Real data obtained from ship in operation are processed and analyzed in this paper. The intention was to provide software which would predict ship’s fuel consumption in some future time instant. It is showed that it is possible to develop such software based on numeric fitting of known data. In order to check how well the prediction of future fuel consumption is, we used only the first half of data for obtaining prediction curve. The second part of data was used to compare different prediction curves goodness. Hence, the presented research used actually a “real future data” and forecasted future data, which are used to numerically evaluate goodness of prediction. The research is of interest for companies logistics, to provide adequate fuel for fleet when and where actually needed. It is concluded that there are several prediction functions which satisfy used statistical quality measures.

Due to growing environmental concerns and stringent emissions regulations, optimizing the fuel consumption of marine propulsion systems is crucial. This work deals with the potential in an LNG ship propulsion system to reduce fuel consumption through controlled load distribution between engines in Dual Fuel Diesel Electric (DFDE) plant. Based on cyclical data acquisitioning measured on board and using an optimization model, the study evaluates different load distribution strategies between set up according to the optimization model results and automatic (equal) operation to determine their effectiveness in improving fuel efficiency. The analysis includes scenarios with different fuel types, including LNG, MDO and HFO, at different engine loads. The results indicate that load distribution adjustment based on the optimization model results significantly improves fuel efficiency compared to conventional methods of uniform load distribution controlled by power management systems almost in all load intervals. This research contributes to the maritime industry by demonstrating that strategic load management can achieve significant fuel savings and reduce environmental impact, which is in line with global sustainability goals. This work not only provides a framework for the implementation of more efficient energy management systems on LNG vessels, but also sets a benchmark for future innovations in maritime energy optimization as well as in the view of exhaust emission reduction.

The analysis focuses on the intensity of energy consumption in the transportation sector, of the oil-rich country, Iran. The study emphasizes the importance of reducing energy consumption in transportation and identifies factors that affect energy efficiency. The research explores the impact of population growth, clean fuels, energy prices, and investment in energy efficiency in the transport sector. Using data from 1979 to 2011, the study estimates a model with the Autoregressive Distributed Lag model and emphasizes the significance of clean and renewable energies in reducing energy intensity. It also discusses the theoretical background, energy intensity factors, production technology, and the role of clean energy sources. The model framework includes variables like energy intensity index, relative energy price, number of cars, investment ratio, and clean energy production. The findings suggest an increasing trend in energy consumption in the transportation sector, highlighting the importance of identifying drivers that affect energy consumption in the sector.

In recent years, with the increasing impact of climate change, achieving the "dual carbon" goal has become increasingly urgent. Fossil fuel consumption is one of the main sources of carbon emissions and is closely related to economic development. Therefore, it is necessary to decouple economic growth from fossil fuel consumption as soon as possible. However, the small sample defect in fossil energy consumption panel data has caused great difficulties for machine learning algorithms. To address this defect, this study uses TimeGAN for data augmentation and compares the performance of six regression analysis methods (XGBoost, CatBoost, LGBM, KNN, linear regression, decision tree) in predicting fossil energy consumption. In addition, feature importance and SHAP are used simultaneously to explore the main driving factors of fossil energy consumption. The research results show that the decoupling index of most provinces fluctuated relatively little from 2011 to 2018. Compared to other machine learning algorithms, XGBoost and CatBoost perform better in predicting fossil energy consumption. Finally, based on two interpretable analysis methods, we found that population has the most significant impact on fossil energy consumption, followed by GDP, and urbanization rate is the least important. The research results provide important information for formulating energy sustainable development strategies and further discuss energy-saving solutions based on data methods.

The U.S. Energy Information Administration (EIA) provides crucial data on monthly and annual fuel consumption for electricity generation. This data covers significant fuels such as coal, petroleum liquids, petroleum coke, and natural gas. Fuel consumption patterns are highly dynamic, influenced by diverse factors. Understanding these fluctuations is essential for effective energy planning and decision-making. This study outlines a comprehensive analysis of fuel consumption trends in electricity generation. Utilizing advanced statistical methods, including time series analysis and autocorrelation, our objective is to uncover intricate patterns and dependencies within the data. This paper aims to forecast fuel consumption trend for electricity generation using data from 2015 to 2022. Several time-series forecasting models, including all four benchmark methods (Mean, Naïve, Drift, and seasonal Naïve), Seasonal and Trend Decomposition using Loess (STL), Exponential Smoothing (ETS), and Autoregressive Integrated Moving Average (ARIMA) methods, have been applied. The best-performing models are determined based on Root Mean Squared Error (RMSE) values. For Natural Gas (NG) consumption, the ETS model achieves the lowest RMSE of 20,687.46. STL demonstrates the best performance for coal consumption with an RMSE of 5,936.203. The seasonal Naïve (SNaïve) model outperforms others for petroleum coke forecasting, yielding an RMSE of 99.49. Surprisingly, the Mean method has the lowest RMSE of 287.34 for petroleum liquids, but the ARIMA model is reliable for its ability to capture complex patterns. Residual plots are analyzed to assess the models' performance against statistical parameters. Accurate fuel consumption forecasting is very important for effective energy planning and policymaking. The findings from the study help policymakers strategically allocate resources, plan infrastructure development and support economic growth.

As the world grapples with the COVID-19 pandemic, there has been a sudden and abrupt change in global energy landscape. Traditional fossil fuels that serve as the linchpin of the modern civilization have found their consumption rapidly fell across the most categories due to strict lockdown and stringent measures that have been adopted to suppress the disease. These changes consequently steered various environmental benefits across the world in recent time. The present article is an attempt to investigate these environmental benefits and reversals that have been materialized in this unfolding situation due to reduced consumption of fossil fuels. Life cycle assessment tool has been used hereby to evaluate nine environmental impacts and one energy based impact. These impacts include: ozone formation (terrestrial ecosystems), terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial ecotoxicity, freshwater ecotoxicity, marine ecotoxicity, land use, mineral resources scarcity and cumulative exergy demand. Outcomes from the study demonstrate that COVID-19 has delivered impressive changes in global environment and life cycle exergy demand with about 11-25% curtailment in all above-mentioned impacts in 2020 in comparison to their corresponding readings in 2019.

Traffic source emissions inventories for the rapidly growing West African urban cities are necessary for better local characterization of vehicle emissions released into these cities atmosphere. This study based on local field campaign in a representative site of anthropogenic activities over West African cities such as Yopougon (Abidjan, Côte d'Ivoire) during 2016, provided useful information on vehicle type and age, traveling time, fuel type and amount for fuel consumption estimation. Also, high traffic flow of personal car were recorded on highway, boulevard and backstreet whereas high flows of intra-communal sedan taxi are recorded on main and secondary roads. In addition, the highest daily fuel consumption value of 56 L.day^-1 was recorded in heavy vehicle while the lowest value of 15 L.day^-1 is recorded for personal car using gasoline. This study will be useful for the improvement of uncertainties related to the different databases used to estimate inventories emissions either national or international reports. This work provides useful information for future studies on urban air quality, climate and health impacts assessment in African cities. It may also be useful for policy makers to support implementation of emission reduction policy in West African cities.

Private vehicle travel is the most basic mode of transportation, and the effective control of the real-world fuel consumption rate of light-duty vehicles plays a vital role in promoting sustainable economic development as well as achieving a green low-carbon society. Therefore, the impact factors of individual carbon emission must be elucidated. This study builds five different models to estimate real-world fuel consumption rate of light-duty vehicles in China. The results reveal that the Light Gradient Boosting Machine (LightGBM) model performs better than the linear regression, Naïve Bayes regression, Neural Network regression, and Decision Tree regression models, with mean absolute error of 0.911 L/100 km, mean absolute percentage error of 10.4%, mean square error of 1.536, and R squared (R2) of 0.642. This study also assesses a large number of factors, from which three most important factors are extracted, namely, reference fuel consumption rate value, engine power and light-duty vehicle brand. Furthermore, a comparative analysis reveals that the vehicle factors with greater impact on real-world fuel consumption rate are vehicle brand, engine power, and engine displacement. Average air pressure, average temperature, and sunshine time are the three most important climate factors.

The building sector of most tropical countries still use predominantly primary biomass as the principal fuel. This has adverse effects like CO2 emission and deforestation and is associated with issues like poverty, ill-health, and low standard of living. Therefore, energy policies try to improve on the efficiency of firewood and charcoal end-use technologies, to palliate the negative effects. In this research, the global change assessment model (GCAM) is used, to investigate the impact of efficiency improvement on the energy consumption pattern of the building sector of developing countries. The aim of the study is to provide empirical data that would better inform policymakers on the effects of modernizing these primary fuels. The study developed three scenarios with different levels of efficiency improvements. The results show that efficiency improvement rather increases primary biomass consumption and CO2 emission. However, there is a fall in the consumption of traditional biomass in the second half of the modelling period. The increase in biomass-based fuels consumption was seen to be linked to their affordability. Therefore, policymakers need not only elaborate policies that improve biomass efficiency, but also introduce and motivate other clean cooking fuels like butane, biogas, and electricity.

The COVID-19 epidemic and the measures adopted to contain it have had a significant impact on energy patterns throughout the world. The pandemic and movement restrictions led to unpredictable fluctuations in power systems demand and the fuel price for a delayed period. Monkeypox, another viral disease, appeared during the post-COVID period. It is assumed that the outbreak of monkeypox is unlikely due to the implication of preventive measures experienced by COVID-19. At the same time, the probability of an epidemic cannot be blindly overlooked. This paper aims to examine and analyze historical data to look at how much petroleum fuel was used for generating power and how the price of petroleum fuel changed over seven years, from January 2016 to August 2022. This period covers the time before the COVID-19 pandemic, during the pandemic, and after the pandemic. Several time-series forecasting models, including all four benchmark methods (Mean, Naïve, Drift, and Snaïve), Seasonal and Trend decomposition using Loess (STL), Exponential Smoothing (ETS), and Autoregressive Integrated Moving Average (ARIMA) methods have been applied for both fuel consumption and price prediction. The best forecasting method for fuel price and consumption has been identified among these methods. The paper also utilizes the ARIMAX model by incorporating multiple exogenous variables, such as monthly mean temperature, mean fuel price, and mileage of vehicles traveling during a certain period of pandemic lock-down. It will assist in capturing the non-smooth and stochastic pattern of fuel consumption and price due to the pandemic by separating the seasonal influence and thus provide a prediction of the consumption pattern in the event of any future pandemic.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

By 2020, over 100 countries expanded electric and plug-in hybrid electric vehicle (EV/PHEV) technologies, with global sales surpassing 7 million units. Governments are adopting cleaner vehicle technologies due to proven environmental and health implications of internal combustion engine vehicles (ICEVs), evidenced by the recent COP26 meeting. This article proposes an agent-based model of vehicle activity as a tool for quantifying energy consumption by simulating a fleet of EV/PHEVs within an urban street network at various spatio-temporal resolutions. Driver behaviour plays a significant role in fuel consumption, thus, simulating various levels of individual behaviour enhancing heterogeneity should provide more accurate results of potential energy demand in cities. The study found that 1) energy consumption is lowest when speed limit adherence increases (low variance in behaviour) and is highest when acceleration/deceleration patterns vary (high variance in behaviour) and 2) on average, for tested vehicles, EV/PHEVs were £116.33 cheaper to run than ICEVs across all experiment conditions. The difference in the average fuel costs (electricity and petrol) shrinks at the vehicle level as driver behaviour is less varied (more homogeneous). This research should allow policymakers to quantify the demand for energy and subsequent fuel costs in cities.

Today, reducing vehicle energy consumption is a crucial topic. For electric vehicles, reducing energy consumption is essential to address some of the most critical issues associated with this type of vehicle, such as the limited range of electric powertrains and the long battery recharging times. To lower the environmental impact during the vehicle’s use phase and reduce energy consumption, vehicle mass reduction (lightweighting) is an effective strategy. The objective of this work is to analyze the vehicle parameters that influence lightweighting outcomes on a real driving cycle, representative of the home-to-work travel in the northern Italy. In particular, a previous work carried out on standard driving cycles is repeated, in order to observe whether it is possible to draw the same conclusions regarding the variability of the lightweighting outcome. This study was conducted using two opposite vehicle models, a compact car and an N1 vehicle, simulated through a well-established vehicle simulation tool for energy consumption estimation. The study reveals that even for the real driving cycle, as for the WLTC and US06 standards, the parameters that most influence the outcome of the lightening are rolling resistance, the characteristics of the battery pack, the aerodynamic coefficients and the efficiency of the transmission. Finally, the standard cycle that best fits with the real one considered in this study is the Artemis Urban Cycle.

This study investigates the effect of different variables in the optimization of a hybrid air charging systems for marine diesel engines, exploring the potential for energy recovery and assistance using electric machines. The optimization parameters include turbine speed, compressor power, start of injection, turbomachine size, and valve timing. At low engine speeds, the larger improvements come from increasing compressor power, which increases air-to-fuel ratio compared with the baseline turbocharging. As free-floating turbocharged engines are known to have low air-to-fuel ratio at low engine speeds, the relative improvement of the hybrid architecture is large at low engine speeds, being near to 10% less BSFC. At high engine speeds, the largest influence is marked by the SOI, an early injection obtains a faster combustion, which improves gross efficiency. However, the relative improvement compared with baseline turbocharger is less than 1% at high engine speeds. Due to the distribution of relative improvement of BSFC, this architecture has a deeper impact on fuel consumption in vessel operating cycles that focus on low engine speeds and loads, such as those of tugboats.

A critical review of recent work on fuel lubricant interactions is undertaken. The work focusses on liquid fuels used in diesel and gasoline vehicles. The amount of fuel that contaminates the lubricant depends on driving conditions, engine design, fuel type and lubricant type. When fuel contaminates a lubricant, the viscosity of the lubricant will change (it will usually decrease), the sump oil level may increase, there may be a tendency for more sludge formation, there may be an impact on friction and wear, and low speed pre-ignition could occur. The increased use of biofuels (particularly biodiesel) may require a reduction in oil drain intervals, and fuel borne additives could contaminate the lubricant. The move to active regeneration of particulate filters by delayed fuel post-injection and the move to hybrid electric vehicles, and vehicles equipped with stop-start systems will lead to increased fuel dilution. This will be of more concern in diesel engines, since significant fuel dilution could still persist at sump oil temperatures in the range 100-150C (whereas in gasoline engines the more volatile gasoline fuel will have substantially evaporated at these temperatures). It is anticipated that more research into fuel lubricant interactions, particularly for diesel engines, will be needed in the near future.

Relying on Random Utility Theory (RUT) as the guiding mechanism for the Data Generating Process (DGP), this paper uses households consumption choices on cooking fuel, drinking water, and sanitation from the 2014 United States Agency for International Development's (USAID) Demographic and Health Survey (DHS) data on Burkina Faso, to characterize and investigate the inter-linkages between health consciousness and environmental consciousness, and their relationship with wealth in a low income country context. We achieve this by specifying sequentially three econometric modeling frameworks: the first one being independent binary probit (IBP) models to describe each choice process, followed by a fully parametric trivariate probit (FPTP) model to account for choice dependency, and finally by a semi-parametric trivariate probit (SPTP) model to further relax the linearity assumption. Based on the Akaike Information criteria (AIC) and the estimated Trivariate model correlation coefficients, the SPTP framework is found to be the best specification for describing the observed consumption behaviors. The results show that increased wealth level raises households health and environmental consciousness, while leaving the relative preference ordering over the elements in the household consumption basket unchanged.

Techniques and tools meant to aid fire management activities in the Cerrado, such as accurately determining fuel load and composition spatially and temporally, are pretty scarce. The need to have fuel information for more efficient management in a considerably heterogeneous, biodiverse, and fire-dependent environment makes a constant search for the improvement of the use of remote sensing techniques in determining fuel characteristics. This study presents the following objectives: (1) to assess the use of data from Landsat 8 OLI images to estimate the fine surface fuel load of the Cerrado during the dry season by adjusting multiple linear regression equations; (2) to estimate fuel load through Random Forest and k-Nearest Neighbor (k-NN) algorithms in comparison with re-gression analyses; and (3) to evaluate the importance of predictor variables from satellite images. Therefore, 64 sampling units were collected, and the pixel values associated with the field plots were extracted in a 3 x 3 pixel window surrounding the reference pixel. For the multiple linear regression analyses, the R² values ranged from 0.63 to 0.78, and the models fitted by the Random Forest al-gorithm ranged from 0.52 to 0.83, while those fitted by k-NN ranged from 0.30 to 0.68. Adopting the Random Forest algorithm resulted in improvements in the statistical metrics of evaluation of the fuel load estimates for Cerrado grassland relative to the multiple linear regression analyses.

Synthetic fuels play an important role in the defossilization of future aviation transport. To reduce the ecological impact of remote airports due to long range transportation of kerosene, a decentralized on-site-production of synthetic paraffinic kerosene is applicable, preferably as near-drop-in fuel or alternatively as blend. One possible solution for such a production of synthetic kerosene is the Power-to-Liquid process. The basic development of a simplified plant layout addressing the specific challenges of a decentralized kerosene production which differ from most current approaches for infrastructural well-connected regions is described. The decisive influence of the Fischer-Tropsch synthesis on the PtL process is shown by means of a steady-state reactor model which was developed in Python and serves as basis for further development of a modular environment able to represent entire process chains. The reactor model is based on reaction kinetics according current literature. The effects of adjustments of the main operation parameters on the reactor behavior are evaluated and the impacts on up- and downstream processes are described. The results prove the governing influence of the Fischer-Tropsch reactor on the PtL process and show its flexibility regarding the desired product fraction output, which makes it an appropriate solution for a decentralized kerosene production.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

The overexploitation of fossil fuels and their negative environmental impact has attracted the attention of researchers worldwide to propose alternatives to produce bioenergy. Microbial fuel cells (MFCs) systems are sustainable biotechnologies that use bacterial activity to break down organic matter while generating bioelectricity. MFCs have bioelectricity from domestic wastewater (DWW), municipal wastewater (MWW), and potato and fruit waste, reducing environmental contamination and decreasing energy consumption and treatment cost. This review focuses on the recent advancements regarding the designs and configurations, the operation mode of MFCs, and their capacity to produce bioelectricity (e.g., 2203 mW/m2) and fuels (i.e., H2: 438.7 mL/g and CH4: 358.7 mL/g, respectively). Besides, this review highlights practical applications, challenges, techno-economic, and life cycle assessments (LCA) of MFCs. Despite MFC's promising biotechnology, great efforts should be made to implement it in real-time and commercialization.

Computational methods are essential to support and advance nuclear technologies due to the hazards of handling and analysing highly radioactive materials such as spent nuclear fuel (SNF). However, many such methods, including those thatcan predict SNF compositions and decay heat parameters, require expensive, proprietary software, alongside significant programming experience and computational power for utilisation, severely limiting availability of data and hampering research throughput. Although some datasets are available, many are incomplete or only cover certain fuel systems for older reactor types. Research investigating new methods for SNF recycling, for example, requires compositional and decay heat data for fuel systems not covered by extant data, though analogous source data may be available. With this in mind, we have developed a simple, accessible, and flexible method for extrapolation of isotopic, elemental, and decayheat compositions for SNF at discharge and following decay storage before recycling, based on an extant dataset. This semi-empirical method uses physical and mathematical first principles and can be performed using software accessible to all researchers. This provides outputs accurate to within 1% of reference values interpolated within the range of available data for isotopic compositions, with sensible extrapolations at higher burnups beyond those reported, withoverall elemental outputs accurate to within 0.1%of expected totals. In this publication, we present the developmental methodology, some sample data, the present limitations, and options for future development and expansion of functionality.

Metal-supported fuel cells (MSCs) offer potential material cost and robustness advantage over anode supported cells (ASCs). Because of the very good thermal shock stability of such MSCs, these can be heated up very quickly. However the challenge co-firing of metal substrate and electrolyte stays still unsolved. The production of the core component, the tape casted metal substrate, with defined shrinkage resulting from modification of metal powders is presented in the paper. This approach leads to an adjustment of the shrinkage mismatch during sintering, between metal and ceramic components, and adjustment of target specifications like porosity, green density and layer thickness.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

The exposure of Mediterranean forests to large wildfires requires mechanisms to prevent and mitigate their negative effects on the territory and ecosystems. Fuel models synthesize the complexity and heterogeneity of forest fuels and allow understanding and modelling of fire behavior. However, it is sometimes challenging to define the fuel type in a structurally heterogeneous forest stand due to the mixture of characteristics from different types and limitations of qualitative field observation and passive and active airborne remote sensing. This can impact the performance of classification models that rely on in situ identification of fuel type as ground-truth, which can lead to a mistaken prediction of fuel types over larger areas in fire prediction models. In this study, a handheld mobile laser scanner (HMLS) system were used to assess its capability to define Prometheus fuel types in 43 forest plots in Aragón (NE Spain). The HMLS system captured the vertical and horizontal distribution of fuel at extremely high resolution to derive high-density three-dimensional point clouds (average: 63,148 points/m2) which were discretized into voxels of 0.05 m3. The total number of voxels in each 5 cm height stratum was calculated to quantify the fuel volume in each stratum, providing the vertical distribution of fuels (m3/m2) for each plot at centimetric scale. Additionally, fuel volume was computed for each Prometheus height stratum (0.60, 2, and 4 m) for each plot. The Prometheus fuel types were satisfactory identified for each plot, which was compared with the fuel type estimated in the field. This led to the modification of the ground-truth in 10 out of the 43 plots, with estimation errors between types 2–3, 5–6, and 6–7. These results demonstrate the ability of HMLS systems to capture fuel heterogeneity at centimetric scales for the definition of fuel types in Mediterranean forests, making them powerful tools for fuel mapping and fire modelling, and ultimately for improving wildfire prevention and forest management.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The disastrous 2017 fire season in Portugal lead to widespread recognition of the need for a paradigm shift in forest and fire management. We focused our study on Alvares, a parish in central Portugal which had 60% of its area burned in 2017, with a large record of historical. We evaluated how different fuel treatment strategies can reduce wildfire hazard in Alvares, through i) a fuel break network with different priorities and ii) random fuel treatments resulting from stand-level management intensification. To assess this, we developed a stochastic fire simulation system (FUNC-SIM) that integrates uncertainties in fuel distribution over the landscape. If the landscape remains unchanged, Alvares will have large burn probabilities in the north, northeast, and center-east areas of the parish that are very often associated with high fire line intensities. The different fuel treatment scenarios decreased burned area between 12.1-31.2%, resulting from 1%-4.6% increases in annual treatment area, and reduced 10%-40% the likelihood of wildfires larger than 5000 ha. On average, simulated burned area decreased 0.22% per each ha treated, and effectiveness decreased with increasing area treated. Overall, both fuel treatment strategies effectively reduced wildfire hazard and should be part of a larger, holistic and integrated plan to reduce the vulnerability of the Alvares parish to wildfires.

The use of hydrogen fuel cells as a mobile source of electricity might prove to be a keystone in future decarbonization of heavy duty road and marine transport. Due to complex interplay of various physicochemical processes in the fuel cells, further development of these devices will rely on concerted effort of researchers from various fields, e.g. chemistry, physics, electric and mechanical engineering. This results in knowledge gaps which are filled by the information, dispersed in wide range of literature, but rarely covered in a short and condensed form. To address this issue and with the aim of providing a concise and simple explanation of fuel cell operation, we propose a simple educational model of the most relevant processes in the fuel cell, aimed at proper description of causal relations. The derivation of model equations provides an intuitive understanding of electric potentials acting on protons on the microscopic level and relates this knowledge to the common terminology in fuel cell research community, such as catalyst electric overpotential and internal membrane resistance. The results of the model fit well with experimental data, indicating that a simple description, provided in the paper, is sufficient for intuitive understanding of fuel cell operation.

The study within the current research is focused on theoretical assessment of sustainable aviation fuels (SAF) obtained by blending traditional jet fuels Jet A and different liquids (biodiesel and alcohols) from analytical point of view. Within this paper in-depth analysis ofthe physical-chemical properties of Jet A fuel blended with different biodiesels and alcohols has been performed. Also within the blends Aeroshell 500 oil has been added (5% vol.) for ensuring the lubrication of the turbo engine. The blends consists of: Jet Aaviation fuel + biodieselfrom: palm oil, pork fat, sunflower oil and alcohols: methanol, ethanol and butanol. All the 6 liquids have been blended with Jet A in the following percentages: 10, 20 and 30%. Flash point, kinematic viscosity, density, freezing point, elemental analysis and FTIR analysis have been performed for all the liquids: Aeroshell 500, jet A, jet A + 10, 20, 30% biodiesel from waste palm oil, pork fat and waste sunflower oil, jet A + 10, 20, 30% methanol, ethanol and butanol, biodiesels and alcohols. The obtained results shows the influence of each of the blend’s components on the physical-chemical properties of the blends. Based on the physical-chemical analysis of the blends, conclusions on the behavior of the blends during burning and the gaseous pollutants resulting from the burning process can be drawn.

The increasing global demand for energy and the pressing challenge of environmental pollution necessitates a paradigm shift towards sustainable energy sources. Hydrogen, a viable renewable energy carrier, has the potential to substantially alleviate these concerns. This review offers a comprehensive exploration of the technologies imperative to the production and operation of fuel cell vehicles (FCVs), ranging from various fuel cell types, hydrogen storage methods, fueling station logistics, batteries in hydrogen vehicles, and the emerging influence of artificial intelligence and quantum computing. An analytical overview of global adoption patterns reveals significant geographical disparities, with the United States and South Korea at the forefront of FCV integration, primarily in the form of passenger cars, followed by buses and trucks. Asia emerges as the region with the highest proportion of FCVs. This paper also delves into the diverse challenges facing FCV implementation, shedding light on the essential role of continued investment in the evolution of sustainable transportation systems. Furthermore, it provides insights into the varying contributions of different companies in the field, demonstrating the collective effort required to advance this promising technology. The comprehensive exploration provided in this review aids in understanding the opportunities, challenges, and potential of hydrogen as an integral player in the future of sustainable transportation. The increasing need for energy carriers and the rise of environmental pollution have driven the exploration of renewable energy sources, with hydrogen being a promising option.

To increase the efficiency of fuel processor and HT-PEMFC (High Temperature-Proton Exchange Membrane Fuel Cell) combined system, it is essential to improve the efficiency of a fuel processor. In this research, the fuel processor was simulated by Aspen Hysys® simulator, and effect of the various operating conditions on the total efficiency was investigated. Thermal efficiency of the fuel processor increased as the temperature and S/C (Steam to carbon) ratio increased, and the efficiency was higher at the S/C ratio of 3 than at the S/C of 4 at the reformer temperature of 700 ℃ and higher. Under the selected operating conditions of the fuel processor, recycling of unreacted hydrogen from the anode off gas (AOG) of the HT-PEMFC improve the overall efficiency of the combined fuel processer and HT-PEMFC by a factor of 1.28. Operating conditions where the AOG supplied excessive heat than required for fuel processor operation were excluded. The high-efficiency operating conditions of the fuel cell system were proposed with the target of 5 kW of output as the capacity of the household HT-PEMFC.

In order to study the movement characteristics of fuel in the fuel tank during aircraft maneuvering, this paper conducts numerical simulations of a typical wing fuel tank using the finite point set method based on certain boundary conditions and excitation. The results show that the finite point set method can capture the complex phenomena of fuel free surface fluctuations, surging, rolling and breaking, as well as the change in center of gravity caused by fuel movement. Under aircraft acceleration and pitch angle excitation, fuel will generate sustained impact pressure on the fuel tank wall. The velocity attenuation of fuel flowing through the baffle communication hole is fast, and the flow resistance and energy dissipation of the communication hole buffer the impact of fuel on the fuel tank wall.

Fossil fuels and carbon origin resources are affecting our environment. Therefore, alternative energy sources have to be established to co-produce energy along with fossil fuels and carbon origin resources until it is the right time to replace them. Microbial Fuel Cell (MFC) is a promising technology in the field of energy production. Compared to the conventional power sources it is more efficient and not controlled by the Carnot cycle. Its high efficiencies, low noise, and less pollutant output could make it revolutionize in the power generation industry with a shift from centrally located generating stations and long-distance transmission lines to dispersed power generation at load sites. In this review, several characteristics of the MFC technology will be highlighted. First, a brief history of abiotic to biological fuel cells and subsequently, microbial fuel cells is presented. Second, the focus is then shifted to elements responsible for the making MFC working with efficiency. Setup of the MFC system for every element and their assembly is then introduced, followed by an explanation of the working machinery principle. Finally, microbial fuel cell designs and types of main configurations used are presented along with scalability of the technology for the proper application.

With growing regulations on ship emissions, specifically carbon dioxide and nitrogen oxides, this study emphasizes the critical need for improving the performance of existing ship diesel engines. Focusing on easily modifiable injection conditions within the fuel system, the research aims to enhance combustion characteristics for operational ships. The study provides a concise analysis of the combustion performance improvements achievable in the field. The study employed a range of calculation conditions, spanning from fuel injection pressures of 20 MPa to 160 MPa, injection timing from 15 degrees before top dead center (BTDC) to 5 degrees after top dead center (ATDC), and spray angles varying between 10 degrees and 50 degrees. A comprehensive analysis was conducted, focusing on fuel distribution behavior, combustion dynamics, carbon monoxide (CO) production and extinction, as well as nitrogen oxide (NO) production. This thorough examination aimed to provide insights into the complex interplay of these factors in order to optimize combustion performance in ship diesel engines. The analysis indicated that substantial unburned fuel occurred at injection pressures below 40 MPa and spray angles less than 20 degrees. This issue was significantly mitigated when injection pressures exceeded 80 MPa or a spray angle of 40 degrees was employed. High flame propagation speeds were observed at injection pressures over 80 MPa and injection timings before BTDC 10. Carbon monoxide emissions were notably low when injection pressures exceeded 80 MPa and a 40-degree spray angle was used. Nitrogen oxide emissions were minimized under conditions of injection pressure below 40 MPa, injection timing after BTDC 5 degrees, and a spray angle between 30 and 40 degrees. The study concludes that the most effective injection conditions for concurrently reducing fuel consumption, minimizing incomplete combustion products, and lowering nitrogen oxide emissions in the target engine are optimal when the injection pressure is set at 80 MPa, the injection timing is positioned at 5 degrees before top dead center (BTDC), and the spray angle is maintained at 40 degrees.

Prescriptions for fuels management are universally applied across forest types in British Columbia, Canada, to reduce fire behaviour potential in the wildland-urban interface. Fuel thinning treatments are assumed to reduce the potential for sustained ignition and crown fire initiation by reducing surface fuel loading. We hypothesized that these prescriptions are not appropriate for the coastal wet forests in the Whistler region of the province. Our study measured the efficacy of fuel thinning treatments in four stands located in the Whistler community forest. We examined several in-stand microclimate variables during snow melt in the spring and at the height of fire danger in late summer, at thinned and unthinned locations paired using GIS- analysis. We found that thinning increased the wildfire risk based on the differences between unthinned and thinned areas in the same forest stand.

This study proposes a redesign of asymmetric single-chamber microbial fuel cells (a-SCMFC) with the goal of optimizing energy production. The new approach is based on the introduction of an Intermediate Microfluidic Septum (IMS) as a relatively simple and inexpensive method to opti-mize both electrolyte flow and species transfer inside the devices. SCMFCs with the novel IMS, operated with sodium acetate as the carbon source, demonstrate to enhance the energy recovery (Erec) factor, defined as the ratio between the energy yield and the inner volume of electrolyte. In standard operative conditions, cells with IMS exhibit Erec value of (37±1) J/m3, with respect to (3.0±0.3) J/m3 of control cells. Furthermore, changing sodium acetate concentration the Erec values change accordingly. By monitoring the activity of a-SCMFCs for over one-year, beneficial impact of the IMS on both the initial inoculation phase and the long-term stability of electrical perfor-mance were observed. These improvements suggest the effectiveness of IMS to allow the de-velopment of efficient biofilms, likely due to the reduction in oxygen diffusion towards the anode. Electrochemical characterizations confirm that the presence of the IMS impacts the diffusion processes inside the electrolytic chamber, supporting the hypothesis of a beneficial effect on oxygen diffusion.

The fuel cell particularly the Proton Exchange Membrane Fuel Cell (PEMFC) is a new energy technology that plays a critical role in achieving market viability. The PEMFC has high power density, zero CO₂ emissions, and high conversion efficiency. However, with uniform distribution of fuel in PEMFC, we can improve the performance and reduce the cost. The PEMFC will be more efficient and effective in terms of renewable energy as a byproduct only water. Metal foam is used as an alternative for the channels in PEMFC. The model of PEMFC was established by using the ANSYS Fluent 3D Model. Then we proposed four configurations of PEMFC. The outcome demonstrates that Case IV provided outstanding performance if it is compared with the other three cases. In terms of power density, Case IV provided a high power density that is double that of Case I. The porosity of metal foam was investigated. The 0.6 porosity value is found as the optimal value. The uniform distribution of the fuel can be achieved at this value which leads to the outstanding current density.

The high dependence on light crude oil as the main source of energy in automobiles., industrial processes, source of raw material for various industrial synthesis have made the heavy crude more available in the world and open for research work on its potentials as a source of energy for the increasing population of the world in areas like energy source for powering big marine engines, energy source in heavy industrial machines e.t.c. Though the relatively unfavourable characteristics of heavy fuel oil such as; high viscosity, high probability of precipitating is a reasonable challenge to the possible utilization of heavy fuel as a source of energy in the areas highlighted above. These issues of heavy fuel oil are largely due to the presence of Asphaltene in it which is a large complex hydrocarbon in heavy fuel oil. Understanding the combustion potential of asphaltene is therefore an interesting and challenging problem that has attracted increasing attention from both academia and industry. This research work is aimed at carrying combustion studies on the Forcados (Ni-geria) heavy fuel fraction asphaltene HFFA extracted from Forcados crude Oil and examining its combustion characteristics with the view to examine it for future sweet heavy fuel generation for it source got low sulphur content, to ascertain the volatile composition, moisture and ash content. The HFFA extracted to determine physical characteristics of the HFFA extracted for fuel properties potentialities and this study was carried out to evaluate the chemical constituents of forcadous asphaltene lead-ing to the generaration of HFFA using GCMS. The Forcados asphaltene showed some good fuel properties when subjected to ce-tane number, API gravity, flash point and cloud point parameter test. Probing further with AAS for trace metal presence showed some high concentration on Chromium (Cr), Nickel (Ni), Iron (Fe), Lead (Pb), Cadmium (Cd), Copper (Cu), Manganese (Mn) and Zinc (Zn) indicating the potential for residual and soot formation after combus-tion. But still being a sweet asphaltene from Nigerian sweet crude source will be de-void of corrosive effect on machineries and heavy fuel engine if used to power it as in the case of high sulphur content in Venezuelan crude oil and some other world. The GCMS showed the decomposition of heavy crude asphaltene peaks and sig-naling the presence of heavy fuel fraction in the composition of the asphaltene while the FTIR and the UV-VIS identified the various functional groups in the compounds and the identification of signals that cannot be seen in the normal spectrum respec-tively.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Some global difficulties in the modern period include energy storage conversion. Researchers have looked to renewable energy resources to discover long-term answers to this dilemma. Fuel cells are one example of prospective energy producing technology. Although these technologies appear to be very enticing, they are known to be expensive due to high expenses. Catalyst costs, as well as concerns concerning energy density. Pt based Electrocatalysts have traditionally been used to drive ORR and offer efficient power outputs. However, cost constraints have limited the use of these electrocatalysts, rendering them inefficient. Apart from the high price, Pt-based Electrodes are prone to time-dependent drift and CO deactivation, both of which occur gradually. Electrocatalysts deteriorate over time, reducing the efficiency of fuel cells. This is why alternative electrocatalysts are in high demand for future energy applications. This review covers the comparative study of Platinium and Non-Platinium based electrocatalyst in fuel cells, their shortcomings and recent advancement for efficient and optimized electrocatalyst.

In Nigeria, the adoption of sustainable biomass for energy generation is on the rise. One crucial factor that affects the efficiency of Biomass utilization is the moisture content. This study investigates the economic impact of moisture at different stages of the wood biomass distribution chain, considering the entire chain. The methodology employed includes a comprehensive literature review, interviews, and economic calculations. By analyzing these factors, this research aims to provide valuable insights into the economics of moisture in wood biomass, contributing to the sustainable development of the Biomass energy sector in Nigeria. Based on the outcomes of this investigation, it has been discovered that the costs associated with moisture content in Nigeria amount to approximately ₦500,000,00 (Five Hundred Thousand Naira only). Utilizing wood Biomass with a moisture content of 32% weight, as opposed to 18% weight, has proven to be more costly. Transportation contributes to a significant portion of this increase, while the reduction in burning efficiency accounts for the remaining half. To further elaborate on these findings, it is crucial to understand that the transportation costs are impacted by the additional weight and volume of biomass with higher moisture content. This necessitates the use of more fuel and resources during transportation, resulting in increased expenses. Additionally, the decreased burning efficiency associated with higher moisture content poses a challenge. It leads to reduced energy output and increased fuel consumption, ultimately impacting the overall economic viability of wood biomass as an energy source. By identifying these factors, this study aims to provide insights into the economic implications of moisture content in the wood biomass distribution chain in Nigeria. These findings can serve as a basis for developing strategies to optimize the use of biomass, reduce costs, and enhance the sustainability of the energy generation process. One of the most convenient and cost-effective solutions to reduce transportation expenses and improve combustion efficiency is through planned air drying of wood biomass. Large-scale power plants typically prefer utilizing wood biomass that has undergone air drying, resulting in a moisture content ranging from 18% to 36% by weight. By implementing planned air-drying techniques, the moisture content of wood biomass can be significantly reduced, thereby decreasing transportation costs. As the biomass becomes lighter and less bulky, transportation requirements are optimized, leading to enhanced efficiency and reduced expenses. Moreover, air-dried wood biomass offers improved combustion characteristics. The reduced moisture content allows for better heat transfer during the combustion process, resulting in higher energy output and increased fuel efficiency. This not only improves the overall economics of utilizing wood biomass but also contributes to a more sustainable and environmentally friendly energy generation system. The application of planned air drying in the wood biomass distribution chain in Nigeria can serve as a practical solution to address the economic challenges associated with moisture content. By adopting this approach, stakeholders can maximize the potential of wood biomass as a renewable energy resource while minimizing costs and promoting sustainable practices.

Accurate fuel mapping plays a crucial role in fire detection and management strategies. This paper presents a method for discriminating between wildfire fuel types by exploiting together remote sensing data and Convolutional Neural Networks (CNN). Specially, a CNN-based classification approach that leverages Sentinel-2 imagery is exploited to accurately classify fuel types into seven preliminary main classes (conifers, broadleaf, shrubs, grass, bare soil, urban areas, and water bodies) with an high accuracy of 0.99$\%$. To further refine the fuel mapping results, subclasses were generated from the seven principals by using biomass and bioclimatic maps. These additional maps provide complementary information about vegetation density and climatic conditions, respectively. By incorporating this information, we align our fuel type classification with the widely used Scott/Burgan fuel classification system. This refinement step allows for a more detailed and comprehensive assessment of fuel types, enhancing the accuracy and effectiveness of fire management efforts, which can be utilized by fire management agencies, policymakers, and researchers for improved fire behavior prediction and mitigation practices. The proposed approach presents a valuable tool for enhancing fire management, contributing to more effective wildfire prevention and mitigation efforts.

Zero-emission trucks for regional and long haul missions are an option for fossil-free freight. The viability of such powertrains and system solutions was studied conceptually in project ESCALATE for trucks with GVW of 40 tonnes and beyond through various prime mover combinations. The study covers battery and fuel cell power sources with different degrees of battery electric as well as H2 and fuel cell operation. As a design basis, two different missions with a single-charge/H2 refill were analysed. The first mission was the VECTO long haul profile repeated up to 750 km, whereas the second was a real 520 km on-road mission in Finland. Based on the simulated energy consumption on the driving cycle, on-board energy demand was estimated, and the initial single-charge operational scenarios were analysed with five different power source topologies. The traction motors of the tractor were dimensioned so that a secondary mission of GVW up to 76 tons on a shorter route can be operated. Based on the powertrain and vehicle model, various infrastructure options for charging and H2 refuelling strategy as well as various operative scenarios with indicative total cost of ownership (TCO) were analysed.

During the launch and return of a spacecraft, the intense combustion of propellants generates strong electromagnetic radiation, which interferes with the operation of electronic equipment in the spacecraft. To improve the electromagnetic compatibility of electronic equipment in spacecraft, it is necessary to study the electromagnetic radiation characteristics of rocket fuel. An electromagnetic radiation measurement system based on antennas is designed to measure the electromagnetic radiation generated by rocket fuel, and the electromagnetic radiation characteristics are obtained through data analysis. The mechanism of the electromagnetic radiation generated by rocket fuel is comprehensively analysed through the spatial, time-domain, frequency-domain, and energy-domain characteristics. A characterization model is established to provide a reliable scheme for evaluating the influence of rocket fuel electromagnetic radiation on electronic equipment in spacecraft.

This research work studies the characteristics of wear and wear resistance of composite powder coatings, deposited by high-velocity oxygen fuel, which contain composite mixtures Ni-Cr-B-Si having different chromium concentrations – 9.9%; 13.2%; 14%; 16% and 20% , at one and the same size of the particles and the same content of the remaining elements. The coating of 20% Cr does not contain B and Si. Out of each powder, composite coatings have been prepared without any preliminary thermal treatment of the substrate and with preliminary thermal treatment of the substrate up to 650оС. The coatings have been tested under identical conditions of dry friction over a surface of solid firmly attached abrasive particles using the tribological testing device „Pin-on-disk“. Results have been obtained and the dependences of the hardness, mass wear, intensity of the wearing process, absolute and relative wear resistance on the Cr concentration under identical conditions of friction. It has been found out that for all the coatings the preliminary thermal treatment of the substrate leads to a decrease in the wear intensity. Upon increasing Cr concentration the wear intensity diminishes and it reaches minimal values at 16% Cr. In the case of coatings having 20% Cr concentration, the wear intensity is increased, which is due to the absence of the components B and Si in the composite mixture, whereupon no inter-metallic structures are formed having high hardness and wear resistance. The obtained results have no analogues in the current literature and they have not been published by the authors.

Firebrands are an important agent of wildfire spread and structure fire ignitions at the wildland urban interface. Bark flake morphology has been highlighted as an important, yet poorly characterized factor in firebrand generation, transport, deposition, and ignition of unburned material. Using pine species where bark flakes are the documented source of embers, we conducted experiments to investigate how bark structure changes in response to diurnal drying. Over a 3-day period in a longleaf pine (Pinus palustris Mill.) stand in Florida, we recorded changes in temperature, moisture content and structure of bark across different facing aspects of mature pine trees to examine the effects of varying solar exposure on bark moisture. We further compared results to bark drying in a pitch pine (Pinus rigida Mill.) plantation in New Jersey. Under all conditions, bark peeled and lifted away from the tree trunk over the study periods. Tree bole aspect and the time of day interacted to significantly affect bark peeling. General temperature increases and moisture content decreases were significantly different between east and west aspects in pitch pine, and with time of day and aspect in longleaf pine. These results illustrate that bark moisture and flakiness is highly dynamic on short time scales, driven largely by solar exposure. These diurnal changes likely influence the probability of firebrand production during fire events via controls on moisture (ignition) and peeling (lofting).

Exsolved perovskites can be obtained from lanthanum ferrites, such as La0.6Sr0.4Fe0.8Co0.2O3, as result of Ni doping and thermal treatments. Ni can be simply added to the perovskite by an incipient wetness method. Thermal treatments include calcination in air (e.g., 500 °C) and subsequent reduction in diluted H2 at 800 °C to favor the exsolution process. The chemistry of the nanoparticles exsoluted on the substrate surface can be further modulated by a post treatment in air. These processes allow to produce a two-phase material consisting of a Ruddlesden-Popper type structure and a solid oxide solution e.g. α-Fe100-y-zCoyNizOx oxide. The formed electro-catalyst shows sufficient electronic conductivity under reducing environment at the SOFC anode. Outstanding catalytic properties are observed for the direct oxidation of dry fuels in SOFCs, including H2, methane, syngas, methanol, glycerol and propane. This anode electrocatalyst can be combined with full density electrolyte based on Gadolinia-doped Ceria or with La0.8Sr0.2Ga0.8Mg0.2O3 (LSGM) or BaCe0.9Y0.1O3-δ (BYCO) to form a complete perovskite structure-based cell. Moreover, the exsolved perovskite can be used as a coating layer or catalytic pre-layer of a conventional Ni-YSZ anode. Beside the excellent catalytic activity, this material also shows proper durability and tolerance to sulphur poisoning. In this mini review, preparation methods, physico-chemical characteristics, surface properties of exsoluted and core-shell nanoparticles encapsulated on the metal-depleted perovskite substrate surface, electrochemical properties for the direct oxidation of dry fuels and related electrooxidation mechanisms are examined and discussed.

Microbial Fuel Cells (MFCs) representing a promising technology for the extract of energy and resources through wastewater and it also offer an economic solution to the problem of environment effluent and energy crisis in near future. The advance device is rather appealing, due its potential benefits, its practical application is, however hindered by several drawbacks, such an internally competing microbial reaction, and low power generation. This report is an endeavor to address various design connected to the MFCs application to wastewater treatment, in particular cost effective bioelectricity from waste water are reviewed and discussed with a multidisciplinary approach. The conclusions drawn herein can be of practical interest to all new researchers dealing with effluent wastewater treatment using MFCs.

The article considers the issues of ensuring operational performance and environmental sustainability of marine diesel engines by using biodiesel fuel. The research was conducted on 5S60ME-C8 MAN-B&W Diesel Group and 6DL-16 Daihatsu Diesel marine diesel engines, which were operated using RMG380 petroleum fuel and B10 and B30 biodiesel fuels. The efficiency of biofuel usage was assessed based on environmental (reduced nitrogen oxide concentration in exhaust gases) and economic (increased specific effective fuel consumption) criteria. It was found out that the use of B10 and B30 biofuels provides reduction of nitrogen oxides concentration in exhaust gases by 14.71–25.13 %, but at the same time increases specific effective fuel consumption by 1.55–6.01 %. Optimum fuel injection advance angles were determined that ensure the best thermal energy, economic and environmental performance of diesel engines. The optimum angle of biofuel supply advance is determined experimentally and should correspond to the limits recommended by the diesel engine operating instructions. It has been proven experimentally that the use of biofuel increases the environmental sustainability of marine diesel engines by 13.75–29.42 %. It increases the diesel engines environmental safety in case of emergency situations, as well as accidental and short-term emissions of exhaust gases with an increased content of nitrogen oxides into the atmosphere - phenomena that are possible in starting modes of diesel engine operation, as well as in modes of sudden load changes. It is the increase in the environmental friendliness of marine diesel engines in the case of using biofuel that is the most positive criterion and contributes to the intensity of biofuel use in power plants of sea vessels.

Plastics have become an indispensable part of modern life today. The global production of plastics has gone up to 299million tones in 2013, which is believed to be increasing in the near future. The utilization of plastics and its final disposal pose a tremendous negative significance impacts on the environment. The aim of this study was to investigate the thermal and catalytic pyrolysis for production of fuel oil from the polyethene plastic wastes. Catalysts used in the experiment were acid activated clay mineral and aluminum chlorides on activated carbon. The clay mineral was activated by refluxing it with 6M Sulphuric acid for 3hours. The experiment was conducted in three different phases: the first phase of the experiment was done without a catalyst where 88mL oil was obtained at a maximum temperature of 39 and heating rates of 12.5, reaction time of 4hours. The second phase involves the use of acid activated clay mineral where 100mL of oil was obtained and heating rates of 12.5 and reaction time of 3hours 30minutes. The third phase was done using aluminium chlorides on activated carbon and 105ml oil was obtained at a maximum temperature of 400 and heating rates of 15.5 reaction time of 3hours 10minutes. From the results, catalytic pyrolysis is more efficient than purely thermal pyrolysis and homogenous catalysis (aluminum chlorides) shows a better result than solid acid catalyst (activated clay minerals) hence saving the energy needed for pyrolysis and making the process more economically feasible.

A tailored model for the assessment of environmental benefits achievable by “light-weighting” in the automotive field is presented. The model is based on the Fuel Reduction Value (FRV) coefficient, which expresses the Fuel Consumption (FC) saving involved by a 100 kg mass reduction. The work is composed of two main sections: simulation and environmental modelling. Simulation modelling performs an in-depth calculation of weight-induced FC whose outcome is the FRV evaluated for a wide range of Diesel Turbocharged (DT) vehicle case studies. Environmental modelling converts fuel saving to impact reduction basing on the FRVs obtained by simulations. Results show that for the considered case studies, FRV is within the range 0.115–0.143 and 0.142–0.388 L/100 km × 100 kg, respectively, for mass reduction only and powertrain adaptation (secondary effects). The implementation of FRVs within the environmental modelling represents the added value of the research and makes the model a valuable tool for application to real case studies of automotive lightweight LCA.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

We investigated the influence of the fuel change, from pure hydrogen to hydrogen-ammonia mixture at different percentage, on the electrochemical behaviour of 50 mm in diameter Solid Oxide Fuel Cells (SOFC) with sputtered thin buffer layers of Gd doped Ceria, varying the working temperatures from 800°C to 650°C. The results show that the performances of the cells are not affected by the fuel change for the high working temperatures (800°C and 750°C). As an example, a power density value of 802 mW∙cm-2 at 1 A∙cm-2 is found when directly feeding the cell with 8 Nml∙min-1cm-2 of ammonia and with an equivalent flowrate of 12 Nml∙min-1cm-2 of H2. These power density output values are comparable to those obtained in industrial State of Art (SoA) SOFC cells with screen printed buffer layers fed with higher hydrogen flowrates, thanks to the improved electrochemical performances obtained in the case of cells with sputtered thin buffer layers of Gd doped Ceria. At lower working temperatures (700°C and 650°C), slight changes in the electrochemical behaviour of the cells are observed. Nevertheless, also in this temperature range, we obtain an output current density value of 0.54 A∙cm-2 in pure ammonia flowrate of 12 Nml min-1cm-2, at 800 mV and 700°C, equal to the value observed in SoA button cells with industrial screen printed GDC barrier layer fuelled with 16 Nml∙min-1cm-2 of H2. These results pave the way towards the use of innovative SOFC structures with sputtered thin buffer layers fuelled by ammonia.

Alternative fuels have the potential to reduce exhaust emissions in the transportation sector. In this study, the effects of oxygenated fuels on the performance and emissions of a gasoline single-cylinder spark-ignition engine have been investigated experimentally. Experiments were conducted using a DIDACTA-T85 testbed under full load conditions and variable engine speed. Performance tests were performed by measuring the brake torque, brake power, brake mean effective pressure (BMEP), brake specific fuel consumption (BSFC), and brake thermal efficiency (BTE). The tested fuel blends were G0, E10, A10, and M10. G0 represented the base fuel and pure gasoline. E10, A10, and M10 were represented by a 10% volume of ethanol, acetone, and methanol in gasoline respectively. Results showed that M10 produced better engine performance in terms of brake torque, brake power, and BMEP, while E10 performed better results in terms of BSFC and BTE. A10 gave the lowest value in NOx emission at all engine speeds. On the other hand, it increased the NOX emission for E10 and M10 blends. This study showed that oxygenated fuel blends significantly reduced carbon monoxide emission at all engine speeds whereas carbon dioxide emission was higher at the highest engine speed.

The results from laboratory tests and field tests, available in the open literature for over ten years, despite the announcement of high efficiency translating into increased energy efficiency and such significant ecological advantages, have not so far resulted in widespread use of fuel performance catalysts (FPC) on a global scale. Wishing to explain why the above situation occurred and to verify the operation of catalytic additives for fuels; this article presents the results of research on the effect of using catalytic additives for fuel in a brand new diesel engine. The article contains an analysis of the results of exhaust gas emission tests from the Doosan MD196TI engine. During the tests, the engine was fueled with a typical diesel fuel and the same fuel with the a catalyst additive. The catalyst was added to the liquid fuel in the form of a commercially available product distributed by ProOne company under the name FMAX. The research was carried out in the form of a test, much more developed than the approval test on a stationary braking station in accordance with the requirements of ISO 8178. The article is concluded with a comparative analysis of exhaust gas emission results illustrating the effects of a catalyst in the form of reduction of solid particles, carbon monoxide, hydrocarbons and a slight increase in nitrogen oxide emissions. In addition, the effect of the catalyst depends on the product of thermal (brake) efficiency of the engine and the calorific value (CV) of the fuel used.

Durability and performance of electrochemical energy converters such as fuel cells and electrolysers are not only dependent on the properties and the quality of the used materials. They strongly depend on operation conditions. Variations in external parameters, such as flow, pressure, temperature and, obviously, load can lead to significant local changes of current density, even local transients. The segmented cell technology was developed with the purpose to gain insight into local operation conditions in electrochemical cells, during operation. The operando measurement of the local current density and temperature distribution allows effective improvement of operation conditions, mitigation of potentially critical events and assessment of the performance of new materials. The segmented cell, which can replace a regular bipolar plate in the current state of the technology, can be used as monitoring tool and for targeted developments. This article gives an overview over the development and applications for proton exchange membrane fuel cell of this technology, such as water management or fault recognition. Recent advancements towards locally resolved monitoring of humidity and to current distributions in electrolysers are outlined.

Due to low working temperature, high energy density and low pollution, proton exchange fuel cells have been investigated under different operating conditions in different applications. Using platinum catalysts in methanol fuel cells leads to increasing the cost of this kind of fuel cell which is considered as a barrier to the commercialism of this technology. For this reason, a lot of efforts have been made to reduce the loading of the catalyst required on different supports. In this study, carbon black (CB) and carbon nanotubes (CNT) have been used as catalyst supports of the fuel cell as well as using the double-metal combination of platinum-ruthenium (PtRu) as anode electrode catalyst and platinum (Pt) as cathode electrode catalyst. The performance of these two types of electro-catalyst in the oxidation reaction of methanol has been compared based on electrochemical tests. Results showed that the carbon nanotubes increase the performance of the micro-fuel cell by 37% at maximum power density, compared to the carbon black. Based on thee-electrode tests of chronoamperometry and voltammetry, it was found that the oxidation onset potential of methanol for CNT has been around 20% less than CB, leading to the kinetic improvement of the oxidation reaction. The current density of methanol oxidation reaction increased up to 62% in CNT sample compared to CB supported one, therefore the active electrochemical surface area of the catalyst has been increased up to 90% by using CNT compared to CB which shows the significant rise of the electrocatalytic activity in CNT supported catalyst. Moreover, the resistance of the CNT supported sample to poisonous intermediate species has been found 3% more than CB supported one. According to the chronoamperometry test results, it was concluded that the performance and sustainability of the CNT electro-catalyst show remarkable improvement compared to CB electro-catalyst in the long term.

Kampala is the capital city of Uganda. Over the years the population growth in the city has more than doubled, and this has increased the demand for energy. However, electricity and gas are not only limited in supply but are also expensive for the majority of the households hence the use of charcoal remains the main source of energy. There is little known about the energy situation in big cities of Africa, and Kampala is not an exception. Therefore, we examine the urban nexus amidst energy poverty, vulnerability, and resilience with a focus on; the role of charcoal in the urban Nexus in Kampala Uganda. Literature review and content analysis of scientific materials such as journal articles and reports were done. Charcoal fuel in Kampala and surrounding urban areas does not only facilitate cooking meals and boing water for over 95% of households but also a source of livelihood for many women in the nexus. This process impacts not only on energy use but also the entire water, energy, and food system in the urban nexus. Even though charcoal fuel doubles as a source of household income, it is greatly responsible for most deforestation. Furthermore, charcoal production also accounts for prolonged droughts hence impacting on water and food supply in the nation. Therefore, we propose subsidizing alternatives such as gas and electricity to reduce the complete reliance on charcoal.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

Nuclear waste is one of the most important environmental problems of nuclear power plants. A novel renewable distillation method has been proposed for an on-site recycling of the spent nuclear fuel and separation of its valuable components from the fissile isotopes, which is especially applicable for reactors using liquid fuels.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

Integrated photovoltaic-fuel cell (IPVFC) systems, amongst other integrated energy generation methodologies are renewable and clean energy technologies that have received diverse research and development attentions over the last few decades due to their potential applications in a hydrogen economy. This article systematically updates the state-of-the-art of IPVFC systems and provides critical insights into the research and development gaps needed to be filled/addressed to advance these systems towards full commercialisation. The design methodologies, renewable energy-based microgrid and off-grid applications, energy management strategies, optimisations and the prospects as self-sustaining power source were covered. IPVFC systems could play an important role in the upcoming hydrogen economy since they depend on solar hydrogen which has almost zero emissions during operation. Highlighted herein are the progresses as well as the technical challenges requiring research efforts to solve to realise numerous potential applications of IPVFC systems such as in unmanned aerial vehicles, hybrid electric vehicles, agricultural applications, telecommunications, desalination, synthesis of ammonia, boats, buildings, and distributed microgrid applications.

This study investigates the performance and environmental impact of n-butanol blended with Jet-A fuel in turbo-engines, aiming to assess its viability as a sustainable aviation fuel (SAF). The research involves experimental testing of various blends, ranging from low to high concentrations of methanol, to determine their effects on engine performance and emissions. The experimental setup includes comprehensive measurements of engine parameters such as thrust, fuel consumption rates, and exhaust gas temperatures. Emissions of nitrogen oxides (NOx), particulate matter (PM), carbon monoxide (CO), and unburned hydrocarbons (HC) are also analysed to evaluate environmental impacts. Key findings indicate that n-butanol/Jet-A blends can significantly enhance combustion efficiency and reduce emissions compared to conventional Jet-A fuel. Higher n-butanol concentrations lead to improved thermal efficiency and lower NOx and CO emissions. However, PM emissions slightly increase with higher methanol content. The study underscores the potential of n-butanol as a SAF for turbo-engines, highlighting its ability to mitigate environmental impacts while maintaining or improving engine performance. This research supports the feasibility of integrating n-butanol into Jet-A blends for turbo-engine applications, emphasizing its role in achieving more environmentally friendly aviation operations.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

A study was conducted on the power system of a forklift equipped with PEM fuel cells. A fuel cell assembly relies on several components for proper functioning, and among these, the air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, we delved into the impact of varying the stoichiometric ratio of air and air pressure on the validated and optimized power module model. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor, being a pivotal component of a PEM fuel cell system, can be oper-ated at different excess air and pressure ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of polymer electrolyte membrane (PEM) fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were con-ducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications.

This work reports the influence of reduced graphene oxide (rGO) support on the catalytic performance of Cu@PtRu/rGO catalysts towards methanol oxidation in acidic medium. These core-shell catalysts are synthesized by the reduction method in two steps being the first using ethylene glycol to obtain Cu/rGO and the second, the reduction of copper atoms synthesized in the previous step to produce Cu@PtRu/rGO. In order to compare the catalytic performance of the prepared catalysts, Pt/C, PtRu/C, Cu@PtRu/C catalysts are also synthesized on Vulcan XC-72R carbon. The theoretical loading of Pt used in the Vulcan XC-72R carbon supported catalysts is equal to that utilized in Cu@PtRu/rGO, and higher in the other prepared catalysts. The surface composition of the nanoparticles, as well as their sizes, particle size distribution and morphology of the catalyst particles are characterized by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Cyclic voltammetry (CV) and chronoamperometry (CA) are employed to measure the electrochemical performance of the prepared catalysts. The anodic scans show that for the region of technological interest (0.1 to 0.4 V), the Cu@PtRu/rGO-16 electrocatalyst exhibits higher current density value than the others as a result of its lower starting oxidation potential (0.250V against 0.437V for Pt/C) and its higher ratio between forward (iF) and reverse (iR) current densities (iF/iR 1.45 against 0.93 for Pt/C). Chronoamperometric tests depict that the current density value of Cu@PtRu/rGO-16 catalyst is about 4 times higher than that of Cu@PtRu/C-16 and Cu@PtRu/C-18 catalysts, ca. 4.8 times higher than that of PtRu/C-30 catalyst and around 6 times higher than that of Pt/C-30. These results suggest that Cu@PtRu/rGO-16 exhibits high bulk activity for the electrooxidation of methanol, high stability and high tolerance to CO poisoning, making it possible to reduce the platinum loading in proton exchange membrane fuel cells (PEMFCs).

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

Grill-specific footprints for common fuels/grill types in the USA are estimated from public information and data from a major grill manufacturer. These are a function of both 1) a fuel’s footprint and 2) a grill’s efficiency of cooking. In 2022, grill-specific footprints vary by 9:1. A typical gas grill is highest at 3.6 lb CO2e/grill session, nine times that of a wood-pellet grill, lowest at 0.4 lb. Charcoal briquettes, electricity and super-efficient gas grills come in-between. Pellets are lowest, because they are made from waste wood and their production burden is modest. Electricity has the highest fuel footprint, yet the second-lowest grill-specific footprint, thanks to its high efficiency. Briquettes come in fourth, because their production involves fossil gas, and they contain some fossil coal. Grill efficiency is key for gas (natural gas or propane): a typical gas grill has twice the footprint of a super-efficient one. In 2027, with bio substitution, the super-efficient gas grill would move ahead of pellets. Electricity and charcoal could improve but would still place fifth and sixth. The range of grill-specific footprints could fall to 4.5:1, within a much-lower range, the highest footprint in 2027 almost 60% lower than 2022’s highest.

The previously developed models for fuel droplet heating and evaporation processes, mainly the Discrete Multi Component Model (DMCM), and Multi-Dimensional Quasi-Discrete Model (MDQDM) are investigated for the aerodynamic combustion simulation. The models have been recently improved, and generalised for a broad range of bio-fossil fuel blends so that the application areas are broadened with increased accuracy. The main distinctive features of these models are that they consider the impacts of species thermal conductivities and diffusivities within the droplets to account for the temperature gradient, transient diffusion of species and recirculation. A formulation of fuel surrogates is made, using the recently introduced model, referred to as ‘’Complex Fuel Surrogate Model (CFSM)’’ and analysing their heating, evaporation, and combustion characteristics. The CFSM is aimed to reduce the full composition of fuel to a much smaller number of components based on their mass fractions, and to formulate fuel surrogates. Such approach has provided a proof of concept with the implementation of the developed model into a commercial CFD code ANSYS-Fluent. A case study is made for the CFD modelling of gas-turbine engine using kerosene fuel surrogate. The surrogate is proposed using the CFSM. The model is implemented into ANSYS-Fluent via a user-defined function to provide the first full simulation of the combustion process. Detailed chemical mechanism is also implemented into ANSYS Chemkin for the combustion study.

Many contaminant yeast strains able to survive inside fuel ethanol industrial vats show detrimental cell surface phenotypes, such as filamentation, invasive growth, flocculation, biofilm formation and excessive foam production. Previous studies have linked some of these phenotypes to the expression of FLO genes, and the presence of gene length polymorphisms causing the expansion of FLO gene size appears to result in stronger flocculation and biofilm formation phenotypes. We have performed here a molecular analysis of FLO1 and FLO11 gene polymorphisms present in contaminant strains of S. cerevisae from Brazilian fuel ethanol distilleries showing strong foaming phenotypes during fermentation. The size variability of these genes was correlated with cellular hydrophobicity, flocculation and highly foaming phenotypes in these yeast strains. Our results also show that deleting the major activator of FLO genes (the FLO8 gene) from the genome of a contaminant and highly foaming industrial strain avoids problematic foam formation, flocculation, invasive growth and biofilm production by the engineered (flo8∆::BleR / flo8Δ::kanMX) yeast strain. Thus, the characterization of highly foaming yeasts and the influence of FLO8 in this phenotype opens new perspectives for yeast strain engineering and optimization in the sugarcane fuel-ethanol industry.

The purpose of this paper is to evaluate the acceptance and the utilization of GPS/GPRS-based telematics technology in road transport companies registered in Poland. Telematics technologies are essential for management of energy saving and emissions reduction in road transport. It is in line with the European Union policy of sustainable transportation. The evaluation is based on a survey designed and carried out in 2020. The issues concerning the scope of telematics systems utilization as well as the internal and external factors affecting their use are analysed. The methodology is based on Technology Acceptance Model (TAM) and Structural Equation Modelling (SEM). The results are checked for robustness. Based on the results, it can be reasoned that as a result of the COVID19 pandemic, the companies started to use telematics systems more widely than they did before. Furthermore, the companies employing more people recognize the higher usefulness of telematics systems and are motivated to have the systems more than smaller enterprises; however, TAMs estimated separately for small and medium-sized enterprises did not reveal any significant differences in the parameter estimates.

Ammonia produced using renewable hydrogen is being viewed as a promising media for the export of energy from locations rich in renewable energy sources. Solid oxide fuel cells (SOFCs) are efficient devices for converting such exported ammonia back into electricity at the point of use, however investigations on materials and operating regime for direct ammonia fuelled SOFCs are limited. The studies on fuel electrodes tailored specifically for ammonia fuel are limited. In this work, we evaluated the direct ammonia SOFC performance with Silver-Lanthanum Strontium Cobalt Ferrite (Ag-LSCF) composite anode and a novel Palladium (Pd) nanoparticle decorated Silver-Lanthanum Strontium Cobalt Ferrite (Pd-Ag-LSCF) composite anode in the temperature range of 500 °C to 800 °C. It is hypothesized that Palladium nanoparticles in the anode provide hydrogen dissolution and shift the ammonia decomposition reaction towards the right. The cell performance was evaluated with both hydrogen and ammonia as fuels and a clear-cut improvement in the performance was observed with the addition of Pd for both the fuels. The results showed a performance enhancement by 20% and 43% with hydrogen and ammonia fuels respectively from the Pd addition of Ag-LSCF anode. Open circuit voltage (OCV) values of the cells with hydrogen and ammonia fuel recorded over the temperature range of 500 °C to 800 °C indicated the possibility of direct electro-oxidation of ammonia in SOFCs.

Since World War I, the commercial aviation industry has seen many improvements that now allow people and goods to reach the other side of the world in few hours, consuming much less fuel than in recent decades. Improvements in cargo capacity and energy efficiency were significant and, in this scenario, commercial airlines were able to thrive and bring great benefits to world economy. However, this sector is facing environmental challenges due to the intensive use of aviation fuel. Brazil is one of the largest domestic air passenger markets in the world and still has great growth potential, considering its economic potential and territorial dimensions: roughly the same size as the US and twice the size of the European Union. This paper discusses partial productivity of jet fuel in Brazilian domestic aviation and proposes an econometric method to support public regulators and airlines decisions. The proposed model uses variables such as aircraft size, route characteristics and idle flight capacity in a panel data analysis. The results show that reducing idle capacity is one of the best ways to achieve better short-term fuel efficiency and therefore will reduce environmental impacts and have positive economic effects on commercial air transport activities.

A D-grade type coal was burned under simulated domestic practices in a controlled laboratory set-up, in order to characterize emissions of volatile organic compounds (VOCs); viz. benzene, toluene, ethylbenzene and xylenes (BTEX). Near-field concentrations were collected in a shack-like structure constructed using corrugated iron, simulating a traditional house found in informal settlements in South Africa. Measurements were carried out using the Synspec Spectras GC955 real-time monitor over a three-hour burn cycle. The 3-hour average concentrations (in µg/m³) of benzene, toluene, ethylbenzene, p-xylene and o-xylene were 919 ± 44, 2051 ± 91, 3838 ±19, 4245 41 and 3576 ± 49, respectively. The cancer risk for adult males and females in a typical SA household exposure scenario, was found to be 1.1 -1.2 and 110-120 folds higher than the US EPA designated risk severity indicator (1E^-6), respectively. All four TEX compounds recorded the Hazard Quotient (HQ) of less than 1, indicating a low risk of developing related non-carcinogenic health effects. The HQ for TEX ranged from 0.001– 0.05, with toluene concentrations being the lowest and ethylbenzene the highest. This study has demonstrated that domestic coal burning may be a significant source of BTEX emission exposure.

PEM fuel cell is a technology successfully used in the production of energy from hydrogen, allowing the use of hydrogen as an energy vector. It is scalable for stationary and mobile applications. However, the technology demands more research. An important research topic is fault diagnosis and condition monitoring to improve the life and the efficiency and to reduce the operation costs of PEMFC devices. Consequently, there is a need of physical models that let deep analysis. These models must be accurate enough to represent the PEMFC behavior and to allow the identification of different internal signals of a PEM fuel cell. This work presents a PEM fuel cell model that uses the output temperature in a closed loop, so it can represent the thermal and the electrical behavior. The model is used to represent a NEXA Ballard 1.2 kW; therefore it is necessary to fit the coefficients to represent the real behavior. Five optimization algorithms were tested to fit the model, three of them were taken from literature and two were proposed. Finally, the model with the parameters identified was validated with real.

The transition to renewable and sustainable energy sources is critical to solving the environmental and socioeconomic problems associated with the use of fossil fuel. This study uses an interdisciplinary approach to analyze the evolution, challenges and prospects of a sustainable energy transition in the context of recent discovery and exploitation of fossil resources. We study the case of Senegal from 2000 to 2027 and the role of natural gas in its energy transition. In 2000, Senegal's energy mix consisted of about 97% for fossil energy and only 3% for renewable energy. Nowadays, although fossil fuels are still dominant, but they account for about 70% of total electricity production. The country has indeed undertaken tremendous efforts to develop renewable energy sources including, solar, hydro and wind power, which currently account for about 30% of the total energy mix. Socio-economic indicators show that over the past two decades, Senegal's population and electricity production have grown significantly, leading to an increased energy demand/need. This growth has resulted in a five-fold increase in per capita energy consumption over the same period. Combining the strategic use of natural gas as a transition energy source with the continued development of renewable energy sources could make Senegal as a model for West Africa’s energy transition. The projections for 2027 suggest a structural shift in the energy mix, with natural gas, oil, and renewables at 47%, 32%, and 21%, respectively.

The increasing deployment of intermittent renewable energy sources necessitates effective methods for balancing the electrical grid to ensure stability and safety. Energy storage systems that can store excess electrical power during periods of low demand and release it during high demand are crucial for both short-term and long-term applications. Power-to-Gas is an innovative energy storage solution that converts surplus renewable electricity into gas fuels, such as hydrogen, which can be stored and used later. This hydrogen can serve multiple purposes, including energy storage and as fuel for transportation modes like cars, trams, trains, and buses. While most hydrogen today is derived from fossil fuels, solid-oxide electrolysis (SOE) offers a cleaner alternative by producing hydrogen without harmful emissions. SOE is also the most efficient method of electrolysis. This study aims to determine the operational parameters for an SOE system, including lower heating value (LHV)-based efficiency and total input power, using a mathematical model. Results are presented for three different operating temperatures and four different steam utilization ratios. The paper is structured as follows: the introduction provides the context and motivation for the study; the second section outlines the fundamentals of electrolysis and its various types; the third section delves into solid-oxide electrolysis and electrolyser systems; the fourth section describes the methodology, including the mathematical formulation and simulation software used; the fifth section presents the calculation results and conclusions; and the final section summarizes the findings.

As the demand for fossil fuels continues to rise and their availability becomes increasingly limited, it is crucial to explore innovative approaches to optimize fuel combustion in existing systems. Among various engines, diesel engines are heavily reliant on fluid motion within the engine cylinder, which plays a critical role in fuel-air mixing. This abstract focuses on the potential of dynamic mathematical model simulation for multi-compartment rotor compressed combustion engines, aiming to revolutionize power generation by enhancing fuel burning efficiency. By leveraging advanced simulation techniques, this research seeks to unlock new insights into fluid dynamics and optimize fuel-air mixing, leading to more efficient and sustainable energy utilization. Through this exploration, we aim to pave the way for groundbreaking advancements in the field of combustion engines, ultimately contributing to a greener and more sustainable future. In the realm of internal combustion engines, the fluid dynamics within the engine cylinder greatly influence the combustion processes and heat transfer. For compression ignition (C.I) engines, both the bulk gas motion and turbulence characteristics play vital roles in engine performance. This study focuses on enhancing the combustibility of the fuel-air mixture in C.I engines by modifying the engine design to induce turbulence through squish and tumble flows. The modification involves creating multiple compartments on the rotor crown, comprising three small chambers spaced 120º apart. By implementing this design, the aim is to optimize the fuel-air mixing and improve the overall combustion efficiency. Through comprehensive analysis and experimentation, we seek to revolutionize C.I engine technology and pave the way for more efficient and environmentally-friendly power generation. In this study, the performance of a compression ignition (C.I) engine with a multiple compartment rotor has been analyzed under motoring conditions using computational fluid dynamics (CFD) simulations with FLUENT software. The obtained results have been compared with those of a base C.I engine. The analysis focused on the effects of the modified engine design on the tumble ratio and squish velocity, which are important parameters for fuel-air mixing and combustion efficiency. The results indicated a significant improvement with the modified engine, with a 35% increase in tumble ratio and a 31% increase in squish velocity compared to the base engine. These findings suggest that the modified engine design has the potential to enhance fuel-air mixing and combustion performance, leading to improved overall engine efficiency. This research presents promising insights into the optimization of C.I engine design and contributes to the development of more efficient and environmentally-friendly power generation technologies..

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability in fuel cell application. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with chitosan content of 5 g and silica variations dosage of 2% and 4% while stirring at a constant speed for 2h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO2 from the Sol-gel method with composite membrane's optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10 -7 cm2/s in the first 30 minutes and 3.31 × 10-7 in the last 150 minutes. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. However, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

Increasing the loading density of nanoparticles on carbon support is essential for making Pt-alloy/C catalysts practical in H2-air fuel cells. The challenge lies in increasing the load-ing while suppressing the sintering of Pt-alloy nanoparticles. This work presents a 40% Pt-weighted sub-3 nm PtCo/C alloy catalysts via a simple incipient wetness impregnation method. By carefully optimizing the synthetic conditions such as Pt/Co ratios, calcination temperature and time, the size of supported PtCo alloy nanoparticles is successfully con-trolled below 3 nm, and a high electrochemical surface area achieves of 94 m2/g is achieved, which is 2.8 times of commercial PtCo/C-TKK catalysts. Demonstrated by elec-trochemical oxygen reduction reaction, PtCo/C alloy catalysts present an enhanced mass activity of 0.45 A/mg at 0.9 V vs. RHE, which is 1.7 times that of PtCo/C-TKK catalyst. Therefore, the developed PtCo/C alloy catalyst can potentially be a highly practical cata-lyst for H2-air fuel cells.

This study aims at investigating the catalytic performance of Pd, Pd/Pt, and Pd/Au nanocatalysts toward the 2-propanol electro-oxidation reaction (2POR) in an alkaline medium. The catalyst components (Pd, Pt, and Au) were sequentially electrodeposited onto a glassy carbon (GC) electrode surface and further characterized using electrochemical (cyclic voltammetry (CV)) and materials (Field-emission scanning electron microscopy (FE-SEM) coupled with energy dispersive X-ray (EDX)) characterization methods. The Pd/Au/GC catalyst showed the highest catalytic activity in terms of the highest oxidation current (0.386 mA) and the highest stability in terms of the highest obtained current after 1800 s of continuous electrolysis. This behaviour was attributed to the enhancement in the charge transfer kinetics where the Pd/Au/GC catalysts acquired the lowest charge transfer resistance (Rct, 1.85 kΩ) during the 2POR.

Biochemical oxygen demand (BOD) is one of the most important factors to consider when evaluating water contamination. BOD5 is the amount of oxygen consumed in five days by microorganisms that oxidize biodegradable organic materials in an aerobic biochemical manner. The primary objective of this effort is to use microbial fuel cells (MFCs) to shorten the time required for BOD5 measurements. We created a regression artificial neural network (AI), and the predictions we obtained for BOD5 measurements were taken over 6 – 24 hours with an average error of just 7%. The outcomes demonstrated by our AI MFC/BES BOD5 sensor’s viability for use in real-world scenarios.

This article presents new PEM fuel cell models with hexagonal and pentagonal designs. After observing cell performance improvement in these models, we optimized them. Inlet pressure and temperature were used as input parameters, and consumption and output power were the target parameters of the multi-objective optimization algorithm. Then we used artificial intelligence techniques, including deep neural networks and polynomial regression, to model the data. Next, we employed the RSM (Response Surface Method) method to derive the target functions. Furthermore, we applied the NSGA-II multi-objective genetic algorithm to optimize the targets. Compared to the base model (Cubic), the optimized Pentagonal and Hexagonal models averagely increase the output current density by 21.819\% and 39.931\%, respectively.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

Remanufacturing is a viable option to extend the useful life of an end-of-use product or its parts, ensuring sustainable competitive advantages under the current global economic climate. Challenges typical to remanufacturing still persist, despite its many benefits. According to the European Remanufacturing Network a key challenge is lack of accurate, timely and consistent product knowledge as highlighted in a 2015 survey of 188 European remanufacturers. With more data being produced by electric and hybrid vehicles, this adds to the information complexity challenge already experienced in remanufacturing. Therefore, it is difficult to implement real-time and accurate remanufacturing for the shop floor; there are no papers that focus on this within an electric and hybrid vehicle environment. To address this problem this paper attempts to (1) identify the required parameters/ variables needed for fuel cell remanufacturing by means of interviews (2) rank the variables by Pareto analysis (3) develop a casual loop diagram for the identified parameters/ variables to visualise its impact on remanufacturing (4) model a simple stock and flow diagram to simulate and understand data and information-driven schemes in remanufacturing.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

In the delicate context of climate change and global warming new technologies are being investigated in order to reduce pollution. The solid oxide fuel cell (SOFC) stands out as one of the most promising fuel cell technologies for directly converting chemical energy into electrical energy, with the added benefit of potential integration into co-generation systems due to its high-temperature waste heat. They also offer multi-fuel flexibility, being able to operate on hydrogen, carbon monoxide, methane, and more. Additionally, they could contribute to carbon sequestration efforts and, when paired with a gas turbine, achieve the highest efficiency in electricity generation for power plants. However, their development is still challenged by issues related to high-temperature materials, the design of cost-effective materials and manufacturing processes, and the optimization of efficient plant designs.To better understand SOFC operation, numerous mathematical models have been developed to solve transport equations coupled with electrochemical processes for three primary configurations: tubular, planar, and monolithic. These models capture reaction kinetics, including internal reforming chemistry. Recent advancements in modeling have significantly improved the design and performance of SOFCs, leading to a sharp rise in research contributions. This paper aims to provide a comprehensive review of the current state of SOFC modeling, highlighting key challenges that remain unresolved for further investigation by researchers.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Currently, conventional spark-ignition engines face challenges in meeting the ever-growing demands of customers and increasingly stringent regulations regarding pollutant emissions. A combination of innovative strategies and carbon-neutral fuels is deemed necessary in order to further reduce fuel consumption and minimize engine emissions. The present work aims to assess the performance of combustion strategies using low-carbon content fuel, such as methanol M100, ignited by a plasma-assisted igniter (PAI) under ultra-lean conditions. The experimental campaign is conducted on a single-cylinder research engine at different engine speeds and low loads, moving up to the engine lean stable limits. To determine the benefits brought by the proposed strategy, referred to as M100-PAI, the obtained outcomes are compared with the ones obtained using market gasoline E5 ignited by the PAI system and conventional spark. The synergy between M100 (methanol) and Plasma Assisted Ignition (PAI) in internal combustion engines yielded notable benefits. This combination significantly improved combustion stability if compared to the other combinations tested, by extending the lean stable limit to λ=2.0, reducing cycle-to-cycle variability, and facilitating faster flame front acceleration, resulting in enhanced homogeneity. These enhancements, obtained with the combination M100-PAI, contributed to higher fuel efficiency showing a 10% efficiency gain over the combination E5-gasoline spark ignition.

Hydrogen fuel is gaining particular attention in internal combustion engines. In addition to zero-carbon emissions, major advantages relate to its combustion characteristics, which allow significant increase in thermal efficiency under ultra-lean operation and with very low NOx levels. The ignition system is one of the main technology enablers, as it determines the capability to control ultra-lean operations, avoid backfire phenomena, or reduce the risks of abnormal combustions. The latter results from the hydrogen low ignition energy and it is associated with factors like high-temperature residuals, hot spots, and irregular spark plug discharge. ACIS gen 2-Barrier Discharge Igniter excels in accelerating the initial flame growth speed by the generation of non-equilibrium low-temperature plasma, strong ignition promoter for the combined action of kinetic and thermal effects. Moreover, its volumetric discharge facilitates combustion initiation on a wide region, in contrast to the localized ignition of traditional spark systems. In this work we present for the first time, to the best of our knowledge, experimental results showing the performance of a hydrogen engine with a low-temperature plasma discharge. Tests were conducted on a single-cylinder research engine, achieving ultra-lean conditions with cycle-to-cycle variability results below 2.5%. The analysis indicates that the H2 - BDI combined solution is capable of accelerating the evolution of the flame front compared to traditional spark plugs, leading to a significant reduction in the cycle-to-cycle variability. A meticulous adjustment of the BDI control parameters further enhances igniter performance and contributes to a deeper understanding of the innovative approach proposed in this study.

Electronic waste (e-waste), characterized by the widespread disposal of electronic devices, shows a growing environmental challenge. In this study, we explore the electrocatalytic potential of gold nanoparticles supported on Vulcan obtained from e-waste for their application as electrocatalysts for the methanol oxidation reaction in alkaline media. Gold nanoparticles are synthesized from gold coatings recovered from Intel Pentium 4 processor pins, highlighting their sustainability as electrocatalyst precursors. Comprehensive characterization, including UV-Vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray dif-fraction, is performed to assess the electrocatalyst's structural properties. Electrochemical evalu-ation is carried out in 0.5 M KOH electrolyte employing the rotating disk electrode technique, us-ing cyclic voltammetry for the study of methanol oxidation. Remarkably, the gold nanoparticles show electrocatalytic activity on par with commercially synthesized counterparts, demonstrating the feasibility of this approach for sustainable electrocatalyst production. Thus, this research opens new routes for utilizing e-waste as a source of valuable catalyst materials, addressing en-vironmental and technological challenges in the field of alkaline fuel cells.

Integrating sustainable processes and innovative waste utilization not only addresses environ-mental challenges but also aligns with evaluating energy sustainability and creating the circular waste management. This study presents a comparative analysis of liquid fuel production from waste tires and water hyacinth using two thermochemical methods: co-pyrolysis (direct method) and co-gasification integrated with the Fischer-Tropsch (FT) process (indirect method). The As-pen Plus simulation software version 9 is employed to develop models, determining optimal operating conditions for maximum liquid fuel, and assessing economic viability. Co-pyrolysis simulations reveal an increase in oil products and a decrease in gas products with higher blending weight ratios of waste tires/water hyacinth (W/B) and lower pyrolyser temperatures. Operating at 400°C with a blending weight ratio of 75:25 provided the maximum liquid fuel rate of 6649.22 gal/day. For co-gasification, optimal conditions (W/B = 50:50, T = 800°C, steam to feed ratio (S/F) = 1) result in the highest syngas yield of 115.92 kmol/h. Fischer-Tropsch simulations demonstrate an increase in gasoline and a decrease in diesel with rising reactor temperatures. At 230°C, the maximum liquid fuel rate reaches 8817.15 gal/day. The economic and production yield analysis indicates that the indirect method better than the direct method, providing higher liquid fuel yields and investment worthiness.

Agricultural tractors are high fuel-consuming and polluting machines, thus the introduction of new sustainable technologies, as hybridization, can be very impactful for the development of electric hybrid agricultural tractors. These vehicles combine the classic internal combustion engine with an electric machine, to reduce the environmental impact and improve the efficiency. This paper reports the modeling and the simulation conducted, using a simulation software typically used for on-road vehicles, of a two wheel-drive agricultural tractor in three different configurations: the conventional one, the series and the parallel electric hybrid powertrain. The simulated task is the trailing of a big square baler during the process of straw wrapping and baling. The evaluation and the comparison of the fuel consumption, CO2 emissions and the depth of discharge of the different configurations has been carried out to determine if it is possible to downsize the ICE, maintaining the same performances. This study points out that the hybridization of agricultural tractors powertrains is one of the most promising approaches to reduce pollutant emissions and fuel consumption.

Soft materials bearing rigid, lightweight, and vibration-dampening properties offer distinct advantages over traditional wooden and metal-based fillings for spent fuel transport casks, due to their low density, tunable structure, excellent mechanical properties, and ease of processing. In this study, a novel type of rigid polyurethane foams is prepared using a conventional polycondensation reaction between isocyanate and hydroxy groups. Moreover, the density and size of the pore in these foams are precisely controlled through simultaneous gas generation. The as-prepared polyurethane exhibits high thermal stability exceeding 185 °C. Lifetime predictions based on thermal testing indicate that these polyurethane foams could last up to over 60 years, which is double lifetime of conventional materials of about 30 years. Due to their occlusive structure, the mechanical properties of these polymeric materials meet the design standards for spent fuel transport casks, with maximum compression and tensile stresses of 6.89 and 1.37 MPa, respectively, at a testing temperature of -40 °C. In addition, these polymers exhibit effective flame retardancy; combustion ceased within 2 s after removal of the ignition source. All in all, this study provides a simple strategy for preparing rigid polymeric foams, presenting them as promising prospects for application in spent fuel transport casks.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most effective initial device for reducing drag was a full trailer underside cover which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single, dual, and triple axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the Multi-Stage Converging Cavity was introduced which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van-trailer combination.