Ombrian curves, i.e. curves linking rainfall intensity to return period and time-scale, are well-established engineering tools, crucial to the design against storm waters and floods. Whereas at-site construction of such curves is considered a standard hydrological task, it is a rather challenging one when large regions are of interest. Regional modelling of ombrian curves is particularly complex due to the need to account for spatial dependence together with the increased variability of rainfall extremes in space. We develop a framework for the parsimonious modelling of the extreme rainfall properties at any point in a given area. This is achieved by assuming a common ombrian model structure except for a spatially varying scale parameter which is itself modelled by a spatial smoothing model for the 24 h average rainfall maxima that employs elevation as an additional explanatory variable. The fitting is performed on the pooled all-stations data using an advanced estimation procedure (K-moments) that allows both for reliable high-order moment estimation and simultaneous handling of space-dependence bias. The methodology is applied in the Thessaly region, a 13 700 km2 water district of Greece characterized by varying topography and hydrometeorological properties.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

In recent years, distributed generation technology has developed rapidly. Renewable energy, represented by wind energy and solar energy, has been widely studied and utilized. In order to give full play to the advantages of Distributed Generation (DG) and meet the challenges after power grid access, Active Distribution Network (ADN) is considered as the future development direction of traditional distribution network because of its ability of active management. Nowadays, multi-scenario analysis is widely used in the research of optimal allocation of distributed power supply in active distribution network. Aiming at the problems that may arise when using multi-scenario analysis to plan DG with uncertainties in large-scale scenarios, a scenario reduction method based on improved clustering algorithm is proposed. The validity of the scene reduction method is tested, and the feasibility of the method is verified. At present, there are few studies on the optimal allocation of DG in ADN under fault state. In this paper, comprehensive safety indicators are introduced. Considering the timing characteristics of DG and the influence of active management mode, a bi-level programming model is established, which aims at minimizing the investment of annual life cycle and the removal of active power. The bi-level model is a complex mixed integer non-linear programming model. A hybrid algorithm combining cuckoo search algorithm and primal dual interior point method is used to solve the model. Finally, through the simulation of the IEEE-33 node system, the superiority of the scenario reduction method and the comprehensive security index used in this paper to optimize the configuration of DG in ADN is verified.

The paper proposes TOPSIS method for solving multi-objective multi-level programming problem (MO-MLPP) with fuzzy parameters via fuzzy goal programming (FGP). At first, - cut method is used to transform the fuzzily described MO-MLPP into deterministic MO-MLPP. Then, for specific , we construct the membership functions of distance functions from positive ideal solution (PIS) and negative ideal solution (NIS) of all level decision makers (DMs). Thereafter, FGP based multi-objective decision model is established for each level DM for obtaining individual optimal solution. A possible relaxation on decisions for all DMs is taken into account for satisfactory solution. Subsequently, two FGP models are developed and compromise optimal solutions are found by minimizing the sum of negative deviational variables. To recognize the better compromise optimal solution, the concept of distance functions is utilized. Finally, a novel algorithm for MO-MLPP involving fuzzy parameters is provided and an illustrative example is solved to verify the proposed procedure.

The South Asian economy is on the rise but struggling with power shortages and heavy dependence on fossil fuels. For sustained growth, there is a need for access to readily available energy sources, such as electricity. Trading clean electrical energy among neighbouring countries can ensure access to readily available points. South Asia has a diverse range of energy sources, including hydropower, that are available in the region. However, sectorial barriers can impede energy trading. This study has attempted to assess the readiness and barriers to Nepal’s cross-border energy trade with India and Bangladesh using the Analytic Hierarchy Process (AHP). This study also recommends possible measures to strengthen preparedness and address the challenges in energy trade that can be tailored and applied to other cross-country situations.

This work analyzes a new indoor laboratory data set looking at early fire indicators in controlled and realistic experiments representing different incipient fire scenarios. The experiments were performed within the confines of an indoor laboratory setting using multiple distributed sensor nodes on different room positions. Each sensor node collected data of particulate matter (PM), volatile organic compounds (VOC), CO, CO2, H2, UV, air temperature and humidity in terms of a multivariate time series. These data hold immense value for researchers within the machine learning and data science communities who are keen on exploring innovative advanced statistical and machine learning techniques. They serve as a valuable resource for the development of early fire detection systems. The analysis of the collected data was carried out in dependence of the manhattan distance between the fire source and the sensor node. We found that especially larger particles (> 0.5 μm) and VOCs show a significant dependency with respect to the intensity as a function of the manhattan distance to the source. Moreover, we observed differences in the propagation behavior of VOCs, PM, and CO, which are particularly relevant in incipient fire scenarios due to the presence of strand popagation effects.

We develop an interactive likelihood (ILH) for sequential Monte-Carlo (SMC) methods for image-based multiple target tracking applications. The purpose of the ILH is to improve tracking accuracy by reducing the need for data association. In addition, we integrate a recently developed deep neural network for pedestrian detection along with the ILH with a multi-Bernoulli filter. We evaluate the performance of the multi-Bernoulli filter with the ILH and the pedestrian detector in a number of publicly available datasets (2003 PETS INMOVE, AFL, and TUD-Stadtmitte) using standard, well-known multi-target tracking metrics (OSPA and CLEAR MOT). In all datasets, the ILH term increases the tracking accuracy of the multi-Bernoulli filter.

We report the results of an analysis of the functional capabilities of the KTP crystal and its isomorphs for nonlinear-optical frequency conversion of all types of interaction in the transparency range of the crystal. The possibility of implementing angle-, wavelength- (frequency-) and temperature-noncritical phase matching is shown.

The superharmonic imaging of tissue has the potential for high spatial and contrast resolutions, compared to the fundamental and second harmonic imaging. For this technique, the spectral bandwidth of an ultrasound transducer is divided for transmission of ultrasound and reception of its superharmonics (i.e., higher than the second harmonic). Due to the spectral division for the transmission and reception, transmitted ultrasound energy is not sufficient to induce superharmonics in media without using contrast agents, and it is difficult that a transducer has a -6-dB fractional bandwidth of higher than 100%. For the superharmonic imaging of tissue, thus, multi-frequency array transducers are the best choice if available; transmit and receive elements are separate and have different center frequencies. However, the construction of a multi-frequency transducer for intravascular ultrasound (IVUS) imaging is particularly demanding because of its small size of less than 1 mm. Here, we report a recently developed dual-element focused IVUS transducer for the third harmonic imaging of tissue, which consists of a 35-MHz element for ultrasound transmission and a 105-MHz element for third harmonic reception. For high quality third harmonic imaging, both elements were fabricated to have the same focus at 2.5 mm. The results of tissue mimicking phantom tests demonstrated that the third harmonic images produced by the developed transducer had higher spatial resolution and deeper imaging depth than the fundamental images.

The total lipid and protein content of the invasive caprellid amphipod Caprella scaura, from the biofouling communities of fish farm cages in the Pagasitikos Gulf were analyzed and compared among seasons. Proteins were the most abundant component (48.5 – 49.3%). Lipid content was relatively lower, with a wider range (6.7 – 34%) and showed a distinct seasonal fluctuation with high values in the winter population and a gradual decrease in spring and summer, with the lowest values in Autumn. Composition of the fatty acids profile was consistent among the seasons, with palmitic (16:0), Oleic (18:1n-9), Eicosapentanoic (20:5n-3)(EPA) and Docosahexanoic acid (22:6n-3 )(DHA) being the most abundant fatty acids. The presence of high levels of EPA and DHA fatty acids makes the species a potential candidate for use of these organisms in aquaculture.

Research into improving the functionality and capacities of wearable technology has surged as a result of its fast progress. The functioning of wearable technology is largely dependent on antenna design, which provides wireless connectivity and communication. This study of the literature searches many online sources for pertinent research on the various antenna designs for wearable technology. The findings verified that the materials vary based on the design being employed. An analysis was conducted on the gain, frequency, materials, and sizes. The review excels at synthesizing research and literature despite its restricted resources.

AbstraIncorporating knowledge of indigenous forage legumes or associated nutritional attributes in cultivated pastures has the potential to improve grazing conditions, rangeland conditions, and cattle productivity. Climate change and other site-specific factors such as land sizes and other grazing management practices play a significant role in food security, job creation, and environmental health. Several research results have reported that the utilization of forage legumes in most farming systems has proved to increase herbage yield and soil fertility. The major aim of this review is to elucidate the potential benefits of intercropping indigenous forage legumes such as cowpea (Vigna unguiculacta L.Walp) and Dolichols (Lablab purpureaus) intercropped with Chloris gayana, this is to assesses the principal advantages, productivity, and overall performance of forage legumes grown in conjunction with grasses. Moreover, this review seeks to provide insights into the optimal management practices for intercropping forage legumes with grasses. The promising feature of intercropping South African pastoral systems must target the ability of forage legumes in terms of performance and utilization of agro-symbiotic relationships of N2 fixation symbiotic relationship in pastures. Moreover, this review aims also to address this knowledge gap by assessing the effects of defoliation frequency on the biomass production of selected forage legumes when intercropped with Chloris gayana in different growing seasons. By examining how varying defoliation frequencies influence biomass production, this review aimed to provide practical recommendations for optimizing forage management practices and promoting sustainable forage production systems. Through this investigation, we can gain insights into the complex dynamics between the defoliation frequency, intercropping systems, and biomass production.

The earthquake alert of the early warning systems is based on the delay that the S waves have in reference to the P waves and on the interpretation of the P waves’ specific parameters. One of the most used parameters for estimating the moment magnitude of an earthquake is the characteristic period measured in the first 3 seconds of the appearance of the P wave. The typical method determines the characteristic period in the time domain, based on the velocity wave and the displacement wave. In the present work, we present a method for estimating the frequency of the characteristic period. This method includes zero padding of the P wave sequence, conversion of the extended sequence from the time domain to the frequency domain, the identification of local frequency maxima and the calculation of the weighted average of the frequency based on the identified maxima. Tests conducted on synthetic signals, as well as standard deviation evaluation tests for simultaneous recordings on several stations, reveal better performance to the usual method.

This paper considers the problem of predicting earthquakes. It uses a small amount of information to create a descriptive key that can be used as a footprint to describe an event. A frequency grid clusters events that occurred at the same time and then the algorithm averages the history of these events over preceding days, in particular the gaps when the events did not occur. The gaps are measured for the clustered events only and can be used to create a description that is quite unique. Results suggest that seismic events can in fact be traced using this key and subsequently recognised again, if the same conditions reoccur. They also suggest that force direction may be more important than magnitude, after the initial cluster selections are made. Greek and USA datasets have been looked at and the prediction accuracy can be 70% or better. The author therefore suggests that this is an interesting method that deserves attention.

This study explores the relationship between mental and physical therapeutic through three dimensions: man-environment relationships; a sense of place and symbolic landscapes. The study used a combination of qualitative and quantitative research methods. Local residents living in the coastal area of Xinglin Bay are the research objects. Quantitative data analysis revealed that the frequency of residents' visits was an important variable affecting their physical and treatment perceptions. In addition, the significance is higher for females than for males. The text analysis shows that the environment, especially the ecological restoration of water quality and migratory birds, is of great significance to the identity of local residents. Daily activities contribute to a sense of place and are what make the coast a place of therapeutic landscape function.

Modifiable THz spectral shapes are important tools that facilitate the comprehensive study of phonon dynamics in condensed matter systems. The generation of narrow bandwidth THz spectra with tunable center frequency which are suitable THz forms needed to achieve such objectives are currently less studied from the table top laser-induced plasma emitters’ perspective. This experimental research is aimed at developing a robust two-color laser induced plasma set-up comprising of a temporal pulse stretcher and an Optical Parametric Amplifier that generates chirped and wavelength tunable pulses respectively. By focusing and independently controlling the ω and 2ω arms of the chirped pulses resulting after the interaction with a β-BBO crystal, I aim to generate narrow bandwidth THz signal (from plasma) scalable at MV/cm intensity and tunable in a wide THz spectral range, in addition to varying the frequency ratio mix.

The vast rise in the number of Internet-connected devices necessitates a more accessible spectrum. As a result, Cognitive Radio was already proposed as a solution to the problem of restricted spectrum resources by utilizing available spectrum which is assigned to primary users. This method allows the secondary user to utilize the spectrum whenever the primary user is not using it, and it does so without intruding with the primary user. Whenever the secondary user detects the spectrum, it faced some issues, such as complexity in sensing leading to a lack of noise value, and the primary user is hidden to all secondary users. In order to tackle these challenges, an adaptive threshold matched filter detector and a cooperative matched filter detector are utilized in this paper to detect the spectrum. The probability of detection (Pd), probability of miss detection (Pm), and probability of false alarm (Pf) are the metrics used to assess sensing accuracy. To simulate suggested detectors, the MATLAB R2020a software was utilized. In comparison to earlier studies, the simulation conclusions reveal that the detection process starts with lower SNR values.

A The present investigation was undertaken in foothill regions of Uttarakhand from July-2016 up to December-2018. A total of thirty four different sites ranging from the roadside areas, grasslands to forests were studied and Mushroom fruiting bodies were collected. A total of One Hundred sixty six fruiting counts were obtained and 68 mushroom genera belonging to 15 orders and 43 families were identified. During collection visits mushroom were apparent from organic debris of diversified habitats ranging from humid soil; grassland; leaf litter; living tree trunk; dead wood log of forest zone. Maximum fruiting bodies (75%) were obtained between July to September and minimum i.e. 6% between November – February. Among the collected mushroom Stereum rugosum, Crepidotus variabilis, Laccaria laccata, Schizophyllum commune, Ganoderma applantum, Cantharellus cibarius were more prevalent. Out of all collected mushroom sample the frequency of Mushroom belonging to order Agaricales was 45.18% followed by Polyporales i.e., 27.7%. The collected mushroom were cultured on PDA medium and their mycelial forms were preserved for further studies.

Qualitative and quantitative values estimation is a crucial aspect of social data science and plays a vital role in social and psychological research. Numerous methods of personal values measurement such as Schwartz Value Survey (SVS) and its re-modified versions have been proposed and invented, but many are challenged with one or more limitations. In this article, an alternative approach in a new paradigm of values measurement called Kabiru’s Value Survey (KVS) was proposed to measure the relative degree of importance or significance attached to particular value-actions of an individual(s) in a given population over a period. The methodological innovations in KVS unlike other existing methods of human value measurement include the use of habitually reported practices associated with a particular value-action in place of judging the series of Schwartz hypothetical statements, the use of multiple dependent variables rather than a single coded hypothetical statement. In terms of data analysis, a new approach of multivariate compression is introduced which merges the chain of multiple dependent variables into one coded scale. Psychometric result interpretation is also another innovative aspect of KVS methodology. Finally, the proposed methodology however solved some of the criticized limitations of the other methods of human value measurement.

We report an all-optical radio-frequency (RF) spectrum analyzer with a bandwidth greater than 5 terahertz (THz), based on a 50-cm long spiral waveguide in a CMOS-compatible high-index doped silica platform. By carefully mapping out the dispersion profile of the waveguides for different thicknesses, we identify the optimal design to achieve near zero dispersion in the C-band. To demonstrate the capability of the RF spectrum analyzer, we measure the optical output of a femtosecond fiber laser with an ultrafast optical RF spectrum in the terahertz regime.

This paper studied the solar PV frequency control in the U.S. Eastern Interconnection (EI) and Texas Interconnection (ERCOT) systems. The studied frequency control approaches include droop frequency control, inertia control, and droop-inertia-combined frequency control. The control effects of different frequency controls of PV in the EI and ERCOT are studied using actual high PV penetration interconnection grid models to provide suggestions to the future revision of future PV frequency control standards.

Approximately 300 different types of blood groups are identified so far, the ABO and Rh antigens are still the clinically most significant and genetically most polymorphic of all human blood group systems to date. A total of 200 unrelated individuals from Uttar Pradesh were studied for the phenotype and allele frequency distribution of ABO and Rh (D) blood groups. In total 200 samples analyzed, phenotype B blood type has the highest frequency 36.5% (n=73), followed by O (34.5%; n=69), A (20.5%; n=41) and AB (8.5%; n=17). The O, A and B frequencies were 0.5849, 0.1571 and 0.2580 respectively. The overall phenotypic frequencies of ABO blood groups were B>O>A>AB. The variation in phenotypic frequencies between male and female might be due to small sample size of male sample. The allelic frequency of Rh-negative was 0.2.

This work examines drought and wet events based on Standardized Precipitation-Evapotranspiration Index (SPEI) over Kenya from 1981 to 2016. Spatiotemporal analysis of dry and wet events is conducted for 3 and 12-month SPEI. The drought incidences were observed during the period 1984, 1987, 2000, 2006, 2009, 2015, and 2016 for SPEI-3 whilst the SPEI-12 demonstrated the manifestation of drought during the year 2000 and 2006. SPEI clearly shows that the wettest period, 1997 and 1998 that coincide with the El Nino event in both time steps. SPEI -3 shows a reduction in moderate drought events while severe and extreme cases were on increase towards the end of the twentieth century. Conversely, SPEI-12 depicts an overall increase in severe drought occurrence over the study location with observed intensity of -1.54 and cumulative frequency of 64 months during the study period. The trend of wet events is upwards in the western and central highlands while the rest of the regions show increase in dry events during the study period. Moreover, moderate dry/wet events predominate whilst extreme events occur least frequent across all grid cells. It is apparent that the study area experiences mild extreme dry events in both categories although moderately severe dry events dominate most parts of the study area. High intensity and frequency of drought is noted in SPEI-3 while least occurrences of extreme events are recorded in SPEI-12. Although drought event prevails across the study area, there is evidence of extreme flood conditions over the recent decades. These findings form a good basis for next step of research that will look at projection of droughts over the study area based on regional climate models.

Methods of path integrals are used to develop multi-factor probabilities of bid-ask variables for use in high-frequency trading (HFT). Adaptive Simulated Annealing (ASA) is used to fit the nonlinear forms so developed to a day of BitMEX tick data. Maxima algebraic code is used to develop the path integral codes into C codes, and sampling code is used for the fitting process. After these fits, the resultant C code is very fast and useful for forecasting upcoming ask, bid, midprice, etc., when narrow and wide windows of incoming data are used. A bonus is the availability of canonical momenta indicators (CMI) useful to forecast direction and strengths of these variables.

Background: Variations in several clopidogrel-pharmacogenes have been linked to clopidogrel response variability and clinical outcomes. We aimed to determine the frequency distribution of major polymorphisms on CYP2C19, PON1, ABCB1 and P2RY12 pharmacogenes in Puerto Ricans. Methods: This was a cross-sectional, population-based study of 200 unrelated “Guthrie” cards specimens from newborns registered in the Puerto Rican Newborn Screening program (PRNSP) between 2004 and 2014. Taqman® SNP assay techniques were used for genotyping. Results: Minor Allele Frequencies (MAF) were 46% for PON1 (rs662), 41% for ABCB1 (rs1045642), 14% for CYP2C19*17, 13% for CYP2C19*2, 12% for P2RY12-H2 and 0.3% for CYP2C19*4. No carriers of the CYP2C19*3 variants were detected. All alleles and genotype proportions were found to be in Hardy-Weinberg equilibrium (HWE). Overall, there were no significant differences between MAFs of these variants in Puerto Ricans and the general population (n=453) of the 1,000 Genome project, except for the Yoruba in Ibadan from Nigeria (YRI, West-African ancestry; p<0.05). As expected, the prevalence of these markers in Puerto Ricans most resembled those in the 181 subjects from reference populations of the Americas. Conclusions: These prevalence data provide a necessary groundwork for future clinical studies of clopidogrel pharmacogenetics in Caribbean Hispanics.

Evaluation of the effect of a high frequency acceleration device on clear aligner exchange intervals and treatment time required to achieve prescribed tooth movements. Sixteen subjects with similar Class I malocclusions, 5mm or less crowding, and treated with Invisalign were divided into two groups. Group 1 (experimental; N=8) underwent aligner treatment in conjunction with daily use of the high frequency acceleration device and exchanged aligners every 5 days. Group 2 (controls; N=8) underwent aligner treatment without use of the device and exchanged aligners every 14 days according to the manufacturer's recommended interval. All subjects were treated by one investigator, and results were evaluated by both; total number of aligners used, and number of refinements required, prior to final Vivera retention scan. A significant decrease in both treatment time, and number of aligners required to complete treatment was observed by experimental subjects as compared to controls. In addition, no refinements were required by experimental subjects, whereas 6 of 8 of the control subjects required 1 or more refinements. Use of the high frequency acceleration device in conjunction with Invisalign treatment resulted in more predictable tooth movement and a significant decrease in the length of treatment.

Ambient vibration energy is widely being harnessed as a source of electrical energy to drive low-power devices. The vibration energy harvester (VEH) of interest employs an electromagnetic transduction mechanism, whereby ambient mechanical vibration is converted to electrical energy. The limitations affecting the performance of VEHs, with an electromagnetic transduction structure, include its operational bandwidth as well as the enclosure-size constraint. In this study, an analysis and design of a nonlinear VEH system is conducted, using the Output Frequency Response Function (OFRF) representations of the actual system model. However, the OFRF representations are determined from the Generalised Associated Linear Equation (GALE) decompositions of the system of interest. The effect of both nonlinear damping and stiffness characteristics, to respectively extend the average power and operational bandwidth of the VEH device, is demonstrated.

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

The development trends of the modern world of power electronics dictate the requirements for the use of AC voltage converters as soft starters for induction motors. A direct connection of the motors to the mains voltage negatively affects both the motor itself and the mains system as a whole due to high starting currents values, which entail, as a rule, more frequent accidents and shorter the drive system service life. The paper presents a study of the control system of a multi-zone AC voltage regulator. The use of capacitive voltage dividers will also compensate for the consumed reactive power. The article analyzes the features of modern soft starters, describes the circuit design, presents a mathematical calculation by the method of algebraization of differential equations, a performed simulation modeling in Matlab/Simulink, and also an assembled experimental stand for further research. Particular attention is paid to the definition of the multizonality concept of the proposed converter and the analysis of the control method. The developed algorithm of the double-loop automatic control system will minimize the influence of induction motors on the mains voltage, and thus improve electromagnetic compatibility.

This paper presents work done as part of a transformation effort towards a greener and more sustainable Aluminium manufacturing plant. The effort includes reducing the carbon footprint by minimising waste and increasing operational efficiency. The contribution of this work includes the reduction of waste through the implementation of autonomous, real-time quality measurement and classification at an Aluminium casthouse. Data is collected from the MV20/20 which uses ultrasound pulses to detect molten Aluminium inclusions, which degrade the quality of the metal and cause subsequent metal waste. The sensor measures cleanliness, inclusion counts and distributions from 20 - 160 microns. The contribution of this work is in the development of business analytics to implement condition-based monitoring through anomaly detection, and to classify inclusion types for samples that failed. For anomaly detection, multivariate K-Means and DBSCAN algorithms are compared as they have been proven to work in a wide range of datasets. For classification, a two-stage classifier is implemented. The first stage classifies the success or failure of the sample, while the second stage classifies the inclusion responsible for the failed sample. The algorithms considered include logistic regression, support vector machine, multi-layer perceptron and radial basis function network. The multi-layer perceptron offers the best performance using k-fold cross-validation, and is further tuned using grid search to explore the possibility of an even better performance. The results reveal that the model has achieved a global maximum in performance. Recommendations include the integration of additional sensor systems and the improvements in quality assurance practices.

This article proposes a measurement solution designed to monitor instantaneous frequency in power systems. It uses a data acquisition module and a GPS receiver for time stamping. A program in Python takes care of receiving the data, calculating the frequency, and finally transferring the measurement results to a database. The frequency is calculated with two different methods, which are compared in the article. The stored data is visualized using the Grafana platform, thus demonstrating its potential for comparing scientific data. The system as a whole constitutes an efficient low cost solution as a data acquisition system.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

One of the most important applications in the wireless sensor networks (WSN) is to classify mobile targets in the monitoring area. In this paper, a multi-DBN weighted voting classification algorithm is proposed on the basis of the Deep Belief Network (DBN) classifier and combined with the idea of voting method, which is implemented on the nodes of the WSN monitoring system by means of "upper training, lower transplantation" appraoch. The performance of the algorithm is verified by using real-world experimental data, and the results show that the proposed method has a higher accuracy in classifying the target signal features, achieving an average classification accuracy of 84.63% across four different types of moving targets. The experiment reveals that the multi-DBN weighted voting algorithm enhances the target classification accuracy by approximately 5% in comparison to the single DBN classifier, but the memory and computation time required for the algorithm to run are also increased at the same time. Compared to the FFNN classifier, which exhibited the highest classification accuracy among the four selected methods, the algorithm achieves an improvement of approximately 8.8% in classification accuracy. However, it incurs greater time overhead to run.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

Rapid assessment of maize yields in smallholder farming system is important to understand its spatial and temporal variability and for timely agronomic decision-support. Imageries acquired with unmanned air vehicles (UAV) offer opportunity to assess agronomic variables at field scale, however, it is not clear if this can be translated into reliable yield assessment on smallholder farms where field conditions, maize genotypes, and management practices vary within short distances. In this study, we assessed the predictability of maize grain yield using UAV-derived vegetation indices (VI), with(out) biophysical variables, in smallholder farms. High-resolution images were acquired with UAV-borne multispectral sensor at 4 and 8 weeks after sowing (WAS) on 31 farmers’ managed fields (FMFs) and 12 nearby Nutrient Omission Trials (NOT), all distributed across 5 locations within the core maize region of Nigeria. The NOTs included non-fertilized and fertilized plots (with and without micronutrients), sown with open-pollinated or hybrid maize genotypes. Acquired multispectral images were post-processed into several three (s) vegetation indices (VIs), normalized difference vegetation index (NDVI), normalized difference red-edge (NDRE), green-normalized difference vegetation index (GNDVI). Biophysical variables, plant height (Ht) and percent canopy cover (CC), were measured with the georeferenced plot locations recorded. In the NOTs, the nutrient status, not genotype, influenced the grain yield variability and outcome. The maximum grain yield observed in NOTs was 9.3 tha^-1, compared to 5.4 tha^-1 in FMF. Without accounting for between- and within-field variations, there was no relationship between UAV-derived VIs and grain yield at 4WAS (r<0.02, P>0.1), but significant correlations were observed at 8WAS (r≤0.3; p<0.001). Ht was positively correlated with grain yield at 4WAS (r=0.5, R²=0.25, p<0.001), and more strongly at 8WAS (r=0.7, R²=0.55, p<0.001), while relationship between CC and yield was only significant at 8WAS. By accounting for within- and between-field variations in NOTs and FMF (separately) through linear mixed-effects modeling, predictability of grain yield from UAV-derived VIs was generally (R²≤0.24), however, the inclusion of ground-measured biophysical variable (mainly Ht) improved the explained yield variability (R² ≥0.62, RMSEP≤0.35) in NOTs but not in FMF. We conclude that yield prediction with UAV-acquired imageries (before harvest) is more reliable under controlled experimental conditions (NOTs), than in actual farmer-managed fields where various confounding agronomic factors can amplify noise-signal within the vegetation canopy.

In this work, we show that a late fusion approach to multi-modality in sign language recognition improves the overall ability of the model in comparison to the singular approaches of Computer Vision (88.14%) and Leap Motion data classification (72.73%). With a large synchronous dataset of 18 BSL gestures collected from multiple subjects, two deep neural networks are benchmarked and compared to derive a best topology for each. The Vision model is implemented by a CNN and optimised MLP and the Leap Motion model is implemented by an evolutionary optimised deep MLP topology search. Next, the two best networks are fused for synchronised processing which results in a better overall result (94.44%) since complementary features are learnt in addition to the original task. The hypothesis is further supported by application of the three models to a set of completely unseen data where a multi-modality approach achieves the best results relative to the single sensor method. When transfer learning with the weights trained via BSL, all three models outperform standard random weight distribution when classifying ASL, and the best model overall for ASL classification was the transfer learning multi-modality approach which scored 82.55% accuracy.

This study presents an exact solution to the free vibration analysis of a uniform Timoshenko beam, with a harmonic vibration being assumed. The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. In this paper, a moment-shear force-circular frequency-curvature relationship was presented. The complete study was based on this relationship and closed-form expressions of efforts and deformations were derived. The free vibration response of single-span systems and spring-mass systems was analyzed; closed-form formulations of matrices expressing the boundary conditions were presented and the natural frequencies were determined by solving the eigenvalue problem. Systems with intermediate mass, spring, or spring-mass system were also analyzed. Furthermore, first-order dynamic stiffness matrices in local coordinates were derived. Finally, a second-order analysis of beams resting on an elastic Winkler foundation was conducted. The results obtained in this paper were in good agreement with those of other studies.

Finite element (FE) modeling is commonly used as a method to investigate the influence of medical devices, such as implants and screws and their effects on the biomechanical behavior of the spine. Another simulation method is a multi-body simulation (MBS), where the model is composed of several non-deformable bodies. MBS solvers generally require a very short computing time for dynamic tasks compared to an FE analysis. Considering this computational advantage, in this study, we examine whether parameters whose values are not known a priory can be determined with sufficient accuracy using MBS model. Therefore, we propose a Many-at-a-time sensitivity analysis method that allows approximating these a priory unknown parameters without requiring long simulation times. This method enables a high degree of MBS model optimization to be achieved in an iterative process. The sensitivity analysis method is applied to a simplified screw-vertebra model, consisting of an anterior anchor implant screw and vertebral body of C4. An experiment described in the literature is used as a basis for developing and assessing the potential of the method for sensitivity analysis and to validate the models action. The optimal model parameters for the MBS model were determined to be c=823224N/m for stiffness and d=488Ns/m for damping. The presented method of parameter identification can be used in studies including more complex MBS spine models or to set initial parameter values that are not available as initial values for FE models.

Multi-criteria decision analysis (MCDA), one of the prevalent branches of operations research, aims to design mathematical and computational tools for selecting the best alternative among several choices with respect to specific criteria. In the cloud, MCDA based online brokers uses customer specified criteria to rank different service providers. However, subjected to limited domain knowledge, the customer may exclude relevant or include irrelevant criterion, which could result in suboptimal ranking of service providers. To deal with such misspecification, this research proposes a model, which uses notion of factor analysis from the domain of unsupervised machine learning. The model is evaluated using two quality-of-service (QoS) based datasets. The first dataset i.e., feedback from customers, was compiled using leading review websites such as Cloud Hosting Reviews, Best Cloud Computing Providers, and Cloud Storage Reviews and Ratings. The second dataset i.e., feedback from servers, was generated from cloud brokerage architecture that was emulated using high performance computing (HPC) cluster at University of Luxembourg (HPC @ Uni.lu). The simulation runs in a stable cloud environment i.e. when uncertainty is low, shows that online broker (equipped with the proposed model) produces optimized ranking of service providers as compared to other brokers. This is due the fact that proposed model assigns priorities to criteria objectively (using machine learning) rather than using priorities based on subjective judgments of the customer. This research will benefit potential cloud customers that view insufficient domain knowledge as a limiting factor for acquisition of web services in the cloud.

Background: To compare the loss of preload in absence of loading and after a fixed number of ideal masticatory cycles in two different connection systems using all-on-four prosthetic model. Methods: Two equal models of an edentulous mandible rehabilitated with all-on-four technique with two types of abutment system (MUA and OT-Bridge) supporting a hybrid prosthesis, were used. Initial torque values of the prosthetic fixing screw, after ten minutes from initial screw tightening and after 400000 masticatory cycles were registered using a mechanical torque gauge. Differences between initial and final torque values were reported for each anchoring system and the two systems were finally compared. Results: No statistically significant differences regarding the loss of preload between MUA and OT-Bridge system were found after 400000 masticatory cycles; however, in MUA system it was found between anterior and posterior implant screws. A significant difference in preload loss was found only for MUA system comparing the initial screw torque to that measured after 10 minutes from the tightening in absence of cyclic loadings. Conclusions: MUA and OT-Bridge are reliable prosthetic anchoring systems able to tolerate repeated masticatory cycles also on distal cantilever in all-on-four rehabilitation model without any significant loss of preload in screw tightening

Numerous experimental and theoretical studies undertaken to determine the effective-stress coefficient for seismic velocities in rocks stem from the importance of this geomechanical parameter both for monitoring changes in rock saturation and pore pressure distribution in connection with reservoir production, and for overpressure prediction in reservoirs and formations from seismic data. The present work pursues a task to determine, in the framework of a low-frequency laboratory study, the dependence of the elastic moduli of n-decane saturated sandstone on the relationship between pore and confining pressures. The study was conducted on a sandstone sample with high quartz and notable clay content in the quasi-static regime, when the 100 ml tank filled with n-decane was directly connected to the pore space of the sample. The measurements were carried out at a seismic frequency of 2 Hz and strains, controlled by semiconductor strain gauges, not exceeding 10-6. The study was performed using a forced-oscillation laboratory apparatus utilizing stress-strain relationship. The dynamic elastic moduli have been measured in two sets of experiments: at constant pore pressures of 0, 1 and 5 MPa and differential pressure (defined as a difference between confining and pore pressures) varied from 3 to 19 MPa; and at а constant confining pressure of 20 MPa and pore pressure varied from 1 to 17 MP. It was shown that the elastic moduli obtained in the measurements are in good agreement with the Gassmann moduli calculated for the range of differential pressures used in our experiments, which corresponds to the effective-stress coefficient equal to unity.

Predicting and evaluating the vitality level of public spaces of urban design is crucial before new construction and renewal, especially for developing countries, to avoid failures like "ghost neighborhood" and reduce resource waste. However, existing assessment methods for the urban vitality are either static and ignore changes in the time dimension, or rely on historical big data and are unable to predict unbuilt projects. This study combines previous methods and crowds’ characteristics observation in public space, puts forward the crowd-frequency hypothesis and constructs an algorithm, and establishes a time-dimensional urban vitality dynamic prediction model. Taking the Rundle Mall neighborhood in Adelaide, Australia, as an example, the effec-tiveness of the prediction model was proved through on-site observation sampling comparative verification method. In addition, the decision tree model was used to conduct machine learning on the case data, and a set of algorithm programs were obtained that can directly input some basic information to obtain the urban vitality level (high-medium-low) in a certain period. It can be used as a tool to support the design and decision-making processes of urban planners and government officials, providing a low-cost way to achieve sustainable urban vitality construction of late-developing cities directly.

We are currently investigating the ultrasound imaging of a sensor consisting of a randomized encoding mask attached to a single lead zirconate titanate (PZT) oscillator for use in a puncture microscope. The proposed model was performed using a finite element method (FEM) simulator. To increase the number of measurements required by a single element system, the transducer was rotated at different angles. The image was constructed by solving a linear equation of the image model. In a previous study, the image resolution was improved by extracting phase information. In this study, we propose a strategy by integrating the weighted frequency subbands compound and a super resolution method (SCM) to improve the resolution in range and lateral resolution. We also evaluated the image performance by applying different methods to improve the image quality. The results show that better image resolution and speckle suppression were obtained by applying the proposed method.

Six mode shapes, including bending and torsion, were documented for five different basketball rims and backboards at the United States Military Academy, West Point, New York, USA. The frequency and damping ratio of each mode shape were also determined. The empirical process began with the time-domain excitation and response of each rim-backboard system. The impulse of excitation came from an impact hammer separately applied to sequentially, to each node. The sinusoidal response was gathered from an accelerometer at a fixed location, node 1. Each time-domain excitation-response was then converted to a frequency domain Bode plot for each node by a B&K 2034 Signal Analyzer, giving transfer functions of output/input versus frequency. Structural Measurements System (SMS) Software was used to fit mode shapes to the Bode plots. Each of the six mode shapes were fitted to the Bode plots of each node at a specific modal frequency. Each of the six mode shapes were a function of the locations of the nodes, and the Bode plot gathered at each node. The first and second modes were critical for showing that the Energy Rebound Testing Device statistically correlated with the energy transferred to the rim and backboard. A known perturbation mass was selectively attached to the rim, to help isolate the dynamic masses and spring rates for the rim and backboard, to ascertain the kinetic energy transferred to the rim had a 95.67% inverse correlation with rim stiffness.

Dietary fiber has been associated with health benefits, therefore, the availability of validated tools to assess food consumption associated with high-fiber foods would allow the quantification of the intake of this functional nutrient, the identification of risk groups and target populations, and the development of public policies and/or programs aimed at improving the health of the population. In this study, a fiber intake short food frequency questionnaire (FFQ) was translated into Spanish and its content validity was determined by a group of experts, to subsequently conduct a pilot test including 198 subjects aged 36+12.5 years, residing in Chile (46 men and 150 women), with the purpose of quantifying dietary fiber intake. The global assessment of the FFQ revealed a validity coefficient of 0.98+0.02; after the application of the pilot, mean dietary fiber intake in adult Chilean residents was of 13 g per day, with similar results to those found in the National Food Consumption Survey 2010 (12.5 g per day in men, and 11.5 g in women). The FFQ is a quick and valid tool to classify people on the basis of their habitual dietary fiber intake.

Classical numerical methods for solving ordinary differential equations often produce less accurate results when applied to problems with oscillatory or periodic behaviour. To adapt them for such problems, they are usually modified using the exponential fitting technique. This adaptation allows for the construction of new methods from their classical counterparts. The new methods are usually more accurate, efficient and suitable for handling the oscillatory or periodic behaviour of the problem. In this work, we construct a two-parameter exponentially-fitted Taylor method suitable for solving oscillatory or periodic problems that possess two frequencies. The construction algorithm is based on a proposed six-step flowchart discussed by authors in related literature. Two standard test problems were used to illustrate the accuracy and performance of the proposed method.

The increasing penetration of renewable energy sources in power grids highlights the role of battery energy stor- age systems (BESSs) in enhancing the stability and reliability of electricity. A key challenge with the renewables’, specially the BESSs, integration into the power system is the lack of proper dynamic model for stability analysis. Moreover, a proper control design for the power system is a complicated issue due to its complexity and inter-connectivity. Thus, the application of decentralized control to improve the stability of a large- scale power system is inevitable, especially in distributed energy sources (DERs). This paper presents an optimal distributed hybrid control design for the interconnected systems to suppress the effects of small disturbances in the power system employing utility-scale batteries based on existing battery models. The results show that i) the smart scheduling of the batteries’ output reduces the inter-area oscillations and improves the stability of the power systems; ii) the hybrid model of the battery is more user-friendly compared to the Western electricity coordinating council (WECC) model in power system analysis.

This paper proposes a forecast-centric adaptive learning model that engages with the past studies on the order book and high-frequency data, with applications to hypothesis testing. In line with the past literature, we produce brackets of summaries of statistics from the high-frequency bid and ask data in the CSI 300 Index Futures market and aim to forecast the one-step-ahead prices. Traditional time series issues, e.g. ARIMA order selection, stationarity, together with potential financial applications are covered in the exploratory data analysis, which pave paths to the adaptive learning model. By designing and running the learning model, we found it to perform well compared to the top fixed models, and some could improve the forecasting accuracy by being more stable and resilient to non-stationarity. Applications to hypothesis testing are shown with a rolling window, and further potential applications to finance and statistics are outlined.

We show broadband sum-frequency generation (SFG) in the Green-Yellow-Orange-Red spectral range using bismuth triborate, BiB3O6 crystal (BIBO) as nonlinear material. We perform a noncollinear phase-matching configuration within BIBO crystal using the remaining light behind the second harmonic generation stage and the infrared idler of an optical parametric amplifier (OPA). The obtained mixing radiation of ultrafast light sources to generate femtosecond pulses across 520.5 to 742.5 nm region is observed. SFG spectrum from single-pass cross-correlation intensity over such visible range is showed. The SFG wavelengths as a function of tunable wavelength idler OPA agrees with the expectations of parametric conversion condition and open the door to practical multi-beam or multi-color sum-frequency generators.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

We report a broadband radio frequency (RF) channelizer with up to 92 channels using a coherent microcomb source. A soliton crystal microcomb, generated by a 49 GHz micro-ring resonator (MRR), is used as a multi-wavelength source. Due to its ultra-low comb spacing, up to 92 wavelengths are available in the C band, yielding a broad operation bandwidth. Another high-Q MRR is employed as a passive optical periodic filter to slice the RF spectrum with a high resolution of 121.4 MHz. We experimentally achieve an instantaneous RF operation bandwidth of 8.08 GHz and verify RF channelization up to 17.55 GHz via thermal tuning. Our approach is a significant step towards the monolithically integrated photonic RF receivers with reduced complexity, size, and unprecedented performance, which is important for wide RF applications ranging from broadband analog signal processing to digital-compatible signal detection.

The exact etiology of myopia remains elusive. The author proposes the particle property of photon in living tissue and the photon-electron theory in living tissue, if the frequency of the photon exceeds the threshold, the photon has enough energy to strike the electron away and forms a hole of a diameter in photon diameter scale in living tissue include the eye. Longer time of high-frequency electromagnetic radiation will cause more holes and a larger radius of holes. The visual light which passes through the radiated hole in the eye cannot be refracted on the macula, this is myopia symptom of blurred vision, shortening the distance of the eye and the object will include more visual light into cornea and lens, this is myopia another symptom of nearsightedness. The particle property of photon causes elongation of the eye and the macular holes.Blue light and X-ray are two kinds of high-frequency electromagnetic radiation which can shot holes in eye and cause myopia.

This paper proposes a novel deterministic methodology for estimating the optimal sampling frequency (SF) of water quality monitoring systems. The proposed methodology is based on employing two-dimensional contaminant transport simulation models to determine the minimum SF considering all the potential changes in the boundary conditions of a water body. A two-dimensional contaminant transport simulation model (RMA4) was implemented to estimate the distribution patterns of the total dissolved solids (TDS) within the Al-Hammar Marsh in the southern part of Iraq for 30 cases of potential boundary conditions. Using geographical information system (GIS) tools, a spatiotemporal analysis approach was applied to the results of the RMA4 model to determine the minimum SF of the monitoring stations with an accuracy level of detectable change in TDS concentration (ALC) of 5%, 10% and 15%. The proposed methodology specified a minimum and maximum SF for each monitoring station (MS) that ranged between 12 and 33 times per year, respectively. Additionally, increasing the ALC to 10% and 15% increase the minimum SF for some MSs by approximately 18% and 21%, respectively. However, the proposed methodology includes all the potential values and cases of boundary conditions, which increases the certainty of monitoring the system and the efficiency of the SF schedule. Moreover, the proposed methodology can be effectively applied to all types of surface water resources.

Evaluation of the effects of a high-frequency acceleration (HFA) device on patient pain response to orthodontic forces. A multi-centered trial investigating pain sensitivity to orthodontic forces on 75 subjects at 4 study centers. Subjects underwent clear aligner treatment, with or without adjunctive HFA and documented their pain intensity using the validated NRS10 numeric rating scale. In-Office and At-Home ratings were measured separately for each subject for immediate and extended effect evaluations. Use of HFA devices in conjunction with clear aligner orthodontic treatment demonstrated significant reduction in subjects’ recorded pain ratings vs controls within 5 minutes of aligner exchange, (p = 0.006) and significant reduction in recorded pain ratings vs controls over a 7-day period following aligner exchange (p = 0.018). A 99.6% daily compliance rate with at home use of the HFA device was recorded for all subjects in the study. HFA significantly reduces pain attributed to orthodontic force. HFA delivers clinically significant immediate pain relief, and clinically significant extended pain relief over the 7 days following adjustment.

Introduction The prevalence of adolescent electronic cigarette (e-cigarette) use has increased in most countries. This study determines the relation between the frequency of e-cigarette use and the frequency and intensity of cigarette smoking. Furthermore, it evaluates the association between the reasons for e-cigarette use and the frequency of its use. Materials and Methods Participants were 68,043 middle and high school students aged 13–18 years from the 2015 Korean Youth Risk Behavior Web-Based Survey. Of the 68,043 participants, we analyzed 6,655 adolescents with an experience of e-cigarette use. Results The prevalence of ever using and current (past 30 days) use of e-cigarettes was 10.1% and 3.9%, respectively. Of the ever e-cigarette users, approximately 40% used e-cigarettes for ≥1/month and 8.1% used e-cigarettes daily. Daily e-cigarettes users were 10 times greater among daily cigarette smokers than among cigarette users for <1/month (18.1% vs. 1.8%) and 16 times more prevalent among those smoking ≥20 cigarettes/day than among those smoking <1 cigarette/month (38.9% vs. 2.4%). The most common reason for e-cigarette use was curiosity (22.9%), followed by less harmful than conventional cigarettes (18.9%), smoking cessation (13.1%), and indoor use (10.7%). Curiosity was the most common reason among less frequent e-cigarette users; however, smoking cessation and indoor use were the most common reasons among more frequent users. Conclusions Results showed a positive relation between frequency or intensity of conventional cigarette smoking and frequency of e-cigarette use among Korean adolescents, and frequency of e-cigarette use differed according to the reason for the use of e-cigarettes.

In this study, an optimized multi-material system was designed and developed to print samples in various applications, including biomedical fields (e.g., mandibular bone loss). To improve the mechanical and biological properties of scaffolds utilized for dental bone loss applications, a multi-material setup was devised, which employs digital light processing technology. This setup consists of a linear system comprising two resin vats and one ultrasonic cleaning tank, enabling the integration of diverse materials and structures to optimize the composition of the scaffold. This approach was used to print multi-material PLLA scaffolds containing 20 wt.%. HA on the interior side, and PLLA containing 1 wt.% GO on the exterior surface of the scaffold, which were evaluated mechanically and biologically after printing. The scaffold was designed using a triply periodic minimal surface (TPMS) lattice structure, which is known to possess favorable mechanical and biological properties. Various multi-material samples were successfully printed and evaluated to illustrate the multiple-material setup's potential for ensuring proper function, cleaning, and adequate interface bonding. By numerically evaluating several TMPS structures, a novel Gyroid TPMS scaffold with a nominal porosity of 50% was developed and validated experimentally. The biological properties of the scaffolds were also evaluated, including surface morphology, (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) MTT assay, and cell adhesion. Based on the results, multi-material components with the least contaminations with suitable mechanical and biological properties were successfully printed. By combining PLLA-HA and PLLA-GO, this innovative technique holds tremendous potential for enhancing the effectiveness of regenerative procedures in the field of dentistry.

Urgent environmental challenges and emerging additive manufacturing (AM) technologies push research towards more performant and new materials. In the field of metallurgy, high entropy alloys (HEAs) have recently represented a topic of intense research because of their promising properties, such as high temperature strength and stability. Moreover, this class of multi-principal element alloys (MPEAs) have opened up researcher community to unexplored compositional spaces, making prosper literature of high-throughput methodologies and tools for rapidly screening large number of alloys. However, none of the methods has been aimed to design new MPEAs for AM process known as selective laser melting (SLM) so far. Here we conducted nanoindentation testing on single scan tracks of elemental powder blends and pre-alloyed powders after ball milling of AlTiCuNb and AlTiVNb. Results show that nanoindentation can represent an effective technique to gain information about phase evolution during laser scanning, contributing to accelerate the development of new MPEAs.

Smart Internet of Vehicles (IoVs) combined with Artificial Intelligence (AI) will contribute to vehicle decision-making in the Intelligent Transportation System (ITS). Multi-Vehicle Pursuit games (MVP), a multi-vehicle cooperative ability to capture mobile targets, is becoming a hot research topic gradually. Although there are some achievements in the field of MVP in the open space environment, the urban area brings complicated road structures and restricted moving spaces as challenges to the resolution of MVP games. We define an Observation-constrained MVP (OMVP) problem in this paper and propose a Transformer-based Time and Team Reinforcement Learning scheme (T3OMVP) to address the problem. First, a new multi-vehicle pursuit model is constructed based on decentralized partially observed Markov decision processes (Dec-POMDP) to instantiate this problem. Second, by introducing and modifying the transformer-based observation sequence, QMIX is redefined to adapt to the complicated road structure, restricted moving spaces and constrained observations, so as to control vehicles to pursue the target combining the vehicle’s observations. Third, a multi-intersection urban environment is built to verify the proposed scheme. Extensive experimental results demonstrate that the proposed T3OMVP scheme achieves significant improvements relative to state-of-the-art QMIX approaches by 9.66%~106.25%. Code is available at https://github.com/pipihaiziguai/T3OMVP.

Abstract: Thermal desalination is yet a reliable technology in the treatment of brackish water and seawater; however, its demanding high energy requirements have lagged it compared to other non-thermal technologies such as reverse osmosis. This review provides an outline of the development and trends of the three most commercially used thermal or phase change technologies worldwide: Multi Effect Distillation (MED), Multi Stage Flash (MSF), and Vapor Compression Distillation (VCD). First, state of water stress suffered by regions with little fresh water availability and existing desalination technologies that could become an alternative solution are shown. The most recent studies published for each commercial thermal technology are presented, focusing on optimizing the desalination process, improving efficiencies, and reducing energy demands. Then, an overview of the use of renewable energy and its potential for integration into both commercial and non-commercial desalination systems is shown. Finally, research trends and their orientation towards hybridization of technologies and use of renewable energies as a relevant alternative to the current problems of brackish water desalination are discussed. This reflective and updated review will help researchers to have a detailed state of the art of the subject and to have a starting point for their research, since current advances and trends on thermal desalination are shown.

Electric moped scooter sharing services have recently experienced strong growth rates, particularly in Europe. Due to their compactness, environmental-friendliness and convenience, shared e-mopeds are suitable modes of transport in urban mobility to help reduce the environmental impact. However, its traffic-related, economic and environmental effects are merely represented in academic research. We used passenger car traffic data in Berlin generated by the multi-agent transport simulation framework MATSim to develop a python-based simulation, resembling an e-moped sharing system. Based on the results, a total cost of ownership and a life cycle assessment for fleet sizes of 2,500, 10,000 and 50,000 vehicles were conducted. The results indicate that a substantial part of all passenger car trips in Berlin can be substituted. The larger the fleet, the more and longer trips are replaced. Simultaneously, the efficiency in terms of fleet utilization decreases. The scenario with 10,000 e-mopeds offers the lowest total distance-based costs for sharing operators, whereas a fleet consisting of 2,500 vehicles exhibits the lowest environmental emissions per kilometer driven over the expected lifespan of a shared e-moped. Based on the renewable energy potential for 2050 forecasted by the German Federal Environment Agency, a significant overall decline in environmental impacts can be achieved.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

Artificial Intelligence (AI) and Deep Reinforcement Learning (DRL) have revolutionised e-learning by creating personalised, adaptive, and secure environments. However, challenges such as privacy, bias, and data limitations persist. E-FedCloud aims to address these issues by providing more agile, personalised, and secure e-learning experiences. This study introduces E-FedCloud, an AI-assisted adaptive e-learning system that automates personalised recommendations and tracking, thereby enhancing student performance. It employs federated learning-based authentication to ensure secure and private access for both course instructors and students. Intelligent Software Agents (ISAs) evaluate weekly student engagement using the Shannon Entropy method, classifying students into either engaged or not-engaged clusters. E-FedCloud utilises weekly engagement status, demographic information, and an innovative DRL-based early warning system, specifically ID2QN, to predict the performance of not-engaged students. Based on these predictions, the system categorises students into three groups: risk of dropping out, risk of scoring lower in the final exam, and risk of failing the end exam. It employs a multi-disciplinary ontology graph and an attention-based capsule network for automated, personalised recommendations. The system also integrates performance tracking to enhance student engagement. Data is securely stored on a blockchain using the LWEA encryption method.

There are currently around 78 Nuclear Power Plants (NPP) in the world based on Boiling Water Reactors (BWR). The current parameter to assess BWR instability issues is the linear Decay Ratio (DR). However, it is well known that BWRs are complex non-linear dynamical systems that may even exhibit chaotic dynamics that normally preclude the use of the DR when the BWR is working at a specific operating point during instability. In this work a novel methodology based on an adaptive Shannon Entropy estimator and on Noise Assisted Empirical Mode Decomposition variants is presented. This methodology was developed for real-time implementation of a stability monitor. This methodology was applied to a set of signals stemming from several NPPs reactors (Ringhals-Sweden, Forsmark-Sweden and Laguna Verde-Mexico) under commercial operating conditions, that experienced instabilities events, each one of a different nature

Water area segmentation in remote sensing is of great importance for flood monitoring. To overcome some challenges in this task, we construct the Water Index and Polarization Information (WIPI) multi-modality dataset and propose a multi-Modality Fusion and Gated multi-Filter U-Net (MFGF-UNet) convolutional neural network. The WIPI dataset enhances the water information and reduces the data dimension. In particular, the Cloud-Free label provided in the database effectively mitigates the issue of scarcity of labeled samples Since a single form or uniform kernel size cannot handle the variety in size and shape of water bodies, we proposed the gated multi-filter inception (GMF-Inception) module in our MFGF-UNet. Moreover, we utilize the attention mechanism by introducing the Gated Channel Transform (GCT) skip connection and integrating GCT into GMF- Inception to further improve model performance. Extensive experiments on three benchmarks, including WIPI, Chengdu and GF2020 datasets demonstrate that our method achieves favorable performance with lower complexity and better robustness against six competing approaches. For example, on WIPI, Chengdu and GF2020 datasets, the proposed MFGF-UNet model achieves F1 of 0.9191, 0.7410, and 0.8421, respectively, which average F1 on three datasets is 0.0045 higher than the U-Net model and reduces 62% average GFLOPs. New WIPI dataset, code and trained models have been released on GitHub

Real-world optimization problems are often governed by one or more constraints. Over the last few decades, extensive research has been performed in Constrained Optimization Problems (COPs) fueled by advances in computational intelligence. In particular, Evolutionary Algorithms (EAs) are a preferred tool for practitioners for solving these COPs within practicable time limits. We propose an ensemble of multi- method hybrid EA framework with four mutation operators, two crossover operators, multi-search [Differential Evolution (DE) & Gaining Sharing Knowledge (GSK)] optimization algorithm, and ensemble of constraint handling techniques to solve global real- world constrained optimization problem. The proposed frame- work FEPEA has an ascendancy of multiple adaptation strategies concerning the control parameters, search mechanisms, two sub-populations as well as uses knowledge sharing mechanism between junior and senior phases. The algorithm also combines the power of four popular constraint handling techniques (CHT) and uses a voting mechanism to select any particular CHT. On top of that, this algorithm also uses both linear and non- linear population size reduction in every step of the evolutionary process. We test our method on 57 real-world problems provided as part of the CEC 2020 special session & competition on real- world constrained optimization benchmark suite. Experimental results indicate that FEPEA is able to achieve state-of-the- art performance on real-world constrained global optimization when compared against other well-known real-world constrained optimizers.

The hybrid bond graph has been studied in depth for scalar bond graphs, but how does this translate to the multi-bond graph? Here, the controlled junction – used to model structural switching such as contact – is extended to the multi-bond case. This is a simple process, assuming that all bonds switch simultaneously (which makes physical sense). A controlled 0-junction is applied to multi-bond graph of a car, which can lose contact with the ground in cornering. Dynamic causality features, but this can be accommodated using an equational submodel in 20-Sim (in a manner similar to that used with scalar bond graphs). The junction is proposed for subsequent work to develop a validated multi-body dynamics car model in cornering.

The quality of digital elevation models (DEMs) is inevitably affected by the limitations of the imaging modes and the generation methods. One effective way to solve this problem is to merge the available datasets through data fusion. In this paper, a fusion-based global DEM dataset (82°S-82°N) is introduced, which we refer to as GSDEM-30. This is a 30-m DEM mainly reconstructed from the unfilled SRTM1, AW3D30, and ASTER GDEM v2 datasets combining the multi-source and multi-scale fusion techniques. A comprehensive evaluation of the GSDEM-30 data, as well as the 30-m ASTER GDEM v2 and AW3D30 DEM, was presented. Global ICESat GLAS data and the local National Elevation Dataset (NED) were used as the reference for the vertical accuracy validation, while GlobeLand30 was introduced for the landscape analysis. Furthermore, we employed the maximum slope approach to detect the potential artefacts in the DEMs. The results show that the GDEM data are seriously affected by noise and artefacts. With the advantage of the multiple datasets and the refined post-processing, the GSDEM-30 are contaminated with fewer anomalies than both ASTER GDEM and AW3D30. The fusion techniques used can also be applied to the reconstruction of other fused DEM datasets.

The framework of product life cycle (PLC) cost analysis is one of the most important evaluation tools for a contemporary high-tech company in an increasingly competitive market environment. The PLC-purchasing strategy provides the framework for a procurement plan and examines the sourcing strategy of a firm. The marketing literature emphasizes that ongoing technological change and shortened life cycles are important elements in commercial organizations. From a strategic viewpoint, the vendor has an important position between supplier, buyer and manufacturer. The buyer seeks to procure the products from a set of vendors to take advantage of economies of scale and to exploit opportunities for strategic relationships. However, previous studies have seldom considered vendor selection (VS) based on PLC cost (VSPLCC) analysis. The purpose of this paper is to solve the VSPLCC problems considering the situation of a single-buyer-multiple-supplier. For this issue, a new VSPLCC procurement model and solution procedure are derived by this paper to minimize net cost, rejection rate, late delivery and PLC cost subject to vendor capacities and budget constraints. Moreover, a real case in Taiwan is provided to show how to solve the VSPLCC procurement problem.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

This study compared cortical responses to speech in preschoolers with typical language development (TLD) and Developmental Language Disorder (DLD), and in adults. We investigated whether top-down language effects modulate speech perception in an adult-like manner. We compared cortical mismatch responses (MMR) during passive perception of speech differing in linguistic complexity in three groups of participants: preschoolers with TLD (n=11), preschoolers with DLD (n=16) and adults (n=20). We also measured children’s phonological skills and investigated if they are associated with the cortical responses. MMR results indicated top-down language effects in adults, with enhanced cortical discrimination of lexical stimuli but not of non-words. In preschoolers, the TLD and DLD groups did not differ on the MMR measures and no top-down effects were detected. Moreover, we found no association between MMRs and phonological awareness skills, even though the DLD group’s phonological skills were significantly lower. Our findings suggest that top-down language modulations on speech discrimination may not be present during early childhood, and that children with DLD may not exhibit cortical speech perception deficits. The lack of association between phonological and MMR measures indicates that further research is needed to understand the link between language skills and cortical activity in preschoolers.

The vibration response of soil is a key property in the field of agricultural soil tillage. Vibration components of tillage machinery are generally used to reduce tillage resistance and improve work efficiency, the pressure variation under low-frequency vibration will affect the fragmentation and dispersion of farmland soil. However, the gradient of pressure variation, frequency domain response, and effective transmission range are unclear. A new method based on DEM (Discrete Element Method) is presented to study the vibration response and pressure transmission under low-frequency vibration. Bench test results showed that peak pressure positively correlates with the vibration frequency and attenuates rapidly at the vibration distance of 100 to 250 mm. The results data were also selected to determine the simulation model parameters. Amplitude, vibration frequency, and soil depth were used as test factors in single-factor simulation tests, and their effects on the peak pressure, frequency domain response, and effective transmission distance were analyzed. The results showed a positive relationship between the peak pressure and the test factors. The peak pressure increases with a maximum gradient of 19.02 kPa/mm at a vibration distance of 50 mm. The amplitude, vibration frequency, and soil depth positively correlate with the dominant frequency amplitude. The main frequency is independent of amplitude and soil depth. At the vibration distance of 250 mm, the dominant frequency is approximately twice the vibration frequency at 7–11 Hz and approximately equal to the vibration frequency at 13–15 Hz. Multiple exponential functions were used to fit the peak pressure attenuation function, obtaining an effective transmission distance range of 347.15 to 550.37 mm for the 5kPa cut-off pressure. For a soil depth of 300 mm, the vertical shear wave diffusion angle is greater than the horizontal shear wave diffusion angle. The study clarifies the vibration response of soil under low-frequency vibration, which helps to design vibration type soil-engaging components of tillage machinery and match vibration parameters for energy saving and resistance reduction in soil tillage.

Estimating peak flow for a catchment is commonly undertaken using the design event method, however this method does not allow for the understanding of uncertainty in the result. This research first presents a simplified method of fragments approach to rainfall disaggregation that ignores the need to consider seasonality, offering a greater diversity in storm patterns within the resulting sub-daily rainfall. By simulating 20 iterations of the disaggregated sub-daily rainfall within a calibrated continuous simulation hydrologic model, we were able to produce multiple long series of stream flow at the outlet of the catchment. With this data, we investigated the use of both the annual maximum and peaks over threshold approaches to flood frequency analysis and found that for a one in 100 year annual exceedance probability peak flow, the peaks over threshold method (333m3/s ±50m3/s) was significantly less uncertain than the annual maximum method (427m3/s ±100m3/s). For the one in 100 year annual exceedance probability, the median peak flow from the peaks over threshold method (333m3/s) produced an outcome comparable to the design event method peak flow (328m3/s), indicating that this research offers an alternative approach to estimating peak flow, with the additional benefit of understanding the uncertainty in the estimation. Finally, the paper highlighted the impact that length and period of streamflow has on peak flow estimation and noted that previous assumptions around the minimum length of gauged streamflow required for flood frequency analysis may not be appropriate in particular catchments.

Vitamin K is a multifunctional micronutrient essential for human health, and deficiency has been linked to multiple pathological conditions. In this study we aimed to develop and validate a new food frequency questionnaire (FFQ) to estimate total vitamin K intake, over the course of a 30-day interval, in a Portuguese, Mediterranean-based, population. We conducted a prospective study in a non-random sample of 38 healthy adult volunteers. The FFQ was designed based on a validated Portuguese FFQ used in nationally representative studies and on literature reviews, to include foods containing ≥ 5μg of vitamin K/100g and foods with a lower vitamin K content, yet commonly in-cluded in a Mediterranean diet. Vitamin K intake was estimated from 24h recalls and six days of food records. The final FFQ included 54 food items which, according to regression analyses, explains 90% of vitamin K intake. Mean differences in vitamin K intake based on food records (80±47.7 μg/day) and on FFQ (96.5±64.3 μg/day) were statistically non-significant. Further, we found a strong correlation between both methods (r= 0.7; p=0.003). Our results suggest that our new FFQ is a valid instrument to assess the last 30-days of vitamin K intake in the Portuguese Mediterranean population.

With the rapid development of electronic and communication technology in military radar, the demand for microwave absorbing materials in low-frequency with thin layer is growing increasingly. In this study, flexible Co3O4/CC (carbon cloth) composites derives from Co-MOFs (metal-organic frameworks)/CC are prepared by hydrothermal and thermal treatment processes. The flexible precursors of Co-MOFs/CC are calcined with different calcination temperatures, which the material structure, dielectric properties and microwave absorption performance are changed. With the increase of calcination temperature, the minimum reflection loss of the corresponding Co3O4/CC composites gradually moves to the lower frequency with thinner thickness. In addition, the Co3O4/CC composites with 25 wt% filler loading ratio exhibit the minimum reflection loss (RL) of -46.59 dB at 6.24 GHz with 4.2 mm thickness. When the thickness is 3.70 mm, the effective absorption bandwidth is 3.04 GHz from 5.84 to 8.88 GHz. This study not only proves that the composite Co3O4/CC is a kind of outstanding microwave absorbing material with better flexibility, but also provides a useful inspiration for the low frequency and broadband microwave absorbing material.

Graphene quality for use in biosensors was assessed in fabricated chips by a set of methods that includes atomic force microscopy (AFM), Raman spectroscopy, and low-frequency noise. It is shown that local areas of residues on the graphene surface, which arisen due to the interaction of graphene with a photoresist at the initial stage of chips development, leads to a spread of chips resistance (R) within 1-10 kΩ and to an increase in the root mean square (RMS) roughness up to 10 times that can significantly impair reproducibility of graphene parameters in biosensors chips. It was observed that the control of the photoresist residues after photolithography (PLG) by AFM and subsequent additional cleaning allow reducing the spread of R values in chips to 1–1.6 kΩ and obtaining RMS roughness similar to the roughness in pristine graphene before PLG. Monitoring of the spectral density of low-frequency voltage fluctuation (SU), which provides integral information about the defect system and quality of the material, makes it possible to identify chips with low graphene quality and with inhomogeneously distributed compressive stresses areas by the type of frequency dependence SU (f).

The replacement of chloroquine with artemisinin-based combination therapies (ACTs) for over a decade has had varying impacts on the ability of malaria parasite to sustain its chloroquine resistance prowess in different malaria-endemic regions. We evaluated the frequency of Plasmodium falciparum chloroquine resistance transporter (PfCRT) mutations in an endemic area of southwest Nigeria 17 years after replacement of chloroquine with ACTs for malaria treatment. Genomic DNA was isolated from dried blood spot samples obtained from 129 patients (aged 1-35 years) with microscopically confirmed P. falciparum infection. PfCRT fragments covering codons 72-76, CVMNK (wildtype) and A220 were amplified and sequenced. Two mutant PfCRT haplotypes on residues 72-76 (CVIET and CVINT) were identified with a prevalence of 18.6% and 2.3%, respectively. Interestingly, the CVINT haplotype was identified for the first time in this region. A220S changes were found in 16.3% of samples occurring concurrently with the CVIET haplotype, while a Q271E mutation occurred in a wildtype isolate. The reduced prevalence of the PfCRT mutant alleles in this study may suggest a gradual disappearance of chloroquine-resistant malaria parasites following reduced drug pressure. It may also be an indicator of the ability of malaria parasites to develop resistance gradually against the current first-line regimen.

The recent advances in Human-Computer Interaction and Artificial Intelligence have significantly increased the importance of identifying human emotions from different sensory cues. Hence, understanding the underlying relationships between emotions and sensory cues have become a subject of study in many fields including Acoustics, Psychology, Psychiatry, Neuroscience and Biochemistry. This work is a preliminary step towards investigating cues for human emotion on a fundamental level by aiming to establish relationships between tonal frequencies of sound and emotions. For that, an online perception test is conducted, in which participants are asked to rate the perceived emotions corresponding to each tone. The results show that a crossover point for four primary emotions lies in the frequency range of 417–440 Hz, thus consolidating the hypothesis that the frequency range of 432–440 Hz is neutral from human emotion perspective. It is also observed that the frequency dependant relationships between emotion pairs Happy—Sad, and Anger—Calm are approximately mirrored symmetric in nature.

A comprehensive presentation of a variety of biologically sounding properties of genomes is present; chloroplast genomes are used as a biological matter. Triplet frequency composition is the general issue standing behind the properties. Besides, the new alignment-free error-tolerant method of sequences comparison highly efficient for in/del mismatches is present, for transposons search. Triplet frequency dictionaries determined for a genome, or for a part of that latter were studied through various clustering techniques. The interplay between triplet composition and function reveals on tRNA genes unambiguously shows the prevalence of the function encoded in tRNA gene over the phylogeny: the genes gather into the clusters comprising the genes encoding the same amino acid; more exactly, few gene families exhibit fine cluster pattern corresponding the synonymous codons of amino acid. Previously reported symmetry in chloroplast genomes is shown for a set of gymnosperm: that is mirror symmetry, rotational symmetry, and the second Chargaff's parity rule asymmetry. A family of transposons was found in gymnosperm chloroplast genomes. This family is revealed through the novel comparison method based on convolution calculation, for a set of DNA sequences.

The increase in the number of firms manipulating financial reports has misled shareholders' investment decisions and resulted in an indelible blot on foreign investors’ trust. Due to earnings management (EM) practice, managers' inefficiency, and lack of transparency in Iraq companies. This study tested the influence of the corporate governance mechanisms (CG), (board independence, audit committee, meeting frequency) on EM based on agency theory, as well, to link between EM and firm's performance (FP) in Iraqi listed companies and the impact of moderating role of corporate social responsibility (CSR) based on the Stakeholder Theory. The study's sample consists of 65 companies for the 2013-2018 financial years. Data were collected mainly from the annual reports (secondary data) of the Iraqi listed firms. This study uses the M-score model to detect EM practices as practical techniques in detecting earnings manipulation practices. The panel static model estimators. Hence, this paper adds to the CG literature from the perspective of stakeholder theory using Iraq's unique industrial environment. Based on the research results, policy-makers might use the study‘s findings to recognize the essential roles of several CG mechanisms in alleviating the opportunistic practices in Iraq. Further, companies should also be encouraged to enhance the CSR disclosure quality.

Focal vibration therapy can provide neurophysiological benefits. Unfortunately, standardized protocols are non-existent. Previous research presents a wide range of protocols with a wide range of effectiveness. This paper is part of a broader effort to identify effective, standardized protocols for focal vibration therapy. The vibration characteristics of four commercially available focal vibration devices that have been used for research and clinically were measured. An accelerometer was used for the measurements. Frequency and peak-to-peak amplitude were measured. Measurements were made when the devices were free and then again when they were strapped to the human body. Vibration frequency ranged from 120 to 225 Hz. Free vibration amplitude ranged from 2.0 to 7.9 g’s (peak-to-peak). When the devices were strapped to the body (constrained), vibration amplitude decreased by up to 65.7%. These results identify effective ranges of focal vibration frequency and amplitude. They illustrate the importance of identifying vibration environment, free or constrained, when quoting vibration characteristics. Finally, the inconsistency of multi-actuator devices is discussed. These results will guide protocol development for focal vibration and potentially better focal vibration devices.

This paper presents the simplified and quick way to obtain an experimental measure of the modulus of elasticity(E) of a piece of metal rod using the Smartphone microphone and through the experimental configuration in mode of unsupport beam Euler-Bernoulli(E-B). To understand it, it is required to have knowledge about flexural vibration of E-B beams and to know the analysis of the spectogram of the audio signal. The methodology consists in measuring the flexural resonance frequency through an app installed on a Smartphone and using the E formula deduced from the E-B theoretical framework. The results of the experimental measurements have a discrepancy of less than 5% with respect to the factory value, for a carbon steel rod with circular cross section using the impact excitation technique. It describes the precision and accuracy of the experimental measurement. It is useful, because it helps to classify the materials in the Faculty of Engineering and it helps to make a more efficient quality control.

An 18.8–33.9-GHz, 2.26-mW current-reuse (CR) injection-locked frequency divider (ILFD) for radar sensor applications is presented in this paper. A fourth-order resonator is designed using a transformer with a distributed inductor for wideband operating of the ILFD. The CR core is employed to reduce the power consumption compared to conventional cross-coupled pair ILFDs. The targeted input center frequency is 24 GHz for radar application. The self-oscillated frequency of the proposed CR-ILFD is 14.08 GHz. The input frequency locking range is from 18.8 to 33.8 GHz (57%) at an injection power of 0 dBm without a capacitor bank or varactors. The proposed CR-ILFD consumes 2.26 mW of power from a 1-V supply voltage. The entire die size is 0.75 mm ´ 0.45 mm. This CR-ILFD is implemented in a 65-nm CMOS technology.

Due to the high solar irradiance or energy price, certain regions in the U.S. may reach 100% PV penetration and experience degradation of frequency response greater than the interconnection as a whole. Therefore, in this section, the 100% PV penetration region in each interconnection is simulated to study the local high PV penetration effects. The study was performed by quantifying RoCoF, frequency nadir, and settling frequency at different regional PV penetration levels. The impact of high regional PV penetration on the compliance of grid code on frequency response is also studied.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li.

In this manuscript we report new effects of resonance detuning on various dynamical parameters of a generic 3-wave system. Namely, for suitably chosen values of detuning the variation range of amplitudes can be significantly wider than for exact resonance. Moreover, the range of energy variation is not symmetric with respect to the sign of the detuning. Finally, the period of the energy oscillation exhibits non-monotonic dependency on the magnitude of detuning. These results have important theoretical implications where nonlinear resonance analysis is involved, such as geophysics, plasma physics, fluid dynamics. Numerous practical applications are envisageable e.g. in energy harvesting systems.

This study presents an exploration into identifying the interactions between ocean waves and the continental margin in the origination of double-frequency (DF, 0.1-0.5 Hz) microseisms recorded at 33 stations across East Coast of USA (ECUSA) during a ten-day period of ordinary ocean wave climate. Daily primary vibration directions are calculated in three frequency bands and projected as great circles passing through each station. In each band, the great circles from all stations exhibit largest spatial density primarily near the continental slope in the western North Atlantic Ocean. Generation mechanisms of three DF microseism events are explored by comparing temporal and spatial variations of the DF microseisms with the migration patterns of ocean wave fronts in Wavewatch III hindcasts. Correlation analyses are conducted by comparing the frequency compositions of and calculating the correlation coefficients between the DF microseisms and the ocean waves recorded at selected buoys. The observations and analyses lead to a hypothesis that the continental slope causes wave reflection, generating low frequency DF energy and that the continental shelf is where high frequency DF energy is mainly generated in ECUSA. The hypothesis is supported by the primary vibration directions being mainly perpendicular to the strike of the continental slope.

This study aims to assess the spatiotemporal characteristics of meteorological droughts in Bangladesh during 1981–2015 using the Effective Drought Index (EDI). Monthly precipitation data for 36 years (1980-2015) obtained from 27 metrological stations, were used in this study. The EDI performance was evaluated for four sub-regions over the country through comparisons with historical drought records identified at the regional scale. Analysis at a regional level showed that EDI could reasonably detect the drought years/events during the study period. The study also revealed that the overall drought severity had increased during the past 35 y; the most significant increasing trend was observed in the central region. The characteristics (severity and duration) of drought were also analysed in terms of spatiotemporal evolution of the frequency of drought events. It was found that the western and central regions of the country are comparatively more vulnerable to drought. Moreover, the southwestern region is more prone to extreme drought, whereas the central region is more prone to severe droughts. In addition, the central region was more prone to extra-long-term droughts, while the coastal areas in the southwestern as well as in the central and north-western region were more prone to long-term droughts. The frequency of droughts in all categories significantly increased during the last quinquennial period (2011 to 2015). The seasonal analysis showed that the north-western areas were prone to extreme droughts during the Kharif (wet) and Rabi (dry) seasons. The central and northern regions were affected by recurring severe droughts in all cropping seasons. Further, the most significant increasing trend of the drought-affected area was observed within the central region, especially during the pre-monsoon (March-May) season. The results of this study can aid policymakers in the development of drought mitigation strategies in the future.

Soil conditions is a major aspect of interest for farmers due to the knowing of the physicochemical properties of the same can help with any necessary restoration of soil that guarantees the quality and the production of their crop. However, technology and analysis of the soil become of difficult access mainly in developing countries, by which the present paper shows the development of a system thought to estimate physicochemical variables of soils growing sugar cane through studies of spectroscopy. Its characteristic is that it is a portable system, with low cost, easy to use and can estimate physicochemical variables in-situ with the objective of knowing the degree of degradation present in the soil and through this help the farmers define possible strategies to restore it. The device uses the frequency response of the soil determining values of magnitude and phase, which are used by algorithms of artificial intelligence capable of getting an estimation of the physicochemical properties. The obtained results show errors below 8% in the estimation of the variables compared to the analysis results of the soil at laboratories.

Crowd counting is of significant importance for numerous applications, e.g., urban security, intelligent surveillance and crowd management. Existing crowd counting methods typically require specialized hardware deployment and strict operating conditions, thereby hindering their widespread deployment. To acquire a more effective crowd counting approach, a device-free counting method based on Channel Status Information (CSI) is proposed, which could mitigate environment noise through wavelet transform and extract the amplitude or phase covariance matrix as the feature vector. Moreover, both the spatial diversity and frequency diversity are leveraged to improve detection robustness. The accuracy of the proposed CSI-based method is compared with a renowned crowd counting one, i.e., Electronic Frog Eye: Counting Crowd Using WiFi (FCC). The experimental results reveal an accuracy improvement of 30% over FCC.

Abstract: Objective: The aim of the study was to identify dietary patterns and its association with socio-economic, dietary and lifestyle practices among adolescents in Malaysia. Methods: A validated food frequency questionnaire was used to assess dietary patterns. Results: Multivariate analyses show that age and physical activity (PA) levels were emerged as positive determinants of healthy-based food pattern in Malay (All, p<0.001), whereas higher consumption of eating-out from home (EatOut) and fast food (All, p<0.05) were negative determinants. High weekly breakfast skipping (p<0.001) and EatOut (p<0.01) were positively associated with a western-based pattern, whereas age (p<0.001) and household income (p<0.05) were negative determinants. Higher frequency of daily snacking (p<0.05) was emerged as positive determinant of local-based food pattern. For Chinese adolescents, age (p<0.001), PA levels (p<0.001) and maternal education level (p<0.05) emerged as positive determinants for the healthy-based pattern, whereas high EatOut and fast food intakes (All, p<0.01) were negative determinants. Higher weekly consumption of EatOut (p<0.01), fast food (p<0.05) and carbonated beverages (p<0.05), and daily snacking practice (p<0.01) were positively associated with higher western-based food pattern, whereas age (p<0.01) was inversely associated. Conclusion: These findings suggest that unhealthy dietary and lifestyle practices could increase the risk of adherence to unhealthy western-based food pattern that is high in fat, sugar and salt contents, and consequently increase the risk of developing obesity and metabolic-related disorders during these critical years of growth.

The production of lithium-ion battery cells is characterized by a high degree of complexit due to numerous cause-effect relationships between process characteristics. Knowledge about the multi-stage production is spread among several experts, rendering tasks such as failure analysis challenging. In this paper, a method is presented, which includes expert knowledge acquisition in production ramp-up by combining Failure Mode and Effects Analysis (FMEA) with a Bayesian Network. We show the effectiveness of this holistic method by building up a large scale, cross-process Bayesian Failure Network in lithium-ion battery production. Using this model, we are able to conduct root cause analyses as well as analyses of failure propagation. The former support operators in identifying root causes once a cell possesses a specific failure by calculating most-probable explanations matched to the individual battery cell data. The latter enable us to analyze propagation of failures and deviations in the production chain and thus provide support for placement of quality gates, leading to a significant reduction in scrap rate. Moreover, it gives an insight into which process steps are key drivers for which final product characteristics.

Identifying macroeconomic events that are responsible for dramatic changes of economy is of particular relevance to understand the overall economic dynamics. We introduce an open-source available efficient Python implementation of a Bayesian multi-trend change point analysis which solves significant memory and computing time limitations to extract crisis information from a correlation metric. Therefore, we focus on the recently investigated S&P500 mean market correlation in a period of roughly 20 years that includes the dot-com bubble, the global financial crisis and the Euro crisis. The analysis is performed two-fold: first, in retrospect on the whole dataset and second, in an on-line adaptive manner in pre-crisis segments. The on-line sensitivity horizon is roughly determined to be 80 up to 100 trading days after a crisis onset. A detailed comparison to global economic events supports the interpretation of the mean market correlation as an informative macroeconomic measure by a rather good agreement of change point distributions and major crisis events. Furthermore, the results hint to the importance of the U.S. housing bubble as trigger of the global financial crisis, provide new evidence for the general reasoning of locally (meta)stable economic states and could work as a comparative impact rating of specific economic events.

The most extensive urban growths in the next 30 years are expected to occur in developing countries. Lagos, Nigeria - Africa’s second most populous megacity- is a prime example. To achieve more sustainable and resilient cities, there is a need for modeling the urban growth patterns of major cities and analyzing their implications. In this study, the urban growth of Lagos state was modeled using the Multi-Layer Perceptron (MLP) neural network for the transition modeling and the Markov Chain analysis for the change prediction, achieving a model accuracy of 81.8%. An innovative visual validation of the model results using the ArcGIS was combined with kappa correlation statistics. The results show that by 2031, built-up areas will be the most spatially extensive LULC class in the study area with percentage coverage of 34.1% as opposed to 9% in 1986. The coverage of bare areas is also expected to increase by 53% between 2016 and 2031. Conversely, 24.9% and 68.3% loss of forestlands and wetlands respectively, are expected between 2016 and 2031. In view of the 11^th goal of SDGs which focuses on achieving sustainable cities and communities, the objectives of African Union’s Agenda 2063, and based on the urban growth trends observed, the study recommends a prioritization of vertical expansion as opposed to the current horizontal urban growth trends in the study area.

Fragmentation processes of multiply charged ions of C10H8 isomers produced in fast proton collision (velocity between 1.41 and 2.4 a.u.) is discussed in view of their fundamental molecular dynamics. Especially so in the mechanisms to produce a variety of carbon clusters from such ions. This aspect is assessed with the help of a multihit analysis of daughter ions in coincidence with elimination of H+ and CHn+ (n = 0 to 3). The elimination of H+/C+ was found to be very different from CH3+ loss. The loss of CH3+ was found to be accompanied with the formation of heavy ions like C9H5+, C9H5++ and C7H3+ by a cascade of momentum correlated dissociations. The most probable structures of large fragment ions in the CH3+ loss cascade are predicted with the help of computed electronic energy and the multihit ToF correlations of second and third hit. In addition, we report observation of super-dehydrogenation of naphthalene and azulene targets, with evidence of complete dehydrogenation in a single collision.

This paper proposes a multi-terminal adaptive collaborative operation method to solve the problem of unstable internal force tracking in clamping and handling unknown objects by multi-terminal robots. In the proposed method, the internal command force changes the complex internal force control problem into an internal force tracking problem from multi-slave to master. Moreover, we develop an algorithm for multi-slave setups to estimate object stiffness and motion uncertainty in the direction of the internal command force according to Lyapunov theory. Finally, the impedance control generates a reference trajectory for the multi-slave to maintain the desired internal force and track the master’s motion. Several experiments are conducted on a self-made robot equipped. The experimental results show that the oscillation amplitude of each slave end is less than 1 mm, the directional oscillation amplitude is less than 1 degree during the tracking of the desired commanded internal force. For objects with low stiffness, the error of the commanded internal force is less than 1 N (6%) per slave. The error in tracking the commanded internal force for objects with high stiffness is less than 2 N (8%). The results prove the feasibility and effectiveness of the proposed method.

In gravitational theory and astrophysical dynamics, singular initial value problems (IVPs) are frequently encountered. Finding the solutions to this class of IVPs can be challenging due to their complex nature. This study strives to circumvent the complexity by proposing a numerical method for solving such problems. The approach proposed in the current research seeks solutions to the IVP by partitioning the domain [0,L] of the problem into two intervals and solving the problem on each domain. The study seeks a closed-form solution to the IVP in the interval containing the singular point. A linearization technique and piecewise partitioning of the domain not containing the singularity are applied to the nonlinear IVP. The resulting linearized differential equation is solved using the Chebyshev spectral collocation method. Some examples are presented to illustrate the efficiency of the proposed method. Numerical analysis of the solution and residual errors are shown to ascertain convergence and accuracy. The results suggest that the technique gives accurate convergent solutions using a few collocation points.

Dracunculiasis (also known as Guinea worm disease) is caused by Dracunculus medinensis parasite and it spreads by drinking water containing Larvae of Guinea worm. The lack of safe water facilities, preventions and treatments resulted in highly dangerous consequences in its endemic regions. The economy of the affected regions totally falls down due to less production which is the result of agricultural field worker’s bad health. In this study, a multi epitope vaccine was designed against Dracunculus medinensis by using immune-informatics. The vaccine was designed by using T-Cell and B-Cell epitopes derived from Dracunculus medinensis proteins (Lactamase-B domain-containing protein, G-Domain containing protein and Ferrochelatase) in addition to Adjuvants and Linkers. The tertiary structure, physiochemical properties and immunogenic elements of vaccine were achieved. The validation of tertiary structure was accessed, and quality was achieved. In addition, the world coverage of parasite’s CTL and HTL epitopes is 95.61%. The stability of the chimeric vaccine was achieved through disulfide engineering. The molecular docking with Toll Like Receptor 4 (TLR-4) of vaccine showed its binding efficiency followed by Molecular Dynamic Simulation. The immune simulation suggested the mediated cell immunity and repeated antigen clearance. At the end, the optimized codon was used in in silico cloning to ensure vaccine’s higher exposure in bacterium E. coli strain K12. With further assessments, it is believed that the proposed multi epitope vaccine has strong immunogen to control Dracunculus medinensis which may result in better social and economic conditions of endemic regions.

Introduction Tuberculosis is common in Pakistan. Due to various factors including socioeconomic factors, compliance is poor to anti-tuberculosis drugs, leading to resistance. We aim to determine the prevalence of Multidrug resistance (MDR) tuberculosis in Pakistani population.Methods A prospective observational study was conducted from April 1, 2019, to December 31, 2019, in the Pulmonology department of a tertiary care hospital in Pakistan. Culture and sensitivity were assessed using a sputum sample or, in cases of an absent sputum sample, from Broncho alveolar lavage.ResultsApproximately 71.3% percent patients who had tuberculosis were found to be resistant to Isoniazid and around 48.6% did not respond to Rifampin. Multi-drug resistant was found in 29.4% participants.ConclusionMulti-drug resistance tuberculosis is very prevalent in Pakistan, which may increase burden on health care system and may lead to various complications of tuberculosis.