The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Following the rapid spread of COVID-19 across the globe, the intense response that was demanded of diagnostic centers and research laboratories prompted the use of numerous products and protocols for the management of SARS-CoV-2 specimens. In these settings, proper handling of such infectious specimen is necessary to ensure the safety of personnel and to reduce the risk of active transmission. Our aim was to evaluate the inactivation efficacy of different inactivating methods, notably from commercial lysis buffers available in diagnostic kits. Heat and sodium dodecyl sulfate detergent were also included in our investigations. A cell culture-based assay was used, and supported by molecular qRT-PCR detection, to show in vitro infectivity reduction after inactivation treatment. Overall, all the investigated methods were successful in inactivating SARS-CoV-2. Ten minutes of contact with the commercial buffers completely stopped in vitro SARS-CoV-2 infectivity. Fifteen minutes at 68°C and 30 minutes at 56°C as well as one hour with sodium dodecyl sulfate detergent at 2, 1, 0.5, and 0.1% yielded the same results. These findings demonstrate the reliability of these protocols with regards to biosafety. Inactivation by heat and sodium dodecyl sulfate detergent are rather simple and can be readily available methods for rendering an infectious SARS-CoV-2 specimen inactive, especially in settings where commercial buffers are not available.

Thermal simulations are an important part in the design of electronic systems, especially as systems with high power density become common. In simulation-based design approaches, a considerable amount of time is spent by repeated simulations. In this work, we present a proof-of-concept study of the application of convolutional neural networks to accelerate those thermal simulations. The goal is not to replace standard simulation tools but to provide a method to quickly select promising samples for more detailed investigations. Based on a training set of randomly generated circuits with corresponding Finite Element solutions, the full 3D steady-state temperature field is estimated using a fully convolutional neural network. A custom network architecture is proposed which captures the long-range correlations present in heat conduction problems. We test the network on a separate dataset and find that the mean relative error is around 2 % and the typical evaluation time is 35 ms per sample ( 2 ms for evaluation, 33 ms for data transfer). The benefit of this neural-network-based approach is that, once training is completed, the network can be applied to any system within the design space spanned by the randomised training dataset (which includes different components, material properties, different positioning of components on a PCB, etc.).

We aimed to evaluate the protective effects of acetyl-xylogalactan on the activity of RAW264.7 macrophages against heat stress. To this end, we assessed cell survival, phagocytic activity, in-tracellular Ca2+ level, mitochondria potential exchange, apoptotic assay findings, galactosidase activity and the RNA-seq by NGS and real-time polymerase chain reaction (PCR) expression. In our evaluation of macrophage morphology at 37°C and 41°C, the macrophages showed an oval shape at 41°C , unlike the spindle shape at 37°C. Therefore, 41°C was chosen as the heat stress condition. Subsequently, we designed an experiment to evaluate changes in the RAW264.7 macrophages after acetyl-xylogalactan treatment under heat stress. The survival of RAW264.7 macrophages treated with acetyl-xylogalactan was higher than that of controls that were not treated with acetyl-xylogalactan. Moreover, on the basis of the results of the annexin-V detection assay, the apoptotic activity of macrophages appeared to have reduced after treatment with ac-etyl-xylogalactan. Moreover, treatment with acetyl-xylogalactan resulted in a stronger recovery trend in the intracellular Ca2+ and mitochondrial membrane potential after heat stress. RNA sequencing and real-time polymerase chain reaction (PCR) illustrated that Sarcodia suieae acetyl-xylogalactan could upregulate the expression of the anti-apoptosis Cflar gene and down-regulate the expression of the apoptosis factors Ddit3, and Hyou1 to protect macrophages under heat stress.

Objective On the eve of the summer Olympic Games in Tokyo research focus has shifted on the core temperature responses of elite athletes competing in the heat. In the absence of the field data of core temperature during Olympic sailing competition aim of the present study was to identify core temperature response during the Tokyo 2020 Olympic Test Event. Methods Four elite athletes from Olympic sailing (177.5±5.2 cm, 71.1±7.4 kg, body mass index 22.5±1.4 kg/m2, 24.8±3.7 yrs, VO2max 50.6±7.2 mL/min/kg)): 2 males and 2 females participated in the study. Core temperature was recorded using e-Celsius ingestible capsules, heart rate using a heart rate monitor. Ambient conditions in direct sunlight were measured using portable meteo station. Results Core temperature was recorded at water environment via an ingestible capsule in 4 sailors during the training (T), and competition (C), respectively. Ambient conditions in direct sunlight were hot and humid: during training temperature were 30.9°C±1.7°C and relative humidity 81.4%±2.8%, corresponding to a wet-bulb globe temperature of 41°C±4°C and during competition temperature was 31.2°C±2.3°C and relative humidity 87.2%±4.4%, corresponding to a wet-bulb globe temperature of 45.2°C±8.9°C. Core temperature increased during training reaching higher peak values (38.6°C±0.4°C) and during competition (38.9°C±0.4°C). The highest temperature recorded was 39.4°C (C). Conclusion The current study provides unique information into the core temperature parameters under heat stress in elite Olympic sailors during training and race event.

The objective of this study was to evaluate biomarkers of heat stress (HS) from automatic milking system (AMS), the relationships between measurements of temperature-humidity index (THI) and reticulorumen ph and temperature and some automatic milking systems parameters in dairy cows (rumination time (RT), milk traits, body weight (BW) and consumption of concentrate (CC)) during summer period. The experiment was carried out on a dairy farm at 54.9587408, 23.784146. Lithuanian Black and White dairy cows (n=365) were selected. The cows were milked with Lely Astronaut® A3 milking robots with free traffic. The rations were calculated to meet physiological requirements of the animals. Daily milk yield, rumination time, body weight, milk fat and protein ratio were collected from the Lely T4C management program for analysis. The pH and temperature of the contents of cow reticulorumen were measured using specific smaX-tec boluses manufactured for animal care. The daily humidity and air temperature in the farm zone were obtained from the adjacent weather station (2 km away). According this study during HS, the higher THI had positive correlation with ML, which show tendencies to increase risk of mastitis, and decrease CC, RT, BW, MY, reticulorumen ph and F/P. Some biomarkers of HS can be milk yield, milk lactose, somatic cell count, concentrate conception, rumination time, body weight, reticulorumen ph and milk fat – protein ratio. We can recommend to monitoring these parameters in the herd management program to identify possibility of heat stress.

Alzheimer’s disease is a prominent neurological disorder, which leads to progressive dementia. The microtubule-associated protein Tau is been considered as one of the major causes of Alzheimer’s disease. Physiologically Tau assists in the stabilization of microtubules, contrary to this the pathological state of Tau results in the formation of neurotoxic tangles of Tau. The posttranslational modifications, such as GSK-3β-mediated Tau phosphorylation results in the generation of Tau pathology. Neuroinflammation generated in Alzheimer’s disease, contributes to elevated body temperature. The aim of present work is to study the effect of high temperature on Tau phosphorylation. The neuroblastoma cells were exposed to heat stress for 40 minutes. The immunofluorescence and western blot studies suggested that high temperature increases the levels of GSK-3β in cells. Heat stressed cells was also observed to have elevated levels of phosphorylated Tau. Additionally, heat stressed cells found to have modulated nuclear transport as the level of Ran was reduced. The results of present work suggested that increased temperature could be considered as a risk factor in Alzheimer’s disease as it elevated the GSK-3β levels in cells thus, resulting in increased Tau phosphorylation.

Energy system optimization models (ESOM) are widely used to inform about energy transition strategies. The heterogeneity of consumers, especially in the heat sector, is rarely considered in these model types. Integrating consumer heterogeneity and behavioral factors into ESOMs may generate new insights for energy policy. In this study a literature review was conducted, identifying empirical data on consumer behavior for adopting residential heating systems. This data was integrated into an ESOM for the German heat sector, combining established methods for integrating consumer heterogeneity and a novel approach for calculating indirect costs, representing behavioral factors. The incorporation of consumer choice leads to a higher diversity in technology market shares in a business as usual and an ambitious measures scenario. Especially, the future role of log wood technologies in the private household sector may have been underestimated in previous studies and should be discussed, when designing policies. Still, these findings need to be handled with care, since the empirical data basis and the methodological basis is limited.

Chronic heat stress (HS), aggravated by global warming, reduces the production efficiency of the buffalo dairy industry. Here, we conducted a proteomic analysis to investigate the adaptation strategies used by buffalo in response to heat stress. Seventeen differentially abundant proteins with known functions were detected using label-free quantification (LFQ), and five of these differentially expressed proteins were validated with parallel reaction monitoring (PRM). These five proteins were associated with various aspects of heat stress, including decreased heat production, increased blood oxygen delivery, and enhanced natural disease resistance. Lipase (LPL), glutathione peroxidase 3 (GPX3), cathelicidin-2 (CATHL2, LL-37), ceruloplasmin (CP), and hemoglobin subunit alpha 1 (HBA1) were shown to play cooperative roles in the tolerance of chronic HS in dairy buffalo. We found that high levels of HBA1 increased blood oxygen transport capacity. Our results increase our understanding of the adaptation of dairy buffalo to chronic heat stress.

We apply the stochastic thermodynamics formalism to describe the dynamics of systems of complex Langevin and Fokker-Planck equations. We provide in particular a simple and general recipe to calculate thermodynamical currents, dissipated and propagating heat for networks of nonlinear oscillators. By using the Hodge decomposition of thermodynamical forces and fluxes, we derive a formula for entropy production that generalises the notion of non-potential forces and makes transparent the breaking of detailed balance and of time reversal symmetry for states arbitrarily far from equilibrium. Our formalism is then applied to describe the off-equilibrium thermodynamics of a few examples, notably a continuum ferromagnet, a network of classical spin-oscillators and the Frenkel-Kontorova model of nano friction.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

This study examines the optimization of ground source heat pump (GSHP) systems and energy piles for sustainable urban development, with a focus on Southeast Asia. GSHPs, which utilize geothermal energy for indoor HVAC needs, offer a sustainable alternative to traditional systems by utilizing consistent subsurface temperatures for heating and cooling. The study highlights the importance of understanding thermal movement within the soil, especially in soft marine clays prevalent in Southeast Asia, to improve GSHP system efficiency. Using a one-dimensional finite-difference model, the study examines the effects of soil thermal conductivity and density on system performance. The results show that GSHP systems, especially when integrated with energy piles, significantly reduce electricity consumption and greenhouse gas emissions, underscoring their potential to mitigate the urban heat island effect in densely populated areas. Despite challenges posed by the region's hot and humid climate, which could affect long-term effectiveness, the study highlights the need for further study, including field experiments and advanced modeling techniques, to optimize GSHP configurations and fully exploit geothermal energy in urban environments. The study's insights into soil thermal dynamics and system design optimization contribute to the advancement of sustainable urban infrastructure development.

Remote sensing technologies are critical for analyzing the escalating impacts of global climate change and increasing urbanization, providing vital insights into land surface temperature (LST), land use and cover (LULC) changes, and the identification of urban heat island (UHI) and surface urban heat island (SUHI) phenomena. This research focuses on the nexus between LULC alterations and variations in LST and air temperature (Tair), with a specific emphasis on the intensified SUHI effect in Kharkiv, Ukraine. Employing an integrated approach, the study analyzes time-series data from Landsat and MODIS satellites, alongside Tair climate records, utilizing machine learning techniques and linear regression analysis. Key findings indicate a statistically significant upward trend in Tair and LST during summer months from 1984 to 2023, with a notable positive correlation between Tair and LST across both datasets. MODIS data exhibit a stronger correlation R² = 0.879, compared to Landsat R² = 0.663. The application of supervised classification through Random Forest algorithms and vegetation indices on LULC data reveals significant alterations, manifested as a 70.3% increase in urban land, concurrently with a decrement in vegetative cover, especially 15.5% reduction in dense vegetation and a 62.9% decrease in sparse vegetation. Change detection analysis elucidates a 24.6% conversion of sparse vegetation into urban land, underscoring a pronounced trajectory towards urbanization. Temporal and seasonal LST variations across different LULC classes were analyzed using kernel density estimation (KDE) and boxplot analysis. Urban areas and sparse vegetation had the smallest average LST fluctuations, at 2.09°C and 2.16°C, respectively, but recorded the most extreme LST values. Water and dense vegetation classes exhibited slightly larger fluctuations of 2.30°C and 2.24°C, with the bare land class showing the highest fluctuation 2.46°C, but fewer extremes. Quantitative analysis with the application of Kolmogorov-Smirnov tests across various LULC classes substantiated the normality of LST distributions p > 0.05 for both monthly and annual data sets. Conversely, the Shapiro-Wilk test validated the normal distribution hypothesis exclusively for monthly data, indicating deviations from normality in the annual data. Thresholded LST classifies urban and bare lands as warmest classes with 39.51°C, 38.20°C and water by 35.96°C and dense vegetation 35.52°C, sparse vegetation 37.71°C as coldest, a trend consistent annually and monthly. The analysis of SUHI effects demonstrates an increasing trend in UHI intensity, with statistical trends indicating a growth in average SUHI values over time. This comprehensive study underscores the critical role of remote sensing in understanding and addressing the impacts of climate change and urbanization on local and global climates, emphasizing the need for sustainable urban planning and green infrastructure to mitigate UHI effects.

Despite the remarkable success of Carnot’s heat engine cycle in founding the discipline of thermodynamics two centuries ago, false viewpoints of his use of the caloric theory in the cycle still linger, limiting his legacy. An action revision of the Carnot cycle can correct this, showing that the heat flow powering external mechanical work is compensated internally with configurational changes in the thermodynamic or Gibbs potential of the working fluid, differing in each stage of the cycle quantified by Carnot as caloric. Action (@) is a property of state having the same physical dimensions as angular momentum (mrv=mr2ω). However, this property is scalar rather than vectorial, including a dimensionless phase angle (@=mr2ωδφ). We have recently confirmed with atmospheric gases that their entropy is a logarithmic function of the relative vibrational, rotational and translational action ratios with Planck’s quantum of action ħ. The Carnot principle shows that the maximum rate of work (puissance motrice) possible from the reversible cycle is controlled by the difference in temperature of the hot source and the cold sink, the colder the better. This temperature difference between the source and the sink also controls the isothermal variations of the Gibbs potential of the working fluid, that Carnot identified as reversible temperature-dependent but unequal exchanges in caloric. Importantly, the engine’s inertia ensures that heat from work performed adiabatically in the expansion phase is all restored to the working fluid during the adiabatic recompression, less the net work performed. This allows both the energy and the thermodynamic potential to return to the same values at the beginning of each cycle, a point strongly emphasized by Carnot. Our action revision equates Carnot’s calorique, or the non-sensible heat later described by Clausius as ‘work-heat’ exclusively to negative Gibbs energy (-G) or quantum field energy. This action field complements the sensible energy or vis-viva heat as molecular kinetic motion and its recognition should have significance for designing more efficient heat engines or better understanding of the heat engine powering the Earth’s climates.

The inhibition of heat shock protein 90 (Hsp90) a molecular chaperone for multiple oncogenic client proteins is considered as a promising approach to overcome radioresistance. Since most Hsp90 inhibitors activate HSF-1 that induces the transcription of cytoprotective and tumor-promoting stress proteins such as Hsp70 and Hsp27, a combined approach consisting of HSF-1 knockdown (k.d.) and Hsp90 inhibition was investigated. A specific HSF-1 k.d. was achieved in H1339 lung cancer cells using RNAi-Ready pSIRENRetroQ vectors with puromycin resistance. The Hsp90 inhibitor NVP-AUY922 was evaluated at low concentrations - ranging from 1-10nM - in control and HSF-1 k.d. cells. Protein expression (i.e., Hsp27/Hsp70, HSF-1, pHSF-1) and transcriptional activity was assessed by Western blot analysis and luciferase assays and radiosensitivity was measured by proliferation, apoptosis (Annexin V, active caspase 3), clonogenic cell survival, alkaline comet, γH2AX, 53BP1 and Rad51 foci assays. The k.d. of HSF-1 resulted in a significant reduction of basal and NVP-AUY922-induced Hsp70/Hsp27 expression levels. A combined approach consisting of HSF-1 k.d. and low concentrations of the Hsp90 inhibitor NVP-AUY922 potentiates radiosensitization which involves an impaired homologous recombination mediated by Rad51. Our findings are key for clinical applications of Hsp90 inhibitors with respect to adverse hepatotoxic effects.

Temperature differences between the atmosphere and river water allow rivers to be used as a hydrothermal energy source. The river-water heat pump system is a relatively non-invasive renewable energy source; however, effluent discharged from the heat pump can cause downstream temperature changes which may impact sensitive fluvial ecosystems. In this study, the water temperature recovery distance of the effluent was estimated for a river section in the Han River Basin, Korea, using the heat transfer equation and the Environmental Fluid Dynamic Code (EFDC) model. Results showed that, compared to the EFDC model, the heat transfer equation tended to overestimate the water temperature recovery distance due to its simplified assumptions. The water temperature recovery distance could also be used as an objective indicator to decide the reuse of downstream river water. Furthermore, as the river system was found to support an endangered fish species that is sensitive to water environment changes, care should be taken to exclude the habitats of protected species affected by water temperatures within water temperature recovery distance.

Heart failure (HF) is a life-threatening disorder and is treated by drug therapies and surgical interventions such as heart transplantation and left ventricular assist device (LVAD). However, these treatments can lack effectiveness in the long term and are associated with issues such as donor shortage in heart transplantation, and infection, stroke, or gastrointestinal bleeding in LVADs. Therefore, alternative therapeutic strategies are still needed. In this respect, stem cell therapy has been introduced for the treatment of HF and numerous preclinical and clinical studies using various types of stem cells, such as embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs) have been shown to improve cardiac function and attenuate left ventricular remodeling. IPSCs, which have a capacity of unlimited proliferation and differentiation to cardiomyocytes, are a promising cell source for myocardial regeneration therapy. This review discusses the current status of cardiac regenerative therapy using iPSCs.

Pluripotent stem cells (PSCs) can differentiate into three germ layers and diverse autolo-gous cell lines. Being among the most commonly used large domesticated hoofed animals and serving as a vital source of food and bioreactors, cattle are among the many species in which PSCs have been developed. Bovine PSCs (bPSCs) are the "seed cells" of regenerative science and have immense potential to advance species propagation, genetic engineering, and disease treatment. Moreover, they can aid in screening new drugs for efficacy and toxicity, model human diseases, and establish a sustainable agricultural system that can cater to the needs of the growing global population. Establishing stable bPSCs in vitro has been a critical scientific challenge, and researchers have made numerous attempts to address this issue. This review primarily delves into the current research progress of bPSCs, the challenges faced, and their potential applications.

During geomagnetic storms, which are a result of solar wind interaction with the Earth’s magnetosphere, geomagnetically induced currents (GICs) begin to flow in the long-distance high-voltage power grids on the Earth’s surface. It causes a number of negative phenomena that affect the normal operation of the entire electric power system. To investigate the nature of the phenomenon and its possible effects on transformers, a GIC monitoring system was created in 2011, the devices of which were installed at five substations of the Kola-Karelian power transit in northwestern Russia. Over 12 years of operating the system a large amount of data has been accumulated, which cannot be analyzed manually within a reasonable amount of time. To analyze the constantly growing volume of recorded data effectively, a method for automatic classification of GIC in autotransformer neutral was proposed. The method is based on a continuous wavelet transform of the neutral current data combined with a convolutional neural network (CNN) to classify the obtained scalogram images. As the result of comparing four CNNs with different architectures, a model that showed excellent GIC classification performance on the validation set (100.00% accuracy and loss of 0.0115) was chosen.

Inflammatory bowel disease (IBD), including ulcerative colitis and Crohn's disease, is a complex gastrointestinal disorder with a multifactorial etiology, including environmental triggers, autoimmune mechanisms, and genetic predisposition. Despite advancements in therapeutic strategies for IBD, its associated mortality rate continues to rise, which is often attributed to unforeseen side effects of conventional treatments. In this context, we explored the potential of Ecklonia cava extract (ECE) derived from an edible marine alga known for its anti-inflammatory and antioxidant properties in mitigating IBD. This study investigated the effectiveness of ECE as a preventive agent in a murine model of dextran sulfate sodium (DSS)-induced colitis. Our findings revealed that pretreatment with ECE significantly ameliorated colitis severity as evidenced by increased colon length, reduced spleen weight, and histological improvements demonstrated by immunohistochemical analysis. Furthermore, ECE significantly attenuated the upregulation of inflammatory cytokines and mediators and the infiltration of immune cells known to be prominent features of colitis in mice. Notably, ECE restored dysbiosis of intestinal microflora and aided in the recovery of damaged intestinal mucosa. Mechanistically, ECE exhibited protective effects against pathogenic colitis by inhibiting the NLRP3/NF-κB pathway known to be pivotal regulators in the inflammatory signaling cascade. These compelling results suggest that ECE holds promise as a potential candidate for IBD prevention. It might be developed into a functional food for promoting gastrointestinal health. This research sheds light on the preventive potential of natural compounds like ECE in the management of IBD, offering a safer and more effective approach to combating this challenging disease.

Vibrations of plate structures placed in a supersonic flow is considered. The undisturbed fluid flow is parallel to the plate. Two specific problems are treated: in the first one the plate is in the form of an infinite strip and the flow is in the direction of its finite length. Rigid walls extend from the sides of the plate indefinitely. In the second problem, the plate is a finite rectangle and the flow is parallel to one of its sides. The first problem is a limiting case of the second problem. The flow is modeled by piston theory which assumes that the fluid pressure on the plate is proportional to local slope. This approximation is widely used at high speeds, and reduces the interaction between the fluid flow and the vibrations of the plate to an additional term in the vibration equation. The resulting problem can be solved by assumed mode methods. In this study, the solution is also carried out by using the collocation method. The main result is the flutter velocity of the free fluid flow under which the plate vibrations become unstable. Finally, simple expressions are proposed between the various non-dimensional parameters that allows quick estimation of flutter velocity.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (>4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

The fall armyworm (FAW), Spodoptera frugiperda, has become one of the most important pests on corn in China since it invaded in 2019. Although FAW has not been reported to cause widespread damage to rice plants in China, it has been sporadically found feeding in the field. If FAW infests rice in China, the fitness of other insect pests on rice may be influenced. However, how FAW and other insect pests on rice interact remains unknown. In this study, we found that the infestation of FAW larvae on rice plants prolonged the developmental duration of the brown planthopper (BPH, Nilaparvata lugens (Stål)) eggs, and plants damaged by gravid BPH females did not induce defenses that influenced the growth of FAW larvae. Moreover, co-infestation by FAW larvae on rice plants did not influence the attractiveness of volatiles emitted from BPH-infested plants to Anagrus nilaparvatae, an egg parasitoid of rice planthoppers. FAW larvae were able to prey on BPH eggs laid on rice plants and grew faster compared to those larvae that lacked available eggs. Studies revealed that the delay in development of BPH eggs on FAW-infested plants was probably related to the increase in levels of jasmonoyl-isoleucine, abscisic acid and the defensive compounds in the rice leaf sheaths on which BPH eggs were laid. These findings indicate that if FAW invades rice plants in China, the population density of BPH may be decreased by intraguild predation and induced plant defenses, whereas the population density of FAW may be increased.

The current study aimed to investigate the antitumor effects and potent mechanism of cytokine-induced killer (CIK) cells combined with irreversible electroporation (IRE) via an in vitro function assay in an in vivo Panc02 cell–bearing mouse model. We established an in vitro culture assay for CIK cells and determined the proportions of different peripheral lymphocytes. The antitumor effect of the combination of IRE and CIK cells in a Panc02 pancreatic-cancer (PC) subcutaneous-xenograft model was investigated; tumor size and mouse survival rates were recorded. We used flow cytometry (FCM) to analyze the proportion of intratumoral lymphocytes, the expression of chemokine receptors, and the proliferative activity of CIK cells. The proportion of cells that were positive for clusters of differentiation 3 and 8 (CD3+CD8+) and the proportion of CD3+CD56+ cells were both significantly increased after 21 days of in vitro culture. Combined IRE/CIK cell treatment significantly inhibited tumor growth and increased the survival rate of Panc02 cell–bearing mice. Furthermore, infiltration of lymphocytes into tumor tissue was significantly increased by this combination therapy compared with the untreated group or monotherapy group. In addition, IRE significantly enhanced the expression of chemokine receptors elicited by, and the proliferative activity of, CIK cells. In conclusion, IRE combined with CIK cells showed superior antitumor efficacy in a PC subcutaneous-xenograft model, which we attributed to the promotion of lymphocytic infiltration, as well as to upregulation of chemokine receptor expression and of regulators of CIK cell proliferation.

Background: Despite the existence of a wide variety of anti-inflammatory drugs, the vast majority are classified as steroidal or non-steroidal. Both classes with many side effects that limit usage. Thus, the search for new molecules with anti-inflammatory potential is still important. Methods: Five phenylbenzohydrazides were synthetized and evaluated in pre-clinical models of acute inflammation in vivo and in vitro. Results: Substances significantly reduced cell migration induced by carrageenan. It was also observed an intense inhibition in protein extravasation and cytokines (IL-6, IL-1β, and TNF-α) production as well as nitric oxide reduction. INL-11 demonstrated to be the most potent since the reduction was significant even when compared with dexamethasone. In vitro INLs also reduced cytokines and NO production and iNOS activity. INL-11 was the most effective in reducing cell migration in vitro. Conclusions: our data suggest that these substances are suitable for further development to new series of compounds that could lead to new hits and future drug prototypes for anti-inflammatory conditions.

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

Arboviruses of medical and veterinary significance have been identified on all 7 continents with every human and animal population at risk for exposure. Like arboviruses, chronic neurodegenerative diseases like Alzheimer’s and Parkinson’s disease are found wherever there are humans. Viral parkinsonism has been documented for a variety of human pathogens though there are few studies that evaluate the effects of viral infection on degenerative neurological diseases. Significant differences in baseline gene and protein expression have been determined between Human Induced Pluripotent Stem Cell lines derived from a non-Parkinson’s disease individual and from an individual with reported Parkinson’s disease. While the organoids generated from each cell line were physically indistinguishable, significant differences were observed in gene and protein expression for neurotransmission and immunity. It was hypothesized that these inherent differences would impact cerebral organoid responses to viral infection. In this preliminary observational study, cerebral organoids from a non-Parkinson’s and Parkinson’s patient were infected with Chikungunya virus and observed for 2 weeks. Parkinson’s organoids lost mass and exhibited a dysfunctional antiviral response. Neurotransmission data from both non-Parkinson’s and Parkinson’s organoids had dysregulation of IL-1, IL-10, IL-6. These cytokines are associated with mood and could be contributing to persistent depression seen in patients following CHIKV infection. Both organoid types had increased expression of CCR5 and CXCL10 which are linked to demyelination, highlighting a potential mechanism for virus-associated parkinsonism. The dysfunctional antiviral response of Parkinson’s organoids highlights the need for more research in neurotropic infections in a neurologically compromised host.

The development of 3D cerebral brain organoids which accurately resemble aspects of the human brain permits a more accurate characterization of physiological processes and neurological diseases. Cerebral organoids can be grown from stem cell lines with various genetic backgrounds allowing multiple neurodegenerative diseases to be modeled. While dysfunction in neurotransmission of patients with neurodegenerative diseases is expected, the impact of chronic neurodegeneration on the response to viral infection of the CNS is poorly understood. For instance, several mosquito-borne viruses like Dengue virus and West Nile Virus cause post-viral parkinsonism. How CNS infection might impact a host with inherent CNS dysfunction such as Parkinson’s Disease in poorly understood. This preliminary, observational study aimed to understand dysfunction in intrinsic and innate expression of a patient with a neurodegenerative disease and a non-affected individual in relation to potential viral infection in the CNS. Cerebral organoids were generated from human induced pluripotent stem cells with a normal genetic background or with idiopathic Parkinson’s Disease. After differentiation and maturation, organoid size, gene expression and immunofluorescence were evaluated to assess neurotransmission and innate immunity. While there was no significant difference in size of the organoids with a normal or Parkinson’s genetic background, gene expression studies identified multiple differences in innate immunity and neurotransmission. Immunofluorescence also identified differences in protein expression related to neurotransmission and innate immunity. Of note, organoids derived from a Parkinson’s patient exhibited endogenous up-regulation of dopamine and muscarinic acetylcholine receptors, GABA, glycine, and glutamate targets, and the majority of cytokines. This expression pattern suggests a chronic state of neuroexcitation and neuroinflammation in this population of organoids.

Introduction: Valproic acid (VPA) is an antiepileptic drug extensively used for treating partial and generalised seizures, acute mania and as prophylaxis for bipolar disorder. Drug-induced liver injury (DILI) persists as a significant issue related to fatal outcomes by VPA. The aim of this study was to increase our knowledge about this condition and to better identify patients affected. Methods: We conducted an observational retrospective case-control study that identified cases of DILI by VPA from the Pharmacovigilance Programme from our Laboratory Signals at La Paz University Hospital from January 2007 to December 2019. From the Therapeutic VPA Monitoring Programme, two control groups were assigned, VPA-tolerant patients and the other with patients who developed mild VPA-related hepatitis but who did not meet the DILI criteria, matched for date, age and sex. Results: A total of 60 patients were included in the study: 15 cases of DILI, 30 VPA-tolerant controls and 15 controls with mild hepatitis. Mean age for the cases was 45.7 years, 4(26.7%) were women and 5(33.34%) were children under 18 years, of them 3(20%) were fatal. Polytherapy with other antiepileptic drugs (p=0.047) and alcohol consumption (p<0.001) were associated with a greater risk of developing DILI by VPA. A diagnosis of epileptic seizure was more frequently related to DILI when compared with the VPA-tolerant controls (p<0.001). The cases developed hepatocellular hepatitis (p<0.001), while the mild hepatitis controls had a higher rate of cholestatic hepatitis (p<0.001). The laboratory lactate dehydrogenase values were statistically higher (even at baseline) in patients with DILI than in both control groups (p= 0.033 and p=0.039). Conclusions: VPA hepatotoxicity remains a considerable problem. This study offers interesting findings for characterising VPA-induced liver injury and at-risk patients.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

We report on space-selective crystallization of congruent and polar Sr2TiSi2O8 crystals in a stoichiometric SrO-TiO2-SiO2 glass induced by (1030 nm, 300 fs) femtosecond laser irradiation. This allows us to compare with non-congruent laser induced crystallization of polar LiNbO3, in non stoichiometric Li2O-Nb2O5-SiO2 glass and gain information on the mechanism of nanocrystals orientation with the laser polarization that we pointed out previously. Using scanning electron microscopy (SEM), Second-harmonic generation (SHG) and electron backscattered diffraction (EBSD), we studied the laser induced crystallization according to the laser processing parameters (pulse energy, pulse repetition rate, scanning speed). We found 1) a domain where the laser track is filled with crystals not perfectly textured (low energy), 2) a domain where an amorphous volume remain surrounded by a crystallized shell (high energy). This arises from Sr out-diffusion and may gives rise to crystallization of both SrTiO3 and Sr2TiSi2O8 phases at low speed. In the one-phase domain (at higher speed), it is found the possibility to elaborate a tube with a perfect fresnoite texture. Significant difference in size and morphology whereas crystallization threshold remains similar are discussed based on glases thermal propeties. Contrarily to Li2O-Nb2O5-SiO2 (LNS) glass, no domain of oriented nanocrystallization controlled by the laser polarization has been found in SrO-TiO2-SiO2 (STS) glass, which is attributed to the larger crystallization speed in STS glass. No nanogratings have also been found that is likely due to the congruency of the glass.

Inertial focusing conditions of fluorescent polystyrene spherical particles are studied at the pointwise level along their pathlines. This is accomplished by an algorithm that calculates a de-gree of spreading function of the particles' trajectories taking streaklines images as raw data. Different confinement ratios of the particles and flow rates are studied and the results are pre-sented in state diagrams showing the focusing degree of the particles in terms of their position within a curve of an asymmetric serpentine and the applied flow rate. In addition, together with numerical simulation results, we present empirical evidence that the preferred trajectories of inertially focused spheres are contained within Dean vortices' centerlines. We speculate about the existence of a new force, never postulated before, to explain this fact.

Polyvinyl alcohol-engineering cementitious composites (PVA-ECC) has been widely applied in bridge deck repairing or widening, the common practice for doing this is that a portion of a bridge is left open to traffic while the closed portion is constructed, which expose the early age PVA-ECC to the vehicle-induced vibrations. However, whether vehicle-induced vibrations affect the tensile performance of early age PVA-ECC remains unknow. The purpose of this study was to conduct laboratory test programs on how much vehicle-induced vibrations during early ages affected the tensile performance of PVA-ECC. A self-improved device was used to simulate the vehicle-induced vibrations, and after vibrating with the designed variables, both a uniaxial tensile test and a grey correlation analysis were performed. The results indicated that: the effects of vehicle-induced vibrations on the tensile performance of early age PVA-ECC were significant, and they generally tended to be negative in this investigation. In particular, for all of the vibrated PVA-ECC specimens, the most negative age when vibrated occurred during the period between the initial set and the final set. We concluded that although vehicle-induced vibrations during the setting periods had no substantial effects on the inherent strain-hardening characteristics of PVA-ECC, the effects should not be ignored.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

Q-switched laser radiation at wavelengths of 355 nm, 532 nm, and 1064 nm from a Nd: YAG laser was used to generate plasma in laboratory air at the target surface made of compressed nano-silver particles of size 95 ± 10 nm. The emitted resonance spectra from the neutral silver at wavelengths of 327.9 nm and 338.2 nm indicate existence of self-reversal in addition to plasma self-absorption. Both lines were identified in emission spectra at different laser irradiation wavelengths with characteristic dips at the un-shifted central wavelengths. These dips are usually associated with self-reversal. Under similar conditions, plasmas at the corresponding bulk silver target were generated. The recorded emission spectra were compared to those obtained from the nano-material target. The comparisons confirm existence of self-reversal of resonance lines that emerge from plasmas produced at nano-material targets. This work suggests a method for recovery of the spectral line shapes and discusses practical examples. In addition, subsidiary calibration efforts that utilize the Balmer series Hα-line reveal that other Ag I lines at 827.35 nm and 768.7 nm are optically thin under variety of experimental conditions and are well-suited as reference lines for measurement of the laser plasma electron density.

In this research, the computational fluid dynamic (CFD) approach that has been used in wind power generation field was applied for the solution of the problems of local strong wind areas in railway fields, and the mechanism of wind generation was discussed. At the same time, the affectivity of the application of computational fluid dynamic approach to railway field was discussed. The problem of local wind that occurs on the railway line in winter was taken up in this research. A computational simulation for the prediction of wind conditions by LES was implemented and it was clarified that the local strong wind area is mainly caused by separated flows originating from the small‐scale terrain positioned at its upstream (at approximately 180.0 m above sea level). Meanwhile, the effects of the size of calculation area and spatial grid resolution on the result of calculation and the effect of atmospheric stability were also discussed. It was clarified that when the air flow characteristic of the separated flow originating from the small‐scale terrain (at altitude of approximately 180.0 m) targeted in this research is reproduced at high accuracy by computational simulation of wind conditions, approximately 10.0 m of spatial resolution of computational grid in horizontal direction is required. As a result of the computational simulation of wind conditions of stably stratified flow (Fr = 1.0), lee waves were excited at the downstream of the terrain over time. As a result, the reverse‐flow region lying behind the terrain that had been observed at a neutral time was inhibited. Consequently, local strong wind area was generated at the downstream of the terrain and the strong wind area passing through the observation mast was observed. By investigating the speed increasing rate of local strong wind area induced at the time of stable stratification, it was found that the wind was approximately 1.2 times stronger than what was generated at a neutral time.

Electrically conductive polymer composites are in high demand for modern technologies, however, the intrinsic brittleness of conducting conjugated polymers and the moderate electrical conductivity of engineering polymer/carbon composites have highly constrained their applications. In this work, super high electrical conductive polymer composites were produced by a novel hot embossing design. The polydimethylsiloxane (PDMS) composites containing short carbon fiber (SCF) exhibited an electrical percolation threshold at 0.45 wt%, and reached a saturated electrical conductivity of 49 S/m at 8 wt% of SCF. When reduced the sample thickness from 1.0 mm to 0.1 mm by the hot embossing process, a compression-induced percolation threshold occurred at 0.3 wt%, while the electrical conductivity was further enhanced to 378 S/m at 8 wt% SCF. Furthermore, the additional of a second nanofiller of 1 wt%, such as carbon nanotube or conducting carbon black further increased the electrical conductivity of the PDMS/SCF (8 wt%) composites to 909 S/m and 657 S/m, respectively. The synergy of the densified conducting filler network by the mechanical compression and the hierarchical micro-/nanoscale filler approach has realize super high electrical conductive yet mechanical flexible polymer composites for modern flexible electronics applications.

This work communicates results from optical emission spectroscopy following laser-induced optical breakdown at or near nanomaterial. Selected atomic lines of silver are evaluated for consistent determination of electron density. Comparisons are presented with Balmer series hydrogen results. Of particular interest are measurements free of self-absorption effects. For several silver lines, asymmetries are observed in the recorded line profiles. Electron densities of interest range from 0.5 to 3 × 10¹⁷ cm^-3, for 5 nanosecond Q-switched Nd:YAG radiation at wavelengths of 1064, 532, and 355 nm, and for selected silver emission lines including 328.0, 338.2, 768.7, and 827.3 nm, and the hydrogen alpha Balmer series line at 656.3 nm. Line asymmetries are presented for the 328.0 nm Ag I line that is measured following generation of the plasma due to multiple photon absorption. This work explores electron density variations for different irradiance levels, and reports spectral line asymmetry of resonance lines for different laser fluence levels.

Direct reprogramming of fibroblasts into induced cardiomyocytes (iCMs) holds a great promise for regenerative medicine and has been studied in several major directions. However, cell-cycle regulation, a fundamental biological process, has not been investigated during iCM-reprogramming. Here, our time-lapse imaging on iCMs, reprogrammed by Gata4, Mef2c, and Tbx5 (GMT) monocistronic retroviruses, revealed that iCM-reprogramming was majorly initiated at late-G1- or S-phase and nearly half of GMT-reprogrammed iCMs divided soon after reprogramming. iCMs exited cell cycle along the process of reprogramming with decreased percentage of EdU⁺/αMHC-GFP⁺ cells. S-phase synchronization post-GMT-infection could enhance cell-cycle exit of reprogrammed iCMs and yield more GFP^high iCMs, which achieved an advanced reprogramming with more expression of cardiac genes than GFP^low cells; however, S-phase synchronization didn’t enhance the polycistronic-MGT reprogramming, in which cell-cycle exit had been accelerated. In conclusion, post-infection synchronization of S-phase facilitated the early progression of GMT-reprogramming through a mechanism of enhanced cell-cycle exit.

For esophageal cancer patients treated with neoadjuvant chemoradiotherapy (nCRT), restaging using F-18-fluorodeoxyglucose (18F-FDG) positron emission tomography computed tomography (PET-CT) following nCRT can detect interval metastases, including liver metastases, in almost 10% of patients. However, in clinical practice, focal FDG liver uptake, unrelated to liver metastases, is observed after chemoradiotherapy. This radiation-induced liver injury (RILI) can potentially lead to overstaging. Liver radiation damage is also a concern during distal esophageal cancer radiotherapy due to proximity to the left liver lobe, typically included in the radiation field. Post-CRT, if FDG activity appears in the left or caudate liver lobes, thorough investigation is needed to confirm or rule out distant metastases. The increased FDG uptake in liver lobes post-CRT often presents a diagnostic dilemma. Distinguishing between radiation-induced liver disease and metastasis is vital for appropriate patient management, necessitating a combination of imaging techniques and an understanding of the factors influencing radiation response. Diagnosis involves identifying new foci of hepatic FDG avidity on PET/CT scans. Geographic regions of hypoattenuation on CT and well-demarcated regions with specific enhancement patterns on contrast-enhanced CT scan and MRI are characteristic of radiation-induced liver disease (RILD). Lack of mass effect on all three modalities (CT, MRI, PET) indicates RILD. Resolution of abnormalities on subsequent examinations also helps in diagnosing RILD. Moreover, it can also help to rule out occult metastases, thereby excluding those patients from further surgery who will not benefit from esophagectomy with curative intent.

Driven by mounting environmental apprehensions stemming from the over dependence on fossil fuels in energy and transportation sectors, extensive exploration into alternative energy sources, particularly biomass, has stimulated profound research on harnessing the potential of computational and mathematical techniques. This comprehensive survey delves into optimal models and strategies, unveiling their pivotal role in the design of biomass gasification processes.of hydrogen through biomass gasification. In this study, we aim to provide a comprehensive overview of the computational and mathematical techniques employed in optimizing biomass gasification processes, with a specific focus on enhancing hydrogen yield. Through an extensive literature review, various models and strategies will be examined, including thermodynamic analysis, kinetic modeling, reactor design, and process optimization. By uncovering the power of these techniques, we aim to contribute to the advancement of sustainable and efficient biomass utilization for the hydrogen-based future economy.This paper aims to provide an updated and comprehensive coverage of the investigations conducted on the potential of producing hydrogen from biomass through gasification. To achieve this, we incorporate the latest works that have utilized numerical modeling, simulation, optimization techniques, process heat integration, and co-generation in their studies. By encompassing these aspects, we aim to offer a broader and more in-depth re-appraisal of the subject matter. This will ensure that readers gain a holistic understanding of the advances made in the field and the potential for sustainable hydrogen production of biomass gasification.Through a meticulous re-appraisal and analysis of each subject, we can identify their respective strengths and areas that require further research effort. By thoroughly examining numerical modeling, simulation, optimization techniques, process heat integration, and co-generation, we can assess their effectiveness and applicability in the context of biomass gasification for hydrogen production. This analysis shed light on the areas where these techniques excel, as well as pinpoint limitations or gaps in current understanding. By identifying these areas, we can highlight the need for further research and development, enabling us to make significant advancements in biomass gasification processes and pave the way for a sustainable and efficient hydrogen-based future economy..

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

The plate heat exchanger (PHE) is a component that provides heat to be transferred from hot water to domestic cold water without mixing them with high efficiency. Over the lifetime of the PHE, cyclic pressures act on the brazing points and the plates, and this may lead to fatigue failure. The fatigue behaviour of the PHE, designed by using copper-brazed 316L stainless steel, was investigated in this study. First, the fatigue tests under the load ratio R = 0.1 were performed on the Vibrophore 100 testing machine to obtain the S-N curve of the analysed brazed joint. Based on the obtained experimental results, an appropriate material model of the analysed brazed joint has been created, which was validated with numerical calculation in the framework of a program code Ansys. A validated material model was then used for the subsequent numerical analysis of PHE. In order to carry out a numerical calculation using the finite element method (FEM), a 3D model of the heat exchanger was created based on the previous scanning of PHE-geometry. Thereafter, the geometry was parameterised, which allowed us to perform parametric simulations (monitoring different responses depending on the input geometry). Numerical simulations were carried out in the framework of the Ansys software, whereby the obtained results were analysed, and the responses were appropriately characterised according to previously determined load cases.

Aircraft heat exchangers play a crucial role in maintaining thermal balance and ensuring that essential components operate efficiently and safely. In this context, it is highly relevant to gain knowledge about the deterioration and the predominant damage mechanisms of these components. In this study, two different non-destructive methods are employed to analyze the damage initiation of a heat exchanger part during fatigue test. On the one hand, Acoustic Emission technique is employed using membrane-free microphones capable of capturing a broad bandwidth. The acoustic events were classified by a machine learning algorithm to determine their source and damage mechanisms. On the other side, Digital Image Correlation (DIC) allowed the measurement of the strain evolution along the test and more precisely, redistributions were considered as damage indicators. As a result, it was identified that AE served as early damage indicator as the cumulative number of events was in good agreement with the severity of the damage. With respect to classification two clear clusters ascribed to different type of events were identified. In the case of DIC, strain redistributions gave clear indications of damage or deterioration but at a later stage compared to AE

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

The aim of this study was to evaluate the emulsification properties of garlic water-soluble compounds (GWSC) after heat treatment (10 min at 95 °C) or pH adjustments (2.5, 3.5 and 7.8). After the various treatments, the extracts were used as such or filtrated (0.45 µm) and 10% soybean oil-in-water emulsions were prepared using low (0.48%) or high (6.55% wt/wt) extract concentrations. Whereas at low GWSC concentration, both heating or acidifying resulted in the formation of bigger oil droplet sizes (i.e. from d32=0.36 µm using unmodified extract, to d32=7–22 µm µm at pH 2.5 with or without extract filtration), the effects were opposite at the highest GWSC concentration. In the latter, heat treatment clearly reduced the droplet size as observed from the micrographs as well as the degree of creaming, though the occurrence of depletion and/or bridging flocculation was still strong. The acidification of the extract at this high GWSC concentration, significantly reduced the droplet size as observed from the micrographs but a strong flocculation was observed. Removal of protein aggregates, and possibly also saponin micelles from the extract, resulted in an obvious increase in emulsion droplet size. This research brings valuable insights on the study and utilisation of novel natural food emulsifiers from plant sources.

Climate and its fluctuations have wide-ranging impacts on the tourism industry. High temperatures, as a typical meteorological and climatic factor, influence tourists' travel intentions and spatial behavior. This study conducted a descriptive analysis and market trend analysis of Chinese tourism during periods of high temperatures, revealing several key findings. Firstly, tourists seeking respite from summer heat exhibit a preference for short-distance trips and resource-rich destinations. Secondly, heat-escape tourism products undergo changes over time, gradually shifting towards mountainous areas and waterfront locations. Furthermore, taking Shanghai Disneyland as a case study demonstrates that the holiday system holds greater significance than temperature constraints. Despite experiencing a significant decline in the quality of their tourist experience in high-temperature environments, long-distance travelers are not deterred from choosing pre-booked tourism products by sudden bouts of hot weather.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

Dairy cattle predicted by genomic breeding values to be heat tolerant are known to have less milk production decline and lower core body temperature increases in response to elevated temperatures. In a study conducted at the University of Melbourne’s Dookie Robotic Dairy Farm during summer, we identified the most 20 heat-susceptible and 20 heat-tolerant cows in a herd of 150 Holstein Friesian lactating cows based on their phenotypic responses (changes in respiration rate, surface body temperature, panting score, and milk production). Hair samples were collected from the tip of the cows' tail following standard genotyping protocols. The results indicated variation in feed saved and HT genomic estimated breeding values (GEBVs) (P≤0.05) across age, indicating a potential for their selection. As expected, the thermotolerant group had higher GEBVs for HT and feed saved but lower for milk production. In general, younger cows had superior GEBVs for Balanced Performance Index (BPI), Type Weighted Index (TWI) and Australian Selection Index (ASI), whilst older cows were superior in fertility, feed saved (FS) and HT. The study demonstrated highly significant (P≤ 0.001) negative correlations (-0.28 to -0.74) between HT and GEBVs for current Australian Dairy cattle selection indices (BPI, TWI, ASI, HWI) and significant (P≤ 0.05) positive correlations between HT and GEBVs for traits like FS (0.45) and fertility (0.25). Genomic selection for HT will help improve cow efficiency and sustainability of dairy production under hot summer conditions. However, a more extensive study involving more lactating cows across multiple farms is recommended to confirm the associations between the phenotypic predictors of HT and GEBVs.

Near space environment is the airspace at an altitude of 20 km-100 km, where complex conditions such as low temperature, low pressure, high wind speed and solar radiation exist. As one of the important meteorological parameters, temperature is crucial for space activities, but the influence of the complex environment makes the error of conventional temperature measurement methods large. Therefore, a new microbridge temperature sensor was designed that can reduce solar radiation and achieve a fast response. And through simulation analysis, the three factors influencing the temperature errors of Joule heat, solar radiation heat and aerodynamic heat were investigated. And the influence of temperature error is reduced by optimizing the installation position of the sensor. Through the temperature error model, the error value in the actual measurement value is removed, to realize the high accuracy detection of near-space temperature.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

Steel is one of the essential materials in the world's civilization. It is essential to produce many products such as pipelines, mechanical elements in machines, vehicles, profiles, and beam sections for buildings in many industries. Until the '50s of the 20th century, steel products required a complex process known as ingot casting; for years, steelmakers focused on developing and simplifying this process. The result was the con-tinuous casting process (CCP); it is the most productive method to produce steel. The CCP allows producing significant volumes of steel sections without interruption and is more productive than the formal ingot casting process. The CCP begins by transferring the liquid steel from the steel-ladle to a tundish. This tundish or vessel distributes the liquid steel, by flowing through its volume, to one or more strands having wa-ter-cooled copper molds. The mold is the primary cooling system, PCS, solidifying a steel shell to withstand a liquid core and its friction forces with the mold wall. Further down the mold, the rolls drive the steel section in the SCS. Here the steel section is cooled, solidifying the remaining liquid core, by sprays placed in every cooling segment all around the billet and along the curved section of the machine. Finally, the steel strand goes towards a horizontal-straight free-spray zone, losing heat by radiation mechanism, where the billet cools down further to total solidification. A moving torch cutting-scissor splits the billet to the desired length at the end of this heat-radiant zone.

Understanding the mechanism for heat tolerance is important for the hot pepper breeding program to develop heat-tolerant cultivars in changing climate. This study was conducted to investigate physiological and biochemical parameters related to heat tolerance and to determine leaf heat damage levels critical for selecting heat-tolerant genotypes. Seedlings of two commercial cultivars, heat-tolerant ‘NW Bigarim’ (NB) and susceptible ‘Chyung Yang’ (CY), were grown in 42 °C for ten days. Photosynthesis, electrolyte conductivity, proline content were measured among seedlings during heat treatment. Photosynthetic rate was significantly reduced in ‘CY’ but not in ‘NB’ seedlings in 42 °C. Stomatal conductivity and transpiration rate was significantly higher in ‘NB’ than ‘CY’. Proline content was also significantly higher in ‘NB’. After heat treatment, leaf heat damages were determined as 0, 25, 50 and 75% and plants with different leaf heat damages were moved to a glasshouse (30–32/22–24 °C in day/night). The growth and developmental parameters were investigated until 70 days. ‘NB’ was significantly affected by leaf heat damages only in fruit yield while ‘CY’ was in fruit set, number and yield. ‘NB’ showed fast recovery after heat stress compared to ‘CY’. These results suggest that constant photosynthetic rate via increased transpiration rate as well as high proline content in heat stress condition confer faster recovery from heat damage of heat-tolerant cultivars in seedlings stages.

Plate fin-tube heat exchangers are widely used in air conditioning and refrigeration systems and other industry fields. Various errors made in the manufacturing process can result in the formation of an air gap between the tube and fin. Several numerical simulations were carried out for a symmetric section of plate fin-tube heat exchanger to study the influence of air gap on heat transfer under periodic flow conditions. Different locations and sizes of an air gap spanning 1/2 circumference of the tube were considered for the range of airflow velocities. Velocity and temperature fields for cases with air gap were compared with ideal thermal contact cases. Blocking of heat flow by the gap leads to the reduction of heat transfer rate. Fin discontinuity in the front of the tube causes the smallest reduction of the heat transfer rate in comparison to the ideal tube-fin contact, especially for thin slits. The rear gap position is the worst in the smallest gap range. Therefore, reversing the flow direction can lead to up to a 15% heat transfer increase, if mainly the rear gaps are present. The introduction of a thin slit in the front of the tube leads to convective heat transfer enhancement, which should be further investigated.

Over the last decade, there has been a growing interest in the use of a wide range of phytoadditives to counteract the harmful effects of heat stress in poultry. Willow (Salix spp.) is a tree with a long history. Among various forms, willow bark is an important natural source of salicin, β-O-glucoside of saligenin, but also of polyphenols (flavonoids and condensed tannins) with antioxidant, antimicrobial and anti-inflammatory activity. In light of this, the current review presents some literature data aiming to: (1) describe the relationship between heat stress and oxidative stress in broilers, (2) present or summarize literature data on the chemical composition of Salix species, (3) summarize the mechanisms of action of willow bark in heat-stressed broilers, (4) present different biological effects of the extract of Salix species in different experimental models.

The widely adopted temperature for solid solution heat treatment (ST) for the conventionally fabricated Inconel 718 is 1100 °C for a hold time of 1 h or less. This ST scheme is however not enough to dissolve Laves and annihilate dislocations completely in samples fabricated with Laser metal powder bed fusion (L-PBF) additive manufacturing (AM)-Inconel 718. In spite this, the highest hardness obtained after aging for ST temperatures (970 - 1250 °C) is at 1100 °C/1h [1]. The unreleased residual stresses in the retained lattice defects are potentially affecting other properties of the material. Hence, this work aims to investigate if a longer hold time of ST at 1100 °C will lead to complete recrystallization while maintaining the strength after aging or not. For this study, L-PBF-Inconel 718 samples were ST at 1100 °C at various hold times (1, 3, 6, 9, 16 or 24 h) and aged to study the effects on microstructure and hardness. In addition, a sample was directly aged to study the effects of bypassing ST. The samples (ST and aged) gain hardness by 43 – 49 %, depending on hold time. A high density of annealing twins evolved during 3 h of ST and the quantity only slightly varies for longer ST.

Nanofluids are a novel class of heat transfer fluid that plays a vital role in industries. In mathematical investigations, these fluids are modeled in terms of traditional integer-order partial differential equations (PDEs). It is recognized that traditional PDEs cannot decode the complex behavior of physical flow parameters and memory effects. Therefore, this article intends to study the mixed convection heat transfer in nanofluid over an inclined vertical plate via fractional derivatives approach. The problem in hand is modeled in connection with Atangana-Baleanu fractional derivatives without singular and local kernel having strong memory. The human blood is considered as base fluid dispersing carbon nanotube (CNTs) (single-wall carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes(MWCNTs )) into it to form blood-CNTs nanofluid. The nanofluids are considered to flow in a saturated porous medium under the influence of an applied magnetic field. The exact analytical expressions for velocity and temperature profiles are acquired using the Laplace transform technique and plotted in various graphs. The empirical results indicate that the memory effect decreases with increasing fractional parameters in the case of both temperature and velocity profiles. Moreover, the temperature profile is higher for blood-SWCNTs by reason of higher thermal conductivity whereas, this trend is opposite in case of velocity profile due densities difference.

This paper emphasises on the analogous modelling of hardwood (Acacia) pyrolysis. The effect of physical characteristics of hardwood chips on the pyrolysis is examined through the conservation of solid mass fraction of biomass. The chip size of G30 and G50 are used in the pyrolysis reactor. In the analogous situation, the fixed bed is assumed to be a wooden slab with a porosity equivalent to the voidage of bed. The bulk density, the length of the bed and the porosity are some of the physical attributes of a fixed bed used to determine the variation of solid mass of the hardwood across the fixed bed. The four-temperature sensors separated from each other by 80 mm are used to determine the temperature along the length of the pyrolysis unit. The heating element of 2 kWe is used to initiate the pyrolysis of biomass. The experiments are conducted in three different stages. The ONORM standard chips, G30 and G50, and the combination of them are separately pyrolysis to determine the validity of a model for different sizes of chips. The proposed model is also used to establish the relationship between the kinetics of pyrolysis and decomposition of the hardwood.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

This paper predict and effectively control the temperature distribution of the steady-state and transient states of anisotropic four-layer composite materials online, knowing the density, specific heat, heat conductivity and thickness of the composite materials. Based on the transfer function, a mathematical model was established to study the dynamic characteristics of heat transfer of the composite materials. First of all, the Fourier heat transfer law was used to establish a one-dimensional Fourier heat conduction differential equation for each composite layer, and the Laplace transformation was carried out to obtain the system function. Then the approximate second-order transfer function of the system was obtained by Taylor expansion, and the Laplace inverse transformation was carried out to obtain the transfer function of the whole system in the time domain. Finally, the accuracy of the simplified analytical solutions of the first, second and third order approximate transfer functions was compared with computer simulation. The results showed that the second order approximate transfer functions can describe the dynamic process of heat transfer better than others. The research on the dynamic characteristics of heat transfer in the composite layer and the dynamic model of heat transfer in composite layer proposed in this paper have a reference value for practical engineering application. It can effectively predict the temperature distribution of composite layer material and reduce the cost of experimental measurement of heat transfer performance of materials.

Carbonous nanomaterials are promising additives for composite coatings for heat-dissipation materials because of their excellent thermal conductivity. Here, copper/carbonous nanomaterial composite coatings were prepared using nanodiamond (ND) as the carbonous nanomaterial. The copper/ND composite coatings were electrically deposited onto copper substrates from a continuously stirred copper sulfate coating bath containing NDs. NDs were dispersed by ultrasonic treatment, and the initial bath pH was adjusted by adding sodium hydroxide solution or sulfuric acid solution before electrodeposition. The effects of various coating conditions—the initial ND concentration, initial bath pH, stirring speed, electrical current density, and the amount of electricity—on the ND content of the coatings were investigated. Furthermore, the surface of the NDs was modified by hydrothermal treatment to improve ND incorporation. A higher initial ND concentration and a higher stirring speed increased the ND content of the coatings, whereas a higher initial bath pH and a greater amount of electricity decreased it. The electrical current density showed a minimum ND content at approximately 5 A/dm². Hydrothermal treatment, which introduced carboxyl groups onto the ND surface, improved the ND content of the coatings. A copper/ND composite coating with a maximum of 3.85 mass% ND was obtained.

Regional heat capacity change is calculated from the ratio between the addition or subtraction of heat (ΔQ) with the increase or decrease in temperature (ΔT) region. The purpose of this study is to calculate the regional heat capacity change due to the changes of land cover composition with forest, shrubs, oil palm plantation and bare soil using Landsat-5 TM satellite data on 1994, 2000 and 2010. Total area that used on ​​this study is 12971 ha. In 1994-2000, 4 % of forest area and 2% shrubs were increased, followed by additional of biomass forest 4.01 tons/ha and 2.83 tons/ha for shrubs. The increased of forest area and biomass (tons/ha) caused by forest and shrubs growth processing towards climax that added the canopy volume. So that, the regional heat capacity in 1994 amounted 19384 MJC^o-1 increased to 19929 MJC^o-1 in 2000. Data observation for 2000-2010 showed that forest area decreased by 66% due to forest’s clearing into oil palm plantations (47%), shrubs (8%) and bare soil (11%). But, plant’s biomass continue to increased, i.e 1.48 ton/ha for forest, 2.73 tons/ha for shrubs and 4.63 tons/ha for bare soil. Before 2000, there was no land cover by oil palm plantations, so the increasing rate from this land was the biggest than the three other lands, amounting to 122.29 tons/ha. Decreasing in the percentage of forest area does not cause a decrease in the heat capacity of the region. Intensive maintenance on oil plam plantation such as water management, fertilizer and planting space made it biomass productivity and ability to save the heat is greater than the forest. As the result, in 2010 regional heat capacity increased to 22508 MJC^o-1.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

The urbanization effects on land surface phenology (LSP) have been investigated by many studies, but few studies focused on the temporal variations of urbanization effects on LSP. In this study, we used the MODIS EVI, MODIS LST data and China’s Land Use/Cover Datasets (CLUDs) to investigate the temporal variations of urban heat island intensity and urbanization effects on LSP in Northeast China during 2001–2015. Land surface temperature (LST) and phenology differences between urban and rural areas represented the urban heat island intensity and urbanization effects on LSP, respectively. Mann-kendall nonparametric test and Sen's slope were used to evaluating the trends of urbanization effects on LSP and urban heat island intensity. The results indicated that the average land surface phenology (LSP) during 2001–2015 was characterized by high spatial heterogeneity. The start of the growing season (SOS) in old urban area had become earlier and earlier than rural area and the differences of SOS between urbanized area and the rural area changed greatly during 2001–2015 (−0.79 days/year, p < 0.01). Meanwhile, the length of the growing season (LOS) in urban and adjacent areas had become increasingly longer than rural area especially in urbanized area (0.92 days/year, p < 0.01), but the differences of the end of the growing season (EOS) between urban and adjacent areas did not change significantly. Next, the UHII increased in spring and autumn during the whole study period. Moreover, the correlation analysis indicated that the increasing urban heat island intensity in spring contributed greatly to the increases of urbanization effects on SOS, but the increasing urban heat island intensity in autumn did not lead to the increases of urbanization effects on EOS in Northeast China.

Modelling water vapour flow, heat transfer and porosity in porous adsorbent is somewhat challenging simulation problem. Primary macroscopic water vapour flow models, such as Darcy's law, fail to predict the pressure drop entirely correctly for the reason that many of flow parameters not considered because of the simplifications that remain made for the multi-scale structure of the porous adsorbents. For one to develop a good physical understanding of such water vapour flows and the accuracy of existing 3D simulation models, there is a need for some accurate 3D geometry to be studied. This present work describes two-phase water vapour flow and adsorption/ desorption performed on porous adsorbent by a Dynamic vapour sorption (DVS). The CFD simulation results are associated with experiments results. It is decided that for such complex porous adsorbent CFD simulation problems the use of COMSOL Multiphysics and SolidWorks flow simulation will be utilised.

The paper is focused on researching the behavior of heating companies in connection with current developments in the electricity market and flexibility in the context of market behavior. The work assesses the increase in profitability through the creation of a technical-economic model using an objective function with profit maximization. The paper objective is presented the procedure and methodology for creating a model using the basic scheme of production processes integrated into the system platform. The result of the work is a comparative analysis of modelled cases of implemented operation deployment according to a defined period and modelling modes in selected time series. The description of individual outputs demonstrates the economic advantage of using combinations of modes of combined electricity and heat production, and non-combined electricity and heat production, including the use of the heat suppression mode because of overproduction of electricity.

Successful geophysical exploration works in Gucheng-Yaxi area located in Gaochun District, Jiangsu province, China, have been limited partly due to complex geological condition of the area and high artificial noise in data acquired using electrical and electromagnetic methods. In this work, we deployed the new anti-interference spread spectrum induced polarization method (SSIP) and audio magnetotellurics (AMT) method to detect a copper-polymetallic deposit in the area. Two-dimensional (2D) inversion results at Gucheng-Yaxi Area revealed a high chargeability anomalous zone on SSIP profile that coincided with a zone of moderate resistivity located between two resistor bodies on AMT profile. A follow up 1200 meters drill hole was established at this high chargeability-moderate resistivity zone which encountered polymetallic (copper, lead, zinc, gold and silver) mineralization at the depth ≥ 400 m. Drill hole data analysis showed that mineralization occurs interspaced in marble rock mass at varies depth. Furthermore, several low resistivity-weak chargeability sections were revealed and inferred attributed to Cretaceous sediments and faults. These faults are thought to have played critical role in the polymetallic mineralization genesis. In summary, this work demonstrated the successful of application of SSIP and AMT at detecting a metallic deposit in an area with high artificial noise. Hence the geophysical prospection potential of Gucheng-Yaxi area is great.

Earthquake-triggered landslides are one of the most significant hazards worldwide. These landslides, involving small or large volumes, can develop in debris flow or avalanche with high mobility and long-runout distance. The motion processes of this kind of landslide also quite complicated. This study reproduced the motion processes of two landslides using the LS-RAPID program. The Aso Bridge landslide occurred on April 16, 2016, with rapid and long-runout distance characteristics. The Kataragai landslide occurred on April 9, 2018, travelling with flow-like behavior. Through field investigations and laboratory experiments, features and mechanical parameters of these two landslides were obtained. In the LS-RAPID program, the pre-failure models and motion processes of these two landslides were established and reproduced. Results indicated that sliding speed and travelling morphology at different intervals were considered as two indicators to describe their motion process. However, while sliding speed of these two landslides have significant differences with sliding speeds of actual landslides, the final morphologies after failure were consistent with those observed in the field investigation.

Familial Mediterranean fever (FMF) is a systemic autoinflammatory disorder caused by inherited mutations in the MEFV (Mediterranean FeVer) gene located on chromosome 16 (16p13.3) and coding pyrin protein. Despite the existing data on MEFV mutations, the exact mechanism of their effect on the development of pathological processes leading to autoinflammation observed in FMF, remains unclear. Induced pluripotent stem cells (iPSCs) are considered an important tool for studying the molecular genetic mechanisms of various diseases due to their ability to differentiate into any cell type, including macrophages, which contribute to the development of FMF. In this study, we developed iPSCs of an Armenian patient with FMF having M694V, p.(Met694Val) (c.2080A&gt;G, rs61752717) pathogenic mutation in exon 10 of the MEFV gene. As a result of direct differentiation, macrophages expressing CD14 and CD45 surface markers were obtained. In addition, we found that the morphology of patient macrophages derived from iPSCs with MEFV mutation was significantly different from that of differentiated from iPSCs of a healthy donor carrying wild-type MEFV gene.

The exceptional performance of graphene has driven the advancement of its preparation technique and application. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure were subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy, and energy-dispersive X-ray spectroscopy. The periodic linear array structure were observed by Scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that the high quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100°C and 240°C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

The availability of multi-rotor UAVs with lifting capacities of several kilograms, allows for a new paradigm in atmospheric measurement techniques, i.e. the integration of research-grade sonic anemometers for airborne turbulence measurements. With their ability to hover and move very slowly, this approach yields an unrevealed flexibility compared to mast-based sonic anemometers, for a wide range of boundary layer investigations that require an accurate characterization of the turbulent flow. For an optimized sensor placement, potential disturbances by the propeller-induced flow (PIF), as well as the potential impact of the sensor weight and angular momentum on the flight performance in the case of a boom-mounted sensor, have to be considered.

Plant cells are omnipotent and breeding of new varieties can be achieved by protoplast fusion. Such fusions can be achieved by treatment with poly(ethylene glycol) or by applying an electric field. Microfluidic devices allow for controlled conditions and targeted manipulation of small batches of cells down to single cell analysis. To provide controlled conditions for protoplast fusions and achieve high reproducibility, we developed and characterized a microfluidic device to reliably trap few of Arabidopsis thaliana protoplasts and induced a cell fusion by controlled addition of poly(ethylene glycol) (PEG, with a molecular weight of 6000). Experiments were conducted to determine the survival rate of isolated protoplasts in our microfluidic system. Afterwards, PEG induced fusion was studied. Our results indicate that the following fusion parameters had significant impact on the fusion efficiency and duration: PEG concentration, osmolarity of solution, and flow velocity. PEG concentration below 10% led to only partial fusion. Osmolarity of the PEG fusion solution was found to strongly impact the fusion process; complete fusion of two source cells sufficiently took part in slightly hyper osmotic solutions, whereas iso-osmotic solutions led to only partial fusion at 20% PEG concentration. We observed accelerated fusion for higher fluid velocities. Up to this study, it was common sense that fusion is one directional, i.e. once two cells were fused into one cell they stay fused. Here, we present for the first time reversible fusion of protoplasts. Our microfluidic device paves the way to a deeper understanding on the kinetics and processes of cell fusion.

RNA, as an important substance for regulating biological growth and development, has significant implications for visualization research. However, many spontaneously fluorescent substances in plants greatly interfere with the effectiveness of plant bioimaging. Aggregetion- induced emission luminogens (AIEgens), due to their luminescent properties, tunable molecular size, high fluorescence intensity, good photostability, and low cell toxicity, have been widely applied in the animal and medical fields. We have found that AIEgens have great potential as RNA fluorescent probes for efficient imaging in plants. In this review, we first introduce several common RNA labeling forms and point out their pros and cons. We briefly describe the development of AIEgens and the AIE mechanism, and then present various practical applications of AIEgens, including detailed examples of their use as biological markers. To further promote the application of AIE in the field of RNA, we suggest the use of AIEgens to modify target RNA via techniques such as click chemistry or CRISPR/Cas, to achieve RNA visualization in plants. highly possible to modify target RNA with AIEgens in vivo for RNA visualization.

Laser-induced periodic surface structures (LIPSS) have gained significant attention due to their ability to modify the surface morphology of materials at the micro-nanoscale and show great promise for surface functionalization application. In this study, we specifically investigate the formation of LIPSS in silicon substrates and explore their impact on Surface-Enhanced Raman Spectroscopy (SERS) applications. This study reveals a stepwise progression of LIPSS formation in silicon, involving three distinct stages of LIPSS: 1) integrated Low-Spatial-Frequency LIPSS (LSFL) and High-Spatial-Frequency LIPSS (HSFL), 2) principally LSFL and 3) LSFL at the edge of the irradiated spot, elucidating the complex interplay between laser fluence, pulse number, and resulting surface morphology. Furthermore, from an application standpoint, these high-quality multi-scale periodic patterns lead to the next step of texturing the entire silicon surface with homogeneous LIPSS for SERS application. The potential of LIPSS-fabricated silicon substrates for enhancing SERS performance is investigated using thiophenol as a test molecule. The results indicate that the Au-coated combination of LSFL and HSFL substrate showcased the highest enhancement factor (EF) of 1.38 × 10^6. This pronounced enhancement is attributed to the synergistic effects of Localized Surface Plasmon Resonance (LSPR) and Surface Plasmon Polaritons (SPPs), intricately linked to HSFL and LSFL characteristics. These findings contribute to understanding LIPSS formation in silicon and their applications in surface functionalization and SERS, paving the way for sensing platforms.

The theory of electron spin has been proposed for a century, but the study of quantum effects in biological molecules is still in its infancy. Chirality-induced spin selectivity (CISS) is a very modern theory that can explain many biochemical phenomena. In this paper, we propose a new theoretical model based on CISS theory and quantum chemistry theory, which can well explain the theoretical explanation of the chiral selectivity of chiral proteins. Moreover, this theory can predict the spin state of corresponding chiral molecules. Taking L-DOPA and AADC enzyme as examples, this theoretical model solves the theoretical explanation of AADC enzyme's chiral catalysis selectivity problem and successfully predicts the spin state of L-DOPA and D-DOPA's valence electrons.

Laser additively manufactured (LAM) Ti–6Al–4V alloy has huge application potential in aerospace structural parts such as turbine blades. However, there are few studies on the fatigue properties of such LAM parts under vibration loading, particularly with regard to anisotropy. In this paper, vibration fatigue properties of LAM Ti-6Al-4V by laser melted deposition process were investigated along the transversely deposited (TD) direction and parallelly deposited (PD) direction. Through the first-order bending vibration experiments, LAM Ti-6Al-4V alloy exhibits obvious anisotropic fatigue properties and significant dispersion in fracture position. The fracture morphology analysis reveals that the vibration fatigue failure was mainly dominated by the LAM process-induced defects and the microstructure. For the LAM samples without defects at crack initiation sites, the fatigue behavior is controlled by the prior β columnar grains with preferential orientation, which leads to enhanced fatigue crack propagation resistance for the PD samples. For the LAM samples with defects at initiation sites, having lower fatigue lives, the fatigue anisotropy strongly depends on the projection area of the lack-of-fusion defects relative to the loading direction, resulting in better fatigue performance for the TD samples.

Human induced pluripotent stem cell (hiPSC)-derived neural cells have been used at the preclinical stage of drug development. As previously reported, hiPSC-derived neurons exhibit greater tolerance to excitotoxicity than that of primary cultures of rodent neurons; however, the underlying mechanisms remain unknown. We therefore investigated the functions of L-glutamate (L-Glu) transporters, the most important machinery used to maintain low extracellular L-Glu concentrations, in hiPSC-derived neural cells. We also clarified the contribution of each L-Glu transporter subtype. At 63 days in vitro (DIV), we detected neuronal circuit functions in hiPSC-derived neural cells by a microelectrode array system (MEA). Exposure to 100 μM L-Glu for 24 hrs did not affect the viability of these 63 DIV neural cells. Pharmacological inhibition of excitatory amino acid transporter 1 (EAAT1) and EAAT2 blocked almost 100% of L-Glu uptake. In this condition, L-Glu exposure dramatically decreased cell viability. These results suggest that in hiPSC-derived neural cells, EAAT1 and EAAT2 are predominant L-Glu transporters, and their uptake potentials are stronger than those of primary cultures of rodent neurons. Furthermore, hiPSC-derived neural cells may be useful for screening drugs that target L-Glu transporters.

Abstract: Arranged patterns obtained by ultrafast laser processing on the surface of Ti/Cu/Ti/Si and Ti/Zr/Ti/Si thin film systems are reported. Two differently designed multilayer thin films, Ti/Cu/Ti/Si and Ti/Zr/Ti/Si, were deposited on silicon by the ion sputtering method. The bioactive surfaces on these systems involve the formation of laser-induced periodic surface structures (LIPSS) in each of the laser-written lines of mesh patterns on 5x5 mm areas. The formation of nano- and micro-patterns with an ultra-thin oxide film on the surfaces was used to observe the effects of morphology and proliferation of the MRC-5 cell culture line. To determine whether Ti-based thin films have a toxic effect on living cells, an MTT assay was performed. The relative cytotoxic effect as a percentage of surviving cells showed that there was no difference in cell number between the Ti-based thin films and the control cells. There was also no difference in the viability of the MRC-5 cells, except for the Ti/Cu/Ti/Si system, where there was a slight 10% decrease in cell viability.

The primary cilium plays critical roles in homeostasis and development of neurons. Recent studies demonstrate that cilia length is regulated by the metabolic state of cells, as dictated by processes such as glucose flux and O-GlcNAcylation (OGN). The study of cilia length regulation during neuron development, however, has been an area left largely unexplored. This project aims to elucidate the roles of O-GlcNAc in neuronal development through its regulation of the primary cilium. Here, we present findings suggesting that OGN levels negatively regulate cilia length on differentiated cortical neurons derived from human-induced pluripotent stem cells. In neurons, cilia length increased significantly during neurons maturation (after day 35), while OGN levels began to drop. Long-term perturbation of OGN via drugs, which inhibit or promote its cycling, during neuron development also have varying effects. Diminishing OGN levels increases cilia length until day 25, when neural stem cells expand and undergo early neurogenesis, before causing cell cycle exit defects and multinucleation. Elevating OGN levels induces greater primary cilia assembly but ultimately results in the development of premature neurons, which have higher insulin sensitivity. These results indicate that OGN levels and primary cilia length are jointly critical in proper neuron development and function. Understanding the interplays between these two nutrient sensors, O-GlcNAc and the primary cilium, during neuron development is important in paving connections between dysfunctional nutrient-sensing and early neurological disorders.

Viroids are known the smallest plant pathogens, and although their genome sequences do not encode proteins, they can cause disease in economically important crops. In order to control viroid diseases and mitigate their damage, genetic resources used for breeding of the viroid-resistant crop have been searched, but the practical resistant trait has not been found in almost all viroid-crop combinations, as well as the tolerant trait. Due to the difficulty in exploiting naturally occurring resistance or tolerance, various effective strategies have been devised to control viroid diseases using non-transforming or transforming techniques. Meanwhile, extensive findings related to viroid resistance and tolerance may lead to confer resistance or tolerance to viroid infection by combining with the recently emerged new technologies (e.g., spray-induced gene silencing and genome-editing technologies), which are believed to be more environmentally viable and acceptable to the general public than previously reported approaches. In particular, some genome-modified crops produced by the latter technology are already on the market. In this review, we comprehensively summarize the current status about investigation of naturally occurring genetic traits for viroid resistance and tolerance, accumulating knowledge about host factors involved in viroid pathogenicity, and various basic technologies developed to try to possible viroid disease control strategies. Furthermore, we discuss prospects and challenges for the achievement of more effective, practical, and sustainable disease control of viroid.

Limb girdle muscular dystrophies (LGMD), caused by mutations in 29 different genes, are the fourth most prevalent group of genetic muscle diseases, leading to progressive weakness and atrophy of the skeletal muscles. Although the link between LGMD and their genetic origins has been determined, LGMD still represent an unmet medical need. In this paper, we describe a platform for modeling LGMD based on the use of human induced pluripotent stem cells (hiPSC). Thanks to the self-renewing and pluripotency properties of hiPSC, this platform provides an alternative and renewable source of skeletal muscle cells (skMC) to primary, immortalized or overexpressing cells. We report that skMC derived from hiPSC express the majority of the genes and proteins causing LGMD. As a proof of concept, we demonstrate the importance of this cellular model for studying LGMDR9 by evaluating disease-specific phenotypes in skMC derived from hiPSC obtained from four patients.

Phytophthora. infestans is a well known late blight causing oomycetes pathogen. It evolves and adapts to the host background and new fungicide molecules rapidly within a few years of their release, may be due to the predominance of transposable elements in its genome. Frequent and huge applications of fungicides cause environmental concerns. Here we developed target specific RNA interference based molecules, that are capable of effectively reducing the late blight infection. cDNA microarray expression data was used for the selection of genes involved in the early stage of infection process, sporulation etc. The in vitro synthesis of double stranded RNA molecule, targeting SDH, EF-1α, GPI-HAM344, PLD-3 and HSP-90 encoding genes revealed the reduction in growth, sporulation and symptom expression, which were subsequently assessed by culture bioassay, detached leaf assay and topical application methods. The multiple genes targeted dsRNA nano clay sprayed plants showed enhanced disease resistance (4% disease severity) and least sporulation (<1x103), compared to naked dsRNA spray. Use of nano clay was assumed to be involved in the effective delivery, protection and boosting the action of RNAi in potato plants. A significant difference in the growth, sporulation count, disease severity and reduced expression of the genes and confocal microscopy imaging authenticates the effects of SIGS on late blight disease progression. Our research demonstrated that topical dsRNA nano clay spray under the open-air environment could be an alternative to chemical fungicides and transgenic approaches as a novel plant protection strategy for late blight in an environmentally friendly manner.

Objective: To assess the functionality of the affected upper limb in children diagnosed with hemiplegia aged between 4 and 8 years after applying low-intensity modified constraint-induced movement therapy(mCIMT). Methods: Prospective case series study. A mCIMT protocol was applied for five weeks, with two hours of containment per day. The study variables were: quality of movement of the upper limb, spontaneous use, participation of the affected upper limb in activities of daily living, dynamic joint position, grasp-release action, grasp strength, supination and extension elbow movements. Four measurements were performed, using the QUEST scale, the SHUEE Evaluation, a hand dynamometer and a goniometer. Results: The sample was composed of 8 children with moderate manual ability. Statistically significant differences were detected in all the studied variables (p&lt;0.05). The greatest increase occurred in spontaneous use from assessment 1-4 (p = 0.01), reaching 88.87% active participation in bimanual tasks. The quality of movement of the upper limb obtained a significant value due to the increase in dissociated movements and grasp (p = 0.01). Conclusion: A low dose (50 hours) of mCIMT increased the functionality of children diagnosed with congenital hemiplegia between 4 and 8 years of age with moderate manual ability.

Aberrant neutrophil extracellular trap (NET) formation and the loss of barrier integrity in inflamed intestinal tissues have long been associated with inflammatory bowel disease (IBD). However, whether NETs alter intestinal epithelium permeability during colitis remains elusive. Here, we demonstrated that NETs promote the breakdown in intestinal barrier function for the pathogenesis of intestinal inflammation in mouse models of colitis. NETs were abundant in the colon of mice with colitis experimentally induced by dextran sulfate sodium (DSS) or 2,4,6-trinitrobenzene sulfonic acid (TNBS). Analysis of the intestinal barrier integrity revealed that NETs impaired gut permeability, enabling the initiation of luminal bacterial translocation and inflammation. Furthermore, NETs induced the apoptosis of epithelial cells and disrupted the integrity of tight junctions and adherens junctions. Intravenous administration of DNase I, an enzyme that dissolves the web-like DNA filaments of NETs, during colitis restored the mucosal barrier integrity which reduced the dissemination of luminal bacteria, and attenuated intestinal inflammation in both DSS and TNBS models. We conclude that NETs serve a detrimental factor in the gut epithelial barrier function leading to the pathogenesis of mucosal inflammation during acute colitis.

Globally 30% of landslides occur in the northeastern part of India [1]. One of the major earthquake events in Sikkim, India occurred on 18th September 2011 (Mw 6.9) led to over 300 landslides and 122 human deaths [2]. These landslides not only controlled by natural disasters but initiated due to human activities. The present study considered Lungchok landslide occurred in south district of Sikkim due to 2011 seismic event. The study focused on the failure mechanism of the landslide based on finite element analysis by adopting eight different cases. The deformation characteristic was investigated for dry and saturated slope conditions under static and dynamic behavior considering vehicle loads using GeoStudio software. The FEM analysis has been carried out using load deformation and linear elastic. The analysis shows that the failure of the slope was not sudden due to the 2011 earthquake event, but progressive failure was observed with time and construction activity. The paper demonstrates that, an increase in infrastructure development including construction by hill cutting increased the initiation of landslide with soil erosion. The cracks developed after 2011 earthquake event led to further deformations during future disasters required effective stabilization measures.

The human degenerative cartilage has low regenerative potential. Chondrocyte transplantation offers a promising strategy for cartilage treatment and regeneration. Currently chondrogenesis using human pluripotent stem cells are accomplished using human recombinant growth factors. Here, we differentiated human induced pluripotent stem cells (hiPSCs) into chondrocytes and cartilage pellet using minicircle vectors. Minicircles are used as a non-viral gene delivery system for gene therapy in various diseases. Non-viral gene delivery can produce growth factors without integrating into the host genome. Minicircle vectors containing bone morphogenetic protein 2 (BMP2) and transforming growth factor, beta 3 (TGFβ3) were successfully generated and delivered to hiPSC-derived outgrowth (OG) cells. Cell pellets generated using minicircle-transfected OG cells successfully differentiated into chondrogenic lineage. Chondrogenic pellets transfected with growth factor-encoding minicircles effectively recovered osteochondral defect in rat models. Taken together, this work shows the potential application of minicircles in cartilage regeneration using hiPSCs.

This study examines the effects of the δ phase and annealing twins on the hardness, Charpy impact toughness, and tensile properties of Inconel 718 fabricated using L-PBF. Two heat treatment methods, involving solid solution and precipitation hardening, were utilized. The δ phase was formed through solid solution heat treatment at 980C for 1 hour while annealing twins were generated at 1100C for 3 hours. After precipitation hardening, specimens with a higher concentration of  precipitates exhibited increased ultimate tensile strength (13%), yield strength (27%), and hardness (12%) compared to those with annealing twins. This can be attributed to the smaller grain size, subgrains, and δ precipitates, which contribute to the differences in mechanical strength. On the contrary, specimens with annealing twins showed significantly higher impact toughness (4 times) and ductility (twice) than those with δ precipitates. This is caused by the formation of  precipitates, which serve as sites for void formation and crack propagation, leading to a decrease in plasticity due to lattice mismatches with the matrix. Microstructural, compositional, phase, crystallographic, and fractographic analyzes were performed using OM, SEM, TEM and XRD techniques to identify the factors responsible for the variations in the measurements. The results demonstrate that the heat treatment method involving annealing twins significantly improves the ductility of Inconel 718 while maintaining the required mechanical strength.

To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

Measurement of Globe temperature is essential for investigating thermal comfort in street canyon. Globe thermometer is the most common instrument used to measure globe temperature (GT), however its application in scale models is still uncertain and not thoroughly investigated as of today. Therefore, this study is explicitly conducted to investigate globe thermometer measurements and proposed an improvised customization of the globe thermometer size to enhance reliability in scale models. The experiments were carried out outdoors using a typical street canyon model (scale 1:100) with East-West street orientation. The experiment presented a comparison between a low solar reflective street canyon (albedo of 0.4) and a high solar reflective canyon (albedo of 0.6) in terms of surface temperatures, heat flux and globe temperature. Furthermore, this study also investigated the influence of solar orientation on the globe temperature using both experimental using scale models and microclimatic modelling using ENVI-met. It is observed that although the surface temperatures are lower with high solar reflective canyon compared to that with low solar reflective canyon, GT is higher in high reflective canyon during daytime, which could be due to combined effect of direct radiation and shortwave reflection. However, for hours after the sun set, GT becomes lower (up to 1°C) in the case of high reflective canyon compared to low reflective canyon.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

A thermal system in very deep Lake Tazawa (maximum depth, 423 m) was investigated by estimating the heat budget. In the heat budget estimate, the net heat input at lake surface and the heat input by river inflow and groundwater inflow were considered. Then, the heat loss by snowfall onto lake surface was taken into account. Meanwhile, lake water temperature was monitored at 0.2 m to the bottom by mooring temperature loggers for more than two years. The heat storage change of the lake from the loggers was calibrated by frequent vertical measurements of water temperature at every 0.1 m pitch by a profiler with high accuracy (± 0.01 °C). The heat storage change (W/m2) obtained by the temperature loggers reasonably accords to that from the heat budget estimate. In the heat budget, the net heat input at lake surface dominates the heat storage change, but the significant heat loss by river inflow sporadically occurred, which is caused by the relatively large discharge from a reservoir in the upper region. How deep the vertical water circulation in the lake occurs in winter was judged by the differences between water temperatures at 0.2 m depth and bottom and between vertical profiles of dissolved oxygen over winter. It is strongly suggested that the whole water circulation does not occur every winter, if any, very weak.

Pool boiling is extensively utilized in various fields, such as electronics cooling, battery cooling, nuclear power plants, and chemical processing. In the process of temperature control through boiling, the generation and transportation of bubbles play a crucial role in calculating the heat transfer capacity of the system. Therefore, it holds immense significance to gain a profound understanding of the mechanisms underlying bubble formation, growth, and detachment. Currently, numerous mechanistic explanations and empirical correlations have been proposed to elucidate various parameters of bubbles during the boiling process. These findings were considered valuable references in selecting appropriate boiling media and designing efficient heating surfaces. To comprehensively present the progress of bubble formation and heat transfer during the boiling process, the forces exerted on the bubbles was highlighted in this article. And a meticulous review on bubble force analysis and correlation formulas pertaining to various relevant parameters (e.g. nucleation sites density, bubble growth rate, detachment diameter, detachment frequency) were conducted. This review article also were expected to provide a novel foundation for further exploration of enhanced boiling heat transfer.

Thermoelectric (TE) waste heat recovery has attracted significant attention over the past decades, owing to its direct heat-to-electricity conversion capability and reliable operation. However, methods of system-level TE design optimization for specific application systems have not been thoroughly investigated. This work theoretically studies the performance optimization and exergy analysis of TE systems for recovering waste heat from the exhaust ducts of a gas turbine power plant. A numerical tool has been developed to solve the coupled charge and heat current equations with temperature-dependent material properties and convective heat transfer at the interfaces. Our calculations show that at the optimum design with 50 % fill factor and 6-mm leg thickness made of state-of-the-art Bi2Te3 alloys, the proposed system can reach power output of 10.5 kW for the TE system attached on a 2 m-long, 0.5 x 0.5 m2-area exhaust duct with system efficiency of 5 % and material cost per power of 0.23 $/W. Moreover, our extensive exergy analysis reveals that only 1 % of the exergy content of the exhaust gas is exploited in this heat recovery process and the exergy efficiency of the TE system can reach 8 % with improvement potential of 85 %.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.