Drying food involves complex physical atmospheric mechanisms with non-linear relations from the air-food interactions and those relations are strongly dependent on the moisture contents and the type of food. Such dependence makes it complex to design suitable dryers dedicated to a single drying process. To streamline the design of a novel compact food-drying machine, a heat pump dryer component design optimization algorithm was developed as a subprogram of a Computer Aided Engineering tool. The algorithm requires inputting food and air properties, the volume of the drying container and the technical specifications of the heat-pump off-the shelf components. The heat required to dehumidify the food supplied by the heat exchange process from condenser to evaporator, and the compressor’s requirements (refrigerant mass flow rate and operating pressures) are then calculated. Compressors can then be selected based in the volume and type of food to be dried. The algorithm is shown via a flow chart to guide the user through 3 different stages: Changes in drying air properties, Heat flow within dryer and Product moisture content. Example results of how different compressors are selected for different type of produces and quantities (Agaricus Blazei mushroom with 3 different moisture contents or fish from Thunnini tribe) conclude this article.

This research demonstrates the optimization and production of biochar from barley husk (BH), corn cob (CC), and Agave salmiana leaves (AL) via pyrolysis in a muffle furnace. Taguchi experimental design (L9) was applied to conduct the experiments at different levels by altering four operating parameters. Carbonization temperature (300–500 ºC), carbonization time (30–90 min), precursor mass (2–5 g) and N₂ flow rate (100–200 cc/min) were the variables examined in this study. The effect of the parameters on the biochar yield was investigated, and the important parameters were identified employing analysis of variance (ANOVA). The optimum conditions for maximum biochar yield were: carbonization temperature of 400 ºC, carbonization time of 30 min, precursor mass of 2 g, and N₂ flow rate of 150 cc/min. The biochars produced under optimum conditions was characterized physically and chemically. Biochar yields of 19.75% for corn cob (CCB), 32.88% for barley husk (BHB), and 31.14% for agave leaves (ALB) were obtained.

In this manuscript, an automated framework dedicated to design space exploration and design optimization studies is presented. The framework integrates a set of numerical simulation, computer-aided design, numerical optimization, and data analytics tools using scripting capabilities. The tools used are open-source and freeware, and can be deployed on any platform. The main feature of the proposed methodology is the use of a cloud-based parametrical computer-aided design application, which allows the user to change any parametric variable defined in the solid model. We demonstrate the capabilities and flexibility of the framework using computational fluid dynamics applications; however, the same workflow can be used with any numerical simulation tool (e.g., a structural solver or a spread-sheet) that is able to interact via a command line interface or using scripting languages. We conduct design space exploration and design optimization studies using quantitative and qualitative metrics, and to reduce the high computing times and computational resources intrinsic to these kinds of studies, concurrent simulations and surrogate-based optimization are used.

Dump design and scheduling are critical elements to effective mine planning, especially if several of them are required in large-scale open pit mines. Infrastructure capital and transportation costs are considerable from an early stage in the mining project, and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modelling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to model and optimize the design of a mine dump by minimizing the total haulage costs. The proposed methodology consists on: (i) Formulation of a dump model based on a system of equations relying on multiple relevant parameters; (ii) Solves by minimizing the total cost using linear programming and determines a ‘preliminary’ dump design; (iii) Through a series of iterations, modifies the ‘preliminary’ footprint by projecting it to the topography and creates the ultimate dump design. Finally, an example application for a waste rock dump illustrates this methodology.

Indoor Positioning Systems (IPSs) are designed to provide solutions for location-based services. Wireless local area network (WLAN)-based positioning systems are the most widespread around the globe and are commonly found to have a ready-to-use infrastructure composed mostly of access points (APs). They provide useful information on signal strength to be processed by adequate location algorithms, which are not always capable of achieving the desired localization error only by themselves. In this sense, this paper proposes a new method to improve the accuracy of IPSs by optimizing some of their most relevant infrastructure components. Included are the arrangement of APs over the environment, the number of reference points (RPs), and the number of samples per location estimation test. A simulation environment is also proposed, in which the impact of key influencing factors on system accuracy is analyzed. Finally, a case study is simulated to validate an optimal combination of design parameters and its compliance with the requirements of localization error and the limited number of access points. Our simulation results clearly show that the desired localization accuracy, which is set as a goal, can be achieved while maintaining the factors already mentioned at minimal levels, which decreases both system deployment costs and computational effort.

Since large power transformers are custom-made, and their design process is a labor-intensive task, their design process is split into different parts. In tendering, the price calculation is based on the preliminary design of the transformer. Due to the complexity of this task, it belongs to the most general branch of discrete, non-linear mathematical optimization problems. Most of the published algorithms are using a copper filling factor based winding model to calculate the main dimensions of the transformer during this first, preliminary design step. Therefore, these cost optimization methods are not considering the detailed winding layout and the conductor dimensions. However, the knowledge of the exact conductor dimensions is essential to calculate the thermal behaviour of the windings and make a more accurate stray loss calculation. The paper presents a novel, evolutionary algorithm-based transformer optimization method which can determine the optimal conductor shape for the windings during this examined preliminary design stage. The accuracy of the presented FEM method was tested on an existing transformer design. Then the results of the proposed optimization method have been compared with a validated transformer design optimization algorithm.

Advancement in physics often results from analyzing numerical data and then creating a theoretical model that can explain and predict those data. In the field of lens design, the reverse is true: longstanding theoretical understanding is being overtaken by more powerful numerical methods.

This paper introduces a new rotor design for the easy insertion and removal of the rotor windings. The shape of the rotor is optimized based on surrogate method in order to achieve the lowest power loss under the maximum power output. The performance of the new rotor is examined in 2-D finite element software and validated by experiments. This rotor shows good potentials for reducing the maintenance and repair costs of synchronous machines, making it suitable for manufacturers within the mass production markets such as gen-sets, steam turbines, wind power generators and hybrid electric vehicles.

Acid fracturing simulation is used widely to optimize carbonate reservoirs and improve acid fracturing treatment performance. In this study, a method was used to minimize the risk of the acid fracturing treatment. First, optimal fracture geometry parameters with UFD methods are calculated. After that, design components change as long as fracture geometry parameters reach their optimal values. The results showed a high flow rate needed to achieve optimal fracture geometry parameters with increasing acid volume. Sensitivity analysis was performed on controllable and reservoir parameters. It observed that a high flow rate should be applied for a low fluid viscosity to achieve the optimization goals. Straight acid reaches optimal conditions at a high flow rate and low volume. These conditions for retarded acids appear only at a low flow rate and high volume. The study of the acid concentration for gelled acid showed that as it increased, the flow rate and volume increased. Besides, for low permeability formation, a large fracture half-length and small fracture width are desirable. In this case, a higher flow rate will be required. The sensitivity analysis showed that the optimum flow rate and acid volume increase and decrease for the high Young's modulus. The effect of closure stress was also investigated and observed for a sample with high closure stress, low flow rate, and high acid volume are required.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

The beautiful and stable posture is essential for ballet. Especially the pirouette which dancers balance themselves on their one leg is one of the most impressive postures. During the pirouette motion, loads from the rotation and the body weight are concentrated to the one leg. Proper ballet shoes can reduce the muscle burden and improve the stability. Four types of shoes; bare feet, running shoes, pointe shoes, and dance sneakers are analyzed. The motion capture system and SIMM are used for the analysis of muscle burden and stability during pirouette. The major 6 muscles in the leg (beceps femoris long head, beceps femoris short head, soleus, rectus femoris, gastrocnemius medialis, and gastrocnemius lateralis) are analyzed, and the effect of rotating velocity is considered. Dance sneakers are outstanding for improving the stability and lessening the muscle burdens in all conditions for beginners. That comes from the design feature of the divided shoe soles and protecting the ankle of the axis leg. With the results and analysis, the direction for design optimization of ballet shoes is suggested. Consequently, this research is about the verification of sports equipment using computer simulation with the musculoskeletal model from a scientific viewpoint of biomechanics.

Desalinators are traditionally driven by fossil-fuels but in order to avoid greenhouse emissions, renewable energy must be used. In this paper, a coupling between multi-stage flash distillation apparatus and a parabolic trough solar collector is analyzed. The purpose of this study is to determine the economic feasibility of the system, considering four cities of Saudi Arabia and three different potable water productions. To avoid solar energy intermittency and unavailability at night, thermal storage is implemented. Whereas other researchers made parametric analyses, in this paper, the authors developed a mathematical program which was optimized with the help of GAMS software, where the capital cost of the plant was the objective function. After that, a life cycle cost analysis was carried out for each scenario. Depending on the region and water production, the costs of drinking water vary from 2.26 to 3.93 US$/m³, and from 7440 to 23825 tons of carbon dioxide emissions are avoided. As a consequence of the approach used, low costs are obtained; even though no auxiliary heater is implemented and the lowest irradiance conditions are considered. The results of this study reflect that the proposed process is competitive with respect to the traditional one.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

The concept of geostationary VHTS (Very High Throughput Satellites) is based on multibeam coverage with intensive frequency and polarization reuse in addition to the use of larger bandwidths in the feeder links, in order to provide high capacity satellite links at a reduced cost per Gbps in orbit. The dimensioning and design of satellite networks based on VHTS imposes the analysis of multiple trade-offs to achieve an optimal solution in terms of cost, capacity and figure of merit of the user terminal. In this paper, we propose a new method for sizing VHTS satellite networks based on an analytical expression of the forward link CINR (Carrier-to-Interference-plus-Noise Ratio) that is used to evaluate the trade-off of different combinations of system parameters. The proposed method considers both technical and commercial requirements as inputs including the constraints to achieve the optimum solution in terms of the user G/T, the number of beams and the system cost. The cost model includes both satellite and ground segments. Exemplary results are presented with feeder links using Q/V bands, DVB-S2X and transmission methods based on CCM and VCM (Constant and Variable Coding and Modulation, respectively) in two scenarios with different service areas.

In this study, a multiobjective, multiperiod, global optimization for design, sizing and dispatch of an islanded, hybrid microgrid was performed using a model built in MATLAB. The system was simulated over one year for sizing and over one day for dispatch, both using hourly time steps. The model minimized lifecycle levelized costs, emissions, lost load and dumped power while maximizing penetration of clean, renewable sources in the microgrid. This found optimal capacities of the renewable, energy storage and backup generation components which provide the best combination of affordability, sustainability, reliability and efficiency. After experimenting with several global solvers, it was determined that particle swarm optimization is most well-suited to solving the sizing optimization problem. The PV-wind microgrid using Li-ion batteries along with diesel engines was found to perform best among all the combinations considered. It was found that in spite of including additional objectives, monetary costs are the primary driver while allocating generation capacity between different renewable sources like wind versus solar PV. Furthermore, the sizing of PV, wind and battery storage depends strongly on the rating of the standby distributed generator, mainly due to reliability consideration. Generating Pareto-optimal sets revealed interesting relationships between different input variables (i.e. PV, wind and battery capacities) as well as trade-offs that arise while pursuing different objectives. Pursuing cost-minimization alone may lead to sub-optimal outcomes in terms of environmental impact, reliability and excess energy production. A sensitivity analysis was also conducted to understand the effects of various parameters like fuel price and energy storage costs on the optimal system's design and operation. Such accurate sizing programs help reduce the extent of oversizing of sub-systems during the design and planning stage, which is usually needed to achieve high reliability with distributed and decentralized energy systems like off-grid microgrids. This reduces the upfront capital investment needed to build the system, making clean electricity access affordable in the short term. The economic-environmental dispatch produced day-ahead scheduling strategies to meet the above mentioned objectives. The system was found to be relatively robust to short-term uncertainties and disturbances in renewable generation and load, although this does cause sub-optimal performance due to increased reliance on fossil fuels. It was found that dispatching of the batteries and backup generators is most critical in minimizing impacts of such events. However, the response to longer-term disturbances still remains to be assessed. The study also includes a comprehensive literature review of tools available for microgrid design as well as different optimization algorithms that have been used to solve microgrid sizing, dispatch and scheduling problems. Additionally, an overview is provided of various control strategies that can be used to improve robustness and resiliency of microgrids.

Renewable energy sources (RES) will play a crucial role in future sustainable energy systems. In scenarios analyzing future energy system designs, a detailed spatial and temporal representation of renewable-based electricity generation is essential. For this, sufficiently representative weather data are required. Most analyses performed in this context use the historical data of either one specific reference year or an aggregation of multiple years. In contrast, this study analyzes the impact of different weather years based on historical weather data from 1980 through 2015 in accordance with the design of an exemplary future energy system. This exemplary energy system consists of on- and offshore wind energy for power-to-hydrogen via electrolysis, including hydrogen pipeline transport for most southwestern European countries. The assumed hydrogen demand for transportation needs represents a hypothetical future market penetration for fuel cell-electric vehicles of 75%. An optimization framework is used in order to evaluate the resulting system design with the objective function of minimizing the total annual cost (TAC) of the system. For each historical weather year, the applied optimization model determines the required capacities and operation of wind power plants, electrolyzers, storage technologies and hydrogen pipelines to meet the assumed future hydrogen demand in a highly spatially- and temporally-detailed manner, as well as the TAC of the system. Following that, the results of every individual year are compared in terms of installed capacities, overall electricity generation and connection to the transmission network, as well as the cost of these components within each region. The results reveal how sensitive the final design of the exemplary system is to the choice of the weather year. For example, the TAC of the system changes by up to 20% across two consecutive weather years. Furthermore, significant variation in the optimization results regarding installed capacities per region with respect to the choice of weather years can be observed.

In this paper, we propose an efficient numerical computation method of reduced-order controller design for linear time-invariant systems. The design problem is described by linear matrix inequalities (LMIs) with a rank constraint on a structured matrix, due to which the problem is NP-hard. Instead of the heuristic method that approximates the matrix rank by the nuclear norm, we propose a numerical projection onto the rank-constrained set based on the alternating direction method of multipliers (ADMM). Then the controller is obtained by alternating projection between the rank-constrained set and the LMI set. We show the effectiveness of the proposed method compared with existing heuristic methods, by using 95 benchmark models from the COMPLeib library.

This work explores an additive-manufacturing-enabled combination-of-function approach for design of modular products. AM technologies allow the design and manufacturing of nearly free-form geometry, which can be used to create more complex, multi-function or multi-feature parts. The approach presented here replaces sub-assemblies within a modular product or system with more complex single parts that are designed and manufactured using AM technologies. This approach can increase the reliability of systems and products by reducing the number of interfaces, as well as allowing the optimization of the more complex parts during the design. The smaller part count and the ability of users to replace or upgrade the system or product parts on-demand should reduce user risk, life-cycle costs, and prevent obsolescence for the user of many systems. This study presents a detailed review on the current state-of-the-art in modular product design in order to demonstrate the place, need and usefulness of this AM-enabled method for systems and products that could benefit from it. A detailed case study is developed and presented to demonstrate the concepts.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

Ice covering on overhead transmission lines would cause damage to transmission system and long-term power outage. Among various de-icing devices, modular multilevel converter (MMC) based DC de-icer (MMC-DDI) is recognized as a promising solution due to its excellent technical performance. Its principle feasibility has been well studied, but few literature discuss its economy or hardware optimization, thus the designed MMC-DDI for high voltage transmission lines is usually too large and too expensive for engineering applications. To fill this gap, this paper presents a quantitative analysis on the converter characteristics of MMC-DDI, and calculates the minimal converter rating and its influencing factors. It reals that, for a given de-icing requirement, the converter rating varies greatly with its AC-side voltage. Then an optimization configuration is proposed to reduce the converter rating and improve its economy. The proposed configuration is verified in a MMC-DDI for a 500kV transmission line as a case study. The result shows, in the case of outputting same de-icing characteristics, the optimized converter rating is reduced from 151 MVA to 68 MVA, and total cost of MMC-DDI is reduced by 48%. This analysis and conclusion are conductive to the optimized design of multilevel DC de-icer, then to its engineering application.

Background: With the trend of intelligent display, the interface design of in-vehicle HUD is an expanding research field; Methods: To solve the subjectivity and uncertainty in the optimization of HUD interface design schemes, this paper proposed a hybrid scheme evaluation and optimization method based on entropy weight and VIKOR. The entropy weight method was used to reduce the subjectivity the decision-maker's weighting and obtain the objective weight of each indicator; The VIKOR method was used to obtain the best ranking of alternative schemes, and then the optimal interface design scheme was selected; Results: The evaluation of in-vehicle HUD interface design schemes were taken as an example for verification and calculation. The results showed that this method considers the subjectivity and uncertainty of the decision-making process in the optimization of design scheme, which can effectively improve the objectivity and accuracy of the evaluation results, and provide a reference for designers to optimize interface design schemes.

To realize structural vibration control,a two parameters H2 optimization design was proposed to optimize the tuning ratio and damping ratio for electromagnetic tuned mass damper (EMTMD). The control effect of this two parameters optimization design is better than that of classical tuned mass damper (TMD).For this two parameters optimization,the most important thing is that the inductance of the coil can be set very small and the external load resistance can be positive ,which can avoid the use of complex negative impedance circuit. If Ref.[6] were designed according to the H2 optimization of two parameters, the EMTMD can be used for multi-modal vibration control of structures without connecting negative inductance and negative resistance spontaneously.

The use of commodity polymers such as polypropylene (PP) is key to open new market segments and applications for the additive manufacturing industry. Technologies such as powder-bed fusion (PBF) can process PP powder; however, much is still to learn concerning process parameters for reliable manufacturing. This study focusses in the process-property relationships of PP using laser-based PBF. The research presents an overview of the intrinsic and the extrinsic characteristic of a commercial PP powder as well as fabrication of tensile specimens with varying process parameters to characterize tensile, elongation at break, and porosity properties. The impact of key process parameters, such as power and scanning speed are systematically modified in a controlled design of experiment. The results were compared to the existing body of knowledge; the outcome is to present a process window and optimal process parameters for industrial use of PP. The computer tomography data revealed a highly porous structure inside specimens ranging between 8.46% and 10.08%, with porosity concentrated in the interlayer planes in the build direction. The results of the design of experiment for this commercial material show a narrow window of 0.122 ≥ Ev ≥ 0.138 J/mm³ led to increased mechanical properties while maintaining geometrical stability.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

Multiphase systems are important in minerals processing, and usually include solid-solid and solid-fluid systems. Examples of operations in multiphase systems include flotation, dewatering, and magnetic separation, among several other unit operations. In this paper, the current trends in the process system engineering tasks of modeling, design, and optimization, in multiphase systems, are analyzed. Different scales of size and time are included, and therefore the analysis includes modeling at the molecular level and unit operation level, and the application of optimization for the design of a plant. New strategies for the modeling and optimization of multiphase systems are also included, with a strong focus on the application of artificial intelligence (AI) and the combination of experimentation and modeling with response surface methodology (RSM). The paper finishes with tools to study the uncertainty, both epistemic and stochastic, which is present in all mineral processing operations. It is shown that all these areas are very active and can help to understand, operate, design, and optimize mineral processing that involves multiphase systems.

In this paper, we consider a reconfigurable intelligent surface (RIS)-assisted integrated satellite-high altitude platform-terrestrial networks (IS-HAP-TNs) that can improve network performance by exploiting HAP's stability and RIS's reflection. Specifically, the reflector RIS is installed on the side of HAP to reflect signals from the multiple ground user equipments (UEs) to the satellite. To aim at maximising system sum rate, we jointly optimize the transmit beamforming matrix at the ground UEs and RIS phase shift matrix. Due to the limitation of the unit modulus of the RIS reflective elements constraint, the combinatorial optimization problem is difficult to tackle it effectively by traditional solving methods. Based on this, this paper studies deep reinforcement learning (DRL) algorithm to achieve online decision making for this joint optimization problem. In addition, it is verified through simulation experiments that the proposed DRL algorithm outperforms the standard scheme in terms of system performance and execution time, and higher computing speed, making real-time decision making truly feasible。

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

Plasmodium falciparum dihydroorotate dehydrogenase (PfDODH) is one of the enzymes currently explored in the treatment of malaria. Although there is currently no clinically approved drug targeting PfDODH, many of the compounds in clinical trials have [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine backbone structure. This study sought to design new compounds from the fragments of known experimental inhibitors of PfDODH. Nine experimental compounds retrieved from Drug Bank online were downloaded and broken into fragments using Schrodinger power shell; the fragments were recombined to generate new ligand structures using BREED algorithm. The new compounds were docked with PfDODH crystal structure, after which the compounds were filtered with extensive drug-likeness and toxicity parameters. A 2D-QSAR model was built using the multiple linear regression method and externally validated. The compounds electronic behaviours were studied using DFT calculations. Structural investigation of the six designed compounds, which had lower binding energies than the standard inhibitors, showed that five of them had [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine moieties and interacted with essential residues at the PfDODH binding site. In addition to their drug-like and pharmacokinetic properties, they also showed minimal toxicities. The externally validated 2D-QSAR model with R² and Q² values of 0.6852 and 0.6691, confirmed the inhibitory prowess of these compounds against PfDODH. The DFT calculations showed regions of the molecules prone to electrophilic and nucleophilic attack. The current study thus provides insight into the development of a new set of potent PfDODH inhibitors.

Statistical modeling lies at the heart of product design and development throughout numerous engineering disciplines, especially since processing large amounts of data has become increasingly ubiquitous. While mathematical statistics provide elegant guidance pertaining to the question of whether or not some particular underlying modeling assumptions are justified and appropriate, when pursuing a more comprehensive assessment of product design and development other considerations often increase in significance. Therefore, we will examine and analyze the tedious interactions and implications of statistical modeling choices and product liability exposure. To the best of our knowledge, this paper is the first to draw attention to and explore some often overlooked or oversimplified dangers and pitfalls that enter the equation when product design heavily relies on statistical modeling. In particular, through a diligent analysis of both statistical and legal aspects we will explore how statistically optimal procedures may yield far from optimal outcomes in terms of product liability when applied to actual real life problems and why suboptimal nonparametric or robust approaches may constitute better alternatives.

Background: The aim of the present investigation was to evaluate the clinical success of horizontal ridge augmentation in the severely atrophic maxilla (Cawood and Howell class IV) using freeze-dried custom made bone harvested from cadaver donors tibial hemiplateau and to analyze the marginal bone level gain prior dental implants placement at 9 months after bone grafting and before prosthetic rehabilitation. Methods: A 52-year-old woman received custom made bone grafts. Patient underwent CT scans 2 weeks prior and 9 months after surgery for graft volume and density analysis. Results: The clinical and radiographic bone observations showed a very low rate of resorption after bone graft and implant placement. Conclusions: The custom-made allograft material was a highly effective modality for restoring the alveolar horizontal ridge, resulting in this way to reduce the need to obtain autogenous bone from a secondary site with predictable procedure. Further studies are needed to investigate its behavior at longer time points.

The innovation driven Industry 5.0, in agreement with Industry 4.0, leads to consider human in a prominence position as the center of manufacturing field. This pushes towards the hybridization of manufacturing plants promoting a fully collaboration between human and robot. Furthermore, the new paradigm of "human centred design" and "anthropocentric design" allows enabling a synergistic combination of human and robot skills. However, properly collaborative workplaces are currently very few. Industry is still not confident, and systems integrators hesitate to venture into Human-Robot Collaboration (HRC). Despite the effort in collaborative robotics, a general solution to overcome the current limitations in designing of collaborative workplaces still misses. In the current work, a Knowledge-Based Approach (KBA) is adopted to face collaborative workplace designing problem. The framework resulting from the KBA allows developing a modelling paradigm that enable to define a streamlined approach for the layout designing of a collaborative workplace. Finally, a what-if analysis and a ANOVA analysis are performed to generate and evaluate a set of scenarios related to a collaborative workplace for quality inspection of welded parts. Facing the high complexity and multidisciplinary of HRC can be conveyed to develop a general design approach aimed at overcoming the difficulties that limit the spread of HRC in the manufacturing field.

Multi-objective optimization (MOO) is an optimization involving minimization or maximization of several objective functions more than the conventional one objective optimization, which is useful in many fields. Many of the current methodologies addresses challenges and solutions that attempt to solve simultaneously several Objectives with multiple constraints subjoined to each. Often MOO are generally subjected to linear inequality, equality and or bounded constraint that prevent all objectives from being optimized at once. This paper reviews some recent articles in area of MOO and presents deep analysis of Random and Uniform Entry-Exit time of objectives. It further break down process into sub-process and then provide some new concepts for solving problems in MOO, which comes due to periodical objectives that do not stay for the entire duration of process lifetime, unlike permanent objectives which are optimized once for the entire process duration. A methodology based on partial optimization that optimizes each objective iteratively and weight convergence method that optimizes sub-group of objectives are given. Furthermore, another method is introduced which involve objective classification, ranking, estimation and prediction where objectives are classified based on their properties, and ranked using a given criteria and in addition estimated for an optimal weight point (pareto optimal point) if it certifies a coveted optimal weight point. Then finally predicted to find how far it deviates from the estimated optimal weight point. A Sample Mathematical Tri-Objectives and Real world Optimization was analyzed using partial method, ranking and classification method, the result showed that an objective can be added or removed without affecting previous or existing optimal solutions. Therefore suitable for handling time governed MOO. Although this paper presents concepts work only, it’s practical application are beyond the scope of this paper, however base on analysis and examples presented, the concept is worthy of igniting further research and application.

A Robust Optimization framework with original concepts and fundamentals also admitting a fusion of ideals from relative regret models and static robust optimization, containing conservatism concepts is disclosed. The algorithm uses a fine-tune strategy to tune the model so the robustness and a target ideality can be mutually achieved with a specified risk. The framework comprises original concepts, a mathematical approach and an algorithm. The statistical treatment of the data with the original concepts from the framework make it able to make short, middle or long-term decision-making setting. The framework has high tractability since the algorithm forces the creation of a setting that makes a robust optimization with the specified risk. The framework can be applied in linear and nonlinear mathematical models since that the objective function is monotonic in the domain of the active convex region. Several examples are solved to best understand the framework and all results demonstrated high tractability and performance. There is a wide range of applications. Along all the text, there is a profound discussion about its philosophy, objective, original concepts, fields of application, statistical and probabilistic fundamentals.

Global optimization is an imperative development of local optimization because there are many problems in artificial intelligence and machine learning requires highly acute solutions over entire domain. There are many methods to resolve the global optimization, which can be classified into three groups such as analytic methods (purely mathematical methods), probabilistic methods, and heuristic methods. Especially, heuristic methods like particle swarm optimization and ant bee colony attract researchers because their effective and practical techniques which are easy to be implemented by computer programming languages. However, these heuristic methods are lacking in theoretical mathematical fundamental. Fortunately, minima distribution establishes a strict mathematical relationship between optimized target function and its global minima. In this research, I try to study minima distribution and apply it into explaining convergence and convergence speed of optimization algorithms. Especially, weak conditions of convergence and monotonicity within minima distribution are drawn so as to be appropriate to practical optimization methods.

Particle swarm optimization (PSO) is an effective algorithm to solve the optimization problem in case that derivative of target function is inexistent or difficult to be determined. Because PSO has many parameters and variants, I propose a general framework of PSO called GPSO which aggregates important parameters and generalizes important variants so that researchers can customize PSO easily. Moreover, two main properties of PSO are exploration and exploitation. The exploration property aims to avoid premature converging so as to reach global optimal solution whereas the exploitation property aims to motivate PSO to converge as fast as possible. These two aspects are equally important. Therefore, GPSO also aims to balance the exploration and the exploitation. It is expected that GPSO supports users to tune parameters for not only solving premature problem but also fast convergence.

Increasing demand for food production with limited available water resources pose the threat to agricultural activities. The conjunctive allocation of water resources maximizes the net benefit of farmers efficiently. In this study, a novel hybrid optimization model was developed based on a genetic algorithm (GA), bacterial foraging optimization (BFO) and ant colony optimization (ACO) to maximize the net benefit of water deficit Sathanur reservoir command. The GA-based opti-mization model considered crop-related physical and economical parameters to derive optimal cropping patterns for three different conjunctive use policies and further allocation of surface and groundwater for different crops are enhanced with the BFO. The allocation of surface and groundwater for the head, middle and tail reach obtained from BFO is considered as input to ACO as a guiding mechanism to attain an optimal cropping pattern. Comparing the average produc-tivity values Policy 3 (3.665 Rs/m3) has better values relating to Policy 1 (3.662 Rs/m3) and Policy 2 (3.440 Rs/m3). Thus, the developed novel hybrid optimization model (GA-BFO-ACO) is very promising to enhance the farmer's net income as well as for the command area water conservation and can be replicated in other irrigated regions of the globe to overcome chronic land and water problems.

Recent research has enabled the integration of traditional Volt-VAr Control (VVC) resources, such as capacitors banks and transformer tap changers, with Distributed Energy Resources (DERs), such as photo-voltaic sources and energy storage, in order to achieve various Volt-VAr Optimization (VVO) targets, such as Conservation Voltage Reduction (CVR), minimizing VAr flow at the transformer, minimizing grid losses, minimizing asset operations and more. When more than one target function can be optimized, the question of multi-objective optimization is raised. In this work, we propose a general formulation of the multi-objective Volt-VAr optimization problem. We consider the applicability of various multi-optimization techniques and discuss the operational interpretation of these solutions. We demonstrate the methods using simulation on a test feeder.

The main goal of this paper is to show that Bayesian optimization could be regarded as a general framework for the data driven modelling and solution of problems arising in water distribution systems. Hydraulic simulation, both scenario based, and Monte Carlo is a key tool in modelling in water distribution systems. The related optimization problems fall in a simulation/optimization framework in which objectives and constraints are often black-box. Bayesian Optimization (BO) is characterized by a surrogate model, usually a Gaussian process, but also a random forest and increasingly neural networks and an acquisition function which drives the search for new evaluation points. These modelling options make BO nonparametric, robust, flexible and sample efficient particularly suitable for simulation/optimization problems. A defining characteristic of BO is its versatility and flexibility, given for instance by different probabilistic models, in particular different kernels, different acquisition functions. These characteristics of the Bayesian optimization approach are exemplified by the two problems: cost/energy optimization in pump scheduling and optimal sensor placement for early detection on contaminant intrusion. Different surrogate models have been used both in explicit and implicit control schemes. Showing that BO can drive the process of learning control rules directly from operational data. BO can also be extended to multi-objective optimization. Two algorithms have been proposed for multi-objective detection problem using two different acquisition functions.

Many combinatorial optimization problems are hard to solve within the polynomial computational time or NP-hard problems. Therefore, developing new optimization techniques or improving existing ones still grab attention. This paper presents an improved variant of the Ant Colony Optimization meta-heuristic called Enhanced Hyper Cube Framework ACO (EHCFACO). This variant has an enhanced exploitation feature that works through two added local search movements of insertion and bit flip. In order to examine the performance of the improved meta-heuristic, a well-known structural optimization problem of laminate Stacking Sequence Design (SSD) for maximizing critical buckling load has been used. Furthermore, five different ACO variants were concisely presented and implemented to solve the same optimization problem. The performance assessment results reveal that EHCFACO outperforms the other ACO variants and produces a cost-effective solution with considerable quality.

The research paper presents a new approach towards constructing motion equations for structures with attached MTMDs (multiple tuned mass dampers). A primary system, with MDOF (multiple dynamic degrees of freedom) was reduced to an equivalent system with a SDOF (single degree of freedom) through the modal approach, and equations from additional MTMDs were added to a thus-created system. Optimization based on H2 and H∞ for the transfer function associated with the generalized displacement of an SDOF system. The research work utilized GA (genetic algorithms) and SA (simulated annealing method) optimization algorithms to determine the stiffness and damping parameters for individual TMDs. The effect of damping and stiffness (MTMD tuning) distribution depending on the number of TMDs was also analyzed. The paper also reviews the impact of primary system mass change on the efficiency of optimized MTMDs, as well as confirms the results of other authors involving greater MTMD effectiveness relative to a single TMD.

We developed a novel hybrid approach for solving global optimization, computer science, bio-medical and engineering real life applications that is based on the coupling of the Whale Optimizer and Sine Cosine Algorithms via a surrogate model. We relate the whale optimizer algorithm to balance between the exploitation and the exploration process in the proposed method. There exist confirmed techniques for searching approximate best optimal solutions, but our algorithm will further guarantee that such numerical and statistical solutions satisfy physical bounds of the standard and real life functions. Our experiments with the benchmark, bio-medical, computer science and engineering real life problems have illustrated the advantages of using a newly hybrid approach based on mixing Whale Optimizer and Sine Cosine algorithms. It holds considerable potential for reducing execution time for solving standard and real life problems and at the same time improving the quality of the solution.

With the every passing day, the demand for data traffic is increasing and this demand forces the research community not only to look for alternating spectrum for communication but also urges the radio frequency planners to use the existing spectrum smartly. Cell size is shrinking with the every upcoming communication generation which makes the base station placement planning complex and cumbersome. In order to make the next-generation cost-effective, it is important to design the network in such a way which utilizes minimum number of base stations while ensure coverage and quality of service. This paper aims at develop a new approach using hybrid metaheuristic and metamodel applied in multi-transmitter placement planning (MTPP) problem. We apply radial basis function (RBF) metamodel to assist particle swarm optimizer (PSO) in a constrained simulation-optimization (SO) of MTPP to mitigate the associated computational burden of optimization procedure. We evaluate the effectiveness and applicability of proposed algorithm in a case study by simulating MTPP model with two, three, four and five transmitters.

Baggage overweight is a significant phenomenon in the air travel in- dustry which is both regulated by the governments and highly profitable for the airlines. The recent years increase in airlines' profits is attributed to so-called ancillary payments – all consumer costs excluding the actual transportation fare. Baggage overweight fees, being a part of such pay- ments, have high profit-generation potential. Is the pricing for baggage overweight positioned correctly? The rationality of policies currently used by airlines is questionable, as they lack a customer-oriented marketing ap- proach. The general purpose of this research is to explore the possibilities of rational baggage overweight pricing for airlines by developing a multi- level price optimization model aimed to maximize company revenue. The modeling is based on determining consumer Willingness-To- Pay values for baggage overweight, and providing an optimal ticket price for them to maximize company expected revenue. The total profit value is forecasted too, based on the company market share and revenue level.

One control challenge in prosthetic legs is seamless transition from one gait mode to another. User intent recognition (UIR) is a high-level controller that tells a low-level controller to switch to the identified activity mode, depending on the user’s intent and environment. We propose a new framework to design an optimal UIR system with simultaneous maximum performance and parsimony for gait mode recognition. We use multi-objective optimization (MOO) to find an optimal feature subset that creates a trade-off between these two conflicting objectives. The main contribution of this paper is two-fold: (1) a new gradient-based multi-objective feature selection (GMOFS) method for optimal UIR design; and (2) the application of advanced evolutionary MOO methods for UIR. GMOFS is an embedded method that simultaneously performs feature selection and classification by incorporating an elastic net in multilayer perceptron neural network training. Experimental data are collected from six subjects, including three able-bodied subjects and three transfemoral amputees. We implement GMOFS and four variants of multi-objective biogeography-based optimization (MOBBO) for optimal feature subset selection, and we compare their performances using normalized hypervolume and relative coverage. GMOFS demonstrates competitive performance compared to the four MOBBO methods. We achieve a mean classification accuracy of 97.14% ± 1.51% and 98.45% ± 1.22% with the optimal selected subset for able-bodied and amputee subjects, respectively, while using only 23% of the available features. Results thus indicate the potential of advanced optimization methods to simultaneously achieve accurate, reliable, and compact UIR for locomotion mode detection of lower-limb amputees with prostheses.

In recent years, new metaheuristic algorithms have been developed taking as reference the inspiration on biological and natural phenomena. This nature-inspired approach for algorithm development has been widely used by many researchers in solving optimization problem. These algorithms have been compared with the traditional ones algorithms and have demonstrated to be superior in complex problems. This paper attempts to describe the algorithms based on nature, that are used in fuzzy clustering. We briefly describe the optimization methods, the most cited nature-inspired algorithms published in recent years, authors, networks and relationship of the works, etc. We believe the paper can serve as a basis for analysis of the new are of nature and bio-inspired optimization of fuzzy clustering.

The growing interest in the use of energy storage systems to improve the performance of tramways has prompted the development of control techniques and optimal storage devices, displacement, and sizing to obtain the maximum profit and reduce the total installation cost. Recently, the rapid diffusion of renewable energy generation from photovoltaic panels has also created a large interest in coupling renewable energy and storage units. This study analyzed the integration of a photovoltaic power plant, supercapacitor energy storage system, and railway power system. Random optimization was used to verify the feasibility of this integration in a real tramway electric system operating in the city of Naples, and the benefits and total cost of this integration were evaluated.

Classical and optimal control architectures for motion mechanics with fusion of noisy sensors use different algorithms and calculations to perform and control any number of physical demands, to varying degrees of accuracy, precision, and cost. Their performances are tested for the purpose of comparison through the means of a Monte Carlo simulation that simulates how different parameters might vary under noise, representing real-world imperfect sensors. We find that improvements in one figure of merit often come at a cost in the performance in the others, especially depending on the presence of noise in the system sensors. If sensor noise is negligible, open-loop optimal control performs the best. However, in the overpowering presence of sensor noise, using a control law inversion patching filter performs as the best replacement, but has significant computational strain.

Structural system design is the process of giving form to a set of interconnected components subjected to loads and design constraints while navigating a complex design space. While safe designs are relatively easy to develop, optimal designs are not. Modern computational optimization approaches employ population based metaheuristic algorithms to overcome challenges with the system design optimization landscape. However, the choice of the initial population, or ground structure, can have an outsized impact on the resulting optimization. This paper presents a new method of generating such ground structures, using a combination of topology optimization (TO) and a novel system extraction algorithm. Since TO generates monolithic structures, rather than systems, its use for structural system design and optimization has been limited. In this paper, truss systems are extracted from topologies through morphological analysis and artificial intelligence techniques. This algorithm, and its assessment, constitutes the key contributions of this paper. The structural systems obtained are compared with ground truth solutions to evaluate the performance of the algorithms. The generated structures are also compared against benchmark designs from the literature. The results indicate that the presented truss generation algorithm produces structures comparable to those generated through metaheuristic optimization, while mitigating the need for assumptions about initial ground structures.

This paper presents a multi-swarm PSO algorithm for the Quadratic Assignment Problem (QAP) implemented on the OpenCL platform. Our work was motivated by results of time efficiency tests performed for single-swarm algorithm implementation that showed clearly that the benefits of a parallel execution platform can be fully exploited provided the processed population is large. The described algorithm can be executed in two modes: with independent swarms or with migration. We discuss the algorithm construction as well as we report results of tests performed on several problem instances from the QAPLIB library. During the experiments the algorithm was configured to process large populations. This allowed us to collect statistical data related to values of goal function reached by individual particles. We use them to demonstrate on two test cases that although single particles seem to behave chaotically during the optimization process, when the whole population is analyzed, the probability that a particle will select a near-optimal solution grows.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

The load of power system changes with the development of economy, short-term load forecasting play a very important role in dispatching and management of power system. In this paper, the Ant Lion Optimizer (ALO) is introduced to improve the input weights and hidden-layer Matrix of extreme learning machine (ELM), after the parameters of ELM are optimized by ALO, then input nodes, hidden layer nodes and output nodes are determined, so a load forecasting model based on ALO-ELM combined algorithm is established. The proposed method is illustrated based on the historical load data of a city in China. The results show that the average absolute error of short-term load demand predicted by ALO-ELM model is 1.41, while that predicted by ELM is 4.34, the proposed ALO-ELM algorithm is superior to the ELM and meet the requirements of engineering accuracy, which proves the effectiveness of proposed method.

This work proposes a systematic topology optimization approach to simultaneously design the morphing functionality and actuation in three-dimensional wing structures. The actuation is assumed to be a linear strain-based expansion in the actuation material and a three-phase material model is employed to represent structural and actuating materials, and void. To ensure both structural stiffness with respect to aerodynamic loading and morphing capabilities, the optimization problem is formulated to minimize structural compliance while morphing functionality is enforced by constraining a morphing error between actual and target wing shape. Moreover, a feature mapping approach is utilized to constrain and simplify actuator geometries. A trailing edge wing section is designed to validate the proposed optimization approach. Numerical results demonstrate that three-dimensional optimized wing sections utilize a more advanced structural layout to enhance structural performance while keeping morphing functionality than two-dimensional wing ribs. The work presents the first step towards systematic design of three-dimensional morphing wing sections.

Wireless Sensor Networks (WSNs) has the characteristics of large-scale deployment, flexible networking, and wide application. It is an important part of the wireless communication networks. However, due to limited energy supply, the development of WSN is greatly restricted. Wireless Rechargeable Sensor Networks (WRSNs) transform the distributed energy around the environment into usable electricity through energy collection technology. In this work, a joint optimization strategy is proposed to improve the energy management efficiency for WRSNs. The joint optimization strategy is divided into two phases. In the first phase, we design an Annulus Virtual Force based Particle Swarm Optimization (AVFPSO) algorithm for area coverage planing. It adopts the multi-parameter joint optimization method to improve the efficiency of the algorithm. In the second phase, a Queuing Game-based Energy Supply (QGES) algorithm is designed for energy scheduling. It converts energy supply and consumption into network service. By solving the game equilibrium of the model, the optimal energy distribution strategy can be obtained. The simulation results show that our scheme improves the efficiency of coverage and energy, and extends the lifetime of WSN.

The continuous development in the field of industrial automation and electric mobility has led to the need for more efficient electrical machines with high power density. The improvement of electrical machines slot filling factors is one of the measures to satisfy these requirements. In recent years, this topic has aroused greater interest in the industrial sector, since the evolution of the winding technological manufacturing processes allows an economically sustainable realization of ordered winding arrangements, rather than random ones. Moreover, the manufacture of electrical machines windings must be preceded by an accurate design phase in which it is possible to evaluate the maximum slot filling factor obtainable for a given wire shape and for its dimensions. For this purpose, this paper presents an algorithmic approach for the evaluation of maximum slot filling factors in electrical machines under ideal geometric premise. In particular, this algorithm has a greater degree of flexibility with respect to the algorithm approaches found in the literature, since the study has been extended to round, rectangular and hexagonal wire sections. Furthermore, the slot filling factor calculation was carried out both for standard and non-standard slots. The algorithmic approach proposed can be considered as an additional useful tool for the fast design of electrical machine windings.

Deep learning, specifically the supervised approach, has proved to be a breakthrough in depth prediction. However, the generalization ability of deep networks is still limited, and they cannot maintain a satisfactory performance on some inputs. Addressing a similar problem in the segmentation field, a scheme (f-BRS) has been proposed to refine predictions in the inference time. f-BRS adapts an intermediate activation function to each input by using user clicks as sparse labels. Given the similarity between user clicks and sparse depth maps, this paper aims at extending the application of f-BRS to depth prediction. Our experiments show that f-BRS, fused with a depth estimation baseline, is trapped in local optima, and fails to improve the network predictions. To resolve that, we propose a double-stage adaptive refinement scheme (DARS). In the first stage, a Delaunay-based correction module significantly improves the depth generated by a baseline network. In the second stage, a particle swarm optimizer (PSO) delineates the estimation through fine-tuning f-BRS parameters—that is, scales and biases. DARS is evaluated on an outdoor benchmark, KITTI, and an indoor benchmark, NYUv2 while for both the network is pre-trained on KITTI. The proposed scheme outperformed rival methods on both datasets.

In the aim of improving the positioning accuracy of monocular visual inertial simultaneous localization and mapping (VI-SLAM) system, an improved initialization method with faster convergence is proposed. This approach is classified as three parts: Firstly, in the initial stage, the pure vision measurement model of ORB-SLAM is employed to make all the variables visible. Secondly, the frequency of IMU camera was aligned by IMU preintegration technology. Thirdly, an improved iterative method is put forward for estimating the initial parameters of IMU faster. The estimation of IMU initial parameters is divided into several simpler sub-problems, containing direction refinement gravity estimation, gyroscope deviation estimation, accelerometer bias and scale estimation. The experimental results on the self-built robot platform show that our method can up-regulate the initialization convergence speed, simultaneously improve the positioning accuracy of the entire VI-SLAM system.

Hydrogen used as an energy carrier can provide an important route to the decarbonization of energy supplies. However, realizing this opportunity requires a significant increase in both production and transportation capacity. Part of the increase in transportation capacity could be provided by the shipping of liquid hydrogen, but this introduces an energy-intensive liquefaction step into the supply-chain. The energy required for liquefaction can be reduced by developing improved process designs, but since all low-temperature processes are affected by the available heat-sink temperature, local ambient conditions will also affect the energy penalty. This work studies how the energy consumption associated with liquefaction varies with heat-sink temperature through the optimization of design parameters for a typical next-generation hydrogen liquefaction process. The results show that energy consumption increases by around 20%, across the cooling temperature range 5 to 50 °C. Considering just the range 20 to 30 °C there is a 5% increase, illustrating the significant impact ambient temperature can have on energy consumption.

This paper describes a new optimization methodology of testing vector sets reduction for testing of soft-processor cores and their individual blocks. The deterministic test vectors both for whole core and its individual blocks are investigated that significantly reduce the testing time and amount of test data that needs to be stored on the tester memory. The processor executes an assembler program which together with determined testing vectors ex-ercise its functionality. The new BIST methodology applicable at industrial testing of processor cores, diagnostics and dynamic reconfiguration of FPGA is proposed. This novel methodology combined with dynamic reconfiguration of FPGAs can be profitable applied for missions-critical i.e. FPGAs operate in space, or other difficult condition where are explore on radiation. Experimental results demonstrate that the proposed approach reduces many times testing time.

The aim of this paper is to examine the beneficial impact of feedback information in the dynamics of production-inventory control systems. Two production-inventory control system models are analyzed: APIOBPCS and 2APIOBPCS models. The simulation-based experiment designs were conducted by using the state-space equations of the two models. The bullwhip effect as measured by the variance ratio between the order rate and the consumption rate, and inventory responsiveness as measured by the Integral of Absolute Error between the actual and the target levels of inventory, are two metrics used to evaluate the performance of the production-inventory control system in response to a random customer demand. To ensure that both models work under optimal performance, multi-objective particle swarm optimization (MOPSO) is employed to address the problem of tuning the controller’s parameters. The simulation results show the 2APIOBPCS model outperforms the APIOBPCS model at achieving the desired bullwhip effect and being able to provide better inventory responsiveness. The improvement in the inventory responsiveness becomes more significant when the system operates under mismatched lead time and/or an initial condition.

Highway alignment is an essential part of the highway planning and design phase. Highways are impacted by existing projects and surrounding context. The isolation of geo-technical analysis from highway planning and design also delays the planning process. This study therefore proposes a model that integrates building information modelling (BIM) and geographic information science (GIS) capabilities to facilitate the planning and design process. Semantic web technologies are used to integrate BIM and GIS data on a semantic level. The proposed model also helps to identify geohazards by providing geological analysis. The visualization of the proposed project can help reduce design errors and miscommunication, which, in turn, reduces project risk. In addition, the model facilitates highway alignment optimization by incorporating visualization, simulation, and analysis into the planning and design phase. The proposed model provides future opportunities for project professionals to have organized, reliable and dynamic ways to manage the project during construction.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Q_t-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Qt-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

Currently, maritime traffic is increasing with economic growth in several regions worldwide. However, this growth in maritime traffic has led to increased risk of marine accidents. These accidents have a higher probability of occurring in regions where geographical features, such as islands, are present. Further, the positioning of rescue ships in a particular ocean region with a high level of maritime activity is critical for rescue operations. This paper proposes a method for determining an optimal set of locations for stationing rescue ships in an ocean region with numerous accident sites in the Wando islands of South Korea. The computational challenge in this problem is identified as the positioning of numerous islands of varying sizes located in the region. Thus, the proposed method combines a clustering-based optimization method and an image processing approach that incorporates flood filling to calculate the shortest distance between two points in the ocean that detours around the islands. Experimental results indicate that the proposed method reduces the distance from rescue ships and each accident site by 5.0 km compared to the original rescue ship locations. Thus, rescue time is reduced.

A swarm based nature-inspired optimization algorithm namely fruit fly optimization algorithm (FOA) has simple structure and ease of implementation. However, FOA has a low success rate and a slow convergence because FOA generates new positions around the best location using fixed search radius. Several improved FOAs have been proposed. But their exploration ability is questionable. To make the search process to transit from the exploration phase to the exploitation phase smoothly, this paper proposes a new FOA constructed from a cooperation of the multileader and the probabilistic random walk strategies (CPFOA). It has two population types working together. CPFOA's performance is evaluated by 18 well-known standard benchmark, and 30 CEC’2017 functions. The results showed that CPFOA outperforms both the original FOA and its variants in terms of convergence speed and performance accuracy. The results base on CEC’2017 show that CPFOA can achieve a very promising accuracy when compared with the well-known competitive algorithms. CPFOA is applied to optimize two applications; the MLPs classifying real datasets and extracting parameters of T-S fuzzy system for modelling Box and Jenkins gas furnace data set. CPFOA can find parameters having a very high quality compared with the best known competitive algorithms.

The Vehicle Routing Problem (VRP) and its variants are found in many fields, especially logistics. In this study, we introduced an adaptive method to a complex VRP. It combines multi-objective optimization and several forms of VRPs with practical requirements for an urban shipment system. The optimizer needs to consider terrain and traffic conditions. The proposed model also considers customers' expectations, shipper considerations as goals, and the common goal like transportation cost. We offered compromise programming to approach the multi-objective problem by decomposing the original multi-objective problem into a minimized distance-based problem. We designed a hybrid version of the Genetic algorithm with the Local Search algorithm to solve the proposed problem. We evaluate the effectiveness of the proposed algorithm with the Tabu Search algorithm, the original Genetic algorithm on the tested dataset. The results show that our method is an effective decision-making tool for the multi-objective VRP and an effective solver for the new variation of VRP.

Mixing is considered as a critical process parameter (CPP) during process development due to its significant influence on reaction selectivity and process safety. Nevertheless, mixing issues are difficult to identify and solve owing to their complexity and dependence on knowledge of kinetics and hydrodynamics. In this paper, we proposed an optimization methodology using Computational Fluid Dynamics (CFD) based compartmental modelling to improve mixing and reaction selectivity. More importantly, we have demonstrated that through the implementation of surrogate-based optimization, the proposed methodology can be used as a computationally non-intensive way for rapid process development of reaction unit operations. For illustration purpose, reaction selectivity of a process with Bourne competitive reaction network is discussed. Results demonstrate that we can improve reaction selectivity by dynamically controlling rates and locations of feeding in the reactor. The proposed methodology incorporates mechanistic understanding of the reaction kinetics together with an efficient optimization algorithm to determine the optimal process operation and thus can serve as a tool for quality-by-design (QbD) during product development stage.

Hand gesture recognition has many valuable applications in engineering and health care. This study proposes a novel model which can accurately distinguish hand gestures using forearm muscles' surface electromyogram (sEMG) signals. A deep learning algorithm with hyper parameters impacting the final model’s accuracy and a convolutional neural network (CNN) were employed in the recognition stage. The number of convolutional layers, kernels per layer, and neurons in the dense layer were selected for optimization, while the remaining parameters, such as the learning rate, batch size, and number of epochs, were chosen based on trial and error and prior knowledge. The optimal values for the selected hyperparameters were obtained using a genetic algorithm to achieve maximum recognition accuracy. The UC2018 Dual-Myo database was used for training and testing the model based on EMG signals characterizing the activity of eight different hand gestures. The final structure of the model consisted of two convolutional layers with 131 and 28 kernels, a dense layer with 111 neurons, and a softmax layer with eight neurons. Upon optimizing the hyperparameters using the genetic algorithm, the accuracy of the proposed model increased from 91.86% to 96.4% at best and 95.3% on average in real-time applications and 99.6% in an offline mode. Future work is warranted towards improving the architecture and the computational cost.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

The term STODS (Surgical Temporary Ocular Discomfort Syndrome) has been coined to describe the ocular surface perturbations induced by surgery. As one of the most important refractive elements of the eye, Guided Ocular Surface and Lid Disease (GOLD) optimization is fundamental to success in achieving refractive outcomes and mitigating STODS. Effective GOLD optimization and the prevention/treatment of STODS, requires an understanding of the molecular, cellular and anatomic factors that influence ocular surface microenviroment and the associated perturbations induced by surgical intervention. By reviewing the current understanding of STODS etiologies, we will attempt to outline a rationale for a tailored GOLD optimization depending on the ocular surgical insult. With a bench to bedside approach, we will highlight clinical examples of effective GOLD perioperative optimization can mitigate STODS deleterious effect on preoperative imaging and postoperative healing.

An essential step in solving any topology optimization problem is determining the sensitivities of the objective function and optimization constraints. Unfortunately, these sensitivities are usually derived and implemented manually. Nontrivial objective functions and constraints, especially with the involvement of material and geometric nonlinearities, need strenuous mathematical derivation, leading to error-prone implementation. Another intriguing approach to finding sensitivities is automatic differentiation. This paper uses the automatic differentiation and adjoint method to find the sensitivities for two multiphysics topology optimization problems: 1) thermoelasticity and 2) piezoelectricity. This approach is not limited to these examples and can be easily extended to other single- or multi-physics topology optimization problems.

60\% of the global population is expected to be in cities by 2050. At the same time the climate is changing at an accelerated rate. In this short paper we discuss the conflation of these two phenomena and how it may change the cities of the future. We formulate this as an optimization problem that could help answer important questions such as where are they likely to be located? How are they to be powered? What would be their demand for mobility and how might this be met? How over or under ground might these cities be? This paper first looks at a historical paradigm of cities in the absence of the climate crisis and then proposes the new paradigm to look at cities of the future faced by the challenge of the climate change crisis.

In a one price economy, the Fundamental Theorem of Asset Pricing (FTAP) establishes that no-arbitrage is equivalent to the existence of an equivalent martingale measure. Such an equivalent measure can be derived as the normal unit vector of the hyperplane that separates the attainable gain subspace and the convex cone representing arbitrage opportunities. However, in two-price financial models (where there is a bid-ask price spread), the set of attainable gains is not a subspace anymore. We use convex optimization, and the conic property of this region to characterize the “No-Arbitrage” principle in financial models with the bid-ask price spread present. This characterization will lead us to the generation of a set of price factor random variables. Under such a set, we can find the lower and upper bounds (supper-hedging and sub-hedging bounds) for the price of any future cash flow. We will show that for any given cash flow, for which the price is outside the above range, we can build a trading strategy that provides one with an arbitrage opportunity. We will generalize this structure to any two-price finite-period financial model.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

Proper calibration of eye movement signal registered by an eye tracker seems to be one of the main challenges in popularizing eye trackers as yet another user input device. Classic calibration methods taking time and imposing unnatural behavior of users have to be replaced by intelligent methods that are able to calibrate the signal without conscious cooperation with users. Such an implicit calibration requires some knowledge about the stimulus a person is looking at and takes into account this information to predict probable gaze targets. The paper describes one of the possible methods to perform implicit calibration: it starts with finding probable fixation targets (PFTs), then uses these targets to build a mapping - probable gaze path. Various possible algorithms that may be used for finding PFTs and mapping are presented in the paper and errors are calculated utilizing two datasets registered with two different types of eye trackers. The results show that although for now the implicit calibration provides results worse than the classic one, it may be comparable with it and sufficient for some applications.

Energy system models have become indispensable to shape future energy systems by providing insights into different trajectories. However, sustainable systems with high shares of renewable energy are characterized by growing cross-sectoral interdependencies and decentralized structures. To capture important properties of increasingly complex energy systems, sophisticated and flexible modelling tools are needed. At the same time open science becomes increasingly important in energy system modelling. This paper presents the Open Energy Modelling Framework (oemof) as a novel approach in energy system modelling, representation and analysis. The framework forms a toolbox to construct comprehensive energy system models and has been published open source under a free license. With a collaborative development based on open processes the framework seeks for a maximum level of participation and transparency to facilitate open science principles in energy system modelling. Based on a generic graph based description of energy systems it is well suited to flexibly model complex cross-sectoral systems and incorporate various modelling approaches. This makes the framework a multi-purpose modelling environment for modelling and analyzing different systems ranging from an urban to a transnational scale.

Quantum computers are machines that are designed to use quantum mechanics in order to improve upon classical computers by running quantum algorithms. One of the main applications of quantum computing is solving optimization problems. For addressing optimization problems, we can use linear programming. Linear programming is a method to obtain the best possible outcome in a special case of mathematical programming. Application areas of this problem consist of resource allocation, production scheduling, parameter estimation, etc. In our study, we look at quantum speedup ratios of HHL Algorithm for different scenarios of linear programming. In a first scenario we look quantum speedup ratio (S(N)) as a function of phase transition and the ratio (κ) between the greatest and smallest eigenvalues of the matrix in linear equation system. As a second scenario, we investigate the changes in S(N) as a function of κ and s, which is the coefficient for defining the matrix as s-sparse.

Quantum computers are machines that are designed to use quantum mechanics in order to improve upon classical computers by running quantum algorithms. One of the main applications of quantum computing is solving optimization problems. For addressing optimization problems we can use linear programming. Linear programming is a method to obtain the best possible outcome in a special case of mathematical programming. Application areas of this problem consist of resource allocation, production scheduling, parameter estimation, etc. In our study, we looked at the duality of resource allocation problems. First, we chose a real world optimization problem and looked at its solution with linear programming. Then, we restudied this problem with a quantum algorithm in order to understand whether if there is a speedup of the solution. The improvement in computation is analysed and some interesting results are reported.

Based on collected power generation data associated with solar irradiance, PV system conversion efficiency and cell temperature, an hourly solar PV power estimation model by a parallel artificial neural network (ANN) and particle swarm optimization (PSO) algorithm is proposed. Weight matrices related to different seasons and geographic areas for estimation power generations have been trained by real measured operation data. The parallel PSO algorithm with heuristic global optimization technique assists the ANN training process to get near optimal solutions precisely. The accuracy and reliability of estimation is audited by actual details of photovoltaic power stations in various regions and scales. The results of estimation model can not only assist the electricity dispatcher to explicitly monitor the trend of solar power generation in different areas, but also coordinate with traditional power plants to meet load demand more accurately. The presented model will bring benefits to power dispatching for larger scales of intermittent and unstable solar power generation.

Selecting a feature in data mining is one of the most challenging and important activities in pattern recognition. The issue of feature selection is to find the most important subset of the main features in a specific domain, the main purpose of which is to remove additional or unrelated features and ultimately improve the accuracy of the categorization algorithms. As a result, the issue of feature selection can be considered as an optimization problem and to solve it, meta-innovative algorithms can be used. In this paper, a new hybrid model with a combination of whale optimization algorithms and flower pollination algorithms is presented to address the problem of feature selection based on the concept of opposition-based learning. In the proposed method, we tried to solve the problem of optimization of feature selection by using natural processes of whale optimization and flower pollination algorithms, and on the other hand, we used opposition-based learning method to ensure the convergence speed and accuracy of the proposed algorithm. In fact, in the proposed method, the whale optimization algorithm uses the bait siege process, bubble attack method and bait search, creates solutions in its search space and tries to improve the solutions to the feature selection problem, and along with this algorithm, Flower pollination algorithm with two national and local search processes improves the solution of the problem selection feature in contrasting solutions with the whale optimization algorithm. In fact, we used both search space solutions and contrasting search space solutions, all possible solutions to the feature selection problem. To evaluate the performance of the proposed algorithm, experiments are performed in two stages. In the first phase, experiments were performed on 10 sets of data selection features from the UCI data repository. In the second step, we tried to test the performance of the proposed algorithm by detecting spam emails. The results obtained from the first step show that the proposed algorithm, by running on 10 UCI data sets, has been able to be more successful in terms of average selection size and classification accuracy than other basic meta-heuristic algorithms. Also, the results obtained from the second step show that the proposed algorithm has been able to perform spam emails more accurately than other similar algorithms in terms of accuracy by detecting spam emails.

Initial choice of Learning Rate is a key part of gradient based methods and has a great effect on the performance of the Deep Learning Model.This paper studies the behavior of multiple gradient based optimization algorithm which are commonly used in Deep Learning and compare their performance on various learning rate. As observed popular choice of optimization algorithms are highly sensitive to various choice of learning rates. Our goal is to find which optimizer has an edge over others for a specific setting. We look at two datasets namely MNIST and CIFAR10 for benchmarking. The results are quite surprising, and it will help us to choose a learning rate more efficiently.

The purpose of this paper is to develop a theoretical predictive model for LNG shipping routes selection process. Strategic decisions about shipping costs could be improved if a deeper knowledge about products economic value is provided. Developments made on the extraction and industrial processes related to this fossil fuel are driving the natural gas sector towards a unique globalised market. Moreover, data analytics applications as well as machine learning are topics presented as perfect catalysers for achieving an unprecedented natural gas globalised market. Additionally, this paper aims at showing the state of the art of new techniques used in transportation engineering that might have synergies with other industries (eg. commodities cost reduction, energy supply…). Finally, this paper aims to provide foundation for further research and development using more sophisticated data and algorithms that will help to close the gap between theoretical and practical scope of this techniques.

With the ongoing fifth-generation cellular network (5G) deployment, electromagnetic field exposure has become a critical concern. However, measurements are scarce, and accurate electromagnetic field reconstruction in a geographic region remains challenging. This work proposes a conditional Generative Adversarial Network to address this issue. The main objective is to reconstruct the electromagnetic field exposure map accurately according to the environment’s topology from a few sensors located in an outdoor urban environment. The model is trained to learn and estimate the propagation characteristics of the electromagnetic field according to the topology of a given environment. In addition, the conditional Generative Adversarial Network based electromagnetic field mapping is compared with simple kriging. Results show that the proposed method produces accurate estimates and is a promising solution for exposure map reconstruction.

Regulatory T cells (Tregs) are major drivers behind immunosuppressive mechanisms and present a major hurdle for cancer therapy. Tregs are characterized by high expression of CD25, which is a potentially valuable target for Treg depletion to alleviate immune suppression. The preclinical anti-CD25 (αCD25) antibody, clone PC-61, has met with modest anti-tumor activity, due to its capacity to clear Tregs from circulation and lymph nodes but not those that reside in the tumor. Optimization of the Fc domain of this antibody clone has been shown to enhance intratumoral Treg depletion capacity. Here, we generated a stable cell line that produces optimized recombinant Treg depleting antibodies. A genome engineering strategy in which CRISPR-Cas9 was combined with homology directed repair (CRISPR-HDR) was utilized to optimize the Fc domain of the hybridoma PC-61 for effector functions by switching it from the original rat IgG1 to a mouse IgG2a isotype. In a syngeneic tumor mouse model the resulting αCD25-m2a antibody mediated effective depletion of tumor resident Tregs leading to a high effector T cell (Teff) to Treg ratio. Moreover, combination of the αCD25-m2a with αPD-L1 treatment augmented tumor eradication in mice, demonstrating the potential for αCD25 as a cancer immunotherapy.

The enormous increase in the volume of Earth Observations (EOs) has provided the scientific community with unprecedented temporal, spatial, and spectral information. However, this increase in the volume of EOs has not yet resulted in proportional progress with our ability to forecast agricultural systems.This study examines the applicability of EOs obtained from Sentinel2 and Landsat8 for constraining the APSIM-Maize model parameters. We leveraged leaf area index (LAI) retrieved from Sentinel2 and Landsat8 NDVI to constrain a series of APSIM-Maize model parameters in three different Bayesian multi-criteria optimization frameworks across 13 different sites across the U.S Midwest. A time variant sensitivity analysis was performed to identify the most influential parameters driving the LAI estimates in APSIM-Maize model. Then surrogate models were develop using random samples taken from the parameter space using Latin hypercube sampling to emulate APSIM’s behavior in simulating NDVI and LAI at all sites. Site-level, global and hierarchical Bayesian optimization models were then developed using the site-level emulators to simultaneously constrain all parameters and estimate the site to site variability in crop parameters. For within sample predictions, site-level optimization showed the largest predictive uncertainty around LAI and crop yield, whereas the global optimization showed the most constraint predictions for these variables. Lowest RMSE for within sample yield prediction was found for hierarchical optimization scheme (1423 Kg ha−1) while the largest RMSE was found for site-level (1494 Kg ha−1). In out-of-sample predictions within the spatio-temporal extent of the training sites, global optimization showed lower RMSE (1627 Kg ha−1) compared to the hierarchical approach (1822 Kg ha−1) across 90 independent sites in the U.S Midwest. On comparison between these two optimization schemes across another 242 independent sites outside the spatio-temporal extent of the training sites, global optimization also showed substantially lower RMSE (1554 Kg ha−1) as compared to the hierarchical approach (2532 Kg ha−1). Overall, EOs demonstrated their real use case for constraining process-based crop models and showed comparable results to model calibration exercises using only field measurements.

The concept of distributed generation has made photovoltaic an integral source of energy in smart grid systems, especially in peer-to-peer energy trading frameworks that exploit excess power to fulfill the energy requirements of consumers in cost-efficient and eco-friendly manner. It is believed that P2P energy trading will dominate a significant portion of research in forthcoming power generation systems due to the excessive rise of energy demands across the globe. Despite a plethora of studies on energy optimization solutions in P2P trading, minimizing nanogrid energy trading cost and efficient energy sharing between consumers and prosumers are deemed among the challenging problems. This study overcomes essential issues overlooked by the contemporary P2P energy trading models by introducing a predictive optimization-oriented nanogrid energy trading model. The proposed study encompasses two stages: (1) predictive optimization model which harnesses BD-LSTM-based forecasted energy parameters (energy load, energy consumption, and PV generation) that are later incorporated in PSO-enabled objective function to reduce nanogrid trading cost, (2) optimal energy sharing plan is devised to decide the role of nanogrids as prosumers or consumers by emphasizing the use of PV-produced energy. The proposed model is validated on the case study containing nanogrid houses data. The simulation provides detailed experiments by comparing the energy demand and response using the proposed energy sharing model. The outcomes yield that the energy sharing plan holds a significant potential to fulfill maximum energy requirements of nanogrid house in P2P cluster and significantly reduces the energy cost compared to grid.

Water distribution networks are vital infrastructure, needed for providing consumers with sufficient water of appropriate quality. The cost of construction, operation, and maintenance of such networks is extremely large. The problem of optimization of a water distribution network is governed by the type of water distribution network and the size of pipelines placed in the distribution network. This problem of the optimal diameter allocation of pipes in a distribution network has been heavily researched over the past few decades. This study describes the development of a computer program, ‘Smart Optimization Program for Water Distribution Networks’ (SOP–WDN), which applies Genetic Algorithm to the problem of the least-cost design of water distribution networks. SOP–WDN demonstrates the application of an evolutionary optimization technique, Genetic Algorithm, linked with a hydraulic simulation solver EPANET, for the optimal design of water distribution networks. The developed program was applied to three benchmark water distribution network optimization problems and produced consistently good results. SOP–WDN can be utilized as a tool for guiding engineers during the design and rehabilitation of water distribution pipelines.

Innovative practices in irrigation systems can bring improvements in terms of economic efficiency and in the same time can reduce environmental impact. Investment in high tech technologies frequently involves additional costs, but an efficient water management can increase the lifetime of the equipment. The main objective of this article is to reduce the energy consumption by one thousand cubic meters pumped and automatically to increase the economic efficiency of the pumping groups. This paper develops a new operating algorithm that ensures the operation of the pumping group at safe operating intervals and in the same time identifies the equivalent pump operating points for the entire flow range and pumping height of the pumping group. This methodology is based on the principles of an Expert System to perform the optimization process of the energy consumption in pumping groups. The resulting methodology avoids the combinatorial explosion of the solutions to be analyzed and determines the point of maximum efficiency without violation of any of the system constraints under any operating condition. The proposed methodology is tested on an irrigation system that includes a pumping group with 5 pumps, showing its effectiveness in obtaining the optimal solution with a relatively low computational burden.

Applications in high-performance computing (HPC) may not use all available computational resources, leaving some of them underutilized. By co-scheduling, i.e. running more than one application on the same computational node, it is possible to improve resource utilization and overall throughput. Some applications may have conflicting requirements on resources and co-scheduling may cause performance degradation, so it is important to take it into account in scheduling decisions. In this paper, we formalized co-scheduling problem and proposed multiple scheduling strategies to solve it: an optimal strategy, an online strategy and heuristic strategies. These strategies vary in terms of the optimality of the solution they produce and a priori information about the system they require. We showed theoretically that the online strategy provides schedules with a competitive ratio that has a constant upper limit. This allowed us to solve the co-scheduling problem using heuristic strategies that approximate this online strategy. Numerical simulations showed how heuristic strategies compare to the optimal strategy for different input systems. We proposed a method for measuring input parameters of the model in practice and evaluated this method on HPC benchmark applications. We showed high accuracy of measurement method, which allows to apply proposed scheduling strategies in scheduler implementation.

In this paper, we implement a new method binary Particle Swarm Optimization (PSO) for solving the kidney exchange problem, which will improve the future decisions of kidney exchange programs. Because using a kidney exchange, we can help incompatible patient-donor couples to swap donors to receive a compatible kidney. Kidney paired donation programs provide an innovative approach for increasing the number of available kidneys. Further, we implementing binary particle swarm optimization in parallel with MATLAB with one, two, three and four threads and from the computations point of view, the authors compare the performance to reduce the running time for kidney exchange to match patients as fast as possible to help clinicians. Moreover, implementing binary particle swarm optimization in solving the kidney exchange problem is an effective method. The obtained results indicate that binary PSO outperforms other stochastic-based methods such as genetic algorithm, ant lion optimization, and efficient the number of resulting exchanges.

Patch antennas are compact, less complex, planar structures and therefore, widely used in small satellite missions for telecommand, data link, and intersatellite link, particularly in S- band and X- band. Improved performance of these patch antennas in terms of gain and compactness will di-rectly affect the communication efficiency of small satellite missions. Especially the coming IoT (Internet of Things) constellations require high gain and efficient antenna arrays. An optimization of single patch antenna elements is an important cornerstone for the missions. Therefore, the ef-fects of various antenna enhancement techniques, such as slotted ground plane, resistor and ca-pacitor integration, parasitic patch elements, are analyzed. These techniques were applied on a rectangular patch antenna with parameter variation to identify the optimal performances with respect to bandwidth, operating frequency, gain, polarization, and power flow. Finally, the techniques were combined to obtain an optimized antenna in terms of gain and compactness. The results were compared to a slotted reference antenna. For the scenario of a 2.4 GHz patch antenna, a gain optimization of 27 % (from 7.09 to 8.14 dBi) or size reduction of 52 % (from 96.04 to 46.2 cm²) could be achieved. Overall, our study revealed an effective way to increase the patch antenna performance, which can directly contribute to more efficient communication links and design of antenna arrays.

Single cell proteins are the dead dried cells of microorganisms or purified protein isolated from microorganism’s cell culture, used as a food supplement to humans’ food and animals feed. World suffer from malnutrition particularly developing countries, due to rapid increase in population, increased the demand for protein and nutrients requirement. Bacteria is potential microorganism for SCP production due to high protein content, fast generation time, bio-active secondary metabolites production and can grow on various substrates. Actinobacteria species and strain have capability to produce biological active compounds, produced about two-thirds of antibiotics available in the market, actively used as antibiotics, antiprotozoal, antifungal, antiviral, anticancer, anticholesterol, antihelminth and immunosuppressant. Actinomycetes can be used as probiotic as well as single cell protein that will deal with antibiotic as well as protein source.

Feature selection is one of the main data preprocessing steps in machine learning. Its goal is to reduce the number of features by removing extra and noisy features. Feature selection methods must consider the accuracy of classification algorithms while performing feature reduction on a dataset. Meta-heuristic algorithms are the most successful and promising methods for solving this issue. The symbiotic organisms search algorithm is one of the successful meta-heuristic algorithms which is inspired by the interaction of organisms in the nature called Parasitism Commensalism Mutualism. In this paper, three engulfing binary methods based on the symbiotic organisms search algorithm are presented for solving the feature selection problem. In the first and second methods, several S-shaped and V-shaped transfer functions are used for binarizing the symbiotic organisms search algorithm, respectively. These methods are called BSOSS and BSOSV. In the third method, two new operators called BMP and BCP are presented for binarizing the symbiotic organisms search algorithm. This method is called EBSOS. The third approach presents an advanced binary version of the coexistence search algorithm with two new operators, BMP and BCP, to solve the feature selection problem, named EBSOS. The proposed methods are run on 18 standard UCI datasets and compared to base and important meta-heuristic algorithms. The test results show that the EBSOS method has the best performance among the three proposed approaches for binarization of the coexistence search algorithm. Finally, the proposed EBSOS approach was compared to other meta-heuristic methods including the genetic algorithm, binary bat algorithm, binary particle swarm algorithm, binary flower pollination algorithm, binary grey wolf algorithm, binary dragonfly algorithm, and binary chaotic crow search algorithm. The results of different experiments showed that the proposed EBSOS approach has better performance compared to other methods in terms of feature count and accuracy criteria. Furthermore, the proposed EBSOS approach was practically evaluated on spam email detection in particular. The results of this experiment also verified the performance of the proposed EBSOS approach. In addition, the proposed EBSOS approach is particularly combined with the classifiers including SVM, KNN, NB and MLP to evaluate this method performance in the detection of spam emails. The obtained results showed that the proposed EBSOS approach has significantly improved the accuracy and speed of all the classifiers in spam email detection.

Application of solid catalysts synthesized from agricultural wastes provides an environmentally benign and low-cost process route to the synthesis of biodiesel. An ash containing equal mixture of cocoa pod husk, plantain peel and kola nut pod husk ashes (CPK) which was obtained by open combustion of each biomass in air and calcined at 500 oC for 4 h. The calcined CPK ash was characterized to determine its catalytic potential. Two-level transesterification technique was used to synthesize biodiesel using the developed catalyst. The process parameters involved were optimized for the microwave-aided transesterification of a blend of honne, rubber seed and neem oils in volumetric ratio 20:20:60, respectively. The study showed that ash derived from combination of various biomass wastes provides a catalyst which consists all necessary catalytic ingredients in their relative abundance. The calcined CPK consists of 47.67% of potassium, 5.56% calcium and 4.21% magnesium attesting to its heterogenous status. The physisorption isotherms reveals that it was dominantly mesoporous in structure made up of nanoparticles. Maximum of 98.45 wt.% biodiesel was obtained through MeOH:oil blend of 12:1, CPK concentration of 1.158 wt.% and reaction time of 6 min under microwave irradiation. Quality of the synthesized biodiesel satisfied the requirements stipulated by standard specifications. Thus, this work demonstrates that blend of agrowastes and mixture of non-edible oils could be used to synthesize quality and sustainable biodiesel that can replace fossil diesel.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

The current work investigates how adding a battery of optimal capacity to a grid-connected photovoltaic (PV) system can improve its economic feasibility. Also, the effect of different parameters on the feasibility of the PV system was evaluated. The OBC was determined for different saving targets of the annual electricity consumption of the chosen building. For this aim, real electricity consumption data of a residential building in Landskrona, Sweden, was used as energy consumption profile. Solar World SW325XL, which is a monocrystalline solar panel, was selected as PV panels. The calculations were performed under the metrological and economic conditions of southern Sweden. Different working parameters (WP)were considered (prices of the battery, feed-in tariffs, and saving targets). The performed calculations show that the optimal battery capacity (OBC), in which the payback time (PBT) of the system is maximized, strongly depends on the WP. The proper selection of the battery can considerably increase the economic feasibility of the PV system in southern Sweden. However, in some cases, using battery can have a negative impact on the PBT of the system. The results show that the electricity price, the module price, the inverter price, and the inverter lifetime have the highest effect on the PBT.

The present work aims at the comprehensive application of stochastic and optimization tools with the support of Information and Communication Technologies (ICT) through a case study in a logistics process for electronic goods; simulation and Response Surface Methodology (RSM) are applied for this purpose. The problem to be evaluated is to define an optimal distribution cost for products shipped to wholesale customers located in different cities in Mexico from a manufacturing plant in Tijuana, Mexico. The factors under study are the product allocation for each distribution center, finished good inventory level and on time deliveries, which are supposed to be significant to get the objective. The methodology applied for this problem considers the design of a discrete event simulation model to represent virtually the real life of logistics process, which is considered a complex system due to different activities are interrelated to carry it out. This model is used to execute the different experiments proposed by the RSM. The results obtained from simulation model were analyzed with the RSM to define the mathematical model that allows identifying the parameters of the factors in order to optimize the process. The findings prove how the ICT facilitate the application of stochastic tools with the purpose of process optimization.

Several optimization models of irreversible reverse cycle machines have been developed based on different optimization criteria in the literature, most of them using linear heat transfer laws at the source and sink. This raises the issue how close to actual operation conditions they are, since the heat transfer law on the phase-change processes is dependent on ΔT3. This paper addresses this issue by proposing a general model for study and optimization of thermal machines with two heat reservoirs applied to a Carnot-like refrigerator, with non-linear heat transfer laws and internal and external irreversibility. The optimization was performed using First and Second Law of Thermodynamics and Lagrange multipliers method. Thus, several constraints were imposed to the system, also different objective functions were considered, allowing finding the optimum operating conditions, as well as the limited variation ranges of the system parameters. Results show that the nature of the heat transfer laws affects the optimum values of system parameters for obtaining maximum performances and also their magnitude. Sensitivity studies with respect to system several parameters are presented. The results contribute to the understanding of the system limits in operation under different constraints and allow choosing the most convenient variables in given circumstances.

Forming a clustered network structure has been proposed as a solution to increase network performance, scalability, stability and manageability in an ad hoc network. A good clustering algorithm aims to select cluster heads among available nodes so that a number of specific constraints are satisfied; thus the cluster head selection problem is a multiobjective optimization problem. This paper proposes an algorithm on the basis of ant colony optimization (ACO) to be used to solve this problem. The proposed algorithm is a simple, one hop cluster formation algorithm, to form a clustered structure with the minimum number of clusters. The centralized ACO-based clustering algorithm is evaluated and compared with other clustering algorithms in ad hoc networks in terms of cluster density.

In recent years, integration of electric vehicles (EVs) has increased dramatically due to their lower carbon emissions and reduced fossil fuel dependency. However, charging EVs could have significant impacts on the electrical grid. One promising method for mitigating these impacts is the use of renewable energy systems. Renewable energy systems can also be useful for charging EVs where there is no local grid. This paper proposes a new strategy for designing a renewable energy charging station consisting of wind turbines, a photovoltaic system, and an energy storage system to avoid the use of diesel generators in remote communities. The objective function is considered to be the minimization of the total net present cost, including energy production, components setup, and financial viability. The proposed approach, using stochastic modeling, can also guarantee profitable operation of EVs and reasonable effects on renewable energy sizing, narrowing the gap between real-life daily operation patterns and the design stage. The proposed strategy should enhance the efficiency of conventional EV charging stations. The key point of this study is the efficient use of excess electricity. The infrastructure of the charging station is optimized and modeled.