Micro-Raman spectroscopy was carried out to evaluate the localized residual stresses in commercial Gallium Nitride-based devices, specifically AlGaN/GaN High Electron Mobility Transistors (HEMTs) in a novel packaging design provided by STMicroelectronics S.r.l. The packaging plays a key role in protecting the device core against the external environment, thus minimizing damages caused by mechanical shocks, exposure to light, and contact with chemicals, conjointly achieving an efficient heat dissipation rate. Even though the packaging is a required step for the proper functioning of ready-to-use electronic devices, its application typically may introduce mechanical stress to AlGaN/GaN HEMTs, which can result in various reliability issues. In this paper, we investigate the impact of packaging on residual stress by analyzing the frequency shift of the E2 Raman peak along GaN layers and at the GaN/Si interface. An extensive evaluation was conducted using both a packaged device and a wafer-level device. The correlation between Raman frequency shifts of the E2 mode was accurately quantified, revealing a stress mitigation of approximately 0.1 GPa. This reduction is ascribed to the compressive stress introduced by the packaging, which partially offsets the intrinsic tensile stress of the wafer-level device. The proposed methodology could, in principle, be implemented to improve the development of a packaging.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

1) Background: Capturing patients’ medical histories significantly influences clinical decisions. Errors in this process lead to clinical errors, increase costs and dissatisfaction among physicians and patients. Physicians in developing countries are overloaded with patients and cannot always follow the proper history-taking procedure. The challenges are acknowledged; however, a comprehensive understanding of the status and the remedies remained unexplored. 2) Objective: This paper aims to investigate the workload, history-taking challenges, and the willingness of the physicians to accept digital solutions. 3) Methods: A cross-sectional online survey was conducted on 104 physicians across Bangladesh, featuring 22 questions regarding their professional environment, workload, digitization status of health records, challenges in history-taking, and attitudes toward adopting digital solutions for managing patient histories; 4) Results: 92.67% of the physicians face workloads, 88.46% struggle in medical history-taking, and only 4.81% use digital medical records. About 70% struggle to complete the necessary history-taking steps, emphasizing the urgent need for solutions. An AI-based Smart Health Gantt Chart (SHGC) system has been introduced for their instant feedback. 93.27% of physicians expressed their willingness to use such a system. 5) Conclusions: The proposed SHGC has the potential to enhance healthcare efficiency in developing nations, benefit physicians, and improve patient-centered care.

The collaboration of multimodal transport documents is the foundation for conducting multimodal transport operations. Blockchain technology can effectively address trust issues and information sharing difficulties in current multimodal transport document collaboration. However, in current blockchain-based electronic document research, the bottleneck problem lies in the collaboration of multiparty in multimodal transport under the "one-bill coverage system". We design a blockchain platform architecture for multimodal transport, reshaping collaboration processes for different modes of transport based on the blockchain platform. It proposes a collaboration model for multimodal transport under the "one-bill coverage system" and performs model solving and case analysis. The obtained collaboration strategies are embedded into the platform's application layer. Finally, using Solidity language, it writes smart contracts related to multimodal transport under the "one-bill coverage system " and deploys and executes them on the Remix platform.

Volatile organic compounds (VOCs) released from plants have been correlated with disease-status. Analysis of VOCs using GC-MS is time-consuming, laboratory-based, and requires specialist training. Electronic nose devices (E-nose) provide a portable alternative. Three different E-nose devices were compared to assess how accurately they could detect Mango Twig Tip Dieback and Panama disease in banana. The devices were initially trained on known volatiles, then pure cultures of Pantoea sp., Staphylococcus sp., and Fusarium odoratissimum, and finally, on infected and healthy mango leaves and field-collected, infected banana pseudo-stems. The experiments were repeated three times with six replicates for each host-pathogen pair. The variation between healthy and infected host materials was evaluated by principal component and linear discriminant analysis, cross-validation and chemometric data analysis. GC-MS analysis was conducted contemporaneously and identified an 80% similarity between healthy and infected plant material. The portable C 320 was 100% successful in discriminating known volatiles but had a low capability in differentiating healthy and infected plant substrates. The advanced devices (PEN 3 / MSEM 160) successfully detected healthy and diseased samples with a high variance. The results suggest that E-nose devices are more sensitive and accurate in detecting changes of VOCs between healthy and infected plants compared to headspace GC-MS.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

This paper constituted an extension of two previous studies concerning the mathematical development of the grain boundary grooving in polycrystalline thins films in the cases of the evaporation/condensation and diffusion taken separately. The thermal grooving processes are deeply controlled by the various mass transfer mechanisms of evaporation–condensation, surface diffusion, lattice diffusion, and grain boundary diffusion. This study proposed a new original analytical solution to the mathematical problem governing the grain groove profile in the case of simultaneous effects of evaporation-condensation and diffusion in polycrystalline thin films submitted to thermal and mechanical stress, and fatigue effects; by resolving the corresponding fourth-order partial differential equation ∂y∂t=C∂2y∂x2-B∂4y∂x4 obtained from the approximation y'2≪1. The comparison of the new solution to that of diffusion alone proved an important effect of the coupling of evaporation and diffusion on the geometric characteristics of the groove profile. A second analytical solution based on the series development was also proposed. It was proved that change of the boundary conditions of the grain grooving profile largely affected the different geometric characteristics of the groove profile.

Hybride halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

Due to its large hole mobility, Organic Rubrene (C42H28) has attracted research questions on its applications in electronic devices. In this work, extensive first-principles calculations were made to predict some temperature and doping dependent properties of Organic Semi- conductor Rubrene. We use Density Functional Theory (DFT) to investigate the electronic structure, elastic and transport properties of the Orthorhombic phase of the Rubrene compound. The calcu- lated band structure shows the Orthorhombic phase has a direct bandgap of 1.26 eV. From the Vickers hardness (1.080 GPa), our calculations show that Orthorhombic Rubrene is not a super hard material and can find useful application as a flexible semicon- ductor. The calculated transport Inverse Effective Mass and Elec- tronic Fitness Function show that the Orthorhombic Rubrene Crystal Structure is a p-type thermoelectric material at high temperatures.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

: Considering that Einstein's relation between the diffusion coefficient and the drift mobility of the free randomly moving charge carriers in homogeneous materials including metals is always valid, it is shown that the effective electric force acting on free electrons in metal depends on the ratio between the kinetic free electron energy at the Fermi surface to the classical particle energy 3kT/2. The electrical resistivity of elemental metals dependence on very low temperatures has the quadratic term, which has been explained by electron-electron scattering. In this paper, it is shown that the quadratic term of the electrical resistivity at low temperatures is caused by scattering of the free RM electrons by electronic defects due to linear effective free electron scattering cross-section dependence on temperature, but not by electron-electron scattering.

Sustainable supply chain management (SSCM) represents a critical strategy for the electronics industry to balance economic objectives with environmental and social responsibility across complex global production networks. This multiple case study analysis investigates SSCM integration within leading Korean electronics manufacturers Samsung, LG, and Hyundai. In-depth qualitative data, focus groups, and sustainability report analysis reveals the policies, practices, results and implementation barriers related to incorporating sustainability criteria across procurement, manufacturing, distribution and recycling functions. Findings show sustainability considerations increasingly driven by cost, risk, reputational and regulatory factors, with vertical coordination initiatives helping transfer knowledge to assist suppliers on compliance and emissions reductions. Yet substantial obstacles persist around monitoring, coordination, transparency and technical capabilities, especially amongst lower tiers. The paper discusses how common reporting standards, ethical sourcing certification and partnerships can accelerate electronics supply chain sustainability. By mapping integration achievements and gaps, this study informs managerial best practices and policy reforms toward promoting socially and ecologically responsible models for Korea's vital export industry as it navigates rising stakeholder pressures.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

An optical frequency comb (OFC) generator based on an electro-optic Talbot laser and cross-phase modulation (XPM) in a high nonlinear fiber (HNLF) is designed and demonstrated. The Talbot laser is an electro-optic frequency shifting loop to produce repetition rate multiplied pulses, and these pulses working as a pump signal induce XPM process in the HNLF to modulate the phase of a probe signal. At the output of the HNLF, OFCs with a multiplied line-spacing can be generated. The effects of the pump power and the HNLF length on the performance of the generated OFCs are theoretically analyzed. In the experiments, the line-spacing of the generated OFCs is respectively multiplied to be 10 GHz, 15 GHz and 20 GHz with a factor of 2, 3 and 4. The center of the OFCs is tuned in a 4-nm range by adjusting the wavelength of the probe signal.

Thromboprophylaxis of hospitalized patients at risk of venous thromboembolism (VTE) presents challenges owing to patient heterogeneity and lack of adoption of evidence-based methods. Intuitive practices for thromboprophylaxis have resulted in many patients being inappropriately prophylaxed. Multiple interventions for thromboprophylaxis have been tested, including use of multifaceted approaches such as national VTE prevention programs with audits, use of passive alerts (either human or electronic), and more recently use of active clinical decision support (CDS) tools incorporated into electronic health records (EHRs). Multifaceted health-system interventions have shown mixed results in their ability to increase appropriate thromboprophylaxis and reduce VTE, unless mandated through a national VTE prevention program, though the latter approach is potentially costly, effort- and time-dependent. Studies utilizing passive human or electronic alerts have also shown mixed results in increasing appropriate thromboprophylaxis and reducing VTE. The use of active CDS tools holds the greatest promise, especially with further refinement and widespread implementation within various EHRs and clinical workflows. Recent-ly a universal cloud-based and EHR-agnostic CDS VTE tool revealed high adoption and effectiveness in increasing appropriate thromboprophylaxis and reducing major thromboembolism. This narrative review summarizes the literature on system-wide thromboprophylaxis interventions in hospitalized patients, with a focus on CDS tools.

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

Burn patients still represent an important challenge in critical care medicine today. These patients can develop significant neurological conditions up to intracranial hypertension, but as they find themselves hospitalized outside of neurocritical care and are often subjected to sedation for the complex management, they are sometimes underestimated. The aim of this study is to evaluate the feasibility of non-invasive methods for the early diagnosis of intracranial hypertension in these patients. In this prospective observational study, adult burn patients admitted to intensive care within the first 8 hours of the event were enrolled. These patients were studied through ultrasound measurement of optic nerve sheath diameter and intracranial vessel velocimetry with transcranial Doppler. In the 20 patients studied, no frankly pathological values were identified in the 3 different measurement stages (within 8 hours of the burn, then at 48 and 96 hours) and no correlations were identified between the measured values and the extension of the burn with the related risk of mortality. However, this study, one of a kind, demonstrates that these non-invasive methods are applicable to this specific patient population, and can represent an effective method for reducing the incidence of complications that are dangerous for survival.

A substantial spike in the need for quality healthcare has resulted from people being more cognizant of health issues. With blockchain, healthcare providers may safely share patient information electronically, which is especially important given the sensitive nature of the data contained inside them. However, flaws in the current blockchain design have surfaced since the dawn of quantum computing systems. The study proposes a novel quantum inspired blockchain system (Qchain) and constructs a unique entangled quantum medical record (EQMR)system with an emphasis on privacy and security. This Qchain relies on entangled states to connect its blocks. Automated production of the chronology indicator reduces storage capacity requirements by connecting entangled BloQ (blocks with quantum properties) with controlled activities. One qubit is used to store the hash value of each block. A lot of information regarding quantum internet is included in the protocol for the entangled quantum medical record (EQMR). EQMR can be accessed in Medical Internet of Things (M-IoT) systems may be kept private and secure, and their where-abouts can be monitored in the event of an emergency. The protocol also uses quantum authentication in place of more conventional methods like encryption and digital signatures. Mathematical research shows that the quantum converged blockchain (QCB) is highly safe against attacks such as the External attack, Intercept-Measure-Repeat attack, and Entanglement-Measure attack. The reliability and auditability evaluations of the entangled BloQ, as well as the quantum circuit design for computing the hash value, are presented. There's also a comparison between the suggested approach and several other quantum blockchain designs.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

Chrysanthemum tea, a typical health tea with the same origin as medicine and food, is famous for its unique health benefits and flavor. To clarify the influence of metabolites of different varieties of chrysanthemum tea on the formation of taste and quality differences, nontargeted metabolomics combined with electronic tongue analysis were used to characterize the correlation between metabolites profiles and taste characteristics of different quality chrysanthemum tea. Thirteen metabolites were identified as the key metabolites of the sensory quality difference between Huangju and Jinsi Huangju tea. Kaempferol, luteolin, genistein, and some quinic acid derivatives were correlated with the ‘astringent’ and taste attributes. In contrast, l-(-)-3 phenyllactic acid and L-malic acid were found to be the ‘bitterness’ and ‘umami’ in chrysanthemum tea. KEGG pathway enrichment analysis showed that the flavonoid and flavonol biosynthesis pathway had important effects on the sensory quality of chrysanthemum tea.

Abstract: A progressive neurological disorder was observed in a male neutered Weimaraner. Clinical signs included fecal incontinence, lethargy, moderate paraparesis, proprioceptive pelvic limb ataxia, falling, cognitive decline, incoordination, decreased interest in food, changes in posture, and episodes of trance-like behavior. Neurologic signs were first observed at approximately 4 years, 10 months of age and progressed slowly. Magnetic resonance imaging showed generalized brain atrophy with areas of white matter pathology. Humane euthanasia was elected at 6 years, 7 months of age due to increasing severity of the neurological signs. Autoflorescent intracellular granules were observed in the cerebral and cerebellar cortexes, optic nerve, and cardiac muscle of the affected dog. These abnormal inclusions in the cerebral cortex and cardiac muscle immunolabeled with antibodies to mitochondrial ATP synthase subunit c protein, like that observed in the neuronal ceroid lipofuscinosis group of lysosomal storage diseases. Immunolabeling also demonstrated pronounced neuroinflammation in brain tissues. The ultrastructural appearances of the disease-related inclusion bodies in the brain and optic nerve were quite variable. The ultrastructure and locations of many of the inclusions in the nervous tissues suggested that they were derived, at least in part, from the myelin surrounding axons. The storage bodies in the cardiac muscle were located in mitochondria-rich regions and consisted of parallel arrays of membrane-like components interspersed with electron-dense flocculent material. The disease was characterized by pronounced abnormalities in the myelin of the brain and optic nerve consisting of distinctive areas of ballooning between the layers of myelin. The whole genome sequence generated from the affected dog contained a homozygous G-to-A missense mutation in CNP, which encodes proteins with CNPase enzyme activity and a structural role in myelin. The mutation predicts a Thr42Met amino acid sequence substitution. Genotyping of archived Weimaraner DNA samples identified an additional G>A variant homozygote with a clinical history and brain lesions similar to those of the proband. Of 292 Weimaraners and over 4,000 other dogs of various breeds, the proband and the other Weimaraner that exhibited similar signs were the only two that were homozygous for the CNP missense variant. CNPase immunolabeling was widespread in brain tissues from normal dogs but was undetectable in the same tissues from the proband. Based on the clinical history, fluorescence and electron-microscopy, immunohistochemistry, and molecular genetic findings, the late-onset Weimaraner disorder likely results from the missense mutation that results in CNPase deficiency, leading to myelin abnormalities, accumulation of lysosomal storage bodies, and brain atrophy. Similar disorders have been associated with different CNP variants in Dalmatians and in human subjects.

Electronic waste (e-waste), characterized by the widespread disposal of electronic devices, shows a growing environmental challenge. In this study, we explore the electrocatalytic potential of gold nanoparticles supported on Vulcan obtained from e-waste for their application as electrocatalysts for the methanol oxidation reaction in alkaline media. Gold nanoparticles are synthesized from gold coatings recovered from Intel Pentium 4 processor pins, highlighting their sustainability as electrocatalyst precursors. Comprehensive characterization, including UV-Vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray dif-fraction, is performed to assess the electrocatalyst's structural properties. Electrochemical evalu-ation is carried out in 0.5 M KOH electrolyte employing the rotating disk electrode technique, us-ing cyclic voltammetry for the study of methanol oxidation. Remarkably, the gold nanoparticles show electrocatalytic activity on par with commercially synthesized counterparts, demonstrating the feasibility of this approach for sustainable electrocatalyst production. Thus, this research opens new routes for utilizing e-waste as a source of valuable catalyst materials, addressing en-vironmental and technological challenges in the field of alkaline fuel cells.

Aeromagnetic compensation plays a vital role in geomagnetic navigation and has received considerable attention throughout last few decades. Classical aeromagnetic compensation methods based on the Tolles–Lawson (T-L) model are mainly aimed at permanent, induced, and eddy-current magnetic interferences of aircraft platform, which ignores other stray magnetic field interference on the platform including the interferences caused by on-board electronic (OBE) systems. In order to cooperate with TL model, magnetometers are usually required to be installed on the extension rod outside the cabin, which is widely applied to geophysical magnetic survey. In order to ensure safety and reduce the cost of platform modification in geomagnetic navigation, it’s necessary to place magnetometers inside the cabin. It also further exacerbates the magnetic interferences and improves the difficulty of magnetic compensation. In this paper, a modified aeromagnetic compensation method is proposed, and the in-cabin OBE interferences are respectively modelled to be proportional to the currents and their temporal variations of different electronic devices. To ensure that modified model adapts to strong OBE interference in the cabin, a cut-off frequency determination method based on curvature calculation and a feature selection method based on correlation calculation are proposed. The cut-off frequency determination method helps to select passband filter which suitable for in-cabin OBE interference. The feature selection method can help to effectively select current and voltage inputs for modified model. In addition, principal component analysis (PCA) is adopted to reduce multicollinearity which is intensified by the extension of OBE interferences in coefficient-estimating. Experiments on public dataset are conducted to illustrate the effectiveness of the proposed method, and the best compensation result achieved 1.71nT of root mean square error (RMSE).

This scientific paper presents a comprehensive investigation into transient Fourier analysis in some electrical engineering applications. The article deals with two effective approaches for solving transient analysis whose application is rather novel. The first contribution uses combined the Fourier series analytic Laplace-Carson (L­C) transform methods in the complex domain using complex time vectors, thereby significantly simplifying the calculation of the original function. As the inverse transform goes back into the time domain, it employs the Cauchy-Heaviside (C­H) method. The second contribution uses the Fourier transform (F­Τ)for transient analysis of a power converter electrical circuit with the passive and the active load. The method of complex conjugated amplitudes is used for steady-state analysis. Both contributions represent a new approach to this paper. The starting point is the Fourier series/expansions, computation of the Fourier coefficients, then continuing by solving the steady and transient states of the system and confirming the transient states using the Fourier transform. To validate our findings, the worked-out analytical results are verified by modelling in Matlab/Simulink environment.

The electronic nose (e-nose) is an innovative device that mimics the human olfactory system, allowing for the detection and identification of numerous scents. This abstract gives an in-depth examination of the current status of electronic nose technologies, with an emphasis on sensing mechanisms, applications, and recent breakthroughs. The research delves into the many uses of e-nose, such as food quality control, environmental monitoring, medical diagnostics, and industrial operations. It also covers the problems and potential future applications of electronic nose technology. The literature review highlights the importance of this technology in improving our capacity to evaluate complex scents in several domains.

In areas where conventional fundus cameras are logistically unaffordable, the smartphone-based approach is considered as a promising future of glaucoma screening due to their affordability and ease-of-use. Optic disc localization is a critical stage during glaucoma screenings. For fundus images captured with standard fundus cameras, the majority of the models available out there can locate the optic disc with satisfactory performance. However, for images that are captured with smartphone-based fundus cameras, the inherent noise and lower quality of the fundus image makes it difficult for models to detect the optic disc region. In this study, we have proposed to utilize YOLOv8n for optic disc localization due to the model’s cutting-edge performance in diverse tasks and its lightweight nature. We have used a public dataset which has 2000 low quality fundus images that are captured using a smartphone-based fundoscopy device. From these, 60% of the data was used for fine-tuning the model, and 25% for testing. By using a confidence of 50% set as threshold, the model was able to detect the optic disc successfully on over 97% of test images with intersection over union of above 0.85. These results highlight the potential of the lightweight YOLOv8n model for deployment on resource-constrained environments, offering a promising performance on accurately localizing the OD and enhancing the feasibility of affordable glaucoma screening on smartphones.

In this computational study, we investigate the electronic properties of zigzag graphene nano-parallelograms (GNPs), which are parallelogram-shaped graphene nanoribbons of various widths and lengths, using thermally-assisted-occupation density functional theory (TAO-DFT). Our calculations reveal a monotonic decrease in the singlet-triplet energy gap as the GNP length increases. The GNPs possess singlet ground states for all the cases examined. With the increase of GNP length, the vertical ionization potential and fundamental gap decrease monotonically, while the vertical electron affinity increases monotonically. Besides, as the GNP length increases, the symmetrized von Neumann entropy increases monotonically, denoting an increase in the degree of multi-reference character associated with ground-state GNPs. The occupation numbers and real-space representation of active orbitals indicate that there is a transition from the nonradical nature of the shorter GNPs to the increasing polyradical nature of the longer GNPs. In addition, the edge/corner localization of active orbitals is found for the wider and longer GNPs.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

Polyanilines are a class of conductive polymers that have attracted significant interest in the field of organic electronics due to their unique properties. In this article, the fluorescence spectroscopy and photovoltaic properties of polyaniline-based thin films and copolymers are investigated. The study focuses on understanding the relationship between the composition and structure of polyanilines and their optical and electrical properties. The article discusses the results of experiments on the photoluminescent properties of S1-S9 copolymers in a DMSO solution and of thin-film photoresistors based on polyanilines. The findings reveal that the photovoltaic properties of the thin films depend on the conditions of their fabrication and their surface morphology. The solubility of polyanilines is excellent, making the production of electronic components compatible with modern printing technologies in organic electronics. The work also points out that the photoconductivity of polyanilines can be improved by incorporation of additional molecular groups into the polymer matrix. Overall, this study sheds light on the potential of polyanilines as promising materials for organic electronics and provides insights into how their properties can be optimized for specific applications.

Advances in biomimetic triboelectric nanogenerators (TENGs) have significant implications for electronic skin (e-skin) and human-machine interaction (HMI). Emphasizing the need to mimic complex functionalities of natural systems, particularly human skin, TENGs leverage triboelectricity and electrostatic induction to bridge the gap in traditional electronic devices' responsiveness and adaptability. The exploration begins with an overview of TENGs' operational principles and modes, transitioning into structural and material biomimicry inspired by plant and animal models, proteins, fibers, and hydrogels. Key applications in tactile sensing, motion sensing, and intelligent control within e-skins and HMI systems are highlighted, showcasing TENGs' potential in revolutionizing wearable technologies and robotic systems. This review also addresses the challenges in performance enhancement, scalability, and system integration of TENGs. It points to future research directions, including optimizing energy conversion efficiency, discovering new materials, and employing micro-nanostructuring techniques for enhanced triboelectric charges and energy conversion. The scalability and cost-effectiveness of TENG production, pivotal for mainstream application, are discussed along with the need for versatile integration with various electronic systems. The review underlines the significance of making bioinspired TENGs more accessible and applicable in everyday technology, focusing on compatibility, user comfort, and durability. Conclusively, it underscores the role of bioinspired TENGs in advancing wearable technology and interactive systems, indicating a bright future for these innovations in practical applications.

Abstract Introduction: An important indicator of a hospital's quality of care is the frequency of visits to the emergency department (ED). If a patient returns to the emergency room (ED) shortly after being evaluated or treated, it is generally assumed that their initial evaluation or treatment was inadequate. Objectives: The purpose of this study is to identify the main reasons for patient revisits to the emergency department in Hail. Studies suggest that researchers usually report the reasons for revisiting patients after 72 hours to patients themself. Therefore, alternative hypotheses will attribute the reasons to the system or physician's skill. To test these hypotheses, a methodology was developed. Method: The study analyzed patients discharged from King Khalid Hospital within 72 hours of discharge, involving all adults, regardless of health status or location Results: In February 2019, 17461 ED visits occurred, with 11% returning within 72 hours. In February 2022, 880 of 8749 visits resulted in a 10% return visit, with 30 randomly selected return visits.Conclusion: Increased community awareness post-COVID-19 may explain differences in ED revisit rates between 2022 and 2019, with system errors and patient information re-entry being associated

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

Background: Patients with infectious complications related to the presence of cardiac implantable electronic devices (CIED) constitute a heterogeneous group, including local pocket infection (PI) and lead related infectious endocarditis (LRIE). The diagnosis of CIED-related infection is often difficult and requires complex imaging and microbiological tests. The aim of the current study was to evaluate the usefulness of new simple hematological parameters in detecting infectious complications in patients with CIED and assessing their extent. Methods: The retrospective analysis of clinical data of 2909 patients (36.37% with CIED-related infections), undergoing transvenous lead extraction (TLE) procedures in three high-volume centres in the years 2006-2020, was conducted. The sensitivity and specificity of new hematological markers were evaluated: the neutrophil to lymphocyte ratio (NLR), neutrophil to platelet ratio (NPR), and lymphocyte to platelet ratio (LPR) in the diagnosis of infectious complications, assessment of the spread of the infectious process and differentiation of additional structures related to the presence of leads. Results: In patients with CIED infections, compared to the non-infectious group, high inflammatory parameters were confirmed, and the highest specificity of the new markers in detecting the infectious process was demonstrated. (79.47% for NPR and 72.82% for NLR). Analysis of laboratory parameters in infectious and non-infectious patients with the presence of additional lead-related masses showed the highest specificity of NPR (82,78%) in predicting the diagnosis of vegetation. Comparison of laboratory parameters in patients with LRIE and PI showed higher NLR % (4.24 vs 2.56; p<0.001, area under curve (AUC) in a receiver operating characteristic (ROC) curve: 0.67 and 0.78 respectively) and higher NPR (0.03 vs 0.02; p<0.001; AUC: 0,51 and 0,55) in patients with LRIE. The highest sensitivity in the detection of coexistence LRIE with PI has been demonstrated for NLR (87.33%). Conclusions: Novel hematological markers may be helpful in the recognition of the inflammatory process in patients with CIED, differentiation of vegetation and vegetation-like masses, and the extent of infection in patients with PI.

Although multiple sclerosis (MS) is an inflammatory demyelinating disease of the central nervous system (CNS) that results in many neurological disabilities, optic neuritis (ON) is developed in some MS patients. However, the molecular mechanism of ON remains unknown. Galectins, β-galactoside-binding lectins, are involved in various pathophysiology. We have previously shown that galectin-3 (gal-3) is associated with the pathogenesis of experimental autoimmune encephalomyelitis (EAE), its animal model for human MS. In the current study, the expression of gal-3 was explored in the visual pathway of the EAE mice to clarify the pathogenesis of ON. Immunohistochemical analysis demonstrated that expression of gal-3 was increased in the visual pathway of the EAE mice during the peak disease, compared with naïve and EAE mice during the chronic disease. Expression of gal-3 was observed in mainly microglia/macrophages and astrocytes in the visual pathway of the EAE mice. In addition, gal-3+Iba-1+ cells with the phagocytic activities reflected by immunostaining with cathepsin-D were accumulated at demyelinating lesions in the visual pathway during peak disease of EAE. Moreover, NLRP3 expression was also detected in most gal-3+Iba-1+ cells. These results indicate a considerable possibility that gal-3 regulates the NLRP3 signaling in microglia/macrophages, followed by neuroinflammatory demyelination in ON. By contrast, astrocytic expression of gal-3 was also observed from the peak to the chronic disease. Taken together, the current study suggests a critical role of gal-3 in the pathogenesis of ON and proposes gal-3 in glial cells as a potential therapeutic target for ON.

The work carried out first-principles calculations within the framework of density functional theory to study the structural stability of the CsSnI₃ compound and the influence of phase transitions on their electronic and optical properties. Using the GGA and SCAN functionals, the relaxed structures of the CsSnI₃ phases were obtained and their geometric characteristics were assessed. Using the Phonopy code based on VASP, calculations of phonon and thermodynamic properties were performed, and the temperatures of phase transitions of CsSnI₃ were determined. The temperature dependences of the thermodynamic parameters α-, β-, γ- and δ-phases of CsSnI₃ were analyzed. The trends in free energy, entropy, enthalpy, heat of formation energy and heat capacity were justified in terms of the pattern of changes in the total energy of the four phases of CsSnI₃ from VASP calculations. It is shown that at 0 K the non-perovskite structure of the CsSnI₃ compound (δ-CsSnI₃) is the most stable (followed by γ-CsSnI₃), and the tetragonal phase (β) is quite unstable, having the highest energy among the perovskite phases. It was revealed that at temperatures above 450 K the tetragonal phase becomes stable, and when the temperature drops, it transforms into the cubic phase (α-CsSnI₃). The phase transition between the β and γ phase of perovskite occurs in the range of 300-320 K, and at 320 K a black-yellow transformation of CsSnI₃ occurs in which the cubic phase (black perovskite) undergoes a phase transition to a non-perovskite conformation (yellow phase). The presence of temperature phase transitions between two orthorhombic phases of CsSnI₃ at 360 K was discovered, although direct transitions of the α⟷γ and γ⟷δ types have not yet been reported in any experiment, except for γ→δ transitions under the influence of moisture. Based on well-relaxed structures (from the SCAN calculations), the band gap widths for four CsSnI₃ phases were calculated and compared with experimental measurements. Electronic properties and Fermi level shifts as a result of phase transformations of CsSnI₃ were assessed using the HSE06 functional and machine learning prediction. The values of the complex dielectric constant and the refractive index of all phases of the CsSnI₃ were determined.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

The contemporary landscape of eHealth is characterized by major concerns related to electronic medical records (EMRs). In an EMR, critical patient health information gets its own repository, which is the core of the eHealth system. Notably, the EMR not only retrieves health information generated in ambulatory clinical settings but also includes court-generated records. These overlapping records assume the role of a foundational data source for a comprehensive electronic health record (EHR). This scholarly review sheds light on recent trends in medical records and associated challenges, while at the same time providing insights into Saudi Arabia’s targeted approaches to healthcare delivery. Additionally, the talk expands to include a description of blockchain technology and its underlying conceptual framework. This demonstration positions blockchain technology as a promising approach that requires consideration for future use in the healthcare system.

For a fiber optic gyroscope, thermal deformation of the fiber coil can introduce additional ther-mal-induced phase errors, commonly referred to as thermal errors. Thermal error compensation techniques are effective means of addressing this issue. The principle behind these techniques involves real-time sensing of thermal errors and correcting them within the output signal. Since it is challenging to directly separate thermal errors from the output signal of the fiber optic gyro-scope, it is necessary to predict thermal errors based on temperature. To establish a mathematical model between temperature and thermal errors, this paper measured synchronized data of phase errors and angular velocity for the fiber coil under different temperature conditions and aimed to model it using data-driven methods. Due to the difficulty of conducting tests and the limited number of data samples, an algorithm called TD-model modeling is proposed to address the issue of overfitting, which can reduce the model's generalization ability. First, a theoretical analysis of the phase errors caused by thermal deformation of the fiber coil is performed. Subsequently, the critical parameters, such as the thermal expansion coefficient, are determined, and a theoretical model is established. Finally, the theoretical analysis model is incorporated as a regularization term and combined with the test data to jointly participate in the regression of model coefficients. Through experimental comparative analysis, it is shown that, relative to ordinary regression models, the TD-model effectively mitigates overfitting caused by the limited number of samples, leading to a 58% improvement in predictive accuracy.

The utilization and engineering of thermo-optic effects have found broad applications in integrated photonic devices, facilitating efficient light manipulation to achieve various functionalities. Here, we perform both an experimental characterization and theoretical analysis of these effects in integrated micro-ring resonators in high index doped silica (HIDS), which has had many applications in integrated photonics and nonlinear optics. By fitting the experimental results with theory, we obtain fundamental parameters that characterize their thermo-optic performance, including the thermo-optic coefficient, the efficiency for the optically induced thermo-optic process, and the thermal conductivity. The characteristics of these parameters are compared to those of other materials commonly used for integrated photonic platforms, such as silicon, silicon nitride, and silica. These results offer a comprehensive insight into the thermo-optic properties of HIDS based devices. Understanding these properties is essential for efficiently controlling and engineering them in many practical applications.

A systematic and comprehensive review of critical applications of Blockchain Technol-ogy with Differential Privacy integration lies within the privacy and security enhancement. This paper aims to highlight the research issues in the e-health domain (e.g., Electronic Medical Rec-ords) and to review the current research directions in Differential Privacy integration with Blockchain Technology.(1) Background: The current state of the art in the e-health domain is identified as follows: (a) healthcare information poses a high level of security and privacy concerns due to its sensitivity; (b) due to vulnerabilities surrounding the healthcare system, a data breach is common and presents a risk for attacks by an adversary; and (c) the current privacy and security apparatus needs further fortification. (2) Methods: The methodology uses a systematic literature review (SLR) to identify and select relevant research papers and academic journals in DP and BT. (3) Results: The results are categorized into: e-Health Record Privacy, Real-Time Health Data, and Health Survey Data Protection to identify inherent issues with Differential Privacy integra-tion with Blockchain and technical challenges.(4) Conclusion: This review thoroughly surveyed and summarized Differential Privacy mechanisms in EMR privacy, real-time health data, and health survey data protection while highlighting challenges.

(1) Background: Newer generation ophthalmologists practicing in the developed world are not very familiar with some tropical ocular diseases due to the absence of reports in the ophthalmic literature over the past thirty years. Because of world globalization or due to influx of immigrants from Sub Saharan Africa, exotic retinal diseases are being encountered more often in ophthalmology clinics; (2) Methods: Case series of chorioretinitis or optic neuritis with obscure etiology; (3) Results: 4 cases qualified with the diagnosis of ocular onchocerciasis based on their residence near fast rivers in endemic areas, multimodal imaging, long term follow-up showing progressive disease and negative workup for other diseases. Characteristic findings include peripapillary choroiditis with optic neuritis or atrophy, subretinal tracts of the microfilaria, progressive RPE atrophy around heavily pigmented multifocal chorioretinal lesions of varying shapes and subretinal white or crystalline dots. Typical skin findings are often absent in eyes with chorioretinitis rendering the diagnosis more challenging; (4) Conclusions: Familiarity with the myriad ocular findings of onchocerciasis, and a high degree of suspicion in subjects residing in endemic areas can help in the correct diagnosis and implementation of appropriate chemotherapy. Onchocercid chorioretinitis is a slow insiduous progressive and prolonged polymorphous disease.

Taiwan’s Chi Mei Medical Center has a vision of becoming a sustainable organization. They found they violated the sustainable development goal (SDG) 13 (“Climate Action”) since its workflows consume excessive tangible resources and waste much operation time. To fulfill the vision, the Chi Mei Medical Center first introduced electronic invoicing. Implementing this electronic invoicing included adopting cloud E-invoice data and creating a software robot for auditing them. This study presents this software robot and its contributions. The software robot replaces an internal auditor to log into Taiwan’s E-invoice platform, download cloud E-invoice data, and detect the inconsistency between these cloud and on-premise data. Internal auditors of the Chi Mei Medical Center only needed to confirm the detection results. They welcome this software robot since it significantly reduces their work burdens. They approved more software robots for assisting other workflows. Besides, the Chi Mei Medical Center earned profits after eliminating paper invoices. This elimination helped release less carbon. This study concludes that chasing a sustainable organization is unnecessarily equivalent to the requirement of more costs. A software robot represents the last puzzle for constructing a paperless workflow since it can resolve the resistance of existing workers to a new workflow.

Optic neuritis (ON) is the most common cause of vision loss in young adults. It manifests as acute or subacute vision loss, often accompanied by retrobulbar discomfort or pain on eye movements. Typical ON is associated with Multiple Sclerosis and is generally mild and steroid-responsive, whereas atypical forms are characterized by unusual features, such as optic disc edema, poor treatment response and bilateral involvement, and are often associated with autoantibodies against aquaporin-4 (AQP4) and Myelin Oligodendrocyte Glycoprotein (MOG). However, in rare cases AQP4 and MOG antibodies will come back negative, plunging the clinician in a diagnostic conundrum. Seronegative ON warrants a broad differential diagnosis, including autoantibody-associated, granulomatous, and systemic disorders. These rare forms need to be identified promptly, as their management and prognosis is greatly different. The scope of this review is to describe possible, rarer etiologies of ON when AQP4 and MOG antibodies are negative and discuss their diagnosis and treatment.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

In the realm of power delivery to end-users, transformers are indispensable, with their malfunctions leading to substantial economic, safety, and environmental repercussions. The need for persistent surveillance is accentuated for in-situ oil-filled transformers, given the potential degradation of oil and the emergence of related ageing by-products. As the focus tilts towards online detection methodologies for transformer oil ageing, bypassing challenges associated with traditional offline methods such as sample contamination and misinterpretation, fiber optic sensors are gaining trac-tion due to their compact nature, cost-effectiveness, and resilience to electromagnetic disturbances typical in high-voltage environments. This work delves into the sensitivity analysis of intensi-ty-modulated plastic optical fiber sensors. The investigation encompasses key determinants such as the influence of optical source wavelengths, noise response dynamics, ramifications of varying sensing lengths, and repeatability assessments. Findings underscore that elongating the sensing length detrimentally affects both the linearity response and repeatability, largely attributed to the diminished resistance to external noise. Additionally, the choice of the optical source wavelength proved to be a critical variable in assessing sensor sensitivity.

To study and monitor the adverse health consequences from using electronic cigarettes, a user’s puff topography, which are quantification parameters of the user’s vaping habits, plays a central role. In this work, we introduce a topography sensor to measure the mass of total particulate matter generated in every puff and to estimate the nicotine yield. The sensor is compact and low-cost, and is integrated into the electronic cigarette device to promptly and conveniently monitor the user’s daily puff topography. The topography sensor is comprised of a photometric sensor and a pressure sensor. The photometric sensor measures the mass concentration of the aerosol, based on scattering of near-infrared light from airborne particles, while the pressure sensor measures the flow rate. The topography sensor was experimented under various conditions with a wide range of atomizer power, puff duration, and inhalation pressure. The sensor’s accuracy was validated by comparing the sensor’s readings with reference measurements, and the results matched closely with the trends reported by existing studies on electronic cigarettes. An example application of tracking a user’s puff topography was also demonstrated. Our topography sensor holds great promise in mitigating health risks of vaping, and in promoting quality control of electronic cigarette products.

Background: Although electronic health records (EHR) provide useful insights into disease patterns and patient treatment optimisation, their reliance on unstructured data presents a difficulty. Because of their narrative structure, echocardiography reports, which provide extensive pathology information for cardiovascular patients, are particularly challenging to extract and analyse. Although natural language processing (NLP) has been utilised successfully in a variety of medical fields, it is not commonly used in echocardiography analysis. Objectives: To develop an NLP-based approach for extracting and categorizing data from echocardiography reports by accurately converting continuous (e.g. LVOT VTI, AV VTI, and TR Vmax) and discrete (e.g. Regurgitation severity) outcomes in semi-structured narrative format into structured and categorized format, allowing for future research or clinical use. Methods: 135,062 Trans-Thoracic Echocardiogram (TTE) reports were derived from 146967 baseline Echocardiogram reports and split into three cohorts: Training and Validation (n = 1075), Test Dataset (n = 98) and Application Dataset (n = 133,889). The NLP system was developed and iteratively refined using medical expert knowledge. The system was used to curate a moderate-fidelity database from extractions of 133,889 reports. A hold-out validation set of 98 reports was blindly annotated and extracted by two clinicians for comparison with the NLP extraction. Agreement, discrimination, accuracy and calibration of outcome measure extractions were evaluated. Results: Continuous outcomes including LVOT VTI, AV VTI, and TR Vmax exhibited perfect inter-rater reliability using intra-class correlation scores (ICC=1.00, P< 0.05) alongside high R2 values, demonstrating an ideal alignment between the NLP system and clinicians. Good level (ICC =0.75-0.9, P<0.05) of inter-rater reliability were observed for outcomes such as LVOT Diam, Lateral MAPSE, Peak E Velocity, Lateral E' Velocity, PV Vmax, Sinuses of Valsalva, and Ascending Aorta diameters. Furthermore, the accuracy rate for discrete outcome measures was 91.38% in the confusion matrix analysis, indicating effective performance. Conclusions: The NLP-based technique yielded good results when it came to extracting and categorising data from echocardiography reports. The system demonstrated a high degree of agreement and concordance with clinician extractions. This study contributes to the effective use of semi-structured data by providing a useful tool for converting semi-structured text to structured echo report that can be used for data management. Additional validation and implementation in healthcare settings can improve data availability and support research and clinical decision-making.

Background Ultrasonographic measurement of the optic nerve sheath diameter (ONSD) is helpful in the assessment of intracranial pressure. The aim of this study was to determine whether the Trendelenburg position during laparoscopic urological surgery changed the ONSD and whether changes correlated with postoperative complications. Methods In this prospective study, we measured ONSD before patients were placed in the Trendelenburg position. Then the Trendelenburg position was established by tilting the operating table to 20-25 degrees. After surgery, the patients were placed in a horizontal position, and the second measurement of ONSD was obtained. Results The study included 69 patients. The average preoperative ONSD in the right eye was 5.8 ± 0.7 mm and 5.8 ± 0.8 mm in the left eye. The average postoperative ONSD in the right eye was 6.6 ± 0.8 mm and 6.6 ± 0.7 mm in the left eye. The differences between postoperative and preoperative values in the right and left eyes were statistically significant (p <0.000001). ONSD increases above the norm did not correlate with the incidence of postoperative nausea (p = 0.94), delirium (p = 0.81), or the time to patient awakening (p = 0.29). Conclusion ONSD increased in patients who underwent surgical procedures performed in the Trendelenburg position, but the increase did not correlate with postoperative complications.

This paper describes the optimal design of a miniature fiber-optic linear displacement sensor. It is characterized by its ability to measure displacements along a millimetric range with sub-micrometric resolution. The sensor consists of a triangular reflective grating and two fiber-optic probes. The measurement principle of the sensor is presented. The design of the sensor's triangular grating has been geometrically optimized by considering the step angle of the grating to enhance the sensor's resolution. The optimization method revealed a global optimum at which the highest resolution is obtained

Two-dimensional (2D) bismuth oxyhalides (BiOX) have attracted much attention as potential optoelectronic materials. Expecting for their application diversity, we herewith systematically investigate the tunable properties of 2D BiOX by using first principles calculations. Their electronic and optical properties can be modulated by changing the number of monolayers, applying strain, and/or varying the halogen composition. The bandgap shrinks monotonically and approaches the bulk value, the optical absorption coefficient increases, and the absorption spectrum redshifts, as the layer number of 2D BiOX increases. Carrier transport property can be improved by applying tensile strain, and the ability of photocatalytic hydrogen evolution can be obtained by applying compressive strain. General strain engineering will be effective in linearly tune the bandgap of BiOX in a wide strain range. Strain together with halogen composition variation can tune the optical absorption spectrum to be on demand in the range from visible to ultraviolet. It suggests that that 2D BiOX materials have potential serving as tunable novel photodetectors, can be used to improve clean energy techniques, and are prospective in the field of flexible optoelectronics.

Changes in the atomic and electronic structure of silicon carbide 3C-SiC (β-SiC), resulting from lead adsorption, have been studied within the density functional theory. The tests were conducted for three representative surfaces with varying degrees of lead coverage. Results indicate that chemisorption occurs, with the strongest binding, found on the hexagonal surface (111) in interaction with three dangling bonds. The adsorption energy rises with increasing coverage, especially as the surface approaches saturation. Analysis of the data was focused on parameters important for corrosion processes such as bond distances, binding energies, Bader charges and charge density difference.

The very slow anodic oxygen evolution reaction (OER) greatly limits the development of large-scale hydrogen production via water electrolysis. By replacing OER with easier urea oxidation reaction (UOR), developing a HER/UOR coupling electrolysis system for hydrogen production can significantly save energy and costs. Al doped cobalt ferrocyanide (Al-Co2Fe(CN)6) nanocube array was in-situ grown on nickel foam (Al-Co2Fe(CN)6/NF). Due to the unique nanocube array structure and regulated electronic structure of Al-Co2Fe(CN)6, the as-prepared Al-Co2Fe(CN)6/NF electrode exhibited outstanding catalytic activities and long-term stability to both UOR and HER. The Al-Co2Fe(CN)6/NF electrode needed potentials of 0.169 V and 1.118 V (vs. reversible hydrogen electrode) to drive 10 mA cm−2 for HER and UOR, respectively, in alkaline condition. Applying the Al-Co2Fe(CN)6/NF to a whole urea electrolysis system, 10 mA cm−2 was achieved at a cell voltage of 1.357 V, which saved 60% electricity energy comparing to that of tranditional water splitting. Density functional theory calculations demonstrated that the boosted UOR activity comes from Co sites with Al doped electronic environments. This promoted and balanced the adsorption/desorption of main intermediates in UOR process. This work indicates that Co based materials as efficient catalysts have great prospects for application in urea electrolysis systems, and are expected to achieve low-cost and energy-saving H2 production.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

A full potential all-electron density functional method within generalized gradient approximation is used to investigate the electronic, elastic and transport properties of cubic copper sulphide and copper selenide. The electronic structure suggests metallic behavior with a zero energy band gap for both materials. Elastic property calculations suggest a stiff material with the bulk to shear modulus ratio of 0.35 and 0.44 for Cu2S and Cu2Se respectively. The transport properties were estimated using the Boltzmann transport approach. Seebeck coefficient, electrical conductivity, thermal conductivity, and power factor all suggest a potential p-type conductivity for Cu2S and n-type conductivity for Cu2Se.

The Internet of Things (IoT) was born from the fusion of virtual and physical space and became the initiator of many scientific fields. Economic sustainability is the key to further development and progress. Today, the need for electronic commerce has become an economic priority in the transition period between Industry 4.0 and Industry 5.0. Unlike mass production in Industry 4.0, customized production in Industry 5.0 should reach its true potential in vertically organized management and decision-making systems. The authors focused their research on e-commerce based on the three-level vertical IoT environment and the edge, fog, and cloud computing. The paper presents hands-on machine learning (ML) algorithms to facilitate the transition from a flat to a vertical e-commerce concept. The authors also propose practical ML algorithms for a few e-commerce types: consumer-consumer relationships and consumer-company-consumer relationships. These algorithms are mainly composed of convolution neural networks (CNN), natural language understanding (NLU) and sequential pattern mining (SPM), reinforcement learning (RL for agent training), algorithms for clicking on the item prediction, consumer behavior learning, etc. All presented concepts, algorithms, and models are described in detail.

Axonal degeneration resulting from optic nerve damage can lead to the progressive death of retinal ganglion cells (RGCs), culminating in irreversible vision loss. We contrasted two methods for inducing optic nerve damage: optic nerve compression (ONCo) and optic nerve crush (ONCr). These were assessed for their respective merits in simulating traumatic optic neuropathies and neurodegeneration. We also administered neural progenitor cells (NPCs) into the subtenon space to validate their potential in mitigating optic nerve damage. Our findings indicate that both ONCo and ONCr successfully induced optic nerve damage, as shown by increased ischemia and expression of genes linked to neuronal regeneration. Post NPCs injection, recovery in the expression of neuronal regeneration-related genes was more pronounced in the ONCo model than in the ONCr model, while inflammation-related gene expression saw a better recovery in ONCr. In addition, proteomic analysis of R28 cells in hypoxic conditions identified Vps35 and Syntaxin12 genes. Vps35 preserved mitochondrial function in ONCo, while Syntaxin12 appeared to restrain inflammation via the Wnt/β-catenin signaling pathway in ONCr. NPCs managed to restore damaged RGCs by elevating neuroprotection factors and controlling inflammation through mitochondrial homeostasis and Wnt/β-catenin signaling in hypoxia-injured R28 cells and in both animal models. Our results suggest that ischemic injury and crush injury cause optic nerve damage via different mechanisms, which can be effectively simulated using ONCo and ONCr, respectively. Moreover, cell-based therapies such as NPCs may offer promising avenues for treating various optic neuropathies, including ischemic and crush injuries.

The idealized rhombohedral unit cell of boron carbide is formed by a 12-atom icosahedron and a 3-atom linear chain. Phase transitions are second order and caused by the exchange of B and C sites or by vacancies in the structure. Nevertheless, the impact of such minimal structural changes on the properties can be significant. As the X-ray scattering cross sections of B and C atoms are very similar, the capability of X-ray fine structure investigation is restricted. Phonon spectroscopy helps closing this gap. Phase transitions known to date have been identified due to significant changes of properties: (1) The phase transition near the chemical composition B8C by clear change of the electronic structure; (2) The endothermic temperature-dependent phase transition at 712 K by the according change of specific heat; (3) The high-pressure phase transition at 33.2 GPa by the drastic change of optical appearance from opacity to transparency. These phase transitions affect IR- and Raman-active phonons and other solid-state properties. The phase transitions at B~8C and 712 K mean that a well-defined distorted structure is converted into another one each. In the high-pressure phase transition, an apparently well-defined distorted structure changes into a highly ordered one. In all these cases, the distribution of polar C atoms in the icosahedra plays a crucial role.

Ants have a very sophisticated olfactory system; their communication is based on the interpretation of chemical trails known as semiochemicals. The escamolera ant (Liometopum apiculatum), has behaviors and physiological responses is induced by semiochemicals, without however, these have not been studied. Using an electronic nose analysis (e-nose) and chromatographic techniques, semiochemicals of L. apiculatum in nests, foraging trails and dissected the gasters were evaluated. Data were analyzed with multivariate statistics and a logistic regression model based on predictors (ant counts) and the semiochemicals identified in pre-season (PRE), season (TEM) and post-season (POS) of larval collecting. From the general pattern of volatiles with a natural separation in POS and a partial distribution between PRE and TEM 32 semiochemicals were identified inside the nests, those who can induce the behavioral responses of trail-following, alarm, aggression, and nestmate recognition. Trail counts indicated that ant traffic was higher in POS and that the presence of certain semiochemicals (response variable) have good fit in the model regression. These findings are intended to provide useful information and support decision-making for the conservation and sustainable use of L. apiculatum in central Mexico.

Background We aimed to compare the retinal, optic disc vascular density (ODVD) values, and acircularity index (AI) of patients with idiopathic macular telangiectasia type 2 (IMT) and healthy individuals using the optical coherence tomography angiography(OCTA) device. Methods The study included 39 patients with IMT and 37 healthy controls. The OCTA findings of the patients and controls were examined. Results The total, parafoveal and perifoveal vascular density of the superficial capillary plexus, choriocapillaris blood flow, inside-disc ODVD, retinal nerve fiber layer (RNFL), and retinal thicknesses were found to be statistically significantly lower and the foveal avascular zone value was statistically significantly higher in the IMT group compared to the control group (p=0.001, p=0.01, p=0.02, p=0.01, p=0.009, p=0.002, p=0.02, respectively).There was a statistically significant negative correlation between best-corrected visual acuity (BCVA) and AI (p=0.02), a statistically significant positive correlation between peripapillary vascular density and BCVA(p=0.04). Conclusion We consider that the lower retinal, choriocapillaris, and ODVD values, retinal and RNFL thicknesses in the patients with IMT compared to the controls were due to vascular damage, remodeling, fibrosis, proliferation, and Müller cell damage. Ellipsoid zone defect, AI, and peripapillary vascular density are important indicators in the evaluation of visual acuity in these patients.

TmMgB5O10 spontaneous crystals were synthesized via flux-growth technique from a K2Mo3O10-based solvent. The crystal structure of the compound was solved and refined within the space group P21/n. The first principles calculations of the electronic structure reveal that TmMg-pentaborate is an insulator with an indirect energy band gap of approximately 6.37 eV. Differential scanning calorimetry measurements and powder X-ray diffraction studies of heat-treated solids show that TmMgB5O10 is an incongruent melting compound. A characteristic band of Tm3+ cation corresponding to the 3H6 → 1D2 transition is observed in the photoluminescence excitation spectra of TmMg-borate. The as-obtained crystals exhibit intense blue emission with the emission peaks centered at 455, 479, 667 and 753 nm. The most intensive band corresponds to the 1D2 3F4 transition.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode~2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

The calibration of length is related to the national economy and people's livelihood. The traditional calibration of length value was sent the uncalibrated instrument to the laboratory and the intrinsic error of the tested instrument was obtained in the laboratory. However, calibrating the instrument in the site produced additional error. In this article, a remote calibration method of length measurement based on optical fiber information transmission following with a proof of principle system was studied to reduce the additional error. The 1.0-level displacement guide rail was calibrated according to this method. The results showed that the relative error of guide rail displacement under different lengths was within 0.6%. The expanded uncertainties of 10 μm, 100 μm and 1 mm were analyzed respectively. The calibration results meet the actual standards of the guide rail. This optical method is a good candidate for remote calibration.

In a previous paper, we solved the partial differential equation of Mullins problem in the case of the evaporation-condensation in electronic devices and gave an exact solution relative to the geometric profile of the grain boundary grooving when materials are submitted to thermal and mechanical solicitation and fatigue effect. In this new research, new modelling of the grain groove profile was proposed and new analytical expressions of the groove profile, the derivative and the groove depth were obtained in the case of diffusion in thin polycrystalline films by the resolution of the fourth differential equation formulated by Mullins that supposed 〖y'〗^2≪1. The obtained analytical solution gave more accurate information on the geometric characteristics of the groove that were necessary to study the depth and the width of the groove. These new findings will open a new way to study with more accuracy the problem of the evaporation-condensation combined to the diffusion phenomenon on the material surfaces with the help of the analytical solutions.

The time-resolved CIDNP method can provide information about degenerate exchange reactions (DEE) involving short-lived radicals. In the temperature range from 8 to 65°C, the DEE reactions of the guanosine-5’-monophosphate anion GMP(-H)- with the neutral radical GMP(-H)•, of the N-acetyl tyrosine anion NacTyrO- with a neutral radical NacTyrO• and of the tyrosine anion TyrO- with a neutral radical TyrO• were studied. In all the studied cases, the radicals were formed in the reaction of quenching triplet 2,2’-dipyridyl. The reorganization energies were obtained from Arrhenius plots. The rate constant of the reductive electron-transfer reaction in pair GMP(-H)•/TyrO- was determined at T = 25°C. Rate constants of GMP(-H)• radical reduction reactions with TyrO- and NacTyrO- anions calculated by the Marcus cross relation differ from the experimental ones by two orders of magnitude. The rate constants of several other electron transfer reactions involving GMP(-H)-/•, NacTyrO-/•, and TyrO-/• pairs calculated by cross relation agree well with the experimental values. The rate of nuclear paramagnetic relaxation was found for the 3,5 and β-protons TyrO• and NacTyrO•, the 8-proton GMP(-H)• the 3,4-protons DPH• at each temperature. In all cases, the dependences of the rate of nuclear paramagnetic relaxation on temperature are described by the Arrhenius dependence.

The Covid-19 pandemic has forced the transfer of local government public ser-vices to the virtual world. Remote handling of matters in government offices has be-come the norm rather than the exception. The 2016 EU directive on public sector web-sites and mobile applications and the 2019 European Digital Accessibility Act made it mandatory that these services be provided electronically and accessible to people with disabilities. The purpose of the study conducted by the authors was to determine whether the Covid-19 pandemic resulted in the implementation of European solutions in the Polish legal order and whether this implementation resulted in the actual adap-tation of digital activities of local government units (LGUs) to the needs of people with disabilities. The research was conducted in Q4 2022 in two trial formats: 1. In the form of a survey (about 250 LGUs), which covered compliance with for-mal requirements, the level of readiness of the officials to create digitally accessible documents and content, and organizational readiness of the offices. 2. In the form of an analysis of the source code of the websites of 66 Polish cities with county rights - due to the availability of results of the same sample from 2015. The completed research showed that the LGUs in Poland: 1. met the formal and organizational requirements for digital accessibility, 2. did not make the necessary efforts to prepare employees to create digitally ac-cessible documents and content, 3. the surveyed websites had inferior source code in terms of meeting the WCAG standard in 2022 than in 2015. It seems reasonable to conclude that the Covid-19 pandemic had a formal, rather than real, impact on the digital accessibility of services provided by Polish LGUs.

The analysis of the 2002 Prestige tanker accident showed how public misinformation can worsen marine pollution incidents, rendering their management suboptimal as these evolve, raising thus the issue of appropriately informing and educating coastal and island populations at risk. Two decades later, developments in electronic platforms, Geographic Information Systems (GIS), in Automatic Identification System (AIS) for ship signal transmission, and in social media, provide a set of means for public monitoring of such incidents, creating the possibility to antagonize effec-tively erroneous, or malevolent information which can hinder efficient actions for containing ma-rine pollution risks even without active training of populations concerned. The authors, in the framework of development of the Marine Coastal Observatory and Risk Management project “AEGIS+”, have developed E-S.A.V.E., an online platform which: a) meets the needs of different users as revealed by a survey run across groups of them, b) uses a suitable Geographic Infor-mation Systems (GIS) environment, c) cooperates with public authorities, for the reliable update of automated systems, and d) employs an artificial intelligence (AI) supported tool for social me-dia monitoring; the platform also provides educational and information national and interna-tional resources on marine environmental protection and sustainable maritime logistics.

Accurate localization of the fovea in fundus images is essential for diagnosing retinal diseases. Existing methods often require extensive data and complex processes to achieve high accuracy, posing challenges for practical implementation. In this paper, we propose an effective and efficient approach for fovea detection using simple image processing operations and a geometric approach based on the optical disc's position. A key contribution of this study is the successful determination of the temporal direction by leveraging readable asymmetries related to the optical disc and its surroundings. We discuss three methods based on asymmetry conditions, including blood vessel distribution, cup disc inclination, and optic disc location ratio, for detecting the temporal direction. This enables precise determination of the optimal foveal region of interest (ROI). Through this optimized fovea region, fovea detection is achieved using straightforward morphological and image processing operations. Extensive testing on popular datasets (DRIVE, DiaretDB1, and Messidor) demonstrates outstanding accuracy of 99.04% and a rapid execution time of 0.251 seconds per image. The utilization of asymmetrical conditions for temporal direction detection provides a significant advantage, offering high accuracy and efficiency while competing with existing methods.

Glaucoma, a group of diseases characterized by progressive retinal ganglion cell loss, cupping of the optic disc and by a typical pattern of visual field defects, is a leading cause of severe visual impairment and blindness worldwide. Elevated intraocular pressure (IOP) is the leading risk factor for glaucoma development. However, glaucoma can also develop at normal pressure levels. An increased susceptibility of retinal ganglion cells to IOP, systemic vascular dysregulation, endothelial dysfunction and autoimmune imbalances have been suggested to play a role in the pathophysiology of normal tension glaucoma. Since inflammation and oxidative stress play a role in all forms of glaucoma, the goal of this review article is to resent an overview on the inflammatory and prooxidant mechanisms in the pathophysiology of glaucoma and to discuss immunomodulatory and antioxidant treatment approaches.

Ethylene is an ideal CO2 product in an electrocatalytic CO2 reduction reaction (CO2RR), which has high economic value. In this paper, Al–doped octahedral Cu2O (Al–Cu2O) catalyst was synthesized by a simple wet chemical method. The selectivity of CO2RR products was improved by doping Al onto the surface of octahedral Cu2O by regulating the Al content. The Al–Cu2O was used as an efficient electrocatalyst for CO2RR with selective ethylene production. The Al–Cu2O exhibited a high Faradic efficiency (FEC2H4) of 44.9% at -1.23 V (vs. RHE) in CO2 saturated 0.1 M KHCO3 electrolyte. Charge transferring from Al atom to Cu atom take place after Al doping in Cu2O, thereby optimizing the electronic structure, which facilitates CO2RR to ethylene production. The DFT calculation showed that the Al–Cu2O catalyst can effectively reduce the adsorption energy of the *CHCOH intermediate and promote the mass transfer of charges, thus improving the FEC2H4. After Al doping into Cu2O, the center of d orbitals shift positively, which makes the d–band closer to the Fermi level. Furthermore, the density of electronic states increases, which was conducted to the interaction between Cu atoms and intermediates, thus accelerating the electrochemical CO2 reduction process. This work proved that the metal doping strategy can effectively improve the catalytic properties of Cu2O, thus providing a useful way for CO2 cycling and green production of C2H4.

— Printing electronics incorporates several significant technologies, such as semiconductor devices produced by various printing techniques on flexible substrates. With growing interest in printed electronic devices, new technologies have been developed to make novel devices with inexpensive and large-area printing techniques. This review article focuses on the most recent developments in printed photonic devices. Photonics and optoelectronic systems may now be built utilizing materials with specific optical properties and 3D designs achieved through additive printing. Optical and architected materials that can be printed in their entirety are among the most promising future research topics, as are platforms for multi-material processing and printing technologies that can print enormous volumes at high resolution while also maintaining high throughput. Significant advances in innovative printable materials create new opportunities for functional devices to act efficiently, such as wearable sensors, integrated optoelectronics, and consumer electronics. This article provides an overview of printable materials, printing methods, and uses of printed electronic devices.

The process of building microgrids on top of existing passive distribution networks warrants a multi-criteria analysis. Besides the calculation of investment outlays needed for the modernization of distribution networks, such an analysis covers an assessment of the technological and economic effects of building microgrids. The resulting effects depend on the topology and configuration of distribution networks, specific microgrid features, the choice of current type for the entire microgrid or its individual parts, the ways of connecting distributed energy resources (DER), the availability and condition of information and communications technology (ICT) infrastructure, and other factors. Complete input data allow one to design an optimal microgrid configuration, but the main technological and economic effects are determined by the algorithms of operation and the parameters setting of the automatic control system (ACS) and the protection system. Known approaches to designing microgrids focus on addressing basic tasks while minimizing investment required for their implementation. The above is fully justified when constructing new microgrids, but building microgrids on top of existing distribution networks, given the uniqueness of their topology and configuration, does not allow the use of standardized solutions. The development of approaches to the design of microgrids under such constraints, with minimized investment for the modernization of existing distribution networks, is an urgent task. The use of different types of current for microgrid segments determines the choice of particular ACS and protection system, which depends on the availability of information and communications technology infrastructure. This article contributes a review of approaches to designing AC and AC-DC microgrids to maximize their technological and economic effects. We review techniques for analyzing existing distribution networks aimed at choosing the type of current for the entire microgrid or its individual parts, the optimal connection points of microgrids to distribution networks, the mix and capacity of DERs, with such choices informed by the condition of switching devices and information and communications technology infrastructure. The article presents the results of the analysis of approaches to choosing the optimal configuration of microgrids, microgrid ACS and protection system, with an evaluation of the technological and economic effects subject to minimization of investment for the modernization of existing distribution networks.

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

Optic nerve disorders encompass a wide spectrum of conditions characterized by the loss of retinal ganglion cells (RGCs) and subsequent degeneration of the optic nerve. The etiology of these disorders can vary significantly, but emerging research highlights the crucial role of oxidative stress, an imbalance in the redox status characterized by an excess of reactive oxygen species (ROS), in driving cell death through apoptosis, autophagy, and inflammation. This review provides an overview of ROS-related processes underlying four extensively studied optic nerve diseases: glaucoma, Leber's hereditary optic neuropathy (LHON), anterior ischemic optic neuropathy (AION), and optic neuritis (ON). Furthermore, we present preclinical findings on antioxidants, with the objective of evaluating the potential therapeutic benefits of targeting oxidative stress in the treatment of optic neuropathies.

The study aimed to identify clinical pharmacology patterns of prescribed and taken medications in older cardiovascular patients using electronic health records (EHRs) (n = 704) (2019–2022). Medscape Drug Interaction Checker was used to identify pairwise drug-drug interactions (DDIs). Prevalence rates of DDIs were 73.5% and 68.5% among taken and prescribed drugs, respectively. However, total number of DDIs was significantly higher among prescribed medications compared with the list of taken drugs (p < 0.05). Serious DDIs comprised 16% and 7% of all DDIs among prescribed and taken medications, correspondingly (p < 0.05). Median DDI numbers between prescribed versus taken medications were Me = 2, IQR 0-7 and Me = 3, IQR 0-7 per record, respectively. Prevalence of polypharmacy was significantly higher among prescribed medications compared with taken medications (p < 0.05). Women were taking significantly more drugs and had higher rates of polypharmacy and DDIs (p < 0.05). No sex-related differences were observed in the list of prescribed medications. ICD code U07.1 (COVID-19, virus identified) was associated with the highest median DDI number per record. Further research is warranted to improve EHR structure, patient engagement in reporting adverse drug reactions, and genetic profiling of patients to avoid potentially serious DDIs.

This paper presents a method of fusion of identification (attribute) information provided by two types of sensors: combined primary and secondary (IFF) surveillance radars and ESM (Electronic Support Measures). In the first section, the basic taxonomy of attribute identification is adopted in accordance with the standards of STANAG 1241 ed. 5 and STANAG 1241 ed. 6 (draft). These standards provide the following basic values of the attribute identifications: FRIEND, HOSTILE, NEUTRAL, UNKNOWN and additional values: ASSUMED FRIEND and SUSPECT. The basis of theoretical considerations is Dezert-Smarandache theory (DSmT) of inference. The paper presents and practically uses for combining identification information from different ESM sensors and radars six information fusion rules proposed by DSmT - the Proportional Conflict Redistribution rules (PCR1, PCR2, PCR3, PCR4, PCR5 and PCR6). In the paper, rules of determining attribute information by ESM sensor equipped with the data base of radar emitters are presented. It was proposed that each signal vector sent by the ESM sensor contained an extension specifying a randomized identification declaration (hypothesis) - basic belief assignment (BBA). The paper also presents a model for determining the basic belief assignment for a combined primary and secondary radar. Results of the PCR rules of sensor information combining for different scenarios of radio-electronic situation (deterministic and Monte Carlo) are presented in the final part of the paper. They confirm the legitimacy of the use of Dezert-Smarandache theory into information fusion for primary radars, secondary radars and ESM sensors.

In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.

Objective: To quantitatively analyze the production of Doctoral Theses on health issues related to gender in Spain. Method: Quantitative synthesis of the productivity indicators of the Doctoral Theses de-fended in Spanish Universities between 1976 and 2022, obtained from the Spanish TESEO data-base. Descriptive analysis, materialized in tables and graphs, and time series model, based on the Holt-Winters model methodology. Results: 18.75% of the defended Doctoral Theses represents the scientific production of the Universities. Madrid is where the greatest number defend themselves with 37.5%. One in three authors are graduates in medicine. The theme of the Theses is gender violence in 25.0%, the authors are women in 87.5%, 44.0% of women direct theses. The scientific production of directors according to the H Index is very uneven, since one person has an index of 76 and another of 1. The temporal sequence of production is erratic, since in some years no Doctoral Theses are defended, but in 2017 were three. Conclusions: Spanish research in clinical Doctoral Theses on gender is scarce. It would be desirable to develop doctoral programs that promote the generation of theses in health that have gender differences in health care as their central point.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

A number of sustainable and environmental issues are caused by consumer's behavior. Consumers' consumption pattern plays an increasingly important role in environmental conservation and adopting to a more sustainable community. This study used planned behavior theory and structural equation model to quantifies individual purchasing behavior of electronic vehicles based on perceived health risk cased by air pollution in Kunming, China. The findings showed that (1)for residents in Kunming, the perceived air pollution risk, the willingness to purchase new energy vehicles, and actual purchase behavior are low; (2) perception of health risks has a significant positive impact on purchase willingness, behavioral attitude and subjective norms play a significant positive mediating role between perception of health risks and purchase willingness, and perception of behavioral control plays a significant negative role, purchase willingness has significant positive impact on purchase behavior, the direct effect of perceived behavioral control on purchase behavior is insignificant; (3) for highly educated groups, risk controllability has a significant impact on the perception of health risk, subjective norms and behavioral attitude have significant impacts on purchase willingness, while for low-income gourp, risk controllability has significant impacts on the perception of health risk.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

Companion animals are increasingly being recognized as important contributors to the spreading of antimicrobial resistant bacteria. The present work aimed to measure the antimicrobial drug prescribing in dogs and cats in the Campania region, Italy by analyzing the Veterinary Electronic Prescriptions (VEPs) between 2019 and 2020. The medical records associated with antimicrobial drug prescription were collected considering the drug delivery (systemic or local) and the rationale for the treatment chosen. In the period under investigation, 166879 drugs were prescribed of which 129116 (73.37 %) were antimicrobial. A total of 83965 (65.03 %) antibiotics were prescribed to dogs, 40477 (31.35 %) to cats, and 4674 (3.62 %) to other companion animals. In dogs the 90.48 % of VEPs prescribed for systemic treatment included an antimicrobial Critically Important or Highly Important or Important for human medicine (WHO, 2018). The most widely commonly prescribed class were fluoroquinolones. The main prescribed antimicrobials were the metronidazole-spiramycin (29.71%), amoxicillin-clavulanic (19.58%), enrofloxacin and cephalexin in dogs (16.52 %) and enrofloxacin (22.64%) and amoxicillin-clavulanic acid (21.37 %) in cats. Based on the results the wide use of broad-spectrum or second-line antibiotics is emerged together with the use of the critically important antimicrobials for human medicine.

This study evaluated the effectiveness of an electronic system for managing drug-sensitive pulmonary tuberculosis patients in the Kyrgyz Republic. This was a cohort study using programmatic data. The study included patients registered on the paper-based system in 2019 and the electronic system between June 2021 and May 2022. Data was taken from 302 individuals from the electronic system for completeness and concordance in comparison with the paper-based system. The study showed that for most variables the completeness and concordance was 85.3%-93.0% and was lowest for non-mandatory fields such as medication side effects (26.8% vs 13.6%). No significant difference was observed in time taken from symptom onset to diagnosis and treatment initiation between the two systems. However, the electronic system had a significantly higher percentage of patients who initiated treatment on the same day of diagnosis (80.3% vs. 57.1%). The proportion with successful outcomes was similar in both groups, but the electronic system had a significantly lower proportion of patients with outcomes that were not evaluated or recorded (4.8% vs. 14.3%, p &lt; 0.001). The study highlights the potential advantages of implementing an electronic TB register system for improving records. We advocate for similar studies in other regions in Kyrgyz Republic.

In this article, we delve into the intricate behavior of electronic mechanisms underlying NMR magnetic shieldings, σ, in molecules containing heavy atoms such as cadmium, platinum, and mercury. Specifically, we explore PtXn^{−2} (X = F, Cl, Br, I; n = 4, 6) and XCl2 Te2 Y2 H6 (X = Cd, Hg; Y = N, P) molecular systems. It is known that the leading electronic mechanisms responsible for the relativistic effects on σ are well characterized by the linear response with elimination of small components model (LRESC). In this study, we present results obtained from the innovative LRESC-Loc model, which offers the same outcomes as the LRESC model but employs localized molecular orbitals (LMOs) instead of canonical MOs. These LMOs provide a chemist’s representation of atomic core, lone pairs, and bonds. The whole set of electronic mechanisms responsible of the relativistic effects can be expressed in terms of both non-ligand-dependent and ligand-dependent contributions. We elucidate the electronic origins of trends and behaviors exhibited by these di- verse mechanisms in the aforementioned molecular systems. In PtX4^{−2} molecules, the predominant relativistic mechanism is the well-established one-body spin-orbit (σ^SO(1) ) mechanism, while the paramagnetic mass-velocity (σ^Mv ) and Darwin (σ^Dw ) contributing mechanisms also demand con- sideration. However, in PtX6−2 molecules, the σ Mv+ Dw contribution surpasses that of the SO(1) mechanism, thus influencing the overall ligand-dependent contributions. As for complexes con- taining Cd and Hg, the ligand-dependent contributions exhibit similar magnitudes when nitrogen is substituted with phosphorus. The only discrepancy arises from the σ^SO(1) contribution, which changes sign between the two molecules due to the contribution of bond orbitals between the metal and tellurium atoms.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

(1) Objectives. Patients with heart failure (HF) who experience hospitalizations for worsening HF (HFH) are at high risk of subsequent events. We aimed to evaluate the impact of an outpatient care management program that includes a clinician-to-clinician e-consultation using an integrated electronic medical record in a healthcare area with a widely dispersed population on delay time in care, hospital admissions, and mortality in a high-risk group of patients with HF and previous episodes of HFH. (2) Methods. We selected 6,444 HF patients who visited the cardiology service at least once between 2010 and 2021. Of these, 4,851 were attended in e-consult, and 2,008 in one-time in-person consultations. In 2,230 HF patients, there was documentation of a previous episode of HFH. Using an interrupted time series regression model, we analysed the impact of incorporating e-consult into the health care model in the group of patients with HFH and evaluated the elapsed time to cardiology care, heart failure (HF), cardiovascular (CV), and all-cause hospital admissions and mortality, calculating the incidence relative risk (iRR). (3) Results. In the group of patients with previous HF hospitalizations, the introduction of e-consult substantially decreased waiting times to cardiology care. The time elapsed to care after e-consult implementation was significantly reduced compared with the previous in-person period (8.6 [8.7] vs 55.4 [79.9] days, p&lt;0.001). In that group of patients, after e-consult implantation, hospital admissions for HF were reduced (iRR [CI95%]: 0,837 [0,840-0,833]), 0,900 [0,862-0,949] for CV and 0,699 [0,678-0,726] for all-cause hospitalizations. There was also lower mortality (iRR [CI95%]: 0.715 [0.657-0.798] due to HF, 0,737 [0.764-0.706] for CV and 0,687 [0.652-0,718] for all-cause). The improved outcomes after e-consultation implementation were significantly higher in the group of patients with previous HFH and were independent of the patient’s clinical characteristics managed during the in-person or e-consultation periods. (4) Conclusions. In HF patients with previous HFH, an outpatient care program that includes an e-consult significantly reduced waiting times to cardiology care and was safe, with a lower rate of hospital admissions and mortality in the first year.

Peripapillary intrachoroidal cavitation (PICC) is a yellow-orange lesion, located at the outer border of the myopic conus. First described as a localized detachment of the retinal pigment epithelium, its intrachoroidal location was later disclosed, justifying its current name. PICC is related to other myopic complications like posterior staphyloma, but its pathogenesis is not clear to date. Although it has been considered a benign condition, most eyes with PICC show visual field defects, leading to diagnostic uncertainty as these deficits resemble those observed in glaucoma. Furthermore, eyes with PICC can develop macular detachment with retinoschisis. Finally, misdiagnosis of PICC as a metastatic choroidal tumor may lead to unnecessary and anxiety-provoking investigation. Advances in optical coherence tomography (OCT) imaging have improved the visualization of ocular structures, contributing to the understanding of PICC. Recently high optic nerve sheaths traction forces during eye movements in highly myopic eyes have been suggested as promoters of PICC, renewing interest around this condition. However, a review of PICC is still lacking. Therefore, we aimed to provide a concise yet comprehensive overview of the current state of the art, focusing on OCT documentation, pathophysiology and potential future perspectives based on biomechanics of the optic nerve.

Background. In the last decade, it was concluded that glaucomatous optic neuropathy is part of the neurodegenerative diseases in which destructive neuronal lesions are located not only in the structure of the retina, but they are also present at the level of the central visual and nervous pathways. Patients with Primitive Open Angle Glaucoma may have experienced changes such as sensorineural hearing loss as well as balance changes. The purpose of this study is to evaluate the degree of involvement of the auditory system in patients with glaucoma, the structural changes in the optic nerve and, to establish correlation between the hearing loss and structural changes in the optic nerve. The subjects included in the study are grouped as follows: a group of patients with glaucoma that will be compared to a group of patients without glaucoma only as well as identi-fy-ing the evolution of structural changes in optic nerve to patients with glaucoma and to normal patients. Material and methods. It is a prospective, cross-sectional study on 32 eyes of 16 subjects with Primitive Open Angle Glaucoma in a study group and 24 eyes of 12 healthy subjects in con-trol group with a mean age of 62 years in both groups. Both groups underwent ophthalmo-logical, audiological and radio imaging evaluation: Pure-tone audiometry (PTA) were recorded, oph-thalmologic evaluations according to a standardized protocol and MRI cerebral examination was performed. Results: In the Study group patients, compared to the Control group, the average lev-els of the left PTA, the cup/disc (C/D) area in both eyes, the C/D ratio in both eyes are in-creased. The mean level of Retinal nerve fiber layer (RNFL) mean thickness was slightly lower in patients with glaucoma. Multivariate analysis demonstrates that gender can be a good predictor of C/D area, gender and age can be good predictors of PTA both eyes and C/D ratio in the right eye, and gender, age and background can be good predictors of disc area in the left eye. Conclu-sions: Pa-tients with Primitive Open Angle Glaucoma show changes in audiometry test in correla-tion with ophthalmological parameters demonstrating that the auditory system can be affected in Primitive Open Angle Glaucoma. This study emphasizes the problem of interdisciplinarity in medicine with the aim of ensuring the quality of life of patients with glaucoma. A good collabora-tion between ophthalmologist and otolaryngologist will be very useful for these patients.

Optical fiber sensors based on tapered optical fiber (TOF) structure have attracted a considerable amount of attention from researchers due to the advantages of simple fabrication, high stability, diverse structures, and have great potential for applications in many fields such as physics, chemistry and biology. Compared with ordinary optical fibers, TOF with their unique structural characteristics significantly improve the sensitivity and response speed of fiber-optic sensors and broaden the application range. This review presents an overview of the latest research status and characteristics of fiber-optic sensors and TOF sensors. Then the working principle of TOF sensors, fabrication schemes of TOF structures, novel TOF structures in recent years, and the growing emerging application areas are described. Finally, the development trends and challenges of TOF sensors are prospected. The objective of this review is to convey novel perspectives and strategies for the performance optimization and design of TOF sensors based on fiber-optic sensing technologies.

Physics of high-Tc superconducting cuprates is obscured by the effect of strong electronic correlations. One way to overcome the problem is to seek for an exact solution at least within the small cluster and expand it to the whole crystal. Such an approach is in the heart of the cluster perturbation theory (CPT). Here we develop CPT for the dynamic charge and spin susceptibilities (spin-CPT), within which the correlation effects are explicitly taken into account by the exact diagonalization. We apply spin-CPT to the effective two-band Hubbard model for the cuprates obtained from the three-band Emery model and calculate one- and two-particle correlation functions, namely, spectral function and spin and charge susceptibilities. Doping dependence of the spin susceptibility was studied within spin-CPT and CPT-RPA that is the CPT generalization of the random phase approximation (RPA). Both methods produce the low energy response at four incommensurate wave vectors in qualitative agreement to the results of the inelastic neutron scattering on overdoped cuprates.

In contemporary science and technology, photonic sensors are essential. They may be made to be extremely resistant to some physical parameters while also being extremely sensitive to other physical variables. Most photonic sensors may be incorporated on chips and operate with CMOS technology, making them suitable for use as extremely sensitive, compact, and affordable sensors. Photonic sensors can detect electromagnetic (EM) wave changes and convert them into an electric signal due to the photoelectric effect. Depending on the requirements, scientists have found ways to develop photonic sensors based on several interesting platforms. In this work, we extensively reviewed the most generally utilized photonic sensors for detecting vital environmental parameters and personal healthcare. These sensing systems include optical waveguides, optical fibers, plasmonics, metasurfaces, and photonic crystals. Various aspects of light are used to investigate photonic sensors' transmission or reflection spectra. In general, resonant cavity or grating-based sensor configurations that work on wavelength interrogation methods are preferred, so these sensor types are mostly presented. We believe this paper will provide insight into the novel types of available photonic sensors.

Semantic interoperability facilitates exchange and access of health data that is being documented in EHRs with various semantic features. In the EU, the regulation proposal of European health data space requires development of semantic interoperability. To achieve a fully integrated EHDS ecosystem leveraging the value of health data, stakeholders need to overcome challenges of implementing common standards and other semantic interoperability features. We aimed to research what scientific evidence is available on developing semantic interoperability. Our research questions focused specifically on key features and approaches for semantic interoperability and on possible benefits of these choices. For that purpose, we performed a systematic literature review by defining our study framework based on previous research. Our results consisted of 10 studies where data models, ontologies, terminologies, classifications, and standards were applied for building interoperability. Through increased access to interoperable patient information, a better quality and outcomes in care can be achieved. Better communication based on easily accessible data is facilitated between health professionals and between clinicians and the patients. When heading towards semantic harmonization as outlined in the EHDS proposal, more experiences and analyses are needed to assess how applicable the chosen solutions are for semantic interoperability of European health care data.

In this paper, a range-gated lidar system utilizing an LN crystal as the electro-optical switch and a SCMOS (Scientific Complementary Metal Oxide Semiconductor) imaging device is designed. To achieve range-gated, we utilize two polarizers and a LN (LiNbO3) crystal to form an electro-optical switch. The optical switch is realized by applying a pulse voltage at both ends of the crystal due to the crystal's conoscopic interference effect and electro-optical effect. The advantage of this system is that low-bandwidth detectors such as CMOS and CCD (Charge-coupled Device) can be used to replace conventional high-bandwidth detectors such as ICCD (Intensified Charge Coupled Device), and time it has better imaging performance under specific conditions at the same. However, after using an electro-optical crystal as an optical switch, a new inhomogeneity error will be introduced due to the conscopic interference effect of the electro-optical crystal, resulting in range error of the lidar system. To reduce the influence of inhomogeneity error on the system, this paper analyzes the sources of inhomogeneity error caused by the electro-optical crystal and gives the crystal inhomo-geneity mathematical expression. A compensation method is proposed based on the above inho-mogeneity mathematical expression. An experimental lidar system is constructed in this paper to verify the validity of the compensation method. The experimental results of the range-gated lidar system show that in a specific field of view (2.6mrad), the lidar system has a good imaging per-formance, its ranging standard deviation is 3.86cm and further decreased to 2.86cm after com-pensation, which verifies the accuracy of the compensation method.

Increased screen time during the COVID-19 pandemic and the accelerated incorporation of technology into daily practices have directly contributed to the increased prevalence of eye disease. The human eye is not built for continual technological use and must adjust to exposure to digital screens. Overexposure to technology can result in eye strain and an increased risk of eye diseases such as myopia with complications later in life, including retinal tears, cataracts, and macular degeneration. As vision and ocular diseases become more prevalent, the study of eye diseases, including their causes and treatments, is especially relevant. There is a need to prevent ocular diseases before they become a burden to individuals, their families, and their communities by better understanding the pathophysiology of ocular diseases. Several ocular diseases are thought to be caused by imbalances in reactive oxygen species (ROS) and autophagy. ROS refers to a class of highly reactive oxygen-containing molecules that can undergo damaging reactions with other molecules in the cell. Autophagy is a cellular process of self-eating whereby damaged, harmful, or dead material in cells is broken down to maintain cellular homeostasis. This paper discusses the role of ROS and autophagy in the pathogenesis of computer vision syndrome (CVS), digital eye strain (DES), myopia, cataracts, glaucoma, diabetic retinopathy (DR), age-related macular degeneration (AMD), optic nerve crush injury (OCN), optic nerve gliomas, and retinoblastoma. Lifestyle changes such as limiting screen time, ensuring adequate exposure to evening sunlight, and using blue light protection measures or protective eyewear are important in the prevention of eye disease. Nutrition also contributes significantly to eye health. A balanced diet rich in vitamins and antioxidants may help to prevent ROS and autophagy imbalance-induced eye disease. Medical and surgical treatments become necessary when preventative measures fail. This paper also addresses how government measures to decrease the onset of eye disease, including targeted programs to increase access to fresh vegetables and fruits in food deserts, are a critical macro-level avenue to reduce eye disease prevalence in the US, which according to the National Eye Institute, costs $139 billion yearly.

Innovation development in healthcare has paved the path towards the improvement in system efficiency, patient care and cost-effective healthcare services, increasing the overall efficiency of the healthcare system in a significant manner. Electronic medical record system has fostered interoperability and collaboration in healthcare departments by enabling different systems to exchange and use patient data. This trend has been accelerated dominantly by the pandemic, leading to increased use of telemedicine, referring specifically to the use of electronic communication to provide healthcare services remotely. Moreover, an increased prevalence towards the use of artificial intelligence and machine learning in healthcare has contributed effectively towards the rigorous and informed analysis of large amounts of data as well as to identify patterns or trends that may be useful for improving care delivery or identifying potential issues. A unified electronic medical record System that will generate competitive opportunities and success prospects with reference to enhanced interoperability in US healthcare departments, can contribute towards the improvement in the quality and efficiency of care by making it easier for healthcare providers to access and share patient information as well as reducing the risk of errors in effective patient care.

The extracellular matrix (ECM) is earning an increasingly relevant role in many disease states and the process of aging. Analyzing these disease states is possible with GWAS and PheWAS methodology, and through our analysis, we aimed to explore the relationships between polymorphisms in the compendium of ECM genes (i.e., matrisome genes) in various disease states. A significant contribution on the part of the ECM polymorphisms is evident in many varying types of diseases, particularly those in the core matrisome genes. Our results confirm previous links to connective tissue disorders, but also unearth new and underexplored relationships with neurological, psychiatric, and age-related disease states. Upon analysis of drug indications for gene-disease relationships, we identified numerous targets that may be repurposed for age-related pathology. The identification of ECM polymorphisms and their contribution to disease plays an integral role in future therapeutic developments, drug repurposing, precision medicine, and personalized care.

The aim of study was to investigate epidemiology aspects of magnetic resonance imaging (MRI) during COVID-19 pandemic. The study comprised depersonalized residents of Tomsk and Tomsk Region (n = 1714). Invitations to take online survey were sent to 50,000 residents by target SMS with response rate of 1.2% (n = 727, Cohort 1). Cohort 2 comprised retrospective patients (n = 987) who underwent contrast-enhanced cardiac MRI (CMR) in 2019-2022. Referrals, clinical characteristics, diagnosis, gender, age, past COVID-19, MRI study protocols, and MRI data were analyzed. 29% of respondents in cohort 1 received MRI examination within past two years; 26% of respondents considered MRI the most informative imaging modality for detecting COVID-19 pneumonia; 12% of respondents reported MRI unavailable. Proportion of CMR among MRI studies increased during COVID-19 pandemic, and maximum incidence of cardiac diseases detected by MRI was in 2021. Incidence of myocardial fibrosis increased from ~67% in 2019 to ~84% in 2022. The rate of outpatient MRI studies significantly increased in 2020, but returned to pre-pandemic level in 2021. COVID-19 pandemic increased the need for MRI and CMR. Patients with history of COVID-19 had persistent and newly occurring symptoms of myocardial damage suggesting chronic cardiac involvement requiring continuous follow-up.

COVID-19 pandemic-related pressures on primary care may have driven inappropriate continuation of antibiotic prescriptions. Yet prescribing modality (repeat/non-repeat) has not previously been investigated in a pandemic context. Using the OpenSAFELY-TPP analytics platform, we analysed repeat/non-repeat prescribing frequency in monthly patient cohorts between Jan 2020–2022. In-depth analysis was conducted on Jan 2020 (“pre-pandemic”) and Jan 2021 (“pandemic”) cohorts. Per-patient prescribing and clinical conditions were determined by searching primary care record data using clinical code lists. Repeat prescribing was defined as >=3 prescriptions in a 6 month lookback period. Associations between demographics (e.g. age, sex, geography) and repeat/non-repeat prescribing were explored using unadjusted risk ratios. Antibiotic prescribing declined from May 2020; non-repeat prescribing declined more strongly than repeat prescribing (maximum declines -26% vs -11%, respectively). In the pandemic cohort, older patients were at higher risk of prescribing (especially repeat prescribing). The most common clinical conditions for repeat prescribing were COPD comorbidity and urinary tract infection. Comorbidities were more common among repeat vs non-repeat prescribed patients. In the pandemic cohort, vs pre-pandemic, repeat and non-repeat prescribing for comorbidities generally declined less compared with shorter-term conditions (infections, including COPD exacerbation/lower respiratory tract infection). Our findings inform ongoing development of stewardship interventions in England..

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.