as a mechanistic model was applied in the third step to help understanding the co-digestion process. According to BMP step, septage used as co-substrate has a negative effect on performance and addition of 10 to 30% grease or 10% whey would lead to a higher production of biogas and with an increase of the methane content. The results from the reactor showed less evi-dence of the positive effects observed with the BMP assay. Protein and lipid fractions of particu-late biodegradable COD are important variables for digester stability and methane production as predicted by modelling. Results of simulations with ADM1 model adapted to co-digestion confirmed that this model is a powerful tool to optimize the process of biogas production.

There is compelling evidence that the nuclear receptor TRβ, a member of the thyroid hormone receptor (TR) family, is a tumor suppressor in thyroid, breast and other solid tumors. Cell-based and animal studies reveal that the liganded TRβ induces apoptosis, reduces an aggressive phenotype, decreases stem cell populations, and slows tumor growth through modulation of a complex interplay of transcriptional networks. TRβ-driven tumor suppressive transcriptomic signatures include repression of known drivers of proliferation such as PI3K/Akt pathway and activation of novel signaling (JAK1/STAT1) and metabolic reprogramming in both thyroid and breast cancers. The presence of TRβ is also correlated with a positive prognosis and response to therapeutics in BRCA+ and triple-negative breast cancers respectively. Ligand activation of TRβ enhances sensitivity to chemotherapeutics. TRβ co-regulators and bromodomain-containing chromatin remodeling proteins are emergent therapeutic targets. This review considers TRβ as a potential biomolecular diagnostic and therapeutic target.

The sense of uncertainty and fragility due to the effects and magnitude of global challenges we are facing (from pandemic circumstances to climate change impacts) requires – much more than in the past – the capacity to generate a visionary and forefront design approach in the young gen-erations aiming at stimulating their reaction attitude rather than providing consolidated tools from past conditions that no longer exist or will rapidly evolve. Within this general framework, we have investigated the effectiveness and impacts of experienced-based methods of learning and innovative educational tools in architecture aimed at shaping expertise in which the environ-mental dimension and the climate-change challenge dialogues with the context's complexity in terms of socio-cultural dynamics, real potentialities and constrains, addressing their transdisci-plinary trajectories. The paper analyses 5 international pioneering teaching experiences that provide the opportunity to understand the outcomes of collaborative and experiential learning processes in which the educational activities leverage a dialogue between diverse communities (academia-citizens-policymakers-practitioners). The study outcomes show that shifting the pedagogical paradigm towards in-field-experience-based models can improve the awareness of future practitioners for climate implications of architectural design, implement their analysis and project skills while triggering processes of knowledge transfer and co-production at community level, and allow them to better address the societal and cultural issues involved within decision making.

The purpose of this study is to explore conceptual approaches in co-production studies and to examine current research trends of the study. The conceptual paper includes research articles related to co-production in public administration field. By thoroughly scrutinizing 32 research works of co-production, this study highlights major loopholes in the field of the study. The contributions of the study are: (1) identifying two common characteristics of co-production, (2) categorising three types of co-producing by end-users, and (3) finding that goals and success of co-production are more beneficial for service providers though its initial approach is citizen-centric approach. We suggest that future studies should be (1) to focus on reasons for co-production failures or success, (2) to discover further hindrances for co-production in service production, (3) to examine influencing factors on service providers as well as institutional impacts on co-production process, and (4) to include practical assessment in co-production study.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

Background: Previously, our laboratory has provided evidence that pre-administration of the antioxidant, lipoic acid covalently bonded to various naturally occurring antioxidants, enhanced neuroprotective capacity compared to the administration of lipoic acid on its own. The naturally occurring compound scopoletin, a coumarin derivative, has been shown in various in vitro studies to have both antioxidant and anti-inflammatory mechanism of actions. To date, the effect of scopoletin on neuronal cell death in an in vivo model of ischemia or ischemia-reperfusion has not been investigated. Therefore, the present investigation was designed to determine if scopoletin on its own, or a co-drug consisting of lipoic acid and scopoletin covalent bond, named UPEI-400, would be capable of demonstrating a similar neuroprotective efficacy. Methods: Using a rodent model of stroke in male rats (anesthetized with Inactin®; 100 mg/kg, iv), the middle cerebral artery was permanently occluded for 6 hours (pMCAO), or in separate animals, occluded for 30 min followed by 5.5 hrs of reperfusion (ischemia/reperfusion; I/R). Results: Pre-administration of either scopoletin or UPEI-400 significantly decreased infarct volume in the I/R model (p<0.05), but not in the pMCAO model of stroke. However, UPEI-400 was ~1000 times more potent as compared to scopoletin on its own. The optimal dose of UPEI-400 was then injected during the occlusion and at several time points during reperfusion and significant neuroprotection was observed for up to 150 mins following the start of reperfusion (p<0.05). Conclusion: The data suggest that synthetic combination of scopoletin with lipoic acid (UPEI-400) is a more effective neuroprotectant that either compound on their own. Also, since UPEI-400 was only effective in a model of I/R, it is possible that it may act to enhance neuronal antioxidant capacity and/or upregulate anti-inflammatory pathways to prevent the neuronal cell death.

Poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) named further PVBA was investigated as protective coating for copper corrosion in 0.9 % NaCl solution using electrochemical measurements such as, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization associated with Atomic Force Microscopy (AFM). The PVBA coating on the copper surface (Cu-PVBA) was modeled in methanol containing PVBA. Its inhibitory properties against corrosion was comparatively discussed with those of the copper sample treated in methanol without polymer (Cu-Me) and of untreated sample (standard copper). A protective performance of PVBA coating of 80 % was computed from electrochemical measurements, for copper corrosion in NaCl solution. Also, AFM images designed a specific surface morphology of coated surface with PVBA, clearly highlighting a polymer film adsorbed on the copper surface, which presents certain deterioration after corrosion, but metal surface was not significantly affected compared to those of untreated samples or treated in methanol, in the absence of PVBA.

Systematic results of lattice dynamical calculation are reported for the novel (SiC)m/(GeC)n superlattices (SLs) by exploiting a modified-linear chain model (M-LCM) and a realistic rigid-ion- model (RIM). By employing the bond polarizability method in the framework of M-LCM, we have simulated Raman intensities for the graded (SiC)10-D/(Si0.5Ge0.5C)D/(GeC)10-D/(Si0.5Ge0.5C)D SLs by carefully integrating interfacial layer thickness D (≡ 0, 1, 2, 3 monolayers (MLs)). The variation of D has initiated considerable up (down) shifts of GeC-, (SiC)-like Raman peaks in the middle of the optical phonon frequency region. With D = 3 MLs, the maximum energy shift (by ~ 47 cm-1) of SiC-like modes has caused substantial changes in the Raman intensity profiles linked to the localization of atomic displacements at the interfacial transition regions. This effect can be considered as a vital tool for authenticating the interfacial structures in technologically important SLs. By using a RIM, we have reported SL phonon dispersions along the growth [001] as well as in the plane [100], [110] perpendicular to the growth. Our simulations of phonons in the acoustic mode region have not only confirmed the formation of minigaps at the zone center and zone edges but also provided evidence of anti-crossing and phonon confinement. Besides examining angular dependence of zone-center optical modes, we have also discussed phonon folding, confinement and anisotropic behavior in (SiC)m/(GeC)n SLs.

New setting is introduced to study co-neighborhood, neutrosophic t-neighborhood, neutrosophic quasi-vertex set, neutrosophic quasi-order, neutrosophic neighborhood, neutrosophic co-t-neighborhood, neutrosophic quasi-edge set, neutrosophic quasi-size, Neutrosophic number, neutrosophic co-neighborhood, co-neutrosophic number, quasi-number and quasi-co-number. Some classes of neutrosophic graphs are investigated.

Protein Kinase C delta (PKCδ) has emerged as a key protective molecule against systemic lupus erythematosus (SLE or lupus), an autoimmune disease characterized by anti-double stranded (ds) DNA IgGs. Although PKCδ deficient mice and lupus patients with mutated PRKCD genes clearly demonstrate the requirement of PKCδ for preventing lupus autoimmunity, this critical tolerance mechanism remains poorly understood. We recently reported that PKCδ selectively deletes anti-dsDNA B cells in the germinal center (GC), disclosing a key B cell tolerance mechanism that prevents lupus autoimmunity. PKCδ’s tolerance function is activated by sphingomyelin synthase 2 (SMS2), a lipid enzyme whose expression is generally reduced in B cells from lupus patients. Moreover, pharmacologic strengthening of the SMS2/PKCδ tolerance pathway alleviated lupus pathogenesis in mice. Here, we review relevant publications in order to provide mechanistic insights into PKCδ’s tolerance activity, and discuss the potential significance of therapeutically targeting PKCδ’s tolerance activity in the GC for selectively inhibiting lupus autoimmunity.

Presenting a case report on the occurrence of IgA nephropathy with hepatitis B infection in a 32-year-old male patient with main complaints of generalized weakness, easy fatigue, and bilateral swelling of the lower extremities. IgA nephropathy (IgAN), or Berger’s disease, is the most common primary glomerulonephritis worldwide. It is characterized by the formation of IgA1-containing circulating immune complexes and their deposition in the glomerular mesangium. Its etiology remains multifactorial and often idiopathic. IgA nephropathy alone does not have an infectious etiology; instead, it usually develops in conjunction with an infectious condition that triggers a dysregulated immune response. There is no proof that any particular infectious agent is the secondary cause of IgA nephropathy. Hepatitis B virus (HBV) infection is an infectious agent associated with renal complications, including IgA nephropathy. Symptoms include gross haematuria and mild proteinuria indicative of renal involvement. Laboratory investigations and serological tests are followed by imaging studies such as ultrasound and renal biopsy to confirm the diagnosis. The challenges encountered during the diagnostic process included overlapping symptoms and limitations of available diagnostic tests, highlighting the need for comprehensive diagnostic evaluation and multidisciplinary management approaches in similar cases. This case underscores the importance of recognizing and managing both conditions simultaneously to prevent long-term complications such as end-stage renal disease.

Anti-inflammatory agents are widely used for the treatment of inflammatory diseases. Nevertheless, the associated side effects of available drugs make necessary the search for new anti-inflammatory conditions. Here, we investigated the anti-inflammatory activity of solidagenone. Initially, we observed that a single dose of 30, 60 or 90 mg/Kg of solidagenone did not result in mortality or elicit any discernible signs of toxicity in the animals. At the same doses, solidagenone promoted a significative reduction in the migration of neutrophils in an acute peritonitis model and decreased mortality in a lipopolysaccharide-induced endotoxic shock model. Interestingly, treatment with solidagenone conferred a protective effect against leukopenia and thrombocytopenia, hematological disorders commonly observed in sepsis conditions. In addition, treatment with all the doses of solidagenone promoted a significative reduction in nitric oxide, TNF-α, and IL-1β relative to the LPS-stimulated vehicle-treated cultures. Furthermore, gene expression and in silico analyses also supported the modulation of NF-κB pathway by solidagenone. Finally, in silico pharmacokinetics prediction indicated a favorable drugability profile for solidagenone. Taken together, the findings of the present investigation show that solidagenone exhibits significant anti-inflammatory properties in acute experimental models, potentially through the modulation of NF-κB signaling pathway.

Previous studies have shown that immunization within the first hours/days after birth promotes the shift from the intrauterine Th2 immune response toward the Th1 immunity resulting in lower risk of developing allergic diseases. We are currently conducting a prospective cohort study among 307 participants divided into groups based on their TB and hepatitis B vaccination status (vaccinated at birth, within the first 12 months of life or unvaccinated) and also based on whether the participants had factors contributing to the development of allergic diseases. In each group we assessed the fact of primary diagnosis of atopic dermatitis at 12 and 18 months of age. It was demonstrated that atopic dermatitis (AD) was diagnosed from birth to 12 months of age much less frequently in those infants who had received the tuberculosis (TB) vaccine from day 3 to day 7 and hepatitis B vaccine within the first 24 hours of birth, including newborns with a high risk of developing allergic diseases. The probability of onset of AD at 12 and 18 months was also lower in timely vaccinated children, even though a burdened allergic anamnesis starts playing a more central role in development of AD at this age. Our findings testify to the fact that timely BCG-M and hepatitis B vaccination can produce a protective effect against the onset of AD, yet this effect diminishes with aging.

To face the high tolerance of biofilms to antibiotics, it is urgent to develop new strategies to fight against these bacterial consortia. We describe here an innova-tive antibiofilm nano vector, consisting of a Dispersin B-permethylated-β-cyclodextrin/ciprofloxacin adamantly (DspB-β-CD/CIP-Ad). For this purpose, complexation assays between CIP-Ad and (i) unmodified β-CD and (ii) different derivatives of β-CD, that are 2,3-O-dimethyl-β-CD, 2,6-O-dimethyl-β-CD, and 2,3,6-O-trimethyl-β-CD were tested. A stoichiometry of 1/1 was obtained for the β -CD/CIP-Ad complex by NMR analysis. ITC experiments were carried out to determine Ka, ΔH, ΔS thermodynamic parameters of the complex between β-CD or its different derivatives in the presence of CIP-Ad. A stoichiometry 1/1 of β-CD/CIP-Ad complexes was confirmed with variable affinity according to the type of methylation. A phase solubility study showed increased CIP-Ad solubili-ty with CDs concentration, pointing out complex formation. The evaluation of the antibacterial activity of CIP-Ad and the 2,3-O-dimethyl-β-CD/CIP-Ad or 2,3,6-O-trimethyl-β-CD/CIP-Ad complexes was performed on S.epidermidis strains. MIC studies showed that the complex of CIP-Ad and 2,3-O-dimethyl-β-CD exhibited similar antimicrobial activity to CIP-Ad alone, while the interaction with 2,3,6-O-trimethyl-β-CD increased MIC values. Antimicrobial assays on S. epidermidis biofilms demonstrated that the synergistic effect observed with the DspB/CIP association was partly maintained with the 2,3-O-dimethyl-β-CDs/CIP-Ad complex. To obtain this "all in one" nano vector, able to destroy the biofilm matrix and release the antibiotic simultaneously, we covalently grafted DspB on three carboxylic permethylated CD derivatives with different length spacer arms. The strategy was validated by demonstrating that a DspB-permethylated-β-CD/ciprofloxacin-Ad nanovector exhibited efficient antibiofilm activity.

The CYSTM (cysteine-rich transmembrane module) protein family comprises small molecular cysteine-rich tail-anchored membrane proteins found in many eukaryotes. The Saccharomyces cerevisiae strains carrying the CYSTM genes YDRO34W-B and YBR056W-A (MNC1) fused with GFP were used to test expression of these genes under different stresses. The YBR056W-A (MNC1) and YDR034W-B genes are expressed under stress conditions caused by the toxic concentrations of heavy metal ions such as manganese, cobalt, nickel, zinc, cuprum, and 2.4-dinitrophenol uncoupler. YDR034W-B but not YBR056W-A is expressed under alkali and cadmium stresses. YBR056W-A is localized in intracellular membranes, while YDR034W-B is localized in the cytoplasmic membrane. The null-mutants in both genes demonstrated both decreased cell concentration and lytic phenotype when cultivated in the presence of excess manganese. This indicates the involvement of Mnc1 and YDR034W-B proteins in manganese detoxification, probably by complexation of its ion.

The World Health Organization estimated that around 66 thousand HBV are caused by needlestick injuries annually. Healthcare students should be aware of HBV transmission route and preventive measures. This study assessed the knowledge, attitudes, and practices toward HBV among Jordanian healthcare students and its associated factor. A cross-national study conducted from March to August. The participants were asked to complete the questionnaire. It had four sections: participants' sociodemographic, knowledge, attitudes, and practices about HBV. 2322 participants were enrolled, 67.9% were females, 26.4% were medical student, 35.9% were in the 3rd year. 40% of the participants held a high level of knowledge and attitude. 63.9% of participants had good practices toward HBV. Medical students in the last year of study, encountered HBV patients , had better knowledge. Male students from medicine college, encountered HBV patients and had extra HBV courses showed better attitude. High practice level was associated with being dentistry student, at 5th year, encountered HBV patient and extras HBV courses. This study demonstrated insufficient knowledge and attitudes toward HBV, the practices level toward HBV among healthcare students was promising. Subsequently, public health efforts should modify the knowledge and attitude gaps to reinforce awareness and minimizing risks of the infection.

Chronic Hepatitis B (CHB) Virus infection is major etiological factor for liver cirrhosis and/ or liver cancer. The viral protein, major contributor in predisposition of chronicity and Hepatocellular Carcinoma (HCC) is Hepatitis B x (HBx) protein. Its dynamic subcellular distribution to an extent determines its multifactorial role. It is a regulatory protein which modulates viral as well as host machinery in favours to HBV persistence. An insight on HBx stabilising factors is critical for therapeutic purpose. The precise role of HBx in the pathogenesis of Chronicity of HBV is not known. Summary: This review comprehensively summarizing different mechanisms and their regulation by HBx protein with respect to chronicity and HCC emphasising viral persistence. Key Messages 1. HBx is a key protein for viral persistence. 2. Dynamic subcellular distribution of HBx determines its function. 3. HBx modulates cellular machinery to favours HBV survival. 4. HBx affects various intermediary mechanisms contributing to disease progression. 5. HBx may be a potent target to prevent the disease progression towards HCC.

Cardiovascular disease (CVD) places a heavy burden on older patients and the global healthcare system. A large body of evidence suggests that exercise training is essential in preventing and treating cardiovascular disease, but the underlying mechanisms are not well understood. Here, we used the Drosophila melanogaster animal model to study the effects of early-life exercise training (ELET) on the aging heart and lifespan. We found in flies that age-induced arrhythmias are conserved across different genetic backgrounds. The fat body is the primary source of circulating lipoproteins in flies. Inhibition of fat body apoLpp (the flies apoB homolog) demonstrated that low expression of apoLpp reduced the development of arrhythmias in aged flies but did not affect average lifespan. At the same time, ELET can also reduce the expression of apoLpp mRNA in aged flies and have a protective effect on the heart, which is similar to the inhibition of apoLpp mRNA. Although treatment of apoLppRNAi and ELET alone had no significant effect on lifespan, the combination of apoLppRNAi and ELET extended the average lifespan of flies. Therefore, we conclude that apoLppRNAi and ELET are sufficient to resist age-induced arrhythmias, which may be related to the decreased expression of apoLpp mRNA, and that apoLppRNAi and ELET have a combined effect on prolonging the average lifespan.

The production of bio-chemicals requires the use of microbial strains with efficient substrate conversion and excellent environmental robustness, such as Bacillus coagulans spp. So far the genomes of about 50 strains have been sequenced. Herein, we report a comparative genomic analysis of nine strains on the full repertoire of CAZymes, secretion systems, and resistance mechanisms to environmental challenges. Moreover, B. coagulans Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR) immune system along with CRISPR-associated Cas) genes, was also analysed. Overall, this study expands our understanding of the strains genomic diversity of B. coagulans to fully exploit its potential in biotechnological applications.

In this present work, we are reporting a novel route for the synthesis of the tetracyclic ring systems, which is a common core of crinipellin via oxidative dearomatization, cycloaddition and oxa- di-pi-methane rearrangement. We considered to exploring a route to tetracyclic core (1e) of Crinipellin and tricyclic core (1g) of Allicaol B through intermolecular diels alder reaction and photochemically 1,2 acyl shift. Moreover, docking study of compound 13 and 16has been investigated against AcrB multidrug efflux pump of Escherichia coli (PDB ID: 1T9U), main protease of SARS COV-2 (PDB ID: 6W63), DNA gyrase of Streptococcus pneumonia (PDB ID: 4Z2C), human estrogen receptor alpha (PDB ID: 3ERT), human lanosterol 14-alpha-demethylase (CYP51)(PDB ID: 3JUS) and cyclooxygenase-2 (Prostaglandin Synthase-2) (PDB ID: 1CX2). The obtained results herein are important for the exploitation of the therapeutic potential of these derivatives as antimicrobial, antiviral, anticancer, antifungal or anti-inflammatory agents.

Multiple sclerosis is an autoimmune disorder where both T cells and B cells are implicated in pathology. However, it remains unclear how these two distinct populations cooperate to drive disease. There is ample evidence from studies in both MS patients and mouse models that Th17, B cells, and follicular T helper (TFH) cells contribute to disease. This review article describes the literature that identifies mechanisms by which Th17, TFH, and B cells cooperatively drive disease activity in MS and EAE. The curation of this literature has identified that CNS-infiltrating TFH cells act with TH17 cell to contribute to an inflammatory B cell response in neuroinflammation. This demonstrates that TFH cells and their products are promising targets for therapies in MS.

HepG2 cells reconstituted with Hepatitis B virus (HBV) entry receptor sodium taurocholate co-transporting polypeptide (NTCP) are widely used as a convenient in vitro cell culture infection model for HBV replication studies. As such, it is pertinent that HBV infectivity is maintained at steady-state levels for accurate interpretation of in vitro data. However, variations in HBV infection efficiency due to imbalanced NTCP expression levels in the HepG2 cell line may affect experimental results. In this study, we performed single cell cloning of HepG2-NTCP-A3 parental cells via limiting dilution and obtained multiple subclones with increased permissiveness to HBV. Specifically, one subclone (HepG2-NTCP-A3/C2) yielded more than 4-fold higher HBV infection compared to the HepG2-NTCP-A3 parental clone. In addition, though HBV infectivity was universally reduced in the absence of polyethylene glycol (PEG), subclone C2 maintained relatively greater permissiveness under PEG-free conditions, suggesting the functional heterogeneity within parental HepG2-NTCP-A3 may be exploitable in developing a PEG-free HBV infection model. The increased viral production correlated with increased intracellular viral antigen expression as evidenced through HBcAg immunofluorescence staining. Further, these subclones were found to express different levels of NTCP, albeit with no remarkable morphology or cell growth differences. In conclusion, we isolated subclones of HepG2-NTCP-A3 which support efficient HBV production and thus provide an improved in vitro HBV infection model.

Type 2 Diabetes Mellitus (T2DM) is one of the most common metabolic disorders, with a major involvement of oxidative stress in its onset and progression. Pioglitazone (Pio) is an antidiabetic drug which primarily works by reducing insulin resistance while Curcumin (Cur) is powerful antioxidant with o important hypoglycemic effect, also. The both drugs are associated with several drawbacks, such as reduced bioavailability, a short half-life time (Pio) as well as instability and poor water solubility (Cur), which limit their therapeutic use. In order to overcome these disadvantages, a new co-delivery (Pio, Cur) nanosystem based chitosan (CS) (CS-Pio-Cur NPs), was developed, and characterized in reference with simple nanosystems (CS-Pio NPs, CS-Cur NPs). The developed CS-based NPs (CS-Pio-Cur NPs, CS-Pio NPs, CS-Cur NPs) were physico-chemical characterized in terms of particle size (PS), entrapment efficiency (EF%) and loading capacity (LC%). The CS-Pio-Cur NPs proved increased or similar values of EE (88.95% ± 7.79 for Cur; 94.83% ± 9.89 for Pio) and LC% (24.25 % ± 1.62 for Cur; 3.5% ± 0.98 for Pio), in reference with simple nanosystems, CS-Cur NPs (EE = 82.46% ± 1.74; LC = 20.34% ± 0.94) and CS-Pio NPs) (EE = 96.31% ± 0.68; LC = 4.11% ± 0.47), respectively. The identification of APIs (Cur, Pio) loaded into CS matrix was performed using FR-IR spectroscopy and for simultaneously quantification of APIs (Cur, Pio) released from CS-Pio-Cur NPs, a HLPC method was developed and validated. Based on release study performed in different simulated fluids (SGF, SIF, SCF) it can be appreciated that developed CS-APIs NPs have favorable pharmacokinetic profile with good release in gastrointestinal tract.

The COVID-19 pandemic and tuberculosis have epidemiological similarities, being transmitted airborne, favored by direct contact, crowded environments and vulnerable biological status. We performed a retrospective study of 45 cases of pulmonary tuberculosis associated with COVID-19 (TB+COV+) compared to 45 cases with tuberculous monoinfection (TB+COV-), hospitalized during 2021-2022. The demographic characteristics were similar in the two groups, predominating men, a median age of 51 years, living in rural areas, medium level of education and smoking. Common symptoms of the two groups were cough, weight loss, profuse sweating, loss of appetite and hemoptysis, while fever, headache, myo-arthralgias and digestive symptoms characterized the TB+COV+ forms. The scores of radiological lesions in the TB+COV+ compared to TB+COV- group were significantly higher and persistent, revealing more frequent bilateral extensive lung lesions. There were no significant differences in the biological parameters between the two groups. Mortality was 2.2%, regardless of the association of COVID-19. The frequency of infections with Clostridioides difficile was higher in TB+COV+ cases. In conclusion, the co-infection of COVID-19 had an impact on the clinical and biological expression of tuberculosis diagnosed in a pandemic context.

The amalgamation of mineral and targeted bacterial preparations represents a new generation of agricultural technology. Inoculation with combined preparations of microorganisms is more effective than inoculation with a single microorganism in stimulating plant growth by providing a more balanced diet for various crops. In this work, the effect of inoculation of 20 consortium variants on the yield indicators of three crops (wheat, buckwheat, corn) and the soil microbiome in the open field was investigated. The soil microbiome was defined by 16S rRNA sequences through NGS. Species richness of the soil microbial community (alpha diversity) was similar for all studied samples. Beta-diversity analysis revealed that the microbial diversity of three soil samples (C.bw, F.bw and Soil.bw) differed significantly from all others. At the phylum level, the number of Acidobacteriota and Firmicutes in these samples was increased. For the combination “Consortium C (Rothia endophytic GMG9 and Azotobacter chroococcum GMG39) - buckwheat”, a systemic positive improvement in all growth and yield indicators was observed. The soil of the site where buckwheat grew, inoculated by Consortium C, contained significantly more available phosphorus than all other soil samples. Such results can be explained both by the direct action of a consortium of phosphate-immobilizing and nitrogen-fixing bacteria and to acidification of the medium due to an increase in phylum Acidobacteriota bacteria in the soil.

This paper presents a novel cheminformatics approach for the design and synthesis of hydroxyapatite/collagen nanocomposites, which have potential biomedical applications in tissue engineering, drug delivery, orthopedic and dental implants. The nanocomposites are synthesized by the co-precipitation method with different ratios of hydroxyapatite and collagen, and their mechanical, biological, and degradation properties are analyzed using various experimental and computational techniques, such as attenuated total reflection Fourier-transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, scanning electron microscopy with energy-dispersive X-ray spectroscopy, and molecular simulation. The antimicrobial activity of the nanocomposites is evaluated in vitro against several bacterial and fungal strains, demonstrating their medical potential. Additionally, in silico analyses are performed to predict the absorption, distribution, metabolism, and excretion properties and the bioavailability of the collagen samples. This work opens new avenues for the development of novel biomaterials using cheminformatics tools and methods, which can facilitate the optimization of the design and synthesis parameters, as well as the prediction of the biological outcomes. Future research directions include the investigation of the biocompatibility and bioactivity of the nanocomposites in vivo, as well as the exploration of other applications and functionalities of these nanocomposites.

Recently, there has been a lot of interest in the phenolics of pomegranate peels because of their health-promoting effects. The incorporation of encapsulated phenolic extracts in functional foods, beverages, and dietary supplements can enhance their nutritional and health benefits. This paper aims to provide an overview of the encapsulation of pomegranate peel phenolic extract by co-crystallization, focusing on the properties of the encapsulated extract. Pomegranate peel extract encapsulated in sucrose by co-crystallization at conditions determined in our previous work is characterized by evaluating its properties; moisture content, bulk density, solubility, hygroscopicity, color, degree of encapsulation by thermograms, crystallinity by X-ray scattering, microstructure by scanning electron microscope, and storage stability in terms of total phenolic content and antioxidant activity. The co-crystallized powder had a low moisture content (0.59%) and hygroscopicity (0.011%) and a high bulk density (0.803 g/cm3) and solubility (61 s). Its total phenolic content decreased by only 0.56% after storage at 60oC for 45 days, whereas its antioxidant activity was maintained at levels higher than 84%. The differential scanning calorimetry and the X-ray scattering techniques proved the successful encapsulation in the sucrose matrix and the fact that the extract remained liquid inside the porosity of the sucrose crystals.

This paper presents a bibliometric analysis of highly cited papers published in the journal Sustainability between 2009 and 2023. The aim is to identify influential countries, authors, and papers, as well as patterns in authorship and citation trends. The analysis focuses on frequently cited sources, the most cited research papers and references within the journal, and trends in author keywords. The analysis shows that Sustainability is a leading publication in sustainability research, with an annual growth rate of 53.57%. The selected papers, published between 2013 and 2022, have an average age of 2.11 years and an average of 88.12 citations each. The study highlights the most influential countries in sustainability research published in Sustainability, with China leading, followed by the United States and Germany. The most prolific authors are from China, Spain, and Italy. Interdisciplinary collaboration is essential to address complex sustainability challenges, as shown in the papers published in Sustainability. The study emphasizes the importance of staying informed about emerging trends and research directions in the field of sustainability published in this journal Sustainability. It underscores the significance of fostering international collaborations and partnerships to address complex sustainability challenges facing our world today, as evidenced by the papers published in Sustainability. Overall, this bibliometric analysis provides valuable insights into the current state of sustainability research published in Sustainability and its implications for policy and practice. It highlights key areas for future research and underscores the need for interdisciplinary collaboration to address complex sustainability challenges, as demonstrated by the papers published in Sustainability. These findings have important implications for policymakers, researchers, and practitioners interested in promoting sustainable development in the field of sustainability., as published in Sustainability.

Introduction: Increasing cannabis legalization raises concerns that tobacco use, frequently used with cannabis, will also increase. This study investigated the association between legal status of cannabis in place of residence and prevalence of cannabis and tobacco co-use, simultaneous use, and mixing by comparing the prevalence among adults in Canada (prior to cannabis legalization) vs. adults in US states that had legalized recreational cannabis vs. US states that had not as of September 2018. Methods: Data were drawn from the 2018 International Cannabis Policy Study, conducted with respondents aged 16-65 in Canada and the US recruited from non-probability consumer panels. Differences in the prevalence of co-use, simultaneous use, and mixing between tobacco and different cannabis products were examined using logistic regression models by legal status of place of residence among past 12-month cannabis consumers (N=6744). Results: Co-use and simultaneous use in the past 12 months were most common among respondents in US legal states. Among cannabis consumers, co-use and simultaneous use were less common in US legal states, while mixing was less frequent in US states with both legal and illegal cannabis compared to Canada. Use of edibles was associated with lower odds of all three outcomes, while smoking dried herb or hash was associated with higher odds. Conclusions: The proportion of cannabis consumers who used tobacco was lower in legal jurisdictions despite higher prevalence of cannabis use. Edible use was inversely associated with co-use suggesting that edible use does not appear to be associated with increased tobacco use.

As a typical form of value co-creation, crowdsourcing has been increasingly applied by firms to generate business value. By engaging a crowd, a platform, and other stakeholders, a crowdsourcer can foster the co-creation of a portfolio of value for diverse stakeholders. In analyzing the value co-creation in crowdsourcing, we propose a framework by combining the theories and frameworks in value co-creation and crowdsourcing. The framework examines the key stakeholders, joint purpose, engaged value co-creation processes, contributions, bidirectional relationships of the engagement, and perceived value, exhibiting a holistic view of the value co-creation in a crowdsourcing project. Results of the analysis reveal the business performance of the crowdsourcing project and identify areas of improvement regarding business sustainability. This is a major theoretical contribution of this study. The research design applied a case study approach to empirically investigate a crowdsourcing project. Both the theoretical and practical implications are discussed.

This pot-based study investigated the influence of co-composted wood-derived biochar on lettuce growth performance under salinity and drought stress conditions. Biochar of two particle sizes; > 2 mm and < 1 mm were co-composted with the mixture (1:1 ratio of dry weight) of cow and poultry manures. Co-composted biochars were applied at 5% and 7% rates in soil. Control treatments included the amendment of mixture of biochar with manure in soil. Pots were subjected to slight drought (48-55% water filled pore space (WFPS) of soil) and non-drought conditions (60% WFPS) and under 0 and 1.3 dS m-1 salinity. Results revealed that plants growth performance was significantly better under treatments of co-composted biochar and no salt stress conditions, than when mixture of biochar and manure was applied to soil as non-composted fertilizer. Under no stress condition, small particle-sized co-composted biochar increased root biomass by 786.2% than the large particle-sized co-composted biochar at same application rate. As compared to large-sized co-composted biochar, small sized co-composted biochar at high application rates increased root biomass by 167 – 245% but not leaf biomass under both stress conditions. Small particle-sized co-composted biochar amendment also increased the phosphorus use efficiency (PUE) of lettuce leaves than large particle-sized co-composted biochar under no stress condition. The amendment of small-sized co-composted biochar also increased significantly the concentration of Olsen phosphorus in soil than the amendment of large-particle-sized co-composted biochar. In conclusion, amendment of small particle-sized co-composted biochar has the potential of attenuating salinity and drought stress in lettuce and promoting P cycling in soil.

Applications in high-performance computing (HPC) may not use all available computational resources, leaving some of them underutilized. By co-scheduling, i.e. running more than one application on the same computational node, it is possible to improve resource utilization and overall throughput. Some applications may have conflicting requirements on resources and co-scheduling may cause performance degradation, so it is important to take it into account in scheduling decisions. In this paper, we formalized co-scheduling problem and proposed multiple scheduling strategies to solve it: an optimal strategy, an online strategy and heuristic strategies. These strategies vary in terms of the optimality of the solution they produce and a priori information about the system they require. We showed theoretically that the online strategy provides schedules with a competitive ratio that has a constant upper limit. This allowed us to solve the co-scheduling problem using heuristic strategies that approximate this online strategy. Numerical simulations showed how heuristic strategies compare to the optimal strategy for different input systems. We proposed a method for measuring input parameters of the model in practice and evaluated this method on HPC benchmark applications. We showed high accuracy of measurement method, which allows to apply proposed scheduling strategies in scheduler implementation.

The social distancing as a response to COVID 19 pandemic has led to the exceptional reductions of daily routine people activities and vehicle uses mainly in city. This same situation was also experienced by several busy, large, and populous cities in Southeast Asia (SA) countries. Correspondingly, this study aimed to test the hypothesis that the social distancing implementation period has increased the air quality in the term of carbon monoxide (CO) emission reduction as drawn from Jakarta city as an example of the one of populated cities in SA region. The CO was measured in parts per billions (ppb) and monitored on the daily basis employing remote sensor platform. The monitor periods were started from January, February, March, and April 2020 with 10 measurement days for each month. The social distancing was implemented from mid of March to the recent April. The CO measurement data were statistically tested to justify the significant effects of social distancing on the CO levels. Based on the CO data analysis, the order of CO mean by months is February > January > March > April. The CO levels for January, February, March, and April were 87.46 ppb (95%CI: 83.54-91.37), 88.20 ppb (95%CI: 81.65-94.74), 86.38 (95%CI: 81.06-91.69), and 78.68 (95%CI: 74.03-83.32) respectively. This study also find significant difference (p<0.05) of CO levels especially in April when social distancing has been implemented. Hence, these findings illustrate the potential air pollutant reduction gained from implementing social distancing as can be seen in April.

Degussa P25 is a benchmark form of TiO₂ used worldwide in photocatalysis studies. Currently no such benchmark exists for co-catalysts, which are essential for many photocatalytic reactions. Here, we present the preparation of Pt nanocluster co-catalysts on TiO₂ using an unmodified commercial source and equipment that is commonly available. Transmission electron microscopy reveals that the procedure produces TiO₂ decorated with Pt atom and nanoclusters (1-5 atoms). Optical reflectance and X-ray diffraction measurements show that the procedure does not affect the TiO₂ polymorph or UV-Vis absorbance. Gas phase photocatalytic splitting of heavy water (D₂O) shows that the Pt nanocluster decorated TiO₂ outperforms Pt nanoparticle (produced by photodeposition) decorated TiO₂ in D₂ production. Pt nanoclusters, produced directly from a commercial source, with high co-catalyst activity are prime candidates to be used in benchmark photocatalytic reactions.

In order to understand the effect of Pb-CuI co-doping on the thermoelectric performance of Bi₂Te₃, n-type Bi₂Te₃ co-doped with x at% CuI and 1/2x at% Pb (x = 0, 0.01, 0.03, 0.05, 0.07, and 0.10) were prepared via high temperature solid state reaction and consolidated using spark plasma sintering. Electron and thermal transport properties, i.e., electrical conductivity, carrier concentration, Hall mobility, Seebeck coefficient, and thermal conductivity, of CuI-Pb co-doped Bi₂Te₃ were measured in the temperature range from 300 K to 523 K and compared to corresponding x% of CuI-doped Bi₂Te₃ and undoped Bi₂Te₃. The addition of a small amount of Pb significantly decreased the carrier concentration, which could be attributed to the holes from Pb atoms, thus the CuI-Pb co-doped samples show a lower electrical conductivity and a higher Seebeck coefficient compared to CuI-doped samples with similar x values. The incorporation of Pb into CuI-doped Bi₂Te₃ rarely changed the power factor because of the trade-off relationship between the electrical conductivity and the Seebeck coefficient. The total thermal conductivity(κ_tot) of co-doped samples (κ_tot ~1.4 W/m∙K at 300 K) is slightly lower than that of 1% CuI-doped Bi₂Te₃ (κ_tot~1.5 W/m∙K at 300 K) and undoped Bi₂Te₃ (κ_tot ~1.6 W/m∙K at 300 K) due to the alloy scattering. The 1% CuI-Pb co-doped Bi₂Te₃ sample shows the highest ZT value of 0.96 at 370 K. All data on electrical and thermal transport properties suggest that the thermoelectric properties of Bi₂Te₃ and its operating temperature can be controlled by co-doping.

Although lymphoma is the most frequent malignancy in common variable immunodeficiency (CVID), solid tumors, especially under influence of oncogenic viruses, are not considered. Furthermore, in vitro genetic studies and cell cultures are not adequate for immune system and HBV interaction. We adopted previously introduced clinical model of host-virus interaction (i.e. infectious process in immunodeficiency) for analysis of B cells and specific IgG role (observational study of a CVID patient who received intravenous immunoglobulin (IVIG)) Suddenly, the patient deteriorated with positive result of HBs, HBV-DNA (369x106copies). In spite of lamivudine therapy and IVIG escalation (from 0.3 to 0.4g/kg), CT showed 11cm intrahepatic tumor (hepatocellular carcinoma). Anti-HBs had been positive in time-lapse analysis (range 111-220 IU/ml). Replacement therapy intensification was complicated by immune complex disease with renal failure. The fulminant HCC in CVID and the development of the tumor as the first sign is interesting. Unfortunately, treatment with hepatitis B immune globulins (HBIG) plays a major role in posttransplant maintenance therapy. Anti-HBs substitution has not been proven to be effective, oncoprotective nor safe. Therefore, immunosuppression in HBV-infected recipients should be carefully minimized, patient selection more precise with the exclusion of HBV-positive donors. Our clinical model show HCC pathway with important humoral host factors, contrary to epidemiological/cohort studies highlighting risk factors only (e.g. chronic hepatitis). Lack of cell cooperation, B cell deficiency observed in CVID plays a crucial role in high HBV replication, especially in carcinogenesis.