The regenerated magnesia-calcium brick samples that had added 0, 1.5, 3.0 wt.% aluminium oxide (Al2O3) were prepared by using spent magnesia-calcium bricks, fused magnesia and Al2O3 powder additive as the main raw materials. The phases, microstructures, room temperature and hot flexural strength, resistance to cement clinker corrosion and strength of coating adherence were investigated respectively. It indicated that the addition of Al2O3 increased mainly resulting in the content of tetracalcium aluminoferrite (C4AF) and tricalcium aluminate (C3A) increased in the regenerate samples. The bulk density, the room temperature flexural strength and the strength of coating adherence all increased, while the hot flexural strength and corrosion resistance both deteriorated along with the increase of Al2O3 addition. It was because that on the one hand the low melting point phases of C4AF and C3A improved the sinterability of the regenerated samples during the burning stage, on the other hand they melted or existed in liquid phase during the experimental temperature (1573 K and 1823 K) which degraded hot flexural strength and corrosion resistance, and enhanced the strength of coating adherence as the wettability of the liquid phase. The content of Al2O3 in the regenerated magnesia-calcium brick should not be higher than 1.1 wt.%, considering its room and high-temperature performances for cement rotary kiln.

Resistance training is beneficial to adults for improving muscle strength and reducing the body composition. Nevertheless, little is known regarding online resistance training on anthropometric parameters and muscular strength (MS) in overweight female adolescents. This study aimed to examine the effects of online resistance training on anthropometric parameters and muscular strength (MS) in overweight female adolescents. This prospective, single-center, single-blinded, randomized controlled study included 60 overweight female adolescents who were divided into a control group (n=30) and an intervention group (n=30). The intervention group performed online resistance training, which focused on body weight training of 12 components (4 sets, 12 repetitions) for 45 min, three times per week, for 12 weeks. The intensity of training was 65–75%. Anthropometric parameters, including body weight (BW), body mass index (BMI), body circumference measurements (BCM), and muscle strength (MS), were assessed. All parameters were measured at weeks 0, 8, and 12. Within-group and between-group comparisons were performed. The results revealed improvements in MS, BW, BMI, and BCM in the intervention group. However, chest circumference was not significant. These findings suggest that online resistance training was effective in improving MS and reducing the body composition and circumference.

According to the development needs of marine seismic station networking, it is necessary to develop a marine seismometer with a networking function to realize quasi-real-time and large-scale long-term observation of undersea seismic signals. This can lay a solid foundation for marine seismic research and research on earth tectonics, activities, and processes. Based on the advantages and disadvantages of the existing observation equipment, this study proposed to develop a new type of the Autonomous Glide Marine Seismometer(AGMS) that can be applied to the global sea area, focusing on the design and study of the main structure of the carrier of the AGMS. The ultimate strength of the ellipsoidal pressure-resistant spherical shell is investigated by using the finite element analysis method. A reasonable finite element analysis model is proposed through comparing the finite element parameter results with the theoretical formulas and relevant specifications. Finally, the design process and strength checking of the pressure-resistant shell of the AGMS are established. These relevant results can also provide a reference for the design of other deep-sea pressure-resistant chambers.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

Background: Radiotherapy is an important part of the medical therapy concept treating tumors in the head and neck region; however, the impact on the field of dentistry could be im-mense. The objective of this study was to evaluate the microtensile bond strength (µTBS) of uni-versal adhesives and to compare the results of different application modes (etch-and-rinse and self-etch) on irradiated and sound human dentin. Methods: Dentin specimen of 180 extracted human wisdom teeth were divided in two superordinate groups. Ninety teeth received either no irradiation (control group) or the high-level therapeutic dose of 60 Gy (test group) applied frac-tionally (2 Gy/day, 5 days/week, 6 weeks). Samples from each group were randomly divided in-to six subgroups assigned to three established universal adhesives (Futurabond® U, VOCO; AdheSE® Universal, Ivoclar Vivadent; Xeno® Select, Dentsply) in both conceivable application modes: etch-and-rinse and self-etch (n = 15). Bond strength was assessed with a universal testing machine immediately after application and light curing of the adhesive materials. Statistical analysis was performed using two-way ANOVA (p<0.01) and Tukey's test (p<0.05). Results: The effect of dentin irradiation and application mode for the adhesive restoration was found to be significant (p<0.01, ANOVA). In all groups, a decrease of µTBS could be observed when used on irradiated dentin. However, no significant influence of high level radiation on the bond strength of Futurabond® U and AdheSE® Universal in both modes could be evaluated (p>0.05, Tukey´s test). Solely in the case of the adhesive system Xeno® Select, significantly reduced bond strength could be determined in self-etch mode after irradiation (group 60 Xse) compared to the control group (0 Xse) (p<0.05, Tukey´s test). Conclusions: Within the limitations of an in vitro study, some effects of high-level tumor irradiation on the bond strength of universal adhesives can be detected. However, these effects were strongly depending on the used material and application mode.

Generally, mineral fillers are added to thermoplastic polymers to reduce cost and improve performance. However, properly selected mineral fillers can also improve thermal conductivity and deformation behavior, shrinkage, impact strength, dimensional stability, and molding cycle time in thermoset polymers. This study focused on the preparation and microscopic and spectroscopic characterization of various hybrid composites using pumice as primary filler and gypsum, kaolin and hollow glass sphere as secondary fillers, as well as examining some of their mechanical properties and thermal conductivities. For this, first of all, surface modification of the clay was carried out by intercalation method from solution using raw Montmorillonite, cationic surfactant and long chain hydrocarbon material, and then organo-clay melamine formaldehyde nanocomposite was prepared by in situ synthesis using organo clay and melamine formaldehyde pre-polymer. Finally, non-ionic surfactant, foaming agent and glycerin were added to the prepared nano-composite at approximately 90°C, mixed mechanically and then pumice was added. The processes at this stage were repeated while preparing hybrid composites with pumice and other mineral additives. For curing and molding, the composite was first subjected to microwave irradiation for 5 minutes followed by thermal treatment at 140°C for 60 min. Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD) spectra and Scanning electron microscope (SEM) and High resolution transmission electron microscope (HRTEM) images were taken for morphological and textural characterization for raw clay (MMT), organo clay (OMMT) and pure polymer with prepared hybrid composites. In addition, some mechanical properties such as bending strength, elasticity modulus and screw holding resistance, as well as thermal conductivity coefficients of the hybrid composites were determined according to the relevant standards and the obtained results were evaluated. Spectroscopic and microscopic analyzes have shown that effective adhesion interactions occur between polymer-clay nanocomposite particles and filler grains, thus resulting in textural arrangements with different properties. Mechanical and thermal conductivity test results showed that melamine formaldehyde-organo-clay nano composite foam and hybrid composite containing hollow glass sphere are highly qualified materials in terms of thermal insulation and mechanical strength.

The functional capacity of the cervical spine plays a central role in healthy living. This study evaluated and created a comprehensive strength, range of motion (ROM), and musculoskeletal pain profile of the cervical spine in young adults. 60 physically active individuals (30 males/30 females; 19-24 year-old) participated in the study. Cervical ROM (forward flexion, extension, lateral flexion, and rotation), maximal isometric strength (forward flexion, extension, lateral flexion), and musculoskeletal pains were assessed using an electronic goniometer, a handheld dynamometer, and the Nordic questionnaire, respectively. Data analysis revealed that: a) fe-males had higher ROM values, during extension and lateral flexion, than males (p<0.05), b) males had higher absolute strength values than females in all movement directions, higher rela-tive strength values/body mass (at forward flexion) and flexion/extension ratio values (p<0.05), c) ROM and strength values were not significantly different between right-left sides (p>0.05), d) a great proportion (43.3%) of the participants had cervical pains (no sex-related differences) and e) cervical strength showed significant small negative correlation with pains (p<0.05; r=-0.225 to -0.345). The reference values created may be used by health and fitness professionals to exten-sively evaluate the cervical spine and to design specific exercise programs for injury prevention and rehabilitation.

Paving blocks are concrete pieces placed in exposed places to the weather, which are sub-jected to loads and wear. Hence, quality control in the manufacture of paving blocks is es-sential to guarantee the properties and durability of the product in construction projects. In Ecuador, the requirements are described in the Ecuadorian technical standard "NTE INEN 3040", and tensile splitting strength is a fundamental requirement to guarantee product quality. It is analyzed using quality control measurements such as dimensions, the weight of the fresh paving block in the vibro-compacted process, and the percentage of water absorption in order to know how the variables influence and manage to predict the tensile splitting strength to avoid product non-conformity in advance, having a timely and better control of the manufacturing process. The data was obtained from a company that can produce 30 000 units per day of rectangular paving blocks with 6 cm thickness. Mul-tivariate models such as multiple linear regression, regression trees, random forests and neural networks are performed to predict the tensile splitting strength variable through two groups of predictors; the first group is the thickness mm, width mm, length mm, mass of fresh paving block g and percentage of water absorption %. The second group of pre-dictor variables is the density of the fresh paving block kg/m3 and the percentage of water absorption %. It is concluded that the multiple linear regression method performs better in predicting the first group of predictor variables with a mean square error (MSE) of 0.110086, followed by the neural network without hidden layers resulting in an MSE of 0.112198. The best method for the second set of predictors was the neural network with-out hidden layers with a mean square error ( MSE ) of 0.112402, closely followed by the multiple linear regression model with an MSE of 0.115044.

Printed oral splints are a therapeutic alternative in the treatment of functional disorders. Their mechanical properties are crucial to their clinical success and their performance can vary depending on cleaning, post-polymerization, or build orientation. This in vitro study aimed to compare the biaxial flexural strength of the chosen materials depending on the aforementioned parameters. 720 discs (n = 15 per group, 16 mm x 2 mm) were printed from splint materials. Printing was performed under 90°, 45°, or 0° orientation to the building platform with supporting structures. Specimens were either automatically or manually cleaned with isopropanol. Post-polymerization was performed with LED- or Xenon-light. Biaxial flexural strength (BFS) was determined with a piston-on-3-ball test after 24 hours or 60 days water storage (37°C). Test specimens were preloaded with 0.5 N and the load was applied by a piston of 1.6 mm in diameter at 1 mm/min crosshead speed. Statistics were performed by using descriptive statistics, ANOVA, and Levene-tests. Mean BFS after 24 hours of storage varied between 79 MPa and 157 MPa. After 60 hours the BFS significantly decreased and revealed values ranging from 72-127 MPa (mean24 113 MPa, mean60 97 MPa; p&lt;0.001). No significant differences could be determined between the materials (p=0.103) or between the different cleaning procedures (p=0.321). Post-polymerization yielded higher means with LED- (P1: 115 MPa) than with Xenon-light (P2: 95 MPa; p&lt;0.001). Regarding position, the mean values ranged from 101 MPa for 0°, 102 MPa for 45°, and 115 MPa for 90°, which was significantly different (p&lt;0.001). Build orientation of 90° and post-polymerization with LED-light provided significantly higher biaxial flexural strength and should be used to guarantee optimal strength of splint materials. Aging decreased the biaxial flexural strength of the tested specimens.

This study assessed the potential of back extensor strength as an alternative marker of frailty. A total of 560 farmers were included. Computed tomography scans measured fat and muscle mass volumes at the mid-L4 vertebral level. Back extensor strength was measured in a seated posture. Multivariate linear regression analyzed the associations between back extensor strength and trunk muscle/fat compositions. The participants were divided into two groups based on back extensor strength. Propensity score matching, multivariate logistic regression, and Extreme Gradient Boosting (XGBoost) were employed to evaluate the relationship between Fried's frailty criteria and back extensor strength. Back extensor strength exhibited positive associations with abdominal muscle volume (r = 1.12) as well as back muscle volume (r = 0.89) (p < 0.05). Lower back extensor strength was linked to more frail status, such as reduced grip strength, walking speed, and fre-quent self-reported exhaustion. Multivariate logistic regression indicated a significant association between lower back extensor strength and higher Fried frailty score (OR, 0.990; p<0.05). XGBoost analysis identified back extensor strength as the most important predictor (gain = 0.502) for frailty, surpassing the significance of age (gain = 0.325). These findings suggested the potential of back extensor strength as an alternative frailty marker.

Inertial training is one of the most popular training methodologies in the last years and one of the objects of study in recent literature, however more studies are necessary to know its usefulness in young athletes. The aim of the current systematic review is to evaluate the current literature surrounding the chronic effect of inertial training on physical capacities of team sports through functional test. This systematic review was conducted in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses Protocols (PRISMA). The results revealed the effectiveness of these tools for improving abilities such jumps, sprints, change of directions and power measure. In conclusion, inertial training can be an adequate stimulus for the better performance in young athletes on team sports.

This paper presents the use of Graph Neural Networks (GNNs) to predict the tensile strength of Fused Deposition Modeling (FDM) specimens. In the present work, there are four main input parameters i.e. Infill percentage, Layer height, Print speed and Extrusion temperature while the Tensile Strength is an output parameter were considered. This study includes use of central composite design based response surface methodology to finalize the experimental layout. 3D printed specimen were manufactured as per the ASTM E8 standard on FDM printer using Polylactic Acid (PLA) as filament. Micro-tensile test were performed on the printed specimen as per ASTM E8 standard. The GNN algorithm was trained on a dataset of FDM specimens, achieving a mean squared error (MSE) of 2.47, mean absolute error (MAE) of 1.14, and R-squared value of 0.78. An adjacency matrix, which shows the connections between nodes in a graph. The obtained plot for nodes and weights in a GNN provide valuable information about the model and its performance. The results show the potential of using GNNs in predicting the mechanical properties of additively manufactured specimens and provide a promising direction for further research in this field.

Flue gas desulfurization gypsum (FGD gypsum) is obtained from the desulphurization of combustion gases in fossil fuel power plants. FGD gypsum can be used to produce anhydrite binder. The effect of three independent variables such as the calcination temperature of FGD gypsum (500-800 oC), the hydration time (3-28 days) and the amount of activator (0-2 %) on the compressive strength of anhydrite binder were studied. K2SO4 and Na2SO4 were used as activators. The compressive strength of anhydrite binder was evaluated using a full factorial design. The multiple linear regression models were developed to correlate the significant variables to the compressive strength of anhydrite binder. The experimental results and statistical analysis showed that the hydration time had the biggest impact on the compressive strength of anhydrite binder using K2SO4 and Na2SO4. K2SO4 made a greater influence on the compressive strength than Na2SO4. The results of modeling indicated that the individual variables had a larger effect on the compressive strength of anhydrite binder than their interaction. The mean absolute percentage error between experimental and calculated values of compressive strength was less than 10 %.

Natural Fibre Reinforced Composites (NFRCs) represent a significant category of materials that has the capacity to contribute to the worldwide objectives of sustainability and environmental preservation. To maximise the potential of composite materials, it is essential to establish their high quality and cost-effective manufacture. While the basic production procedures for producing items based on NFRCs have reached a high level of development, more research efforts are needed to advance their secondary manufacturing processes, namely in the areas of machining and joining. The primary factor leading to the rejection of composite goods with holes is the damage generated during the drilling process. The present experimental study aims to examine the effectiveness of hole production during the moulding phase. A comparative analysis has been conducted to assess the mechanical characteristics of moulded and drilled holes in jute fibre reinforced epoxy composite. It was observed that the moulded holes exhibit superior performance compared to the drilled holes for jute/epoxy materials. Additionally, the load extension curves indicate that the moulded holes experience greater extension in comparison to the drilled holes.

Breast cancer is the most common malignant disease in women. Preclinical studies have confirmed that the local anesthetic levobupivacaine has a cytotoxic effect on breast cancer cells. We examined whether postoperative wound infiltration with levobupivacaine influences survival in 120 patients who were operated on for breast cancer and underwent quadrantectomy or mastectomy with axillary lymph node dissection. Groups with continuous levobupivacaine wound infiltration, bolus wound infiltration, and diclofenac analgesia were compared. Long-term outcomes examined were quality of life, shoulder disability, and hand grip strength (HGS) after one year, and survival after 5 and 10 years. Groups that had infiltration analgesia had better shoulder function compared to diclofenac after one year. Levobupivacaine PCA group had the best preserved HGS after 1 year (P=0.022). The most significant predictor of the 5-year outcome was HGS (P=0.03). Although the best survival after 5 and 10 years was registered in the bolus levobupivacaine group, statistical significance was not reached (P=0.36). The extent of the disease at the time of surgery is the most important predictor of long-term survival. A larger prospective clinical study could better confirm the effect of levobupivacaine wound infiltration on outcomes after breast cancer surgery observed in this pilot study. Trial number NCT05829707

Polyimide (PI) films are widely used in electronic devices owing to their excellent mechanical and electrical properties and high thermal and chemical stabilities. In particular, PI films play an important role in flexible printed circuit boards (FPCBs). However, one challenge currently faced with their use is that the adhesives used in FPCBs cause a high dielectric loss in high-frequency applications. Therefore, it is envisioned that PI films with a low dielectric loss and Cu films can be used to prepare two-layer flexible copper clad laminates (FCCLs) without any adhesive. However, the preparation of ultra-thin FCCLs with no adhesives is difficult owing to the low peel strength between the PI films and Cu films. To address this technical challenge, an FCCL with no adhesive was prepared by high-power helicon wave plasma (HWP) treatment. The surface roughness of the PI film and the peel strength between the PI film and Cu film were measured. The experimental results showed that the surface roughness of the PI film increased by 40-65% and the PI film demonstrated improved adhesion (the peel strength was &gt;8.0 N/cm) with the Cu film following plasma treatment and Cu plating.

This study investigates the long-term impact of soil tillage systems and crop residue incorporation on agrophysical properties. A long-term field experiment has been conducted since 1999 at the Ex-perimental Station of Vytautas Magnus University Agriculture Academy. According to the latest edition of the International Soil Classification System, the soil in the experimental field was classified as Planosol, with a silty medium loam texture at a depth of 0–20 cm and a silty light loam at a depth of 20–40 cm. This investigation aimed to assess the long-term impact of reduced tillage systems, straw, and green manure combinations on soil physical properties, including soil shear strength, and soil aggregate stability. Studies were carried out on winter wheat crops in 2014, 2017, and 2023. The treatments were arranged using a split-plot design. In a two-factor field experiment, one part of the experimental field had straw removed, while the other part had the entire straw yield chopped and spread at harvest (Factor A). The subplot factor (Factor B) included three different tillage sys-tems: conventional deep ploughing, cover cropping for green manure with no-till, and no-tillage. Soil samples were analysed in the Laboratory of Agrobiology at Vytautas Magnus University Ag-riculture Academy. The findings indicate that long-term application of reduced tillage significantly increases soil shear strength. Shallower tillage depths lead to higher soil shear strength, while the effect of spreading plant residues is relatively lower. Long-term tillage of different intensities, spreading plant residues, and catch crop cultivation for green manure did not significantly affect soil structure. However, soil structural stability was found to be highly dependent on soil tillage. Cover cropping for green manure with no-till and no-tillage positively affected soil aggregate sta-bility in the upper (0–10 cm) and 10–25 cm layers.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

Artificial intelligence is increasingly used in various branches of engineering. In this article, artificial neural networks are used to predict the crush resistance of corrugated packaging. Among the analysed packages were boxes with ventilation openings, packages with perforations, and typical flap boxes, which makes the proposed estimation method very universal. Typical shallow feedforward networks were used, which are perfect for regression problems, mainly when the set of input and output parameters is small, so no complicated architecture or advanced learning techniques are required. The input parameters of the neural networks are selected so as to take into account not only the material used for the production of the packaging, but also the dimensions of the box and the impact of ventilation holes and perforations on the load capacity of individual walls of the packaging. In order to maximize the effectiveness of neural network training process, the group of input parameters was changed so as to eliminate those to which the sensitivity of the model was the lowest. This allowed the selection of the optimal configuration of training pairs for which the estimation error was on the acceptable level. Finally, models of neural networks were selected, for which the training and testing error did not exceed 10%. The demonstrated effectiveness allows to conclude that the proposed set of universal input parameters is suitable for efficient training of a single neural network model capable of predicting the compressive strength of various types of corrugated packaging.

It is estimated that about 50% of geriatric rehabilitation patients suffer from sarcopenia. Thereby, malnutrition is frequently associated with sarcopenia and dietary intake is the main modifiable risk factor. During hospitalization, older adults are recommended to consume more dietary protein than the current recommended dietary allowance of 0.8 g/kg body weight per day to optimize the recovery of muscular strength and physical function. This prospective study examined the effect of a short-term protein supplementation with protein-enriched foods and drinks on hand-grip strength, nutritional status and physical function in older patients at risk of malnutrition during a three week inpatient orthopedic rehabilitation stay. The Mini Nutritional Assessment (MNA) was used to assess malnutrition. Patients with a MNA score ≤ 23.5 points were randomly assigned to an intervention group (goal: to consume 1.2–1.5 g protein/kg body weight per day) or a control group (standard care). Both groups carried out the same rehabilitation program. Physical recovery parameters were determined at admission and discharge. There was a trend for participants in the intervention group to consume more protein than the control group (P = 0.058): 95.3 (SD 13.2) g/day as compared to 77.2 (SD 24.2) g/day, which corresponds to a mean protein intake of 1.6 (SD 0.3) g/kg/day vs. 1.3 (SD 0.5) g/kg/day. Dietary protein supplementation increased body weight by an average of 0.9 (SD 1.1) kg and fat mass by an average of 0.9 (SD 1.2) kg as compared with baseline (P = 0.039 and P = 0.050, respectively). There was no significant change in hand-grip strength, body composition and physical function. In conclusion, a short-term intervention with protein-enriched foods and drinks enabled older patients at risk of malnutrition to increase their protein intake to levels that are higher than their required intake. In these older individuals with appropriate protein intake, dietary protein supplementation did not result in a greater improvement in physical recovery outcomes during short-term inpatient rehabilitation. The intervention improved dietary protein intake, but further research (e.g., a full-scale randomized controlled trial with sufficient power) is required to determine the effects on physical function outcomes.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

In order to effectively utilize red mud, an aluminum industrial waste, the stabilized soil material was developed using nano-SiO2 synergistically modified red mud, and the strength characteristics of the stabilized soil were analyzed to clarify the feasibility of such stabilized soil serves as a road base material. Through different combination schemes, the effects of different nano-SiO2 and cement contents on the strength of the stabilized materials were explored. The test results show that: in the synergistic modification of nano-SiO2 and cement, nano-SiO2 can significantly improve the early unconfined compressive strength of red mud-based stabilized soil; in the synergistic modification of nano-SiO2, gypsum and cement, the 7-d unconfined compressive strength of red mud-based stabilized soil is greater than 2 MPa, which meets the strength requirements of road base materials and shows the superiority of synergism. The nominal stress-strain curves are divided into five stages: compressed and compacted stage, elastic deformation stage, plastic deformation stage, damage deformation stage and residual deformation stage. The macroscopic compressive damage pattern of the specimens shows that the modified red mud-based stabilized soil mostly exhibits brittle damage.

There are no studies that have investigated the characteristics of car use across THA patients, including those who do not drive. This study aimed to evaluate, in THA patients, (1) postoperative car usage, (2) comfort while entering and exiting a car, and (3) whether lower limb muscle strength affects action comfort. One hundred seventy-two post-THA patients completed the questionnaire in 2020, along with assessments of hip abductor and knee extensor muscle strength before surgery and at discharge. Patients whose overall comfort level was judged as “comfortable” were defined as the “comfort” group; others were placed in the “discomfort” group. Of the 172 patients, 161 reported car usage at a mean of 5.6 years after THA. Of these, 114 and 47 patients were placed in the "comfort" and "discomfort" groups, respectively. Patients in the "discomfort" group were three times more likely to experience discomfort using the contralateral side door than the surgical side door, and about twice as many patients experienced discomfort when entering as when exiting. Lower preoperative contralateral hip abductor muscle strength was the only independent predictor for discomfort. The take-home messages were that prevention of contralateral-side weakness may improve comfort during the action after THA.

On the analyzed section of 2.4 km of the national road No. 50 of the Młodzieszyn bypass, it was carried out by a consortium of OAT and SAT companies in the period April-September 2019, under constant traffic in the field of repairing the concrete pavement by replacing slabs, levelling them and sealing expansion joints, roughening and roadside reinforcements.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

This study investigates the influence of the porous structure, on the density and the mechanical behaviour of new foam concretes incorporating hemp shives. A total of eight batches of foam concretes were manufactured and tested, made with a protein-based foam agent, containing cement, ground granulated blast furnace slag and Metakaolin as binder and hemp shives as natural aggregate. The effect of several parameters is studied, elaboration method (direct and preformed), amount of pozzolanic additions (0% and 30%) and incorporation of hemp shives (5 and 15 vol%) on the resulting physical properties, microstructure, porous structure and mechanical behaviour of the concretes. Hemp shives incorporation results in increased concrete porosity and air bubble radius, decreased uniformity and mechanical strength, and lower cohesion with the cement matrix compared to standard concretes.

This publication describes the influence of residue monomers in synthesized pressure-sensitive adhesives based on acrylics on main performance such as tack, peel adhesion, shear strength and shrinkage in form of transfer tapes used for joining wooden elements in furniture industry. The discussed carrier-free adhesive tapes are synthesized by photo-crosslinking and photopolymerization with UV radiation of photoreactive prepolymers sandwiched between two adhesive siliconized polyester films. The simultaneous crosslinking and polymerization process under UV lamps carried out under UV lamps placed simultaneously above and below the crosslinked photoreactive polymer layer leads to the production of a carrier-free adhesive film. In this test series it were investigated to what how the intensity of UV radiation and the time of its exposure affect the viscosity of photoreactive compositions, and then the content of unreacted monomers in them and, subsequently, the method of their crosslinking and polymerization, and the concentration of the photoreactive crosslinking compound leading to the obtaining of transfer adhesive tapes, and thus on their tray, peel adhesion, shear strength and shrinkage on the surface of the wood.

Polymer-based composites represent a separate class of materials in demand by the industry. In comparison with other polymers, UHMWPE is characterized by exceptionally high wear and impact resistance. In this work, compacts were produced from UHMWPE GUR 4120 powder with the addition of Nanoscale Detonation Carbon (NDC) and Single-Walled Carbon Nanotubes (SWCNTs) on a hydro-pneumatic impact device by the Cyclic Impact Compaction (CIC) technique. The obtained samples were subjected to wear resistance test, their hardness and tensile strength were measured. Studies have shown that the addition of NDС and SWCNTs in UHMWPE leads to an increase in hardness by 6.4 and 19.6%, to a decrease in wear by 11.5 and 38.5% and a decrease in the coefficient of friction by 10 and 20%, respectively. However, the tensile strength of UHMWPE decreases by 11.7 and 40.4% and elongation decreases by 11.9 and 30.1% with the addition of NDС and SWCNTs, respectively.

Magnesium matrix composites have attracted significant attention due to their lightweight nature and impressive mechanical properties. However, the fabrication process for these alloy compo-sites is often time-consuming, expensive, and labor-intensive. To overcome these challenges, this study employed machine learning (ML) techniques to predict the mechanical properties of magnesium matrix composites. Regression models were utilized to forecast the yield strength of magnesium alloy composites reinforced with various materials. The study incorporated previous research on matrix type, reinforcement type, heat treatment, and mechanical working. The re-gression models employed in this study included decision tree regression, random forest re-gression, extra tree regression, and XGBoost regression. Model performance was assessed using metrics such as RMSE and R2. The XGBoost Regression model out-performed others, exhibiting an R2 value of 0.94 and the lowest error rate. Feature importance analysis indicated that the rein-forcement particle form had the greatest influence on the mechanical properties. The study iden-tified the optimized parameters for achieving the highest yield strength, which was 186.99 MPa. Overall, this study successfully demonstrates the effectiveness of ML as a valuable tool for opti-mizing the production parameters of magnesium matrix composites.

Aging is associated with muscle atrophy and fatty infiltration of skeletal muscle. The multifidus muscle stabilizes the lumbar spine and undergoes adipose accumulation with age, leading to functional decline in the elderly. Therefore, quantitative assessment of the multifidus muscle can be beneficial for the elderly when formulating treatment strategies and reducing future complications. Fifty-seven patients (mean age, 73.89 ± 6.09; 23 male patients) who underwent lumbar Magnetic resonance imaging (MRI) were prospectively recruited. The cross-sectional area (CSA) of the multifidus from the L2-S1 level and the CSA of the L4-5 level psoas muscle were measured. The functional CSA (fCSA) of the multifidus muscle was measured by excluding the fat infiltration area from the multifidus CSA. The CSA to fCSA ratio was obtained by multiplying 100 by the value obtained by dividing CSA by the fCSA. Pfrrmann classification was used to evaluate the degree of disc degeneration. The functional disability measurements were the Short Physical Performance Battery (SPPB), Berg Balance Scale (BBS), grip strength, and functional reach test (FRT). Pearson's correlation analysis was used to examine the relationship between the functional disability measurements and the multifidus muscle. The CSA to fCSA ratio value was relatively constant at each spine level and showed a significant correlation with the SPPB, grip strength, FRT, and psoas index (p&lt;0.05). However, degree of disc and multifidus muscle degeneration were not statistically significant. So, age-related changes play a significant role in developing back muscle fatty infiltration than disc dgeneration. Moreover, Grip strength showed a stronger relationship with the quality of the multifidus muscle than other functional disability measurements.

Natural rocks are highly heterogeneous due to various geological processes that constantly alter their properties. The accumulation, deposition, and cementation of mineral and organic particles continuously modify the spatial characteristics of rock properties. Property variability or anisotropy is commonly observed in most rock types and influences strength, transport, and thermal conductivity behavior. This unpredictability presents a significant challenge for laboratory testing. Binder-jet additive manufacturing (3D printing) has emerged as a valuable technology for characterizing rock properties in geoscience and engineering. This study proposes a methodology to evaluate the variability and repeatability of mechanical properties of 3D-printed sandstones during binder-jet additive manufacturing. The mechanical properties were analyzed statistically for samples located in various parts of the 3D printer build volume. The results showed that the 3D-printed sandstones exhibited significant variations in their strength and stiffness properties when measured from samples produced within the same build volume during binder-jet additive manufacturing. The Uniaxial Compressive Strength (UCS) varied from 23 to 38 MPa, with an average value of 29 MPa. The Young's modulus, on the other hand, ranged from 1.5 to 4.05 GPa, with an average value of 2.33 GPa. The variability of the mechanical properties, quantified by the standard deviation, decreased when the entire population of 3D-printed sandstones was divided into smaller samples situated at different elevations of the build platform.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

In the article, we are trying to find a general law that describes the physical properties of a complex compound through the same physical properties of compound elements. For metal alloys operated under extreme conditions - neutron and proton irradiations and thermal heating, the mechanical properties of these alloys and their elements have been studied. It turned out that the ultimate tensile strength of tantalum alloys used in the design of space reactors can be expressed in terms of the weighted sum of the ultimate tensile strengths of its elements in the range of neutron doses: (0 - 0.96) displacement per atom (dpa) for Ta–10W alloy and (1.4 - 1.7) dpa for T–111 alloy with a neutron energy of more than 0.1 MeV. For tungsten binary alloys used in the design of fusion reactors, the Vickers hardness can also be expressed in terms of the weighted sum of the Vickers hardnesses of the alloy elements in the range of proton irradiation doses: (0 - 0.05) dpa for W-1%Re alloy, (0.05 - 0.2) dpa for W-3%Re alloy and (0.05 - 1) dpa for W-1%Ta with a proton energy of 1 MeV.

Adiposity is associated with adverse health conditions such as obesity, cardiovascular disease and type 2 diabetes. The combination of resistance exercise and creatine supplementation has been shown to decrease body fat % in adults ≥ 50 years of age. However, the effects in adults < 50 years of age is unknown. To address this limitation, we systematically reviewed the literature and performed several meta-analyses comparing studies that included resistance exercise and creatine supplementation to resistance exercise and placebo. Twelve studies were included involving 266 participants. Adults (< 50 years of age) that supplemented with creatine and performed resistance exercise experienced a significant reduction in body fat % (-1.19%, p=0.006) and a non-significant reduction in absolute fat mass (-0.09 kg, p=0.88). Collectively, the combination of resistance exercise and creatine supplementation produces a very small reduction in body fat % in adults < 50 years of age.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

Background: Evidences on the effects of chemotherapy treatment cycles on measures of muscle, mental state, social and cognitive performance are scarce. Objective: To analyze the effects of chemotherapy cycles on muscle strength and activation, functional capacity, quality of life, fatigue and anxiety of women with breast cancer. Methods: Twenty-two women divided into a treatment group (n = 10; 46.6 ± 9.6 years) and control group (n = 12; 51.6 ± 7.0 years) participated in the study. Analysis of muscle performance, quality of life, fatigue and anxiety after the 2nd and 4th cycle of chemotherapy with anthracyclines and cyclophosphamide were performed in women with breast cancer (TRA) and compared to healthy women (CTR). Two-way ANOVA was used to compare the variance of the means and the significance level was set as p≤0.05. Results: Differences were found in the muscular activation of the vastus medialis between the groups at post time (p = 0.038), as well as in the sit and stand test in the baseline (p<0.001) and post moment (p<0.001). Functional capacity performance was different between baseline (p<0.001) and post-time (p<0.001) groups. Additionally, the TRA group worsened the quality of life in the domains of functional capacity (p<0.001) and limitation of physical aspects (p=0.002), besides presenting negative changes in fatigue. Conclusion: Anthracycline and cyclophosphamide chemotherapy cycles reduce muscular performance and affect biopsychosocial variables in women with breast cancer.

Water damage is one of the main causes of roads’ deterioration throughout their service life. This effect harms the adhesion and cohesion parameters of the asphalt mix, which leads to a decrease in the structural and functional characteristics of the road surface. This research focuses on studying the water susceptibility of hot mix asphalt mixtures using three different procedures: (1) UNE-EN 12697-12, (2) ASTM D4867, and (3) AASHTO T-283. The tests are carried out on reference mixtures and mixtures modified with polyethylene terephthalate (PET) particles as an additive. The results indicate that the incorporation of 6% PET allows the limits established by the UNE-EN 12697-12 standards to be exceeded, reaching 86% of the tensile strength ratio (TSR). However, for the ASTM D4867 and AASHTO T-283 standards, the results obtained concerning the water susceptibility of the bituminous mixtures were not as satisfactory because the established minimum limits were not reached (&lt; 75%), which indicates that the procedure applied in a test can significantly modify the results of a later application.

Background: Physical and mental health of corporate employees is equally important, especially in international salespeople in the in vitro diagnostic (IVD) medical device industry. The rapid growth of the IVD market is driven by the increasing prevalence of chronic and infectious diseases. This study aims to identify the association of socio-demographic, occupational, organizational, and psychosocial factors with mental health outcomes for depression, anxiety, and somatic symptoms in Chinese IVD international salespeople. Methods: The study was a cross-sectional survey of ISs in IVD companies officially registered in China. An online survey was designed to collect data through email contact with IVD companies and social media between August 2022 and March 2023. Measured factors included effort-reward imbalance (ERI), health-promoting leadership (HPL), health climate (HC), inner strength (IS), and perceived social support (PSS). Mental health outcomes assessed using the Core Symptom Index (CSI) were depression, anxiety, and somatic symptoms. Results: A total of 244 salespeople responded to the survey. CSI scores indicated that 18.4% (n = 45) and 10.2% (n = 25) of the respondents had symptoms of major depression and anxiety, respectively. ERI was positively correlated, while the IS and PSS were negatively correlated with major depression, anxiety, and somatic symptoms (p < .01). Health climate was negatively correlated with major depression (p < .05). Education background was associated with somatic symptoms (p < .05). ERI, IS, and gender were significant predictors of major depression, anxiety, and somatic symptoms (p < .05). Conclusion: The prevalence of depression and anxiety in China’s IVD international salespeople was considered low compared with prevalence in Chinese populations during COVID-19, but higher than those before the pandemic. Effort–reward imbalance, inner strength, and gender were significant factors in major depression, anxiety, and somatic symptoms among IVD international salespeople.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Abstract: To overcome the environmental impact of cement production in cocnrete , the construction industry is adopting eco-friendly approaches, such as incorporating alternative and recycled materials, minimizing carbon emissions in concrete production. One such material that has gained prominence is Ground Granulated Blast Furnace Slag (GGBFS),. This study focuses on investigating the compressive strength of concrete at 28 days of age by examining the influences of several factors, such as temperature, water-to-binder ratio (w/b), GGBFS-to-binder ratio (GGBFS/b), fine aggregate, coarse aggregate, and superplasticizer. A statistical modeling approach was employed to comprehensively analyze these parameters and assess their impact on the compressive strength. To accomplish this, the study collected and analyzed data from the literature, resulting in a dataset of 210 observations. The dataset was divided into training and testing groups, and statistical analyses were performed to assess the relationships between the input parameters and compressive strength. The correlation analysis revealed insignificant relationships between the input parameters and compressive strength, indicating that multiple factors affect the strength. Different models, such as linear regression, nonlinear regression, quadratic, full quadratic models, and artificial neural networks (ANN) were employed to predict the compressive strength. The findings of this study contribute to a better understanding of the factors that influence the compressive strength of concrete containing GGBFS. The results underscore the importance of considering multiple parameters to predict strength accurately.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

Player’s performance in an intense sport such as basketball is known to be related to attributes like speed, agility, and power. This study presents a comparative analysis of associations between anthropometric assessment and physical performance in different age-group elite youth basketball players, while simultaneously identifying the predictors for speed and agility in these players. U14 (n=44), U15 (n=45) and U16 (n=51) players were tested for anthropometry, lower body power, speed, and agility. U16 players were found to be taller, heavier, more muscular than U14 and U15 players. Also, the U16 group showed better performance in all performance tests. Age had a significant positive correlation with countermovement (CMJ) and drop jump (DJ) performance in U14 players, and a significant negative correlation with 10m and 20m sprint times in U15 group. CMJ and DJ emerged as the most significant predictors for sprint and agility variables, respectively. Body fat percentage was found to be a significant predictor for the speed and agility tests in all age groups, but a negative lower-body power predictor. Therefore, besides all sport-specific and fitness tests, it is essential to place emphasis on the percentage of body fat when designing players’ individualized training programs, and during team selection.

Chitosan's favourable characteristics, such as biocompatibility, biodegradability, and bioactivity, have made it a popular biomaterial and the subject of numerous studies over the last years. This study investigates the enhancement of mechanical properties of chitosan fibres through wet impregnation using tripolyphosphate (TPP) as cross-linker. A 1% w/v solution of TPP was prepared and five separate chitosan fibre specimens were immersed individually in TPP solution for varying times (1, 2, 4, 6, and 8 hours). The specimens were then characterized using FTIR, SEM, and dynamometry to evaluate their physical, chemical, and mechanical properties. The FTIR results indicated successful interaction between the protonated amine groups of chitosan and TPP ions, with the crosslinking reaction reaching completion after 2 hours of immersion. SEM images showed that the surface of the fibres became rougher after the crosslinking reaction, suggesting the formation of new chemical bonds. Mechanical testing revealed a significant improvement in tensile strength for the treated samples compared to untreated ones, indicating successful strengthening through crosslinking. The fibres demonstrate significant potential for use in wound healing dressings.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

Polymeric wet-strength agents are important additives used in the paper industry to improve the mechanical properties of paper products, especially when they come in contact with water. These agents play a crucial role in enhancing the durability, strength, and dimensional stability of paper products. The aim of this review is to provide an overview of the different types of wet-strength agents available and their mechanisms of action. We will also discuss the challenges associated with the use of wet-strength agents and the recent advances in the development of more sustainable and environmentally friendly agents. As the demand for more sustainable and durable paper products continues to grow, the use of wet strength agents is expected to increase in the coming years.

This paper aims to investigate the feasibility of strengthening the web opening in the shear zone of RC beams by using iron-based shape memory alloy (Fe-SMA) bars. To conduct this study, numerical analysis with ABAQUS software was employed. The research was divided into six groups of beams with web openings of different lengths (150, 300, and 450 mm), prestressing levels (0%, 30% and 60%), and reinforcement diameters (14, 18, and 22 mm) of Fe-SMA bars. The results show that the presence of web openings can cause a significant reduction in the cracking and ultimate loads of the beams, with reductions ranging from 11 to 50% and 36 to 48%, respectively. However, by adding pre-stressed Fe-SMA bars around small web openings (100×150 mm), the shear capacity of the beam is restored, and the beam exhibits behavior similar to solid beams. Additionally, activating the Fe-SMA bars by 30 and 60% resulted in almost similar cracking loads but improved load-carrying capacity of the beam with small openings by 12% and 9%, respectively, compared to the solid beam. The technique proposed for enhancing shear strength is most effective for beams with small (100×150 mm) and medium (100×300 mm) web openings as it can restore both the beam’s shear strength and stiffness. However, for beams with larger web openings (100×450 mm), the use of activated Fe-SMA beams can recover almost 90% of the solid beam's shear capacity. Furthermore, reinforcing small openings with Fe-SMA bars of different diameters enhances beam shear capacity and stiffness, while for larger openings, higher Fe-SMA reinforcement ratios could potentially restore the beam's full strength and stiffness. This study emphasizes the importance of strengthening web openings in RC beams, particularly in shear zones, and provides significant insights into how to strengthen beams with web openings, thereby contributing to developing safer structures. However, further laboratory experiments are recommended to validate, complement and extend the findings of this numerical study.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

Samples of mortar mixtures were prepared substituting the cement Portland (CPC-30R) by 0 (standard), 10 and 15% of fly ash and the structural evolution and compressive strength at 3, 7, 14 and 28 days were determined. The results for standard mortar samples showed the mineralogi-cal species portlandite, calcite, ettringite, iron oxide, silicon oxide and sillimanite. Magnetite was identified in the mixtures of mortars with portland cement substitution by 10% and 15% fly ash. The peaks corresponding to the portlandite, and ettringite showed an increase in their intensities with increasing curing time attributed to the consolidation of mineral species. The SEM tech-nique results showed that the mortar samples without fly ash addition contained mainly port-landite and ettringite while the samples with cement substitution by 10 and 15% of fly ash at 28 days further contained particles of fly ash coated with portlandite and ettringite, particles with a smooth surface and particles of fly ash with signs of attack on its surface. An increase inc was observed when the age of the mortar and the substitution of Portland cement by fly ash were increased from 3 to 28 days and from 0 to 15% respectively. The maximum value of c was reg-istered for the mortar sample with Portland cement substitution by 15% fly ash at 28 days of curing with 17.38 Mpa.

During submerged laser peening using a pulsed laser, a bubble that behaves like cavitation is generated after laser ablation (LA). The bubble is referred to as laser cavitation (LC). The amplitude of the shock-wave in LA water is larger than that of LC; however, the impact passing through the target metal during LC is larger than that of LA. Thus, submerged laser peening is referred to as “laser cavitation peening”, as the peening method using the cavitation impact is known as “cavitation peening”. The impact induced by a hemispherical bubble is more aggressive than that of a spherical bubble with a microjet. Laser cavitation peening can improve the fatigue strength of metallic materials by producing work-hardening and the introduction of compressive residual stress. Three-dimensional additive manufactured metals (3D metals) such as titanium alloy are attractive materials for aviation components and medical implants; however, the fatigue strength of as-built components is nearly half that of bulk metals, and this is an obstacle for the applications of 3D metals. In the present study, published research papers were reviewed to identify the key factors of laser cavitation peening, with additional visualization of LC and data. Then, improvements in the fatigue strength of metallic materials, including 3D metals produced by laser cavitation peening, were summarized.

Background: Blood flow restriction training (BFRT) uses occlusion during low-intensity resistance training (&lt;50% of repetition maximum, 1RM) to reduce arterial blood flow and venous return, imposing greater metabolic stress but similar muscular hypertrophy and strength gains as high-intensity resistance training (HIRT). However, no study, to date, has incorporated BFRT in a collegiate strength and conditioning setting to assess ecological validity. We aimed to investigate the effects of adding 6-weeks of accessory BFRT or HIRT to NCAA Division III soccer players prescribed resistance training regimen on muscle strength and hypertrophy. Methods: Male and female (n=17) athletes were randomly assigned to complete biceps curls 2x/week under BFRT or control (HIRT), following the regularly scheduled strength training. Bicep strength (1RM) and circumference (BC) were assessed at weeks 0, 3, and 6. Results: In men, no significant interaction between time and condition was observed for BC (p=0.861), though condition (BFRT vs Control, p=0.025) and time (p=0.024) were significant. For 1RM, there was no significant interaction between time and condition (BFRT vs HIRT, p=0.067) or of condition (p=0.598), but there was a significant effect of time (p=0.004). In women, there was no significant interaction between time and condition (p=0.765) or of condition (p=0.971) on BC, but time was significant (p=0.045). For 1RM, there was no significant interaction between time and condition (p=0.227) or of condition (p=0.741), but time was (p=0.018). Conclusion: BFRT induced similar increases in muscle strength and hypertrophy as HIRT in soccer players, suggesting that BFRT could be incorporated into collegiate athlete training.

Self-healing ceramic composites are promising smart materials for high-temperature applications. To better understand their behaviors under service conditions, numerous studies have been performed both experimentally and numerically, and kinetics parameters such as activation energy and frequency factor are reported to be indispensable for investigating healing phenomena. Here, we propose a method for determining the kinetic parameters of self-healing ceramic composites based on the oxidation kinetics model of strength recovery. These parameters are determined by an optimization method using experimental strength recovery data under various healing temperatures and times and microstructural features on the fractured surfaces. Alumina and mullite matrix-based self-healing ceramic composites, such as Al2O3/SiC, Al2O3/TiC, Al2O3/Ti2AlC (MAX phase), and mullite/SiC, were selected as target materials. The theoretical strength recovery behaviors of the cracked specimens obtained from the determined kinetic parameters were compared with the experimental results. The determined parameters are within the previously reported range, and the predicted strength recovery behaviors are reasonably agreed with the experimental values. The proposed method can also be applied to other self-healing ceramics with matrices reinforced with different healing agents to evaluate oxidation rate, crack healing rate, and theoretical strength recovery behaviors for designing self-healing materials used in high temperature applications. Furthermore, the healing ability of composites can be fairly discussed regardless of the type of strength recovery test.

A frequent problem in Geotechnics is the soils with inadequate physical-mechanical properties before the efforts to which they will be subjected by the constructions, incurring cost overruns caused by their engineering improvement. The need to improve the engineering properties of soils is not recent, currently observing that the most common alternatives are binders such as cement and lime. The climate change observed in recent decades and the uncontrolled emission of greenhouse gases have motivated Geotechnical and Geoenvironmental researchers to seek mechanisms for soil reinforcement from a more sustainable and environmentally friendly approach by proposing the use of recycled and waste materials. An alternative is natural fibers, which can be obtained as waste from many agro-industrial processes, implying their high availability and low cost. Sawdust as a by-product of wood processing has a rough texture that can generate high friction between the fiber and the matrix of the soils, leading to a significant increase in its shearing strength and bearing capacity. This concept of improving the properties of soils using natural fibers distributed randomly is inspired by the natural phenomenon of grass and/or plants that when growing on a slope can effectively stabilize a said slope.

The present work was aimed at the investigation of effect of High Energy Ball Milling (HEBM) time on the sintering kinetics, structure, and properties of heavy tungsten alloy (HTA) W-7%Ni-3%Fe. The HTA samples were obtained from the nanopowders (20-80 nm) by conventional liquid phase sintering (LPS) in hydrogen and by Spark Plasma Sintering (SPS) in vacuum. The HTA density was shown to depend on the HEBM time non-monotonously that originates from the formation of non-equilibrium solid solutions in the W-Ni-Fe systems during HEBM. The SPS kinetics of the HTA nanopowders was shown to have a two-stage character, the intensity of which depends on the Coble diffusion creep rate and on the intensity of diffusion of the tungsten atoms in the crystal lattice of the -phase. The kinetics of sintering of the initial submicron powders have a single-stage character originating from the intensity of the grain boundary diffusion in the -phase. The dependencies of the hardness and of the yield strength on the grain sizes were found to obey the Hall-Petch relation. The hardness, strength, and dynamic strength in the compression tests of the fine-grained tungsten alloys obtained by SPS and LPS were studied.

This paper analyzed the main diseases of the friction high-strength bolt (FHSB) joints in order to study the characteristics of the corrosion products of the joints in steel bridge and the influence factors. Seven representative FHSB connection pairs and eight steel plate samples were selected from the Dongying Shengli Yellow River Bridge, which has been in operation for 33 years. Then Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) were used to analyze the microscopic morphology and chemical composition of the corroded surface of the samples. Finally, this paper discussed the relationship between the corroded sample surface and the environmental corrosion. The research results showed that construction quality problems, such as non-standard hole expansion, segmental slab joint dislocation and contact surface pollution, accelerated corrosion of the contact surface. With the increase of corrosion degree of joints, the contact surface of aluminum spraying layer gradually changed from a rugged and dense state to a smooth and porous powder state. With the corrosion of the steel plate substrate, the contact surface gradually changed from a fluffy stratified state to a surface bonding state. It was inferred that the friction coefficient of the FHSB connection node on the corroded aluminum sprayed contact surface first decreased and then increased. The corroded node samples detected not only a large number of S and Cl elements, but also the oxides of Mn, Si and other elements as well as FeS. It was speculated that node corrosion was also related to atmospheric (acid rain) and industrial dust and other corrosive environments. Almost all samples detected the component SiO2 of the Yellow River soil, as well as Mg, Ca, K, Na and other elements at the same time, which is basically consistent with the component elements of the Yellow River soil. Therefore, it was inferred that it was related to the inclusion of the Yellow River soil.

The CuCrSn alloy is promising as high-strength and high-conductivity Cu alloy due to its relative low smelting requirement, while thus far reports on the CuCrSn alloy is still quite lacked. In this study, the microstructure and properties of Cu-0.20Cr-0.25Sn (wt%) specimens prepared under different rolling and aging combinations were comprehensively characterized, in order to reveal the effects of cold rolling and aging on the CuCrSn alloy. The results show that increasing the aging temperature from 400 ºC to 450 ºC can obviously accelerates the precipitation, and the cold rolling before aging significantly increases the initial microhardness and promotes the precipitation. Whereas, the deformation hardening will be eliminated during the aging process, making the microhardness even decrease monotonically when the aging temperature and the rolling ratio before aging are high. Performing the cold rolling after the aging can maximize the effects of precipitation strengthening and deformation strengthening, and its adverse impact on the conductivity is not serious. A tensile strength of 506.5 MPa and a conductivity of 70.33% IACS were obtained with such a treatment, only the elongation decreases. Different strength-conductivity combinations of the CuCrSn alloy can be achieved through appropriate combinations of the aging and post aging cold rolling conditions.

This research investigates the effect of pre-soaking treatment on plant-based aggregate using a wet grout binder to formulate a high-strength lightweight concrete (HSLWC). The surface modification utilising a novel grout soaking technique with various water-to-cement (w/c) ratios indicated a new method of approach for the recent development of lightweight plant-based aggregate (LWPA). In this experiment, the fresh and hardened properties of modified LWPA lightweight concrete were assessed by verifying their workability, densities, compressive and split tensile strengths towards the modulus of elasticity. The results showed that pre-soaking plant-based lightweight aggregate (w/c: 0.6, 0.8, 1.0, and 1.2) slightly increased the density of the samples compared to untreated LWPA. The oven-dry density of treated and untreated LWPA is controlled in the range of HSLWC. The outcomes indicated that the workability of the surface- modified LWPA has significant improvement up to 40% in 6 min for (TDS)/0.6 sample compared to the original LWPA. The mechanical properties of the LWPA concrete with surface modification method exhibit substantial increment of compressive strength, split tensile strength, and modulus of elasticity were recorded at 22%, 26%, and 34%, respectively. Significantly, the findings from this scientific method revealed that the pre-soaking treatment method on LWPA has shown to be a highly recommended technique in improving interfacial bonding while performing as one of the most promising solutions to improve the properties of lightweight concrete.

Indoor localization is an active area of research dominated by traditional machine-learning techniques. Deep learning-based systems have shown unprecedented improvements and have accomplished exceptional results over the past decade, especially the Transformer network within natural language processing (NLP) and computer vision domains. We propose the hyper-class Transformer (HyTra), an encoder-only Transformer with multiple classification heads (one per class) and learnable embeddings, to investigate the effectiveness of Transformer-based models for received signal strength (RSS) based WiFi fingerprinting. HyTra leverages learnable embeddings and the self-attention mechanism to determine the relative position of the wireless access points (WAPs) within the high-dimensional embedding space, improving the prediction of user location. From an NLP perspective, we consider a fixed order sequence of all observed WAPs as a sentence and the captured RSS value(s) for every given WAP at a given reference point from a given user as words. We test our proposed network on public and private datasets of different sizes, proving that the quality of the learned embeddings and overall accuracy improves with increments in samples.

Selective Paste Intrusion (SPI) is an additive manufacturing (AM) process in which thin layers of aggregates are selectively bonded by cement paste only where the structure is to be produced. In this way, concrete elements with complex geometries and structures can be created. Reinforcement is required to increase the flexural strength of the concrete elements and, thus, enable their applicability in practice. Integrating the reinforcement is a difficult task, particularly in the case of SPI due to the layer-wise printing method. Especially with respect to possible complex structures, the production of the reinforcement needs to be adapted to SPI, thereby offering a high degree of freedom. One concept for a reinforcement integration is combining the two additive manufacturing processes SPI and Wire and Arc Additive Manufacturing (WAAM). However, since the two processes serve different fields of application, their compatibility is not necessarily given. Ongoing investigations show that the temperatures caused by WAAM adversely affect both, the cement paste rheology required for sufficient paste penetration into the particle bed and the overall concrete strength. This paper provides an overview of ongoing research focusing on different cooling strategies and their effects on the compressive strength of SPI-printed concrete parts.

There is evidence that Additive Manufacturing plays a crucial role in the fourth industrial revolution. The design freedom provided by this technology is disrupting limits and rules from the past enabling engineers to have new products otherwise unfeasible. Recent developments in the field of SLM have led to a renewed interest in lattice structures that can be produced non-stochastically in previously unfeasible dimensional scales. One of the primary applications is aerospace engineering where the need of lightweight and performance is urgent to reduce the carbon footprint of civil transport around the globe. Of particular concern is fatigue strength. Being able to predict fatigue life in both LCF (Low Cycle Fatigue) and HCF (High Cycle Fatigue) is crucial for a safe and reliable design in aerospace systems and structures. In the present work, an experimental evaluation of compressive-compressive fatigue behavior has been performed to evaluate the fatigue curves of different cells, varying sizes and relative density. A Design of Experiment approach has been adopted in order to maximize the information extractable in a reliable form.

Large inconsistencies in the outcome of precise measurements of Newtonian gravitational ‘constant’ were identified throughout more than three hundred experiments conducted up to date. This paper illustrates the dependency of the Newtonian gravitational parameter on the curvature of the background and the associated field strength of vacuum energy. Additionally, the derived interaction field equations show that boundary interactions and spin-spin correlations of vacuum and conventional energy densities contribute to the emergence of mass. Experimental conditions are recommended to achieve consistent outcomes of the parameter precision measurements, which can directly falsify or provide confirmations to the presented field equations.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

Supplementary cementitious materials (SCMs) are increasingly used in precast concrete industry to enhance concrete strength and durability. SCMs of large market share in precast concrete in-dustry include silica fume, also known as micro-silica and class C fly ash. The main objective of this research is to develop non-proprietary high strength concrete mixes for precast/prestressed concrete industry. Two SCMs are used simultaneously in partial replacement of portland cement to develop ternary mixes. Class c fly ash and silica fume incorporation in the mix design, in ad-dition to low water-to-powder ratio resulted in the successful development of high strength mixes with minimum 24-hour strength in excess of 70 MPa and a final compressive strength ex-ceeding 100 MPa at 28 days. Mechanical properties testing of developed concrete mixes showed that SCMs incorporation resulted in increased values for hardened concrete modulus of elasticity (MoE) and modulus of rupture (MoR). The enhanced concrete properties, mainly high early strength, are highly required in precast concrete industry as it allows for increased productivity of precast facilities and the possibility of pouring high strength slender sections for prestressed concrete applications

This research intended to report amine-functionalized multiwall carbon nanotubes (MWCNTs) prepared by a simple method for efficient and rapid removal of Reactive Yellow 2 (RY2) from water. EDS analysis showed that the N content increased from 0 to 2.42% and from 2.42 to 8.66% after modification by APTES and PEI, respectively. BET analysis displayed that the specific surface area, average pore size, and total pore volume were reduced from 405.22 to 176.16 m2/g, 39.67 to 6.30 nm, and 4.02 to 0.28 cm3/g, respectively. These results proved that the PEI/APTES-MWCNTs were successfully prepared. pH edge experiment indicated that pH 2 was optimal for RY2 removal. At pH 2 and 25 °C, the time required for adsorption equilibrium was 10, 15, and 180 min at initial concentrations of 50, 100, and 200 mg/L, respectively; and the maximum RY2 uptake calculated by the Langmuir model was 714.29 mg/g. Thermodynamic studies revealed that the adsorption process was spontaneous and endothermic. 0-0.1 mol/L of NaCl showed negligible effect on RY2 removal by PEI/APTES-MWCNTs. Five adsorption/desorption cycles confirmed the good reusability of PEI/APTES-MWCNTs in RY2 removal. Overall, the PEI/APTES-MWCNTs are a potential and efficient adsorbent for reactive dye wastewater treatment.

Alloys based on TiNi are widely used in various fields of technology and medicine. In the present work, we report on preparation of TiNi-alloy based wire with the shape memory effect, which was used for compression clips for surgery. Composition and structure of the wire, and its martensitic and physical-chemical properties were studied using SEM, TEM, optic microscopy, profilometry, mechanical tests, etc. The TiNi alloy was found to consist of B2 and B19' and secondary-phase particles of Ti2Ni, TiNi3 and Ti3Ni4. Its matrix was slightly enriched in Ni (50.3 at. % of Ni). Homogeneous grain structure was revealed (an average grain size of 19±0.3 μm) with equal quantities of grain boundaries of special and general types. Surface oxide layer provide improved biocompatibility and promote adhesion of protein molecules. Overall, the obtained TiNi wire was concluded to exhibit martensitic, physical and mechanical properties suitable for its use as an implant material. The wire was then used for manufacturing compression clips with the shape memory effect and applied in surgery. The medical experiment that involved 46 children demonstrated that the use of such clips in children with double-barreled enterostomies permitted to improve the results of surgical treatment.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Collapsibility is an inherent characteristic of loess, which is often treated by adding industrial materials such as cement and lime in engineering, it seriously damages the reclamation performance of soil. Degradable calcium lignosulfonate (CLS) has a good prospect in balancing soil stabilization and environmental protection. Therefore, this paper evaluates the collapsibility and mechanical characteristics of CLS improved loess based on the collapsibility test, grey correlation analysis, and unconfined compressive strength test. The results show that when the content is 3%, the stabilization effect is most obvious, and the collapsibility coefficient can be reduced by more than 95%. The order of grey correlation degree of collapsibility on each index is moisture content, void ratio, dry density, and CLS content from large to small. The unconfined compressive strength increases rapidly in the first 14 days and then decreases with the content. When the content is too high, the strength of improved loess is lower than that of plain loess. Combined with SEM, microstructure parameters, and X-ray diffraction analysis, the carbonate minerals can play the role of filling pores and connecting soil particles, which reduces the grain size of mineral composition and the thickness of the electric double layer and makes the structure more compact. The research results have scientific significance and application value for the ecological modification research and engineering application of soil.

This work communicates cavity ring-down spectroscopy (CRDS) of methylidyne (CH) in a chemiluminescent plasma that is produced in a microwave cavity. Of interest are the rotational lines of the 0-0 vibrational transition for the A-X band and the 1-0 vibrational transition for the B-X band. The reported investigations originate from CH-radical research in 1996 that constituted the first case of applying CRDS to the CH radical. The report also includes recent analysis that shows excellent agreement of measured and computed data, and it communicates CH line strength data.

The results of studying the effect of particles of few-layer graphene (FLG) synthesized by self-propagating high-temperature synthesis (SHS) on the complex of strength and thermo physical properties of polymer composite products obtained by DLP 3D printing are presented. It has been discovered to achieve an increase in thermo physical and strength parameters of polymers modified by FLG compared with samples made on the unmodified base resin. This result was achieved due to low defectiveness, namely the absence of Stone-Wales defects in the structure of FLG due to the homogeneous distribution of FLG over the volume of the polymer in the form of highly dispersed aggregates. It was possible to increase hardness by 120 %, bending strength by 102 %, Charpy impact strength by 205 %, and thermal conductivity at 25 °C by 572 % at concentrations of few-layer graphene of no more than 2 wt. %.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

The solid-state welding method known as friction stir welding (FSW) bonds two metallic work parts, whether the same or different, by plastically deforming the base metal. The frictional resistance between both metallic work pieces causes them to produce heat, which produces plastic deformation and welds them. However, the weldability and strength of FSW joints mainly depend on the FSW parameters. This review work highlights the previous research work on the FSW parameters and their effects on the weldability and quality of the aluminum alloys joined with similar and dissimilar metals through the FSW method. About 150 research studies were systematically reviewed, and the articles included data from peer-reviewed journals. It has been concluded that the key parameters, including welding speed, “rotational speed”, “plunge depth”, “spindle torque”, “shoulder design”, “base material”, “pin profile” and “tool type", significantly affect the weldability of the aluminum joint through the FSW method. Also, the selection of these parameters is important and fundamental as they directly affect the joint. It is recommended that future work focus on FSW for aluminum. Among these, the most essential is the application of artificial intelligence (AI) techniques to select the optimum FSW parameters for aluminum welding.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

Geopolymer is an emerging material alternative to Portland cement and has potential as a refractory material. Adding filler in geopolymer material is a strategy to increase the advantages of its physical and mechanical properties. It has been previously reported that adding nanoparticles can increase the compressive strength value, but there is no reported interaction between nanoparticles and geopolymer during the geopolymerization process. This study aims to study the effect of adding nano-zirconia fillers on the physical and mechanical changes of metakaolin-based geopolymers with nano-zirconia fillers. The geopolymer samples were made with 100 g of metakaolin as the base material and nano-zirconia in amounts of 2 gr, 5 gr, 10 gr, and 15 gr. Further characterization was carried out by XRD, FTIR, and SEM-EDX. This study showed that the compressive strength of the MZr05 sample increased significantly by 58.7% compared to the control sample. The test results of the structure and functional groups did not lead to any new compounds formed in the geopolymerization reaction. Therefore, the interaction of metakaolin geopolymer with nano-zirconia only creates an interfacial bonding.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

All over the world, externally bonded fiber-reinforced polymer systems used to strengthen concrete elements improve building sustainability. However, reports issued by the American Concrete Institute Committee 440 called for heavy scrutinizing before actual field implementation. The very limited number of proposed equations lacks reliability and accuracy. Thus, further investigation in this area is needed. In addition, machine learning techniques are being implemented successfully in developing strength models for complex problems. This study aims to provide a reliable machine learning model based on an experimental database. The proposed model was developed and validated against the experimental database and the very limited models in the literature. The model showed improved agreement with the experimental results compared to the previous models.

This study aims to investigate the effect of banana stem fibers (BSFs) treatment with liquid smoke on changes in the micro-mechanics properties of BSFs, the tensile strength of single fibers, mor-phology, crystalline properties, and functional groups. The research used four model specimen variations, namely fiber without treatment and immersion in liquid smoke for 1, 2, and 3 hours. The BSFs with treatment was dried in an oven with a temperature of 40ºC for 30 minutes. Several tests were conducted, including a tensile test of single fiber capacity of 50N standard ASTM 3379-02, SEM observation, XRD, and FTIR test. The results showed that the highest increase in fiber strength was P2J, which was 264.21 MPa, and the lowest was TP fiber at 148.54 MPa. Fibers treatment with liquid smoke can form strong C-C elemental bonds caused by the H2O degradation process in BSFs, hence carbon atoms (C) are dense, and in conditions of excessive H2O degradation, the fiber strength will become brittle and the liquid smoke can increase the tensile strength of the fiber. The morphology of the fiber changed where the untreated fiber was covered with lignin, while the treated fiber had an elongated rectangular line pattern, porous, and the lignin was eroded. Crystalline properties in the X-ray diffractogram pattern differ between untreated and treated fibers. At an angle of 2ϴ, the lowest diffraction peak is around 160 in untreated wool, and the highest is 230 in treated fiber. The functional group of the fiber has changed where there is a difference in the wave crest between untreated and treatment fiber. The longer immersion time, the element of Carbon (C) will increase. In conclusion, treating BSFs with liquid smoke can change the physical, mechanical, and chemical properties, hence becoming a choice of composite reinforcement material in the future which is lightweight and environmentally friendly.

A simple undirected graph $\Gamma=(V_\Gamma,E_\Gamma)$ admits an $H$-covering if every edge in $E_\Gamma$ belongs to at least one subgraph of $\Gamma$ that isomorphic to a graph $H$. For any graph $\Gamma$ admitting $H$-covering, a total Labelling $\beta: V_\Gamma \cup E_\Gamma \longrightarrow \{1,2,\dots,p\}$ is called an $H$-irregular total $p$-labelling of $\Gamma$ if every two different subgraphs $H_1$ and $H_2$ of $\Gamma$ isomorphic to $H$ have distinct weights where the weight $w_\beta(K)$ of subgraph $K$ of $\Gamma$ is defined as $w_f(K):=\displaystyle \sum_{v\in V_K} f(v) + \sum_{e\in E_K} f(e)$. The smallest number $p$ for which a graph $\Gamma$ admits an $H$-irregular total $p$-labelling is called the total $H$-irregularity strength of $\Gamma$ and is denoted by $ths(\Gamma)$. In this paper, we determine the total $H$-irregularity strength of edge comb product of two graphs.

A total $m$-labelling $\alpha$ on graph $\Gamma$ is called an edge irregular total $m$-labelling if for any two different edges of $\Gamma$, their weights respect to $\alpha$ are distinct, where the weight of any edge is defined as the sum of its label and the labels of its end vertices. We determine the minimum $m$ such that $\Gamma$ can be labelled by an edge irregular total $m$-labelling whenever $\Gamma$ is an odd staircase graph or an even staircase graph.

The optimization of production of lignin-nanofiber-filled thermoplastic starch composite film for potential application in food packaging was carried using Response Surface Methodology (RSM), through the adoption of the Box-Wilson Central Composite Design (CCD) with 1 center point. The effects of filler loading on moisture absorption (MAB), tensile strength [TS], percent elongation [PE] and Young’s modulus [YM]) of the films were investigated in order to construct the desirability indices of the composite. The quality of the fitting model was expressed by the coefficient of determination, R2 and the adjusted R2. Results showed that the nanocomposite films were best fitted by a quadratic regression model with a high coefficient of determination (?2) value. The selected film has desirability of 76.80%, close to the objective function, and contained 4.81% lignin and 5.00% nanofibre. The MAB, TS, YM and PE of the selected film were 17.80 %, 21.51 MPa, 25.76 MPa and 48.81%, respectively. The addition of lignin and nanofiber to starch composite reduced the moisture absorption tendency but increased the mechanical properties of the films due to the good filler/matrix interfacial adhesion. Conclusively, results suggested that these films would be suitable for packaging application.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

Automation of vegetable seedling transplanting has provided opportunities for saving labors and improving productivity. Some changes in seedling agronomy are necessary for efficient transplanting. In this study, the local nursery substrates were added with the herbaceous peat, the sphagnum peat and the coir peat, respectively. Effects of the new compound substrates were investigated on the seedling qualities and the root-substrate strength. In the results, we found that the addition of these horticultural mediums significantly affected the physiochemical properties of the original substrates. Under the same nursery conditions, some appropriate additions could promote the seedling growth. And the deficient or excessive additions were to inhibit the growing development of seedlings and their roots. The corresponding additions would also improve the structural characteristics of the root lumps. Generally, the nursery substrates added with the sphagnum peat were relatively optimized in contribution to the seedling qualities and the root-substrate strength. Especially as the commercial substrate and the sphagnum peat were mixed at the volume ratio of 2:1, the dry matter accumulation of seedlings was 2.18 times more than the original. Their root lumps had the best consolidation strength, which may be an effective application for the necessary qualities of seedlings for automatic transplanting.

Solute decoration at grain boundaries (GB) leads to a number of phenomenon such as changes in interface structure, mobility, cohesion etc. Recent experimental investigations on interfacial segregation in steels are based on microstructural characterisation using two correlative methodologies, namely, Transmission Electron Microscopy-Atom Probe Tomography (APT) and Electron Backscatter Diffraction-APT. Considering the growing interest in this avenue, the present review is aimed at addressing the common adsorption isotherms used for quantifying interfacial segregation and providing an overview of the present state of experimental research in the area of GB segregation in steels. The areas where an understanding of GB segregation may be utilised have also been highlighted with a focus on the experimental challenges associated with understanding GB segregation in steels.

The aim of the study is to assess the loads that are transferred from the main rotor and the tail rotor to the helicopter fuselage. These loads change in the various phases of the transient flight as a result of the variable control of the maneuver and as a result of the variable flow around the blades. The knowledge of the loads allows for the proper selection of the level of excitations that should load the fuselage structure during fatigue and strength tests. The simulation model describing the helicopter flight is discussed. This model takes into account the motion of each blade relative to its hinges. Results are shown for two maneuvers - pullup/pushover and diving. The values of extreme loads transferred to the fuselage were obtained.

The objective was to assess the instrumental validity and the test-retest reliability of a low-cost hand-held push dynamometer adapted from a load-cell based hanging scale (tHHD) to collect compressive forces in different ranges of compressive forces. Three independent raters applied 50 pre-established compressions each on the tHHD centered on a force platform in 3 distinct ranges: ~70 N, ~160 N, ~250 N. Knee isometric strength was also assessed on 19 subjects in two sessions (48h apart) using the tHHD anchored by an inelastic adjustable strap. Knee extension and flexion were assessed with the participant seated on a chair with the feet resting on the floor, knees, and hips flexed at 90°. The isometric force peaks were recorded and compared. The ICC and the Cronbach’s α showed excellent consistency and agreement for both instrumental validity and test-retest reliability, as the correlation and determination coefficients. The SEM and the MDC analysis returned adequate low values with a coefficient of variation less than 5%. The Bland-Altman results showed consistency and high levels of agreement. The tHHD is a valid method to assess the knee isometric strength, showing portability, cost-effectiveness, and user-friendly interface to provide an effective form to assess the knee isometric strength.

Purpose: While resultant maximal voluntary contraction (MVC) is commonly used to assess muscular performance, the simultaneous activation of antagonist muscles could dramatically underestimate the strength of the agonist muscles. While quantification of antagonist torque has been performed in plantar- (PF) and dorsi-flexion (DF) joint in isometric conditions, it has yet to be determined in anisometric (concentric and eccentric) conditions. Methods: The experiment was performed in 9 participants through 2 sessions (reliability). The MVCs in DF and PF were measured in isometric, concentric and eccentric conditions (10°.s^-1). Electromyographic (EMG) activities from the soleus, gastrocnemius medialis and lateralis, and tibialis anterior muscles were simultaneously recorded. The EMG biofeedback method was used to quantify antagonist torque, where participants were asked to maintain a level of EMG activity, corresponding to antagonist EMG activity and related to the muscle contraction type, according to a visual EMG bio-feedback displayed on a screen. Results: Resultant torque significantly underestimated agonist torque in DF MVC (30-65%) and to a lesser extent in PF MVC (3%). Triceps surae antagonist torque was significantly modified with muscle contraction type, showing higher antagonist torque in isometric (29 Nm) than eccentric (23 Nm, p < 0.001) and concentric (14 Nm, p < 0.001) conditions and resulting in modification of the DF MVC torque-velocity shape. The difference between DF eccentric and concentric MVC was attenuated when considered agonist torque (12%) rather than resultant torque (45%). Conclusion: Estimation of the antagonist torque in isometric or anisometric condition brings new insights to assessment of muscular performance and could result in costly misinterpretation in strength training and/or rehabilitation programs.

Abstract: During firing from a mortar, an important issue is the parameters of compressibility of the ground on which the mortar is placed. This affects the operation of the mortar (including safety). During the qualification tests of the mortar, the influence of different types of substrate on its strength and work during shooting should be examined. Until now in the Polish standardization documents was no clear description about the substrate parameters used for this kind of tests. Analysis of the literature also did not allow to determine the dependence of the mortars displacement in the function of the type of substrate and its geotechnical parameters. Therefore, the authors carried out analytical and experimental analysis of the use of geotechnical methods to determine the parameters of the substrate for mortar testing. The paper presents the proposed types of standardized soil and their research methods. Preliminary tests were also carried out using the prescribed measurement methods and a comparative mortar firing test. Subsequently, an analysis of the results was carried out and the possibilities of using the proposed methods of measuring the parameters of soil compressibility were determined.

The relative force strengths of the Coulomb forces, gravitational forces, dark matter forces, weak forces and strong forces are compared for the dark matters, leptons, quarks, and normal matters (p and n baryons) in terms of the 3-D quantized space model. The quark confinement and asymptotic freedom are explained by the CC merging to the A(CC=-5)₃ state. The proton with the (EC,LC,CC) charge configuration of p(1,0,-5) is p(1,0) + A(CC=-5)₃. The A(CC=-5)₃ state has the 99.6% of the proton mass. The three quarks in p(1,0,-5) are asymptotically free in the EC and LC space of p(1,0) and are strongly confined in the CC space of A(CC=-5)₃. This means that the lepton beams in the deep inelastic scattering interact with three quarks in p(1,0) by the EC interaction and weak interaction. Then, the observed spin is the partial spin of p(1,0) which is 32.6 % of the total spin (1/2) of the proton. The A(CC=-5)₃ state has the 67.4 % of the proton spin. This explains the proton spin crisis. The EC charge distribution of the proton is the same to the EC charge distribution of p(1,0) which indicates that three quarks in p(1,0) are mostly near the proton surface. From the EC charge distribution of neutron, the 2 lepton system (called as the koron) of the koron is, for the first time, reported in the present work.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

This paper presents a comparison between indirect methods for assessing the buildability of 3D printed cementitious materials, including CRV or CSR test using rotational rheometry, unconfined uniaxial compression test (UUCT), a newly proposed confined uniaxial compression test (CUCT), and fast penetration test. The experimental program was conducted on the extruded samples of six printable mortars and two printable concretes with various rheological behavior achieved by the use of different additives and admixtures. Predictions of the material failure and the stability failure in hollow cylindrical structures are provided and compared with the results of the direct printing test. Benefits and disadvantages of the employed test methods are discussed, also taking into consideration a perspective of their use for automated in-situ control of the materials’ buildability.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

The oil and gas sector has recognised structural integrity assessment of ageing platform for prospective life extension as a rising concern, particularly in encountering the randomness of the harsh ocean environments. This condition leads to uncertainty in wave-in-deck load estimates and a high load level being imposed on offshore structures. This emphasises the necessity of enhanced reliability, as failure might result in inaccessibility because of the uncertainties related to long-distance services, such as accuracy of predictions of loads and responses. Even though the established guidelines present a fundamental assessment, additionally, comprehensive rules are required. This paper performed a reliability analysis incorporating practical approaches that can more accurately represent time-dependent structural deterioration. The following two procedures have been adopted by a majority of significant oil and gas operators to monitor the safety and integrity of these structures: a) Ultimate Strength Assessment (USA) method and b) Reliability Design Assessment (ReDA) method. A comparison of these two reliability approaches was performed on selected ageing jacket structures in the region of the Malaysian sea. The comparative findings, namely, reserve strength ratio (RSR) at various years of the return period (RP) and ratio value for risk of failure regarding the probability of failure (POF), provided a check and balance in strengthening confidence in the results. The findings showed that the structural components might safely survive either using the USA and ReDA method in such conditions, as the reliability indexes were determined to be satisfactory compared to allowable values from ISO 19902 design specifications. Therefore, these evaluations were determined to control the risk level of the structure during the remaining of its lifetime and undertake cost-effective inspections or mitigation strategies when necessary.

In the modern world, all manufacturers strive for the optimal design of their products. This general trend is recently also observed in the corrugated board packaging industry. Colorful prints on displays, perforations in shelf-ready-packaging and various types of ventilation holes in trays, although extremely important for ergonomic or functional reasons, weaken the strength of the box. To meet the requirements of customers and recipients, packaging manufacturers outdo each other in new ideas for the construction of their products. Often the aesthetic qualities of the product become more important than the attention to maintaining the standards of the load capacity of the packaging (which, apart from their attention-grabbing functions, are also intended to protect transported products). The particular flaps design (both top and bottom) and their influence on the strength of the box is investigated in this study. The updated analytical-numerical approach is used here to predict the strength of the packaging with various flap’s offsets. Experimental results indicated a significant decrease in the static load-bearing capacity of packaging in the case of shifted flap creases. The simulation model proposed in our previous work has been modified and updated to take into account also this effect. The results obtained by the model presented in the paper are in satisfactory agreement with the experimental data.

Nowadays, we use social networks such as Twitter, Facebook, WeChat and Weibo as means to communicate with each other and get to know others. Gradually social networks has become indispensable in our everyday life, and we cannot absolutely imagine what the daily life would be like without social networks. Through social networks, we can access friends' opinions and behaviors easily and are influenced by them in turn. Thus, an effective algorithm to find the top-K influential nodes (the problem of influence maximization) in the social network is critical for various downstream tasks such as viral marketing, anticipating natural hazards, reducing gang violence, public opinion supervision etc. Solving the problem of influence maximization in real-world propagation scenarios often involves estimating influence strength (influence probability between two nodes), which cannot directly observed. To estimate influence strength, conventional approaches propose various humanly-devised rules to extract features of user interactions, the effectiveness of which heavily depends on domain expert knowledge. Besides, they are often applicable for special scenarios or specific diffusion models. Consequently, they are difficult to be generalized into different scenarios, diffusion models and even domains. Inspired by the powerful ability of neural networks in the field of representation learning, we design a deep hierarchical network embedding model HGE to map nodes (with attributes) into latent space automatically. In general, HGE takes an attributed social network as the input for learning latent network representation of each node, incorporating hierarchical community structure, node attributes and general network structure into a unified deep generative framework. Then, with the leaned latent representation of each node, we propose a HGE-GA algorithm to predict influence strength and compute the top-K influential nodes through a greedy-based maximization algorithm. Extensive experiments on real-world attributed networks demonstrate the outstanding superiority of the proposed HGE model and HGE-GA algorithm compared with the state-of-the-art methods, verifying the effectiveness of the proposed model and algorithm.

Objectives: In order to solve the problem that most of the existing research focuses on the binary tactile attributes of objects,which ignores the tactile attribute strength and category recognition,an attribute strength and category recognition method based on convolutional neural network matrix-label is proposed. Methods:Firstly,in the data preparation stage,we preprocess the raw data and determine the matrix labels to build the haptic dataset.Secondly,in the feature extraction stage,we fuse the haptic data of two fingers and use the convolutional neural network to extract the attribute strength features.Finally,in the attribute strength and category recognition stage,all channel haptic data is fused to predict the attribute strength and category.Results:We compared with the multi-label convolutional neural network method in terms of elastic strength,hardness strength and category,and compared the attribute strength recognition capabilities of the two methods using novel objects outside the haptic dataset.The results show that the accuracy of the last 20 iterations of the matrix-label method has an average elastic strength of 96.73%,hardness strength of 97.34%,and category of 96.67%.The performance is better.When the Euclidean distance between the prediction of the novel object and the real label is less than 1,the accuracy of the elastic strength is best to reach 100%,and the hardness strength is best to reach 100%.The performance is better. Conclusions:The effectiveness of the method has been verified.Comparing with the convolutional neural network method,our method can effectively recognize the attribute strength and category of objects.

A semi-structured interview (SSI) is one of the essential tools in conduction qualitative research. This essay draws upon the pros and cons of applying semi-structured interviews (SSI) in the qualitative research method. Moreover, the challenges of SSI during the coronavirus pandemic are critically discussed to provide plausible recommendations.

With global warming and accelerated degradation of permafrost, the engineering problems caused by the formation of weak zones between the shallow and permafrost layers of soil–rock mixture (S-RM) slopes in permafrost regions have become increasingly prominent. To explore the influence of rock content on the shear strength of the S-RM freezing–thawing interface, the variation in the shear strength for different rock content is studied herein using direct shear tests. In addition, a 3D laser scanner is used for obtaining the topography of the shear failure surface. Combined with the analysis results of the shear band-particle calculation model, the influence of the rock content on the shear strength of the interface is explored. It was found that the impact threshold of the rock content on the interface strength and failure mode is approximately 30%, when the rock content (R) is &gt; 30% and that the shear strength increases rapidly with increasing rock content. When R ≤ 30%, the actual shear plane is similar to waves; when R &gt; 30%, the shear plane appears as gnawing failure. The shear strength of S-RM freezing–thawing interface mainly comes from the bite force and friction between particles. The main reason for the increase in shear strength with increasing rock content is the increase in bite force between particles, which makes the ratio of bite force to friction force approximately 1:1.

High-strength low-alloy steels (HSLAs) are widely used in the structural body components of many domestic motor vehicles owing to their better mechanical properties and greater resistance. The real production process of HSLA steelmaking can be regarded as a model that builds on the relationship between process parameters and product quality attributes. A surrogate modeling method is used, and the resulting production process model can be applied to predict the optimal manufacturing process parameters. We used different methods in this paper to build such a surrogate model, including linear regression, random forests, support vector regression, multilayer perception, and a simplified VGG model. We then applied three bio-inspired search algorithms, namely particle swarm optimization, the artificial bee colony algorithm, and the firefly algorithm, to search for the optimal controllable manufacturing process parameters. Through experiments on 9,000 test samples used for building the surrogate model, and 299 test samples for making the optimal process parameter selection, we found that the combination of a simplified VGG model and the firefly algorithm was the most successful at reaching a success rate of 100%—in other words, when the product quality attributes of all test samples satisfy the mechanical requirements of the end products.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.