The initiation of micro-cracks in concrete is primarily due to its brittleness, which causes severe impacts on the overall behavior of the concrete. However, incorporating fibers in concrete could significantly improve its mechanical properties. The current study demonstrates the influence of two types of fibers on the mechanical properties of concrete. Nylon Fiber Threads (NFT) and Nylon Fiber Strands (NFS) at a fiber content of 2.5 kg/m³ were incorporated in the concrete mix. Concrete with a compressive strength of 30 MPa and a water-cement ratio of 0.4 was produced to investigate the fresh and mechanical properties of conventional and nylon-fiber reinforced concrete (NFRC). The concrete prims and cylinders were tested for compressive, splitting, and flexural strength using ASTM standards (ASTM C-39, C-496, and D-790, respectively). It was found that NFT-reinforced samples achieved higher mechanical properties of concrete (13.05%) compared to NFS-reinforced samples. Test results showed that incorporation of nylon fibers (NF) in concrete decreased the compressive strength of cylindrical and cubical specimens by 0–10% and 5–15%, respectively. However, it increased the splitting tensile and flexural strengths by 0-15%, and 5-15% respectively. Furthermore, the incorporation of NF in concrete significantly improved the ductility and delayed the crack initiation in concrete.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Fiber reinforced polymer (FRP) is one of the important material used for strengthening and retrofitting of reinforced concrete structures. The commonly used fibers are glass, carbon and aramid fibers. Durability of structures can be extended by selecting appropriate method of strengthening. FRP wrapping is one of the easiest methods for repair, retrofit and maintenance of structural element. Deterioration of structures may be due to moisture content, salt water, or contact with alkali solutions. There is significant effect of permeability, rise in temperature, chemical attack, fatigue action, micro pores on members of structures. Using FRP additional strength can be gained by structural elements. This paper investigates durability of aramid fiber subjected to acid attack and temperature rise. Concrete cubes are prepared as specimens with double wrapping of aramid fibers. Diluted hydrochloric acid solution is used for immersion of specimen for curing period of 7, 30 and 70 days. In case of fire resistance test, such specimens are kept in hot air oven at a temperature of 2000C at different time intervals. The effect of aramid fiber wrapping on compressive strength and weight loss of specimen is studied.

The bending performance of a basalt-polypropylene fiber-reinforced concrete (HBPFRC) was characterized by testing 24 400×100×100 mm3 prismatic specimens in a four-point bending test JSCE-SF4 configuration. The type and content of both fibers was varied in order to guarantee different target levels of post-cracking flexural performance. The results evidenced that mono-micro basalt fiber reinforced concrete (BFRC) allows the increase of the flexural strength (pre-cracking stage), while macro polypropylene fiber reinforced concrete can effectively improve both bearing capacity and ductility of the composite for a wide crack width range. Compared with the plain concrete specimens, flexural toughness and equivalent flexural strength of macro polypropylene fiber-reinforced concrete (PPFRC) and the hybrid fiber-reinforced concrete (HFRC) increased by 3.7~7.1 times and 10%~42.5%, respectively. From both technical and economic points of view, the optimal mass ratio of basalt fiber to polypropylene fiber resulted to be 1:2, with a total content of 6 kg/m3. This HFRC is seen as a suitable material to be used in sewerage pipes where cracking control (crack formation and crack width control) is of paramount importance to guarantee the durability and functionality of the pipeline as well as the ductility of the system in case of local failures.

Adding steel fibers to concrete improves the capacity in tension-driven failure modes. An example is the shear capacity in steel fiber reinforced concrete (SFRC) beams with longitudinal reinforcement and without shear reinforcement. Since no mechanical models exist that can fully describe the behavior of SFRC beams without shear reinforcement failing in shear, a number of empirical equations have been suggested in the past. This paper compiles the existing empirical equations and code provisions for the prediction of the shear capacity of SFRC beams failing in shear as well as a database of 487 experiments reported in the literature. The experimental shear capacities from the database are then compared to the prediction equations. This comparison shows a large scatter on the ratio of experimental to predicted values. The practice of defining the tensile strength of SFRC based on different experiments internationally makes the comparison difficult. For design purposes, the code prediction methods based on the Eurocode shear expression provide reasonable results (with coefficients of variation on the ratio of tested to predicted results of 27% - 29%). None of the currently available methods properly describe the behavior of SFRC beams failing in shear. As such, this work shows the need for studies that address the different shear-carrying mechanisms in SFRC and its crack kinematics.

In this study, experimental work was carried out on reinforced concrete (RC) beams strengthened with carbon fiber reinforced polymers (CFRP) plates. This study aims to examine the effect of the reinforcement ratio on the flexural behavior of these beams and propose a new model for predicting the debonding moment. Six RC beams consisting of three control beams and three beams strengthened with CFRP plates were tested. The beams were simply supported and loaded with four-point bending. The test variable was the tensile reinforcement ratio (1%, 1.5%, and 2.5%). Analytical prediction using the fiber element method was also carried out to obtain the complete theoretical response of the beam due to flexural loads. The test results show that the reinforcement ratio affected the bending performance of RC beams with CFRP plates. Following this, the experimental data from 60 beam test results from published literature and this study were analyzed. From these data, it was found that the ratio of tensile reinforcement, the ratio of modulus of elasticity of concrete, the modulus of elasticity of the plate, and plate thickness all affect the value of debonding moment. A parametric study using fiber element and two-dimensional finite element method was also carried out to confirm the effect of these parameters on debonding failure. These parameters were then used to develop an equation to predict the debonding moment of RC beams strengthened with CFRP plates using simple statistical analysis. This analysis resulted in a simple model for predicting the debonding moment. Then the model is entered into a computer program, and the complete response of the cross-section due to debonding failure can be obtained.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

This paper presents the systematic development and performance characterization of a non-proprietary 3D-printable ultra-high-performance fiber-reinforced concrete (UHPFRC) for digital construction. Several fresh and hardened properties of the developed 3D-printable UHPFRC matrix (without fiber) and composite (with 2% volume fraction of steel fibers) were evaluated and compared to that of conventionally mold-cast UHPFRC. Additionally, the effects of testing direction on the compressive and flexural strengths of the printed UHPFRC were investigated. The fresh properties of the UHPFRC developed in this study satisfied the criteria for extrudability, buildability, and shape-retention-ability, which are relevant for ensuring printability. The printed UHPFRC exhibited superior flexural performance to the mold-cast UHPFRC due to alignment of the short fibers in the printing direction. The high compressive and flexural strengths, along with the deflection-hardening behavior, of the developed UHPFRC can enable the production of thin 3D-printed components with significant reduction or complete elimination of conventional steel bars.

Although working memory (WM) is crucial for intellectual abilities, not much is known about its brain underpinnings, especially the structural connectivity. We used diffusion tensor imaging (DTI) to look across the whole brain for the white matter integrity correlates of the individual differences in the reading span (verbal WM capacity during reading) in healthy adults. Right-handed healthy native Russian speakers (N = 67) underwent DTI on a 3T Philips Ingenia scanner. Verbal WM was assessed with the Daneman-Carpenter reading span test (Russian version). Fractional anisotropy maps from each participant were entered into the group tract-based spatial statistics analysis with the reading span as a covariate; the results were TFCE-corrected. After taking into account effects of age, sex, education and handedness, reading span positively correlated with the white matter integrity in multiple sites: the body, the genu and the splenium of corpus callosum; bilateral corona radiata (anterior, posterior, and superior); bilateral superior longitudinal fasciculus; several tracts in the right hemisphere only, including the internal and external capsule; bilateral superior parietal and frontal white matter. Although the left hemisphere is central for verbal processing, we revealed the important role of the right hemisphere white matter for the verbal WM capacity. Our finding indicates that larger verbal working memory span may originate from additional processing resources of the right hemisphere.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

The opened beams always confused the designers due to the guidelines missing. In this research, six hybrid reinforced beams reinforced with mixed steel and basalt fiber reinforced polymer (BFRP) bars had constant cross-sections of 150mm x 300mm and a clear span of 1800mm. Generally, five beams have symmetrical rectangular openings with dimensions of 150mm x 250mm located at a distance of 250mm (equivalent to the beam effective depth) from the beam support in addition to a solid beam that is served as a control reference. The studied parameters included the effect of using internal reinforcement (steel or BFRP bars) provided along the opening or by incorporating an external BFRP sheet around the opening corners. Also, the conduction of double enhancement with internal steel reinforcement bars further external strengthening BFRP sheet was investigated. The relevant results showed that the opened beam without enhancement lost almost 74.66% of the maximum load compared with the solid beam. Placing internal steel or BFRP bars around the openings increased the maximum load by 62.07% and 59.68%, respectively in comparison to the non-enhanced opened beams. Using an external BFRP sheet to strengthen the opening corners of the beam enhanced the maximum load by 76.39% compared with the non-enhanced opened beam. Therefore, if the beam double enhancement with an external BFRP sheet and internal steel reinforcement around the openings, the maximum load increased by 137.40% compared with the non-enhanced opened beam. Ultimately to further analyze the experimental results and confirm their findings, the study was extended to include the numerical analysis using three dimensional finite element modeling and the results correlated very well with the experimental ones.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

Hybrid fiber reinforced composites can be controlled by price, weight and various mechanical properties depending on fiber ratio and lamination method. Despite these excellent hybrid properties, there is a disadvantage that inter-laminar fracture due to external impact, which is the biggest weakness of fiber reinforced composite materials, is weak. The test specimens were prepared by using a vacuum bag method, which is manufactured by using an autoclave device. The pre-preg is manufactured in the form of a B-stage. In the process of fabricating the nanoparticle pre-preg, the homogeneizer using an ultrasonic wave was used to disperse the epoxy subject without the curing agent into nanoparticles. The dispersion of the nanoparticles was dispersed by the weight of the epoxy resin. This is to take into account the cohesion of HNT and to understand the range of cohesion of HNT in a matrix with viscosity and its phenomenon. According to the Comparison of the interlayer interfacial properties and mechanical properties of Aramid / Basalt fiber hybrid composites by HNT addition, the fracture toughness, ILSS and bending strength of specimens with HNT content of more than a certain level were decreased because of the aggregation of HNT.

Extinction of natural resources builds up pressure on governments to invest in research to find more sustainable resources for construction sector. Earlier studies on mortar and concrete show that bottom ash and basalt fiber are independently alternative binder in the concrete sector. This study aims to use bottom ash and basalt fiber blends as alternative novel-based composites in pure cement paste. Strength and durability properties of two different percentages of bottom ash (40% and 50%) and three volume fractions of basalt fiber (0.3%, 0.75%, and 1.5%) were used at three curing periods (7, 28, and 56 days). In order to measure physical properties of the basalt-reinforced bottom ash cement paste composites flowability, dry unit weight, porosity and water absorption measurements at 7, 28, and 56 days of curing were performed. Furthermore, mechanical properties of composites determined by unconfined compressive strength and flexural strength tests. Finally, to assess the durability sulfate-resistance and seawater-resistance tests have been performed on composites at 28 and 56 days of curing. Results showed that addition of basalt fiber improves physical, mechanical and chemical stability properties of paste up to a limiting basalt fiber addition (0.3% volume fraction) where above an adverse effect have been monitored. It is clear that observed results can lead to development of sustainability strategies in the concrete industry by utilizing bottom ash and basalt fiber as an alternative binder.

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

Improper lifting measures of long-span spatial steel structures during construction process may delay the construction period and even cause safety accidents. Few studies on long-span spatial steel structures considered time-varying mechanical characteristic during construction process. In order to achieve safe and efficient installation in a long-span spatial steel structure, this research presents a time-varying mechanical analysis of the synchronous and asynchronous integral lifting and a single and interlaced point’s asynchronous integral lifting analysis method of a long-span spatial steel structure. The results showed that in the case of asynchronous lifting of single point, the displacement influence on other members is related to the distance. The closer the distance from the lifting point, the greater the influence. In asynchronous integral lifting, the lifting point with large lifting force is first installed to the specified position, and the lifting point with small lifting force is installed to the specified position.

One of the non-linear phenomena that affect high bandwidth and long reach communication systems is the non-linear phenomenon called four-wave mixing (FWM). Unfortunately, the simulation of such systems aiming to obtain their design parameter limitations require more time as the number of channels increases. In this paper, we propose a new high-performance computational model to obtain optimal design parameters in a multi san Dense Wavelength Division Multiplexing (DWDM) system, limited by FWM and the intrinsic Amplified Spontaneous Emission (ASE) noise of optical amplifiers employed in each segment. The simulation in this work provides a complete optical design characterization and compares the efficiency and speed improvement of the proposed parallelization model versus a previous sequential model. Additionally, an analysis of the computational complexity of parallel model is presented, where two parallel implementations are used. First, Open Multi−Processing (OpenMP), based on the use of a central, multi-core processing unit is used and secondly the Compute Unified Device Arquitecture (CUDA), which is based on the use of graphics processing unit. Results show that parallelism improves to up to 40 times the performance of the simulation when nested parallelization with CUDA is used, over de sequential method and up to 6 times compared with the implementation with OpenMP using 12 processors. Within our parallel implementation, it is possible to simulate with an increased number of channels, that was unpractical in the sequential simulation.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

Abstract: This study was aimed to determine the influence of the volume fraction of steel fibers and on fracture parameters of concrete. Fifty notched steel fiber reinforced concrete (SFRC) beams and ordinary concrete beams with dimensions of 100mm×100mm×515mm were cast and tested via three-point bending test. Among them, the type of steel fiber is milling type (MF), and the volume fraction of steel fiber added is 0%, 0.5%, 0.5%, 1.5%, 1.5%, 2%, respectively. The effects of the steel fiber volume fraction (VF) on the critical stress intensity factor (KIC), fracture energy (GF), the deflection at failure(δ0), the critical crack mouth opening displacement (CMODC) and the critical crack tip opening displacement (CTODC)were studied. Through the analysis of test phenomena and test data such as load-deflection (P-δ) curve, load-crack mouth opening displacement (P-CMOD) curve and load-crack tip opening displacement (P-CTOD) curve following conclusions are drawn: With the increase of steel fiber volume fraction, some fracture parameters increase gradually and maintain a certain linear growth. The gain ratio of fracture parameters increases significantly, and the gain effect is obvious. Through this law of growth, the experimental statistical formulas of fracture energy and critical stress intensity factor are summarized.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer com-posites are being considered as alternative materials in the automobile industry. Rapid impregnation of the resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manu-facturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed

Thermoplastic pultrusion is a suitable process for fabricating continuous unidirectional thermoplastics with a uniform cross-section, high mechanical properties due to continuous fiber reinforcement, low cost, and suitability for mass production. In this paper, jute and glass fibers were reinforced with a polypropylene matrix and fabricated using the thermoplastic pultrusion process. The volumetric fraction of the composite was designed by controlling the filling ratio of the reinforcing fiber and matrix. The effects of molding parameters were investigated, such as pulling speed and molding temperature, on the mechanical properties and microstructure of the final rectangular profile composite. The pulling speed and molding temperature were varied from 40 to 140 mm/min and 190 to 220°C, respectively. The results show that an increase in molding temperature initially led to an increase in mechanical properties, up to a certain point. Beyond that point, they started to decrease. The increase in molding temperature also led to an increase in void content. Meanwhile, un-impregnation decreased with the increase in molding temperature, and the jute fiber began to degrade at high temperatures. In the next step, with varying pulling speed, the mechanical properties decreased as the pulling speed increased, with a corresponding increase in void content and un-impregnation. The decrease in mechanical properties was influenced by the increase in void content and un-impregnation, as the jute fiber degraded at higher temperatures.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

A multiscale modelling approach was developed in order to estimate the effect of defects on the strength of unidirectional carbon fiber composites. The work encompasses a micromechanics approach, where the known reinforcement and matrix properties are experimentally verified and a 3D finite element model is meshed directly from micrographs. Boundary conditions for loading the micromechanical model are derived from macroscale finite element simulations of the component in question. Using a microscale model based on the actual microstructure, material parameters and load case allows realistic estimation of the effect of a defect. The modelling approach was tested with a unidirectional carbon fiber composite beam, from which the micromechanical model was created and experimentally validated. The effect of porosity was simulated using a resin-rich area in the microstructure and the results were compared to experimental work on samples containing pores.

Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

As Chronic Non-Communicable Diseases (CNCD) increase, preventive approaches become more crucial. In this review, Calorie Restriction (CR) effects on human beings were evaluated, comparing benefits and risks of different CR diets: classic CR vs ketosis-inducing diets, including Intermittent Fasting (IF), Classic Ketogenic Diet (CKD), Fasting Mimicking Diet (FMD), Very-Low-Calorie Ketogenic Diet (VLCKD) and Spanish Ketogenic Mediterranean Diet (SKMD). Special emphasis on Insulin Resistance (IR) was placed, as it mediates Metabolic Syndrome (MS), a risk factor for CNCD, and predicts MS diagnosis. CR is the most robust intervention known to increase lifespan and health span, with high evidence and known biochemical mechanisms. CR improves cardiometabolic risk parameters, boosts exercise insulin sensitivity response, and there may be benefits of implementing moderate CR on healthy young and middle-aged individuals. However, there is insufficient evidence to support long-term CR. CKD is effective for weight and MS management, and may have additional benefits such as prevention of muscle loss and appetite control. SKMD has extreme significance benefits for all the metabolic parameters studied. Studies show inconsistent benefits of IF compared to classic CR. More studies are required to study biochemical parameters, reinforce evidence, identify risks, and seek effective and safe nutritional CR approaches.

3D printing with cement-based materials is a promising manufacturing technique for civil engineering applications that already allows for the design and the construction of complex and highly customized structures using a layer-by-layer deposition approach. Usually, in this type of additive manufacturing, a mixture of cement, water, aggregate and additives is extruded through a specific print head and deposited in successive layers to form the desired shape. The extrusion mechanism is one of the most expensive parts of the 3D printer. Also, for low scale 3D printers, based on the shape of the extruder and the geometry limitation of the mixing blade, the 3D mixture is often limited to a narrow range of materials due to the risk of layer splitting or blockage. Therefore, there is a need to develop affordable and feasible alternatives to the current design-fabrication-application approach of 3D printers. In this paper, various new designed mixtures of fiber reinforced mortars that can be 3D printed using only a commercially available screw pump are analyzed based on their fresh properties and mechanical characteristics. The reduced facility requirements in this approach allow 3D-printing to be more available for civil engineering applications. With further innovation in the future, this method and mixtures can be extended for sustainable and economically feasible printing of single-family housing units.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Optical fiber sensors have become a widely-used tool to perform life-long monitoring of large structures. Different set-ups of sensors can be used to obtain information at different scopes. In this paper, the application of a portable Brillouin optical time domain analysis sensor applied to reinforced concrete beams is presented. The sensor is made up of a single-mode optical fiber applied to the structure that enables the measurement of tensile and compressive axial strain along the beams. The fiber is embedded into a concrete casting and fixed along the reinforcement bars so that a complete correlation can be obtained regarding strain and displacements in linear and non-linear flexural response. The use of four sensing fibers positioned along the beam's length at different vertical positions makes it possible to read the strain variation within the cross-section. In accordance with Bernoulli’s hypothesis, this allows curvature diagrams to be obtained across the structure. The measured curvature is used to set up the moment–curvature relationship, which highlights the possibility of the sensor monitoring structures continuously in space and time.

For the numerical simulation of components made of short fiber-reinforced composites the correct prediction of the deformation including the elastic and plastic behavior and its spatial distribution is essential. When using purely deterministic modeling approaches the information of the probabilistic microstructure is not included in the simulation process. One possible approach for the integration of stochastic information is the use of random fields. In this study numerical simulations of tensile test specimens are conducted utilizing a finite deformation elastic-ideal plastic material model. A selection of the material parameters covering the elastic and plastic domain are represented by cross-correlated second-order Gaussian random fields to incorporate the probabilistic nature of the material parameters. To validate the modeling approach tensile tests until failure are carried out experimentally, that confirm the assumption of spatially distributed material behavior in both the elastic and plastic domain. Since the correlation lengths of the random fields cannot be determined by pure analytic treatments, additionally numerical simulations are performed for different values of the correlation length. The numerical simulations endorse the influence of the correlation length on the overall behavior. For a correlation length of 5mm a good conformity with the experimental results is obtained. Therefore, it is concluded, that the presented modeling approach is suitable to predict the elastic and plastic deformation of a set of tensile test specimens made of short fiber-reinforced composite sufficiently.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

The brain being arguably the most complex organ in the human body, its detailed functioning is yet to be fully deciphered, let alone accurately modeled. Nonetheless, the medical community has gathered quite a remarkable amount of studies about the consequences of illnesses and injuries on its development and functioning. This bibliographic review aims to cover mostly the findings related to the changes in the physical distribution of neurons and their connections - the connectome -, both structural and functional, as well as their modelling. It does not intend to offer an extensive medical description of all injuries and diseases affecting the brain, rather presenting the most common ones succinctly so the need for accurate brain modelling can be fully understood and pondered, offering propositions to this aim.

Abstract This study focuses on the toxicity assessment of various flavonoids, with particular emphasis on Hesperidin. Among the investigated compounds, Hesperidin exhibits notable potential and low toxicity in both short and long-term evaluations. The toxicity parameters for Hesperidin include a low Max. Tolerated Dose (Human) (0.525 log mg/kg/day), indicative of its minimal potential harm to humans. Additionally, its Oral Rat Acute Toxicity (LD50) (2.506 mol/kg) suggests a relatively low acute toxicity level. The Oral Rat Chronic Toxicity (LOAEL) (3.167 log mg/kg_bw/day) signifies a higher dose threshold for observing adverse effects over the long term. Furthermore, Hesperidin demonstrates low Minnow Toxicity (7.131 log mM), suggesting minimal impact on aquatic organisms. Overall, this comprehensive assessment positions Hesperidin as a promising flavonoid with favorable properties and minimal toxicity.

The purpose of this study was to conduct a meta-analysis that shows the influence of fiber on ultimate compressive strength and tensile strength of ultra-high performance concrete. The internet scholarly search engines and ScienceDirect article references were used to illustrate the papers concerning the experimental investigations of mechanical properties of ultra-high strength concrete with and without fiber with clearly, completely and comparative raw data. The normal concrete test results were dismissed from this search. Seven trials were identified based on the adopted inclusion and exclusion criteria above. The meta-analysis based on standardized mean difference was carried out on the basis of a fixed-effects model for the major outcomes of the ultimate compressive and tensile properties of ultra-high performance concrete. A total of 888 test specimens were enrolled in these seven trials. The combined analysis yielded a sign of a significant improvement in ultimate compressive strength and tensile strength of ultra-high strength concrete with fiber addition of 2% by concrete volume. The summary effect size of ultimate compressive strength was 2.34 while a more improvement in term of tensile strength with effect size of 2.64. By addition fiber of 2% provides a significant benefit in mechanical properties of ultra-high performance concrete.

Electromobility has gained significant attention in the auto- motive industry, with car manufacturers striving to improve the charging experience for their users. In this study, we compare multiple realistic charging strategies in order to quantify the benefits arising from better planning of charging sessions. We base our evaluation on electricity price data from three regions: Sweden (SE3 region), Germany (DE region), and Denmark (DK2 region). This data is obtained from the ENTSO-E Transparency Platform, covering the two full years 2021 and 2022. We enhance this dataset with commercial price forecasts from the company StormGeo and benchmark it against a naive forecasting method. The primary aim of our work is to compare how the strategies of varying levels of complexity perform across the three different countries in terms of minimizing energy costs for electric car users.

In this work, several random Boolean networks (RBN) are generated and analyzed from two characteristics: their time evolution diagram and their transition diagram. To do this, its randomness is estimated using three metrics, of which algorithmic complexity is the only one capable of revealing both transitions towards the chaotic regime and the algorithmic contribution of certain states to the transition diagram and their relationship with the order they occupy in the temporal evolution of the respective RBN.

Fiber reinforced thermoplastics (FRTP), which is reinforced with glass or carbon fibers, are used to improve the mechanical strength of injection-molded products. However, FRTP has problems such as the formation of weld lines, the deterioration of the appearance due to the exposure of fibers on the molded product surface, and the deterioration of the strength of molded products due to the fiber orientation in the molded products. We have designed and fabricated an injection mold capable of melt flow control and induction heating and cooling that has the functions of both heating and cooling the injection mold as well as the function of controlling the melt flow direction using a movable core pin. In this study, the above-mentioned mold was used for the molding of carbon fiber reinforced semi-aromatic polyamide. As a result, we found that increasing the heating temperature of the mold and increasing melt flow control volume contribute to the prevention of the generation of a weld line and the exposure of fibers on the molded product surface, as well as to the formation of a flat surface and increased bending strength. The relationships of these results with the carbon fiber orientation in the molded products and the crystallization of semi-aromatic polyamide were also examined in this study.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

Microplastics (plastic particles &lt; 5 mm) are ubiquitous pollutants that pose the ability to carry microbiota, including pathogens. Microbial adhesion is usually a sign of pathogenicity, thus we investigated the adherent strains found on 4 mm nylon strips, which were ingested and excreted by wild fish specimens. Polymer analysis of the excreted samples shown no signs of degradation, nor have their controls, represented by the nylon strips submerged in the same water tanks. Both the ingested samples and controls presented pathogens in large numbers, revealing the fact that nylon microplastics can be physical carriers for pathogens in the aquatic environment.

Microplastics (MPs) quantification in benthic marine sediments is typically performed by time-consuming and moderately accurate mechanical separation and microscopy detection. In this paper we describe the results of our innovative Polymer Identification and Specific Analysis (PISA) of microplastic total mass, previously tested on either less complex sandy beach sediment or less demanding (because of the high MPs content) wastewater treatment plant sludges, applied to the analysis of benthic sediments from a sublittoral area north-west of Leghorn (Tuscany, Italy). Samples were collected from two shallow sites characterized by coarse debris in a mixed seabed of Posidonia oceanica, and by a very fine silty-organogenic sediment, respectively. After sieving at &lt;2 mm the sediment was sequentially extracted with selective organic solvents and the two polymer classes polystyrene (PS) and polyolefins (PE and PP) were quantified by pyrolysis-GC/MS. A contamination in the 8-65 ppm range by PS could be accurately detected. Acid hydrolysis on the extracted residue to achieve total depolymerization of all natural and synthetic polyamides, tagging of all aminated species in the hydrolyzate with a fluorophore, and reversed-phase HPLC (RP-HPLC) analysis, allowed to quantify within the 137-1523 ppm range the individual mass of contaminating Nylon 6 and Nylon 6,6, based on the detected amounts of the respective monomeric amines 6-aminohexanoic acid (AHA) and hexanediamine (HMDA). Finally, alkaline hydrolysis of the residue from acid hydrolysis followed by RP-HPLC analysis of the purified hydrolysate showed contamination by polyethylene terephthalate (PET) in the 12.1-2.7 ppm range, based on the content of its comonomer, terephthalic acid.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode~2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

We prove through path integral Monte Carlo computer experiments that the affine quantization of the $\varphi_4^4$ scaled Euclidean covariant relativistic scalar field theory is a valid quantum field theory with a well defined continuum limit of the one- and two-point-function. Affine quantization leads to a completely satisfactory quantization of field theories using situations that involve scaled behavior leading to an unexpected, $\hbar^2/\varphi^2$ which arises only in the quantum aspects.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

The Semantic-Enhanced Tree-LSTM (SeT-LSTM) network, a novel advancement in the realm of linguistic modeling, marks a significant step forward from traditional Tree-based Long Short Term Memory (LSTM) networks. By intricately weaving in the nuances of typed grammatical dependencies, SeT-LSTMs offer a more nuanced understanding of language semantics. Traditional models often overlook the semantic shift caused by variations in word or phrase roles, a gap this paper aims to fill by focusing on the types of grammatical connections, or typed dependencies, within sentences. Our proposed architecture, dubbed the Semantic Relationship-Guided LSTM (SRG-LSTM), leverages a control mechanism to model the interplay between sequence elements. Additionally, we present a novel Tree-LSTM variant, the Semantic Dependency Tree-LSTM (SDT-LSTM), which integrates dependency parse structures with dependency types for more robust sentence embedding. The SDT-LSTM demonstrates superior performance in Semantic Relatedness Scoring and Sentiment Analysis compared to its predecessors. Qualitatively, it shows resilience to changes in sentence voice and heightened sensitivity to nominal alterations, aligning well with human intuition. This research underlines the pivotal role of grammatical relationships in sentence understanding and paves the way for further exploration in this domain.

The novel coronavirus disease (COVID-19) pandemic has resulted in over 720 million confirmed cases and 7 million deaths worldwide, with insufficient treatment options. Innumerable efforts are being made around the world for faster identification of therapeutic agents to treat the deadly disease. Postacute sequelae of SARS-CoV-2 infection or COVID-19 (PASC), also called Long COVID, is still being understood and lacks treatment options as well. A growing list of drugs are being suggested by various in silico, in vitro and ex vivo models, however currently only two treatment options are widely used: the RNA-dependent RNA polymerase (RdRp) inhibitor remdesivir, and the main protease inhibitor nirmatrelvir in combination with ritonavir. Computational drug development tools and in silico studies involving molecular docking, molecular dynamics, entropy calculations and pharmacokinetics can be useful to identify new targets to treat COVID-19 and PASC, as shown in this work and our recent paper that identified alendronate as a promising candidate. We have now investigated all bisphosphonates which can bind competitively to nidovirus RdRp-associated nucleotidyl (NiRAN) transferase domain, and systematically down selected seven candidates (CHEMBL608526, CHEMBL196676, CHEMBL164344, CHEMBL4291724, CHEMBL4569308, CHEMBL387132, CHEMBL98211), two of which closely resemble the approved drugs minodronate and zoledronate. This work and our recent paper together provide an in silico mechanistic explanation for alendronate and zoledronate users having dramatically reduced odds of SARS-CoV-2 testing, COVID-19 diagnosis, and COVID-19-related hospitalizations, and indicate that similar observational studies with minodronate could be valuable.

In small animal models of severe acute respiratory syndrome coronaviruses (SARS-CoV and SARS-CoV-2) infection, ferrets (Mustela putorius furo) have been used to investigate the pathogenesis. Podoplanin (PDPN) is an essential marker in lung type I alveolar epithelial cells, kidney podocytes, and lymphatic endothelial cells. Monoclonal antibodies (mAbs) against ferret PDPN (ferPDPN) are useful for the pathological analyses of those tissues. We previously established an anti-ferPDPN mAb, PMab-292 using the Cell-Based Immunization and Screening (CBIS) method. In this study, we determined the critical epitope of PMab-292 using flow cytometry. The N-terminal ferPDPN deletion mutants analysis revealed that the Val34 is located at the N-terminus of the PMab-292 epitope. Furthermore, the PA tag-substituted analysis (PA scanning) showed that Asp39 is located at the C-terminus of PMab-292 epitope. The epitope sequence (₃₄-VRPEDD-₃₉) also exists between Val26 and Asp31 of ferPDPN, indicating that PMab-292recognizes the tandem repeat of the VRPEDD sequence of ferPDPN.

This article seeks to strengthen efforts in technological developments based on the classification of PET plastic that positively impacts sustainable development and contributes to suitable solutions in collection centers in Mexico. Three experiment designs and machine learning tools for data processing were developed. For the experimentation, three factors were considered: the bottle's size, the amount of liquids inside the bottle, and the label on the bottle. The first experiment was to identify the distance of the sensor from post-consumer PET bottles. The second experiment was to determine the detection ability of the sensor with different levels of liquids inside the bottles, and the third was to determine the detection ability on the bottle labels. A digital lux meter on a microcontroller was developed to monitor illuminance on post-consumer PET plastic when it contains liquid as it passes through a conveyor belt for processing at an average rate of three bottles per second. With the implemented methodology, liquids were satisfactorily detected inside the transparent PET bottles when they had beverages between 25% and 100% of their capacity. Finally, this paper highlights that it is possible to implement an affordable design to identify bottles with liquids for collection centers.

Electrochemical impedance (EI) measurements were performed to evaluate the nylon 66/-tetra-(para-aminophenyl) porphyrin (H₂T(p-NH₂)PP)/graphene oxide (GO) film coating on stainless steel and compared to the nylon/H₂T(p-NH₂)PP and nylon/GO film samples using 1M H₂SO₄ as electrolyte. The nylon/H₂T(p-NH₂)PP and nylon/GO composite films showed high electrochemical impedance in the order of 109 ohm-cm² and a system controlled by mass transfer, product of a diffusion process at low frequencies with a resistance up to 5 orders of magnitude, indicating the diffusion of protons through the coating and a decrease in the metal dissolution. Otherwise, the nylon/H₂T(p-NH₂)PP/GO film compound evaluated show good ionic conductivity and electrochemical stability in the acid environment, acting porphyrin as a catalyst to the passage of protons through the film, reducing its electrochemical impedance up to 7 orders of magnitude with respect to the compounds nylon/H₂T(p-NH₂)PP and nylon/GO. Likewise, good capacitance values are also shown by modifying the concentrations of porphyrin and GO reinforcing materials. These properties are important for technological applications, such as anticorrosion coating for bipolar plates or membrane in a fuel cell type PEM, super-capacitors, etc.

The ordinary 3D wave equation for nondissipative, homogeneous, isotropic media admits solutions where the point sources are permitted to move, but it does not admit solutions where the receiver is allowed to move. To overcome this limitation, the new wave equation is derived, permitting both the receiver and the source to move. This new wave equation is a generalization of the standard wave equation, and it reduces to the standard wave equation when the receiver is at rest. To derive this new wave equation, we first mathematically define a diverging spherical wave caused by the stationary point source. From this purely mathematical definition, the wave equation for the stationary source and the moving receiver is derived together with the corresponding free-space Green's function. Utilizing the derived Green's function, it was shown that this new wave equation also permits the solutions where both the receiver and the source are permitted to move. In conclusion, this paper demonstrates that, instead of an ordinary wave equation, the wave equation for the moving source and the moving receiver governs the waves emitted by the moving point sources and received by the moving receivers.

The future index prices are viewed as a critical issue for any trader and investor. For this craving, various models have shown up in the literature. The Geometric Brownian motion (GBM) is one of the popular models. This work examines four types of GBM as per the presence of memory or kind of volatility. These models include classical GBM with memoryless and constant volatility assumptions, SVGBM with memoryless and stochastic volatility assumption, GFBM with memory and constant volatility assumption, and SVGFBM with memory and stochastic volatility assumption. These models are utilized in an empirical study to forecast the future index price of Energy Sector in the Saudi Stock Exchange Market. The assessment was led by utilizing two error standards, mean square error (MSE) and mean absolute percentage error (MAPE). The outcomes showed that the SVGFBM occupies the highest level of accuracy according to smallest values of MSE and MAPE. While the accuracy of GBM come in the tail of the list models under study. These results have affirmed the positive affection of combining memory and stochastic volatility assumption into the GBM model, which agreed findings of numerous earlier works. Furthermore, the findings showed the GFBM models are more accurate than GBM models regardless of the type of volatility. While, under the same type of memory, the models with stochastic volatility assumption are more accurate than the corresponding models of constant volatility assumption. In general, all models considered in this work uncovered high accuracy through the value of MAPE ≤ 10%. This indicates of the ability of applying these models in a real financial environment. Through this empirical study, we can say that the Energy Sector in Saudi Arabia is predictable and stable and afterward we urge financial investors and stockholder to trade and invest in this sector.

This study employs molecular docking techniques to investigate a spectrum of targets within Escherichia coli (E. coli), with a specific focus on four key proteins: Beta-lactamase, MccE protein, Penicillin G acylase, and DNA polymerase II. The research explores the binding interactions of various natural compounds, emphasizing Hypericin. Through computational analyses, the study aims to unveil the potential interactions between these compounds and essential proteins in E. coli. Notably, Hypericin demonstrates remarkable binding energy scores of approximately -10.5 kcal/mol within the Ligand Binding Site of the specified proteins. This observation suggests Hypericin's potential as a potent modulator of E. coli targets, prompting further investigation into its antimicrobial properties and therapeutic applications.

The assessment of Histone deacetylases in conjunction with Curcumin, conducted through the Mcule Database employing the Autodock Vina algorithm, involves an examination of molecular interactions. This analysis includes the calculation of binding energies, revealing the strength and stability of the interactions between Curcumin and various Histone deacetylase targets. The comparison encompasses diverse aspects such as binding energies, specific binding sites, interactions across different targets, structural details, and potential implications for biological activity. The results imply that Curcumin shows heightened affinity for Histone deacetylase 4 in comparison to other investigated histone deacetylases.

To study the strengthening effect on recycled concrete columns by carbon fiber composite materials (CFRP) under different levels of seismic damage, four column specimens were designed for pseudo-static tests. The four specimens were respectively non-destructive without strengthening (prototype), non-destructive strengthening, medium seismic damage strengthening and severe seismic damage strengthening, according to the replacement rate of recycled aggregates and the level of seismic damage. The characteristics of the deformation damage and seismic performance indicators of each specimen were compared and analyzed. A decrease was observed in the initial stiffness of the seismically damaged recycled concrete column specimens strengthened with CFRP, while the ductility, peak bearing capacity and energy dissipation capacity of the specimens were improved. On the other hand, with the reduction of seismic damage and the increase of recycled aggregate replacement rate, the ductility and energy dissipation capacity of the reinforced seismic damaged recycled concrete column specimens were enhanced to different levels. In particular, the cumulative energy consumption of the strengthened specimens under medium seismic damage increased most significantly by 32.5%. In general, the hysteretic curves of the strengthened specimens were full, and the average ductility coefficients were 4.1–6.8. CFRP strengthening was more effective in restoring and enhancing the performance of the recycled concrete column specimens with medium and lower seismic damage levels (displacement ratio ≤ 3%).

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

Sublingual vaccines offer the benefits of inducing mucosal immunity to protect against respiratory viruses, including Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) and influenza, while also enabling needle-free self-administration. Previously, we developed a sublingual vaccine formulated with the SARS-CoV-2 receptor binding domain antigen and Poly(I:C) adjuvant in nonhuman primates, cynomolgus macaques. This study examined the immune and inflammatory responses elicited by the sublingual influenza vaccine containing hemagglutinin (HA) antigen and Poly(I:C) adjuvant and assessed the safety of this vaccine in nonhuman primates. The Poly(I:C)-adjuvanted sublingual vaccine induced both mucosal and systemic immunities. Specifically, the sublingual vaccineproduced HA-specific secretory IgA antibodies in saliva and nasal washings, and HA-specific IgA and IgG were detected in the blood. This vaccine appeared to be safe, as judged from the results of blood tests and plasma C-reactive protein levels. Notably, sublingual vaccination neither increased the production of inflammation-associated cytokines—IFN-alpha, IFN-gamma, and IL-17—in the blood, nor upregulated the gene expression of proinflammatory cytokines—IL12A, IL12B, IFNA1, IFNB1, CD69, and granzyme B—in white blood cells. Moreover, DNA microarray analyses revealed that sublingual vaccination evoked both enhancing and suppressing expression changes in genes associated with immune-related responses in cynomolgus monkeys. Therefore, the sublingual vaccine with Poly(I:C) adjuvant is safe and creates a balanced state of enhancing and suppressing the immune-related response.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

Conventional text style transfer (TST) methodologies primarily utilize style classifiers to segregate the content and stylistic elements of text for effective style transformation. Despite the pivotal role of these classifiers, their influence on TST techniques remains largely unexplored. This study embarks on a detailed exploration of the limitations inherent in style classifiers within current TST frameworks. We reveal that these classifiers often inadequately comprehend sentence syntax, leading to diminished performance in TST models. In response, we introduce the Syntax-Enhanced Style Transfer (SEST) model, a groundbreaking approach incorporating a syntax-sensitive style classifier. This classifier ensures that the extracted style representations robustly encapsulate syntax nuances, enhancing TST effectiveness. Rigorous evaluations across diverse TST benchmarks demonstrate that SEST significantly surpasses contemporary models in performance. Additionally, our case studies highlight SEST's proficiency in producing syntactically coherent sentences that aptly retain original content.

Neisseria gonorrhoeae is a bacterium that causes the sexually transmitted infection gonorrhea. This study employed molecular docking simulations to investigate potential interactions between natural molecules and the Fe(3+) ions import ATP-binding protein fbpC in Neisseria gonorrhoeae FA 1090. Among the screened molecules, Hypericin exhibited a remarkable binding energy of approximately -13.2 kcal/mol, indicating a robust and favorable binding affinity with the target protein. This promising outcome suggests that Hypericin could serve as a potential candidate for further exploration as a therapeutic agent against Neisseria gonorrhoeae infections. However, it is imperative to emphasize that these in silico findings necessitate experimental validation through in vitro and in vivo studies to ascertain the actual efficacy and safety of Hypericin as a treatment option.

The study focused on Molecular Docking simulations using Autodock Vina in conjunction with the Pyrx program to investigate potential drugs and natural compounds against the Bcr-Abl oncoprotein. From initial virtual screening of 200 compounds, 11 potential candidates were selected for further evaluation. Additional investigations included toxicity prediction using the pKCSM server. Among the compounds, Diosmin and Hesperidin showed high maximum tolerated doses in humans and low toxicity. Conversely, only Eltrombopag among the selected drugs exhibited excellent parameters, albeit with a potential risk of liver damage at high dosages. These findings underscore the need for comprehensive evaluation of efficacy and safety in the development of potential treatments targeting the Bcr-Abl oncoprotein.

For the first time, this study identified seven potential ligands with high binding energies through the docking approach against the Crystal Structure of human Melanoma-associated antigen B1 (MAGEB1). The ligands—Imatinib, Bafatinib, Diosmin, Ginkgetin, Bilobetin, Amentoflavone, and Hypericin—showing strong binding energies around -10 kcal/mol, indicate a potentially robust interaction with the target protein. Moreover, the additional step of predicting toxicity properties using the pKCSM server provides valuable insights into the safety profiles of these ligands. From these results, the parameters for Diosmin: —Max. tolerated dose (human),- Oral Rat Acute Toxicity (LD50), and - Oral Rat Chronic Toxicity (LOAEL)—suggest a favorable safety profile, making it a potential candidate for further consideration against Melanoma. Moving forward, it's advisable to conduct further experimental validations, including in vitro and in vivo studies, to confirm the efficacy and safety of Diosmin and other potential ligands. Consideration of pharmacokinetics, metabolism, and specific mechanisms of action will contribute to a comprehensive understanding of these compounds' potential as therapeutic agents.

This study employs molecular docking simulations using Autodock Vina with the Pyrx program to investigate the binding interactions between Human prostate-specific antigen (PSA) and natural compounds, namely Amentoflavone, Ginketin, Rutin, and Hypericin. The evaluation reveals excellent binding energy values, averaging around -10 kcal/mol, suggesting robust and favorable interactions between the selected compounds and PSA. The results provide valuable insights into the potential therapeutic applications of these natural compounds in the context of prostate cancer treatment or management. Further experimental validation is warranted to confirm these findings and explore the viability of these compounds as promising candidates for innovative therapeutic strategies. This research contributes to the growing body of knowledge in the field of molecular docking and its applications in drug discovery and bioinformatics.

My innovative entropy measure, Ismail entropy, namely, (IE) is an ultimate generalization to numerous generalized entropies within the literature. The fractal dimension of IE is identified in this paper. On another applicative note, this paper offers some potential applications of fractal dimension to smart cities. The paper ends with closing remarks combined with some challenging open problems and the next phase of research.

This paper is a brief review of our own work on the Planck quantized version of general relativity theory. It demonstrates several other straightforward methods to simply rewrite the same equations that we have already presented.

Background: While the clinical factors of the post-COVID-19 condition (PCC) are becoming clearer, the economic implications remain uncertain, posing a challenge to healthcare professionals in terms of understanding and managing this emerging phenomenon. This article aims to investigate the demographic and clinical characteristics of PCC patients and quantify the economic impact of their healthcare resource utilisation. Methods: A retrospective and case-control observational study was conducted, comparing the case group of PCC population before and after diagnosis with a control group. Demographic and clinical variables were analysed with the objective of describing the population. Economic analysis was performed to evaluate the resource costs in procedures and primary, secondary (both outpatient and inpatient) and emergency care. Findings: PCC patients (N=341) exhibited older age and elevated cardiovascular risk factors compared to controls (N=49,078). There were differences in the socio-economic distribution between male and female patients in the PCC patients. Hypertension and diabetes mellitus type 2 were the most common chronic diseases observed among the case patients. Economic analysis revealed that PCC patients were approximately four times as costly as control patients, with increased utilisation of healthcare resources. However, post-diagnosis PCC patients showed a reduction in costs, primarily driven by decreased primary care visits and hospitalisations. Conclusion: Coordinated care management for PCC patients is associated with reduced costs and improved healthcare resource utilisation. Further research is warranted to investigate long-term health outcomes and establish causal relationships between COVID-19 sequelae and healthcare resource utilisation.

C-C motif chemokine receptor-8 (CCR8) belongs to class A of G protein-coupled receptors (GPCRs). CCR8 interacts with the specific chemokine ligand CCL1/I-309 in humans, which is produced by various cells, including tumor-associated macrophages and regulatory T cells (Treg). CCR8 is highly expressed on Treg and T-helper 2 (T_H2) cells recruited to the inflammation site and is implicated in allergy, asthma, and cancer progression. The CCR8⁺Treg has been suggested to be an important regulator in the immunosuppressive tumor microenvironment (TME); therefore, it has been desired to develop sensitive monoclonal antibodies (mAbs) for CCR8. This study developed a specific mAb for human CCR8 (hCCR8), which is useful for flow cytometry by employing the Cell-Based Immunization and Screening (CBIS) method. The established anti-hCCR8 mAb, C₈Mab-21, (mouse IgM, kappa) reacted with hCCR8-overexpressed Chinese hamster ovary-K1 (CHO/hCCR8) cells, TALL-1 (acute T lymphoblastic leukemia), CCRF-HSB2 (human T-lymphoblastic leukemia), and natural killer cells, which express endogenous hCCR8 by flow cytometry. Furthermore, C₈Mab-21 demonstrated a moderate binding affinity for CHO/hCCR8 and TALL-1 with a dissociation constant of 6.5×10^-8 M and 2.0×10^-8 M, respectively. C₈Mab-21, which was established by the CBIS method, could be a useful tool for analyzing the hCCR8-related biological response using flow cytometry.

Studies have established the crucial role of sleep among the students which plays a significant role in their mood. This study aimed to examine the mood disorders and sleep quality among undergraduate students at the University of Georgia (UG) and comparison between students’ nationality.This cross-sectional study was a self-reported questionnaire comprised of demographics including age, gender, year of study, current location, lifestyle data (Exercise and smoking), the Depression, Anxiety, and Stress Scale (DAS21) and the Pittsburgh Sleep Quality Index (PSQI). We performed a descriptive analysis, and the Chi-square was statistically significant at p<0.05. The prevalence was at a 95% confidence interval (95% CI) as multivariate analysis examined the multicollinearity. The female students were most of the respondents, below the age of 20 years. The student's mean age was 20.20 (SD± 3.0). DAS report presented 72.7% of students with depressive symptoms, 77.8% with anxiety symptoms, and 62.2% had stress. Georgian students were more at risk of having depressive complaints (95% Cl[1.567-3.788]), anxiety (95% Cl[1.612-4.285]), and stress symptoms (95% Cl[1.743-3.831]). There was a strong relationship between the students who experienced poor sleeping patterns and depressive complaints (aOR 0.10). The students who were smokers (aOR 0.39) were more likely to report anxiety symptoms than the students that do not exercise (aOR 1.68). It was observed that students with depressive symptoms, anxiety, and complaints of stress had a significantly high risk of poor sleep quality. Further studies are recommended to curb psychological symptoms of mood changes in association with sleep disorders among students.

Therapies targeting amyloid, such as monoclonal antibodies like Lecanemab, Aducanumab, and Donanemab, have garnered FDA approval but remain controversial due to limited clinical benefits and significant side effects against Alzheimer. The present theorical work utilized Virtual Screening and Docking techniques to explore potential small natural molecules' interactions with the KIBRA protein, a promising target for drug development. Kibra protein is considered a biomarker for synaptic dysfunction and cognitive decline. Employing Autodock Vina and Pyrx software, on several natural compounds and found Hypericin to exhibit the lowest binding energy of approximately -9 kcal/mol. Previous studies have highlighted Hypericin's strong affinity for Alzheimer's Disease-associated targets like ABAD and BACE1. These findings suggest Hypericin could be as a potential therapeutic agent for Alzheimer's Disease. Further research is warranted to validate its efficacy and safety for clinical use.

Security in the Internet of Things (IoT) is a critical concern due to the growing number of connected devices and the limited resources to implement robust security mechanisms in most of them. Adopting standard assessment frameworks, such as CVSS (Common Vulnerability Score System), allows for systematic vulnerability assessment. At the same time, CVE (Common Vulnerabilities and Exposures) records provide unique identifiers for known security issues, making it easier to share information. However, comparing security solutions is still challenging due to the diverse nature of IoT devices and the ever-evolving threat landscape, requiring continual innovation and collaboration between stakeholders. Furthermore, there still needs to be a simple way to compare technologies and solutions, taking into account the security provided by them. In this sense, in this article, we propose a tool for calculating a security score based on the CVSS index of each existing vulnerability in a given technology. We explain how the tool performs the calculation, discuss some challenges, and propose improvements for future work.

Coastal resources in Lian, Batangas, have undergone significant degradation due to a combination of human activities and natural factors, including sea-level rise, changes in sea-surface temperature, fluctuations in rainfall, increased storm frequency, and sedimentation. This has led to adverse effects on key ecosystems such as corals, mangroves, and seagrasses. To assess the extent of climate change hazards on these coastal resources, a Vulnerability Assessment was conducted in the municipality of Lian, Batangas. The assessment employed a combination of the Coastal Integrity Vulnerability Assessment Toolkit (CIVAT) and Integrated Coastal Sensitivity, Exposure, and Adaptive Capacity to Climate Change (ICSEA-C) guidelines. Additionally, the analysis incorporated detailed mapping using Light Detection and Ranging (LiDAR) data for mangroves and LandSat 8 imagery for corals and seagrasses. The findings at the municipal scale revealed that a staggering 90% of mangroves in Lian, Batangas, were highly vulnerable. This vulnerability was attributed to a high score in intrinsic characteristics and a low adaptive capacity. Similarly, a majority of seagrasses in the area were classified as medium and highly vulnerable at the municipal level. Only 10–20% of seagrasses received low to medium vulnerability scores. Shockingly, almost 100% of the coral reefs in Lian, Batangas, were deemed highly vulnerable, indicating a critical threat to this crucial marine ecosystem.

Microplastics are widespread in freshwater environments and could impact these ecosystems. Bivalves are freshwater organisms that are particularly exposed to microplastic contamination. Therefore, in this preliminary study, the accumulation of microplastics, plasticizers, and additives in the freshwater bivalves Anodonta cygnea through active biomonitoring was investigated. Specimens commercially bought were exposed in three rivers in Central Italy for different exposure times: short (1 month) and long (3 months). The gills and the gastrointestinal tract (GIT) were analyzed separately to evaluate the possible uptake and ingestion of particles via Micro-FTIR. For the first time, small microplastics (SMPs, 5-100 µm), plasticizers, additives, and other micro-litter components, e.g., natural and non-plastic synthetic fibers (APFs) were identified in the bivalve A. cygnea. The most abundant polymer in the gills (94.4%), and GITs (66.1%) was polyamide, which had the highest concentration in each river. A decrease in SMPs' abundance was observed over time in the gills in each river, while the abundance in GIT increased. Compared to polymers, a greater variety of APFs was observed in rivers. The APFs changed during the time of exposure and between different rivers more evidently than polymers, allowing a clearer identification of the possible sources. These results highlighted plastic pollution by SMPs using freshwater bivalves as sentinel organisms and the need to investigate further the additives that can be proxies of the presence of microplastics in the environment and biota.

In this work, nylon 6/ P(N-phenylmaleimide-alt-styrene) blends were prepared by melt blending, and the mechanical, heat-resistant, crystallographic and dynamical mechanical properties of nylon 6/ P(N-phenylmaleimide-alt-styrene) blends with different contents were investigated and analyzed. The results showed that the mechanical properties decreased with increasing PNS, while the heat deflection temperature (HDT), relative crystallinity (Xn), and storage modulus (G’) increased with increasing PNS. The results of differential Scanning Calorimetry (DSC) proved the PNS played the positive role of nucleating PA6. And the results of dynamic mechanical analysis (DMA) proved the PNS could improve the rigidity of PA6/PNS blends. From the SEM, these PNS domains were between 0.2 and 4 μm in diameter. The experimental results indicated that the addition of PNS improved the rigidity of PA6/PNS blends, and then improved the heat-resistant property.

This study provides a comprehensive comparison of the Peter Chew Sum method and Newton's Sum in Quadratic Root Function Computations. Both methods offer significant advancements by alleviating the need for memorization of multiple formulas. However, when confronted with higher-order quadratic root functions such as the calculation of power 33. Newton's Sum method proves cumbersome due to its requirement of all previous answers for final computation, leading to increased steps and error risks. In contrast, the Peter Chew Sum method simplifies the computational process by requiring only a few previous answers, resulting in a more straightforward series of operations. We contextualize our analysis within the historical progression of mathematical techniques, highlighting the transformative leap represented by the Peter Chew Sum method in quadratic root function computations. Peter Chew Sum addressing the limitations of Newton's Sum , especially concerning higher-order functions such as the calculation of power 256. Furthermore, study demonstrates that the innovative approach of the Peter Chew Sum method not only simplifies complex computations but also fosters enhanced conceptual understanding among students. In conclusion, study findings underscore the profound impact of the Peter Chew Sum method on quadratic root function computations.

BACE1 is involved in the production of beta-amyloid peptides, and inhibiting its activity is a potential therapeutic strategy for managing Alzheimer's disease, as excessive beta-amyloid accumulation is a characteristic feature of the disease.Computational results suggest that hypericin has the potential to act as an inhibitor of BACE1. The Molecular Docking results indicate a high binding affinity between hypericin and BACE1, with a notable binding energy score of -10.3 kcal/mol. Additionally, the formation of various chemical bonds, including hydrogen bonds and hydrophobic bonds, further supports the idea that hypericin may effectively interact with the active site of BACE1. It's important to note that while the in silico Molecular Docking results are promising, further in vitro and in vivo studies would be necessary to validate and better understand the inhibitory potential of hypericin against BACE1. Additionally, the practical application of hypericin as a BACE1 inhibitor in a therapeutic context would require careful consideration of factors such as bioavailability, safety, and efficacy.

Docking results suggest that Amentoflavone has a higher affinity for investigated Serine/threonine-protein kinases, indicating potential interactions that may influence the activities of these kinases. The negative values of the binding energies signify strong and stable interactions, suggesting that Amentoflavone could be a key molecule in modulating the functions of these kinases, which play crucial roles in cellular processes such as cell cycle regulation and apoptosis.

Pathogens such as bacteria, fungi and viruses are important components of soil and aquatic communities, where they can benefit from decaying and living organic matter, and may opportunistically infect human and animal hosts. One-third of human infectious diseases is constituted by sapronotic disease agents that are natural inhabitants of soil or aquatic ecosystems. They are capable of existing and reproducing in the environment outside of the host for extended periods of time. However, as ecological research on sapronosis is infrequent and epidemiological models are even rarer, very little information is currently available. Their importance is overlooked in medical and veterinary research, as well as the relationships between free environmental forms and those that are pathogenic. Here, using dynamical models in realistic aquatic metacommunity systems, we analyze sapronosis transmission, using the human pathogen Mycobacterium ulcerans that is responsible for Buruli ulcer. Our work constitutes the first set of metacommunity models of sapronotic disease transmission, and is highly flexible for adaptation to other types of sapronosis. The importance of sapronotic agents on animal and human disease burden needs better understanding and new models of sapronosis disease ecology to guide the management and prevention of this important group of pathogens.

Scholars and policymakers see sustainability as depending on the interrelationships between the three pillars of the environment, society and the economy. However, it remains less clear how key stakeholders with a responsibility for educating the next generation perceive the concept of sustainability and act accordingly. In order to gain new insights, this research scrutinises participant perceptions on sustainability and climate change in two eco-schools in England for primary children (aged 5-11 years). Our case study involved individual interviews with classroom teachers and headteachers, group interviews with fourth- and fifth-year students (ages 10-12 years), and in-class observations. We also analysed data from student exercise books and photographs of school grounds to understand participants’ self-reported knowledge and perceptions of sustainability and climate change. Within a framework drawing on theories of science communication and transformative learning (a learning approach based on having challenging experiences), the results show that the integration of sustainability into the curriculum was limited and problematic. That is despite the fact that all students and teachers were aware of the environmental dimensions of sustainability, like climate change and the overuse of natural sources. These findings suggest that schools are no different to other institutional settings when it comes to dealing with the challenges of integrating sustainability into daily practice. We conclude that there is a need for in-service teacher education programmes to enable and motivate teachers to provide richer teaching-learning environments so as to enable effective learning in schools about sustainability and climate change.

Despite the recent availability of immune checkpoint inhibitors, not all patients affected by Non-Small Cell Lung Cancer (NSCLC) benefit from immunotherapy. The reason for this variability relies to a variety of factors which may allow the identification of novel biomarkers. Presently, a variety of biomarkers are under investigation, including the PD1/PDL1 axis, the tumor mutational burden, and the Microbiota. This latter is made by all bacteria and other microorganisms hosted in our body. The gut microbiota is the most represented and has been involved in different physiological and pathological events, including cancer. In this light, it appears that all conditions modifying gut microbiota can influence cancer, its treatment, and its treatment-related toxicities. The aim of this review is to analyze all conditions influencing the gut microbiota and, therefore, affecting response to immunotherapy, iRAEs and their management in NSCLC patients. The investigation of the landscape of these biological events can allow novel insights for optimal management of NSCLC immunotherapy.

Background: Atopic dermatitis (AD), a common dermatological condition, is often associated with significant economic and social burdens. Despite extensive studies globally, there is a gap in understanding the comprehensive impact of this condition in Romania. Objectives:This study evaluated the economic burden and quality of life impact of AD in Romania, considering both direct and indirect costs. Materials & Methods: A mixed methods cost of illness study was conducted from April to October 2023. A patient survey, expert reviews, and national health data analysis were used to assess direct medical costs (treatments, medical services), direct non-medical costs (transportation, accommodation), and indirect costs (productivity losses). Quality of life was evaluated using the EuroQol EQ-5D-5L instrument. Results: In 2022, the total cost of atopic dermatitis in Romania was 32.983.498 EUR for adults and 31.573.968 EUR for children. Adult costs included 24.534.603 EUR in direct and 8.429.884 EUR in indirect medical costs, with an average annual cost per patient of 447 EUR. Pediatric costs involved 15.026.781 EUR in direct and 16.516.410 EUR in indirect costs, averaging 290 EUR per patient annually. Conclusion: Care expenditure with AD management in Romania is substantially lower than in other countries, posing a significant economic burden, primarily driven by indirect costs. This study provides a foundation for future policy interventions and highlights the need for targeted management strategies for AD.

Background : Probiotics are composed of microorganisms that have positive effects on health when consumed in prescribed quantities. Lately, studies have attempted to establish this role of probiotics in enhancing health. Aim : The aim of this study was to compare the antifungal activity of 3 different probiotics against Candida albicans.Methodology :This was an in-vitro study. 3 types of commercially available probiotics - Bifilac, Pre pro HS and VSL-3 were cultured separately with Candida albicans and were placed under incubation. The maximum zone of inhibition was recorded for each of the probiotic solutions.Results : In this study, it was found that among the three probiotic products, Bifilac exhibited a maximum zone of inhibition of 13mm at concentration of 100µL against C. albicans, while Pre pro HS and VSL-3 showed zone of inhibition of 11mm at concentrations of 50µL and 100µL, respectively.Conclusion : Within the limits of the present study, This study could prove that probiotics can be considered as an alternative and safe treatment option for treatment of Oral candidiasis infections.

In order to search possible residual minor phases in Y-Ba-Cu-O family, powdered mixtures of Y₂O₃ + BaCO₃ + CuO and, independently, superconducting compound YBa₂Cu₃O_7-x have been treated in evacuated cells and elevated temperatures.YBa₂Cu₃O_7-x was reduced to YBa₂Cu₃O₅ by use of the special home designed Taconis-Knudsen vacuum device. A subsequent doping by oxygen converts produced insulator YBa₂Cu₃O₅ to semiconductor or metal YBa₂Cu₃O_5+x (0<x<0.3). In addition to YBa₂Cu₃O₅, 0.05 volume percent of the minor delafossite phase Y₂Cu₂O₄ was being spotted in the powder mixture 1/2 Y₂O₃ + 2BaCO₃+6Cu₂O, heated up to 818 °C in an inert gas atmosphere. An attempt to prepare the insulating bulk delafossite samples was successful, and subsequent doping by oxygen produces novel metallic phases.

A cell-surface ectonucleotidase CD39 mediates the conversion of extracellular ATP into immunosuppressive adenosine with another ectonucleotidase CD73. The elevated adenosine in the tumor microenvironment (TME) attenuates antitumor immunity, which promotes tumor cell immunologic escape and progression. Anti-CD39 monoclonal antibodies (mAbs), which suppress the enzymatic activity, can be applied to antitumor therapy. Therefore, an understanding of the relationship between the inhibitory activity and epitope of mAbs is important. We previously established an anti-mouse CD39 (mCD39) mAb, C₃₉Mab-1 using the Cell-Based Immunization and Screening (CBIS) method. In this study, we determined the critical epitope of C₃₉Mab-1 using flow cytometry. We performed the PA tag (12 amino acids)-substituted analysis (named PA scanning) and RIEDL tag (5 amino acids)-substituted analysis (named RIEDL scanning) to determine the critical epitope of C₃₉Mab-1 using flow cytometry. By the combination of PA scanning and RIEDL scanning, we identified the conformational epitope, spanning three segments of 275^th to 279^th, 282^nd to 291^st, and 306^th to 323^rd amino acids of mCD39. These analyses would contribute to the identification of the conformational epitope of membrane proteins.

Molecular docking, a computational method predicting how molecules bind to target proteins, is employed in this study to explore Polydatin's interactions with Ras-related protein Rab (Rab) proteins using the Mcule Database. This database validates the docking results and offers insights into the pharmacological properties of Polydatin. Notably, specific Rab proteins like Rab-5A, HRas, and Rab-18 exhibit robust interactions with Polydatin, indicated by favorable binding energies.These findings illuminate the potential roles of Polydatin in therapeutic and biological contexts, emphasizing its interaction with Rab proteins. The Mcule Database enhances the credibility of the study, providing additional perspectives on Polydatin's applications. The observed interactions, particularly with key proteins like HRas, present a promising avenue for modulating cellular signaling pathways. This modulation holds therapeutic potential, potentially addressing conditions associated with pathway overactivity, including specific cancer types.

Multilingual classrooms are becoming more common worldwide due to increasing mobility. Teaching foreign languages using the mother tongue in multilingual classrooms has become problematic; some of the significant concerns in Japanese language acquisition – such as the high contextuality of the language, vocabulary and kanji learning – make the direct teaching method confusing for many students, especially at the beginner and elementary levels. This article provides the preliminary results of a study carried out as a component of a more extensive empirical research project on instructional languages in classrooms teaching Japanese as a foreign language. It aims to gather, analyse and synthesise data from a survey conducted at a supranational level. The results of the first two sections of a questionnaire containing closed and open-ended questions were used for a quantitative analysis of the profile of Japanese language instructors with a focus on finding possible connections. The wide geographic distribution of the respondents (274 teachers from fifty-seven countries and regions) made it possible to collect data from a more representative sample and draw meaningful conclusions about the spread of multilingual classrooms that would be impossible in smaller-scale research. The study’s primary results show the proportion of multilingual classrooms among countries in different regions and across different educational stages, the distribution of Japanese language instructors in various educational stages depending on the highest level of formal education attained, and the proportion of part-time instructors working in different academic institutions.

We demonstrate how a rigorous mathematical approach can be used to extract a current CMB temperature of 2.7276 ±0.0723 K from the 580 type Ia supernova data points in the Union2 database. Using redshift formula: z = Sqrt(Rh/R_t) − 1, incorporated into our new CMB redshift prediction redshift formula, we find that the above current CMB temperature value is a remarkably good match for this particular data set. In addition, we can alternatively start out with the measured current CMB temperature and extract the Hubble constant from all 580 supernovae. We then get an estimated Hubble constant of H0 = 66.8711+0.0019 km/s/Mpc when using the CMB temperature from the recent Dhal et al study [1] in combination with redshifts from all 580 supernovae. Furthermore, we get an estimated Hubble constant value of H_0 = 66.8943+0.0287 km/s/Mpc when using the CMB temperature measured by Fixsen [2]. In summary, our simple model essentially perfectly matches all 580 type Ia supernova redshifts while extracting H_0 or T_0 values. The Hubble constant we extract by this method fits very well with the Hubble constant extracted from the CMB by other studies. We believe that our new approach likely solves the Hubble tension problem, at least inside R_h = ct cosmology.

The Jakarta LARP community, established in March 2020 and primarily active in Gelora Bung Karno, fosters inclusivity, diversity, and physical role-playing activities. It adheres to a policy of excluding ultra-nationalist ideologies and integrates new members despite language barriers. Bruhn (2011) defines this kind of community sharing the same goals, values, and lifestyles, while McMillan & Chavis (1986) outline four aspects of the sense of community.The research discovered that communities endure by utilizing solidarity built on the basis of their peculiarities. This study employed ethnographic methods alongside grounded research to identify the community's culture and their efforts to sustain and utilize it as community solidarity.

The C-C motif chemokine receptor 8 (CCR8) is highly and selectively expressed in regulatory T (Treg) cells and is associated with tumor progression. The massive accumulation of Treg cells into tumors suppresses the effector function of CD8⁺ cells against tumor cells. Therefore, selective depletion of Treg cells using anti-CCR8 monoclonal antibodies (mAbs) reinvigorates antitumor immune responses and improves responses to cancer immunotherapy. Previously, we developed an anti-mouse CCR8 (mCCR8) mAb, C₈Mab-2, using the Cell-Based Immunization and Screening (CBIS) method. In this study, the binding epitope of C₈Mab-2 was investigated using flow cytometry. The mCCR8 extracellular domain-substituted mutant analysis showed that C₈Mab-2 recognizes the N-terminal region (1–33 amino acids) of mCCR8. Next, 1×alanine (or glycine) scanning and 2×alanine (or glycine) scanning were conducted in the N-terminal region. The results revealed that the _17-DFFTAP_-22 sequence is important for the recognition by C₈Mab-2, and Thr20 is a central amino acid of the epitope. These results revealed the involvement of the N-terminus of mCCR8 in the recognition by C₈Mab-2.

AbstractBackground: Empowering Communities, Combating HIV/AIDS: The Indispensable Role of Community-Based Strategies in Awareness and PreventionObjective: Highlight the significance of community-based approaches in addressing the ongoing HIV/AIDS pandemic through enhanced awareness, reduced stigma, and effective prevention measures.Method: This article provides a theoretical analysis of community-based HIV/AIDS interventions, drawing upon key strategies and successful examples from diverse settings.Results: Community-based initiatives emerge as critical factors in empowering individuals and communities to take ownership of their health. Through culturally-sensitive education, accessible testing, and comprehensive support services, these initiatives effectively diminish the social stigma surrounding HIV/AIDS and promote preventative behaviors. Examples of successful programs illustrate the potential of community-driven approaches to achieve measurable reductions in transmission rates and improved health outcomes.Conclusion: The fight against HIV/AIDS necessitates robust community engagement. Community-based interventions, grounded in local knowledge and addressing specific needs, offer a promising pathway towards fostering health equity, reducing stigma, and ultimately curtailing the spread of the virus. Further research and investment in these initiatives are crucial to ensuring their scalability and sustained impact on global HIV/AIDS prevention efforts.

In the wake of increasing digital fraud, this paper introduces an innovative application of Artificial Intelligence (AI) in detecting fraudulent activities across finance, healthcare, and e-commerce sectors. It presents a detailed analysis of machine learning methodologies, specifically focusing on the advantages of supervised, unsupervised, and deep learning techniques. The paper addresses the challenges such as data imbalance, model interpretability, and ethical implications in AI-based fraud detection. It also discusses the necessity of high-quality datasets and advocates for the integration of traditional and advanced machine learning methods to enhance accuracy and adaptability in fraud identification. However, it acknowledges the limitations including computational demands and overfitting risks. The study underscores the importance of collaborative efforts between AI experts and industry professionals to develop ethical, efficient, and reliable AI solutions for fraud detection.