Process simulation represents an important tool for plant design and optimisation, either applied to well established or to newly developed processes. Suitable thermodynamic packages should be selected in order to properly describe the behaviour of reactors and unit operations and to precisely define phase equilibria. Moreover, a detailed and representative kinetic scheme should be available to predict correctly the dependence of the process on its main variables. This review points out some models and methods for kinetic analysis specifically applied to the simulation of catalytic processes, as a basis for process design and optimisation. Attention is paid also to microkinetic modelling and to the methods based on first principles, to elucidate mechanisms and calculate thermodynamic and kinetic parameters. Different case histories support the discussion. At first, we have selected two basic examples from the industrial chemistry practice, e.g. ammonia and methanol synthesis, which may be described through a relatively simple reaction pathway. Then, a more complex reaction network is deeply discussed to define the conversion of bioethanol into syngas/hydrogen or into building blocks, such as ethylene.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

Network Simulators is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. Many problems can be solved by using network simulators such as NS-3. With this in mind, the aim of this article is to introduce new NS-3 users through detailed information. It is sometimes difficult to handle by new users the traditional manuals developed by NS-3 project official website. In this article, NS-3 for communication network and Eclipse Integrated Development Environment (IDE) for powerful programming language are integrated step-by-step, explaining the main features of these open source software packages and concluding with an example simulation. Our effort is to make it easy for a beginner to be part of the NS-3 research community and to maintain an open environment of knowledge.

The production of lithium-ion battery cells is characterized by a high degree of complexit due to numerous cause-effect relationships between process characteristics. Knowledge about the multi-stage production is spread among several experts, rendering tasks such as failure analysis challenging. In this paper, a method is presented, which includes expert knowledge acquisition in production ramp-up by combining Failure Mode and Effects Analysis (FMEA) with a Bayesian Network. We show the effectiveness of this holistic method by building up a large scale, cross-process Bayesian Failure Network in lithium-ion battery production. Using this model, we are able to conduct root cause analyses as well as analyses of failure propagation. The former support operators in identifying root causes once a cell possesses a specific failure by calculating most-probable explanations matched to the individual battery cell data. The latter enable us to analyze propagation of failures and deviations in the production chain and thus provide support for placement of quality gates, leading to a significant reduction in scrap rate. Moreover, it gives an insight into which process steps are key drivers for which final product characteristics.

Dump design and scheduling are critical elements to effective mine planning, especially if several of them are required in large-scale open pit mines. Infrastructure capital and transportation costs are considerable from an early stage in the mining project, and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modelling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to model and optimize the design of a mine dump by minimizing the total haulage costs. The proposed methodology consists on: (i) Formulation of a dump model based on a system of equations relying on multiple relevant parameters; (ii) Solves by minimizing the total cost using linear programming and determines a ‘preliminary’ dump design; (iii) Through a series of iterations, modifies the ‘preliminary’ footprint by projecting it to the topography and creates the ultimate dump design. Finally, an example application for a waste rock dump illustrates this methodology.

This paper describes a case study for applying of hybrid-electric propulsion system for a general aviation aircraft. The work was performed by a joint team of CIRA and the Department of Industrial Engineering of the University of Naples “Federico II”. Electric and hybrid electric propulsion for aircraft has gained widespread and significant attention over the past decade. The driver for industry interest has principally been the need to reduce emissions of combustion engine exhaust products and noise, but increasingly studies revealed potential for overall improvement in energy efficiency and mission flexibility of new aircraft types. The project goal was to demonstrate feasibility of aeronautic parallel hybrid-electric propulsion for a Light aircraft varying the mission profiles and the electric configuration. Through a creation, and application, of a global model, with software AMESim^®, in which it can be represented everything about the components chosen by the industrial partners, some interesting considerations are carried out. In particular, it was confirmed that with the only integration of state of the art technologies, for some particular missions, the advantages of aircraft hybrid-electric propulsion, for light aircraft, are notable.

Quantum computers are machines that are designed to use quantum mechanics in order to improve upon classical computers by running quantum algorithms. One of the main applications of quantum computing is solving optimization problems. For addressing optimization problems we can use linear programming. Linear programming is a method to obtain the best possible outcome in a special case of mathematical programming. Application areas of this problem consist of resource allocation, production scheduling, parameter estimation, etc. In our study, we looked at the duality of resource allocation problems. First, we chose a real world optimization problem and looked at its solution with linear programming. Then, we restudied this problem with a quantum algorithm in order to understand whether if there is a speedup of the solution. The improvement in computation is analysed and some interesting results are reported.

Agricultural greenhouse is largely answered in the agricultural sphere, despite the shortcomings it has, including overheating during the day and night cooling which sometimes results in the thermal inversion mainly due to its low inertia. The glasshouse dressed chapel is relatively more efficient than the conventional tunnel greenhouse. Its proliferation on the ground is more or less timid because of its relatively high cost[14-22]. Agricultural greenhouse aims to create a favorable microclimate to the requirements of growth and development of culture, from the surrounding weather conditions, produce according to the cropping calendars fruits, vegetables and flower species out of season and widely available along the year. It is defined by its structural and functional architecture, the quality thermal, mechanical and optical of its wall, with its sealing level and the technical and technological accompanying[12-13]. The greenhouse is a very confined environment, where multiple components are exchanged between key stakeholders and them factors are light, temperature and relative humidity[8]. This state of thermal evolution is the level sealing of the cover of its physical characteristics to be transparent to solar, absorbent and reflective of infrared radiation emitted by the enclosure where the solar radiation trapping effect otherwise called "greenhouse effect" and its technical and technological means of air that accompany. The socio-economic analysis of populations in the world leaves appear especially the last two decades of rapid and profound transformations These changes are accompanied by changes in eating habits, mainly characterized by rising consumption spread along the year[14]. To effectively meet this demand, greenhouse-systems have evolved, particularly towards greater control of production conditions (climate, irrigation, ventilation techniques, CO2 supply, etc ...). Technological progress has allowed the development of greenhouses so that they become increasingly sophisticated and of an industrial nature (heating, air conditioning, control, computer, regulation, etc ...). New climate driving techniques have emerged, including the use of control devices from the classic to the use of artificial intelligence[10-11] such as neural networks and / or fuzzy logic, etc... As a result, the greenhouse growers prefer these new technologies while optimizing the investment in the field to effectively meet the supply and demand of these fresh products cheaply and widely available throughout the year.

Star block-copolymers (SBCs) are macromolecules formed by a number of diblock copolymers anchored to a common central core, being the internal monomers solvophilic and the end monomers solvophobic. Recent studies have demonstrated that SBCs constitute a self-assembling building blocks with specific softness, functionalization, shape, and flexibility. Depending on different physical and chemical parameters the SBCs can behave as flexible patchy particles. In this paper, we study the rotational dynamics of isolated SBCs using a hybrid mesoscale simulation technique. We compare three different approaches to analyse the dynamics: the laboratory frame, the non-inertial Eckart's frame, and a geometrical approximation relating the conformation of the SBC to the velocity profile of the solvent. We find that the geometrical approach is adequate when dealing with very soft systems while in the opposite extreme, the dynamics is best explained using the laboratory frame. On the other hand, the Eckart frame is found to be very general and to reproduced well both extreme cases. We also compare the rotational frequency and the kinetic energy with the definitions of the angular momentum and inertia tensor different from recent publications.

The hybrid system is analyzed and optimized to produce electric energy in Non-Interconnected Zones in the Colombian Caribbean region, contributing both to the improvement in the reduction of greenhouse gas emissions and to the rational use of energy. A comparative analysis of the performance of these systems was carried using a dynamic model in real wind and solar data. The model is integrated by a Southwest Wind Power Inc. wind turbine. AIR 403, a proton exchange fuel cell (PEM), an electrolyze, a solar panel and a charge regulator based on PID controllers to manipulate oxygen and hydrogen flows in the cell. The transient responses of the cell voltage, current, and power were obtained for the demand of 200 W for changes in solar radiation and wind speed for all days of the year 2013 in the Ernesto Cortissoz airport, Puerto Bolívar, Alfonso Lopez airport and Simon Bolívar airport, by regulating the flow of hydrogen and oxygen into the fuel cell. The maximum contribution of power generation from the fuel cell was presented for the Simon Bolívar airport in November with a value of 158,358W (9.45%). A multi-objective design optimization under a Pareto front is presented for each place studied to minimize the Levelized Cost of Energy and CO₂ emission, where the objective variables are the number of panel and stack in the PV system and PEM.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

Entanglement is at the heart of quantum technologies such as quantum information and quantum metrology. Providing larger quantum Fisher information (QFI), entangled systems can be better resources than separable systems in quantum metrology. QFI topic is a very active research area and it has many possible usage areas in quantum information domain. In this study, we review quantum Fisher information research with both from theoritical and application perspective.

Industries, which are mainly responsible for high energy consumptions, need to invest in research projects in order to develop new managing systems for rational energy use and to tackle the devastating effects of climate change caused by human behavior. The study reported in this paper concerns the forging industry, where the production processes generally start with the heating of the steel in furnaces and continue with other processes, such as heat treatments and mechanical machining. One of the most critical operations, in terms of energy loss, is the opening of the furnace doors for the insertion and extraction operations. During this time, the temperature of the furnaces decreases by hundreds of degrees in a few minutes. Because the dispersed heat needs to be supplied again through the combustion of fuel, increasing the consumption of energy and the pollutant emissions, the evaluation of the amount of the lost energy is crucial for the development of operating or mechanical systems able to contain this dispersion. To perform this study, CFD simulation software was used. Results show that at the door opening, because of temperature and pressure differences between the furnace and the ambient, turbulences are generated. Results also show that the amount of energy lost for an opening of 10 minutes for radiation, convection and conduction is equal to 5606 MJ where convection is the main contributor with 5020 MJ. The model created, after being validated, has been applied to perform other simulations in order to improve the energy performance of the furnace. Results show that a reduction of the opening time of the door allows energy savings and limits pollutant emissions.

We review and assess the classic SIR and SEIR epidemiological models regarding possible applications to the COVID-19 pandemic. In spite of numerous more complicated models, we show how the qualitative features of the solution to the SIR and SEIR models continue to provide valuable public health insights in some scenarios. Using estimated COVID-19 data as of this date, the SEIR model shows that if it were possible to reduce R₀ from 2.5 to 1.25 through social distancing and other measures, the maximum fraction of the population that would become infected at any particular time would drop from 17% to 4%, provided that all of the model assumptions are satisfied. Finally, we compare the classic SIR model with a recent stochastic model with favorable results. Since this comparison underscores the importance of underlying connectivity assumptions, we conclude with Monte-Carlo simulations with specific connectivity that reproduce the classical SIR model with standard incidence.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Network Simulators (NS) is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. This is the case of Mobile Ad hoc Networks (MANETs) which can be extensively used in emergency situations or to gather information without infraestructure. An important factor to get realiable results in the MANETs’ simulations is the wireless channel module of NSs. In this report, we explain how thw wireless channel is implemented in NS-3 and it can be configured.

Hydraulic fracturing in shale gas reservoirs has usually resulted in complex fracture network. The results of micro-seismic monitoring showed that the nature and degree of fracture complexity must be clearly understood to optimize stimulation design and completion strategy. This is often called stimulated reservoir volume (SRV). In the oil & gas industry, stimulated reservoir volume has made the shale gas exploitation and development so successful, so it is a main technique in shale gas development. The successful exploitation and development of shale gas reservoir has mainly relied on some combined technologies such as horizontal drilling, multi-stage completions, innovative fracturing, and fracture mapping to engineer economic completions. Hydraulic fracturing with large volumes of proppant and fracturing fluids will not only create high conductivity primary fractures but also stimulate adjacent natural fractures. Fracture network forming around every hydraulic fracture yields a stimulated reservoir volume. A model of horizontal wells which was based on a shale gas reservoir after volume fracturing in China was established to analyze the effect of related parameters on the production of multi-fractured horizontal wells in this paper. The adsorbed gas in the shale gas reservoir is simulated by dissolved gas in the immobile oil. The key to simulate SRV is to accurately represent the hydraulic fractures and the induced complex natural fracture system. However, current numerical simulation methods, such as dual porosity modeling, discrete modeling, have the following limitations: 1) time-consuming to set up hydraulic and natural fracture system; 2) large computation time required. In this paper, the shape of the stimulated formation is described by an expanding ellipsoid. Simplified stimulated zones with higher permeability were used to model the hydraulic fracture and the induced complex natural fracture system. In other words, each primary fracture has an enhanced zone, namely SRV zone. This method saves much developing fine-grid time and computing time. Compared with the simulation results of fine-grid reference model, it has shown that this simplified model greatly decreases simulation time and provides accurate results. In order to analyze the impacts of related parameters on production, a series of simulation scenarios and corresponding production performance were designed. Optimal design and analyses of fracturing parameters and the formation parameters have been calculated in this model. Simulation results showed that the number of primary fractures, half length, SRV half-width and drop-down have great effects on the post-fracturing production. Formation anisotropies also control the production performance while the conductivity of the primary fractures and SRV permeability do not have much impact on production performance. The complexity of stimulated reservoir volume has strong effect on gas well productivity. Fracture number mainly affects the early time production performance. The increase of SRV width cannot enlarge the drainage area of the multi-fractured horizontal wells, but it can improve the recovery in its own drainage region. Permeability anisotropies have much effect on production rate, especially the late time production rate. The results prove that horizontal well with volume fracturing plays an irreplaceable role in the development of ultra-low permeability shale gas reservoir.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

The process of modelling energy systems is accompanied by challenges inherently connected with mathematical modelling. However, due to modern realities in the 21st century, existing challenges are gaining in magnitude and are supplemented with new ones. Modellers are confronted with a rising complexity of energy systems and high uncertainties on different levels. In addition, interdisciplinary modelling is necessary for getting insight in mechanisms of an integrated world. At the same time models need to meet scientific standards as public acceptance becomes increasingly important. In this intricate environment model application as well as result communication and interpretation is also getting more difficult. In this paper we present the open energy modelling framework (oemof) as a novel approach for energy system modelling and derive its contribution to existing challenges. Therefore, based on literature review, we outline challenges for energy system modelling as well as existing and emerging approaches. Based on a description of the philosophy and elementary structural elements of oemof, a qualitative analysis of the framework with regard to the challenges is undertaken. Inherent features of oemof such as the open source, open data, non-proprietary and collaborative modelling approach are preconditions to meet modern realities of energy modelling. Additionally, a generic basis with an object-oriented implementation allows to tackle challenges related to complexity of highly integrated future energy systems and sets the foundation to address uncertainty in the future. Experiences from the collaborative modelling approach can enrich interdisciplinary modelling activities. Our analysis concludes that there are remaining challenges that can neither be tackled by a model nor a modelling framework. Among these are problems connected to result communication and interpretation.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

In this work, we'll present the power spectra density, auto-correlation function, dentrended fluctuation analysis and multifractal spectrum are performed to the daily light curves of Blazars monitored by Fermi LAT. Some signs of power law are found.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

Visual inertial odometry (VIO) has recently received much attention for efficient and accurate ego-motion estimation of unmanned aerial vehicle systems (UAVs). Recent studies have shown that optimization-based algorithms achieve typically high accuracy when given enough amount of information, but occasionally suffer from divergence when solving highly non-linear problems. Further, their performance significantly depends on the accuracy of the initialization of inertial measurement unit (IMU) parameters. In this paper, we propose a novel VIO algorithm of estimating the motional state of UAVs with high accuracy. The main technical contributions are the fusion of visual information and pre-integrated inertial measurements in a joint optimization framework, and the stable initialization of scale and gravity using relative pose constraints. To count for ambiguity and uncertainty of VIO initialization, a local scale parameter is adopted in the online optimization. Quantitative comparisons with the state-of-the-art algorithms on the EuRoC dataset verify the efficacy and accuracy of the proposed method.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

Kelly's Criterion is well known among gamblers and investors as a method for maximizing the returns one would expect to observe over long periods of betting or investing. These ideas are conspicuously absent from portfolio optimization problems in the financial and automation literature. This paper will show how Kelly's Criterion can be incorporated into standard portfolio optimization models. The model developed here combines risk and return into a single objective function by incorporating a risk parameter. This model is then solved for a portfolio of 10 stocks from a major stock exchange using a differential evolution algorithm. Monte Carlo calculations are used to verify the accuracy of the results obtained from differential evolution. The results show that evolutionary algorithms can be successfully applied to solve a portfolio optimization problem where returns are calculated by applying Kelly's Criterion to each of the assets in the portfolio.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

The existence of multiple copies of genes is a well-known phenomenon. A gene family is a set of sufficiently similar genes, formed by gene duplication. In earlier works conducted on limited number of completely sequenced and annotated genomes it was found that size of gene family and size of genome are positively correlated. Additionally, it was found that several atypical microbes deviated from the observed general trend. In this study, we reexamined these associations on a larger dataset consisting of 1484 prokaryotic genomes and using several ranking approaches. We applied ranking methods in such a way that genomes with lower number of paralogs would have lower rank. Until now only simple ranking methods were used; we applied the Kemeny optimal aggregation approach as well. Regression and correlation analysis were utilized in order to accurately quantify and characterize the relationships between measures of paralog indices and genome size. In addition, boxplot analysis was employed as a method for outlier detection. We found that, in general, all paralog indexes positively correlate with an increase of genome size. As expected, different groups of atypical prokaryotic genomes were found for different types of paralog quantities.

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

Caveolin-1 (Cav-1) is 22 kDa caveolae protein, acts as a scaffold within caveolar membranes. It interacts with alpha subunits of G-protein and thereby regulates their activity. Earlier studies reported elevated or up-regulated levels of caveolin-1 in the serum of prostate cancer patients. Secreted Cav-1 promotes angiogenesis, cell proliferation and anti-apoptotic activities in prostate cancer patients. Cav-1 upregulation is mainly related to prostate cancer metastasis. Keeping above facts in view, the present study was designed to explore Cav-1 as a target for prostate cancer therapy using computational approach. Molecular docking, structural base molecular modelling and molecular dynamics simulations were performed to investigate Cav-1 inhibitors. A predictive model was generated and validated to establish a stable structure. ZINC database of biogenic compounds was used for induced fit docking (IFD) and high throughput virtual screening. The H-bond interactions of the compounds with active site residues of Cav-1 were estimated by IFD and 100 ns long molecular dynamic simulations. The reported compounds showed significant binding and thus can be considered as potent therapeutic inhibitors of Cav-1. This study provides a valuable insight into biochemical interactions of Cav-1 for therapeutic applications and warrants for experimental validation of the predicted ‘active(s)’.

The greenhouse gases and air pollution generated by extensive energy use have exacerbated climate change. An electric-bus (e-bus) transportation system favors reducing pollution and carbon emissions. This study analyzed the minimization of construction costs for an all battery-swapping public e-bus transportation system. A simulation was conducted according to existing timetables and routes. Daytime charging was incorporated during the hours of operation; the two parameters of the daytime charging scheme were the residual battery capacity and battery-charging energy during various intervals of daytime peak electricity hours. The parameters were optimized using three algorithms: particle swarm optimization (PSO), a genetic algorithm (GA), and a PSO–GA. This study observed the effects of optimization on cost changes (e.g., number of e-buses, on-board battery capacity, number of extra batteries, charging facilities, and energy consumption) and compared the plug-in and battery-swapping e-bus systems. The results revealed that daytime charging can reduce the construction costs of both systems. In contrast to the other two algorithms, the PSO–GA yielded the most favorable optimization results for the charging scheme. Finally, according to the cases investigated and the parameters of this study, the construction cost of the plug-in e-bus system was lower than that of the battery-swapping e-bus system.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Quantum computers are machines that are designed to use quantum mechanics in order to improve upon classical computers by running quantum algorithms. One of the main applications of quantum computing is solving optimization problems. For addressing optimization problems, we can use linear programming. Linear programming is a method to obtain the best possible outcome in a special case of mathematical programming. Application areas of this problem consist of resource allocation, production scheduling, parameter estimation, etc. In our study, we look at quantum speedup ratios of HHL Algorithm for different scenarios of linear programming. In a first scenario we look quantum speedup ratio (S(N)) as a function of phase transition and the ratio (κ) between the greatest and smallest eigenvalues of the matrix in linear equation system. As a second scenario, we investigate the changes in S(N) as a function of κ and s, which is the coefficient for defining the matrix as s-sparse.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

Energy system models have become indispensable to shape future energy systems by providing insights into different trajectories. However, sustainable systems with high shares of renewable energy are characterized by growing cross-sectoral interdependencies and decentralized structures. To capture important properties of increasingly complex energy systems, sophisticated and flexible modelling tools are needed. At the same time open science becomes increasingly important in energy system modelling. This paper presents the Open Energy Modelling Framework (oemof) as a novel approach in energy system modelling, representation and analysis. The framework forms a toolbox to construct comprehensive energy system models and has been published open source under a free license. With a collaborative development based on open processes the framework seeks for a maximum level of participation and transparency to facilitate open science principles in energy system modelling. Based on a generic graph based description of energy systems it is well suited to flexibly model complex cross-sectoral systems and incorporate various modelling approaches. This makes the framework a multi-purpose modelling environment for modelling and analyzing different systems ranging from an urban to a transnational scale.

In order to improve the performance of the draft tube in hydraulic turbine, a multi–objective optimization method for the draft tube is developed by combining the design of experiment (DOE), the radial basis function (RBF) and the non–dominated sorting genetic algorithm (NSGA–II) in this paper. The geometrical design variables of the median section in the draft tube and the cross section in its exit diffuser are considered as design parameters in this optimization, which objective function is to maximize the pressure recovery factor (Cp) and minimize the energy loss coefficient (ζ). The limited numbers of design matrix required for the shape optimization of the draft tube is generated by optimal Latin hypercube (OLH) method of the DOE technique, of which performances are evaluated through computational fluid dynamic (CFD) numerical simulation. For reducing of the computational consumption, the approximate model is used based on the RBF. The Pareto optimal solutions are finally performed using the NSGA–II for obtaining the best geometrical parameters of the draft tube. The optimization result of the draft tube shows a marked performance improvement over the original, which verifies the theoretical validity and feasibility of the proposed method in this paper.

In the present study, a hybrid optimizing algorithm has been proposed using Genetic Algorithm (GA)and Particle Swarm Optimization (PSO) for Artificial Neural Network (ANN) to improve the estimation of electricity demand of the state of Tamil Nadu in India. The GA-PSO model optimizes the coefficients of factors of gross state domestic product (GSDP) , electricity consumption per capita, income growth rate and consumer price index (CPI) that affect the electricity demand. Based on historical data of 25 years from 1991 till 2015, the simulation results of GA-PSO models are having greater accuracy and reliability than single optimization methods based on either PSO or GA. The forecasting results of ANN-GA-PSO are better than models based on single optimization such as ANN-BP, ANN-GA, ANN-PSO models. Further the paper also forecasts the electricity demand of Tamil Nadu based on two scenarios. First scenario is the “as-it-is” scenario, the second scenario is based on milestones set for achieving goals of “Vision 2023” document for the state. The present research also explores the causality between the economic growth and electricity demand in case of Tamil Nadu. The research indicates that a direct causality exists between GSDP and the electricity demand of the state.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

Collision avoidance is an important feature in advanced driver-assistance systems, aiming at providing correct, timely and reliable warnings before an imminent collision (objects, vehicles, pedestrians, etc.). A co-simulation framework is proposed in this paper to address the design and evaluation of collision avoidances in a cyber-physical system. The co-simulation framework is supported on the interaction between SCANeR and Matlab/Simulink. From the best of authors’ knowledge, two main contributions are reported in this paper. Firstly, the modelling and simulation of virtual on-chip LIDAR sensors in a cyber-physical system (CPS) considering traffic scenarios is presented. The CPS is designed and implemented in SCANeR. Secondly, an obstacle recognition library with three specific Artificial Intelligence-based methods is also designed based on sensory information database provided by SCANeR. Three methods for collision avoidance detection are considered, i.e.; a multi-layer perceptron neural network, a self-organization map and a support vector machine. Finally, a comparison among these methods for detecting obstacles before different weather conditions is done with very promising results in terms of accuracy. The best results are achieved using the multi-layer perceptron in sunny and fog conditions, the support vector machine in rainy and self-organized map in snowy conditions.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

Blazars show rapid and high amplitude variability. In this work , Fermi daily light curve of 130 sources are analyzed, distribution of daily variability are compared with each other by using Kolmogorov-Smirnov (K-S) test. results show: 1)Some pairs of the distributions are similar; 2) In most cases, the distributions are not Gaussian.

Recently, there has been a growing interest in the production of electricity from renewable energy sources (RES). The RES investment is characterized by uncertainty, which is long-term, costly, depend on feed-in-tariff and support schemes. In this paper, we address the real option valuation (ROV) of a solar power plant investment. The real option framework is investigated. This framework considers the renewable certificate price, furthermore the cost of delay between establishing and operating the solar power plant. The optimal time of launching the project and assess the value of deferred option are discussed. The new three stage numerical methods are constructed, the Lobatto3C-Milstein (L3CM) methods. The numerical methods are integrated with concept of Black-Scholes option pricing theory, and applied in option valuation for solar energy investment with uncertainty. The numerical results of L3CM, finite difference and Monte Carlo methods are compared to show the efficiency of our methods. Our data set refers to the Arab Republic of Egypt.

It is a common practice to detect outliers in a financial time series in order to avoid the adverse effect of additive outliers. This paper investigated the performance of GARCH family models (sGARCH; gjrGARCH; iGARCH; TGARCH and NGARCH) in the presence of different sizes of outliers (small, medium and large) for different time series lengths (250, 500, 750, 1000, 1250 and 1500) using root mean square error (RMSE) and mean absolute error (MAE) to adjudge the models. In a simulation iteration of 1000 times in R environment using rugarch package, results revealed that for small size of outliers, irrespective of the length of time series, iGARCH dominated, for medium size of outliers, it was sGARCH and gjrGARCH that dominated irrespective of time series length, while for large size of outliers, irrespective of time series length, gjrGARCH dominated. The study further leveled that in the presence of additive outliers on time series analysis, both RMSE and MAE increased as the time series length increased.

As with many of the non-deterministic search algorithms, particularly those are analogous to complex biological systems, there are a number of inherent difficulties, and the Bees Algorithm (BA) is no exception. Basic versions and variations of the BA have their own drawbacks. Some of these drawbacks are a large number of parameters to be set, lack of methodology for parameter setting and computational complexity. This paper describes a Grouped version of the Bees Algorithm (GBA) addressing these issues. Unlike its conventional version, in this algorithm bees are grouped to search different sites with different neighbourhood sizes rather than just discovering two types of sites, namely elite and selected. Following a description of the GBA, the results gained for 12 benchmark functions are presented and compared with those of the basic BA, enhanced BA, standard BA and modified BA to demonstrate the efficacy of the proposed algorithm. Compared to the conventional implementations of the BA, the proposed version requires setting of fewer parameters, while producing the optimum solutions much faster.

Titanium’s accelerating usage in global markets is attributable to its distinctive combination of physical and metallurgical properties. The key to best utilizing titanium is to exploit these characteristics, especially as they complement one another in a given application, rather than to just directly substitute titanium for another metal. Titanium alloy are extensively used in aerospace applications such as components in aero-engines and space shuttles, mainly due to their superior strength to weight ratio. For these demanding applications functionality and reliability of components are of great importance. To increase flight safety, higher sensitivity inspections are sought for rotating parts. Increased sensitivity can be applied at the billet stage, the forging stage, or both. Inspection of the forging geometry affords the opportunity to apply the highest sensitivity due to the shorter material paths when compared to those required for billet inspections. Forging inspection is typically performed for titanium (Ti) rotating parts with immersion inspection and fixed-focus, single-element transducers. Increased gain is required with depth because the ultrasonic beam attenuates with distance and diverges beyond the focus position that is placed near the surface. The higher gain that is applied with depth has the effect of increasing the UT noise with depth. The relationships between the UT noise, selection of the examination technique and the smallest detectable defect are presented in this material.

The optimization of guide vane closing schemes (OGVCS) of pumped storage hydro unit (PSHU) is the research field of cooperative control and optimal operation of pumped storage, wind power and solar power generation. This paper presents a OGVCS model of PSHU considering the rise rate of the unit rotational speed and the specific node pressure of each hydraulic unit, as well as various complicated hydraulic and mechanical constraints. OGVCS model is formulated as a multi-objective optimization problem to optimize conflictive objectives, i.e., unit rotational speed and water hammer pressure criteria. In order to realize the efficient solution of the OGVCS model, an enhanced multi-objective bacterial-foraging chemotaxis gravitational search algorithm (EMOBCGSA) is proposed to solve this problem, which adopts population reconstruction, adaptive selection chemotaxis operator of local searching strategy and Elite archive set to efficiently solve the multi-objective problem. Especially, novel constraints-handling strategy with eliminating and local search based on violation ranking is used to balance various hydraulic and mechanical constraints. Finally, simulation cases of complex extreme operating conditions (i.e., load rejection and pump outage) of ‘single tube-double units’ type PSHU system are conducted to verify the feasibility and effectiveness of the proposed EMOBCGSA in solving OGVCS problem. The simulation results indicate that the proposed EMOBCGSA can provide lower rise rate of the unit rotational speed and smaller water hammer pressure than other method established recently while considering various complex constraints in OGVCS problem.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

Facial expression has lots of applications in human-computer interaction. Although feature extraction and selection have been well studied, the specificity of each expression variation is not fully explored in state-of-the-art works. In this work, the problem of multiclass expression recognition is converted into triplet-wise expression recognition. For each expression triplet, a new feature optimization model based on Action Unit (AU) weighting and patch weight optimization is proposed to represent the specificity of the expression triplet. Sparse representation based approach is then proposed to detect the active AUs of testing sample for better generalization. The algorithm achieved competitive accuracies of 89.67% and 94.09% for Jaffe and CK+ databases, respectively. Better cross-database performance has also been observed.

Continuation methods are presented that are capable of treating frequency-domain flutter equations including multiple nonlinearities represented by describing functions. A small problem demonstrates how a series of continuation processes can find all limit-cycle oscillations within a specified region with a reasonable degree of confidence. Curves of the limit-cycle amplitude variation with velocity, indicating regions of stability and instability with colors give a compact view of the nonlinear behavior throughout the flight regime. A continuation technique for reducing limit-cycle amplitudes by adjusting various system parameters is presented. These processes are economical enough to be a routine part of aircraft design and certification.

Patch antennas are compact, less complex, planar structures and therefore, widely used in small satellite missions for telecommand, data link, and intersatellite link, particularly in S- band and X- band. Improved performance of these patch antennas in terms of gain and compactness will di-rectly affect the communication efficiency of small satellite missions. Especially the coming IoT (Internet of Things) constellations require high gain and efficient antenna arrays. An optimization of single patch antenna elements is an important cornerstone for the missions. Therefore, the ef-fects of various antenna enhancement techniques, such as slotted ground plane, resistor and ca-pacitor integration, parasitic patch elements, are analyzed. These techniques were applied on a rectangular patch antenna with parameter variation to identify the optimal performances with respect to bandwidth, operating frequency, gain, polarization, and power flow. Finally, the techniques were combined to obtain an optimized antenna in terms of gain and compactness. The results were compared to a slotted reference antenna. For the scenario of a 2.4 GHz patch antenna, a gain optimization of 27 % (from 7.09 to 8.14 dBi) or size reduction of 52 % (from 96.04 to 46.2 cm²) could be achieved. Overall, our study revealed an effective way to increase the patch antenna performance, which can directly contribute to more efficient communication links and design of antenna arrays.

In recent years, new metaheuristic algorithms have been developed taking as reference the inspiration on biological and natural phenomena. This nature-inspired approach for algorithm development has been widely used by many researchers in solving optimization problem. These algorithms have been compared with the traditional ones algorithms and have demonstrated to be superior in complex problems. This paper attempts to describe the algorithms based on nature, that are used in fuzzy clustering. We briefly describe the optimization methods, the most cited nature-inspired algorithms published in recent years, authors, networks and relationship of the works, etc. We believe the paper can serve as a basis for analysis of the new are of nature and bio-inspired optimization of fuzzy clustering.

In this work we study the energy consumption by various modern secured hash functions (MD2, MD5, SHA-1, and SHA-2) and modern symmetric key encryption protocols (Blowfish, DES, 3DES, and AES) from the algorithmic perspective. We identify various parameters that moderate energy consumption of these hashes and protocols. Our work is directed towards redesigning or modifying these algorithms to make them consume lesser energy. As a first step, we try to determine the applicability of the asymptotic energy complexity model by Roy et. al. on these hashes and protocols. Specifically, we try to observe whether parallelizing the access of blocks of data in these algorithms reduces their energy consumption based on the energy model. Our results confirm the applicability of the energy model on these hashes and protocols. Our work is motivated by the relevance and importance of cryptographic hashes and symmetric key protocols for modern ICT (Information and Communication Technology), and ICT enabled industry to keep them protected from dynamically changing threat scenarios. Hence the design of more energy efficient hashes and protocols will definitely contribute in reducing the ICT energy consumption that is continuously increasing.

This paper deals with the problem of real-time management of Smart Grids. For this sake, the energy management is integrated with the power system through a telecommunication system. The use of Multiagent Systems leads the proposed algorithm to find the best-integrated solution, taking into consideration the operating scenario and the system characteristics. The proposed technique is tested with the help of an academic microgrid, so the results may be replicated.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Forming a clustered network structure has been proposed as a solution to increase network performance, scalability, stability and manageability in an ad hoc network. A good clustering algorithm aims to select cluster heads among available nodes so that a number of specific constraints are satisfied; thus the cluster head selection problem is a multiobjective optimization problem. This paper proposes an algorithm on the basis of ant colony optimization (ACO) to be used to solve this problem. The proposed algorithm is a simple, one hop cluster formation algorithm, to form a clustered structure with the minimum number of clusters. The centralized ACO-based clustering algorithm is evaluated and compared with other clustering algorithms in ad hoc networks in terms of cluster density.

Trajectory Optimization (TO) is the sequence of processes that are considered in order to produce the best path that mends the overall performance or reduces the consumption of the resources where the restriction system remains maintained. In this survey, an inclusive review of the latest advancements in modeling and optimization of trajectory generation in robotic applications will be discussed broadly. In recent times, numerous studies have employed optimal control techniques involving direct and indirect methods in order to convert the authentic Trajectory Optimization problem into a constrained parameter optimization problem. Moreover, a huge variety of optimization algorithms such as Genetic Algorithms (GA), Simulated Annealing (SA), Sequential Quadratic Programming (SQP), and Particle Swarm Optimization (PSO) are used aiming to find the optimal solutions for trajectory planning. It is observable that, minimizing the jerk, energy consumption, and execution time among the most widely used design objectives, on the other hand, the robot’s joints configurations and the motor torques are the most used design variables. This paper aims to review the fundamental techniques and their coincident robotic applications in the field of trajectory optimization aiming to afford some steering for related researchers.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

The paper presents the design and the implementation of different advanced control strategies that are applied to a nonlinear model of a thermal unit. A data–driven grey–box identification approach provided the physically meaningful nonlinear continuous–time model, which represents the benchmark exploited in this work. The control problem of this thermal unit is important since it constitutes the key element of passive air conditioning systems. The advanced control schemes analysed in this paper are used to regulate the outflow air temperature of the thermal unit by exploiting the inflow air speed, whilst the inflow air temperature is considered as an external disturbance. The reliability and robustness issues of the suggested control methodologies are verified with a Monte–Carlo analysis for simulating modelling uncertainty, disturbance and measurement errors. The achieved results serve to demonstrate the effectiveness and the viable application the suggested control solutions to air conditioning systems. The benchmark model represents one of the key issues of this study, which is exploited for benchmarking different model–based and data–driven advanced control methodologies through extensive simulations. Moreover, this work highlights the main features of the proposed control schemes, while providing practitioners and heating, ventilating and air conditioning engineers with tools to design robust control strategies for air conditioning systems.

This paper examines the correlation between numbers of computer cores in parallel genetic algorithms. The objective to determine the linear polynomial complementary equation in order represent the relation between number of parallel processing and optimum solutions. Model this relation as optimization function (f(x)) which able to produce many simulation results. F(x) performance is outperform genetic algorithms. Compression results between genetic algorithm and optimization function is done. Also the optimization function give model to speed up genetic algorithm. Optimization function is a complementary transformation which maps a TSP given to linear without changing the roots of the polynomials.

An empirical model is presented for estimating discharge on the Ubombo Sugar Limited (USL) main gravity canal to enhance bulk water management and water use efficiency. It uses stage readings obtained from measuring flumes A, B, C, and UPS to simulate discharge. The rationale for the development of the mathematical flow simulation model is the significance of the UPS flume as it measures readings that influence the daily operations of the farm, and the experiences with the ultrasonic flow meter installed in the flume. The model also provides a first for the simulation of accurate flow rates for flumes A, B, and C. A spreadsheet program that enables express prediction of canal flow rates was developed to influence timely implementation of these water management decisions. Calibrations demonstrated that the model is capable of predicting discharge at high accuracy (p>95%), and can be reliably used as a decision support tool for bulk water management. It can also be expanded to include other water measuring structures along Canal 1 and Canal 2, as well as the development of a stand-alone water management application for desktop and mobile computers.

The total enthalpies of the 16 different spin configurations that can be realized in the unit cell of the archetype spin crossover complex [Fe(phen)₂(NCS)₂] (phen=1,2-phenanthroline) were calculated applying periodic density functional theory combined with the Hubbard model and the Grimme-D2 dispersion correction (DFT+U/D2). The obtained enthalpy differences between the individual spin configurations were used to determine spin couplings of an Ising-like model and subsequent Monte Carlo simulations for this model allowed to estimate the phenomenological interaction parameter Г of the Slichter-Drickamer model, which is commonly used to describe the cooperativity of the spin transition. The calculational procedure described here, which led to an estimate of about 3 kJ/mol⁻¹ for Г, in good agreement with experiment, may be used to predict from first principles how modifications of spin crossover complexes can change the character of the spin transition from gradual to abrupt and vice versa.

Project logistics is one of the specific logistics operations. Compared to other logistics operations, it needs more efficient planning and engineering applications in each operational process. On the other hand, each project logistics operation can be defined as tailor-made operations, since it has no similarity with other operations. Consequently, each project logistics operation should be planned and carried out according to its own conditions and parameters. This study focuses on the simulation of project logistics operations under the light of computerized applications from start to finish of the logistics operation. In this study, transportation operations of 600 tons of autoclave from the Petkim port to the Gördes building site were selected as a case study.

Coronavirus disease 2019 (COVID-19) is an emerging infectious disease that was first reported in Wuhan, China and has subsequently spread worldwide. In the absence of any antiviral or immunomodulatory therapies, the disease is spreading at an alarming rate. 5 to 10% of recovered patients in Wuhan test positive again; this suggest that for controlling COVID-19, vaccines may be better option than drugs. A clinical trial to evaluate an anti-COVID-19 vaccine has started recently. However, its efficacy and potency have to be evaluated and validated. As an alternative, we are presenting a first-of-its-kind, designed multi-peptide subunit based epitope vaccine against COVID-19. The vaccine construct comprise an adjuvant, CTL, HTL, and B-cell epitopes joined by linkers. The vaccine is non-toxic, non-allergenic, thermostable and immunogenic with the capability to elicit a humoral and cell-mediated immune response. The findings are validated with high-end computation-based methods. This unique vaccine is made up of 33 highly antigenic epitopes from three proteins that have a prominent role in host receptor recognition, viral entry, and pathogenicity. We advocate this vaccine must be synthesized and tested urgently as public health priority.

Considering the need to reduce greenhouse gas emissions, onshore wind energy is certain to play a major role in future energy systems. This topic has received significant attention from the research community, producing many estimations of Europe's onshore wind potential for capacity and generation. Despite this focus, previous estimates have relied on distribution assumptions and simulation schemes that summarily under predict both the amount of available future wind capacity as well as its performance. Foremost in this regard is the common use of contemporary, or at least near-future, turbine designs which are not fitting for a far-future context. To fulfill this role, an improved, transparent, and fully reproducible work flow is presented for determining European onshore wind potential. Within a scenario of turbine cost and design in 2050, 13.5 TWof capacity is found to be available, allowing for 34.4 PWh of generation. By sorting the explicitly-placed potential generation locations by their expected generation cost, national relations between turbine cost and performance versus a desired capacity are exposed. In this way, it is shown that all countries possess some potential for onshore wind energy generation below 4 €_ct kWh^-1. and, furthermore, that it is unlikely for these costs to exceed 6 €_ct kWh^-1.

There are numerous approaches to model an influence of manufacturing parameters on the dissolution and disintegration of solid dosage forms. A modern approach for modelling and simulating complex and heterogeneous systems such as pharmaceutical tablets focuses on computationally-intensive finite-element or discreet element methods. Industrial challenges such as Process Analytical Technology (PAT) and Quality by Design are stimulating computer-based technologies to design, control and improve the quality of pharmaceutical compacts and their performance. In this study the disintegration and dissolution model based on the numerical solutions of the Noyes-Whitney equation and cellular automata supported disintegration model are proposed and evaluated. The results from in vitro release studies of the mefenamic acid formulations were compared to the calculated release patterns from the tablet structures obtained from microtomography experiments and the purely algorithmically created virtual tablets.

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

Particle Swarm Optimization (PSO) is a metaheuristic global optimization paradigm that has gained prominence in the last two decades due to its ease of application in unsupervised, complex multidimensional problems which cannot be solved using traditional deterministic algorithms. The canonical particle swarm optimizer is based on the flocking behavior and social co-operation of birds and fish schools and draws heavily from the evolutionary behavior of these organisms. This paper serves to provide a thorough survey of the PSO algorithm with special emphasis on the development, deployment and improvements of its most basic as well as some of the very recent state–of-the-art implementations. Concepts and directions on choosing the inertia weight, constriction factor, cognition and social weights and perspectives on convergence, parallelization, elitism, niching and discrete optimization as well as neighborhood topologies are outlined. Hybridization attempts with other evolutionary and swarm paradigms in selected applications are covered and an up-to-date review is put forward for the interested reader.

Highly flexible manufacturing systems require continuous run-time (self-) optimization of processes with respect to various parameters, e.g. efficiency, availability, energy consumption etc. A promising approach for achieving (self-) optimization in manufacturing systems is the usage of the context sensitivity approach. Thereby the Cyber-Physical Systems play an important role as sources of information to achieve context sensitivity. In this paper it is demonstrated how context sensitivity can be used to realize a holistic solution for (self-) optimization of discrete flexible manufacturing systems, by making use of Cyber-Physical System integrated in manufacturing systems/processes. A generic approach for context sensitivity, based on self-learning algorithms, is proposed aiming at a various manufacturing systems. The new solution is propos encompassing run-time context extractor and optimizer. Based on the self-learning module both context extraction and optimizer are continuously learning and improving their performance. The solution is following Service Oriented Architecture principles. The generic solution is developed and then applied to two very different manufacturing processes. This paper proposes a holistic solution to achieve context sensitivity for Flexible Manufacturing Systems, whereby the knowledge created by applying the context sensitivity approach can be used for (self-) optimization of manufacturing processes.

The integration of automation and process optimization within the context of AI-powered digital transformation has emerged as a pivotal strategy for organizations aiming to enhance efficiency, foster innovation, and competitiveness. This paper is devoted to present innovative contribution by providing a comprehensive structured roadmap that outlines the foundational principles necessary for the successful integration of automation and optimizing processes within the con-text of emerging AI technologies. The paper introduce a cohesive framework consisting of es-sential key pillars: Data-Driven Insights, Seamless Automation, Adaptive Learning and Contin-uous Improvement, Human-Centric Collaboration, Ethical and Responsible AI, Strategic Align-ment, Scalability, and Innovation. These pillars function as guiding principles to navigate the in-tricate landscape of automation-driven initiatives within AI-powered digital transformation. By embracing these pillars, organizations can embark on a transformative journey that maximizes the potential of automation, fosters innovation, and positions them as leaders in the ever-evolving landscape of AI-driven business operations.

Recent advances in sensor and platform technologies such as satellite systems, unmanned aerial vehicles (UAV), manned aerial platforms, and ground-based sensor networks have resulted in massive volumes of data is produced and collected about the earth. Processing, managing, and analyzing these data is one of the main challenges in 3D synthetic representation used in modeling and simulation (M&S) of the natural environment. M&S devices, such as flight simulators, traditionally require a variety of different databases to provide a synthetic representation of the world. M&S often requires integration of data from a variety of sources stored in different formats. Thus, for simulation of a complex synthetic environment, such as a 3D terrain model, tackling interoperability among its components (geospatial data, natural and man-made objects, dynamic and static models) is a critical challenge. Conventional approaches used local proprietary data models and formats. These approaches often lacked interoperability and created silos of content within the simulation community. Therefore, open geospatial standards are increasingly perceived as a means to promote interoperability and reusability for 3D M&S. In this paper, the Open Geospatial Consortium (OGC) CDB Standard is introduced. “CDB” originally refers to Common DataBase which is currently considered as a name with no abbreviation in the OGC community. The OGC CDB is an international standard for structuring, modeling, and storing geospatial information required in high performance modeling and simulation applications. CDB defines the core conceptual models, use cases, requirements, and specifications for employing geospatial data in 3D M&S. The main features of the OGC CDB Standard are described as run-time performance, full plug-and-play interoperable geospatial data store, usefulness in 3D and dynamic simulation environment, ability to integrate proprietary and open-source data formats. Furthermore, compatibility with the OGC standards baseline reduces the complexity of discovering, transforming, and streaming geospatial data into the synthetic environment and makes them more widely acceptable to major geospatial data/software producers. This paper includes an overview of OGC CDB version 1.0 which defines a conceptual model and file structure for the storage, access, and modification of a multi-resolution 3D synthetic environment data store. Finally, this paper presents a perspective of future versions of the OGC CDB and what the steps are for humanizing the OGC CDB standard with the other OGC/ISO standards baseline.

Lassa virus (LASV) is responsible for a type of acute viral haemorrhagic fever referred to as Lassa fever. Lack of adequate treatment and preventive measures against LASV resulted in a high mortality rate in its endemic regions. In this study, a multi-epitope vaccine was designed using immunoinformatics as a prophylactic agent against the virus. Following a rigorous assessment, the vaccine was built using T-cell (N_CTL=8 and N_HTL=6) and B-cell (N_LBL=4) epitopes from each LASV-derived protein with suitable linkers and adjuvant. The physicochemistry, immunogenic potency and safeness of the designed vaccine (~68 kDa) were assessed. In addition, chosen CTL and HTL epitopes of our vaccine showed 97.37% worldwide population coverage. Besides, disulphide engineering also improved the stability of the chimeric vaccine. Molecular docking of our vaccine protein with toll-like receptor (TLR2) showed binding efficiency followed by dynamic simulation for stable interaction. Furthermore, higher levels of cell-mediated immunity and rapid antigen clearance were suggested by immune simulation and repeated-exposure simulation, respectively. Finally, the optimized codons were used in in silico cloning to ensure higher expression within E. coli K12 bacterium. With further assessment both in vitro and in vivo, we believe that our proposed peptide-vaccine would be potential immunogen against Lassa fever.

The use of unmanned aerial vehicle (UAV) during emergency response of a disaster has been widespread in recent years and the terrain images captured by the cameras on board these vehicles are significant sources of information for such disaster monitoring operations. Thus, analyzing such images are important for assessing the terrain of interest during such emergency response operations. Further, these UAVs are mainly used in disaster monitoring systems for the automated deployment of sensor nodes in real time. Therefore, deploying and localizing the wireless sensor nodes optimally, only in the regions of interest that are identified by segmenting the images captured by UAVs, hold paramount significance thereby effecting their performance. In this paper, the highly effective nature-inspired Plant Growth Simulation Algorithm (PGSA) has been applied for the segmentation of such terrestrial images and also for the localization of the deployed sensor nodes. The problem is formulated as a multi-dimensional optimization problem and PGSA has been used to solve it. Furthermore, the proposed method has been compared to other existing evolutionary methods and simulation results show that PGSA gives better performance with respect to both speed and accuracy unlike other techniques in literature.

This research demonstrates the optimization and production of biochar from barley husk (BH), corn cob (CC), and Agave salmiana leaves (AL) via pyrolysis in a muffle furnace. Taguchi experimental design (L9) was applied to conduct the experiments at different levels by altering four operating parameters. Carbonization temperature (300–500 ºC), carbonization time (30–90 min), precursor mass (2–5 g) and N₂ flow rate (100–200 cc/min) were the variables examined in this study. The effect of the parameters on the biochar yield was investigated, and the important parameters were identified employing analysis of variance (ANOVA). The optimum conditions for maximum biochar yield were: carbonization temperature of 400 ºC, carbonization time of 30 min, precursor mass of 2 g, and N₂ flow rate of 150 cc/min. The biochars produced under optimum conditions was characterized physically and chemically. Biochar yields of 19.75% for corn cob (CCB), 32.88% for barley husk (BHB), and 31.14% for agave leaves (ALB) were obtained.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

Nature-inspired algorithms are very popular tools for solving optimization problems inspired by nature. However, there is no guarantee that optimal solution can be obtained using a randomly selected algorithm. As such, the problem can be addressed using trial and error via the use of different optimization algorithms. Therefore, the proposed study in this paper analyzes the time-complexity and efficacy of some nature-inspired algorithms which includes Artificial Bee Colony, Bat Algorithm and Particle Swarm Optimization. For each algorithm used, experiments were conducted several times with iterations and comparative analysis was made. The result obtained shows that Artificial Bee Colony outperformed other algorithms in terms of the quality of the solution, Particle Swarm Optimization is time efficient while Artificial Bee Colony yield a worst case scenario in terms of time complexity.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for 15-5PH Stainless steel by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as concentration of cutting fluid , temperature of cutting fluid , feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error and material removal rate, the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, concentration of cutting fluid, radial depth of cut and temperature of cutting fluid. Finally, confirmation tests were carried out to make a comparison between the experimental results and developed model. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

Today, Colebrook’s equation is mostly accepted as an informal standard for modeling of turbulent flow in hydraulically smooth and rough pipes including transient zone in between. The empirical Colebrook’s equation relates the unknown flow friction factor (λ) with the known Reynolds number (R) and the known relative roughness of inner pipe surface (ε/D). It is implicit in unknown friction factor (λ). Implicit Colebrook’s equation cannot be rearranged to derive friction factor (λ) directly and therefore it can be solved only iteratively [λ=f(λ, R, ε/D)] or using its explicit approximations [λ≈f(R, ε/D)]. Of course, approximations carry in certain error compared with the iterative solution where the highest level of accuracy can be reached after enough number of iterations. The explicit approximations give a relatively good prediction of the friction factor (λ) and can reproduce accurately Colebrook’s equation and its Moody’s plot. Usually, more complex models of approximations are more accurate and vice versa. In this paper, numerical values of parameters in various existing approximations are changed (optimized) using genetic algorithms to reduce maximal relative error. After this improvement computational burden stays unchanged while accuracy of approximations increases in some of the cases very significantly.

The next future using machine tools will be dominated by highly flexible and interconnected systems, in order to achieve the required productivity, accuracy and reliability. Nowadays, distortion and vibration problems are easily solved for the most common cases by sing models based on equations describing the physical laws dominating the machining process; however additional efforts are needed to overcome the gap between scientific research and the real manufacturing problems. In fact, there is an increasing interest in developing simulation packages based on “deep knowledge and models” that aid the machine designer, the production engineer, or machinists to get the best of their machines. This article proposes a systematic methodology to reduce problems in machining by means of a simulation utility, which recognizes, collects and uses the main variables of the system/process as input data, and generates objective results that help in the proper decision-making. Direct benefits by such an application are found in a) the fixture/clamping optimal design, b) the machine tool configuration, c) the definition of chatter free optimum cutting conditions and the right programming of cutting tool path at the Computer Aided Manufacturing (CAM) stage. The information and knowledge-based approach showed successful results in several local manufacturing companies.

This paper proposes a Mixed Integer Conic Programming (MICP) model for community microgrids considering the network operational constraints and building thermal dynamics. The proposed multi-objective optimization model optimizes not only the operating cost, including fuel cost, purchasing cost, battery degradation cost, voluntary load shedding cost and the cost associated with customer discomfort due to room temperature deviation from the set point, but also several performance indices, including voltage deviation, network power loss and power factor at the Point of Common Coupling (PCC). In particular, the detailed thermal dynamic model of buildings is integrated into the distribution optimal power flow (D-OPF) model for the optimal operation. The heating, ventilation and air-conditioning (HVAC) systems can be scheduled intelligently to reduce the electricity cost while maintaining the indoor temperature in the comfort range set by customers. Numerical simulation results show the effectiveness of the proposed model and significant savings in electricity cost with network operational constraints satisfied.

Single cell proteins are the dead dried cells of microorganisms or purified protein isolated from microorganism’s cell culture, used as a food supplement to humans’ food and animals feed. World suffer from malnutrition particularly developing countries, due to rapid increase in population, increased the demand for protein and nutrients requirement. Bacteria is potential microorganism for SCP production due to high protein content, fast generation time, bio-active secondary metabolites production and can grow on various substrates. Actinobacteria species and strain have capability to produce biological active compounds, produced about two-thirds of antibiotics available in the market, actively used as antibiotics, antiprotozoal, antifungal, antiviral, anticancer, anticholesterol, antihelminth and immunosuppressant. Actinomycetes can be used as probiotic as well as single cell protein that will deal with antibiotic as well as protein source.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

Arylamine N-acetyltransferases (NATs) are cytosolic enzymes, highly polymorphic, present in both eukaryotes and prokaryotes. These enzymes play an important role in the detoxification and activation of xenobiotics as well as in the synthesis of endogenous compounds. Specific NATs have been pointed out in the literature as possible therapeutic targets. In particular, the human NAT1, for the treatment of certain cancers, and the NAT from M. tuberculosis (TBNAT), for the treatment of tuberculosis. This paper describes an in silico approach to prospect and select potentially inhibitors of NAT1 and TBNAT from the Traditional Chinese Medicine (TCM) using free available tools. A library with ligands from TCM was previously screened in order to select only compounds with optimal pharmacological properties. The affinity of the selected ligands with respect to NAT enzymes was then evaluated by virtual screening (VS). Subsequently, the complexes with the best ligands were submitted to molecular dynamics (MD) simulations aiming to obtain better quality information on affinity and selectivity. The results for one specific ligand, ZINC14690579, indicated its potential for affinity and selectivity. ZINC14690579 structure may represent the discovery of a new scaffold for future development of NAT inhibitors.

X-ray fluorescence is largely employed in the measurement of the thickness of coatings. Despite of its diffusion, the task is not straightforward because of the complex physics involved that results in high dependence on matrix effects. Thickness quantification is in practice accomplished using the Fundamental Parameters approach, adjusted with empirical measurements of standards with known composition and thickness. This approach has two major drawbacks: i) there are no standards for any possible coating and coating architecture and ii) even relying on standards, the quantification of unknown samples requires the precise knowledge of the matrix nature (e.g., in case of multilayer coatings the thickness and the composition of each underlayer). In this work, we describe a semiquantitative approach to coatings thickness measurement based on the construction of calibration curves through simulated XRF spectra built with Monte Carlo simulations. Simulations have been performed with the freeware software XMI-MSIM. We have assessed the accuracy of the methods by comparing the results with those obtained by i) XRF thickness determination with standards and ii) FIB-SEM cross-sectioning. Then we evaluated which parameters are critical in this kind of indirect thickness measurements.

In this work, we examined the effect of tropospheric emissions on tropospheric ozone (O₃) by conducting three-dimensional (3D) chemistry transport model (CTM) simulations. For the control run, the CTM model simulates tropospheric O₃ levels with a complete set of anthropogenic, biomass burning, and vegetation emissions [8]. For the no-emission simulation, all anthropogenic, biomass burning, and vegetation emissions were turned off. Comparisons of results from these two simulations exhibit the emission impacts on the tropospheric O₃. In the no-emission simulation, distinctive low surface O₃ with concentrations less than 5 ppbv prevail over the Amazon basin, tropical South America, tropical South Africa, Southeast Asia. Transport of air from these land areas downwind contributes to the low O₃ over the remote marine boundary layer. In contrast, elevated O₃ levels over the extra-tropical remote marine boundary layer are less supported by the anthropogenic and biomass burning emissions but more sustained by the downward transport of O₃ from the stratosphere. These results demonstrate that the northern hemisphere continental areas (north of 30^◦N ), polar regions, and tropical continental regions are more sensitive to the tropospheric emissions. The northern hemisphere winter is mostly dominated by the stratospheric processes, while the tropospheric emissions dominate over the southern hemisphere tropical continental areas from tropics to 30^◦S latitudinal bands. The northern hemisphere continental regions are increasingly dominated by tropospheric emissions from spring, to reach maxima in summer, and started to reduce in autumn months.

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

Background: COVID-19, caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is a global pandemic affecting approximately 490,000 people and accounting for more than 22,000 deaths and has no generally acceptable cure. Here, the recently resolved 3D structure of SARS-CoV-2 receptor binding domain (RBD) in complex with its receptor-the angiotensin converting enzyme-2 (ACE-2) have provided the basis for screening chemical database for novel entry inhibitors. Methods: Molecular docking protocols have been used to rapidly screen FDA database for high affinity interaction at the SARS-CoV-2-RBD/ACE-2 interface. One of the top candidates, ubrogepant has been selected and further studied using atomistic molecular dynamics simulation method. Results: Molecular docking result showed that ubrogepant (UBR) and darunavir have binding energies of -10.4 kcal/mol. MMPBSA free energy analyses of UBR bound to RBD, ACE-2 and RBD/ACE-2 revealed RBD/ACE-2 > ACE-2 > RBD preference. Network analysis showed that interaction captured in the crystal structure were disrupted in UBR-bound state, hydration of the interface and increased atomic fluctuation within the RBD oligomerization interface and ACE-2 zinc binding site. Conclusions: The ability of ubrogepant to rupture the interaction at the RBD/ACE-2 interface residues of SARS-CoV-2 RBD/ACE-2 complex may result in loss of protein function with direct implication on oligomerization formation in RBD and loss of function in ACE-2 thus, making binding, cellular receptor recognition impossible. General Significance: Ubrogepant represents a new therapeutic candidate in the fight against COVID-19, as it binds with relatively high affinity with free RBD, ACE-2 receptor and SARS-CoV-2 RBD/ACE-2 complex based on binding affinity calculations.

In this study, we repositioned thiopurine drugs used for the treatment of acute leukaemia as new tyrosinase inhibitors. Tyrosinase catalyses two distinct and successive oxidations in melanin biosynthesis: the conversions of tyrosine to dihydroxyphenylalanine (DOPA) and DOPA to dopaquinone. Continuous efforts are underway to discover small molecule inhibitors of tyrosinase for therapeutic, cosmetic, and agricultural purposes. Structure-based virtual screening has predicted inhibitor candidates for mushroom tyrosinase from drugs approved by the US Food and Drug Administration (FDA). Enzyme assays have confirmed the thiopurine leukaemia drug, thioguanine, as a tyrosinase inhibitor. Two other thiopurine drugs, mercaptopurine and azathioprine, were also evaluated for their tyrosinase inhibitory activity; mercaptopurine caused stronger inhibition than thioguanine did, whereas azathioprine was a poor inhibitor. The inhibitory constants of thioguanine and mercaptopurine were calculated as 52 and 16 µM, respectively, and the value of mercaptopurine was comparable to that of the well-known inhibitor kojic acid (13 µM). The cell lysate and melanin content assay in B16F10 melanoma cells confirmed that the compounds inhibited mammalian tyrosinase. In particular, 50 µM thioguanine reduced the melanin content by 57% without cytotoxicity. Furthermore, the thiopurine drugs shared little chemical similarity with the known tyrosinase inhibitors.

The heavy demand of water resources from the Zarqa River Basin (ZRB) has resulted in a base-flow reduction of the River from 5m³/s to less than 1m³/s. This paper aims at predicting Curve Numbers (CN) as a baseline scenario and proposing restoration scenarios for ZRB. The method includes classifying the soil type and land use, predicting CNs, and proposing CN restoration scenarios. Prediction of existing CNs will be in parallel with the runoff prediction using the US Army Corps of Engineers HEC-1 Model, and Rainfall-Runoff Model (RRM). The models have been set up at the land use distribution of 0.3% water body, 9.3% forest and orchard, 71% mixture of grass, weeds, and desert shrubs, 7.0% crops, 4.0% urban areas, and 8.4% bare soil. The results show that CN under dry condition are 59, 78 under a normal condition and 89 under a wet condition. During vegetation period, CN are 52, 72 and 86 for the dry, normal and wet condition respectively. The restoration scenarios; CN decreases runoff, and increases soil moisture when using the contours, terraces and crop residues. Analyzing results of CN scenarios will be a fundamental tool to support end-users related to their targets to achieve watershed restoration.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

In this study, the efficiency of an anaerobic treatment system for wastewater from a South African poultry slaughterhouse was evaluated using a lab-scale static granular bed reactor (SGBR). The down-flow SGBR (2 L) was operated continuously for 138 days under mesophilic conditions (35-37 ˚C), at hydraulic retention times (HRTs) ranging from 24 to 96 h and average organic loading rates (OLRs) of 0.78 to 5.74 g COD/L.day. The SGBR achieved an average chemical oxygen demand (COD) removal efficiency of 80% and the maximum COD removal achieved was 95%, at an HRT of 24 h and average OLR of 5.74 g COD/L.day. The optimization of the SGBR, with regard to a suitable HRT and OLR, was determined using response surface methodology (RSM). The optimal SGBR performance with regard to the maximum COD removal efficiency was predicted for an OLR of 12.49 g COD/L.day and a HRT of 24 h, resulting in a 95.5% COD removal efficiency. The model R2 of 0.9638 indicated that the model is a good fit and is suitable to predict the COD removal efficiency for the SGBR.

The future of machine tools will be dominated by highly flexible and interconnected systems, in order to achieve the required productivity, accuracy and reliability. Nowadays, distortion and vibration problems are easily solved in labs for the most common machining operations by using models based on equations describing the physical laws of the machining processes; however additional efforts are needed to overcome the gap between scientific research and the real manufacturing problems. In fact, there is an increasing interest in developing simulation packages based on “deep-knowledge and models” that aid machine designers, production engineers or machinists to get the best of the machine-tools. This article proposes a methodology to reduce problems in machining by means of a simulation utility, which uses the main variables of the system&process as input data, and generates results that help in the proper decision-making and machining planification. Direct benefits can be found in a) the fixture/clamping optimal design, b) the machine tool configuration, c) the definition of chatter-free optimum cutting conditions and d) the right programming of cutting toolpaths at the Computer Aided Manufacturing (CAM) stage. The information and knowledge-based approach showed successful results in several local manufacturing companies and are explained in the paper.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Full-order state-space models represent the starting point for the development of advanced control methods for wind turbine systems (WTSs). Regarding existing control-oriented WTS models, two research gaps must be noted: (i) There exists no full-order WTS model in form of one overall ordinary differential equation that considers all dynamical effects which significantly influence the electrical power output; (ii) all existing reduced-order WTS models are subject to rather arbitrary simplifications and are not validated against a full-order model. Therefore, in this paper, two full-order nonlinear state-space models (of 11th and 9th-order in the (a, b, c)- and (d, q)-reference frame, resp.) for variable-speed variable-pitch permanent magnet synchronous generator WTSs are derived. The full-order models cover all relevant dynamical effects with significant impact on the system’s power output, including the switching behavior of the power electronic devices. Based on the full-order models, by a step-by-step model reduction procedure, two reduced-order WTS models are deduced: A non-switching (averaging) 7th-order WTS model and a non-switching 3rd-order WTS model. Comparative simulation results reveal that all models capture the dominant system dynamics properly. The full-order models allow for a detailed analysis covering the high frequency oscillations in the instantaneous power output due to the switching in the power converters. The reduced-order models provide a time-averaged instantaneous power output (which still correctly reflects the energy produced by the WTS) and come with a drastically reduced complexity making those models appropriate for large-scale power grid controller design.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

The application of thermoelectric generators (TEG) on the nozzle of an aviation jet engine was studied by finite element TEG-simulations. Against the background of system-level requirements of the reference aircraft this work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and fill factors (F) within the TE modules in order to maintain a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients at the nozzle surfaces this work reports the achievable power output. System-level requirement on the gravimetric power density (> 100 Wkg-1) can only be met for F ≤ 21%. Extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. Assessment of further potential is demonstrated by a parametric study on the fill factor, convective heat transfer coefficients, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient installation of TEG in consideration of the cost-specific power output of modern thermoelectric materials.