A topical challenge for algorithms in general and for automatic image categorization and generation in particular is presented with the aim of highlighting strengths and deficiencies of current Artificial Intelligence approaches while sketching a way forward. A general lack of encompassing symbol-embedding and (not only) -grounding in some bodily basis is made responsible for current deficiencies. A concomitant dearth of hierarchical organization of concepts follows suite. As a remedy for these shortcomings, it is proposed to take a wide step back and to newly incorporate aspects of cybernetics and analog control processes. It is claimed that a promising overarching perspective is provided by the Ouroboros Model with a valid and versatile algorithmic backbone for general cognition at all accessible levels of abstraction and capabilities.

Target recognition mainly includes three approaches: optical image-based, echo detection-based, and passive signal analysis-based methods. Among them, the passive signal-based method is closely integrated with practical applications due to its strong environmental adaptability. Based on passive radar signal analysis, we design an "end-to-end" model that cascades a noise estimation network with a recognition network to identify working modes in noise environment. The noise estimation network is implemented based on U-Net, which adopts a method of feature extraction and reconstruction to adaptively estimate the noise mapping level of the sample, which can help the recognition network to reduce noise interference. Focusing on the characteristics of radar signal, the recognition network is realized based on Multi-Scale Convolutional Attention Network (MSCANet). Firstly, the deep group convolution is used to isolate the channel interaction in the shallow network. Then, through the multi-scale convolution module, finer-grained features of the signal are extracted without increasing the complexity of the model. Finally, the self-attention mechanism is used to suppress the influence of low-correlation and negative-correlation channels and spaces. This method overcomes the problem that the conventional method is seriously disturbed by noise. We validated the proposed method in 81 kinds of noise environments, achieving an average accuracy of 94.65%. Additionally, we discussed the performance of six machine learning algorithms and four deep learning algorithms. Compared to these methods, proposed MSCANet achieved an accuracy improvement of approximately 17%. Our method demonstrates better generalization and robustness.

The buildup dynamics of diode-pumped passively mode-locked solid-state laser is thoroughly explored by the real-time measurement with temporal sampling rate up to 40 GHz. A concise cavity is developed to ensure the transient dynamics purely arising from the gain medium and saturable absorber. Experimental results reveal that the laser output in the buildup process exhibits numerous passively Q-switched pulses followed with a damped relaxation oscillation prior to the stable mode locking. Furthermore, it is confirmed that the laser output has already displayed single clean mode-locked pulses inside the first several Q-switched envelopes before stepping into the stage of relaxation oscillation. The present real-time exploration is expected to provide important information for practical applications with temporal modulation of the pump intensity.

We present here a theory of Majorana excitons, photo-excited conduction electron-valence band hole pairs, interacting with Majorana Fermions in a Kitaev chain of semiconductor quantum dots embedded in a nanowire. Using analytical tools and exact diagonalisation methods we identify the presence of Majorana Zero Modes in the nanowire absorption spectra.

The technology of left ventricular assist devices (LVADs) requires developing and implementing an intelligent control systems to optimize pump speed to achieve a physiological metabolic demands for heart failure (HF) patients. This work aimed to present an advanced control algorithm to drive an LVAD under different physiological conditions. Pole placement method in conjunction with of sliding mode control approach (PP-SMC) was utilized to design and construct the proposed control method. In this design, the method was adopted to use neural networks to eliminate system uncertainties of disturbances. An elastance function was also developed and used as an input signal to mimic the physiological perfusion of HF patients. Two scenarios ranging from rest to exercise were introduced to evaluate the proposed technique. In this technique, a lumped parameter model of cardiovascular system (CVS) was used for this evaluation. The results demonstrated that the designed controller was robustly tracking the input signal in the presence of the system parameter variations of CVS. In both scenarios, the proposed method shows that the controller automatically drive the LVAD with a minimum flow of 1.7 L/min to prevent suction and 5.7 L/min to prevent over-perfusion.

ABSTRACT: The idea of a Common Mucosal Immune system (CMS) is 50 years old. Its relevance to immune protection at mucosal sites and its potential to modulate the impact of vaccination-induced protection against infection of the airway, has been poorly understood. The consequent failure of current SARS-CoV-2 vaccination to satisfy expectations with respect to prevention of infection, viral transmission, duration of protection and pattern of clinical protection, led to public health and medical decisions now under review. This review summarises knowledge of the CMS in man, including the powerful role it plays in immune protection and lessons with respect to what can and can not be achieved by systemic and mucosal vaccination for prevention of airway infection. The powerful impact in both health and disease of optimising delivery of immune protection using selected isolates from the respiratory microbiome, is demonstrated through review of randomised controlled trials (RCT’s) in subjects with chronic airway disease, and in otherwise healthy individuals with risk factors, in whom the idea of mucosal immune resilience is introduced.

An efficient design method is proposed for a compact common-mode rejection (CMR) filter utilizing dumbbell-shaped defected ground (DS-DG) structures and gap-coupled stub (GCS) resonators. A CMR filter for differential lines helps to improve the signal integrity of high-speed digital signals on printed circuit boards. The proposed CMR filter design is based on the equivalent circuit models, while the previous designs depended heavily on the DS-DG structure optimization using the EM simulations. The proposed CMR filter effectively reject the common-mode components with minimally affecting the differential signals. To prove the simplified design approach, a 5th-order Chebyshev band-stop filter has been designed with three DS-DG structures and two GCS resonators. From the simulated and measured results, it is found that the proposed CMR filter provides ~90% fractional frequency bandwidth with more than 20 dB of common-mode rejection ratio and less than 0.6 dB of insertion loss of the differential signal.

The common dolphin is the second most bycaught species in Korean waters. To provide key information about their habitat boundaries and hotspots for spatial conservation and management, the spatial use of this species was examined using data obtained from sighting and bycatch surveys of cetacean during the past 20 years. The 95% minimum convex polygon and 95% density contour of fixed kernel suggested that the boundary of home range of common dolphins is limited to the coastal region (Busan-Sokcho) of the East Sea/Sea of Japan. From 50% density contours dawn by kernel density estimation, it was suggested that their hotspots are around the cost of Ulsan-Pohang, Doghae, and Sokcho within the home range. Common dolphins are not at all distributed in the Yellow Sea. Hence, shallow waters, such as the coastal region of the Yellow Sea, are not suitable habitats for common dolphins.

Worldwide, the cesarean section rate has steadily increased from 6.7% in 1990 to 21.1% in 2018 and is expected to rise even more. World Health Organization propose the adoption of the Robson classification system as a global standard for monitoring, evaluating, and comparing delivery rates. The purpose of the current study is to use the Robson classification system to investigate how, independently of medical factors, the day of the week and time of delivery may affect the mode of birth. In the sample analysis, we included the records of 8572 women giving birth in one private health facility in Greece. Over 60% of deliveries during the study period were performed by a cesarean section and 8.5% of deliveries were performed by operative vaginal delivery. The results of this study indicate that the lowest birth rates are observed on Monday, Saturday, and Sunday. In Robson category 1 women are 73% more likely to deliver by cesarean section between 08:00 a.m. - 03:59 p.m. compared to those who give birth between 12:00 a.m. - 07:59 a.m. Also, women in group 5.1 are 16.7 times more likely to deliver by cesarean section in the morning compared to overnight deliveries. These result point out two non-clinical variables that influences the CS rate. The Robson classification system was a useful tool for the above comparisons.

Loess is a special soil with high water sensitivity, which covers a large area in northwest China. Cracks are prone to generate in loess under the arid and semi-arid climate, which will provide the preferential channel for water and reduce the mechanical properties of soils. It is of great significance to understand the evolution characteristics and mechanisms of the cracks in loess areas. At present, the researches on cracks in soils are mainly concentrated in the characteristics of different cracking patterns. However, the spacing cracks are mostly discussed in materials like rock and concrete, rather than soils. The cracking characteristics and mechanisms of spacing cracks in loess is still inadequate. In this research, the drying tests of loess are carried out with different sizes of specimens. The parameters of spacing cracks and local strain distributions of the loess samples are obtained via PCAS and DIC methods during desiccation, respectively. The cracking modes, space cracking laws like insertion and saturation of spacing cracks are revealed. Finally, the size effect on the characteristics of spacing cracks is verified with a discrete element software MatDEM.

To predict the remaining useful life (RUL) of proton exchange membrane fuel cell (PEMFC) in advance, a prediction method based on the voltage recovery model and Bayesian optimization of a multi-kernel relevance vector machine (MK-RVM) is proposed in this paper. First, the empirical mode decomposition (EMD) method was used to preprocess the data, and then the MK-RVM was used to train the model. Then, the Bayesian optimization algorithm was used to optimize the weight coefficient of the kernel function to complete the parameter update of the prediction model, and the voltage recovery model was added to the prediction model to realize the rapid and accurate prediction of the RUL of PEMFC. Finally, the method proposed in this paper was applied to the open data set of PEMFC provided by FCLAB, and the prediction accuracy of the RUL of PEMFC was obtained by 95.35%, which showed that the method had good gen-eralization ability and verified the accuracy of the prediction for the RUL of PEMFC.

The security of several full homomorphic encryption (FHE) schemes depends on the hardness of the approximate common divisor (ACD) problem. The analysis of attack and defense against the system is one of the frontiers of cryptography research. In this paper, the performance of existing algorithms, including orthogonal lattice, simultaneous diophantine approximation, multivariate polynomial and sample pre-processing are reviewed and analyzed for solving the ACD problem. Orthogonal lattice (OL) algorithms are divided into two categories (OL-$\land$ and OL-$\vee$) for the first time. And an improved algorithm of OL-$\vee$ is presented to solve the GACD problem. This new algorithm works well in polynomial time if the parameter satisfies certain conditions. Compared with Ding and Tao's OL algorithm, the lattice reduction algorithm is used only once, and when the error vector $\mathbf{r}$ is recovered in Ding et al.'s OL algorithm, the possible difference between the restored and the true value of $p$ is given. It is helpful to expand the scope of OL attacks.

The aim of this study is to propose and validate the state space mode decomposition technique for precise mode separation of non-classical damping systems and closely distributed modal systems. To assess the reliability and applicability of this technique, a 40-story building with a tuned mass damper is investigated, and acceleration responses measured by the building's health monitoring system are used for the verification of the technique. The mode separation results reveal that the separated modal power spectrum becomes distorted at neighboring natural frequency ranges when the performance index only considers the concentration of power spectral energy at the target natural frequency. However, by introducing an augmented performance index that includes a constraint condition to account for distortion, more accurate mode decomposition can be achieved.

Hubei, Hunan and Henan Provinces are located in Central China, a region with extensive transport networks and trade. Bursaphelenchus xylophilus, the causative agent of pine wilt disease, is spreads mainly through human activities. In order to further understand the genetic structure of PWN in Central China, we studied the genetic information of PWN populations in this region and compared the genetic relationship with strains from Guangdong and Jiangsu provinces. We found that the HB (Hubei) 15, HEN (Henan) 20, HN (Hunan) 07, HN08 and HN10 had significantly more SNPs and homozygotes than other strains from Central China, and their most frequent mutant genotypes also differed from other strains. The clustering results indicated that HB15, HEN 20, HN07, HN08 and HN10 were genetically distinct from other strains and closely related to Guangdong strains. We also observed significant genetic variation among strains in Henan province, suggesting that some of them might have different transmission sources than those from Hubei and Hunan provinces. The results provide a basis for tracing the origin and spread of PWD in China.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

Due to nonlinear components in the charging piles of electric vehicles, harmonics and non-stationary signals in the electric vehicle charging load brings voltage and current distortion, seriously affecting the accuracy of the power-related calculation in non-sinusoidal environments. This paper proposed a new approach to calculate the active power and root mean square values from decomposed components using the adaptive chirp mode decomposition (ACMD) method on voltage and current. The advantage of the ACMD-based method is that it correctly provides the power-related quantities of harmonics or non-stationary components for the electric vehicle charging load. The performance of the proposed method was verified using synthetic signals and simulation tests. The experimental results presented better estimations for each quantity defined in IEEE Standard 1459-2010, compared with the discrete wavelet transform approach.

The human respiratory syncytial virus (hRSV) poses a serious risk to global public health and is a significant cause of severe lower respiratory infections. There are currently only a few therapies available to treat RSV infections, as well as no RSV vaccinations. Therefore, there is an urgent demand for clinically feasible, safe, and affordable RSV prevention and treatment alternatives. In this study, an ion-activated in situ gel comprising broad-spectrum antiviral 18β-glycyrrhetinic acid (GA) for antiviral action on RSV was developed. In this content, mechanical properties, sprayability, drug content, pH, ex vivo mucoadhesive strength, in vitro drug release pattern, and stability were all examined. Rheological properties were also tested by utilizing in vitro gelation capacity and rheological synergism tests. Finally, the optimized in situ gel's cytotoxic and antiviral activities on RSV cultured in human laryngeal epidermoid carcinoma (HEP-2) cell line were evaluated. In conclusion, the optimized in situ gel prepared with a combination of 0.5%w/w gellan gum and 0.5%w/w sodium carboxymethylcellulose demonstrated good gelation capacity and sprayability (weight deviation between T0 and T14: 0.34%), desired rheological synergism (mucoadhesive force (Fb): 9.53), mechanical characteristics (adhesiveness: 0.300 mJ ± 0.05), ex vivo bioadhesion force (19.67 g ± 1.90), drug content uniformity (RSD%: 0.494), and sustained drug release over period of 168 h (101.57% ± 0.53). The antiviral activity test results showed that the optimized in situ gel had strong anti-HRSV activity (EC50 simultaneous = 0.05 µg/ml, SI = 306; EC50 preinfection = 0.154 µg/ml, SI= 100) which was significantly higher than that of ribavirin (EC50 =4.189 µg/ml; SI= 28) used as a positive control against hRSV. In conclusion, this research has demonstrated the formulation of an effective antiviral nasal spray that has the ability to possess both prophylactic and virucidal activity.

The purpose of this paper is to study the influence of diffusion and thermal loading due to pulsed laser heating on a thermoelastic solid with voids in the context of the model of three-phase-lag. The non-dimensional governing equations are formulated and then the exact expressions for the temperature field, the displacement components, the stress components, the concentration field and the change in the volume fraction field are obtained using the normal mode technique. The material is an isotropic, homogeneous elastic half-space and heated by a non-Gaussian laser beam with pulse duration of ps. The magnesium crystal element is used as an application to compare the predictions induced by diffusion and laser pulse on poro-thermoelastic medium of the model of three-phase-lag with those for the theory of Green–Naghdi of type III. The results obtained for thermal changes are verified by comparison with two theories of thermoelasticity, namely the model of three-phase lag (3PHL) and the Green and Nagdi type III theory. Plot the expressions to examine the effect of the laser pulse at two different values of time and the effect void parameter. This study also yields some interesting special cases.

In this paper, we exhibit new dynamical properties of the two-mode Caudrey-Dodd-Gibbon (TMCDG) equation. This model describes the motion of dual-waves in dispersive and nonlinear media, which mainly depends on the nonlinearity and dispersion parameters. The overlapping of such two-mode waves is affected by the phase-velocity parameter. The study takes a full advantages of the Kudryashov method and of the exponential-expansion method. For the first time, dual-wave solutions are obtained for arbitrary values of the nonlinearity and dispersive factors. The graphs of the novel solutions are also provided in order to depict the waves propagation, as well as to show the influence of the parameters.

Biosensors detect specific bio-analytes by generating a measurable signal from the interaction between the sensing element and the target molecule. Surface acoustic wave (SAW) biosensors offer unique advantages due to their high sensitivity, real-time response capability, and label-free detection. The typical SAW modes are the Rayleigh mode and the shear-horizontal mode. Both present pros and cons for biosensing applications and generally need different substrates and device geometries to be efficiently generated. This study investigates and characterizes ultra-high-frequency (UHF-) SAW resonator biosensors. It reveals the simultaneous presence of the two typical SAW modes, clearly separated in frequency, called slow and fast. The two modes are studied by numerical simulations and biosensing experiments with the glial-fibrillary-acidic-protein (GFAP) biomarker. The slow mode is generally more sensitive to changes in surface properties, such as temperature and mass changes, by a factor of about 1.4 with respect to the fast mode.

Metal plasmonic nanostructures have promising applications in biosensing due to their ability to facilitate light-matter interaction. However, the damping of the metal leads to a wide full width at half maximum (FWHM) spectrum and results which restricts its sensing capabilities. In this research, we present a novel non-full-metal nanostructure, namely indium-tin oxide (ITO)-Au nanodisk arrays consisting of top ITO nanodisk arrays and a bottom gold layer, and compare the coupling mode with the full-metal nanodisk arrays. The FWHM of proposed ITO-Au nanodisk array reduces to one fifth of that all metal nanodisk arrays, which is generated mode-coupling by surface plasmon modes at metal interfaces with magnetic resonance mode. Furthermore, the thickness variation of nanodisks has no impact on the sensing performance of this ITO-based nanostructure, ensuring excellent tolerance during preparation. We fabricated both structures by using template transfer and vacuum deposition techniques and calibrated their sensing performances by detect Immunoglobulin G (IgG) protein molecules. Both theoretical and experimental results demonstrate that ITO-Au nanodisk arrays provide an effective solution for biosensing applications.

Recently, various research has been developed addressing communication sensors for Unmanned Aerial Systems (UASs); especially when pondering control difficulties, communication is a crucial component. To this end, strengthening a control algorithm with redundant linking sensors ensures the overall system works accurately even if some components fail. This paper proposes a novel approach to integrate several sensors and actuators for a heavy Unmanned Aerial Vehicle (UAV). Additionally, a cutting-edge Robust Thrust Vectoring Control (RTVC) technique is designed to control various communicative modules during a flying mission and converge the attitude system to stability. The results of the study demonstrate that even though RTVC is not frequently utilized, it works as well as cascade PID controllers, particularly for multi-rotors with mounted flaps, and could be perfectly functional in UAVs powered by thermal engines to increase the autonomy since the propellers cannot be used as controller surfaces.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

Considering rotation-induced centrifugal stiffening, spin softening, and Coriolis effects, the three-dimensional finite element model of a rotating blade with a dovetail structure is built through the contact dynamics theory. The fixed-interface component mode synthesis method is then adopted to reduce the model for high computational efficiency and adequate model accuracy. The effects of the number of normal modes on the first-six-order modal characteristics of the model varying with the rotating speed are studied between the reduced and full models. Next, the influence of rotating speed and friction factor on the nonlinear dynamic characteristics of the model under the action of aerodynamic force are elaborately discussed. The results show that: (1) tenon-mortise joint contact-induced nonlinearity under low rotating speeds results in the intermittent interference of contact surfaces and frequency multiplications of aerodynamic excitation frequency in the spectrum cascades, while that under high rotating speeds causes the continuous interface contact and asynchronous excitation at the tenon-mortise joint; (2) the increase of friction factor results in a lower contact pressure distribution and the right shift of the resonance peak (i.e., hard nonlinearity).

According to the structural features, sedimentary evolution, types of sedimentary facies, source rocks features, diagenesis evolution, reservoir features and hydrocarbon formation mechanism, exploration status and hydrocargon resource potential, this article analyzed the major control fac-tors and hydrocarbon distribution rules of the lithologic reservoirs in continental fault basin. The research shows that three major control factors and one coupled factor (fractures act as a tie) in-fluence hydrocarbon formation of lithologic traps in Nantun Formation of Tanan Sag, which in-clude sand body types, effective source rocks and effective reservoirs. With the increase in depth, enough hydrocarbon generate in source rock under thermal evolution. Hydrocarbon generation and expulsion are more intensive when it comes to the depth threshold and critical conditions of hydrocarbon supplying are met. Traps that surrounded or contacted by source rock, or communi-cated by fault are qualified to form reservoirs. As buried depth increases, hydrocarbon genera-tion-expulsion intensity grows and the trap is more petroliferous. Hydrocarbon accumulation and reservoir formation are also controlled by sandbody accumulation conditions. When it meets the critical conditions of hydrocarbon generation and concrete oil and gas are charged in, better phys-ical properties of sandbody always indicate more hydrocarbon accumulation in the trap. Alloca-tion of sand type, effective source rock and effective reservoir is optimized under the effect of fractures, and coupled hydrocarbon reservoir with these three elements.

Photovoltaic(PV) power generation is highly nonlinear and stochastic. Accurate prediction of PV power generation plays a crucial role in grid connection as well as the operation and scheduling of power plants. To predict the PV power combination model, this paper suggests a method based on Empirical Mode Decomposition (EMD), Ensemble Empirical Mode Decomposition (EEMD), Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN), Nonlinear Auto-Regressive Neural Networks with Exogenous Input (NARXNN), Long Short Term Memory (LSTM) Neural Network, and Light Gradient Boosting Machine (LightGBM) algorithms. To attempt to reduce the non-smoothness of PV power, the weather variable features with the greatest effect on PV power are first identified by correlation analysis. Following this, the PV power modal decomposition is split and reorganized into a new feature matrix. Finally， a NARX is used to obtain preliminary PV power components and residual vector features， and the PV power is predicted by combining three models of LightGBM， LSTM, and NARX and then the final prediction results are obtained by combining the PV power prediction results using error inverse method weighted optimization. The prediction results demonstrate that the model put forth in this paper outperforms those of other models and validate the model's validity by utilizing real measurement data from Andre Agassi College in the United States.

The use of fiber optics as a tool for different kinds of geotechnical monitoring can become highly attractive and cost effective when compared to conventional instruments such as piezometers, inclinometers, among others. A single fiber optic cable may cover a larger monitoring area compared to conventional instrumentation, and the possibility of monitoring more than one physical quantity with the same fiber optic cable. Consulting the literature, it is possible to find several different examples where distributed fiber optic systems are being used. For the use of any sensor, a calibration curve is required. In the case of strain sensors, calibration is required to derive strain values from the frequency measurement quantity. However, fiber optic sensor cable manufacturers often do not provide their own calibration parameters and consult the values in specialized literature, which can result in monitoring errors. In this context, this article presents a bench adjusted for tests on single mode fiber optic cables, as well as results of tensile tests aimed at defining the function of strain variations of two different optical fiber cables, manufactured by different companies, using two different distributed interrogators. This paper also proposes a methodology for calibrating of the fiber optic cables deformation since the calibration parameters are provided by the cable manufacturers, which can result in errors depending on the application. It should be noted that there are few manufacturers of fiber optic cables aimed at application in civil engineering. Therefore, with the calibration methodology proposed in this paper, it is intended to transmit to the academic community the possibility of obtaining calibration parameters of any fiber optic cable, even those manufactured for telecommunications purposes and not only for cables manufactured with the intended use in civil engineering. Because of this fact, researchers will not be restricted to the acquisition of special cables for their applications. Based on the results, it was possible to conclude that the application of calibrated fiber optic sensors in experimental piles foundations is viable, in order to evaluate the load-displacement behavior of these elements, under different loading conditions.

This paper attempts to develop a Dynamic Mode Decomposition (DMD) based Reduced Order Model (ROMs) which can quickly but accurately predict the forces and moments experienced by a road vehicle such that they be used by an on-board controller to determine the vehicle's trajectory. DMD can linearize a large dataset of high-dimensional measurements by decomposing them into low-dimensional coherent structures and associated time-dynamics. This ROM then also can be applied to predict the future state of the fluid flow. Existing literature on DMD is limited to low Reynolds number applications. This paper presents DMD analyses of the flow around an idealized road vehicle, called the Ahmed body, at a Reynolds number of 2.7E6. The high dimensional dataset used in this paper was collected from a computational fluid dynamics (CFD) simulation performed using Menter's shear stress transport (SST) turbulence model within the context of Improved Delayed Detached Eddy Simulations (IDDES). The DMD algorithm, as available in literature, was found to suffer nonphysical dampening of the medium-to-high frequency modes. Enhancements to the existing algorithm were explored, and a modified DMD approach is presented in this paper which includes: (a) a requirement of higher sampling rate to obtain higher resolution of data, and (b) a custom filtration process to remove spurious modes. The modified DMD algorithm thus developed was applied to the high Reynolds number, separation dominated flow past the idealized ground vehicle. The effectiveness of the modified algorithm was tested by comparing future predictions of force and moment coefficients as predicted by the DMD-based ROM to the reference CFD simulation data, and found to offer significant improvement.

Building on the study by Abdullah et al. (2020), this study aims to analyze the perception of travel, especially in this context of the pandemic, when the measures are alleviated, as well as the citizens' intention and preferences for travel methods during the COVID-19 pandemic. The purpose of the study is to investigate the impact of the COVID-19 pandemic on travel behavior and travel mode preferences in the example of the residents of Bosnia and Herzegovina. Five research questions were defined. A quantitative research approach was applied in this study. The data was collected through a questionnaire (online survey) distributed to respondents via e-mail and the social network Facebook. The convenience sample included 265 respondents. Descriptive analysis, as well as quantitative comparative analysis, were carried out on the collected data. The results show that the COVID-19 pandemic has influenced a change in travel behavior. The primary purpose of travel before and during the COVID-19 pandemic was social activities. The most significant change in the primary purpose of travel before and during the COVID-19 pandemic is reflected in a decrease in social activities and an increase in recreational sports activities. In contrast, other activities remained proportionally the same before and during the COVID-19 pandemic. The average distance traveled for primary outdoor trips before the COVID-19 pandemic is greater than that for primary outdoor trips during the COVID-19 pandemic. This article allows for better organization and planning for the future in the event of another pandemic.

Whole genome duplication (WGD) or polyploidization can occur at the cellular, tissue, and organismal levels. At the cellular level, tetraploidization has been proposed as a driver of aneuploidy and genome instability, and correlates strongly with cancer progression, metastasis, and development of drugs resistance[1–6]. WGD is also a key developmental strategy for regulating cell size, metabolism, and cellular function[1,7–10]. In specific tissues, WGD is involved in normal development (e.g. organogenesis), tissue homeostasis, wound healing, and regeneration[10–17]. At the organismal level, WGD propels evolutionary processes such as adaptation[18], speciation[19], and crop domestication[20]. An essential strategy to further our understanding of the mechanisms promoting WGD and its effects is to compare isogenic strains that differ only in their ploidy. Caenorhabditis elegans (C. elegans) is emerging as an animal model for these comparisons, in part because relatively stable and fertile tetraploid strains can be produced rapidly from nearly any diploid strain[7]. Here we review the use of Caenorhabditis polyploids as tools to understand important developmental processes (e.g. sex determination, dosage compensation, and allometric relationships)[21–27] and cellular processes (e.g. cell cycle regulation, chromosome dynamics during meiosis)[28–32]. We also discuss how the unique characteristics of the C. elegans WGD model will enable significant advances in our understanding of mechanisms of polyploidization and its role in development and disease.

In an $m$-person symmetric game, all players are identical and indistinguishable. In this paper, we find that the payoff tensor of the player $k$ in an $m$-person symmetric game is $k$-mode symmetric, and the payoff tensors of two different individuals are the transpose of each other. Furthermore, we reformulate the $m$-person symmetric game as a tensor complementary problem and demonstrate that locating a symmetric Nash equilibrium is equivalent to finding a solution to the resulting tensor complementary problem. Finally, we use the hyperplane projection algorithm to solve the resulting tensor complementary problem, and we present some numerical results to find the symmetric Nash equilibrium.

As one of the fastest-growing new energy sources, wind power technology has attracted widespread attention from all over the world. In order to improve the quality of wind power generation, wind speed prediction is an indispensable task. In this paper, an error correction based Variational Mode Decomposition and Broad Learning System (VMD-BLS) hybrid model is proposed for wind speed prediction. First, the wind speed is decomposed into multiple components by the VMD algorithm, and then an ARMA model is established for each component to find the optimal number of sequence divisions. Second, the BLS model is used to predict each component, and the prediction results are summed to obtain the wind speed forecast value. However, in some traditional methods, there is always time lag, which will reduce the forecast accuracy. To deal with this, a novel error correction technique is developed by utilizing BLS. Through verification experiment with actual data, it proves that the proposed method can reduce the phenomenon of prediction lag, and can achieve higher prediction accuracy than traditional approaches, which shows our method’s effectiveness in practice.

One of the stated goals of the Common Agricultural Policy reforms has been to provide a fairer distribution of payments across and within Member States, but little progress has been accomplished, with about 20% of farmers receiving 80% of the total amount of Direct Payments. The structural factors that underlie this inequity, notably the preponderance of specific types of farming systems, are investigated in this research. A logit model was developed using Agricultural Census data at the Commune level, using the evolution of the percentage of farmers receiving Direct Payments in Portugal as the dependent variable. The findings reveal that the local importance of arable crops (cereals) and cattle farming systems, as well as the existence of larger farms and younger farmers, all contributed to farmers' increasing access to DP between 2009 and 2019. In traditional Mediterranean farming systems, however, access to DP has been restricted to a smaller proportion of farmers. However, there appears to have been some redistribution in the previous two CAP programming cycles, from bigger to smaller farmers, older to younger farmers, and from olives, cereals, and cattle to other types of production, notably vineyards.

The discovered light modulation capabilities of diatom silicious valves make them an excellent toolkit for photonic devices and applications. In this work, a reproducible surface-enhanced Raman-scattering (SERS) enhancement was achieved with hybrid substrates employing diatom silica valves coated with an ultrathin uniform gold film. Three structurally different hybrid substrates, based on the valves of three dissimilar diatom species, have been compared to elucidate the structural contribution to SERS enhancement. The comparative analysis of obtained results showed that substrates containing cylindrical Aulacoseira sp. valves achieved the highest enhancement up to 14-fold. Numerical analysis based on the frequency domain finite element method was carried out to supplement the experimental results. Our results demonstrate that diatom valves of different shapes can enhance the SERS signal, offering a toolbox for SERS-based sensors, where the magnitude of the enhancement depends on valve geometry and ultrastructure.

This study presents a dynamic model of a passenger vehicle and analyzes its dynamic characteristics and responses. A dynamic vehicle model with seven degrees of freedom was established to analyze the behavior of a driving vehicle. The vehicle model had three degrees of freedom for the motion of the sprung mass and four degrees of freedom for the unsprung masses. For this model, the equations of motion were derived using Lagrange’s equation. To verify the model, the suspension deformations computed using the model were compared with the deformations measured through three actual vehicle driving tests which are the slalom, double lane change, and step steer tests. Furthermore, we investigated the effects of suspension stiffness, suspension damping, and anti-roll bar torsional stiffness on the dynamic characteristics and responses of the vehicle model. The developed dynamic vehicle model may help vehicle designers predict the dynamic responses of a vehicle through simulation without performing a driving test.

Optical switching is an essential part of photonic integrated circuits and the focus of research at the moment. In this research, an optical switch design working on the phenomenon of the guided-mode resonances in 3D photonic crystals-based structure is reported. The optical-switching mechanism is studied in a dielectric slab-waveguide-based structure operating in the near-infrared range in a telecom window of 1.55 µm. The mechanism is investigated by interference of two signals, i.e., the data signal and the control signal. The data signal is coupled into the optical structure and filtered utilizing guided-mode resonance, whereas, the control signal is index guided in the optical structure. The amplification or de-amplification of the data signal is controlled by tuning the spectral properties of the optical sources and structural parameters of the device. The parameters are optimized first using a single-cell model with periodic boundary conditions and later in a finite 3D-FDTD model of the device. The numerical design is computed in an open-source Finite Difference Time Domain simulation platform. Optical amplification in the range of 13.75 % is achieved in the data signal with a decrease in the linewidth up to 0.0079 µm and a quality factor of 114.58. The proposed device presents great potential in the field of photonic integrated circuits, biomedical technology, and programmable photonics.

Variable-DOF (or kinematotropic) mechanisms are a class of reconfigurable mechanisms. The number of variable-DOF multi-loop planar mechanisms proposed so far is very limited. This paper proposes a novel 8-link variable-DOF planar mechanism with five motion modes. Firstly, a description of the 8-link variable-DOF planar mechanism is presented. Reconfiguration analysis of the 8-link mechanism is then carried out using an elimination and algebraic geometry hybrid approach. The analysis shows that the 8-link mechanism has one 2-DOF motion mode and four 1-DOF motion modes and can switch among three motion modes at four transition configurations and between two motion modes at the remaining four transition configurations. Geometric characteristics of the mechanism in different motion modes are also revealed. Unlike the variable-DOF planar mechanisms found in literature, the proposed 8-link mechanism has two inactive joints in one of its 1-DOF motion modes, and both 4R kinematic sub-chains of the mechanism must appear as parallelograms in a pair or anti-parallelograms in a pair in the same motion mode. As a by-product, a method for factoring trigonometric functions in two angles is proposed.

Background: Malaria remains a serious public health concern worldwide, particularly in tropical and subtropical regions, and the leading causes of mortality and morbidity in children especially among those aged under five in developing countries. Malaria can be fatal if not promptly and accurately diagnosed, especially in children.This study was carried out to determine the level of malaria infection and its associated risk factors among febrile children.Methods: Blood samples were collected and analyzed from two- hundred (200) systematically selected febrile children aged 1-10 years old. assay of samples collected were carried out using standard methods.data were collected using a pretested structured questionnaire. Results: Results obtained from study subjects shows that, of the eighty-seven (87) infected subjects, 34 (39.1%) were aged 1-5 years, while 52 (59.8%) were within the range of 6 years and above.severity of infection showed 48 (55.2%) with scanty parasitic infection while 25 (28.7%) showed moderate infection, and 13 (14.9%) showed heavy infection.The association of age and level of parasitemia showed that 34 (58.8% ) subjects below 5 years, recorded scanty malaria compared to 14.7% with severe malaria within the age range.Considering gender, of the 33 infected female subjects, 45.5% had scanty malaria, 36.4% showed moderate malaria, while 18.2% had severe malaria, compared to the males subjects.Conclusion: This study reveals the prevalence of malaria infection with some level of severity among children at our study location.The need for prompt diagnosis and improved access to all malaria interventions becomes relevant,with a special focus on the high risk group.

Hydro generator sets serve as the peak and frequency regulation of the power system,and play a very important role in maintaining system stability and improving power quality.Based on the internal characteristics model of a specific type of hydro generator,this paper constructs a hydroelectric coupling model for hydropower units,studies the influence of the regulation system of hydropower units on low-frequency oscillations under different load conditions,and adopts variable speed reaching law and fuzzy sliding mode control strategy to improve the regulation quality of the system and ensure the stable operation of the units.Results of simulation and water turbine set under different load conditions show that varible speed reaching law can effectively improve the power-angle oscillation behavior of the hydropower set and suppress the occurrence of low-frequency oscillations of the system when the system is subject to power disturbance,which provide a new theoretical basis and solution for the vibration analysis and control optimization of hydraulic turbine units.

Technology-enabled maintenance via sensors and the internet of things (IoT) technologies is seen as the “new maintenance strategy”. The aim is to use these technologies to focus on unnecessary breakdowns and increase levels of asset availability where the existing of a dedicated team to maintain or data on asset condition is limited, useless or full of noise. This paper presents the integration of various sensing nodes within an automated laser cutting machine for monitoring of critical components’ conditions. The integrated system provides a centralised platform for data collection from various sensors and provides early failure detection mechanism based on specified set points with alert mechanisms utilising a custom dashboard for data visualisation. The research highlights the required stages for the identification of the appropriate components and sensory devices for the development of efficient monitoring environment.

Different values of the Hubble constant for extragalactic objects are not considered here. We give a number of examples of the extreme accordance of expansion rates of different fields of knowledge with the cosmological expansion rate. The coincidence of the expansion rates means that a common cause is almost inevitable. All these examples are gravitationally bound in themselves and in this case are subject to cosmological expansion. According to standard theory, this should not happen. We therefore question the common boundary of gravity and expansion for both theoretical and observational reasons and conclude that all gravitationally dominated objects participate in cosmological expansion or scale drift, contrary to general doctrine. The space expands with its contents while numerically maintaining distance, radius, rotation time and density. What is generally interpreted as an expansion is obviously a scale drift with a drift rate that corresponds to the size of the Hubble constant. The Earth is subject to expansion and scale drift. This results in numerically constant measured values. This drift apparently also applies to distant galaxies and other objects. The cosmological red shift is not interpreted here as a Doppler effect and numerical increase in distances, but in accordance with standard theory as an expansion or drift of the space-time scale. The expansion of the radii of galaxies makes the assumption of dark matter superfluous. The continents and our everyday environment are not subject to expansion or scale drift.

The results of physico-chemical studies of individual fruit parts, including crusts, partitions, juice and seeds themselves, extracted from immature (green), unripe and mature fruits of three harvest periods are presented: 20.VII, 01.IX and 15.X. The analyses were carried out in 2019-20 during the period of active growth and ripening of fruits in the varieties Spring, Iridanaly, Guleisha pink and wild pomegranate from the Geokchay region (Azerbaijan) using standard and generally accepted physico-chemical methods. The ripe fruit (130-288 g) consisted of 60-113% of the peel (peel together with partitions), 53-140% of the juice and 17-85% of the seeds themselves. The edible part of the ripened fruits (53.85-73.2 of the total weight of the fruit) consisted of 58.54-78.65% juice and 21.35 -41.46% seeds, fresh juice contained 15.7-17.7% solids, including 12.04-13.84% sugar, 0.17-0.30% protein, 0.15—0.23% pectin, 0.30-0.40% ash and 0.26-0.57% total polyphenols. The concentrations of solids, protein, ash and total polyphenols in the seeds themselves, remaining after the extraction of juice from the grains of ripe fruits, were 50.0-58.2, 4.13-5.75, 0.60-1.0 and 0.08-0.32%, respectively. There were fewer total polyphenols, flavonoids, chlorogenic acids, catechins and leucoanthocyanins in ripe fruits, and more ascorbic acid, anthocyanins and proanthocyanidins than in unripe ones. The period from the second half of July to the beginning of September is the time of a real “boom” of common polyphenols.

Newton’s law of universal gravitation applies between two point-masses. True gravitation of solid Earth is volume integration of gravitation of all point-masses inside the solid Earth on a point-mass in atmosphere. However, in meteorology the Earth “shrinks” into a point-mass located at Earth center with entire Earth mass to identify the Earth gravitation (untrue). Combination of untrue gravitational and centrifugal accelerations gives effective gravity (geff). Combination of true gravitational and centrifugal accelerations leads to true gravity (g). The true gravity g minus the effective gravity geff is the gravity disturbance vector, δg = g – geff. With the true gravity g used in the basic equations, seven non-dimensional numbers are proposed to identify the importance of δg versus traditional forcing terms such as horizontal pressure gradient force and Coriolis force. These non-dimensional numbers are calculated from two publicly available datasets with the geoid undulation (N) from the static gravity field model EIGEN-6C4 and long-term mean geopotential height (Z), wind velocity (u, v), and temperature (Ta) at 12 pressure levels in troposphere from the NCEP/NCAR reanalyzed climatology. The results demonstrate δg nonnegligible in hydrostatic equilibrium, geostrophic wind, geostrophic vorticity, Ekman pumping, Q vector, and Omega equation, but negligible in thermal wind relation.

This article is some review of results that were obtained at 2007-2021 years development of “The Information as Absolute” concept and the informational physical model, which is based on the concept; including a number of fundamental physical problems are briefly considered in framework of the conception and the model. Recently in physics there are several publications, that present lists of the problems. However, those lists are essentially incomplete, for at least two reasons. Firsts of all, a number of phenomena are studied traditionally by philosophy, and so corresponding problems are usually considered to be “metaphysical”. However, they relate also to some concrete physical phenomena. For example, physics evidently studies Matter, and so the metaphysical problems “what is ontology of Matter”, “what is “Space”, “Time” and a few other physical phenomena and notions as well, are really a Meta-physical problems “what does physics study?” There are other fundamental physical problems, which are not considered as such in physics, and are absent in the “fundamental problems lists”. Those include the problems, which really exist, yet are incorporated into standard physical theories, and so are fundamental “implicitly”, which in physics are “solved by default” ‒ and mostly erroneously. Note, though, that a number of “Meta-physical”, and concrete fundamental, problems more in detail are considered in the paper “The Informational Conception and Basic Physics”, https://arxiv.org/abs/0707.4657, v5 (2021), so this paper is, in certain sense, an expanded conclusion of this paper, which includes, correspondingly, more in detail consideration of some more general physical problems; and, besides, in this article, the problem “what are Gravity and Electric Forces” is essentially clarified comparing with the arXiv 2021 paper version above. Besides, the concrete problem “What is Life”, and the rational cosmological model, where a few vague points in standard cosmology rather probably are rationally clarified, while the fundamental problem “matter – antimatter asymmetry” in Matter is solved practically for sure, are considered, and one of recently published rather complete “lists of fundamental problems” is commented in Appendix.

Common root rot caused by Bipolaris sorokiniana infestation of wheat is one of the main reasons of yield reduction in wheat crops worldwide. In current study, strain JK-25 was isolated from soil of wheat rhizosphere and identified as Bacillus halotolerans based on morphological, physiological, biochemical characteristics and molecular identification. The strain showed significant antagonism to B.sorokiniana and broad-spectrum resistance to Fusarium oxysporum, Fusarium graminearum and Rhizoctonia zeae. Inhibition of Bipolaris sorokiniana mycelial dry weight and spore germination rate by JK-25 fermentation supernatant reached 60% and 88% respectively. The crude extract of JK-25 was found by MALDI-TOF-MS to contain the surfactin that exerted an inhibitory effect on B.sorokiniana. The disruption of mycelial cell membranes was observed under microscopy (LSCM) after treatment of B.sorokiniana mycelium with the crude extract. The antioxidant enzyme activity of B.sorokiniana was significantly reduced and the oxidation product MDA content increased after treatment with the crude extract. The incidence of root rot was significantly reduced in pot experiments with the addition of JK-25 culture ferment, which had a significant biological control effect of 72.06%. Its ability to produce siderophores may help to promote wheat growth, and the production of proteases and pectinases may also be part of the strain's role in suppressing pathogens. These results demonstrate the excellent antagonistic effect of JK-25 against B.sorokiniana and suggest that this strain has great potential as a resource for biological control of wheat root rot strains.

Object of this work is the design and the simulation of a hybrid UAV with VTOL capabilities that has been designed for landing on naval moving platforms. The work is focused on the innovative propulsion layout adopted on the UAV. Authors discuss how adopted low level control strategies can exploit the innovative features of the proposed system assuring a good rejection of transversal wind disturbances. Particular attention is dedicated to low level modelling and control of the system emphasizing how choices regarding low level actuation and control should improve performances and robustness of the system.

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

Abstract: Background: COVID-19 is a respiratory disease that eventually became pandemic with 300 million people infected around the world. Alongside the improvement in COVID-19 management and vaccine development, identifying biomarkers for COVID-19 has recently reported to help in early prediction and managing severe cases which might improve outcome. The Aim of our study was to find out if there is any correlation between clinical severity and elevated hematological and biochemical markers in Covid-19 patients and its effect on the outcome Methods: We have collected data retrospectively of socio-demographic, medical history, biomarkers, and diseases outcome from five hospitals and health institutions in the Kingdom of Saudi Arabia. Results: Pneumonia was the most common presentation of COVID 19 in our cohort. All biomarkers (D-Dimer, CRP, troponin, LDH and ferritin) except for the mean lowest white blood cells were found to have significant correlation (p<0.05) with worse COVID-19 disease outcomes. There was a sig-nificant association between the inflammatory biomarkers and the disease severity of COVID 19 patients (p<0.001). Patients with evidence of severe respiratory disease particularly who required mechanical ventilation (MV) had higher biomarkers, when compared to those with stable respiratory condition (p<0.001). Conclusion: Identifying biomarkers predicts outcome for COVID-19 patients and may significantly help in the management.

During the past few years unexpected developments have driven studies in the field of clinical immunology. One driver of immense impact was the outbreak of a pandemic caused by the novel virus SARS-CoV-2. Excellent recent reviews address diverse aspects of immunological re-search into cardiovascular diseases. Here, we specifically focus on selected studies taking ad-vantage of advanced state-of-the-art molecular genetic methods ranging from genome-wide epi/transcriptome mapping and variant scanning to optogenetics and chemogenetics. First, we discuss emerging clinical relevance of advanced diagnostics for cardiovascular diseases - includ-ing those associated with COVID-19 - with a focus on the role of inflammation in cardiomyopa-thies and arrhythmias. Second, we consider newly identified immunological interactions at or-gan and systems level which affect cardiovascular pathogenesis. Thus, studies into immune in-fluences arising from the intestinal system are moving towards therapeutic exploitation. Fur-ther, powerful new research tools have enabled novel insight into brain – immune system inter-actions at unprecedented resolution. This latter line of investigation emphasizes the strength of influence of emotional stress - acting through defined brain regions - upon viral and cardiovas-cular disorders. Several challenges need to be overcome before the full impact of these far-reaching new findings will hit the clinical arena.

Nowadays brushless DC motors (BLDCMs) are becoming indispensable components as the electrification revolution in the mobility industry is happening. Electric kick scooters, so-called e-scooters, are among these micro-mobility vehicles which are powered by these motors. Due to the uncertain and nonlinear features, the controller performance developed for these motors degrades. For these reasons, a chattering-reduced cascaded Sliding Mode Control (SMC) scheme to effectively track reference motor speed in the outer loop by eliminating torque ripples in the inner loop current control was designed. Field-oriented Control (FOC) methodology was used to implement the SMC in the BLDCM. An exponential reaching law algorithm was proposed for sliding surfaces of the inner and outer loop controllers. The suitability and performance of electric scooter-hub motors were analyzed in terms of traction control. A cascaded speed and torque controller produced significantly favorable results representing minimized torque and current ripples, and operation over a wide speed range.

Voltage Source Inverters (VSI) are the integral part of Electrical Vehicles (EV) to enhance the reliability of supply power to critical loads in vehicle to load (V2L) applications. Inherent properties of sliding mode control (SMC) makes it one of the best vailable options to achieve desired voltage quality under variable load conditions. Intrinsic characteristic of robustness associated with SMC is achieved generally at the cost of unwanted chattering along the sliding surface. To manage this compromise better, optimal selection of sliding surface coefficient is applied with proposed composite exponential reaching law (C-ERL). The novelty of proposed C-ERL is associated with the intelligent mix of exponential, power and difference functions blended with rotating sliding surface selection (RSS) technique for three phase two level VSI. Moreover, proposed reaching law along with power rate exponential reaching law(PRERL), enhanced exponential reaching law(EERL) and repeatitive reaching law(RRL) are implemented on two level three phase VSI under variable load condtions. Comparative analysis of which strongly advocates the authenticity and effectiveness of proposed reaching law in achieving well regulated output voltage, with high level of robustness, reduced chattering and low %THD.

The condition of surface transportation infrastructure directly affects the economic health of a nation. However, it is difficult to justify the large sums of money needed to extend current methods to monitor all the multimodal infrastructure. The convergence of connected vehicle and cloud computing technologies presents an opportunity to automate the collection of ride quality and imagery data to continuously assess the condition of all roadways and railways. This paper presents several perspectives to help policy and standardization initiatives promote adoption.

Hydraulic fracturing for oil-gas and geothermal reservoir stimulation is closely related to the generation and propagation of Mode I crack. Nonlinear deformation due to rock heterogeneity occurs at such crack tip, which causes the fracture process zone (FPZ) to form before the crack propagates unsteadily. However, the relationship between the FPZ characteristics and rock heterogeneity still remain elusive. We used three rock types common in reservoir for experimental investigation, and each of them includes two subtypes with different heterogeneity due to grain size or microstructural characteristics. Drawing on the experiment results, we calculated the FPZ size in each cracked chevron notched Brazilian disk, and we reproduced the formation process of the FPZ in marble by discrete element method. We showed that strong heterogeneity is favorable to large FPZ size, can enhance the ability of crack generation and complicate crack morphology. Coupling the Weibull distribution with fracture mechanics, the dependence of the FPZ size on heterogeneity degree can be theoretically explained, which suggests that inherent heterogeneity of rocks set physical foundation for formation of FPZ. These findings can improve our recognition to formation mechanism of the Mode I crack and provide useful guidelines for evaluating reservoir fracability.

Data on helminth parasites and epizoites is presented for the long-beaked and short-beaked common dolphins from the Southeast Pacific. Sampling in 1985-2000 was conducted mainly at six fishing ports in Peru and Ecuador where cetaceans were landed. From a total of 473 common dolphins sampled, we identified helminths including three species of Trematoda: Nasitrema globicephalae, Pholeter gastrophilus and Braunina cordiformis; three species of Nematoda, which includes Anisakis spp., Crassicauda sp. and Halocercus sp.; and two cestodes Tetrabothrius forsteri and Clistobothrium delphini (formerly Phyllobothrium delphini). No acanthocephalans were observed. No statistically significant sexual and ontogenetic variation in helminth prevalence was detected after which samples were pooled. The highest prevalence in the long-beaked common dolphin (n=440) was observed for N. globicephalae (96.3%) in cranial sinuses, Crassicauda sp. (83.3%) in mammary glands, Crassicauda sp. (78.8%) infesting the cranial sinuses, followed by Cl. delphini (28.6%) in the blubber and P. gastrophilus and B. cordiformis (20.4%) in the digestive tract. Although comparative testing was unfeasible due to minimal samples of short-beaked common dolphin (n=33), several of the same helminth species were found, but not N. globicephalae nor B. cordiformis. No cyamids were encountered while pseudo-stalked barnacles Xenobalanus globicipitis were common. No new (global) helminth host records are revealed for common dolphins, but this study presents a first checklist of parasites separately for the Southeast Pacific long-beaked and short-beaked common dolphins. Future work should include exhaustive laboratory-based necropsies, enhanced sampling of the short-beaked form, focus on intermediate hosts and parasitic pathology, including potential human health impact from consumption of small cetaceans.

Wildlife conservation is an important component of environmental sustainability and can be improved by reviewing the performance of its three major models – common pool, top-down regulatory, and private resource -- under varying environmental and socioeconomic conditions. Generally, the private resource model is the most sustainable because it provides the best incentives to balance the needs of humans and wildlife, to maintain general wildlife habitat, and to adapt quickly to changing environmental and/or socioeconomic conditions. Top-down or “command and control” regulation, however, can be employed as a model of last resort if the private resource model shows signs of failing to protect specific species from local extirpation or extinction, which it is most likely to do for migratory species, species with close commercial substitutes, and species with no direct commercial value. Top-down regulators may also be needed to enforce property rights arrangements like catch shares and to monitor resources that remain in the common pool in the event that socioeconomic or environmental conditions change sufficiently to trigger the tragedy of the commons.

Smartphone-based mobility apps enable users to make informed transportation decisions, offering instant access to transport-related information. This development has created a smartphone-enabled ecosystem of mobility services in developed countries while it is slowly picking up pace in the global south, which can contribute towards the decarbonization of urban transport. Work on this has already started in India, and there is considerable evidence indicating the profound impact of these apps on the perceived utility and usage of transport modes, with far-reaching implications for sustainable development goals (SDGs). However, for most users, the use of smartphone apps is a novel trend, and the knowledge of the impacts of usage of existing apps on the usage pattern of transport modes by various user groups is essential for positioning new consolidated app-based services soon. Against this backdrop, the present study uses latent class cluster analysis to empirically investigate the impacts of mobility apps on transport mode usage patterns in Delhi by classifying users into latent classes based on socioeconomic characteristics, attitudes/preferences, smartphone app usage, and mode usage pattern. The characteristics of the latent class and factors affecting the individual’s probability of being classified to these cluster have been discussed, along with some measures to encourage app-based mobility for each cluster.

With growing city tourism, there is an increasing need for urban travel demand models to consider traffic generated by visitors. Existing research has concentrated on socio-demographic and journey-related factors to determine what influences the mode choice of tourists. In contrast, revealed preference data, like travel time, is almost never considered. In this article, we present the results of discrete choice modeling of city tourists’ mode choice based on revealed preference data from a survey we conducted in Kassel, Germany. We used multinomial logit models and determined the model parameters using maximum likelihood estimations. Surprisingly, travel time played a smaller role in mode choice than understood from previously established knowledge about everyday mobility. In the final model, travel time was only significant for the alternative walking. Also, most other sociodemographic and journey-related variables showed no significant influence. The final model reproduced the mode choice, but the goodness of fit was lower than expected from other research. We conclude that modeling the travel behavior of tourists is more complex than everyday mobility. An alternative approach that we suggest would be to model trip chains rather than single trips.

Running at odds with the timing imposed by the circadian clock plays an important role in the process that leads to communicable and non communicable diseases. The primary objective of this study was to analyse whether early dinner eater children were at lower risks of acute respiratory infections than late dinner eater children, during the COVID-19 pandemic. Methods: This cross sectional study was conducted from July to December 2020 on children attending Majorcan emergency services. Clinical data collected included timing, symptoms, laboratory tests and imaging studies of current illness. Each diagnosis was validated by general paediatricians. Our survey on dinner time habits was carried out by using self-administered questionnaires. Results: A total of 669 children under age 18 were included in the study. The median of dinner time was 8:30 pm. Late dinner eaters accounted for a higher proportion of acute otitis media than early dinner eaters (7% vs 3%; P=0.028). Other infectious diseases were not associated with dinner time habits. Conclusions: We make a preliminary estimate of the link between late dinner habits and acute otitis media in children. However, no conclusions about causality can be established due to the observational design of the study.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

The microgrid is a small-scale, autonomous decentralized power plant with its own distributed generation, storage capacity and multiple loads, with the capacity to function in grid interconnected and an island mode. The decentralized control of microgrids with parallel operated voltage source converters (VSCs) is proposed in this paper to improve power quality using a machine learning approach. The DNN based MPPT controller is proposed and its best performance is presented. The SRF-PLL is utilized for AC side synchronization in VSC control. The proposed microgrid involves two PV arrays fed to two voltage source converters along with their independent controls, connected in parallel through LC filters and line coupling transformers and serves the loads at PCC. The proposed model is simulated using MATLAB/Simulink. The dq-framed inner loop control is employed to individually regulate the real and reactive power at the point of common coupling. Furthermore, the proposed model is analyzed and compared by employing a mathematical model of AC system dynamics, inner loop control, output voltage quality, AC harmonic spectrum analysis, and total harmonic distortion (THD) in both grid interconnected and island mode. In island mode, AC harmonic spectrum and THD are accomplished within the permissible range.

The service conditions of underground coal mine equipment are poor, and it is difficult to accurately extract the fault characteristics of rolling bearings. In order to better improve the accuracy of fault identification of rolling bearings, a fault detection method based on multiscale permutation entropy and SOA-SVM is proposed. First, the whale optimization algorithm is used to select the modal analysis number K and the penalty factor α of the variational mode decomposition algorithm. Then, the vibration signal of rolling bearings is dissolved according to the optimized variational mode decomposition algorithm, and the multi-scale permutation entropy of the main intrinsic mode function is calculated. Finally, the feature values of the matrix are entered into the SVM algorithm optimized by the seagull optimization algorithm to obtain the classification result. The experimental results based on the published rolling bearing datasets of Western Reserve University show that the identification success rate of the proposed method can reach 98.75%. The fault detection of the rolling bearings can be completed accurately and efficiently.

Numerical methods, including machine learning methods, are now actively used in the applications related to guided wave propagation. The method proposed in this study for material properties characterization is based on the algorithm of the clustering of multivariate data series obtained as a result of the application of the matrix pencil method to the experimental data. In the proposed technique, multi-objective optimization is employed to improve the accuracy of particular parameter identification. At the first stage, the computationally efficient method based on the calculation of the Fourier transform of Green's matrix is employed iteratively and the obtained solution is used for the filter construction with decreasing bandwidth, which allows us to obtain nearly noise-free classified data (with mode separation). The filter provides data separation between all guided waves in a natural way, which is needed at the second stage, where the slower method based on the minimization of the slowness residuals is applied to the data. The method might be applied for material properties identification in plates with thin coatings/interlayers, multi-layered anisotropic laminates etc.

The authors of the article performed computer simulation of buffer amplifiers (BA), which have medium and extremely small values of the offset voltage's systematic component (V_off), for different technological processes (Si, GaAs and GaN). The proposed control units are distinguished by a small number of elements and allow operation in the range of low and high temperatures. The variants of circuitry implementation of control units based on GaAs, GaN depletion-mode CMOS and JFET technological processes are considered. The results of the comparative modeling showed that the basic circuit of the BA on two field-effect transistors, when implemented on various modifications of GaN MOS and depletion-mode MOS transistors, provides sufficiently low values of the offset voltage's systematic component (less than 2 μV). The proposed BAs are designed for use in the structure of the Sallen-Key low-pass filter (LPF) when they are implemented both on mid-frequency Si CJFET and on GaAs microwave transistors. Low values of the LPF V_off have a positive effect on the effective capacity of the ADC. An example of switching on a BA in the JFET OpAmp structure based on the depletion-mode MOS input stage and a “folded” cascode, which, with 100% negative feedback, can be used in the Sallen-Key LPF, is considered. Computer simulation of the JFET/MOS OpAmp showed that the OpAmp has an open-loop voltage gain of 76-85dB, and its V_off is within 7µV in the temperature range from -60°C to +120°C. The presented circuitry of buffer amplifiers is intended, first of all, for the tasks of designing precision Sallen-Key low-pass filter (low-pass filter, high-pass filter, PF, RF).

This work presents results of property researches of fabricated samples of silica few-mode optical fiber (FMF) with induced chirality under twisting 10 and 66 revolutions per meter, core diameter 11 µm, typical “telecommunication” cladding diameter 125 µm and improved height of quasi-step refractive index profile. Proposed FMF supports 4 guided modes over “C”-band. We represent results of computed characteristics, as well as experimentally measured spectral responses of laser-excited optical signals, including researches and analysis of few-mode effects, occurring after fiber Bragg grating writing.

Micro-grids’ operations offer local reliability; in the event of faults or low voltage/frequency events on the utility side, micro-grids can disconnect from the main grid and operate autonomously while providing the continued supply of power to local customers. With the ever-increasing penetration of renewable generation, however, the operations of micro-grids become increasingly complicated because of the associated fluctuations of voltages. As a result, transformer taps are adjusted frequently, thereby leading to the fast degradation of expensive tap-changer transformers. In the islanding mode, the difficulties also come from the drop of voltage and frequency upon disconnecting from the main grid. To appropriately model the above, the nonlinear AC power flow constraints are necessary. Computationally, the discrete nature of tap-changer operations and the stochasticity caused by renewables add two layers of difficulty on top of a complicated AC-OPF problem. To resolve the above computational difficulties, the main principles of the recently-developed "l1-proximal" Surrogate Lagrangian Relaxation are extended. Testing results based on 9-bus system demonstrate the efficiency of the method to obtain the exact feasible solutions for micro-grid operations thereby avoiding approximations inherent to existing methods, while demonstrating that through the optimization, 1. the number of tap changes is drastically reduced, and 2. the method is capable of handling networks with meshed topologies.

An increasing body of evidence shows that seaweeds, including kelp, can be used as a tool to neutralize or remove excess nutrients and metals from the water column. Here we report on a preliminary field assessment showing potential nutrient and carbon removal differences by sugar kelp and ribbon kelp grown in common gardens. Seawater and tissue samples were collected systematically from two farms in Alaska. Results show differences between % N and % C content between ribbon kelp (Alaria marginata) and sugar kelp (Saccharina latissima). Results also show that tissue nitrogen in ribbon kelp varies sharply due to nitrogen availability in the water column. In contrast, the percentage of tissue N in sugar kelp remains comparatively stable. Our outcomes provide insight into potential differences in nutrient removal and harvest timing for different kelp species.

This paper studies the performance improvement of the IEEE 802.15.4 nonbeacon-enabled mode originated by the inclusion of the Request-To-Send/Clear-To-Send (RTS/CTS) handshake mechanism resulting in frame concatenation. Under IEEE 802.15.4 employing RTS/CTS, the backoff procedure is not repeated for each data frame sent but only for each RTS/CTS set. The maximum throughput and minimum delay performance are mathematically derived for both the Chirp Spread Spectrum and Direct Sequence Spread Spectrum Physical layers for the 2.4 GHz band. Results show that the utilization of RTS/CTS significantly enhances the performance of IEEE 802.15.4 applied to healthcare in terms of bandwidth efficiency.

Camouflage is an interesting adaptation (for survivability) by organisms in terms of different aggregation or fusion of colourations. Understanding these camouflage strategies in the presence of arsenic on transparent/semi-transparent species is pretty challenging. Previously, several researchers have demonstrated that colouration or pigmentation strategy in an organism is a strategy to merge with the environment to escape from predatory threats. Our study was done on a semi-transparent freshwater prawn species which exhibits a strategy of pigment droplets on its exoskeleton. Unlike previous studies, our findings robustly indicate the fact that pigment droplets are not the only reason for colouration. The pigment droplets rather regulate the darkness of the exoskeleton. However, the transparency of the abdominal muscles additionally plays a crucial role in creating a background of the pigment droplets. The transparency muscles allow light to pass through the abdomen, thus creating a semi-transparent appearance. The degree of semi-transparency is also regulated by the intensity of light. The abdomen and the pigment droplets on the exoskeleton cumulatively as well as contrastingly maintain the transparency and the colour quotient of the prawns. In our study, we have majorly concentrated on the abdominal region of the prawns as it appears to be the key semi-transparent feature of the organism. This research is directed to an ecotoxicological aspect where we showed that arsenic in chronic non-lethal concentration, can notably alter the colouration pattern in this prawn model within a short period of time. Finally, we have used an image processing algorithm to assess the alteration of colouration in this organism.

This paper intends to examine whether a company’s policy of dividend would impact or influence the price fluctuation of respective common stock in the designated stock market particularly in Hong Kong. Hence, there are 354 companies in Hong Kong which are all listed company on the Stock Exchange of Hong Kong (HKEX), were chosen as sample data for analysis with their audited financial information ranged from 2001 to 2020. Two proxies, the yield and the ratio of pay-out of dividend were widely adopted for the measurement of the effect of dividend policy and the possible influence on the volatility of respective common stock price by employing two statistical models, which are the model of fixed and random effects to provide accurate regression coefficients. With the results from the model of fixed effects, the yield and the pay-out ratio of dividend have been found statistically associated to the price volatilization of respective common stock in Hong Kong. The statical results in this study also find the yield and the ratio of pay-out of dividend are apparently and negatively associated to the price volatilization of respective common stock in Hong Kong. The research outcomes will be a reference for further study on different variables may have effects or volatilize the price of common stock price particularly in Hong Kong capital market.

Enabling D2D communication in the mm-Wave band has many obstacles which must be mitigated. The primary concern is the introduction of interference from various sources. Thus, we focused our work on the performance of decode and forward (DF) relay assisted D2D communication in the mm-Wave band for increasing the coverage probability and energy efficiency (EE). Three modes are proposed for D2D communication to prevail. Bit-wise binary XOR operation is executed at the relay node which increases the security feature. Radius of coverage expression is derived which indicates the switching of the modes. The diffused incoherent scattering power is also considered as a part of power consumption. Furthermore, a unique relay selection scheme, Dynamic relay selection (DRS) method is proposed to select the optimal relay for information exchange. Comparison of the proposed DF relay scheme with amplify and forward (DF) scheme is also shown. Finally, simulation results prove the efficacy of the proposed work.

Training supervised machine learning models requires labeled examples. A judicious choice of examples is helpful when there is a significant cost associated with assigning labels. This article improves upon a promising extant method – Batch-mode Expected Model Change Maximization (B-EMCM) method – for selecting examples to be labeled for regression problems. Specifically, it develops and evaluates alternate strategies for adaptively selecting batch size in B-EMCM. By determining the cumulative error that occurs from the estimation of the stochastic gradient descent, a stop criteria for each iteration of the batch can be specified to ensure that selected candidates are the most beneficial to model learning. This new methodology is compared to B-EMCM via mean absolute error and root mean square error over ten iterations benchmarked against machine learning data sets. Using multiple data sets and metrics across all methods, one variation of AB-EMCM, the max bound of the accumulated error (AB-EMCM Max), showed the best results for an adaptive batch approach. It achieved better root mean squared error (RMSE) and mean absolute error (MAE) than the other adaptive and non-adaptive batch methods while reaching the result in nearly the same number of iterations as the non-adaptive batch methods.

The aim of the studies was to test the hydraulic pressure losses along the length, local pressure losses, absolute and relative roughness values of the pipeline walls made of modern polymer material. The article presents the results of the experimental studies of hydraulic resistance of pipelines from modern polymer materials, the method of theoretical determination of resistance coefficients in the VALTEC ISO 21003 metal polymer pipeline, the classification and method of determining the values of local hydraulic resistance coefficients of T-Junctions are given, the dependence for determining the Darcy λ hydraulic friction coefficient associated with the value of the equivalent hydraulic roughness coefficient of the inner surface of pipes and the Reynolds number. The experimental data of the hydraulic coefficient of friction Darcy λ was compared with the known theoretical relationships of A.D. Altschul, Colbrooke for smooth pipes, Colbrooke and White, an alternative to the Colbrooke-White, Offengenden equation for low-shear pipes and pipes from polymer materials with Reynolds numbers Re>10^4. Dependence of hydraulic coefficient of friction on relative equivalent roughness of pipeline walls and Reynolds number, specific energy loss per one linear meter on total flow rate in system of hydraulically short pipeline is obtained. The empirical dependence of values of coefficients of local resistance ζ=f(Q2/Q3) from a ratio of the divided expenses of Q2/Q3 of the equal-pass T-Junction α=90 the pipeline to a branch up, on pass in the direct T-Junction and division of streams at various internal pipeline diameters of VALTEC.

Manufacturing corporations has the acceptance of the Outsourcing Process (OP) to improve industrial activities as well as to archive the revenue objectives, and with this, Risk Analysis (RA) tools are constantly used to assure expected results. Failure Mode and Effect Analysis (FMEA) is one of preferred RA tools, moreover, it is proven that FMEA adds uncertainty because of the human participation at the RA, afterward it is demonstrated that Pythagorean Fuzzy Dimensional Analysis – FMEA – Value Stream Mapping (PFDA-FMEA-VSM) method removes the uncertainty in RA, likewise it aids to the stakeholders for decision making, giving more advantages improving the use of the resources on the project. This document exhibits a real case scenario in a manufacturing firm applying PFDA-FMEA-VSM method adapted for manufacturing OP. The application of PFDA-FMEA-VSM shows solid RA results, removing the human intervention uncertainty added to the risk ranking, gives advantages to the stakeholders for visualize the main risks in detailed diagram, as well as make easier to take better decisions on where to apply resources and mitigate risks during OP.

Every intervention of planning, implementation, and monitoring of agricultural and agri-environmental policies requires assessment tools that should have the characteristics of relevance, completeness, interpretability, data quality, efficiency, and overlapping. Despite the extensive selection of bibliographies and numerous projects designed to develop agri-environmental indicators necessary for assessing the sustainability of new policies, it is difficult to have an integrated and updated set of indicators available, which can be an effective and practical application tool to assists policymakers, researchers, and actors in policy design, monitoring and impact assessment. Particularly, such need is pressing to face the new environmental challenges imposed by the upcoming European Union Green Deal on the Common Agricultural Policy (CAP) post 2023. This study, therefore, aims to fill this gap by proposing a selection methodology and different pools of agri-environmental indicators differentiated based on a scale approach (crop-farm-district-region). Furthermore, we have attempted to validate our approach by quantifying selected indicators for a specific evaluation necessity, represented in this case by an assessment of environmental impact of land use change induced by CAP greening requirements in the Northern Italy context. Results of this validation show original crops’ impacts comparison, but also highlight great knowledge gaps in the available literature.

This paper investigates the path following control problem for a unmanned surface vehicle (USV) in the presence of unknown disturbances and system uncertainties. The simulation study combines two different types of sliding mode surface based control approaches due to its precise tracking and robustness against disturbances and uncertainty. Firstly, an adaptive linear sliding mode surface algorithm is applied, to keep the yaw error within the desired boundaries and then an adaptive integral non-linear sliding mode surface is explored to keep an account of the sliding mode condition. Additionally, a method to reconfigure the input parameters in order to keep settling time, yaw rate restriction and desired precision within boundary conditions is presented. The main strengths of proposed approach is simplicity, robustness with respect to external disturbances and high adaptability to static and dynamics reference courses without the need of parameter reconfiguration.

This paper presents three types of sliding mode controllers for a magnetic levitation system. First, a proportional-integral sliding mode controller (PI-SMC) is designed using a new switching surface and a proportional plus power rate reaching law. The PI-SMC is more robust than a feedback linearization controller in the presence of mismatched uncertainties and outperforms the SMC schemes reported recently in the literature in terms of the convergence rate and settling time. Next, to reduce the chattering phenomenon in the PI-SMC, a state feedback-based discrete-time SMC algorithm is developed. However, the disturbance rejection ability is compromised to some extent. Furthermore, to improve the robustness without compromising the chattering reduction benefits of the discrete-time SMC, mismatched uncertainties like sensor noise and track input disturbance are incorporated in a robust discrete-time SMC design using multirate output feedback (MROF). With this technique, it is possible to realize the effect of a full-state feedback controller without incurring the complexity of a dynamic controller or an additional discrete-time observer. Also, the MROF-based discrete-time SMC strategy can stabilize the magnetic levitation system with excellent dynamic and steady-state performance with superior robustness in the presence of mismatched uncertainties. The stability of the closed-loop system under the proposed controllers is proved by using the Lyapunov stability theory. The simulation results and analytical comparisons demonstrate the effectiveness and robustness of the proposed control schemes.

In this article, the main building of the former Uto City Hall, which was severely damaged in the 2016 Kumamoto earthquake, is investigated as a case study for the retrofitting of an irregular Reinforced Concrete building using the base-isolation technique. Its peak response is predicted via mode-adaptive bidirectional pushover analysis (MABPA), which was originally proposed by the authors. In the prediction step of MABPA, the peaks of the first and second modal responses are predicted considering the energy balance during a half cycle of the structural response. The numerical analysis results show that the peak relative displacement can be properly predicted by MABPA. The results also show that the performance of the retrofitted building models is satisfactory for the ground motion considered in this study, including the recorded motions in the 2016 Kumamoto earthquake.

A data-driven analysis method known as dynamic mode decomposition (DMD) approximates the linear Koopman operator on projected space. In the spirit of Johnson-Lindenstrauss Lemma, we will use random projection to estimate the DMD modes in reduced dimensional space. In practical applications, snapshots are in high dimensional observable space and the DMD operator matrix is massive. Hence, computing DMD with the full spectrum is infeasible, so our main computational goal is estimating the eigenvalue and eigenvectors of the DMD operator in a projected domain. We will generalize the current algorithm to estimate a projected DMD operator. We focus on a powerful and simple random projection algorithm that will reduce the computational and storage cost. While clearly, a random projection simplifies the algorithmic complexity of a detailed optimal projection, as we will show, generally the results can be excellent nonetheless, and quality understood through a well-developed theory of random projections. We will demonstrate that modes can be calculated for a low cost by the projected data with sufficient dimension.

Modelling errors, robust stabilization/tracking problems under parameter and model uncertainties complicate the control of the flexible underactuated systems. Chattering-free sliding-mode based input-output control law realizes robustness against the structured and unstructured uncertainties in the system dynamics and avoids excitation of unmodeled dynamics. The main purpose is to propose a robust adaptive solution for stabilizing and tracking direct-drive (DD) flexible robot arms under parameter and model uncertainties, as well as external disturbances. A lightweight robot arm subject to external and internal dynamic effects was taken into consideration. The challenges are compensating actuator dynamics with the inverter switching effects and torque ripples, stabilizing the zero dynamics under parameter/model uncertainties and disturbances while precisely track the predefined reference position. The precise control of this kind of system demands an accurate system model and knowledge of all sources that excite unmodeled dynamics. For this purpose, equations of motion for a flexible robot arm were derived and formulated for the large motion via Lagrange’s method. The goals were determined to achieve high-speed, precise position control, and satisfied accuracy by compensating the unwanted torque ripple and friction that degrades performance through an adaptive robust control approach. The actuator dynamics and their effect on the torque output were investigated due to the transmitted torque to the load side. The high-performance goals, precision&robustness issues, and stability concerns were satisfied by using robust-adaptive input-output linearization-based control law combining chattering-free sliding mode control (SMC) while avoiding the excitation of unmodeled dynamics.

Rhenium Disulfide (ReS2) has evolved as a novel 2D transition-metal dichalcogenide (TMD) material which has promising applications in optoelectronics and photonics because of its distinctive anisotropic attributes. In this review, we emphasize on formulating saturable absorbers (SAs) based on ReS2 to produce Q-switched and mode-locked pulsed lasers of diverse operation wavelengths like 1 μm, 1.5 μm, 2 μm, and 3 μm. We outline ReS2 synthesis techniques and integration platforms concerning solid-state and fiber-type lasers. We discuss the laser performance based on SAs attributes. Lastly, we draw conclusions and outlook by recommending additional improvements for SA devices so as to advance the domain of ultrafast photonic technology.

This article is a big picture of how electrical noise or conducted Electromagnetic Interference (EMI) is generated and mitigated in power converters. It gives an overview of what EMI in power converters is – from generation through to conduction and mitigation. It is meant to cover the complete subject as a summary so that the reader will have an outline of how to control conducted EMI by design (where possible) and how to mitigate by filtering. A clear distinction is made between Differential Mode (DM) and Common Mode (CM) EMI generation and mitigation. By using a boost converter as an example the trade-offs for DM noise control are discussed. It is shown how CM EMI is generated in a boost converter using the concept of the “Imbalance Difference Model” (IDM). Practical measurements for an in-line power filter is given showing the effect of the filter on the total EMI of a boost converter. Measurements for the CM current produced due to the imbalance difference for different values of the boost conductor are also shown. The main contribution of this study is linking CM noise generation to DM EMI. It is shown that CM noise is a direct consequence of DM noise (although circuit imbalance and coupling to a common ground also play a role). This paper will be useful to designers seeking the “bigger picture” of how EMI is generated in power converters and what can be done to mitigate the noise.

In this paper, the problem of observer-based adaptive sliding mode control is discussed for nonlinear systems with sensor and actuator faults. The time-varying actuator degradation factor and external disturbance are considered in the system simultaneously. In this study, the original system is described as a new normal system by combining the state vector, sensor faults and external disturbance into a new state vector. For the augmented system, a new sliding mode observer is designed, where a discontinuous term is introduced such that the effects of sensor and actuator faults and external disturbance will be eliminated. In addition, based on a tricky design of the observer, the time-varying actuator degradation factor term is developed in the error system. On the basis of the state estimation, an integral-type adaptive fuzzy sliding mode controller is constructed to ensure the stability of the closed-loop system. Finally, the effectiveness of the proposed control methods can be illustrated with a numerical example.

Glufosinate, a glutamine synthetase (GS) inhibitor, often provides variable weed control depending on environmental conditions such as light, temperature and humidity at the time of application. Midday applications normally provide improved efficacy compared to applications at dawn or dusk. We investigated the physiological, molecular, and biochemical basis for the time-of-day effect on glufosinate efficacy in Amaranthus palmeri. GS1 and GS2 gene expression and protein abundance were assessed in different parts (young leaves, old leaves, and roots) of plants incubated in the dark compared to those in the light. The turnover of GS total activity was also evaluated overtime following glufosinate treatment at midday compared to dusk application. The results suggest that GS in A. palmeri is less expressed and less abundant in the dark compared to in the light. Midday application of glufosinate under intense light conditions in the hours following application provide full control of A. palmeri plants. Consequently, these plants are unable to recover GS activity by de novo protein synthesis. Full activity of GS is required for complete inhibition by the irreversible inhibitor glufosinate. Therefore, glufosinate applications should always be performed in the middle of the day when sunlight is intense, to prevent weed escapes from the herbicide treatment.

Power generation systems based on renewable energy sources are finding ever-widening applications and many researchers work on this problem. Many papers address the problem of transformerless structures, but few of them are aimed at conducting research on structures with multilevel converter topologies. In this paper a grid-tied transformerless PV-generation system based on a multilevel converter is discussed. There are common-mode leakage currents which act as a parasitic factor. It is also known that common-mode voltage is the main cause of the common-mode leakage current in grid-tied PV-generation systems. This paper considers the space vector pulse-width modulation (PWM) technique which is used to suppress or reduce common-mode leakage current. The proposed engineering solutions for a generation system based on the multilevel converter controlled with a pulse-width modulation technique are verified by experiment.

Abstract: To describe the feeder topology and information exchange between intelligent electronic devices (IEDs) for Internet of Things (IoT), it is necessary to extend IEC 61850 and add a logical model. The feeder model described in IEC 61970 is then extended in IEC 61850 to serve as a container for the equipment along the distribution line. For the physical connections in the electrical equipment, both terminal and connectivity node logical models are added. Taking logical node XCBR as the example, its attributes for the terminals are added to the electrical equipment. The logical node LCNN is then further added in order to describe the connectivity node. By next adding the logical node LTPN to describe the topological node, and FTPA to describe the results of the topology analysis, we can efficiently describe the topology analysis results. Based on these new logical nodes, the exchange of topology information between intelligent terminals no longer relies on configuration files, but only requires logical nodes. Through the above expansion, the topology description and information exchange of medium and low voltage feeders are realized.

Since people spend most of their time in indoor environments, the objective of this work was to study indoor air quality perception and its effects on users’ thermal comfort. Based on previous data from a building with a central air-conditioning system and two mixed-mode buildings located in the humid subtropical climate of Florianópolis, southern Brazil, statistical analyses were performed. Each user subjective answer obtained through a questionnaire was combined with the corresponding environmental conditions – measured using microclimate stations, a portable thermo-anemometer and a CO2 analyser. Results showed that improvement in air quality was associated with the reduction of air temperature and humidity ratio. Also, there was a significant influence of thermal, air movement and humidity sensation and acceptability of air quality perception. Users felt more satisfied or neutral with air quality for being in thermal comfort, and not because of the CO2 level – which means that air quality perception is influenced by factors other than CO2. This study recommends the implementation of an air exchange device in split air-conditioners with air recirculation used in mixed-mode buildings in Brazil. It is important to provide suitable indoor ventilation to reduce pollutants concentration, ensure good air quality and prevent respiratory diseases.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

This paper combines a literature survey and data analysis. The literature on the Subtropical Front (STF) in the Southern Ocean is reviewed with a two-pronged emphasis on the double-front structure of the STF, hence the existence of a subtropical frontal zone (STFZ), and the circumpolar continuity of the STFZ. The data analysis is based on the World Ocean Circulation Experiment (WOCE) sections. The STFZ is detected along each section independently from other sections, while moving circum-polarly downstream (eastward). The literature survey and data analysis confirm the circumpolar continuity of the STFZ extending from the Brazil Current across the South Atlantic, South Indian, and South Pacific up to Chile, being bound by the North and South STF. The circumpolar continuity of the STFZ is partly interrupted by South Africa and Tasmania, where the North STF ceases, while the South STF continues eastward. The South Atlantic STFZ is the southern boundary of the well-defined Subtropical Mode Water (STMW) thermostad, which cools eastward from 15°C to 11°C between the Brazil Current and Greenwich Meridian. In the southeast Pacific, the STFZ is the southern boundary of the 17-to-19°C thermostad (South Pacific Eastern STMW). The STFZ’s vertical extent is at maximum in the South Atlantic (>1000 m), decreasing eastward to 300 m in the southeast Pacific off Chile. A special attention is given to the South Pacific and the STFZ’s role in the ecology of Chilean jack mackerel Trachurus murphyi that spawn at the STFZ and migrate along the STFZ from Chile up to New Zealand.

This paper presents an improved droop control strategy for grid-connected inverter power stability and power quality under distorted with consideration of grid fluctuation and inter-harmonics. An instantaneous frequency without PLL and amplitude of capacitor voltage feed-forward control strategy is given to power stability control, meanwhile a grid current feedback control is given by an incomplete derivation with a high-pass filter, so that the harmonics and inter-harmonics current can be suppressed. These approaches can provide both good active and reactive power dynamic response under fluctuation of frequency, and rejection ability against harmonic and inter-harmonic voltage. Based on model of inverter, the proposed control strategies are designed in detail. Simulations and experiments are present to validate the effectiveness of proposed method.

This study investigates circulation types (CTs) in Africa, south of the equator, that are related to wet and dry conditions in Western Cape, the statistical relationship between the selected CTs and the Southern Annular Mode (SAM), and changes in the frequency of occurrence of the CTs related to the SAM under the ssp585 scenario. Obliquely rotated principal component analysis applied to sea level pressure was used to classify CTs in Africa, south of the equator. Three CTs were found to have a high probability to be associated with wet days in Western Cape, and four CTs were equally found to have a high probability to be associated with dry days in Western Cape. Generally, the dry/wet CTs feature the southward/northward track of the mid-latitude cyclone, adjacent to South Africa; anti-cyclonic/cyclonic relative vorticity, and poleward/equatorward track of westerlies, south of South Africa. One of the selected wet CTs is significantly related to variations of the SAM. Years with an above-average SAM index correlate with the below-average frequency of occurrence of the wet CT. The results suggest that through the dynamics of the CT, the SAM might control the rainfall variability of Western Cape. Under the ssp585 scenario, the analyzed climate models indicated a possibility in the decrease of the frequency of occurrence of the aforementioned wet CT associated with cyclonic activity at the mid-latitudes, and an increase in the frequency of occurrence of the CT associated with enhanced SLP in the mid-latitudes.

Recent brain imaging findings by using different methods (e.g., fMRI and PET) have suggested that social anxiety disorder (SAD) is correlated with alterations in regional or network-level brain function. However, due to many limitations associated with these methods, such as poor temporal resolution and limited number of samples per second, neuroscientists could not quantify the fast dynamic connectivity of causal information networks in SAD. In this study, SAD-related changes in brain connections within the default mode network (DMN) were investigated using eight electroencephalographic (EEG) regions of interest. Partial directed coherence (PDC) was used to assess the causal influences of DMN regions on each other and indicate the changes in the DMN effective network related to SAD severity. The DMN is a large-scale brain network basically composed of the mesial prefrontal cortex (mPFC), posterior cingulate cortex (PCC)/precuneus, and lateral parietal cortex (LPC). The EEG data were collected from 88 subjects (22 control, 22 mild, 22 moderate, 22 severe) and used to estimate the effective connectivity between DMN regions at different frequency bands: delta (1–3 Hz), theta (4–8 Hz), alpha (8–12 Hz), low beta (13–21 Hz), and high beta (22–30 Hz). Among the healthy control (HC) and the three considered levels of severity of SAD, the results indicated a higher level of causal interactions for the mild and moderate SAD groups than for the severe and HC groups. Between the control and the severe SAD groups, the results indicated a higher level of causal connections for the control throughout all the DMN regions. We found significant increases in the mean PDC in the delta (p = 0.009) and alpha (p = 0.001) bands between the SAD groups. Among the DMN regions, the precuneus exhibited a higher level of causal influence than other regions. Therefore, it was suggested to be a major source hub that contributes to the mental exploration and emotional content of SAD. In contrast to the severe group, HC exhibited higher resting-state connectivity at the mPFC, providing evidence for mPFC dysfunction in the severe SAD group. Furthermore, the total Social Interaction Anxiety Scale (SIAS) was positively correlated with the mean values of the PDC of the severe SAD group, r (22) = 0.576, p = 0.006 and negatively correlated with those of the HC group, r (22) = −0.689, p = 0.001. The reported results may facilitate greater comprehension of the underlying potential SAD neural biomarkers and can be used to characterize possible targets for further medication.

Diagnostics and decomposition of atmospheric disturbances in a planar flow are considered and applied to numerical modeling results with the direct possibility to use in atmosphere monitoring especially in such strong events which follow magnetic storms. The study examines a situation in which the stationary equilibrium temperature of a gas may depend on a vertical coordinate, that seriously complicates the problem solution. The relations connecting perturbations for acoustic and entropy modes are analytically established and led to the solvable diagnostic equations. These perturbation structures, found as the equation solutions specify acoustic and entropy modes in an arbitrary stratified gas under the condition of stability. These time-independent diagnostic relations link gas perturbation variables of the acoustic and the entropy modes. Hence, they provide the ability to decompose the total vector of perturbations into acoustic and non-acoustic (entropy) parts uniquely at any instant within the all accessible heights range. As a prospective model, we consider the diagnostics at the height interval [120;180] km, where the equilibrium temperature of a gas depends linearly on the vertical coordinate. For such a heights range it is possible to proceed with analytical expressions for pressure and entropy perturbations of gas variables. Individual profiles of acoustic and entropy parts for some data, obtained by numerical experiment, are illustrated by the plots for the pure numerical data against ones obtained by the model. The total energy of a flow is determined for both approaches and its height profiles are compared.

Research Highlights: Data of advanced-age provenance tests were reanalyzed applying a new approach, to directly estimate the growth of populations at their original sites under individually generated future climates. The results reveal surprisingly high resilience potential of fir species. Background and Objectives: The growth and survival of silver fir under future climatic scenarios is insufficiently investigated at the xeric limits. The selective signature of past climate determining the current and projected growth was investigated to analyze the prospects of adaptive silviculture and assisted transfer of silver fir populations, and of the introduction of non-autochthonous species. Materials and Methods: Hargreaves’ climatic moisture deficit was selected to model height responses of adult populations. Climatic transfer distance was used to assess the relative drought stress of populations at the test site, relating these to the past conditions to which the populations had adapted. ClimateEU and ClimateWNA pathway RCP8.5 data served to determine individually past, current, and future moisture deficit conditions. Beside silver fir, other fir species from South Europe and the American Northwest were also tested. Results: Drought tolerance profiles explained the responses of transferred provenances and predicted their future performance and survival. Silver fir displayed significant within-species differentiation regarding drought stress response. Applying the assumed drought tolerance limit of 100mm relative moisture deficit, most of the tested silver fir populations seem to survive their projected climate at their origin until the end of the century. Survival is likely also for transferred Balkan fir species and for grand fir populations, but not for the Mediterranean species. Conclusions: The projections are less dramatic than provided by usual field assessments. Some results contradict generally accepted concepts. The method fills the existing gap between experimentally determined adaptive response and the predictions needed for management decisions. It also underscores the unique potential of provenance tests.

There is a need to search for new antifungals, especially for the treatment of the invasive Candida infections, caused mainly by C. albicans. These infections are steadily increasing at an alarming rate, mostly among immunocompromised patients. The newly synthesized compounds (3a-3k) were characterized by physico-chemical parameters and investigated for antimicrobial activity using the microdilution broth method to estimate minimal inhibitory concentration (MIC). Additionally, their antibiofilm activity and mode of action together with the effect on the membrane permeability in C. albicans were investigated. Biofilm biomass and its metabolic activity were quantitatively measured using crystal violet (CV) staining and tetrazolium salt (XTT) reduction assay. The cytotoxic effect on normal human lung fibroblasts and hemolytic effect were also evaluated. The results showed differential activity of the compounds against yeasts (MIC = 0.24-500 µg/mL) and bacteria (MIC = 125-1000 µg/mL). Most compounds possessed strong antifungal activity (MIC = 0.24-7.81 µg/mL). The compounds 3b, 3c, and 3e, showed no inhibitory (at 1/2 MIC) and eradication (at 8 x MIC) effect on C. albicans biofilm. Only slight decrease in the biofilm metabolic activity was observed for compound 3b. Moreover, the studied compounds increased the permeability of the membrane/cell wall of C. albicans and their mode of action may be related to action within the fungal cell wall structure and/or within the cell membrane. It is worth noting that the compounds had no cytotoxicity effect on pulmonary fibroblasts and erythrocytes at concentrations showing anticandidal activity. The present studies in vitro confirm that these derivatives appear to be a very promising group of antifungals for further preclinical studies.

Parascaris sp. is the only ascarid parasitic nematode in equids and one of the most threatening infectious organisms in horses. Only a limited number of compounds are available for treatment of horse helminthiasis and Parascaris sp. worms have developed resistance to the three major anthelmintic families. In order to overcome the appearance of resistance, there is an urgent need for new therapeutic strategies. The active ingredients of herbal essential oils are potentially effective antiparasitic drugs. Carvacrol is one of the principal chemicals of essential oil from Origanum, Thymus, Coridothymus, Thymbra, Satureja and Lippia herbs. However, the antiparasitic mode of action of carvacrol is poorly understood so far. Here, the objective of the work was to characterize the activity of carvacrol on Parascaris sp. nicotinic acetylcholine receptors (nAChRs) function both in vivo with the use of worm neuro-muscular flap preparations and in vitro with two-electrode voltage-clamp electrophysiology on nAChRs expressed in Xenopus oocytes. We have developed a neuromuscular contraction assay on Parascaris body flaps and obtained acetylcholine concentration-dependent contraction responses. Strikingly, we observed that 300 µM carvacrol fully and irreversibly abolished Parascaris sp. muscle contractions elicited by acetylcholine. Conversely, carvacrol antagonized acetylcholine-induced currents from both the nicotine-sensitive AChR and the morantel-sensitive AChR subtypes. Thus, we show for the first time that the body muscle flap preparation is a tractable approach to investigate the pharmacology of Parascaris sp. neuro-muscular system. Our results suggest an intriguing mode of action for carvacrol being a potent antagonist of muscle nAChRs of Parascaris sp. worms which may account for its antiparasitic potency.

In this paper, we prove some common fixed point theorems on complex partial metric space. The presented results gener- alize and expand some of the literature well-known results. We also explore some of the application of our key results.

We propose and theoretically investigate integrated photonic filters based on coupled Sagnac loop reflectors (SLRs) formed by a self-coupled wire waveguide. By tailoring coherent mode interference in the device, three different filter functions are achieved, including Fano-like resonances, wavelength interleaving, and varied resonance mode splitting. For each function, the impact of device structural parameters is analyzed to facilitate optimized performance. Our results theoretically verify the proposed device as a compact multi-functional integrated photonic filter for flexible spectral shaping.

Two-dimensional mass spectrometry (2D MS) is a method for tandem mass spectrometry that relies on manipulating ion motions to correlate precursor and fragment ion signals. 2D mass spectra are obtained by performing a Fourier transform in both the precursor ion mass-to-charge ratio (m/z) dimension and the fragment ion m/z dimension. The phase of the ion signals evolves linearly in the precursor m/z dimension and quadratically in the fragment m/z dimension. This study demonstrates that phase-corrected absorption mode 2D mass spectrometry improves signal-to-noise ratios by a factor of 2 and resolving power by a factor of 2 in each dimension compared to magnitude mode. Furthermore, phase correction leads to an easier differentiation between ion signals and artefacts, and therefore easier data interpretation.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

The group III two-component hybrid histidine kinase MoHik1p in the filamentous fungus Magnaporthe oryzae is known to be a sensor for external osmotic stress and essential for the fungicidal activity of the phenylpyrrole fludioxonil. The mode of action of fludioxonil has not yet been completely clarified but rather assumed to hyperactivate the high osmolarity glycerol (HOG) signaling pathway. To date, not much is known about the detailed molecular mechanism of how osmotic stress is detected or fungicidal activity is initiated within the HOG pathway. The molecular mechanism of signaling was studied using a mutant strain in which the HisKA signaling domain was modified by an amino acid change of histidine H736 to alanine A736. We found that MoHik1pH736A is as resistant to fludioxonil but not as sensitive to osmotic stress as the null mutant ∆Mohik1. H736 is required for fludioxonil action but is not essential for sensing sorbitol stress. Consequently, this report provides evidence of the difference in the molecular mechanism of fludioxonil action and the perception of osmotic stress. This is an excellent basis to understand the successful phenylpyrrole-fungicides’ mode of action better and will give new ideas to decipher cellular signaling mechanisms.