Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

In this study, we considered the structural stability, electronic properties, and phonon dispersion of the cubic (c-ZrO₂), tetragonal (t-ZrO₂), and monoclinic (m-ZrO₂) phases of ZrO₂. We found that the monoclinic phase of zirconium dioxide is the most stable among the three phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic properties. The smallest negative modes were found for m-ZrO₂. Our analysis of the electronic properties showed that during the m–t phase transformation of ZrO₂, the Fermi level first shifts by 0.125 eV toward higher energies and then decreases by 0.08 eV in the t–c cross-section. The band gaps for c-ZrO₂, t-ZrO₂, and m-ZrO₂ are 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35, and 16.15 mol. %Y₂O₃ onto the m-ZrO₂ structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO₂ and an increase in its defectiveness. The doping-induced and concentration-dependent phase transition of zirconium dioxide under the influence of yttrium oxide was studied, after which the position of the Fermi level changes and the energy gap decreases. It has been established that, not only for pure systems but including those doped with Y₂O₃, the main contribution to the formation of the conduction band is made by the p-states of electrons. The t-ZrO₂ (101) and t-YSZ (101) surface models were selected as optimal surfaces for water adsorption based on a comparison of their surface energies. An analysis of the mechanism of water adsorption on the surface of t-ZrO₂ (101) and t-YSZ (101) showed that H₂O on unstabilized t-ZrO₂ (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom. The calculations showed that ab initio research methods are capable of describing the mechanism of phase transitions of materials under the influence of alloying. That is, by optimizing the parameters of DFT calculations, it is possible to observe the effects of doping on other physical and chemical properties of materials, which are still beyond the scope of quantum chemical modeling. The obtained results complement the database of research works carried out in the field of the application of biocompatible zirconium dioxide crystals and ceramics in green energy generation and can be used in designing humidity-to-electricity converters and creating solid oxide fuel cells based on ZrO₂.

The goal of this paper is to fabricate innovative diaphragm headphones using graphene oxide paper (GOP) and GOP/epoxy nanocomposites (GOPC). Initially, graphene oxide suspension is fabricated, and the vacuum filtration method is adopted to make GOP. Then vacuum bag molding is used to fabricate GOPC from GOP. Hot pressing and associated molds are adopted to fabricate line-indented (GOPC-L) or curve-indented patterns (GOPC-C) on the GOPC. The performance of one kind of GOP and three kinds of GOPC diaphragm headphones is analyzed based on their sound pressure level (SPL) curves achieved by the Soundcheck measurement system. There are four important processing parameters that will influence the performance of the diaphragm, including material type GOP versus GOPC, indented pattern type, sonication time on suspension, and graphene weight fraction in suspension. Compliances of various diaphragms are measured by the Klippel LPM laser measurement system. The results indicate that effects of sonication time and graphene weight fraction on SPL of GOP and GOPC headphones are in reverse, and this is associated with their difference on compliance (modulus), mass, damping ratio, and microstructure uniformity. Either GOPC-L or GOPC-C seems to improve the microstructure of the GOPC, and leads to better SPL performance. The correlation between the previous four factors and SPLs of four kinds of diaphragm headphones is proposed by using scanning electron microscope (SEM) to examine the microstructure of these diaphragms.

In the Neighborhood Area Network (NAN), the Advanced Metering Infrastructure (AMI) enables a bidirectional connection between the Smart Meter (SM) and the Data Concentrator (DC). Sensors, such as smart meter node or Radio Frequency transceiver, play a crucial role in collecting and transmitting data from meters to central unit for advanced monitoring, management, and analysis of energy consumption. Wired and wireless communication technologies can be used to implement the AMI-NAN. This paper delves into a novel approach for optimizing the choice of communication medium, Radio Frequency (RF) or Power-Line Communication (PLC), between the SM and DC in the context of AMI-NAN. The authors methodically select the specific technologies, RF and NB-PLC (Narrow Band Power-Line Communication), and meticulously characterize their attributes. Then, a comparative analysis spanning rural, urban, and industrial settings is conducted to evaluate the proposed method. The overall reliability performance of the AMI-NAN system requires a Packet Error Rate (PER) lower than 10%. To this end, a comprehensive methodology is introduced to assess and enhance the reliability of NB-PLC and RF for AMI-NAN applications. Simulation results demonstrate that wireless communication is the optimal choice for the rural scenario, especially for Signal to Noise Ratio (SNR) lower than 25 dB. However, in urban environments characterized by higher SNR values and moderately dense networks, NB-PLC gains prominence. In denser networks, it outperforms wireless communication, exhibiting a remarkable 10 dB gain for a bit error rate (BER) of 10-3. Moreover, in industrial zones characterized by intricate network topologies and non-linear loads, the powerline channel emerges as the optimal choice for data transmission, affording a gain surpassing 20 dB.

To supply stable and high-quality power according to the advancement of industrial growth, electric power companies have performed maintenance of power facilities using various meth-ods. In the case of domestic power distribution facilities, there are limitations in performing di-agnostic management on all facilities owing to the large number of facilities; therefore, old fa-cilities are managed by the health index assessment method. The health index assessment com-prises only facility operation data and external environmental data and is managed only for four types of distribution facilities, including overhead/underground transformers and switchgear. In the case of extra high–voltage overhead wires, there is no standard for old replacement, despite the large number of wires, such as transformers and switchgear, and the large ripple effect of power failure in the event of a power outage. Therefore, in this paper, a health index assessment methodology for extra-high voltage overhead cables was developed. In this paper, we devel-oped an economic health index assessment methodology that additionally considers risk cost, which is different from the existing health index assessment method that uses only operational data and external environmental data to determine facility performance evaluation and aging replacement criteria. Using the health index assessment methodology developed in this paper, it is possible to expect a reduction in facility operating costs and investment costs from the per-spective of electric power companies through the replacement of old extra-high voltage over-head cables. In addition, from the perspective of consumers, it is expected to increase power re-liability and reduce the ripple effect of failure by preferentially replacing equipment with a high probability of failure.

The extraction of roof feature lines is an important foundation for realizing large-scale and batch 3D modeling. However, the current traditional point cloud segmentation algorithms do not have satisfactory results in extracting roof feature lines of Chinese traditional residential buildings. In this paper, taking Jingping Village in Western Hunan as an example, we propose a method that combines multiple algorithms based on slope segmentation of roof patches to extract feature lines. Firstly, VDVI and CSF algorithms are used to extract the building and roof point cloud based on the MVS point cloud. Secondly, according to roof features, village buildings are classified, and 3D roof point cloud is projected into 2D regular grid data. Finally, the roof slope is segmented via slope direction, and internal and external feature lines are obtained after refinement through Canny edge detection and Hough straight line detection. Results reveal that this method effectively extracts feature lines of low-building roofs in traditional villages, with slope-based roof surface segmentation accuracy surpassing 99.6%. This method significantly outperforms the RANSAC algorithm and region segmentation algorithm.

This paper reports aligned activities to promote energy and resource-efficient construction practice in Vietnam. First, the governance framework is introduced, including government decrees and technical standards. Then, a laboratory with building physics measurement technology is designed and partly set up at the local partner Vietnam Institute for Building Materials (VIBM), which can be used to determine the essential characteristic values required for the implementation of energy standards. The basis for the prioritization of the characteristic values are the requirements of the National technical regulation on energy efficient buildings of Vietnam – QCVN09:2017/BXD. Furthermore, basic characteristic values from international standards are described, which can also be used for calculations to optimize the energy consumption of buildings. In order to be able to carry out transient hygrothermal computer simulations, special characteristic values were also included. These are particularly useful for the research and development of new building materials and the evaluation of entire buildings in terms of thermal and moisture protection In order to communicate the material properties to the market and enable informed decision making by the stakeholders, a labeling system has been developed. Thereby, the practical means for implementing governance instruments are provided, and the related technical applications are supported.

The paper considers the issues of structural stability, electronic properties, and phonon dispersion of the cubic, tetragonal, and monoclinic phases of ZrO2. It was found that the monoclinic phase of zirconium dioxide is the most stable among the other two phases in terms of total energy, lowest enthalpy, highest entropy, and other thermodynamic values. The smallest negative modes were found for m-ZrO2. An analysis of the electronic properties showed that during the m–t phase transformation of ZrO2, the Fermi level first shifts by 0.125 eV towards higher energies, and then decreases by 0.08 eV in the t–c cross section. The band gap for c-ZrO2, t-ZrO2, and m-ZrO2 is 5.140 eV, 5.898 eV, and 5.288 eV, respectively. Calculations based on the analysis of the influence of doping 3.23, 6.67, 10.35 and 16.15 mol. %Y2O3 on the m-ZrO2 structure showed that the enthalpy of m-YSZ decreases linearly, which accompanies further stabilization of monoclinic ZrO2 and an increase in their defectiveness. In this case, the position of the Fermi level changes abruptly, and the energy gap decreases. It has been established that not only for pure systems, including those doped with Y2O3, the main contribution to the formation of the conduction band is made by the p-states of electrons. An analysis of the mechanism of water adsorption on the surface of t-ZrO2 (101) and t-YSZ (101) showed that H2O on unstabilized t-ZrO2 (101) is adsorbed dissociatively with an energy of -1.22 eV, as well as by the method of molecular chemisorption with an energy of -0.69 eV and the formation of a hydrogen bond with a bond length of 1.01 Å. In the case of t-YSZ (101), water is molecularly adsorbed onto the surface with an energy of -1.84 eV. Dissociative adsorption of water occurs at an energy of -1.23 eV, near the yttrium atom.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

Meals on Wheels (MoWs) provide access to daily meals and social contact to adults with care and support needs.MoWs could be essential for the increasing rates of an ageing population and adults living with complex needs in England, yet many do not know that the service exists. This study aimed to explore the perceptions of MoWs service users, and people who refer them to MoWs (‘referrers’), with accessing and setting up the service in England, and what information would be valued when considering accessing MoWs services.Semi-structured interviews were conducted in May-July 2022 with seven service users and 21 referrers, recruited from four MoWs providers across England. Data were analysed using thematic analysis. Participants indicated various pathways into the service, but referrers (family members) were more likely to be the ones enquiring about, and setting up, MoWs for service users. Once an enquiry about MoWs had been made, the service was perceived as straightforward to set up.However, existing preconceptions and stereotypes about the service (e.g. bringing to mind ‘school meals’, aimed solely at older adults) were perceived to act as barriers to accessing MoWs.Information that participants deemed important to have available when deciding on whether to access MoWs related to the meals (e.g. nutritional value, variety, need for any preparation, catering for individual needs), the specific services provided (e.g. wellbeing checks, daily social contact), the reliability and flexibility of delivery, and the cost of services. These findings could inform MoWs providers’ public awareness strategies about MoWs, in order to facilitate referrals to the service for adults with care and support needs.

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

Covariant integral quantization with rotational symmetry SO(3) is established for the quantum motion on this group manifold, or, alternatively, for Gabor signal analysis on this group. We revisit the action of the related (non-unitary) Weyl-Gabor operator on the Hilbert space of square integrable functions on SO(3) and disclose a set of various properties. By selecting weight functions on the corresponding discrete-continuous phase space, one derives related coherent states and Wigner transform.

In this paper, we consider a pursuit-evasion game of inertial players, where pursuer’s control is subject to integral constraint, and evader’s control is subject to geometric constraint. In the pursuit problem, the main tool is the strategy of parallel pursuit. Sufficient conditions are obtained for the solvability of pursuit-evasion problems. Also, the main lemma describing the monotonicity of an attainability domain of the evader is proved and an explicit analytical formula for this domain is given. As one of the important results of our paper, the Isaacs Life-line game is solved for a special case.

Influence of reaction time on silver nanoparticles-catalyzed oxidation of 3,3’,5,5’-tetramethylbenzidine (TMB) was evaluated via probing the oxidation process by recording the UV-Visible absorbance of the resulting colored products of TMB oxidation by hydrogen peroxide in the presence of silver nanoparticles as peroxides mimics. The time curve of the oxidation process was constructed, revealed that the concentration of the oxidation product was increased by increasing the reaction time and then levled off because the nanozyme active nodes were saturated after a certain reaction time and consequently the steady-state condition can be observed. The maximal activity of the silver nanozymes was achieved after a very short reaction time as short as 3.0 min and after this time, the color intensity of the oxidation products remained constant, revealing saturation of active nodes of nanoparticles with nanozyme-substrate.

Colorectal cancer is the third most common disease and the second most common cause of death in the world. The drug for second-line treatment depends on the drugs used in first-line treatment and biomarker status. As biomarkers, the RAS gene, BRAF gene, and dMMR/MSI-H, TMB-H, and HER2 statuses have been established in clinical practice, and the corresponding molecularly targeted therapeutic agents are selected based on biomarker status. Given the frequency of biomarkers, it is assumed that when patients move on to second-line treatment, an angiogenesis inhibitor is selected in many cases. For second-line treatment, three angiogenesis inhibitors, bevacizumab (BEV), ramucirumab (RAM), and aflibercept (AFL), are available, and one of them is combined with cytotoxic agents. These three angiogenesis inhibitors are known to inhibit angiogenesis through different mechanisms of action. Although no useful biomarkers are established for selecting angiogenesis inhibitors, previous biomarker studies have suggested that angiogenesis-related factors such as VEGF-A and VEGF-D might be predictors of therapeutic efficacy of angiogenesis inhibitors. These biomarkers are measured as protein levels in plasma and are considered to be hopeful biomarkers. We consider that the rationale for selecting among these three angiogenesis inhibitors should be clarified to benefit patients.

In a saline semi-isolated Lagoon on the Cape Zeleny (White Sea), the annual dynamics of the vertical hydrological structure, and the seasonal dynamics of phytoplankton were traced, including species composition, and vertical distribution, abundance, nutrition type,and biomass.293 species and supraspecific taxa of algae and cyanobacteria were found. Most of the identified species are marine, and 38 species are freshwater. Taxonomic composition changed in the Lagoon during the year. Dinoflagellates dominated in winter and early June; unidentified cocci and flagellates in July; diatoms, dinoflagellates and unidentified cells in August; dinoflagellates in September; and unidentified cocci and flagellates in October–November. The abundance of algae also changed in the Lagoon during the year. The integrated biomass in the water column varied from 0.01 g C/m2 in January to 0.78 g C/m2 in early September. According to the abiotic parameters, the water column of the Lagoon is subdivided into several zones with different conditions and corresponding phytoplankton communities. Similarity between the communities of different horizons was 32-46% in summer and 7% in winter. The chemocline layer was the most populous. Almost the entire year it contained a maximum of phytoplankton biomass, 1-2 orders of magnitude higher than that in the overlying horizons. Comparison phytoplankton in the lagoon and in the nearby sea area was carried out. Despite the connection between the Lagoon and the sea phytoplankton structure in the surface water layer in the Lagoon and in the sea differs significantly in composition, quantitative parameters, and seasonal dynamics. The similarity of the communities in the sea and the Lagoon never exceeded 50%. In terms of biomass, the Lagoon lags behind the sea until mid-summer, but, starting from August, it outnumbers it, and the phytoplankton development in the Lagoon lasts longer, until late autumn. The phytoplankton structure and dynamics in the Lagoon and the sea by 24.5% was related to the daylight, water salinity, oxygen content and pH, but did not depend on water T, underwater illuminance, and depth. Oxygen content and pH are defined by PhP activity. Salinity serves as a vector of the vertical sequence of ecological niches. The daylight length seems to be the crucial factor of the seasonal PhP dynamics in the semi-isolated coastal stratified lakes and lagoons.

The question of whether some neutrinos are tachyons remains unresolved although various evidence from cosmic ray and other data exists that the electron neutrino has an effective $m_\nu^2\approx -0.25 eV^2,$ which would require that one or more mass states is also tachyonic. In 2013 the $3+3$ model of the neutrino masses, which includes one tachyonic mass state, was proposed based on supernova SN 1987A neutrino data. Here we update evidence for tachyonic electron neutrinos and the $3+3$ model and discuss one test which could prove conclusive. The update of earlier evidence includes many new elements, including new data which makes the earlier cosmic ray evidence more robust, new results on cosmic ray composition, the ankle of the spectrum, leptonic cosmic ray data, and the statistical significance of finding the three large neutrino masses stipulated in the $3+3$ model. Barring a galactic supernova, which occur only around twice a century, a decisive test of the $3+3$ model could involve observing an extragalactic supernova neutrino burst, that is a cluster of neutrinos in a specific time window well beyond what chance would predict. Even though existing searches for such bursts have yielded only upper limits on the extragalactic supernova frequency within a certain distance, it is shown that the choice of a one-day window for possible neutrino clusters in time might be far more sensitive. A search using a one day time window could be done using existing data, and if a signal is found it would confirm the $3+3$ model. Of course, the absence of any day-long neutrino burst would not disprove the model, since it could mean only that the nearest supernova during the period when detectors were active was simply too far to be detected. Finally, apart from testing the 3 + 3 model, an alternative type of search is suggested using existing hadronic cosmic ray data (from the IceCube Collaboration) that might verify the tachyonic neutrino hypothesis.

Prior to clinical trials, preclinical testing of oncology drug candidates is performed by evaluating drug candidates with in vitro and in vivo platforms. For in vivo testing, animal models are used to evaluate the toxicity and efficacy of drug candidates. However, animal models often display poor translational results as many drugs that pass preclinical testing fail when tested in humans, with oncology drugs exhibiting especially poor acceptance rates. The FDA Modernization Act 2.0 promotes alternative preclinical testing techniques, presenting the opportunity to use higher complexity in vitro models as an alternative to in vivo testing, including 3D cell culture models. 3D tissue cultures address many of the shortcomings of 2D cultures by more closely replicating the tumour microenvironment through a combination of realistic drug diffusion, paracrine signaling, cellular phenotype, and vascularization that can better mimic native human tissue. This review will discuss the common forms of 3D cell culture, including cell spheroids, organoids, organs-on-a-chip, and 3D bioprinted tissues. Their advantages and limitations will be presented, aiming to discuss the use of these 3D models to accurately represent human tissue and as an alternative to animal testing. The use of 3D culture platforms for preclinical drug development is expected to accelerate as these platforms continue to improve in complexity, reliability, and translational predictivity.

To avoid the endless accumulation of QTL effects during pyramiding breeding, QTL epistasis plays a role of homeostasis. Four single-segment substitution lines with heading date QTLs were utilized to construct pyramiding materials with dual QTLs and triple QTLs, allowing for the estimation of QTL epistatic effects on heading date in rice. The epistatic components of dual QTL and triple QTL interactions were analyzed using data from three seasons of two years. All four QTLs can be considered as dominant loci, demonstrating superdominance. 75% of dual QTL interactions and 81.25% of triple QTL interactions obtained statistically significant results, reaffirming the prevalence of epistasis. Interactions of four QTLs with three positive effects and one negative effect generated 62.5% negative dual QTL epistatic effects and 57.7% positive triple QTL epistatic effects, forming the balance relationship “positive-negative-positive”. In fact, QTL effects were consistently partially neutralized by mixed QTL epistatic effects so as to control the infinite accumulation of QTL effects. QTL epistasis plays a role of homeostasis on heading date in rice. However, there were two exceptions. The directions of OsMADS50 and Hd3a-2 effects were consistently aligned with those of their mixed epistases, suggesting that the QTL or gene could be employed in pyramiding breeding with different objectives. This study elucidated the mechanism of epistatic interactions among four QTLs and provided valuable genetic resources for improving heading date in rice.

For a linear ordinary differential equation (ODE in short) of the third order, results are presented that supplement the theory of conjugate points and extremal solutions by W. Leighton, Z. Nehari, M. Hanan. It is especially noted the sensitivity of solutions to the initial data, which makes their numerical study difficult. Similar results were obtained for the third-order nonlinear equations of the Emden-Fowler type.

Analytical chemistry applied to medical and diagnostic analysis, recently focused on the development of cost-effective biosensors able to monitor the health status or to assess the level of specific biomarkers that can be indicative for several diseases. The improvement of technologies relating to the possibility of non-invasive sampling of biological fluids, as well as sensors for the detection of analytical signals and the computational capabilities of the systems routinely employed in everyday life (e.g. smartphones, computers, etc.), make the complete integration of self-standing analytical devices more accessible. This review aims to discuss the biosensors that have been proposed in the last 5 years focusing on two principal detecting approaches, optical and electrochemical, which have been employed for quantifying different kind of target analytes reaching detection limits below the clinical sample levels required. These detection principles applied to Point-of-care (POC) devices, have been extensively reported in literature and even the limited examples found on the market are based on these strategies. This work will show the latest innovations considering the integration of optical and electrochemical detection with the most commonly reported analytical platforms for POC applications such as paper-based or wearable and implantable devices.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

This work focused on proposing a plan for improvement and control of the customer service process in a customer service center, based on a waiting line analysis where it describes all the elements that interact in the system and a statistical analysis of processes to define the state in which it operates. Subsequently, the simulation of processes is applied to represent the system studied, and with it, to be able to evaluate different strategies for improvement and increase in productivity. The following strategies were evaluated: correction of the instability of customer service processes, establishment of new specification limits according to the promise of value to be fulfilled to customers, human resource management, administrative technical support. Finally, with the results obtained from the simulation of the system, the improvement and productivity increase plan is planned according to the DMAMC (Define, Measure, Analyze, Improve, Control, or DMAIC) continuous improvement cycle established in six sigma

To address the problem of limited fault diagnosis accuracy in oil-immersed on-load tap changers (OLTC), this paper introduces a novel fault diagnosis method that combines the analysis of mechanical vibration signals and high-frequency current signals. The proposed approach aims to enhance the accuracy of fault diagnosis. To begin, an experimental platform is constructed to simulate the OLTC contact. Mechanical vibration signals and high-frequency current signals are collected from the testing platform under various operating states. These signals are then subjected to wavelet packet transform for denoising, followed by correlation analysis to capture the relationship between signals in different states. Based on these preliminary steps, the features of the signals are extracted and analyzed using ensemble empirical mode decomposition and the Hilbert-Huang transform. Subsequently, a support vector machine (SVM) is employed to analyze both the mechanical vibration signal and high-frequency current signal, enabling the classification of the OLTC contact state. The results demonstrate that the combination of characteristic analysis of mechanical vibration signals and high-frequency current signals provides a more comprehensive reflection of the actual OLTC contact state under different conditions. Through the SVM classification, the error between the predicted values and real values of the two types of signals remains below 10%, validating the efficiency and feasibility of the proposed method for fault diagnosis of OLTC contacts. These research findings serve as a reliable foundation for the diagnosis of operational states of on-site oil-immersed on-load tap changers, offering valuable insights for practical applications.

In this work, we present an analytical model of dynamic power losses for enhancement-mode AlGaN/GaN high-electron-mobility transistor power devices (eGaN HEMTs). To build this new model, the dynamic on-resistance (Rdson) is first accurately extracted by our ex-traction circuit based on a double-diode isolation (DDI) method for a high operating frequency up to 1 MHz and a large drain voltage up to 600 V, thus the unique problem of an increase in the dynamic Rdson is presented. Then the impact of the current operation mode on the on/off transi-tion time is evaluated by a dual-pulse-current-mode test (DPCT) which including a discontinu-ous conduction mode (DCM) and a continuous conduction mode (CCM), thus the transition time is revised for different current mode. Afterward the discrepancy between the drain current and the real channel current is qualitative investigated by an external shunt capacitance (ESC) meth-od, thus the losses due to device parasitic capacitance are also taken into account. After these improvements, the dynamic model will be more compatible for eGaN HEMTs. Finally, the dynamic power losses calculated by this model are verified to be in good agreement with experimental results. Based on this model, we propose a superior solution with qua-si-resonant mode (QRM) to achieve lossless switching and accelerate switching speed.

Oncological changes in the prostate are a common cause of death among elderly men. Malignant cells are difficult to identify at early stages, which are asymptomatic. The patient often seeks medical assistance when the disease has already progressed, and the treatment is less effective. Early diagnosis of prostate cancer (PC) is thus one of the priority tasks of modern urology and healthcare in general. The aim of this study is the detection of microRNAs (miRNAs), which are known to be associated with PC. The detection of the target miRNAs in human plasma samples has been performed with a nanoribbon biosensor system, which was based on "silicon-on-insulator" structures (SOI-NR biosensor). In order to provide biospecific detection of the target miRNAs, the surface of individual nanoribbons has been modified with DNA oligonucleotide probes (oDNA probes), whose nucleotide sequences were complementary to those of the target miRNAs. The high detection sensitivity has been demonstrated with the use of model oDNAs, which are complementary to nanoribbon-immobilized oDNA probes, in buffer solutions. The sensitivity threshold was 1.1 × 10^-17 M. The successful detection of target miRNAs, isolated from real plasma samples of PC patients, has also been demonstrated. We believe that the development of highly sensitive nanotechnology-based biosensors for PC markers is a step towards personalized medicine.

The mechanical effects of membrane compositional inhomogeneities are analyzed in a process analogous of neck formation in cellular membranes. We cast on the Canham-Helfrich model of fluid membranes with both the spontaneous curvature and the surface tension being non-homogeneous functions along the cell membrane. The inhomogeneous distribution is determined by the equilibrium mechanical equations and the boundary conditions as considered in the axisymmetric setting compatible with the necking process. To establish the role played by mechanical inhomogeneity, we focus on the catenoid, a surface of zero mean curvature. Analytic solutions are shown to exist for the spontaneous curvature and the constrictive forces in terms of the border-radii. Our theoretical analysis shows that the inhomogeneous distribution of spontaneous curvature in a mosaic-like neck constrictional forces potentially contributing to the membrane scission under minimized work in living cells.

Globally, gastric cancer is a major cause of cancer mortality, with a 5-year survival rate of 32% for locally advanced and metastatic gastric cancer. This systematic literature review summarized the clinical, safety, and humanistic outcomes associated with systemic regimens given as first line therapy for locally advanced and metastatic gastric cancer. The search included articles published in English in PubMed, Embase, Web of Science, Cochrane Central Register of Controlled Trials, and the American Society of Clinical Oncology meeting library, from inception to April 2022. Phase II and III randomized controlled trials conducted among western populations diagnosed with stage III and IV locally advanced and metastatic gastric cancer were included. Two investigators independently reviewed the studies, conducted data extraction, and assessed risk of bias in accordance with PRISMA guidelines. Twenty-four randomized controlled trials totaling 8,705 patients were included. Median overall survival ranged from 5.0-13.1 months, median progression-free survival ranged from 2.0-7.7 months, and objective response ranged from 13.0-64.1%. Two studies reported higher quality of life outcomes. Grade 3 and 4 adverse events were reported in most studies. Improvement in clinical outcomes can be seen in recently published randomized controlled trials for locally advanced and metastatic gastric cancer.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land

The research is focusing on analyzing the concentrations of particulate matter (PM) next to a highly congested road section, with 39,900 as a maximum number of vehicles per 24 h, in the vicinity of Timisoara, Romania. Concentrations have been measured in multiple episodes using two different measurement methods, gravimetric and dynamic light scattering, showing a disperse range of PM concentrations. Presence of metal particles in the samples have been analyzed using an electron microscope. Additionally, impact on human health is described by evaluating results for inhalable, thoracic, and alveolar sized particles.

This paper sheds light on how crisis management affects post-disaster re-covery. Based on the study of the management of a major environmental disaster, hurricane IRMA, we consider how post-disaster recovery is impacted by crisis management strategies. The perspectives of local stakeholders from the islands of St Martin and St Barthélémy will be shared. We analyze how territories exposed to the same natural phenomena have different outcomes and consider some of the possible reasons. This study reveals underlying risk drivers, to address governance reorganization with a view to better managing socio-economic recovery.

Aiming at the prediction of environmental vibrations induced by elevated high-speed railway, a machine-learning method is developed by combining random forest algorithm and Bayesian optimization, which using the dataset from on-site experiments . When it comes to achieving a rapid and effective prediction of environmental vibration, there is few research on com-parisons and verifications of different algorithms, and neither on parameter tuning and optimi-zation of machine learning algorithms. In this paper, a field experiment is firstly carried out to measure the ground vibrations caused by high-speed trains running on bridge, and then the en-vironmental vibration characteristics are analyzed in view of ground accelerations and weighted vibration levels. Subsequently, three machine-learning algorithms of linear regression, support vector machine and random forest are developed by using experimental database, and their prediction performance are discussed. Finally, two optimization models for the hyperparameter set of random forest algorithm are further compared. It turns out that the integrated random forest algorithm has higher accuracy in predicting environmental vibration than linear regression and support vector machine; the Bayesian optimization has excellent performance and high efficiency in achieving efficient and in-depth optimization of parameters, and can be combined with the RF machine learning algorithm to effectively predict the environmental vibrations induced by the high-speed railway.

Light Detection and Ranging (LiDAR) technology, a cutting-edge advancement in mobile applications, presents a myriad of compelling use cases, including enhancing low-light photography, capturing and sharing 3D images of fascinating objects, and elevating the overall augmented reality (AR) experience. However, its widespread adoption has been hindered by the prohibitive costs and substantial power consumption associated with its implementation. To surmount these obstacles, this paper proposes a low-power, low-cost, SPAD-based system-on-chip (SoC) which packages the microlens arrays (MLA) and incorporates with a light-weight RGB-guided sparse depth imaging completion neural network for 3D LiDAR imaging. The proposed SoC integrates an 8x8 Single-Photon Avalanche Detectors (SPADs) macro pixel array with time-to-digital converters (TDC) and charge pump, fabricated using a 180nm bipolar-CMOS-DMOS (BCD) process. A random MLA-based homogenizing diffuser efficiently transforms Gaussian beams into flat-topped beams with a 45° field of view (FOV), enabling flash projection at the transmitter. To further enhance resolution and broaden application possibilities, a lightweight neural network employing RGB-guided sparse depth complementation is proposed, enabling a substantial expansion of image resolution from 8x8 to quarter video graphics array level (QVGA; 256x256). Experimental results demonstrate the effectiveness and stability of the hardware encompassing the SoC and optical system, as well as the lightweight features and accuracy of the algorithmic neural network. This integrated state-of-the-art hardware-software solution offers a promising and inspiring foundation for developing consumer-level 3D imaging applications.

Existing research lacks studies that explore the impact of government fiscal support on the high-quality development of regional economy and society from the perspective of livelihood-based infrastructure construction. The investigation in this paper explores the economic and social effects of government fiscal support behavior from the perspective of livelihood infrastructure construction. On the basis of the TOPSIS-Entropy Method, this paper constructs an evaluation indicator that closely conforms to the denotation and requirements of high-quality development and then carries out empirical regressions in combination with government expenditure on people's livelihood to verify the theoretical hypothesis, whose transmission mechanism and moderating effect are further empirically tested. The results reveal that increasing government expenditure on people's livelihoods can effectively improve regional high-quality development, but the marginal improvement degree varies with different periods and locations. The mechanism test proves that the regional consumption level plays a significant part in the mediating effect, accounting for 24.27% of the total effect. Urbanization is also the critical impetus for regional high-quality development and positively moderates the promotion effect of people's livelihood fiscal expenditure. Our study presents a theoretical basis and policy inspiration for improving residents' quality of life and welfare level and improving people's livelihood in the midst of high-quality economic development.

Background: Exclusively breastfeeding your newborn while in the hospital is imperative for suc-cessful breastfeeding at home. This study will investigate if having a nurse on-site during rooming-in can enhance the proportion of exclusive breastfeeding. Methods: We carried out a prospective cohort study to assess exclusive breastfeeding in the first three months of life among two Neona-tology Units in Southern Italy with different hospital settings. The Ente Ecclesiastico Miulli of Ac-quaviva delle Fonti had on-site nurses available 24/7 (on-site group), while the Policlinico of Bari had nurses available on call 24/7 from the Neonatology Unit (on-call group). Results: Between January 3rd and March 31st, 2018, a total of 564 sets of mothers and babies were admitted - 299 on-site and 265 on-call. The exclusive breastfeeding rate for the entire group was 76.4% at 90 days, demonstrating the positive impact of rooming-in and nursing, regardless of the setting. Infants delivered via ce-sarean section in the on-site group demonstrated higher rates of exclusive breastfeeding at both 30 and 90 days of life. Conclusions: Our research indicates that having a nurse available at all times is crucial for promptly identifying any problems with breastfeeding. We highly suggest having an on-site nurse present during rooming-in for mothers who have had a caesarean delivery. This nurse should continuously promote exclusive breastfeeding until the baby is three months old.

This study compares the action of different handpieces (turbine, high-speed electric handpiece and piezoelectric device) on surface roughness of enamel and dentin when using diamond-coated working tips and burs of the same grit size. Experiment was conducted on 15 extracted first molars from patients aged 45 to 60 years. The occlusal portion was removed using a diamond-coated water wheel and then refined with a 120-130 μm grit bur in order to obtain a flat surface with an adequate exposition of the dentin core. Each surface was divided into three portions and every portion was finished with one of the three tested instruments. Rotary burs and piezoelectric tips had the same grit size (60 μm) and load on handpiece during preparation never exceeded 150 g. Surface roughness parameters (Ra, Rsk, Rku) were recorded with an optical profilometer and SEM analysis of treated surfaces and working tips was conducted. Ra and Rsk differed significantly between enamel and dentin only after using turbine (p=0.004 and p=0.007, respectively). No significant differences were observed in Ra, Rsk, and Rku between enamel and dentin when using high-speed electric handpiece or piezoelectric device. Turbine produced higher Ra and Rsk values on dentin than the other devices, while no significant differences were found between piezoelectric handpiece and high-speed electric contra-angle on both substrates. Summarizing, the findings of the present study demonstrated that turbine generated rougher surfaces on dentin compared to the other handpieces. Moreover, the turbine produced more asymmetrical surface profiles on both enamel and dentin. However, it should be considered that these differences in roughness (Ra) were within the range of 0.25-0.30 μm: it is still unclear if these variations, although statistically significant, will influence final clinical outcomes.

The images captured by UAVs during inspection often contain numerous small targets related to transmission lines, which are critical and vulnerable elements for ensuring the safe operation of these lines. However, due to various factors such as the small size of the targets, low resolution, complex background, and potential line aggregation, achieving accurate and real-time detection becomes challenging. To address these issues, this paper proposes a detection algorithm called P2-ECA-EIOU-YOLOv5 (P2E-YOLOv5). Firstly, in order to address the challenges posed by the complex background and environmental interference that impact small targets, an ECA attention module is integrated into the network. This module effectively enhances the network's focus on small targets while concurrently mitigating the influence of environmental interference. Secondly, considering the characteristics of small target size and low resolution, a new high-resolution detection head is introduced, which is more sensitive to small targets. Lastly, the network utilizes the EIOU-Loss as the regression Loss function to improve the positioning accuracy of small targets, as they tend to aggregate. Experimental results demonstrate that the proposed P2E-YOLOv5 detection algorithm achieves an accuracy P of 96.0% and an average accuracy (mAP) of 97.0% for small target detection in transmission lines.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

We report a small footprint cost-effective isothermal rapid DNA amplification system, with integrated microfluidics for automated sample analysis and detection of SARS-CoV-2 in human and environmental samples. Our system measures low-level fluorescent signal in real-time during amplification, while maintaining the desired assay temperature, on a low power, portable system footprint. A unique soft microfluidic chip design was implemented to mitigate thermocapillary effects and facilitate optical alignment for automated image capture and signal analysis. The system-on-board prototype coupled with the LAMP primers designed by BioCoS, is sensitive enough to detect viral loads of SARS-CoV-2 in a broad concentration range corresponding to a threshold cycle range of 16 to 39. Clinical specimens were tested at Kingston Health Sciences using a clinically validated PCR assay and variants were determined using whole genome sequencing.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

Influenced by the quasi-stationary Mei-yu front and the development of mesoscale low vortices on the Mei-yu front, a torrential rain event occurred in Suzhou on July 6, 2020. The 24-hour rainfall recorded by the automatic station exceeded 200 millimeters, with the highest hourly intensity surpassing 70 millimeters, accompanied by thunderstorms and strong winds. This heavy precipitation process was characterized by suddenness, extremity, long duration, high precipitation efficiency, and backward propagation. Using various data sources such as the European ERA5 reanalysis data, ground-based automatic stations, sounding, Doppler weather radar, and wind profile radar, this paper analyzed in detail the circulation characteristics and radar echo structures of this torrential rain event, and further studied the triggering, feature evolution, and maintenance mechanisms of the heavy precipitation.The results show: (1) The continuously strengthening low-level jet stream propagates downward forming an ultra-low-level jet stream. Heavy precipitation is located on the left front side of the jet exit area, where strong convergence and lifting in the boundary layer overlap with the ascending branch of the secondary circulation above the shear line, resulting in heavy precipitation. (2) A supercell storm with intense precipitation produced this heavy rainfall event, characterized by a low centroid of strong echo; echo-free vault, bounded weak echo region, and other supercell structural features. During this event, the high reflectivity factor areas corresponded to high KDP value areas, indicating a large amount of liquid water content. Vertically, the KDP column can track the rainwater mixing ratio well, and its location corresponds to the vicinity of the short-term heavy precipitation occurrence. The high KDP value area mainly consists of numerous precipitation particles, and the vertical vortex wind field structure causes rapid growth of precipitation particles through continuous rolling. Furthermore, it can be found through correlation coefficients (CC) that there are always high-value areas for CC since they correspond to areas of intense precipitation. (3) Continuous triggering of mesoscale convective cloud clusters on the east-west ground convergence line leads to new development and forms a "train effect." Strong frontogenesis in both horizontal and vertical directions triggers and sustains this heavy precipitation event. The significant increase in liquid water and water vapor density has indicative significance for the occurrence of heavy precipitation.

A closed form solution for the common and differential modal currents induced on a pair of infinitely long parallel conductors by a voltage source was derived. For lossy conductors the current consists of a continuous spectrum of radiation modes and (for the common mode) a modified low loss Sommerfeld-Goubau mode and (for the differential mode) a quasi-TEM mode. This model is used to investigate the influence of a parallel conductor on microwave power line communication systems. For typical parameters, it is shown that the performance of these systems can be enhanced.

Background: Cancer patients require cross-professional care during the diagnosis and treatment periods. Therefore, methods for effectively carrying out case management are essential to tumor care. Purpose: To investigate the effects of using the community software LINE Official Ac-count on oral cancer case management. Methods: An experimental design was used; 100 patients were randomly divided into two groups by using a computer-generated random number table. The experimental group used LINE Official Account, which gave them self-care information, timely messages, and one-on-one health-care consultations. The control group followed standard healthcare practices. Results: The experimental group was satisfied with the self-care information provided by LINE Official Account (86.9%), patients regularly checked the self-care information (89.4%) and would check the information when receiving a push notification (54.3%). Ten patients used the one-on-one consultation(20.0%). LINE Official Account had a significant effect on the rate of participation in support groups. Generalized estimating equations indicated a significant difference between the two groups regarding the overall quality of life over 7 days (P = 0.023). Conclusion: Community software applications used in oncological case management can improve self-management and empower, also enable tracking of long-term follow-up effectiveness and reinforce the case manager’s role as a family therapist. Therefore, this study recommends that case manager systems be incorporated into mobile applications to increase the sustainable management, accessibility, effectiveness, and satisfaction of oncological management systems. This study also provides the value of Sustainable Development Goals (SDGs) with Good Health and Well-being, and decreased social withdrawal among patients with oral cancer.

A unified critical state model has been developed for both clean sand and silty sand using the modified Cam-clay model (MCC). The main feature of the proposed model is a new critical state line equation in the e-ln(p) plane that is capable of handling both straight and curved test results. With this feature, the error in calculating plastic volumetric strain is eliminated in theory. Another crucial feature of the model is the transformed stress tensor based on the SMP (spatially mobilized plane) criterion, which takes into account the proper shear yield and failure of soil under three-dimensional stresses. Additionally, the proposed model applies the intergranular void ratio with the fines influence factor for silty sand. Only eight soil parameters are required for clean sand, and a total number of twelve soil parameters are needed for silty sand.

Companion animals play a central role in many families and are especially valued by those who are socially isolated. Crisis situations such as acute hospitalizations, homelessness and natural disasters can make it difficult to preserve the human-animal bond and can result in animals being surrendered or euthanized. Social support programs like the RSPCA NSW Emergency Boarding and Homelessness program support people experiencing crisis situations with emergency pet boarding, access veterinary treatment and individualized case management. This study aimed to estimate the social return on investment (SROI) for this program using standard SROI methodology. In-depth interviews were conducted with 13 program stakeholders and questionnaire responses were received from 29 program clients. Outcomes were quantified for four stakeholder groups: program clients, client’s animals, RSPCA Inspectors, animal pounds and shelters. Clients and their animals experienced the bulk of the benefit from the program, estimated to have a combined value of over $5 million AUD for the 2020-21 financial year. The estimated social return on investment was $8.21 for each $1 invested. The study demonstrates that keeping people together with their companion animals, or ensuring they are reunited as soon as possible, can reduce stressors, and improve outcomes for people and animals.

Autonomous vehicles (AVs) may not only reduce parking demand, but also free up on-street parking spaces. From the perspective of bus priority, converting on-street parking lots into dedicated bus lanes can both ensure bus priority and accommodate non-bus traffic, helping to reduce congestion and pollution. In order to study the impact of conversion of on-street parking lots to bus lanes on traffic flow, a microscopic simulation framework based on VISSIM is proposed in this paper. Data was collected using the floating car method and video recording method to quantify the factors affecting traffic flow due to the conversion of on-street parking. The VISSIM simulation model was then calibrated. According to the proportion of the on-street parking lots into a bus lane, the on-street parking lots conversion simulation model of different scenarios was established, and the influence of different on-street parking lots conversion ratio on traffic efficiency and pollution emission was quantitatively analyzed. Finally, the optimization method based on bus lane network connectivity is discussed. The results indicate that: When the on-street parking lots conversion ratio is approximately 100%, bus speed increases by 21.03%, bus delays decrease by 14.27%, and bus parking instances decrease by 11.31%. Total emissions are negatively correlated with vehicle speed. As the conversion rate of on-street parking increases, the emissions of road segments and the entire road network gradually decrease. At a conversion ratio of 100%, the average total emissions for road segments have the highest reduction rate, decreasing by 4.12%. At a conversion ratio of 50%, the average emission total for the road network shows the largest reduction, falling by 2.88%.

This paper presents a new algorithm for semi-supervised action recognition using adaptive feature analysis. We model the samples of the same action as the same manifold and those of different actions as different manifolds, and integrate feature correlation mining and visual similarity mining into a joint framework. By maximizing the separability between different classes based on the labeled data, the proposed algorithm learns multiple features from labeled data and utilizes the intrinsic geometric structure of the data distribution between labeled and unlabeled data to boost the recognition. We introduce Projected Barzilai-Borwein (PBB) to train a subspace projection matrix as classifier. Extensive experiments on three benchmark datasets demonstrate that our algorithm outperforms the existing semi-supervised action recognition algorithms when there are a few labeled training samples.

High blood cholesterol levels are one of the main risks for atherosclerotic disease. A purified aqueous extract of Fucus vesiculosus, characterized as rich in phlorotannins and peptides, was described as having the capacity to inhibit cholesterol biosynthesis and intestinal absorption. In this work, the effect of this extract on intestinal cells metabolites and proteins was analysed, aiming to expand the knowledge about its mode of action targeting cholesterol metabolism, in particular exogenous cholesterol absorption and transport. Caco-2 cells differentiated into enterocytes were exposed to the purified aqueous extract of F. vesiculosus and analysed by undirected metabolomics and proteomics. The results of the metabolomic analysis showed only statistically significant differences in glutathione content of the cells exposed to the extract relatively to the control cells, with a decreased glutathione expression in exposed cells. The proteomic analysis showed an increased expression for cells exposed to the extract of NPC1, an important protein known to be involved in cholesterol transport. To extent of our knowledge this is the first study using untargeted metabolomics and proteomic analysis to study the effect of F. vesiculosus on differentiated Caco-2 cells, which aims to provide some insight about the molecular mechanism of extract compounds on intestinal cells.

The idea of an extension of life for CubeSats is proposed to reduce space debris in a low-earth orbit. In this work, a gripper is designed for geometry-based grasping in berthing tasks. The grasping operation is outlined for square- and rectangle-profiled CubeSats. Equilibrium conditions are used to choose fingertips shape and parameters for grasping the CubeSat body. A design scheme is proposed to provide the required accuracy. A design concept is developed into a lab prototype by using low-cost 3D printing technique, and a mock-up grasping task that is representative of the berthing operation is evaluated with the lab prototype. Center-mass hanging setup for the prototype and grasped body is used to evaluate the impact of grasping, partially replicating the conditions in space by reducing the effect of gravity on the system.

MultiCal is an affordable, high-precision measuring device designed for the on-site calibration of industrial robots. Its design features a long measuring rod with a spherical tip that is attached to the robot. By restricting the rod’s tip to multiple fixed points under different rod orientations, the relative positions of these points are accurately measured beforehand. A common issue with MultiCal is the gravity deformation of the long measuring rod, which introduces measurement errors into the system. This problem becomes especially serious when calibrating large robots, as the length of the measuring rod needs to be increased to enable the robot to move in a sufficient space. To address this issue, we propose two improvements in this paper. Firstly, we suggest the use of a new design of the measuring rod that is lightweight yet has high rigidity. Secondly, we propose a deformation compensation algorithm. Experimental results have shown that the new measuring rod improves calibration accuracy by 20% to 39%, while by using the deformation compensation algorithm, the accuracy increases by 6% to 16%. In the best configuration, the calibration accuracy is similar to that of a measuring arm with a laser scanner, producing an average positioning error of 0.274 mm and a maximum positioning error of 0.838 mm. The improved design is cost-affordable, robust, and has sufficient accuracy, making MultiCal a more reliable tool for industrial robot calibration.

Interference on Power Line Communication (PLC), which is a wired communication technology that provides communication and data transmission over the existing electrical network, is examined in this paper. Many applications employ PLC technologies, which have the benefit of leveraging existing power connections for both power and data transfer, reducing cost and complexity. These interactions may be observed in contemporary smart grids and automobile power networks, where lengthy cables, switching power supplies, and communication links all work together but exacerbate electromagnetic interference problems. This research examines the effects of Spread Spectrum methods used to reduce EMI from power converters on PLC systems. Spread spectrum modulation and its three variants Sine, Random and Triangle are frequently employed to meet the requirements of electromagnetic compatibility, however there are some repercussions, that might be detrimental to the converter or the rest of the electrical network. These outcomes occur for various modulation algorithm settings and at various frequencies. Measurements are made utilising the Frame Error Rate value provided by the PLC link system to ascertain the interference produced by a SiC-based DC-DC converter in order to investigate these concerns and standardise an assessment approach.

Despite the recent advances in melanoma therapy, the need for new targets and novel approaches to therapy is urgent. We previously reported melanoma actives that work via binding and downregulating spliceosomal proteins hnRNPH1 and H2. In a separate study, we reported that these compounds were non-toxic to Balb/C mice at 50 mg/kg suggesting their utility in in vivo studies. In the present study, we aimed to determine the therapeutic potential of these compounds by testing them in A375 cell-line derived xenograft in nu/nu mice. Animals were randomized into four groups (n=12/group) to receive subcutaneous administration of vehicle, 10 mg/kg vemurafenib, and 25 mg/kg 2155-14 and 2155-18 three times per week for 15 days along with a control group. The results revealed that both 2155-14 and 2155-18 significantly decreased the growth of A375 tumors, which was comparable to vemurafenib. These results were confirmed by tumor volume, weight, and histopathological examination. In conclusion, these results suggest a therapeutic potential of targeting spliceosomal proteins hnRNPH1 and H2.

Loss of photoreceptors in retinal degenerative diseases also impacts the inner retina: bipolar cell dendrites retract, neurons rewire and protein expression changes. ON-bipolar cells represent an attractive target for optogenetic vision restoration. However, above-described maladaptations may negatively impact the quality of restored vision. To investigate this question, we employed human post-mortem retinas and transgenic rd1_Opto-mGluR6 mice expressing the optogenetic construct Opto-mGluR6 in ON-bipolar cells and carrying the retinal degeneration rd1 mutation. We found significant changes in delayed rectifier potassium channel expression in ON-bipolar cells of degenerative retinas. In particular, we found an increase in Kv1.3 expression already in early stages of degeneration. Immunohistochemistry localized Kv1.3 channels specifically to OBC axons. In whole-cell patch-clamp experiments, ON-bipolar cells in the degenerated murine retina were less responsive, which could be reversed by application of the specific Kv1.3 antagonist Psora-4. Notably, Kv1.3 block significantly increased the amplitude and kinetics of Opto-mGluR6-mediated light responses in ON-bipolar cells of the blind retina and increased the signal-to-noise ratio of light-triggered responses in retinal ganglion cells. We propose that reduction of Kv1.3 activity in the degenerated retina, either by pharmacological block or by KCNA3 gene silencing, could improve the quality of restored vision.

In this paper, new N-way Wilkinson power dividers (WPDs) are represented by using slow-wave structures such as narrow slits loaded and meandered transmission lines. The slit loaded and meandered lines are used to represent the quarter wavelength transmission lines of a conventional WPD for size reduction. Based on the proposed approaches, 2-, 4- and 8-way power dividers are designed, simulated and fabricated. The fabricated -, 4- and 8-way circuits have been measured at the center frequencies of 2.03, 1.77, and 1.73 GHz in an excellent agreement with the predicted ones. The meandered transmission lines are also used to design new types of WPDs having novel input/output port arrangements. For this purpose, two 3-way WPDs are located at both sides of the same board so as to have different power splitting ratios at different inputs and outputs to provide alternative solutions for antenna arrays. Furthermore, a 5-way dual layer WPD is introduced by locating the meandered transmission lines to two layers. The proposed 3- and 5-way WPDs allow halving the input power at the next output port in the order of P/2, P/4, P/8, P/16, and P/16. All of the designed power halving WPDs have been simulated, fabricated and successfully tested.

Material identification based on R_value (transparency natural logarithm ratio of low-energy to high-energy) of line-scan dual-energy X-ray transmission (DE-XRT) has a good prospect for industrial application. Unfortunately, the DE-XRT signals before attenuation cannot be directly measured, whereas their precision is very important to R_value. Therefore, a context-based signal synthesis method which takes the filtered signals that remove high-frequency noises and retain low-frequency actual fluctuations as the reference value, and takes into account the vertical (forward/column) direction and horizontal (scanning/row) direction anisotropy of line-scan images was proposed. The vertical is a time series with continuity of signal trend; the horizontal is a spatial characteristic with the fluctuation synchronization within the same row signals. The special synthesis evaluations of curve synthesis difference and surface synthesis difference were also proposed. Experimental results show that the tow evaluations are both only about 0.0007, and it only takes 35 ms to complete the surface synthesis of 119×119 pixels on the CPU with 3.4 GHz main frequency. The presented method can achieve high signal synthesis precision and calculation real-time, so as to facilitate DE-XRT material identification. It can be extended to improve the precision of numerical synthesis in other line-scan uncomplete signals.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

The gut plays a key role in drug absorption and metabolism of orally ingested drugs. Additionally, characterization of intestinal disease processes are increasingly gaining more attention as gut health is an important contributor to our overall health. The most recent innovation to study intestinal processes in vitro is the development of gut-on-a-chip (GOC) systems. Compared to conventional in vitro models they offer more translational value, and many different GOC models have been presented over the past years. Here, we reflect on the almost unlimited choices in designing and selecting a GOC for preclinical drug (or food) development research. Four components that largely influence the GOC design are highlighted, namely 1) the biological research questions, 2) chip fabrication and materials, 3) tissue engineering, and 4) the environmental and biochemical cues to add or measure in the GOC. Examples are presented of GOC studies in the two major areas of preclinical intestinal research: 1) intestinal absorption and metabolism to study the oral bioavailability of compounds, and 2) treatment-orientated research for intestinal diseases. The last section of this review presents an outlook on the limitations to overcome in order to accelerate preclinical GOC research.

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.

A large body of evidence indicates that environmental agents can induce alterations in DNA methylation (DNAm) profiles. Radiofrequency electromagnetic fields (RF-EMFs) are radiations emitted by everyday devices which have been classified as “possibly carcinogenic”, however their biological effects are unclear. As aberrant DNAm of genomic repetitive elements (RE) may promote genomic instability, here we sought to determine whether exposure to RF-EMFs could affect DNAm of different classes of RE, such as long interspersed nuclear element1s (LINE-1), Alu short interspersed nuclear element and ribosomal repeats. To this purpose, we analysed DNAm profiles of cervical cancer and neuroblastoma cell lines (HeLa, BE(2)C and SH-SY5Y) exposed to 900 MHz GSM-modulated RF-EMF through an Illumina-based targeted deep bisulfite sequencing approach. Our findings showed that radiofrequency exposure did not affect DNAm of Alu elements in any of the cell lines analysed. Conversely, it influenced DNAm of LINE1 and ribosomal repeats in terms of both average profiles and organization of methylated and un-methylated CpG sites, in different ways in each of the three cell lines studied.

The Influenza A Virus (IAV) represents an enveloped, positive-sense and single-stranded RNA-based virus that infects mammals mainly via the respiratory system, although other bodily systems are also infected and undergo various extents of inflammatory pathogenesis. There are two well-known strains of IAV that cause life-threatening disease in mammals; H1N1 and H5N1, and the first strain caused the 1918 IAV H1N1 pandemic that claimed between 30 and 50 million human lives. Due to the significant ability of IAV to evade important immune recognition, the virus was observed to favor the onset of secondary microbial infections (i.e. bacterial or fungal), as the overall performance of the immune system became transiently weakened during the viral infection. During the IAV H1N1 pandemic, many patients died as a result of bacterial pneumonia, as pathogenic bacteria, such as Streptococcus pneumoniae and Haemophilus influenzae, gained a wider opportunity to colonize and infect vital areas of the lower respiratory tract, and such a phenomenon led to the excessive, prophylactic usage of antibiotics due to the increased levels of panic, which in turn favored the natural selection of bacteria with genes that became resistant to such antibiotics. Antibiotics might be required for usage solely when bacteria are known to be colonizing vital areas of the human body, and this aspect is tricky, as colonization is asymptomatic and screening is consequently rare. Recently, new variants of the avian IAV H5N1 strain were transmitted from live, infected birds to mammals, including humans in some isolated cases, and given that there have already been several zoonotic spillover events overall since the beginning of 2023, we are rapidly approaching the time when a zoonotic spillover into humans will mark the first epidemic outbreak of the avian flu in humans. A lethality rate of 60% was projected by the World Health Organization, as the virus was shown to favor the development of life-threatening hyper-inflammatory responses at the levels of alveolar tissues constituted by Type II pneumocytes. There are hints that novel variants of H5N1 are capable of infecting the intestinal layer, as recently, two dolphins died as a result of ingesting infected birds within the area of the British Isles. IAV is known to suppress the production and transmission of Type I Interferons by expressing various non-structural proteins (NSPs), such as NSP1, which was found to be also packaged into exosomes and transmitted to neighboring uninfected cells, thereby preventing them from responding to the virus in the first place. A more pronounced rate of innate immune evasion would probably be observed in H5N1 IAV infection than in the infection caused by recent variants of H1N1 IAV. The H5N1 strain of IAV was also found to secrete a higher concentration of NSP1 than SARS-CoV-2, indicating the existence of an association to the greater mortality rate of H5N1 IAV infection. A direct, prophylactic stimulation of the interferon system using a reduced oral or nasal dosage of recombinant anti-inflammatory and anti-viral interferon glycoproteins may represent the most viable approach to prevent an emergence of a life-threatening H5N1 IAV pandemic. A similar non-invasive approach could be developed for an Marburg Virus (MARV) and a Nipah Virus (NiV) infection of humans, as risks of the emergence of a Marburg epidemic and also of a Nipah epidemic may be substantial at this stage as well. Clinical testing of clinical approaches as such could be of critical importance at the moment. Animals could also benefit from related clinical approaches. Somatic natural and adaptive lymphocytes treated with IFN I and III could also constitute a substantial approach of immunization and heavily favor an indefinite shift in the evolutionary battle between the host organism and microbes of public health concern.

The paper presents the measured values of tensile forces acting on transmission idlers in the upper and lower run of a conveyor belt placed on a laboratory machine designed at the Department of Machine and Industrial Design, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava). The tensile forces detected by two strain gauge load cells and recorded using DEWESoft software were used to calculate the friction coefficient which acts on the surface of the driving drum casing and the conveyor belt. The friction coefficient at the slip point, or during the slippage of the conveyor belt on the rubber or steel casing of the driving drum was determined for two states of the surfaces which are in contact. Experimental measurements on a laboratory machine determined four values of friction coefficients, for two types of drum surfaces and for two states of contact surfaces, which were compared with the recommended standard values. The measured values reached higher values in comparison with the values given by the CSN standards. The highest deviation of 273.3% is achieved using a steel wet surface, and the lowest deviation of 106.3% is achieved when using a rubber dry lining for the driving drum casing. On the presented laboratory machine, it is possible to measure tensile forces for different speeds of movement, different belt angles on the driving drum, various types of belt surfaces, different types of drum casing linings and different sizes of tension forces for the endless loop of the conveyor belt. For these characteristics of the conveyor belt, the magnitude of the friction coefficient, acting between the belt and the drum surfaces, can be determined.

The influence of neutrosophy in the previous period is constantly growing in many areas of science and technology. Moreover, various applications of the neutrosophic approach have become more common in recent years. Our goal in this research is to utilize the neutrosophy to improve the performance of the Dai-Liao conjugate gradient (CG) method. Specifically, in this research, we propose and investigate a new neutrosophic logic system to calculate the key parameter t involved in the Dai–Liao CG iterations. Theoretical analysis and numerical experience indicate that the efficiency and robustness of the new rule for determining t. Combining the neutrosophy and the Dai-Liao conjugate gradient method, we propose and explore a new Dai-Liao CG iterations for solving large-scale unconstrained optimization models. The global convergence is established under common assumptions and the backtracking line search. Finally, by conducting numerical experiments, computational evidence demonstrates that the new fuzzy neutrosophic Dai-Liao conjugate gradient method is computationally effective and robust.

A variational analysis of dispersion medium (electrolytes and surfactants) was carried out for the best nucleotide interactions with the presence of nanoparticles and the ability to formation of homogeneous coatings upon drying / lyophilization. Using UV-spectroscopy and transmission electron microscopy, the processes of immobilization of nucleotides on the surface of nanoparti-cles of the composition ZrO2-3mol% Y2O3 (YSZ) in the presence of various dispersing agents were investigated. Promising dispersing agents were established, the optimal composition of suspen-sions based on DNA nucleotides and YSZ nanoparticles, which is potentially suitable for adaptive technologies of bionanoelectronics, was selected. The aim of the work is to obtain and study functional media for molecular electronics based on heterojunctions biological molecule – wide-gap dielectric.

The study sought to determine the rate of discordant results between genotypic and phe-notypic tests for the diagnosis of drug resistant tuberculosis (DR-TB). Sputum samples and cultured isolates from suspected DR-TB patients were respectively analysed for My-cobacterium tuberculosis by Xpert® MTB/RIF (Cepheid, USA) and Line Probe Assays (LPA) (Hain, Germany). Discrepant Rifampicin (RMP) resistant results were confirmed using BACTEC MGIT960 (BD, USA). Of 224 RMP-resistant by Xpert MTB/RIF, 5.4% were suscep-tible to RMP by LPA. MGIT960 showed 75% agreement with LPA. Discrepancy was at-tributed to either heteroresistance or DNA contamination during LPA testing in 58.3% of cases. In 25% of samples showing agreement in RMP resistance between Xpert MTB/RIF and MGIT960, discrepancy was attributed to laboratory errors causing false RMP suscep-tible results with LPA. Of 16.7% of cases, discrepancy was attributed to false RMP suscep-tible results with Xpert MTB/RIF. Of 224 isolates, susceptibility to isoniazid (INH) by LPA was performed in 73.7% RMP resistant isolates, of which, 80.6% were resistant. All RMP resistant isolates by Xpert MTB/RIF were confirmed in 98.5% by LPA if TB isolates were resistant to INH, but only confirmed in 81.3% if TB isolates were INH susceptible (ρ < 0.001). In conclusion, Laboratory errors should be considered when investigating dis-cordant results.

Nowadays, in low voltage (LV) electric distribution networks (EDNs), the Distribution Network Operators (DNOs) are encountering a high number of connected small-scale distributed generation units, mainly photovoltaic (PV) prosumers. The irregular behavior of the prosumers, together with the uncertainty degree of the requested and injected powers associated with all end-users from the LV EDN, can cause voltage variations with violations of the allowable limits. In this context, the paper developed an efficient and resilient expert system integrating the rule-based reasoning applied to the On-load Tap Changer (OLTC)-fitted transformer to improve the efficiency of the voltage control in the PV-rich LV EDNs. An in-depth analysis based on 75 scenarios, resulting from the combinations of three indicators: the penetration degree of the PV prosumers, consumption evolution associated with the consumers, and energy production of the PV systems, has been performed to demonstrate the efficiency of the proposed expert system in an LV EDN from a rural area belonging to a Romanian DNO. The success rate of the expert system has been 86.7% (65 out of 75 scenarios didn't have voltage issues, all values being between the allowable limits in 100% of the time slots associated with the analyzed period). For the other scenarios (representing 13.3%), the values have been inside the range [-10%, +10%] at least 95% of the time slots, according to the European Power Quality Standard, and for the rest of the time slots up to 100% being very close to the upper and lower limits of the range, with highly mitigating of the voltage variations.

Document deskewing is a fundamental problem in document image processing. While existing methods have limitations, such as Hough Line Transformation that can deskew images upside down, and Deep Learning models that require huge amounts of human labour and computational resources and still fail to deskew while taking care of orientation, OCR-based methods also struggle to read text when it is tilted. In this paper, we propose a novel, simple, cost-effective deep learning method for fixing the skew and orientation of documents. Our approach reduces the search space for the machine learning model to predict whether an image is upside down or not, avoiding the huge search space of predicting an angle between 0 and 360. We finetuned a MobileNetV2 model, which was pre-trained on imagenet, using only 200 images and achieve good results. This method is useful for automation-based tasks, such as data extraction using OCR technology, and can greatly reduce manual labour.

Background: Artificial intelligence can help improve the quality of healthcare by analyzing vast amounts of data and providing more effective and personalized treatment plans. Researchers are working on developing AI-powered solutions that can help improve the outcomes of patients. Objective: To explore the potential of AI in improving healthcare outcomes and patient experience. Results: The study suggests that AI can improve healthcare efficiency and patient outcomes but cannot fully replace human healthcare professionals. AI can assist healthcare professionals in their work, leading to better resource utilization and improved patient care. However, there is still a need for human healthcare professionals to oversee AI systems and provide empathy and personalized care to patients. Conclusion: While there is immense potential for AI in healthcare, it is not yet feasible to replace human healthcare workers. Instead, it should be viewed as a tool that can help improve the efficiency and effectiveness of human healthcare.

Digital microfluidics (DMF) holds great potential for the alleviation of laboratory procedures in assisted reproductive technologies (ARTs). Electrowetting on dielectric (EWOD) provides dynamic culture conditions in vitro that may better mimic the natural embryo microenvironment. Thus far, EWOD microdevices have been proposed for in vitro gamete and embryo handling in mice and for analyzing the human embryo secretome. This article presents the development of the first microfluidic chip utilizing EWOD technology designed for the manipulation of bovine embryos in vitro. The prototype sustains the cell cycles of embryos manipulated individually on the chips during in vitro culture (IVC). Challenges related to the chip fabrication as well as to its application during bovine embryo IVC in accordance with the adapted on-chip protocol are thoroughly discussed, and future directions for DMF in ARTs are indicated.

Industrial data scarcity is one of the largest factors holding back the widespread use of machine learning in manufacturing. To overcome this problem, the concept of transfer learning was developed and it achieved high attention in recent industrial research. Our paper focuses on the problem of time series segmentation and presents the first in-depth research about transfer learning for deep-learning based time series segmentation on the example of industrial end-of-line pump testing. In particularly, we investigate if the performance of deep learning models can be increased by pretraining the network with data from other domains. Three different scenarios are analyzed: source and target data being closely related, source and target data being distantly related, and source and target data being non-related. The results demonstrate that transfer learning can enhance the performance of time series segmentation models in respect to accuracy and training speed. The benefit is most clearly seen in scenarios where source and training data are closely related and the number of target training data samples is lowest. However, in the scenario of non-related datasets, cases of negative Transfer Learning were observed as well. Thus, the research emphasizes the potential, but also the challenges of industrial Transfer Learning.

The SARS–CoV-2 infection has caused both acute and chronic COVID–19 disease during the recent pandemic with emerging more transmissible SARS–CoV–2 Omicron variants (BQ1 and XBB1) that have increased demands for more effective immunogens and therapeutic approaches to protect the lives of numerous SARS–CoV-2 affected individuals and reduce overall disease burden that could be affected by concurrent other pathogens causing diseases. Following a worldwide campaign of mass vaccination, there is still a significant demand to quell the harmful effects of novel SARS–CoV–2 infections due to higher mutation rates within specific areas of the SARS–CoV-2 domain, leading to enhanced viral entry, especially within individuals with one or more significant comorbidities, and there is still a dilemma of how prevention of future pandemics will occur as within host animal mutations and cross species transfer naturally occurs. Concerns intersect at a specific point; a gained evolutionary ability of several viruses over the previous centuries to remain undetected during the first stages of infection by means of capping the 5' end of their DNA and RNA genes respectively. This may occur by reducing the rate of host Type I and Type III Interferons (IFN) cellular synthesis, that would usually occur and affect both apoptotic pathways, that facilitate viral replication and clearance, as well as immune cells, that process and present pathogenic antigen epitopes. Furthermore, although methods of vaccination exist, other methods in clinical development remain that could evoke an immune response in different cellular, serum or mucosal compartments being cellular, serum and mucosal that evoke differential antibody responses. Antibodies are classed as natural and synthetic. Natural antibodies are further classified into neutralizing and non-neutralizing, whilst synthetic antibodies are also further classified into monoclonal and polyclonal. As a result of single cell study transcriptome research, viruses do utilize an array of protein receptors for receptor-mediated cellular entry. This, therefore suggests that potential differential production of antibody immunoglobulins (Ig) within serum and mucosal areas remains affected by cytokines, adhesion molecules and chemokines that can be upregulated or downregulated upon host viral infection. Serum plasma antibodies can be multimeric that may not efficiently cross the nasal epithelium cell layer, therefore offering less protection against mucosal inflammation due to mucin proteins. On the other hand, antibodies produced by mucosal plasma cells at epithelial surfaces are known to provide effective immune responses in some viral infections. The existence of developments that stimulate mucosal immune responses has so far only been seen with influenza nasal immunogens. Nevertheless, scientists developed ways of immunization and early treatment worldwide that generally showed good success rates and fewer risks of adverse events, and the still early present stages of COVID-19 research should also be taken into consideration. For example, the administration of human interferons I and III into the nasal mucosa cellular layer, as key mediators of anti–viral activity, can stimulate cellular activity to train the innate and adaptive immune system cells to develop and appropriately stimulate an adequate immune response through B and T cells. Recently, it was discovered that specific plants secrete proteins that also stimulate the production of Type I Interferons. It might be that focusing on directly offering the immune system the information about the genetics and protein structure of the pathogen, rather than training its first-line mechanisms to develop faster, excessively increases its specificity, making it reach a level that brings the virus the opportunity to evolve and escape previously-developed host immune mechanisms. Naturally-selected polymorphic viruses through genetic recombination pose challenges to traditional concepts of cellular and molecular immune system neutralization of these viruses during the first stages of cellular infection. It is until the scientific community realizes this potentially crucial aspect that we will probably continue to face serious epidemics and pandemics of respiratory diseases over the coming several decades, evidenced with dengue fever and more recently monkeypox. Type I IFNs tend to be produced faster than Type III IFNs, and the first induce slightly more abundant pro-inflammatory signals than the latter, meaning that type III IFNs, if produced early, may further decrease the extent of excessive proinflammatory signals. Hence, we believe that nasal sprays containing a low dosage of Type I and Type III IFNs not only represent a relevant COVID-19 therapeutic, but also a potential unknown modulatory therapy of the future. Of note, it has been indicated that IFN I and / or III display significant immunizing and early therapeutic effects for other viral evoked diseases like Influenza (Influenza (A)H1N1), rabies (Rabies lyssavirus), measles (Measles virus), rubella (Rubivirus rubellae), Hepatitis B, HIV-induced AIDS, Ebola, Marburg, as well as bacterial diseases, such as lower respiratory tract infectious diseases induced by Haemophilus influenzae, Streptococcus pneumoniae and Staphylococcus aureus, and a number of oncological diseases, like hepatic melanoma.

Conventional diagnostic techniques are based on utilization of analyte sampling, sensing and signalling on separate platforms for detection purposes, that must be evaded and integrated to a single step procedure in point of care (POC) testing devices. Therefore, the trend has been shifted towards utilization of microfluidic platforms for detection of analytes in biochemical, clinical and food technology due to its being expeditious. Microfluidic systems moulded with polymer substances or glass offer specific and sensitive detection of infectious and non-infectious diseases by providing innumerable benefits including less cost, good biological affinity, strong capillary action and simple process of fabrication. In the case of nucleic acid-based nanosensors, there are some challenges that need to be addressed such as cellular lysis, isolation and amplification of nucleic acid required to be accomplished prior to its detection. To avoid utilization of laborious steps for executing these steps, advances have been deployed in this perspective for on-chip sample preparation, amplification and detection which not only improves sensitivity and selectivity but also saves time and resources. This review emphasizes the significance of microfluidic technology for nucleic acid detection of infectious and non-infectious diseases. The implementation of isothermal amplification in concomitance with lateral flow assay greatly increases the binding efficiency of nanoparticles and biomolecules, improves limit of detection and sensitivity. Most importantly deployment of paper-based material made of cellulose reduces the overall cost. Microfluidic technology in nucleic acid testing has been discussed by explicating its applications in different fields. This review concludes with the prospects and proposes future directions in microfluidic based methods in disease diagnosis.

The lab-on-a-chip concept, enabled by microfluidic technology, promises the integration of multi-ple discrete laboratory techniques into a miniaturised system. Research into microfluidics has generally focused on the development of individual elements of the total system (often with rela-tively limited functionality), without full consideration for integration into a complete fully opti-mised and miniaturised system. Typically, the operation of many of the reported lab-on-a-chip devices is dependent on the support of a laboratory framework. In this paper, a demonstrator platform for routine laboratory analysis is designed and built, which fully integrates a number of technologies into a single device with multiple domains such as fluidics, electronics, pneumatics, hydraulics, and photonics. This facilitates the delivery of breakthroughs in research, by incorpo-rating all physical requirements into a single device. To highlight this proposed approach, this demonstrator microsystem acts as a fully integrated biochemical assay reaction system. The re-sulting design determines enzyme kinetics in an automated process and combines reservoirs, three-dimensional fluidic channels, optical sensing, and electronics in a low-cost, low-power and portable package.

Stark widths for 23 transitions in Al IV have been calculated employing modified semiempirical method. The results are obtained for an electron density of 10^17 cm−3 and temperatures from 10,000 K up to 160,000 K. The results obtained in this investigation are used for the examination of the influence of Stark broadening in Al IV stellar spectra, as well as to check Stark width regular behavior and similarites within Al IV spectrum.

As the era of omics continues to expand, omics-based experiments have become popular in industrial biotechnology. They promise deeper biological understanding, which may be leveraged to develop novel solutions to bioprocess optimization and cell line engineering strategies. Despite this expansion, naivety about what omic data offers and how to best handle such data can challenge the extraction of actionable value. However, the value of omic experiments in biotechnology research and development can be maximized with deliberate application of omic approaches and forethought about analysis techniques. Here we describe important considerations when designing and implementing omic-based experiments, and discuss how systems biology analysis strategies can enhance efforts to obtain actionable insights in biomanufacturing.

Ovarian cancers are curable by surgical resection when discovered early enough. Unfortunately, most ovarian cancers are diagnosed in the later stages. One strategy to identify early ovarian tumors is to screen women who have the highest risk scores. This mini review summarizes the accuracy of different methods used to assess the risk of developing ovarian cancer, including family history, BRCA genetic tests, and polygenic risk scores. The accuracy of these is compared to the maximum theoretical accuracy, revealing a substantial gap. We suggest that this gap, or missing heritability, could be caused by epistatic interactions between genes. An alternative approach to computing genetic risk scores, using chromosomal-scale length variation should incorporate epistatic interactions. Future research in this area should focus on this and other alternative methods of characterizing genomes.

Microbial immune escape represents the primary cause of induced pathogenesis in humans, and it represents a pivotal method used by viral agents to increase their load and suppress key mechanisms of the innate and adaptive immune system. This phenomenon represents the primary factor that led to the onset of the 1918-1920 A(H1N1) Influenza and 2020-2022 COVID-19 pandemics, and it possibly played a major role in the onset of the AIDS pandemic as well. Moreover, repeated incidents of immune evasion could be associated with higher rates of cellular aging (Jackson et al., 2017), most likely due to the consequent increased demands of energy consumption. Highly developed viral immune evasion ultimately indicates the high inner intelligence of human immunity due to reflective and imitative characteristics of reactions that are produced against initial actions. Ribonucleic acid-based viral genomes contain open reading frames, which consist of genes producing sixteen non-structural proteins. Such proteins play a considerable role in desensitizing first-line immunity during cellular infection, and non-structural proteins 1, 10 and 16 have the strongest effects against a healthy expression rate of Type I and Type III Interferon-encoding genes. Type I Interferons consist of IFN-alpha, -beta, -delta, -epsilon, -omega, -tau and -zeta, whilst Type III Interferons consist of IFN-lambda1, -lambda2 and -lambda3, and they act as stimulators of intracellular signalling cascades that in turn lead to the activation and expression of interferon-stimulated genes (Brown et al., 2022). The earlier the interferon-stimulated genes are activated, the lower the extent of pro-inflammatory mediation and overall, the more effective the antiviral immune response will be, given the exponential nature of the viral load increase. Non-structural protein 16 methylates the 5’ cap of the virus, making the pathogen-associated molecular patterns less recognisable by pattern-recognition receptors, and it requires activation by bonding with non-structural protein 10. It is preserved in the S-Adenosyl-L-Methionine pocket of the SARS-CoV-2 genome. Non-structural protein 1 (NS1) directly cleaves the host cell mRNA producing Type I and possibly Type III Interferons, thereby preventing a translation process of the immune proteins. NS1 has recently been found to often be packaged into exosomes once secreted by the viral genome in the cytosol, meaning that exocytosis and paracrine signalling to neighbouring cells before their actual infection is possible. As a result, NS1 is highly capable of silencing the first-line immune responses of uninfected neighbouring cells as well, thereby highlighting the need to adjust the focus of therapeutics and vaccinology toward first-line immunity and further indicating its foundational importance in the support for the development of precise and balanced defenses against microbial agents of concern (EL SAFADI et al., 2022).

This paper introduces a novel 3D NoC router that combines buffered and bufferless routing with approximate priority comparison when deflecting flits. Our proposal is a modification of an asymmetrical router that is buffered in the z dimension ports and bufferless in the x and y dimension ports. Flits that request output ports in the x and y dimensions are granted or deflected based on approximate, instead of accurate, priority comparison. Experimental results show that the proposed router, besides effectively combining the advantages of both buffered and bufferless routers, it achieves additional performance and area gains due to the reduced logic required for approximate priority comparison in flit deflections. Experimental results using synthetic and realistic traffic show that the proposed router begins to saturate at a sifnificantly higher injection rate than a bufferless router, but at a slightly lower injection rate than when using accurate priority comparison. Furthermore, the proposed router achieves higher clock frequencies and reduced area compared to the simpler permutation network.

The final assembly of appliances and automotive industries is a rigorous process, that has limited capabilities of full traceability associated with: (1) the parts installed, (2) their fabrication processes, and (3) the assembly work. This is also the case for each of its sub-assemblies The many parts and sub-assemblies that compose the final assembly, make full traceability a challenging fit, that is almost unsurmountable. Such full traceability along the entire supply-chain is not existent today and must be based on documentation of most assembled parts, assembly tasks, and inspection tasks that compose the full assembled product. In addition, security measures are needed to prevent hostile hacking and unauthorized approach to the assembly documentation throughout the entire supply chain. The related documentation and repeated verifications require considerable effort and have many chances for human errors. So, automating these processes has a great value. This article expounds a framework that harnesses block-chain and smart-contract technology to offer traceable and protected documentation of the assembly process. We expand the concept of a Bill-Of-Assembly (BOA) to incorporate data from the bill of materials (BOM), the associated assembly activities, the associated activities’ specification parameters and materials, and the associated assembly resources (machines and/or operators). The paper defines the operation of the BOA with blockchain and smart-contract technology, for attaining full traceability, safety, and security, for the entire assembled product. Future research could extend the proposed approach to facilitate the usage of the BOA data structure in constructing a digital twin of the entire simulated system.

This work communicates cavity ring-down spectroscopy (CRDS) of methylidyne (CH) in a chemiluminescent plasma that is produced in a microwave cavity. Of interest are the rotational lines of the 0-0 vibrational transition for the A-X band and the 1-0 vibrational transition for the B-X band. The reported investigations originate from CH-radical research in 1996 that constituted the first case of applying CRDS to the CH radical. The report also includes recent analysis that shows excellent agreement of measured and computed data, and it communicates CH line strength data.

Gravity played an important role in the development of life on earth. The effect of gravity on a living organisms can be investigated by controlling the magnitude of gravity. Most reduced gravity experiments are conducted on the lower earth orbit (LEO) in the International Space Station (ISS). However, running experiments in ISS face challenges such as high cost, extreme condition, lack of direct accessibility, and long waiting period. Therefore, researchers have developed various ground-based devices and methods to perform reduced gravity experiments. However, the search for life outside the earth requires more intensive research. Advancements in conventional methods and the development of new tools are required for this purpose. The advantages of Lab-on-a-Chip (LOC) devices make them an attractive option for simulating microgravity. This paper briefly reviews the advancement of LOC technologies for simulating microgravity in a earth-based laboratory.

Precision agriculture and open-source data repositories provide a plethora of field-specific ecological data about agroecosystems, but few mechanisms have been developed to turn that information into management recommendations for crop production. The On-Farm Precision Experiments (OFPE) framework is an agroecological model-based methodology to improve crop manager’s abilities to make field-scale agronomic input decisions. This work evaluates the use of field-specific experiments that employ open-source data and the data emanating from precision agriculture technologies to gain local knowledge of the spatial and temporal variability in agroeconomic performance at the sub-field scale. Quantification of the temporal variability in crop response to inputs (e.g., crop seeding rates, crop rotations, fertilizers, other soil amendments, pesticides, etc.) allows for estimation of the probability that a future management scenario will outcompete another, in terms of crop yield, crop quality, farmer net return, or environmental quality. The challenge is to integrate OFPE into applied management with minimal disruption of stakeholder practices while drawing on historic knowledge about the field and economic constraints. OFPE is the basis of a decision support system that includes a six-step cyclical process that harnesses precision agriculture technology to apply experiments and gather field-specific data, incorporates modern data management and analytical approaches, and generates management recommendations as probabilities of outcomes. The OFPE framework allows field managers to assess the tradeoffs in agronomic input management between the maximization of crop production, quality and profits from production while considering environmental effects.

This study presents a detailed assessment on the impact of the Brazilian legal framework related to the access and benefit sharing provisions of the UN Convention on Biological Diversity. The research is based on a comprehensive dataset that was systematically collected over several years, directly from the official government bodies responsible for its implementation. The aim of the study is to contribute to a fact-based discussion on the effectiveness of national ABS laws, focusing on the Brazilian legal framework, first established in the year 2000 and revised in 2015, as a case example. This study balances the costs and benefits of the Brazilian ABS system and assesses the regulatory challenges it poses to individuals, companies, and institutions that perform research, share knowledge, develop, manufacture or market products derived from Brazilian biodiversity. The study indicates that, after over 22 years of operation, the regulatory challenges are still real and relevant, and that the significant volume of data collected from users on access, prior commercialization and shipment of genetic materials abroad was never systematically assessed by the agencies in charge. Besides, it shows that the costs incurred by the government in managing the policy itself have been higher than the economic benefits it has made possible, and that the institutional mechanisms in place since 2015 have not been able to allocate the monetary benefits contributed by users to the National Benefit Sharing Fund to any projects aimed at developing sustainable uses or preserving Brazilian biodiversity.

Recently, there has been increasing attention toward inhaled nanoparticles (NPs) to develop in-halation therapies for diseases associated with the pulmonary system and investigate the toxic ef-fects of hazardous environmental particles on human lung health. Taking advantage of microfluidic technology for cell culture applications, lung-on-a-chip devices with great potential in replicating the lung air-blood barrier (ABB) have opened new research insights in preclinical pathology and therapeutic studies associated with aerosol NPs. Surprisingly, the air interface in such devices, which makes them tremendously unique among the other common liquid-based cellular mi-crosystems and enables exposure of cultivated cells to the drug/toxic aerosols, has been largely disregarded. Accordingly, there exists a significant research gap in the comprehensive under-standing of the NPs’ dynamics in the lung-on-a-chip devices, which is momentous to control the injection of aerosols to the target area and attain a desired physiochemical efficacy. To address this research gap, a numerical parametric study is presented to provide a deep insight into the dynamic behavior of the airborne NPs in a gas-liquid dual-channel lung-on-a-chip device with a porous membrane separating the channels. A finite element multi-physics model is developed to enable a particle tracing investigation simultaneously in both air and medium phases to replicate the in vivo conditions avoiding laborious and costly experimental trials. The results include the impact of fluid flow as well as geometrical properties on the distribution, deposition, and translocation of the NPs with diameters ranging from 10 nm to 900 nm in the lung-on-a-chip. The obtained results strongly suggest the aerosol injection of NPs instead of the aqueous solution for more efficient deposition on the substrate of the air channel and higher translocation to the media channel. The current study proposes to optimize the affecting parameters to control the injection and delivery of aerosol par-ticles into the lung-on-chip device depending on the objectives of biomedical investigations and provides optimized values for some specific cases. Therefore, this study can assist scientists and researchers in complementing their experimental investigation in future preclinical studies on pulmonary pathology associated with inhaled hazardous and toxic environmental particles, as well as therapeutic studies for developing inhalation drug delivery.

Herbs and Plants have been the most important form of medicine in India since ancient times. the plant kingdom is a goldmine of potential drugs and active molecules. Medicinal plants played a vital role in manufacturing human health and improving the quality of human life for thousands of years. During the last decade, the use of traditional medicine has expanded globally and gained popularity. Medicinal plants have healing properties due to the presence of various complex chemical substances of different compositions. Medicinal plants have served humans well as valuable components of medicines, flavorings, beverages, cosmetics, and dyes. Ficus religiosa is one of the medically important plants belonging to the family of Moraceae. It has been used broadly by Ayurvedic practitioners in India to treat various diseases. The present work is an endeavor to improve the effectiveness of synthetic drugs in combination with plant extracts.

Considering the actual world economical trends, one of the most important questions is now and in the future: how to reduce power consumption of electronic systems. Since the invention of computers, the electrical energy consumption step by step increased. Now when not only computers, but electric vehicles, robots, automation, and unmanned aerial vehicles play a very important role of our life, the main problem of system designers is how to reduce energy consumption in these systems. But also the existing already working systems must be revised in order to decrease their electric power consumption. The importance of this subject (energy control) shows that a huge number of research publications and survey papers deal with it. Just focusing on the last one or two years (2021 and 2022) the search hit 221000 titles (103000 hits only in 2022). Analyzing all the research areas is almost impossible, but focusing on some important research subjects, where one of the main topic is “energy saving methods” can give an overview about the subject. The paper focuses on the area of industrial robotic systems, electric vehicles, and embedded systems.

Cancer stem cells remain a challenge to isolate and characterize because of their plastic phenotype. Using a microfluidic lab-on-a-chip based on ultra-high frequency dielectophoresis, we measured the electromagnetic signature of colorectal cancer cells and demonstrated that cancer stem cells show a distinct and lower electromagnetic signature than differentiated cells. The release of extracellular vesicles from tumor cells can drive tumor progression and metastasis development. As extracellular vesicles from cancer stem cells carry more aggressive content, we treated colorectal cancer cells with these vesicles to test whether the lab-on-a-chip can detect a change in phenotype. The electromagnetic signature of treated cells is modified in comparison to untreated cells and sometimes even when no biological change is observed. The lab-on-a-chip provides rapid and relevant result without prior labeling compared to conventional biological approaches. It could be useful in the clinic for early detection of cancer stem cells in the tumor mass and for monitoring the aggressive potential of extracellular vesicles in the bloodstream in order to adapt therapeutic management and prevent relapse.

A variational analysis of dispersion medium (electrolytes and surfactants) was carried out for the best nucleotide interactions with the presence of nanoparticles and the ability to formation of homogeneous coatings upon drying / lyophilization. Using UV-spectroscopy and transmission electron microscopy, the processes of immobilization of nucleotides on the surface of nanoparti-cles of the composition ZrO2-3mol% Y2O3 (YSZ) in the presence of various dispersing agents were investigated. Promising dispersing agents were established, the optimal composition of suspen-sions based on DNA nucleotides and YSZ nanoparticles, which is potentially suitable for adaptive technologies of bionanoelectronics, was selected. The aim of the work is to obtain and study functional media for molecular electronics based on heterojunctions biological molecule – wide-gap dielectric.

Base on building information modeling(BIM) plus with Robotic process automation (RPA) technology is rapid development in smart building operations and maintenance (O&M). RPA is a workflow-based automated execution tool that is particularly well suited for replacing manual execution of simple and repetitive tasks using computer systems. The use of RPA technology can saves man-hours and increases productivity, which is important for the automation of building operations and maintenance operations.. The BIM technology, as an advanced technology in the construction industry, it can provide new ideas and methods for building operation and maintenance based on its visualization characteristics. That’s integrating RPA with BIM technology which will enhance the digitalization and virtualization of smart building operation and management. In this article will first introduce the features of RPA and BIM technology and then discuss the technical roadmap for remote automated operation and maintenance of smart building equipment room to implemention a low-cost and high efficient building equipment room operation and maintenance solution.

OBJECTIVE A quality improvement study to assess catheter-associated urinary tract infection (CAUTI) rate post-implementation of a bladder catheter with integrated active drain line urine clearance and automated intra-abdominal pressure monitoring in a burn intensive care unit (ICU). DESIGN Eight-year retrospective before and after study (2015–2022). SETTING A single American Burn Association verified Burn Center with fourteen inpatient beds. PATIENTS Patients meeting criteria for admission to a Burn Center METHODS Retrospective cohort study following the implementation of a novel urine output monitoring system with integrated drain line and urine clearance. Data from a 48-month (from January 2015-December 2018) historical control (period 1) were compared to data from a 28-month (from January 2020 to April 2022) post-implementation period (period 2). Pre- and post-implementation CAUTI event incidences were compared. Charts were reviewed to characterize the patients. RESULTS A total of 42 CAUTIs in 2243 patients were identified using the National Health and Safety Network (NHSN) definition during the analyzed period. There were 40 CAUTI events in period 1 and two CAUTIs in period 2. The incidence of CAUTI events pre-implementation was 0.030 (mean of 10 CAUTI events per year) compared to 0.002 (mean of 1 CAUTI event per year) post-implementation of an automatic drain line clearing UO monitoring system showing a significant reduction in CAUTI events (P<0.01, risk ratio novel vs. gravity bladder catheter 0.071, 95% confidence interval: 0.017-0.294). CONCLUSIONS CAUTIs were reduced in the period following the implementation of a novel urinary catheter system with an integrated active drain line and urine clearance in burn patients.

Technological advancements and innovations have profoundly changed the lives of people giving rise to smart environments, cities, and societies. As homes are the building block of cities and societies, smart homes are critical to establishing smart living and are expected to play a key role in enabling smart cities and societies. The current academic literature and commercial advancements on smart homes have mainly focused on developing and providing smart functions for homes to provide security management and facilitate the residents in their various activities such as ambiance management. Homes are much more than physical structures, buildings, appliances, operational machines, and systems. Homes are composed of families and are inherently complex phenomena underlined by humans and their relationships with each other, subject to individual, intragroup, intergroup, and intercommunity goals. There is a clear need to understand, define, consolidate existing research, and actualize the overarching roles of smart homes, the roles of smart homes that would serve the needs of future smart cities and societies. This paper introduces our data-driven parameter discovery methodology and uses it to provide, for the first time, an extensive, rather fairly comprehensive, analysis of the families and homes landscape seen through the eyes of academics and the public using over a hundred thousand research papers and nearly a million tweets. We develop a methodology using deep learning, natural language processing (NLP), and big data analytics methods and apply it to automatically discover parameters that capture a comprehensive knowledge and design space of smart families and homes comprising social, political, economic, environmental, and other dimensions. The 66 discovered parameters and the knowledge space comprising 100s of dimensions are explained by reviewing and referencing over 300 articles from the academic literature and tweets. The knowledge and parameters discovered in this paper can be used to develop a holistic understanding of matters related to families and homes facilitating the development of better, community-specific, policies, technologies, solutions, and industries for families and homes, leading to strengthening families and homes, and in turn, empowering sustainable societies across the globe.

Snow is a vital environmental parameter and dynamically responsive to climate change, particularly in mountainous regions. Snow cover can be monitored at variable spatial scales using Earth Observation (EO) data. Long-lasting remote sensing missions enable the generation of multi-decadal time series and thus the detection of long-term trends. However, there have been few attempts to use these to model future snow cover dynamics. In this study, we therefore explore the potential of such time series to forecast the Snow Line Elevation (SLE) in the European Alps. We generate monthly SLE time series from the entire Landsat archive (1985-2021) in 43 Alpine catchments. Positive long-term SLE change rates are detected, with the highest rates (5-8 m/y) in the Western and Central Alps. We utilize this SLE dataset to implement and evaluate seven uni-variate time series modeling and forecasting approaches. The best results were achieved by Random Forests, with a Nash-Sutcliffe efficiency (NSE) of 0.79 and a Mean Absolut Error (MAE) of 258 m, Telescope (0.76, 268 m), and seasonal ARIMA (0.75, 270 m). Since the model performance varies strongly with the input data, we developed a Combined forecast based on the best performing methods in each catchment. This approach was then used to forecast the SLE for the years 2022-2029. In the majority of the catchments the shift of the forecast median SLE level retained the sign of the long-term trend. In cases where a deviating SLE dynamic is forecast a discussion based on the unique properties of the catchment and past SLE dynamics is required. In the future, we expect major improvements in our SLE forecasting efforts by including external predictor variables in a multi-variate modeling approach.

Gene electrotransfer is one of the main non-viral methods for intracellular delivery of plasmid DNA, wherein pulsed electric fields are used to transiently permeabilize the cell membrane allowing enhanced transmembrane transport. By localizing the electric field over small portions of the cell membrane using nanostructured substrates, it is possible to increase considerably the gene electrotransfer efficiency while preserving cell viability. In this study, we design an electrotransfer approach based on commercially available cell culture inserts with polyethylene-terephthalate (PET) porous substrate. We first use multiscale numerical modelling to determine the pulse parameters, substrate pore size, and other factors that are expected to result in successful gene electrotransfer. Based on numerical results we design a simple device combining an insert with substrates containing pores with 0.4 um and 1.0 um diameter, a multiwell plate, and a pair of wire electrodes. We test the device in three mammalian cell lines and obtain transfection efficiencies similar to those achieved with bulk electroporation, but with low-voltage pulses that do not require the use of expensive electroporators. Our combined theoretical and experimental analysis calls for further systematic studies that will investigate the influence of substrate pore size and porosity on gene electrotransfer efficiency and cell viability.

Although the fusion energy sector is at a nascent stage, the private fusion energy market has grown. There are currently 38 private fusion energy companies around the world aiming to commercialise fusion energy in early 2030s and 2040s. Given the capability of fusion energy in transforming today’s energy paradigm and the global character of the market, it is important to analyse how these companies are interacting with international human rights standards. Therefore, this work investigates the involvement of the private fusion energy sector with two voluntary international initiatives in particular: the UN Global Compact and the UN Guiding Principles on Business and Human Rights (UNGP). This study attempts to answer two research questions: (i) Are private fusion energy companies participating in the UN Global Compact? (ii) How are private fusion energy companies publicly implementing the UNGP? Content analysis of secondary data collected from the UN Global Compact, Fusion Industry Association, ITER and companies’ official website as well as published reports is adopted. In summary, this work finds that private fusion energy companies are neither participants nor signatories of the UN Global Compact. Their observance of the UNGP is also very poor. This study contributes to the field by highlighting this gap which the private fusion energy companies need to consider and take measures in order to create a salutary human rights sector.

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

The way Norway is spearheading electrification in the transport sector is of global interest, and details of its policies and emission impacts represent a reference. We used the NERVE model, a bottom-up high-resolution traffic emission model, to calculate all exhaust emissions in Norway (2009-2020). This allows us to evaluate the co-benefit of policies to target climate change mitigation and air quality. We have analyzed local municipal data with regards to traffic growth, road network influences, vehicle composition, emissions and energy consumption. Light vehicle CO2 emissions per kilometre have been reduced by 22% since 2009, mainly driven by an increaseing bio-fuel mixing and BEV share. BEVs are mostly located in and around the main cities, areas with young vehicle fleets, and strong local incentives. Beneficiaries of all BEVs incentives have been a subset of the population with strong economic indicators. The incentivized growth in the share of diesel-fuelled passenger vehicle has been turned, and together with Euro6 emission standards, light vehicle NOx emissions have been halved since peaking in 2014. BEV represent an investment in emission reductions in years to come and current sales set up for an accelerated decline in emissions despite growth in traffic.

Understanding cell migration is a key step to unravel many physiological phenomena and predict several pathologies, like cancer metastasis. In particular, mechanical confinement has been proved to be a key factor in the cellular migration strategy choice. As our insight in the field improves, new tools are needed in order to empower biologists’ analysis capabilities. In this framework, microfluidic devices have been used to engineer the mechanical stimuli and to investigate cellular migration response in a more controlled way. In this work, we will review the existing technologies employed in the realization of microfluidic cellular migration assays, namely soft lithography of PDMS and hydrogels and femtosecond laser micromachining. We will give an overview of the state of the art of these devices, focusing on the different geometrical configurations that have been exploited to study specific aspects of cellular migration. Our scope is to highlight the advantages and possibilities given by each approach and to envisage the future developments in in-vitro migration studies under mechanical confinement in microfluidic devices.

African swine fever (ASF) is a notifiable viral disease of domestic and wild suids. Despite intensive re-search efforts, the pathogenesis of the disease is still far from being understood. Analysis of biomarkers in different body fluids may supplement traditional pathogenesis studies. As reliable protocols are often es-tablished in laboratories with lower biosafety, reliable inactivation of samples is crucial. The objective of this study was to find a procedure that inactivates the virus while preserving the biomarkers for down-stream analyses. To this means, three different inactivation protocols were employed, namely Tergitol-type NP-40 (NP-40) and polyoxyethylene-p-t-octylphenol (Triton X-100), respectively, and one with 95 °C heating. It could be demonstrated that all samples treated with 0.5% (v/v) concentration of both deter-gents showed absence of virus infectivity. The same was true for heated samples. However, heated serum was not suitable for analyses. Next, the treatment impact on biomarker readouts was assessed. While all protocols had an impact on the detection of biomarkers, correlation was retained. Especially NP-40 could be the desired detergent for more accurate measurements while achieving efficient virus inactivation. Based on these studies, samples can be reliably inactivated for most biomarker analyses and thus broader interdisciplinary cooperation is possible.

There is no formal difference between particles and black holes. This formal similarity lies in the intersection of gravity and quantum theory; quantum gravity. Motivated by this similarity, `wave-black hole duality' is proposed, which requires having a proper energy-momentum tensor of spacetime itself. Such a tensor is then found as a consequence of `principle of minimum gravitational potential'; a principle that corrects the Schwarzschild metric and predicts extra periods in orbits of the planets. In search of the equation that governs changes of observables of spacetime, a novel Hamiltonian dynamics of a Pseudo-Riemannian manifold based on a vector Hamiltonian is adumbrated. The new Hamiltonian dynamics is then seen to be characterized by a new `tensor bracket' which enables one to finally find the analogue of Heisenberg equation for a `tensor observable' of spacetime.

Transposable elements (TEs) ubiquitously exist in the human genome, and some have the ability to copy and paste themselves to other locations, resulting in new insertions. Organisms have evolved with mechanisms and machineries to repress such activity. TEs are also co-opted for beneficial functions by the host and are thus maintained in the genome. During the lifetime of humans, aberrant TE activity might cause or contribute towards diseases including neurological conditions such as Alzheimers Disease (AD) and cancer. While inflammatory pathways linked to TEs may be a part of the disease pathology, on the other hand altered TE activity involving inflammatory pathways could be recognised by disease suppression mechanisms. For this reason, TEs could be targeted for therapeutic applications aiming to prevent TE activity or reduce initial inflammatory pathways as well as to activate disease suppression mechanisms. In this review, we describe the contributory and potential preventative roles of TEs in neurological conditions and cancer from a molecular and evolutionary perspective. Evolutionary paradigms both at the unicellular and organismal level aid understanding the role of TEs in disease. These observations could pave the way for the development of novel therapeutic approaches targeting TEs.