Background: A significant proportion of SARS-CoV-2-infected patients develops respiratory failure. Thromboembolism is also prevalent in coronavirus disease 2019 (Covid-19). Vitamin K plays a role in coagulation and possibly also in lung diseases. We therefore hypothesized that vitamin K is implicated in Covid-19 pathogenesis. Methods: 134 Covid-19 patients and 184 controls were included. Inactive vitamin K-dependent matrix Gla protein (i.e.dp-ucMGP) and prothrombin (i.e. PIVKA-II) were measured, which are inversely related to respectively extrahepatic and hepatic vitamin K status. Desmosine was measured to quantify elastic fiber degradation. Lung involvement and arterial calcifications severity were assessed by computed tomography. Results Dp-ucMGP was elevated in Covid-19 patients compared to controls (P=0.001). Higher dp-ucMGP was found in Covid-19 patients with poor compared to better outcomes (P=0.002). PIVKA-II was normal in 81.8%, mildly elevated in 14.0% and moderately elevated in 4.1% of Covid-19 patients not using vitamin K antagonists. Dp-ucMGP in Covid-19 patients was correlated with desmosine (P<0.001), thoracic aortic calcification (P<0.001) but not with pneumonia severity. Conclusions: Extrahepatic vitamin K status was severely reduced in Covid-19 patients, as reflected by elevated inactive MGP, and related to poor outcome. Procoagulant prothrombin activity remained preserved in the majority of Covid-19 patients, which is compatible with the increased thrombogenicity that is frequently observed in severe Covid-19. Impaired MGP activation was linked to accelerated elastic fiber degradation and premorbid vascular calcifications. A trial should assess whether increasing MGP and protein S activity by vitamin K administration improves Covid-19 outcomes.

Background: Since the previous study dealing with the case fatality ratio and infection fatality ratio caused by COVID-19, the author has received many comments that prompted the question: "Why did an optimistic prognosis fail?" To answer this question, a more detailed and expanded analysis was carried out in a new study. Objective: To evaluate the dynamics of monthly numbers of cases, deaths, tests and CFR worldwide during three phases of the COVID-19 pandemic. Material and Methods: Twenty three sets of databases, dated the 22nd of each month from January 2020 to November 2021, for 213 countries were collected from the Worldometer website. The number of cases, deaths, tests, CFR, IFR, etc. were counted for various periods of time for each of the 213 countries, then results related to different periods of time were compared. Results: The analysis of the main epidemiological parameters led to the division of three phases of the global pandemic evolution. The first phase (23.01.20-22.07.20), the second phase (23.07.20-22.01.21) and the third phase (23.01.21-22.07.21) were different in terms of the number of tests performed, new cases, and mortality due to COVID-19. By the end of the second phase, the worldwide statistics indicated the imminent end of the pandemic, but the third phase was characterized by a sudden rise in the number of new cases and deaths that could not be explained rationally. The most dramatic evolution of the epidemic curve occurred in the countries where doctors had successfully battled COVID-19 during the first two phases of the pandemic. Conclusions: Despite the decrease in overall death numbers during the latest months analyzed, additional study is necessary to identify the cause for the increase in the number of new cases and deaths during the third phase of the pandemic. Only complete information regarding the positive and negative impact of medical and non-medical methods of diagnostics and prophylaxis of COVID-19 can help to organize effective measures to end the current pandemic and prevent a similar one from occurring in the future. Presumably, there are several causes of the negative evolution of the current pandemic, including the overreliance on PCR tests, application of non-specialized premises for quarantine and treatment, decrease in herd and individual immunity, inadequate change of therapeutic protocols, and ignoring prophylactic treatment. It can be suggested that the use of immunemodulatory drugs, for example, thymus extract or thymic peptides, in groups of people with compromised immunity is necessary, and prophylactic and therapeutic protocols should be changed from the 'standard' types to 'personalized' ones.

The highest efficiency solar cell won in the efficiency race does not always give the most excellent annual energy yield in the real world solar condition that the spectrum is ever-changing. The study of the radiative coupling of the concentrator solar cells implied that the efficiency could increase by the recycle of the radiative recombination generated by the surplus current in upper junction. Such configuration is called by a super-multi-junction cell. We expanded the model in the concentrator solar cell to non-concentrating installation. It was shown that this super-multi-junction cell configuration was found robust and can keep the maximum potential efficiency (50 % in realistic spectrum fluctuation) up to 10 junctions. The super-multi-junction cell is also robust in the bandgap engineering of each junction. Therefore, the future multi-junction may not be needed to tune the bandgap for matching the standard solar spectrum, as well as relying upon artificial technologies like ELO (Epitaxial lift-off), wafer-bonding, mechanical-stacking, and reverse-growth, but merely uses up-right and lattice-matching growth technologies. We have two challenging techniques; one is the optical cap layer that may be the directional photon coupling layer in the application of the photonics technologies, and another is the high-quality epitaxial growth with almost 100 % of the radiative efficiency.

This study was aimed to investigate the effect of capital structure on firms’ profitability with special emphasis on Ethiopian Large Private Manufacturing Firms using panel data of five consecutive years (2006/07-2010/11G.C). The secondary data sources (audited financial statements) have been collected from the randomly selected thirty three large private manufacturing firms in Ethiopia. Linear regression model has been employed to analyze the relationship between firms’ profitability and capital structure. Specifically, Random-effect Generalized Least Square of panel data regression model has been selected to empirically test the literature driven hypotheses. Finally, the findings of this study revealed that a significant positive relationship between firms’ profitability and total debt ratio which indicate firm’s capital structure.

Following legalization, cannabis has quickly become an important horticultural crop in Canada and increasingly so in other parts of the world. However, due to previous legal restrictions on cannabis research there are limited scientific data on the relationship between nitrogen (N), phosphorus (P), and potassium (K) supply (collectively: NPK) and the crop yield and quality. This study examined the response of a high delta-9-tetrahydrocannabinol (THC) Cannabis sativa cultivar grown in deep-water culture with different nutrient solution treatments varying in their concentrations (mg L^-1) of N (70, 120, 180, 250, 290), P (20, 40, 60, 80, 100) and K (60, 120, 200, 280, 340) according to a central composite design. Results demonstrated that inflorescence yield responded quadratically to N and P, with the optimal concentrations predicted to be 194 and 59 mg L^-1, respectively. Inflorescence yield did not respond to K in the tested range. These results can provide guidance to cultivators when formulating nutrient solutions for soilless cannabis production and demonstrates the utility of surface response design for efficient multi-nutrient optimization.

In the paper, the authors generalize the notion "k-Mittag-Leffler function'', establish some integral transforms of the generalized k-Mittag-Leffler function, and derive several special and known conclusions in terms of the generalized Wright function and the generalized k-Wright function.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

In the paper, the author presents explicit and unified expressions for a sequence of improper integrals in terms of the beta functions and the Wallis ratios. Hereafter, the author derives integral representations for the Catalan numbers originating from combinatorics.

Build a special identical equation, use its calculation characters to prove and search for solution of any odd converging to 1 equation through (*3+1)/2^k operation, change the operation to (*3+2^m-1)/2^k, and get a solution for this equation, give a specific example to verify. Thus prove the Collatz Conjecture is true. Furthermore, analysis the sequences produced by iteration calculation during the procedure of searching for solution, build a weight function model, prove it decrease progressively to 0, build a complement weight function model, prove it increase to its convergence state. Build a (*3+2^m-1)/2^k odd tree, prove if odd in (*3+2^m-1)/2^k long huge odd sequence can not converge, the sequence must outstep the boundary of the tree after infinite steps of (*3+2^m-1)/2^k operation.

Identifying the SARS-CoV-2 virus has been a unique challenge for the scientific community. In this paper, we discuss a practical solution to help guide clinicians with interpretation of the probability that a positive, or negative, COVID-19 test result indicates an infected person, based on their clinical estimate of pre-test probability of infection.The authors conducted a small survey on LinkedIn to confirm that hypothesis that that the clinical pre-test probability of COVID-19 increases relative to local prevalence of disease plus patient age, known contact, and severity of symptoms. We examined results of PPA (Positive Percent Agreement, sensitivity) and NPA (Negative Percent Agreement, specificity) from 73 individual laboratory experiments for molecular tests for SARS-CoV-2 as reported to the FIND database ¹, and for selected methods in FDA EUA submissions^2,3. Authors calculated likelihood ratios to convert pre-test to post-test probability of disease and designed an online calculator to create graphics and text to report results. Despite best efforts, false positive and false negative Covid-19 test results are unavoidable^4,5. A positive or negative test result from one laboratory has a different probability for the presence of disease than the same result from another laboratory. Likelihood ratios and confidence intervals can convert the physician or other healthcare professional’s clinical estimate of pre-test probability to post-test probability of disease. Ranges of probabilities differ depending on proven method PPA and NPA in each laboratory. We recommend that laboratories verify PPA and NPA and utilize a the “Clinician’s Probability Calculator” to verify acceptable test performance and create reports to help guide clinicians with estimation of post-test probability of COVID-19.

Background: The COVID-19 transmission has been established to occur through respiratory droplets from coughing and sneezing. Health agencies have strongly recommended the use of facemask as a precaution from cross-transmission. Objective: This study investigated the prevalence of facemask use among visitors to the hospital. This study also investigated the demographic factors contributing to unacceptable facemask practice. Setting: This prospective observational study was done among hospital visitors to a district specialist hospital during COVID-19 pandemic outbreak. Methods: Individuals entering through dedicated entry point were observed for the type, category and practice of wearing personal protective equipment. Inclusion criteria for this study were any individual's ≥ 2 years old entering the treatment facility from selected entry points. Patients were categorized into two groups of acceptable and unacceptable facemask practice. The Pearson chi-square was used to test for differences in investigated variables in the univariate setting and Binary Logistic regression model was used in the multivariate setting. Main Outcome Measure: Prevalence, acceptance practice and odds ratio of unacceptance of facemask use. Results: Among 1652 individuals included in the final analysis, 1574 (96.9%) was observed wearing facemask with 1269 (72.0%) of individuals worn medical-grade facemask. However, among them, only 1397 (88.8%) individuals' facemask practice was acceptable while the reaming 177 (11.2) individuals were perceived with unacceptable facemask practice. Male individuals, Malay ethnic and high risk age group are 1.47 times (Odds Ratio: OR=1.47; 95% CI, 1.06-2.06; p=.023), 2.18 times (OR=2.18; 95% CI, 1.55-3.08; p<.001) and 1.99 times (OR=2.18; 95% CI, 1.42 - 2.77; p<.001) more likely to exhibit unacceptable facemask practice respectively. Conclusion: Extensive use of facemasks coupled with environmental hygiene measures is a public health strategy which can help to mitigate the COVID-19 epidemic impact. However, a targeted comprehensive strategy to improve compliance to proper facemask practice among the high-risk population is needed to achieve maximal protective benefit.

Predicting the outcome of a future game between two National Basketball Association (NBA) teams poses a challenging problem of interest to statistical scientists as well as the general public. In this article, we formalize the problem of predicting the game results as a classification problem and apply the principle of maximum entropy to construct NBA maximum entropy (NBAME) model that fits to discrete statistics for NBA games, and then predict the outcomes of NBA playoffs by the NBAME model. The best NBAME model is able to correctly predict the winning team 74.4 percent of the time as compared to some other machine learning algorithms which is correct 69.3 percent of the time.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

In this paper, some convexity properties and some inequalities for the (p,k)-analogue of the Gamma function, Г_p,k(x) are given. In particular, a (p,k)-analogue of the celebrated Bohr-Mollerup theorem is given. Furthermore, a (p,k)-analogue of the Riemann zeta function, ζ_p,k(x) is introduced and some associated inequalities are derived. The established results provide the (p,k)-generalizations of some known results concerning the classical Gamma function.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

In this paper, we establish some inequalities bounding the ratio Г_p,k(x)/Г_p,k(y), where Г_p,k(.) is the (p,k)-analogue of the Gamma function. Consequently, some previous results are recovered from the obtained results.

The ratio of males to females with ASD is generally quoted as 4:1 though it is believed that there are biases preventing females being diagnosed and that the true ratio is lower. These biases have not been clearly identified or quantified. Starting with a clinical dataset of 1711 children <18 years old four different methods were employed in an inductive study to identify and quantify the biases and calculate the proportion of females missed. A mathematical model was constructed to compare the findings with current published data. The true male to female ratio appears to be 3:4. Eighty per cent of females remain undiagnosed at age 18 which has serious consequences for the mental health of young women.

Some studies have demonstrated that in vivo degradation processes are influenced by the material’s physico-chemical properties. The present study compares two hydroxyapatites manufactured on an industrial scale, deproteinized at low and high temperatures, and how physico-chemical properties can influence the mineral degradation process of material performance in bone biopsies retrieved 6 months after maxillary sinus augmentation. Residual biomaterial particles were examined by field scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) to determine the composition and degree of degradation of the bone graft substitute material. According to the EDX analysis, the Ca/P ratio significantly lowered in the residual biomaterial (1.08±0.32) compared to the initial composition (2.22±0.08) for the low-temperature sintered group, which also presented high porosity, low crystallinity, low density, a large surface area, and poor stability and a high resorption rate compared to the high-temperature sintered material. This demonstrates that variations in the physico-chemical properties of bone substitute material clearly influence the degradation process. Further studies are needed to determine whether the resorption of deproteinized bone particles proceeds slowly enough to allow sufficient time for bone maturation to occur.

Molecularly imprinted polymers (MIPs) were synthesized and applied for the selective extraction of oblongifolin C (OC) from fruit extracts of Garcinia yunnanensis Hu. A series of experiments and computational approaches were employed to improve the efficiency of screening for optimal MIP systems in the study. The molar ratio (1:4) was chosen at last based on the comparison of the binding energy of the complexes between the template (OC) and functional monomers using density functional theory (DFT) at the RI-PBE-D3-gCP/def2-TZVP level of theory. The binding characterization and the molecular recognition mechanism of MIPs were further explained using the molecular modeling method and NMR and IR spectra data. The reusability of this approach was demonstrated in over 20 batch rebinding experiments. 140.5 mg of OC (>95% purity) was obtained from the 5 g extracts with 2 g of MIPs with the best binding properties through gradient elution program from 35% to 70% methanol-water solution. At the same time, another structural analog, 46.5 mg of guttiferone K (GK) (>88% purity), was also obtained by the gradient elution procedure. Our results showed that the structural analogs could be separated from the crude extracts by the molecularly imprinted solid-phase extraction (MISPE) using a gradient elution procedure for the first time.

In recent experimental studies, we reported the aggravating effects of Asian sand dust (ASD) on male reproductive function in mice. However, the effects of fetal ASD exposure on male reproductive function have not been investigated. The present study investigated the effects of fetal ASD exposure on reproductive function in male offspring. Using pregnant CD-1 mice, ASD was administered intratracheally on days 7 and 14 of gestation, and the reproductive function of male offspring was determined at 5, 10, and 15 weeks after birth. The secondary sex ratio was significantly lower in the fetal ASD-exposed mice than in the controls. Histologic examination showed partial vacuolation of seminiferous tubules in immature mice. Moreover, daily sperm production (DSP) was significantly less in the fetal ASD-exposed mice than in the controls. DSP in the fetal ASD-exposed mice was approximately 10% less than the controls at both 5 and 10 weeks. However, both the histologic changes and the DSP decrease were reversed as the mice matured. These findings suggest that ASD exposure affects both the fetal development and the reproductive function of male offspring. In the future, it will be necessary to clarify the onset mechanisms of ASD-induced male fetus death and male reproductive disorders.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

Many clinical research datasets have a large percentage of missing values that directly impacts their usefulness in yielding high accuracy classifiers when used for training in supervised machine learning. While missing value imputation methods have been shown to work well with smaller percentages of missing values, their ability to impute sparse clinical research data can be problem specific. We previously attempted to learn quantitative guidelines for ordering cardiac magnetic resonance imaging during the evaluation for pediatric cardiomyopathy, but missing data significantly reduced our usable sample size. In this work, we sought to determine if increasing the usable sample size through imputation would allow us to learn better guidelines. We first review several machine learning methods for estimating missing data. Then, we apply four popular methods (mean imputation, decision tree, k-nearest neighbors, and self-organizing maps) to a clinical research dataset of pediatric patients undergoing evaluation for cardiomyopathy. Using Bayesian Rule Learning (BRL) to learn ruleset models, we compared the performance of imputation-augmented models versus unaugmented models. We found that all four imputation-augmented models performed similarly to unaugmented models. While imputation did not improve performance, it did provide evidence for the robustness of our learned models.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

This paper presents the results of an experimental investigation about target detecting with passive sonar in Persian Gulf. Detecting propagated sounds in the water is one of the basic challenges of the researchers in sonar field. This challenge will be complex in shallow water (like Persian Gulf) and noise less vessels. Generally, in passive sonar the targets are detected by sonar equation (with constant threshold) which increase the detection error in shallow water. Purpose of this study is proposed a new method for detecting targets in passive sonars using adaptive threshold. In this method, target signal (sound) is processed in time and frequency domain. For classifying, Bayesian classification is used and prior distribution is estimated by Maximum Likelihood algorithm. Finally, target was detected by combining the detection points in both domains using LMS adaptive filter. Results of this paper has showed that proposed method has improved true detection rate about 27% compare other the best detection method.

The k-means is one of the most popular and widely used clustering algorithm, however, it is limited to only numeric data. The k-prototypes algorithm is one of the famous algorithms for dealing with both numeric and categorical data. However, there have been no studies to accelerate k-prototypes algorithm. In this paper, we propose a new fast k-prototypes algorithm that gives the same answer as original k-prototypes. The proposed algorithm avoids distance computations using partial distance computation. Our k-prototypes algorithm finds minimum distance without distance computations of all attributes between an object and a cluster center, which allows it to reduce time complexity. A partial distance computation uses a fact that a value of the maximum difference between two categorical attributes is 1 during distance computations. If data objects have m categorical attributes, maximum difference of categorical attributes between an object and a cluster center is m. Our algorithm first computes distance with only numeric attributes. If a difference of the minimum distance and the second smallest with numeric attributes is higher than m, we can find minimum distance between an object and a cluster center without distance computations of categorical attributes. The experimental shows proposed k-prototypes algorithm improves computational performance than original k-prototypes algorithm in our dataset.

Upper Blue Nile basin (UBNB) is the water tower of Ethiopia and downstream countries. It contributes significant moistures to the surrounding atmosphere. However, the contribution of the moisture from the basin to the precipitation in the area is not well documented. Therefore, this paper is aimed at seasonal variation of upper Blue Nile basin moisture budget and the global moistures in the role of temporal and spatial precipitation variability. To this end, we used European Centre for Medium-range Weather Forecast (ECMWF) data from 1979-2017. The UBNB moisture contributed precipitation in the central parts of the study area during the summer season, while in spring; it contributed in southern part of the study area. Northwest part of the study area got precipitation from the basin moistures during autumn season. The recycling ratios for four seasons (summer, autumn, spring and winter) were 9.70%, 16.33%, 19.01%, and 35.30% respectively. The maximum amount of precipitation is extracted from the local moistures during winter season. The annual average value of recycling ratio was found 20.11%. Hence, we concluded that UBNB moisture budget had lesser contribution of precipitation over the study area. It rather contributed a significant precipitation to the neighboring countries such as Egypt and Sudan. Further studies on moisture budget are required to explain this phenomenon in the context of Ethiopia.

The geometry of Poincare disk itself is interpreted without any mapping to dierent spaces. Our approach might be one of the shortest and is intended for educational contribution.

Male obesity secondary hypogonadism (MOSH) impairs fertility, sexual function, bone mineralization, fat metabolism, cognitive function, deteriorates muscle mass and alters body composition. The aim of this pilot study was to evaluate the effect of dietary intervention and physical activity on the MOSH patient’s hormonal profile after a 10% weight loss compared to baseline. Fourteen male patients were enrolled. Hormonal, lipid, glycemic profiles and body composition were determined at baseline and after a 10% weight loss. Aging Male Symptoms Scale (AMS) and Yale Food Addiction Scale (YFAS) were administered to patients in order to investigate hypogonadal symptoms and food addiction. Compared to baseline, a significant increase of Total Testosterone (TT) (300.2 ± 79.5 ng/dl vs 408.3 ± 125.9, p = 0.002, 95% CI 26.8; 167.7) and a reduction of 17-Beta Estradiol level (48.3 ± 14.9 pg/mL vs 39.2 ± 15.2, p = 0.049, 95% CI 3.1; 0.0) were observed. Total Fat Mass (FM) percentage, android and gynoid fat mass percentage (39.2 ± 6.4% vs 36.2 ± 5.8%, p = 0.0001, 95% CI 22.5; 62.3; 51.5 ± 6.8% vs 47.6 ± 6.8%, p = 0.001, 95% CI 0.6; 1.8, vs 39.2 ± 6.2% vs 36.5 ± 6.3% p= 0.0001, 95% CI 0.9; 2.0 respectively) were significantly decreased after nutritional intervention. In addition, total Fat Free Mass (FFM) in kg was significantly reduced after 10% weight loss (62.3± 2.8 kg vs 60.3± 7.7 kg, p = 0.002, 95% CI 45.0; 93.0). Lifestyle changes, specifically dietotherapy and physical activity, induce positive effects on hypogonadism due to obesity.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

In the paper, by virtue of some properties for the Riemann zeta function, the author finds a double inequality for the ratio of two consecutive Bernoulli numbers with even indexes and analyzes the approximating accuracy of the double inequality.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

Aeroponics is a relatively new soilless culture technology, which may produce food in space limited cities or non-arable land with high water use efficiency. The shoot and root growth, root characteristics, mineral contents of two lettuce cultivars were measured in aeroponics, as compared with hydroponics and substrate culture. The results showed that aeroponics remarkably improved the root growth with a significant greater root biomass, root/shoot ratio, and several times higher total root length, root area and root volume. However, the greater root growth did not lead to a better shoot growth compared with hydroponics, due to the limited availability of nutrients and water. It can be concluded that aeroponics systems may be better for high value true root crops production. Further research is necessary to figure out the suitable pressure, droplet size, and misting interval in order to improve the continuously availability of nutrients and water in aeroponics, if it is used to grow crops like lettuce for harvesting above-ground parts.

Within an Internet of Multimedia Things, the risk of disclosing streamed video content, such as arising from video surveillance, is of heightened concern. This leads to the encryption of that content. To reduce the overhead and lack of flexibility arising from full encryption of the content, a good number of selective-encryption algorithms have been proposed in the last decade. Some of them have limitations, in terms of significant delay due to computational cost, or excess memory utilization, or, despite being energy efficient, do not provide a satisfactory level of confidentiality, due to their simplicity. To address such issues, this paper presents a lightweight selective encryption scheme, in which encoder syntax elements are encrypted with the innovative EXPer (EXtended Permutation with exclusive OR). The selected syntax elements are taken from the final stage of video encoding that is during entropy coding. As a diagnostic tool, the Encryption Space Ratio measures encoding complexity of the video relative to the level of encryption so as to judge the success of the encryption process, according to entropy coder. A detailed comparative analysis of EXPer with state-of-the-art algorithms confirms that the EXPer provides significant confidentiality with a small computational cost and negligible encryption bitrate overhead. Thus, the results demonstrate that the proposed security scheme is a suitable choice for constrained devices in an Internet of Multimedia Things environment.

Mints emit diverse scents that exert specific biological functions and are relevance for applications. The current work strives to develop electronic noses that can electronically discriminate the scents emitted by different species of Mint as alternative to conventional profiling by gas chromatography. Here, 12 different sensing materials including 4 different metal oxide nanoparticle dispersions (AZO, ZnO, SnO2, ITO), one Metal-Organic Frame as Cu(BPDC), and 7 different polymer films including PVA, PEDOT: PSS, PFO, SB, SW, SG, PB were used for functionalizing of QCM sensors. The purpose was to discriminate six economically relevant Mint species (Mentha x piperita, Mentha spicata, Mentha spicata ssp. crispa, Mentha longifolia, Agastache rugosa, and Nepeta cataria). The adsorption and desorption datasets obtained from each modified QCM sensor were processed by three different classification models including Principal Component Analy-sis (PCA), Linear Discriminant Analysis (LDA), and k-Nearest Neighbor Analysis (k-NN). This allowed discriminating the different Mints with classification accuracies of 97.2% (PCA), 100% (LDA), and 99.9% (k-NN), respectively. Prediction accuracies with a repeating test measurement reached up to 90.6% for LDA, and 85.6% for k-NN. These data demonstrate that this electronic nose can discriminate different Mint scents in a reliable and efficient manner.

Among all the active confinement techniques, the use of pre-tensioned stainless steel straps has recently gained much attention. The flexibility of the stainless steel straps allows us to bend and pass them through the thickness of the masonry, thus creating a three-dimensional strengthening system between the two opposite facings. The use of the same perforation for the passage of several straps closed in a loop generates a continuous strengthening system that prevents parts of the structure from falling and injuring the occupants during seismic events. However, the perforations can nullify the in-plane strengthening, as they act as cylindrical hinges and make the reinforcement system labile for certain strap arrangements. Diagonal compression tests on square masonry panels performed in the present study show that the straps improve neither strength nor ductility when running along the mortar head and bed joints, arranged in square meshes. Conversely, they improve both strength and ductility when the straps make angles of 45° with the mortar joints. Furthermore, the experimental results show that the straps exert an anisotropic effect that decreases the apparent in-plane Poisson ratio. They also provide new insights into the diagonal compression test and allow formulating a new proposal for the pseudo-ductility factor.

Our matter universe is made up of four components of dark energy (DE), dark matters (DMs), leptons and quarks which are created from the decay of the primary black hole through the inflation after big bang. In the three-dimensional quantized space model, the sum (DER) of the dark energy (DE) and radiations (R) is the flat photon space and there are 39 particles of 3 dark matters, 9 leptons and 27 quarks. Generally speaking, the mass ratio of the quarks with the 27 particles is smallest and the mass ratio of the DER photon space with the 1 massless photon is largest. Therefore, the mass ratios of DER, DMs, leptons and quarks are inversely proportional to the particle numbers of DER, DMs, leptons and quarks as the first assumption. This simple rule is called as the universe mass ratio golden rule in Fig. 12. This simple rule is successfully applied to the observed mass ratios of the Planck and WMAP missions. The best particle number combination (1, 3, 9, 27) of the four components (DER, DMs, Leptons, Quarks) to explain the Planck 2018 and WMAP results is the same as the particle number combination (1, 3, 9, 27) of the 3-dimensional quantized space model. The calculated mass ratios of DER, DMs, leptons and quarks are 67.5 %, 22.5 %, 7.5 % and 2.5 %, respectively. And the calculated mass ratios of neutrinos and ordinary matters are 5.0 % and 5.0 %, respectively. The mass ratios of the dark energy (68.47(23) %) and matters (31.53(23) %) obtained from the Planck 2018 results are consistent with the calculated mass ratios of the DER (67.5 %) and matters (32.5 %). The mass ratio of the dark energy (72.1(15) %) obtained from the WMAP 9 year results is explained as the summed mass ratio (72.5 %) of DER (67.5 %) and neutrinos (5.0 %). The universe evolution including the super-massive black holes (SMBHs) is shown in Fig. 4. The accelerated space expansion of our universe requires the addition of the new dark energy. If this new dark energy is added, the mass ratio of the dark energy is a little bit increased. The difference (0.97 %) between the observed value (68.47(23) %) and calculated value (67.5 %) is explained by adding the new dark energy in Figs. 2, 4, 7, 8, 9, 10 and 11. The corrected mass ratios of DER, DMs, leptons and quarks are 68.47 %, 21.8286 %, 7.2762 % and 2.4254 %, respectively. The corrected mass ratios of the neutrinos (called as cosmic background neutrinos) and ordinary matters (OMs) are 4.8508 % and 4.8508 %, respectively. These corrected mass ratios can explain the mass ratios obtained from the WMAP and Planck missions. In other words, the mass ratios calculated from the best particle number combination support the elementary particles, dark matters and dark energy (photon space) proposed by the three-dimensional quantized space model based on the 10-D Euclidean space.

The main objective of this paper is to introduce k-fractional derivative operator by using the definition of k-beta function. We establish some results related to the newly defined fractional operator such as Mellin transform and relations to k-hypergeometric and k-Appell's functions. Also, we investigate the k-fractional derivative of k-Mittag-Leffler and Wright hypergeometric functions.

The contamination on the insulators may increase its surface conductivity and, as a consequence, electrical discharges occur more frequently, which can lead to interruptions in the power supply. To maintain reliability in the electrical distribution power system, components that have lost their insulating properties must be replaced. Identifying the components that need maintenance, is a difficult task as there are several levels of contamination that are hardly noticed during inspections. To improve the quality of inspections, this paper proposes to use the k-nearest neighbours (k-NN) to classify the levels of insulator contamination, based on the image of insulators at various levels of contamination simulated in the laboratory. Using computer vision features such as mean, variance, asymmetry, kurtosis, energy, and entropy are used for training the k-NN. To assess the robustness of the proposed approach, statistical analysis and a comparative assessment with well-consolidated algorithms such as decision tree, ensemble subspace, and support vector machine models are presented. The k-NN showed results of up to 85.17 % accuracy using the k-fold cross-validation method, with an average accuracy higher than 82 % for multi-classification of the contamination of the insulators, being superior to the compared models.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

Abstract: This paper is focusing on the stabilisation of soil using jute fibre as soil stabilizer. Stabilisation is the process of modifying the properties of a soil to improve its engineering performance and used it for a variety of engineering works. This study examines the potential of soil stabilization with jute fibre when it is cut into roughly 30mm lengths as stabilizer. The varying percentages like 0.5%, 1%, 1.5 and 2% of pieces of jute fibre were used and mixed it with soil. The laboratory tests such as California Bearing Ratio (CBR) test, modified compaction tests and direct shear strength tests have been conducted to observe the change in engineering properties of soil. On the basis of the experiments performed, it can be concluded that the stabilization of soil using 30mm pieces of jute as stabilizer improves the strength characteristics of the soil so that it becomes usable as one of the reinforcing material for the construction of roadways, parking areas, site development projects, airports and many other situations where sub-soils are not suitable for construction.

Increased nutrient withdrawal by rapidly expanding intensive cropping systems, in combination with imbalanced fertilization, is leading to potassium (K) depletion from agricultural soils in Asia. There is an urgent need to better understand the soil K-supplying capacity and K-use efficiency of crops to address this issue. Maize is increasingly being grown in rice-based systems in South Asia, particularly in Bangladesh and North East India. The high nutrient extraction, especially K, however, causes concerns for the sustainability of maize production systems in the region. The present study was designed to estimate, through a plant-based method, the magnitude, and variation in K-supplying capacity of a range of soils from the maize-growing areas and the K-use efficiency of maize in Bangladesh. Eighteen diverse soils were collected from several upazillas (or sub-districts) under 11 agro-ecological zones to examine their K-supplying capacity from the soil reserves and from K fertilization (@ 100 mg K kg-1 soil) for successive seven maize crops grown up to V10-V12 in pots inside a net house. A validation field experiment was conducted with five levels of K (0, 40, 80, 120 and 160 kg ha-1) and two fertilizer recommendations based on “Nutrient Expert for Maize-NEM” and “Maize Crop Manager-MCM” decision support tools (DSSs) in 12 farmers’ fields in Rangpur, Rajshahi and Comilla districts in Bangladesh. Grain yield and yield attributes of maize responded significantly (P < 0.001) to K fertilizer, with grain yield increase from 18 to 79% over control in all locations. Total K uptake by plants not receiving K fertilizer, considered as potential K-supplying capacity of the soil in the pot experiment, followed the order: Modhukhali >Mithapukur >Rangpur Sadar >Dinajpur Sadar >Jhinaidah Sadar >Gangachara >Binerpota >Tarash >Gopalpur >Daudkandi >Paba >Modhupur >Nawabganj Sadar >Shibganj >Birganj >Godagari >Barura >Durgapur. Likewise in the validation field experiment, the K-supplying capacity of soils was 83.5, 60.5 and 57.2 kg ha-1 in Rangpur, Rajshahi, and Comilla, respectively. Further, the order of K-supplying capacity for three sites was similar to the results from pot study confirming the applicability of results to other soils and maize-growing areas in Bangladesh and similar soils and areas across South Asia. Based on the results from pot and field experiments, we conclude that the site-specific K management using the fertilizer DSSs can be the better and more efficient K management strategy for maize.

All empirical water column correction methods have consistently been reported to require existing depth sounding data for the purpose of calibrating a simple depth retrieval model; they yield poor results over very bright or very dark bottoms. In contrast, we set out to (i) use only the relative radiance data in the image along with published data, and several new assumptions, (ii) in order to specify and operate the simplified radiative transfer equation (RTE), (iii) for the purpose of retrieving both the satellite derived bathymetry (SDB) and the water column corrected spectral reflectance over shallow seabeds. Sea truth regressions show that SDB depths retrieved by the method only need tide correction. Therefore it shall be demonstrated that, under such new assumptions, there is no need (i) for formal atmospheric correction, (ii) nor for conversion of relative radiance into calibrated reflectance , (iii) nor for existing depth sounding data, to specify the simplified RTE and produce both SDB and spectral water column corrected radiance ready for bottom typing. Moreover, the use of the panchromatic band for that purpose is introduced. Altogether, we named this process the Self-Calibrated Supervised Spectral Shallow-sea Modeler (4SM). This approach requires a trained practitioner, though, to produce its results within hours of downloading the raw image. The ideal raw image should be a “near-nadir” view, exhibit homogeneous atmosphere and water column, include some coverage of optically deep waters and bare land, and lend itself to quality removal of haze, atmospheric adjacency effect, and sun/sky glint.

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

A quantum hybrid (QH) intelligent approach that blends the adaptive search capability of the quantum-behaved particle swarm optimisation (QPSO) method with the intuitionistic rationality of traditional fuzzy k-nearest neighbours (Fuzzy k-NN) algorithm (known simply as the Q-Fuzzy approach) is proposed for efficient feature selection and classification of cells in cervical smeared (CS) images. From an initial multitude of seventeen (17) features describing the geometry, colour, and texture of the CS images, the QPSO stage of our proposed technique is used to select the best subset features (i.e. global best particles) that represent a pruned down collection of seven (7) features. Using a dataset of almost 1000 images, performance evaluation of our proposed Q-Fuzzy approach assesses the impact of our feature selection on classification accuracy by way of three experimental scenarios that are compared alongside two other approaches: The All-features (i.e. classification without prior feature selection) and another hybrid technique combining the standard PSO algorithm with the Fuzzy k-NN technique (P-Fuzzy approach). In the first and second scenarios, we further divided the assessment criteria in terms of classification accuracy based on the choice of best features and those in terms of the different categories of the cervical cells. In the third scenario, we introduced new QH hybrid techniques, i.e. QPSO combined with other supervised learning methods, and compared the classification accuracy alongside our proposed Q-Fuzzy approach. Furthermore, we employed statistical approaches to establish qualitative agreement with regards to the feature selection in scenarios 1 and 3. The synergy between the QPSO and Fuzzy k-NN in the proposed Q-Fuzzy approach marginally improves classification accuracy as manifest in the reduction in number cell features, which is crucial for effective cervical cancer detection and diagnosis.

Based on K-ε Standard Wall turbulence model (2-Equation) and Navier-Stokes (N-S) equations defined for incompressible fluids, fluid flow behaviour around hyperloop pods in an evacuated tube was simulated using ANSYS fluent solver assuming steady state and two dimensional conditions. In this research, to develop the case studies, using combination of different head and tail shape profile, four kind of hyperloop pods were developed with the aid of SolidWorks. These four pods have been investigated for their aerodynamic behaviour as four different case scenarios. The results of simulation depicts that an atmospheric pressure of 100 Pa with blockage ratio of 0.36 in tube provides the best possible aerodynamic behaviour for the designed hyperloop pod models. This research finds that overall aerodynamic behaviour of hyperloop pods can be varied by changing the head and tail shape profile of pods and a particular combination of head and tail shape profile can provide optimally best aerodynamic capabilities. Thus, this research paper provides a novel method of obtaining best aerodynamic capabilities in hyperloop pods by designing head profile optimally in combination with tail profile. This outcome will provide major contribution towards the development of hyperloop pods in future with better aerodynamic behaviour resulting in lesser electrical energy required to propel the hyperloop pods in evacuated tube.

Malaria is endemic in Nigeria and remains a major public health problem, taking its greatest toll on children under age 5 and pregnant women, although it is preventable, treatable, and curable. This study investigates the Impact of socio-economic factors and indoor mosquito control on malaria prevalent among pregnant women in Nigeria using logistic regression. To achieve this, secondary data obtained from 2015 Nigeria Malaria Indicator survey, executed by the National Malaria Elimination Programme (NMEP) and the National Population Commission (NPopC), with a nationally representative sample of more than 8,000 consisting of 7,745 households. The results from the logistic regression with odds ratio revealed that pregnant women are more like to be affected by malaria fever (though not significant) compared to women that are not pregnant. The income levels of the household does not significant reduce the incidence of malaria fever among pregnant women in Niger. Concerning the malaria presenting measure, only dwelling sprayed by private company significantly reduce the incidence of malaria fever among pregnant women (P-value=0.020<0.05) compared to dwelling sprayed by government and NGOs and also to Insecticide Treated Net. Also pregnant women in the urban centers are less likely to have malaria fever compared to pregnant women in rural communities in Nigeria. Also, pregnant women with atleast a secondary school level of education are less likely to be affected by malaria fever compared to pregnant women with no formal education. The fitted logistic model passed the goodness-of-test fit; the classification test for the logistic model was correctly classified at about 67.02%. Therefore, this study recommends that government and NGOs should intensify their efforts in the area of dwelling spraying, awareness campaign of the danger of malaria fever among pregnant women and infants, engaged in effective distribution of insecticide treated net in order to reduce the incidence of malaria fever among pregnant women living in rural communities in Nigeria.

The water-rich liquid layer immobilized on the surface of the polar stationary phases is critical to the retention of polar compounds in hydrophilic interaction chromatography (HILIC). Although the presence of the adsorbed water layer has been investigated and confirmed by multiple techniques, there is a lack of quantitative measure that can be easily determined and linked to chromatographic parameters. This study proposes a simple measure termed volume ratio (the ratio of the adsorbed water layer volume and the mobile phase volume) that provides a relative, but quantitative information on the adsorbed water layer and may be linked to the phase ratio. The volume ratio can be easily determined using toluene elution volume. The volume ratio values are measured in 25 polar stationary phases in various mobile phase conditions. In addition to the acetonitrile content in the mobile phase, ammonium acetate concentration in the mobile phase and column temperature also have significant influences on the volume ratio and the adsorbed water layer.

In this present paper, we deal with the generalized (k, s)-fractional integral and differential operators recently defined by Nisar et al. and obtain some generalized (k, s)-fractional integral and differential formulas involving the class of a function as its kernels. Also, we investigate a certain number of their consequences containing the said function in their kernels.

This paper presents an effective heart disease prediction model through detecting the anomalies, also known as outliers, in healthcare data using the unsupervised K-means clustering algorithm. Most existing approaches for detecting anomalies are based on constructing profiles of normal instances. However, such techniques require an adequate number of normal profiles to justify those models. Our proposed model first evaluates an \textit{optimal} value of K using Silhouette method. Next, it intends to locate anomalies that are far from a certain threshold distance with respect to their clusters. Finally, the five most popular classification techniques such as K-Nearest Neighbor (KNN), Random Forest (RF), Support Vector Machines (SVM), Naive Bayes (NB), and Logistic Regression (LR) are applied to build the resultant prediction model. The effectiveness of the proposed methodology is justified using a benchmark dataset of heart disease.

Noise reduction in medical images is a perplexing undertaking for the researchers in digital image processing. Noise generates maximum critical disturbances as well as touches the medical images quality, ultrasound images in the field of biomedical imaging. The image is normally considered as gathering of data and existence of noises degradation the image quality. It ought to be vital to reestablish the original image noises for accomplishing maximum data from images. Medical images are debased through noise through its transmission and procurement. Image with noise reduce the image contrast and resolution, thereby decreasing the diagnostic values of the medical image. This paper mainly focuses on Gaussian noise, Pepper noise, Uniform noise, Salt and Speckle noise. Different filtering techniques can be adapted for noise declining to improve the visual quality as well as reorganization of images. Here four types of noises have been undertaken and applied on medical images. Besides numerous filtering methods like Gaussian, median, mean and Weiner applied for noise reduction as well as estimate the performance of filter through the parameters like mean square error (MSE), peak signal to noise ratio (PSNR), Average difference value (AD) and Maximum difference value (MD) to diminish the noises without corrupting the medical image data.

While lidar-based forest inventory methods have been widely demonstrated, prediction of tree diameters with lidar is not well understood. The performance metrics typically used in studies for prediction of diameters can be difficult to interpret and may not support comparative inferences between sampling designs or study areas. We evaluate a variety of lidar and k nearest neighbor (k-NN) strategies for prediction of tree diameter distributions using two indices which are easier to interpret and compare. The indices are based on the coefficient of determination (R²), and root mean square deviation (RMSD). These indices facilitate comparisons with alternative (non-lidar) inventory strategies, and with other project areas. We evaluate k nearest neighbors (k-NN) dbh density (relative frequency by dbh class) prediction strategies with lidar for 190 training plots distribute across the 800 km² Savannah River Site in South Carolina, USA. We evaluate the performance of k-NN with respect to distance metrics, number of neighbors, predictor sets, and response sets. Amongst the examined strategies we found Mahalanobis distance with k = 3 neighbors performed best according to a number of criteria.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

More than 15,000 prescriptions and over the counter drugs are available according to the US Food and Drug Administration website. Moreover, several herbal medicines and dietary supplements are readily available to add to the list of possible drugs, which can potentially cause adverse drug interactions. These are a pressing concern for all as they can interfere with many dental procedures. Additionally, the number of geriatric patients seen in routine dental practice has increased over time. This implies that there are more patients with multiple diseases and health conditions like hypertension, diabetes, problems associated with the cardiovascular, renal and gastrointestinal systems, arthritis, osteoporosis, etc. All these require patients to be on certain medications. Furthermore, advancement in the dental field has led to more complex dental procedures (implants, grafts) being carried out in a general dental practice. These advanced and slightly more invasive treatments require the use of certain drugs before, during and after the treatment like local anesthetics, vasoconstrictors, anxiolytics, analgesics and antibiotics. All of these can possibly interact with medications a patient is already taking and can also interfere with the current dental treatment and create complications. This article aims to provide necessary information about commonly encountered systemic diseases and associated treating medications, their mechanism of action, possible complications and their management. The classes of drugs discussed include anti-platelet agents, vitamin K antagonists, novel oral anticoagulants, bisphosphonates, disease-modifying anti-rheumatic drugs and oral contraceptives.

Introduction: Studies conducted in real-life scenarios on vaccine protection against COVID-19 constitute an important global priority, but one that is currently mostly neglected in low- and middle-income countries such as Angola. Here, we analyze for the first-time vaccine protection against COVID-19 in a real-life scenario after 6 months of implementing a multi-vaccination plan in Angola, providing estimation of odds ratios in vaccinated individuals and vaccine efficacy against infection by SARS-CoV-2 in a period that coincided with the identification of the Omicron variant in the country. Methods: We used a negative test case-control design to assess the effectiveness of vaccination against confirmed SARS-CoV-2 infection. A total of 4.232 vaccinated and unvaccinated individuals with the result of a rapid antigen diagnostic test against SARS-CoV-2 performed from December 27 to 28, 2021 were included in the study. Data were extracted from the Digital Vaccination Record Platform (Rediv) of the Ministry of Health of Angola. All ethical procedures related to the authorization necessary to carry out the study were followed. Statistical analyzes were performed using version 7.5.2.0 of CDC's Epi Info. Frequency distributions and measures of central tendency were used to characterize the study universe. The general and sex-adjusted and age-adjusted odds ratios, were evaluated by comparing the chances of vaccination between cases and controls, and their associated 95% CI, which were calculated using the Mantel-Haenszel stratification method. The risk classification of Axel Kroeger, Piscoya and Alarcon was used to interpret the odds ratio. The Breslow-Day statistic was used to assess the homogeneity of the odds ratios. Vaccine efficacy was calculated using the odds ratio applying the accepted statistical vaccine efficacy formula:(1 − odds ratio) × 100. For all estimates, a P value < 0.05 was considered statistically significant. Results: The population consisted of 63.63% male and 36.37% female. The mean age was 36 years with a standard deviation of 13. 83. Regarding vaccination status, 83.27% of individuals were vaccinated and 16.73% were unvaccinated, with 21.81% positive and 78.19% negative for SARS -CoV-2. The odds of SARS-CoV-2 infection were 0.85 (95% CI 0.70 – 1.03) times lower in vaccinated compared to unvaccinated individuals, with P=0.09. The overall vaccine efficacy (VE) was 15% (95% CI -3 – 30). Conclusion: There was no statistically significant decrease in the chances of SARS-CoV-2 infection in vaccinated versus unvaccinated individuals. However, the overall vaccine efficacy was 15%.

Abstract: As a low-input crop, Miscanthus offers numerous advantages that, in addition to agricultural applications, permits its exploitation for energy, fuel, and material production. Depending on the Miscanthus genotype, season, and harvest time as well as plant component (leaf versus stem), correlations between structure and properties of the corresponding isolated lignins differ. Here, a comparative study is presented between lignins isolated from M. x giganteus, M. sinensis, M. robustus and M. nagara using a catalyst-free organosolv pulping process. The lignins from different plant constituents are also compared regarding their similarities and differences regarding monolignol ratio and important linkages. Results showed that the plant genotype has the weakest influence on monolignol content and interunit linkages. In contrast, structural differences are more significant among lignins of different harvest time and/or season. Analyses were performed using fast and simple methods such as nuclear magnetic resonance (NMR) spectroscopy. Data was assigned to four different linkages (A: b-O-4 linkage, B: phenylcoumaran, C: resinol, D: b-unsaturated ester). In conclusion, A content is particularly high in leaf-derived lignins at just under 70 % and significantly lower in stem and mixture lignins at around 60 % and almost 65 %. The second most common linkage pattern is D in all isolated lignins, the proportion of which is also strongly dependent on the crop portion. Both stem and mixture lignins, have a relatively high share of approximately 20 % or more (maximum is M. sinensis Sin2 with over 30 %). In the leaf-derived lignins, the proportions are significantly lower on average. Stem samples should be chosen if the highest possible lignin content is desired, specifically from the M. x giganteus genotype, which revealed lignin contents up to 27 %. Due to the better frost resistance and higher stem stability, M. nagara offers some advantages compared to M. x giganteus. Miscanthus crops are shown to be very attractive lignocellulose feedstock (LCF) for second generation biorefineries and lignin generation in Europe.

The importance and near ubiquity of the Golden Ratio in disciplines like chemistry and biology is well known, but only recently has it come to light in areas pertaining to the Quantum domain. By using a modified tool-kit of hyper-complex numbers (known as Dimensional Gate Operators) and numerical analysis, we uncover a connection between hyper-dimensional objects, the Fibonacci sequence and that of quasiparticles and excitations. The results show that dimensionality increases in step with the Fibonacci sequence.

As a renewable industrial crop, Miscanthus offers numerous advantages, namely high photosynthesis activity (as a C4 plant) and exceptional CO2 fixation rate. These properties make Miscanthus very attractive for industrial exploitation, such as lignin generation. Here, we present a systematic study analyzing the correlation of the lignin structure with Miscanthus genotype and plant portion (stem versus leaf). Specifically, the ratio of the three monolignols and corresponding building blocks as well as the linkages formed between the units have been studied. Depending on the Miscanthus genotype and plant component (leaf versus stem), correlations between chemical structure and properties of the lignins have been determined, i.e. correlations in molecular weight, polydispersity and decomposition temperature. Lignin isolation was performed using non-catalyzed organosolv pulping and the structure analysis includes NREL, FTIR, UV-Vis, HSQC-NMR, TGA, pyrolysis GC/MS. Structural differences were found for stem and leaf-derived lignins. Compared to beech wood lignins, Miscanthus lignins possess lower molecular weight and narrow polydispersities (< 1.5 Miscanthus vs. > 2.5 beech) corresponding to improved homogeneity. In addition to conventional univariate analysis of FTIR spectra, multivariate chemometrics revealed distinct differences for aromatic in-plane deformations of stem versus leaf-derived lignins. These results emphasize the potential of Miscanthus as low-input resource and Miscanthus-derived lignin as promising agricultural feedstock.

Research with deuterium-depleted water (DDW) in the last two decades proved that deuterium/hydrogen ratio has a key role in cell cycle regulation and cellular metabolism. The present study aimed to investigate the possible effect of deuterium-depleted organic compounds (DDOC) alone and in combination with DDW on cancer growth in two in vivo mouse models. To produce DDOC, drinking water of laying hens was replaced with DDW (25 ppm) for 6 weeks, resulting in 60 ppm D level in dried egg yolk that was used as deuterium-depleted food additive. In one model, 4T1, a cell line with high metastatic capacity to the lung, was inoculated in the mice’s mammary pad. After three weeks of treatment with DDW and/or DDOC, the tumor volume in the lungs was smaller in all treated groups vs. controls with natural D level. Tumor growth and survival in mice transplanted with MCF-7 breast cancer cell line showed that the anticancer effect of DDW was enhanced by food containing the deuterium-depleted yolk. The study confirmed the importance of D/H ratio not only in consumed water but also in metabolic water produced by the mitochondria while oxidizing nutrient molecules. This is in line with the concept that initiation of cell growth requires the cells to generate a higher D/H ratio, but DDW, DDOC, or the naturally low-D lipids in a ketogenic diet, have significant effect on tumor growth by preventing the cells from raising D/H ratio to the threshold.

Recently, representation formulae and monotonicity properties of generalized k-Bessel functions, Wk v,c., were established and studied by SR Mondal [24]. In this paper, we pursue and investigate some of their image formulae. We then extract solutions for fractional kinetic equations, involving Wk v,c, by means of their Sumudu transforms. In the process, Important special cases are then revealed, and analyzed.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

Natural capital is the wealth of nations that give them the economic status they represent. Worldwide, vulnerable people depend on natural capital for employment, salaries, wealth, and livelihoods and, in turn, determine the developmental index of the nation to which they belong. The availability of ecological services is crucial for clean water and air, food and fodder, and agricultural development. In this short commentary, we have tried to sum up the ideas and discussions over natural capital's role in ascribing economic status to countries. We have discussed how the prosperity of humans is intertwined with the services ecosystems provide and how poor natural resource management (NRM) has adversely cost human well-being. The paper concludes that to ensure the current and future human well-being, an in-depth understanding of the services ecosystems provide, is essential.

This paper intends to examine whether a company’s policy of dividend would impact or influence the price fluctuation of respective common stock in the designated stock market particularly in Hong Kong. Hence, there are 354 companies in Hong Kong which are all listed company on the Stock Exchange of Hong Kong (HKEX), were chosen as sample data for analysis with their audited financial information ranged from 2001 to 2020. Two proxies, the yield and the ratio of pay-out of dividend were widely adopted for the measurement of the effect of dividend policy and the possible influence on the volatility of respective common stock price by employing two statistical models, which are the model of fixed and random effects to provide accurate regression coefficients. With the results from the model of fixed effects, the yield and the pay-out ratio of dividend have been found statistically associated to the price volatilization of respective common stock in Hong Kong. The statical results in this study also find the yield and the ratio of pay-out of dividend are apparently and negatively associated to the price volatilization of respective common stock in Hong Kong. The research outcomes will be a reference for further study on different variables may have effects or volatilize the price of common stock price particularly in Hong Kong capital market.

Good data analysis is required for the optimal design of water resources projects. However, data are not regularly collected due to material or technical reasons, which results in incomplete-data problems. Available data and data length are of great importance to solve those problems. Various studies have been conducted on missing data treatment. This study used data from the flow observation stations on Yeşilırmak River in Turkey. In the first part of the study, models were generated and compared in order to complete missing data using ANFIS, multiple regression and Normal Ratio Method. In the second part of the study, the minimum number of data required for ANFIS models was determined using the optimum ANFIS model. Of all methods compared in this study, ANFIS models yielded the most accurate results. A 10-year training set was also found to be sufficient as a data set.

Currently, for the serious air pollution and global warming effect caused by the substance released from the present vehicle, it is expected that the regulatory requirements for the emission will become more stringent. A new concept of the combustion technology that can reduce the NOx and PM related to combustion is urgently needed. To cope with such social demands, many developed countries are efforts to develop the environment friendly vehicle engine at the national lever in order to satisfy with strengthening emission control. As a main combustion technology among new combustion technology for the new generation engine, the homogenous charge compression engine (HCCI) is expanding its application range by employing multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. In this paper, a multi-injection method in order to apply the HCCI combustion method without mainly altering engine specifications and practicality by referring to the results of the HCCI engine was investigated. Applied with forced charging, exhaust gas recirculation (EGR) and compression ratio change, it was evaluated to the possibility of securing optimum fuel economy and emission reduction in the IMEP 0.8 MPa range.

In attempting to predict the further course of the novel coronavirus (COVID-19) pandemic caused by SARS-CoV-2, mathematical models of different types are frequently employed and calibrated to reported case numbers. Among the major challenges in interpreting these data is the uncertainty about the amount of undetected infections, or conversely: the detection ratio. As a result, some models include assumptions about the percentage of detected cases among total infections while others completely neglect undetected cases. Here, we illustrate how model projections about case and fatality numbers vary significantly under varying assumptions on the detection ratio. Uncertainties in model predictions can be significantly reduced by representative testing, both for antibodies and active virus RNA, to uncover past and current infections that have gone undetected thus far.

There is high prevalence of hypertension and is rapidly increasing around the world, despite the intervention programme implemented, this study aimed at estimating the prevalence rate, test of association between hypertension and risk factors and model hypertension rate. Data used was obtained from the health record of Federal Medical Centre, Keffi from January 2016 – January 2019. Ordinal logistic regression model was used; Model Fitting Information, Goodness-of-Fit, Pseudo R-Square and Test of Parallel Lines are fitted to the data sets to test the accuracy and correctness of the model. The results indicated that the overall prevalence of hypertension rate is high at 36.4%, among the adult population, body mass index and gender are statistically significant, and Age is not significant in the study. Individuals that are overweight are more likely to be hypertensive compare to other weights. At age 40 – 49 years which have the highest rate of 26.5% and the odd ratio is 0.75 compared to others. One year increase in age 30 – 39, the cumulative odd of being hypertensive is 0.91 while other independent variables are held constant. The odd ratio of female being hypertensive is 0.85, therefore the females are more likely to be hypertensive with 54.4% compared to the males at 45.6% . There is no presence of multicolinearity among the variables and Logit models were formulated to calculate probabilities of the various possible outcomes.

Citrullinemia is the earliest identifiable biochemical abnormality in neonates with intrahepatic cholestasis due to a citrin deficiency (NICCD) and it has been included in newborn screening panels using tandem mass spectrometry. However, only one neonate was positive among 600,000 infants born in Sapporo city and Hokkaido, Japan between 2006 and 2017. We investigated 12 neonates with NICCD who were initially considered normal in newborn mass screening (NBS) by tandem mass spectrometry, but were later diagnosed with NICCD by DNA tests. Using their initial NBS data, we examined citrulline concentrations and ratios of citrulline to total amino acids. Although their citrulline values exceeded the mean of the normal neonates and 80 % of them surpassed +3SD, all were below the cutoff of 40 nmol/mL. The ratios of citrulline to total amino acids significantly elevated in patients with NICCD compared to the control. By evaluating two indicators simultaneously, we could select about 80% of patients with missed NICCD. Introducing an estimated index comprising citrulline values and citrulline to total amino acid ratios could assure NICCD detection by NBS.

Various type of soils have been identified based on their electrical and magnetic properties, especially with regards to peat soils. Peat soils are commonly considered as partly decomposed vegetation. In this study, electrical and magnetic properties have been used in K-means clustering to identify layers of peat soils. K-means clustering is a partitioning method that treats observations in the data. Data cores were obtained at every centimeter and examined for their electrical conductivity (σ) and magnetic susceptibility (χ_m) properties. A 291 cm core was obtained at Tegal Arum Village in South Kalimantan, Indonesia. The K-means clustering results indicate two different layers at 148 cm, and this is supported by loss on ignition (LOI) measurements. In the first layers, a 87.65% LOI was found associated with peat soils (above 248 cm). Whereas, in the second layers, there was a 26.11% LOI associated with mineral soils (below 248 cm). The results of this study using K-means clustering can be used to delineate soil layers.

Yogic and meditative traditions have long held that the fluctuations of the breath and the mind are intimately related. While respiratory modulation of cortical activity and attentional switching are established, the extent to which electrophysiological markers of attention exhibit synchronization with respiration is unknown. To this end, we examined 1) frontal midline theta-beta ratio, an indicator of attentional control state known to correlate with mind wandering episodes and functional connectivity of the executive control network; 2) pupil diameter (PD), a known proxy measure of locus coeruleus (LC) noradrenergic activity; and 3) respiration for evidence of phase synchronization and information transfer (multivariate Granger causality) during quiet restful breathing. Our results indicate that both TBR and PD are simultaneously synchronized with the breath, suggesting an underlying oscillation of an attentionally relevant electrophysiological index that is phase-locked to the respiratory cycle which could have the potential to bias the attentional system into switching states. We highlight the LC’s pivotal role as a coupling mechanism between respiration and TBR, and elaborate on its dual functions as both a chemosensitive respiratory nucleus and a pacemaker of the attentional system. We further suggest that an appreciation of the dynamics of this weakly coupled oscillatory system could help deepen our understanding of the traditional claim of a relationship between breathing and attention.

Clustering, or otherwise known as cluster analysis, is a learning problem that takes place without any human supervision. This technique has often been utilized, much efficiently, in data analysis, and serves for observing and identifying interesting, useful, or desired patterns in the said data. The clustering technique functions by performing a structured division of the data involved, in similar objects based on the characteristics that it identifies. This process results in the formation of groups, and each group that is formed, is called a cluster. A single said cluster consists of objects from the data, that have similarities among other objects found in the same cluster, and resemble differences when compared to objects identified from the data that now exist in other clusters. The process of clustering is very significant in various aspects of data analysis, as it determines and presents the intrinsic grouping of objects present in the data, based on their attributes, in a batch of unlabeled raw data. A textbook or otherwise said, good criteria, does not exist in this method of cluster analysis. That is because this process is so different and so customizable for every user, that needs it in his/her various and different needs. There is no outright best clustering algorithm, as it massively depends on the user’s scenario and needs. This paper is intended to compare and study two different clustering algorithms. The algorithms under investigation are k-mean and mean shift. These algorithms are compared according to the following factors: time complexity, training, prediction performance and accuracy of the clustering algorithms.

The shoulder region has the highest incidence of acute injuries in the sport of surfing. Little is known about the strength profile at the shoulder in a surfing cohort. The primary aim of this study was to establish the reliability of a rotator cuff strength testing procedure for surfers with a secondary aim of providing a profile of internal (IR) and external rotation (ER) strength in a competitive surfing cohort. Shoulder IR and ER isometric strength was measured using a hand-held dynamometer in 13 competitive surfers. Intra-class coefficient values ranged from 0.97 to 0.98 for intra rater reliability and were lower for inter rater reliability ranging from 0.80 to 0.91. Normalised force (N/Kg) for IR strength was significantly greater than ER strength bilaterally (dominant, p= 0.007, non-dominant, p<0.001). No significant differences (p< 0.79) were found in IR strength (N/Kg) between the dominant and non-dominant arms. ER strength (N/Kg) was significantly weaker on the non-dominant arm compared with the dominant arm (p<0.02). The non-dominant arm ER to IR ratio (0.82 ± 0.15) was significantly (p=0.025) lower than the dominant (0.88 ± 0.14) The current procedure is reliable with the same clinician, results indicate musculature asymmetry specific to the external rotators.

Vitamin D and ω-3 fatty acids (ω-3) co-supplementation potentially improve type 1 diabetes (T1D) by attenuating autoimmunity and counteracting inflammation.This cohort study preliminary to a randomized control trial (RCT) is aimed to evaluate, in a series of T1D children assuming Mediterranean diet and taking cholecalciferol 1000U/day fromT1D onset, if ω-3 co-supplementation preserves the residual endogen insulin secretion (REIS).Therefore, 22 new onsets of 2017 received ω-3 [eicosapentenoic acid (EPA) plus docosahexaenoic acid (DHA), 60mg/kg/day], and were compared retrospectively vs. 37 previous onsets without ω-3 supplementation. HbA1c%, daily insulin demand (IU/Kg/day) and IDAA1c, a composite index (calculated as IU/Kg/dayx4 + HbA1c%) as surrogate of REIS, were evaluated at recruitment (T0) and 12 months later (T12). In the ω-3 supplemented group, dietary intakes were evaluated at T0 and T12. As outcome, decreased insulin demand (p<0.01), particularly pre-meal boluses (p<0.01), and IDAA1c (p<0.05), were found in the ω-3 group while HbA1c% were not different in the two groups. Diet analysis, at T12 vs. T0, showed that the intake of arachidonic acid (AA) was decreased (p<0.01) in the ω-3 supplemented group while other nutrients were unchanged; at T0, the AA intake was inversely correlated with HbA1c% (p<0.05; r;.0.411). In conclusion, the results suggest that vitamin D plus ω-3 co-supplementation and AA reduction in Mediterranean diet display benefits for T1D children and deserve further investigation.

Monitoring drought impacts in forest ecosystems is a complex process, because forest ecosystems are composed of different species with heterogeneous structural compositions. Even though forest drought status is a key control on the carbon cycle, very few indices exist to monitor and predict forest drought stress. The Forest Drought Indicator (ForDRI) is a new monitoring tool developed by the National Drought Mitigation Center (NDMC) to identify forest drought stress. ForDRI integrates 12 types of data, including satellite, climate, evaporative demand, ground water, and soil moisture, into a single hybrid index to estimate tree stress. The model uses Principal Component Analysis (PCA) to determine the contribution of each input variable based on its covariance in the historical records (2003–2017). A 15-year time series of 780 ForDRI maps at a weekly interval were produced. The ForDRI values at a 12.5km spatial resolution were compared with normalized weekly Bowen ratio data, a biophysically based indicator of stress, from nine AmeriFlux sites. There were strong and significant correlations between Bowen ratio data and ForDRI at sites that had experienced intense drought. In addition, tree ring annual increment data at eight sites in four eastern U.S. national parks were compared with ForDRI values at the corresponding sites. The correlation between ForDRI and tree ring increments at the selected eight sites during the summer season ranged between 0.46 and 0.75. Generally, the correlation between the ForDRI and normalized Bowen ratio or tree ring increment are reasonably good and indicate the usefulness of the ForDRI model for estimating drought stress and providing decision support on forest drought management.

We propose a wave-like design on the surface of cathode channels (wave form cathode channels) to improve oxidant delivery to gas diffusion layers (GDLs) [1-2]. We performed experiments using PEMFCs combined with wave form surface design on cathodes. We varied the factors of the distance between wave-bumps (the Adhesive distance, AD), and the size of the wave-bumps (the Expansion ratio, ER). The ADs are 3, 4, and 5 times the size of the half-circle bump’s radius, and the ERs are 1/1.5, 1/2, and 1/3 times the channel’s height. We evaluated the performances of the fuel cells, and compared the current-voltage (I-V) relations. For comparison, we prepared PEMFCs with conventional flat-surfaced oxygen channels. Our aim in this work is to identify fuel cell operation by modifying the surface design of channels, and ultimately to find the optimal design of cathode channels that will maximize fuel cell performance.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

Why are pieces of spaghetti generally broken into three to ten segments instead of two as one thinks? How can one obtain the desired number of fracture segments? For these problems, in this paper a strand of spaghetti is considered an elastic rod, and the finite-element software ABAQUS is used to simulate the detailed fracture dynamics of the elastic rod. By changing the size (length and diameter) of the rod, the relevant data on the fracture limit curvature and the number of fractured segments of the elastic rod are obtained. The ABAQUS simulation results confirm the scientific judgment of B. Audoly and S. Neukirch (Fragmentation of rods by cascading cracks: Why spaghetti does not break in half. Phys Rev Lett 95: 095505). Using dimensional analysis to fit the finite-element data, two relations of the elastic rod fracture dynamics are obtained: (1) the relationship between the fracture limit curvature and the diameter, and (2) the relationship between the number of fracture segments and the diameter-length ratio. Results reveal that when the length is constant, the larger the diameter (the smaller the diameter-length ratio D/L), the smaller the limit curvature; and the larger the diameter-length ratio D/L, the fewer the number of fractured segments. The relevant formulations can be used to obtain the desired number of broken segments of spaghetti by changing the diameter-to-length ratio.

Nowadays, the research and development of on-chip LiDAR sensors for vehicle collision avoidance is growing very fast. Therefore, the assessment of the reliability in obstacle detection using the information provided by LiDAR sensors has become a key issue to be explored by the scientific community. This paper presents the design and implementation of a self-tuning method in order to maximize the reliability of an Internet-of-Things sensors network and to minimize the number of sensors to localize with the required accuracy obstacles by a detection threshold. In order to achieve this goal, models that predict accuracy (i.e., prediction error) for object localization using data collected by LIDAR sensors are designed and implemented in Webots Automobile 3D simulation tool. The approach is based on combining different techniques. Firstly, point-cloud clustering technique and an error prediction model library composed by a multilayer perceptron neural network with backpropagation, k-nearest neighbors and linear regression are explored. Secondly the above-mentioned techniques for modeling are also combined with a supervised and reinforcement machine learning technique, Q-learning in order to minimize the detection threshold. In addition, a IoT driving assistance simulated scenario with a LiDAR sensor network is designed in order to validate the prediction model and the optimal configuration of the sensor network to guarantee reliability in obstacle localization. The results demonstrate that the self-tuning method is appropriate to increase the reliability of the sensor network whereas minimizing the detection threshold

At present more than 9 million people die of cancer every year. Simple and broad-spectrum drugs are still an urgent need for cancer patients. Recently, we proposed a new hypothesis that intracellular osmotic pressure (IOP) is the driving force of cell division, and abnormal tumor proliferation is the result of uncontrolled IOP in cells. On the one hand, aneuploidy and abnormal function of Na⁺/K⁺ pump lead to a faster rise of IOP in tumor cell than normal cells, on the other hand, abnormality of cytoskeleton assembly leads to the decrease of tolerance limit of cell membrane (TLCM) of tumor cells for resisting IOP. This hypothesis predicts: 1)Tumor cells were more intolerant to hypotonic stress than normal cells. 2) Maligancies may be sellectively killed by a suddenn increase of IOP and combined with decrease of the TLCM of tumors. Na⁺/K⁺ pump inhibitors can promotely increase the IOP of tumor cells and cytoskeleton inhibitors can dramatically lower the TLCM of tumor cells. Therefore, Na⁺/K⁺ pump and cytoskeleton inhibitors may have a synergetic effect to kill tumor cells. 3) Molecules regulating cell osmolality may be new targets for cancer treatment.

Glaucoma is a disease associated with retina of eye. Presently, millions of human being is suffering from this disease. Early detection of these diseases can save the people from blindness. Therefore, various methods have been developed for its detection. In this paper, we have studied the reported methods and summarized their performance in terms of accuracy of detection.

Quadruplex-interactive small molecules have a wide potential application, not only as drugs but also as sensors of quadruplexes structures. The purpose of this work is the synthesis of analogues of the bis-methylquinolinium-pyridine-2,6-dicarboxamide G4 ligand 360A, to identify relevant structure-activity relationships to apply to the design of other G4-interactive small molecules bearing bis-quinoline or bis-isoquinoline moieties. Thermal denaturation experiments revealed that non-methylated derivatives with a relative 1,4 position between the amide linker and the nitrogen of the quinoline ring are moderate G4 stabilizers, with a preference for the hybrid h-Telo G4. Insertion of a positive charge upon methylation of quinoline/isoquinoline nitrogen increases compounds capacity to selectively stabilize G4s compared to duplex DNA, with a preference for parallel structures. Among these, compounds having a relative 1,3-position between the charged methylquinolinium/isoquinolinium nitrogen and the amide linker are the best G4 stabilizers. More interestingly, these ligands showed different capacities to selectively block DNA polymer-ization in a PCR-stop assay and to induce G4 conformation switches of hybrid h-Telo G4. Mo-lecular dynamic simulations with the parallel k-RAS G4 structure showed that the relative spatial orientation of the two methylated quinoline/isoquinoline rings determines the ligands mode and strength of binding to G4s.

This paper considers the detection of fluctuating target in heavy-tailed clutter through the use of dynamic programming based on track-before-detect (DP-TBD) in radar systems. The clutter is modeled in terms of K-distribution, which can be widely used to describe non-Gaussian clutter received from high-resolution radars and radars working at small grazing angle. Swerling type 1 is considered to describe the target fluctuation between scans. Conventional TBD techniques suffer from significant performance loss in heavy-tailed environments due to the more frequent occurrences of target-like outliers. In this paper, we resort to DP-TBD algorithm based on prior information, which can enhance the detection performance by using the environment and target fluctuating information during the integration process of TBD. Under non-Gaussian background, the expressions of the likelihood ratio merit function for Swerling type 1 target are derived first. However, the closed analytical form of the merit function is difficult to be obtained. In order to reduce the complexity of evaluating the merit function and the computational load, an efficient approximation method as well as a two-stage detection approach is proposed and used in the integration process. Finally, several numerical simulations of the new strategy and the comparisons are presented to verify that the proposed algorithm can improve the detection performance, especially for fluctuating target in heavy-tailed clutter.

A Pogorelov polytope is a combinatorial simple 3-polytope realizable in the Lobachevsky (hyperbolic) space as a bounded right-angled polytope. It has no 3- and 4-gons and may have any prescribed numbers of k-gons, k ≥ 7. Any polytope with only 5-, 6- and at most one 7-gon is Pogorelov. For any other prescribed numbers of k-gons, k ≥ 7, we give an explicit construction of a Pogorelov and a non-Pogorelov polytopes. Any Pogorelov polytope different from Löbel polytopes can be constructed from the 5- or the 6-barrel by cuttings off pairs of adjacent edges and connected sums with the 5-barrel along a 5-gon with the intermediate polytopes being Pogorelov. For fullerenes there is a stronger result. Any fullerene different from the 5-barrel and the (5, 0)-nanotubes can be constructed by only cuttings off adjacent edges from the 6-barrel with all the intermediate polytopes having 5-, 6- and at most one additional 7-gon adjacent to a 5-gon. This result can not be literally extended to the latter class of polytopes. We prove that it becomes valid if we additionally allow connected sums with the 5-barrel and 3 new operations, which are compositions of cuttings off adjacent edges. We generalize this result to the case when the 7-gon may be isolated from 5-gons.

This paper is the continuation of a previous study, which highlighted some inconsistencies in the RILEM guidelines for the interpretation of the diagonal compression test. Although improved compared to the ASTM guidelines, in fact, the RILEM guidelines underestimate the state of hydrostatic stress induced by the diagonal compression test at the center of the wallette. The new interpretation of the diagonal compression test proposed in this article shows that the RILEM guidelines actually underestimate both the hydrostatic and the deviatoric stress states at the center of the wallette. The new formulation complies with the linear elastic theory and allows us to use the the diagonal compression test to identify the three elastic coefficients of masonry. In particular, it allows the identification of the Poisson ratio, which instead takes on a conventional value in the RILEM and ASTM guidelines. The difference of one order of magnitude between the conventional and proposed Poisson’s ratio is in agreement with the experimental results on another brittle material, namely concrete. Finally, the new proposal fills the gap between the results provided by the two tests usually performed to identify the shear behavior of masonry: the diagonal compression test and the shear-compression test.

A non-Newtonian fluid model is used to investigate the two-dimensional pulsatile blood flow through a tapered artery with a stenosis. The mixed convection effects of heat and mass transfer are also taken into account. By applying non-dimensionalization and radial coordinate transformation, we simplify the system in a tube. Under the finite difference scheme, numerical solutions are calculated for velocity, temperature concentration, resistance, impedance, wall shear stress and shearing stress at the stenosis throat. Finally, Quantitative analysis is carried out.

In this paper, we consider the relation of more than four harmonic points in a line. For this purpose, starting from the dependence of the harmonic points, Desargues’ theorems, and perspectivity, we note that it is necessary to conduct a generalization of the Desargues’ theorems for projective complete n-points, which are used to implement the definition of the generalization of harmonic points. We present new findings regarding the uniquely determined and constructed sets of H-points and their structure. The well-known fourth harmonic points represent the special case (n=4) of the sets of H-points of rank 2, which is indicated by P42.

Pancreatic cancer is a fatal disease with mortality rate of 5% and a with a limited survival rate of 5 years. Despite of the extensive efforts that has been made to cure the disease it still has been considered as ‘undruggable’. It is characterized by epithelial to dense stromal tumor formation however due to lack of diagnosis options and treatment test available to detect the disease to the point at which resection of the tumor is possible, it makes it the fourth leading cause of cancer related death. The unavailable information regarding the early detection of biological markers along with the increased invasive tumor, the inherit chemoresistance against medication radiation and chemotherapy stubbornly fail the therapeutic options available. These associated problems made the scientists to reevaluate the approaches that are currently in practice and take a step back to fully understand the basic biological pathways that are involved in the pancreatic cancer, the heterogeneity of the tumor itself along with expression and a number of mutations that are observed at different locations. Clinical trial along with new approaches are nowadays focus of research to treat this tumor. The review paper describes the basic cellular pathways involved in pancreatic cancer, the gene mutations and their expression having effect on the pathology of the diseases along with treatment options that are available to treat the tumor. These efforts will help with the expansion of our knowledge to undergo the clinical trial and the synthesis of novel medicines for the prognosis of the disease.

The violation of privacy, others people or personal, is a very current problem, which concerns not only on the web but also in private life. In the years 1990 it was expected that nowadays, that any routine operation was carried out "manually", and it would be performed through mobile phones or personal computers. The problem pertains the distribution network that allows to share and bring together information and as result the network becomes unsafe, if subjected to attacks. Nowaday we put personal information on web because otherwise we are seen as “weak”. This work aims to measure and analyze how much information are shared by users of a pre-established social network and it is carried out through a set of algorithms techniques of machine learning.

In this paper, we provide some enlightening examples of the application of Clifford algebra in geometry, which show the concise representation, simple calculation and profound insight of this algebra. The definition of Clifford algebra implies geometric concepts such as vector, length, angle, area and volume, and unifies the calculus of scalar, spinor, vector and tensor, so that it is able to naturally describe all variables and calculus in geometry and physics. Clifford algebra unifies and generalizes real number, complex, quaternion and vector algebra, converts complicated relations and operations into intuitive matrix algebra independent of coordinate systems. By localizing the basis or frame of space-time and introducing differential and connection operators, Clifford algebra also contains Riemann geometry. Clifford algebra provides a unified, standard, elegant and open language and tools for numerous complicated mathematical and physical theories. Clifford algebra calculus is an arithmetic-like operation that can be well understood by everyone. This feature is very useful for teaching purposes, and popularizing Clifford algebra in high schools and universities will greatly improve the efficiency of students to learn fundamental knowledge of mathematics and physics. So Clifford algebra can be expected to complete a new big synthesis of scientific knowledge.

The experiments of Project 8 have been excellent, but the expected goals still difficult to achieve. So much so that some of the results at your fingertips were also missing. In view of this, the focus of this article is to clarify several easy confused concepts. Only in this way, we can reasonably explain the experimental data. The main points are as follows: 1. The value c of the light speed in vacuum and a particle with zero static mass, both of which do not exist in the reality. That is to say, the so-called a photon's static mass is equal to zero but has energy, which is a paradox that confuses two different definitional domains. 2. In the reality, photons are high-speed particles generated by electromagnetic radiation. They must have the characteristics of (static) mass, energy and wave, in order to describe the main body to aim at photons from different angles. 3. After any main body comes into being electromagnetic radiation, its static mass will inevitably decrease accordingly. 4. The charge-mass ratio of an electron is a physical constant, which is the ratio of its charge to the amount of matter, and is not affected by relativistic effects and electromagnetic radiation. 5. The uncertainty of moving electrons is caused by random electromagnetic radiations. Finally, it is pointed out that if the cyclotron frequency of a single electron is measured, and at the same time, its de Broglie wavelength or frequency can also be measured, then its static mass can be obtained. Even so, the expected goals are still difficult to achieve, because random electromagnetic radiations are always taking away continually the matter composition of the single electron being measured. However, this was precisely a result of the research obtained by Project 8, and had universality, which should be reflect on.

The purpose of this study is nutrient resources recovery by achieving the optimal chemical oxygen demand (COD) and carbon to nitrogen ratio (C/N) in co-composting wastewater treatment plant sludge with Municipal Solid Wastes (MSW). In this effort, the co-composting has been conducted in form of a case study in the northern region of Iran. In this research, 192 tests were carried out on four series of samples examined in terms of waste to sludge ratio, different aeration period, the percent of porous materials and the moisture content. This study was carried out at a temperature of 50 °C for a 15 day period by application of the in-vessel system and shows that the best ratio for waste to sludge is 2:1, while the 8 hour period is the best aeration period. The porous material which can be added to the composting process is limited to 15% in weight. In other words, any more or less amount of this material will adversely impact the process. Moreover, this research suggests that the sludge dewatering is not required in such processes. In Addition, the efficiency of both COD and C/N reductions equals to about 40%.

Classical k-ratio models, e.g. ZAF and phi(rho z), used in electron probe microanalysis (EPMA) assume a homogeneous or multi-layered material structure, which essentially limits the spatial resolution of EPMA to the size of the interaction volume where characteristic x-rays are produced. We present a new model for characteristic x-ray emission that avoids assumptions on the material structure to not restrict the resolution of EPMA a-priori. Our model bases on the spherical harmonic (PN) approximation of the Boltzmann equation for electron transport in continuous slowing down approximation. PN models have a simple structure, are hierarchical in accuracy and well-suited for efficient adjoint-based gradient computation, which makes our model a promising alternative to classical models in terms of improving the resolution of EPMA in the future. We present results of various test cases including a comparison of the PN model to a minimum entropy moment model as well as Monte-Carlo (MC) trajectory sampling, a comparison of PN-based k-ratios to k-ratios obtained with MC, a comparison with experimental data of electron backscattering yields as well as a comparison of PN and Monte-Carlo based on characteristic X-ray generation in a three-dimensional material probe with fine structures.

Background Telomere shortening is related to aging and unfavourable health outcomes. Obesity and metabolic diseases are important factors for accelerating aging. This study aimed to find out the association between obesity, metabolic disease, and telomere length in metabolically healthy adults. Methods 237 adults were enrolled with written consents at a health promotion centre of a tertiary hospital from February 2014 to March 2015. After excluding 99 subjects who met the exclusion criterion, a total of 130 metabolically healthy subjects were selected for final analysis. The subjects were divided into quartile groups according to the telomere lengths of their oral mucosal cells. Results The subjects consisted of 66 (50.8%) males with a mean age of 58.59 years. The body mass index (BMI, kg/m2) increased significantly along with the quartile groups (Q1, 23.00; Q2, 23.96; Q3, 23.70; Q4, 25.20; P-for trend=0.008). Waist circumference (WC, P-for trend=0.022), waist-to-hip ratio (WHR, P-for trend=0.005), and waist-to-height ratio (WHtR, P=0.001) also increased along with the quartile groups. Obesity prevalence (BMI ≥25 kg/m2), abdominal obesity (WC ≥90 cm for men, ≥85 cm for women), WHR 〉1.0 for men or 〉0.85 for women, and WHtR ≥0.5 increased significantly as the telomere length increased (P-for trend <0.05). After adjusting for covariates, the ORs for each obesity markers increased as the telomere length increased (P-for trend <0.05); and the ORs of WHtR were especially meaningful (Q1, 1.00; Q2, 2.53; Q3, 2.97; Q4, 7.81; P-for trend = 0.001). There were no significant trends for metabolic syndrome and its components along with the prevalence of fatty liver disease. Conclusion Obesity markers and telomere length had significant positive correlation despite the established theory. The obesity paradox may exist in metabolically healthy adults with regard to telomere length, However, further studies with larger sample sizes for the association between obesity and telomere length are needed.

Segmentation of a region of interest is an important pre-processing step for many colour image analysis techniques. Similarly segmentation of plant in digital images is an important preprocessing step in phenotying plants by image analysis. In this paper we present an analytical study to statistically determine the suitability of colour space representation of an image to best detect plant pixels and separate them from background pixels. Our hypothesis is that the colour space representation in which the separation of the distributions representing plant pixels and background pixels is maximized would be the best for detection of plant pixels. The two classes of pixels are modelled as a Gaussian mixture model (GMM). In our GM modelling we don't make any prior assumption about the number of Gaussians in the model. Rather a constant bandwidth mean-shift filter is used to cluster the data and the number of clusters and hence the number of Gaussians is automatically determined. Here we have analysed following representative colour spaces like $RGB$, $rgb$, $HSV$, $Ycbcr$ and $CIE-Lab$. This is because these colour spaces represent several other similar colour spaces and also an exhaustive study of all the colour space will be too voluminous. We also analyse the colour space feature from the two-class variance ratio perspective and compare the results of our hypothesis with this metric. The dataset for this empirical study consist of 378 digital images of plants and their manual segmentation. Dataset consist of various species of plants (arabidopsi, tobacco, wheat, rye grass etc.) imaged under different lighting conditions, indoor and outdoor, controlled and uncontrolled background. In results we obtain better segmentation of the plants in $HSV$ colour space, which is supported by its Earth mover distance (EMD) on the GMM distribution of plant and background pixels.

By combing continuum topology optimization (TO) method and lattice structure technique, a sandwich aircraft spoiler with a high stiffness-to-weight is designed. TO method is served to produce the shell of the aircraft spoiler and the lattice structure, used as cores, is employed to support the shell. TO problem is established as maximizing the stiffness of the structure with limited material volume. Density-based method is utilized to achieve a 0/1 solution. We then empirically replace the core of the aircraft spoiler by using 3D kagome lattice structure. Two different materials, i.e., aluminum alloy and titanium alloy, are synthetically applied to further reduce the weight and simultaneously improve the strength of the aircraft spoiler. Numerical simulations are conducted to show that the designed aircraft spoiler can meet the service environment with a reduction of its weight by approximately 80% when compared with that of the initial design model. Finally, we have fabricated the designed model with photosensitive resin by using 3D printing technique.

Trichomes are a common morphological defense against pests, in particular, type IV glandular trichomes have been associated with resistance against different invertebrates. Cultivated tomatoes usually lack or have a very low density of type IV trichomes. Thus, specific breeding programs to incorporate these natural defences, that are common within the Solanum genus, might improve a more sustainable management. We have identified a S. pimpinellifolium accession with very high density of this type of trichomes. Two F2 mapping populations using two different parents have been developed, characterized and genotyped using a new genotype methodology, K-seq. We have been able to build an ultra-dense genetic map with 147,326 markers with an average distance between markers of 0.2 cM that has allowed us to perform a detailed mapping. We have used two different families and two different approaches, QTL mapping and QTL-seq, to identify several QTLs implicated in the control of trichome type IV developed in this accession on the chromosomes 5, 6, 9 and 11. The QTL located on chromosome 9 is a major QTL that has not been previously reported in S. pimpinellifolium that increases by a factor of 9 the density of trichomes.

In this work, numerical simulations for the absorption and scattering efficiencies of spheroid core–shell nanoparticles (CSNs) were conducted and studied using the discrete-dipole approximation method. The characteristics of surface plasmon resonances (SPR) depend upon shell thickness, the compositions of the core and shell materials, and the aspect ratio of the constructed CSNs. We used different core@shell compositions, specifically Au@SiO₂, Ag@SiO₂, Au@TiO₂, Ag@TiO₂, Au@Ag, and Ag@Au, for extinction spectra analysis. We also investigated coupled resonance mode wavelengths by adjusting the composition’s layer thickness and aspect ratio. In this study, we show that the extinction efficiency of the Ag@TiO₂ core–shell nanoparticles (CSNPs) was higher than that of the others, and we examined the impact of TiO₂ shell thickness and Ag core radius on SPR peak positions. From the extinction spectra we found that the Ag@TiO₂ nanoparticle had better refractive index sensitivity and figure of merit when the aspect ratio was set to 0.3. All of the experimental results proved that the tunability of these plasmonic resonances was highly dependent on the material used, the layer thickness, and the aspect ratio of the core@shell CSNPs.

The Lamiaceae belong to the species-richest families of flowering plants and harbor many species used as herbs or for medicinal applications, such as Basils or Mints. Evolution of this group has been driven by chemical speciation, mainly of Volatile Organic Compounds (VOCs). The commercial use of these plants is characterized by a large extent of adulteration and surrogation. To authenticate and discern the species, is, thus, relevant for consumer safety, but usually requires cumbersome analytics, such as Gas Chromatography, often to be coupled with Mass Spectroscopy. We demon-strate here that quartz-crystal microbalance (QCM)-based electronic noses provide a very cost-efficient alternative, allowing for a fast, automated discrimination of scents emitted from leaves of different plants. To explore the range of this strategy, we used leaf material from four genera of Lamiaceae along with Lemongrass as similarly scented, but non-related outgroup. In order to unambiguously differentiate the scents from the different plants, the output of the 6 different SURMOF/QCM sensors was analyzed using machine learning (ML) methods, together with a thorough statistical analysis. The exposure and purging datasets (4 cycles) obtained from a QCM-based, low-cost homemade portable e-Nose were analyzed with Linear Discriminant Analysis (LDA) classification model. Prediction accuracies with repeating test measurements reached values of up to 90%. We show that it is not only possible to discern and identify plants on the genus level, but even to discriminate closely related sister clades within a genus (Basil), demonstrating that e-Noses are a powerful technology to safeguard consumer safety against the challenges of globalized trade.

Control of nutrients, mainly nitrogen (N) and phosphorus (P), plays a significant role in preventing cyanobacterial blooms (harmful algal blooms (HABs)). This study aimed at evaluating changes in the risk of the occurrence of cyanobacterial blooms and advancing the understanding of how N and P affect the growth of cyanobacteria in a eutrophic lake, Lake Vombsjön, in southern Sweden. Statistical analysis was used to demonstrate the pattern of cyanobacterial blooms, that the highest content present in September and the later that algal blooms occur, the more likely it is a cyanobacterial bloom as cyanobacteria became dominating in October and November (90%). Two hypothesises tested in Lake Vombsjön confirmed namely that a high total phosphorus (TP) level correlates with an abundance of cyanobacteria and that low N:P ratio (total nitrogen/total phosphorus < 20) favours the growth of cyanobacteria. To control the growth of cyanobacteria in Lake Vombsjön, the TP level should be kept below 20 µg/L and the N:P ratio be maintained at a level of over 20. The two species Planktothrix agardhii, and Pseudanabaena spp. should be carefully monitored especially in late autumn. Future work should consider any high degree of leakage from the sediment of the dissolved phosphorus available there.

Imaging techniques such as computed tomographies (CT) play a major role in clinical imaging and diagnosis of malignant lesions. In recent years, spectral CT has emerged in the field of computed tomographies, utilizing detailed information from extracted spectral parameters of the specimen. Metal nanoparticle platforms enable effective payload delivery for this technique. Due to the possibility of surface modification, metal nanoparticles are predestined to facilitate molecular tumor targeting. In this work, we demonstrate the feasibility of anti-plasma membrane Heat shock protein 70 functionalized gold nanoparticles (AuNPs) for tumor specific multimodal imaging. Membrane-associated Hsp70 is exclusively presented on the plasma membrane of malignant cells of multiple tumor entities, but not on corresponding normal tissue cells, predestining this target epitope for tumor-selective in vivo targeting. In vitro microscopical analysis revealed the presence of cmHsp70.1-AuNP in the cytosol of tumor cell lines, being internalized via the endosomal-lysosomal pathway. In tumor bearing mice the biodistribution as well as the intratumorally enrichment of AuNP were examined 24h after i.v. application, in vivo. In parallel to spectral CT analysis, histological analysis confirmed the presence of tumor cells. In contrast to control NP, a significant enrichment of cmHsp70.1-AuNPs has been detected selectively in tumors of different preclinical mouse models. Furthermore, the biodistribution of AuNP, following i.v. injection, was analyzed by a machine-learning approach on digitalized slides. In summary, utilizing mHsp70 on tumor cells for guidance of cmHsp70.1 antibody functionalized nanoparticles enables sufficient enrichment and uniform distribution of AuNPs in mHsp70-expressing tumor cells, adequate for various microscopical imaging techniques and spectral-CT-based tumor delineation, in vivo.

The purpose of this article is to simulate data transmission and calculate traffic parameters in SAGIN air segment for which Ad Hoc network of flying drones is considered as a model. Traffic modeling is based on the manet-routing-compare example from the ns3 simulator library, which has been supplemented with the code for calculation packet losses, throughput/goodput, and message transmission delays. The program allowed considering drones movement at both low and high speeds from 3.6 km/h to 72 km/h. The dependences of traffic losses on data transmission power, transaction sizes and data transmission rate are obtained and analyzed. The distribution of the average effective arrival rate λ and the throughput/goodput for drones has been studied. Comparing traffic characteristics in models with different numbers of drones allows judging how the required quality of service can be achieved by choosing the right transmission parameters.