Increasing of the imaging rate of conventional atomic force microscopy (AFM) is almost impossible without impairing of the imaging quality, since the probe tip tends to lose contact with the sample. We propose to apply the additional nonlinear force on the upper surface of a cantilever, which will help to keep the tip and surface in contact. In practice this force can be produced by the precisely regulated airflow. Such an improvement affects the AFM system dynamics, which were evaluated using a mathematical model presented in this paper. The model defines the relationships between the additional nonlinear force, the pressure of the applied air stream and the initial air gap between the upper surface of the cantilever and the end of the air duct. It was found that the nonlinear force created by the stream of compressed air (aerodynamic force) prevents the contact loss caused by the high scanning speed or higher surface roughness, and at the same time has minimal influence on the interaction force, thus maintaining stable contact between the probe and the surface. This improvement allows to effectively increase the scanning speed by at least 10 times using a soft (spring constant of 0.2 N/m) cantilever by applying the air pressure of 40 Pa. If a stiff cantilever (spring constant of 40 N/m) is used, the potential of accuracy improvement reaches 92 times. This method is suitable for use with different types of AFM sensors and can be implemented practically without essential changes in AFM sensor design.

The purpose of this study was to assess if self-regulation of intensity based on rating of perceived exertion (RPE) is a reliable method to control the intensity of metabolic conditioning of functional-fitness session. In addition, the relationship between RPE and changes in heart rate and lactate responses was also analyzed. Eight male participants (age 28.1 ± 5.4 years; body mass 77.2 ± 4.4kg; VO₂max: 52.6 ± 4.6 mL·(kg·min)⁻¹) completed three randomly sessions (5 to 7 days apart) under different conditions: (1) all-out (ALL); (2) self-regulation of intensity based on a RPE of 6 (hard) on the Borg CR-10 scale (RPE6); and (3) a control session. Rate of perceived exertion, LAC and HR response were measured pre, during and immediately after the sessions. The RPE and LAC during the ALL-OUT sessions were higher (p ≤ 0.05) than the RPE6 and control sessions for all the analyzed time points during the sessions. Regarding HR, the 22 min area under the curve of HR during ALL-OUT and RPE6 sessions were significantly higher (p ≤ 0.05) than the control session. The average number of repetitions was lower (p ≤ 0.05) for the RPE6 session (190.5 ± 12.5 repetitions) when compared to the ALL session (214.4 ± 18.6 repetitions). There was a significant correlation between RPE and LAC (p = 0.001; r = 0.76; very large) and number of repetitions during the session (p = 0.026; r = 0.55; large). No correlation was observed between RPE and HR (p = 0.147; r = 0.380). These results indicate that self-regulation of intensity of effort based on RPE may be a useful tool to control exercise intensity during a metabolic conditioning session of functional-fitness.

The identification of informal settlements in urban areas is an important step in developing and implementing pro-poor urban policies. Understanding when, where and who lives inside informal settlements is critical to efforts to improve their resilience. This study aims to analyse the capability of machine-learning (ML) methods to map informal areas in Jeddah, Saudi Arabia, using very-high-resolution (VHR) imagery and terrain data. Fourteen indicators of settlement characteristics were derived and mapped using an object-based ML approach and VHR imagery. These indicators were categorised according to three different spatial levels: environ, settlement and object. The most useful indicators for prediction were found to be density and texture measures, (with random forest (RF) relative importance measures of over 25% and 23% respectively). The success of this approach was evaluated using a small, fully independent validation dataset. Informal areas were mapped with an overall accuracy of 91%. Object-based ML as a hybrid approach performed better (8%) than object-based image analysis alone due to its ability to encompass all available geospatial levels.

Background: Active case finding for TB was implemented in selected sixty high TB burden wards of Kolkata, India. Community volunteers called TOUCH agents (TAs) identified and referred presumptive TB patients (PTBPs) to health facilities for TB diagnosis and treatment. We aimed to describe the ‘care cascade’ of PTBPs identified during July to December, 2018 and to explore the reasons for attrition as perceived by TAs and PTBPs. Methods: An explanatory mixed methods study with quantitative phase of cohort study using routinely collected data followed by descriptive qualitative study with in-depth interviews was conducted. Results: Of the 3, 86,242 individuals enumerated, 1132 (0.3%) PTBPs were identified. Only 713 (63.0%) PTBPs visited referred facility for TB diagnosis. TB was diagnosed in 177 (24.8%) and the number needed to screen for one TB was 2,183 individuals. The potential reasons for low yield were stigma and apprehension about TB, distrust about TA, wage loss for attending health facilities and substance abuse among PTBPs. Conclusion: The yield of ACF was suboptimal with low PTBP identification rate and high attrition rate. Interviewing each individual for symptoms of TB and supporting PTBPs for diagnosis through sputum collection and transport can be adopted to improve the yield.

The purpose of this study is to investigate the moderating effect of technology configuration capability on the relationship between strategic flexibility and organizational performance through different stages of technological life cycle. Through the empirical research on the 439 Chinese high-tech organizations, it shows that a technological configuration capability has enhanced the effect of strategic flexibility to the organizational performance in the complex dynamic environment. However, the impact on the different stages of technological life cycle is different. In addition, this paper explored strategic flexibility on different stages of technological life cycle on the basis of empirical study.

Continuous ultrasonic in-situ monitoring for industrial applications is difficult owing to the high operating temperatures in industrial fields. It is expected that ultrasonic transducers consisting of CaBi4Ti4O15(CBT)/Pb(Zr,Ti)O3(PZT) sol-gel composite could be one solution for ultrasonic nondestructive testing (NDT) above 500 C because no couplant is required and CBT has a high Curie temperature. To verify the high temperature durability, CBT/PZT sol-gel composite films were fabricated on titanium substrates by spray coating, and the CBT/PZT samples were tested in a furnace at various temperatures. Reflected echoes with a high signal-to-noise ratio were observed up to 600 C. A thermal cycle test was conducted from room temperature to 600 C, and no significant deterioration was found after the second thermal cycle. To investigate the long-term high-temperature durability, a CBT/PZT ultrasonic transducer was tested in the furnace at 600 °C for 36 h. Ultrasonic responses were recorded every 3 h, and the sensitivity and signal-to-noise ratio were stable throughout the experiment.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

Sugar-sweetened beverages are associated with metabolic dysfunction, particularly in those with increased risk factors. Artificial sweeteners (AS) are often promoted as a healthier alternative, yet findings remain conflicting as to their effects on metabolic function. Further, there is a lack of data exploring the interaction between AS and high-fat diets (HFD). We therefore examined the effects of HFD and the AS Acesulfame-potassium (Ace-K) on glucose intolerance and adipose tissue physiology in male and female C57BL/6 mice. 40 mice were randomised to receive either a) a control diet (CDCon; standard control diet/water), b) control diet and Ace-k (CDAS; CD/7.5mM AS in drinking water), c) HFD (HFCon; HFD (45%kcal from fat)/water), or d) HF and AS (HFAS; HFD/7.5mM AS in drinking water) for 6 weeks. A HFD increased body weight in male and female mice independently of AS supplementation. AS induced sex-specific effects protecting against HFD-induced hyperglycaemia and adipocyte hypertrophy in male mice and reducing inflammatory gene expression in the adipose tissue. Conversely in females, AS induced hyperinsulinemia in HFD mice and increased expression of immune-related genes. These findings suggest that supplementation of HFD with AS exacerbates metabolic dysfunction in female mice. This work supports the importance of studying sexually dimorphic responses to an altered nutritional environment and highlights the need for further investigation into the intake of AS, particularly in those already at risk of metabolic disease such as the obese or overweight.

Directed energy deposition (DED) is an efficient method to fabricate functionally graded materials (FGMs) with gradient composition and complex structures, allowing for local tailoring of properties instead of the costly need for extraneous welds and joints. In this study, a FGM from stainless steel to Inconel alloy was successfully fabricated using the powder-based laser DED. A very refined grain structure has been observed in at the composition with 75 wt.% Inconel alloy content, which also exhibits the highest (entropy). For the first time, the post heat treatments, microstructure and aging precipitation behaviors of FGMs were systematically studied via experimental characterization and computation, to elucidate their effects on the gradient smoothing and mechanical properties. The diffusion and segregation of Ni, Nb and Ti elements underly the transformation mechanism between Laves, δ, γ’ and γ’’ phases during precipitation. Homogenization on FGMs not only eliminates the heterogeneity inherited from the AM process, but also provides a practical way to smoothen the gradient on composition and microstructure for the eventual good gradient properties. It has a direct influence on the following precipitation behaviors in the FGM, which highly relies on the diffusion degree of the elements in the matrix and grain boundaries. The high-throughput thermodynamic modeling and kinetic modeling were exploited to evaluate the experimental microstructure and address computational uncertainty using different thermodynamic conditions and databases, which enables an accelerated design through local tailoring of process-structure-property relationships to develop new functional materials.

The superharmonic imaging of tissue has the potential for high spatial and contrast resolutions, compared to the fundamental and second harmonic imaging. For this technique, the spectral bandwidth of an ultrasound transducer is divided for transmission of ultrasound and reception of its superharmonics (i.e., higher than the second harmonic). Due to the spectral division for the transmission and reception, transmitted ultrasound energy is not sufficient to induce superharmonics in media without using contrast agents, and it is difficult that a transducer has a -6-dB fractional bandwidth of higher than 100%. For the superharmonic imaging of tissue, thus, multi-frequency array transducers are the best choice if available; transmit and receive elements are separate and have different center frequencies. However, the construction of a multi-frequency transducer for intravascular ultrasound (IVUS) imaging is particularly demanding because of its small size of less than 1 mm. Here, we report a recently developed dual-element focused IVUS transducer for the third harmonic imaging of tissue, which consists of a 35-MHz element for ultrasound transmission and a 105-MHz element for third harmonic reception. For high quality third harmonic imaging, both elements were fabricated to have the same focus at 2.5 mm. The results of tissue mimicking phantom tests demonstrated that the third harmonic images produced by the developed transducer had higher spatial resolution and deeper imaging depth than the fundamental images.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

As shown in former papers, the nonadiabatic Heisenberg model presents a novel mechanism of Cooper pair formation generated by the strongly correlated atomic-like motion of the electrons in narrow, roughly half-filled "superconducting bands". These are energy bands represented by optimally localized spin-dependent Wannier functions adapted to the symmetry of the material under consideration. The formation of Cooper pairs is not the result of an attractive electron-electron interaction but can be described in terms of quantum mechanical constraining forces constraining the electrons to form Cooper pairs. There is theoretical and experimental evidence that only this nonadiabatic mechanism operating in superconducting bands may produce eigenstates in which the electrons form Cooper pairs. These constraining forces stabilize the Cooper pairs in any superconductor, whether conventional or unconventional. Here we report evidence that also the experimentally found superconducting state in bismuth at ambient as well as at high pressure is connected with a narrow, roughly half-filled superconducting band in the respective band structure. This observation corroborates once more the significance of constraining forces in the theory of superconductivity.

A novel method based on a hybrid incremental modeling approach has been designed and applied to imbalance detection in ultra-high precision rotating machines. The model is obtained by a two-step iterative process that combines an overall model (least-squares fitting) with a local model (fuzzy k-nearest-neighbour) to take advantage of their complementary capacities. Three normalization strategies of evaluating the effect on accuracy are analyzed. A comparative study demonstrates that the hybrid incremental model provides better error-based performance indices for detecting imbalance than a nonlinear regression model and an adaptive neural-fuzzy inference system model. The suitability of Mahanolobis normalization for hybrid incremental modeling is also demonstrated in this case study. The proposed strategy for imbalance detection is simple, fast, and non-intrusive, reducing the deterioration in the performance of ultra-high precision rotating machines due to vibrations.

Red mud is a hazardous waste of alumina industry that contains high amounts of iron, aluminum, titanium and REEs. One of the promising methods for the extraction of iron from red mud is car-bothermic reduction with the addition of sodium salts. This research focuses on the process of hy-drochloric high-pressure acid leaching using 10–20% HCl of two samples of non-magnetic tailings obtained by 60-minute carbothermic roasting of red mud at 1300 °C and the mixture of 84.6 wt. % of red mud and 15.4 wt. % Na2SO4 at 1150 °C, respectively, with subsequent magnetic separation of metallic iron. An influence of temperature, leaching duration, solid-to-liquid-ratio and acid con-centration on dissolution behavior of Al, Ti, Mg, Ca, Si, Fe, Na, La, Ce, Pr, Nd, Sc, Zr were studied. Based on the investigation of the obtained residues, mechanism of passing of valuable elements into the solution was proposed. It has shown that 90% Al, 91% Sc and above 80% of other REEs can be dissolved under optimal conditions; Ti can be extracted into the solution or the residue depending on the leaching temperature and acid concentration. Based on the research results, novel flowsheets for red mud treatment were developed.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

The aim of this study was to investigate the role of DNA methylation in the regulation of in vitro and in vivo cartilage formation. Based on the data of an RNA chip-assay performed on chondrifying BMP2-overexpressing C3H10T1/2 cells, the relative expression of Tet1 (tet methylcytosine dioxygenase 1), Dnmt3a (DNA methyltransferase 3) and Ogt (O-linked N-acetylglucosamine transferase) genes was examined with RT-qPCR in mouse cell-line based and primary micromass cultures. RNA probes for in situ hybridization were used on frozen sections of 15-day-old mouse embryos. DNA methylation was inhibited with 5-azacytidine during culturing. We found very strong but gradually decreasing expression of Tet1 throughout the entire course of in vitro cartilage differentiation along with strong signals in the cartilaginous embryonic skeleton. Dnmt3a and Ogt expressions did not show significant changes with RT-qPCR and gave weak in situ hybridization signals. Inhibition of DNA methylation applied during early stages of differentiation reduced cartilage-specific gene expression and cartilage formation. In contrast, it had stimulatory effect when added to differentiated chondrocytes. Our results indicate that the DNA demethylation-inducing Tet1 is a significant epigenetic factor of chondrogenesis, and inhibition of DNA methylation exerts distinct effects in different phases of in vitro cartilage formation.

A critical discussion on the computation of the dispersion diagram in periodic one-dimensional guiding structures is carried out. In particular, an analysis is presented of the pros and cons of combined methods that make use of full-wave simulations done with commercial software packages with further analytical post-processing based on simplifications brought by an equivalent circuit model of the structure. Some of the most common methods reported in the literature are reviewed and their advantanges and limitations highlighted. Our discussion is complemented with several selected numerical examples in order to discuss the most relevant aspects that a potential user of these methods should be aware of. Special attention is paid to the relevant role played by the high-order coupling between the two halves of a symmetric unit cell of the periodic structure.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

Alternative fuels available at low cost, friendly to natural environments and meet the energy needs and demands, have witnessed a growing demand and use today. Ethanol is an attractive renewable energy source with a high content of oxygen. Ethanol can be produced through ethanolisis, however for this work direct blending of conventional diesel, waste plastic pyrolysis oil and ethanol with commercial fuel improver CI-0808 purchased from Innospec company was attempted. The primary purpose of adding a cetane improver was to improve the combustion characteristics of the blends by at least 1- 3 ignition quality points. Five mixing ratios were chosen in the following order, 50:25:25, 60: 20:20, 70: 15:15, 80: 10:10 and 90: 5:5 for Waste Plastic Pyrolysis Oil (WPPO), ethanol and conventional diesel (CD) respectively. However, for the fuel additive mixing ratio the total volume percentage was considered and the ratio put at 0.01% of the total quantity of blended fuel. In this work WPPO, diesel blends and fuel additives improvers were used as alternative fuel. This was to evaluate their performance and emission characteristics in a stationary single cylinder water cooled experimental diesel engine. The CI-0808 was added due to its potential power to reduce emissions of CO, UHC, NO_X, PM and improved engine performance. The results obtained were compared carefully to ASTM standards and discussed using graph curves figures and tabulated values. The conclusion was that ethanol and WPPO blends can be used in diesel engines as alternative fuel without modification. Used in combination with cetane improvers the emissions reduce significantly and performance improved equalling that of conventional diesel fuel.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

In this paper we describe a nonparametric maximum likelihood (NPML) method for estimating multivariate mixing distributions. Given $N$ independent observations, convexity theory shows that the NPML estimator is discrete with at most $N$ support points. The original infinite NPML problem then becomes the finite dimensional problem of finding the location and probability of the support points. The probability of the support points is found by a Primal-Dual Interior-Point method; the location of the support points is found by an Adaptive Grid method. Our method is able to handle high-dimensional and complex multivariate mixture models.An important application is discussed for the problem of population pharmacokinetics and a non-trivial example is treated.Our algorithm has been successfully applied in hundreds of published pharmacometric studies. In addition to population pharmacokinetics, this research also applies to empirical Bayes estimation and many other areas of applied mathematics.

Eating Disorders (ED) constitute a serious public health issue affecting predominantly women and appearing typically in adolescence or early adulthood. EDs are extremely difficult to treat as these disorders are ego-syntonic and many patients do not seek treatment. It is vital to focus on the development of successful early-intervention programs for individuals presenting at-risk and are on a trajectory towards developing EDs. This study is a randomized controlled trial evalu-ating an innovative digital gamified Acceptance and Commitment early-intervention program (AcceptME) for young females showing signs and symptoms of an ED and at high-risk for an ED. Participants (N=92; Mage=15.30 years, SD=2.15) received either AcceptME (N=62) or a waitlist control (N=30). Analyses indicated that the AcceptME program effectively reduced weight and shape concerns, with large effects when compared to waitlist controls. Most participants scored below the at-risk cut-off (WCS score<52) in the AcceptME at end-of-intervention (57.1%) com-pared to controls (7.1%) with odds of falling into the at-risk group being 14.5 times higher for participants in the control group. At follow-up, 72% of completers reported scores below the at-risk cut-off in the AcceptME group. The intervention also resulted in a decrease in ED symp-tomatology and increased body image flexibility. Overall, results suggest that the AcceptME program holds promise for early-intervention of young women at-risk for developing an ED.

In the Quaternary paleosciences, the rationale behind analogical inference presupposes that former natural changes can be explained by causes operating now, although their intensity and rates can vary through time. In this paper we synthesise synthetize the results of different modern analog studies and discuss their value to obtain the best inferences from high resolution past records. This synthesis is based on the following: 1) The monthly monitoring of calcite precipitation reveals a strong connection with primary producers and between-years variability; this precipitation produces a seasonal signal with imprint on varve formation. 2) Clear pollen sedimentation peaks occur in spring/summer and fall/winter that coincide with temperature, precipitation, relative humidity and winds; this pattern converges with the two-layer coupled varves representing the same seasonality. 3) We assess the lake’s contemporary oxygenation dynamics over a three- year period; a combination of sedimentary REDOX proxies revealed different scenarios of oxic/anoxic shifts since 1500 CE. 4) We investigate presence of seasonality in the production/distribution of glycerol dialkyl glycerol tetraethers and derived temperature estimates in soils and particulate matter. Branched glycerol dialkyl glycerol tetraethers signatures and some derived temperature estimates proxies appear to mainly depend on the non-seasonal shifts in soil properties. 5) Currently we examine relationships and similarities between extant phytoplankton and derived pigments in water and traps, and their correspondence with subfossil pigments; some preliminary results are presented here.Keywords: high resolution, endogenic varves, calcite precipitation, pollen sedimentation, meromixis, freshwater glycerol dialkyl tetraether, subfossil pigments, long-term ecology.

Backward electromagnetic waves are extraordinary waves with contra-directed phase velocity and energy flux. Unusual properties of the coherent nonlinear optical coupling of the phase-matched ordinary and backward electromagnetic waves with contra-directed energy fluxes are described which enable greatly-enhanced frequency and propagation direction conversion, parametrical amplification, as well as control of shape of the light pulses. Extraordinary transient processes that emerge in such metamaterials in pulsed regimes are described. The results of the numerical simulation of particular plasmonic metamaterials with hyperbolic dispersion are presented, which prove the possibility to match phases of such coupled guided ordinary and backward electromagnetic waves. Particular properties of the outlined processes in the proposed metamaterial are demonstrated through numerical simulations. Potential applications include ultra-miniature amplifiers, frequency changing reflectors, modulators, pulse shapers, and remotely actuated sensors.

Plant geneticists and breeders have used marker technology since the 1980s in quantitative trait locus (QTL) identification. Marker-assisted selection is effective for large-effect QTL but has been challenging to use with quantitative traits controlled by multiple minor effect alleles. Therefore, genomic selection (GS) was proposed to estimate all markers simultaneously, thereby capturing all their effects. However, breeding programs are still struggling to identify the best strategy to implement it into their programs. Traditional breeding programs need to be optimized to implement GS effectively. This review explores the optimization of breeding programs for variety release based on aspects of the breeder’s equation. Optimizations include reorganizing field designs, training populations, increasing the number of lines evaluated, and leveraging the large amount of genomic and phenotypic data collected across different growing seasons and environments to increase heritability estimates, selection intensity, and selection accuracy. Breeding programs can leverage their phenotypic and genotypic data to maximize genetic gain and selection accuracy through GS methods utilizing multi-trait and, multi-environment models, high-throughput phenotyping, and deep learning approaches. Overall, this review describes various methods that plant breeders can utilize to increase genetic gains and effectively implement GS in breeding .

Fibrillin (FBN) is a plastid lipid-associated protein found in photosynthetic organisms from cyanobacteria to plants. In this study, 10 CsaFBN genes were identified in genomic DNA sequences of cucumber (Chinese long and Gy14) through database searches using the conserved domain of FBN and the 14 FBN genes of Arabidopsis. Phylogenetic analysis of CsaFBN protein sequences showed that there was no counterpart of Arabidopsis and rice FBN5 in the cucumber genome. FBN5 is essential for growth in Arabidopsis and rice; its absence in cucumber may be because of incomplete genome sequences or that another FBN carries out its functions. Among the 10 CsaFBN genes, CsaFBN1 and CsaFBN9 were the most divergent in terms of nucleotide sequences. Most of the CsaFBN genes were expressed in the leaf, stem, and fruit. CsaFBN4 showed the highest mRNA expression levels in various tissues, followed by CsaFBN6, CsaFBN1, and CsaFBN9. High-light stress combined with low temperature decreased photosynthetic efficiency and highly induced transcript levels of CsaFBN1, CsaFBN6, and CsaFBN11, which decreased after 24 h treatment. Transcript levels of the other seven genes were changed only slightly. This result suggests that CsaFBN1, CsaFBN6, and CsaFBN11 may be involved in photoprotection under high-light conditions at low temperature.

Wildland fires are responsible for large socio-economic impacts. Fires affect the environment, damage structures, threaten lives, cause health issues, and involve large suppression costs. These impacts can be mitigated via accurate fire spread forecast to inform the incident management team. We show that a fire forecast system based on a numerical weather prediction (NWP) model coupled with a wildland fire behavior model can provide this forecast. This is illustrated with the Chimney Tops II wildland fire responsible for large socio-economic impacts. The system is run at high horizontal resolution (111 m) over the region affected by the fire to provide a fine representation of the terrain and fuel heterogeneities and explicitly resolve atmospheric turbulence. Our findings suggest that one can use the high spatial resolution winds, fire spread and smoke forecast to minimize the adverse impacts of wildland fires.

(1) Background: High blood pressure is one of the symptoms of stroke, the Self Care Deficit theory by Dorothea Orem focuses on a person's ability to care for himself independently so that the ability to maintain his health and well-being is achieved. There are currently 600 million hypertensive patients worldwide, of which 3 million die every year. Uncontrolled high blood pressure can lead to a 7-fold increase in the chances of stroke. The existence of this condition can be minimized in patients through several innovative interventions, one of which is foot massage. This study aims to determine the effectiveness of stretching and foot massage with lavender oil in stabilizing high blood pressure in stroke patients.(2) Methods: The method used in this research is descriptive. The subjects of this case study were selected according to the inclusion and exclusion criteria of the journal Evidence-Based. Subjects included intervention patients and control patients. Foot massage therapy with lavender oil is done 2 times a day for 10-15 minutes using the effleurage technique after showering in the morning and evening. Stretching is done 2 times a day every 10-15 minutes.(3) Results: The results of the analysis showed that there was a change in blood pressure after the application of stretching and foot massage with lavender oil. From the initial examination, the results showed that the blood pressure of 170/100 mmHg decreased to 140/90 mmHg and the pain scale decreased from 4 to 0.

Lipophilicity can be measured with different methods, such as Shake-Flask or liquid chromatography. HPLC presents the advantage of overcoming solubility issues and therefore extending the range of lipophilicity to high values. A specific HPLC method, called ELogD, had been developed 20 years ago on a C₁₆-amide stationary phase, enhancing hydrophobic and hydrogen bond interactions to mimic octanol-water partition. The emergence of novel stationary phases added to the need for a less complex mobile phase has led to the development of a new HPLC assay called alphaLogD, applicable to neutral and basic compounds at pH 7.4, that combines superficially porous particles, a high number of equilibriums between solutes and stationary phase, and results in a lower number of isocratic methods to determine the logk’_w at a higher throughput. Statistical studies have been run to successfully evaluate the alphaLogD method compared to the Shake-Flask method and to allow this lipophilicity measurement into the so-called Beyond-Rule-of-5-molecules space.

A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

Evaluation of the effects of a high-frequency acceleration (HFA) device on patient pain response to orthodontic forces. A multi-centered trial investigating pain sensitivity to orthodontic forces on 75 subjects at 4 study centers. Subjects underwent clear aligner treatment, with or without adjunctive HFA and documented their pain intensity using the validated NRS10 numeric rating scale. In-Office and At-Home ratings were measured separately for each subject for immediate and extended effect evaluations. Use of HFA devices in conjunction with clear aligner orthodontic treatment demonstrated significant reduction in subjects’ recorded pain ratings vs controls within 5 minutes of aligner exchange, (p = 0.006) and significant reduction in recorded pain ratings vs controls over a 7-day period following aligner exchange (p = 0.018). A 99.6% daily compliance rate with at home use of the HFA device was recorded for all subjects in the study. HFA significantly reduces pain attributed to orthodontic force. HFA delivers clinically significant immediate pain relief, and clinically significant extended pain relief over the 7 days following adjustment.

This review discusses a broad range of recent advances (2013-2017) of chemical imaging using electrochemical methods, with a particular focus on techniques that have been applied to study cellular processes, or techniques that show promise for use in this field in the future. Non-scanning techniques such as microelectrode arrays (MEAs) offer high time-resolution (< 10 ms) imaging, however at reduced spatial resolution. In contrast, scanning electrochemical probe microscopies (SEPMs) offer higher spatial resolution (as low as a few nm per pixel) imaging, with images collected typically over many minutes. Recent significant research efforts to improve the spatial resolution of SEPMs using nanoscale probes, and to improve the temporal resolution using fast scanning have resulted in movie (multiple frame) imaging with frame rates as low as a few seconds per image. Many SEPM techniques lack chemical specificity or have poor selectivity (defined by the choice of applied potential for redox-active species). This can be improved using multifunctional probes, ion-selective electrodes and tip-integrated biosensors, although additional effort may be required to preserve sensor performance after miniaturization of these probes. We discuss advances to the field of electrochemical imaging, and technological developments which are anticipated to extend the range of processes that can be studied. This includes imaging cellular processes with increased sensor selectivity and at much improved spatiotemporal resolution than has been previously customary.

This paper proposes a forecast-centric adaptive learning model that engages with the past studies on the order book and high-frequency data, with applications to hypothesis testing. In line with the past literature, we produce brackets of summaries of statistics from the high-frequency bid and ask data in the CSI 300 Index Futures market and aim to forecast the one-step-ahead prices. Traditional time series issues, e.g. ARIMA order selection, stationarity, together with potential financial applications are covered in the exploratory data analysis, which pave paths to the adaptive learning model. By designing and running the learning model, we found it to perform well compared to the top fixed models, and some could improve the forecasting accuracy by being more stable and resilient to non-stationarity. Applications to hypothesis testing are shown with a rolling window, and further potential applications to finance and statistics are outlined.

The study describes the acute and delayed time course of recovery following the CrossFit® Benchmark Workout Karen. Eight trained men (28.4±6.4 years; 1RM back squat 139.1±26.0 kg) undertook the Karen protocol. The protocol consists of 150 Wall Balls, aiming to hit a target 3 meters high. Countermovement jump height (CMJ), creatine kinase (CK), and perceived recovery status scale (PRS) (general, lower and upper limbs) were assessed pre, post-0h, 24h, 48h and 72h after the session. The CK concentration 24h after was higher than pre-exercise (338.4 U/L vs. 143.3 U/L; effect size: 0.74; p≤0.05). At 48h and 72h following exercise, CK concentration had returned to baseline levels. The PRS general and of the lower limbs were lower in the 24-hours post-exercise compared to pre-exercise (PRS general: 4.7 ±1.5 and 7.9 ±1.7 mmol/L; and PRS of the lower limbs: 4.0 ±2.5 and 7.9 ±0.8, respectively). The PRS general, lower, and upper limbs were reduced at 48-post exercise compared to 72-hours post-exercise scores. Our findings provide insights into the fatigue profile and recovery in acute CrossFit® and can be useful to coaches effectively design the daily session.

Bioactive peptides are related to the prevention and treatment of many diseases. GPETAFLR is an octapeptide which was isolated from lupine (Lupinus angustifolius L.) and showed anti-inflammatory properties. The aim of this study was to evaluate the potential activity of GPETAFLR to prevent non-alcoholic fatty liver disease (NAFLD) in high-fat diet (HFD)-induced obese mice. C57BL/6J mice were fed a standard diet or an HFD. Two of the groups fed the HFD diet were treated with GPETAFLR in their drinking water at 0,5 mg/kg/d or 1 mg/kg/d. To determine the ability of GPETAFLR to improve the onset and progression of NAFLD, histological studies, hepatic enzyme profile, inflammatory cytokine and lipid metabolism-related genes and proteins were analyzed. Our results suggest that HFD-induced inflammatory metabolic disorders were alleviated by treatment with GPETAFLR. In conclusion, dietary lupine consumption could repair HFD-induced hepatic damage, possibly via modifications in the liver’s lipid signalling pathways.

This article reports a novel and efficient method to synthesize graphene by thermal decomposition process. In this method, silicon carbide (SiC) thin films grown on Si(100) wafers with an AlN buffer layer were used as substrates. A CO₂ laser beam heating without vacuum or controlled atmosphere was applied for SiC thermal decomposition. The physical, chemical, morphological, and electrical properties of the laser-produced graphene were investigated for different laser energy densities. The results demonstrate that graphene was produced in form of small islands with quality, density and properties depending on the applied laser energy density. Furthermore, the produced graphene exhibits a sheet resistance characteristic similar to graphene grown on mono-crystalline SiC wafer, which indicates its potential for electronic device applications.

We introduce firm solar forecasts as a strategy to operate optimally overbuilt solar power plants in conjunction with optimally sized storage systems so as to make up for any power prediction errors, hence entirely remove load balancing uncertainty emanating from grid-connected solar fleets. A central part of this strategy is plant overbuilding that we term implicit storage. We show that strategy, while economically justifiable on its own account, is an effective entry step to least-cost ultra-high solar penetration where firm power generation will be a prerequisite. We demonstrate that in absence of an implicit storage strategy, ultra-high solar penetration would be vastly more expensive. Using the New York Independent System Operator (NYISO) as a case study, we determine current and future cost of firm forecasts for a comprehensive set of scenarios in each ISO electrical region, comparing centralized vs. decentralized production and assessing load flexibility’s impact. We simulate the growth of the strategy from firm forecast to firm power generation. We conclude that ultra-high solar penetration enabled by the present strategy, whereby solar would firmly supply the entire NYISO load, could be achieved locally at electricity production costs comparable to current NYISO wholesale market prices.

The effects of psychological pressure on perceiving the height of a jump bar just before starting a high jump run was investigated. University students (N = 14) training for a high jump event performed 15 trials (3 practice, 6 pressure, and 6 non-pressure) in counterbalanced order in their daily practice environment. The height of the bar was judged as significantly higher on pressure trials compared to non-pressure trials. A regression analysis indicated that participants who reported increased subjective perceived pressure tended to judge the bar to be higher. There was no significant difference between pressure and non-pressure trials for the performance index, defined as the success rate. This study provides the first evidence that environmental perceptions prior to executing a motor task under pressure may make performance of the task appear to be more difficult.

Root research on field grown crops is hindered by the difficulty of estimating root biomass in soil. Root washing, the current standard method is laborious and expensive. Biochemical methods to quantify root biomass in soil, targeting species-specific DNA, have potential as a more efficient assay. We combined an efficient DNA extraction method, designed specifically to extract DNA from soil, with well-established quantitative PCR methods to estimate the root biomass of twenty-two wheat varieties grown in field trials over two seasons. We also developed an assay for estimating root biomass for black-grass, a common weed of wheat cultivation. Two robust qPCR assays were developed to estimate the quantity of plant root DNA in soil samples, one specific to wheat and barley, and a second specific to black-grass. The DNA qPCR method was comparable, with high correlations, with the results of root washing from soil cores taken from winter wheat field trials. The DNA qPCR assay showed both variety and depth as significant factors in the distribution of root biomass in replicated field trials. The results suggest that these DNA qPCR assays are a useful, high throughput tool for investigating the genetic basis of wheat root biomass distribution in field grown crops, and the impact of black-grass root systems on crop production.

Background: Multifunctional nanoparticles are known for their wide range of biomedical applications. Controlling the magnetic properties of these nanoparticles is imperative for various applications, including therapeutic angiogenesis. The study was performed to evaluate the magnetic properties and their control mechanisms by the external magnetic field. Methods: A 100nm magnetic nanoparticle was placed in the magnetic field, and parametrically the magnet field strength and distance was evaluated. Various models of magnetic strength and disposition were evaluated. Magnetic flux density, force/weight, and magnetic gradient strength were the parameters evaluated in electromagnetic computational software. Results: The seven-coil method with three centrally placed coils as Halbach array, and each coil with a flux density of 7 Tesla, and with a coil dimension of 20cmx20cm (square model) of each coil showed a good magnetic strength and force/weight parameters in a distance of 15cm from the centrally placed coil. The particles were then evaluated for their motion characteristics in saline. It showed good displacement and acceleration properties. After that, the particles were theoretically assessed in a similar mathematical model after parametrically correcting the drag force. After application of high drag forces, the particles showed adequate motion characteristics. When the particle size was reduced further, the motion characteristics were preserved even with high drag forces. Conclusion: There is potential for a novel method of controlling multifunctional magnetic nanoparticles using high magnetic fields. Further studies are required to evaluate the motion characteristics of these particles in-vivo and invitro.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

We present an overview over eight brightly luminescent Cu(I) dimers of the type Cu2X2(PN)3 with X = Cl, Br, I and P^N = 2-diphenylphosphino-pyridine (Ph2Ppy), 2-diphenylphosphino-pyrimidine (Ph2Ppym), 1-diphenylphosphino-isoquinoline (Ph2Piqn) including three new crystal structures (Cu2Br2(Ph2Ppy)3, 1-Br, Cu2I2(Ph2Ppym)3, 2-I, and Cu2I2(Ph2Piqn)3, 3-I). However, we mainly focus on their photo-luminescence properties. All compounds exhibit combined thermally activated delayed fluorescence (TADF) and phosphorescence at ambient temperature. Emission color, decay time, and quantum yield varies over large ranges. For deeper characterization, we select Cu2I2(Ph2Ppy)3, 1-I, showing a quantum yield of 81 %. DFT and SOC-TDDFT calculations provide insight into the electronic structures of the singlet S1 and triplet T1 states. Both stem from metal+iodide-to-ligand charge transfer transitions. Evaluation of the emission decay dynamics, measured from 1.2 ≤ T ≤ 300 K, gives ∆E(S1-T1) = 380 cm-1 (47 meV), a transition rate of k(S1→S0) = 2.25×106 s-1 (445 ns), T1 zero-field splittings, transition rates from the triplet substates, and spin-lattice relaxation times. We also discuss the interplay of S1-TADF and T1-phosphorescence. The combined emission paths shorten the overall decay time. For OLED applications, utilization of both singlet and triplet harvesting can be highly favorable for improvement of the device performance.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

Geologists employ high-spatial-resolution (HR) remote sensing (RS) data for many diverse applications as they effectively reflect detailed geological information, enabling high-quality and efficient geological surveys. Applications of HR RS data to geological and related fields have grown recently. By analyzing these applications, we can better understand the results of previous studies and more effectively use the latest data and methods to efficiently extract key geological information. HR optical remote sensing data are widely used in geological hazard assessment, seismic monitoring, mineral exploitation, glacier monitoring, and mineral information extraction due to high accuracy and clear object features. Compared with optical satellite images, synthetic-aperture radar (SAR) images are stereoscopic and exhibit clear relief, strong performance, and good detection of terrain, landforms, and other information. SAR images have been applied to seismic mechanism research, volcanic monitoring, topographic deformation, and fault analysis. Furthermore, a multi-standard maturity analysis of the geological applications of HR images using literature from the Science Citation Index reveals that optical remote sensing data are superior to radar data for mining, geological disaster, lithologic, and volcanic applications, but inferior for earthquake, glacial, and fault applications. Therefore, geological remote sensing research needs to be truly multidisciplinary or interdisciplinary, ensuring more detailed and efficient surveys through cross-linking with other disciplines. Moreover, the recent application of deep learning technology to remote sensing data extraction has improved automatic processing and data analysis capabilities.

Patch antennas are compact, less complex, planar structures and therefore, widely used in small satellite missions for telecommand, data link, and intersatellite link, particularly in S- band and X- band. Improved performance of these patch antennas in terms of gain and compactness will di-rectly affect the communication efficiency of small satellite missions. Especially the coming IoT (Internet of Things) constellations require high gain and efficient antenna arrays. An optimization of single patch antenna elements is an important cornerstone for the missions. Therefore, the ef-fects of various antenna enhancement techniques, such as slotted ground plane, resistor and ca-pacitor integration, parasitic patch elements, are analyzed. These techniques were applied on a rectangular patch antenna with parameter variation to identify the optimal performances with respect to bandwidth, operating frequency, gain, polarization, and power flow. Finally, the techniques were combined to obtain an optimized antenna in terms of gain and compactness. The results were compared to a slotted reference antenna. For the scenario of a 2.4 GHz patch antenna, a gain optimization of 27 % (from 7.09 to 8.14 dBi) or size reduction of 52 % (from 96.04 to 46.2 cm²) could be achieved. Overall, our study revealed an effective way to increase the patch antenna performance, which can directly contribute to more efficient communication links and design of antenna arrays.

Analyses of the Hubble diagrams are presented for SN1a supernovae and gamma ray bursts in the redshift ranges z = 0.01–1.3 and 0.034–8.1, respectively. Data are presented on the typical z/μ scale and also on the less common yet increasingly sensitive photon flight time t/(z+1) scale. The primary conclusion is that on the basis of the presently accessible data in the redshift range z = 0.01–8.1, the slope of the Hubble diagram is, or is extremely close to, exponential.

In bioprocess development, the host and the genetic construct for a new biomanufacturing process are selected in the early developmental stages. This decision, made at the screening scale with very limited information about the performance of the selected cell factory in larger reactors, has a major influence on the performance of the final process. To overcome this, scaledown approaches are essential to run screenings that show the real cell factory performance at industrial like conditions. We present a fully automated robotic facility with 24 parallel mini-bioreactors that is operated by a model based adaptive input design framework for the characterization of clone libraries under scale-down conditions. The cultivation operation strategies are computed and continuously refined based on a macro-kinetic growth model that is continuously re-fitted to the available experimental data. The added value of the approach is demonstrated with 24 parallel fed-batch cultivations in a mini-bioreactor system with eight different Escherichia coli strains in triplicate. The 24 fed-batches ran under the desired conditions generating sufficient information to define the fastest growing strain in an environment with varying glucose concentrations similar to industrial scale bioreactors.

Lithium titanates are used in various applications, such as anode materials for lithium intercalation (Li4Ti5O12) or breeding materials in fusion reactors (Li2TiO3). Here, we report the formation of nano-crystalline lithium titanates by a mechanochemical approach and present a deeper insight into their structural characteristics by PXRD and solid-state NMR spectroscopy. The compounds were synthesized in a high energy planetary ball mill with varying milling parameters and different grinding tools. NaCl type Li2TiO3 (α-Li2TiO3) was formed by dry milling of lithium hydroxide with titania (rutile or anatase) and by a milling induced structure transformation of monoclinic β Li2TiO3 or spinel type Li4Ti5O12. Heating of mechanochemical prepared α Li2TiO3 induces a phase transformation to the monoclinic phase similar to hydrothermal reaction products, but a higher thermal stability was observed for the mechanochemical formed product. Microstructure and crystallographic structure were characterized by PXRD via Rietveld analysis. Detailed phase analysis shows the formation of the cubic phase from the various educts. A set of two lattice parameters for α Li2TiO3 was refined, depending on the presence of OH- during the milling process. An average crystallite size of less than 15 nm was observed for the mechanochemical generated products. The local Li environment detected by 6Li SPE MAS NMR revealed Li defects in the form of tetrahedral instead of octahedral site occupation. Subsequent adjustment of the structural model for Rietveld refinement leads to better fits, supporting this interpretation.

By combing continuum topology optimization (TO) method and lattice structure technique, a sandwich aircraft spoiler with a high stiffness-to-weight is designed. TO method is served to produce the shell of the aircraft spoiler and the lattice structure, used as cores, is employed to support the shell. TO problem is established as maximizing the stiffness of the structure with limited material volume. Density-based method is utilized to achieve a 0/1 solution. We then empirically replace the core of the aircraft spoiler by using 3D kagome lattice structure. Two different materials, i.e., aluminum alloy and titanium alloy, are synthetically applied to further reduce the weight and simultaneously improve the strength of the aircraft spoiler. Numerical simulations are conducted to show that the designed aircraft spoiler can meet the service environment with a reduction of its weight by approximately 80% when compared with that of the initial design model. Finally, we have fabricated the designed model with photosensitive resin by using 3D printing technique.

As novel materials for carbon capture, phase change solvents can separate into two immiscible phases during the CO2 capturing procedure under a certain temperature. The solvent systems can significantly decrease the energy consumption since the solvents can be regenerated by only heating the rich-CO2 phase. In this work, amino acid ionic liquids (AAILs) were synthesized using quaternary ammonium salts and amino acids as raw materials, and the aqueous solutions were prepared as novel liquid-solid phase change solvents. The results showed that the solvents had excellent CO2 absorption capacity, and the AAILs functionalized by glycine and tryptophan exhibited significant phase change properties. The mechanism of phase-change of the solvent were mainly due to the lower solubility of the product after reaction between AAILs and CO2. The solvent with tryptophan as anion could be regenerated by only heating the CO2-riched solid phase, which might significantly decrease energy consumption of regeneration. And the absorbent could be reused with the regenerated absorption ratio up to 79%. The solvent system has great potential in industrial application due to the easy operation process and efficient recycling ability.

The exact etiology of myopia remains elusive. The author proposes the particle property of photon in living tissue and the photon-electron theory in living tissue, if the frequency of the photon exceeds the threshold, the photon has enough energy to strike the electron away and forms a hole of a diameter in photon diameter scale in living tissue include the eye. Longer time of high-frequency electromagnetic radiation will cause more holes and a larger radius of holes. The visual light which passes through the radiated hole in the eye cannot be refracted on the macula, this is myopia symptom of blurred vision, shortening the distance of the eye and the object will include more visual light into cornea and lens, this is myopia another symptom of nearsightedness. The particle property of photon causes elongation of the eye and the macular holes.Blue light and X-ray are two kinds of high-frequency electromagnetic radiation which can shot holes in eye and cause myopia.

High-content fluorescence microscopy combines the efficiency of high-throughput techniques with the ability to extract quantitative information from biological systems. The planarian community has developed sensitive and robust assays for whole animals, yet cell based assays, despite their practical aspects, have not been explored to the same extent. Here we describe a modular collection of detailed protocols adapted for fixed planarian cells that enable multiplexed measurements of biomarkers in microwell plates. Methods include the detection of RNA transcripts by RNA fluorescent in situ hybridization combined with tyramide signal amplification using hapten-labeled riboprobes. In addition, immunocytochemical protocols for quantifying proliferating cells by the detection of phosphorylated histone H3 as well as 5-bromo-2'-deoxyuridine incorporation into the nuclear genome are described. The assays are compatible with planarians of virtually any size, as the tissue is disaggregated into a single cell suspension before fixation and staining. By sharing many reagents with established planarian whole mount staining protocols, preparation of samples for high-content microscopy adoption requires little additional investment. Recommendations for successful experimental workflows and common sources of errors are discussed.

Phenotypical screening is a widely used approach in drug discovery for the identification of small molecules with cellular activities. However, functional annotation of identified hits often poses a challenge. The development of small molecules with narrow or exclusive target selectivity such as chemical probes and chemogenomic (CG) libraries, greatly diminishes this challenge, but non-specific effects caused by compound toxicity or interference with basic cellular functions still poses a problem to associate phenotypic readouts with molecular targets. Hence, each compound should ideally be comprehensively characterized regarding its effects on general cell functions. Here, we report an optimized live-cell multiplexed assay that classifies cells based on nuclear morphology, presenting an excellent indicator for cellular responses such as early apoptosis and necrosis. This basic readout in combination with the detection of other general cell damaging activities of small molecules such as changes in cytoskeletal morphology, cell cycle and mitochondrial health provides a comprehensive time-dependent characterization of the effect of small molecules on cellular health in a single experiment. The developed high-content assay offers multi-dimensional comprehensive characterization that can be used to delineate generic effects regarding cell functions and cell viability, allowing an assessment of compound suitability for subsequent detailed phenotypic and mechanistic studies.

Miscanthus holds a great potential in the frame of the bioeconomy and yield prediction can help improving Miscanthus logistic supply chain. Breeding programs in several countries are attempting to produce high-yielding Miscanthus hybrids better adapted to different climates and end-uses. Multispectral images acquired from unmanned aerial vehicles (UAVs) in Italy and in the UK in 2021 and 2022 were used to investigate the feasibility of high-throughput phenotyping (HTP) of novel Miscanthus hybrids for yield prediction and crop traits estimation. An intercalibration procedure was performed using simulated data from the PROSAIL model to link vegetation indices (VIs) derived from two different multispectral sensors. Random forest algorithm estimated with good accuracy yield traits (light interception, plant height, green leaf biomass and standing biomass) using VIs time series and predicted yield using peak descriptor derived from VIs time series with 2.3 Mg DM ha-1 of RMSE. The study demonstrates the potential of UAVs multispectral in HTP applications and in yield prediction for providing important information needed to increase sustainable biomass production.

With the ever-increasing rate, obesity has become an epidemiological problem throughout the globe comprising about 39% of the world population as of now. Among several reasons, disruption of the gut microbial ecosystem might contribute to the pathogenesis of metabolic disorders, including obesity, metabolic syndrome, type 2 diabetes, and other associated comorbidities. Though the mechanisms related to dysbiosis are unclear, diet might play a modulating role where different dietary approaches manipulate microbial richness and abundance as well as stability. For instance, shifting of Firmicutes and Bacteroidetes ratio in the gut might have a role in association with the dietary approaches and ingestion duration. Along with altered gut microbial composition, microbial metabolites such as short-chain fatty acids (SCFA) after ingestion of non-digestible dietary starches may have an impact on host metabolism by regulating lipogenesis, gluconeogenesis, and inflammation with potential associations to health and obesity. The dietary approaches like carbohydrates, fibre, protein, and/or fat diet at various arrangements can make a shift in the composition of gut microbiota if introduced for a short period. However, the unique pattern of the gut microbes usually remains the same along with the longer period of habitual diet. Though the short-term dietary intervention or circadian rhythm influences a transient change in gut microbes, other than habitual diet, the understanding related to long-term dietary change-induced permanent alterations is minimum. Alternatively, the usage of prebiotics, probiotics as well as postbiotics could be beneficial to overcome dysbiosis. This review highlights the current knowledge and the interaction between the human intestinal microbiota and diet as a modifying factor, in obesity allowing the scientists to uncover novel targets and tools to use as customized therapy.

The aim of this study is to investigate, by means of experimental measurements and full-wave simulations, the dominant factors for the very high-resolution (VHR) radar image speckles from exponential correlated rough surfaces. A Ka-band radar system was used to collect the return signal from such a surface sample fabricated by 3D printing, and that signal was further processed into images at different resolution scales, where the image samples were obtained by horizontally turning around the surface sample. To cross-validate the results and to further discuss the VHR speckle properties, full wave simulations by full 3D Finite Difference Time Domain (FDTD) method were conducted with 1600 realizations for the speckle analysis. At the considered very high resolution, speckle statistics show divergence from the fully developed Rayleigh distribution. The factors that impact on the high-resolution speckle properties from exponential correlated rough surface, are analyzed in views of the equivalent number of scatterers theory and scattering scales, respectively. From the data results and extended discussions, it is evident that both of the above factors matter for VHR speckle of backscattering, from the exponential correlated rough surface as a good representative for the ground surface.

This paper presents an experimental scenario aimed at bridging the gap between the cities we have and the cities we need, not only in the 21^st century but also beyond, using the integrated tools of development control and holistic land development model to achieve a planner-led vision of city sustainability. Due to scathing criticisms against the development control system, the paper contends that planners as development approving officers and public interest specialists are better positioned than allied professionals to increase city sustainability through a holistic development process that benefits from the concept of strong sustainability posited by ecological economists. The paper adopts a seven-stage, 56-cell land development matrix (model) to simulate the development of the typical high-rise residential condominium in Ontario, supported with secondary data and the author’s ground experience as a planner and realtor with condominium customer service experience across Toronto and Mississauga cities between 2008 and 2017. Findings reveal that planners can seize the opportunity of being leaders of the development team to synergize the risks and value creation in land development that are key drivers of strong sustainability. The paper suggests some policy implications for averting disasters like fire hazards and terror attacks in high-rise residential buildings.

Floods are one of the most wide-spread, frequent, and devastating natural disasters that continue to increase in frequency and intensity. Remote sensing, specifically synthetic aperture radar (SAR), has been widely used to detect surface water inundation to provide retrospective and near-real time (NRT) information due to its high-spatial resolution, self-illumination, and low atmospheric attenuation. However, the efficacy of flood inundation mapping with SAR is susceptible to reflections and scattering from a variety of factors including dense vegetation and urban areas. In this study, the topographic dataset height above nearest drainage (HAND) was investigated as a potential supplement to Sentinel-1A C-Band SAR along with supervised machine learning to improve the detection of inundation in heterogeneous areas. Three machine learning classifiers were trained on two sets of features SAR only (VV & VH) and VV, VH & HAND to map inundated areas. Three study sites along the Neuse River in North Carolina, USA during the record flood of Hurricane Matthew in October 2016 were selected. The binary classification analysis (inundated as positive vs. non-inundated as negative) revealed significant improvements when incorporating HAND in several metrics including classification accuracy (ACC) (+37.1%), true positive rate (TPR) (+51.2%), and negative predictive value (NPV) (+23.7%), A marginal improvement of +1.4% was seen for positive predictive value (PPV), but true negative rate (TNR) fell -15.1%. By incorporating HAND, a significant number of areas with high SAR backscatter but low HAND values were detected as inundated which increased true positives. This in turn also increased the false positives detected but to a lesser extent as evident in the metrics. This study demonstrates that HAND could be considered a valuable feature to enhance SAR flood inundation mapping especially in areas with heterogeneous land covers with dense vegetation that interfere with SAR.

A high-performance Lead-free Piezoelectric Energy Harvester (LPEH) based on a Ba0.85Ca0.15Ti0.90Zr0.10O3 + CuO 0.3 wt% (BCTZC0.3) composite was fabricated by sintering at 1450℃. The BCTZC0.3 composite, which has an enhanced high-energy-conversion constant (〖d_33×g〗_33), shows improved piezoelectric power-generation performance when compared with conventional piezoelectric energy harvesters. The BCTZC0.3-based LPEH produces instantaneous maximum power of 8.2 mW and an energy density of 107.9 mW/cm3 in a weak magnetic field of 250 μT. This energy harvester can be used to charge a capacitor and operate a wireless sensor network (WSN) system to provide temperature sensing and radio-frequency (RF) transmission in a 250 μT magnetic field. The proposed LPEH is a promising green-energy device for potentially self-powering WSN systems when applied.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

The cardioprotective effects of volatile anesthetics versus total intravenous anesthesia (TIVA) are controversial, especially in patients undergoing non-cardiac surgery. Using current generation high-sensitivity cardiac troponin (hs-cTn), we aimed to evaluate the effect of anesthetics on the occurrence of myocardial injury after non-cardiac surgery (MINS). From February 2010 to December 2016, 3555 patients without preoperative hs-cTn elevation underwent non-cardiac surgery under general anesthesia. Patients were grouped according to anesthetic agent; 659 patients were classified into a propofol-remifentanil total intravenous anesthesia (TIVA) group, and 2896 patients were classified into into a volatile group. To balance the use of remifentanil between groups, a balanced group (n=1622) was generated with patients who received remifentanil infusion in the volatile group, and two separate comparisons were performed (TIVA vs. volatile and TIVA vs. balanced). The primary outcome was occurrence of MINS, defined as rise of hs-cTn I ≥ 0.04 ng/mL within postoperative 48 hours. The secondary outcomes were 30-day mortality, postoperative acute kidney injury (AKI), and adverse events during hospital stay (mortality, type I myocardial infarction (MI), and new-onset arrhythmia). In propensity-matched analyses, the occurrence of MINS was lower in the TIVA group compared to the volatile group (OR 0.642; 95% CI 0.450-0.914; p = 0.014). However, after balancing the use of remifentanil, there was no difference between groups in the risk of MINS (OR 0.832; 95% CI 0.554-1.251; p-value = 0.377). There were no significant associations between the two groups in type 1 MI, new-onset atrial fibrillation, in-hospital and 30-day mortality before and after balancing the use of remifentanil. However, the incidence of postoperative AKI was lower in the TIVA group (OR 0.362; 95% CI 0.194-0.675; p-value = 0.001). After balancing the use of remifentanil, volatile anesthesia and TIVA showed comparable effects on MINS in patients undergoing non-cardiac surgery without preoperative myocardial injury. Further studies are needed on the benefit of remifentanil infusion.

Factors affecting the host-virus interaction must be understood for the effective application of bacteriophages to combat bacterial pathogens. Two novel E. coli phages, the T1-like siphophage LL5 and the rV5-like myophage LL12, were subjected to forward genetic screens against the Keio collection, a library of single non-essential gene deletions in E.coli str. BW25113. These genome-wide screens and subsequent experiments identified eight genes required for efficient propagation of phage LL5 and six genes required for propagation of LL12. The majority of the genes identified were involved in production of the phage receptors. E. coli mutants deficient in heptose II and the phosphoryl substituent of heptose I of the inner core lipopolysaccharide (LPS) were unable to propagate phage LL5, as were mutants deficient in the outer membrane protein TolC. Mutants lacking glucose I of the LPS outer core failed to propagate LL12. Two cytoplasmic chaperones, PpiB and SecB, were found to be required for efficient propagation of phage LL5 but not LL12. This approach may be useful for identifying phage receptors and required host factors in other phages, which would provide valuable information for their potential use as therapeutics and for phage engineering.

As time progresses and technology improves, biological data sets are continuously increasing in size. New methods and new implementations of existing methods are needed to keep pace with this increase. In this paper, we present a high performance computing(HPC)-capable implementation of Iterative Random Forest (iRF). This new implementation enables the explainable-AI eQTL analysis of SNP sets with over a million SNPs. Using this implementation we also present a new method, iRF Leave One Out Prediction (iRF-LOOP), for the creation of Predictive Expression Networks on the order of 40,000 genes or more. We compare the new implementation of iRF with the previous R version and analyze its time to completion on two of the world's fastest supercomputers Summit and Titan. We also show iRF-LOOP's ability to capture biologically significant results when creating Predictive Expression Networks. This new implementation of iRF will enable the analysis of biological data sets at scales that were previously not possible.

Plasma and serum are the most widely used blood-derived biofluids for metabolomics and lipidomics assays, but the isolation of these products from blood may introduce additional bias as indicated by the fact that many analytes that are present at high concentrations in blood cells cannot be measured and evaluated in those samples. Of particular concern, variable hemolysis during the pre-processing of blood products could compromise accurate and reproducible quantification. Compared with plasma or serum, whole blood may be a better alternative due to simplicity of processing. In this study, we provide a comprehensive method for quantification of the whole blood sphingolipidome and the concentrations were compared with those from plasma. Combining a single-phase extraction method with liquid-chromatography high resolution mass spectrometry (R=120, 000), assisted by alkaline hydrolysis, we were able to identify and simultaneously quantify more than 150 sphingolipids. Furthermore, most of sphingolipids remained stable after a freeze/thaw cycle. Whole blood contained a higher concentration of most sphingolipids than corresponding plasma. Moreover, individual variations in the levels of sphingolipids were lower for whole blood than plasma. These findings demonstrate that whole blood could be a better alternative to plasma, and potentially guide the evaluation of sphinglipidome for biomarker discovery.

The contextual and risk perception of climate change plays a critical role in an individual’s decision-making process. It could also help people to respond appropriately to the consequences of global climate change and eventually take necessary adaptation actions. However, the perceptions of climate change are often gendered and vary among men and women. Therefore, this study explores different perceptions of climate change and its local adaptation options among ultra-poor vulnerable women, particularly in highly vulnerable flood-prone regions of Bangladesh. The research followed an empirical research methodology to collect primary and secondary information using qualitative and quantitative research tools. The study findings reveal that climate change perceptions at the individual level are relatively low (63%). Still, they have been observing significant changes in various climatic variables over the past 30 years. Moreover, this study identified some major adaptation options such as plinth raising (100%), livestock rearing (100%), homestead gardening (82%), seasonal migration (82%), and using indigenous knowledge (69%), and so on to tackle the adverse impacts of climate change-induced extreme events including flooding at the local level. For implementing these adaptation measures, the respondents spent a significant amount of financial resources from individual sources in the study area. Structural Equation Modeling (SEM) is used in addition to the statistical analyses to understand any connections between the climate change perceptions and other variables associated with the community under study. The SEM result shows that climate change will be a long–term problem, which offers a strong predictor in this model, considering standardized regression weight β= 0.56. It means, despite inadequate knowledge on climate change of the respondent’s, climate change is occurring and becoming the worst factor limiting cultural, economic, and environmental development in the study area.

This study presents a novel technique utilizing high frequency vibration to shorten treatment time and preserve alveolar bone in challenging orthodontic cases treated with Invisalign® clear aligners. Four non-growing orthodontic patients (age range 14-47 years old) with Class II skeletal patterns (convex profiles with retrognathic mandibles) who sought correction of their crowded teeth and non-surgical correction of their convex profiles were included in this study. These patients were treated using Invisalign clear aligners together with high frequency vibration (HFV) devices (120 Hz) (VPro5™) that were used by all patients for five minutes per day during active orthodontic treatment. Vertical control and forward rotation of the mandible for each patient was achieved through pre-programming the Invisalign to produce posterior teeth intrusion. Successful forward rotation of the mandibles achieved in all patients led to improvement of their facial convex profiles (ANB improved 2.1 + 0.5 degrees; FMA improved 1.2 +1.1 degrees). Dental decompensation was achieved by lingual tipping of the lower incisors and palatal root torque of upper incisors. The use of HFV together with Invisalign facilitated achieving these results within a 12+6 month period. In addition, more bone labial to the lower incisors after their lingual movement was noted. In conclusion, the use of HFV concurrent with SmartTrack Invisalign aligners allowed complex tooth movement and forward projection without surgery in non-growing patients with skeletal Class II relationships. The clinical impact and implications of this case series is that the use of HFV facilitates complex orthodontic tooth movement including posterior teeth intrusion and incisor decompensation in addition to increased bone formation labial to lower incisors that may minimize future gum recession due to their labial inclination.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Background and objectives: Induction of labor (IOL) is an event that occurs in up to one-quarter of pregnancies; less is known about the outcomes and safety of IOL in obese pregnant woman; no data is available on misoprostol vaginal insert (MVI) IOL in high-risk pregnancy obese women. Objectives: (1) to evaluate the rate of successful IOL with 200 μg MVI in obese (Body Mass Index - BMI over 30 kg/m2) high-risk pregnant women: late-term pregnancy, hypertension or diabetes, compared to obese non-high-risk ones; (2) to evaluate the safety profile of MVI in high-risk pregnancy obese patients. Study design: We conducted a cross-sectional study in "Filantropia" Clinical Hospital, Bucharest, Romania, from June 2017 to September 2019 (28 months). From a total of 11,096 registered live births, IOL was performed in 206 obese patients; 74 obese high-risk pregnant patients matched the inclusion criteria; of these, 33.8% pregnancies (n=25) were late-term (41 – 41+6 weeks), 43.2% (n=32) had associated pathologies (hypertension and diabetes); labor induction was guided using a standardized protocol. We evaluated the maternal and gestational age, parity, fetal tachysystole, hyper-stimulation, initial cervical status, time from induction to delivery, drug side effects, mode of delivery, and neonatal outcomes. Results: (a) The overall successful labor induction rate, evaluated by the vaginal delivery rate, was 71.6% (n=53), spontaneously or instrumentally assisted; 28.4% (n=21) births were unsuccessful MVI IOL, converted into caesareans. (b) No significant differences were found regarding the maternal outcomes; in terms of perinatal outcomes of safety, four cases of high-risk pregnancies vaginally delivered were associated with neonatal intensive care unit (NICU) admissions and a one-minute Apgar score under seven (5.4%). Most cases with adverse effects of misoprostol have been managed conservatively, except for three emergency C-section cases. Conclusions: Misoprostol vaginal insert is a safe choice in IOL in obese high-risk pregnancies with good maternal and perinatal outcomes.

Different external stimuli are perceived by multiple sensor histidine kinases and transmitted by phosphorylation via the phosphotransfer protein Ypd1p in the multistep phosphorelay system of the high osmolarity glycerol signaling pathway of filamentous fungi. How the signal propagation takes place is still not known in detail, since multiple sensor histidine kinase genes in most filamentous fungi are coded in the genome, whereas only one gene for Ypd1 exists. That raises the hypothesis that various Ypd1 isoforms are produced from a single gene sequence, perhaps by alternative splicing, facilitating a higher variability in signal transduction. We found that the mRNA of MoYPD1 in the rice blast fungus Magnaporthe oryzae is subjected to an increased structural variation and amplified putative isoforms on a cDNA level. We then generated mutant strains overexpressing these isoforms, purified the products and present here one previously unknown MoYpd1 isoform on a proteome level. Alternative splicing was found to be a valid molecular mechanism to increase the signal diversity in eukaryotic multistep phosphorelay systems.

Currently the rapid growth of global economy has the competition among high-tech industries develop from regional to global, and the competition becomes fierce. In face of such fierce competition in global high-tech industry, it is realized that tangible assets could no longer be the differentiation basis, but intangible assets are regarded as the differentiation capital. An enterprise with sustainable innovation would dominate the world market and enhance the international competitiveness of domestic economy. When internal entrepreneurial culture is prevalent, an enterprise would naturally promote the innovation capability. Such a point of view also explains more popular of the innovative products or services of some enterprises than those with larger scales. Aiming at employees in high-tech industry in Guanxi Province, total 500 copies of questionnaire are randomly distributed, and 337 valid copies are retrieved, with the retrieval rate 67%. The research results reveal significantly positive correlations between 1.entrepreneurial culture and sustainable innovation capability, 2.sustainable innovation capability and patent, and 3.entrepreneurial culture and patent. According to the results, suggestions are proposed, expecting to explain how a high-tech business outperforms in the changeable digital era and acquires the sustainable innovation capability and patent to grasp the opportunity.

Virus diseases of strawberry present several complex problems. More than 25 viruses have been described in the genus Fragaria thus far. Here, we describe a novel rhabdovirus, tentatively named strawberry virus 1 (StrV-1), that infects F. ananassa and F. vesca plants. Genomic sequences of three distinct StrV-1 genotypes co-infecting a single F. ananassa host were obtained using combined Illumina and Ion Proton high-throughput sequencing. StrV-1 was transmitted to herbaceous plants via Aphis fabae and A. ruborum, further mechanically transmitted to Nicotiana occidentalis 37B and sub-transferred to N. benthamiana, N. benthamiana DCL2/4i, N. occidentalis 37B and Physalis floridana plants. Irregular chlorotic sectors on leaf blades and the multiplication of calyx leaves seem to be the diagnostic symptoms for StrV-1 on indexed F. vesca clones. StrV-1 was detected in asymptomatic grafted plants and in 49 out of 159 field strawberry samples via RT-PCR followed by Sanger sequencing. The bacilliform shape of the virions, which have a cytoplasm-limited distribution, their size, and phylogenetic relationships support the assignment of StrV-1 to a distinct species of the genus Cytorhabdovirus. Acyrthosiphon malvae, A. fabae and A. ruborum were shown to transmit StrV-1 under experimental conditions.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

Increasing the quality factor (Q) of an optical resonator device has been a research focus to be utilized in various applications. Higher Q-factor means light is confined in a longer time which will produce a shaper peak and higher transmission. In this paper, we introduce a novel technique to increase further the Q-factor of a one-dimensional photonic crystal (1D PhC) cavity device by using an end loop-mirror (ELM). The technique utilizes and recycles the light transmission from the conventional 1D PhC cavity design. The design has been proved to work by using the 2.5D FDTD simulation with Lumerical FDTD and MODE softwares. By using the ELM technique, the Q- factor of a 1D PhC design has been shown to have increased up to 79.53 % from the initial Q value without the ELM. This novel design technique can be combined with any high Q-factor and very high Q-factor designs to increase more the Q-factor value of a photonic crystal cavity devices or any other suitable optical resonator devices. The experimental result shows that the device is measurable by adding a Y-branch component to the one-port structure and able to get the high-Q result.

The group III two-component hybrid histidine kinase MoHik1p in the filamentous fungus Magnaporthe oryzae is known to be a sensor for external osmotic stress and essential for the fungicidal activity of the phenylpyrrole fludioxonil. The mode of action of fludioxonil has not yet been completely clarified but rather assumed to hyperactivate the high osmolarity glycerol (HOG) signaling pathway. To date, not much is known about the detailed molecular mechanism of how osmotic stress is detected or fungicidal activity is initiated within the HOG pathway. The molecular mechanism of signaling was studied using a mutant strain in which the HisKA signaling domain was modified by an amino acid change of histidine H736 to alanine A736. We found that MoHik1pH736A is as resistant to fludioxonil but not as sensitive to osmotic stress as the null mutant ∆Mohik1. H736 is required for fludioxonil action but is not essential for sensing sorbitol stress. Consequently, this report provides evidence of the difference in the molecular mechanism of fludioxonil action and the perception of osmotic stress. This is an excellent basis to understand the successful phenylpyrrole-fungicides’ mode of action better and will give new ideas to decipher cellular signaling mechanisms.

Sustainability is very important in business. The residential high-rise building all firms wanted to successful and sustainability in business. There is need the construction to completed low time, low cost and high quality in construction work. Therefore, real estate developers must find various strategies to use in construction projects to achieve goals and success of the firm. The purpose of this study was to indicate the very importance of knowledge management can lead to sustainability in business. Analyze 14 critical success to sustainability in residential high-rise building projects, collected questions from literature review, and survey in deep interview senior managers of 15 projects real estate development firms listed on the stock market of Thailand. Budget building more than 1000 million baht per project. From conceptual frame work five foundations integrated to knowledge management of critical success (KMITL PROCESS) used made tool survey in deep interview the critical success to sustainability in residential high-rise building project from project managers. Used IBM SPSS evaluated the critical success to sustainability. Found was one very important of critical success to sustainability, which was quality of products x̄ = 4.83. All 14 critical success to sustainability was found can applied made the knowledge management of critical success to sustainability in residential high-rise building project in firm. Especially in the field of construction managements project can used improve of all construction projects.

The Gleeble-1500D thermal simulation test machine was used to conduct the isothermal compression test on 21-4N at the strain rate ( ) of 0.01-10s-1, the deformation temperature (T) of 1273-1453K and the maximum deformation is 0.916. The data of the stress-strain ( - )were obtained. Based on the - data, the Johnson-Cook (J-C), modified J-C, Arrhenius and Back-Propagation Artificial Neural Network (BP-ANN) models were established. The accuracy of four models were verified, analyzed and compared. The results show that J-C model has a higher accuracy only under reference deformation conditions. When the deformation condition changes greatly, the accuracy of J-C model is significantly reduced. The coupling effect of T and of modified J-C model is considered, and the prediction accuracy is greatly improved The Arrhenius model introduces Zener-Hollomon (Z) to represent the coupling effect of T and , it has a fairly high prediction accuracy. And it can predict flow stress ( ) accurately at different conditions. The accuracy of BP-ANN model is the highest, but its learning rate is low, the learning and memory are unstable. It has no memory for the weights and thresholds of the completed training. So, there are certain limitations of it in use. Finally, a FEM of the isothermal compression experiment for four models were established, and the distribution of the equivalent stress field, equivalent strain field and temperature field with the deformation degree of 60% were obtained.

The rapid expansion of transcriptomics from increased affordability of next-generation sequencing (NGS) technologies generates rocketing amounts of gene expression data across biology and medicine, and notably in cancer research. Concomitantly, many bioinformatics tools were developed to streamline gene expression analysis and quantification. We tested the concordance of NGS RNA sequencing (RNA-seq) analysis outcomes between the two predominant programs for reads alignment, HISAT2 and STAR, and the two most popular programs for quantifying gene expression in NGS experiments, edgeR and DESeq2, using RNA-seq data from a series of breast cancer progression specimens, which include histologically confirmed normal, early neoplasia, ductal carcinoma in situ and infiltrating ductal carcinoma samples microdissected from formalin fixed, paraffin embedded (FFPE) breast tissue blocks. We identified significant differences in aligners’ performance: HISAT2 was prone to misalign reads to retrogene genomic loci, STAR generated more precise alignments, especially for early neoplasia samples. edgeR and DESeq2 produced similar lists of differentially expressed genes in stage comparisons, with edgeR producing more conservative, though shorter, lists of genes. Albeit, Gene Ontology (GO) enrichment analysis revealed no skewness in significant GO categories identified among differentially expressed genes by edgeR vs DESeq2. As transcriptome analysis of archived FFPE samples becomes a vanguard of precision medicine, identification and fine-tuning of bioinformatics tools becomes critical for clinical research. Our results indicate that STAR and edgeR are well-suited tools for differential gene expression analysis from FFPE samples.

Background: Antiplatelet medications such as aspirin and clopidogrel are used following thrombotic stroke or transient ischemic attack (TIA) to prevent a recurrent stroke. However, the antiplatelet treatments fail frequently, and patients experience recurrent stroke. One approach to lower the rates of recurrence, may be the individualized antiplatelet therapies (antiplatelet therapy modification (ATM)) based on the results of platelet function analysis (PFA). This review was undertaken to gather and analyse the evidence about the effectiveness of such approaches. Methods: We searched Medline, CINAHL, Embase, Web of Science and Cochrane databases to 7 January 2020. Results: Two observational studies involving 1136 patients were included. The overall effects of PFA-based ATM on recurrent strokes (OR 1.05; 95% CI 0.69 to 1.58), any bleeding risk (OR 1.39; 95% CI 0.92 to 2.10) or death hazard from any cause (OR 1.19; 95% CI 0.62 to 2.29) were not significantly different from the standard antiplatelet therapy without ATM. Conclusions: The two studies showed opposite effects of PFA-guided ATM on the recurrent strokes in aspirin non-responders, leading to an insignificant difference in the subgroup meta-analysis (OR 1.59; 95% CI 0.07 to 33.77), while the rates of any bleeding events (OR 1.04; 95% CI 0.49 to 2.17) or death from any cause (OR 1.17; 95% CI 0.41 to 3.35) were not significantly different between aspirin non-responders with ATM and those without ATM. There is a need for large randomized controlled trials which account for potential confounders such as ischemic stroke subtypes, technical variations in the testing protocols, patient adherence to therapy, and pharmacogenetic differences.

The increased consumption of high fat-containing foods has been linked to the prevalence of obesity and abnormal metabolic syndromes. Rhizopus oligosporus, a fungus in the family Mucoraceae, is widely used as a starter for homemade tempeh. Although R. oligosporus can prevent the growth of other microorganisms, it grows well with lactic acid bacteria (LAB). Lactobacillus plantarum can produce β-glucosidase, which catalyzes the hydrolysis of glucoside isoflavones into aglycones (with greater bioavailability). Therefore, the development of a soybean-based functional food by the co-inoculation of R. oligosporus and L. plantarum is a promising approach to increase the bioactivity of tempeh. In this study, the ameliorative effect of L. plantarum in soy tempeh on abnormal carbohydrate metabolism in high-fat diet (HFD)-induced hyperglycemic rats was evaluated. The co-incubation of L. plantarum with R. oligosporus during soy tempeh fermentation reduced the homeostatic model assessment of insulin resistance, HbA1c, serum glucose, total cholesterol, triglyceride, free fatty acid, insulin, and low-density lipoprotein contents and significantly increased the high-density lipoprotein content in HFD rats. It also increased the LAB counts as well as the bile acid, cholesterol, triglyceride, and short-chain fatty acid contents in the feces of HFD rats. Our results suggested that the modulation of serum glucose and lipid levels by LAB occurs via alterations in the internal microbiota, leading to the inhibition of cholesterol synthesis and promotion of lipolysis. Tempeh, produced with both L. plantarum and R. oligosporus, may be a beneficial dietary supplement for individuals with abnormal carbohydrate metabolism.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes, while axial canal is the largest canal amongst the network and distributes at the center of a coral branch. However, previous studies indicated that, in the non-radial symmetry transport system of Acropora, axial canal do not play a major role in the transport of hydroplasm, and the action of axial canal in coral growth is still obscure. In this study, we reconstructed six Acropora muricata samples by high resolution micro-computed tomography to investigate the growth patterns of axial canals during the processes of new branch forming and truncated branch rebuilding. We found that the axial canal of a new branch is transformed from a calice and the polyps in the new branch are budded from the polyp in the axial canal. Meanwhile, the axial canal can transport the calcareous skeletons to rebuild the tip of a truncated branch, which represents as the change in the diameter of axial canal and calcareous deposition/reduction in it. This work indicate the regulation of axial canal in the growth processes including budding, branching, and mineralising of an Acropora colony.

Conventional radiation therapy uses white X-rays that consist of a mixture of X-ray waves with various energy levels. In contrast, a monochromatic X-ray (monoenergetic X-ray) has a single energy level. Irradiation of high Z elements with a synchrotron generated monochromatic X-ray with the energy at or higher than the K-edge energy of the element results in the production of the Auger electrons that cause DNA damage leading to cell killing. Delivery of high Z elements into cancer cells and tumor mass can be facilitated by the use of nanoparticles. Mesoporous silica nanoparticles (MSNs) have been shown to be effective in delivering high Z elements to cancer cells. A proof of principle experiment was reported that demonstrated the feasibility of this approach. This opens up a possibility to pursue the Auger cancer therapy by the combined use of MSNs loaded with high Z elements and monochromatic X-rays. Similar cancer therapies using other types of quantum beams such as neutron, proton and carbon ion beams can be envisioned.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

Karst rocky desertification (KRD) is a process where strong anthropogenic disturbances and exposure of carbonate bedrock occurs in fragile karst ecosystems. The fractional cover of rocky outcrops is a key indicator and mechanistic driver of KRD and can be accurately assessed using remote sensing technology. Nevertheless, rugged karst terrain relief can cause shadow effects on satellite imagery and combine with high heterogeneity of karst landscapes to prevent fractional cover retrievals. In this study, we explored the feasibility of applying multispectral high spatial resolution ALOS imagery for fractional cover extraction of rocky outcrops. We selected the dimidiate pixel model (DPM), which has been applied in previous studies, and spectral mixture analysis (SMA; including simple endmember spectral mixture analysis (SESMA) and multiple endmember spectral mixture analysis (MESMA)) to explore the feasibility of using remote images for KRD monitoring and improve accuracy for estimating fractions. Results from MESMA achieved high overall accuracy (76.4%) in monitoring percentage of rocky outcrop fraction in the study area. SESMA appears to underestimate percentage of rocky outcrop likely because the development of KRD was driven by complex factors (soil erosion, dissolution and anthropogenic disturbances). This results in spectral reflectance of rocky outcrop being variable in different settings. Predicted exposed bedrock coverage using SESMA and MESMA was similar in sun-lit and shaded areas although predictions from SESMA were smaller than reference data. DPM underestimated the fractional cover of rocky outcrops on south-facing slopes and overestimated it in shaded areas. Furthermore, SESMA and MESMA effectively reduced topographic effects. We conclude that it is better to extract percentage of rocky outcrop using MESMA in the karst region of southwestern China. Remote sensing is emerging as a feasible method to extract surface condition information in heterogeneous and rugged landscapes.

Obesity and metabolic disorders can be risk factors for the onset and development of neurodegenerative diseases. The aim of the present study was to investigate the protective effects on dysmetabolism and neurodegeneration of a natural dietary supplement (NDS), containing Curcuma longa, silymarin, guggul, chlorogenic acid and inulin, on the brains of high fat diet (HFD)-fed mice. A decreased expression of FACL-4, CerS-1 and CerS-4, reduced cholesterol concentration, increased IR expression and insulin signaling activation, were found in brains of NDS-treated HFD mice, suggesting that NDS is able to prevent brain lipid accumulation and central insulin resistance. In the brains of NDS-treated HFD mice, the levels of RNS, ROS and lipid peroxidation, the expression of p-ERK, H-Oxy, i-NOS, HSP60, NF-kB, GFAP, IL-1β, IL-6, and CD4 positive cell infiltration were lower than in untreated HFD mice, suggesting antioxidant and anti-inflammatory effects of NDS. The decreased expression of p-ERK and GFAP in NDS-treated HFD mice was confirmed by immunofluorescence. Lastly, a lower number of apoptotic nuclei was found in cortical sections of NDS-treated HFD. All these data indicate that NDS exerts neuroprotective effects in HFD mice by reducing brain fat accumulation, oxidative stress and inflammation and improving brain insulin resistance.

Development of effective treatments for high-grade glioma (HGG) is hampered by 1) the blood-brain barrier (BBB), 2) an infiltrative growth pattern, 3) rapid development of therapeutic resistance, and, in many cases, 4) dose-limiting toxicity due to systemic exposure. Convec-tion-enhanced delivery (CED) has the potential to significantly limit systemic toxicity and in-crease therapeutic index by directly delivering homogenous drug concentrations to the site of disease. In this review, we present clinical experiences and preclinical developments of CED in the setting of high-grade gliomas.

The interaction of electrons with strong laser fields is usually treated with semiclassical theory, where the laser is represented by an external field. There are analytic solutions for the free electron wave functions, which incorporate the interaction with the laser field exactly, but the joint effect of the atomic binding potential presents an obstacle for the analysis. Moreover, the radiation is a dynamical system, the number of photons changes during the interactions. Thus, it is legitimate to ask how can one treat the high order processes nonperturbatively, in such a way that the electron-atom interaction and the quantized nature of radiation be simultaneously taken into account? An analytic method is proposed to answer this question in the framework of nonrelativistic quantum electrodynamics. As an application, a quantum optical generalization of the strong-field Kramers-Heisenberg formula is derived for describing high-harmonic generation. Our formalism is suitable to analyse, among various quantal effects, the possible role of arbitrary photon statistics of the incoming field. The present paper is dedicated to the memory of Prof. Dr. Fritz Ehlotzky, who had significantly contributed to the theory of strong-field phenomena over many decades.

It is agreed that before the creation of particles, space was absolutely devoid of matter and radiation. In this study, we assume that the absolute void comprises four dimensions; three spatial dimensions and a force equivalent representing the factor of change among the elementary dimensions. Our hypothesis is based on the expansion of the spatial dimensions, and the subsequent space instability. We demonstrated that when the outward force equivalent strength exceeds a critical limit, it collapses inward to restore equilibrium in the system. Then, the void inside the collapsed force equivalent acts as a void in a confined system, the energy of the system remains conserved at all stages. With the decrease of the spatial dimensions due to the collapse the energy density increases, at the final stage the energy in the confined system is concentrated forming a solid state of energy. In which, this solid state of energy is a particle become the source of the elementary particles. The created high-energy sources are controlled by the internal and external forces of the source and all entities in its external force field until equilibrium is reached. The article gives the summary of Big bang theory and its problems which are further discussed in inflation. This article will help in understanding that how elementary dimensions play a role in the formation of elementary particles. The quark gluon plasma, inflation, gravitational collapse, and gravitational lensing provide evidence supporting the elementary dimensions theory presented in this paper.

As metabolomics is widely used in the study of disease mechanisms, more and more studies have found that metabolites play an important role in the occurrence of diseases. The aim of this study is to investigate the effects and mechanisms of quercetin in high-fat-sucrose diet (HFD)-induced nonalcoholic fatty liver disease (NAFLD) development using nontargeted metabolomics. A rat model of NAFLD was established by feeding with a HFD for 30 and 50 days. Results indicated quercetin exhibited hepatoprotective activity in HFD-induced NAFLD rats in 30 days by regulating fatty acids related metabolites (adrenic acid, etc.), inflammation related metabolites (arachidonic acid, etc.), oxidative stress related metabolites (2-hydroxybutyric acid) and other differential metabolites (citric acid, etc.). However, quercetin couldn’t improve NAFLD in 50 days maybe it couldn’t reverse the inflammation condition induced by long-term high-fat diet. These data indicate that dietary quercetin may be beneficial to NAFLD at early stages. Furthermore, combining metabolomics and experimental approaches opens up avenues of effects and mechanisms of drugs for complex diseases.

Climate change is expected to increase the frequency and severity of abiotic stresses that lead to loss of crop yield. We investigated the effect of salinity (S), short episodes of high temperature (HS) and combination of S+HS at the reproductive phase on dead pericarps properties and yield of the crop plant Brassica juncea. Three intervals of HS resulted in massive seed abortion; seeds from salt-treated plants germinated poorly. Pericarp extracts of salt-treated plants reduced seed germination of B. juncea; all pericarp extracts completely inhibited seed germination of tomato and Arabidopsis; removal of pericarp extracts restored seed germination. HS reduced all metabolites accumulated in dead pericarps, except for upregulation of isomaltose and cellobiose. Salt induced alteration in metabolite levels including increase in proline, reduction in TCA intermediates and changes in phytohormone levels. Proteome analysis revealed hundreds of proteins stored in dead pericarps whose levels and composition were altered under salt stress. The integration of metabolic and proteomic data showed that changes in metabolites were highly correlated with changes in proteins involved in their biosynthetic pathways. Thus, besides providing a physical shield for seed/embryo protection dead pericarps store beneficial substances whose levels, composition and biological function are altered under stress, further highlighting the elaborated function of dead organs enclosing embryos in seed biology and ecology. The detrimental effect of HS on crop production might have implications for global food security in the face of climate change.

Towns emerged as dynamic economic and political centers during the Middle Ages, giving rise to the emergence of new social classes. As a result of these functions, a new relationship began to be forged with the rural world, which supplied towns with foodstuffs that satisfied new social demands. Archaeobotanical analysis (carpology) allows us to understand the flow of cash crops by tracing seeds and fruits produced in the countryside that were consumed in and redistributed from the towns. The study of waterlogged contexts from medieval archaeological sites in the Kingdom of Galicia (Santiago de Compostela, Padrón, and Pontevedra) has provided a set of species that played a crucial role in the economy of the urban dwellers and that possibly were related to differential access or food preferences. Evidence for fruits (grapes, chestnuts, figs, apples, and cherries, among others), garden crops (melon), and cereals (foxtail millet, rye, naked wheat, and oat) has been documented. Broomcorn millet is particularly abundant, demonstrating that it was important for subsistence. Some of the species found (medlar and turnip/grelo) are novel in the archaeobotanical literature of the medieval period in the Iberian Peninsula.

Three-dimensional (3D) cell culture is considered more clinically relevant in mimicking the structural and physiological conditions of tumors in vivo compared to two-dimensional cell cultures. In recent years, high-throughput screening (HTS) in 3D cell arrays has been extensively used for drug discovery because of its usability and applicability. Herein, we developed a microfluidic spheroid culture device (μFSCD) with a concentration gradient generator (CGG) that enabled cells to form spheroids and grow in the presence of cancer drug gradients. The device is composed of concave microwells with several serpentine micro-channels which generate a concentration gradient. Once the colon cancer cells (HCT116) formed a single spheroid (approximately 120 μm in diameter) in each microwell, spheroids were perfused in the presence of the cancer drug gradient irinotecan for 3 days. The number of spheroids, roundness, and cell viability, were inversely proportional to the drug concentration. These results suggest that the μFSCD with a CGG has the potential to become an HTS platform for screening the efficacy of cancer drugs.

Cyanobacteria are microorganisms able to adapt to a wide variety of environmental conditions and abiotic stresses. They produce a very large number of metabolites that can participate in the adaptation of cyanobacteria to a large range of resources such as light, temperature, or nutrient. The metabolites variation is one way to understand the physiological status and adaptation of cells. In this study, we aim to understand how the diversity and the dynamics of the whole metabolome is dependent of the growth phases and under control of abiotic factors (e.g. light intensity and temperature). The cyanobacteria Aliinostoc sp. PMC 882.14 was selected for its large number of biosynthetic gene clusters. Metabolomes were analyzed by using mass spectrometry (qTOF-MS/MS) combined with untargeted analysis to investigate the metabolite dynamics. Significant variations were characterized between exponential and stationary phases, whatever the culture conditions (“control”, “higher light”, or “higher temperature”). ”Higher light” and “higher temperature” favored the synthesis of metabolites belonging to the same molecular families. Among highly regulated metabolites, we observe the presence of mycosporine-like amino acids (MAAs), and various variants of somamides, microginins, and microviridins. Through Aliinostoc sp. PMC 882.14, this study shows the importance of knowing the physiological state of cyanobacteria for comparative global metabolomics and questions the regulation processes involve into metabolite families production. Our results also open up new perspectives in the context of the production of targeted bioactive metabolites.