Abrasive Water Jet Machining (AWJM) is a non-conventional machining process that, unlike other methods, is deemed superior because of its applicability, versatility, and no heat-affected zones in the target material. The main objective of this paper was to develop a cheap, practical model for a low-pressure water jet cutting machine and provide some empirical test data for cutting delicate materials. Proper design calculations were performed and are included for both the water jet machine and the two-axis numerical control. Finite Element Analysis results validate the structural integrity of beams and columns in AWJM. Computational Fluid Dynamic analysis of the nozzle shows good agreement with the theoretical calculations regarding the pressure and velocity of the water-abrasive mixture exiting the nozzle. Modal analysis in ANSYS was done to mitigate potential failure due to resonance induced by vibrations. Limited testing on various thicknesses of polystyrene foam ranging from 1-5 mm thickness and rubber sheet of 1 mm thickness showed that even low pressure of 25-30 bar was sufficient to produce a kerf without any burr. However, extensive testing to report optimized parameters like nozzle transverse speed, standoff distance, abrasive flow rate, etc for working at low-pressure ranges is still a consideration for future investigation.

Walking of humanoid robots is dependent on precise tracking of the center of gravity and foot trajectories. Trajectory tracking is achieved by mobilizing the robot joints to produce the correct trajectory. Errors are being occurred because of assumptions on tracking the center of gravity and the foot trajectories. In this study, a numerical algorithm has been developed that produces an exact and single kinematic solution in which the center of gravity and foot trajectories can be tracked with the desired precision. The effectiveness of the algorithm was examined with a dynamic simulation and compared with the method given in the literature The main highlight of this study, using the presented algorithm, the robot can walk even if the position of its center of gravity is lower than its hips, resulting tracking error was smaller than reported in the literature.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

The article presents the method of identification of dynamic models for different flight states of a rotary-wing UAV. Experimental flights were conducted to obtain data necessary for the identification process. Such models can later be implemented in simulations to represent the behavior of real-life objects. Simulation of UAV swarms is the first stage of developing a swarm system, where prototyping with physical models is problematic. Therefore, obtaining accurate models is crucial for the simulation process to be reliable. Also, verification of obtained models was performed to make sure that they were identified correctly. In particular, the presented method was proven effective and successfully used in some applications.

This report discusses the application of approximate dynamic programming (ADP) and Krylov subspace methods in solving sequential decision-making problems in machine learning. ADP is used when dealing with large state spaces or when the exact dynamics are unknown. The paper explores various ADP methods such as temporal difference learning and least-squares policy evaluation. The authors also focus on the use of Krylov subspace methods for solving the Bellman equation in ADP. The report provides insights into linear approximation, stochastic algorithms, and the Arnoldi algorithm for orthonormal basis. Overall, the paper highlights the theoretical foundation provided by ADP and its connection with Krylov subspace methods, shedding light on their application in computer science.

We have developed a self-consistent model for predicting velocity of 1/2[111] screw dislocation in binary iron--carbon alloys gliding by a high-temperature Peierls mechanism. The methodology of modelling includes: (i) Kinetic Monte-Carlo (kMC) simulation of carbon segregation in dislocation core and determination the total carbon occupancy of the core binding sites; (ii) Determination of kink-pair formation enthalpy of a screw dislocation in iron---carbon alloy; (iii) KMC simulation of carbon drag and determination of maximal dislocation velocity at which the atmosphere of carbon atoms can follow a moving screw dislocation; (iv) Self consistent calculation of average velocity of screw dislocation in binary iron--carbon alloys gliding by a high-temperature kink-pair mechanism under constant strain rate. We conduct a quantitative analysis of the conditions of stress and temperature at which screw dislocation glide in iron--carbon alloy is accomplished by a high-temperature kink-pair mechanism. We estimate the dislocation's velocity at which screw dislocation brakes away from the carbon cloud and thermally-activated smooth dislocation propagation is interrupted by sporadic bursts controlled by athermal dislocation activity.

Rainfall runoff modeling has been a subject of interest for decades due to a need to understand a catchment system for management, for example regarding extreme event occurrences such as flooding. Tropical catchments are particularly prone to the hazards of extreme precipitation and the internal drivers of change in the system, such as deforestation and land use change. A model framework of dynamic TOPMODEL, DECIPHeR v1 - considering the flexibility, modularity and portability - and Generalized Likelihood Uncertainty Estimation (GLUE) method are both used in this study. They reveal model performance for the streamflow simulation in a tropical catchment, i.e. the Kelantan River in Malaysia, that is prone to flooding and experiences high rates of land use change. 32 years' continuous simulation at a daily time scale simulation along with uncertainty analysis resulted in a Nash Sutcliffe Efficiency (NSE) score of 0.42 from the highest ranked parameter set, while 25.35% of the measurement falls within the uncertainty boundary based on a behavioral threshold NSE 0.3. The performance and behavior of the model in the continuous simulation suggests a limited ability of the model to represent the system, particularly along the low flow regime. In contrast, the simulation of eight peak flow events achieves moderate to good fit, with the four peak flow events simulation returning an NSE > 0.5. Nonetheless, the parameter scatterplot from both the continuous simulation and analyses of peak flow events indicate unidentifiability of all model parameters. This may be attributable to the catchment modelling scale. The results demand further investigation regarding the heterogeneity of parameters and calibration at multiple scales.

Since the outbreak of 2019 novel coronavirus (2019-nCoV) at the hardest-hit city of Wuhan, the fast-moving spread has killed over three hundred people and infected more than ten thousands in China¹. There are more than one hundred cases outside of China, affecting a dozen of countries globally². The genome sequence of 2019-nCoV has been reported and fast diagnostic kits, effective treatment as well as preventive vaccines are rapidly being developed³. Initial fast-growing confirmed cases triggered lock-down of Wuhan as well as nearby cities in Hubei Province. Mathematical models have been proposed by scientists around the world to project the numbers of infected cases in the coming days ^4,5. However, major factors such as transportation and cultural customs have not been weighed enough. Our model is not set out for precise prediction of the number of infected cases, rather, it is meant for a glance of the dynamics under a public epidemic emergency situation and of different contributing factors. We hope that our model and simulation would provide more insights and perspective information to public health authorities around the globe for better informed prevention and containment solution.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

The study of values at European and global level has gained momentum along with the theory of values launched by Schwartz. Values are dormant, hidden, unobservable and impossible to measure directly. They exist somewhere within the human being, manifested by different attitudes, depending on their degree of generality. The paradigm of basic human values implies shared universal values that are encountered in cultures all over the world. The theory of values designed by Schwartz has refined the pool of 19 basic individual values representing principles in individuals and group, further describing the dynamic relationships among them. This study presents practical evidence of the dynamics between individual values, the dynamics theorized by Schwartz in 2012. Following the development of an online questionnaire made up of 46 items with online responses options on a Lickert scale from 1 to 6, where 1 represents less important and 6 represent very important, 220 young people from Western Romania voluntarily responded. By testing the hypothesis assuming the dynamic relationship between the two values through multiple regression analysis, the results demonstrate that in Model 1, which involves a linear relationship, health explains 42% of the variance in security with a F =161,215 significant at p <.01. In Model 2, which involves a curvilinear relationship, health explains 50% of the variance in security version with a F = 35,336 significant at p <.01. The incremental prediction optimization of 8% added by including the squared security accounts for the curve in the regression line, indicating the existence of a curvilinear relationship between security and health. The dynamic relationship demonstrates that upper limit and lower limit aspects of security, significantly influence the health value in a negative way. Normal levels of security trigger a high level of prioritization of health value. The implications of this type of relationship are discussed in explaining the value phenomenon at individual level. The study shows limits due to the selected sample, focusing exclusively on young people with higher education from the Western region of Romania. This sample was the target group of "The National Identity of Romanian Youth" project which designed this research.

A Smart Home is characterized by the presence of a huge number of small, low power devices, along with more classical devices. According to the Internet of Things (IoT) paradigm, all of them are expected to be always connected to the Internet in order to provide enhanced services. In this scenario, an attacker can undermine both the network security and the user’s security/privacy. Traditional security measures are not sufficient, because they are too difficult to setup and are either too weak to effectively protect the user or too limiting for the new services effectiveness. The paper suggests to dynamically adapt the security level of the smart home network according to the user perceived risk level what we have called network sentiment analysis. The security level is not fixed, established by a central system (usually by the Internet Service Provider) but can be changed with the users cooperation. The security of the smart home network is improved by a distributed firewalling and Intrusion Detection Systems both to the smart home side as to the Internet Service Provider side. These two parts must cooperate and integrate their actions for reacting dynamically to new and ongoing threats. Moreover, the level of network sentiment detected can be propagate to nearby home networks (e.g. the smart home networks of the apartments inside a building) to increase/decrease their level of security, thus creating a true in-line Intrusion Prevention System (IPS). The paper also presents a test bed for Smart Home to detect and counteract to different attacks against the IoT devices,,Wi-Fi and Ethernet connections .

This paper studies a model of dynamic compensation and capital structure with managerial traits. We show that Optimistic manager perceives equity as more undervalued than debt, while, confident manager perceives debt as more undervalued than equity. Managerial risk aversion mitigates manager’s bias. The risk aversion of the optimistic manager has a convex effect on the optimal coupon. There exists the level of risk aversion eliminating the bias on the leverage. The managerial optimist has an ambiguous effect on the owner’s bankruptcy level. The risk aversion has a convex effect on the owner’s bankruptcy level. The optimistic/confident manager underestimates the credit spread. The risk aversion has convex effect on the credit spread. In contrast to rational manager, the optimistic/confident manger has higher level of effort. The risk aversion has a negative effect on the effort.

Piezoelectric cantilever harvesters have a large power output at their natural frequency, but in some applications the frequency of ambient vibrations is different from the harvester’s frequency and/or ambient vibrations are periodic with some harmonic components. To cope with these operating conditions harvesters with integrated trimming devices (ITDs) are proposed. Some prototypes are developed with the aid of an analytical model and tested with an impulsive method. Results show that a small trimming device can lower the main resonance frequency of a piezoelectric harvester of the same extent as a larger tip mass and moreover generates at high frequency a second resonance peak. A multi-physics numerical FE model is developed for predicting the generated power and for performing stress-strain analysis of harvesters with ITDs. The numerical model is validated on the basis of experimental results. Several configurations of ITDs are conceived and studied. Numerical results show that harvesters with ITDs are able to generate relevant power at two frequencies owing to the particular shape of the modes of vibration. The stress in the harvesters with ITDs is smaller than the stress in the harvester with a tip mass trimmed to the same frequency.

For better export marketing strategies (EMS), companies mobilize their internal resources, which are managerial commitment, firm experience, and product uniqueness. However, Small businesses with constrained resources cannot be well explained with this view. So, more research on how small business come up with EMS have been called for. To explain how resource-restricted firms which rely heavely on entrepreneur, this study adopted the concept of dynamic managerial capabilities (DMCs) and resource versatility to better explain small business exports. We analyzed small businesses in Mongolia with qualitative research methods, including interviews with entrepreneurs and support organizations, site visits, and group discussions. We suggest international dynamic marketing capabilities (IDMCs), which are entrepreneurial orientation, networking capability, and versatile dynamic capability for small business. Theoretical and managerial implications are discussed.

Hexakis(2-alkoxy-1,5-phenyleneimine) macrocycles were synthesized using a simple one−pot procedure through by precipitation−driven cyclization. The acetal−protected AB−type monomers, 2-alkoxy-5-aminobenzaldehyde diethyl acetals, underwent polycondensation in water or acid−containing tetrahydrofuran. The precipitation−driven cyclization based on imine dynamic covalent chemistry and π−stacked columnar aggregation played a decisive role in the one−pot synthesis. The progress of the reaction was analyzed by MALDI−TOF mass spectrometry. The macrocycles with alkoxy chains were soluble in specific organic solvents such as chloroform, allowing their structures to be analyzed by NMR. The shape−anisotropic, nearly planar, and persistent macrocycles aggregated into columnar assemblies in polymerization solvents, driven by aromatic π−stacking. The octyloxylated macrocycle OcO−Cm6 exhibited an enantiotropic columnar liquid crystal−like mesophase between 165°C and 197°C. In the SEM image of (S)-(−)-3,7-dimethyloctyloxylated macrocycle (−)BCO-Cm6, columnar substances with a diameter of 100−200 nm were observed. The polymerization solution for 2-(2-methoxyethoxy)ethoxy)ethoxylated macrocycle (TEGO−Cm6) gelled and showed thixotropic properties by forming a hydrogen bond network.

In recent years, demand has been increasing for target detection and tracking from aerial imagery via drones using onboard powered sensors and devices. We propose a very effective method for this application based on a deep learning framework. A state-of-art embedded hardware system empowers small flying robots to carry out the real-time onboard computation necessary for object tracking. Two types of embedded modules were developed: one is designed using a Jetson TX or AGX Xavier, and the other is based on an Intel Neural Compute Stick. These are suitable for real-time onboard computing power on small flying drones with limited space. A comparative analysis of current state-of-art deep-learning-based multi-object detection algorithms was carried out utilizing the designated GPU-based embedded computing modules to obtain detailed metric data about frame rates as well as the computation power. We also introduce an effective target tracking approach for moving objects. The algorithm for tracking moving objects is based on the extension of simple online and real-time tracking. It was developed by integrating a deep-learning-based association metric approach (Deep SORT), which uses a hypothesis tracking methodology with Kalman filtering and a deep-learning-based association metric. In addition, a guidance system that tracks the target position using a GPU-based algorithm is introduced. Finally, we demonstrate the effectiveness of the proposed algorithms by real-time experiments with a small multi-rotor drone.

The impacts of inflation on international finance are generally reflected in the decline of buying power, risks of investment and deposit loss from currency devaluation. For the purpose of optimized allocation and management of asset values, i.e., annual income or research grants, a framework of a three-level model for static financial management is presented to maximize banking interests, bonuses, and the remaining balance after spending necessary expenditures. Meanwhile, in retrospect to higher-level financial inflation, strategies of dynamic investment, i.e., posing regular tests of flipping coins, exploiting variations of the currency exchange rate, as well as applying the theory of broad money, are presented to increase the appreciation rate of net assets in and post the era of COVID-19. Quantitative evaluations in case studies verify the feasibility of improving the financial situation, indicating broader applications for budgeting and investing when US inflation rate is below 3.0%. Besides, combining approaches of static and dynamic strategies, the expected annual growth rate of individual zero-risk asset investment is predicted as within the range of 8.30~9.62% according to budgeted appreciation on net assets in 12 months, which is capable of overcoming negative impacts from higher level annual inflation, i.e., those as highest as 8.01% in the Year 2022.

Digital twins are the foundation of autonomous off-road vehicles. Dynamic reduction methods are one of several ways to develop digital twins for off-road vehicles. The article commences with a comprehensive overview of the most widely used dynamic reduction methods and then introduces performance metrics for assessing their efficacies in the context of digital twins. The paper additionally includes a detailed mathematical derivation of the state-space representation for reduced-order finite element models. The state-space representation of the reduced finite element models facilitates their export to problem-solving environments for dynamic analysis. The state-space models are eventually solved utilizing the built-in libraries of numerical solvers in textual and graphical programming platforms. In addition, the article identifies the set of solvers that best suit the simulation of virtual models for off-road vehicles. This article also includes an evaluation of the simulation results of digital models with modes ranging from 0 to 30 Hz. In addition, the article demonstrates the lower bound of the frequency range necessary and sufficient to be retained in off-road vehicle virtual models. Finally, the paper presents the simulation outcomes for digital models of commercial off-road vehicles with custom-built control, electrical, and control systems.

5G heterogeneous network overlaid by millimeter-wave (mmWave) access employs mmWave meshed backhauling as a promising cost-efficient backhaul architecture. Due to the nature of mobile traffic distribution in practice which is both time-variant and spatially non-uniform, dynamic construction of mmWave meshed backhaul is prerequisite to support the varying traffic distribution. Focusing on such scenario of outdoor dynamic crowd (ODC), this paper proposes a novel method to control mmWave meshed backhaul for efficient operation of mmWave overlay 5G HetNet through Software-Defined Network (SDN) technology. Our algorithm is featured by two functionalities, i.e., backhauling route multiplexing for overloaded mmWave small cell base stations (SC-BSs) and mmWave SC-BSs’ ON/OFF status switching for underloaded spot. In this paper, the effectiveness of the proposed meshed network is confirmed by both numerical analyses and experimental results. Simulations are conducted over a practical user distribution modeled from measured data in realistic environments. Numerical results show that the proposed algorithm can cope with the locally intensive traffic and reduce energy consumption. Furthermore, a WiGig (Wireless Gigabit Alliance certified) device based testbed is developed for Proof-of-Concept (PoC) and preliminary measurement results confirm the proposed dynamic formation of the meshed network’s efficiency.

Continual learning, a crucial facet of machine learning, involves the perpetual acquisition of valuable insights from incoming data, sans the necessity for full dataset access. Esteemed as a fundamental goal in artificial intelligence, continual learning grapples with an enduring challenge—catastrophic forgetting. A proficient model must exhibit adaptability for new data assimilation and robustness to retain existing knowledge. Class-incremental learning (CIL) aids the gradual integration of knowledge from newly introduced classes, forming a universal classifier. However, directly training the model with fresh class instances triggers a problem—forgetting distinguishing features of prior classes, causing a performance decline. Addressing such issues in machine learning, this survey aims to delineate significant challenges, outcomes, and recent advancements, including our contributions to CIL techniques, especially in image classification.

Despite the recognized influence of maximum or acceleration strength on combat techniques and countermovement jump (CMJ) performance, the relationship between body segment weights and combat techniques remains unexplored. This study aimed to examine the impact of body segment weights, including striking arm weight (SAW), kicking leg weight (KLW), and trunk weight (TW), on the dynamics of direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and CMJ performance. Sixteen male military cadets (22.3±1.8 years, 181.4±7.0 cm, 83.0±8.1 kg) performed combat techniques, with performance measured by using a force plate and body segment weights assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis was applied. Results indicated a strong correlation between KLW and FK impulse (r = 0.64, p ≤ 0.01) and CMJ impact force (r = 0.80, p ≤ 0.01). SAW showed moderate correlations with DP impulse (r = 0.53, p ≤ 0.05) and ES impulse (r = 0.54, p ≤ 0.05). Additionally, FK peak and impact forces were strongly correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01), and FK peak force moderately correlated with CMJ peak velocity (r = 0.63, p ≤ 0.05). These findings suggest targeted arm strength training could enhance striking abilities, while improvements in leg acceleration strength may directly boost kicking performance and vertical jump capabilities, which are crucial in combat scenarios.

Contactless charging is evolving fast in many domains and applications such as the electrical vehicles (EV). The principle consists of transferring energy between two systems without having any electrical connection between them. This power transfer can be realized by emitting a magnetic field for Inductive Power Transfer (IPT). In the automotive domain, the application of contactless charging to supply power to the vehicle while driving is one of the solutions envisaged to solve the limited autonomy range of EV and reduced its cost but the system must comply with existing standards (e.g., allocated frequency range and radiated electromagnetic emissions), as summarized in this paper.

This experimental research presents an easier model for fitting experimental results that can be simulate the dynamical behaviour of a single degree freedom system, SDFS, subjected in a forced vibration in a shaking table. The fractional damping using a Kelvin-Voigt fractional derivative rheological model, KVFRdm, to represent a fractional oscillator and compare with the experimental model.

In this paper the possibility of harvesting energy from the vibrations of a plate is analyzed. The harvester takes the form of a cantilever dynamic vibration absorber equipped with a piezoelectric layer and tuned by means of a tip mass to the first mode of vibration of the plate. A mathematical model of the coupled system composed of the plate and the harvester is presented. The validity of the proposed harvester is proved by means of simulations carried out with the modal expansions approach. Simulation results highlighting the effect of harvester tuning and location are presented as well. Then the validity of the harvester is confirmed by experimental tests carried out both with a concentrated impulsive load and with a distributed pressure load. Simulations and experimental tests show that the cantilever piezoelectric dynamic vibration absorber generates open circuit voltage an order of magnitude larger than the one generated by the same piezoelectric layer when directly bonded to the plate surface.

Liquid and gas are distinct in their extent of dynamic atomic correlations; in gas atoms are almost uncorrelated whereas they are strongly correlated in liquid. This distinction applies also to electronic systems. Fermi liquids are actually gas-like, whereas strongly correlated electrons are liquid-like. Doped Mott insulators share characteristics with supercooled liquids. Such distinctions have important implications on superconductivity. We discuss the evolution of dynamic atomic correlations in liquid with temperature, and a possible effect of dynamic correlations on the high-temperature superconductivity in the cuprates.

Addressing sustainable mobility in urban areas has become a priority in today’s society, given the growing population and increasing vehicular flow in these areas. Intelligent Transportation Systems have emerged as innovative and effective technological solutions to address these challenges. Research in this area has become crucial, as it contributes not only to improve mobility in urban areas, but also to positively impact the quality of life of its inhabitants. To address this, a dynamic clustering methodology for vehicular trajectory data is proposed which can provide an accurate representation of the traffic state. Data was collected for the city of San Francisco, a dynamic clustering algorithm was applied and then an indicator was applied to identify areas with traffic congestion. Several experiments were also conducted with different parameterizations of the forgetting factor of the clustering algorithm. The results showed in terms of precision that the dynamic clustering methodology achieved high match rates compared to the congestion indicator applied to static cells.

Semantic segmentation of remote sensing urban scene imagery is a pixel-wise prediction, which is applied to identify the land-cover or land-use category. However, semantic segmentation demands huge computation cost. In order to reduce the huge computation cost, a common method is to introduce transformer and CNN hybrid method to have a good trade-off between accuracy and computation cost. However, recent CNN-transformer hybrid methods often capture local-global context and cross-window interaction information simultaneously. Then they introduce the local-global context to fuse the local feature, which repeat fuse the local and global feature and result in the additional computation cost. And previous methods often ignore to filter the local and global feature. To fix the problem, we design a lightweight decoder-EDDformer, which is Efficient Global Value Transformer with Dynamic Gatefusion module. Efficient global value transformer only response for extracting global feature. Dynamic Gatefusion module filter the local and global semantic feature and fuse them to capture the local-global context in one time. Extensive experiments reveal that our method not only runs faster but also achieves higher accuracy compared with other state-of-the-art lightweight models.

Japanese encephalitis virus (JEV) causes acute viral encephalitis in humans and reproductive disorders in pigs. JEV emerged during the 1870s in Japan and since that time, JEV has been transmitted exclusively throughout Asia, according to known reporting and sequencing records. A recent JEV outbreak occurred in Australia which affected commercial piggeries across different temperate southern Australian states and caused confirmed infections in humans. A total of 47 human cases and seven deaths were reported. The recent evolving situation of JEV needs to be reported due to its continuous circulation in endemic regions and spread to non-endemics areas. Here, we reconstructed the phylogeny and population dynamics of JEV using recent JEV isolates for the future perception of disease spread. Phylogenetic analysis shows the most recent common ancestor occurred about 3120 years ago (YA) (95% Highest posterior density [HPD], 2680 to 3715). Our results of the Bayesian skyline plot (BSP) demonstrates that JEV demography lacks fluctuations for the last two decades, but it shows that JEV genetic diversity has increased during the last ten years. This indicates the potential JEV replication in the reservoir host, which is helping it to maintain its genetic diversity, and to continue its dispersal into non-endemic areas. The continuous spread in Asia and recent detection from Australia further support these findings. Therefore, an enhanced surveillance system is needed along with precautionary measures such as regular vaccination and mosquito control to avoid future JEV outbreaks.

Cable-Driven Parallel Robots (CDPRs) are a special kind of parallel manipulator which use cables to control the position and orientation of the mobile platform or end-effector. The usage of cables instead of rigid links offer some advantages over their conventional rigid counterparts. As cables can only pull, but not push, the number of cables (n) required to command the end-effector is always n+1. This configuration is known as fully-constrained and it is the most extended configuration for CDPRs. Although CDPRs have many advantages, such as their ability to cover large working areas, one of their main problems is that their working area (workspace) is limited in comparison to its frame area (planar case), or frame volume (spatial case), due to the minimum and maximum allowed tensions. Depending of these tensions values the workspace can be notoriously decreased. In order to tackle this problem, lots of works focus on solving kinematics or dynamics problems for cable sagging, i.e., they take into account sagging when modelling the robot kinematic and include these poses inside the usable robot workspace. Taking into account phenomenons like this increases the mathematical complexity of the problem, and much more complex techniques are required. On the other hand, the lack of workspace problem can be tackled by adding active or passive elements to the robot design. In this sense, this paper proposes two mechanical modifications: to add passive carriages to the robot frame and to use a single cable loop to command the end-effector position and orientation. This work presents the kinematic, static and dynamic models of the novel design and shows the gain of workspace for a planar case while taking into account different parameters of the robot.

Decision making is a complex process involving various parts of the brain which are active during different times. It is challenging to measure externally the exact instance when any given region becomes active during the decision-making process. Here we try to extract and visualize the dynamic functional brain activation information from the observed fMRI data. We propose the use of a regularized deconvolution model to simultaneously map various activation regions within the brain and track how different activation regions changes with time. Thus, providing both spatial and temporal brain activation information. The activation information can then be further analyzed as per need and requirements. The proposed technique was validated using simulated data and then applied to a simple decision-making task for identification of various brain regions involved in different stages of decision making. The visualization aspect of the algorithm allows us to actually see the flow of activation (and deactivation) in form of a motion picture. The dynamic estimate may aid in understanding the causality of activation between various brain regions in a better way.

Large water bodies such as the Laurentian Great Lakes have significant influences on local and regional climate through their unique physical features. Due to the coarse spatial resolution of general circulation models (GCMs), the Great Lakes are geometrically ignored in most GCMs. Thus, the dynamical downscaling technique serves as a necessary and feasible solution to bridge the gap. The Weather Research and Forecasting model (WRF) with an updated lake scheme is employed to downscale from a GCM, GFDL-CM3. The WRF-Lake’s performance is evaluated against observations, the GCM, as well as 23 other GCMs. Results show that the coupled air-lake model, with a fine spatial resolution and realistic lake bathymetries, reproduced a more reasonable spatiotemporal climatology than GCMs, as well as the lake-induced characteristics that were missed in GCMs. With lakes present, the seasonal variability of air temperature was reduced in WRF-Lake relative to GFDL-CM3, especially in summer. A reduced air temperature trend, about 4.5 °C/100 year in the 21st century, was projected in WRF-Lake. The seasonal evolutions of lake surface temperature and lake ice coverage were well captured by the lake model. The lake surface temperature was projected to be warming by 3.5-4 °C and the lake ice diminishing by 58.9% - 86%. Those results brought by the WRF-Lake model suggest that a fine resolution of the topography and the incorporation of the lake-atmosphere interactions are crucial to improve the understanding of the climate and climate change in the Great Lakes region.

The sustainability of ecotourism is the backbone of tourism development of a country. Ecotourism can contribute to both conservation and development in which involves dynamic relationship between tourism, biodiversity and communities, facilitate by great management. The purpose of this study is to analyze the dimensions of the socio-economic and environmental impacts of ecotourism in communities surrounding the Tasik Kenyir in Terengganu, Malaysia. This study provides a framework for the development and evaluation of ecotourism. The framework will determine if the relationships between indicators are positively correlated which will result in positive contribution to the other by using System Dynamic. Socio-cultural and economic data will be collected through interviews and group discussions in selected communities in Tasik Kenyir. Data on wildlife will be extracted from secondary data from Kenyir Research Institute, Universiti Malaysia Terengganu. The data analysis will explore the socio-cultural and economic differences between and within different communities due to ecotourism development, the contribution of ecotourism to conservation activities, local support for conservation and ecotourism as well as the influence of tourist activities on the distribution of wildlife species in Tasik Kenyir. This study aims to contribute toward understanding the natural resource community-ecotourism inter-relationship and help to bridge the knowledge gap that hinders biodiversity conservation initiatives. The findings will be used as a base for further development of ecotourism and will recommend alternative management options where necessary for the study area.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

Mycobacterium tuberculosis (Mtb) is the etiological agent of tuberculosis (TB), a disease that alt-hough preventable and curable, remains a global epidemic due to the emergence of resistance and a latent form responsible for a long period of treatment. Drug discovery in TB is a challenging task due to the heterogeneity of the disease, the emergence of resistance and an uncomplete knowledge of the pathophysiology of the disease. The limited permeability of the cell wall and the presence of multiple efflux pumps remain a major barrier to achieve effective intracellular drug accumulation. While the complete genome sequence of Mtb has been determined and several potential protein targets have been validated, the lack of adequate models for in vitro and in vivo studies is a limit-ing factor in TB drug discovery programs. In current therapeutic regimens, less than 0.5% of bac-terial proteins are targeted being the biosynthesis of the cell wall and the energetic metabolism two of the most important processes exploited for TB chemotherapeutics. This review provides an overview on the current challenges in TB drug discovery and emerging Mtb druggable proteins, and how chemical probes for protein profiling enabled the identification of new targets and bi-omarkers, paving the way to disruptive therapeutic regimens and diagnostic tools.

Lake Rawapening, Semarang Regency, Indonesia, has incorporated a holistic plan in its management practices. However, despite successful target achievements, some limitations remain that a review of its management plan is needed. This paper identifies and analyzes existing lake management strategies as a standard specifically in Lake Rawapening by exploring various literature, both legal frameworks and scholarly articles indexed in Google Scholar and published in Water by MDPI about lake management in many countries. There are two major types of lake management, namely pillar-based and object-based. While the former is the foundation of a conceptual paradigm that does not comprehensively consider the roles of finance and technology in the lake management, the latter indicates the objects to manage so as to create standards or benchmarks for the implementation of various programs. Overall, Lake Rawapening management should include more programs on erosion-sedimentation control and monitoring of operational performance using information systems.

Nature-based solutions (NbS) are increasingly recognised for their potential to address both the climate and biodiversity crises. These outcomes are interdependent, and both rely on the capacity of NbS to support and enhance the health of an ecosystem: its biodiversity, the condition of its abiotic and biotic elements, and its capacity to function normally despite environmental change. However, while understanding of ecosystem health outcomes of nature-based interventions for climate change mitigation is growing, the outcomes of those implemented for adaptation remain poorly understood with evidence scattered across multiple disciplines. To address this, we conducted a systematic review of the outcomes of 109 nature-based interventions for climate change adaptation using 33 indicators of ecosystem health across eight broad categories (e.g. diversity, biomass, ecosystem functioning and population dynamics). We showed that 88% of interventions with positive outcomes for climate change adaptation also reported measurable benefits for ecosystem health. We also showed that interventions were associated with a 67% average increase in local species richness. All eight studies that reported benefits in terms of both climate change mitigation and adaptation also supported ecosystem health, leading to a triple win. However, there were also trade-offs, mainly for forest management and creation of novel ecosystems such as monoculture plantations of non-native species. Our review highlights two major limitations of research to date. First, only a limited selection of metrics are used to assess ecosystem health and these rarely include key aspects such as functional diversity and habitat connectivity. Second, taxonomic coverage is poor: 67% of outcomes assessed only plants and 57% did not distinguish between native and non-native species. Future research addressing these issues will allow the design and adaptive management of NbS to support healthy and resilient ecosystems, and thereby enhance their effectiveness for meeting both climate and biodiversity targets.

Due to their increased surface area, extent of swelling and active substance loading capacity and flexibility, nanogels made from natural and synthetic polymers have gained significant interest in the scientific and industrial areas. Especially, customized design and implementation of non-toxic, biocompatible, and biodegradable micro/nano carriers makes their usage very feasible for a range of biomedical applications, including drug delivery, tissue engineering, and bioimaging. The design and application methodologies of nanogels have been outlined in this review. Additionally, the most recent advancements in nanogel biomedical applications have been discussed, with a particular emphasis on applications for the delivery of drugs and biomolecules.

Vision-based tactile sensors (VBTS) have become the de facto method of giving robots the ability to obtain tactile feedback from their environment. Unlike other solutions to tactile sensing, VBTS offers high spatial resolution feedback without compromising on instrumentation costs or incurring additional maintenance expenses. However, conventional cameras used in VBTS have a fixed update rate and output redundant data, leading to computational overhead downstream. In this work, we present a neuromorphic vision-based tactile sensor (N-VBTS) that employs observations from an event-based camera for contact angle prediction. Particularly, we design and develop a novel graph neural network, dubbed TactiGraph, that asynchronously operates on graphs constructed from raw N-VBTS streams exploiting their spatiotemporal correlations to perform predictions. Although conventional VBTS uses an internal illumination source, TactiGraph is reported to perform efficiently in both scenarios, with and without an internal illumination source. Rigorous experimental results revealed that TactiGraph achieved a mean absolute error of 0.62∘ in predicting the contact angle and was faster and more efficient than both conventional VBTS and other N-VBTS, with lower instrumentation costs. Specifically, N-VBTS requires only 5.5% of the compute-time needed by VBTS when both are tested on the same scenario.

For disciplines like biological science, security, and the medical field, link prediction is a popular research area. To demonstrate the link prediction many methods have been proposed. Some of them that have been demonstrated through this review paper are TransE, Complex, DistMult, and DensE models. Each model defines link prediction with different perceptions. We argue that the practical performance potential of these methods, having similar parameter values, using the fine-tuning technique to evaluate their reliability and reproducibility of results. We describe those methods and experiments; provide theoretical proofs and experimental examples, demonstrating how current link prediction methods work in such settings. We use the standard evaluation metrics for testing the model's ability.

Zoos are increasingly putting in place formalized animal welfare assessment programs to allow monitoring of welfare over time, as well as to aid in resource prioritization. These programs tend to rely on assessment tools that incorporate resource-based and observational animal- focused measures since it is rarely feasible to obtain measures of physiology in zoo-housed animals. A range of assessment tools are available which commonly have a basis in the Five Domains framework. A comprehensive review of the literature was conducted to bring together recent studies examining welfare assessment methods in zoo animals. A summary of these methods is provided with advantages and limitations of the approach es presented. We then highlight practical considerations with respect to implementation of these tools into practice, for example scoring schemes, weighting of criteria, and innate animal factors for consideration. It is concluded that would be value in standardizing guidelines for development of welfare assessment tools since zoo accreditation bodies rarely prescribe these. There is also a need to develop taxon or species- specific assessment tools to inform welfare management.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

To assure the opacity, an optimal problem is to retain the occurring events sequences as many as possible. Contrary to such problem, the other optimal problem is to preserve the minimal occurring events sequences. In the paper, based on the choosing cost, an optimal opacity-enforcing model is presented to minimize the sum of discount choosing cost, which is not only to preserve the opacity, but also to retain the secret to the maximum. To solve the model, two scenarios on opacity are considered. For the two scenarios, some algorithms are presented to achieve the optimal solution for the model by using the method of dynamic programming. And then, the solutions produced by the algorithms are proved correctly by theoretical proof. Finally, some illustrations for the algorithms are given.

This paper studied the dynamic characteristics of the deployment process of the replaceable interface mast and the vibration generated at the end of the mast. The interface is discretized by the absolute nodal coordinate thin shell element with gradient reduction, and the three-dimensional motion of the reconfigurable rigid body module is described by the natural coordinate method. The dynamic equations of the interface and the reconfigurable module without external constraints are established by the principle of virtual work. Finally, the dynamic models of each part are assembled into the dynamic model of the mast system deployment process through the system constraint equation. According to the established dynamic model of the mast system deployment process, the dynamic behavior changes of the replaceable interface mast are analyzed. At the same time, the differences in the deployment behavior of the replaceable interface mast under different system configuration schemes, flexible interface geometric parameters, and different driving laws are studied and compared. It provides guidance for the scheme configuration of the mast system, the structural design of the interface, and the deployment motion planning of the mast. According to the physical prototype and the assembly of the mast system model, the deployment process of the replaceable interface mast is experimentally analyzed. It shows that the established dynamic model of the mast system can correctly analyze the dynamic characteristics of the deployment behavior of the replaceable interface mast, which provides a reference for the design and behavior analysis of the mast system.

Vehicular traffic in urban areas continues to be a constant challenge today, due to the continuous population growth and the increase of vehicles in circulation. Vehicular congestion, as a recurrent problem, generates a negative impact on urban mobility and citizens’ quality of life. It is hypothesized that a dynamic clustering method of vehicle trajectory data can provide an accurate and up-to-date representation of real-time traffic behavior. To evaluate this hypothesis, data were collected from three different cities: San Francisco, Rome and Guayaquil. A dynamic clustering algorithm was applied to identify traffic congestion patterns and an indicator was applied to identify and evaluate the congestion conditions of the areas. The results show a high precision and recall in congestion classification compared to a method based on static cells.

Resource pricing in cloud computing has become one of the main challenges for cloud providers. The challenge is determining a fair and appropriate price to satisfy users and resource providers. To determine a fair price, it is necessary to consider the conditions and needs of both parties: provider and user. This research tries to provide a pricing mechanism for cloud computing based on game theory. The proposed mechanism takes into account three factors including fault possibility, interaction between virtual machines, and energy consumption to reach a fair price. In the proposed game, the provider decides on the price of the virtual machine which can be offered to the user on each physical machine and the user decides between the virtual machines offered to run its application. The whole game is implemented as a function of the resource broker component. The proposed mechanism is simulated and evaluated using the CloudSim simulator. Its performance is compared with several previous recent mechanisms. According to the results, the proposed mechanism has been able to determine a more reasonable price for the user and the provider which increases the overall profitability of the cloud system.

Ransomware constitutes a distinctive category of pernicious software that sequesters a user's digital assets by encryption, holding them hostage until a sum is extorted from the victim. These incursions have escalated to become among the most prevalent and significant threats confronting both individuals and corporate entities. In combatting this virulent program, dynamic analysis has been established as the favored detection modality. Such analyses typically hinge on Windows API calls, the conduits through which programs requisition services from the operating system. Yet, the superfluous and unrelated Windows API calls interjected by adversaries into the execution stream of suspect binaries precipitate an excessively noisy behavioral sequence, which impairs the performance of counter-ransomware mechanisms. The research outlined herein introduces a novel non-signature-based detection paradigm that harnesses efficacious Windows API call sequences through supervised machine learning strategies. An innovative Enhanced Min Max (EmRmR) filter technique is proposed, aiming to purge noisy features and isolate the most indicative feature subset that encapsulates the ransomware's true behavior. The EmRmR method, diverging from the traditional Min Max approach, circumvents the superfluous calculations that are a hallmark of the conventional algorithms, thereby necessitating a reduced number of evaluations. Additionally, a refinement procedure has been integrated to contract the program's call trace volume by discarding those Windows API calls lacking a robust correlation with ransomware's pivotal behavior. Subsequent to rigorous experimental analyses and juxtaposition with extant behavior-based detection methodologies, the proposed strategy has demonstrated its efficacy in differentiating ransomware behavior, delivering high detection precision alongside a diminution in false-positive occurrences.

Leishmaniasis is a group of neglected infectious, non-contagious diseases caused by parasites of the Leishmania genus which affects millions of people worldwide. The drugs available for its treatment, especially in cases of visceral leishmaniasis, are old, outdated, have serious side effects and in many cases are ineffective due to the emergence of resistant strains. In this context, the search for new candidates for more effective and safer drugs which can become new therapeutic alternatives is a constant need. In this work, 10 new chalcones were synthesized in high yields through Claisen-Schmidt condensation and were evaluated in vitro against Leishmania infantum promastigotes and amastigotes. CP04 and CP06 compounds were the most promising, respectively showing IC50 values = 13.64 ± 0.25 and 11.19 ± 0.22 against promastigotes, and IC50 = 18.92 ± 0.05 and 22.42 ± 0.05 against amastigotes. The compounds did not show cytotoxicity in erythrocytes, showing selectivity indexes greater than 74 and 90. Molecular docking studies carried out under the sterol 14-alpha demethylase (CYP-51) (PDB: 3L4D) and trypanothione reductase (PDB: 5EBK) enzymes from L. infantum evidenced the great affinity of the CP04 molecule for these targets, showing Moldock score values of -94.0758 and -50.5692 KJ/mol-1, with these values being much lower than the co-crystallized ligand energies. Molecular dynamics simulations demonstrated great stability of CP04 in its targets, thus indicating a real interaction possibility. Our findings confirm the potential that chalcones have as candidates for anti-leishmania drugs, and suggest that the CP04 compound may become a promising drug candidate to design and develop novel chalcone-based analogs for leishmaniosis therapy.

The first appearance of viruses can date back to the late last century. As an effective form of malware, viruses reside in the permanent storage of target hosts. Before a virus can execute, that must load into memory from the persistent storage included in the associated file. Due to the reliable destructive power of viruses, many mechanisms have been developed to defend computer systems against these hazardous threats. Antivirus software is one of the most famous and popular among these mechanisms. Most antivirus software uses static analysis (signature-based) technology on files stored in permanent storage, such as hard disks or USB flashes, to detect viruses hidden in files. Fileless malware was developed to enhance the survivability of malware by circumventing detection. Fileless malware only exists in the target hosts’ memory, not files. Antivirus software cannot even access the fileless malware code, much less analyze it, since it may be performed in memory directly without needing to load it from a disk. As a result, it is difficult for an antivirus engine to defend a system against fileless malware attacks. This paper proposes a kernel-based solution called Check-on-Execution (CoE) to detect fileless malware on a Linux system. When a program is going to execute a piece of code in a writable and executable memory area of a process, CoE suspends the code execution first. Coe retrieves the code from memory, packs the code with an ELF header to create an ELF file, and uses VirusTotal to check the file to prevent a Linux system from executing fileless malware. Experimental results show that CoE noticeably enhances the ability of a Linux system to defend itself again fileless malware. CoE is also suitable for protecting a system from shell code injection attacks, such as buffer and heap overflow attacks. It is capable of handling even packed malware. But in this paper, we only focus on fileless malware.

Oleanolic acid (OA) being the ubiquitous compound in the plant kingdom is studied for both the neuroprotective and neurotoxic properties. The mechanism of acetylcholinesterase (AChE) inhibitory potential of OA is investigated using the molecular dynamic simulations (MD) and docking as well as membrane-like and in vitro tests. There are also applied SH-SY5Y human neuroblastoma cells as well as in vivo on the zebrafish tests. The inhibitory potential towards the AChE enzyme is examined using the TLC-bioautography assay (the IC50 value is 9.22 μM). The CH- interactions between the central fragment of the ligand molecule and the aromatic cluster created by the His440, Phe288, Phe290, Phe330, Phe331, Tyr121, Tyr334, Trp84 and Trp279 side chains are observed. The in vitro tests carried out on the SH-SY5Y cells indicates that the viability rate is reduced to 71.5%, 61%, and 43% at the concentrations of 100 µg/mL, 300 µg/mL, and 1000 µg/mL, respectively after 48 hours of incubation whereas cytotoxicity against the tested cell line with the IC50 value is 714.32 ± 32.40 µg/mL. The in vivo tests on the zebrafish prove that there is no difference between the control and experimental groups as regards the mortality rate and morphology (P>0.05).

The traditional Simultaneous Localization and Mapping (SLAM) systems are based on the 1 strong static assumption, and their performance will degrade significantly due to the presence of 2 dynamic objects located in dynamic environments. To decrease the effects brought by the dynamic 3 objects, based on ORB-SLAM2 system framework, a novel dynamic semantic SLAM system called 4 MOR-SLAM is presented using mask repair method, which can accurately detect dynamic objects 5 and realize high-precision positioning and tracking of the system in dynamic indoor environments. 6 First, an instance segmentation module is added to the front end of ORB-SLAM2 to distinguish 7 dynamic and static objects in the environment and obtains a preliminary mask. Next, to overcome the 8 under-segmentation problem in instance segmentation, a new mask inpainting model is proposed to 9 ensure that the integrity of object masks, which repairs large objects and small objects in the image 10 with depth value fusion method and morphological method respectively. Then, a reliable basic matrix 11 can be obtained based on the above repaired mask. Finally, the potential dynamic feature points 12 in the environment are detected and removed through the reliable basic matrix, and the remaining 13 static feature points are input into the tracking module of the system to realize the high-precision 14 positioning and tracking in dynamic environments. The experiments on the public TUM dataset 15 show that, compared with ORB-SLAM2, the MOR-SLAM improves the absolute trajectory accuracy 16 by 95.55%. In addition, compared with DynaSLAM and DS-SLAM on the high-dynamic sequences 17 (fr3/w/rpy and fr3/w/static), the MOR-SLAM improves the absolute trajectory accuracy by 15.20% 18 and 59.71%, respectively

The purpose of this study was to compare Electromyographic (EMG) with Mechanomyo- 1 graphic (MMG) recordings during isometric conditions, and during a simulated load-lifting task. 2 Twenty-two males (age: 25.5 ± 5.3 years) first performed maximal voluntary contractions (MVC) and 3 submaximal isometric contractions of upper limb muscles at 25%, 50% and 75% MVC. Participants 4 then executed repetitions of a functional activity simulating a load-lifting task above shoulder level, 5 at 25%, 50% and 75% of their maximum activity (based on MVC). The low frequency part of the 6 accelerometer signal (< 5 Hz) was used to segment the 6 phases of the motion. EMG and MMG were 7 both recorded during the entire experimental procedure. Root mean square (RMS) and mean power 8 frequency (MPF) were selected as signal extraction features. During isometric contractions, EMG 9 and MMG exhibited similar repeatability scores. They also shared similar RMS vs force relationship, 10 with RMS increasing to 75% MVC and plateaued to 100%. MPF decreased with increasing force to 11 75% MVC. In dynamic condition, RMSMMG exhibited higher sensitivity to changes in load than 12 RMSEMG. These results confirm the feasibility of MMG measurements to be used during functional 13 activities outside the laboratory. It opens new perspectives for future applications in sports science, 14 ergonomics and human-machine interfaces conception.

The process of identifying and approving a new drug is a time-consuming and expensive procedure. One of the biggest issues to overcome is the risk of hepatotoxicity, which is one of the main reasons for drug withdrawal from the market. While animal models are the gold standard in preclinical drug testing, the translation of results into therapeutic intervention is often ambiguous due to interspecies differences in hepatic metabolism. The discovery of human induced Pluripotent Stem Cells (hiPSCs) and their derivatives has opened new possibilities for drug testing. We used mesenchymal stem cells and hepatocytes both derived from hiPSC, together with endothelial cells, to miniaturize the process of generating hepatic organoids. These organoids were then cultivated in vitro using both static and dynamic cultures. Additionally, we tested spheroids composed solely by induced hepatocytes. By miniaturizing the system, we demonstrated the possibility of maintaining the organoids, but not the spheroids, in culture for up to 15 days. This timeframe may be sufficient to carry out a hypothetical pharmacological test or screening. In conclusion, we propose that the hiPSC-derived liver organoids model could complement or, in the near future, replace the pharmacological and toxicological tests conducted on animals.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

The study considers building a dynamic model of profit maximization for the car-sharing system and its verification on the example of implementing such a system in Astana (Republic of Kazakhstan). The region, bounded by the administrative boundaries of Astana, was divided into subregions by covering the region with regular hexagons placed side by side. A dataset was built with information on 1168 trips to Astana from January to March 2023. The Kepler visualization service constructed maps of the beginning and end of trips in the region and a map of trips binding to the hexagonal grid cells. Each cell of the grid corresponds to a specific sub-region, for which the quantitative parameters necessary for solving the profit maximization problem in the car-sharing system are calculated. Stations with cars will be placed in the cells of the grid, which will be available to car-sharing service customers. Based on the collected data, a dynamic (four periods per day) and static profit maximization model in the car-sharing system was built. Modeling was carried out based on the built models in the example of Astana. It was established that using a dynamic model of profit maximization in the car-sharing system increases the profit by 3.7%.

The heterogeneous structure implies that a few nodes may be crucial in maintaining network structural and functional properties. Identifying these crucial nodes correctly and quickly is a primary issue as contemporarily may face the mushrooming of large-scale datasets. Besides, the ‘weight issue’ is always ignored in this field which edge weight may play a positive/negative role in contributing to the node importance in different weighted networks. This paper provides a novel algorithm, Weighted Expectation Algorithm (WEA), which aims to ensure accuracy and speed of computation by taking advantage of dynamic programming to better handle the task of large-scale networks. Additionally, the weight issue that edge weights may contribute differently is addressed by a simply quantitative definition. Two standard experiments show WEA can maintain the network structure in connectivity well (by the lowest average robustness 0.192) and identify the node importance better in the spreading function test of spreading dynamics (by the highest average Kendall’s tau-b 0.678). In addition, the time complexities of different algo-rithms are evaluated, and their time-consuming are tested, proving that WEA consumes a rela-tively short time.

A proxy war, between a coalition of countries, BLUE and a country, RED, is considered. RED wants to increase the size of the RED territory. BLUE wants to involve more regions in trade and other types of cooperation. GREEN is a small and independent nation that wants to become a member of BLUE. RED attacks GREEN and tries to invade. BLUE decides to give optimal arms support to GREEN. This support can help GREEN in the war against RED and simultaneously reduce the military power of RED, which is valuable to BLUE, also outside this proxy war, since RED may confront BLUE also in other regions. The optimal control problem of dynamic arms support, from the BLUE perspective, is defined in general form. The objective function is a weighted sum of the present value of the free GREEN territory and the present value to BLUE of the net loss of military resources in the RED army. The net loss of RED at a particular point in time is a function of the location of the front line and the size of the mobile GREEN forces behind the RED line. First, it is assumed that the expected net loss is proportional to the force ratio behind the red front line. It is proved that the net loss function is a strictly concave quadratic function of x, the location of the front line. It is also proved that the unique maximum of the net loss function occurs at the same front location, also if the net loss function is proportional to the strength ratio behind the RED lines, raised to any strictly positive exponent. From the BLUE perspective, there is an optimal position of the front. This position is a function of the weights in the objective function and all other parameters. Optimal control theory is used to determine the optimal dynamic BLUE strategy, conditional on a RED strategy, which is observed by BLUE military intelligence. The optimal arms support strategy for BLUE is to initially send a large volume of arms support to GREEN, to rapidly move the front to the optimal position. Then, the support should be almost constant during most of the war, keeping the war front location stationary. In the final part of the conflict, when RED will have almost no military resources left and tries to retire from the GREEN territory, BLUE should strongly increase the arms support and make sure that GREEN rapidly can regain the complete territory and end the war

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

This article is a theoretical contribution to mental model research, which currently has different threads. Whereas some researchers focus on the perceived causal structure, others also include decision policies and decisions. We focus on the link between recognized causal structure (“mental models of dynamic systems”) and policies, proposing Johnson-Laird’s theory of mental models as the link. The resulting framework hypothesizes two types of systematic mental model errors: (1) misrepresentation of the system’s structure and (2) failure to deploy relevant mental models of possibilities. Examination of three experiments through this lens reveals errors of both types. Therefore, we propose that the cognitive theory of mental models opens a path to better understand how people construct their decision policies and develop interventions to reduce such mental model errors. The article closes by raising several questions for empirical studies of the reasoning process leading from mental models of dynamic systems to decision policies.

Oncogenic protein E6 from Human Papilloma Virus 16 (HPV-16) mediates the degradation of Membrane-associated guanylate kinase with inverted domain structure-1 (MAGI-1), throughout the interaction of its protein binding motif (PBM) with the Discs-large homologous regions 1 (PDZ1) domain of MAG1-1. Generic variation in the E6 gene that translates to changes in the protein’s amino acidic sequence modifies the interaction of E6 with the cellular protein MAGI-1. MAGI-1 is a scaffolding protein found at tight junctions of epithelial cells, where it interacts with a variety of proteins regulating signaling pathways. MAGI-1 is a multidomain protein containing two WW (rsp-domain-9), one guanylate kinase-like, and six PDZ domains. PDZ domains played an important role in the function of MAGI-1 and served as targets for several viral proteins including the HPV-16 E6. The aim of this work was to evaluate, with an in silico approach, employing molecular dynamics simulation and protein-protein docking, the interaction of the intragenic variants E-G350 (L83V), E-C188/G350 (E29Q/L83V), E-A176/G350 (D25N/L83V), E6-AAa (Q14H/H78Y/83V) y E6-AAc (Q14H/I27RH78Y/L83V) and E6-reference of HPV-16 with MAGI-1. We found that variants E-G350, E-C188/G350, E-A176/G350, AAa and AAc increase their affinity to our two models of MAGI-1 compared to E6-reference.

Objectives: To investigate the value of early lactate dynamic monitoring index in predicting prognosis of patients with sepsis and septic shock. Methods: We performed our test on 50 patients. Out of 50 patients, 28 are male, and 22 are female. Prospectively studied pediatric patients with septic shock were performed. Vital signs, Lactate clearance, were obtained at presentation 6 h, 12 h, 24 h over the first 48 h of hospitalization. The therapy received, outcome parameters of mortality and duration of hospitalization were recorded. Results: The statistical data and comparative analysis showed that an average of 16.88 days after admission, 5 patients have died, 17 patients are poorly prognosis leaves the hospital, and the remaining 28 are recovered and discharged. The primary outcome variable of mean 16 days hospitalization mortality rate was 10%. Poor prognosis 34% and fully recovery 56 % were observed. In this retrospective cohort study, a lactate level of more than 2.5mmol/L was the best threshold to predict 28-day mortality among severe sepsis and septic shock patients. In our research, we found mean LC 6 h 3.08mmol/L, and after 48 h mean it is 1.79mmol/L. Significant LC 6 h found, which is 8.08mmol/L in the death group patient where 48 h mmol/L shows significant high. Poor prognosis also presents a clinical increase of lactate level high in the LC 6 h analysis, which is 3.32mmol/L. Recovered patients showed a significant improvement after administering treatment depending on the patient organ involvement and good decrease of lactate reports achieved, which is 1.20mmol/L, where admission reports show it was 1.91mmol/L in LC 6 h. Mean Heart rate 94/51mmhg, pulse 119, temperature 39℃, respiratory rate 32.26, and urine output 456 ml recorded during our study. Death patient shows a remarkable detonation of those reports but has a significant clinical report with the recovered patients. Conclusion: The early lactate dynamic monitoring index has a high value in predicting sepsis and septic shock patients' prognosis, thus worth popularizing.

It is challenging to apply heat flow through a thermal bridge, which requires the analysis of 2D or 3D heat transfer to building energy simulation(BES). Research on the dynamic analysis of thermal bridges has been underway for many years, but their utilization remains low in BESs. This paper proposes a thermal bridge modeling and a dynamic analysis method that can be easily applied to BESs. The main idea begins with an analogy of the steady-state analysis of thermal bridges. As with steady-state analysis, the proposed method first divides the thermal bridge into a clear wall, where the heat flow is uniform, and the sections that are not the clear wall (the thermal bridge part). For the clear wall part, the method used in existing BESs is applied and analyzed. The thermal bridge part (TB part) is modeled with the linear time-invariant system (LTI system) and the system identification process is performed to find the transfer function. Then, the heat flow is obtained via a linear combination of the two parts. This method is validated by comparing the step, sinusoidal and annual outdoor temperature response of the finite differential method(FDM) simulation. When the thermal bridge was modeled as a third-order model, the root mean square error(RMSE) of annual heat flow with the FDM solution of heat flow through the entire wall was about 0.1W.

In this paper, drug treatment and vaccination are compared healthy and economically. In this comparison, in addition to comparing economic costs, it has paid attention to patients' recovery. To reach the goal, the prevalence of Covid-19 virus in New York is modeled by using the SEIR dynamic model. The SEIR dynamic model is used to model the period of epidemic diseases. Then, three disease control scenarios are evaluated economically. Treatment and vaccination are two important issues in controlling epidemic diseases. To control the disease, each of these two methods has economic costs and benefits. The main purpose of this paper is to compare the two methods of vaccination and treatment economically. Although the results of the study show that vaccination can be effective in preventing the epidemic of the disease than treatment, but due to the high cost and genetic mutation of the virus, vaccination is not the optimal method for both health and the economy in the long term.

China is not only short of fresh water resources per capita, but also faces a serious problem of water pollution in recent years, with 190 million people suffering from excessive levels of harmful substances in their drinking water. Such as arsenic poisoning and fluorosis and other endemic water diseases high incidence. As a series of water pollution prevention plan of action by the Chinese government announced that, this paper uses the modified Undesirable Dynamic Network model empirical analysis of China's 31 provincial administrative region economic growth, wastewater treatment, and water disease control efficiency between 2013 and 2017. The results show that the efficiency of water pollution disease in all four regions of China and the total efficiency in the three regions of east, west and central China all show a decreasing trend, and the efficiency scores and rankings of all provinces and cities within the region fluctuate greatly. The eastern region with the most developed economy has the best overall performance, with higher efficiency in Water consumption and Water disease control. However, the efficiency of wastewater treatment in northeast China is stable and better. Given the high level of economic development in China and the results of the above mentioned efficiency in water pollution and water diseases, improving the efficiency and quality of wastewater treatment in China is regarded as an important factor in achieving the strategic goal of green growth.

This paper puts forward an alteration for Tensor Calculus utliized in a coordinate system which is under a dynamic distortion drawing inspiration from similar fields such as the Calculus of Moving Surfaces (CMS). The paper establishes transformation laws for Tensors within these regions and establishes Operators such as the Tensorial Field Derivative which enforce a Tensorial Transformation on Tensors defined within a Dynamically Moving coordinate system. This variation of Tensor Calculus can be utilized to observe how disciplines such as QFT and Continuum Mechanics would change to accomodate for a distorting coordinate system and can be utliized to develop new theoretical models which account for this temporal distortion particularly within Biological Settings.

This paper presents performed Ansys numerical simulation on WindFloat structures. It contributes to the methodology of calculation based on CFD instruments to study the movements of the waves on semi-submersible stationary structures and highlights the importance of using RAO functions. RAO numerical approach developed can be applied to design semisubmersible WindFloat structures in order to fulfill essential requirements regarding operational safety and design. Numerical methodology was designed in accordance marine loads and the I.T.T.C. recommendations. The numerical RAO results for regular wave movements include many elements for the semi-submergible structure. Close results to open sea operation can be achieved by constant improvement in numerical simulation methodologies. The work opens the way for further hydrodynamic development on irregular waves for realistic hydrodynamic and structural response of the actual semi-submersibles at sea. The results demonstrate the accuracy of RAO function approach for specific WindFloat in Jonswap spectrum.

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

The excessive vibration caused by crowds walking across footbridges has attracted great public concerns in the past few decades. This paper presents, from considering the dynamic characteristics of the bipedal crowd model, a new stability limit criterion based on the bipedal excitation model. The stability limit can be used to estimate the upper boundary of crowd size. In addition, the dynamic stable performances of a structure, under a certain walking crowd size, can be predicted by the stability criterion. This proposed mechanism provides an alternative comprehension how crowd excite the excessive sway motion with a large-span structure.

Websites and applications use personalisation services to profile their users, collect their patterns and activities and eventually use this data to provide tailored suggestions. User preferences and social interactions are therefore aggregated and analysed. Every time a user publishes a new post or creates a link with another entity, either another user, or some on-line resource, new information is added to the user profile. Exposing private data does not only reveal information about single users' preferences, increasing their privacy risk, but can expose more about their network that single actors intended. This mechanism is self-evident on \emph{social networks} where users receive suggestions based on their friends' activity. We propose an information theoretic approach to measure the differential update of the anonymity risk for time-varying user profiles. This expresses how privacy is affected when new content is posted and how much third party services get to know about the users when a new activity is shared. We use real Facebook data to show how our model can be applied on a real world scenario.

Herein we report the expansion of the chemical space available from the chitin, accessible via the biogenic N-platforms 3A5AF, M4A2C and di-HAF. The biologically active heteroaromatics furo[3,2-d]pyrimidin-4-one and furo[3,2-d]pyrimidin-4-amine can be selectively accessed from 3A5AF and M4A2C, respectively. The chiral pool synthon di-HAF is a viable substrate for the Achmatowicz rearrangement, providing streamlined access to 2-aminosugars possessing a versatile hydroxymethyl group at C5.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

The aim of this study was to investigate the impact of Process Oriented Guided Inquiry Learning (POGIL)-based instruction versus lecture-based instruction on Grade 12 students’ performance in circular motion unit. A quasi-experimental, pretest-posttest design, the impact of POGIL-based instruction versus lecture-based instruction on students’ performance as measured by three types of cognitive outcomes: Knowing, Applying and Reasoning (KAR). The total number of participants was approximately 110 students (N=110); 54 were assigned to treatment groups (25 girls and 29 boys) and 56 were assigned to control groups (27 girls and 29 boys). The treatment group was taught a unit of circular motion in physics using POGIL-based instruction while the control group was taught the unit using lecture-based instruction. The findings of the study showed statistically significant differences between students of the control group and the treatment group in favor of the later regarding their circular motion performance, suggesting the superiority of the POGIL in enhancing student understanding of the circular motion.

This article investigates the prospect of implementing multidisciplinary and multicultural student teamwork (MMT) involving Case-based Learning (CBL) and Problem-based Learning (PBL) as a sustainable teaching practice. Based on a mixed methods approach, which includes direct observation (both physical and virtual), questionnaire distribution and focus-group interviews the study reveals that MMT through CBL and PBL can both facilitate and hinder sustainable learning. Our findings show that while MMT enhances knowledge sharing, it also poses a wide range of challenges, raising questions about its social significance as a sustainable teaching practice. The study suggests the implementation of certain mechanisms, such as ‘Teamwork Training’ and ‘Pedagogical Mentors’, aiming to strengthen the sustainable orientation of MMT through CBL and PBL.

In MBSE there is yet no converged terminology. The term ’system model’ is used in different contexts in literature. In this study we elaborated the definitions and usages of the term ’system model’, to find a common definition. 104 publications have been analyzed in depth for their usage and definition as well as their meta-data e.g., the publication year and publication background to find some common patterns. While the term is gaining more interest in recent years it is used in a broad range of contexts for both analytical and synthetic use cases. Based on this three categories of system models have been defined and integrated into a more precise definition.

This article discusses the use of game design as a method for interdisciplinary project-based teaching in secondary school education to convey informatics and society topics. There is a lot of knowledge about learning games but little background on project-based teaching using game design as a method. We present the results of an analysis of student-created games and an evaluation of a student-authored database on learning contents found in commercial off-the-shelf games. We further contextualise these findings using a group discussion with teachers. Results underline the effectiveness of project-based teaching to raise awareness for informatics and society topics. We further outline informatics and society topics that are particularly interesting to students, genre preferences and potentially engaging game mechanics stemming from our analyses.

The ubiquity of mobile sensors (such as GPS, accelerometer and gyroscope) together with increasing computational power have enabled an easier access to contextual information, which proved its value in next generation of the recommender applications. The importance of contextual information has been recognized by researchers in many disciplines, such as ubiquitous and mobile computing, to filter the query results and provide recommendations based on different user status. A context-aware recommendation system (CoARS) provides a personalized service to each individual user, driven by his or her particular needs and interests at any location and anytime. Therefore, a contextual recommendation system changes in real time as a user’s circumstances changes. CoARS is one of the major applications that has been refined over the years due to the evolving geospatial techniques and big data management practices. In this paper, a CoARS is designed and implemented to combine the context information from smartphones’ sensors and user preferences to improve efficiency and usability of the recommendation. The proposed approach combines user’s context information (such as location, time, and transportation mode), personalized preferences (using individuals past behavior), and item-based recommendations (such as item’s ranking and type) to personally filter the item list. The context-aware methodology is based on preprocessing and filtering of raw data, context extraction and context reasoning. This study examined the application of such a system in recommending a suitable restaurant using both web-based and android platforms. The implemented system uses CoARS techniques to provide beneficial and accurate recommendations to the users. The capabilities of the system is evaluated successfully with recommendation experiment and usability test.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

This paper presents a limited scope dynamic probabilistic risk assessment (D-PRA) on the survivability of commercial of the shelf (COTS) drones tasked with surveilling areas with varying radiation levels after a nuclear accident. The D-PRA is based on a discrete-dynamic event tree (D-DET) approach, which couples with the OpenEPL error propagation framework to model sequences leading to Loss of Mission (LOM) scenarios due to component failures in the drone’s navigation system. Radiation effects are simulated by calculating the total ionizing dose (TID) against the permissible limit per component, and errors are propagated within the electronic hardware and software blocks to quantify navigation system availability per radiation zone. The proposed methods are integrated into the traditional event tree/fault tree approach and the most vulnerable components are radiation-hardened (RAD-HARD) to the extent specified by a predefined mission success criterion. The results demonstrate the usefulness of the proposed approach in performing trade studies for incorporating COTS components into RAD-HARD drone designs.

Hospital-based programs democratize mRNA therapeutics by facilitating the processes to translate a novel RNA idea from the bench to the clinic. Because mRNA is essentially biological software, therapeutic RNA constructs can be rapidly developed. The generation of small batches of clinical grade mRNA to support IND applications and first-in-man clinical trials, as well as personalized mRNA therapeutics delivered at the point-of-care, is feasible at a modest scale of cGMP manufacturing. Advances in mRNA manufacturing science and innovations in mRNA biology, are increasing the scope of mRNA clinical applications.

Mechanical equipment is composed of several parts, the interaction between the parts exists throughout whole life cycle leads to the widespread phenomenon of fault coupling and the diagnosis of independent faults cannot meet the requirements of the health management of mechanical equipment under actual working conditions. In this paper, the topological structure of graph neural network is used to describe the correlation of coupling faults and multiple fault types are regarded as network nodes respectively. The fault features are fused and extracted by graph convolution to achieve the classification of coupling faults. In this paper, dynamic vertexes are defined in data topology and the parameters of DIGNN classification model are optimized by changing the fault type of dynamic vertexes during training stage. The data is loaded into dynamic vertexes for classification and analysis during testing stage. The one-dimensional vibration data is converted into two-dimensional time-frequency domain data by wavelet transform making the input features of the model interpretable to reduce the uncertainty of model training. The data topology is then fed into DIGNN for fault classification, and GCN's node aggregation gives interpretability to each layer of network data processing. The method proposed in this paper can realize accurate diagnosis of independent faults on the data set, and can effectively judge the coupling mode of coupling faults, which is suitable for coupling fault analysis of mechanical equipment.

Dynamic time history analysis is a powerful and effective method to study the seismic response of tunnels, the dynamic time history to analyze the seismic response of the tunnel in the typical subway in this paper. The analysis results show that the overall levelling of the tunnel will not affect the tunnel too much, and the seismic response of the tunnel is mainly related to the relative displacement of the ground around the tunnel. The analysis results show that the internal force of the tunnel and the tunnel inclination have a good linear relationship, and the tunnel inclination can be used to measure the magnitude of the seismic response of the tunnel.

The advancement of autonomous capabilities in maritime navigation has gained significant attention, with a trajectory moving from decision support systems to full autonomy. This push towards autonomy has led to extensive research focusing on collision avoidance, a critical aspect of safe navigation. Among the various possible approaches, Dynamic Programming is a promising tool for optimizing collision avoidance maneuvers. This paper presents a DP formulation for collision avoidance of autonomous vessels. We set up the problem framework, formulate it as a multi-stage decision process, define cost functions and constraints focusing on the actual requirements a marine maneuver must comply with, and propose a solution algorithm leveraging parallel computing. Additionally, we present a greedy approximation to reduce algorithm complexity. Through case studies, we demonstrate the effectiveness of the proposed approach in navigating complex scenarios, contributing to the future of autonomous maritime navigation. Through case studies, we show the efficacy of our approach in navigating complex scenarios.

Photovoltaic shading devices (PVSDs) have the dual function of providing shade and generating electricity, which can reduce building energy consumption and improve indoor daylighting levels. This study adopts a parametric performance design method and establishes a one-click simulation process by using the Grasshopper platform and Ladybugtools. The research focuses on the effect of dynamic PVSDs on daylighting and energy consumption in an office building in Qingdao. Through simulation, the study calculates the monthly energy consumption and useful daylight illuminance (UDI) under different inclination angles and installation heights of PVSDs. And the optimal configuration of PVSDs for each month under three dynamic strategies (rotation, sliding, and hybrid) is determined. Additionally, different control strategies and fixed PVSDs are compared to clarify the impact of various control strategies on daylighting and energy consumption. The findings reveal that, compared to no shading, dynamic PVSDs in rotation strategy (with an installation height of 0 m), sliding strategy (with an inclination angle of 20°), and hybrid strategy can achieve energy savings of 32.13%, 47.22%, and 50.38%, respectively. They can increase the annual average UDI by 1.39%, 2.8%, and 3.1%, respectively.

In recent years, both domestic and international research on quadruped robots has advanced towards high dynamics and agility, with a focus on high-speed locomotion as a representative motion in high-dynamic activities. Quadruped animals like cheetahs exhibit high-speed running capabilities, attributed to the indispensable role played by their flexible spines during the flight phase motion. This paper establishes dynamic models of quadruped robots with different degrees of spine flexibility, providing a parameterized description of the flight phase motion for both rigid trunks and flexible spine quadruped robots. By setting different initial values for the spine joint and calculating the flight phase results for both types of robots at various initial velocities, the study compares and analyzes the impact of a flexible spine on the flight phase motion of quadruped robots. Through comparative experiments, the research aims to validate the influence of a flexible spine during the flight phase motion, providing insights into how spine flexibility affects the flight phase motion of quadruped robots.

The dynamic factors in the environment violate the static environment assumption of the SLAM algorithm, leading to a decrease in the accuracy of camera positioning. In recent years, many studies have attempted to address dynamic objects by combining semantic constraints and geometric constraints, but issues such as poor real-time performance, the potential for mistakenly treating humans as rigid objects, and subpar performance in high-dynamic scenes still persist. This paper proposes a dynamic scene visual SLAM algorithm called Dynamic SLAM based on target tracking and multi-view geometry (TKG-SLAM), based on object detection, Kalman filters, and multi-view geometry. This algorithm takes into consideration both real-time performance and algorithm accuracy. It combines semantic constraints and multi-view geometry constraints, selectively running the algorithm in different scenarios, filtering and preserving static points for camera pose estimation. Experimental results demonstrate that, compared to current state-of-the-art dynamic SLAM methods, our approach achieves optimal performance in some scenarios and exhibits stronger real-time capabilities.

The proliferation of ransomware poses a significant threat to global cybersecurity. This study presents a comprehensive review of the methodologies employed in the detection and analysis of ransomware, emphasizing the dichotomy between static and dynamic analysis approaches. It introduces the historical context and the necessity for robust cybersecurity measures, followed by an outline of the methodological framework used to evaluate existing ransomware analysis techniques. The results detail the effectiveness and limitations of various analysis strategies, identifying key features and patterns that aid in the detection and classification of ransomware threats. The study concludes by summarizing the primary achievements, including the identification of gaps in current research and proposing future research directions aimed at enhancing ransomware detection and mitigation strategies. The synthesis provided in this survey offers a consolidated view of the state-of-the-art in ransomware threat analysis and serves as a resource for cybersecurity professionals and researchers.

: In this paper, we examine potential methods for autonomously tracking and landing multi-rotor unmanned aerial vehicles (UAVs), a complex yet essential problem. Autonomous tracking and landing control technology utilizes visual navigation, relying solely on vision and landmarks to track targets and achieve autonomous landing. This technology improves the UAV's environment perception and autonomous flight capabilities in GPS-free scenarios. In particular, we are researching tracking and landing as a cohesive unit, devising a switching plan for various UAV tracking and landing modes, and creating a flight controller that has an inner and outer loop structure based on relative position estimation. The inner and outer nested markers aid in the independent monitoring and touchdown of UAV. Optimal parameters are determined via optimized experiments on the measurements of the inner and outer markers. An indoor experimental platform for tracking and landing UAV was established. Tracking performance was verified by tracking three trajectories of unmanned ground vehicle (UGV) at varying speeds, and landing accuracy was confirmed through static and dynamic landing experiments. The experimental results show that the proposed scheme has good dynamic tracking and landing performance.

Porous metals possess low bulk density, large specific strength, high stiffness and special thermal, electromagnetic and acoustic conductivity, so that porous metals are widely used in filtration and separation, flame retardant explosion-proof, biomedical application, etc. Compared with its corresponding dense metal, the presence of porous structures also leads to different corrosive performances of porous metal. So, some researches have utilized weight loss method, electrochemical impedance to evaluate porous metals’ corrosion behavior; however, the influence of pore structure on metal corrosion is still controversial, and present methods used for analyses of porous metals’ corrosion are statistical averages of the corrosion behavior of the entire porous material, which cannot accurately reflect the corrosion behavior inside the pore structure. Herein, we prepare porous copper samples with 0, 24, 72, 96 pores using mechanical process, and employ scanning kelvin probe combined with electrochemical polarization curve and impedance spectroscopy to test the corrosion performance of the porous copper in static and dynamic NaCl solution. The relevant results indicate that in static solution, the corrosion resistance of samples gradually increases with the rise of the number of pores. By contrast, the sample with 24 pores exhibits more susceptible to corrosion than the sample without pore.

The utilization of primary school buildings is multifaceted, primarily due to the high occupancy density, varying thermal preferences among occupants, diverse indoor activities (such as walking, sports, and conversation), and a constant flow of individuals entering and exiting the building. This results in frequent opening and closing of external windows and doors and fluctuations in internal heat gain. Consequently, frequent interactions between the indoor and outdoor microenvironments lead to energy losses. This study conducts a comprehensive literature review on building energy loss stemming from occupant behavior and the interactions between indoor and outdoor microenvironments. Furthermore, it proposes a dynamic real-time monitoring system based on a computer data capture and visualization platform foundation for building energy loss. The research methods include data crawling, data association rule mining, and data association analysis. The research findings yield a universally applicable and informative building energy-saving design theory based on extensive data analysis. Additionally, the system presents information on occupants' behavior and the microclimate data of indoor and outdoor environments on a computer screen, facilitating human-machine communication and enabling timely adjustments to design strategies for new buildings and operation and maintenance strategies for existing buildings.

We propose a method of cooling nuclear spin systems of solid-state nanostructures by application of a time-dependent magnetic field synchronized with spin fluctuations. Optical spin noise spectroscopy is considered as the method of fluctuation control. Depending on the mutual orientation of the oscillating magnetic field and the probe light beam, cooling might be either provided by dynamic spin polarization in an external static field or result from population transfer between spin levels without build-up of a net magnetic moment (“true cooling”).

Power and energy efficiency are among the most crucial requirements in high-performance and other computing platforms. This work examines through extensive experimentation methods and procedures suitable for assessing the power and energy efficiency of fundamental hardware building blocks inside a typical high-performance CPU, focusing on the dynamic branch predictor (DBP). The investigation relies on the Running Average Power Limit (RAPL) interface from Intel, a software tool for credibly reporting the power and energy based on instrumentation inside the CPU. We use well-known microbenchmarks under various run conditions to explore potential pitfalls and to develop precautions to raise the precision of the measurements obtained from RAPL for more reliable power estimation. The authors discuss the factors that affect measurements and share the difficulties encountered and the lessons learned.

As we all know, many more dynamic objects appear almost continuously in real world, which are immensely able to impair the performance of the majority of vision-based SLAM systems that are based on the static-world assumption. In order to improve the robustness and accuracy of visual SLAM in the high dynamic environment, a real-time and robust stereo SLAM system for dynamic scenes was proposed. To weaken influences of dynamic content, the moving object detection method was put forward in our visual odometry, then the semantic segmentation network was combined into our stereo SLAM to extract pixel-level contours of dynamic objects. Then influences of dynamic objects were extremely weaken and the performance of our system was increased markedly in dynamic, complex and crowed city spaces. Experiment with both on KITTI Odometry dataset and in a real-life scene, the results show that our method can dramatically decrease the tracking error or drift, improve the robustness and stability of our stereo SLAM in high dynamic outdoor scenarios.

Considering the dynamic stall effects in engineering calculations is essential for correcting the aerodynamic loads acting on wind turbines, both during power production and stand-still cases, and impacts significantly the turbine aeroelastic stability. The employed dynamic stall model needs to be accurate and robust for a wide range of airfoils and range of angle of attack. The present studies are intended to demonstrate the performance of a recently implemented "IAG dynamic stall" model in a wind turbine design tool Bladed. The model is transformed from the indicial type of formulation into a state-space representation. The new model is validated against measurement data and other dynamic stall models in Bladed for various flow conditions and airfoils. It is demonstrated that the new model is able to reproduce the measured dynamic polar accurately without airfoil specific parameter calibration and has a superior performance compared to other models in Bladed.

In recent years, the production of renewable energy represents one of the main challenges of modern and future society. The new cultivation method called Agrivoltaic (hereafter AV), combines and associates agricultural production and renewable energy (photovoltaic) production in a collaborative synergy from which both benefit. In this study, the dry matter and essential oils yield of six medicinal species (Salvia officinalis L., Origanum vulgare L., Rosmarinus officinalis L., Lavendula angustifolia L., Thymus citriodorus L. and Mentha spicata L.) grown underneath a dynamic AV system in comparison to those in full sun (T), were evaluated. In particular, below the dynamic AV system, due to the rotation of the panels, two plot areas on the ground were distinguished: one always covered by the panels (UP), and another one covered alternatively (BP). During the aromatic crop cycles, the solar radiation, infrared leaf temperature and air temperatures in UP, BP and T plot, were measured. In addition, at harvest time, weed survey was carried out. The results showed that, in general, the solar radiation and infrared leaf temperature were lower in UP plot than in either the BP and T plots, while the air temperatures were similar in all compared plots. Also the weed cover percentage was lower in the UP plot than other ones. The essential oils yield in the sage, thyme, mint and rosemary plants were higher in both UP and BP plots than for T plot. Thus, shading and/or less weed infestation may have been the main factors favorably influencing the performance of medicinal crops under a dynamic AV system.

Dynamic Realistic Failure Process Analysis (DRFPA) is a numerical software based on FEM it is firstly validated by comparing with the experimental test. Such validation is carried out under two consistent concrete specimens under uniaxial compression. After validation, DRFPA is used to study the influence of two parallel pre-existing crack inclination angles on the fracture of concrete under dynamic loads. The evolution of wing cracks and secondary cracks is investigated by observing the initiation, coalescence, and propagation of them. Meanwhile, the relationship between failure mode and inclination angles is discussed via analyzing the acoustic emission events. Finally, it is concluded the relationship between inclination angles of pre-cracks and performance/stability of concrete structure.

Human behaviour was tipped as the mainstay in the control of further SARS-CoV-2 (COVID-19) spread especially after the lifting of restrictions by many countries. Countries in which restrictions were lifted soon after the first wave, had subsequent waves of the COVID-19 infections and it remains to be seen whether there will be more waves. In this paper, we formulate a deterministic model for COVID-19 incorporating dynamic non-pharmaceutical interventions, dubbed social dynamics. The model steady states are determined and their stability analysed. Numerical simulations are carried out to determine the pack of various parameters that influence the social dynamics. In South Africa, the first wave was the only wave in which the only interventions rested solely on human behavior. The model is thus fitted to COVID-19 data on the first wave in South Africa. The results presented in this paper have implications on the trajectory of the pandemic in the presence of changing social processes.

One of the central criteria for free will is “Could I have done otherwise?” But because of a temporal asymmetry in human choice, the question makes no sense. The question is backward-looking, while human choices are forward-looking. At the time when any choice is actually made, there is as of yet no action to do otherwise. Expectation is the only thing to contradict (do other than). So the ability to do something not expected by the ultimate expecter, Laplace’s demon, is a better criterion for free will. If human action is fundamentally unpredictable, then we have free will. Scientists have studied a form of fundamental unpredictability, known as undecidability. The features that make a system capable of undecidable dynamics have been identified: program-data duality; potential to access an infinite computational medium; and the ability to implement negation. Humans have all three of these features, so we very likely are fundamentally unpredictable, so we have free will.

The fault diagnosis of the gearbox is primarily based on the analysis of the harmonic response. However, the generation mechanism of the harmonic response of the gear pair is still not distinctly explained in a healthy gearbox. Therefore, this paper is dedicated to establishing a dynamic model of the gearbox for this issue. In this model, the contact force of the bearing and the meshing stiffness of the gear pair are determined by the Hertz theory and the potential energy method, then the shaft motion is used as the connection to establish the coupling relationship between the gear pair and the bearing. After this dynamic model is confirmed by experiments and existing models, the coupling relationship inside the gearbox and the harmonic response of the gear pair are studied using this model. The result demonstrates that a closed control loop is formed due to the vibration transmission between the gear pair, the bearing and the shaft, and there is a strong coupled vibration between the gear pair and the bearing in the gearbox. Due to the generation of the center distance error, misalignment angle and disorganized meshing process of the gear pair, the meshing stiffness is altered, which excites the harmonic response of the gear pair. When the speed of the gearbox is increased, although the vibration amplitude of the gearbox is increased, the system predominantly vibrates at the fundamental frequency, and the harmonic of the gear pair is also shifted to the low frequency band.

Emergence of multi drug resistant (MDR) and extensively drug resistant (XDR) Mycobacterium tuberculosis poses a serious threat to TB control as the available treatment options are less effective in these cases. Therefore, new strategies are required for identification of new drugs and drug targets. The M. tuberculosis dihydrodipicolinate synthase is a putative drug target with no potent inhibitor. Here in this study, we have used a comprehensive computational approach to identify small molecule inhibitors and validated them in vitro. As similar structures tend to have similar functions, therefore 3 approaches, namely, (a) known inhibitor-based approach, (b) substrate analogues, (c) product analogues were used for compound screening from various chemical libraries. The fourth approach we have taken is fragment library screening.In vitro studies revealed that β-hydroxypyruvic acid tartronic acid are inhibitors of Mtb-rDapA with maximum inhibition 48% and 51% at 500µM concentrations respectively. We have also observed that β-hydroxypyruvic acid is a time dependent inhibitor of Mtb-rDapA. Further, thermal shift assays showed that β-hydroxypyruvic acid interacts with Mtb-rDapA and the thermal stability of Mtb-rDapA shifted by 3˚C. Among the product analogues of Mtb-DapA, dipicolinic acid showed to bind to Mtb-rDapB shifting thermal stability of Mtb-rDapB by 0.5˚C in binding. Additionally, we have designed a new approach by combining substrate and product analogues to achieve better inhibitions. In vitro assays validated that this combination approach increased maximum inhibition up to 100%. We envision that these compounds would serve as potent leads for tuberculosis drug discovery.

The optoelectronic properties of free standing monolayer (ML) hexagonal boron nitride (h-BN) is investigated for potential solar energy conversion applications using the Density Functional Theory (DFT) full potential linearized augmented plane wave (FP-LAPW) method. In addition, the bulk optical properties have also been calculated for the sake of comparison. The dielectric functions, optical conductivities and the optical constants are evaluated using the relaxed structures from electronic total energy pseudopotential calculations. The results reinforce previous research on h-BN DUV optoelectronics and demonstrate the suitability of its use as a component in deep ultraviolet (DUV) and energy conversion devices.