Durability of concrete requires a dense microstructure which can be achieved by using self-compacting concrete (SCC). Both calcined clay (CC) and rice husk ash (RHA) are promising supplementary cementitious materials (SCMs) that can partially replace cement, but their use in SCC is critical due to their higher water demand and specific surface area (SSA) compared to cement. Empirical method of SCC design was adopted considering the physical properties of both CC and RHA. The influence of partially substituting cement at 20 vol-% with binary and ternary blends of CC and RHA were investigated. The fresh properties of SCC were investigated using a variety of tests. The time dependent workability was monitored by plunger method and flow resistance determined based on the rheological measurements of SCC. The evolution of the hydrate phases of the binder in SCC was determined by thermogravimetric analysis, while the durability was evaluated by rapid chloride migration test. Cement partial replacement with 20 vol-% CC has no significant effect on SCC fresh, time dependent, compressive strength and durability properties. 20 vol-% RHA on the other hand requires higher dosage of SP to achieve self-compactability and increased the viscosity of SCC. Its workability retention is only up to 30 min after mixing and exhibited higher flow resistance. It consumes more CH and improves compressive strength and chloride resistance of SCC. The ternary blending with CC and RHA yielded better fresh SCC properties compared to the binary blend with RHA, while an improved chloride penetration resistance could be achieved compared to binary CC blend.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

Given the significant role of the Ningxia Urban Agglomeration along the Yellow River in reshaping the urban network and promoting coordinated development in the upper Yellow River region of China, this paper takes enterprise flow as the explicit manifestation of the regional urban network. Based on the data of registered enterprises from 2005 to 2021, combined with the interlocking network model, social network analysis method, and spatial panel econometric model, this paper interprets the evolution of the regional urban network structure and its influencing mechanisms through the different types of enterprise flow. The results indicate the following: (1) The external network is primarily focused on outflow investments towards North China, East China, and Northwest China. The overall inflow sources form a multi-origin structure dominated by North China and East China. The Jinfeng and Xingqing serve as core hubs for enterprise exports in the external network and destinations for incoming enterprises. However, in the Productive manufacturing connections, a spatial organizational pattern driven by multiple cities has formed. (2) In the internal network, a concentric connection structure centered around the Jinfeng and Xingqing has formed. The Productive service connections are relatively active, while the Productive manufacturing connections are relatively concentrated between the Jinfeng, Xingqing, Ningdong, and Lingwu. However, there is an imbalance in the spatial connections within the urban agglomeration network and an incomplete hierarchical system of network nodes. (3) In the external network, the main feature is the absorption of external elements to foster development momentum. In the internal network, the Jinfeng and Xingqing serve as contact and radiation sources, influencing various nodes. However, their driving capacity is weak. (4) The market demand and coordinated development both demonstrate significant promoting effects on the connections within the external and internal networks. The sluggish adjustment and transformation of regional industrial structure have resulted in a temporary negative inhibitory effect on the development of transformation. The negative impact of urban investment activities and the positive impact of government management are reflected within the internal network. (5) The improvement of urban management and service functions, as well as external borrowing, can promote the connection in different network. However, the borrowing economic activity can have a negative impact in different networks. (6) Industrial agglomeration can promote enterprises connections in different networks and generate significant spatial spillover effects.

A new longitudinal flow heat dissipation theory for cylindrical batteries is proposed in order to increase the energy density and uniform temperature performance of cylindrical lithium-ion battery packs while also shrinking their size by roughly 10%. First, a genetic algorithm is used to identify the single cell's thermal properties. Based on this, modeling and simulation are used to examine the thermal properties of the longitudinal flow-cooled battery pack. It is found that the best coolant flow scheme has one inlet and one outlet from the end face, taking into account the cooling effect of the battery pack and engineering viability. Lastly, Thermal Dummy Cells (TDC) is used to conduct a validation test of the liquid cooling strategy. Additionally, the simulation and test results demonstrated that the liquid cooling solution can keep the battery pack's maximum temperature rise under the static conditions of a continuous, high-current discharge at a rate of 3C to 20 °C and under the dynamic conditions of the New European Driving Cycle (NEDC) to 2 °C. In applications where the space requirements for the battery pack are quite severe, the longitudinal flow cooling method has some advantages.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

It is a challenging and meaningful task to carry out drone-based livestock monitoring in high-altitude and cold regions. The purpose of AI is to execute automated tasks and to solve practical problems in actual applications by combining the software technology with the hardware carrier to create integrated advanced devices. Only in this way, the maximum value of AI could be realized. In this paper, a real-time tracking system with dynamic target tracking ability is proposed. It is developed based on the tracking-by-detection architecture using YOLOv7 and DeepSORT algorithms for target detection and tracking, respectively. To address the existing problems of the DeepSORT algorithm, the following two optimizations are made: (1) Optical flow is used to compensate the Kalman filter for improvement of the prediction accuracy; (2) A low-confidence trajectory filtering method is adopted to reduce the influence of unreliable detection on target tracking. In addition, an visual servo controller for the UAV is designed to enable the automated tracking task. Finally, the system is tested using the Tibetan yaks living in the Tibetan Plateau as the tracking targets, and the results reveal the real-time multiple tracking ability and the ideal visual servo effect of the proposed system.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

A retrospective cohort study was performed to determine the likelihood of malignant stroke after mechanical thrombectomy via ASPECTS-PASS score(A-P score), a novel scoring system using ASPECT score and number of arterial-passes. This prediction score is designed to help clinicians take early measures. Malignant stroke is defined as a large MCA infarct with mass effect that develops during the first 5 days following presentation and is associated with approximately 80% mortality. Previous studies have shown an association of low ASPECTS and high number of passes with poor outcome.We performed a retrospective cohort analysis on 78 patients with anterior circulation stroke who underwent mechanical thrombectomy at our hospital. We analyzed the likelihood of developing malignant stroke post thrombectomy in the first 5 days following successful recanalization (TICI ≽ 2b). Malignant stroke is defined as severe symptoms secondary to edema as evidenced by midline shift, cistern engorgement, and hemorrhagic conversion with edema. Patients with ASPECTS of 0-5 were excluded. We used two variables to predict the outcome: ASPECT score and number-of-passes. We used the equation ASPECT score minus number-of-passes (A-P) to arrive at a single number to predict the risk of malignant stroke. A-P scoring scale ranged from 0-9. Our study showed a statistically significant inverse relationship of A-P score and risk of malignant stroke. Approximately 90% of patients with A-P score < 5 developed malignant stroke in our study. A-P score can help predict malignant stroke post thrombectomy even after successful recanalization. Thus, A-P score of ≤ 5 suggests very high risk. (A-P) Score can assist clinicians to take early measures, and thereby prevent worse outcomes.

Non-normal mode stability analysis has long been employed to study linear transient characteristics of wall bounded shear flows. However, the application of this approach to investigate shear flows with stratified thermal conditions (STCF) has received limited attention. This paper examines thermal effects on Taylor-Couette flow. The results in this study indicate the possibility of a subcritical bifurcation in stratified Taylor-Couette flow.

The increasing popularity of unconventional wells has sparked a heightened interest in evaluating and predicting their production performance. With the use of extended reach well structures, these wells are able to generate and access larger reservoir volumes. Hence, it is crucial to understand how the well's lateral trajectory affects its transient production performance. The assessment of lateral trajectory undulating amplitude effect on the flow behavior is performed in the current study based on the experimental results obtained at the University of North Dakota, Undulated Two-Phase (UTP) Flow Loop, injecting air and water mixture through a variable undulating amplitude section followed by a vertical section. The experiments showed that the undulating amplitude increase induced lower translational velocity, frequency, and length, with a consistent slug acceleration through the system profile from the inlet to the vertical section and a decreasing frequency when the slugs travel through the vertical section. Measured data shows that an increase of the horizontal pressure losses and variability is expected with a higher undulation amplitude, translating the fact that larger instabilities are observed for higher amplitudes. The numerical simulation predicted lower translational velocity and frequency, higher slug’s lengths, and similar vertical pressure losses when compared to the experimental results.

Transarterial embolization (TAE) for high-flow pancreaticoduodenal artery (PDA) aneurysms in patients with celiac-trunk stenosis by the median arcuate ligament (MAL) has been found effective both after rupturing and to prevent rupture. The objective was to describe the TAE techniques used and their effectiveness in excluding PDA aneurysms due to MAL syndrome. This single-center retrospective study done at the Dijon-Bourgogne University Hospital included all patients treated by TAE in 2010–2022 for ruptured or unruptured high-flow PDA aneurysms caused by MAL syndrome. We identified 14 patients (7 women and 7 men; mean age, 64 years). Packing and trapping techniques were used alone or together. Occlusion was with microcoils, co-polymer, or cyanoacrylate glue, used separately or combined. Technical success was achieved in 13 (93%) patients. Clinical success was achieved in 12 (86%) patients. One major and two minor complications were recorded within the first 30 days. No complications occurred after 30 days. Follow-up ranged from 1 to 84 months. No cases of aneurysm recanalization were recorded to date. TAE had high technical and clinical success rates in our patients with unruptured or ruptured PDA aneurysms due to MAL syndrome.

Hypertension and arterial stiffness are the main factors contributing to cardiovascular disease. L-citrulline, a nitric oxide precursor, has been proposed as a blood pressure-lowering intervention. This study aimed to investigate the impact of L-citrulline on central and peripheral blood pressure, arterial stiffness, and muscle oxygenation at rest and during an isometric knee extension exercise protocol. Twelve older males received 6 g of L-citrulline or a placebo for six days using a double-blind crossover design. Blood hemodynamics parameters (i.e., arterial and brachial systolic and diastolic blood pressure, mean arterial pressure, pulse pressure, heart rate), arterial stiffness (i.e., augmented pressure, augmentation index, forward, backward wave pressure and carotid-femoral pulse wave velocity) and muscle oxygenation [i.e., oxyhemoglobin (Δ[O2Hb]) and deoxyhemoglobin (Δ[HHb]), total hemoglobin concentration (Δ[tHb]) and tissue saturation index (TSI%)], were measured at baseline, post-supplementation and during isometric exercise. No significant effects of L-citrulline supplementation were observed at rest or during exercise on blood pressure, arterial stiffness, and muscle blood flow. Both central and peripheral blood pressure were increased during the exercise, which is consistent with isometric contractions. The results of the present study question the efficacy of short-term L-citrulline in decreasing blood pressure at rest or attenuating blood pressure increases during isometric exercise.

The paper presents the results of modeling the problem of injecting liquid sulfur dioxide into a porous reservoir initially saturated with methane and ice. The model presented in the paper assumes the formation of three different regions, namely, the near one, saturated with liquid SO2 and its hydrate; the far one, containing methane and ice, and the intermediate one, saturated with methane and water. The effects of various parameters of the porous medium and injected SO2 on the nature of the course of the hydrate formation process have been studied. It is shown that with a decrease in reservoir permeability or injection pressure, the length of the intermediate region decreases, which in the limiting case means the formation of SO2 hydrate in the mode without the formation of an extended region saturated with methane and water. It is shown that such a regime is also typical for the case of high initial injection pressures, as well as low values of the initial reservoir temperature and injection temperature.

The research is devoted to the problem of noise generation during flights of supersonic civil aircrafts. The effect of a thermally stratified energy source used to control the flow past a pointed cylinder aerodynamic models on the nearfield and ground pressure signatures, as well as on the perceived loudness in decibels (PLdB) on the ground is evaluated. The fields of parameters and the dynamics of the drag forces are studied for different values of temperature in the layers of the thermally stratified energy source and for different number of layers in it. It has been shown that when performing the flow control at freestream Mach numbers 1.5-2 using thermally stratified energy sources with the number of layers from 2.5 to 7.5 and rarefaction parameters in the layers from 0.15 to 0.3, no additional noise impact on the ground is introduced. Thus, the simulations showed that changing the surface pressure signature due to drag reduction does not necessarily imply a change in the PLdB on the ground.

We present our experience with the implantation of flow diverter stents (FDSs) for the management of intern carotid artery (ICA) dissections in tortuous tonsillar loop segments. 16 patients (10 women, 62.5%; mean age 39±8 years; median baseline NIHSS 13; median ASPECTS 8.5) with acute ischemic stroke due to ICA dissection in a tortuous tonsillar loop segment, with/without large intracranial vessel thrombotic occlusion, from 6/2015−2/2022 were included in this retrospective study under a waiver of informed consent. An FDS device was deployed from the petrous ICA toward the upper cervical ICA, completely covering the tonsillar loop. Stentriever-assisted thrombectomy was performed when indicated. A dual antiplatelet regimen was used during and after the procedure. Thrombocyte inhibition levels were evaluated before, during, and after the intervention. The ICA occlusion/near occlusion was successfully recanalized in all 16 patients with postangioplasty residual stenosis of 34±14% (range 0−50%). Stent-assisted embolectomy was performed in 15/16 patients (93.7%), achieving revascularization (TICI 2b−3) in all. There were no procedural complications and no intraprocedural embolic events; one asymptomatic petechial hemorrhage was detected. At 3-month follow-up, mRS 0−2 was seen in all patients. This report provides pilot data for a subsequent study on the use of flow diverter stents for ischemic cerebrovascular conditions. Our encouraging preliminary results await confirmation from further experience and prospective randomized studies.

Temporary streams are a key component of the hydrological cycle in arid and semi-arid regions, but their flow is highly variable and difficult to measure. In this paper, we present a novel approach that could be used to assess the flow of temporary streams and characterize their environmental status. Specifically, we apply the Image Velocimetry method to estimate surface velocity in temporary streams using unmanned aerial vehicles (UAVs) equipped with optical sensors (IV-UAV method). The IV-UAV method enables the easy, safe and quick estimation of the velocity on the water’s surface. This method was applied in different temporary streams in Lesvos Island, Greece. The produced results show that the IV-UAV can be implemented at low discharges, at temporary streams and at small streams. However, there were many occasions that measurements were unable due to various reasons such as dense vegetation or archaeological sites. Despite of this, the proposed methodology could be incorporated in optical protocols which are used to assess the environmental status of temporary streams of Mediterranean conditions. Finally, this would become a valuable tool for understanding the dynamics of these eco-systems and monitoring changes over time.

Tunneled central venous catheters (CVC) are mainly considered as rescue vascular access option in dialysis but still used in about one quarter of prevalent patients worldwide as being associated with poor performances and higher risks. Study design. In this retrospective single-center study, we aimed to report on clinical performances achieved with high-flow tunneled CVC (DualCath, DCath) and compared it with arteriovenous accesses (AVAs; AV fistula, AV graft, Thomas Shunt) in a hospital-based dialysis unit. Methods. Sixty-eight stage 5 chronic kidney disease dialysis dependent patients (CKD5D) receiving high volume hemodiafiltration were followed-up for 30 months. The study consisted of two phases: baseline cross-sectional and longitudinal follow-up of key performance indicators. Clinical performances consisting of effective blood flow and blood volume, recirculation, urea and ionic Kt/V and total Kt, ultrafiltration volume and percent reduction of ß2-M were measured monthly as part of quality control in our unit. Results. At baseline, effective blood flow with DCath was close to 400 ml/min, similar to AVAs. Recirculation with DCath (7%, 6-13%) was higher than AVAs. Diffusive dialysis dose delivered with DCath (spKt and eKt/V) and convective dialysis dose achieved with DCath were slightly lower than AVAs, but still much higher than recommended by guidelines. Percent reduction of ß2-M achieved with DCath was also 4 to 10% lower than AVAs. On longitudinal follow-up, main clinical performance indicators of DCath (total Kt and total ultrafiltration volume, L/session) were maintained very stable over time and close to those achieved with AVAs. Conclusions. As shown in this study, high-flow DualCath tunneled two single lumen silicone catheters may be used to deliver high volume hemodiafiltration in a reliable and consistent manner without compromising clinical performances. These results rely from the specific design of the two silicone cannulas and the strict adherence to best catheter practices.

Glycerol has found its applications as a heat-transfer fluid in heat exchangers, and as a compo-nent of functional solutions in biosensor analysis. Flowing non-aqueous fluids are known to be able to induce electromagnetic fields due to triboelectric effect. These triboelectrically generated electromagnetic fields can affect biological macromolecules. Horseradish peroxidase (HRP) is widely employed as a convenient model object for studying how external electric, magnetic, and electromagnetic fields affect enzymes. Herein, we have studied whether the flow of glycerol in a ground-shielded cylindrical coil affects the HRP enzyme incubated at a 2 cm distance near the coil’s side. Atomic force microscopy (AFM) has been employed in order to study the effect of glycerol flow on HRP at the nanoscale. Increased aggregation of HRP on mica has been observed after the incubation of the enzyme near the coil. Moreover, the enzymatic activity of HRP has also been affected. The results reported can find their application in biotechnology, food technology and life sciences application, considering the development of triboelectric generators, en-zyme-based biosensors and bioreactors with surface-immobilized enzymes. Our data can also be of interest for scientists studying triboelectric phenomena.

The pore-throat radius of shale oil reservoir is extremely small, and it is difficult to accurately obtain the absolute permeability and oil-water two-phase relative permeability of actual oil reservoir through conventional core experiments. However, these parameters are very important for reservoir numerical simulation. In this paper, a method for characterizing flow parameters based on pore network model that considers differential pressure flow and diffusion flow is proposed. Firstly, a digital core was reconstructed using focused ion beam scanning electron microscopy (FIB-SEM) from the Gulong shale reservoir in the Songliao Basin, China, and a pore network model was extracted. Secondly, quasi-static single-phase flow and two-phase flow equations considering diffusion were established in the pore network model. Finally, pore throat parameters, absolute permeability, and oil-water two-phase permeability curves were calculated, respectively. The results show that the pore throat distribution of Gulong shale reservoir is mainly concentrated in the nanometer scale, the mean pore radius is 87 nm, the mean throat radius is 41 nm, and the mean coordination number is 3.97; The calculated permeability considering diffusion is 0.000124mD, which is approximately twice the permeability calculated without considering diffusion; The irreducible water saturation of the Gulong shale reservoir is approximately 0.26, and the residual oil saturation is approximately 0.73. The method proposed in this paper can provide an important approach for characterizing the flow parameters of similar shale oil reservoirs.

This paper presented a two-dimensional, well-balanced hydrodynamic and sediment transport model based on the solutions of variable density shallow water equations (VDSWEs) for sediment-laden flows, and the Exner equation for bed changes. Those equations are solved in a coupled way by the first-order Godunov-type finite volume method. The Harten-Lax-van Leer-Contact (HLLC) Riemann solver is extended to find the local Riemann fluxes in order to maintain the exact balance between the momentum term and the bed slope term. The advantage of a well-balanced scheme over an unbalanced scheme is demonstrated by the synthetic standing contact-discontinuity test case. Then, the model is employed to simulate two laboratory experiments. At last, a field case, the 1996 Lake Ha! Ha! flood event (Canada), is simulated. Results of cross sectional geometries and profiles of longitudinal thalweg agree well with measurements. The accuracy and simplicity of the numerical model, together with the robust implementation, make the model a good candidate for practical engineering applications.

Data-Flow and Higher-Order Mutation are white-box testing techniques. To our knowledge, no work has been proposed to compare data flow and higher-order mutation. This paper compares all def-uses data-flow and second-order mutation criteria. This compassion investigates the subsumption relation between these two criteria and evaluates the effectiveness of test data developed for each. To compare the two criteria, a set of test data satisfying each criterion is generated, which is used to explore whether one criterion subsumes the other criterion and assess the effectiveness of the test set that was developed for one methodology in terms of the other. The results showed that the mean mutation coverage ratio of the all du-pairs adequate test cover is 80.9%, and the mean data flow coverage ratio of the 2nd-order mutant adequate test cover is 98.7%. Consequently, 2nd-order mutation “ProbSubsumes” the all du-pairs data flow. The failure detection efficiency of the mutation (98%) is significantly better than the failure detection efficiency of data flow (86%). Consequently, 2nd-order mutation testing is “ProbBetter” than all du-pairs data flow testing. In contrast, the size of the test suite of 2nd-order mutation is more significant than the size of the test suite of all du-pairs.

This study will present a comprehensive review of the two-phase flow boiling heat transfer coefficient of hydrocarbons such propane (R-290), butane (R-600) and iso-butane (R-600a) and ethanol at various experimental conditions. Studying the multiphase flow heat transfer coefficient has a crucial importance for many heat transfer equipment to achieve higher efficiency for more compact design and cost reduction. One reason behind choosing hydrocarbons as refrigerants in this study is because hydrocarbons have zero ozone depletion potential (ODP=0) and insignificant direct global warming potential (GWP = 3). Moreover, thermodynamic and thermophysical characteristics of hydrocarbons qualify them to be a strong candidate for more heat transfer applications. Initially, by constructing a database for the working fluids from various experimental work available in the literature. The current data that this study has collected for the flow boiling of spans wide ranges of parameters, such as: mass flux, heat flux, operating pressure, and saturation temperature, etc. Furthermore, by comparing the experimental multiphase heat transfer coefficient database with the anticipated values of each correlation, the prediction performance of 26 correlations found in the literature was assessed. This study leads to the selection of the best prediction method based on the minimum deviation of predicted results from the experimental database provided by calculated mean absolute error (MAE) from the assessed correlations. The findings of this study can also be useful in the development of more accurate correlation methods for these fluids and improve the prediction of their flow boiling characteristics.

For effective warehouse management, various criteria should be taken into consideration in terms of inventory management, demand, transportation distance, usage area, delivery-waiting times, and minimizing the costs that may arise from them. Because, the purpose of the product assignment problem is to minimize the total transport distance during storage and to reduce the space required for product assignment. However, the storage location assignment problem (SLAP) occurs simultaneously with production planning activities in real life. In this study, an integrated mixed-integer nonlinear (MINLP) mathematical model is proposed, which includes the assignment of products to storage areas and production planning, using the TOPSIS (Technique for Order Preference by Similarity to Ideal Solution) class based policy for storage systems where multiple criteria are important. In the TOPSIS class-based policy, weight and waiting time criteria are taken into account, as well as the COI (Cube-per-order index index), which is widely used in the literature. In addition, a decision support system flow has been proposed that takes into account the single criterion, multiple criteria and COI index criteria of the developed model and provides its integration with different product assignment policies. Detailed literature research; It has been revealed that the proposed mathematical model and decision support system flow have the feature of applying an existing field of science to a new problem.

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&amp;D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

Transition delaying is of great importance for the drag and heat flux reduction of hypersonic flight vehicles. The first mode within low frequency and the second mode within high frequency exist simultaneously during the transition of hypersonic boundary layer. This paper proposes a novel bi-frequency synthetic jet to suppress low- and high-frequency disturbances at the same time. Orthogonal table and variance analysis are used to compare the control effects of jet with different frequencies, amplitudes and positions. Linear stability analysis results show that, low frequency synthetic jet can suppress the first mode when it is arranged upstream of synchronization point, while the second mode control effect is relatively weak. The higher the high frequency is, the stronger the suppression effect is on the first mode. For the second mode, the suppression effect is only at f2=89.09kHz. The larger the amplitude, the weaker the promoting effect for the first mode and the second mode, and the more obvious the suppressing effect. For the cases with synthetic jet downstream of synchronization point, all levels of the three parameters promote the unstable mode. In terms of the growth rate with the spanwise wave number, the control effect of the same factor and level under different spanwise wave number is different. In order to obtain the optimal control effect on transition, the three factors and the arrangement position of the synthetic jet should be selected as follows: the position is arranged in the upstream, with f1 = 17.82kHz, f2 = 89.9kHz, a =0.007, so that the maximum growth rate of the first mode is reduced by 9.06% and that of the second mode is reduced by 1.28% compared with the uncontrolled state.

The shear factor of ore drawing is one of the important factors affecting the formation of underground debris flow, and it has an important contribution to the formation of underground debris flow. The purpose of this paper is to study the effect of mining shear factor on underground debris flow in natural caving method. Based on the research background of the underground debris flow in Plan copper mine, this paper analyzes the characteristics of the slurry material structure of the underground debris flow, the influence of drawing shear factor on formation mechanism of underground debris flow is analyzed. The results show that the slurry of the underground debris flow in Plan mine is not only a pseudoplastic fluid but also a thixotropic fluid. It is indicated that once there is shearing force in drawing, it will deform, and its viscosity will decrease with the increase of shear rate and time. It is considered that the shear force produced by the flow of ore particles first produces shear action on the paste in the shear boundary region of ore drawing, it is reduced in viscosity and increased in fluidity, so that its “Activation” and then become a flowable paste, along with the bulk ore flow through the mouth. The continuous ore drawing process will continuously shear the new moraine slurry in the ore drawing channel and continuously “Activate” the moraine slurry in the ore drawing channel, finally, a certain scale and destructive down-hole debris flow accident. This paper is the first to study the effect of ore drawing shear factor on the formation mechanism of underground debris flow. It not only broadens the research field of debris flow, but also fills up the deficiency of systematic research on underground debris flow, and provides theoretical guidance for the prevention and control of underground debris flow.

In this article, the biocatalytic oxidation of ethanol into acetaldehyde was studied using a catalase entrapped within monolithic polyampholyte cryogel, p(APTAC-co-AMPS), derived from an anionic monomer, 2-acrylamido-2-methyl-1-propanesulfonic acid sodium salt (AMPS), and a cationic monomer, (3-acrylamidopropyl) trimethylammonium chloride (APTAC) as catalyst. Macroporous polyampholyte cryogels containing various amounts of catalase were synthesized in situ under cryo-polymerization conditions at a molar ratio of monomers [APTAC]:[AMPS] = 75:25 mol.% in the presence of 10 mol.% cross-linking agent, N,N-methylenebisacrylamide (MBAA). The conversion of ethanol into acetaldehyde in good-to-high yields was observed in flow-through and batch type reactors under optimal conditions: at T = 10-20 C, pH = 7.1, [C2H5OH]:[H2O2] = 50:50 vol.%. According to SEM image the pore sizes of p(AMPS-co-APTAC) cryogel vary from 15 to 55 μm. The catalytic activity of catalase entrapped within monolithic polyampholyte cryogel in the conversion of ethanol into acetaldehyde was evaluated through the determination of such kinetic parameters as Michaelis constant (Km), the maximum enzymatic rate (Vmax), activation energy (Ea), turnover number (TON) and turnover frequency (TOF). The catalase encapsulated within monolithic polyampholyte cryogel exhibits a high conversion of ethanol into acetaldehyde. The advantages and disadvantages of flow-through and batch type reactors were highlighted.

N-acetyl-L-cysteine (NAC), a sulfhydryl-containing compound, is mainly used as a mucolytic and as an antidote for acetaminophen overdose. Flow injection and sequential injection systems were designed and optimized with the aim of providing precise, accurate and reliable flow methods for NAC determination in pharmaceuticals with very low sample and reagent consumption. Proposed methods are based on a redox reaction wherein NAC reduces a complex of Cu(II) and bathocuproine disulfonate (BCS) to orange [Cu(BCS)2]3– complex, which absorption was measured at λmax = 483 nm. The optimized FIA and SIA configuration yielded a linear calibration curve with correlation coefficients (R2 = 0.9999 and R2 = 0.9996) in the concentration range of 3.0 × 10–7 – 3.0 × 10–5 mol L–1 and analytical frequency of 120 h–1 for the FIA method and 4.0 × 10–7 – 4.0 × 10–5 mol L–1, at sampling rate 60 h–1 for the SIA method. The proposed flow methods were successfully applied for the determination of NAC in pharmaceutical products, as the results showed good agreement with the standard method prescribed by Pharmacopoeia. Recoveries were in the range from 98.4% to 101.9% for the FIA method and from 97.2% to 101.8% for the SIA method.

Rare study on quantitative relationship between energetic impact of debris flows on the intensity and duration of growth disturbances of tree rings was carried out, partly due to lack of feasible approaches and detailed field evidence. In this study, we firstly determine the age of a recent debris flow derived from historic landslide deposits at Qingyang mountain (QYM) on the northeastern Tibet plateau by dendrogeomorphic technique. We acquired the quantitative data of annual widths of tree rings in history and confirmed the influence of debris flow rather than other factors (e.g. climatic event and inset outbreaking) in disturbing the growth of tree rings in a specific year. Using the approach, we determined the age of the debris flow at QYM occurred in 1982, which was speculated to be triggered by high monthly precipitation of July in 1982. Subsequently, based on the boundaries of historic debris flow identified on remote sensing images before and after 1982 and depth-integrated continuum model, we reconstructed the process of 1982-debris flow and obtained the kinematic energy of debris flow impacting on the sampled trees. Based on the study, we observed that two growth disturbance patterns of tree rings influenced by the reconstructed 1982-debris flow were revealed including growth suppression and asymmetric growth. A raw logarithm relationship between duration (i.e. lasting time for the disturbed tree rings to recover the initial width) and intensity of growth disturbances (i.e. growth suppression ratio of disturbed tree rings) was obtained. We concluded that there is a negative exponential relationship between simulated kinematic energy of debris flow impacting on the disturbed trees and time to recover the initial width of corresponding tree rings.

Ultrasonography is a relevant diagnostic tool extensively used andrology of human and do-mestic animals, including dogs. The present review aimed to describe all the technologies based on ultrasound, starting with the basic B-Mode ultrasonography to the recent contrast-enhanced ultrasonography (CEUS) and the ultrasound elastography, available to assess the testicle of the dog. The principles of the different technologies and the relevant findings in normal and ab-normal testicular conditions were described and discussed. B-mode ultrasonography aims at the examination of the testis detecting focal lesions but lacks objectivization. Other technologies, such as Doppler ultrasonography, B-Flow, and CEUS allow the definition of vascular patterns, that could be measured with specific applications, such as spectral Doppler or quantitative CEUS. Finally, ultrasound elastography allows the estimation of parenchyma stiffness, in both qualitatively and quantitatively manner. Ultrasound-based technologies assist the andrology in the evaluation of the testicular function and integrity, offering valuable information to define pathological conditions that could have an impact on the health and life quality of the male dog.

This paper proposes a high-performance and low-cost in-flight collision avoidance system based on background subtraction for unmanned aerial vehicles (UAVs). The pipeline of proposed in-flight collision avoidance system is as follows: (i) dynamic background subtraction to remove the background and to detect moving objects, (ii) denoise using morphology and binarization methods, (iii) Euclidean clustering to cluster the moving object and to remove noise blobs, (iv) distinguish independent objects and track the movement using Kalman filter, and (v) collision avoidance using proposed decision-making techniques. This work focuses on the design and the demonstration of a vision-based fast moving object detection and tracking system with decision-making capabilities to perform evasive maneuvers to replace high vision system such as event camera. The development of high-performance, low-cost unmanned aerial vehicles paired with rapid progress in vision-based perception systems herald a new era of autonomous flight systems with mission-ready capabilities. One of the key features of an autonomous UAV is a robust mid-air collision avoidance strategy. The novelty of our method lies in the motion-compensating moving object detection framework, which accomplishes the task with background subtraction via 2-D transformation approximation. Clustering and tracking algorithms process detection data to track independent objects, and stereo-camera-based distance estimation is conducted to estimate the 3-D trajectory, which is then used during decision-making procedures. The examination of the system is conducted with a quadrotor UAV test vehicle, and appropriate algorithm parameters for various requirements are deduced.

Background. There are scant data about the effectiveness of high flow nasal cannula (HFNC) oxygen therapy in patients hospitalized with severe acute respiratory failure (ARF) in non-intensive medical wards, particularly regarding the effect on arterial oxygenation compared to conventional oxygen therapy (COT) and non-invasive ventilation (NIV) or continuous positive airway pressure (CPAP). Methods. In a retrospective observational study, oxygenation parameters were measured before and immediately after HFNC initiation in 37 consecutive patients hospitalized in a geriatric ward in 2017. Results. HFNC was used as escalation therapy for untreatable hypoxia after failure of NIV/CPAP (n=18) or COT (n=19). Twenty-two patients died, 2 were transferred to the intensive care unit, while 13 were discharged alive. A “do not intubate” status was identified in 17 of the 22 deceased patients. Partial pressure of oxygen (pO2, p< 0.0001), oxygen saturation (SO2, p< 0.0001), pO2/fraction of inspired oxygen ratio (p=0.004) and peripheral SO2 measured by pulse oximetry (p< 0.0001) significantly increased soon after HFNC application. Oxygenation improvements were greater after escalation from NIV/CPAP and in patients discharged alive. Conclusion. HFNC significantly improved oxygenation in severe ARF after failure of COT or NIV/CPAP and may be particularly suitable for older patients hospitalized in non-intensive medical wards.

This study aims to optimize the subway platform passenger flow guidance method using Anylogic simulation software. The objective of the study is to minimize overcrowding within subway carriages, enhance transportation capacity, and augment service levels by guiding passengers on the platform to board trains in a distributed manner. The study achieves a balanced flow of passengers in each carriage by taking into consideration the number of passengers in each carriage, the number of passengers at the station, and the expected number of passengers disembarking from the trains. The standard deviation of balance is used to optimize the subway platform passenger flow guidance method. We simulated Guangzhou Metro Zhujiang New Town Line 5 platform to compare different guidance methods and evaluate their effects on the uneven distribution of passengers with passenger flows ranging from 120K to 600K people per day. Our results show that guidance method 2, relative to manual guidance, improves by 38.5% under a daily passenger flow of 240K people on Zhujiang New Town Line 5. Guidance method 3 improves by 25.7% relative to guidance method 2 and by 54.4% relative to manual guidance.

The main problem in pursuing multiple extended targets tracking is distinguishing the origins of the measurements. The association of measurements to the possible origins within the target’s extent is difficult, especially for the occlusions or the detection blind zone which cause the intermittent measurements. To solve the problem, a hierarchical network-based tracklets data association algorithm is proposed. At the low level, the min cost network flow model is used to extract possible tracklets from the divided measurement set. At the high-level, the trajectories are estimated from the tracks produced by the previous low level network. The experimental results show that the hierarchical network-based tracklets data association algorithm outperforms the JPDA and RFS-based method when the measurement is intermittently unavailable.

In this work, an novel flow-electric field coupling configuration for enhanced Zn-Cd cementation was designed and utilized. A series of tests were conducted to explore the optimization of Zn-Cd cementation process and its mechanism.Firstly, the various characterisations of the cadmium sponge at different locations in the device were compared and it was concluded that the purity of the cadmium sponge was optimal from the anode surface. The generation and stripping of cadmium sponge was revealed for the first time by cross-sectional electron microscopy. The four stages of the apparent reaction in the system were analysed in relation to the pH, cadmium concentration and cadmium sponge flaking at each flow rate. It was proved that the separation of cadmium sponge mainly occurred in the third phase. Secondly, by comparing the morphology and specific surface area of cadmium sheep at different flow rates, the optimum flow field velocity was identified as 30 ml/s. Six flow field configurations were compared and preferred. The results demonstrate that the LCAH modulation results in a more sparse structure of the cadmium sponge, which is more easily exfoliated from the zinc anode surface by fluid impact. This was considered to be the most beneficial flow field configuration for improving the cadmium cementation rate and reducing the cost of the reaction. Further, the reaction steps of the system were analysed. The diffusion process under different flow field configurations was confirmed by calculations to follow first order kinetics. The diffusion coefficient of LACH proved to be the highest in the comparative tests and this result was also supported by the apparent experimental results.

The aim of this study was to verify the effects of blood flow restriction on movement velocity and muscle activity during the back-squat exercise. Methods: Twenty-four university students participated in this study. In two randomized 72-hours apart sessions, participants performed a 4-set protocol consisting of 30-15-15-15 repetitions performed at 30% of their one-repetition maximum in the back-squat exercise. In both sessions, neuromuscular function was monitored by surface electromyography (EMG) and movement velocity (mean propulsive velocity [MPV], peak concentric velocity [Vmax] and the effort index [EI]). Blood flow restriction (BFR) was applied during exercise in one of the experimental sessions with 80% of full arterial occlusion pressure over lower limbs. Results: BFR condition showed higher (p&lt;0.05) EI, peak and rooted mean square normalized EMG in set 1 compared to set 2. Similar MPV and Vmax were observed at each set for both BFR and control conditions. No significant differences were observed between conditions at any set. Conclusions: BFR did not imply changes in neuromuscular performance during low-intensity resistance training, but it might induce greater intra-series velocity loss and less activation of the muscles involved.

This study seeks to determine how economic policy uncertainty (EPU) influences investment decisions and the market value of the Pakistan Stock Exchange. The study examines investment and operational data from 249 energy and petroleum companies between 2015 and 2020, in addition to macroeconomic variables such as EPU. This study investigates the moderating effects of EPU on investments in fixed and intangible assets, as well as its effect on Tobin's Q and the market price per share. The outcomes demonstrate that EPU reduces the costs of both tangible and intangible assets for businesses. In addition, companies with a greater Tobin's Q and market price per share are more impacted by uncertain corporate investment policies. However, financial leverage is found to be negatively correlated with share price and positively correlated with earnings per share and earnings per unit. Tobin's Q is positively correlated with financial leverage, indicating that firms that raise capital through debt are more likely to create value for investors. The research indicates that market-dependent enterprises are more susceptible to the unpredictability of monetary policy. Eventually, the findings suggest that consistent and transparent economic policies may increase the efficiency of corporate investment.

Background and Objectives: Ultrasound (US) is a non-invasive tool for the in-vivo detection of peripheral nerve alterations. Materials and Methods: In this study we applied nerve US to assist the discrimination between the spectrum of Amyotrophic Lateral Sclerosis (ALS, n=11), chronic inflammatory demyelinating polyradiculoneuropathy (CIDP, n=5) and genetically confirmed Charcot-Marie-Tooth disease (CMT, n=5). All participants and n=15 controls without neurological diseases underwent high-resolution US of the bilateral tibial nerve. Nerve cross-sectional area (CSA) and nerve microvascular blood flow were compared between the groups and related to cerebrospinal fluid (CSF) measures, clinical symptoms and nerve conduction studies. Analyses are part of a larger multimodal study on the comparison between US and 7 Tesla (T) magnetic resonance neurography (MRN). Results: Patients and controls were matched with respect to their demographical data. CMT had the longest disease duration, followed by CIDP and ALS. CSA was related to age, weight and disease duration. CSA was larger in CMT and CIDP compared to ALS and controls. Blood flow was greatest in CIDP, and higher than in CMT, ALS and controls. In ALS, greater CSA was correlated with greater CSF total protein and higher albumin quotient. US measures did not correlate with clinical scores or nerve conduction studies in any of the subgroups. Conclusion: Our results point towards the feasibility of CSA and blood flow to discriminate between ALS, CIDP and CMT, even in small sample sized groups. In ALS, larger CSA could indicate an inflammatory disease subtype characterized by reduced blood-nerve barrier integrity. Our upcoming analysis will focus on the additive value of 7T MRN in combination with US to disentangle the spectrum between more inflammatory or more degenerative disease variants along the disease groups.

Future climate change is expected to affect components of the hydrological cycle. However geologic factors can sometimes be more important than the climate with regarding to change hydrological processes. The Keriya River is a large glacier-fed river in the western Tibet Plateau, its upper reaches flow across active fault zones, which have experienced four medium-sized earthquakes within four months 1974. These active faults have made difficult to identify normal meltwater changes using a snow-ice melt model. Because of the seismic events, the river has experienced substantial changes in their drainage systems and complex hydrological processes. Both the Mann-Kendall trend test and a correlation analysis were applied to detect the monthly patterns of stream flows, the change points and the correlations among both summer discharge and air temperature before and after seismic events. We found significant correlations between monthly air temperature and meltwater flow in the summer June during the pre-earthquake of 1958-1974, but none in July and August in the post-earthquake of 1975-1980, and we found no correlation following the earthquake. The correlations were the inverse by losing the former and setting up the latter alternately since the multiple earthquakes. Clearly, the earthquakes and changes in the faults can greatly induce hydrological processes.

Keeping the bus voltage within acceptable limits depends on dispatching reactive power. Power quality improves as a result of creating an effective power flow system, which also helps to reduce power loss. Therefore, Optimal Reactive Power Dispatch (ORPD) studies aim at designing appropriate system configurations to enable a reliable operation of power systems. Establishment of such a configuration is handled through control variables in power systems. On the other hand, installing Distributed Generation Unit (DGU) into a power system can have an important effect on power quality and power loss minimization. In this paper, Grey Wolf Optimization (GWO method is applied to ORPD problem for the first time, to find optimal placement of newly installed DGUs at the power system. Active power loss and voltage minimization have been minimized by optimizing the control variables while keeping them within their upper and lower bounds, and by finding the optimal placement of a newly installed DGU in power system. On the basis of IEEE 30 bus and IEEE 118 bus systems, performance of the suggested approach is investigated. A comparison is also performed among the proposed method and some other methods. Test results demonstrate that the resulting configuration contributes to growing the rate of renewable integration to a power system. The results also indicate that the suggested optimization approach applied to ORPD problem has improved power system performance in terms of both on power loss and voltage deviation. The promising results highlight the potential of the GWO algorithm to facilitate the integration of renewable power sources, and its role in promoting sustainable energy solutions.

Gastric cancer (GC) is the third leading cause of cancer-related deaths worldwide. GC with peritoneal metastasis exhibits a poor prognosis due to the lack of diagnostic biomarkers and effective therapy. A comprehensive analysis of malignant ascites identified the genomic alterations and significant amplifications of cancer driver genes, including CD44. CD44 and its splicing variants are overexpressed in tumors, and play crucial roles in the acquisition of invasiveness, stemness, and resistance to treatments. Therefore, the development of CD44-targeting monoclonal antibodies (mAbs) is important for GC diagnosis and therapy. In this study, we immunized mice with CD44v3–10-overexpressed PANC-1 cells and established several dozens of clones that produce anti-CD44v3–10 mAbs. One of the clones (C44Mab-94; IgG1, kappa) recognized the variant-8-encoded region and peptide, indicating that C44Mab-94 is a specific mAb for CD44v8. Furthermore, C44Mab-94 could recognize CHO/CD44v3–10 cells, oral squamous cell carcinoma cell line (HSC-3), or GC cell lines (MKN45 and NUGC-4) in flow cytometric analyses. C44Mab-94 could detect the exogenous CD44v3–10 and endogenous CD44v8 in western blotting and stained the formalin-fixed paraffin-embedded gastric cancer cells in immunohistochemistry. These results indicate that C44Mab-94 is useful for detecting CD44v8 in various applications and is expected to be useful for the application of GC diagnosis and therapy.

The survey findings reveal that rivers worldwide carry an annual sediment load of 15 billion tons into the sea, and the Yellow River basin alone contributes 1.6 billion tons of sand. Therefore, understanding the science of wind and sand in the Yellow River is crucial to ensuring the safe development of similar basins across China and the world. This study examines the midstream wind and sand area of the Xiliugou tributary, a part of the upper Yellow River. The researchers used a stepped sand collector combined with an anemometer to measure the sand transport flux at 0-50 cm height on various underlying surfaces of the basin. Then, they estimated the amount of wind and sand entering the Yellow River using a function model based on the measured factors. Furthermore, the team analyzed the particle size composition of wind-eroded sand to better understand the principles of wind and sand erosion and accumulation in the basin. The results of the study show that the sand transport flux per unit area varies significantly across different underlying surfaces. Moreover, the contribution of moving sandy land, semi-fixed sand, and fixed sand to wind and sand deposition in the Yellow River basin was 77.08%, 15.30%, and 7.62%, respectively. The vertical change of sand transport rate on the basin's surface demonstrates that the total sand transport rate is an exponential function of wind speed. Based on this relationship, the researchers estimated that the total annual average wind and sand entering the Yellow River basin via the Xiliugou tributary is approximately 8.09×105t. Due to the basin's unique geography and sand source, the particle size composition of wind-eroded sand differs between the east and west sides of the river channel. On the west side, desert sand, mainly fine sand, and very fine sand constitutes the sand source. Conversely, on the east side, sand collected in the riverbed by secondary wind erosion is the primary sand source. Furthermore, human activities have disturbed the grain composition, mainly comprising powder and clay particles. This phenomenon, known as "wind-blown mud and water-washed sand," is evident in this geographical unit. In conclusion, the Yellow River basin still faces significant ecological security hazards. Understanding the coupling relationship between desert-basin-sand and wind is the foundation for effectively controlling wind and sand flow into the Yellow River basin.

This study investigates the Hagen–Poiseuille pipe flow of viscoplastic fluids, focusing on analytical predictions of concrete pumping using the shear-stress-dependent parabolic model. Research highlights encompass solving the steady laminar pipe flow for viscoplastic fluids described by the parabolic model, extending analytical studies to a nonlinear rheological model with easily accessible experimental parameters, presenting detailed results for the two-fluid parabolic model, and introducing computational apps implementing theoretical findings. The parabolic model outperforms linear models, such as the Bingham model, in accuracy by accounting for the nonlinearity in the shear stress and shear rate relations. The influence of rheological parameters on these relations is analyzed, and their versatility is demonstrated by a Wolfram Mathematica-based application program. This approach is adaptable for other models with shear stress as the independent variable, offering valuable insights into viscoplastic fluid flows.

We propose an algorithm for generating a panoramic image of a pipe’s inner surface based on inverse perspective mapping (IPM). For efficient crack detection, we used only perspective images of the pipe interior that can be obtained with a single lens camera instead of those taken with a 360-degree camera or a 3D depth camera. Frontal images taken while passing through the pipe were converted to images of the inner surface of the pipe using IPM. We derived a generalized IPM formula that considers the slope of the image plane to correct image distortion caused by the tilt of the plane; this IPM formula was derived based on the vanishing point of the perspective image, which was detected using optical flow techniques. Finally, the multiple transformed images with overlapping areas were combined via image stitching to create a panoramic image of the inner pipe surface. To validate our proposed algorithm, we restored images of pipe inner surface using a 3D pipe model and used these images for crack detection.

This work is related to the environmental toxicology risk assessment and evaluation of possible transformation of carbon-based nanomaterials (CNMs) after the contact with marine microalgae. The materials used in the study represent common and widely applied multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO). The toxicity was evaluated as growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species generation changes. The measurement was performed with flow cytometry after 3, 24, 96 h, and 7 days. Biotransformation of nanomaterials were evaluated after 7 days of microalgae cultivation with CNMs by FTIR and Raman spectroscopy. The calculated toxic level (EC50 in mg/L, 96 h) of ued CNMs reduced in the following order: CNTs (18.98) &gt; GrO (76.77) &gt; Gr (159.40) &gt; C60 (414.0). Oxidative stress and membrane depolarization was the main toxic action of CNTs and GrO. At the same time, Gr and C60 decreased the toxic action with time and had no negative impact on microalgae even at concentration of 125 mg/L. Moreover, C60 and Gr after seven days of the contact with microalgae cells obtained structural deformations.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs &gt; GrO &gt; Gr &gt; C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

In the current study, we assessed the effects of conventional and Ultra High Dose Rate (UHDR) irradiation on behavioral and cognitive performance one month following exposure and assessed whether these effects were associated with alterations in the number of immune cells in the hippocampus using flow cytometry. Conventional- and UHDR-irradiated mice showed impaired novel object recognition. During fear learning, conventional- and UHDR-irradiated mice moved less during the inter-stimulus-interval (ISI) and UHDR-irradiated mice also moved less during the baseline period (prior to the first tone). In irradiated mice, reduced activity levels were also seen in the home cage; conventional- and UHDR-irradiated mice moved less during the light period and UHDR-irradiated mice moved less during the dark period. Following behavioral and cognitive testing, infiltrating immune cells in the hippocampus were analyzed by flow cytometry. The percent Ly6G+ CD45+ cells in the hippocampus was lower in conventional- and UHDR-irradiated than sham-irradiated mice, suggesting that neutrophils might be particularly sensitive to radiation. The percent of Ly6G+ CD45+ cells in the hippocampus was positively correlated with the time spent exploring the novel object in the object recognition test, suggesting that the reduced percent Ly6G+ CD45+ cells in the hippocampus might mediate some of the detrimental radiation-induced cognitive effects.

Rapid, accurate, and convenient diagnosis is essential for effective disease management. Various detection methods, such as enzyme-linked immunosorbent assay, have been extensively used, with lateral flow immunoassay (LFIA) recently emerging as a major diagnostic tool. Nanoparticles (NPs) with characteristic optical properties are used as probes for LFIA, and researchers have presented various types of optical NPs with modified optical properties. Herein, we review literature on LFIA with optical NPs for the detection of specific targets in the context of diagnostics.

Intersections within urban centers do not allow all citizens to move in a fluid manner. In this sense, this paper proposes a queuing network model based on Kendall's notation for the intersection of two urban streets (East 53rd Street and East 56th Street) in Panama City. A set of traffic lights operating under a fixed time scheme controls the vehicular flow at the intersection. The objective is to optimize the vehicular flow at the intersection by minimizing the waiting time of the vehicles using mathematical models, Linear Regressor Model, and simulations performed in MATLAB evaluating the waiting time experienced by the vehicles. Based on the results obtained, the optimal signal timing of the traffic lights is determined to minimize the waiting time for both streets.

The local reactive power control in distribution grids with a high penetration of distributed energy resources (DERs) is essential in future power system operation. Appropriate control characteristic curves for DERs support stable and efficient distribution grid operation. However, the current practice is to configure local controllers collectively with constant characteristic curves that may not be efficient for volatile grid conditions or the desired targets of grid operators. To address this issue, this paper proposes a time series optimization-based method to calculate control parameters, which enables each DER to be independently controlled by an exclusive characteristic curve for optimizing its reactive power provision. To realize time series optimizations, the open-source tools pandapower and PowerModels are interconnected functionally. Based on the optimization results, Q(V)- and Q(P)-characteristic curves can be individually calculated using the linear decision tree regression to support voltage stability and provide reactive power flexibility and potentially reduce grid losses and component loadings. In this paper, the newly calculated characteristic curves are applied in two representative case studies, and the results demonstrate that the proposed method outperforms the reference ones suggested by grid codes.

Blood flow-restricted training (BFR) is constantly growing in popularity. Despite growing evidence of the significant influence of BFR training on different body functions, its impact on the vascular system, especially the arteries, is controversial. Therefore, the objective of our study was to analyze how BFR exercise, compared to other types of exercise without restriction of blood flow or other active intervention, influences arterial functions and angiogenesis in adults. Studies comparing the effect of BFR versus non-BFR training on arterial parameters are divided into three categories. Endothelial function, angiogenesis, and other vasculature functions. The search was based on three databases (Cochrane Library, PubMed®, Embase). In this systematic review, 38 studies were included. Meta-analysis revealed a more significant improvement in flow-mediated dilatation (FMD) (p=0.002) and the production of the primary angiogenesis biomarker Vascular Endothelial Growth Factor (VEGF) (p=0.009) after training in BFR compared to nonBFR (p=0.002). Analysis of pulse wave velocity, ankle-brachial index, systolic blood pressure, or heart rate did not show a significant difference in changes between BFR and non-BFR training. Other parameters examined were not sufficiently provided to be included in the meta-analysis. The results obtained, present trends suggesting the significant impact of BFR training on endothelial functions and angiogenesis. Unfortunately, there is still a lack of multicenter randomized clinical trials, including many participants, that are necessary to confirm the advantage of BFR over non-BFR activity.

Cryptococcosis is one of the most serious opportunistic diseases in patients living with HIV. For this reason, it is important to have early diagnosis and appropriate treatment. Objectives. The aim of the study was to know the evolution of patients diagnosed with cryptococcosis by detection of Cryptococcus antigen in serum by lateral flow (CrAg LFA) without nervous system involvement and with treatment in accordance with the results. Materials and Methods. A retrospective, longitudinal, analytical study was performed. Seventy patients with cryptococcosis initially diagnosed by serum CrAg LFA without meningeal involvement between January 2019 and April 2022 were analyzed for medical records. The treatment regimen was adapted to the results of blood culture, respiratory material or pulmonary tomography imaging. Results. Seventy patients were included, 13 had probable pulmonary cryptococcosis, 4 had proven pulmonary cryptococcosis, 3 had fungemia and 50 had pre-emptive therapy without microbiological or imaging findings compatible with cryptococcosis. Among the 50 patients with pre-emptive therapy, none had meningeal involvement or cryptococcosis recurrences to date. Conclusion. Pre-emptive therapy avoided progression to meningitis in patients with CrAg LFA-positive patients. Pre-emptive therapy with dose adjustment of fluconazole in patients with the mentioned characteristics was useful despite the use of lower doses than recommended.

The compilation summarizes results so far gathered in a project that investigates the atom with classical (Newtonian) physics. It posits that the atom’s wave-particle dual nature is real, objective and intrinsic; the wave gives rise to the cosmic vacuum field while the particle, of course, manifests condensed matter. Light’s π radians oscillation manifests, on molar scale, significant radial tension in the vacuum field, the effect, amongst others, causes molecular matter to precipitate out of the vacuum – so-called ‘molecular outflow’. Cosmic vacuum field radial tension relates to molecular mass, in other words, a mass-radius (M-R) relationship is uncovered. It is argued that using the M-R relation it is possible to perform a valid simulation of the cosmic physical reality. The three states of matter are meaningfully accounted for using the atom’s e-m radiation wavelength. It is explained that force, be it of any kind whatsoever, originates in the atomic waveform, i.e., the cosmic vacuum field.

Calibration of flow devices is important in several areas of pharmaceutical, flow chemistry and microfluidic applications where dosage of process liquids or accurate measurement of the flow rate is important. The process-oriented liquid itself might influence the performance of the flow device and the simultaneous determination of the dynamic viscosity under flow conditions might be a valuable information for the process parameters. To offer the simultaneous calibration of the dynamic viscosity of the process-oriented liquid at the corresponding flowrate, METAS has built a pipe viscometer for the traceable in-line measurement of the dynamic viscosity in the current flow facilities for low flow rates from 1 L/min to 150 mL/min and pressure drops up to 10 bar. The traceability of all the measuring quantities as well as the geometrical dimensions of the micro tube guarantee the traceability of the pipe viscometer to SI units. The most challenging part is the traceable determination of the inner diameter of the micro tube. This can be achieved by measuring the pressure drop as a function of flow rate with the pipe viscometer and applying the law of Hagen-Poiseuille with a traceable dynamic viscosity of a reference liquid (water) or perform the measurements with the micro-CT at METAS, which determines the inner diameter by x-ray diffraction. The validation of the stated measurement uncertainty of the pipe viscometer has been performed by means of calibration of the dynamic viscosity of several reference liquids with traceable density and kinematic viscosity. The setup of the facility, the traceability as well as the uncertainty calculation of the pipe viscometer for the in-line measurement of the dynamic viscosity are discussed in this paper.

The growing integration of renewable energy sources (RES) into the power system causes congestion to occur more frequently. In order to reduce congestion in the short term and to make the utilization of the power system more efficient in the long term, power flow control (PFC) in the transmission system has been proposed. However, exemplary studies show that congestion will increase also in the distribution system if the transmission system is expanded. For this reason, the potential of PFC to reduce congestion in a model of a real 110 kV distribution system is investigated. Several Unified Power Flow Controller (UPFC) devices are optimized in terms of their number and placement in the power system, their size, control parameters, and costs, by using a Parallel Tempering approach as well as a greedy algorithm. Two optimization variants are considered, one reducing the number of degrees of freedom by integrating system knowledge while the other is not. We find that near a critical grid state and disregarding costs, PFC can reduce congestion significantly (99.13 %). When costs of the UPFCs are taken into account, PFC can reduce congestion by 73.2 %. A basic economic analysis of the costs reveals that the usage of UPFCs is profitable. Furthermore, it is found that the reduction of the solution space of the optimization problem leads to better results faster and that, contrary to expectations, the optimization problem is simple to solve. The developed methods allow not only for the determination of the optimal use of UPFCs to minimize congestion, but also to estimate their profitability.

Small hydro-power systems seem to be the best solution for energy generation through the use of pump as turbine (PAT) due to its low cost and lesser environmental hazards associated with it. Recently, PAT applications are gaining global attention in energy generation but its operation is not fully understood. The performance and flow behavior is affected by several operational conditions. This study seeks to investigate the effects of rotational speed on flow behavior and performance of a PAT. Rotational speed is an important physical parameter that affects the operation of a PAT. A selected centrifugal pump model of four blades and splitters was used for the study. Numerical simulations were carried out using k-ε turbulence model to solve the three-dimensional (3D) equations in both pump and PAT modes. The outcomes were then validated using experimental results in the pump mode to obtain overview flow physiognomies. The results predicted that the efficiency increases as the rotational speed increases in the pump mode whereas in turbine mode, higher rotational speed cannot convert hydraulic energy into mechanical energy. Thus, a rotational speed of 1500 rpm performed the highest efficiency of 69.8% at QBEP among the other rotational speeds selected. Moreover, the head performance in the turbine mode increases as the flow rate increases. This research provides useful information which will help improve PAT performance as well as selecting PAT for small hydro-power site.

Smartphone-based point-of-care testing (POCT) is rapidly emerging as an alternative to traditional screening and laboratory testing, particularly in resource-limited settings. In this proof-of-concept study, we present a smartphone- and cloud-based artificial intelligence quantitative analysis system (SCAISY) for relative quantification of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2)-specific IgG antibody lateral flow assays that enables rapid and accurate evaluation of test strips. By capturing an image with a smartphone camera, SCAISY quantitatively analyzes antibody levels and provides results to the user. We analyzed changes in antibody levels over time in over 248 individuals, including vaccine type, number of doses, and infection status, with a standard deviation of less than 10%. We also tracked antibody levels in six participants before and after SARS-CoV-2 infection. Finally, we examined the effects of lighting conditions, camera angle, and smartphone type to ensure consistency and reproducibility. This study suggests that SCAISY is a simple and powerful tool for real-time public health surveillance, enabling the acceleration of quantifying SARS-CoV-2-specific antibodies generated by either vaccination or infection and tracking of personal immunity levels.

Acute pancreatitis (AP) is the most common gastrointestinal disease leading to hospitalizations. The development of AP leads to damage of the pancreatic microcirculation with a cascade of subsequent events resulting, among others, in coagulopathy. Previous research showed that anticoagulants can be an important therapeutic agent. Heparin and acenocoumarol can alleviate the course of AP, as well as accelerate healing and post-inflammatory regeneration of the pancreas. The aim of this study was to check whether warfarin, a drug with more stable effects than acenocoumarol, affects the healing and regeneration of the pancreas in the cerulein-induced AP. AP was evoked in Wistar male rats by intraperitoneal administration of cerulein. The first dose of warfarin (45, 90 or 180 µg/kg/dose) was administered 24 hours after the first dose of cerulein and the doses of warfarin were repeated once a day in subsequent 10 days. The severity of acute pancreatitis was assessed immediately after the last dose of cerulein, as well as 1, 2, 3, 5, and 10 days after AP induction. Treatment with warfarin dose-dependently increased interna-tional normalized ratio (INR) and attenuated the severity of pancreatitis in histological ex-amination and accelerated pancreatic recovery. Those effects were accompanied with a faster reduction in the pancreatitis-evoked increase in serum activity of amylase and lipase, serum concentration of pro-inflammatory interleukin-1β, and plasma level of D-Dimer. In addition, treatment with warfarin decreased pancreatic weight and improved pancreatic blood flow in rats with AP. The therapeutic effect was particularly pronounced after the administration of warfarin at a dose of 90 µg/kg/dose. Conclusion: Administration of warfarin accelerates re-generation of the pancreas and recovery in the course of cerulein-induced mild-edematous acute pancreatitis.

It was recently shown that urban networks might exhibit two different critical points, one for the percolation of congested links through the network, and another one for the flow of vehicles through the network. It was observed that the percolation critical point happens after the flow critical point, where network throughput is maximized. This result is important because if a causal relationship exists between these two processes, it can be leveraged for improving control methods to avoid network collapse. This paper presents the results of numerical experiments to understand the possible causal relationship between the percolation and flow processes by focusing on the relative timing between the two critical points. The goal is to understand the impacts of important factors such as: (i) urban network type: long- and short-block networks, (ii) signal timing control type: fixed, random, responsive, and (iii) route choice: turning proportions at intersections. We find that the threshold density $k^*_c$ to determine if a link is congested has the main impact on the timing of the percolation transition, where lower values trigger earlier transitions. This implies that $k^*_c$ can be set such that the percolation transition happens before the flow critical point, opening the door for improved congestion management strategies. If $k^*_c$ is set to the average network critical density, maximum network throughput happen simultaneously with the percolation transition. Surprisingly, it appears that these results, and more generally, the relationship between the percolation and flow processes is independent of (i) and (ii) above.

Malignancy is a fatal disease with an increasing incidence with each passing year, and the early diagnosis of malignancy can significantly improve the cure rate of patients, which has profound implications for saving patients' lives. The changes of miRNA are closely related to the occurrence of malignant tumors. The expression of miRNA in many malignant tumors is obviously different and unique from that in normal tissues. In this study, a strategy for amplifying microRNA (miRNA) signal was designed using duplex specific nuclease (DSN), which was then combined with Peptide nucleic acid (PNA) probe hybridization technology to prepare a sensitive and efficient paper-based lateral flow biosensor (LFB) for the detection of pancreatic cancer (PC) associated microRNA-10b. The performance evaluation results of the LFB showed that the detection limit of miR-NA-10b is 5 nM/mL, and carries demonstrated well specificity, stability, reproducibility. The biosensor prepared in this paper can provide accurate and rapid detection of miRNA-10b. The detection results play a guiding role in the early diagnosis of PC. Meeting the clinical need for largescale screening of individuals at high risk of PC. Providing new avenues to achieve early mass screening in individuals at high risk of PC.

Cluster of differentiation 44 (CD44) promotes tumor progression through the recruitment of growth factors, and the acquisition of stemness, invasiveness, and drug resistance. CD44 has multiple isoforms including CD44 standard (CD44s) and CD44 variants (CD44v), which have common and unique functions in tumor development. Therefore, the elucidation of each CD44 isoform’s function in tumor is essential for the establishment of CD44-targeting tumor therapy. We have established various anti-CD44s and anti-CD44v monoclonal antibodies (mAbs) through immunization of CD44v3–10-overexpressed cells. In this study, we established C44Mab-6 (IgG1, kappa), which recognized the CD44 variant 3-encoded region (CD44v3) determined by enzyme-linked immunosorbent assay. C44Mab-6 reacted with CD44v3–10-overexpressed Chinese hamster ovary (CHO)-K1 cells (CHO/CD44v3–10) or some cancer cell lines (COLO205 and HSC-3) by flow cytometry. The apparent KD of C44Mab-6 for CHO/CD44v3–10, COLO205, and HSC-3 was 1.5 × 10−9 M, 6.3 × 10−9 M, and 1.9 × 10−9 M, respectively. C44Mab-6 could detect the CD44v3–10 in western blotting, and stained the formalin-fixed paraffin-embedded tumor sections in immunohistochemistry. These results indicate that C44Mab-6 is useful for detecting CD44v3 in various experiments, and expected for the application of tumor diagnosis and therapy.

In a power plant that uses seawater as a coolant, a debris filter is required to remove foreign substances from the seawater, and differential pressure leads to a decrease in the coolant flow rate, leading to a decrease in power generation efficiency. In this study, analysis was performed under different initial flow velocity conditions of 1.5m/s, 2.0m/s, and 2.5m/s for a debris filter used in a power plant to understand flow characteristics in CTCS. The flow and differential pressure characteristics of a CTCS with an installed debris filter were considered in a comparative analysis of velocity, pressure, and turbulent kinetic energy distribution. The results confirmed that a vortex was generated in the pipe with the debris filter, apparently due to the collision of the flow with the bracket of the debris filter. As the flow rate increased, the range of the vortex increased, causing a loss in flow.

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

Marangoni flow in foam fractionation in the lamellar film for the interior and exterior of a micro-foam was investigated. The three-dimensional node-film-Plateau Border system was modeled using computational fluid dynamics. The importance of the surfactant concentration of the foam fractionation column and air-liquid interface mobility on the Marangoni velocity in the film was emphasized. The study found that an increase in surfactant concentration in the reflux column significantly increases the Marangoni velocities. Additionally, a mobile interface results in a higher Marangoni flow, while a rigid interface leads to less intensive flow. The behavior of the Marangoni flow in both interior and exterior foam was explored, revealing that the flow in exterior foam has different behavior due to the presence of the wall, which reduces the Marangoni velocity compared to interior films.

Breaching and liquefaction are two types of coastal flow slides proposed in the literature. While their final results are similar, liquefaction and breaching failure are two different processes, with breaching failure characterized by a different progression and sand movement mechanisms. In densely packed sand, breaching causes delayed sand grain discharge and negative excess pore pressures. Liquefaction, when a mass of soil suddenly behaves like a liquid, flow out over overly gentle slopes. Flow slides typically go unnoticed until the slope fails above ground because they start below the water. Without modern technology, diving equipment, risk assessment, and probabilistic and sensitivity assessments, flow slides inherently challenging. The authors developed a new sensitivity index to detect the susceptibility of coastal flow slides. It was established a sophisticated hybrid model that accommodates flow slides in sync with unpredictable variables employed in this new sensitivity index. Innovative hybrid model has three distinctive models. The Hybrid Hydrodynamic Model addresses wave, wind, current, climate change, and sediment transfer. The Monte Carlo Simulation analyses sensitivity, and the Bayesian Network calculates joint probability of coastal flow slide parameters of this new index that includes environmental characteristics, including climate change. With the assistance of these three models, researchers aim at a) presenting a methodology for coupling coastal flow slide projections with outcomes; b) distinguishing two flow slides; c) examining variables influencing flow slides. The use of such a hybrid model and risk index offers a robust and computationally efficient approach to evaluating the critical angle slope for breaching failure.

CC chemokine receptor 6 (CCR6) is a member of the G protein-coupled receptor (GPCR) family that is highly expressed in B lymphocytes, effector and memory T cells, regulatory T cells, and immature dendritic cells. CCR6 has been revealed to have important functions in many pathological conditions, such as cancer, intestinal bowel disease, psoriasis, and autoimmune diseases. The only CCR6 chemokine ligand, CC motif chemokine ligand 20 (CCL20), is also involved in pathogenesis by interacting with CCR6. The CCL20/CCR6 axis is drawing attention as an attractive therapeutic target for various diseases. In this study, we developed novel monoclonal antibodies (mAbs) against human CCR6 (hCCR6) using the peptide immunization method, which are applicable to flow cytometry and immunohistochemistry. The established anti-hCCR6 mAb, clone C6Mab-19 (mouse IgG1, kappa), reacted with hCCR6-overexpressed Chinese hamster ovary-K1 (CHO/hCCR6), HepG2 (human liver carcinoma), and HuH-7 (human differentiated hepatoma) cells in flow cytometry. The dissociation constant (KD) of C6Mab-19 was determined as 3.0 × 10−10 M for CHO/hCCR6, 6.9 × 10−10 M for HepG2, and 1.8 × 10−10 M for HuH-7. Thus, C6Mab-19 could bind to exogenously and endogenously expressed hCCR6 with extremely high affinity. Furthermore, C6Mab-19 could stain formalin-fixed paraffin-embedded lymph node tissues from a patient with non-Hodgkin lymphoma by immunohistochemistry. Therefore, C6Mab-19 is suitable for detecting hCCR6-expressing cells and tissues, and could be useful for pathological analysis and diagnosis.

An exact solution for the Nagel-Schreckenberg model for v_max = 1 is known since the 90s, yet for v_max > 1 it remains an open question. It is conjectured here that this general solution can be generated from the basic solution (for v_max = 1) by a linear coordinate transformation, the shear mapping, which requires no additional parameters in the deterministic case, and two additional parameters otherwise. The proposed solutions show remarkable agreement with existing numerical solutions, except in the congested regime where the Monte Carlo data shows more concavity than the more linear congested branches predicted by the theory. More research is needed to investigate this bias.

Abstract: Background: The diagnosis of nasal airway disorders relies on questionnaires, subjective data, and objective data. Interpretation of objective data obtained from measurement technology is not well understood by providers and researchers who use the equipment to test nasal airway function, justifying the need to cre-ate a new clinical tool. The Davidson Airway Function & Nasal Evaluation (DAFNE) Scoring System is a web-based scoring system that allows healthcare providers (MDs, PAs, PTs, APRNs, DMDs, DDSs, SLPs, and DCs) and researchers who treat nasal obstruction and breathing disorders to make more accurate diagnostic decisions, select the appropriate treatment for individualized patient care, monitor treatment progression and outcomes, and show how to approach a collaborative care model with other healthcare professionals. The current technologies, such as 4-phase rhinomanometry, use a simple approach that relies on a measurement tracing intersecting a color-coded y-axis on a four-quadrant graph with diagnostic numeric data output de-scribing nasal airflow and resistance. This is a good source of biofeedback demonstrating abnormal nasal breathing patterns but lacks interpretation guidelines to describe the severity of disease. The more sophisti-cated proprietary DAFNE approach uses multiple parameters which include airflow restriction, speed, vol-ume, and patient characteristics to identify patients’ disease progression much more accurately. Additionally, it explains how to segregate patients into appropriate treatment options which minimizes risks and compli-cations associated with sleep and breathing disorders while improving patient outcomes. Methods: Electronic searches of PubMed, MEDLINE, EMBASE Cochrane Library, and Scopus of publications between 1988-2022 were necessary to identify studies which determined the ranges of nasal function measurement parameters among three airway measurement technologies used in writing the DAFNE Score algorithm. The performance of DAFNE was evaluated compared to the research data and patient demographics used in previous studies. Results: By using primary outcome measurements from the literature, we were able to create a reliable, re-peatable, and validated tool to facilitate patient identification, treatment stratification, and collaboration for sleep and nasal breathing dysfunction. Subsequently, we found DAFNE could be used to identify the appro-priateness of a sleep study. Conclusions: DAFNE Scoring System has demonstrated the ability to detect high risk patients in the pediatric and adult populations susceptible of sleep apnea and breathing dysfunction needing a sleep study and treatment to improve nasal airway function and sleep. DAFNE Scoring System should be used as an adjunct tool in routine clinical practice and research to further understand the technol-ogy data output, identify patients at risk, stratify treatment options, progress, and stabilization after treatment, and how to collaborate with other healthcare providers to improve patient outcomes.

Cluster of differentiation 44 (CD44) has been investigated as a cancer stem cell (CSC) marker, and plays critical roles in tumor malignant progression. The splicing variants are overexpressed in many carcinomas, especially squamous cell carcinomas, and play critical roles in the promotion of tumor metastasis, the acquisition of CSC properties, and resistance to treatments. Therefore, each CD44 variant (CD44v) function and distribution in carcinomas should be clarified for the establishment of novel tumor diagnosis and therapy. In this study, we immunized mice with a CD44 variant (CD44v3−10) ectodomain and established various anti-CD44 monoclonal antibodies (mAbs). One of the established clones (C44Mab-34; IgG1, kappa) recognized a peptide which covers both variant 7 and 8-encoded region, indicating that C44Mab-34 is a specific mAb for CD44v7/8. Moreover, C44Mab-34 reacted with CD44v3–10-overexpressed Chinese hamster ovary-K1 (CHO) cells or oral squamous cell carcinoma (OSCC) cell line (HSC-3) by flow cytometry. The apparent KD of C44Mab-34 for CHO/CD44v3–10 and HSC-3 was 1.4 × 10−9 M and 3.2 × 10−9 M, respectively. C44Mab-34 could detect CD44v3–10 in western blotting, and stained the formalin-fixed paraffin-embedded OSCC in immunohistochemistry. These results indicate that C44Mab-34 is useful for detecting CD44v7/8 in various applications, and expected for the application of OSCC diagnosis and therapy.

Animal models of diseases in particular, the mice, are considered to be the cornerstone for translational research in immunology. The aim of the present study is to model the geometry and analyze the network structure of murine lymphatic system (LS). The algorithm for building the graph model of the LS makes use of anatomical data. To identify the edge directions of the graph model, a mass balance approach to lymph dynamics based on Hagen-Poiseuille equation is applied. It is the first study in which a geometric model of the murine LS has been developed and characterized in terms of its structural organization and the lymph transfer function. Our study meets the demand for quantitative mechanistic approaches in the growing field of immunoengineering to utilize or exploit the lymphatic system for immunotherapy.

We consider a class of density-driven flow problems. We are particularly interested in the problem of the salinization of coastal aquifers. We consider the Henry saltwater intrusion problem with uncertain porosity, permeability, and recharge parameters as a test case. The reason for the presence of uncertainties is the lack of knowledge, inaccurate measurements, and inability to measure parameters at each spatial or time location. This problem is nonlinear and time-dependent. The solution is the salt mass fraction, which is uncertain and changes in time. Uncertainties in porosity, permeability, recharge, and mass fraction are modeled using random fields. This work investigates the applicability of the well-known multilevel Monte Carlo (MLMC) method for such problems. The MLMC method can reduce the total computational and storage costs. Moreover, the MLMC method runs multiple scenarios on different spatial and time meshes and then estimates the mean value of the mass fraction. The parallelization is performed in both the physical space and stochastic space. To solve every deterministic scenario, we run the parallel multigrid solver ug4 in a black-box fashion. We use the solution obtained from the quasi-Monte Carlo method as a reference solution.

Cardiac vascular diseases, especially acute myocardial infarction (AMI), are one of the leading causes of death worldwide. Therefore cardio-specific biomarkers such as cardiac Troponin I (cTnI) play an essential role in diagnostics. In order to enable rapid and accurate measurement of cTnI with the potential of online measurements, a proof of concept of a chemiluminescence-based biosensor is presented. A flow cell was designed and combined with a sensitive CMOS camera allowing an optical readout. In addition, a microfluidic setup was established, and cTnI was determined selectively. The biomarker cTnI was expressed in E. coli, and its characterization and correct folding were investigated by different analytical methods. This recombinant cTnI was used for enzyme-linked immunosorbent assays (ELISA), calibrated against commercially available recombinant cTnI, and applied for the biosensor measurements. Based on chemiluminescence detection, the biosensor was successfully tested, and the cTnI biomarker could be reproducibly determined in buffer, spiked blood serum, and plasma.

This study numerically evaluated the long-term and stable trends of meandering channel planform at different mean annual subcritical flows based on a depth-averaged linearized meander evolution model. The calculation cases included an idealized sine-generated meander with moderate max-deflection angle and a typical natural meander - Jiyun River (in China). Within the increase of the selection of the mean annual width-depth ratio in a certain scope, the results showed some specific phase characteristics of channel centerline evolution: (1) the meander straightening trend became weaker in phase 1 (B/H ≤ 16.5) and gradually turned into the meander developing trend in phase 2 (B/H ≤ 27) with the overall immunity to flow magnitude; (2) the symmetric development form along the transverse direction perpendicular to the flow average direction was broken starting from the downstream tail in phase 3 (B/H ≤ 28.9), meantime accompanied by the highlight of flow effects when the mean annual B/H exceeded 28; (3) in phase 4 (B/H ≤ 29.5), there occurred obvious incipience and jump process of the channel sensitivity responding to flow when the selected B/H crossed 29.3, which were very similar to the transition process from the laminar flow to turbulent flow. Besides, the initial sinuosity and curvature-ratio indicator could contribute much to the channel evolutionary state, as demonstrated in the comparison between natural Jiyun River case and the correspondingly idealized sine-generated meander case with the same level of mean annual B/H. This research provides innovation spaces for deeper meander mechanism exploration and effective riparian management.

Keywords: flow mediated skin fluorescence; FMSF technique; NADH fluorescence, microcirculation, flowmotion, reactive hyperemia response, RHR, hypoxia sensitivity, HS, normoxia oscillatory index, NOI

Self-organized criticality (SOC) is a celebrated paradigm from the 90’s for understanding dynamical systems naturally driven to its critical point, where the power-law dynamics taking place make predictions practically impossible, such as in stock prices, earthquakes, pandemics and many other problems in science related to phase transitions. Shortly thereafter, it was realized that traffic flow might be in the SOC category, implying that conventional traffic management strategies seeking to maximize the local flows can become detrimental. This paper shows that the Kinematic Wave model with triangular fundamental diagram, and many other related traffic models, indeed exhibit SOC, thanks in part to the fractal nature of traffic exposed here on the one hand, and our need to get to our destinations as soon as possible, on the other hand. Important implications for congestion management of traffic near the critical region are discussed, such as: (i) Jam sizes obey a power-law distribution with exponent 1/2, implying that both its mean and variance become ill-defined and therefore impossible to estimate. (ii) Traffic in the critical region is chaotic in the sense that predictions becomes extremely sensitive to initial conditions. (iii) However, aggregate measures of performance such as delays and average speeds are not heavy tailed, and can be characterized exactly by different scalings of the Airy distribution, (iv) Traffic state time-space “heat maps” are self-affine fractals where the basic unit is a triangle, in the shape of the fundamental diagram, containing 3 traffic states: voids, capacity and jams. This fractal nature of traffic flow calls for analysis methods currently not used in our field.

Hospital bed shortage is a worldwide concern. Beds unavailability has caused elective surgery cancellations, at our hospital peaking in spring 2016 at over 50%. This is often due to difficult patient step-down from intensive care (ICU) and high-dependency units (HDU). In our general/digestive surgery service admitting approximately 1000 patients yearly, ward rounds were run on a consultant firm basis. We report a quality improvement (ISRCTN13976096) introducing in our service a structured daily multi-disciplinary board round framework (SAFER Surgery R2G) adapted from the “SAFER patient flow bundle” and the "Red to Green days” approaches to enhance flow, comparing the previous year to 2017, when our framework was applied for 12 months.We used a Plan-Do-Study-Act (PDSA) methodology. Our intervention consisted in 1) systematic communication of the key care plan after the afternoon ward rounds to the nurse in charge; 2) 30’ 10AM Monday-to-Friday multidisciplinary board rounds, attended daily by the senior-team and weekly by hospital and site managers, revising the key care plan aiming at safe, early discharges, assessing the appropriateness of each inpatient day and tackling any cause of delay. We measured patient flow by average length of stay (LOS), ICU/HDU step-downs and operation cancellations count, monitoring safety through early 30-day readmissions. Compliance was assessed by board round attendance and staff satisfaction rate surveys.After 12 months (PDSA 2, N=1032), LOS significantly decreased from 7.2(±8.9) to 6.3(±7.4) days (p=0.003); ICU/HDU bed step-down flow increased by 9.3% from 345 to 375 (p=0.197), surgery cancellations dropped from 38 to 15 (p=0.100). 30-day re-admissions increased from 0.9% (N=9) to 1.3% (N=14)(p=0.390). Average cross-specialty attendance was 80%. Satisfaction rates were >75%, regarding enhanced teamwork and faster decisions.The SAFER Surgery R2G framework has shown an increase in patient flow in the context of an enhanced multidisciplinary approach, requiring senior staff commitment to remain sustainable.

Pancreatic cancer exhibits a poor prognosis due to the lack of early diagnostic biomarkers and the resistance to conventional chemotherapy. CD44 has been known as a cancer stem cell marker, and plays tumor promotion and drug resistance in various cancers. Especially, the splicing variants are overexpressed in many carcinomas, and play essential roles in the cancer stemness, invasiveness or metastasis, and resistance to treatments. Therefore, the understanding of each CD44 variant (CD44v) function and distribution in carcinomas is essential for the establishment of CD44-targeting tumor therapy. In this study, we immunized mice with CD44v3–10-overexpressed Chinese hamster ovary-K1 (CHO) cells, and established various anti-CD44 monoclonal antibodies (mAbs). One of the established clones (C44Mab-3; IgG1, kappa) recognized peptides of the variant 5-encoded region, indicating that C44Mab-3 is a specific mAb for CD44v5. Moreover, C44Mab-3 reacted with CHO/CD44v3–10 cells or pancreatic cancer cell lines (PK-1 and PK-8) by flow cytometry. The apparent KD of C44Mab-3 for CHO/CD44v3–10 and PK-1 was 7.1 × 10−10 M and 1.9 × 10−9 M, respectively. C44Mab-3 could detect the exogenous CD44v3–10 and endogenous CD44v5 in western blotting, and stained the formalin-fixed paraffin-embedded pancreatic cancer cells, but not normal pancreatic epithelial cells in immunohistochemistry. These results indicate that C44Mab-3 is useful for detecting CD44v5 in various applications, and expected for the application of pancreatic cancer diagnosis and therapy.

The mitochondrial marker, cytochrome oxidase subunits II gene (mtDNA-COII) was employed to assess the genetic structure and diversity of Anopheles funestus, a very important malaria vector in Africa, that adapt and colonize different ecological niches in western Kenya. Mosquitoes were collected using mechanical aspirators in four sites (Bungoma, Port Victoria, Kombewa and Migori) in western Kenya. Following morphological identification, PCR was used to confirm species. The mtDNA-COII gene was amplified, sequenced and analyzed to determine genetic diversity and population structure. A total of 126 (Port Victoria-38, Migori-38, Bungoma-22 and Kombewa-28) sequences of mtDNA-COII were used for population genetic analysis. Anopheles funestus had high haplotype diversity (Hd= 0.97 to 0.98) but low nucleotide diversity (π =0.004 to 0.005). The neutrality test revealed significant (p<0.05) negative Tajima’s D and Fs values indicating population expansion with an excess of low-frequency variation due to evolutionary forces across all sites. No genetic differentiation or structure was observed across the sites (Fst = -0.01) and a high level of gene flow (Gamma St, Nm = 17.99 to 35.22) was observed among the populations. Population expansion suggests the high adaptability of this species to various ecological requirements hence sustaining its vectorial capacity and malaria transmission.

Introduction: Hemostatic dysfunction during extracorporeal membrane oxygenation (ECMO) due to blood-circuit interaction and the consequences of shear stress by flow rates lead to rapid activation of the coagulation cascade and thrombus formation in the ECMO system and blood vessels. In this study, we aimed to identify the incidence and risk factors for cannula-associated arterial thrombosis (CaAT) post-decannulation. Methods: A retrospective study of patients undergoing arterial cannula removal following ECMO. We evaluated the incidence of CaAT and compared clinical characteristics, pre-ECMO severity, and daily hemostasis parameters in patients with and without CaAT. Multivariate analysis revealed the risk factors for CaAT. Results: Forty-seven patients requiring venoarterial ECMO or hybrid methods were recruited to be screened for thrombosis. The median SOFA score was 11 (8-13). CaAT occurred in 29 patients (61.7%), with thrombosis in the superficial femoral artery accounting for 51.7%. Limb ischemia complications in the group with CaAT was 17.2%. In multivariate analysis, an ECMO flow rate of 100 mL/min was determined to be the independent factor for CaAT with an OR of 0.84 (95% CI, 0.73–0.95, p=0.008). Conclusion: In patients successfully weaned from ECMO, the incidence of CaAT was 61.7%. Our study found that a low-flow rate of ECMO was an independent risk factor for CaAT.

The analogy between the theory of phase transitions in simple fluids and vehicular traffic flow has long been suspected, promising a new level of understanding of urban congestion by standing on one of the firmer foundations in physics. The obstacle has been the interpretation of the thermal energy of the gas-particle system, which remains unknown. This paper proposes the flow of cars through the network as a viable interpretation, where the fundamental diagram for traffic flow would be analogous to the coexistence curve in gas-liquid phase transitions. Thanks to the power-law form of the coexistence curve, it was possible to formalize that the resulting network traffic model belongs to the Kardar-Parisi-Zhang universality class. The scaling relationships arising in this universality class are found to be consistent with West's scaling theory for cities. It is shown that congestion costs (delays + fuel consumption) scale superlinearly with city population, possibly and worryingly more so than predicted by West's theory. Implications for sustainability and resiliency are discussed.

In recent years, functional fluidic electrohydrodynamic (EHD) pumps have attracted considerable attention due to their remarkable features, such as simple structure, quiet operation, and energy-efficient utilization. EHD liquid pumps can be used in various industrial applications, like flow transfer, thermal management, and actuator drive. In this paper, the author reviewed EHD liquid pump research in these specific aspects: the first observation of the EHD effect, its mathematical modeling, and the choice of pump structure, electrode configuration, and working medium. Based on the review, a summary of the development and latest research on EHD pumps can be provided for the readers.

A novel physiologically based algorithm (PBA) for fast CFD computation of Flow Fractional Reserve (FFR) in Coronary Artery Trees (CATs) is proposed and developed, which, unlike traditional methods, is based on the extension of the Murray’s law for blood vessels at the outlets and extra inlet conditions prescribed alternatively and iteratively. The PBA is then implemented in both SimVascular and Ansys CFD for testing and validation. For validation purpose, 3D models of CATs are built by using their CT images and computational meshes generated for mesh convergence study. Results obtained are then compared with Invasive Coronary Angiographic (ICA) data for validation and evaluation of its accuracy and computational efficiency. It is found that discrepancies between experimental and calculated values of pressure and flow rate at the inlet were less than 0.1% at the end of the 10^th round of iteration or less. Further validation shows that the difference between estimated and experimental FFR agree with each other with a maximum difference of 1.62% after convergence is achieved. The PBA is found to be a robust patient-specific and physiologically sound method that can be a good alternative to the existing Lumped Parameter Model (LPM) which is based on empirical scaling correlations using limited population-averaged data and requires nonlinear iterative computation for convergence.

A novel physiologically based algorithm (PBA) for the computation of fractional flow reserve (FFR) in coronary artery trees (CATs) using computational fluid dynamics (CFD) is proposed and developed. The PBA is based on the extension of Murray's law and additional inlet conditions prescribed iteratively, and is implemented in OpenFOAM for testing and validation. 3D models of CATs are created using CT scans and computational meshes, and the results are compared to in-vasive coronary angiographic (ICA) data to validate the accuracy and effectiveness of the PBA. The discrepancy between calculated and experimental FFR is within 2.33-5.26% in steady-state and transient simulations, respectively, when convergence is reached. The PBA is a reliable and physiologically sound technique compared to the current lumped parameter model (LPM), which is based on empirical scaling correlations and requires nonlinear iterative computing for conver-gence. The accuracy of the PBA method is further confirmed using the FDA nozzle, which demonstrates good alignment with CFD-validated values.

Leishmaniasis is a vector-borne parasitic infection caused by the bite of female Phlebotomine sandflies. World Health Organization (WHO) estimates 100,000 cases to be reported annually on a global scale, moreover, 13 million people were infected between 2010 and 2015 worldwide. Treatment of leishmaniasis by conventional synthetic compounds is met by challenges pertaining to adverse effects which call for the discovery of newer anti-leishmanial molecules. This study was performed to evaluate the effect and modes of action of a sesquiterpene alcoholic molecule Farnesol on Leishmania major, the causative agent of Zoonotic Cutaneous leishmaniasis. The cytotoxic effect of Farnesol against L. major promastigotes, amastigotes and macrophages was assessed by MTT test and counting. The IC50 on promastigotes by Farnesol on L. major was evaluated by flow cytometry. In the findings, Promastigotes were reduced at 167 µM/mL & the mean numbers of L. major amastigotes in macrophages were significantly decreased in exposure to Farnesol at 172 µM/ml. In addition, Farnesol demonstrated no cytotoxicity on macrophages as the IC50 value was 945 µM/ml; it induced significant apoptosis dose-dependent on L. major promastigotes. In silico protein-ligand binding analyses indicated the effect of Farnesol in perturbation of the ergosterol synthesis pathway of Leishmania with attributes suggesting inhibition of Lanosterol-α-demethylase, the terminal enzyme of ergosterol synthesis machinery. Findings from flow cytometry reveal the role of farnesol in apoptosis-induced killing in promastigotes. Farnesol was effective at very lower concentrations when compared to Paromomycin. Further studies are crucial to evaluate the therapeutic potentials of Farnesol alone and in combination with other conventional drugs using clinical settings.

CD44 has been known as a marker of tumor initiating cells, and plays pro-tumorigenic functions in many cancers. The splicing variants play critical roles in malignant progression of cancers by promoting the stemness, cancer cell invasion or metastasis, and resistance to chemo- and radiotherapy. To understand each CD44 variant (CD44v) function is essential to know the property of cancers and establishment of the therapy. However, the function of the variant 4-encoded region has not to be elucidated. Therefore, specific monoclonal antibodies (mAbs) against the variant 4 are indispensable for basic research, tumor diagnosis, and therapy. In this study, we established anti-CD44 variant 4 (CD44v4) monoclonal antibodies (mAbs) by immunizing mice with a peptide containing the variant 4-encoded region. We next performed flow cytometry, western blotting, and immunohistochemistry to characterized them. One of the established clones (C₄₄Mab-108; IgG₁, kappa) reacted with CD44v3-10-overexpressed Chinese hamster ovary-K1 cells (CHO/CD44v3-10). The K_D of C₄₄Mab-108 for CHO/CD44 v3-10 was 3.4 × 10⁻⁷ M. In western blot analysis, C₄₄Mab-108 detected CD44v3-10 in the lysate of CHO/CD44v3-10 cells. Furthermore, C₄₄Mab-108 stained formalin-fixed paraffin-embedded oral squamous carcinoma tissues in immunohistochemistry. These results indicated that C₄₄Mab-108 is useful to detect CD44v4 in various applications.

The turbulent Poiseuille flow between two parallel plates is one of the simplest possible physical situations, and it has been studied intensively. In this paper, we propose a modified Prandtl-van Driest mixing length that satisfies both boundary conditions and wall damping effects. With our new formulations, we numerically solve the problem and, moreover, propose an approximate analytical solution of mean velocity. As applications of our solution, an approximate analytical friction coefficient of turbulent Poiseuille flow is proposed.

Since its introduction almost 50 years ago, the concept of ‘flow’ has been descriptive of optimal experiences, also in relation to play. However, the explorative nature of play leads to some discrepancies between flow and the optimal experience of play. In this paper the differences between flow and play are explored, leading to proposing the state of ‘wonder’ (directed at exploration) as an alternative to ‘flow’. From this perspective, the study further explores how we may design toys that enable meaningful experiences of play, identifying opportunities in designing for toys as the enablers of immersed experiences of wonder.

This study employs a high-fidelity numerical framework to determine the plastic material flow patterns and temperature distributions that lead to void formation during friction stir welding (FSW), and to relate the void morphologies to the underlying alloy material properties and process conditions. Three aluminum alloys, viz., 6061-T6, 7075-T6, and 5053-H18 were investigated under varying traverse speeds. The choice of aluminum alloys enables investigation of a wide range of thermal and mechanical properties. The numerical simulations were validated using experimental observations of void morphologies in these three alloys. Temperatures, plastic strain rates, and material flow patterns are considered. The key results from this study are: (1) The predicted stir zone and void morphology are in good agreement with the experimental observations, (2) The temperature and plastic strain-rate maps in the steady-state process conditions show a strong dependency on the alloy type and traverse speeds, (3) The material velocity contours provide a good insight into the material flow in the stir zone for the FSW process conditions that result in voids as well as those that do not result in voids. The numerical model and the ensuing parametric studies presented in this work provide a framework for understanding material flow under different process conditions in aluminum alloys, and potentially in other alloys. Furthermore, the utility of the numerical model for making quantitative predictions and investigating different process parameters to reduce void formation is demonstrated.

In electric circuits, energy is delivered by electromagnetic fields through the space, as suggested by Kraus and Carver. They provide insights by showing electric/magnetic fields and Poynting vector directions around a DC circuit. In this work, the energy flow mechanism by Kraus and Carver is further studied theoretically for arbitrary terminal potentials of a DC power source.

Uncultured, unmodified, autologous, adipose-derived regenerative cells (UA-ADRCs) are a safe and effective treatment option for various musculoskeletal pathologies. However, it is unknown whether the composition of the final cell suspension systematically varies with the subject's individual age, sex, body mass index and ethnicity. UA-ADRCs were isolated from lipoaspirate from n=232 subjects undergoing elective lipoplasty using the Transpose RT system (InGeneron, Inc.; Houston, TX, USA). The UA-ADRCs were assessed for the number of nucleated cells, cell viability and the number of viable nucleated cells per gram of adipose tissue harvested. Cells from n=37 subjects were further characterized using four-channel flow cytometry. The present study shows, for the first time, that key characteristics of UA-ADRCs can be independent of the subject's age, sex, BMI and ethnicity. This result has important implications for the general applicability of UA-ADRCs in regeneration of musculoskeletal tissue. Future studies must determine whether in-dependence of key characteristics of UA-ADRCs of the subject's individual age, sex, BMI and eth-nicity only applies to the system used in the present study, or also to others of the more than 25 different experimental methods and commercially available systems used to isolate UA-ADRCs from lipoaspirate that have been described in the literature.

Background: The duration of the vaccine's protective efficacy against SARS-CoV-2 is unknown. Evaluation of the clinical performance of available tests is required. Objectives: To evaluate the clinical performance of three immunoassays for the detection of IgG antibodies generated by mRNA vaccines against SARS-CoV-2. Methods: Two automated immunoassays (Euroimmun Anti-SARS-CoV-2 ELISA IgG and Abbott SARS-CoV-2 CLIA IgG) and one lateral flow immunoassay (LFIA Test Livzon IgG) were tested. 300 samples distributed in 3 groups were analyzed: 100 subjects over 18 years old and under 45 years old, 100 subjects between 45-65 years old and another 100 over 65 years old. collected before vaccination, at 21 days, 1, 2, 3 and 6 months post-vaccination. Sensitivity, specificity, positive predictive value, negative predictive value, positive likelihood ratio, negative likelihood ratio, and agreement (I. Kappa) were calculated for each serological test. Results: Maximum sensitivity for IgG was 98.7%, 98.1%, and 97.8% for the ELISA Euroimmun, CLIA Abbott, and Livzon LFIA assays and maximum specificity for IgG was 99.4%, 99.9%. % and 98.4% ELISA, CLIA and LFIA respectively at 3 months after vaccination with a decrease in antibody levels from the sixth month. The best agreement was observed between ELISA and CLIA 100%; (k = 1.00). The agreement between ELIA, CLIA and LIFIA was 99% (k = 0964) at the second and third month after vaccination. Seroconversion was faster and longer lasting in the younger age groups. Conclusion: Our study showed an equivalent and homogeneous clinical performance for IgG of three immunoassays after vaccination and that the LIFIA assay is the most cost-effective, reliable and accurate for routine use in population studies of seroconversion and seroprevalence.

The CC chemokine receptor 3 (CCR3) is a receptor for CC chemokines, including CCL5/RANTES, CCL7/MCP-3, and CCL11/eotaxin. CCR3 is expressed on the surface of eosinophils, basophils, a subset of Th2 lymphocytes, mast cells, and airway epithelial cells. CCR3 and its ligands are involved in airway hyperresponsiveness in allergic asthma, ocular allergy, and cancers. Therefore, CCR3 is an attractive target for those therapies. Previously, anti-mouse CCR3 (mCCR3) monoclonal antibodies (mAbs), C3Mab-3 (rat IgG2a, kappa), and C3Mab-4 (rat IgG2a, kappa) were developed using the Cell-Based Immunization and Screening (CBIS) method. In this study, the binding epitope of these mAbs was investigated using flow cytometry. The CCR3 extracellular domain-substituted mutant analysis showed that C3Mab-3, C3Mab-4, and a commercially available mAb (J073E5) recognized the N-terminal region (amino acids 1–38) of mCCR3. Next, the alanine scanning was conducted in the N-terminal region. The results revealed that Ala2, Phe3, Asn4, and Thr5 of mCCR3 are involved in C3Mab-3 binding, whereas Ala2, Phe3, and Thr5 are essential to C3Mab-4 binding, and Ala2 and Phe3 are crucial to J073E5 binding. These results reveal the involvement of the N-terminus of mCCR3 in the recognition of C3Mab-3, C3Mab-4, and J073E5.

The coastal Peru, one of the driest deserts in the world, has recently experienced dramatic landscape changes and asset destruction during precipitation events due to El Niño. Nevertheless, catastrophic explanations for landscape variations and human responses to the so-called "Super" or "Mega" El Niños are recurrent in pre-Hispanic time, even if alternative hypotheses were provided in literature. A deeper understanding of the geological and archaeological record can improve the knowledge on the relationship between such a coupled atmosphere-ocean phenomenon and landscape processes. The bibliographic sources required for this purpose are scattered throughout various disciplines ranging from physical to human sciences, thus comprehensive databases were used to identify and screen the relevant studies. The results provide knowledge synthesis in order to identify critical gaps and suggest specific research goals. Inferred episodes of landscape change due to severe precipitations in late pre-Hispanic time are discussed and consistencies and inconsistencies exposed. Examples of variation in landscape response due to extensive human intervention are reported.

This study presents the algorithm ACTION, defined as Automatic Center detection of Tropical cyclone (TC) using Image processing based on the Operational radar Network. Based on the high visibility of weather radar imagery, the TC’s motion vector is calculated from the continuous image change using optical flow, producing its rotation center as the TC’s center. The algorithm’s performance was verified for typhoons (TCs in the Northwestern Pacific) affecting the Korean Peninsula from 2018–2021 and showed a high detection rate of 80.8% within an error distance of 40 km compared to the best track of the Korea Meteorological Administration (KMA). The detection rate was 100% for typhoons with temporally consistent morphological characteristics. ACTION automatically generates TC center information upon the TC’s initial entry inside the observation radius even in the absence of uniform radar data. ACTION easily calculates using Open Source Computer Vision, performs in real time, and can be directly applied to rapidly generated weather radar images; hence, it is currently being utilized by the KMA. The high-temporal-resolution TC center information calculated through ACTION is expected to improve the efficiency of TC forecasting.

Mass transfer is often the rate determining step for solid-liquid chemical reactions. Decrease of the concentration boundary layer thickness is essential to intensify the chemical reaction. Because the concentration boundary layer exists in the velocity boundary layer, force imposition in the concentration boundary layer by superimposing an electrical current and a magnetic field was proposed. Through, flow can be directly excited in the concentration boundary layer. The previous result indicates that by superimposing a DC current and a gradient magnetic field, the development of the concentration boundary layer was suppressed, because of a macro-scale flow excitation in the whole vessel. And by superimposing the gradient magnetic field with a modulate current, the development of the concentration boundary layer was further suppressed. This is because of the macro-scale flow enhancement and the excitation of a micro-scale flow near the solid-liquid interface. However, the mechanism for the micro-scale flow excitation has not been clarified. To clarify this, a uniform magnetic field was superimposed with the DC current or the modulate current. By this means, only the micro-scale flow was excited near the anode surface. The results found that the non-unform electromagnetic force distribution is the main reason for the micro-scale flow excitation.

The problem of fluid dynamics can be greatly simplified if, for every point in space, the strain-rate tensor is diagonalized. This tensor is introduced into the Navier-Stokes equations via material law and divergence of the stress tensor. This article shows that local SO(3)xU(1) gauge fields can be used to locally diagonalize the diffusion components of the strain-rate tensor. The gauge fields resulting from the connection can be interpreted as convection components of the flow, they show properties of quasiparticles and can be interpreted as elementary vortices. Thus, the proposed approach not only offers new insights for the solution and situative simplification of the Navier-Stokes equations, it also uncovers hidden symmetries within the flow convection, allowing - depending on boundary conditions - further interpretation.

When existing at emulsion interface and continuous phase, dispersibility of water-soluble flexible polymer chains has obvious effect on rheology and dielectric properties of whole emulsion. CNF Pickering emulsion is a good system to research these properties with respect to their microscopic phase structure, dielectric and rheological properties by using cellulose nanofibers (CNF) as water-soluble Pickering emulsifier, liquid Paraffin as oil phase and DDAB as a cationic auxiliary surfactant. The CNF- and DDAB-contents were systematically varied while the water to paraffin oil ratio remained constant to discern the influence of the Pickering emulsifiers. Polarized optical microscopic images revealed that the droplets have tendency to become smaller size for higher CNF content, but bigger size for higher DDAB content, which was proved by the fluorescent analysis for CNF dispersibility with varying DDAB content. The dielectric damping exhibits a minimum, whose value decreases with increasing DDAB- and CNF-content. Increasing the DDAB-content promotes solubilization of CNFs in the aqueous phase and will increase the overall viscosity and yield points. Similarly, a higher CNF-content leads to a higher viscosity and yield point, but at high DDAB-contents the viscosity function exhibits an S-shape at intermediate CNF-content. To evaluate the results further they were compared with CNF-dispersions (without oil-phase), which showed a surfactant effect slightly on maximum stress but strongly on yield stress τy, indicating DDAB can promote the formation of CNF network rather than the viscosity of whole system.

Abstract Aim of the study: Presentation of ophthalmic symptoms of Cerebral Autosomal Dominant Arteriopathy with Subcortical Infracts and Leucoencephalopathy (CADASIL). Material and methods: Clinical presentation of female patient with diagnosed CADASIL, manifested by transient loss of vision, migraine, convergence insufficiency, diplopia, increased deep tendon reflexes of upper left limb, subcortical infarcts, mood disturbances and dementia. Results: Confirmed NOTCH3 gene mutation (p.Cys212Gly), and presence of granular osmiophilic material (GOM) in cutaneous small vessel wall in immunohistochemistry laboratory test (IHC). Magnetic resonance imaging (MRI) revealed bilateral focal vasogenic lesions in white matter of cerebral hemisphere with single micro-focal infarct in the left external capsule. Furthermore, a left eye exophoria, a bilateral peripheral visual field loss of 20 degrees and a loss of nasolabial fold was confirmed during ophthalmic tests. An eye fundus examination as well as a fluorescein angiography (FA) revealed vessel constriction of retinal arteries and a peripheral retinal pigment epithelium (RPE) atrophy with focal drusen in the left eye. The doppler ultrasonography (USG) confirmed a decreased blood flow and an increased vascular resistance of the extraocular vessels. The pattern electroretinogram (PERG) revealed a reduced P50 wave amplitude in the patient’s left eye. Conclusions: intermittent blindness, migraine, convergence failure, diplopia with specific MRI signs, NOTCH3 mutation, and the presence of GOM in the skin of small blood vessels in a young or middle-aged patient suggests CADASIL. New observations include: atrophic changes in the RPE, hemodynamic disturbances in blood flow in the short posterior ciliary arteries and in the central retinal artery, single drusen in the retina, and a reduced amplitude of the P50 wave in PERG.

The passenger prediction flow is very significant to transportation sustainability. This is due to some chaos of traffic jams encountered by the road users during their movement to the offices, schools, or markets at earlier of the days and during closing periods. This problem is peculiar to the transportation system of the Federal University of Technology Minna, Nigeria. However, the prevailing technique of passenger flow estimation is non-parametric which depends on the fixed planning and is easily affected by noise. In this research, we proposed the development of a hybrid intelligent passenger frequency prediction model using the Auto-Regressive Integrated Moving Average (ARIMA) linear model, Convolutional Neural Network (CNN), and Kalman Filter Algorithm (KFA). The passengers’ frequency of arrival at the bus terminals is obtained and enumerated through the closed-circuit television (CCTV) and demonstrated using the Markovian Queueing Systems Model (MQSM). The ARIMA model was used for learning and prediction and compared the result with the combined techniques of using CNN-KFA. The autocorrelation coefficient functions (ACF) and partial autocorrelation coefficient functions (PACF) are used to examine the stationary data with different features. The performance of the models was analyzed and evaluated in describing the short-term passenger flow frequency at each terminal using the Mean Absolute Percentage Error (MAPE) and Mean Squared Error (MSE) values. The CNN-Kalman-filter model was fitted into the short-term series and the MAPE values are below 10%. The Mean Square Error (MSE) shows that the CNN-Kalman Filter model has the overall best performance with 83.33% of the time better than the ARIMA model and provides high accuracy in forecasting.

The hydrochemical composition of the Upper Jurassic groundwaters in the South German Mo-lasse Basin (SGMB) indicates a heterogeneous and varying hydrogeochemical evolution, which contradicts previous flow model concepts. For this study, the data of 88 Tertiary, Cretaceous and Upper Jurassic groundwater samples were investigated for hydrochemical elements, 2H/18O-H2O isotopes, 87Sr/86Sr ratios as well as δ11B values. In addition, the geochemical composition, 87Sr/86Sr and δ11B values were analysed from depth-oriented Upper Jurassic rock samples to delineate water-rock interactions in the aquifer systems. Slightly elevated 87Sr/86Sr ratios of the carbonates compared to the typical signatures of marine Upper Jurassic carbonates indicate a synsedimentary radiogenic influence due to the erosion of the adjacent Bohemian Massif. However, these values cannot explain the significant higher Sr-isotope fingerprint of the groundwaters in the central SGMB. Different water types occur in the Upper Jurassic aquifer, primarily distinguished by the dominant cations, calcium or sodium with subclasses of the major anions. The calcium-dominated groundwaters occur mainly at the western and northern margins of the SGMB. The sodi-um-dominated ion exchange groundwaters instead dominate in the central and eastern SGMB. With increasing strontium content, the 87Sr/86Sr ratios of the Upper Jurassic groundwater samples either indicate a strontium uptake by carbonate of the host rocks, or a prevailing radiogenic sig-nature. This implies a basic interaction with terrestrial or marine Tertiary sediments. The results illustrate a downward transformational fluid flow systematic via the thick Tertiary sediment cover into the Upper Jurassic carbonate formation in the SGMB, highlighting a new understanding on the evolution of the Upper Jurassic groundwaters and a basin-wide recharge mechanism.