Road traffic transportation has flourished in the process of urbanization by its advantages, but it also produces harmful environmental vibrations. The vibration problem is especially significant for production workshops with precision instruments. A field measurement was conducted to analyze the source characteristics and propagation laws of traffic-induced vibrations. Off the northern side of an urban highway lies a microelectronics workshop. When a large truck passes by, both the vibration responses on the ground and in the workshop considerably increase. Greater vibration is produced in the vertical direction than in the X and Y axes. The predominant frequency band of the vibration response caused by road traffic vehicles is lower than 20 Hz. The vertical vibration responses of the first and second floors in the workshop greatly exceed the VC-C limit because of the high daily traffic flow. Attribute to the excitation of the operation of the manufacturing equipment on the second floor, the vertical vibration level of the second floor is essentially higher than that of the first floor. Therefore, it is impossible to disregard the micro-vibration in the workplace produced by the manufacturing machinery as well as the ex-citement of the road traffic. The measured data can be used to test potential numerical models for forecasting vibrations caused by traffic on roads as well as to guide vibration assessment work throughout the planning and design stages of roads.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

This paper presents a novel dynamic camera parameter control method for position and posture estimation of highly miniaturized AR markers (micro AR markers) using a low cost general camera. The proposed method performs iterative calculation of the marker’s position and posture to converge them to specified accuracy with dynamically updating the camera’s zoom, focus and other parameter values based on the detected marker’s depth distances. For a 10 mm square micro AR marker, the proposed system demonstrated recognition accuracy of better than ±1.0% for depth distance and 2.5∘ for posture angle with a maximum recognition range of 1.0 m. In addition, the iterative calculation time was at most 0.7 seconds in an initial detection of the marker. These experimental results suggest that the proposed method and system can be applied to a robotic precise handling of small objects with low cost.

The genus Eucalyptus is a globally captivated source of hardwood and is well known for its medicinal uses. The hybrid and wild species of Eucalyptus are widely used as exotic plantations due to their renowned potential of adapting to various systems and sites, furthermore, making the species the most extensively propagated. Despite unquestionable progression in biotechnological and tissue culture approaches, the productivity of plantations is still limited often due to the low efficiency of clonal propagation from cuttings. The obtained F1 hybrids yield high biomass and High-quality low-cost raw material for large-scale production, however, the development of hybrid, clonal multiplication, proliferation, and post-developmental studies are still major concerns. This riveting review describes the problems concerned with in-vitro and clonal propagation of Eucalypt plantation; recent advances in biotechnological and tissue culture practices for massive and rapid micro-propagation of Eucalyptus; as well, highlights the Eucalypt germplasm preservation techniques.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

The purpose of this review is to present the current role of ultrasound-based techniques in the diagnostic pathway of prostate cancer (PCa). With overdiagnosis and overtreatment of a clinically insignificant PCa over the past years, multiparametric magnetic resonance imaging (mpMRI) became recommended for every patient suspected of PCa before performing a biopsy. It enabled targeted sampling of the suspicious prostate regions, improving the accuracy of the traditional systematic biopsy. However, mpMRI is associated with high costs, relatively low availability, long and separate procedure or exposure to the contrast agent. The novel ultrasound modalities such as shear wave elastography (SWE), contrast-enhanced ultrasound (CEUS) or high frequency micro-ultrasound (MicroUS) may be capable of maintaining the performance of mpMRI without its limitations. Moreover, the real-time lesion visualization during biopsy would significantly simplify the diagnostic process. Another value of these new techniques is the ability to enhance the performance of mpMRI by creating the image fusion of multiple modalities. Such models might be further analyzed by artificial intelligence to mark the regions of interest for investigators and help to decide about the biopsy indications. The dynamic development and promising results of new ultrasound-based techniques should encourage researchers to thoroughly study their utilization in prostate imaging.

Parts of shotgun cartridges are a significant source of plastic litter in the marine environment. Empty cartridge shells may not be picked up by the hunter who fired them, and plastic wads that serve to separate the propellant from the shot load, are lost down-range when a shot is fired. Such litter items constitute a cosmetic and aesthetic problem on coastlines and may cause harm to marine animals and in the later stages of decomposition break down into harmful micro plastic particles. There exists no reliable estimate of the global exposure of marine ecosystems to this plastic source. However, in some countries it has been subject to closer examination, including for example, Denmark where the annual contribution of plastic wads into marine systems was estimated to 600,000 pieces (c2 tonnes), and the accumulated density of washed-up items (both wads and shells) was 3.7 items per 100 m coastline. Increasing awareness of this problem has caused scientists, hunters’ communities and governments to suggest altered practice including transition to the use of biodegradable cartridge components, first and foremost wads as this item is invariable lost during hunting. Several manufacturers provide shotgun cartridges containing biodegradable wads based on different types of materials, including fibers and various types of plastics, for example PVAL (poly(vinyl alcohol)) and PHA (polyhydroxyalkanoate). In this paper, we review the most recent literature on the amounts and related environmental hazards of plastic dispersed from hunting ammunition into marine ecosystems. We summarize the market availability of shotgun cartridges with biodegradable wads and discuss chemical, technical, economical and legal aspects of a transition to the use of such products.

ST-elevation myocardial infarction (STEMI) remains one of the leading causes of morbidity and mortality worldwide. The identification of novel metabolic and imaging biomarkers could unveil key pathophysiological mechanisms at the molecular level and promote personalized care in patients with acute coronary syndromes. We studied 38 patients with STEMI who underwent primary percutaneous coronary intervention and thrombus aspiration. We sought to correlate serum ceramide levels with micro-CT quantified aspirated thrombus volume and relevant angiographic outcomes, including modified TIMI thrombus grade and pre- or post-procedural TIMI flow. Higher ceramide C16:0 levels were significantly, but weakly correlated with larger aspirated thrombus volume (Spearman r=0.326, p=0.046), larger intracoronary thrombus burden (Nagelkerke R2=0.236, p=0.030) and worse pre- and post-procedural TIMI flow (Nagelkerke R2=0.210; p=0.049 and Nagelkerke R2=0.277; p=0.039, respectively). Ceramides C24:0 and C24:1 were also significantly associated with larger intracoronary thrombus burden (Nagelkerke R2=0.311; p=0.008 and Nagelkerke R2=0.423; p=0.001, respectively). In conclusion, serum ceramide levels (mainly C16:0 and C24:1) were higher among patients with larger intracoronary and aspirated thrombus burden. This suggests that quantification of serum ceramides might improve risk-stratification of patients with STEMI and facilitate a more individualized approach in everyday clinical practice.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

That form and function relates, is the maxim to anatomy and physiology. Yet form-function relations can be difficult to establish. Human subjects with excessive trabeculated myocardium in the left ventricle, for example, are diagnosed with non-compaction cardiomyopathy, but the extent of trabeculations may be without relation to ejection fraction. Rather than rejecting a relation between form and function, we may ask whether the salient function is assessed; is there a relation to electrical propagation, mean arterial blood pressure, propensity to form blood clots, or all? And how should extent of trabeculated muscle be assessed? While reviewing literature on trabeculated muscle, we applied Tinbergen’s four types of causation - how does it work, why does it work, how is it made, and why did it evolve - to better parse what is meant by form and function. The paper is structured around cases that highlight advantages and pitfalls of applying Tinbergen’s questions. It further uses the evolution of lunglessness in amphibians to argue lung reduction can impact on chamber septation, and it considers the evolution of an arterial outflow in fishes to argue that reductions in energy consumption may drive structural changes with little consequences to function. Concerning trabeculations, we argue they relate to pump function in the embryo in the couple of weeks before the onset of coronary circulation. In fetal and postnatal stages, a spectrum of trabeculated-to-compact myocardium makes no difference to cardiac function and in this period form and function may appear unrelated.

Porous structures and micropatterning surfaces play a crucial role in the development of highly sensitive force sensors. However, achieving these two conductive architectures typically requires complex materials synthesis and expensive manufacturing processes. In this study, we introduce a novel conductive composite film featuring a porous/micropyramid hybrid conductive architecture, which is achieved through a straightforward process of materials mixing and one-step screen printing. By utilizing a deep eutectic solvent in the ink component, micropores are induced in the printed composite, while the mesh of the screen mask acts as a template, resulting in a micropyramid film surface. We have successfully realized highly sensitive flexible force sensors with multifunctional capabilities for perceiving normal force and shear force.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

Most fully developed galaxies have vivid spiral structure, but the formation and evolution of spiral structure is still a mystery that is not fully understood in astrophysics. We find that the currently used equations of galactic dynamics contain some unreasonable components. In this paper, the following three working assumptions are introduced to simplify the galactic structural equations. 1. In the research of large-scale structure, the retarded potential of the gravitational field should be taken into account. The propagating time of the gravitational field from center to border is longer than the revolution periods of the stars near the center of galaxy. Newton's gravitational potential is unreasonable for such case, and the weak field and low velocity approximation of Einstein's field equation should be adopted. 2. The stars in a fully developed galaxy should be zero-pressure and inviscid fluid, and the equation of motion is different from that of ordinary continuum mechanics. Stars move along geodesics. 3. The structure of the galaxy is only related to the total mass density distribution. The equation of state of dark halo is different from that of ordinary luminous interstellar matter, so their trajectories are also very different. Dark halo and ordinary matter in galaxy are automatically separated. The total mass density distribution can be presupposed according to the observation data, and then it can be determined by comparing the solution of the equations with the observed data. These assumptions and treatments are supported by theory and observation. The variables of the equations of simplified galactic dynamics are separated from each other, and the equations are well-posed and can be solved according to a definite procedure. Therefore, this simplified dynamic equation system provides a more reasonable and practical framework for the further study of galactic structure, and can solve many practical problems. Besides, it is closely related to the study of dark energy and dark matter.

In recent decades, perovskite-type compounds (ABB′O3) have been exhaustively studied due to their unique ferroelectric properties. In this work, a systematic study aiming to prepare fine particles in the binary system SrZrO₃–SrTiO₃ was conducted under hydrothermal conditions in a KOH (5 M) solution at 200 °C for 4 h under a constant stirring speed of 130 rpm. The precursors employed were SrSO₄ powder (< 38 μm size) and coprecipitated hydrous gels of Zr(OH)₄•9.64 H₂O (Zr-gel) and Ti(OH)₄•4.5H₂O (Ti-gel), which were mixed according to the stoichiometry of the SrZr_1-xTixO₃ in the compositional range of 0.0>x>100.0 mol% Ti⁴⁺. The XRD results revealed the formation of two crystalline phases rich in Zr⁴⁺, an orthorhombic structured SrZr0.93Ti0.07O3 and a cubic structured SrZr0.75Ti0.25O3 within the compositional range of 0.1–0.5 mol of Ti4+. A cubic perovskite-structured solid solution, SrTi1-xZrxO3, was preferentially formed within the compositional range of 0.5>x>0.1 mol% Ti⁴⁺. The SrZrO₃ and SrZr_0.93Ti_0.07O₃-rich phases had particle sizes averaging 3 m with a cubic morphology. However, a remarkable reduction in the particle size occurred on solid solutions prepared with hydrous Ti-gel over contents of 15 mol% Ti⁴⁺ in the reaction media, resulting in the formation of nanosized particles agglomerates with cuboidal shape self-assembled via a 3D hierarchical architecture, the sizes of these particles varied in the range between 141.0–175.5 nm. The limited coarsening of the particles is discussed based on the Zr-gel and Ti-gel dehydration capability differences that occurred under hydrothermal processing.

Alunogen, Al2(SO4)3·17H2O, occurs as an efflorescent in acid mine drainage, low-temperature fumarolic or pseudofumarolic (at coal fires) terrestrial environments. It is considered as one of the main Al-sulfates of Martian soils demanding comprehensive crystal chemical data of natural terrestrial samples. However, structural studies of natural alunogen were carried out in 1970s without localization of H atoms and have not previously been performed for samples from geothermal fields, despite the fact that these environments are considered as proxies of the Martian conditions. The studied alunogen sample comes from Verkhne-Koshelevsky geothermal field (Koshelev volcano, Kamchatka, Russia). Its chemical formula is somewhat dehydrated, Al2(SO4)3×15.8 H2O. The crystal structure was solved and refined to R1 = 0.068 based on 5112 unique observed reflections with I > 2σ(I). Alunogen crystalizes in P-1 space group, a = 7.4194(3), b = 26.9763(9), c = 6.0549(2) Å, α = 90.043(3), β = 97.703(3), γ = 91.673(3) °, V = 1200.41(7) Å3, Z = 2. The crystal structure consists of isolated SO4 tetrahedra, Al(H2O)6 octahedra and H2O molecules connected by hydrogen bonds. The structure refinement includes Al, S and O positions that are similar to previous structure determinations and thirty-four H positions localized for the natural sample first. The study also shows the absence of isomorphic substitutions in the composition of alunogen despite the iron-enriched environment of mineral crystallization. The variability of the alunogen crystal structure is reflected in the number of “zeolite” H2O molecules and their splitting. The structure complexity of alunogen and its modifications ranges from 333-346 bits/cell for models with non-localized H atoms to 783-828 bits/cell for models with localized H atoms. The higher values correspond to higher hydration state of alunogen.

Utilization of Bidirectional Reflectance Distribution Function (BRDF) model parameters obtained from the multi-angular remote sensing is one of the approaches for the retrieval of vegetation structural information. In this research, the potential of multi-angular vegetation indices, formulated by the combination of multi-spectral reflectance from different view angles, for the retrieval of forest above ground biomass was assessed. This research was implemented in the New England region with the availability of a high quality forest inventory database. The multi-angular vegetation indices were generated by the simulation of the Moderate Resolution Imaging Spectroradiometer (MODIS) BRDF/Albedo Model Parameters Product (MCD43A1 Version 6) based BRDF parameters. The effects of seasonal (spring, summer, autumn, and winter) composites of the multi-angular vegetation indices on above ground biomass, angular relationship of the spectral reflectance with above ground biomass, and the interrelationships between the multi-angular vegetation indices were analyzed. Among the existing multi-angular vegetation indices, only the Nadir BRDF-adjusted NDVI ( and Hot-spot incorporated NDVI ( showed significant relationship (more than 50%) with the above ground biomass. This research proposed two more sensitive vegetation structural indices, Fore-scattering Back-scattering NDVI and Vegetation Structure Index (VSI). The Fore-scattering Back-scattering NDVI showed higher sensitivity (R² = 0.62, RMSE = 52.46) towards the above ground biomass than existing multi-angular vegetation indices. Furthermore, the VSI performed in the most efficient way explaining 64% variation of the above ground biomass, suggesting that the right choice of the spectral channel and observation geometry should be considered for improving the estimates of the above ground biomass. In addition, the right choice of seasonal data (summer) was found to be important for estimating the forest biomass while other seasonal data were either insensitive or pointless. The promising results shown by the VSI suggest that it could be an appropriate candidate for monitoring vegetation structure from the multi-angular satellite remote sensing.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

The literature shows that both in laboratory and in industrial conditions, photocatalytic oxidation method copes quite well with the degradation of the most organic substances, including environmental toxins and molecular components of pathogenic microorganisms. However, the effective utilization of photocatalytic processes for environmental decontamination and disinfection require significant technological advancement both in the area of semiconductor material synthesis and its application. Here we focused on the presence and ‘photocatalytic capability‘ of photocatalysts among soil minerals, and their potential contribution to the environmental decontamination in vitro and in vivo. (The issue is sketched from the perspective of chemists and environmental scientist.) Reactions caused by sunlight on the soil surface are involved in its normal redox activity. It appears that some of them may take part in the soil decontamination. However, their importance for decontamination in vivo cannot be overstated due to diversity of soils on the Earth caused by the environmental conditions, such as climate, parent material, relief, vegetation etc. The solar-light induced reactions are just a part of extremely complicated processes dependent on a plethora of environmental determinates. Such multiplicity of affecting factors, which we tried to sketch from the perspective of chemists and environmental scientist, makes us rather sceptical about the effectiveness of the photocatalytic processes in vivo. On the other hand, there is a huge potential of the soils as the alternative source of useful photocatalytic materials of unique properties

The severe and complex COVID-19 symptoms, often needing hospital care, occur suddenly, late in the virus replication stage of SARS-CoV-2 infection. Hospitalised patients have tissue damage due to micro-clots at multiple sites. Could long-covid, also clinically variable, be a milder form caused by “nano-clots”, too small to cause detectable tissue damage? The timing and suddenness of the onset of serious disease needs an explanation. A paper reported on the first 20 children needing urgent hospital care. No child had any symptoms prior to suddenly becoming seriously ill, only one had a positive PCR test but all had positive SARS-CoV-2 antibody test. That finding indicated to me that this onset occurred at the moment of sero-conversion. An emerging viral moiety, the virion-IgG-antibody complex, has concentrations rapidly increasing, then decreasing. It is known that influenza-IgG-antibody-complex consists of many virions bound together by the antibody. It seems a reasonable step to propose that SARS-2, being a large virus and having many spike proteins, can form larger clumps of virus-IgG-antibody complexes than with influenza, the former being sufficiently large to initiate micro-clots. Therefore, my hypotheses is that the SARS-CoV-2 virion-antibody complex initiates micro-clot formation. Either before or after sero-conversion, the complex will be at too low a concentration to initiate micro-clots. To be useful, a hypothesis should be testable, provide explanations and give predictions. My presentation will give examples. I like the way that several apparently separate pieces of a jig-saw puzzle have come together to form a single picture. [I suggest that the reader scrolls down to the addenda [10,11 & 12] before reading the ICAR Poster]

The spatial segregation is a characteristic of Latin American cities, resulting in distinct dynamics of social inclusion and exclusion at both spatial and identity levels. Then, specific green spaces may convert into appreciated and contested territories, where various actors negotiate their uses and regulations. Considering a case-study in a green icon of the metropolitan city of Santiago de Chile, the main objective of the present study was to describe and comprehend the uses and meanings of the Quebrada Macul park among different social groups over the past two decades. We employed qualitative methods including six in-depth interviews with key informants (social and ecological leaders, historical neighbors, and park workers), five participant observations in the park, and statistical analysis of visitors. Results reveal that (1) the transition of being a popularly used hill to a metropolitan park rises tensions between public and private statuses of place; (2) conflicts emerge regarding who uses the space and how, reflecting power dynamics among different social groups; (3) the park, beyond being a public space, holds significant identity value for its historical residents, both for those who fought for its recovery and those who have lived closely, so processes of forgetfulness might be resentful. We conclude on enduring meanings of the park associated with the struggle for the place among different groups, highlighting the role of memory for the social integration of groups among natural spaces.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

The ceramic pastes of ca. 31 samples recovered from the Almaraz archaeological site, located in the south bench of Tagus River, were studied in detail using XRF, micro-Raman and GSDR spectroscopies, as well as the XRD technique. The ceramic sherds could be grouped into six categories, Red Slip tableware, Decorated tableware, Yellow Slip tableware, Grey tableware, Common tableware and Handmade pottery. Our studies of the mineralogic composition of the sherds` body indicate that all ceramics were produced locally, using silicious clays in most cases and calcareous clays in a few ones. Micro-Raman and ground state diffuse reflectance absorption spectroscopy provided useful information regarding the materials used to produce the coloured ceramics: hematite and brookite for the red slip and decorated ceramics, jacobsite or carbon black for the black decoration or grey ceramics. For the yellow slip tableware a simple engobe rich in yellow clay was used. XRF spectroscopic studies provided the elemental composition of all samples, and biplots of the Potassium (K) versus Calcium (Ca) contents, normalized to the silicon content of each ceramic paste, clearly show that Pliocene and Miocene local clays sources were used to produce most ceramics. Only one sherd can be considered a Lisbon production.

Micro-plastics (MPs) become significantly important to society since their commercial manufacture began in the 1950s because of their low production costs, stability, light weight, and adaptability. Plastic was produced in 400 million tons worldwide in 2020, compared to 1.5 million tons just 60 years earlier. Scientists predict that by 2050, plastic production would increase to 33 billion tons. MPs are a rising scientific and societal issue in the environment as a new type of contaminant that is widely disseminated in aquatic ecosystems and organisms. Aquatic species that come into contact with MPs for an extended period of time experience ecotoxicity, which includes oxidative stress, genotoxicity, neurotoxicity, and reproductive issues. In aquatic environments, MPs not only transport chemicals within animals but also serve as mediators for chemicals or other contaminants. As a result of co-exposure of MPs and chemical contaminants, various toxicity incidences involving aquatic organisms have been reported. The final exposure of MPs occurs in humans through biomagnification of aquatic edible products. This study presents an important overview of the literature on MP ingestion by aquatic biota. It covers topics such as the present scenario of plastic pollution worldwide, the pathways that MPs take to reach humans and aquatic species, the eco-toxicological impacts of MPs on aquatic species, the relation between MPs and other environmental pollution and the ensuing effects on aquatic organisms, and the MP pollution status in Bangladesh.

Castanea sativa Mill., an indigenous species of the mountainous Gabala region of Azerbaijan, where its local variety is now facing the danger of extinction. The preservation of this variety of European chestnut requires the development of effective strategies for reliable in vitro regeneration systems as an alternative to traditional methods, which has become the main objective of this study. In solving this problem, the generally accepted technique of micro-multiplication of axillary shoots was mainly used. First, a phased sterilization of was carried out using liquid soap, Previkur fungicide and mercury (II) chloride. DKW (Driver and Kuniyuki Walnut) nutrient medium was used for germination of explants, into which growth stimulants BAP (Benzilamunapurine), IBA (Indole - 3 butyric acid), IAA (Indole Acetic acid), NAA (Naphthalene Acetic Acid) and GA3 (Gibberelic acid) were introduced in various combinations and quantities. The test of the above-mentioned sterilization model revealed significant shortcomings in terms of the acceptability of the results obtained (16-77%). It was also found that the germination of explants takes 14 days and it is better to conduct it in a DKW environment containing hormones BAP (0.6 mg), IBA (0.1 mg) and GA3 (0.1 mg) / 1 L DKW. A mixture of BAP (0.1mg) + IBA (0.35 mg) is more suitable for the reproduction of grown explants + GA3 (0.2 mg) / 1 l DKW (the result is 3 new micro-plants for each explant), and for good root formation (it takes 30 days) – a mixture of IBA 1.0 mg + NAA 0.5 mg + IAA 0.5 mg / l L DKW. After the shoots have acquired a certain length (at least 1.5 cm), it is required to transfer them for 22 days to a DKW medium containing IBA (1 mg), IAA (0.5 mg) and NAA(0.5 mg) / l L DKW so that the root splitting process begins and ends.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

Objective: The purpose of this study was to evaluate the surface texture and biofilm adhesion of veneered or CAD/CAM milled zirconia (partially stabilized with yttrium) after professional oral hygiene procedures. Samples (4x4 mm, thickness 2 mm; n = 72) were separated from zirconia blanks (3Y-TZP-LA). One group was veenired with ceramics and the other group of samples was CAD/CAM milled. Each group had 2 subgroups: polished and glazed. The samples were subjected to simulated strokes of professional brushing using abrasive paste and ultrasonic scaling. Parameters of surface micromorphology and receptivity to biofilm were calculated before and after simulating the given methods of professional maintenance of oral hygiene. The characteristics of zirconia surface were evaluated by scanning electron microscopy (SEM). Microbial bacterial/fungal species (Staphylococcus aureus, Streptococcus sanguinis and Candida albicans) were used and cultured on the respective sterilized zirconia surfaces. The amount of biofilm formation on zirconia surface was quantified by colony forming unit (CFU) counts. Results: SEM analysis showed the greatest change in surface microtopography after the use of ultrasonic scaling, in glazed zirconia samples. Less formation of colonies on the surface CAD/CAM milled zirconia restorations was observed. Conclusion: Routine methods of professional maintenance of oral hygiene can damage the surface of glazed zirconia restorations.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

The device and method in accordance with the constant pressure regulation of micro droplet PCR in microfluidic chips are developed to explore the optimization way for the micro droplet movement, fragmentation, and bubble generation in microfluidic chips in existing digital PCR technology. In the developed device, an air source device is adopted to regulate the pressure in the chip, such that micro droplet generation and PCR amplification without bubbles can be achieved. In 3 min, the sample in 20ul will be distributed into nearly 50,000 water-in-oil droplets exhibiting a diameter of about 87μm, and the micro droplet will be subjected to a close arrangement in the chip without air bubbles. The device and chip are adopted to quantitatively detect the human gene . As indicated by the experimental results, a good linear relationship exists between detection signal and DNA concentration ranging from 101~ 105 copies /μL (R2=0.999). The micro droplet PCR devices based on constant pressure regulation chips exhibit a wide variety of advantages (e.g., achieving high pollution resistance, micro droplet fragmentation and integration avoidance, reducing human interference, and standardizing results). Thus, micro droplet PCR devices based on constant pressure regulation chips have promising applications in nucleic acid quantification.

Artificial intelligence, a key technological tool in the era of the 4th Industrial Revolution, is being actively applied to education beyond industry, economy, and culture. In the future society, understanding and using artificial intelligence technology will be considered an essential skill for everyone, and the professionalism of AI education for pre-service teachers nurturing future talents is also important. This study verifies the effectiveness of pre-service teachers after undergoing a 15-week extension program consisting of AI Literacy Education (10 weeks), AI-Linked Subjet Education (3 weeks), and Micro-teaching (2 weeks) which was designed to enhance the AI ​​education professionalism of pre-service teachers. The AI Literacy Education section consisted of understanding AI, AI ethics, and basic programming, and the education was conducted through both experience and practice. After that, the pre-service teachers analyzed the curriculum of the 5th and 6th grades of an elementary school, and developed a subject-related education program using AI tools in three stages. Using the developed program, micro-teaching classes were conducted twice. The study results are as follows. First, there was a change in the positive perception of AI (p<.05). Second, the understanding of AI educational technology tools was improved and the recognition of the usefulness of developing a curriculum-related program was expanded. Third, the importance of teacher competency development was learned through the micro-teaching, and the students' understanding of the learning process was expanded.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.

Calibration of flow devices is important in several areas of pharmaceutical, flow chemistry and microfluidic applications where dosage of process liquids or accurate measurement of the flow rate is important. The process-oriented liquid itself might influence the performance of the flow device and the simultaneous determination of the dynamic viscosity under flow conditions might be a valuable information for the process parameters. To offer the simultaneous calibration of the dynamic viscosity of the process-oriented liquid at the corresponding flowrate, METAS has built a pipe viscometer for the traceable in-line measurement of the dynamic viscosity in the current flow facilities for low flow rates from 1 L/min to 150 mL/min and pressure drops up to 10 bar. The traceability of all the measuring quantities as well as the geometrical dimensions of the micro tube guarantee the traceability of the pipe viscometer to SI units. The most challenging part is the traceable determination of the inner diameter of the micro tube. This can be achieved by measuring the pressure drop as a function of flow rate with the pipe viscometer and applying the law of Hagen-Poiseuille with a traceable dynamic viscosity of a reference liquid (water) or perform the measurements with the micro-CT at METAS, which determines the inner diameter by x-ray diffraction. The validation of the stated measurement uncertainty of the pipe viscometer has been performed by means of calibration of the dynamic viscosity of several reference liquids with traceable density and kinematic viscosity. The setup of the facility, the traceability as well as the uncertainty calculation of the pipe viscometer for the in-line measurement of the dynamic viscosity are discussed in this paper.

Micro-expression (ME) is one of the key psychological stress reactions. It is a modest, spontaneous facial mechanism. ME has significant applicability in a variety of psychologically-related sectors because to its precision and unpredictability with regard to psychological manifestations. Nevertheless, the current Micro-expression recognition (MER) algorithms have poor accuracy and a limited quantity of ME data, and this study issue has not been thoroughly investigated. Therefore, we present an approach for deep learning based on a Spatio-temporal capsule network (STCP-Net). STCP-Net has four components: a jitter reduction module, a differential feature extraction module, an STCP module, and a fully linked layer. The first two modules are aimed to extract diversifying differential features more precisely and to limit the influence of head jitter. The STCP module is used to extract Spatio-temporal features layer by layer, taking the temporal and geographical connection between features into account. This research runs sufficient trials using the Leave One Subject Out (LOSO) methodology for cross-validation using the CASMEII dataset. The conclusion and analysis demonstrate that the algorithm is innovative and efficient.

Cancer stem cells (CSCs) are one of the cell types that account for cancer heterogeneity. They arrest in the G0 phase and generate non-CSC progeny by self-renewing and pluripotency activity, resulting in tumor recurrence, metastasis, and chemoresistance. One CSC can stimulate tumor relapse and can re-grow a metastatic tumor. So, CSC is a promising target for eradicating tumors, and developing an anti-CSC method has become a top priority in cancer therapy. In recent years competing endogenous RNA (ceRNA) have emerged as an important class of post-transcriptional regulators that affect gene expression via competition for microRNA (miRNA) binding. Furthermore, aberrant ceRNA expression is associated with tumor progression. To overcome therapeutic resistance due to CSCs, we need to improve our existing understanding of the mechanisms by which ceRNAs are implicated in CSC-related relapse. Thus, this review was designed in order to discuss the role of ceRNAs in CSCs function. We reviewed the role of ceRNAs in acquiring CSCs characteristics in the form of different pathways including Rho GTPase/F-actin_ Yes-associated protein (YAP)/transcriptional co-activator with PDZ-binding motif (TAZ) (Hippo), Wnt/β-catenin pathway, transforming growth factor (TGF)-b–urothelial carcinoma-associated 1 (UCA1)–Slug pathway, etc. Finally, considering the comprehensive impacts of the ceRNA network on different pathways, a treatment strategy driving the ceRNA network might be effective. Targeting ceRNAs may open the path for new cancer therapeutic targets and can be used in clinical research.

This research was specifically aimed at assessing the influence of sulfur in triple-super phosphate (TSP) on wheat yield. From the results, wheat showed response to sulfur (S) from gypsum (in 67%); and nitrogen (N) from urea in about 100% (of 24 sites). Based on this N was found to be the most limiting element to wheat production followed by sulfur, and then by phosphorus. TSP is tested to contain agronomically up to 2-6% by weight of S. However, wheat didn’t show response to S impurity supplied in the form of TSP. Though, not statistically significant, it is observed that there have always been yield increments by certain percent due to S from TSP in 8 out of 10 target sites, which is depicted in the increasing trends of yield response curves. From this it is learnt that, the benefits of the accidental/incidental application of such high analysis fertilizers can be many-folds in the quality attributes of wheat, if the soils of such investigation at the same time would contain significant amount of organic matter (OM). Indeed, such analysis would be vital in varietal specific nutrient requirement studies in precision-farming and/or in categorizing soils into fertility gradients and fertilizer recommendation domains.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

We review recent work on broadband RF channelizers based on integrated optical frequency Kerr micro-combs combined with passive micro-ring resonator filters, with microcombs having channel spacings of 200GHz and 49GHz. This approach to realizing RF channelizers offers reduced complexity, size, and potential cost for a wide range of applications to microwave signal detection.

The optimization problem of two or more special-purpose functions of the energy system is subjected to an analysis. Based on experience of our research and general knowledge of partial solutions of energy system optimization at the level of control of production and power energy supply by energy companies in the Czech Republic, a special-purpose (cost) function has been defined. By analysing the special-purpose function, penalty and limitations have been defined. Using the fuzzy logic, a set of suitable solutions for the special-purpose function is accepted. An optimum of the special-purpose function is looked for using the simulated annealing method. The history of electricity consumption is sorted by day and by hour, representing the multidimensional data. When using the cluster analysis, type daytime diagrams of consumption are defined. Type daytime diagrams form prototypes of identified clusters. The so-called self-organizing neural network with Kohonen map attached is used to perform the cluster analysis. The result of our research is presented by an experiment.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Balínt Syndrome is an acquired disorder manifesting in the inability to recognize several objects at once (simultagnosia), inaccurate visually guided limb movements despite intact motor function (optic ataxia) and the inability to make accurate voluntary saccades to visual targets despite demonstrating unrestricted range of eye movements (ocular motor apraxia). Here we report the first case of a patient presenting with Balínt Syndrome caused by a platelet-derived growth factor receptor A mutation (PDGFRA)-induced Hypereosinophilic Syndrome (HES).

This paper proposes a novel micro-grid structure, which can operate fully-autonomously with inherent seamless switching. It can operate independently in both grid-connected and islanded mode as a self-governed entity without relying on the utility grid. An AC/DC/AC converter is employed as the interface between the micro-grid and the utility grid, which enables the two entities to have different voltages in grid-connected mode. Seamless switching between operation modes can be achieved naturally. The micro-grid is regulated to exchange predefined amount of power with the utility grid in grid-connected mode. This will benefit the power dispatching algorithm of the power system. The predefined power is estimated based on power forecasting of local renewable generations and loads with consideration of the Sate of Charge (SOC) of the battery, and is updated and broadcasted every certain period. A small scale AC micro-grid with a rotating generator, battery storage and solar arrays etc. is built for investigation. Matlab/Simulink results are provided to validate the robustness and flexibility of proposed micro-grid and its operation strategy.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

In recent years, Web APIs have become a de facto standard for exchanging machine-readable data on the Web. Despite this success though, they often fail in making resource descriptions interoperable due to the fact that they rely on proprietary vocabularies that lack formal semantics. The Linked Data principles similarly seek the massive publication of data on the Web, yet with the specific goal of ensuring semantic interoperability. Given their complementary goals, it is commonly admitted that cross-fertilization could stem from the automatic combination of Linked Data and Web APIs. Towards this goal, in this paper we leverage the micro-service architectural principles to define a SPARQL Micro-Service architecture, aimed at querying Web APIs using SPARQL. A SPARQL micro-service is a lightweight SPARQL endpoint that provides access to a small, resource-centric, virtual graph. In this context, we argue that full SPARQL Query expressiveness can be supported efficiently without jeopardizing servers availability. Furthermore, we demonstrate how this architecture can be used to dynamically assign dereferenceable URIs to Web API resources that do not have URIs beforehand, thus literally ``bringing'' Web APIs into the Web of Data. We believe that the emergence of an ecosystem of SPARQL micro-services published by independent providers would enable Linked Data-based applications to easily glean pieces of data from a wealth of distributed, scalable and reliable services. We describe a working prototype implementation and we finally illustrate the use of SPARQL micro-services in the context of two real-life use cases related to the biodiversity domain, developed in collaboration with the French National Museum of Natural History.

This study investigated the roles of transactions cost in MSMEs access to finance. This was done by investigating the impact of transactions cost on access to credit from both MSMEs and financial institutions (commercial banks and microfinance banks). From the MSMEs’ side, borrowing experience, decision lag, firm size and borrowers’ distance to the loan office were investigated. On the financial institution’s side, the costs of information gathering, loan administration, monitoring and loan enforcement were investigated. We used the questionnaire survey method, in-depth interviews and case studies, as well as the annual financial statements of the banks. We identified interest rate and collateral value as constraints to access to finance for MSMEs. We also found financial institutions’ attitude to MSMEs access to credit was not friendly. Financial institutions need to do more to bring down transaction cost of lending. This hopefully can be achieved by investing more in agent banking which would lower operating costs, as well as spreading risk, and ultimately increase credit intermediation to small businesses.

Hepatitis C virus (HCV) is a major medical health burden and leading cause of chronic liver disease and cancer worldwide. More than 58 million people are chronically infected with HCV, with 1.5 million new infections occurring each year. An effective HCV vaccine is a major public health and medical need as recognized by the World Health Organization. However, due to the high variability of the virus and its ability to escape the immune response, HCV rapidly accumulates mutations making a vaccine a formidable challenge. An effective vaccine must elicit broadly neutralizing antibodies (bnAbs) in a consistent fashion. After decades of studies from basic research through clinical development, the antigen of choice is considered to be the E1E2 envelope glycoprotein due to conserved, broadly neutralizing antigenic domains located in the constituent subunits of E1, E2, and the E1E2 heterodimeric complex itself. The challenge has been elicitation of robust humoral and cellular responses leading to broad virus neutralization due to the relatively low immunogenicity of this antigen. In view of this challenge, structure-based vaccine design approaches to stabilize key antigenic domains have been hampered due to the lack of E1E2 atomic-level resolution structures to guide them. Another challenge has been development of a delivery platform in which a multivalent form of the antigen can be presented in order to elicit a more robust anti-HCV immune response. Recent nanoparticle vaccines are gaining prominence in the field due to their ability to facilitate a controlled multivalent presentation and trafficking to lymph nodes, where they can interact with both the cellular and humoral components of the immune system. This review focuses on recent advances in understanding the E1E2 heterodimeric structure to facilitate a rational design approach and the potential for development of a multivalent nanoparticle-based HCV E1E2 vaccine. Both aspects are considered important in the development of an effective HCV vaccine that can effectively address viral diversity and escape.

Soil structure is a sensitive and dynamic soil physical property which responds rapidly to different tillage systems, and thus it requires constant monitoring and evaluation. The visual evaluation of soil structure (VESS) and subsoil visual evaluation of soil structure (SubVESS) methods were used to assess the soil structure quality of clayey soils subjected to different tillage systems. The tillage systems were no-tillage (NT), conventional tillage (CT) and virgin land (VG). The study was conducted at Tshivhilwi and Dzingane in Thohoyandou, Vhembe District, Limpopo Province, South Africa. The NT system was practised for 8 and 40+ years at Tshivhilwi and Dzingahe, respectively. The results showed no impact of tillage system on both VESS and SubVESS at Tshivhilwi. The soil structure quality at Tshivhilwi as determined by VESS and SubVESS were found to be poor. However, at Dzingahe, both the VESS and SubVESS responded to the impact of tillage. At Dzingahe VESS showed a fair (Sq = 2.25) soil structural quality in the NT system, poor (Sq = 3.57) in the CT system and moderately poor (Sq = 3.05) in the VG. Similarly, at the same location the SubVESS scores were moderately good in the NT system, moderately poor for CT system and fair in the VG. The differences in the response of the VESS and SubVESS at the two locations were attributed to the differences in the duration at which the NT systems were practised. The VESS and SubVESS results were supported by selected measured soil physicochemical properties such as bulk density and porosity. In conclusion, the findings of this study showed that the VESS and SubVESS were able to effectively differentiate the impact of tillage systems on soil structural quality in clayey soils where NT was practised for a long period (40+ years) while it could not where NT was practised for a few years (8 years).

Multipactor is a common discharge phenomenon occurred in space microwave systems. The surface microstructure has been verified to be effective to mitigate multipactor. In this work, we design a square coaxial low-pass filter (SCLPF) with dielectric sheets loaded to check the multipactor dependence on the structure parameters of the loaded dielectric sheets, and further model groove structures on the sensitive area surface to lower the risk of multipactor. Simulation results indicate that the SCLPF loaded with alumina and PTFE exhibits good operational characteristics, and the multipactor threshold is significantly improved after introducing the surface grooves. Then we investigate the effects of three typical groove parameters, groove depth, groove number, and aspect ratio, on the multipactor threshold of the SCLPF device. The results show that the multipactor threshold raise at first as the groove number and groove depth increase, and then the threshold reaches a saturation status. For a deeper analysis of multipactor, we discuss how the grooves shelter the secondary electrons, and further mitigate the electron avalanche. Furthermore, the mechanisms of threshold saturation under the effect of groove parameters are analyzed in detail, and a contour map for the multipactor threshold of PTFE-loaded SCLPFs is given, which makes significant sense for predicting the multipactor threshold of the devices with its sensitive surface being grooved. The regularity of modulating the multipactor threshold by the groove structures obtained in this study is of engineering significance for suppressing multipactor in microwave devices in practical applications.

With the rapid development of the Internet industry, the problem of information overload has arisen due to the abundance of information available online. Recommendation algorithms, as the core of recommendation systems, have been attracting much attention and are a hot topic of research for many experts and scholars. The classical recommendation algorithms are mainly divided into three major categories: collaborative filtering recommendation algorithms, content-based recommendation algorithms, and hybrid-based recommendation algorithms. Although these algorithms are widely used in various fields, with the proliferation of information, these traditional recommendation algorithms are no longer able to meet the needs of the times. To address this issue, recommendation systems have been developed to provide users with personalized and relevant information or products. Despite the wide use of recommendation algorithms, such as collaborative filtering, content-based filtering, and hybrid approaches, traditional recommendation algorithms have limitations and are no longer suitable for meeting the demands of the times. This paper proposes a new recommendation algorithm, SFRRG, that fuses structure and feature information in graph neural networks to improve the performance of the recommendation system in rating prediction. The effectiveness of the proposed algorithm is demonstrated through experiments on various data sets and compared with existing recommendation algorithms.

The determination of the three-dimensional structure is a key step for the identification of new targets as well as the rational design of bioactive compounds. Herein, we report the synthesis and the structural elucidation of novel tetrameric macrocycles. Measurements were taken in solid and solution states with the help of X-ray scattering and NMR spectroscopy. The investigations made will help to find diverse applications for this new, promising compound class.

Due to the vast conformational space proteins can adopt, accurate and efficient prediction of protein structure remains still a challenging task, coupled with the intricacies of interatomic interactions and the limitations of current computational models in effectively navigating this complex molecular landscape. Additionally, the lack of comprehensive experimental data for all protein structures further exacerbates the difficulty in reliable machine learning-based prediction of the three-dimensional conformations of the proteios building block of life. Geometrically, Cartesian coordinate system (CCS, X, Y and Z) and spherical coordinate system (SCS, ρ, θ and φ) are two interconvertible coordinate systems, and are like two sides of one coin. Since the beginning of Protein Data Bank (PDB) in 1971, CCS has been the default approach to specify atomic positions with X, Y and Z in PDB. In this manuscript, therefore, I present a novel method for the reversible spherical geometric conversion of protein backbone structure coordinate matrices to three independent vectors: ρ, θ and φ. This reversible conversion facilitates lossless extraction of essential structural features from protein backbone structural data, enabling the development of advanced novel algorithms for protein structure prediction in future. In short, this inter-atomic SCS approach offers a comprehensive yet efficient means of representing protein backbone geometry, leveraging spherical coordinates to capture spatial relationships in a compact and intuitive inter-atomic manner, and to provide a robust framework for reversible feature extraction for the ongoing efforts in advancing the field of protein structure prediction, the holy grail of computational structural biology.

This paper introduces an innovative approach to numerically model Structure-Soil-Structure Interaction (SSSI) by integrating the Boundary Element Method (BEM) and the Finite Element Method (FEM) in a coupled manner. To assess the accuracy of the proposed method, a comparative study is undertaken, comparing its outcomes with those generated by the conventional FEM technique. Alongside accuracy, the computational efficiency aspect is crucial for the analysis of large-scale SSSI problems. Hence, the computational performance of the coupled BEM-FEM method undergoes a thorough examination and is compared with that of the standalone FEM method. The results from these comparisons illustrate the superior capabilities of the proposed method in comparison to the FEM method. The novel approach provides more reliable results compared to traditional FEM methods, serving as a valuable tool for engineers and researchers involved in structural analysis and design.

This paper investigates the hydroelastic responses of offshore floating solar photovoltaic farms (OFPVs) to minimize structural motion. The OFPV usually occupies a large sea space in the order of hectares and due to its huge structural length-to-thickness ratio, the structural deformation under wave action has to be taken into consideration. The flexible deformation of the structure under hydrodynamic loading is termed the hydroelastic response. Due to the relatively long structural length with respect to the encountering wavelength, the diffraction and radiation of waves have to be taken into account to accurately represent the hydrodynamic loadings on the floating platform. The numerical model is first validated by comparing the eigenvalues and eigenvectors of the OFPV obtained from the proposed numerical scheme with their counterparts obtained from an established finite element software. This is followed by the investigation of the hydroelastic response of various OFPVs designed in varying layout configurations. The various layout configurations are obtained by altering the floating modular units’ dimensions as well as the spacing of the OFPVs when deployed adjacent to each other. The optimal configuration that gives the best performance in terms of the overall smallest response, known as compliance, is then suggested. The results suggest that a longish OFPV layout has a lower hydroelastic response and the motion could be further reduced by increasing the global flexural stiffness via layout arrangement.

In this research, a design method for the graded triply periodic minimal surface (TPMS) structures with lightweight, high-strength, and high sound absorption properties is proposed. The graded TPMS structures are controlled by linear, quadratic, and sine functions. Uniform TPMS and graded TPMS were manufactured by laser powder bed fusion (LPBF) with AlSi7Mg powder, and an acoustic impedance tube test, compression test, and digital image correlation (DIC) test were ap-plied to obtain the sound absorption and compression properties. The sound absorption coefficient of a uniform Gyroid increases as the number of layers and surface thickness increase, and it in-creases as element size decreases. The sound absorption peak shifts to low frequencies as the number of layers increases. The sound absorption property of Type-Ⅰ graded TPMS is superior to the Type-Ⅱ, and the G-LinearⅠ has the highest sound absorption properties among the three functions. It reveals that the graded TPMS has superior sound absorption performance at low and medium frequencies. The compression and DIC results of graded TPMS also show excellent mechanical properties and energy absorption characteristics.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

In the Standard Model of elementary particles, the rest mass, magnetic moment and electric charge of the electron are considered to be natural constants. In this article it is proposed that these properties can be calculated in a simple way from the corresponding Planck units using the well-known period doubling phenomenon in nonlinear dynamical systems. Periods corresponding to the values of the electron and positron properties belong to a subset of stable periods. The periodic structures of the rest energy and magnetic moment consist of three internal degrees of freedom, whereas the Coulomb energy of the electric charge consists of four. The number of period doublings for the elementary charge determines the value of the fine structure constant alpha.

Transient flows result in unbalanced forces and high pressure in pipelines. Under these conditions, the combined effects of flow-induced forces along with sudden pipe displacements can create cracks in the pipeline, especially at the junctions. This situation consequently results in water leakage and reduced operational efficiency of the pipeline. In this study, displacements and stresses in a buried pressurized water transmission pipe installed by pipe jacking method are investigated using numerical modeling and considering interactions between fluid, pipe, and soil. The analyses were performed consecutively under no-flow, steady flow, and transient flow conditions, in order to investigate the effects of flow conditions on displacements and stresses in the system. Analyses of the results show that displacements and stresses in the jointed concrete pipes are significant under transient flow conditions. Moreover, because of pressure transient effects, maximum tensile stresses exceed the tensile strength of concrete at the junctions, leading to cracks and consequent water leakage.

The use of e-scooters and e-bicycles has been on the rise with an increased medical and financial burden. Our purpose was to identify risk factors for increased medical charges and recommend appropriate steps. We studied a retrospective cohort presenting to a level 1 urban trauma center from January 2018 through July 2019 due to micro-mobility platforms. The primary outcome for comparison was total billing cost and a regression analysis was performed to identify variables associated with higher cost. A total of 4073 patients were identified. The majority of which were males (67%), aged 20-30 years (41%). Helmet use reported in only 39.8%. Radiologic studies were performed more often in the e-bicycle group. Total billing charges amounted to 28.3 million New Israeli Shekels ($7.9 million). Average total cost was higher for e-bicycle injuries and in non-helmet users. Other factors associated with higher cost were age, and time of day 12:00-18:00. We recommend that urban cities invest in infrastructure in advance to micro-mobility introduction, regulate the use of e-platforms, designate resources for education on personal protective equipment and prepare medical centers in advance.

Micro nano bubbles (MNBs) can generate ·OH in situ, which provides a new idea for the safe and efficient removal of pollutants in water supply systems. However, the difficulty in obtaining stable MNBs causes the low efficiency of ·OH generation, which makes the inability to guarantee the removal efficiency of pollutants. This paper reviews the application research of MNBs technology in water security from three aspects: the generation process of MNBs in water, the generation rule of ·OH during MNBs collapse, and the control mechanism of MNBs on pollutants and biofilms. We found that MNBs generation methods are divided into chemical and mechanical (about 10 kinds) categories, and the instability of bubble size restricts the application of MNBs technology. The generation of ·OH by MNBs is affected by pH, gas source, bubble size, temperature, external stimulation. And pH and external stimulus have more influence on ·OH generation in situ than other factors. Adjusting pH to alkaline or acidic conditions and selecting ozone or oxygen as the gas source can promote the ·OH generation. MNBs’ collapse also releases a large amount of energy, which the temperature and pressure can reach 3000K and 5Gpa respectively, making it efficient to remove ≈90 % of pollutants (i.e., trichloroethylene, benzene, and chlorobenzene). The biofilm can also be removed by physical, chemical, and thermal effect. MNBs technology also has great application potential in drinking water, which can be applied to improve water quality, optimize household water purifiers, and enhance the taste of bottled water. Under the premise of safety, let people of different ages taste, finding that compared with ordinary drinking water, 85.7 % of people think MNBs water is softer, 73.3 % of people think MNBs water is sweeter. This further proves that MNBs water has a great prospect in the drinking water application. This review provides innovative theoretical support for solving the problem of drinking water safety.

This research investigates the microstructure and mechanical behaviour of a polylactic acid (PLA)-iron (PLI) composite designed to enable magnetic actuation. Tensile specimens of PLI are produced through Fused Filament Fabrication, incorporating diverse printing angles ranging from 0° to 90°, thereby facilitating the creation of a variety of layups. The microstructure of these 3D-printed composites is analysed using X-ray micro-tomography. Furthermore, the tensile mechanical properties of all composites are evaluated, and the findings are deliberated in relation to the conditions of the printing angle. Additionally, the fractography of broken specimens is examined using Scanning Electron Microscopy. The findings indicate that the printing angle plays a significant role in influencing the tensile properties of the 3D-printed PLI composites, particularly in adjusting mechanical anisotropy. Moreover, an optimal layup of 45°/45° is attained, resulting in an enhanced ranking of the tensile performance. These findings related to 3D-printed PLI composites present a cost-efficient option for manufacturing bio-sourced light-adaptive composites through 3D printing, enabling the generation of intricate magnetic actuation performance.

A fern, Polypodium aureum, possesses a specialized spore-releasing mechanism like a catapult induced by quick expansion of vaporized bubbles. This study introduces lipid-coated perfluorocarbon droplets to enable repeatable vaporization-condensation cycles, inspired by the repeatable vaporization of Polypodium aureum. Lipid-perfluorocarbon droplets have been considered not to exhibit repeatable oscillations due to bubble collapse by low surface tension of lipid layers. However, a single lipid-dodecafluoropentane droplet with a diameter of 9.17 µm shows expansion-contraction oscillations over 4,000 cycles by changing lipid composition and applying low power of 1.7 MHz ultrasound to induce partial vaporization of droplets. The optimal combinations of shell composition, droplet fabrication, and acoustic conditions can minimize damage on shell structure and quick recovery of damaged shell layers. The highly-expanding oscillatory microbubbles provide a new direction for fuel-free micro or nanobots as well as biomedical applications of contrast agents and drug delivery.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

Traumatic brain injury (TBI) affects millions of people annually, however, our knowledge of the diffuse pathologies associated with TBI is limited. As diffuse pathologies, including axonal injury and neuroinflammatory changes, are difficult to visualize in the clinical population, animal models are used. In the current study we used the central fluid percussion injury (CFPI) model in a micro pig to study the potential scalability of these diffuse pathologies in a gyrencephalic brain of a species with inflammatory systems very similar to humans. We found that both axonal injury and microglia activation within the thalamus and corpus callosum are positively correlated to the weight-normalized pressure pulse, while subtle changes in blood gas and mean arterial blood pressure are not. We also found that the majority of tissue generated up to 10 years previously is viable for immunofluorescent labeling after long-term refrigeration storage. This study indicates that a micro pig CFPI model could allow for specific investigations of various degree of diffuse pathological burdens following TBI.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (&gt;4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

This review paper delves into using micro-credentials in higher education ecosystems as a digital enablers. Micro-credentials, which are digital credentials that attest to a learner’s mastery of a specific skill or knowledge area, are becoming more popular in higher education. The paper examines the successful implementation of micro-credential frameworks in higher education, using case studies to demonstrate the advantages of micro-credentials. The review emphasizes the agility and flexibility of microcredentials, which enable learners to acquire new skills quickly and respond to changes in the job market. In addition, the paper discusses the digital nature of micro-credentials and how they allow institutionsto provide targeted, skills-based training that isrelevant to employers. It also explores how micro-credentials are delivered through online platforms, making them convenient and easily accessible for learners. The review underscores the significance of digital infrastructure, connectivity, and public utility for promoting micro-credentials. The paper argues that micro-credentials function as a digital enabler for higher edu- cation ecosystems, allowing learners to acquire targeted training and enabling institutions to expand their offerings and reach more students. The paper concludes by highlighting the potential for micro-credentials to help bridge the skills gap and equip learners with the skills necessary to succeed in today’s digital economy.

Micro-level language policy and planning (LPP) primarily concerns local actors' decision-making on matters in relation to language(s) and its users. Despite a growing body of literature focusing on micro language planning in educational settings, there is a scarcity of research examining early childhood education settings such as micro-level LPP context for young English language learners. By adopting a case study approach, the present study examined the educators' enactment of agency in micro-planning the English language education policy (LEP) in one Chinese kindergarten and the associated factors shaping their agency. Our study revealed that the sustainable implementation of the kindergarten English LEP depended on the principal, native English-speaking teachers, and the Chinese assistant teachers' different degrees of agency. Also, the research findings indicated an array of contextual and individual factors nested in a hierarchical structure that facilitated, guided, and constrained the educators' agency in a role-and circumstance-dependent manner. This study contributes to the pertinent literature by casting nuanced light on the different educators' contributions to the micro-level LPP against a national policy that does not endorse early-year English language education.

The study purpose was to train and validate a deep-learning approach to detect micro-scale streetscape features related to pedestrian physical activity. This work innovates by combining computer vision techniques with Google Street View (GSV) images to overcome impediments to conducting audits (e.g., time, safety, and expert labor cost). The EfficientNETB5 architecture was used to build deep-learning models for eight micro-scale features guided by the Microscale Audit of Pedestrian Streetscapes-Mini tool: sidewalks, sidewalk buffers, curb cuts, zebra and line crosswalks, walk signals, bike symbols, and streetlights. We used a train--correct loop, whereby images were trained on a training dataset, evaluated using a separate validation dataset, and trained further until acceptable performance metrics were achieved. Further, we used trained models to audit participant (N=512) neighborhoods in the WalkIT Arizona trial. Correlations were explored between micro-scale features and GIS-measured- and participant reported-macro-scale walkability. Classifier precision, recall, and overall accuracy were all >84%. Total micro-scale was associated with overall macro-scale walkability (r=0.300,p<.001). Positive associations were found between model-detected and self-reported sidewalks (r=0.41,p<.001) and sidewalk buffers (r=0.26,p<.001). Computer vision model results suggest an alternative to trained human raters, allowing for audits of hundreds or thousands of neighborhoods for population surveillance or hypothesis testing.

A theoretical description of quantum jumps at the level of elementary particles is proposed, based on a micro-cosmological interpretation of their de Broglie phase. The third quantization formalism proposed in current literature for the description of baby universes in quantum cosmology is used here to describe the breakdown of unitarity in the transition from the pre-jump to the post-jump wave function. The corpuscular aspect manifested by the particle in the micro-interaction that originates the jump is represented by a pair of evanescent "micro-universes", respectively pre- and post-jump, connected by a wormhole. The latter represents the actual implementation of the interaction that leads to the projection on the outgoing state; this interaction is always local, even when the selected outgoing state is entangled. Therefore, the decoherence which leads to the emergence of classicality is originated by the same fundamental interactions of the Standard Model involved in the unitary evolution of the wave function. The objective nature of the reduction process admits implications on the possibility of using the formalism in the cosmological context, which are briefly discussed.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

During March and April 2020, the European Union (EU) was the center of the COVID-19 pandemic. Many National Governments imposed severe lockdown policies to mitigate the health crisis. The European Parliament commissioned a survey to analyse the citizens’ attitudes over a number of issues related to the COVID-19 pandemic. 21804 European citizens in 21 EU countries responded the survey between 23 April and 1 May 2020. The paper analyses empirically the individual satisfaction that European citizens have experienced over the measures taken by the respective National Governments to control the COVID-19 pandemic. The analysis is based on a micro-econometric model (ordered probit) that explains the citizens’ satisfaction by a number of attitudes and sociodemographic factors. Our results reveal that Spaniards are the least satisfied citizens in comparison with Danes, Irelanders, Greeks and Croats who are the most satisfied nationals. The years of education and the social class also play a determinant role. We also find that the most important determinant is the political support to the Government, and that those who are more worried by the economy and the protection of individual rights are usually more critic with the measures than those who are more worried by the health consequences.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

Mineral profile of beef interests human health, but also animal performance and meat quality. This study analyzes the relationships of 20 minerals in beef (ICP-OES) with 3 animal performance and 13 meat quality traits analyzed on 182 samples of Longissimus thoracis. Animals’ breed and sex showed limited effects. The major sources of variation (farm/date of slaughter, individual animal within group and side/sample within animal) differed greatly from trait to trait. Mineral contents were correlated to animal performance and meat quality being significant 52 out of the 320 correlations at the farm/date level, and 101 out of the 320 at the individual animal level. Five latent factors explained 69% of mineral co-variation. The most important, “Mineral quantity” factor correlated with age at slaughter and with the meat color traits. Two latent factors (“Na+Fe+Cu” and “Fe+Mn”) correlated with performance and meat color traits. Two other (“K-B-Pb” and “Zn”) correlated with meat chemical composition and the latter also with carcass weight and daily gain, and meat color traits. Meat cooking losses correlated with “K-B-Pb”. Latent factor analysis appears be a useful means of disentangling the very complex relationships that the minerals in meat have with animal performance and meat quality traits.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines to turbofan with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving propulsive performance. The BMT 120 KS micro turbojet engine is selected for performance evaluation of the conversion process using gas turbine performance software, GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis carried out, an improvement in the converted micro gas turbine engine performance in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, fan speed operation may be adjusted independently of the core, allowing increased thrust generation or better fuel consumption. Therefore, enabling a wider gamut of operating conditions and enhances the performance and scope of tactical UAV.

Prolonged high-intensity grinding can modify the crystal structure of solid substances and/or induce chemical reaction, which is referred to as mechanochemical reaction. Such reactions can exert positive influences on hydrometallurgical processes, therefore, many researchers have applied mechanochemical reactions for metals dissolution from minerals. The mechanism of mechanochemical reaction has been investigated using solid analyses and simulations. Structural changes caused by mechanochemical reaction are not yet sufficiently clarified because the ground samples are amorphous. The objective of this study was to analyze structural changes of cerianite in weathered residual rare earth ore by mechanochemical reduction. Structural change was analyzed by x-ray absorption near-edge structure and extended x-ray absorption fine structure analysis at the cerium L_III- and K-edges. These analyses revealed that the structural change of cerianite in this ore induced by mechanochemical reduction involved oxygen vacancy production. The process of the oxygen vacancy formation was closely coupled with the quantum effect of localization–delocalization of the 4f electron of cerium.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

Herpesviridae is a family of enveloped double-stranded DNA viruses that cause a wide range of diseases in hosts. Among the various components of herpesvirus particles, tegument proteins residing between the envelop and nucleocapsid play crucial roles in viral replication, immune evasion, and modulation of host cellular pathways. Understanding the three-dimensional structure of herpesvirus tegument proteins help to reveal the molecular mechanism underlying the crosstalk with other viral and cellular components, and thus is crucial for the investigation of their biological and pathological functions. In this review, we summarize the current knowledge of the structural features of herpesvirus tegument proteins, highlighting the structure-based functional implications, including the potential as targets for antiviral drug development.

Hong Kong was under strike from Super Typhoon Saola (2309), necessitating the issuance of the highest tropical cyclone warning signal. Saola skirted past the south-southwest of Hong Kong, bringing hurricane force winds and significant storm surge. Saola had its closest approach to Hong Kong on 1 September 2023, posing a unique challenge in forecasting and early warning for the commencement date of the new school term, where higher impact to traffic and public safety was anticipated. This paper covers the challenges on the forecasting aspect of the super typhoon. The predicted tropical cyclone track, intensity and wind structure are reviewed. Experience in this case showed that while there was not a perfect numerical weather prediction model in terms of the forecast track, intensity and wind structure of Saola, multi-model approach provided very use-ful and crucial information for operational weather warning services.

: Extra- and intra-cellular activity occurs under the direction of numerous inter-molecular interactions, and in any tissue or cell, molecules are densely packed, thus promoting those molecular interactions. Galectins and chemokines, the focus of this review, are small, protein effector molecules that mediate various cellular functions, in particular cell adhesion and migration, as well as cell signaling/activation. In the past, researchers have reported that combinations of these (and other) effector molecules act separately, yet sometimes in concert, but nevertheless physically apart and via their individual cell receptors. This view that each effector molecule functions independently of the other limits our thinking about functional versatility and cooperation, and, in turn, ignores the prospect of physiologically important inter-molecular interactions, especially when both molecules are present or co-expressed in the same cellular environment. This review is focused on such protein-protein interactions with chemokines and galectins, their homo- and hetero-oligomeric structures that they can form, and the functional consequences of those paired interactions.

Ethylene is an ideal CO2 product in an electrocatalytic CO2 reduction reaction (CO2RR), which has high economic value. In this paper, Al–doped octahedral Cu2O (Al–Cu2O) catalyst was synthesized by a simple wet chemical method. The selectivity of CO2RR products was improved by doping Al onto the surface of octahedral Cu2O by regulating the Al content. The Al–Cu2O was used as an efficient electrocatalyst for CO2RR with selective ethylene production. The Al–Cu2O exhibited a high Faradic efficiency (FEC2H4) of 44.9% at -1.23 V (vs. RHE) in CO2 saturated 0.1 M KHCO3 electrolyte. Charge transferring from Al atom to Cu atom take place after Al doping in Cu2O, thereby optimizing the electronic structure, which facilitates CO2RR to ethylene production. The DFT calculation showed that the Al–Cu2O catalyst can effectively reduce the adsorption energy of the *CHCOH intermediate and promote the mass transfer of charges, thus improving the FEC2H4. After Al doping into Cu2O, the center of d orbitals shift positively, which makes the d–band closer to the Fermi level. Furthermore, the density of electronic states increases, which was conducted to the interaction between Cu atoms and intermediates, thus accelerating the electrochemical CO2 reduction process. This work proved that the metal doping strategy can effectively improve the catalytic properties of Cu2O, thus providing a useful way for CO2 cycling and green production of C2H4.

The composition, structure and functionalities of prolamins from highland barley was investigated. These parameters of was compared with the widely applied prolamins (zein). There are more charged and hydrophilic amino acids in prolamins from highland barley than zein. The molecu-lar weight of prolamins from highland barley were between 30 to 63 kDa, which was larger than zein (20 to 24 kDa). β-turn helices is the main secondary structure in prolamins from highland barley, while α-helical structure is the main secondary structure in zein. The water holding capacity, thermal stability, emulsifying capacity and stability of prolamins from highland barley is quite lager than zein, while opposite results can be observed for oil absorption capacity. The diameter of fibers prepared with prolamins from highland barley was almost 6 times that of zein, while ribbon structures rather than fibers were formed by prolamins from highland barley. The results would provide the guidance for application of prolamins from highland barley.

Montes de María is the best-preserved tropical dry forest fragment in the Colombian Caribbean, making it an ideal location for studying the impacts of human disturbance on local ecosystems. This study analyzed the ecological structure of diurnal butterflies in both forested and disturbed areas using 16 circular plots to identify relationships between alpha and beta diversity, and the geographic distance between disturbed areas and native forests, using a range of metrics, including range-abundance and rarefaction curves, nonlinear models, and the Bray–Curtis dissimilarity index. Results revealed three distinct species assemblages associated with forest, intermediate disturbed areas (IDA), and disturbed areas (DA). Nonlinear models show that IDA are more diverse than forest and DA. However, forests have more beta diversity among plots than IDA and DA. Indicator species for each butterfly assemblage were also identified. Thus, although new butterfly species assemblages emerge from a new human land-scape, it is clear that species that only occur within dry forest fragments are lost when forest fragments disappear. Overall, these findings have important implications for conservation efforts and understanding how human disturbance affects biodiversity in tropical ecosystems.

Epstein-Barr virus (EBV)-encoded RNAs (EBERs) are structurally conserved small, noncoding RNAs constitutively expressed in EBV infection. Although primarily localised in the nucleus, EBERs are found in the cytoplasm and exosomes. However, the mechanism(s) of EBERs transport is not known. This study aimed to investigate the structural impact of EBER1 on its transport. EBER1 stem-loop (SL) deletion mutants (ΔSL1, ΔSL3 and ΔSL4) were created and stably transfected into HEK293T cells. The expression of EBER1 was quantified in total cell, nuclear, cytoplasmic and exosomal fractions. The quantification was performed in the presence of physiological expression of RPL22 and La, and after silencing them. These proteins are believed to be involved in EBER1 transport and secretion. Compared to the wildtype EBER1 transfectants, the expression level of EBER1 gene in all mutants was significantly lower in the total cell, cytoplasmic and exosomal fractions. However, ΔSL3 mutant showed significant nuclear retention. Silencing RPL22 resulted in increased nuclear-cytoplasmic trafficking of EBER1. Silencing La protein did not affect EBER1 secretion. Alternatively, the store-operated intracellular Ca2+ was found to correlate with EBER1 expression in exosomes. Taken together, EBER1 structure and its interaction with RPL22 appeared to be important in the nuclear-cytoplasmic transport of the RNA.

Bunyaviruses represent the largest group of RNA viruses, and are the causative agent of a variety of febrile and hemorrhagic illnesses. Originally characterized as a single serotype in Africa, the number of described bunyaviruses now exceeds over 500, with its presence detected around the world. These predominantly tri-segmented, single-stranded RNA viruses are transmitted primarily through arthropod and rodent vectors, and can infect a wide variety of animal and plants. Although encoding for a small number of proteins, these viruses can inflict potentially fatal disease outcomes, and have even developed strategies to suppress the innate antiviral immune mechanisms of the infected host. This short review will attempt to provide an overall description of the order Bunyavirales, describing the mechanisms behind their infection, replication and their evasion of the host immune response. Furthermore, the historical context of these virus will be presented, starting from their original discovery almost 80 years ago, to the most recent research pertaining to viral replication and host immune response.

The present work reports on the calculated electronic and magnetic structure of the binary Co-Ga system at high Co content. β-CoGa adopts a simple cubic CsCl type structure. Well-ordered CoGa does not exhibit collective magnetism but is a paramagnetic, metallic compound. Neither Co nor Ga deficiency induces magnetic order, however, ferromagnetism is observed for Co-Ga anti-site disorder. The magnetic moment per cell increases up to about 1.2 μB in the completely disordered body centered cubic structure. With increasing Co content, Co1+xGa1−x maintains the CsCl type structure and becomes ferromagnetic. Most important, a discontinuity of the magnetic order with composition is observed at about 10% excess Co, where a change from a low magnetic moment state to a high moment state is observed. This is accompanied by a change in the electronic structure and transport properties. The discontinuity is forced by the increasing exchange splitting related to the localized moment of the additional Co atoms that replace Ga. Subsequently, the magnetic moment increases continuously up to 2.5 μB for x=0.6. For x≳0.6, the structure changes to face centered cubic with random site occupation and the magnetic moment further increases. Above the magnetic discontinuity, the Curie temperature increases linearly with the Co content from the onset of ferromagnetism, until it reaches its maximum in pure Co.

A model for parasitic motility has been proposed in which parasite filamentous actin (F-actin) is attached to surface adhesins by a large component of the glideosome, known as the glideosome-associated connector protein (GAC). This large 286 kDa protein interacts at the cytoplasmic face of the plasma membrane with the phosphatidic acid-enriched inner leaflet and cytosolic tails of surface adhesins to connect them to the parasite actomyosin system. GAC is observed initially to the conoid at the apical pole and re-localised with the glideosome to the basal pole in gliding parasite. GAC presumably functions in force transmission to surface adhesins in the plasma membrane and not in force generation. Proper connection between F-actin and the adhesins is as important for motility and invasion as motor operation itself. This notion highlights the need for new structural information on GAC interactions, which has eluded the field since its discovery. We have obtained crystals that diffracted to 2.6-2.9 Å for full-length GAC from Toxoplasma gondii in native and selenomethionine-labelled forms. These crystals belong to space group P212121, cell dimensions are roughly a=119 Å, b=123Å, c=221Å, α=90, β=90, γ=90 with 1 molecule per asymmetric unit, suggesting a more compact conformation than previously proposed.

Graphite nanoplatelets (GNPs) were produced from flake graphite that had been immersed in isopropyl alcohol solution (70%) and converted to powder form in an ultrasonic bath (5 h, room temperature). Scanning and transmission electron microscopy, X-ray diffractometry, and Raman spectroscopy identified 120-nm-thick GNP crystallites and 0.5–21 µm plates with different areas and shapes. Extensive exfoliation was observed by transmission electron microscopy with abundant multilayer and some monolayer GNPs. X-ray diffractometry confirmed 43 GNP layers along the c-axis. Raman spectroscopy indicated well-defined GNPs with few defects and no oxide content. Rietveld analysis indicated a GNP crystal lattice with stacks of parallel two-dimensional graphene layers and tightly bound hybridized carbon atoms stacked in a translational …ABAB… sequence in hexagonal rings.