The surface planarity and asperity removal behaviors of atomic scale under the ultrathin water environment was studied for the nanoscale process by molecular dynamics simulation. The monolayer atomic removal was achieved under the noncontact and monoatomic layer contact conditions with different water film thickness, and the newly formed surface is relatively smooth and no deformed layer and plastic defects exist. The nanoscale processing is governed by the interatomic adhering action during which the water film transmits the loading forces to Cu surface and thereby result in the migration and removal of surface atoms. With scratching depth ≥ 0.5 nm, the abrasive particle squeezed out the water film from scratching region and scratched Cu surface directly, leading to the surface quality deterioration mainly governed by the plowing action. This study brings the goals of “0 nm planarity, 0 residual defects and 0 polishing pressure” closer to us in the nanoscale process for the development of ultra-precision manufacture technology.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

Giant unilamellar vesicles (GUVs) are membrane model used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol dry lipid film is formed. Drying of the lipid film induce Cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals, where these crystals does not participate in formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose novel electroformation protocol that includes rapid solvent exchange, plasma cleaning and spin-coating methods to produce GUVs. We tested the protocol focusing on vesicles with high Chol content using different spin-coating durations and vesicle types deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles made out of phosphatidylcholine/Chol mixture was 30 s. Mulitlamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores were deposited on electrode for 1.5/1 Chol/phosphatidylcholine lipid mixture and the results were compared. Electroformation using all three deposited vesicle types gave a high GUVs yield, but deposition of LUVs obtained by extrusion of MLVs through 100 nm membrane pores gave the most reproducible results. Using deposition of these LUVs, we produced GUVs with high yield for 6 different Chol concentrations (from 0 % to 71.4%). Using protocol that includes dry lipid film GUVs yield was lower and Chol demixing artifact was induced, proving that the lipid film should never undergo drying when Chol content is high.

A new biodegradable paper-based film is a hot research topic in the development of green agriculture. In this paper, a black paper base film coated with cooked tung oil with excellent mechanical properties, hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high pigment carbon black solution on the surface of base paper. The results showed that the surface solidified oil film with rough structure was made by the brush coating process of cooked tung oil, and the base film of black paper was given hydrophobic structure, and the contact angle reached 98.9 °. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black makes the black paper base film have heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of the cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil.

Flexible electrochemical sensors can adhere to any bendable surface with conformal contact, enabling continuous data monitoring without compromising the surface's dynamics. Among various materials that have been explored for flexible electronics, metal-organic frameworks (MOFs) exhibit dynamic responses to physical and chemical signals, offering new opportunities for flexible electrochemical sensing technologies. This review aims to explore the role of electrocatalysis in MOF films specifically designed for flexible electrochemical sensing applications, with a focus on their design, fabrication techniques, and applications. We systematically categorize the design and fabrication techniques used in preparing MOF films, including in-situ growth, layer-by-layer assembly, and polymer-assisted strategies. The implications of MOF-based flexible electrochemical sensors are examined in the context of wearable devices, environmental monitoring, and healthcare diagnostics. Future research is anticipated to shift from traditional microcrystalline powder synthesis to MOF thin-film deposition, which is expected to not only enhance the performance of MOFs in flexible electronics but also improve sensing efficiency and reliability, paving the way for more robust and versatile sensor technologies.

The influence of the film thickness and the substrate’s refractive index on the surface mode at the superstrate is an important study step that may help clearing some of the misunderstandings surrounding their propagation mechanism. A single sub-wavelength slit perforating a thin metallic film is among the simplest nanostructure capable of launching Surface Plasmon Polaritons on its surrounding surface when excited by an incident field. Here, the impact of the substrate and the film thickness on surface waves is investigated. When the thickness of the film is comparable to its skin depth, SPP waves from the substrate penetrate the film and emerge from the superstrate, creating a superposition of two SPP waves, that leads to a beat interference envelope with well-defined loci which are the function of both the drive frequency and the dielectric constant of the substrate/superstrate. As the film thickness is reduced to the SPP’s penetration depth, surface waves from optically denser dielectric/metal interface would dominate, leading to volume plasmons that propagate inside the film at optical frequencies. Interference of periodic volume charge density with the incident field over the film creates charge bundles that are periodic in space and time.

A Cu₂ZnSnS₄ (CZTS) film with a thickness of approximately 1.5 μm was fabricated on a Mo-coated glass substrate by annealing a CZTS precursor fabricated from nanoparticle ink. The chemical states of the elements in the CZTS thin film in the depth direction were studied to identify the presence of secondary phases, which are detrimental to the performance of solar cells containing CZTS. X-ray diffraction was unable to detect any secondary phases in CZTS because of their small relative amount. Instead, X-ray photoelectron spectroscopy (XPS), which is highly sensitive to chemical state, was conducted at different depths in the CZTS film to further check the presence of secondary phases. XPS analysis revealed peaks shift consistent with the presence of secondary phases. For the CZTS film annealed in a S atmosphere at 575 °C for 3 h, the film surface consisted of a secondary-phase layer composed of CuS, ZnS, and SnSx (x=1 or 2) originating from the decomposition of CZTS. At depths below 80 nm, the film was pure CZTS. Formation of MoS2 at the CZTS–Mo interface was confirmed by XPS analysis of Mo and S.

The Western ‘discovery’ of Japanese cinema in the 1950s prompted scholars to articulate essentialist visions understanding its singularities as a result of its isolation from the rest of the World and its close links to local aesthetic and philosophical traditions. Recent approaches however, have evidenced the limitations of this paradigm of ‘national cinema’. Higson (1989) opened a critical discussion on the existing consumption, text andproduction-based approaches to this concept. This article draws on Higson´s contribution and calls into question traditional theorising of Japanese film as a national cinema. Contradictions are illustrated by assessing the other side of the ‘discovery’ of Japanese cinema: certain gendaigeki works that succeeded at the domestic box office while jidaigeki burst into European film festivals. The Taiyōzoku and subsequent Mukokuseki Action created a new postwar iconography by adapting codes of representation from Hollywood youth and western films. This article does not attempt to deny the uniqueness of this film culture, but rather seeks to highlight the need to reformulate the paradigm of national cinema in the Japanese case, and illustrate the sense in which it was created from outside, failing to recognise its reach transnational intertextuality.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

We investigated layered titanium nitride (TiN) and aluminum nitride (AlN) for color glasses in Building Integrated Photovoltaic (BIPV) systems. AlN and TiN are among suitable and cost-effective optical materials to be used as thin multilayer films, owing to the significant difference in their refractive index. To fabricate the structure, we used radio frequency magnetron deposition method to achieve the target thickness uniformly. A simple, fast, and cheap fabrication method is achieved by depositing the multilayer films in a single sputtering chamber. It is demonstrated that a multilayer stack that allows light to move from a low refractive index layer to a high refractive index layer or vice-versa can effectively create various distinct color reflections for different film thicknesses and multilayer structures. It is investigated from simulation based on wave optics that, TiN/AlN multilayer offers better color design freedom and cheaper fabrication process as compared to AlN/TiN multilayer films. Blue, green, and yellow color glasses with optical transmittance of more than 80% was achieved by ITO coated glass/TiN/AlN multilayer films. This technology exhibits good potential in commercial BIPV system applications.

Abstract: The expansion of global industries results in the release of harmful volatile acid vapors into the environment, posing a threat to various life forms. Hence, it's crucial to prioritize the development of swift sensing systems capable of monitoring these volatile acid vapors. This initiative holds great importance in safeguarding a clean and safe environment. This paper presents the synthesis and characterization of pyrene-based covalent organic frameworks (COFs) demonstrating exceptional crystallinity, thermal stability, and intense fluorescence. Three COFs—PP-COF, PT-COF, and PE-COF—were synthesized, showcasing large surface areas and robust thermal stability up to 400 °C. The fluorescence properties and intramolecular charge transfer within these COFs were significantly influenced by their Schiff base bonding types and π-stacking degrees between COF layers. Notably, PE-COF emerged as the most fluorescent among the three COFs and exhibited exceptional sensitivity and rapid response as a fluorescent chemosensor for detecting HCl in solution. The reversible protonation of imine bonds in these COFs allowed for the creation of highly sensitive acid vapor sensors, showcasing a shift in spectral absorption while maintaining structural integrity. This research highlights the potential of COFs as reliable and reusable sensors for detecting harmful acid vapors, addressing environmental concerns arising from industrial activities.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

Biodegradable and renewable plastic films have been regarded as promising alternative green materials to achieve the substitution polythene (PE)films to reduce plastic pollution. Poly (butylene adipate-co-terephthalate) (PBAT) is a kind of biodegradable polyester, which is widely used in the production of biodegradable mulching films. However, the high cost of PBAT limited it applications. Thus, lignin, one of the most abundant biomass resources was incorporated into PBAT matrix in the present work. A series of Lignin/PBAT biodegradable plastics films with different Lignin/PBAT weight ratios (0.00 %-5.00 %) were successfully fabricated using twin screw and twin roll extruders. The chemical compositions, morphologies, thermal stabilities, mechanical properties, and barrier properties of samples were characterized by XRD, FTIR, TG/DSC, mechanical testing machine, and WVTR, respectively. Results show that the corporation of lignin into PBAT matrix could lead to improved thermal stabilities, mechanical properties and barrier properties of films even after Xenon lamp aging process, especially when Lignin/PBAT weight ratio is 1.00 % in the present work. This work provides a very promising approach for fabrication of biodegradable plastics films with low cost, enhanced mechanical properties and barrier properties, the as-prepared samples may have potential applications in agricultural or food packaging materials.

Film therapy, the therapeutic use of movies in psychological therapies, is a growing area of interest to therapists and researchers. This paper presents the MOVIE model of film therapy, a widely applicable, trauma-informed framework for working with film imagery and themes in individual or group therapy, counsellor education and self-help. Film or cinema therapy is a highly accessible and relatable method for many diverse client and student groups with benefits that include, catharsis and emotional processing, greater ease of dialogue around issues, increased empathy, and interpersonal learning, engaging with new perspectives and learning skills. Following the model clients mindfully observe and voice their emotional and psychological responses to movie watching, identify how the imagery, characters, themes, and narrative symbolise personal experience and consider any new possibilities that emerged through re-authoring personal narratives. The model is informed by a practice focused review of literature.

We demonstrate a concept and fabrication of lithography-free layered metal-\ce{SiO2} thin-film structures which have reduced reflectivity (black appearance), to as low as 0.9~\%, with 4.9~\% broadband reflectance (8.9~\% for soda lime) in the 500 - 1400~nm range. The multi-layered (four layers) thin-film metamaterial is designed so that optical impedance matching produces minimal reflectance and transmittance within the visible and infra-red (IR) spectral region for a range of incident angles. The structure has enhanced absorbance and is easily tuned for reduced minimal transmission and reflection.

The main aim of this work is to report an alternative energy efficient technique of fabricating flexible thermoelectric generators (TEGs) using printable ink. In this process, we have fabricated thermoelectric (TE) composite thick film and we are experimenting several ways to overcome the challenges of conventional and additive manufacturing methods. Two different mesh sizes of n-type bismuth particle, various binder to thermoelectric (TE) material weight ratio, and two different pressure (200 MPa and 300 MPa) were employed for optimizing the thermoelectric properties of TE composite films. We are also exploring naturally occurring chitosan as a binder. Dimethyl sulfoxide (DMSO) dissolved chitosan was used for the binder and less than 0.2 wt% of chitosan was sufficient for the fabrication of TE inks and composite films. Low energy intensive curing process was employed to evaporate the solvent from the drop casted inks. External uniaxial pressure not only eliminated high energy intensive curing processes but also increased the packing density of the film by removing pores and voids in the chitosan-bismuth composite film. The microstructure analysis reveals that bulk-like structure, which rarely has voids, pores and grain boundaries, was observed in the composite films pressed at sufficiently high pressures. The highest performing composite film was obtained with the conditions of 1:2000 binder to bismuth weight ratio, 100 mesh of particle size, and 300 MPa of pressure. The best performing bismuth chitosan composite film pressed at 300 MPa had the power factor as 4009 ± 391 μW/m·K² with high electrical conductivity value of 7337 ± 522 S/cm. The measured thermal conductivity of the best performing chitosan-bismuth composite film was 4.4 ± 0.7 W/m·K and the figure of merit calculated from the thermal conductivity was 0.27 at room temperature.

A comparative study of the photocatalytic decoloration of methylene blue (MB) dissolved in water was conducted, using three semiconductor oxides: zinc oxide (ZnO), tin oxide (SnO2) and titanium dioxide (TiO2) in the form of thin films and varying their thickness ~ 100, 200, and 300 nm for each film. All the films were deposited using the cost-effective dip-coating technique, at moderate temperature processing (400 °C) with sol-gel solutions on cheap glass substrates. The structural, morphological, and compositional properties of the films were analyzed by X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Raman spectroscopy, respectively. The degradation of MB was studied by varying both thickness and type of semiconductor oxides through measurements of optical absorbance of decolorated liquid by photocatalytic process. Structural analysis shows that ZnO and SnO2 films were polycrystalline with preferential growth of (002) and (110) planes respectively, whereas, an amorphous structure was observed for TiO2 films. In addition, morphological properties confirms that the surfaces of all the films are conformed with nano grains in round and irregular shapes. Based on all results reported in this work, that authors believe that the degradation efficiency of MB depends on the thickness of the film and the type of semiconductor material used as a catalyst. The highest degradation efficiencies were recorded with an exposure time of 120 min and with an initial concentration of 10 mg/L for ZnO, SnO2, and TiO2 films were: 100, 88 %, and 76 %, respectively.

Intravaginal drug administration offers several advantages over other administration routes, primarily by bypassing the initial stages of metabolism. Additionally, this route has demonstrated both local and systemic effects. To prevent the disintegration of molecules in the mucous barriers of wet cavities, mucoadhesive polymeric systems can be utilized. In this study, the performance and characteristics of a mucoadhesive film composed of HPMC-PEG 400 containing retinol molecules was determined using various techniques. Scanning Electron Microscopy (SEM) was employed to determine the porous structure of the film. Thermogravimetric Analysis (TGA) was conducted at different temperatures to assess thermal stability. Fourier Transform Infrared Spectroscopy (FTIR) analyzed the functional groups and the intermolecular interactions between the film and the drug. Swelling and weight loss tests indicated that the film disintegrated within 3-4 days. For drug delivery evaluation based on the Higuchi equation, UV-VIS spectroscopy was used. Additionally, the surface wetting properties were assessed through contact angle measurements. The biocompatibility of the system was confirmed using the MTT assay. Finally, adhesion and glide tests demonstrated the film's interaction with porcine uterine tissue. This study shows that the HPMC-PEG 400 film containing retinol molecules interacts effectively with tissue and could be considered a novel tool for treating damaged epithelial tissues.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

Organic electrochemical transistors (OECTs) based on conducting polymers have attracted significant attention in the field of biosensors. PEDOT:PSS and polyaniline (PANI) are representative conducting polymers used for OECTs. While there are many studies on PEDOT:PSS, there are not so many reports on PANI-based OECTs, and a detailed study to compare these two polymers has been desired. In this study, we investigated the fabrication conditions to produce the best performance in the OECTs using the above-mentioned two types of conducting polymers. Two main parameters were film thickness and film surface roughness. For PEDOT:PSS, the optimal conditions for fabricating thin films were a spin-coating rate of 3000 rpm and DI water immersion time of 18 hours. For PANI, the optimal conditions were a spin-coating rate of 3000 rpm and DI water immersion time of 5 seconds, and adding dodecylbenzenesulfonic acid (DBSA) was found to provide better OECT performances. The OECT performances based on PEDOT:PSS were superior to those based on PANI in terms of conductivity and transconductance, but PANI showed excellence in terms of film thickness and surface smoothness, leading to the good reproducibility of OECT performances.

The corrosion resistance of two cast CoCr based alloys, with different amounts of chromium and with different alloying elements in the bulk composition of the alloy, was assessed. Herewith, we investigated the corrosion behavior of Co21Cr8Mo7W and Co29Cr7W by open circuit potential (OCP), potentiodynamic polarization (PP) and electrochemical impedance spectroscopy (EIS) in 0.1 M phosphate buffer solution (PBS) at 37°C for long time immersion. After 1000 hours of immersion, the corrosion current density (icor), estimated from anodic polarization tests, is lower for Co21Cr8Mo7W (i.e. 49 nA cm-2) alloy compared to Co29Cr7W alloy (180 nA cm-2). As regards the corrosion potential (Ecor), a nobler value was observed for Co21Cr8Mo7W (i.e. -59 mV vs. Ag/AgCl) compared to Co29Cr7W (i.e. -114 mV vs. Ag/AgCl). These findings suggest a better corrosion resistance of the film formed on the alloy containing lower amount of Cr and two alloying elements, namely Mo and W. These results are promising ones in terms of medical applications because they open new strategies in obtaining alloys with lower content of chromium and with higher protective properties against corrosion attack.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

In response to the problem of no supporting equipment for the cultivation of Codonopsis in the hilly and mountainous areas of northwest China, a combined machine for transplanting outcrop of Codonopsis with micro ridge covered with film is designed. The key components of the prototype are analyzed and designed, and the structures and working parameters of the seedbed preparation device, seedling casting device, rotary tillage soil-covering device, film covering device, seedling head burial and film edge soil-covering device are determined. The transmission system scheme is established, and the working mechanism of the core components is analyzed. Field experiments show that when the target seedling spacing is 4.4cm and the machines moves forward at the speed of 0.1, 0.15, and 0.2m/s, the variation coefficient of planting spacing and the qualification rate of planting depth all meet the standard requirements. The qualified rate of planting posture and film side outcrop are greatly affected by the operating speed of the machine, and decrease with the increase of operating speed. When the operating speed reaches 0.1m/s, the average variation coefficient of planting spacing is 0.08%, the average qualified rate of planting depth, planting posture and film side outcrop is 95.83%, 94.17% and 93.33% respectively, which shows that the operating performance is better than that of the operating speed of 0.15m/s and 0.2m/s. This study provides new reference for the theoretical research and design of mechanized and automated transplanting machinery for Codonopsis seedlings.

COVID-19 infection, caused by SARS-CoV-2, is inequitably distributed and more lethal among populations with lower socioeconomic status. Direct contact with contaminated surfaces has been one of the virus sources, as it remains infective up to days. Several disinfectants have been shown to inactivate SARS-CoV-2 but they rapidly evaporate, are flammable or toxic and may be scarce or inexistent for the vulnerable populations. Therefore, we are proposing a simple, easy to prepare, low-cost and efficient antiviral films, made with wide available dishwasher detergent, which can be spread in hands and inanimate surfaces and maintains virucidal activity for longer periods than the current sanitizers. Avian coronavirus (ACoV) was used as model of challenge to test the antivirus efficacy of proposed films. Polystyrene microplates were covered with a thin layer of detergent formula. After drying, the films were exposed to different virus doses for 10 minutes and virus infectivity were determined using embryonated chicken eggs and RNA virus quantification in allantoic fluids by RT-qPCR. The films showed to inactive the ACoV (ranging from 103.66 to 106.66 EID50), which is chemically and morphologically similar to SARSCoV-2 and may constitute an excellent alternative to minimize the spread of Covid-19.

Subwavelength hole array (HA) metasurfaces support the so-called extraordinary optical transmission (EOT) resonance that has already been exploited for sensing. In this work, we demonstrate the superior performance of a different resonant regime of HA metasurfaces called anomalous EOT, by doing a thorough numerical and experimental study of its ability as a thin-film label-free sensor in the terahertz (THz) band. A comprehensive analysis using both the regular and anomalous EOT resonances is done by depositing thin layers of a dielectric analyte of different thicknesses on the structures in different scenarios. We carry out a detailed comparison and demonstrate that the best sensing performance is achieved when the structure operates in the anomalous EOT resonance and the analyte is deposited on the non-patterned side, improving by a factor between 2 and 3 the results of the EOT resonance in any of the considered scenarios. This can be explained by the comparatively narrower linewidth of the anomalous EOT resonance. The results presented expand the reach of subwavelength hole arrays for sensing applications by considering the anomalous EOT regime that is usually overlooked in the literature.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

This research presents a novel approach to film analysis, leveraging word vectors to objectively evaluate movie critiques. Focusing on Director Chanwook Park’s award-winning film, ’Decision to Leave’, the study employs word vectors derived from the movie’s script of Korean text. Traditional critiques often emphasize contrasting elements and themes, but their subjective nature poses challenges in objective validation. To address this, we trained a language model using LSTM on the film’s script, obtaining word vectors that capture the essence of the narrative. These vectors were then used to perform various text analyses, including similarity and analogy operation for the keywords suggested by the critiques. By comparing the semantic relationships in the critiques with those derived from the word vectors, we could objectively validate the critiques’ assertions. Furthermore, we visualized the word vectors in a two-dimensional space, confirming the spatial relationships of key terms highlighted in critiques. The study underscores the potential of word vectors in providing a more objective lens for film analysis, bridging the gap between traditional film criticism and data-driven insights.

The objective of this work is to identify the mechanism of dropwise condensation on a smooth solid surface. We investigate the stable dropwise condensation that occurs at a droplet growth rate of 1 µm/s in diameter on a gold-coated glass surface. Additionally, we present our observations on unstable dropwise condensation, i.e., degradation of dropwise condensation of steam on a gold surface. The Surface Plasmon Resonance Imaging (SPRi) approach used in this study has lateral resolutions of 4-10 µm, thickness resolutions of 0.1-1 nm, and temporal resolutions of 200-10,000 frames per second (FPS). SPRi is used to evaluate the existence and structure of thin films and occurrence of initial nuclei during condensation. Visualization of the onset of stable dropwise condensation suggests droplets form at heterogeneous nucleation sites and that no film greater than a monolayer exists on the surface before the formation of droplets. Observation of the unstable dropwise condensation of steam shows the existence of water films that are several nanometers thick between droplets. This work shows that neither the nucleation theory or film rupture theory can individually explain the physics of dropwise condensation. Therefore, there is a need for a more comprehensive theory that can explain the mechanism of dropwise condensation.

This paper addresses the capability to alter the hydrophilic wettability characteristics of poly(vinyl alcohol) (PVA) polymer films doped with glycerol. Films of PVA and glycerol-choline chloride (GCC) blends have been prepared using the solution casting method with different glycerol dopants ranging from 0% to 10% (wt %). The results show that as the GCC dopant content increases from 0% to 10%, the wettability increases, thus increasing the surface energy of the solid film. The wettability changes are observed by identifying the contact angle of 10 µL deionized water droplet which altered from 55^o to 28^o as dopant content changed from 0% to 10% per PVA solution weight. The results show that the roughness of film surfaces increases as the content of dopant (GCC) increases in the film indicating that roughness has a strong influence on the wettability of the casted films.

Changing the film thickness to manipulate the microstructural properties has been considered as a potential method in practical application. Here, we report that atomic-scale structural properties regulated by film thickness in NiCO2O4(NCO)/CuFe2O4(CFO) bilayer heterostructure prepared on (001)-MgAl2O4 (MAO) substrate by means of aberration-corrected scanning transmission electron microscopy (STEM). The misfit dislocations at NCO/CFO interface and antiphase boundaries (APBs) bound to dislocations within the films both are found in NCO (40 nm)/CFO (40 nm)/MAO heterostructure to contribute to relaxation of mismatch lattice strain. In addition, the non-overlapping a/4[101]-APB is found and the structural transformation of this kind of APB is resolved at atomic scale. In contrast, only the interfacial dislocations form at interface without the formation of APBs within the films in NCO (10 nm)/CFO (40 nm)/MAO heterostructure. Our results provide evidence that formation of microstructural defects can be regulated by changing film thickness to tune magnetic properties of epitaxial bilayer spinel oxide films.

Liposome vesicle is an ideal carrier for carbon nanotube (CNT) to serve as the water channel that allows the fast transport of water molecules, and thus enhancing the membrane permeability. However, low quantity of the inserted CNT in the liposome vesicle is an important factor that limited further improvement of the membrane flux. In present study, positively charged lipids (2,3-dioleoyloxy-propyl)-trimethylammonium-chloride (DOTAP) was introduced to the 1,2-dioleoyl-sn-glycero-3-phosphoethanolamineon (DOPE) liposome vesicles to tailor the vesicle charge, so as to evaluate the effect of positively charged DOTAP on the insertion of CNT into liposomes and separation performance of thin-film nanocomposite (TFN) membranes. The results showed that addition of DOTAP induced more quantity of CNT inserted into the liposome vesicles, since the shrinkage rate (k) and permeability (Pf) of liposome vesicles present obvious increase with increased content of DOTAP in the liposome vesicles. Besides, it contributed to 252.3% higher water flux for TFN membranes containing DOPE/DOTAP2:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 2:1) than TFC membranes. More important, it presented 106.7% higher water flux for TFN membranes containing DOPE/DOTAP4:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 4:1), which was originated from the more water channels that the CNT provided in the liposome vesicles. In all, positively charged DOTAP effectively tailored the vesicle charge, which provided a better carrier for the insertion of more quantity of CNT, and contributed to higher permeability of TFN membranes.

The cornea is an avascular tissue which has attracted much attention by the uniqueness of its anatomical characteristics, it has, in proportion, an enormous size, in relation to the number of vessels, because on average few cells in the organism are away more than 30 microns of a blood vessel. However, the cornea, with a diameter of between 11 and 12 mm, is a unique example. It has been tried to explain the notable absence of blood vessels in the cornea, arguing that corneal tissues are able to take oxygen directly from the air. In this article we are explaining that based on the physicochemical characteristics of molecular oxygen and the cell membrane, cytoplasm, water, and cellular metabolism, it is not possible that epithelial corneal cells directly take oxygen from the air, instead, corneal cells have molecules that can dissociate the water molecules thereby these cells, like any other eukaryotic cells, take the oxygen from the intracell water, like plants.

Perovskite Solar Cell (PSC) is a third-generation photovoltaic device known for its rapid improvement in efficiency levels over the past decade. Moreover, the added benefits of abundant sourcing of raw materials, uncomplicated fabrication process, organic and inorganic device materials, and tuneable bandgaps make this technology a sustainable energy alternative. However, the efficiency values of these devices are subjected to variation depending on factors such as material compatibility, environmental conditions, energy band alignment of device components and stability characteristics to extrinsic and intrinsic factors. One such vital intrinsic factor is film morphology, homogenous and superior film quality formation and pinhole and trap-free films. In this study, we have investigated the formation of perovskite films on a qualitative basis using metal chloride washing of salts such as Erbium, Antimony, Cadmium and Chromium Chloride. The study aims to analyse the difference in film formation with various metal chloride washing and how this could potentially impact or contribute to photovoltaic performance if the devices are fabricated.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

Abstract: Molybdenum (Mo) thin films were sputtered from two kinds of Mo targets with different microstructures under the same sputtering process, and the effect of microstructure of Mo target on morphology, deposition rate and resistance of sputtered film were studied and discussed. The results show that morphological differences between Mo thin films sputtered by Mo targets with different microstructures are very small. The more uniform and finer the grain structures of Mo target, the better the uniformity on thickness and resistance of Mo sputtered film. Moreover, during sputtering process, when Mo target’s grain size is finer and the surface area of grain boundary is higher, the thickness reduction of the target is more homogeneous and the sputtering film has faster deposition velocity. The difference in microstructure of the Mo target has not obvious influence on the grain orientation of sputtering film.

tructural and superconducting properties of high quality Niobium nanofilms with different thicknesses are investigated on silicon oxide and sapphire substrates. The role played by the different substrates and the superconducting properties of the Nb films are discussed based on the defectivity of the films and on the presence of an interfacial oxide layer between the Nb film and the substrate. The X-ray absorption spectroscopy is employed to uncover the structure of the interfacial layer. We show that this interfacial layer leads to a strong proximity effect, specially in films deposited on a SiO2 substrate, altering the superconducting properties of the Nb films. Our results establish that the critical temperature is determined by an interplay between quantum-size effects, due to the reduction of the Nb film thicknesses, and proximity effects.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

Heating films were prepared by using poly(methyl methacrylate) and polybutadiene composites containing graphite. The heating film was prepared by casting the as-made polymer composite on PET film. Copper electrodes were attached to both ends of the as-prepared film, and the heating characteristics of the film was analyzed while applying DC voltage. The electrical conductivity and the heating temperature of the heating films depended on the size, the structure, the content and the dispersion characteristics of the graphite in the composite. The electrical resistance of the heating film was controlled to adjust the heating temperature of the film. The relationship between the physical/chemical structure and the heating characteristics of the composite film was studied by measuring the heating temperature as functions of film thickness and resistance by using an infrared thermal imaging camera. The lower the film resistance, the higher the heating temperature of the film. The surface temperature was uniform throughout the film.

Solar energy has emerged as a promising alternative to traditional fossil fuels due to its abundant availability and sustainability. Solar cells, the fundamental units of solar energy conversion, have undergone significant advancements in fabrication techniques to enhance their efficiency, durability, and cost-effectiveness. This review aims to provide a comprehensive overview of various methods employed in the preparation of solar cells, including thin-film, crystalline silicon, organic, and perovskite-based technologies. By analyzing recent research developments, challenges, and future prospects, this article sheds light on the evolving landscape of solar cell fabrication, contributing to the ongoing efforts in achieving widespread adoption of solar energy.

An influenza A virus (H3N2) with an envelope with the same structure as COVID-19 was used for antiviral testing of material surfaces, in comparison with some results of feline calicivirus. The evaluation method used was the film adhesion method, in which the virus solution is placed on the material and adhered to it using a film. The evaluation method was based on the film adhesion method, in which the virus solution is placed on the material and adhered with a film, and the plaque method, in which the cell virus is allowed to infect the material and form plaques, but the appropriate virus concentration must be adjusted to observe the plaques. When not under that restriction, the plaques are often incomplete; this is observed. For this reason, this study applied an area measurement method that can reflect viral activity even when plaques are not obtained. This study revealed that different types of metallic materials have different antiviral properties. Specifically, the antiviral activity of iron, carbon steel, and nickel was relatively high, while that of stainless steel and titanium was relatively low. The order of antiviral activity was as follows: Fe, SS400, Ni, SUS316L, SUS304, and Ti.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

Valsartan (Val) is an important antihypertensive medication with side effects such as dizziness and angioedema. These constraints are due to the low oral bioavailability and relatively short half-life. The goal here is to incorporate Val into a mixed micelles system that can enhance transdermal delivery. Thin-film hydration and micro-phase separation were used to produce Val-loaded mixed micelle systems. A variety of factors, including surfactant type and drug-to-surfactant ratio, were optimized to produce micelles with low size and high Val entrapment efficiency (EE). The size, polydispersity index (PDI), zeta-potential, and drug entrapment efficiency of the prepared micelles were all measured. The drug release profiles in vitro were assessed using dialysis bags, and the permeation through abdominal rat skin was assessed using a Franz diffusion cell. All formulations had high EE levels exceeding 90% and low particle charges. The micellar sizes ranged from 107.6 to 191.7nm, with average PDI values of 0.3. The in vitro release demonstrated a uniform slow rate that lasted one week with varying extents. F7 demonstrated a significant (P < 0.01) transdermal efflux of 68.84 ± 3.96 µg/cm2/h through rat skin when compared to the control. As a result, the enhancement factor was 16.57. Val-loaded mixed micelles were successfully prepared using two simple methods with high reproducibility, and extensive transdermal delivery was demonstrated in the absence of any aggressive skin modifying enhancers.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

In the present work we have investigated an organic semiconductor based on tris(8-hydroxyquinoline) aluminum (AlQ3) doped with tetracyanoquinodimethane (TCNQ), which can be used as a photoactive layer in organic light-emitting device (OLED). DFT calculations were carried out to optimize the structure of semiconductor species and get related constants in order to compare experimental and theoretical results. The semiconductor AlQ3-TCNQ was structurally characterized and their experimental IR spectrum was compared with that obtained through DFT calculations. Subsequently, AlQ3-TCNQ films with polypyrrole (PPy) matrix were fabricated, they were morphologically and mechanically characterized by Scanning Electron and Atomic Force Microscopy techniques. The maximum stress for the film is 8.66 MPa and the Knoop hardness is 0.0311. The film was analyzed in its optical behavior and the optical properties of hybrid film were found to exhibit two indirect allowed transitions at 2.64 and 3.44 eV. Finally, an OLED type was fabricated that was electrically characterized. Applying a cubic-spline approximation to fit cubic polynomials to the J-V curves, the ohmic to SCLC transition voltage VON and the trap-filled-limit voltage VTFL for the device were obtained. Then, the free carrier density and trap density for the device were approximated to n0=2.4787×10171m3 and Nt=1.7419×10291m3 respectively.

In this study we assessed the electrical and optical behavior of semiconductor hybrid films fabricate from octaethyl-21H,23H-porphine copper (CuP), embedded in polymethylmethacrylate (PMMA), and polystyrene (PS). The hybrid films were characterized structurally and morphologically by means of Infrared spectroscopy (IR), atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Subsequently, the PMMA:CuP and PS:CuP hybrid films were evaluated optically by UV-vis spectroscopy, as well as electrically, with the four-point collinear method. Hybrid films present a homogeneous and low roughness morphology, besides; the PS matrix allows the crystallization of the porphin, while the PMMA promotes the amorphous structure in CuP. The polymeric matrix also has an effect on the optical behavior of the films, since the smallest optical gap (2.16 eV) and onset gap (1.89 eV) and the highest transparency are obtained in the film with a PMMA matrix. Finally, the electrical behavior in hybrid films is also affected by the matrix: the largest amount of current carried is around 0.01 A for PS:CuP film, while for PMMA:CuP film it is 0.0015 A. Thanks to the above properties, hybrid films are promising candidates for use in optoelectronic devices.

We propose an experimental method for the unidirectional excitation of spin waves. By structuring Au nanowires arrays within a coplanar waveguide onto a thin yttrium iron garnet (YIG) film, we observe a chiral coupling between the excitation field geometry of the nanowires grating and several well-resolved propagating magnon modes. We report a propagating spin wave spectroscopy study with unprecedented spectral definition, wavelengths down to 130 nm and attenuation lengths well above the 100 μm over the 20 GHz frequency band. The proposed experiment paves the way for future non-reciprocal magnonic devices.

Corn starch-based nanocomposite films usually have low moisture barrier properties. The addition of virgin coconut oil (VCO) as a hydrophobic component can improve the nanocomposite film's characteristics, especially the film's permeability and elongation properties. This study aimed to determine the role of VCO with various concentrations (0,3,5 wt%) on the physical, mechanical, and water vapor transmission characteristics of corn starch/NCC-based nanocomposite films. The results showed that the concentration of 3 wt% VCO was most effective in reducing the WVTR value of nanocomposite films with a value of 4.721 g/m2.h. While the value of tensile strength was 4.243 MPa, elongation 68.58%, modulus of elasticity 0.062 MPa, thickness 0.219 mm, lightness 98.77, and water solubility 40.51%. However, the addition of 5 wt% VCO was more effective in increasing the elongation properties of the film. The addition of VCO gave the appearance of a porous film surface and a finer structure was formed. The FTIR test on corn starch nanocomposite films with the addition of VCO did not show any new absorption peaks. The results of this study may provide opportunities for the development of nanocomposite films as biodegradable packaging in the future.

Additive manufacturing (AM) processes, including stereolithography (SL), can fabricate complex ceramic parts layer by layer using computer-aided design (CAD) models. A ceramic slurry with high solid loading is usually used in SL to fabricate the desired shape, which is further sintered to produce the final part. The traditional SL system utilizes a tank filled with printable material, known as a vat, which for ceramic slurry contributes several limitations and operational difficulties, and further renders it non-recyclable mainly due to its high viscosity and the fragility of the green state. In this study, we utilized a continuous film supply (CFS) printer integrated with a tape casting system using in-house-designed ceramic slurry to print standard prototype specimens. Various printing parameters, including viscosity, layer thickness control, and slurry recycling efficiency, were studied. In addition, post-processing optimizations of the prototype, characterizations, and the microhardness of sintered samples were studied to determine their properties and compare them with traditional methods. The effectiveness of slurry reusability was demonstrated by printing with original and recycled slurry to produce consistent densification of final parts. Post-processing was optimized to achieve a relative sinter density of 99.02% and microhardness of 12.59 GPa. This method provides new opportunities to realize dense complex ceramic features with final properties comparable to those produced by subtractive machining and traditional SL. Furthermore, slurry recycling helps to reduce the overall cost and material consumption.

The concept of this prototype is to create a cold air film layer, in indoor side of the window. The function of this extra cold air layer is to increase the amount of window resistance and decrease its U-Value. It provide air film layer by using the same concept of desert cooler or wind catcher. They both bring the hot air from outside then let it go throw straw miost with cold water. After hot air move through straw, it would become cold, thus increase the window resistance and decrease the haet gian, therefore, decrease the cooling load. So, this window model works by heating the air in air room by sun radiation, then after a while, air pressure will rise and its volume will increase then it will impulse to wet hay, and become cold. Then there is fins to guide air flow to its correct direction, thus inner side of window will become cold, not like other type of window which when temperature rise, the inner side of window become hot. So, this window prevents heat transition and creare regenereted trubouland air flim in the inner side of the window. Using calculation to find air film characteristics and WINDOW7.7 software to calculate heat gain through window, shows that it is expected from this prototype to reduce heat gain by 6.85 % for double glazed clear window.

Active films based on carboxymethyl chitosan incorporated corn peptide were developed. Physicochemical properties of the films, including thickness, opacity, moisture content, color, mechanical properties, water vapor permeability, and oil resistance, were measured. Biological activities of the films, including the antioxidant and antibacterial activities, were characterized in terms of 2, 2-diphenyl-1-picrylhydrazyl free radical scavenging activity, reducing power, the total antioxidant activity, and the filter disc inhibition zone method. The results indicated that the incorporation of corn peptide caused interactions between carboxymethyl chitosan and corn peptide in Maillard reaction and gave rise to the films light yellow appearance. Compared with the Control, the degree of glycosylation, browning intensity, thickness, opacity, tensile strength, antioxidant activity, and antibacterial activity of films were increased, but the elongation, vapor permeability, and oil resistance of films were decreased. The films based on corn peptide and carboxymethyl chitosan can potentially be applied to food packaging.

Diamond is a material with excellent performances which attracts the attention from researchers for decades. Pt (111), owing to its catalytic activity on diamond synthesis, is regarded to be a candidate for diamond hetero-epitaxity, which can enhance nucleation density. Molten surface at diamond growth temperature can also improve mobility and aggregation capability of primitive nuclei. Generally, (100)-oriented is welcomed for the achivement of high quality and large size diamond, since the formation of defects and twins are prevented. First-principle calculations and experimental researches were carried out for the study of transformation of orientation. The transformation from {111} to {100}-oriented diamond has been observed on Pt (111) substrate, which can be promoted by the increase of carbon source concentration and substrate temperature. The process is energetic favorable, which may provides a way towards large-scale (100) diamond films.

In this paper, we study the sensing performance of metasurfaces comprised by spiral-disk-shaped metallic elements patterned on polypropylene substrates, which exhibit localized surface plasmon resonances in the low-frequency region of the THz spectrum (0.2-0.5 THz). Optimal designs of spiral disks with C-shaped resonators placed near the disks were determined and fabricated. The experimentally measured transmittance spectra of samples coated with very thin photoresistive layers (d ~ 10^-4-10^-3 λ) showed good agreement with simulations. The resonance frequency shift Δf increases with increasing d, while saturating near d = 50 µm. The narrow-band magnetic dark modes excited on symmetrical spiral disks with a 90⁰-C-resonator demonstrated very high FOM values reaching 1670 [RIU·mm]^-1 at 0.3μm-thick analyte. The hybrid high order resonances excited on asymmetrical densely packed spiral disks showed about two times larger FOM values (up to 2950 [RIU·mm]^-1) as compared to symmetrical distantly spaced spirals that resembles the best FOM results found in literature for metasurfaces fabricated with a similar technique. The demonstrated high sensing performance of spiral disks is evaluated to be promising for bio-sensing applications in the THz range.

An effort was made to find a relationship between the ratio of average asperities height and lubricant thickness at the point of contact of rolling element ball bearings, and empirical equations to predict the life for bearings under constant motion. Two independent failure mechanisms were considered, fatigue failure and lubricant failure resulting in seizing of the roller bearing. A theoretical formula for both of these methods was established for the combined probability of failure using both of these failure mechanisms. Fatigue failure was modeled with the empirical equations of Lundberg and Palmgren and standardized in DIN/ISO281. The seizure failure, which this effort sought to investigate, was predicted using Greenwood and Williamson's theories on surface roughness and asperities during lubricated contact. These two mechanisms were combined, and compared to predicted cycle lives of commercial roller bearing, and a clear correlation was demonstrated. This effort demonstrated that the Greenwood-Williams theories on the relative height of asperities versus lubricant film thickness can be used to predict the probability of a lubricant failure resulting in a roller bearing seizing during use.

ZnO films with Ti atoms incorporated (TZO) in a wide range (0-18 at. %) have been grown by reactive co-sputtering on silicon and glass substrates. The influence of the titanium incorporation in the ZnO matrix on the structural and optical characteristics of the samples has been determined by Rutherford backscattering spectroscopy (RBS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results indicate that the samples with low Ti content (< 4 at. %) exhibit the wurtzite-like structure, with the Ti+4 ions substitutionally incorporated into the ZnO structure, forming Ti-doped ZnO films. In particular, very low concentration of Ti (<0.9 at. %) leads to a significant increase of the crystallinity of the TZO samples. Higher Ti contents give rise to a progressive amorphization of the wurtzite-like structure so samples with high Ti content (≥18at. %), displays an amorphous structure indicating the XPS analysis a predominance of Ti-O-Zn mixed oxides. The energy gap, obtained from absorption spectrophotometry, increases from 3.2 eV for pure ZnO films to 3.6 eV for those with the highest Ti content. Ti incorporation in the ZnO samples below 0.9 at. % rises both, the blue (380 nm) and green (550 nm) bands of the photoluminescence (PL) emission, thereby indicating a significant improvement of PL efficiency of the samples.

An effort was made to find a relationship between the predicted tribological conditions at the point of contact of ball bearings, and empirical equations to predict the life for bearings under constant motion. The model was modified to predict the temperature dependence, and compare rapid accelerations and decelerations with empirical extrapolations.

This study presents an instant preview and analysis system implementation of intelligent stereo cameras (ISCs). A parameter optimization prototype adopted the instant preview and analysis system of the ISCs has been achieved the automatic alignment function, and obtained optimal stereo films with the automatic alignment function by adjusting gap and angle between dual cameras. The instant preview and analysis system of the ISCs with parameter optimization can enhance the quality of stereo films effectively and reduce filmed errors and save retouched cost and time in harsh filmed environment.

Stenting is an alternative to endarterectomy for the treatment of carotid artery stenosis. However, stenting is associated with a higher risk of procedural stroke secondary to distal thromboembolism. Hybrid stents with a micromesh layer have been proposed to address this complication. We developed a micropatterned thin film nitinol (M-TFN) covered stent designed to prevent thromboembolism during carotid intervention. This innovation may obviate the need or work synergistically with embolic protection devices. The proposed double layered stent is low-profile, thromboresistant, and covered with a M-TFN that can be fabricated with fenestrations of varying geometries and sizes. The M-TFN was created in multiple geometries, dimensions, and porosities by sputter deposition. The efficiency of various M-TFN to capture embolic particles was evaluated in different atherosclerotic carotid stenotic conditions through in vitro tests. The covered stent prevented emboli dislodgement in the range of 70-96% during 30min duration tests. In vitro vascular cell growth study results showed that endothelial cell elongation, alignment and growth behaviour silhouettes significantly enhance specifically on the diamond-shape M-TFN with the dimensions of 145µm×20µm and a porosity of 32%. Future studies will require in-vivo testing. Our results demonstrate that M-TFN has a promising potential for carotid artery stenting.

Electrostatic endothelial cell seeding has evolved as an exceptional technique to improve the efficiency of cell seeding in terms of frequency of attached cells and the amount of cell adhesion for the treatment of vascular diseases. In the recent times, both untreated and superhydrophilic thin film nitinol (TFN) have exhibited strong prospect as substrates for creation of small-diameter endovascular grafts due to their hallmark properties of superelasticity, ultra low-profile character, grown hemocompatible oxide layer with the presence of a uniform endothelial layer on the surface. The purpose of the current study is to understand the effects of endothelial cell seeding parameters (i.e., applied voltage, incubation time, substrate chemistry and cell suspension solution) to investigate the cell seeding phenomenon and to improve the cell adhesion and growth on the TFN surface under electrostatic transplantation. Both parallel plate and cylindrical capacitor models were used along with the Taguchi Design of Experiment (DOE) methods to design in vitro test parameters. A novel in vitro system for cylindrical capacitor model was created using a micro flow pump, micro incubation system, and silicone tubings. The augmented endothelialization on thin film nitinol was developed to determine the effect of cell seeding and deployed in a 6 Fr intravascular catheter setup. Cell viability along with morphology and proliferation of adhered cells were evaluated using fluorescent and scanning electron microscopy. Our results demonstrated that the maximum number of cells attached on STFN in the catheter was observed in 5V with the 2 hr exposure of in the cell culture medium (CCM) solution. The condition showed 5V voltage with 0.68×10-6 µC electrostatic charge and 5.11 V·mm-1 electric field. Our findings have first demonstrated that the electrostatic endothelialization on the superhydrophilic thin film nitinol endograft within the catheter prior to the endovascular procedure could enhance the biocompatibility for low-profile endovascular applications.

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

With the escalating water scarcity in agriculture, a novel water-saving technique has emerged: drip irrigation with plastic-film mulch (DI). Root function is crucial for sustaining rice production, and understanding its response to DI is essential. However, few studies have evaluated root systems in rice varietals and examined which kind of root system contributes to improving rice grain yield and water productivity in DI. To fill this knowledge gap, we conducted a two-year field experiment comparing two irrigation systems: continuous flooding (CF) and DI. We analyzed their effectiveness with four rice varieties, including upland, F1 lowland, animal feed lowland, and lowland varieties. Vertical root distribution, root bleed-ing rate, photosynthetic-associated parameters, water productivity, and yield performance were analyzed. In our study, the average grain yield of varieties in the DI system (6.4t/ha) was equivalent to those in the CF system (6.6 t/ha). Compared to CF, DI demonstrated significant water-saving potential, saving approximately 35% of the total water supplied, resulting in higher water productivity. Among the varieties, the deep-root weight of the upland variety significantly increased by 51%. The deep-root ratio was positively correlated to transpiration rate, grain yield, and water productivity, which suggested that it contributed to high transpiration, thus maintaining a high carbon assimilation rate resulting in high yield and water productivity. Therefore, deep roots deserve consideration as a trait potentially corresponding to high yield under DI.

This work reports the first nanocrystalline SnON (7.6 % Nitrogen content) n-type nanosheet Field-Effect Transistor (nFET) with transistor’s effective mobility (µeff) as high as 357 and 325 cm2/V-s at electron density (Qe) of 5×1012 cm-2 and ultra-thin body thickness (Tbody) of 7 and 5 nm, respectively. At the same Tbody and Qe, these µeff values are significantly higher than single crystalline Si, InGaAs, thin-body Si-on-Insulator (SOI), two-dimensional (2D) MoS2 and WS2. New discovery of slower µeff decay rate at high Qe than SiO2/bulk-Si universal curve was found, owing to one order of magnitude lower effective field (Eeff) by more than 10 times higher dielectric constant () in channel material, which keeps the electron wave-function away from the gate-oxide/semiconductor interface and lowers the gate-oxide surface scattering. In addition, the high µeff is also due to the overlapped large radius s-orbitals, low 0.29 mo effective mass (me*) and low polar optical phonon scattering. SnON nFETs with record-breaking µeff and quasi-2D thickness enable potential monolithic three-dimensional (3D) integrated circuit (IC) and embedded memory for 3D biological brain-mimicking structures.

This experimental study investigates the effect of scarf geometry in restoring the impact response of scarf patched 3 mm thick glass-fibre reinforced polymer (GFRP) matrix composite laminates. Traditional circular along with rounded rectangular scarf patch configurations considered as repair patches. Experimental measurements revealed that the temporal variations of force and energy response of the pristine specimen are close to that of circular repaired specimens. The predominant failure modes were witnessed only in repair patch which include the matrix cracking, fibre fracture, delamination and no discontinuity in adhesive interface was witnessed. When compared with the pristine samples, the top ply damage size of the of the circular repaired specimens is larger by 9.91 %, while that of the rounded rectangular repaired specimens is larger by 434.23 %. The results show that circular scarf repair is more suitable choice of repair approach under the condition of 37J low-velocity impact event even though the global force-time response is similar.

Microplastics (MPs) and nanoplastics (NPs) are distributed and transferred among the four major environmental compartments (air, water, soil, and biota) and have been already found in humans, making crucial to develop remediation technologies to tackle this kind pollution. Photocatalysis can be used to eliminate MPs present in contaminated wastewater effluents before their discharge into waterbodies. In this work, several green TiO2-based semiconductors were prepared using the extrapallial fluid (EPF) of Mytilus edulis sea water mussels as doping precursor. The semiconductors were then used as films or powders to photocatalytically degrade polystyrene (PS) NPs and MPs and polyethylene (PE) MPs. It was found that the obtention of green TiO2-based semiconductors with good characteristics for photocatalytic purposes (anatase crystalline phase, presence of porosity, activity in visible light and high surface area) seems not enough to achieve high degradation efficiency. The operational conditions of the reaction system should be also taken into account. For instance, the convenience of using semiconductors in the form of films can be overcome by their limited exposed surface area or the null adsorption of the semiconductor in the MPs particles. Additionally, crystallinity of the semiconductor can be a more determinant factor to take into account when performing photocatalysis of MPs.

Starch is a biopolymer with wide potential for the generation of new biodegradable packages due to its high availability and low price. However, due to its weak functional properties, it is necessary to limit the interaction of some hydroxyl, and to evaluate blends with other polymers to improve their performance. Glycerol plasticized acetylated corn starch films were developed by the casting method, and the impact of incorporating chitosan (TPS:CH) at various proportions (75:25, 50:50, and 25:75 v/v) was studied. The effect of the chitosan ratios on the films' physical, mechanical, water vapor barrier, and thermal properties was evaluated. Chitosan protonated amino groups promote the formation of intermolecular bonds, improving the tensile strength, the thermal stability, the water adsorption capacity, and the gas barrier of starch films. Where the film composed of TPS25-CH75 was the one that presented the best barrier to water vapor. These composite films are a good option for development of biodegradable packaging.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

We utilized laser irradiation as a potential technique in tuning the electrical performance of NiOx/SiO2 thin film transistors (TFTs). By optimizing the laser fluence and the number of laser pulses, the TFT performance is evaluated in terms of mobility, threshold voltage, on/off current ratio and subthreshold swing, all of which were derived from the transfer and output characteristics. The 500 laser pulses irradiated NiOx/SiO2 TFT exhibited an enhanced mobility of 3 cm2/V-s from a value of 1.25 cm2/V-s for as-deposited NiOx/SiO2 TFT. The laser-irradiated NiOx material likely has a significant concentration of defect gap states, which could also be involved in light absorption processes. Second, and more importantly, the excess energy that the photogenerated charge carriers possess (due to the significant difference between the photon energy and the bandgap of NiOx), combined with the very high light intensity, would result in complex thermal and photo thermal changes thus resulting in an enhanced electrical performance of p-type NiOx/SiO2 TFT structure.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Electrodeposition of cadmium telluride (CdTe) on fluorine doped tin oxide (FTO) using two electrode configuration was successfully achieved with the main focus on the growth temperature. The electroplating temperatures explored ranges between (55 and 85)℃ for aqueous electrolytes containing 1.5 M cadmium nitrate tetrahydrate (Cd(NO3)2 •4H2O) and 0.002 M tellurium oxide (TeO2). The ensuing CdTe thin-films were characterised using X-ray diffraction (XRD), UV-Vis spectrophotometry, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and photoelectrochemical (PEC) cell measurements. The electroplated CdTe thin-films exhibit a dominant (111) CdTe cubic structure, while the crystallite size increases with the increase in the electroplating temperature. The internal strain, dislocation density and the number of crystallites per unit area decrease with increasing growth temperature. The optical characterization depicts that the CdTe samples show comparable absorbance and a resulting bandgap of 1.51±0.03 eV for as-deposited CdTe layers. A marginal increase in the bandgap and reduction in the absorption edge slope towards lower deposition temperatures were also revealed. The annealed CdTe thin-films showed improvement in energy bandgap as it tends towards 1.45 eV while retaining the aforementioned absorption edge slope trend. Scanning electron microscopy shows that the underlying FTO layers are well covered with increasing grain size observable relative to the increase in the deposition temperature. The energy dispersive X-ray analyses show an alteration in the Te/Cd relative to the deposition temperature. Higher Te ratio with respect to Cd was revealed at deposition temperature lower than 85℃. The photoelectrochemical cell study shows that both p- and n-type CdTe can be electroplated and that deposition temperatures below 85℃ at 1400 mV results in p-type CdTe layers.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

MAPLE (matrix assisted pulsed laser evaporation) depositions of Candida Rugosa lipase were carried out from ice matrices whose composition is optimized in order to minimize conformational damage of the protein, which strongly influences its catalytic activity. To induce lid opening and to protect lipase during the MAPLE process, pentane and m-DOPA amino acid were added to the liquid matrix giving a target formed by a frozen water-lipase-pentane microemulsion. FTIR and AFM were used to investigate the structure of MAPLE deposited lipase films. The ability of MAPLE films to promote transesterification was determined by thin layer chromatography. It was shown that m-DOPA has influence on the aggregation but not on the unfolding of lipase induced by MAPLE, while the microemulsion formed by the addition of pentane to the target composition is effective in protecting lipase during the MAPLE process. MAPLE deposited lipases showed a modified specificity.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

We report a new synthesis method for multiple walled nested thin film nanostructures by combining hydrothermal growth methods with Atomic Layer Deposition (ALD) thin film technology and sacrificial films thereby increasing the surface-to-volume ratio to improve the sensing performance of novel ZnO gas sensors. Single crystal ZnO nanorods serve as the core of the nanostructure assembly and were synthesized hydrothermally on fine-grained ALD ZnO seed films. Subsequently the ZnO core nanotubes were coated with alternating sacrificial co-axial 3-D wraparound ALD Al2O3 films and ALD ZnO films. Basically, an ALD 3-D wrap-around Al2O3 sacrificial layer was coating the center nanorod to realize a nested coaxial ZnO thin film nanotube. To increase the surface-to-volume ratio of the nested multiple film nanostructure both front and backside of the nested coaxial ZnO films must be exposed by selectively removing the intermittent Al2O3 sacrificial films. The selective removal of the sacrificial films exposes the front and backside of the free-standing ZnO films for interacting with target gases during sensing operation while steadily increasing the surface-to-volume ratio. The sensing response of the novel ZnO gas sensor architecture with nested nanotubes achieved a maximum 150% enhancement at low temperature compared to a conventional ZnO nanorod sensor.

Current-induced field-free magnetic switching using spin-orbit torque has been an important topic for decades due to both academic and industrial interest. Most research has focused on introducing symmetry breakers, such as geometrical and compositional variation, pinned layer, and symmetry-broken crystal structures, which add complexity to the magnetic structure and fabrication process. We designed relatively simple magnetic structure, composed of a [Co/Pt] multilayer and a Co layer with perpendicular and in-plane magnetic anisotropy, respectively, with a Cu layer between them. Current-induced deterministic magnetic switching was observed in this magnetic system. The system is advantageous for its easy control of the parameters to achieve the optimal condition for magnetic switching. The balance between magnetic anisotropic strength and interlayer coupling strength is found to provide the optimal condition. This simple design and easy adjustability opens various possibilities for magnetic structures in spin-based electronics applications using spin-orbit torque.

Human fungal pathogen Candida albicans causes oral infectious diseases such as oral thrush in immunocompromised patients with hyposalivation, diabetes mellitus, prolonged use of anti-biotics or immunosuppressive medicines and poor oral hygiene. An anti-fungal medication classified as a BCS class II drug, Clotrimazole has high permeability and low solubility in water. It is commercially available as lozenges, which do not uniformly distribute the drug within saliva for local therapy. This results in higher dose frequency and lower patient compliance. Therefore, in this study we proposed a niosomal based subgingival film formulation of clotrimazole for enhancing drug efficacy by improving drug solubilization capacity and improving patient compliance by prolonging the release of drug at the targeted site and reducing the dose frequency to show effective anti-fungal activity. The prepared niosomal film showed good entrapment efficiency and anti-fungal activity. Niosomal film showed better release pattern than drug loaded film.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

In this study, various diamine monomers were used to synthesize aramid polymer films via a low-temperature solution condensation reaction with diacid chloride. For diamines with relatively high basicity, the reaction system became opaque because amine salt formation inhibited polymer synthesis. Meanwhile, low-basicity diamines with strong electron-withdrawing groups, such as CF3 and sulfone, were smoothly polymerized without amine salt formation to provide highly viscous solutions. The acid byproduct HCl generated during polymerization was removed by adding propylene oxide to the reaction vessel and converting the acid into highly volatile inert substances. The resulting solutions were used as varnishes without any additional purification, and polymer films with an excellent appearance were easily obtained through a conventional casting and convection drying process. The films neither tore nor broke when pulled or bent by hand; furthermore, even when heated up to 400°C, they did not decompose or melt. Moreover, polymers prepared from 2,2-bis (trifluoromethyl) benzidine (TFMB) and bis (4-aminophenyl) sulfone (pAPS) did not exhibit glass transition until decomposition. The prepared polymer films showed a high elastic modulus of more than 4.1 GPa and a high tensile strength of more than 52 MPa. In particular, TFMB-, pAPS-, and 2,2-bis (4-aminophenyl) hexafluoropropane-based polymer films were colorless and transparent, with very high light transmittances of 95%, 96%, and 91%, respectively, at 420 nm and low yellow indexes of 2.4, 1.9, and 4.3, respectively.

The application of dry lubrication in rolling contacts is challenging due to wear. In previous studies graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. The applied graphene platelets have a thickness of few graphene layers in the nm range and a diameter in the µm range. Such platelets can be produced by mechanical exfoliation from graphite. To delve deeper into the lubrication effects, investigations were carried out using a milli tribometer. In the tests, a fixed steel ball is sliding against an oscillating counterpart under defined load. During the measurements, the applied load and tangential forces on the ball are recorded to calculate the friction. In our case, a steel ball with a diameter of 6 mm was used against graphene-based films on flat bearing surfaces (axial bearing washer). Comparative investigations included nano graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. On the ball as counterpart, the graphene platelets generate a transfer film on the contacting surface.

Zirconium dioxide (ZrO2) possesses numerous advantages such as high mechanical strength, low friction coefficient, excellent optical properties, and extended lifespan. Consequently, ZrO2 has a broad research foundation and practical significance in functional films and wear-resistant coatings. However, it suffers from brittleness and low ductility when used as a bio-coating material. In this study, a Ta/ZrO2 film was fabricated on Si (100) and titanium alloy substrates using a magnetron sputtering system, with tantalum (Ta) serving solely as a transition layer. Subsequently, Zr and Nb ions were implanted into the film at varying doses but with consistent energy levels. The analysis focused on the film's microstructure, mechanical properties, hydrophilicity, and corrosion resistance. The results demonstrated a significant improvement in the hydrophilicity and corrosion resistance of the ZrO2 film following the implantation of Zr and Nb ions. First-principles calculations based on density functional theory (DFT) principles indicated that, with increasing doping concentrations of Zr and Nb in the ZrO2 model, the stability of the model increased gradually, thereby enhancing its corrosion resistance.

During shearer operation, piston rod is susceptible to wear from invasion of pollutants, and then ruins sealing ring in hydraulic cylinder. This work attempts to conduct a systematical investigation of Cu-DLC (Cu-doped Diamond-like Carbon) film to improve the seal performance. Failure process of hydraulic cylinder was analyzed, and relevant parameters were determined. Several Cu-DLC films were deposited on the substrate of piston rod in a multi-ion beam assisted system, and their structures and combined tribological performances were investigated. As a result, dust particles attached to the piston rod may enter the cylinder, and damage the sealing ring under the radial force. Cu grains prefer to orientate (111) crystal plane with increase of Cu content, and may induce drop of hardness and internal stress for the film. Friction coefficient of the film ranges from 0.04 to 0.15, and rise of IG/ID ratio from 1.4 to 2.3 in Raman data indicates that bond transition from sp3-C to sp2-C may lower the friction coefficient. Modification mechanism of Cu-DLC film for the seal performance may come from synergistic effects of (i) contact force and friction heat induce the film graphitization, (ii) Cu doping improves toughness of the film and acts as a solid lubricant, and (iii) transfer layer plays a role of self-lubrication.

Bismuth sodium titanate thin films (BNT) were deposited on Pt/SiN substrates by Sol-Gel spin coating technique under O2 atmosphere. Microstructural, structural, and electrical properties of the obtained film were investigated. Scanning electron microscopy and atomic force microscopy micrographs were used to analyze the microstructure of the films. Furthermore, EDX analysis revealed a Na-deficient composition for the obtained film. X-ray diffraction and Raman spectroscopy allowed the identification of a pure perovskite BNT phase. Dielectric, ferroelectric, and leakage current measurements revealed good frequency stability of the dielectric constant and dielectric losses for BNT thin film. The results are discussed in terms of Na-deficiency effects on the defect structure of BNT. Further, the film showed attractive electrostatic energy storage properties with energy density that exceeds 1.04 J/cm3 under E = 630 kV/cm.

The aim of this work is to synthesis and characterize the Ta/TaN multilayer thin film coatings on 52100 tool steel under three different levels of N2 gas flow rate. The High Power Impulse Magnetron Sputtering (HiPIMS) technique was used for the deposition of Ta/TaN thin film multilayers on the substrate. Microstructure, coating thickness, composition, hardness and tribological properties of Ta/TaN multilayer coatings were characterized using scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester and pin-on-disc tester, respectively. Adhesion property was evaluated via scratch testing of the thin film thin film layer. The lowest coefficient of friction was observed with the thin film layer of higher N2 gas flow rate due to the highest adhesion value of the coating on the surface. The obtained results on hardness, adhesion and coefficient of friction properties demonstrated that this Ta/TaN multilayer thin film coating can be used for tribological applications.

Bio-based packaging materials and efficient drug delivery systems are gaining attention, carboxymethyl cellulose (CMC) is one of the most soluble cellulose derivatives, is a good candidate material due to its biocompatibility, biodegradability, and reproducibility. However, CMC-based films are lack of sufficient mechanical properties, limiting its widespread application. In this paper, the molecular interactions between CMC and additives with different molecular structures have been studied with rheological method. The additives are chitosan and cellulose derivatives including O-carboxymethylated chitosan (O-CMCh), N-2-hydroxypropyl-3-trimethylammonium-O-carboxymethyl chitosan (HTCMCh), hydroxypropyltrimethyl ammonium chloride chitosan (HACC), cellulose nanofibers (CNC), and cellulose nanofibers (CNF). The influencing factors, such as molecular structure, concentration of additives and temperature on the rheological properties were studied, which results revealed the information intermolecular interactions. Based on the rheological properties, several systems were selected to prepare films, which show very good transparency, wettability, mechanical properties, biodegradability, and cytotoxicity. These good characteristics of the selected films also proved the good biocompatibility of CMC and chitosan and cellulose derivatives. This work will provide an idea to prepare CMC-based food packaging and effective drug delivery materials with specific properties.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

Marangoni flow in foam fractionation in the lamellar film for the interior and exterior of a micro-foam was investigated. The three-dimensional node-film-Plateau Border system was modeled using computational fluid dynamics. The importance of the surfactant concentration of the foam fractionation column and air-liquid interface mobility on the Marangoni velocity in the film was emphasized. The study found that an increase in surfactant concentration in the reflux column significantly increases the Marangoni velocities. Additionally, a mobile interface results in a higher Marangoni flow, while a rigid interface leads to less intensive flow. The behavior of the Marangoni flow in both interior and exterior foam was explored, revealing that the flow in exterior foam has different behavior due to the presence of the wall, which reduces the Marangoni velocity compared to interior films.

This paper considers the principles of building a circuit model of film resistor cutting. The conductive resistive medium is defined with the component equations and the topology of the circuit model. A method of estimating the electric parameters of a resistor operating in the system with a measuring voltage source is shown. An equation system for the node voltages is defined, and the resistive layer parameters are analyzed as the circuit model structure changes during the cutting process.

Many strategies have been developed for the synthesis of silicon carbide (SiC) thin films on silicon (Si) substrates by plasma-based deposition techniques, especially plasma enhanced chemical vapor deposition (PECVD) and magnetron sputtering, due to importance of these materials for microelectronics and related fields. A drawback is the large lattice mismatch between SiC and Si. The insertion of a thin aluminum nitride (AlN) buffer layer between them has been shown useful to overcome this problem. Herein, the high-power impulse magnetron sputtering (HiPIMS) technique was used to grow SiC thin films on AlN/Si substrates. Furthermore, the SiC films were also grown on Si substrates. Comparisons of the structural and chemical properties of SiC thin films grown on the two types of substrates allowed us to evaluate the influence of AlN buffer layer on such properties. The chemical composition and stoichiometry of the samples were investigated by Rutherford backscattering spectrometry (RBS) and Raman spectroscopy, while the crystallinity was characterized by grazing incidence X-ray diffraction (GIXRD). Our set of results evidenced the versatility of HiPIMS technique to produce polycrystalline SiC thin films at near room temperature only varying the discharge power. In addition, this study opens up a feasible route for the deposition of crystalline SiC films with a good structural quality using AlN buffer layer.

Low temperature cofired ceramics (LTCC) have conquered a niche segment in biological microelectromechanical systems (BioMEMS) during the last two decades. Since 3-dimensional assembly and rapid prototyping capability are outstanding features of the technology, bioreactors with complex geometry can easily be produced. Particularly needed functions are working electrodes, e.g. for impedance measurements and reference electrodes consisting in platinum or silver-silver chloride. Although the distinct grainy surface of thick film materials influences the double layer properties, data describing the bioelectronic interface and biocompatibility of common thick film materials are rarely published up to now. This works aims to fill this gap by studying the surface properties, composition, electrochemical properties and biocompatibility of commercially available thick film materials. It was found that thick film gold is suitable as electrode material in direct cell contact since an appropriate proliferation of the cell culture was observed. Poly(3,4-ethylenedioxythiophene) coating decreases the absolute value of the zeta potential of thick film gold from 16.55 V to 11.78 mV without any change in vitality of the cells. Thick film platinum layers have a porous structure entailing an enlargement of the effective surface by a factor of 21.6 and can be used as reference instead of silver/silver chloride, which was identified to be incompatible with cell culture. The investigations show that some commercially available cost-effective thick film materials are compatible with cell culture and the here presented data give an orientation for the use of the same in LTCC bioreactors.

In this work, unmodified screen-printed electrode (bare SPE) and Sb-film modified SPE (SbFSPE) sensors were employed for the analysis of trace amounts of Pb(II) in non-deaerated water solutions. The modified electrode was performed in situ in 0.5 mg/L Sb(III) and 0.01 M HCl. The methodology was validated for an accumulation potential of –1.1 V vs. Ag/AgCl and an accumulation time of 60 s. A comparative analysis of bare SPE and SbFSPE showed that the detection and quantification limits decrease for the bare SPE. The method with the bare SPE showed a linear response in the 69.8–368.4 µg/L concentration range, whereas linearity for the SbFSPE was in the 24.0–319.1 µg/L concentration range. This work also reports the reason why the multiple standard addition method instead of a linear calibration curve for Pb(II) analysis should be employed. Furthermore, the analytical method employing SbFSPE was found to be more accurate and precise compared to the use of bare SPE when sensors were employed for the first time, however this performance changed significantly when these sensors were reused in the same manner. Furthermore, electrochemical impedance spectroscopy was used for the first time to analyse the electrochemical response of sensors after being used for multiple successive analyses. Surface characterisation before and after multiple successive uses of bare SPE and SbFSPE sensors, with atomic force microscopy and field emission scanning electron microscopy, showed sensor degradation. The interference effect of Cd(II), Zn(II), As(III), Fe(II), Na(I), K(I), Ca(II), Mg(II), NO₃^– Bi(III), Cu(II), Sn(II), and Hg(II) on the Pb(II) stripping signal was also studied. Finally, the application of SbFSPE was tested on a real water sample (from a local river), which showed high precision (RSD = 8.1%, n = 5) and accurate results.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

The authors recently proposed a method for on-site dosimetry by a combination of radiochromic film and portable colorimeter. To test and expand the applicability of this method, dosimetric properties of radiochromic reactions were examined for six combinations of two popular Gafchromic films (EBT3 and EBT-XD) and three commercially-available portable colorimeters (nix pro2, nix spectro2 and Spectro1 Pro; abbreviated to “NixP”, “NixS” and “SpoP”, respectively). EBT3 and EBT-XD were irradiated with 160 kV X-rays at 0.3 to 40Gy and 1 to 80 Gy, respectively, and the radiation-induced color levels of RGB and CMMK components were measured with the three colorimeters. Angle dependence was examined by reading at 15° intervals. As results, it was judged that all combinations would work effectively as tools for on-site dosimetry. NixP and NixS showed advantages that they were applicable to a wider dose range for both films, while Spo1 worked better in a lower dose range. On the other hand, Spo1 had an advantageous feature of no angular dependence in reading films, while NixP and NixS showed significant angle-dependent changes. These differences were presumed to attribute to the different geometries of LED light emission; it came from all directions (ring-shape source) in Spo1, 4 directions in NixP, and 8 directions in NixS. These findings would expand the applicability of the proposed on-site dosimetry method to various occasions.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

Light-colored and transparent polyimide (PI) films with good high-temperature dimensional stability are highly desired for advanced optoelectronic applications. However, in practice, the simultaneous achievement of good optical and thermal properties in one PI film is usually difficult due to the inter-conflicting molecular design for the polymers. In the present work, a series of PI-SiO2 nanocomposite films (ABTFCPI) were developed based on the PI matrix derived from hydrogenated pyromellitic anhydride (HPMDA) and an aromatic diamine containing benzanilide and trifluoromethyl substituents in the structure, 2,2'-bis(trifluoromethyl)-4,4'-bis[4-(4-aminobenzamide)]biphenyl (ABTFMB). The inorganic SiO2 fillers were incorporated into the nanocomposite films with the form of colloidal nanoparticles dispersed in the good solvent of N,N-dimethylacetamide (DMAc) for the PI matrix. The derived ABTFCPI nanocomposite films showed good film-forming ability, flexible and tough nature, good optical transparency, and good thermal properties with the loading amounts of SiO2 up to 30 wt% in the system. The ABTFCPI-30 film with the SiO2 content of 30 wt% in the film showed the optical transmittance of 79.6% at the wavelength of 400 nm (T400) with a thickness of 25 μm, the yellow index (b*) of 2.15, and the 5% weight loss temperatures (T5%) of 491 oC, which are all comparable to those the pristine ABTFCPI-0 matrix without filler (T400=81.8%; b*=1.77; T5%=492 oC). Meanwhile, the ABTFCPI-30 film exhibited obviously enhanced high-temperature dimensional stability with the linear coefficients of thermal expansion (CTE) of 25.4×10-6/K in the temperature range of 50 to 250 oC, which is much lower than that of the AMTFCPI-0 film (CTE=32.7×10-6/K).

Owing to the escalating adoption of IoT systems across various domains, the demand for mobile and wireless power sources has surged. Although conventional batteries typically serve as energy storage components, the current low-power consumption devices necessitate eco-friendly alterna-tives. In this study, we designed, fabricated, and characterized an energy harvesting device that repurposes mechanical vibrations. A three-beam design was employed to harvest energy across a broader range of potential frequencies. Finite element models were simulated to ascertain the first bending moment for both sets of beams. A nanostructured piezoelectric multilayer film made of ZnO was deposited onto an AISI 304 steel substrate, and a photosensitive resin seismic mass was implemented. Low-cost techniques generating minimal environmental waste were leveraged in the fabrication process. The piezoelectric film was deposited using a spray nebulization technique involving recycled materials and cost-effective equipment. Micrographs of the layers unveiled the presence of nanospheres with diameters of 250 nm. Employing a custom-made shaker, output voltages of 1.08 V and 180 mV, and power outputs of 1.849 µW and 16.2 nW were achieved for each set of beams. The electrical characterization was conducted using a custom-made shaker, repurposing materials for this objective.

Abstract: To reduce the indiscriminate use of pesticides and extend the postharvest shelf life of peach fruit (cv. Baihua) from southeast China, microbial antagonism of indigenous yeasts was mainly studied and applied in construction of composite film. After isolation, purification, cultivation and identification, a total of 14 yeast strains from 9 genera were screened out from the surface of peaches. By experimental analysis of in vitro inhibition zone and in vivo colonizing capacity, Candida oleophila sp-ELPY12B and Cryptococcus laurentii sp-ELPY15A, which have conservative structure of D1/D2 domain sequences and were considered as new species by phylogenetic analysis, were finally chosen as fungicides against the major pathogens. In combination of Na-alginate film (0.4 % glycerin as plasticizer and 0.1 % Tween-80 as emulsifier), the preservative effects of composite-treated groups (1 × 108 CFU mL−1 of Candida oleophila sp-ELPY12B and Cryptococcus laurentii sp-ELPY15A) showed best antifungal effects, which significantly delayed the postharvest preservation period about 6 - 7 d under ambient temperature of 25 ± 3°C and relative humidity of 50 - 70%.