Small submersible drainage pumps discharge leaking water and rainwater in buildings. In an emergency (e.g., heavy rain or accident), monitoring the flow rate in advance is necessary to enable optimal operation, considering the point where the pump operates abnormally when the water level increases rapidly. In another, pump performance optimization is crucial for energy saving policy. Therefore, it is necessary to meet the challenges of submersible pump systems, including sustainability and pump efficiency. The final goal of this study is to develop an energy-saving, high-efficiency submersible drainage pump capable of responding to emergencies. In particular, this paper targeted the hydraulic performance improvement of a submersible drainage pump model. Before the development of driving mode-related technology capable of emergency response, we first tried to find a way to improve the performance characteristics of the existing submersible drainage pump. Rather than designing a new pump, we disassembled the current pump and reverse engineering. Then, numerical simulation was performed to analyze the flow characteristics and efficiency of the pump. Then, the pump test was carried out to obtain the performance and validated with numerical results. Results revealed that changing the cross-sectional shape of the impeller reduced the flow separation and enhanced velocity and pressure distributions. Also, it reduced the power and increased efficiency. Results also showed that the pump's efficiency increased to 5.56% at a discharge rate of 0.17 m3/min, and overall average efficiency increased to 6.53%. In addition, the submersible pump design method could be suitable for the optimized pump's impeller and casing numerically. This paper can provide insight and information on the design optimization of pumps.

Redox-flow batteries are rechargeable batteries that store energy in two liquid electrolytes, separated by a membrane. During charging and discharging, the electrolytes flow through the membrane and undergo chemical reactions that generate or consume electrical energy. These batteries are known for their scalability and long cycle life and are versatile energy storage technologies developed to enhance efficiency and lower costs. Deep Eutectic Solvents (DES) are eco-friendly alternatives to traditional electrolytes, and their properties have been studied to improve the performance of redox-flow batteries. We investigated choline chloride/ethylene glycol (ChlCl/Eg) mixtures with LiPF6 salt at four concentrations through experimental and MD simulations. The thermophysical and transport properties of the mixture, including density, diffusion coefficient, viscosity, and ionic conductivity, were calculated across a temperature range of 298.15–398.5 K. Our findings indicate that an increase in salt concentration leads to a decrease in diffusion coefficients and ionic conductivity, while increasing the viscosity of the deep eutectic solvent. This research provides valuable insights into the behavior of DES mixtures and can aid in the design and optimization of DES-based processes for use in redox-flow batteries.

In order to balance the conflicts among mass flow rate, total pressure ratio, adiabatic efficiency and stall margin in a low-bypass transonic fan, the optimization of the rotor blade is implemented in this study. An advanced 3D optimization design system is adopted, and flow diagnostic methods based on vorticity dynamics are employed to discuss the flow field. Results indicate that by controlling the blade camber line curvature, significant improvements in the aerodynamic performance for the fan stage are achieved, the total pressure ratio is increased by 1.90%, while the adiabatic efficiency and mass flow rate are increased by 4.45% and 5.82%, respectively. Vorticity diagnosis suggest that there exists a close link between performance parameters and vorticity parameters in the axial fan/compressor, both azimuthal vorticity and boundary vortex flux have significant influences on the stage performance. Moreover, the boundary layer separation is accompanied by the spike of entropy and static pressure, while the derivation/gradient of these flow parameters would also suffer drastic changes under the effect of shock wave. The vorticity parameters could provide detailed flow information about the on-wall flow with high accuracy, which provides the researchers with a novel method for the turbomachinery aerodynamic design and analysis.

Mechanical circulatory support has proven effective in managing postcardiotomy cardiogenic shock by stabilizing patients' hemodynamics and ensuring adequate organ perfusion. Among the available device modalities, the combination of extracorporeal life support and a microaxial flow pump for left ventricular unloading has emerged as a valuable tool in the surgical arma-mentarium. In this publication, we provide recommendations for the application and weaning of temporary mechanical circulatory support in cardiogenic shock patients, derived from a con-sensus among leading cardiac centers in German-speaking countrie

We present a mixing length based algebraic turbulence model calibrated to pipe flow; the main purpose of the model is to capture the increasing turbulence production-to-dissipation ratio observed in connection with the high Reynolds number transition region. The model includes the mixing length description by Gersten and Herwig which takes the observed variation of the von Kármán number with Reynolds number into account. Pipe wall roughness effects are included in the model. Results are presented for area-averaged (integral) quantities which can be used both as a self-contained model and as initial inlet boundary conditions for computational fluid dynamics simulations.

This research delves into the impact of complex low-speed wake flow structures on the aerodynamic characteristics of objects downstream. It employs the proper orthogonal decomposition (POD) method and the domain precursor simulation method to compare traditional methods and validate this approach. The study generates several flow structures of parallel dual-cylinder wakes with different scales and spacing. The variations in the aerodynamic coefficient of three downstream objects at various times passing through wakes of varying scales are appropriately compared and analyzed. The study establishes that the wake with a cylinder spacing of G=1.5 has a more compact and concentrated modal structure than that with a cylinder spacing of G=0.35. Smaller objects are more responsive to the wake flow structure with a spacing of G=1.5, whereas larger objects respond more to the flow structure with a spacing of G=0.35. The achieved results also reveal that the aerodynamic force coefficients of objects passing through the wakefield at different times are closely related to the temporal characteristics of the wake flow structure with different scales.

It is a challenging and meaningful task to carry out drone-based livestock monitoring in high-altitude and cold regions. The purpose of AI is to execute automated tasks and to solve practical problems in actual applications by combining the software technology with the hardware carrier to create integrated advanced devices. Only in this way, the maximum value of AI could be realized. In this paper, a real-time tracking system with dynamic target tracking ability is proposed. It is developed based on the tracking-by-detection architecture using YOLOv7 and DeepSORT algorithms for target detection and tracking, respectively. To address the existing problems of the DeepSORT algorithm, the following two optimizations are made: (1) Optical flow is used to compensate the Kalman filter for improvement of the prediction accuracy; (2) A low-confidence trajectory filtering method is adopted to reduce the influence of unreliable detection on target tracking. In addition, an visual servo controller for the UAV is designed to enable the automated tracking task. Finally, the system is tested using the Tibetan yaks living in the Tibetan Plateau as the tracking targets, and the results reveal the real-time multiple tracking ability and the ideal visual servo effect of the proposed system.

N-acetyl-L-cysteine (NAC), a sulfhydryl-containing compound, is mainly used as a mucolytic and as an antidote for acetaminophen overdose. Flow injection and sequential injection systems were designed and optimized with the aim of providing precise, accurate and reliable flow methods for NAC determination in pharmaceuticals with very low sample and reagent consumption. Proposed methods are based on a redox reaction wherein NAC reduces a complex of Cu(II) and bathocuproine disulfonate (BCS) to orange [Cu(BCS)2]3– complex, which absorption was measured at λmax = 483 nm. The optimized FIA and SIA configuration yielded a linear calibration curve with correlation coefficients (R2 = 0.9999 and R2 = 0.9996) in the concentration range of 3.0 × 10–7 – 3.0 × 10–5 mol L–1 and analytical frequency of 120 h–1 for the FIA method and 4.0 × 10–7 – 4.0 × 10–5 mol L–1, at sampling rate 60 h–1 for the SIA method. The proposed flow methods were successfully applied for the determination of NAC in pharmaceutical products, as the results showed good agreement with the standard method prescribed by Pharmacopoeia. Recoveries were in the range from 98.4% to 101.9% for the FIA method and from 97.2% to 101.8% for the SIA method.

This study investigates the Hagen–Poiseuille pipe flow of viscoplastic fluids, focusing on analytical predictions of concrete pumping using the shear-stress-dependent parabolic model. Research highlights encompass solving the steady laminar pipe flow for viscoplastic fluids described by the parabolic model, extending analytical studies to a nonlinear rheological model with easily accessible experimental parameters, presenting detailed results for the two-fluid parabolic model, and introducing computational apps implementing theoretical findings. The parabolic model outperforms linear models, such as the Bingham model, in accuracy by accounting for the nonlinearity in the shear stress and shear rate relations. The influence of rheological parameters on these relations is analyzed, and their versatility is demonstrated by a Wolfram Mathematica-based application program. This approach is adaptable for other models with shear stress as the independent variable, offering valuable insights into viscoplastic fluid flows.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs > GrO > Gr > C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

An exact solution for the Nagel-Schreckenberg model for v_max = 1 is known since the 90s, yet for v_max > 1 it remains an open question. It is conjectured here that this general solution can be generated from the basic solution (for v_max = 1) by a linear coordinate transformation, the shear mapping, which requires no additional parameters in the deterministic case, and two additional parameters otherwise. The proposed solutions show remarkable agreement with existing numerical solutions, except in the congested regime where the Monte Carlo data shows more concavity than the more linear congested branches predicted by the theory. More research is needed to investigate this bias.

We consider a class of density-driven flow problems. We are particularly interested in the problem of the salinization of coastal aquifers. We consider the Henry saltwater intrusion problem with uncertain porosity, permeability, and recharge parameters as a test case. The reason for the presence of uncertainties is the lack of knowledge, inaccurate measurements, and inability to measure parameters at each spatial or time location. This problem is nonlinear and time-dependent. The solution is the salt mass fraction, which is uncertain and changes in time. Uncertainties in porosity, permeability, recharge, and mass fraction are modeled using random fields. This work investigates the applicability of the well-known multilevel Monte Carlo (MLMC) method for such problems. The MLMC method can reduce the total computational and storage costs. Moreover, the MLMC method runs multiple scenarios on different spatial and time meshes and then estimates the mean value of the mass fraction. The parallelization is performed in both the physical space and stochastic space. To solve every deterministic scenario, we run the parallel multigrid solver ug4 in a black-box fashion. We use the solution obtained from the quasi-Monte Carlo method as a reference solution.

The main target of this study was to evaluate the impact of future climate change on the available surface water resources in the Dhidhessa Sub-basin, Abbay Basin, Ethiopia. For the prediction, high-resolution Regional Climate Models (RCMs) from multiple climate models with data from Representative Concentration Pathways (RCPs) prepared by the CCAFS were used. The predictions of future discharge (stream flow) were based on climate scenarios data of baseline period of 1991 to 2020 and for the future with two time windows, 2044 (2030–2059) and 2084 (2070–2099), on a monthly time step after bias correction was conducted to both precipitation and temperature in the future climate under each RCP scenario. After sensitivity analysis, calibration (1994–2011), and validation (2012–2020) of the model for the Dhidhessa Sub-basin with the SUFI-2 program in the SWAT-CUP model, the SWAT model was used to determine water balance and stream flow from the SWAT model system. The SWAT model performed well in predicting stream flow in the Dhidhessa Sub-basins, with a coefficient of determination (R2) ranging from 0.8 to 0.94 and a Nash Sutcliffe value (NSE) ranging from 0.76 to 0.89. The percent decrease in mean annual stream flow from 2044 and 2084 were 10 %, in 2044, and 6.3% in 2084 respectively. The seasonal result under short-term 2044 of stream flow present change significantly decreased in spring, winter, and autumn with 20.2%, 67.4%, and 67.4% respectively. While summer season increased by 43.1%, under short-term 204. In long-term 2084 percent change declined except summer seasons, with 14.7%, 58.1%, and 3.3%, change in spring, winter, and autumn, respectively, and summer, with 51.1% increased and With RCP4.5 (1.64%) and RCP8.5 (2.1%) changed. In the future Dhidhessa stream flow increases and decreases from the baseline era. The decreasing stream flow in 2044 and 2084 will negatively affect agricultural production. This study revealed that any effect on this river resulting in a drop in flow will have a direct impact on ongoing water resource development and socio-economic development of the area.

In the diagnosis of olfactory neuroblastoma (ONB), the presence of S-100–positive sustentacular cells surrounding the tumor is important; however, these are also present in normal nasal sinus epithelium. Although ONB often has a different final diagnosis, complete resection of the tumor has a good prognosis and minimally affects the patient's treatment plan. When the tumor extends around the internal carotid artery (ICA), complete resection is difficult due to the high risk of vascular injury; revascularization using a high-flow bypass can avoid this complication. In the present case, the tumor was located in the left sphenoid sinus and extended around the ICA. Preoperative biopsy tissue was positive for neuroendocrine markers and slightly positive for S-100 protein, leading to a diagnosis of ectopic ONB. High-flow bypass revascularization with trapping of the ICA allowed complete tumor resection. The postoperative histopathological diagnosis was neuroendocrine carcinoma, showing no S-100 protein–positive cells. There was no sign of recurrence two and a half years after surgery without additional treatment. This case demonstrates that the presence of S-100 protein–positive cells in ONB may be misleading. Although misdiagnosis of ectopic ONB should be anticipated, a complete resection of the tumor is an effective treatment strategy.

In this paper after introducing a model of binary data matrix (BDM) for physical parameters of an evolving system (of particles), we develop a Hilbert space as an ambient space to derive induced metric tensor on embedded parametric manifold identified by associated joint probabilities of particles observables (parameters). Parameter manifold assumed as space-like hypersurface evolving along time axis, an approach that resembles 3+1 formalism of ADM and numerical relativity. We show the relation of endowed metric with related density matrix. Identification of system density matrix by this metric tensor, leads to the equivalence of quantum Liouville equation and metric compatibility condition while covariant derivative of metric tensor has been calculated respect to Wick rotated time or spatial coordinates. After deriving a formula for expected energy per particles, we prove the equality of this expected energy with local scalar curvature of related manifold. We show the compatibility of BDM model with Hamilton-Jacobi formalism and canonical forms. On the basis of the model, I derive the Ricci flow like dynamics as the governing dynamics and subsequently derive the action of BDM model and Einstein field equations. Given examples clarify the compatibility of the results with well-known principles such as equipartition energy principle and Landauer’s principle. This model provides a background for geometrization of quantum mechanics compatible with curved manifolds and information geometry. Finally, we conclude a “bit density principle” which predicts the Planck equation, De Broglie wave particle relation, , Beckenstein bound and Bremermann limit.

As a consequence of the increasing share of renewable energies and sector coupling technologies, new approaches are needed for the study, planning, and control of modern energy systems. Such new structures may add extra stress to the electric grid, as is the case with heat pumps and electrical vehicles. Therefore, the optimal performance of the system must be estimated considering the constraints imposed by the different sectors. In this research, a dispatch optimization method with an iterative grid constraint generation, decoupled from the linear unit commitment problem, is employed. From the considered scenarios, it was found that in a typical German neighborhood with 150 households, PV penetration of ∼5kWp per household can lead to curtailment of ∼60MWh per year due to line loading. Furthermore, the proposed method eliminates grid violations due to the addition of new sectors reducing the curtailment up to 60%. With the optimization of the heat pump operation, an increase of 7% of the self-consumption was achieved with similar results for the combination of battery systems and electrical vehicles. In conclusion, a safer and optimal operation of a complex energy system is fulfilled. Safer control strategies and more accurate plant sizing could be derived from this work.

Autonomous systems require identifying the environment and it has a long way to go before putting it safely into practice. In autonomous driving systems, the detection of obstacles and traffic lights are of importance as well as lane tracking. In this study, an autonomous driving system is developed and tested in the experimental environment designed for this purpose. In this system, a model vehicle having a camera is used to trace the lanes and avoid obstacles to experimentally study autonomous driving behavior. Convolutional Neural Network models were trained for Lane tracking. For the vehicle to avoid obstacles, corner detection, optical flow, focus of expansion, time to collision, balance calculation, and decision mechanism were created, respectively.

According to the Water Framework Directive, the Ecological Flow (Eflow) is assumed to be the minimum water discharge required to achieve and maintain the environmental objectives of “good quality status” in a natural water body. It is highly recognized that, the hydrological regime of natural flow plays a primary and crucial role influencing the physical conditions of habitats, which in turn determines the biotic composition and sustainability of aquatic ecosystems. Furthermore, the simple assumption to supply a minimum instream during dry periods is not enough any longer in order to protect the river environment. The recent hydro-ecological understanding states that all flow components might be considered as operational targets for water management, starting from base flows (including low flows) to high and flood regimes in terms of magnitude, frequency, duration, timing and rate of change. Several codes have been developed and applied on different case studies in order to define common tools to be implemented for the Eflow assessment. The study proposes the application of the Indicators of Hydrologic Alteration methodology (IHA by TNC) coupled to the valuation of the Index of Hydrological Regime Alteration (IARI by ISPRA) as an operative tool to define the ecological flow in each monitoring cross section to support the sustainable water resources management and planning. The case study of Agri River, in Basilicata (Southern Italy) is presented. The analyses have been carried out on monthly discharge data derived applying the HEC-Hydrological Modelling System at the basin scale using the daily rain data measurements obtained by the regional rainfall gauge stations and calibrated through the observed inlet water discharge registered at the Lago del Pertusillo reservoir station.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Beta-glucan-stimulated mammalian macrophages show an increased responsiveness to secondary stimulation in a nonspecific manner. This phenomenon is known as trained innate immunity. Our study aimed to explore training of primary chicken monocytes. We hypothesized that primary chicken monocytes, similar to their mammalian counterparts, can be trained with β-glucan resulting in increased responses of these cells to a secondary stimulus. Primary blood monocytes of white leghorn chickens were primary stimulated with β-glucan microparticulates (M-βG), LPS, recombinant chicken interleukin-4 (IL-4) or combinations of these components for 48 h. On day 6, the primary stimulated cells were secondary stimulated with LPS. Nitric oxide (NO) production levels were measured as an indicator of pro-inflammatory activity. In addition, the cells were analysed by flow cytometry to characterize the population of trained cells and to investigate the expression of surface markers associated with activation. After the secondary LPS stimulation, surface expression of CSF1R and the activation markers CD40 and MHC-II was higher on macrophages that were trained with a combination of M-βG and IL-4 compared to unstimulated cells. This increased expression was paralleled by enhanced NO production. In conclusion, this study showed that trained innate immunity can be induced in primary chicken monocytes with β-glucan, which is in line with previous experiments in mammalian species. Innate immune training may have potential to improve health and vaccination strategies within the poultry sector.

Transition between free-surface and pressurized flows is an crucial phenomenon in many hydraulic systems, including water distribution systems, urban drainage systems, etc. During the transition, the force exerted on the structures changes drastically, thus it is meaningful to simulate this process. However, severe numerical oscillations are widely observed behind filling-bores, causing unphysical pressure variations and even computation failure. In this paper, some oscillation-suppressing approaches are reviewed and evaluated on a benchmark model. Then a new oscillation-suppressing approach is proposed to admit numerical viscosity when the water surface is at proximity of conduct roof which has first order accuracy. This approach adds numerical viscosity when water surface is at the proximity of conduct roof. It can sufficiently suppress numerical oscillations under an acoustic wave speed of 1000m/s and is simple to apply. In comparison with two experiments, the simulation results of this method show good agreement and little numerical oscillations. The results in this paper can help readers to choose an appropriate oscillation-suppressing method to improve the robustness and accuracy of flow regime transition simulations.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

In this article, we describe an immunochromatographic test system developed for rapid serodiagnostics of cattle brucellosis using two markers: gold nanoparticles (GNPs) and quantum dots (QDs). The test system was compared with immunochromatographic serodiagnostics systems that use only one marker. The approbation of the test system was conducted on samples of cattle sera with low, but diagnostically significant titers of specific antibodies. We show that when two conjugates are used, the intensity of the detectable signal increases by 2–3 times compared with the test system using the QD conjugate and by more than 9 times compared with the system using the GNP conjugate.

This work aims to develop an integrated fault location and restoration approach for microgrids (MGs). This work contains two parts. Part I presents the fault location algorithm, and Part II shows the restoration algorithm. The proposed algorithms are implemented by particle swarm optimization (PSO). The fault location algorithm is based on network connection matrices, which are the modifications of bus-injection to branch-current and branch-current to bus-voltage (BCBV) matrices, to form the new system topology. The backward/forward sweep approach is used for the prefault power flow analysis. After the occurrence of fault, the voltage variation at each bus is calculated by using the Zbus modification algorithm to modify Zbus. Subsequently, the voltage error matrix is computed to search for the fault section by using PSO. After the allocation of the fault section, the multi-objective function is implemented by PSO for optimal restoration with its constraints. Finally, the IEEE 37-bus test system connected to distributed generations is utilized as the sample system for a series simulation and analysis. The outcomes demonstrated that the proposed optimal algorithm can effectively solve the fault location and restoration problem in MGs.

Present study offers mathematical calculations of the roll-coating procedure lubricated with upper Convected Maxwell Fluid. An incompressible isothermal viscoelastic fluid is considered with roll and the porous web having uniform velocities. By employing Lubrication Approximation Theory, the desired equations of motion for the fluid concerned over porous web are modelled and analyzed. The suction rate on the web and injection rate at the roll surface are anticipated proportionate. Results for velocity profile and pressure gradient are obtained analytically. Fluid parameters of industrial significance i.e. detachment point, pressure, sheet /roll separating force, power contribution and coating thickness are also calculated numerically. Substantial and monotonic increase is witnessed in these quantities with the increase of flow parameters.

Flow field based methods are becoming increasingly popular for the analysis of interfacial shear rheology data. Such methods take properly into account the subphase drag by solving the Navier-Stokes equations for the bulk phases flows, together with the Boussinesq-Scriven boundary condition at the fluid-fluid interface, and the probe equation of motion. Such methods have been successfully implemented at the double wall-ring (DWR), the magnetic rod (MR), and the bicone interfacial shear rheometers. However, a study of the errors introduced directly by the numerical processing is still lacking. Here we report on a study of the errors introduced exclusively by the numerical procedure corresponding to the bicone geometry at an air-water interface. In our study we directly input a preset the value of the complex interfacial viscosity and we numerically obtain the corresponding flow field and the complex amplitude ratio for the probe motion. Then we use the standard iterative procedure to obtain the calculated complex viscosity value. A detailed comparison of the set and calculated complex viscosity values is made upon changing different parameters such as real and imaginary parts of the complex interfacial viscosity and frequency. The observed discrepancies yield a detailed landscape of the numerically introduced errors.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

In this study, regression analyses were used to find a relationship between the rain gauge rainfall rate R and radar reflectivity Z for the urban catchment of the Służewiecki Stream in Warsaw, Poland. Rainfall totals for 18 events which were measured at two rainfall stations were used for these analyses. Various methods for determining calculational values of radar reflectivity in reference to specific rainfall cells with 1-km resolution within an event duration were applied. The influence of each of these methods on the Z-R relationship was analyzed. The correction coefficient for data from the SRI (Surface Rainfall Intensity) product was established, in which the values of rainfall rate are calculated based on parameters a and b determined by Marshall and Palmer. Relatively good agreement between measured and estimated rainfall totals for the analyzed events was obtained using the Z-R relationships as well as the correction coefficient determined in this study. Rainfall depths estimated from radar data for two selected events were used to simulate flow hydrographs in the catchment using the SWMM (Storm Water Management Model) hydrodynamic model. Different scenarios were applied to investigate the stream response to changes in rainfall depths, in which the data both for 2 existing as well as 64 virtual rain gauges assigned to appropriate rainfall cells in the catchment were included.

The increasing use of renewable energies as a source of electricity has led to a fundamental transition of the power supply system. The integration of fluctuating weather-dependent energy sources into the grid already has a major impact on the load flows of the grid. As a result, the interest in forecasting wind and solar radiation with a sufficient accuracy over short time horizons grew. In this study the short-term forecast of the effective cloud albedo based on optical flow estimation methods are investigated. The optical flow method utilized here is TV-L¹ from the open source library OpenCV. This method uses a multi-scale-approach to capture cloud motions on various spatial scales. After the clouds are displaced the solar surface radiation will be calculated with SPECMAGIC NOW which computes the global irradiation spectrally resolved from satellite imagery. Due to a high temporal and spatial resolution of satellite measurements the effective cloud albedo and thus solar radiation can be forecasted from 5 minutes up to 4 hours with a resolution of 0.05°. In the following there will be a brief description of the method for the short-term forecast of the effective cloud albedo. Subsequently evaluation results will be presented and discussed. Finally an outlook of further developments will be given.

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

Based on the goals of "high reliability, high frequency, rapid launch, and low cost" for space launch site, and drawing inspiration from the design principles of SpaceX's Starship launch test facility, an integrated dual-sided deflector system for convective cooling and thermal protection is presented. The interaction process between the gas jet and liquid water jet and its effect on the flow field environment are thoroughly studied using numerical calculation methods. Furthermore, Regarding the phase-change heat transfer issue in a compressible gas-liquid two-phase flow and the varying distribution of different bubble shapes and sizes at the gas-liquid interface, a modified Lee model is derived. The rationality and accuracy of the phase-change mass-transfer coefficient values can be improved by adjusting the equivalent diameter and shape factor of the bubbles. The research results demonstrate that compared to the classical Lee model, the modified Lee model can achieve a higher numerical accuracy in predicting the heat and mass transfer processes in gas-liquid two-phase flows. Through comparative analysis with traditional dual-sided deflector and conventional cooling system, the integrated dual-sided deflector system for convective cooling and thermal protection exhibits significant performance advantages in gas flow regulation, flow field environment improvement and erosion protection in the near-ground region of the launch site. Particularly, regarding the thermal environment of the dual-sided deflector, it not only achieves effective flow deflection, but also mitigates the degree of erosion caused by the gas jet on the deflector. This conclusion can provide theoretical references for the thermal protection design of commercial launch vehicle system at space launch site.

Keywords: Echocardiographic alterations; left ventricle; dog; Trypanosoma cruzi; flow patterns; dilated cardiomyopathy; Chagas disease

The C-C motif chemokine receptor 8 (CCR8) is highly and selectively expressed in regulatory T (Treg) cells and is associated with tumor progression. The massive accumulation of Treg cells into tumors suppresses the effector function of CD8⁺ cells against tumor cells. Therefore, selective depletion of Treg cells using anti-CCR8 monoclonal antibodies (mAbs) reinvigorates antitumor immune responses and improves responses to cancer immunotherapy. Previously, we developed an anti-mouse CCR8 (mCCR8) mAb, C₈Mab-2, using the Cell-Based Immunization and Screening (CBIS) method. In this study, the binding epitope of C₈Mab-2 was investigated using flow cytometry. The mCCR8 extracellular domain-substituted mutant analysis showed that C₈Mab-2 recognizes the N-terminal region (1–33 amino acids) of mCCR8. Next, 1×alanine (or glycine) scanning and 2×alanine (or glycine) scanning were conducted in the N-terminal region. The results revealed that the _17-DFFTAP_-22 sequence is important for the recognition by C₈Mab-2, and Thr20 is a central amino acid of the epitope. These results revealed the involvement of the N-terminus of mCCR8 in the recognition by C₈Mab-2.

Oxidoreductase (OXR) enzymes are in high demand for biocatalytic applications in food industry and cosmetics: glucose oxidase (GOx), cellobiose dehydrogenase (CBDH), bioremediation: horseradish peroxidase (HRP), laccase (LAC), and medicine for biosensors and miniature biofuel cells (GOx, CBDH, LAC, HRP). They can be used in a soluble form and/or within the yeast cell walls expressed as chimeras on the surface of yeast cells (YSD), such as P. pastoris and S. cerevisiae. However, most of the current studies suffer from either low yield for soluble enzyme expression or low enzyme activity when expressed as chimeric proteins using YSD. This is always the case in studies dealing with heterologous expression of oxidoreductase enzymes, since there is requirement not only for multiple OXR genes integrations into the yeast genome (super transformations), and codon optimization, but also very careful design of fermentation media composition, and fermentation conditions during expression due to need for adding transition metals (copper, iron), and metabolic precursors of FAD and heme. Therefore, scientists are still trying to find optimal formula using above mentioned approaches, and most recently also using protein engineering and directed evolution for additional increase in the yield of recombinant enzyme production. In this review article we will cover all the current state of the art technologies and most recent advances in the field that yielded high expression level for some of these enzymes in specially designed expression/fermentation systems. We will also tackle and discuss new possibilities for further increase in fermentation yield by the cutting-edge technologies such are directed evolution, protein and strain engineering, high-throughput screening methods based on in vitro compartmentalization, flow cytometry and microfluidics.

Malaria is rare in Europe, but it is a medical emergency and programs for its control should ensure access to early diagnosis and prompt treatment within 24-48 h of the symptom’s onset. The consistent number of imported malaria cases and the risk of reappearance of autochthonous cases stimulated laboratories in non-endemic countries to evaluate diagnostic methods/algorithms: microscopy remains the gold standard, but with limitations. RDTs have greatly expanded the ability to diagnose malaria for rapid results due to simplicity and low cost, but they lack sensitivity and specificity. PCR-based assays provide more relevant information but need well-trained technicians. According to WHO global Technical Strategy for Malaria 2016-2030, the future direction for a rapid diagnosis is the development of Point-Of-Care Testing, which would be helpful for prompt/accurate treatment and for preventing the diseases spread. Despite the limitations of current diagnostic methods, they play important roles in dealing with the global malaria situation, including decreasing its incidence. Recently evidence suggested that Artificial Intelligence could be utilized for assisting pathologists in malaria diagnosis. Future studies need to be conducted to see whether this system can be used for routine malaria diagnostic procedures.

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

Progressive loss of retinal ganglionic cells (RGC) causes blindness in glaucoma. Elevated intraocular pressure (IOP) is the most important, treatable risk factor. Currently, the management of glaucoma is centred at reducing the IOP, and drugs in the form of topical drops are the first line of management. Drugs reduce IOP either by suppressing aqueous humour secretion or improving the aqueous humour outflow. Newer drugs added during the past three decades to the armamentarium of glaucoma treatment have targeted the aqueous outflow. With an evolving understanding of the pathogenesis of glaucoma, the role of 24-hour IOP control and other IOP-independent risk factors affecting ocular blood flow and RGC toxicity is also recognised. The role of available drugs in controlling IOP over 24-hours is being evaluated. Improvement of ocular blood flow and neuroprotection are seen as potential drug targets in preventing the loss of RGC. In this article, we review the pharmacotherapy of glaucoma based on current therapeutic principles.

Employing numerical methods to simulate manufacturing processes and study their influential factors is increasing. The development of computers and engineering software has increased the ability and accuracy of numerical methods in simulating various aspects of different processes. One of the manufacturing processes that has been considered by many industries in recent years to join metals in solid-state with unique properties is called friction stir welding. It is challenging and, in some cases, impossible to experimentally study the various aspects of this process, such as temperature distribution, stress distribution, and material flow, due to severe plastic deformation in the weld zone. In this case, numerical methods are used to investigate these parameters and better understand the process. This study first investigates various numerical methods researchers use to simulate the process. The ability, pros, and cons of these methods to simulate the process are also examined. Then, the applications of numerical models in simulating the temperature distribution during the process as well as the effects of input parameters on the temperature history of the process, are deeply considered. Next, the application of numerical methods in material flow modeling during the process is investigated. Finally, the modeling of the microstructure of the welding zone is investigated using numerical methods that help significantly in predicting the weld microstructure.

Glycerol has found its applications as a heat-transfer fluid in heat exchangers, and as a compo-nent of functional solutions in biosensor analysis. Flowing non-aqueous fluids are known to be able to induce electromagnetic fields due to triboelectric effect. These triboelectrically generated electromagnetic fields can affect biological macromolecules. Horseradish peroxidase (HRP) is widely employed as a convenient model object for studying how external electric, magnetic, and electromagnetic fields affect enzymes. Herein, we have studied whether the flow of glycerol in a ground-shielded cylindrical coil affects the HRP enzyme incubated at a 2 cm distance near the coil’s side. Atomic force microscopy (AFM) has been employed in order to study the effect of glycerol flow on HRP at the nanoscale. Increased aggregation of HRP on mica has been observed after the incubation of the enzyme near the coil. Moreover, the enzymatic activity of HRP has also been affected. The results reported can find their application in biotechnology, food technology and life sciences application, considering the development of triboelectric generators, en-zyme-based biosensors and bioreactors with surface-immobilized enzymes. Our data can also be of interest for scientists studying triboelectric phenomena.

For effective warehouse management, various criteria should be taken into consideration in terms of inventory management, demand, transportation distance, usage area, delivery-waiting times, and minimizing the costs that may arise from them. Because, the purpose of the product assignment problem is to minimize the total transport distance during storage and to reduce the space required for product assignment. However, the storage location assignment problem (SLAP) occurs simultaneously with production planning activities in real life. In this study, an integrated mixed-integer nonlinear (MINLP) mathematical model is proposed, which includes the assignment of products to storage areas and production planning, using the TOPSIS (Technique for Order Preference by Similarity to Ideal Solution) class based policy for storage systems where multiple criteria are important. In the TOPSIS class-based policy, weight and waiting time criteria are taken into account, as well as the COI (Cube-per-order index index), which is widely used in the literature. In addition, a decision support system flow has been proposed that takes into account the single criterion, multiple criteria and COI index criteria of the developed model and provides its integration with different product assignment policies. Detailed literature research; It has been revealed that the proposed mathematical model and decision support system flow have the feature of applying an existing field of science to a new problem.

Cryptococcosis is one of the most serious opportunistic diseases in patients living with HIV. For this reason, it is important to have early diagnosis and appropriate treatment. Objectives. The aim of the study was to know the evolution of patients diagnosed with cryptococcosis by detection of Cryptococcus antigen in serum by lateral flow (CrAg LFA) without nervous system involvement and with treatment in accordance with the results. Materials and Methods. A retrospective, longitudinal, analytical study was performed. Seventy patients with cryptococcosis initially diagnosed by serum CrAg LFA without meningeal involvement between January 2019 and April 2022 were analyzed for medical records. The treatment regimen was adapted to the results of blood culture, respiratory material or pulmonary tomography imaging. Results. Seventy patients were included, 13 had probable pulmonary cryptococcosis, 4 had proven pulmonary cryptococcosis, 3 had fungemia and 50 had pre-emptive therapy without microbiological or imaging findings compatible with cryptococcosis. Among the 50 patients with pre-emptive therapy, none had meningeal involvement or cryptococcosis recurrences to date. Conclusion. Pre-emptive therapy avoided progression to meningitis in patients with CrAg LFA-positive patients. Pre-emptive therapy with dose adjustment of fluconazole in patients with the mentioned characteristics was useful despite the use of lower doses than recommended.

In a power plant that uses seawater as a coolant, a debris filter is required to remove foreign substances from the seawater, and differential pressure leads to a decrease in the coolant flow rate, leading to a decrease in power generation efficiency. In this study, analysis was performed under different initial flow velocity conditions of 1.5m/s, 2.0m/s, and 2.5m/s for a debris filter used in a power plant to understand flow characteristics in CTCS. The flow and differential pressure characteristics of a CTCS with an installed debris filter were considered in a comparative analysis of velocity, pressure, and turbulent kinetic energy distribution. The results confirmed that a vortex was generated in the pipe with the debris filter, apparently due to the collision of the flow with the bracket of the debris filter. As the flow rate increased, the range of the vortex increased, causing a loss in flow.

The passenger prediction flow is very significant to transportation sustainability. This is due to some chaos of traffic jams encountered by the road users during their movement to the offices, schools, or markets at earlier of the days and during closing periods. This problem is peculiar to the transportation system of the Federal University of Technology Minna, Nigeria. However, the prevailing technique of passenger flow estimation is non-parametric which depends on the fixed planning and is easily affected by noise. In this research, we proposed the development of a hybrid intelligent passenger frequency prediction model using the Auto-Regressive Integrated Moving Average (ARIMA) linear model, Convolutional Neural Network (CNN), and Kalman Filter Algorithm (KFA). The passengers’ frequency of arrival at the bus terminals is obtained and enumerated through the closed-circuit television (CCTV) and demonstrated using the Markovian Queueing Systems Model (MQSM). The ARIMA model was used for learning and prediction and compared the result with the combined techniques of using CNN-KFA. The autocorrelation coefficient functions (ACF) and partial autocorrelation coefficient functions (PACF) are used to examine the stationary data with different features. The performance of the models was analyzed and evaluated in describing the short-term passenger flow frequency at each terminal using the Mean Absolute Percentage Error (MAPE) and Mean Squared Error (MSE) values. The CNN-Kalman-filter model was fitted into the short-term series and the MAPE values are below 10%. The Mean Square Error (MSE) shows that the CNN-Kalman Filter model has the overall best performance with 83.33% of the time better than the ARIMA model and provides high accuracy in forecasting.

Detailed flow distributions in vascular systems are the key to identifying hemodynamic risk factors for the development and progression of vascular diseases. Although computational fluid dynamics (CFD) has been widely used in bioengineering research on hemodynamics predictions, not only are high-fidelity CFD simulations time-consuming and computing-expensive, but also not friendly to clinical applications due to the difficulty of comprehensive numerical calculations. Machine learning (ML) algorithums to estimate the flow field in vascular systems based on the angiographic images of the blood flow using existed diagnostic tools are emerging as a new pathway to facilitate the mapping of hemodynamics. In present work, the dye injection in a water flow was simulated as an analogy of the contrast perfusion in blood flow using CFD. In the simulation, the light passes through the flow field and generates projective images, as an analogy of X-ray imaging. The simulations provide both the ground truth velocity field and the projective images of the flow with dye patterns. A rough velocity field was estimated using the optical flow method (OFM) based on projective images. ML algorithums are then trained using the ground truth CFD data and the OFM velocity estimation as the input. Finally, the interpretable (logistic regression) and deep (neural networks, convolutional neural networks, long short term memory) machine learning models are validated by using parallel in vitro experiments on the same flow setup. The validation results showed that the employed ML model significantly reduced the error rate from 53.5% to 2.5% in average for the v-velocity estimation.

The role of agricultural transport costs in core-periphery structures has habitually been ignored in New Economic Geography (NEG) models. This is due to the convention of treating the agricultural good as the numéraire, thus implying that agricultural transportation costs are assumed to be zero in these models. For more than three decades, this has been the standard setting in spatial equilibrium analysis. The paper examines the effects of agricultural transport costs on the spatial organisation of regional structures in Peru. In doing so, the Krugman’s formulation of iceberg transport costs is modified to introduce the agricultural transport costs into the dynamic of the NEG models. We use exploratory spatial flow data analysis methods and non-spatial and spatial origin-destination flow models to explore how the regional spatial structure change when real transportation data for agricultural goods is included into the iceberg transport costs formulation. We show that agricultural transport costs generate flows that are systematically associated with flows to or from nearby regions generating thus the emergence of spatial spillovers across Peruvian regions. The results of the paper support the contention that NEG models have overshadowed the role of agricultural transport costs in determining the spatial configuration of economic activities.

Steady-state Reynolds-Averaged Navier-Stokes (RANS) simulations are performed for a leading-edge inflatable wing for airborne wind energy applications. Expanding on previous work where only the inflatable leading edge tube was considered, eight additional inflatable strut tubes that support the wing canopy are now included. The shape of the wing is considered to be constant. The influence of the strut tubes on the aerodynamic performance of the wing and the local flow field is assessed, considering flow configurations with and without side-slip. The simulations show that the aerodynamic performance of the wing decreases with increasing side-slip component of the inflow. On the other hand, the chordwise struts have little influence on the integral lift and drag of the wing, irrespective of the side-slip component. The overall flow characteristics are in good agreement with previous studies. In particular, it is confirmed that at a low Reynolds number of Re=10^5, a laminar separation bubble exists on the suction side of this hypothetical rigid wing shape with perfectly smooth surface. The destruction of this bubble at low angles of attack impacts negatively on the aerodynamic performance.

Population growth and increasing global demand for freshwater have raised a serious challenge for the depleting sources of freshwater in the 21st century. Desalination technologies can be a reliable technique for providing freshwater. Capacitive deionization is one of the innovative desalination methods that has received increasing interest. Flow-electrode capacitive deionization (FCDI) (a new architecture of capacitive deionization) is one of the efficient, cost-effective, and environmentally-friendly desalination methods for freshwater production. In this experimental research, the performance of an FCDI system was investigated and the influence of important parameters such as flow rate of flow-electrodes, electrolyte salt concentration of flow-electrodes, and initial feed water concentration will be assessed on the efficiency of desalination operation. In this study, the flow-electrodes operated in short-circuited closed-cycle operation (SCC) mode, and also the feed water operated similarly to the flow-electrodes in closed-cycle. Moreover, in all the experiments, the salt adsorption capacity (SAC) and salt removal efficiency (SRE) was calculated. Herein, by optimizing the above mentioned parameters, the salt removal efficiency of 83% and a SAC value of 29.12 mg/g dry carbon were achieved in 5 hours.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

Non-genuine medical products, including diagnostic devices, have become a lucrative business for fraudsters, causing significant damage to revenues and reputation of companies, as well as posing a significant risk to the health of people and societies. Along a “digital twin” representing centrifugal microfluidic flow control on exemplary “Lab-on-a-Disc” (LoaD) systems, a novel, two-pronged strategy to safeguard miniaturized point-of-care devices by means of secret features and manufacturing challenges is outlined; such “hardware encryption” is flexibly programmed for each chip during production, and deciphered from a secure, local or online database at the time of use. This way, unlicensed copying may be efficiently deterred by an unfavourable economy-of-scale, even in absence of legal prosecution.

Accurate forecasts of ocean waves energy can not only reduce costs for investment but it is also essential for management and operation of electrical power. This paper presents an innovative approach based on the Long Short Term Memory (LSTM) to predict the power generation of an economical wave energy converter named “Searaser”. The data for analyzing is provided by collecting the experimental data from another study and the exerted data from numerical simulation of searaser. The simulation is done with Flow-3D software which has high capability in analyzing the fluid solid interactions. The lack of relation between wind speed and output power in previous studies needs to be investigated in this field. Therefore, in this study the wind speed and output power are related with a LSTM method. Moreover, it can be inferred that the LSTM Network is able to predict power in terms of height more accurately and faster than the numerical solution in a field of predicting. The network output figures show a great agreement and the root mean square is 0.49 in the mean value related to the accuracy of LSTM method. Furthermore, the mathematical relation between the generated power and wave height was introduced by curve fitting of the power function to the result of LSTM method.

To sustain water-dependent economic and socio-ecological systems, natural capital and its interactions with other capitals is gaining attention, but a clear understanding of how to manage natural capital sustainably and how to make decisions relevant to water-related ecosystem services is yet to be achieved. In this study, we extended the framing of water-related ecosystem service flows as a cycle, integrating water quantity and quality and capturing the flows of ecosystem services (i.e., green phase) and ecosystem disservices (i.e., red phase), and connecting natural capital, built capital, and beneficiaries. We applied this framework to the Jiulong River watershed in China, using hydrological models to model water quantity and quality based on historical observations and experimental data. Our results showed that, during the green phase, the interactions of natural capital and built capital significantly improved water quality in downstream areas with higher flows. During the red phase, built capital reduced ecosystem disservices by ~10% while natural capital further reduced it by over one half. Our framework can provide information for natural capital management, eco-compensation, and pollutant management relevant to water-related ecosystem services.

Using only a limited number of computationally expensive functions, we show a way how to construct accurate and computationally efficient approximations of the Colebrook equation for flow friction. The presented approximations are based on the asymptotic series expansion of the Wright ω-function and symbolic regression. The results are verified with 8 million of Quasi-Monte Carlo points covering the domain of interest for engineers. In comparison with the built-in “wrightOmega” feature of Matlab R2016a, the herein introduced related approximations of the Wright ω-function significantly accelerate the computation. With only two logarithms and several basic arithmetic operations used, the presented approximations are not only computationally efficient but also extremely accurate. The maximal relative error of the most promising approximation which is given in the form suitable for engineers’ use is limited to 0.0012%, while for a little bit more complex variant is limited to 0.000024%.

A portable urea sensor for use in the fast flow condition was fabricated using porous polytetrafluoroethylene (PTFE) membranes coated with amine-functionalized parylene, parylene-A, by vapor deposition. To generate a specific electrochemical sensor signal from urea, the urea-hydrolyzing enzyme urease was immobilized on the parylene-A-coated PTFE membranes via chemical crosslinking using glutaraldehyde. The urease-immobilized membranes were assembled in a polydimethylsiloxane (PDMS) fluidic chamber, and a screen-printed carbon three-electrode system was used for electrochemical measurements. The success of urease immobilization was confirmed using fluorescence microscopy, scanning electron microscopy, and Fourier-transform infrared spectroscopy. The optimum concentration of urease for immobilization on the parylene-A-coated PTFE membranes was determined to be 48 mg/mL, and the optimum number of membranes in the PDMS chamber was found to be 8. Using these optimized conditions, we fabricated the urea biosensor and monitored urea samples under various flow rates ranging from 0.5 to 10 mL/min in the flow condition using chronoamperometry. To test the applicability of the sensor for physiological samples, we used it for monitoring urea concentration in the waste peritoneal dialysate of a patient with chronic renal failure, at a flow rate of 0.5 mL/min.

Ongoing climate change causes abnormal climate events worldwide such as increasing temperatures and changing rainfall patterns. With South Korea facing growing damage from the increased frequency of localized heavy rains, the country is not an exception. In particular, its steep slope lands, including mountainous areas, are vulnerable to damage from landslides and debris flows. In addition, localized short-term heavy rains that occur in urban areas with extremely high intensity tend to lead a sharp increase in damage from soil-related disasters and cause huge losses of life and property. Currently, South Korea predicts landslides and debris flows using the standards for forecasting landslides and heavy rains. However, as the forecasting is conducted separately for rainfall intensity and accumulated rainfall, this lacks a technique that reflects both amount and intensity of rainfall in an episode of localized heavy rainfall. This study, therefore, aims to develop such a technique by collecting past cases of debris flow occurrences and rainfall events that accompanied debris flows to calculate the rainfall triggering index (RTI) reflecting accumulated rainfall and rainfall intensity. In addition, the RTI is converted into the critical accumulated rainfall (Rc) to use precipitation information and provide real-time forecasting. The study classifies the standards for flow debris forecasting into three levels: ALERT (10%–50%), WARNING (50%–70%), and EMERGENCY (70% or higher), to provide a nomogram for 6 hr, 12 hr, and 24 hr. As a result of applying this classification into the actual cases of Seoul, Chuncheon, and Cheongju, it is found that about 2–4 hr of response time is secured from the point of the Emergency level to the occurrence of debris flows.

The microstructures and mechanical properties of the hot-rolled Fe-6.5wt.%Si sheet are analyzed. The microstructure of the hot-rolled sheet is layered along the thickness direction. The surface exhibits fine and equiaxed grains, whereas the center part shows coarse and elongated grains with a <101> fiber texture along the rolling direction. Serrated flow behavior is observed during tensile deformation of both the hot-rolled sheet and its center samples at 350 °C; thus, the serrated flow of the hot-rolled sheet is mainly attributed to the serration of the center part. The analyses of dislocation configurations, ordered structures, and crystal orientation show that the serrated flow behavior results from the interaction of solutes with mobile dislocations. Mobile dislocations are pinned by combining parallel forest dislocations with the pipe diffusion of solution atoms. This study provides a new perspective for the deformation mechanism of the Fe-6.5wt.%Si alloy.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Q_t-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Qt-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

HybridAC/DC microgrids(HMG) are emerging as an attracting method for integrating the AC/DC distributed energy resources(DERs) with the features of high-performance and low-cost. In the isolated hybrid AC/DC microgrid (IHMG), the key problem is how to balance the power variation and regulate the voltage and frequency. Various energy storage systems (ESS)and interlinking converter (IC) technologies are viable for this application. The present study proposes a novel unified power flow model to evaluate and compare the abilities of the ESS with different connection topologies and ICs with different control approaches to maintain the voltage and frequency stability of the IHMG. In order to investigate the performance of the proposed scheme, five operation modes of the IHMG are defined and explained. The classification is based on the connection topologies and control modes of the ESS/IC in the IHMG. Then, a set of generic PF equations are derived. Moreover, three binary matrices are applied in the construction of the unified power equations. These matrices are used for describing the running state of the IHMG. Finally, in order to verify the proposed scheme, it is applied to several case studies of the IHMG. The operation characteristics of multi-DC subgrids IHMG in different modes, particularly when an external disturbance occurs, are investigated.

A non-Newtonian fluid model is used to investigate the two-dimensional pulsatile blood flow through a tapered artery with a stenosis. The mixed convection effects of heat and mass transfer are also taken into account. By applying non-dimensionalization and radial coordinate transformation, we simplify the system in a tube. Under the finite difference scheme, numerical solutions are calculated for velocity, temperature concentration, resistance, impedance, wall shear stress and shearing stress at the stenosis throat. Finally, Quantitative analysis is carried out.

Transient flows result in unbalanced forces and high pressure in pipelines. Under these conditions, the combined effects of flow-induced forces along with sudden pipe displacements can create cracks in the pipeline, especially at the junctions. This situation consequently results in water leakage and reduced operational efficiency of the pipeline. In this study, displacements and stresses in a buried pressurized water transmission pipe installed by pipe jacking method are investigated using numerical modeling and considering interactions between fluid, pipe, and soil. The analyses were performed consecutively under no-flow, steady flow, and transient flow conditions, in order to investigate the effects of flow conditions on displacements and stresses in the system. Analyses of the results show that displacements and stresses in the jointed concrete pipes are significant under transient flow conditions. Moreover, because of pressure transient effects, maximum tensile stresses exceed the tensile strength of concrete at the junctions, leading to cracks and consequent water leakage.

Flow and transport processes in soil and rock play a critical role in agricultural non-point source pollution (ANSP) loads. In this study, we investigated the ANPS load discharged into rivers from an irrigation district in the Tibetan Plateau, and simulated ANPS load using a distributed model involving detailed descriptions of flow and ANPS transport and transformation processes in the soil and rock. Experiments were conducted for two years to measure soil water content and nitrogen concentrations and the quality and quantity of lateral flow in the rock and at the drainage canal outlet during the highland barley growing period. A distributed model, in which the subsurface lateral flow was described using a step-wise method, was developed to simulate flow and ammonium nitrogen and nitrate nitrogen transport. Sobol’s method was used to evaluate the sensitivity of simulated flow and transport processes to model inputs. The results showed that, with a 21.2% increase of rainfall and irrigation in the highland barley growing period, the average NH4+-N and NO3--N concentrations in the soil layer decreased by 10.8% and 14.3%, respectively, due to increased deep seepage. Deep seepage of rainfall water accounted for 0–52.4% of total rainfall, whereas deep seepage of irrigation water accounted for 36.6–45.3% of total irrigation. NH4+-N and NO3--N discharged into the drainage channel represented 19.9–30.4% and 19.4–26.7% of the deep seepage, respectively. The mean Nash-Sutcliffe coefficients, root mean square errors, and cumulative deviations between the measured and simulated flow rates and NH4+-N and NO3--N concentrations at the surface drainage canal outlet were 0.694, 0.081, and 0.242, respectively, indicating that the proposed method can effectively describe the hydrological and ANPS pollution migration in the plateau irrigation zone. The Sobol’ sensitivity analysis results demonstrated that subsurface lateral flow had the most important first order and total effect on the simulated flow and NH4+-N and NO3--N concentrations at the surface drainage outlet.

Polluted rivers are a primary problem in Changhua County, Taiwan, due to rapid and massive developments in agriculture and industry. In this study, samples consisted of water influent from the Yangzi-Cuo River, Ci-Tong Jiao, Changhua County. Ecology technology, a combination of gravel contact oxidation and surface flow constructed wetlands, was employed to enhance the water quality. Ecology technology is a useful and ordinary process that focuses on original treatment of pollution through chemical, physical, and biological procedures based on the mediums of soil, plant, water, and microorganisms from pure environments. Moreover, this study aimed to minimize the river pollution index (RPI) of the Yangzi-Cuo River by using combinations of gravel contact oxidation and surface flow constructed wetlands. The inflow volume of the water samples in situ was found to be 1534–2261 cubic meters per day (CMD). The pollution in the water sample mostly involved suspended solid (SS), ammoniacal nitrogen (NH₃–N), total phosphorus (TP), total nitrogen (TN), and biochemical oxygen demand (BOD), and the values of the above indexes were found to be 10.0–26.7 mg/L, 0.9–14.0 mg/L, 1.2–14.1 mg/L, 11.1–18.2 mg/L, and 0.5–3.6 mg/L, respectively. Efficiencies of pollution elimination in SS, NH₃–N, TP, TN, and BOD were found to be 24.2–93.1%, 58.3–86.2%, 5.2–85.0%, 59.4–77.2%, and 46.3–76.4%, correspondingly, after purification treatment via ecology technology. Thus, ecology technology is a valid means of purification treatment for polluted rivers.

Micro channel tube (MCT) is widely employed in industry due to its excellent efficiency in heat transfer. An MCT is commonly produced through extrusion within a porthole die, where severe plastic deformation is inevitably involved. Moreover, the plastic deformation, which dramatically affects the final property of the MCT, varies significantly from location to location. In order to understand the development of the microstructure and its effect on the final property of the MCT, the viscoplastic self-consistent (VPSC) model, together with the finite element analysis and the flow line model, is employed in the current study. The flow line model is used to reproduce the local velocity gradient within the complex porthole die, while VPSC model is employed to predict the evolution of the microstructure accordingly. In addition, electron backscatter diffraction (EBSD) measurement and mechanical tests are used to characterize the evolution of the microstructure and the property of the MCT. The simulation results agree well with the corresponding experimental ones. The influence of the material’s flow line on the evolution of the orientation and morphology of the grains, and the property of the produced MCT are discussed in detail.

The construction industry is one of the most fatal industries, so it is important to pay more attention to safety solutions. Even though work-related accidents are known as major waste in construction projects, little attention has been paid so far to incorporating safety into the lean construction framework. In this research, lean construction theory is reviewed through the lens of safety. That being so, the identified challenges in previous research on improving safety in construction projects are categorized and those related to the concept of lean project delivery are introduced. Then, the principles of the lean construction framework are explained and the relevant changes for incorporating safety into the framework are introduced and discussed. It is expected that this hybrid model would further enrich the lean construction framework. The careful attention of project executives to this model may improve the safety situation in construction projects.

A fluid power industry powering the agricultural machinery faces big challenges nowadays. An issue of energy saving has become important due to increasing fuel costs and more stringent emissions regulations impacting vehicle development. A recent study conducted by the U.S. Department of Energy shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications and create innovative solutions. To increase energy efficiency of fluid power systems reduction of throttling losses and potential energy recovery strategies are needed. Aim of this work is to present classification of current energy saving architectures and aid the development of new techniques for mobile fluid power machines.

In this paper, an attempt has been made to analyze the effect of spool port/ groove geometry on the pressure drop and chamber pressures which effect the performance parameters of the flow distributor valve. The work mainly involves formulation of detailed mathematical model of the valve and compare them on the same platform. For mathematical modelling, Matlab has been used. The size of the orifices is considered same throughout the model for better comparison. Initially the construction and functioning of flow distributor valve along with working principles of hydrostatic motor (Rotary Piston) is shown. Next shown the analytical analysis of area change and pressure drops due to different geometry of the spool valve ports. After that the computational fluid dynamics (CFD) analysis has been shown. A complete mathematical model to describe such flow distributor valve is developed after having a comprehensive knowledge of orifice characteristics, flow interactions based on valve geometry. Equations of flow through different orifices (fixed and variable area) of the valve have been developed based on the relationships obtained earlier.

Today, two very efficient methods for calculation of flow distribution per branches of a looped gas pipeline are available. Most common is improved Hardy Cross method, while the second one is so-called unified node-loop method. For gas pipeline, gas flow rate through a pipe can be determined using Colebrook equation modified by AGA (American Gas Association) for calculation of friction factor accompanied with Darcy-Weisbach equation for pressure drop and second approach is using Renouard equation adopted for gas pipeline calculation. For the development of Renouard equation for gas pipelines some additional thermodynamic properties are involved in comparisons with Colebrook and Darcy-Weisbach model. These differences will be explained. Both equations, the Colebrook’s (accompanied with Darcy-Weisbach scheme) and Renouard’s will be used for calculation of flow through the pipes of one gas pipeline with eight closed loops which are formed by pipes. Consequently four different cases will be examined because the network is calculated using improved Hardy Cross method and unified node-loop method. Some remarks on optimization in this area of engineering also will be mentioned.

Cough peak flow (CPF) is a measurement to evaluate the risk of cough dysfunction and can be measured using various devices, such as spirometers. However, complex device setup and the face mask required to be firmly attached to the mouth impose burdens on both patients and their caregivers. Therefore, this study develops a novel cough strength evaluation method using cough sounds. This paper presents an exponential model to estimate CPF from the cough peak sound pressure level (CPSL). We investigated the relationship between cough sounds and cough flows and the effects of a measurement condition of cough sound, microphone type, and participant’s height and gender on CPF estimation accuracy. The results confirmed that the proposed model estimated CPF with a high accuracy. The absolute error between CPFs and estimated CPFs were significantly lower when the microphone distance from the participant’s mouth was within 30 cm than when the distance exceeded 30 cm. Analysis of the model parameters showed that the estimation accuracy was not affected by participant’s height or gender. These results indicate that the proposed model has the potential to improve the feasibility of measuring and assessing CPF.

To gain insight into the differences between onshore and offshore atmospheric turbulence, 2 pressure fluctuations were measured for offshore wind under different environmental conditions. 3 A durable piezo-electric sensor was used to sample turbulent pressure data at 50 kHz. Offshore 4 measurements were performed at 100 m height on Germany’s FINO3 offshore platform in the 5 German Bight together with additional meteorological data provided by Deutscher Wetterdienst 6 (DWD). The statistical evaluation revealed that the stability state in the atmospheric boundary has a 7 large impact on turbulent fluctuations. Therefore, we used higher statistical properties (described 8 by so-called shape factors) to the stability state. Data was classified to be either within the unstable, 9 neutral or stable stratification. We found that in case of stable stratification, the shape factor is 10 mostly close to zero, indicating that a thermally stable environment produces closer-to Gaussian 11 distributions. Non-Gaussian distributions were found in unstable and neutral boundary layer states 12 and an occurrence probability was estimated. Possible impact on laminar-turbulent transition on the 13 blade is discussed with application of so-called laminar aerofoils on wind turbine blades. Use of a 14 cut-off frequency to separate load and aerodynamic turbulence is proposed.

This paper studied the nonlinear vibrations of top tensioned cantilevered pipes conveying pressurized steady two-phase flow under thermal loading. The coupled axial and transverse governing partial differential equations of motion of the system were derived based on Hamilton’s mechanics with the centreline assumed to be extensible. Multiple scale perturbation method was used to resolve the governing equations, which resulted to an analytical approach for assessing the natural frequency, mode shape and the nonlinear coupled axial and transverse steady state response of the pipe. The analytical assessment reveals that at some frequencies the system is uncoupled, while at some frequencies a 1:2 coupling exists between the axial and the transverse frequencies of the pipe. Nonlinear frequencies versus the amplitude displacement of the cantilever pipe conveying two-phase flow at super critical mixture velocity for the uncoupled scenario exhibit a nonlinear hardening behaviour, an increment in the void fractions of the two-phase flow resulted to a reduction in the pipe’s transverse vibration frequencies and the coupled amplitude of the system. However, increasing the temperature difference, pressure and the presence of top tension were observed to increase the pipe’s transverse vibration frequencies without a significant change in the coupled amplitude of the system.

the intermittency and variability of these permeated Distributed Generators (DGs) could critically cause many security and economy risks to distribution systems. This paper applied a certain mathematical distribution to imitate the output variability and uncertainty of DGs. And then, four risk indices EENS, PLC, EFLC and SI were established to reflect the system risk level of distribution system. For the certain mathematical distribution of the DGs' output power, a developed PEM (point estimate method)-based method was proposed to calculate these four system risk indices. In this developed PEM-based method, enumeration method was used to list the states of distribution systems, an improved PEM was presented to deal with the uncertainties of DGs and the value of load curtailment in distribution systems was calculated by an optimal power flow algorithm. Finally, the effectiveness and advantages of this proposed PEM-based method for distribution system assessment were verified by the tests of a modified IEEE 30-bus system. Simulation results have shown that this proposed PEM-based method has a high computational accuracy and highly reduced computational costs compared with other risk assessment methods and is very effective for risk assessments.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

The precise regulation of hinge moment and pitch angle driven by the pitch regulated mechanism is crucial for modulating thrust requirements and ensuring stable attitude control in Martian coaxial rotorcraft. Nonetheless, the aerodynamic hinge moment in rotorcraft presents time-dependent dynamic properties, posing significant challenges for accurate measurement and assessment for such characteristics. In this study, we delve into the detailed aerodynamic hinge moment characteristics associated with the pitch regulated mechanism of Mars rotorcraft under a spectrum of control strategies. A robust computational fluid dynamics model has been developed to simulate rotor’s aerodynamic loads, accompanied by a quantitative hinge moment characterization that takes into account the effects of varying rotor speeds and pitch angles. Our investigation has yielded a thorough understanding of the interplay between aerodynamic load behavior and rotor surface pressure distributions, leading to the creation of an empirical mapping model for hinge moments. To validate our findings, we engineered a specialized test apparatus capable of measuring the hinge moments of the pitch regulated mechanism, facilitating empirical assessments under replicated atmospheric conditions of both Earth and Mars. The result indicates aerodynamic hinge moments depend non-linearly on rotational speed, peaking at a 0° pitch angle and showing minimal sensitivity to pitch under 0°. Above 0°, hinge moments decrease, reaching a minimum at 15° before rising again. Simulation and experimental comparisons demonstrate that under Earth conditions, the aerodynamic performance and hinge moment errors are within 8.54% and 24.90%, respectively. For Mars conditions, errors remain below 11.62%, proving the CFD model’s reliability. This supports its application in the design and optimization of Mars rotorcraft systems, enhancing their flight control through accurate prediction of aerodynamic hinge moments across various pitch angles and speeds.

Background Few data exist on comparative long-term outcomes of severe aortic stenosis (AS) patients with different flow-gradient patterns undergoing transcatheter aortic valve implantation (TAVI). This study sought to evaluate the impact of pre-TAVI flow-gradient pattern on long-term clinical outcomes after TAVI and assess changes in left ventricular ejection fraction (LVEF) of different subtypes of AS patients following TAVI. Methods Consecutive patients with severe AS undergoing TAVI in our institution were screened and prospectively enrolled. Patients were divided in four subgroups according to pre-TAVI flow/gradient pattern: (i) low flow - low gradient (LF-LG): stroke volume indexed (SVi) ≤ 35ml/m2 and mean gradient (MG) < 40mmHg), (ii) normal flow - low gradient (NF-LG): SVi > 35ml/m2 and MG < 40mmHg, (iii) low flow - high gradient (LF-HG) : SVi ≤ 35ml/m2 and MG ≥ 40mmHg and (iv) normal flow - high gradient (NF-HG): SVi > 35 ml/m2 and MG ≥ 40mmHg. Transthoracic echocardiography was repeated at 1-year follow-up. Clinical follow-up was obtained at 12 months, and yearly thereafter until 5-year follow up was complete for all patients. Results A total of 272 patients with complete echocardiographic and clinical follow-up were included in our analysis. Their mean age was 80±7 years and the majority of patients (N=138, 50.2%) were women. 62 patients (22.8% of the study population) were distributed in LF-LG group, 98 patients (36%) were LF-HG patients, 95 patients (34.9%) were NF-HG, while 17 patients (6.3%) were NF-LG. There was a greater prevalence of comorbidities among LF-LG AS patients. One-year all-cause mortality differed significantly between the four subgroups of AS patients (log rank p: 0.022) and was more prevalent among LF-LG patients (25.8%) compared to LF-HG (11.3%), NF-HG (6.3%) and NF-LG patients (18.8%). At 5-year follow-up, global mortality remained persistently higher among LF-LG patients (64.5%) compared to LF-HG (47.9%), NF-HG (42.9%) and NF-LG patients (58.8%) (log rank p: 0.029). At multivariable Cox hazard regression analysis, baseline SVi (HR: 0.951, 95% C.I.; 0.918 – 0.984), the presence of at least moderate tricuspid regurgitation at baseline (HR: 3.091, 95% C.I: 1.645 - 5.809) and at least moderate paravalvular leak (PVL) post-TAVI (HR: 1.456 , 95% C.I.: 1.106 - 1.792 ) were significant independent predictors of late global mortality. LF-LG patients and LF-HG patients exhibited a significant increase in LVEF at 1-year follow-up. A lower LVEF (p<0.001) and a lower Svi (p<0.001) at baseline were associated with LVEF improvement at 1 year. Conclusions Patients with LF-LG AS have acceptable 1-year outcomes with significant improvement in LVEF at 1-year follow-up, but exhibit an exceedingly high 5-year mortality following TAVI. The presence of low transvalvular flow and at least moderate tricuspid regurgitation at baseline and significant paravalvular leak post-TAVI were associated with poorer long-term outcomes in the entire cohort of AS patients. The presence of a low LVEF or a low SVi predicts LVEF improvement at 1-year.

Physical properties like shape, volume and size affect the dynamics of biological systems. Along these lines, we focus on the topological properties of biological fluids and their biochemical and physiological outcomes. We take as a paradigmatic example the salivary fluid and describe how its topological features may affect the physiopathology of the oral cavity. Topological approaches assess the general properties of saliva, ignoring small-scale physical details such as density, flow rate, stiffness, viscosity. Specifically, the mucin aggregates scattered in the salivary fluid can be tackled in terms of topological holes, i.e., vortical clusters that modify the direction, flow, impulse, local rate-of-change and velocity of saliva. While the current methodological approaches are inclined to remove the effects of impurities assessing systems as homogeneous structures, we argue that the occurrence of mucins breaks up the salivary fluid’s homogeneity, leading to unexpected biophysical modifications. We suggest that every collected salivary sample is not reliable for accurate clinical and experimental investigation, since it displays highly local as well as variable chemical, physical and biological features, not reflecting the current physiological state of the oral cavity. Therefore, the assessment of a single salivary sample is not fully reproducible and cannot provide information about the biophysical, enzymatic and microbiological content of the whole saliva. In sum, the very topological features of the saliva - such as volume, shape, antipodal cells, vortex area, whirling fluid mass, segmentation, discretization, triangulation, node numbering - produce unnoticed biological consequences and network connectivity features with intriguing operational implications.

SARS-CoV-2 infection can lead to life-threatening clinical manifestations. Patients with cardiovascular disease (CVD) are at higher risk for severe courses of COVID-19. However, strategies to predict the course of SARS-CoV-2 infection in CVD patients at the time of hospital admission are still missing. Here, we investigated whether this prediction is achievable by prospectively analysing the blood immunophenotype of 94 participants, including 20 uninfected and 37 acutely SARS-CoV-2-infected CVD patients and 37 healthy donors, using a 36-colour spectral flow cytometry panel. Unsupervised data analysis revealed little differences between healthy donors and CVD patients, whereas the distribution of the cell populations changed dramatically in SARS-CoV-2-infected CVD patients. The latter had more mature NK cells, activated monocyte subsets, central memory CD4+ T cells, and plasmablasts but fewer dendritic cells, CD16+ monocytes, innate lymphoid cells, and CD8+ T cell subsets. Moreover, we identified an immune signature characterised by mucosal-associated invariant T (MAIT) cells, intermediate effector CD8+ T cells, and natural killer T (NKT) cells that is predictive for CVD patients with a severe course of COVID-19. Thus, intensified immunophenotype analyses can help identify patients at risk of severe COVID-19 at hospital admission, improving clinical outcomes through specific treatment.

Using graph theory, computer aided motion, static force and power flow analysis of planetary gear mechanism is realized. The motion, static force and efficiency calculations of 6HP26 automatic transmission are carried out. Based on kinematic and static force analysis model, related matrices are acquired. Hence, kinematic and static force analysis of planetary gear mechanism is achieved. The link power can be determined by the link speed and torque. Power flow diagrams of each gear are acquired. The efficiency is calculated by transmission ratio method.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

Geothermal energy aims at harnessing the heat of the Earth to produce energy, from the near-surface to great depths. Emphasis is put on geothermal reservoirs in crystalline rocks, hence vol-canic islands and crystalline basements of sedimentary basins based on three examples world-wide. Hot brines circulate in those rocks and are responsible for their hydrothermal alteration because of fluid-rock interactions. This includes dissolution of preexisting minerals and crystal-lization of newly formed ones which provide many information of crucial importance for a better exploration of those reservoirs. For example, the crystallization of clay minerals results from the dissolution of preexisting minerals (feldspar and ferro-magnesian minerals in plutonic, volcanic or metamorphic rocks) or from the direct precipitation from geothermal brines, in specific condi-tions. Clay minerals are found in both the geothermal reservoirs and in the clay-cap found above them. Other newly formed minerals such as quartz, carbonates or sulfates have also recorded the conditions of temperature and salinity encountered by fossil reservoirs which can be evaluated thanks to the study of fluid inclusions trapped during their crystallization. This paper presents results from several geothermal deep sites and surface analogues to pinpoint the role played by newly-formed minerals in the characterization of geothermal reservoirs and their cap-rock.

A macro network loading Model for multi-flow lines, time-varying and pedestrian congestion is proposed. The station hub is abstracted as a network of different types of nodes, and the flow of passengers at each node is calculated in real time for the purpose of simulating the hub's collection and distribution process. For correct transmission of passenger flow on heterogeneous networks, three types of indexes are proposed to distinguish the nodes, and then match the corresponding fundamental diagrams. This paper divides the update process of the dynamic network loading model into multiple processes by flow lines, and improves computational speed of DNL model. The proposed model is applied to the simulation of passenger flow collection and distribution in an actual hub station with multi-flow lines. The analysis results illustrate that the model can accurately reflect the realistic congestion facilities and explain the formation process of high-density areas. A rolling passenger flow control model based on optimal control theory is proposed. The effectiveness of the control model is verified based on simulation data.

In swarm-robotics foraging, the purpose of task allocation is to adjust the number of active foraging robots dynamically based on the task demands and changing environment. It is a difficult challenge to generate self-organized foraging behavior in which each robot can adapt to environmental changes. To complete the foraging task efficiently, this paper presents a novel self-organized task allocation strategy known as the dynamic response threshold model (DRTM). To adjust the behavior of the active foraging robots, the proposed DRTM newly introduces the traffic flow density, which can be used to evaluate the robot density. First, the traffic flow density and the amount of obstacle avoidance are used to adjust the threshold which determines the tendency of a robot to respond to a stimulus in the environment. Then, each individual robot uses the threshold and external stimulus to calculate the foraging probability that determines whether or not to go foraging. Simulation and physical experiments are carried out to evaluate the performance of the proposed method. The experimental results show that the DRTM is superior to and more efficient than the adaptive response threshold model (ARTM) in swarm foraging.

Given the significant role of the Ningxia Urban Agglomeration along the Yellow River in reshaping the urban network and promoting coordinated development in the upper Yellow River region of China, this paper takes enterprise flow as the explicit manifestation of the regional urban network. Based on the data of registered enterprises from 2005 to 2021, combined with the interlocking network model, social network analysis method, and spatial panel econometric model, this paper interprets the evolution of the regional urban network structure and its influencing mechanisms through the different types of enterprise flow. The results indicate the following: (1) The external network is primarily focused on outflow investments towards North China, East China, and Northwest China. The overall inflow sources form a multi-origin structure dominated by North China and East China. The Jinfeng and Xingqing serve as core hubs for enterprise exports in the external network and destinations for incoming enterprises. However, in the Productive manufacturing connections, a spatial organizational pattern driven by multiple cities has formed. (2) In the internal network, a concentric connection structure centered around the Jinfeng and Xingqing has formed. The Productive service connections are relatively active, while the Productive manufacturing connections are relatively concentrated between the Jinfeng, Xingqing, Ningdong, and Lingwu. However, there is an imbalance in the spatial connections within the urban agglomeration network and an incomplete hierarchical system of network nodes. (3) In the external network, the main feature is the absorption of external elements to foster development momentum. In the internal network, the Jinfeng and Xingqing serve as contact and radiation sources, influencing various nodes. However, their driving capacity is weak. (4) The market demand and coordinated development both demonstrate significant promoting effects on the connections within the external and internal networks. The sluggish adjustment and transformation of regional industrial structure have resulted in a temporary negative inhibitory effect on the development of transformation. The negative impact of urban investment activities and the positive impact of government management are reflected within the internal network. (5) The improvement of urban management and service functions, as well as external borrowing, can promote the connection in different network. However, the borrowing economic activity can have a negative impact in different networks. (6) Industrial agglomeration can promote enterprises connections in different networks and generate significant spatial spillover effects.

The increasing popularity of unconventional wells has sparked a heightened interest in evaluating and predicting their production performance. With the use of extended reach well structures, these wells are able to generate and access larger reservoir volumes. Hence, it is crucial to understand how the well's lateral trajectory affects its transient production performance. The assessment of lateral trajectory undulating amplitude effect on the flow behavior is performed in the current study based on the experimental results obtained at the University of North Dakota, Undulated Two-Phase (UTP) Flow Loop, injecting air and water mixture through a variable undulating amplitude section followed by a vertical section. The experiments showed that the undulating amplitude increase induced lower translational velocity, frequency, and length, with a consistent slug acceleration through the system profile from the inlet to the vertical section and a decreasing frequency when the slugs travel through the vertical section. Measured data shows that an increase of the horizontal pressure losses and variability is expected with a higher undulation amplitude, translating the fact that larger instabilities are observed for higher amplitudes. The numerical simulation predicted lower translational velocity and frequency, higher slug’s lengths, and similar vertical pressure losses when compared to the experimental results.

Transarterial embolization (TAE) for high-flow pancreaticoduodenal artery (PDA) aneurysms in patients with celiac-trunk stenosis by the median arcuate ligament (MAL) has been found effective both after rupturing and to prevent rupture. The objective was to describe the TAE techniques used and their effectiveness in excluding PDA aneurysms due to MAL syndrome. This single-center retrospective study done at the Dijon-Bourgogne University Hospital included all patients treated by TAE in 2010–2022 for ruptured or unruptured high-flow PDA aneurysms caused by MAL syndrome. We identified 14 patients (7 women and 7 men; mean age, 64 years). Packing and trapping techniques were used alone or together. Occlusion was with microcoils, co-polymer, or cyanoacrylate glue, used separately or combined. Technical success was achieved in 13 (93%) patients. Clinical success was achieved in 12 (86%) patients. One major and two minor complications were recorded within the first 30 days. No complications occurred after 30 days. Follow-up ranged from 1 to 84 months. No cases of aneurysm recanalization were recorded to date. TAE had high technical and clinical success rates in our patients with unruptured or ruptured PDA aneurysms due to MAL syndrome.

Transition delaying is of great importance for the drag and heat flux reduction of hypersonic flight vehicles. The first mode within low frequency and the second mode within high frequency exist simultaneously during the transition of hypersonic boundary layer. This paper proposes a novel bi-frequency synthetic jet to suppress low- and high-frequency disturbances at the same time. Orthogonal table and variance analysis are used to compare the control effects of jet with different frequencies, amplitudes and positions. Linear stability analysis results show that, low frequency synthetic jet can suppress the first mode when it is arranged upstream of synchronization point, while the second mode control effect is relatively weak. The higher the high frequency is, the stronger the suppression effect is on the first mode. For the second mode, the suppression effect is only at f2=89.09kHz. The larger the amplitude, the weaker the promoting effect for the first mode and the second mode, and the more obvious the suppressing effect. For the cases with synthetic jet downstream of synchronization point, all levels of the three parameters promote the unstable mode. In terms of the growth rate with the spanwise wave number, the control effect of the same factor and level under different spanwise wave number is different. In order to obtain the optimal control effect on transition, the three factors and the arrangement position of the synthetic jet should be selected as follows: the position is arranged in the upstream, with f1 = 17.82kHz, f2 = 89.9kHz, a =0.007, so that the maximum growth rate of the first mode is reduced by 9.06% and that of the second mode is reduced by 1.28% compared with the uncontrolled state.

This paper proposes a high-performance and low-cost in-flight collision avoidance system based on background subtraction for unmanned aerial vehicles (UAVs). The pipeline of proposed in-flight collision avoidance system is as follows: (i) dynamic background subtraction to remove the background and to detect moving objects, (ii) denoise using morphology and binarization methods, (iii) Euclidean clustering to cluster the moving object and to remove noise blobs, (iv) distinguish independent objects and track the movement using Kalman filter, and (v) collision avoidance using proposed decision-making techniques. This work focuses on the design and the demonstration of a vision-based fast moving object detection and tracking system with decision-making capabilities to perform evasive maneuvers to replace high vision system such as event camera. The development of high-performance, low-cost unmanned aerial vehicles paired with rapid progress in vision-based perception systems herald a new era of autonomous flight systems with mission-ready capabilities. One of the key features of an autonomous UAV is a robust mid-air collision avoidance strategy. The novelty of our method lies in the motion-compensating moving object detection framework, which accomplishes the task with background subtraction via 2-D transformation approximation. Clustering and tracking algorithms process detection data to track independent objects, and stereo-camera-based distance estimation is conducted to estimate the 3-D trajectory, which is then used during decision-making procedures. The examination of the system is conducted with a quadrotor UAV test vehicle, and appropriate algorithm parameters for various requirements are deduced.

Background. There are scant data about the effectiveness of high flow nasal cannula (HFNC) oxygen therapy in patients hospitalized with severe acute respiratory failure (ARF) in non-intensive medical wards, particularly regarding the effect on arterial oxygenation compared to conventional oxygen therapy (COT) and non-invasive ventilation (NIV) or continuous positive airway pressure (CPAP). Methods. In a retrospective observational study, oxygenation parameters were measured before and immediately after HFNC initiation in 37 consecutive patients hospitalized in a geriatric ward in 2017. Results. HFNC was used as escalation therapy for untreatable hypoxia after failure of NIV/CPAP (n=18) or COT (n=19). Twenty-two patients died, 2 were transferred to the intensive care unit, while 13 were discharged alive. A “do not intubate” status was identified in 17 of the 22 deceased patients. Partial pressure of oxygen (pO2, p< 0.0001), oxygen saturation (SO2, p< 0.0001), pO2/fraction of inspired oxygen ratio (p=0.004) and peripheral SO2 measured by pulse oximetry (p< 0.0001) significantly increased soon after HFNC application. Oxygenation improvements were greater after escalation from NIV/CPAP and in patients discharged alive. Conclusion. HFNC significantly improved oxygenation in severe ARF after failure of COT or NIV/CPAP and may be particularly suitable for older patients hospitalized in non-intensive medical wards.

Smartphone-based point-of-care testing (POCT) is rapidly emerging as an alternative to traditional screening and laboratory testing, particularly in resource-limited settings. In this proof-of-concept study, we present a smartphone- and cloud-based artificial intelligence quantitative analysis system (SCAISY) for relative quantification of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2)-specific IgG antibody lateral flow assays that enables rapid and accurate evaluation of test strips. By capturing an image with a smartphone camera, SCAISY quantitatively analyzes antibody levels and provides results to the user. We analyzed changes in antibody levels over time in over 248 individuals, including vaccine type, number of doses, and infection status, with a standard deviation of less than 10%. We also tracked antibody levels in six participants before and after SARS-CoV-2 infection. Finally, we examined the effects of lighting conditions, camera angle, and smartphone type to ensure consistency and reproducibility. This study suggests that SCAISY is a simple and powerful tool for real-time public health surveillance, enabling the acceleration of quantifying SARS-CoV-2-specific antibodies generated by either vaccination or infection and tracking of personal immunity levels.

Uncultured, unmodified, autologous, adipose-derived regenerative cells (UA-ADRCs) are a safe and effective treatment option for various musculoskeletal pathologies. However, it is unknown whether the composition of the final cell suspension systematically varies with the subject's individual age, sex, body mass index and ethnicity. UA-ADRCs were isolated from lipoaspirate from n=232 subjects undergoing elective lipoplasty using the Transpose RT system (InGeneron, Inc.; Houston, TX, USA). The UA-ADRCs were assessed for the number of nucleated cells, cell viability and the number of viable nucleated cells per gram of adipose tissue harvested. Cells from n=37 subjects were further characterized using four-channel flow cytometry. The present study shows, for the first time, that key characteristics of UA-ADRCs can be independent of the subject's age, sex, BMI and ethnicity. This result has important implications for the general applicability of UA-ADRCs in regeneration of musculoskeletal tissue. Future studies must determine whether in-dependence of key characteristics of UA-ADRCs of the subject's individual age, sex, BMI and eth-nicity only applies to the system used in the present study, or also to others of the more than 25 different experimental methods and commercially available systems used to isolate UA-ADRCs from lipoaspirate that have been described in the literature.

We report the first case of Daratumumab interference of allogeneic crossmatch tests repeatedly causing aberrant false-positive results, which inadvertently delayed transplant for a waitlisted renal patient with multiple myeloma. Daratumumab is an IgG1κ human monoclonal antibody commonly used to treat multiple myeloma, characterized by cancerous plasma cells and often leads to renal failure requiring kidney transplant, by depleting CD38-expressing plasma cells. In this case study, the patient had end-stage renal disease secondary to multiple myeloma and was continuously receiving Daratumumab infusions. The patient did not have any detectable antibodies to human leukocyte antigens but repeatedly had unexpected positive crossmatch by the flow cytometry-based method with 26 of the 27 potential deceased organ donors, implying donor-recipient immunological incompatibility. However, further review and analysis suggested that the positive crossmatches were likely false-positive as a result of interference from Daratumumab binding to donor cell surface CD38 as opposed to the presence of donor-specific antibodies. The observed intensity of the false-positive crossmatches was also highly variable, potentially due to donor- and/or cell-dependent expression of CD38. The variability of CD38 expression was, therefore, for the first time, characterized on the T and B cells isolated from various tissues and peripheral blood of 78 individuals. Overall, T cells were found to have a lower CD38 expression profile than the B cells, and no significant difference was observed between deceased and living individuals. Finally, we show that a simple cell treatment by dithiothreitol can effectively mitigate Daratumumab interference thus preserving the utility of pre-transplant crossmatch in multiple myeloma patients awaiting kidney transplant.

For solving the fractional differential equations in computational fluid dynamics (CFD), it’s complicated and difficult by the Laplace and Fourier transforms. Based on the Caputo fractional derivative, the analytical solutions for unsteady unidirectional flows of a generalized Oldroyd-B fluid are deduced by the separation of variables method. Results show that the analytical solutions are given easily, and have good university. For some specific parameter values, the well-known analytical solutions for the generalized second grade fluid, the generalized Upper-Convected Maxwell (UCM) fluid as well as the ordinary Oldroyd-B fluid can be obtained.

Mandevilla (Apocynaceae) is a greatly appreciated genus in the world ornamental market. In this study, we attempted to address the poor genetic knowledge and the huge taxonomic gaps existing in this genus by analyzing the germplasm of 55 accessions. After cytometrically determining the triploid genome size (1,512.64 Mb) of a reference sample (variety “Mandevilla 2001”), the plastidial genome (cpDNA, 0,18 Mb) and a draft of the nuclear genome (nuDNA, 207 Mb) were assembled. While cpDNA was effective in reconstructing the phylogenesis of the Apocynaceae family based on a DNA superbarcoding approach, the nuDNA assembly length was found to be only 41% of the haploid genome size (506 Mb, predicted based on the K-mer frequency distribution). Its annotation enabled the prediction of thousands of genes, of which 5,275 resulted in full CDS. Among them, we identified nine genes whose orthologs (in Catharanthus roseus) encode enzymes involved in the biosynthesis of monoterpene indole alkaloids (MIAs), including catharanthine, tabersonine and vincadifformine. The nuclear genome draft was also useful to develop a highly informative (mean PIC=0.62) set of 23 SSR markers that was validated on the Mandevilla collection. These results were integrated with cytometric measurements, nuclear ITS1 haplotyping and chloroplast DNA barcoding analyses to assess the origin, divergence and relationships existing among the 55 accessions object of the study. As expected, based on the scarce information available in the literature, the scenario was extremely intricate. A reasonable hypothesis is that most of the accessions represent interspecific hybrids sharing the same species as maternal parent (i.e., Mandevilla sanderi).

A revised reversed Carnot cycle without external heat source and temperature gap is proposed to challenge the classic reversed Carnot cycle, heat pumps based on the proposed cycle with super energy efficiency works just like electric heater fitted for any climate including extreme cold weather, the application of these new heat pumps is discussed with conclusion that little real obstacles exist for scale application to address the heating related climate change, also a demonstration case shows a remarkable results to encourage the applications of these new heat pumps.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

The Pannonian basin major heat system in Central Europe. Their peripheral basins like the East Slovakian basin is a example of a geothermal structure with a linear directed heat flow ranging from 90 to 100 mW /m2 from west to east. However, the use of the geothermal source is limited by several critical tectono-geologic factors: (a) tectonics, and the associated disintegration of the aquifer block by multiple deformations during the pre-Paleogene mainly Miocene period. The main discontinuities of NW-SE and N-S direction negatively affect the permeability of the environment. On the contrary, for utilization are important the secondary minor NE-SW dilatation open fractures which have developed by sinistral transtension on N–S faults and accelerated normal movements to the southeast in the present. (b) hydrogeological conditions, the geothermal structure accommodated three water types, namely Na-HCO3 with 10.9 g.l-1 mineralization (in the north), the Ca-Mg-HCO3 with 0.5 – 4.5 g.l-1 mineralization (in the west), and Na-Cl water type containing 26.8-33.4 g.l-1 (in the southwest) mineralization. The chemical composition is influenced by the Middle Triassic dolomites aquifer as well as by infiltration of saline solutions and meteoric waters along open fractures/faults. (c) geothermally anomalous heat 123 – 129 °C close to volcanic chain with 170 l/s total flow seems to be the perspective for heat production.

Nanoprecipitation by liquid anti-solvent precipitation is one of the most versatile methods to produce pure drug nanoparticles (PDNPs) owing to the ability to optimize the properties of the product. Nevertheless, nanoprecipitation shows broad particle size distribution and low physical stability, leading to high batch-to-batch variability and challenging the bench-to-bedside translation. Microfluidics has emerged as a powerful tool to produce PDNPs in a simple, reproducible, and cost-effective manner with excellent control over NP size. In this work, we designed and fabricated T- and Y-shaped Si-made microfluidics device and used it to produce pure NPs of three kinase inhibitors of different lipophilicity and water-solubility, namely imatinib, dasatinib and tofacitinib, without the use of colloidal stabilizers. PDNPs display sizes in the 90-350 nm range (dynamic light scattering) and a rounded shape (high-resolution scanning electron microscopy). Analysis by X-rays diffraction and differential scanning calorimetry confirmed that this method results in highly amorphous NPs. In addition, we show that the flow rate of solvent, the anti-solvent, and the channel geometry of the device play a key role in the size of the generated NPs.

Artificial intelligence methods may help in unveliling information hidden in high-dimensional oncological data. Flow cytometry studies of haematological malignancies provide quantitative data with the potential to be used for the construction of response biomarkers. Many computational methods from the bioinformatics toolbox can be applied to these data but have not been exploited in their full potential in leukaemias, specifically for the case of childhood B-cell acute lymphoblastic leukemia. In this paper we analysed flow cytometry data obtained on diagnosis from 54 paediatric B-cell acute lymphoblastic leukemia patients from two local institutions. We constructed classifiers based on the Fisher’s Ratio to quantify differences in expression levels of immunophenotypical markers between patients with relapsing and non-relapsing disease. The distribution of the marker CD38 was found and validated to have a strong discriminating power between both patient cohorts, thus providing a classifier.

Predictive simulation of concurrent debris flow using only pre-disaster information has proven to be difficult as a result of problems in predicting the location of debris-flow initiation (i.e., slope failure). However, because catchment topography has concave characteristics, with all channels in a catchment joining each other as they flow downstream, it is possible to predict damage to downstream area using relatively inaccurate initiation points. Based on this, this paper presents methodologies employing debris-flow initiation points generated randomly using statistical slope failure prediction. A many-case simulation across numerous initiation points was performed to quantify the effect of slope-failure location in terms of deviations in the predicted water level and terrain deformation. It was found that the relative standard deviation diminished as the points approached the downstream area, indicating a location-based predictability effect.

Based on the topology of wide area protection system (WAPS), after studying the reliability of hardware system and information flow in the WAPS and establishing the reliability assessment model, the multi-service reliability analysis method with multi monitoring and protection tasks in WAPS was proposed. In the model, the impact of network quality of service (QoS) such as information flow loss and delay, is studied. On the base of the model, the multi-service reliability evaluation method is employed to analyze the reliability of a WAPS of IEEE14 node power system, and the key nodes of the WAPS is given, which provides a basis for improving the reliability of the WAPS.