Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

Friction Stir Welding is a suitable solid-state joining technology to connect dissimilar materials. To produce an effective joint, it requires a phase of optimization which leads to the definition of process parameters such as pin geometry, tool rotational speed, rotation direction, welding speed, thickness of the sheets or tool tilt angle. The aim of this review is to present a complete and detailed frame of the main process parameters and their effect on the final performance of a friction stir welded joint in terms of mechanical properties and microstructure. Particularly, the attention was focused on the connection between different aluminum alloys. Moreover, the experimental results were correlated to the development and the applications of tools, which can effectively use in the design of the manufacturing process, such as finite element analyses, artificial neural networks, statistical studies. The review wants to be also a point of reference to identify the best combinations of process parameters based on the dissimilar aluminum to be joined.

The present work aims to explain the aluminum hydrolysis reaction kinetics based on properly chosen theoretical model with machined aluminum waste chips and alkali solutions up to 1M as a promoter, and to estimate overall reaction profit. In order to obtain results of better accuracy, we work with flat Al waste chips because a flat surface is preferable to maximally increase the time for created hydrogen bubbles to reach the critical gas pressure. At describing the reaction kinetics, flat shape allows using a planar one-dimensional shrinking core model instead of much complicated polydisperse spheric shrinking core model. We analyze the surface chemical reaction and mass transfer rate steps to obtain the first order rate constant for surface reaction and the diffusion coefficient of aqueous reactant in the byproduct layer, respectively. With our reactor we achieved H2 yield of 1145 mL per 1 g Al with 1M NaOH, which is 92% of the theoretical maximum. At estimation of the profit, we pay much attention to the loss of alkaline and find a crucial dependence on its price. Nevertheless, in terms of consumed and originated materials for sale, conversion of the aluminum waste material into green hydrogen by properly chosen reaction parameters has a positive profit even by consuming alkali of chemical grade.

Heat-treated aluminum-silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys due to their ability to remove the need for costly heat treatments. Since the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of a near eutectic Al-Ce alloy with additions of Ni and Mn. The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. SEM coupled with EDS and DSC techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase is present at higher cooling rates. At lower cooling rates, near the center of the casting, a proeutectic Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 at. % of Mn was dissolved in this proeutectic Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples' liquidus temperatures which is indicative of compositional variations. Inductively coupled plasma atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences to phase formation, which agreed with the SEM and DSC results. This experimentation provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

This paper aims to review the challenges, toxicity, and routes of synthesis and usage of silver nanoparticles in different applications but also highlighting their sustainability from both medical and environmental issues. Regarding their toxicity, it is known that silver nanoparticles can destroy over 650 microorganisms comparing with antibiotics. Supplementary, will be presented in a comparative manner some conventional synthesis routes (physical and chemical methods) and green synthesis routes using plant extracts. The approach using plant extracts have various advantages comparing with physical, chemical and microbial synthesis methods because there is no need to use chemicals, wasteful purifications and high energy requirements. The paper presents an overview on “green nanotechnology” focused on using either biological micro-organisms or plant extracts as an alternative to the classical chemical and physical methods. An important issue discussed in the paper is an overview of the synthesis routes of silver nanoparticles, some expected applications of silver based active agents and their toxicity and challenges that must be overcome. Also, it needs to focus our attention on the dismissal of silver nanoparticles into the environment and especially in water systems, fact which suggests that this issue must be fully understood and applied the law.

A method for accurately determining the chemical composition of deposits at the bottom of pores during the electrocoloring (e-coloring) of aluminum anodic oxide (AAO) layers in tin-based solutions is developed. The aluminum samples were AC e-colored after DC sulfuric anodization. Free-standing, tin e-colored aluminum oxide film was obtained by selective dissolution of the metallic aluminum from the AAO in copper chloride solution to access the deposit directly at the bottom of the pore. This allowed us to take XPS analysis directly from the deposits at pore bottoms without any interference from the base material or insulating barrier layer. The results revealed the presence of a mixture of tin oxide and metal in the deposits, which were richer in oxide content. Furthermore, a cyclic voltammetry experiment mimicking real polarization conditions during AC conditions was optimized and used to gain a deeper understanding of the electrochemical reactions that occur during AC electrocoloring. The comparison of CV results in tin-free and tin-containing electrolytes indicated that the tin deposited during a cathodic cycle is oxidized in the anodic cycle. The formation of tin based deposits radically changed the CV behavior. The XPS and cyclic voltammetry results consistently show that the deposits formed during e-coloring comprised a mixture of metallic and oxidic tin species richer in oxide content.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

Focused electron beam induced deposition is a versatile tool for the direct fabrication of complex-shaped nanostructures with unprecedented shape fidelity and resolution. While the technique is well-established for various materials, the direct electron beam writing of silver is still in its infancy. Here, five different silver carboxylates, three fluorinated: [Ag2(µ-O2CCF3)2], [Ag2(µ-O2CC2F5)2], [Ag2(µ-O2CC3F7)2] and two containing hydrogen: [Ag2(µ-O2CCMe2Et)2] and [Ag2(µ-O2CtBu)2] were examined and compared as potential precursors for focused electron beam induced deposition. All of the compounds show high sensitivity to electron dissociation and efficient dissociation of Ag-O bonds. The as-deposited materials showed high silver content from 42 at.% to above 70at.% and silver nano-crystal formation with impurities of carbon and fluorine incorporated between metal grains. A correlation of the number of carbon atoms in the precursor ligands and silver content of the deposited structures was found. The highest silver contents were achieved for compounds with the shortest CF chains. The deposited silver content depends on the balance of electron induced ligand co-deposition and thermal ligand desorption. Low electron flux is advantageous for high silver content. Our findings demonstrate that silver carboxylates constitute a promising group of precursors for focused electron beam nanoprinting of high silver content materials.

This paper presents a new method of preparing a coating on the Ti65 titanium alloy by a two-step procedure comprising hot-dipped aluminum and solid carburization. The effects of the carburization in the presence of NaCl deposit at 810oC have been systematically studied. In this article, the microstructure, morphology, phase composition of the coating, and the corrosion products were investigated by SEM, EDS, and X-ray diffraction. Results indicated that the corrosion resistance of hot dip aluminum/carburizing composite coating was not significantly enhanced by hot dip aluminum coating. This can be attributed to the formation of TiC and Ti3AlC after carburization, which promoted the formation of loose and unprotected TiO2 in the coating during molten salt corrosion. In addition, the oxidation of the carbon atom into CO2 /CO leaded to a high concentration of vacancy in the coating, creating channels for NaCl to penetrate the coating and accelerated the corrosion rate.

The analysis of high-temperature physicochemical properties of theK₃AlF₆-Na₃AlF₆-AlF₃ molten salt system is crucial for practical production of electrolytic aluminum. In this paper, the physicochemical properties of the K₃AlF₆-Na₃AlF₆-AlF₃ molten salt electrolyte system at 1173 K and standard atmospheric pressure were simulated using molecular dynamics calculations. The effects of Zr、B、C、W、Ti、Hf、Nb、and Ta on the radial distribution function, coordination number, viscosity and conductivity of the electrolyte system are discussed in detail. The simulation results show that the coordination number between Al-F and the conductivity is decreasing as the content of B²- increases. And the coordination number between Al-F and the viscosity is decreasing as the content of Zr⁴⁺ increases. With the addition of impurity elements such as C, W, Ti, Hf, Nb, and Ta, the data show that C has no significant effect on this electrolyte system, while the presence of W will decrease the coordination number between Al-F in the system. The presence of Ti, Hf, Nb, and Ta may intensify the decomposition reaction between one of the Al-F ligands, which increases the coordination number between Al-F and the number of ions in the electrolyte. This work provides theoretical support for the subsequent study of inert anodes containing Zr, B, Ti, Hf, Nb, and Ta.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

Light alloys machining is a widely implemented process that have usually used in presence of cutting fluids to reduce the wear impact and increase tool life. However, current environmental protection policies require their elimination in order to improve process sustainability. This fact forces to work under aggressive cutting conditions, producing adhesion wear that affects the integrity of the part surface. This study describes cutting tool wear mechanisms in machining of UNS A92024 samples under dry cutting conditions. EDS analysis showed the different composition of the adhered layers, while roughness was also positively affected by the change of the cutting geometry produced in the tool.

Molecular modeling studies were carried out at the DFT level of the adsorption of propane and propene on Ag surfaces as a model of the interaction of light hydrocarbons with Ag/ZrO2 catalysts for the catalytic combustion reaction. It was found that the most stable mode of adsorption of propene through its π system on Ag atom has energies consistent with chemisorption and generates an elongation of the C1=C2 bond, which would explain the increase in the activity of the catalysts as function of its metallic charge. The results obtained from the DFT calculations explain the different types of interaction between propene and propane with the metallic surface. The propene is chemisorbed on the Ag surface, distorting its bonds and generating its activation. This would imply that a higher metallic charge in the catalyst would increase the number of active sites in which this activation occurs, generating a higher activity. Besides, with the addition of O, the binding energy between the propene and the metal surface increased. On the other hand, the presence of a metallic surface is not enough for the activation of the propane molecule. This would explain why by increasing the amount of metal in the catalyst, the activity for the combustion of propane is practically not affected

Starch is a widespread natural polymer used in healthcare applications due to its low cost and antibacterial properties. The use of starch in its many forms and its sometimes combination with metallic nanoparticles have all contributed to the advancement of biomaterials. However, few studies have been conducted on biocomposites composed of jackfruit starch and silver nanopar-ticles (AgNPs). As a result, this research aims to study the physicochemical, morphological, and cytotoxic features of a Brazilian jackfruit (Artocarpus heterophyllus) starch-based scaffold loaded with AgNPs. Gelatinization and chemical reduction were used to synthesize the scaffold and AgNPs, respectively. X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), and Fourier transform infrared spectroscopy (FTIR) were utilized to explore the properties. The findings supported the development of anisotropic, stable, monodispersed AgNPs. The presence of AgNPs in the scaffold matrix was revealed by XRD and SEM-EDS. AgNPs were found to modify the crystallinity, roughness, and thermal stability of the scaffold while leaving its chemical and physical characteristics unchanged. Finally, the scaffolds did not show adverse effects on the L929 cells.

Hydrogel antibacterial agent is an ideal antibacterial material because of it could diffuses antibacterial molecules into the decayed area by providing a suitable microenvironment and the hydrogel acts as a protective barrier on the decay interface. The biocompatibility and biodegradation make the removal process easily which were widely used in medical fields. However, there have been few reports on its application for controlling postharvest diseases in fruit. In this study, the Chitosan-Ag (CS-Ag) complex hydrogels were prepared using the physical crosslinking method, which used for controlling postharvest diseases in grape. The prepared hydrogels were stable for a long period at room temperature. The structure and surface morphology of CS-Ag composite hydrogels were characterized by UV-Vis, FTIR, SEM, and XRD. The inhibitory effects of CS-Ag hydrogel on disease in grape caused by P. expansum, A. niger and B. cinerea were investigated both in vivo and in vitro. The remarkable antibacterial activity of CS-Ag hydrogels was mainly due to the synergistic antibacterial and antioxidant effects of CS and Ag. Preservation test showed that the CS-Ag hydrogel had positive fresh-keeping effect. This revealed CS-Ag hydrogels plays a critical role in controlling fungal disease in grape.

In this work, silver nanoparticles (AgNPs) were synthesized rapidly and eco-friendlily using the extract of Mulberry leaves and aqueous solution of silver nitrate without any toxic chemical [1,2]. The Mulberry leaves extract acts as both reducing agent and stabilizing agent. The UV-Vis spectrum shows peak at 430 nm. The TEM image of synthesized AgNPs sample shows spherical shaped particles whose size range from 15 to 20 nm. TEM image of nano silver solution sample synthesized by microwave assisted method shows nearly spherical particles with an average particle size of 10 nm. The absorption UV-vis spectrum of silver nanoparticles synthesized by microwave assisted method (AgNPsmw) shows a sharp absorption band around 415 nm. After two month storage of AgNPsmw, the absorption spectrum of AgNPsmw was taken again. The UV-Vis spectrum shows negligible peak changes of silver nanoparticles have occurred after two months of storage. The synthesized AgNPs material could be used as an antimicrobial, used in the field of textile and in wastewater treatment.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

Pure silver as well as silver compounds have been used as antiseptics for centuries. Nowadays, the most frequently applied form of silver is a nanoparticle form. Several studies demonstrate the ability of silver nanoparticles and silver salts to accumulate in the brain of laboratory ani-mals as well as the ability of silver nanoparticles to influence behavioral and cognitive functions of laboratory mammals. For the first time, the influence of a silver salt, in particular, silver citrate on the change dynamics of behavioral and cognitive functions of laboratory mice at the daily oral exposure during 30, 60, 120 and 180 days is investigated in the present research. We observed the anxiety increase after 30 days of the exposure as well as the ability of mice to adapt to the prolonged oral exposure of silver citrate manifested in the anxiety decrease, increase of locomotor activity and the tendency of long-term contextual memory improvement. Increase of locomotor activity and memory improvement might be associated with the sensitivity increase and regarded as compensatory mechanism to anxiety increase. The observed phenomenon is classified as a hormetic effect. A comparison with the analogous study implemented polyvi-nylpyrrolidone coated silver nanoparticles is carried out. It was concluded that the nanoform is more neurotoxic.

Silver in different forms is used for medical purposes from ancient times. It is not yet well known, which form of silver is more biocompatible and less toxic. Here we considered silver nanoparticles and silver citrate. Also, the relationships of neurotoxicity of silver compaunds with ageing factor is not yet described. To assess the role of nanoform in neurotoxicity of silver and role of ageing a long-term experiment was conducted. We had four control groups of intact mice and four experimental groups which were exposed to silver nanoparticles and silver citrate for two months. Four groups of mice were introduced into the experiment since the age of five months to assess ageing factors. It was shown that the nanoform does play a certain role in neurotoxicity of silver. Silver citrate seems to be a more preferable silver compound. Ageing can be regarded as a positive factor that neutralizes toxic action of silver compounds. It may be due to the development of physiological/cognitive functions with the age as well as adaptation to unnatural content in the individual cages that is definitely stressful for mice.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

This study investigated the relationship between aluminum adjuvant vaccines and the prevalence of 4 childhood diseases (Autism, Allergies, Asthma, ADD/ADHD) using data from the 2020-2021 National Survey of Children's Health (NSCH) [1] and the Centers for Disease Control National Immunization Survey (CDC NIS) [2]. The study found an association with aluminum adjuvant dosage and the prevalence of each disease studied (Autism, Allergies, Asthma, ADD/ADHD) through a weighted regression analysis of disease prevalence against the summed likelihood of aluminum adjuvant vaccine uptake.

Although 7055 aluminum alloy is a deformed aluminum alloy and will show excellent mechanical properties after recrystallization after large deformation, it is a method to enrich its application range if rare earth is added and the rare earth phase dispersion is promoted by heat treatment. This article used optical microscopy, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), micro Vickers hardness and room temperature stretching methods to study the as-cast 7055-xEr (x=0wt.%, 0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.%) aluminum alloy after being subjected to 460 oC×3h homogenization and 410 oC×1h solid solution+150 oC×12h aging treatment the changes in microstructure and properties. The results indicated that: when 0.2wt.%Er was added to 7055 aluminum alloy after solution at 410 oC×1h and aging at 150 oC×12h, the dendrite structure was significantly reduced, the grain thinning was obvious and the distribution was uniform, Al8Cu4Er phase appeared in the lamellar eutectic η-Mg(Zn,Al,Cu)2 structure at grain boundaries, and the hardness reached 168.8HV. The yield strength, tensile strength and elongation were 542.12Mpa, 577.67MPa and 8.36%, respectively.

A technology for obtaining nanosized aluminum nitride powder by plasma-chemical synthesis is presented. Nitrogen gas (N2), melamine (C3H6N6) and ammonia (NH3) were used as a source of nitrogen. Aluminum powder of different fractions was used as a source of aluminum. The influence of the nitrogen source, the height of the injector, and the input power of the plasma equipment on the synthesized aluminum nitride powder is shown. The resulting aluminum nitride powder has a size d90=60 nm. The parameters of aluminum nitride synthesis did not in any way affect the granulometric composition of the synthesized powder materials. It was found that, due to the high binding energy, the nitrogen molecule (N2) reacts poorly with aluminum powder particles, as a result a mixture of nitrogen and ammonia gases was used in a ratio of 70/30 (mol.%) for aluminum nitride synthesis.

In this study, a summary of the processes performed on the SPL for recycling, reduction in toxicity and treatment were examined on an industrial and laboratory scale. In writing this research, an attempt has been made to address the useful processes that have taken place in this field. Spent pot lining or SPL is a type of solid waste that is produced in the aluminum production process. After 3 to 8 years, the cathode blocks become problematic and can no longer be used, and need to be replaced due to adverse effects on cell function. SPL is known to be a hazardous waste to nature due to its fluoride and cyanide content. Research has shown that SPL ingredients have destructive and very dangerous effects on human DNA, which is why they are so important to maintain and recycle.

Sugarcane is an important sugar-source crop. As any other plant, it can be exposed to several abiotic stress conditions. Though some metals contribute to critical physiological processes in plants, the presence of aluminum ions (Al3+) can be very toxic. In order to develop plants that flourish in acidic soils, it is critical to gain insights into the molecular mechanisms of sugarcane response to aluminum stress. To determine the genes involved in sugarcane response to aluminum stress we generated 372 million paired-end RNA sequencing reads, from roots of CTC-2 and RB855453 two contrasting cultivars. Data normalization resulted in 162,161 contigs and 97,335 trinity genes. After the read cutoff, the differentially expressed genes were 4,858 in CTC-2 and 1,307 in the RB855453, Treatment Vs Control, respectively. The differentially expressed genes were annotated into 34 functional categories. The majority of the genes were upregulated in the CTC-2 (tolerant cultivar) and down regulated in RB855453 (sensitive cultivar). Here, we present the first root-transcriptome of sugarcane under aluminum stress. The results and conclusions of this study provide a valuable resource for future genetic and genomic studies in sugarcane. This transcriptome analysis points out that sugarcane tolerance to aluminum may be explained by an efficient detoxification mechanism combined with the lateral root formation and activation of redox enzymes. Following our results, we present here, a hypothetical model for the aluminum tolerance in CTC-2 cultivar.

Strain induced melt activation process (SIMA) creates a globular microstructure which improves the hardness and ultimate tensile stress (UTS) of 7075 aluminum alloys. But, at the grain boundaries of SIMA processed 7075 aluminum alloy, presence of continuous and brittle intermetallic compounds and the eutectic structure result in decreasing mechanical properties, such as elongation, formability and etc. Hence, in order to improve microstructure and formability of 7075 aluminum alloy respect to SIMA process, a new process was done that is called two-step strain induced melt activation (TSSIMA). This process, which has been mentioned in the experimental procedure section, both organized globular structure and significantly modified the microstructure of the alloy compared to that of the SIMA method. It promoted discontinuity and more homogeneity in distribution of the precipitates and, approximately removed the eutectic mixture. Performing the rolling process on the alloy also revealed that it is more effective in formability enhancement in comparison with SIMA process. Also, it increased the hardness of 7075 aluminum alloy respect to that of SIMA process.

Staphylococcus pseudintermedius (SP) is an emergent zoonotic agent associated with multidrug resistance (MDR). This work aimed to describe the antibacterial activity of four essential oils (EOs) and silver nanoparticles (AgNPs) against SP. Fifteen SP strains were tested. The four EOs, namely Rosmarinus officinalis (RO), Juniperus communis (GI), Citrus sinensis (AR) and Abies alba (AB), and AgNPs were used alone and in combination to determine the Minimum Inhibitory Concentration (MIC) and Minimum Bactericidal Concentration (MBC) against SP. All strains presented MDR and methicillin resistance. Among the antibiotic cohort, only rifampicin, doxycycline and amikacin were effective. When EOs were tested alone, AB showed the lowest MIC followed by GI, RO and AR (0.23%±0.3; 0.5%±0.51; 0.79%±0.39; 0.93%±0.63). MBC was increased with the following order: AB, GI, AR and RO (3.56%±4.87; 4.93%±6.27; 8.53%±7.2; 10.34%±5.31). MIC and MBC values for AgNPs were 10.74 mg/L±4.23; 261.05 mg/L±172.74. In combination, the MIC and MBC values were lower for all compounds. In conclusion, EOs and AgNPs could be considered as promising antibacterial alternatives to antibiotics.

This study was conducted to recover valuable metals (silicon and silver) using acid leaching and substitution reactions with copper powder from the pulverized solar cell separated from the PV ribbon. Leaching experiments were conducted according to nitric acid concentration by molar solution as 1M, 2M, and 3M using an ultrasonic cleaner at a reaction temperature of 60 °C for the leaching times of 30 to 120 minutes. Si phases were detected at all leaching reaction times, it was confirmed that the aluminium was removed effectively if the nitric acid leaching time was more than 30 minutes, and silicon with a purity above 99% could be recovered. The silver was precipitated by adding copper, which has greater reducibility than Cu, Al, Si, Pb, and Sn. When the addition of copper powder was 0.75 and 1.0 g, precipitate was produced 0.23 and 0.55 g, respectively. The optimal condition for the recovery of silver by the addition of copper powder was 1 g, where is recovery rate reached 93.3%.

Introduction: Silver nanoparticles have been extensively investigated in dental and orthopedic materials. However, the impregnation of bone graft with silver nanoparticles has been poorly investigated. Objectives: The aim of this study was to evaluate the in vitro antibiofilm activity of a bovine bone impregnated with silver nanoparticles. Methods: Bone scaffolds from cancellous bovine femur were used for the tests and impregnated with silver nanoparticles (50nm) by physical adsorption. Silver nitrate minimal inhibitory and bactericidal concentration were performed Staphylococcus aureus, Pseudomonas aeruginosa, Candida albicans, Enterococcus faecalis, Acinetobacter baumannii, and Escherichia coli. Disc diffusion tests for silver nanoparticles susceptibility and quantification of biofilm production on plate and bone with sessile cell count were also performed. Results: All pathogens were susceptible to silver with low minimal inhibitory concentration (0.25 – 4 mg/L). The scaffold impregnated with silver nanoparticles presented a significant reduction in the biofilm cells for all microorganisms with a reduction of more than 3 logs in colony forming units count. Conclusion: Bone scaffolds impregnated with silver nanoparticles can significantly reduce biofilm, and it can be a strategical material to be used as an implant for different approaches.

Abstract: Given the increasing resistance of some bacterial strains to many common antibiotics used in the local market, the current study aimed to produce nanoscale particles capable of combating pathogenic bacteria that have developed resistance to current antibiotics. In this research, an ex-perimental study was conducted to produce nanoscale particles using the single-celled blue-green algae Synechococcus sp., which was isolated from a local environment in the Arab Republic of Egypt, specifically from a soil sample in Beni-Suef City. The aim of the study was to generate silver NPs employing different biological approaches, encompassing the direct strain powder technique, ethanol extract pellet technique, and ethanol extract technique. These synthesized nanoparticles displayed different shapes, including cubic, spherical, pellet-like, and rod-shaped particles. They were characterized by bio-functional groups containing Ag+ ions, which were detected using FT-IR, Zeta sizer, and Zeta potential measurements. High-resolution SEM imaging unveiled the mor-phological features of Silver NPs with biologically formed protective layers, spanning sizes from 20 to 430 nm for individual particles. The study evaluated the antibacterial efficiency against both G+ve and G-ve bacteria. The ethanolic extract technique exhibited the largest inhibition zone (24 mm) against G+ve bacteria, particularly Staphy. aureus. Furthermore, it was observed that the larger particles produced using the powder and pellet techniques were less effective antibacterial agents. In conclusion, this investigation emphasizes the potential of cyanobacteria-based synthesis of silver nanoparticles as a promising approach for producing innovative antimicrobial agents.

Introduction: Infections associated with medical implants pose significant challenges to healthcare, demanding the development of new effective antimicrobial strategies. This study focuses on the creation of a novel biological membrane with enhanced antimicrobial properties by with the incorporation of either vancomycin or silver nanoparticles. Methods: Pericardium samples were impregnated with either silver nanoparticles (AgNPs) or vancomycin (VAN). The antimicrobial activity of the membranes was assessed through qualitative microbiological analysis, biofilm production and animal in vivo model of infection. Histological analysis was performed on the pericardium samples, and quantitative microbiological analysis was conducted on the tissue from the animal model and biocompatibility evaluation. Statistical analyses were carried out using appropriate tests. Results: Microbiological tests confirmed both VAN and AgNP showed inhibition halos against bacteria. Histological analysis indicated minimal inflammatory response and bacterial presence in VAN and AgNP groups compared to the control group revealed reduced bacterial presence. Biomechanical testing showed that polypropylene had the lowest tensile strength, while AgNP-impregnated pericardium exhibited lower resistance than VAN-impregnated and control pericardium. Conclusion: Lyophilized and decellularized bovine pericardium as a substrate, combined with the incorporation of vancomycin or silver nanoparticles, provides a versatile platform for combating infections associated with medical implants.

The invention of nanoscience not only brings a revolutionary change in the field of science but also changed the direction of research. Today the whole world is under the trigger of nano and nanoparticles have multidimensional applications in every aspect of life including environmental point of view. Till today a plethora of nanoparticles have been synthesized and have also been applied for multiple purposes and hence grabbed the attention of researchers all over the world. Among the bunch of NPs discovered to date, we have a particular interest in silver nanoparticles (AgNPs) because of their cost-effectiveness and huge abundance in the earth’s crust. With respect to every passing day, due to various kinds of anthropological activities, the quality of the environment such as air, water and soil is depleting which ultimately hampers the human civilization. To encompass the growing environmental issues, many techniques have been adopted. Among the many strategies, tackling the current issues regarding environment through nanoscience is highly worthy as because of its cost-effectiveness, less time consuming and easy handling process. This article reviews the potential of nanoparticles, particularly silver nanoparticles, for a wide range of environmental applications, such as soil, air, and water remediation.

One of the largest in the archipelago silver-copper mineralisation at Mount Sigurdf′ellet in West Spitsbergen Island was found in 1990 by Russian geologists. Firstly genesis was caused exclusively with hydrothermal ore migration of a substance from the enclosing sandstone and siltstone of the Devonian age. But subsequent work on the ore and nearest rocks of the basement gave a new factual material on the geochemical characteristics of potential sources of metals and found new for this mineral occurrence - gold mineralization. Similarity of geochemical associations of Sigurd ore occurrence with nearby upper Proterozoic marble as the first likely source of ore substance and the second - caused by carbonate-containing streaks in Low Devonian sediments. Ore-formation, probably due to repeated hydrothermal processes and was completed in a period of tectono-magmatic activity in Jurassic-Cretaceous time.

There is much interest in effective copper chelators to correct copper dyshomeostasis in neurodegenerative and oncological diseases. In this study, a recombinant fusion protein for expression in E. coli cells was constructed from glutathione-S-transferase (GST) and the N-terminal domain (ectodomain) of human high affinity copper transporter CTR1 (hNdCTR1), which has three metal-bound motifs. Several biological properties of the GST-hNdCTR1 fusion protein were assessed. It was demonstrated that in cells, the protein was prone to oligomerization, formed inclusion bodies and displayed no toxicity. Treatment of E. coli cells with copper and silver ions reduced cell viability in a dose- and time-dependent manner. Cells expressing GST-hNdCTR1 protein demonstrated resistance to the metal treatments. These cells accumulated silver ions and formed nanoparticles that contained AgCl and Ag0. In this bacterial population, filamentous bacteria with length about 10 μm were often observed. The possibility for the fusion protein carrying extracellular metal binding motifs to integrate into the cell’s copper metabolism and its chelating properties are discussed.

Aluminum, a contentious trace element found in the environment, has been demonstrated to have harmful effects on both humans and animals. In contrast, Sempervivum tectorum, an evergreen plant, has been found to offer numerous beneficial effects for both humans and animals. Therefore, this study aims to assess the protective effect of S. tectorum on certain reproductive biomarkers in male rats exposed to aluminum. Thirty-five Wistar rats were randomly divided into five groups: NTC (no-treatment control) received distilled water; NC (negative control) received drinking water containing 1 mg/L aluminum sulfate (AS); E1 received 1 mg/L AS along with an 8% S. tectorum extract; PC (positive control) received only 8% S. tectorum extract; E2 received 1 mg/L AS for three months followed by 8% extract for one month. The study analyzed testosterone, LH, FSH, body weight, and the histological structure of the testis, epididymis, and prostate, as well as the levels of zinc, manganese, copper, and iron in these organs. Significant decreases in body weight, testis, and epididymis size were observed in the aluminum-exposed groups compared to the control, whereas these decreases were not significant in the S. tectorum-treated groups compared to the control. Aluminum exposure led to significant decreases in testosterone and LH levels, with FSH levels showing a non-significant decrease in males, which were mitigated significantly by the administration of the plant extract. Histological analysis revealed alterations in the testis, epididymis, and prostate of the AS-exposed groups, including necrosis of seminiferous tubule epithelium and Leydig cells in the testis, and basal epithelial necrosis in the epididymis and prostate. Aluminum levels increased in all organs studied, while levels of zinc, copper, iron, and manganese decreased, showing a negative and significant correlation with aluminum levels. The aqueous extract of S. tectorum demonstrated a protective effect on certain studied biomarkers in male rats affected by aluminum exposure.

Hypoeutectic Al-Si-Cu-Mg alloys are promising candidates for use in automobile parts. Therefore, various attempts have been made to develop alternative casting technologies to improve the mechanical properties of cast alloys. In this study, the effects of modification with different levels of strontium (Sr) on primary and eutectic silicon (Si) in hypoeutectic Al-Si-Cu-Mg alloys were investigated. Using a gravity cast process, the Sr-modified samples were prepared from melts with four levels (100, 200, 300, and 400 ppm) of Sr. In addition, the wear properties of the cast samples were studied using a block-on-ring wear-testing machine. The sizes of the primary Si phases increased with increasing Sr content in the alloys. Moreover, more finely dispersed eutectic Si was observed with higher Sr content. In frictional wear tests, the specific wear rates of the test specimens decreased as the Sr content increased from 200 to 400 ppm. Coarse Si phases are considered to act as solid lubricants in the contact region during sliding.

Modified aluminum slag (MAS) was applied as an adsorbent for Congo red (CR) prepared by the hydrothermal treatment of Ca (OH) 2. At 25 ℃, with a MAS dosage of 0.3g, initial CR concentration of 100 mg/L and initial pH=5, and the adsorption time was 40 min, the CR removal efficiency was 98.41%. The adsorption trend of CR conformed to the second-order kinetics, and the adsorption isotherm follows the Freundlich isotherm model. Compared with RAS, MAS has a larger pore volume and specific surface area. The mechanism of action of MAS on CR was the interaction between membrane diffusion and internal diffusion, and the adsorption rate during the membrane diffusion was the fastest.

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

Aluminum is a strategic mineral resource, and China’s aluminum production and consumption is fairly large. However, its supply guarantee is uncertain because of a high dependency on external raw materials. This uncertainty may expand, so finding a way to reduce the uncertainty of aluminum resource supply is especially important. This paper applies the SFA method to analyze the aluminum flows in mainland China from 1996 to 2014, and establishes a supply structure model to measure its supply guarantee degree. The results claim that: (1) China’s aluminum production can satisfy demand and even create a surplus; (2) Domestic self-productive primary and secondary aluminum increased at an annual rate of 12% and 24%; (3) The proportion of self-productive secondary aluminum in the supply structure increased from 7.7% in 1996 to 12.8% in 2014, while that of primary aluminum decreased from 79.6% to 42.8%; (4) The total supply guarantee degree decreased from 87.3% to 55.6% in this period. These results provide a feasible way to solve this plight: the proportion of secondary aluminum in the supply structure should be enhanced, and an efficient aluminum resource recycling system needs to be established as soon as possible to ensure its sustainable supply.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

Staphylococcus aureus is a causative agent of nosocomial infections and its antibiotic-resistant strains are concerning. Solutions are being explored to improve the treatment of these infections, including repositioning drugs such as statins and using nanoparticles with antimicrobial properties. This study aimed to evaluate the antimicrobial effects of simvastatin (SIM) and biologically synthesized silver nanoparticles (bio-AgNPs) in isolate form and in combination by assays of minimum inhibitory concentration (MIC), an in vitro biofilm model, and the association of antimicrobials against clinical strains of S. aureus. Bio-AgNPs showed a 53.8 ± 1.23-nm mean diameter and standard deviation, a 0.23 polydispersity index, and a −25.66 ± 2.19-mV mean potential and standard deviation. Transmission electron microscopy confirmed the formation of nanoparticles and the presence of Ag0 and AgCl. S. aureus strains were sensitive to bio-AgNPs and SIM, showing 31.88-187.5 and 74.66-149.32 μM concentrations, respectively. Our association assay showed 2.0 fractional inhibitory concentration indices (i.e., indifferent for clinical strains) and 0.32 values for the standard ATCC 29213 strain (synergy). Our biofilm inhibition assays with isolated SIM and bio-AgNPs showed decreased biofilm formation from 4× to ⅛ MICs, showing no synergism in association. These findings evince that simvastatin and bio-AgNPs at subinhibitory concentrations can serve as antimicrobial agents against S. aureus biofilm.

Recent researches indicated that metal nanoparticles which have the unique optical properties can be used to enhance the spectral response of the photovoltaic modules. Since most of the nanoparticles have enhancement effects in a specific wavelength range, improving the spectral response of the photovoltaic modules in a broadband range is crucial for their applications in imaging, energy harvesting, and optical communication. In this study, flower-like silver particles are applied to achieve the enhancement effects in a broadband range. The optical absorption of photovoltaic modules is improved in a broad wavelength range of 400~2000 nm by immobilizing flower-like silver particles onto an amorphous Si p-i-n structure, and the peak responsivity of the spectral response is enhanced by about 10 times. Theoretical investigation further elaborates that the enhancement originates from the near-field effects of silver particles due to the interaction of different parts of the flower-like silver particles. Through these studies, we demonstrate that, utilizing the subwavelength silver particles with roughness surface can achieve the spectral response of the photovoltaic modules enhanced in broadband range, which can improve the utilization efficiency of optical energy for the applications of sensing, imaging, optical communication, and energy harvesting.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

Introduction: Among the many factors that may limit effective wound healing in patients with chronic ulcers, bacterial infection and poor cell recruitment are primary causes that contribute to prolonged healing. Thus, a novel strategy that aims to prevent bacterial infection within the wound, while at the same time providing structural scaffolding that promotes endogenous tissue repair, would be of great interest. Here, we developed a thermo-sensitive silver nanoparticle hydrogel composite as an antibacterial nutritional scaffold for the wound that contains all nutrients required for cell growth while preventing bacterial infection with the ability to fill up all the cavities and void areas in wounds regardless of their geometry. Methods: Silver nanoparticles (AgNPs) were synthesized by chemical reduction. After characterization, silver hydrogel nanocomposite was developed by reconstitution of collagen-based hydrogel powder in a nanoparticle suspension of varying AgNPs concentrations (200, 400, and 600 ppm). The antibacterial activity of the formulations was examined in vitro and in vivo in subcutaneous implant infected model. The wound healing efficacy of the hydrogel nanocomposite was also evaluated using a splinted wound model in rats through comparison of clinical wound measurements and histological assessments. Cytocompatibility assay and biochemical analysis of blood at the end of in vivo wound healing study were performed to evaluate the safety of formulations. Results: The synthesized nanoparticles were spherical and stable. While hydrogel alone did not show any bacterial reduction in vitro, the inhibition of bacterial growth was significant in all silver hydrogel nanocomposites compared to controls (p <0.05) and was dose-dependent, with maximum reduction observed in the 600 ppm group (4.56±0.26 LOG CFU/mL, P<0.001). All concentrations of AgNPs hydrogel composites showed significant antibacterial activity in vivo as well (P<0.0001). Treatment of splinted wounds with AgNPs hydrogel composite resulted in faster wound closure and accelerated wound re-epithelialization. The formulations were non-cytotoxic and did not differ significantly in hematological and biochemical factors from the control group in in vivo study. Conclusions: By presenting promising antibacterial and wound healing activity, silver hydrogel nanocomposite offers a safe therapeutic option that can be used as a functional scaffold for an acceleration of wound healing.

Long-term changes in nanoparticles of copper-silver bimetallic systems on natural clinoptilolite obtained by ion exchange of Cu2+ and Ag+, and then reduced at different temperatures, have been studied. Even after storage under ambient conditions, XRD and UV-Vis diffuse reflectance spectra indicate the presence of nanospecies of reduced copper and silver. Scanning Electron Microscopy of aged bimetallic samples, reduced at the highest temperature (450oC) and the primary samples for their preparation, also aged, showed the presence of silver nanoparticles with a size of about 100 nm. They are formed in the initial ion-exchanged sample (without reduction) due to the degradation of Ag+ ions. The nanoparticles in the reduced sample are larger; in both samples they are evenly distributed over the surface. The presence of silver affects the stability and the mechanism of decomposition/oxidation of reduced copper nanospecies, and this stability is higher in bimetallic systems. The decomposition pattern of recently reduced species includes the formation of smaller nanoparticles and few-atomic clusters. This can occur, preceding the complete oxidation of Cu to ions. Quasi-colloidal silver, which is present in fresh bimetallic samples reduced at lower temperatures, transforms after aging into Ag8 clusters, which indicates the stability of these nanospecies on natural clinoptilolite.

Reaction of 2-mercapto-3-phenylquinazolin-4(3H)-one (MPQ) with both 4-vinyl benzyl chloride and allyl bromide furnished the reactive heterocyclic monomers 3-phenyl-2-((4-vinylbenzyl) thio) quinazolin-4(3H)-one (PVTQ) and 2-(allylthio)-3-phenylquinazolin-4(3H)-one (APQ), respectively. Copolymerization of PVTQ monomer with styrene and methyl methacrylate in the presence of 2,2′-azobisisobutyronitrile (AIBN) afforded the copolymers PS-co-PPVTQ and PMMA-co-PPVTQ, respectively. Similarly, copolymerization of monomer APQ with styrene and methyl methacrylate (MMA) afforded the copolymers PS-co-PAPQ and PMMA-co-PAPQ, respectively. The resulted copolymers were characterized by using FT-IR, 1H-NMR and GPC techniques. Silver nanocomposites of PS, PMMA, PS-co-PPVTQ, PMMA-co-PPVTQ, PS-co-PAPQ and PMMA-co-PAPQ were synthesized by the addition of silver nitrate into the polymer solution. The reduction of silver ions into silver nanoparticles was performed in DMF and water. Thermogravimetric (TGA) analysis was used to determine the thermal stability of the copolymers and their silver nanocomposites. The X-ray diffraction (XRD) analysis indicated the amorphous structures of the co-polymers and confirmed the formation of silver nanoparticles. The antitumor and antibacterial activities were screened for the copolymers and enhanced by the formation of their silver nanocomposites. In vivo antitumor activity in Ehrlich Ascitic Carcinoma (EAC) mice model showed that PS-co-PPVTQ/Ag NPs, PMMA-co-PPVTQ/Ag NPs, and PMMA-co-PAPQ/Ag NPs displayed promising inhibitory effects against EAC and induce apoptosis against MCF-7 cells.

Clinical resistance to amikacin and other aminoglycosides is usually due to enzymatic acetylation of the antimicrobial molecule. A ubiquitous resistance enzyme among Gram-negatives is the aminoglycoside 6'-N-acetyltransferase type Ib [AAC(6')-Ib], which catalyzes acetylation using acetyl-CoA as donor substrate. Therapies that combine the antibiotic and an inhibitor of the inactivation reaction could be an alternative to treat infections caused by resistant bacteria. We had previously observed that metal ions such as Zn2+ or Cu2+ in complex with ionophores interfere with the AAC(6')-Ib-mediated inactivation of aminoglycosides and reduced resistance to susceptibility levels. Ag1+ recently attracted attention as a potentiator of aminoglycosides' action by mechanisms still in discussion. We found that silver acetate is also a robust inhibitor of the enzymatic acetylation mediated by AAC(6')-Ib in vitro. This action seems to be independent of other mechanisms, like increased production of reactive oxygen species and enhanced membrane permeability, proposed to explain the potentiation of the antibiotic effect by silver ions. The addition of this compound to aac(6')-Ib harboring Acinetobacter baumannii and Escherichia coli cultures resulted in a dramatic reduction of the resistance levels. Time-kill assays showed that the combination of silver acetate and amikacin was bactericidal and exhibited low cytotoxicity to HEK293 cells.

The aim of the study was to analyze the in ovo injection of chemically and biologically synthesized silver nano-particles (Ag NPs) using Brassica oleracea L. var capitate f. Rubra, (BOL) conjugation with L-Arginine (L-Arg) on the immune, muscle growth, survivability and hatchability of the broiler chickens. L-Arg (100 μg) conjugated with 1000 µg of Ag NPs synthesized by (BOL)-extract and L-Arg (100 μg) conjugated with 100 µg of Ag NPs chemically synthesized were injected into fertile eggs at 8d, 14d and 18d of incubation. Living embryo and hatched chicks were calculated. Survivability and hatchability were not affected by the injected dose of L-Arg (100 μg) with 1000 µg (BOL-Ag NPs) and L-Arg (100 μg) with 100 µg (C-Ag NPs) but it significantly improved when the eggs were injected on day 14 of incubation compared with those injected on days 8 or 18. Moreover, the protein expression of muscle development markers such as myogenin and myoD were significantly up-related in 14 d of incubation whereas the heat shock proteins (HSPs) such as HSP-60 and HSP-70 were significantly up-regulated in 18 d incubation. In addition, the in ovo injection on 18 d significantly increased the serum glutamate oxaloacetate transaminase (SGOT) and serum glutamate pyruvate transaminase (SGPT) as well the immunoglobulin (IgM) levels were increased in 14d incubation period in serum at the same concentration.

Betadine (Providone-Iodine) solution is a topically applied antiseptic, which has been used for wound care and surgery for decades for the prevention and treatment of skin and wound infections. However, several studies have documented the ineffectiveness of Betadine solution. Other topical antimicrobial dressings, including those that contain silver, have been used in the management of infected wounds. The present study was undertaken to determine if the combination of 5% Betadine solutions and silver colloidal gel (Ag-gel), is more effective than the individual materials in inhibiting the growth of both Gram negative and Gram positive bacteria. These determinations were carried out by both the colony forming unit (CFU) assay, and confocal laser scanning microscopy (CLSM). Ag-gel showed complete inhibition on all the bacteria, except Klebsiella pneumoniae CI strain while 5% Betadine concentrations did not completely kill any of the tested bacteria. However, K. pneumoniae was completely eliminated in the presence of the combination of 5% Betadine solution plus Ag-gel. Confocal laser microscopy confirmed the CFU results. Thus this study demonstrated that while the individual treatments are not effective in killing all the bacteria tested, the combination of 5% Betadine solution and Ag-gel completely kill all bacteria tested, including K. penumoniae CI.

The aim of the study was to analyze the in ovo injection of chemically and biologically synthesized silver nano-particles (Ag NPs) using Brassica oleracea L. var capitate f. Rubra, (BOL) conjugation with L-Arginine (L-Arg) on the immune, muscle growth, survivability and hatchability of the broiler chickens. L-Arg (100 μg) with 1000 µg (BOL-Ag NPs) and L-Arg (100 μg) with 100 µg (C-Ag NPs) were injected into fertile eggs at 8, 14 and 18 of incubation. Survival and hatched chicks were calculated. Survivability and hatchability were unaffected by the injected dose of L-Arg (100 μg) with 1000 µg (BOL-Ag NPs) and L-Arg (100 μg) with 100 µg (C-Ag NPs) but it significantly improved when the eggs were injected on day 14 of incubation compared with those injected on days 8 or 18. Moreover, the protein expression of muscle development markers such as myogenin and myoD were significantly up-related in 14 d incubation whereas the heat shock proteins (HSPs) such as HSP-60 and HSP-70 were significantly up-regulated in 18 d incubation. In addition, the in ovo injection on 18 d significantly increased the serum glutamate oxaloacetate transaminase (SGOT) and serum glutamate pyruvate transaminase (SGPT) as well the immunoglobulin (IgM) levels were increased in 14-day incubation period in serum at the same concentration. Collectively, these results indicate that injecting L-Arg (100 μg) with 1000 µg of BOL-Ag NPs or L-Arg (100 μg) with 100 µg of C-Ag NPs to eggs at day 14 after incubation could improve their hatchability, survival rate, and muscle growth marker.

An array of Ag nanowires has been prepared from a facile, templated approach on Cu(BTC) (1,3,5-benzenetricarboxylic acid) metal organic framework (MOF) micropillars. The Ag-deposited scaffolding material may be used to prepare electronic or optoelectronic devices for various applications.

Background. Nanotechnology is promising field for generating new applications. A green synthesis of nanoparticles through biological methods using plant extract have a reliable and ecofriendly approach to improve our global environment. Methods. Silver nanoparticles (AgNPs) were synthesized using aqueous extract of Anagalis arvensis L and silver nitrate and were physicochemically characterized. Results. The stability of AgNPs toward acidity, alkalinity, salinity and temperature showed that they remained stable at room temperature for more than two months. The SEM and TEM analysis of the AgNPs showed that they have a uniform spherical shape with an average size in the range of 40–78 nm. Further 1-Dibhenyl-2-Picrylhydrazl radical in Anagalis arvensis L.mediated AgNPs showed a maximum activity of 98% at concentration of 200μg/mL. Hydrogen peroxide scavenging assay in Anagalis arvensis L. mediated AgNPs showed a maximum activity of 85% at concentration of 200μg/mL. Reducing power of Anagalis arvensis L.Ag NPs exhibited a higher activity of 330 μg/mL at concentration of 200 μg/mL. These NPs have cytotoxic effects against brine shrimp (Artemia salina) nauplii with a value of 53% LD 178.04μg/mL. Conclusion. The AgNPs synthesized using Anagalis arvensis L. extract demonstrate a broad range of applications.

Many wounds are unresponsive to current available treatment techniques and therefore there is an immense need to explore suitable materials including biomaterials, which are being considered as the crucial factor to accelerate the healing cascade. In this study, we fabricated polyhydroxyalkanoate based antibacterial mats via electrospun technique. One-pot green synthesized graphene decorated silver nanoparticles (GAg) were incorporated into the fibres of poly-3 hydroxybutarate-co-12 mol% hydroxyhexanoate (P3HB-co-12mol% HHx), a co-polymer of polyhydroxyalkanoate (PHA) family which is highly biocompatible, biodegradable and flexible in nature. The synthesised PHA/GAg biomaterial was characterized by field emission scanning electron microscopy (FESEM), elemental mapping, thermogravimetric analysis (TGA), UV-visible spectroscopy (UV-vis) and Fourier transform infrared spectroscopy (FTIR). In-vitro antibacterial analysis were performed to investigate the efficacy of PHA/GAg against gram positive Staphylococcus aureus (S.aureus) strain 12600 ATCC and gram negative Escherichia coli (E.coli) strain 8739 ATCC. The results indicated that the PHA/GAg demonstrated significant reduction of Staphylococcus aureus (S.aureus strain 12600 ATCC) and Escherichia coli (E.coli strain 8739 ATCC) as compared to bare PHA or PHA-rGO in 2 hours of time. The P value (P< 0.05) was obtained by using 2 sample T-test distribution.

Metallic elements of higher economic value occurring in the mineralogy of Zimapán are Pb, Zn, Cu and Fe, said elements are sold as concentrates, which, even after processing, generally include significant concentrations of Mo, Cd, Sb, Ag and As that could recover through different leaching methods. In this work the influence of temperature was studied in the complexation of silver in the S₂O₃^2--O₂ system. Chemical and mineralogical characterization of concentrated Zn from the state of Hidalgo confirmed the presence of the silver contained in a sulfide of silver arsenic (AgAsS₂) through the techniques of Atomic Absorption Spectrophotometry (AAS), X-Ray Diffraction (XRD) and Scanning Electron Microscopy-Energy-Dispersive X-Ray Spectroscopy (SEM-EDS). The mineralogical species identified allowed the construction mineralogical species Pourbaix diagrams in the range of 298 K to 333 K, through which the Eh-pH conditions to obtain silver in solution were determined. The formation of Ag(S₂O₃)₂^3- complex was confirmed by characterizing liquors leached using the technique Infrared Spectroscopy Fourier Transform (FTIR).

Additive Friction Extrusion Deposition (AFED) is a recently developed additive manufacturing technique that promises high deposition rates at low forces. Due to the novelty of the process, the underlying phenomena and their interactions are not fully understood, and in particular the processing strategy and tool design are still in their infancy. This work contributes to the state of the art of AFED through a comprehensive analysis of its working principles and an experimental program including a representative sample component. The working principle and process mechanics of AFED are broken down into their individual components. Forces, their origins and effects on the process are described, and measures of process efficiency and theoretical minimum energy consumption are derived. Three geometrical features of the extrusion die are identified as most relevant to the active material flow, process forces and deposition quality: the topography of the inner and outer circular surfaces and the geometry of its extrusion channels. Based on this, the experimental program investigates seven different tool designs in terms of efficiency, force reduction and throughput. The experiments using AA 6061-T6 as feedstock show that AFED is capable of both high material throughput (close to 550 mm³/s) and reduced substrate forces: For example, the forces for a run at 100 mm³/s remained continuously below 500 N, and for a run at 400 mm³/s below 3500 N. Material flow and microstructure of the AFED are assessed from the macrosections. Significant differences are found between the advancing and retracting sides for both process effects and material flow. Banded structures show strong similarities to other solid state processes. The fabrication of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical testing, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, in the microstructure show strong similarities to other solid-state processes. The manufacturing of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical tests, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, while in the horizontal direction of the structure mechanical properties corresponding to a T4 temper have been achieved.

This study aims to investigate a friction stir welded joint between steel and aluminum alloy. Friction stir welding is nowadays one of the most interesting joining technique due to the possibility to connect materials and thicknesses that are difficult or impossible to weld with traditional techniques. The main advantage is that Materials are not affected by thermal cycle problems during solidification and cooling and the absence of fumes and pollution during the process favors the quality of the welded joint. The life of metal joints could be greatly reduced in a corrosive environment, since the less noble material will tend to increase its corrosion rate while the nobler one will reduce its electrochemical dissolution. Accelerated ageing tests (i.e. salt fog test) are used to estimate the lifetime of metal joints in highly aggressive environments. The aim of the present work is to evaluate the durability at long ageing time in salt spray test (according to ASTM B117) of carbon steel/aluminum alloy joints, obtained by FSW. In this first part, mechanical tests results are reported. A deep metallographic and chemical investigation are going to be reported in the part 2.

Sr4Al6O12SO4 samples were obtained from the compound mixture formed by a solid–state reaction of Al2O3, SrSO4, and SrCO3. Samples were compacted at 100MPa to form pellets of 1 and 4cm in diameter and were sintered at 1400°C for 4 hours. The compound was analyzed by X–ray diffraction. Static immersion and wettability tests were performed to evaluate corrosion resistance in contact with Al–Si. Corrosion tests were carried out by immersion at 800, 900, and 1000°C for 24, 50, and 100 hours, while wettability was carried out at 900, 1000, and 1100°C for 2 hours. Subsequently, the samples were prepared metallographically. Samples were analyzed by optical microscopy, scanning electron microscopy, and image analysis. In general, reaction products consisting of alumina, spinel, oxides, and sulfates were found. The contact angles obtained were 124° to 135°. It is concluded that ceramic substrate Sr4Al6O12SO4 is resistant to corrosion by Al–Si alloy, since the slight thickness of the reaction products found in the samples (100μm) considering the severe conditions of the experiment: 1000°C and 100 hours of isothermal temperature. Furthermore, it can be said that Sr4Al6O12SO4 is not wettable by Al–Si alloys.

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

Epoxy was blended with benzoxazine resin and aluminum trihydrate (ATH) additive to render flame retardancy while maintaining mechanical properties. The ATH was modified using three different silane coupling agents and then added to 60/40 epoxy/benzoxazine mixtures. The effect of blend compositions and surface modification on flame retardant and mechanical properties of the composites was investigated by UL94, tensile, and shear tests. Resin mixtures containing more than 40 wt% benzoxazine revealed a UL94 V-1 rating with enhanced tensile and shear strength. Upon addition of 20 wt% ATH to 60/40 epoxy/benzoxazine, a V-0 rating was achieved. The lowered tensile and adhesive properties of the composites in the presence of ATH were improved by modifying the ATH surface using silane coupling agents.

Background: Aluminum phosphide (AlP), also known as “rice tablet,” is widely used as an effective pesticide. However, AlP poisoning is a common cause of mortality in many countries, such as Iran. Unfortunately, there is no specific antidote for AlP toxicity to date. AlP releases phosphine gas when it is exposed to moisture and acid. Phosphine is a robust mitochondrial toxin that could significantly inhibit cellular energy metabolism. AlP poisoning is an emergency condition that needs instant and effective intervention. Dihydroxyacetone (DHA) is a simple saccharide used for several pharmacological as well as cosmetic purposes. Previously, we found that DHA could significantly prevent mitochondrial impairment induced by toxic agents such as cyanide and phosphine in various in vitro and in vivo experimental models.Methods: Hospitalized patients (n = 111) were evaluated for eligibility criteria. Among these patients, n = 35 cases were excluded due to incomplete data (n = 11) and suspicion of poisoning rather than AlP (n = 24). Meanwhile, n = 76 cases with confirmed AlP poisoning were included in the study. AlP-poisoned patients who did not receive DHA (n =18) were used as the control group.Patients (n = 58) received at least one dose of DHA (500 ml of 5% DHA solution w/v, i.v.) in addition to routine treatment of AlP poisoning. Arterial blood gas (ABG), blood pH, bicarbonate levels, and other vital signs and biochemical measurements were monitored. Moreover, the mortality rate and time of hospitalization were evaluated in both DHA-treated (n = 58) and AlP-poisoned patients without DHA administration (n = 18). Several biomarkers were assessed before (upon hospitalization) and after DHA treatment. The routine tests for AlP-poisoned patients in this study were the measurement of electrolytes (K+ and Na+), WBC, RBC, hemoglobin, INR, carbonate (HCO3), blood pH, PaCO2, and PaO2 and SGPT, SGOT, BUN, Cr. Results: Upon patients' admission, significant decreases in blood pH (acidosis), blood PaO₂, and HCO₃ levels were the hallmarks of AlP poisoning. It was found that DHA significantly alleviated biomarkers of AlP poisoning and tremendously enhanced patients’ survival rate compared to patients treated based on hospital routine AlP poisoning protocols (no DHA). No significant adverse effects were evident in DHA-treated patients in the current study.Interpretation: These data suggest that parenteral DHA is a novel and effective antidote against AlP poisoning.Trial registration: IR.SUMS.REC.1394.102

The conductor aluminum alloys Al-0.25wt.%Zr doped additionally with Х = Er, Si, Hf, and Nb were the objects of investigations. The fine-grained microstructure in the alloys was formed by Equal Channel Angular Pressing and Rotary Swaging. The thermal stability of the microstructure, specific electrical resistivity, and microhardness of the novel conductor aluminum alloys was investigated. The mechanisms of nucleation of the Al3(Zr,X) secondary particles during annealing the fine-grained aluminum alloys were determined using Jones-Mehl-Avrami-Kolmogorov equation. Using Zener equation, the dependencies of the mean secondary particle sizes on the annealing time were obtained on the base of analysis of the data on the grain growth in the aluminum alloys. The secondary particle nucleation during long-time low-temperature annealing (300 оC, 1000 hrs) was shown to go preferentially at the cores of the lattice dislocations. The Al-0.25%Zr-0.25%Er-0.20%Hf-0.15%Si alloy subjected to long-time annealing at 300 оC has the optimal combination of the microhardness and electrical conductivity (59.8%IACS, Hv = 480 ± 15 MPa).

The research was undertaken to study the way deformation behaves in ultrafine-grained (UFG) conducting Al-Zr alloys doped with Sc, Hf, and Yb. All in all, 8 alloys were studied with zirconium partially replaced by Sc, Hf, and/or Yb. Doping elements (X = Zr, Sc, Hf, Yb) in the alloys total 0.4 wt.%. The choice of doping elements is conditioned by possible precipitation of Al3X particles with L12 structure while annealing these alloys. Such particles provide higher thermal stability of a nonequilibrium UFG microstructure. Initial coarse-grained samples were obtained by induction casting. The UFG microstructure in the alloys was formed by Equal Channel Angular Pressing (ECAP) at 225°C. Superplasticity tests were carried out at temperatures ranging from 300 to 500 °C and strain rates varying between 3.310-4 and 3.310-1 s-1. The highest values of elongation to failure are observed in Sc-doped alloys. A UFG Al-0.2%Zr-0.1%Sc-0.1%Hf alloy has maximum ductility: at 450 °C and a strain rate of 3.310-3 s-1, relative elongation to failure reaches 765%. At the onset of superplasticity, stress–strain curves are characterized by a stage of homogeneous strain and a long stage of localized plastic flow. The dependence of homogeneous strain (eq) on test temperature in UFG Sc-doped alloys is increasing uniformly, which is not the case for other UFG alloys with eq(T) dependence peaking at 350-400 оС. Strain rate sensitivity coefficient of flow stress m is small and does not exceed 0.26-0.3 at 400-500 °C. In UFG alloys containing no scandium, m coefficient is observed to go down to 0.12-0.18 at 500 оС. It has been suggested that lower m values are driven by intensive grain growth and pore formation in large Al3X particles, which develop specifically at the ingot crystallization stage.

The solid-state welding method known as friction stir welding (FSW) bonds two metallic work parts, whether the same or different, by plastically deforming the base metal. The frictional resistance between both metallic work pieces causes them to produce heat, which produces plastic deformation and welds them. However, the weldability and strength of FSW joints mainly depend on the FSW parameters. This review work highlights the previous research work on the FSW parameters and their effects on the weldability and quality of the aluminum alloys joined with similar and dissimilar metals through the FSW method. About 150 research studies were systematically reviewed, and the articles included data from peer-reviewed journals. It has been concluded that the key parameters, including welding speed, “rotational speed”, “plunge depth”, “spindle torque”, “shoulder design”, “base material”, “pin profile” and “tool type", significantly affect the weldability of the aluminum joint through the FSW method. Also, the selection of these parameters is important and fundamental as they directly affect the joint. It is recommended that future work focus on FSW for aluminum. Among these, the most essential is the application of artificial intelligence (AI) techniques to select the optimum FSW parameters for aluminum welding.

Microalgal harvesting is one of the most challenging processes in the development of algal research and development. Several methods, such as centrifugation, flocculation, and filtration, are available at the laboratory scale. However, the requirement of expensive pieces of equipment and the possibility of biomass contamination are recurring gaps that hinder the development of microalgae I+D in different parts of the world. Recently, the electroflotation has been proved as a suitable method for the harvesting of different species of microalgae and cyanobacteria. To this day, there are no companies that sell laboratory-scale electroflotation equipment; this is mainly due to the gap in the knowledge on which factors (time, mixing rate, number of electrodes, and others) will affect the efficiency of concentration without reducing the biomass quality. This paper aims to build an innovative low-cost electroflotation system under 300 USD with cheap and resistant materials. To achieve our goal, we test the interaction of three variables (time, mixing rate, and amount of electrodes) were evaluated. Results showed that an efficiency closer to 100% could be achieved under 20 minutes using >10 electrodes and 150 rpm. We hope this innovative approach can be used by different researchers to improve our knowledge of the concentration and harvesting of algae and cyanobacteria.

In this paper, the effect of preheating on the mechanical properties and micro structure of similar friction stir welded AA6061 aluminum alloys sheets was investigated. Aluminum alloy 6061 sheets with a thickness of 5 mm and threaded cylindrical pins were used. Rotation and traverse speeds were 1200 rpm and 75 mm/min, respectively. The results of tensile tests performed on the welded samples showed that compared to the non-preheated samples, preheating had increased the strength and elongation of the joints by 58% and 46%, respectively. In the present study, during the welding process preheating cause emerged heat with lower slope from stir zone. This phenomenon may result in Increase the deformation resistance of material and consequently decrease of grain size. This grain refinement can improve the mechanical properties of welds. Accordingly, hardness and strength of the material will be increased.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

Researchers are increasingly focusing on green synthesis methods for silver nanoparticles due to their cost-effectiveness and reduced environmental impact. In this study, we utilized an edible bird's nest (EBN), a valuable economic resource, as the primary material for synthesizing silver nanoparticles using only water as the solvent. Metabolite profiling of the EBN extract was conducted using LC-QTOF-MS in positive mode (ESI+), revealing the presence of lipids, glycosides, peptides, polysaccharides, and disaccharides. Upon the addition of silver nitrate to the aqueous EBN extract, noticeable color changes from transparent to brown indicated the successful formation of AgNPs. Subsequent characterization of these silver nanoparticles involved UV-Visible spectroscopy, which revealed an absorption peak at 421 nm. Further characterization was carried out using Field Effect Scanning Electron Microscopy (FESEM), Attenuated Total Reflectance-Fourier Infrared (ATR-FTIR) spectroscopy, and Energy Dispersive X-Ray (EDX) analysis. The involvement of phenolic agents, proteins, and amino acids in reducing the silver particles was confirmed. The synthesized nanoparticles exhibited a crystalline nature, a spherical shape, and a particle size ranging from 10 to 20 nm. The presence of elemental silver was confirmed by a strong, intense peak around 3 keV in the EDX spectrum. To assess their potential, the antibacterial properties of the silver nanoparticles against Escherichia coli and Staphylococcus aureus were evaluated using the agar diffusion method.

Background: Antibiofilm activity of silver nanoparticles has been extensively investigated in common bacteria. Metallo-β-lactamase producing Gram-negative bacteria are hard-to-treat microorganisms with few therapeutic options, and silver nanoparticles were not evaluated on the biofilm of these bacteria. Objectives: The aim of this study was to evaluate the antibiofilm activity of a bone scaffold impregnated with silver nanoparticles in NDM-producing Gram-negative bacilli. Methods: Bone scaffolds from bovine femur were used for the tests and impregnated with silver nanoparticles (50 nm) by physical adsorption. Silver nitrate minimal inhibitory and bactericidal concentrations (MIC and MBC) were performed on NDM-producing Escherichia coli, Klebsiella pneumoniae, and Pseudomonas aeruginosa. Disc diffusion tests for silver nanoparticles susceptibility and quantification of biofilm production on plate and bone with sessile cell count were performed. Results: The MIC results demonstrated that silver nitrate had an antimicrobial effect on all microorganisms, inactivating the growth of isolates from a concentration of 8 µg/mL. MBC results showed that E. coli 16.211 was the only isolate to present MIC different from MBC, with a value of 16 µg/mL. Conclusion: Bone scaffolds impregnated with silver nanoparticles can significantly reduce biofilm, and it can be a strategic material to be used as an implant for different approaches.

Silver nanoparticles from Origanum vulgare (Oregano) have been synthesized in the past. However, no investigation has been performed on the combined effects of independent factors that affect the synthesis. Silver nitrate and Oregano concentrations, incubation temperature and time, as well as pH can play crucial roles in synthesis. In this regard Full Factorial Design was applied. A Voigt function was fitted on the measured UV – Vis spectra. The fitting parameters of the Voigt function (peak wavelength, area, and Full Width at Half Maximum) were used as the responses. A quadratic model was fitted for the peak wavelength and area, and the pH proved the dominant factor on nanoparticle synthesis.

In this contribution, time course studies were performed toward oxidation of different peroxidase substrates in the presence of silver nanozymes. In this regard, two common peroxidase substrates, TMB and DAB, were selected as model chromogens. The process of the oxidation reaction was probed by recording the absorbance of the colored products using UV-Vis spectrophotometer. Thereafter, the nanozymatic activity was calculated and used as an index for comparing the performance of the silver nanozymes against different substrates in a certain reaction time. The time course curves, revealed that the maximal activity of the silver nanozymes were achieved after a very short time of 3.0 min toward TMB oxidation while regarding DAB, the maximal activity was observed after 25.0 min which is 6.5-fold slower than that of the TMB oxidation. The difference between the DAB and TMB can be assigned to their different reaction pathways and different reactivity. In fact, the oxidation of DAB has occurred via n-electron irreversible pathway while the TMB oxidation has occurred through a simple 2-electon reversible pathway. Besides, DAB is a high stable and less relative compound compared of TMB, resulting different oxidation times, different affinity for binding to nanozyme active nodes which lead to different nanozymatic activities.

The production of nanoparticles enhances the bioactivity of biological molecules for drug delivery to infection sites. This study explains how silver nanoparticles (AgNPs) coating enhanced the hypoglycemic effects of vanillic acid in male diabetic rats with diabetes brought on by streptozotocin. (STZ). Four groups of 24 rats were created for the investigation and divided into them. The first group rats (G1; untreated) were given a basal diet, whereas the other three groups all developed diabetes through STZ injection. Diabetic rats who were not getting therapy were included in the second group (G2; STZ-positive), whereas the other diabetic rats were divided into the third group (G3, vanillic acid-treated) and the fourth group (G4; AgNPs-coated vanillic acid treated). The treatment lasted four weeks. In G2, the induction of diabetes led to an increase in serum glucose, glycated proteins, renal indices, interleukin-6 (IL-6), K+, immunoglobulins, and lipid peroxidation, while decreased Ca++, Na+, and other antioxidants in the kidney tissue homogenate. In addition, aberrant signs were present in the pancreas and kidneys of diabetic rats. The renal and pancreatic tissues were effectively enhanced by vanillic acid or vanillic acid-coated AgNPs, bringing them very close to their pre-diabetic conditions. AgNPs-coated vanillic acid offered a stronger defense against STZ-induced diabetes and lessened the effects of hyperglycemia compared to ordinary vanillic acid. Additionally, using vanillic acid coated with silver nanoparticles greatly reduced inflammation when compared to using vanillic acid alone. This outcome suggests increased antioxidant activity.

Scutellaria multicaulis, a member of the Lamiaceae, is a medicinal plant indigenous to Iran, Afghanistan, and Pakistan. It has been widely used as a prominent herb in traditional medicine for thousands of years. This plant is reported with baicalein, wogonin, and chrysin flavonoids as a significant group of chemical ingredients, which can cure different diseases such as breast cancer. S. multicaulis leave extract was used for the bioreduction of silver nanoparticles (SmL-Ag-NPs), and their phytochemical contents and antioxidant, antibacterial, anti-proliferative, and apoptotic activity were evaluated. Optimal physicochemical properties of SmL-Ag-NPs were obtained by mixing 5% of leave extract and 2 mM of aqueous AgNO3 solution and confirmed by characterization studies including UV–visible spectrophotometry, FE-SEM, EDX, DLS, zeta potential, TGA, SERS, XRD and FTIR Spectroscopy. SmL-Ag-NPs exhibited higher content of TPC (Total Phenolic Content) and TFC (Total Flavonoid Content) and potential antioxidant activity. SmL-Ag-NPs also demonstrated dose-dependent cytotoxicity against MDA-MB231 cells multiplication with an IC50 value of 37.62 μg/mL at 48h through inducing cell apoptosis. This is the first report on the biosynthesis of silver nanoparticles using S. multicaulis leave extract, which can provide treatment for cancer diseases and reduce some negative effects of chemotherapy.

Abstract composite silver nanoparticles were synthesised using melanin broth and Arabic gum as a reducing and binding agent. The reactions are carried out with water because it is a non-hazardous solvent. The produced composites either had specified diameters (average diameter of 50 nm) with high silver loading or lower loading composites with tuneable morphologies and electrical properties. UV-IR, gamma, and conventional light are used to characterise the synthesised composite silver nanoparticles. Furthermore, measurements are carried out of the dielectric constant, refractive index, energy gap, optical and electrical conductivities, and refractive index coefficients. The silver nanoparticle formation was validated by UV-Vis measurement of the sample, which demonstrated a distinct peak at a wavelength of 420 nm. The characteristics of the composite silver nanoparticles are also quantified using several methods, including XRD, SEM, and particle size analysis.

Sphalerite has been recognized as the most important carrier of critical metal of Indium (In) due to that In mainly exists in the sphalerite lattice by isomorphic substitution. There are two significant replacing schemes for In entry into sphalerite, these are, Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+. In order to understand the reaction process and constraints of the two substitution schemes, this paper uses first-principles methods to calculate In and Ag, Cu replacing Zn in sphalerite. According to the substitution schemes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, two doped sphalerite systems of Zn30InAgS32 and Zn30InCuS32 were constructed using 2×2×2 supercell model of sphalerite. Firstly, the pressure is controlled to 30MPa, and the temperature is set from 20-40MPa to simulate the response of the two doped sphalerite systems to temperature; Then, the control temperature was unchanged to 600K, and the pressure was set from 20-40MPa to investigate the pressure control of the two doped sphalerite systems. The lattice parameters, substitution energy, electronic structure, and population analysis of the designed models before and after replacement have been critically compared. The main conclusions can be drawn that it is more stable for In to enter sphalerite via the coupled substitution scheme Cu++In3+→2Zn2+, and the conditions that the two substitution schemes most likely to occur are 650K and 40MPa. This study not only reveals the physical and chemical properties of In-rich sphalerite formed by the two reaction processes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, but also has a certain enlightenment effect on the search for indium in sphalerite, and promotes the application of first principles in mineralization analysis.

Diabetes is a life-threatening disease and chronic diabetes affects the parts of the body including the liver, kidney and pancreas. The root cause of diabetes is mainly associated with oxidative stress produced by reactive oxygen species. The minocycline is a polyphenolic drug with excellent antioxidant activities. The objective of the present study was to investigate the antidiabetic potential of minocycline modified silver nanoparticles (Mino/AgNPs) against alloxan-induced diabetic mice. The Mino/AgNPs were synthesized using minocycline as reducing and stabilizing agents. UV-vis, FTIR, X-ray diffraction (XRD) and transmission electron microscopy (TEM) were applied for the characterization of Mino/AgNPs. The 2,2-diphenyl-1-picrylhydrazyl (DPPH) free radical scavenging assay was conducted to determine the antioxidant potential of newly synthesized Mino/AgNPs. The results revealed that the Mino/AgNPs showed higher radical scavenging activity (IC50 = 19.7 µg/mL) as compared to the minocycline (IC50 = 26.0 µg/mL) and ascorbic acid (IC50 = 25.2 µg/mL). Further, the Mino/AgNPs were successfully employed to examine their antidiabetic potential against Alloxan-induced diabetic mice. Hematological results showed that the mice treated with Mino/AgNPs demonstrated a significant decrease in fasting blood glucose level and lipid profile as compared to the diabetic group. The histopathological examination confirmed that the diabetic mice treated with Mino/AgNPs showed significant recovery and revival of histo-morphology of kidney, central vein of liver and islet cells of the pancreas compared to the diabetic mice. Hence Mino/AgNPs have good antidiabetic potential and could be an appropriate nanomedicine to prevent the development of diabetes.

This work emphasizes to use silver decorative method to enhance the antibacterial activity of TiO₂ and ZnO nanoparticles. These silver decorated nanoparticles (hybrid nanoparticles) were synthesized by using sodium borohydride as a reducing agent, with the weight ratio of Ag precursors: oxide nanoparticles = 1: 30. The morphology and optical property of these hybrid nanoparticles were investigated using transmission electron microscopy (TEM) and UV–vis spectroscopy. The agar-well diffusion method was used to evaluate their antibacterial activity against both Staphylococcus aureus and Escherichia coli bacteria, with or without light irradiation. The TEM images indicated clearly that silver nanoparticles (AgNPs, 5-10 nm) were well deposited on the surface of nano-TiO₂ particles (30-60 nm). Besides, smaller AgNPs (< 2 nm) were dispersed on the surface of nano-ZnO particles (20-50 nm). UV-vis spectra confirmed that the hybridization of Ag and oxide nanoparticles led to shift the absorption edge of oxide nanoparticles to the lower energy region (visible region). The antibacterial tests indicated that both oxide pure nanoparticles did not exhibit inhibitory against bacteria, with or without light irradiation. However, the presence of AgNPs in their hybrids, even at low content (< 40 mg/mL) leads to a good antibacterial activity and the higher inhibition zones under light irradiation as compared to that in dark was observed.

Metal nanoparticle has been reported to have a high antimicrobial activity against fungi, bacteria, and yeasts. In this study, silver nanoparticles (AgNPs) were synthesized using a chemical reduction method, at 90 oC, and used as an antifungal coating in paper packaging, to control the growth of C. gloeosporioides in cut orchid flowers during shipping. AgNPs were characterized by UV-Vis spectroscopy and atomic force microscope (AFM). The results indicated that the shape of AgNPs was spherical and homogenous with an average size of 47 nm. Twenty and 50 particles per million (ppm) concentration of AgNPs, mixed with starch, were prepared as the coating solution. The paper coated with 50 ppm AgNPs exhibited a significant antifungal activity against C. gloeosporioides compared to 20 ppm AgNPs coating. The AgNPs coated paper had a better water resistance and mechanical properties compared to paper without coating. We observed a significant reduction in the number of anthers, of orchid inflorescences, infected by C. gloeosporioides, when stored in the coated boxes. The current study demonstrates that paper boxes coated with AgNPs are a potential solution to control the infection of C. gloeosporioides in the storage of cut orchid flowers.

Silver nanoparticles (AgNPs) have been demonstrated to restrain bacterial growth while maintaining the minimal risk in development of bacterial resistance and human cell toxicity that conventional silver compounds exhibit. Several physical and chemical methods have been reported to synthesize AgNPs. However, these methods are expensive and involve heavy chemical reduction agents. An alternative approach to produce AgNPs in a cost-effective and environmentally friendly way employs a biological pathway using various plant extracts to reduce metal ions. The size control issue and the stability of nanoparticles remain some of the latest challenges in such methods. In this study, we used two different concentrations of fresh leaf extract of the plant Arbutus Unedo (LEA) as a reducing and stabilizing agent to produce two size variations of AgNPs. UV-Vis spectroscopy, Dynamic Light Scattering, Transmission Electron Microscopy and zeta potential were applied for the characterization of AgNPs. Both AgNP variations were evaluated for their antibacterial efficacy against the gram-negative species Escherichia coli and Pseudomonas aeruginosa, as well as the gram-positive species Bacillus subtilis and Staphylococcus epidermidis. Although significant differences have been achieved in the nanoparticles’ size by varying the plant extract concentration during synthesis, the antibacterial effect was almost similar.

: The paper presents the results of uniaxial tensile tests of samples of hypoeutectic aluminum-silicon alloy A319. According to the results of which the influence of surface treatment by a pulsed electron beam on the mechanical properties of the material was determined. The peculiarities of localization of deformation in the material, caused by grinding of the surface layer material structure due to rapid crystallization during electron beam treatment were revealed. The surface treatment up to 100 µm depth leads to the formation of a fine dendritic columnar structure of silumin and to an increase in the plasticity of the samples. The influence of surface treatment affects the increase of deformation localization in the region of stable concentrator before failure. The largest increase in ductility and localization of deformation occurs during processing with energy density of 15 J/cm2. In the process of specimen deformation, unstable, metastable, and stable areas of plastic deformation localization are formed and replaced, and the formation of stable areas of localized plastic deformation, in which the specimen fails at the end of the test, can be detected at the initial stages of testing. In specimens, during testing in the zone of localized plastic deformation, bands are formed that pass through the entire surface of the specimen at an angle from 35 to 55 degrees to the axis of tension, their evolution leads to the formation of stable zones of localized plastic deformation and to the failure of the specimen.

The results of the study of the influence of the size of cylindrical samples of A5N aluminum on the time and rate of their cooling are presented. According to experimental data, the temperature dependence of the heat transfer coefficient for pure metals is calculated. It revealed that the process of cooling of the aluminium and its alloys has a relaxation behavior. It has found that the main mechanisms of natural air cooling are convection heat transfer and radiation. The characteristic cooling time due to radiation is less than due to convection. The contribution of thermal radiation is noticeable at high temperatures. It was found that the characteristic times of cooling due to radiation and convection increase with increase in volume to area ratio of the sample.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

Since the first generation of 7xxx superhard aluminum alloy was investigated in 1930, hitherto the fifth generation aluminum alloy materials with high comprehensive properties such as high static strength, high strength, heat resistance, high toughness, damage resistance, low density and low quenching sensitivity have been improved and developed. This paper reviews the progress of 7xxx aluminum alloy materials in composition, microstructure, properties, preparation methods, heat treatment strengthening and applications from 2014 to 2021. The effect of adding trace elements on microstructure and properties of 7xxx series alloy and the problems existing in aging precipitation characteristics and reinforcement mechanism are discussed. The future development direction of 7xxx superhard aluminum alloy is prospected by optimizing heat treatment technological, adding appropriate trace elements to alloy and controlling alloy microstructure.

The 8Nb isopleth section of a Ti-Al-Nb system is experimentally determined based on thermal analysis and thermodynamic calculation methods to obtain the phase transformation and equilibrium relations required for material design and fabrication. The phase transus and relations for the 8Nb-TiAl system show some deviations from the calculated thermodynamic results. The ordered βo phase transforms from the disordered β/α phases at 1200–1400 °C over a large Al concentration range, and this transformation is considered to be an intermediate type between the first- and second-order phase transitions. Moreover, the βo phases are retained at the ambient temperature in the 8Nb-TiAl microstructures. The ωo phase transforms from the highly ordered βo phase, rather than from α2 or βo with low degree of atom ordering B2 (LOB2) structure, with Al concentration of 32–43 at.% at approximately 850 °C. From the experimental detection, the transition of the ωo phase from the βo phase is considered to be a further ordering process.

Several challenges stand in the way of production of Metal Matrix Composites (MMCs) such as higher processing temperatures, particulate mixing, particulate-matrix interface bonding issues and ability to process into desired geometrical shapes. Although there are many literatures showing composites with single particulate reinforcements, the studies on composites with multiple reinforcing agents (hybrid composites) are found to be limited. Development of a hybrid particulate composite with optimized mechanical and tribological properties is very significant to suit modern engineering applications. In this study, Al-Si hypereutectic alloy (A390) is used as the matrix and Silicon Carbide (SiC) and Graphite (Gr) and Molybdenum di-Sulphide (MoS₂) are used as particulates. Particulate volume (wt%) is varied and sample test castings are made using squeeze casting process through stir casting processing route. The evaluation of mechanical properties indicates that presence of both the hard phase (SiC) and the soft phase has distinct effect on the properties of Hybrid Composite. Composite samples were characterized to understand the performance and to meet the tribological applications. Fractography study indicated an intra-granular brittle fracture for hybrid composites. Wear study shows that Hybrid MMCs has better tribological performance compared to that of A390 alloy.

Aluminum alloy Al 2024-T3 were successfully joined using friction stir spot jwelding joining (FSSW). Satisfactory joint strengths were obtained at different welding parameters (tool rotational speed, tool plunge depth, dwell time) and tool pin profile (straight cylindrical, triangular and tapered cylindrical). Resulting joints were welded with welded zone. The different tools significantly influenced the evolution on the stir zone in the welds. Lap-shear tests were carried out to find the weld strength. Weld cross section appearance observations were also done. The macrostructure shows that the welding parameters have a determinant effect on the weld strength (x: the nugget thickness, y: the thickness of the upper sheet and SZ: stir zone). The main fracture mode was pull out fracture modes in the tensile shear test of joints. The results of tensile shear tests showed that the tensile-shear load increased with increasing rotational speed in the shoulder penetration depth of 0.2 mm. Failure joints were obrerved in the weld high shoulder penetration depth and insufficient tool rotation.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

Nanofibers are one of the most attractive materials that can modify functionalities for developing new kinds of specific applications, mainly used as a biomedical material. Herein, we designed and prepared the antibacterial nonwoven fiber mats of PLA and PLA composited with Ag nanoparticles by electrospinning. The effects of varying filler contents on their chemical, surface morphology, thermal, water absorbency, and antibacterial properties were investigated using FTIR, SEM/EDS, DSC, swelling ratio, and qualitative and quantitative antibacterial tests. FTIR and EDS spectra indicated that Ag nanoparticles were incorporated in the PLA without chemical bonding. SEM revealed that the average diameter of the PLA nanofibers containing the Ag nanoparticles was more significant than those without those particles. Besides, fiber diameters are proportionally the amount of Ag nanoparticle contents. DSC indicated that the Ag nanoparticles can be incorporated within the PLA-matrix without strongly affecting their thermal properties. Moreover, the crystallinity of the composite nonwoven fiber mats was higher than those of fiber mats in the neat PLA. Accordingly, the antibacterial activities revealed that all the composite nanofiber mats exhibited excellent against S. aureus and E. coli bacterial strains. In addition, in the cell toxicity study, all produced hybrids nonwoven fiber mats induced a reduction in cell viability for the L929 fibroblast cells. Our results suggest that the designed and prepared nonwoven fiber mats may have good potential for use in the biomedical field, particularly in wound dressing applications

A new one-pot technique for preparation of polysaccharide-based Pd- and Pd-Ag nanocatalysts by sequential supporting natural polymer (2-hydroxyethyl cellulose (HEC), chitosan (Chit), pectin (Pec)) and metals on zinc oxide was developed. The nanocatalysts based on polysaccharide were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET), infrared spectroscopy (IRS), X-ray powder diffraction (XRD), X-ray photoelectron spectra (XPS) and elemental analysis methods. The catalyst characterization results indicated complete adsorption of polysaccharide and metal ions on zinc oxide, forming polymer-stabilized Pd nanoparticles of ~2 nm in size, evenly distributed on the support surface. The catalysts were studied in the hydrogenation of 2-hexyn-1-ol under mild conditions (0.1 MPa, 40 °C). The catalysts demonstrated nearly the same conversion of 2-hexyn-1-ol. The selectivity to cis-hexen-1-ol of the catalysts decreases in the following order: 0.5%Pd-Ag(3:1)HEC/ZnO>0.5%Pd-Ag(3:1)Pec/ZnO>0.5%Pd-Ag(3:1)Chit/ZnO. The optimum reaction temperature and catalyst loading for the Pd-Ag catalysts modified with HEC and Chit have been determined (40 °C, 0.05 g).

Nanoparticles (NPs) have uniform chemical composition, size, and morphology. Microorganisms are of great interest in Nanoparticle synthesis. The green production of nanomaterials occurs either intracellularly or extracellularly. Gold and silver nanoparticles are mostly synthesised by the enzymatic degradation of metal ions. The produced NPs are characterized by different instruments such as ultraviolet visible, dynamic light scattering, x-ray diffraction, scanning electron microscope, transmission electron microscope, etc. Our review discusses the various biomedical applications of gold and silver nanoparticles synthesized by microbes via intracellular and extracellular mechanisms.

The Computational theoretical techniques using first principle which make use of the density functional theory as implemented by quantum expresso as well as inter – atomic force constant (IFC) techniques (Born-von Jarman) were used to investigate the phonon dispersion curves of Silver (Ag) and Gold (Au) The results obtained show that for Au, the extension to 1 – 6^th neighbour gave slightly close agreement with the experimental phonon dispersions when compared to the 1 – 5^th neighbor at W_T and L_L symmetry points. The percentage error for Au at W_T are 2.5% and 2.9% ; at point L_L we obtained 0.6% and 0.7% respectively. The Local density Approximation (LDA) results for Ag underestimates the lattice with about 1.6% while the Generalized Gradient Approximation (GGA) overestimates it by 1.9%.

Present study reports the green synthesis of pectin fabricated silver-based nanocomposite (Pectin-AgNPs) with Carpesiumnepalense leaves extract and evaluated their bactericidal kinetics, in-vivo hepatoprotective and cytotoxic potentials with their possible mechanisms. GC/MS and LC/MS analysis indicated the presence of different new phytochemicals constituents in the plant extract. The physicochemical characterization of Pectin-AgNPs by UV/Vis, SEM, DLS, FTIR and EDX techniques showed the spherical and uniform size range synthesis of nanocomposite i.e. 50-110 nm. The highly significant (P<0.005) antibacterial activity was found against all tested four bacterial strains with the ZIs of 24.8 to 27.2 mm. Significant damage in bacterial cell membrane was also observed in AFM study after treated with Pectin-AgNPs. At the doses of 0.05 mg/kg, nanocomposite showed highly significant (P<0.005)hepatoprotective activity in biochemical and histopathology analysis as compared to CCL4 administered control group. The ameliorative effects of Pectin-AgNPs were observed in PCR analysis on both GAPDH and PPARs genes expression and its potential to restore gene alterations caused by CCl4 intoxication.Pectin-AgNPs produced cytotoxic activity against HeLa cell lines at higher doses with the LC50 of 223.7 µg/mL. The current findings demonstrate positive attributes of pectin fabricated AgNPs as a promising antibacterial, hepatoprotective and cytotoxic agent.

Two antimicrobial agents such as silver nanoparticles (AgNPs) and titanium dioxide (TiO2) have been formulated with natural polysaccharides (chitosan or alginate) to develop innovative inks for the rapid, customizable, and extremely accurate manufacturing of 3D printed scaffolds useful as dressings in the treatment of infected skin wounds. Suitable chemical-physical properties for the applicability of these innovative devices were demonstrated through the evaluation of water content (88-93%), mechanical strength (Young’s modulus 0.23-0.6 MPa), elasticity, and morphology. The antimicrobial tests performed against Staphylococcus Aureus and Pseudomonas Aeruginosa demonstrated the antimicrobial activities against Gram+ and Gram– bacteria of AgNPs and TiO2 agents embedded in the CH or ALG macroporous 3D hydrogels (AgNPs MIC starting from 5 µg/ml). The biocompatibility of chitosan was widely demonstrated by cell viability tests and was higher than that observed for alginate. Constructs containing AgNPs at 10 µg/ml concentration level did not significantly alter cell viability as well as the presence of titanium dioxide; cytotoxicity towards human fibroblasts was observed starting with AgNPs concentration of 100 µg/ml. In conclusions, the 3D printed dressings here developed own the features to be cheap, highly defined, easy to be manufactured and further applied in personalized antimicrobial medicine applications.

The importance of understanding the corrosion mechanisms of excavated metal artefacts help in determining the physico-chemical parameters of the burial environment and the formation of different corrosion products. These products can be observed and analysed with the help of various techniques that provide information on their morphology, chemical composition and structure. The analysis of ancient coins is extremely challenging in the presence of heavily corroded surfaces; as quantitative information may not exactly concur with its bulk composition. In the case of silver coins, the use of surface information can be used as a guide for bulk composition only. The current study carries out investigation and characterization of selected coins from a large coin hoard excavated from Amheida, Dakhla oasis, Egypt. The study and analysis of the alloy composition and corrosion products was performed using a multi-technique approach which included Light optical microscopes, Scanning Electron microscope (SEM) coupled with energy dispersive spectroscopy (EDS) and X-ray diffraction analysis. Investigation of the coins revealed the presence of a thick active inhomogeneous corrosion crust, while analysis showed that the coins were made from a binary silver copper alloy (billon) while the corrosion crust was rich in chlorides and carbonates, later identified by XRD analysis as Paratacamite, Malachite and Chrysocolla.