Extra virgin olive oil (EVOO) is the highest quality of olive oil and is characterized by highly beneficial nutritional properties. The large increase in both consumption and fraud, for example through adulteration, creates new challenges and an increasing demand for developing new quality assessment methodologies that are easier and cheaper to perform. As of today, the determination of olive oil quality is performed by producers through chemical analysis and organoleptic evaluation. The chemical analysis requires the advanced equipment and chemical knowledge of certified laboratories, and has therefore a limited accessibility. In this work a minimalist, portable and low-cost sensor is presented, which can perform olive oil quality assessment using fluorescence spectroscopy. The potential of the proposed technology is explored by analyzing several olive oils of different quality levels, EVOO, virgin olive oil (VOO), and lampante olive oil (LOO). The spectral data were analyzed using a large number of machine learning methods, including artificial neural networks. The analysis performed in this work demonstrates the possibility of performing classification of olive oil in the three mentioned classes with an accuracy of 100%. These results confirm that this minimalist low-cost sensor has the potential of substituting expensive and complex chemical analysis.

Treatment with tumor-selective photosensitive substances, such as photodynamic therapy and photoimmunotherapy, has been reported to enable the visualization of tumor drug accumulation in real time and identify the required light irradiation dose by fluorescence imaging. However, fluorescence observation is difficult during treatments performed under gastrointestinal endoscopy because of the challenges associated with including the fluorescence filter in the camera part. To address this issue, this study developed a device that integrates a narrow camera and a laser diffuser to enable fluorescence imaging through a forceps port. This device was employed to demonstrate that a laser diffuser with an NIR fluorescence imaging sensor could be delivered through a 3.2-mm-diameter port. In addition, fluorescence images of Cetuximab-IR700 were successfully observed in two mice, and the fluorescence intensity confirmed that the fluorescence decayed within 330 s. This device is expected to have practical application as a tool to identify the optimal irradiation dose for tumor-selective photosensitive substances under endoscopy.

Histidine is an essential amino acid with significant implications in human growth and neuromodulation. Its concentration within cells, when either elevated or reduced, can indicate different diseases. While various methods exist to measure increased histidine levels, there remains a significant lack of sensors capable of actively responding to histidine deficiency within cells and releasing strong signals. In this study, we exploited the high induction levels of the his operon in S. Typhimurium SL1344, a histidine auxotroph, within a histidine-deficient environment, to develop a specific bacterial sensor with sensitivity towards low histidine concentrations. The SL1344-pGEX sensor, with a high copy number, exhibited remarkable sensitivity and selectivity to histidine in the range of 0 to 50 μM. Notably, even a minute addition of histidine (approximately 2.5 μM) to the M9 medium led to observable fluorescence reduction, rendering it highly suitable for monitoring histidine-deficient cellular environments. This bacterial fluorescence sensor holds great potential for detecting changes in intracellular histidine concentrations during pathogenic bacterial infections and for assessing the impact of drugs on cellular metabolism.

Heavy metal contaminants have serious consequences for the environment and human health. Consequently, effective methods for detecting their presence, particularly in water and food, are urgently required. Accordingly, the present study proposes a sensor for the detection of mercury Hg(II) and lead Pb(II) ions using graphene oxide (GO) as a quenching agent and aptamer solu-tion as a reagent. In the proposed device, the aptamer sequences are labeled by FAM and HEX fluorescent dyes, respectively, and are mixed with 500 ppm GO solution in a microfluidic device. The presence of Hg(II) and Pb(II) ions is then detected by measuring the change in the fluores-cence intensity of the GO/aptamer suspension as the aptamer molecules undergo fluorescence resonance energy transfer (FRET). The experimental results show that the aptamer sensors have a linear range of 10~250 nM (i.e., 2.0~50 ppb) for Hg(II) ions and 10~100 nM (i.e., 2.1~20.7 ppb) for Pb(II) ions. Furthermore, the limit of detection is around 2 ppb for both metals, which is signifi-cantly lower than the maximum limits of 6 ppb and 10 ppb prescribed by the World Health Or-ganization (WHO) for Hg(II) and Pb(II) in drinking water, respectively.

In recent studies it has been shown that fluorescence lifetime imaging (FLIM) may reveal intracellular structural details in unstained cytological preparations which are not revealed by standard staining procedures. The aim of this investigation was to show whether FLIM images could reveal areas suggestive of polymerization in red blood cells (RBCs) of sickle cell disease (SCD) patients. We examined air-dried unstained blood films using auto-fluorescence FLIM images of 45 SCD patients and compared the results with those of 27 control persons without hematological disease. All control RBCs revealed homogeneous cytoplasm without any foci. Rounded non-sickled RBCs in SCD showed between zero and three small intensively fluorescent dots with higher lifetime values. In sickled RBCs we found additionally larger irregularly shaped intensively fluorescent areas with increased FLIM values. These areas were interpreted as equivalent to polymerized hemoglobin. The rounded non-sickled RBCs of SCD patients with homogeneous cytoplasm were not different from those of erythrocytes of control patients in light microscopy. Yet, variables from the local binary pattern transformed matrix of the FLIM values per pixel, showed significant differences between non-sickled RBCs and those of control cells. In a linear discriminant analysis, using local binary pattern transformed texture features (mean and entropy) of the erythrocyte cytoplasm of normal appearing cells, the final model could distinguish between SCD patients and control persons with an accuracy of 84.7% of the patients.

Photosynthesis is one the most important biological processes on earth, producing life-giving oxygen and is the basis for a large variety of plant products. Measurable properties of photosynthesis provide information about its biophysical state and, in turn, the physiological conditions of a photoautotrophic organism. For instance, chlorophyll fluorescence of an intact photosystem is not linear as in the case of a single fluorescent dye in solution, but shows temporal changes related to the quantum yield of the photosystem. Commercial photosystem analyzers already use the fluorescence kinetics characteristics of photosystems to infer the viability of organisms under investigation. Here, we provide a novel approach based on an optical Fabry-Pérot microcavity or that enables the readout of photosynthetic properties and activity for an individual cyanobacterium. This approach offers a completely new dimension of information, which would normally be lost due to averaging in ensemble measurements obtained from a large population of bacteria.

A surgical microscope is large in size, which makes it impossible to be portable. The distance between the surgical microscope and the observation tissue is 15–30 cm, and the adjustment range of the right and left of the camera is a maximum of 30°. Therefore, the surgical microscope is generated attenuation (above 58%) of irradiation optical source owing to the long working distance. Moreover, the observation of tissue is affected because of dazzling by ambient light as the optical source power is strong (55 to 160 mW/cm2). Further, observation blind spot phenomena will occur due to the limitations in adjusting the right and left of the camera. Therefore, it is difficult to clearly observe the tumor. In this study, a compact pen-type probe with a portable surgical microscope is presented. The proposed surgical microscope comprises a small and portable pen-type probe that can adjust the working distance between the probe and the observed tissue. In addition, it allows the adjustment of the viewing angle and fluorescence brightness. The proposed probe has no blind spots or optical density loss.

A surgical microscope is large in size, making portability impossible. The distance between the surgical microscope and the observation tissue is 15 to 30 cm, while the maximum adjustment range of the camera to the right and left is 30°. Therefore, surgical microscopes cause attenuation (above 58%) of the irradiation optical source owing to the long working distance. Moreover, the observation of tissue was dazzled with ambient light because the optical power source was strong (50 to 160 mW/cm2). Owing to the limited ability to adjust the camera to the right and left, a blind spot occurs with a surgical microscope. Therefore, it is difficult to clearly observe a tumor. In this study, a compact pen-type probe with a portable surgical microscope is proposed. The pen-type probe is small with a portable shape, and is capable of adjusting the working distance between itself and the observed tissue. It is also possible to adjust the viewing angle and fluorescence brightness. The proposed pen-type probe has no blind spots or optical density loss.

Even with 100% certainty of a complete cure for breast cancer (BC), there is still a long way to go toward more efficient treatment. This requires sensitive and timely detection and accurate pre/post-clinical characterizations. Despite the availability of advanced diagnostic tools, many cancer patients lack access to efficient diagnostics that are both highly reliable and affordable. The fluorescence-based optical technique aims to make another significant leap forward in improving patient safety. It offers a convenient operation that reduces healthcare costs compared to visual examination tools (VETs). The primary and metastatic stages of BC consider different cancerous cell lines (MDAs), meaning the highest number of cells in this research (up to 300,000) represents the metastatic stages of BC, and 50,000 represents the primary level of BC developments have been studied based on fluorescence-enhanced photodynamic characterizations. The ability to characterize the fluorescence caused by MDA with 50,000 cells compared to the dominant radiation of MDA with 300,000 cells is emphatic proof of the high potential of fluorescence technique in timely BC detections, specifically before it spreads to the axillary lymph nodes. The specific cell numbers of 50,000 and 300,000 were chosen arbitrarily based on the cultivation of common biological limitations. Comparing the outcomes between 50,000 and 300,000 cells allows for evaluating the fluorescence technique’s diagnostic capability across various stages of breast cancer. This assessment provides valuable insights into the effectiveness of the fluorescence-based characterizing approach in detecting cancerous cells at different stages of the disease. Here, we have assessed fluorescence’s spectral shift and intensity difference as a diagnostic approach to distinguish between cancerous and normal breast cells. This study also presents a two-way structure of the 5-aminolevulinic acid (5-ALA) prodrug and Fluorescein Sodium (FS) effect in BC cell characterization from the perspective of photodynamical procedures and the detection side. 5-ALA induces an accumulation of protoporphyrin IX (PpIX) photosensitizer through a biosynthetic pathway, leading to red radiation of fluorescence measurements depending on different factors, such as temperature, incubation time, added glucose of the culturing medium, as well as photosynthesis processes. The presence and progression of breast cancer can be indicated by elevated levels of Reactive Oxygen Species (ROS), which are associated with the production of PpIX in cells following the administration of 5-ALA. Also, nicotinamide adenine dinucleotide (NADH) and flavin adenine dinucleotide (FAD) fluorophores are recognized as the main factors for fluorescence emissions at around 420-580 nm emission intervals. Considering the MDA’s high metastatic potential, the impact of 5-ALA on MDA’s cellular morphology and viability has been investigated. The molecular fluorophores are the primary probes to MDA’s cellular photodynamic considerations, allowing this widespread pre/post-clinical approach. The fluorescence signal reduction due to decreased cell viability and increased MDA’s cellular death rate after 24 hours of the 5-ALA-induced staining corresponds to the changes in lipid metabolism enzymes of MDAs cultured at different doses, which could be known as a cell death inducer function. Furthermore, statistical concerns have been studied using PCA multivariate component analysis to differentiate MDA cell lines administrated by 5-ALA.

Advanced glycation end products (AGEs) play a significant role in the aging processes, further regarding as a hallmark of aging. Despite the importance, a lack of monitoring tools has hampered the study of relationship between AGEs and aging. Here, we firstly report a novel AGEs-selective probe, AGO. AGO presented its ability to detect AGEs more sensitively than a conventional approach of measuring autofluorescence from AGEs. In addition, we confirmed that AGO can detect AGEs depending on kinetics, reflecting by a preference to ribose-derived AGEs. Finally, AGO revealed its competence to visualize glycation products in glycation mimicking model, made by collagen framework. We believe that this study will enrich molecular toolboxes to understand physiological processes of AGEs during aging processes.

Objective: Surgical eradication of malignant glioma cells is theoretically impossible. Therefore, reducing the number of remaining tumor cells around the brain-tumor interface (BTI) is crucial for achieving satisfactory clinical results. The usefulness of fluorescence-guided resection for the treatment of malignant glioma was recently reported, but the detection of infiltrating tumor cells in the BTI using a surgical microscope is not realistic. Therefore, we developed an intraoperative rapid fluorescence cytology system, and evaluated its clinical feasibility for the management of malignant glioma. Materials and methods: Twenty-five selected patients with malignant glioma (newly diagnosed: 17; recurrent: 8) underwent surgical resection under photodiagnosis using photosensitizer Talaporfin sodium and a semiconductor laser. Intraoperatively, a crush smear preparation was made from a tiny amount of tumor tissue, and the fluorescence emitted upon 620/660 nm excitation was evaluated rapidly using a compact fluorescence microscope in the operating theater. Results: Fluorescence intensities of tumor tissues measured using a surgical microscope correlated with the tumor cell densities of tissues evaluated by measuring the red fluorescence emitted from the cytoplasm of tumor cells using a fluorescence microscope. A “weak fluorescence” indicated a reduction in the tumor cell density, whereas “no fluorescence” did not indicate the complete eradication of the tumor cells, but indicated that few tumor cells were emitting fluorescence.Conclusion: The rapid intraoperative detection of fluorescence from glioma cells using a compact fluorescence microscope was a useful to evaluate the presence of tumor cells in the resection cavity walls, and provides surgical implications for the more complete resection of malignant gliomas.

Fluorescein anisotropy, which is a widely used technique to study the folding state of proteins or affinity of ligands, is used in the present work to study the temperature sensing of fluid in a microchannel, by adding fluorophore in the fluid. Fluorescein was used as a temperature probe, while glycerol-aq. ammonia was used as a working fluid. Fluorescence anisotropy of fluorescein were measured by varying various parameters. Apart from this, a comparison of fluorescence anisotropy and fluorescence intensity is also performed.

Fluorophore molecules can be monitored by fluorescence spectroscopy and microscopy which are highly useful and widely used techniques in cell biology, biochemistry and medicine (e.g., biomarker analysis, immunoassays, cancer diagnosis). Several fluorescent micro- and nanoparticle systems based on block copolymer micelles and cross-linked polymer networks, quantum dots, -conjugated polymers, and dendrimers have been evaluated as optical imaging systems. In this review, we highlight recent advances in the construction of fluorescent single-chain nanoparticles (SCNPs) which are valuable artificial soft nano-objects with tunable, small size (as small as 3 nm). In particular, the main methods currently available to endow SCNPs with fluorescent properties are discussed in detail, showing illustrative examples.

Apurinic/apyrimidinic endonuclease 1 (APE1), also known as redox factor-1 (Ref-1), is a multifunctional protein which is widely existing in living organisms. It can specifically recognize and cleave the DNA in apurinic/apyrimidinic (AP) site in the base excision repair (BER) pathway, as well as regulate the expression of genes to activate some transcription factors. The abnormal ex-pression and disruptions in the biological functions of APE1 are linked to a number of diseases, including inflammation, immunodeficiency, and cancer. Hence, it is extremely desired to monitor the activity of APE1, acquiring a thorough understanding of the healing process of damaged DNA and making clinical diagnoses. Thanks to the advent of DNA nanotechnology, some nanodevices are used to image the activity of APE1 with great sensitivity and simplicity. In this review, we will summarize DNA nanotechnology-empowered fluorescence imaging in the past years for APE1 activity according to the types of DNA probe, which are classified into linear DNA probes, composite DNA nanomaterials and three-dimensional (3D) DNA nanostructures. We also highlight the future research directions in the field of APE1 activity imaging.

The importance of detecting bacteria in various food products is ever-increasing, due to recent food trends that lend themselves to food contamination. Additionally, the detection of probiotics in food products is of increasing importance to consumers, who realize the benefits of probiotics on one’s diet. Existing technologies for detection of bacteria in food are accurate, but most are slow, increasingly costly and unsuitable for applications outside of research laboratories. Optic approaches have recently emerged as an alternative, allowing rapid detection of bacterial presence. This study employs a portable kinetics fluorometer, fabricated in-house, in conjunction with NADH sensitive fluorescence reporter for analysis of various food products. The presence of bacteria is detected in 5 minutes. Both pathogenic and probiotic bacteria were detected in food products, such as raw chicken and beef, spoiled lettuce and contaminated water, yogurt, and kombucha tea. The cellular activity of two probiotic pills was also verified. All samples displayed varying levels of bacterial activity. The study indicates the viability of biosensors being used as an alternate method to detect bacteria in food products – and the viability of a fluorescence-based biosensor to detect viable bacteria. The approach is suitable for both laboratory and field determinations.

Berberine (BBR), as a natural isoquinoline alkaloid, has been demonstrated various pharmacological activities, and widely applied in the treatment of diseases. The quantitative analysis of BBR is important for its pharmacological researches and clinical applications. In the work, utilizing the specific interaction between BBR and triplex DNA, a sensitive and selective fluorescent detecting method was established with DNA-templated silver nanoclusters (DNA-AgNCs). After binding with the triplex structure in the template of DNA-AgNCs, BBR quenched the fluorescence of DNA-AgNCs and formed BBR-triplex complex with yellow-green fluorescence. The ratiometric fluorescence signal showed a linear relationship with BBR concentration in a range between 10 nM to 1000 nM, with a detect limit of 10 nM. Our method exhibited excellent sensitivity and selectivity, and it was further applied in BBR detection in real samples.

Medium polarity plays a crucial role in charge-transfer processes and electrochemistry. The added supporting electrolyte in electrochemical setups, essential for attaining the needed electrical conductivity, sets challenges for estimating medium polarity. Herein, we resort to Lippert–Mataga–Ooshika (LMO) formalism for estimating the Onsager polarity of electrolyte organic solutions pertinent to electrochemical analysis. An amine derivative of 1,8-naphthalimide proves to be an appropriate photoprobe for LMO analysis. An increase in electrolyte concentration enhances the polarity of the solutions. This effect becomes especially pronounced for low-polarity solvents. Measured refractive indexes provide a means for converting Onsager to Born polarity, which is essential for analyzing medium effects on electrochemical trends. This study demonstrates a robust optical means, encompassing steady-state spectroscopy and refractometry, for characterizing solution properties important for charge-transfer science and electrochemistry.

Fluorescence microscopy provides an unparalleled tool for imaging biological samples. However, producing high-quality volumetric images quickly and without excessive complexity remains a challenge. Here, we demonstrate a simple multi-camera structured illumination microscope (SIM) capable of simultaneously imaging multiple focal planes, allowing for the capture of 3D fluorescent images without any axial movement of the sample. This simple setup allows for the acquisition of many different 3D imaging modes, including 3D time lapses, high-axial-resolution 3D images, and large 3D mosaics.

Super-Resolution Microscopy enables non-invasive, molecule-specific imaging of the internal structure and dynamics of cells with sub-diffraction limit spatial resolution. One of its major limitations is the requirement for high-intensity illumination, generating considerable cellular phototoxicity. This factor considerably limits the capacity for live-cell observations, particularly for extended periods of time. Here, we overview new developments in hardware, software and probe chemistry aiming to reduce phototoxicity. Additionally, we discuss how the choice of biological model and sample environment impacts the capacity for live-cell observations.

Development of biomarkers of analytes with interest in clinic is an important field of study. In this work, we synthesized and analyzed the new fluorescent acetate-biomarker, Iso-PG. The mechanism of detection is the acetate buffer mediated proton transfer reaction. The rate constants involved were obtained, and we measured the change in the fluorescence lifetime produced as a consequence of the presence of acetate in the medium. Finally, we checked its potential use as acetate biomarker in synthetic serum

Photodynamic therapy (PDT) of cancer is dependent on three primary components: photosensitizer (PS), light, and oxygen. Because these components are interdependent and vary during the dynamic process of PDT, assessing PDT efficacy may not be trivial. Therefore, it has become necessary to develop pre-treatment planning, on-line monitoring and dosimetry strategies during PDT, which become more critical for two or more chromophore systems, e.g. PS-CD conjugates developed in our laboratory for fluorescence-imaging and PDT of cancer. In this study, we observed a significant impact of variable light dosimetry; (i) high light fluence and fluence rate (light dose: 135 J/cm², fluence rate: 75 mW/cm²) and (ii) low light fluence and fluence rate (128 J/cm² and 14 mW/cm² and 128 J/cm² and 7 mW/cm²) in photobleaching of the individual chromophores and their long-term tumor response. The fluorescence at the near-infrared (NIR) region of the PS-NIR fluorophore conjugate was assessed intermittently via fluorescence imaging. The loss of fluorescence, photobleaching, caused by singlet oxygen from the PS was mapped continuously during PDT. The tumor responses (BALB/c mice bearing Colon26 tumors) were assessed after PDT by measuring tumor sizes daily. Our results showed distinctive photobleaching kinetics rates between the PS and CD. Interestingly, compared to higher light fluence, the tumors exposed at low light fluence showed reduced photobleaching and enhanced long-term PDT efficacy. The presence of NIR fluorophore in PS-CD conjugates provides an opportunity of fluorescence imaging and monitoring the photobleaching rate of the CD moiety for large and deeply seated tumors and assessing PDT tumor response in real-time.

Harmful algal blooms are a serious problem for humanity, so the development of tools and methods for their timely detection is an urgent task. The use of optical methods often allows scientists to solve problems of remote and automated monitoring. Temperature spectra of fluorescence can be used as distinctive features of algae, and the fluorescence parameters obtained from them can be used for identification. The paper presents a description of the fluorescence parameters of Alexandrium catenella, and shows their stability during cumulative cultivation. In addition, the cytometric properties of the culture and its pigment composition were studied. In addition, the article compares all the studied properties of this microalga with the alga Prorocentrum cordatum. We demonstrated clear differences in their fluorescence parameters, which makes it possible to distinguish these microalgae by optical methods, for example, during their dominant blooms.

Microplastics (MPs), typically defined as plastic fragments smaller than 5mm, are pervasive in terrestrial and marine ecosystems. There is a need for rapid, portable, low-cost detection systems to assess health and environmental risks. Fluorescent tagging with Nile Red (NR) has emerged as a popular detection method, but variations in fluorescent emissions based on NR solvent, plastic polymer, excitation wavelength, and additives complicate standardization. In this study, seven plastic samples stained with acetone-based NR were analyzed using a fluorescent spectrometer to identify optimal emission peaks across UV-Vis excitation wavelengths. These findings aid in selecting appropriate excitation wavelengths and optical filters for future detection systems. Additionally, a straightforward polymer identification scheme was validated against field-collected plastic samples, whose material composition was confirmed via Fourier Transform Infrared Spectroscopy. This work contributes towards developing accessible microplastic detection technologies by characterizing the fluorescent properties of NR-stained plastics and enhancing the capability for effective environmental monitoring. Future research will expand the dataset to include diverse plastics with varying additives and weathering, and incorporate computer-vision tools for automated data processing and polymer identification.

Microgreens (young, edible plantlets) are a remarkable opportunity for both consumers, to benefit from health promoting compounds and for applied research, as such organisms have a very high plasticity related to environmental cues, allowing biotechnology development with low costs. Ocimum basilicum species naturally synthesize valuable, phenolic compounds, among which rosmarinic acid is most prominent. Basil plantlets were grown for 10 days under either full spectrum light (white light) or modulated blue:red:far-red:UV spectrum with an additional factorization, by applying fertilisation. Biomass accumulation reached up to 0.8 g/20 plantlets, while chlorophyll fluorescence was in the 0.75 – 0.78 range and remained uniform across treatments, indicating that no significant stress was exerted under modified light treatment. However, total phenolic contents and, in particular, rosmarinic acid contents were markedly enhanced (up to 7.5 mg/g in the red cultivar) under modulated light treatment and fertilization, compared to full spectrum light. Moreover, gene expression was enhanced, 1.3-6.3 fold for genes coding for enzymes involved in phenylpropanoid synthesis patwhays, such as phenylalanine ammonia lyase (PAL), Catechol-O-methyltransferase (COMT) and renin-angiotensin system (RAS). Overall, light modulation coupled with fertilization led to the production of basil microgreens with up to 10% more total phenolics and up to 25% more rosmarinic acid.

The aim of this work was to describe the physiological limitations induced under drought conditions in young sweet orange trees, including the crop capability to recuperate its physiological status once re-watering, and after a water withholding. The trial was conducted during two consecutive months (July and August) in two-years old sweet orange trees. Three irrigation treatments were arranged: A full irrigation treatment; (FI); a low-frequency deficit-irrigation treatment (LFDI); and a sustained-deficit irrigation (SDI) treatment. The obtained results showed that for Stem values below -1.5 MPa, significant decreases in gas exchange rates, evidencing diffusive limitations to drought stress. Additionally, there was evidence of increased osmolyte synthesis, compatible as a defensive response to prevent oxidative damage. Likewise, the isohydric behaviour observed also resulted in significant decreases in gs even for moderate stress situations. In addition, it was observed that in the LFDI treatment, the stress levels reached caused a significant increase in the levels of Pro and MDA, which were not equal to those detected in FI during the recovery periods, which leads us to assume that potential values below -1.8 MPa would be causing significant oxidative damage with no capacity for subsequent recovery, and probably affecting the final yield.

Revealing the binding properties of calcium ion (Ca2+) and magnesium ion (Mg2+) to chromophoric dissolved organic matter (CDOM) facilities understanding the effect of natural water composition on the photophysics of dissolved organic matter. Steady-state and time-resolved fluorescence spectrometry, and dynamic light scattering were applied to investigate the fluorescence quenching process of CODM by Ca2+ and Mg2+. The binding of Ca2+ and Mg2+ preferred terrestrial CDOM to aquatic CDOM. The fluorescence quenching of CDOM by cations mainly occurred in a static process, which was based on the fact that the decrease of steady-state fluorescence intensity was greater than fluorescence lifetime. The fluorescence quenching was profound under longer excitation and emission wavelength. The binding constant (K, L/mol) for Ca2+ to CDOM from terrestrial source ranged from 4.29 to 5.09 (lgK), which was approximately one order of magnitude higher than that of Mg2+ to CDOM (3.86 to 4.56). Fluorescence decay became faster in the presence of Ca2+ and Mg2+. Lifetime distribution of CDOM excited states shifted to small value side in the presence of metal ions, particularly for Ca2+, indicating fluorescence quenching of CDOM mainly through the interaction of Ca2+/Mg2+ with relatively long-lived fluorophores.

Single particle tracking (SPT) is a powerful class of methods for studying the dynamics of biomolecules inside living cells. The techniques reveal the trajectories of individual particles, with a resolution well below the diffraction limit of light, and from them the parameters defining the motion model, such as diffusion coefficients and confinement lengths. Most existing algorithms assume these parameters are constant throughout an experiment. However, it has been demonstrated that they often vary with time as the tracked particles move through different regions in the cell or as conditions inside the cell change in response to stimuli. In this work, we propose an estimation algorithm to determine time-varying parameters of systems that discretely switch between different linear models of motion with Gaussian noise statistics, covering dynamics such as diffusion, directed motion, and Ornstein-Uhlenbeck dynamics. Our algorithm consists of three stages. In the first stage, we use a sliding window approach, combined with Expectation Maximization (EM) to determine maximum likelihood estimates of the parameters as a function of time. These results are only used to roughly estimate the number of model switches that occur in the data to guide the selection of algorithm parameters in the second stage. In the second stage, we use change detection (CD) techniques to identify where the models switch, taking advantage of the off-line nature of the analysis of SPT data to create non-causal algorithms with better precision than a purely causal approach. Finally, we apply EM to each set of data between the change points to determine final parameter estimates. We demonstrate our approach using experimental data generated in the lab under controlled conditions.

The effects of simulated acid rain (SAR) on the photosynthetic performance of subtropical coniferous species have not been thoroughly investigated. In this study, we treated two coniferous species, Pinus massoniana (PM) and Cunninghamia lanceolata (CL), with SAR and then analyzed photosynthetic activities via the simultaneous measurement of prompt fluorescence(PF), delayed fluorescence(DF), and modulated reflection at 820 nm(MR820). Following the low-pH SAR treatment, the I–P phase of the OJIP curves of PM and CL decreased significantly and then the K-band and L-band were detectable. The delayed fluorescence for both PM and CL decreased as the pH of the SAR solution decreased, with a more significant decrease in the I1 peak than in the I2 peak. According to the MR820 curve, the exposure to SAR stress inhibited the rapid decrease and slow increase in the MR820 transients of PM and CL. The gradients of the decreasing and increasing phases were lower for CL than for PM at pH 2.5. In addition, SAR decreased the light energy captured per unit area (ABS/CSm) and the quantum yield of electron transfer per unit area (ETO/CSm), but it increased the accumulation of QA−, thereby decreasing primary photochemical efficiency (TRO/CSm, φPO). These changes in photosystem II (PSII) resulted in a decrease in the maximum quantum yield of PSII (Fv/Fm) and the performance index (PIABS). Moreover, PSII was protected from thylakoid membrane photodamages through the increase in heat dissipation per unit area (DIO/CSm) in response to SAR. The increase in δRO as the pH of the SAR solution decreased was observed for PM, but not for CL. Considered together, the study findings suggest that SAR treatments can decrease chlorophyll contents and damage the OEC in PM and CL, which obstructs the transfer of electrons on the donor and acceptor sides of PSII. However, PM is better able to withstand SAR stress than CL, likely because of the activation of a protective mechanism (reflected by the change in δRO). Therefore, in coniferous forest areas severely affected by acid rain, CL may need to be protected more than PM.

Multiphoton microscopy (MPM) is a cutting-edge nonlinear microscopy technique known for its exceptional capabilities in imaging dense tissues, making it an ideal tool for exploring human kidney tissue. This study delves into the application of MPM in evaluating renal cell tumors and characterizing tumor capsules. MPM encompasses two core methods: two-photon excitation fluorescence (TPEF) and second harmonic generation (SHG). It leverages femtosecond lasers to provide deep tissue imaging while minimizing phototoxicity, making it well-suited for live tissue analysis. The study analyzed 100 formalin-fixed paraffin-embedded (FFPE) kidney tissue samples, ensuring compliance with ethical standards. Using a Ti:Sapphire laser for femtosecond pulses and a variety of optical components and filters, the researchers captured TPEF and SHG signals, facilitating image analysis. Normal kidney tissue exhibited distinctive structures like glomeruli and tubules under MPM. Renal cell carcinoma (ccRCC) displayed unique TPEF patterns with eccentrically located nuclei and indistinct cytoplasmic membranes. Papillary RCC (pRCC) exhibited a papillary pattern with dark nuclei, while chromophobe RCC (chRCC) showcased distinct features like thick cell membranes, strong TPEF signal in nuclei, and granular cytoplasm. Renal oncocytoma (RO) presented strong TPEF signals in cuboidal cells with microcyst-like arrangements. Overall, MPM proved invaluable in assessing human kidney tissue, offering distinct TPEF patterns for different renal cell tumor types. This non-invasive technique has the potential to enhance pathological examinations and advance our understanding of complex biological processes, ultimately contributing to improved diagnostics and treatment strategies for renal diseases.

The biophysical consequences of nanoscale curvature have been challenging to resolve due to size-dependent membrane behavior and the experimental resolution limits imposed by optical diffraction. Recent advances in nanoengineering and super-resolution techniques have enabled new capabilities for creating and observing curvature. In particular, draping supported lipid bilayers over lithographically patterned substrates provides a model system for endocytic pits. The experiments and simulations presented below describe the possible detection of membrane curvature through fluorescence recovery after photobleaching (FRAP), fluorescence correlation spectroscopy (FCS), single particle tracking (SPT), and polarized localization microscopy (PLM). FRAP and FCS depend on diffraction-limited illumination and detection. In particular, a simulation of FRAP shows no effects on lipids diffusion due to a 50 nm diameter membrane bud at any stage in the budding process. Simulated FCS demonstrated small effects due to a 50 nm radius membrane bud that was amplified with curvature-dependent lipid mobility changes. However, PLM and SPT achieve sub-diffraction-limited resolution of membrane budding and lipid mobility through the identification of the single-lipid positions with ≤15 nm spatial and ≤20 ms temporal resolution. By mapping the single-lipid step lengths to locations on the membrane, the effects of curvature on lipid behavior have been resolved.

Chylothorax is a rare complication occurring after cardio-thoracic surgical procedures. This condition presents challenges about diagnosis and treatment. Operative ductal ligation is the method of choice for relapsing or refractory cases, and it can be performed through the aid of IGC injection for the identification of chylous leakage. Our report presents the use of ICG fluorescence during VATS to successfully identify and treat a left-sided post-surgical chylothorax. The patient underwent a pulmonary wedge resection for a suspect malignant lesion and developed chylous leakage in the early postoperative period. On postoperative day 7 the patient underwent a revision thoracoscopy for hemostasis and thoracic duct ligation. ICG injections have been performed through bilateral inguinal lymph nodes and approximately 15 minutes after we performed the re-thoracoscopy with effective identification and ligation of the chyle leakage. ICG fluorescence-guided VATS is a valuable and effective method for managing postoperative chylothorax, especially for left-sided leaks. The video of the procedure can be found at: https://zenodo.org/records/13786288

The emergence of "green" materials has been attracting significant attention along the last few years for various applications. Here, we report a rapid, efficient and reproducible microwave-assisted synthesis of graphene quantum dots GQDs of identical features whatever the nature of biomass wastes investigated. The synthesized GQDs were fully characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, transmission electron microscopy and dynamic light scattering. The nanoparticles display narrow size of some nanometers with crystal lattices. Furthermore, the water-soluble particles show excitation-dependent photoluminescence ranging from blue to orange emission wavelength in solution. Interestingly, thin films display white light emission under 325 nm UV-light excitation, while aggregation-induced quenching is usually observed.

To evaluate dryland wheat genotypes' performance to different pre-crop and residue management under dryland conditions, a split-split plot experiment based on RCB design with three replications was conducted for two years (2017-2018 and 2018-2019). The site of study's long-term average precipitation, temperature, and relative humidity are 376 mm, 9 ◦C, and 50%, respectively. Wheat-wheat and vetch-wheat cropping systems were considered in the main plots, different wheat and vetch residue levels including 0, 2, and 4 t ha-1 were located in subplots, and five dryland wheat genotypes including Sadra, Hashtroud, Baran, Varan, and Ohadi were allocated in sub-sub plots. Results indicated that leaf chlorophyll content index (CCI) and stomatal conductance (gs) were greater in the vetch-wheat cropping system compared to the wheat monoculture system for all genotypes. Normalized differences vegetative index (NDVI) of genotypes improved by applying the crop residue. Over two years, the application of crop residues resulted in higher variable fluorescence at J and I steps as well as an increase in the photosynthesis performance index (PI). Varan and Baran genotypes stood out as the superior genotype, exhibiting the highest values physiological characteristics and grain yield under the application of 4 t ha-1 of vetch residue. Grain filling rate (GFR) was reduced, while grain filling duration (GFD) was increased with increasing the crop residue levels. The enhanced grain yield of wheat genotypes grown under vetch residue attributed to the factors such as improvement in leave pigments and photosynthetic efficiency which facilitate longer grain filling duration with high grain weight. As a result, it is advisable to adopt a vetch-wheat cropping system with a high proportion of crop residue in dryland regions to achieve increased and sustainable wheat production.

For very first time, we report the synthesis of 8-(2-methoxyphenyl)-6-methyl-2-(1-methyl-1H-benzo[d]imidazol-2-yl)quinoline 1. This was achieved in several steps, including usage of Suzuki reaction for functionalization of 2-(1H-benzo[d]imidazol-2-yl)quinoline moiety. The new compound exhibits blue fluorescence. Its structure was confirmed with 1D- and 2D-NMR spectroscopy, IR-spectroscopy, high-resolution mass spectrometry and X-ray analysis.

Laser-induced fluorescence spectroscopy (LIFS) is actively used for remote sensing of atmospheric aerosols and currently is one of the most sensitive and selective techniques for determining small concentrations of substances inside particles. The use of high-power femtosecond laser sources for LIFS-based remote sensing of aerosol contributes to the development of new-generation fluorescence atmospheric lidars since it makes it possible overcoming the energy threshold for the nonlinear-optical effects of multiphoton absorption in particles and receiving the emission signal at long distances in the atmosphere. Our study is aimed to the development and experimental demonstration the technique of nonlinear laser-induced fluorescence spectroscopy (NLIFS) based on the remote excitation of aerosol fluorescent emission stimulated by a spatially-structured high-power femtosecond laser pulse. Importantly, for the first time to our knowledge, we demonstrate the advances of using stochastically-structured plasma-free intense light channels (postfilaments) specially formed by propagation of femtosecond laser radiation through a turbulent air layer for improving NLIFS efficiency. A multiple increase in the received signal of two-photon-excited fluorescence of polydisperse dyed aqueous aerosol by the structured postfilaments is reported.

Gold nanohole arrays are periodic metastructures gathering huge interest for biosensing applica-tions. The grating-like structure defines their plasmonic mode features and their angular disper-sion can be used to highlight efficiently their interaction with the fluorescence emission of a properly tuned fluorophore. Resorting to a properly tuned/engineered/optimised plasmonic na-nohole array and a commercial organic dye, we performed an accurate resolved angle-resolved optical characterization. The plasmonic fingerprints was consequently identified as a modification of the dye photoluminescence signal in terms of both spectral redistribution and enhancement. Interestingly, by analyzing the results, an advantageous measurement configuration can be iden-tified to better engineer a suitable platform for efficiency maximization in plasmon-enhanced flu-orescence-based applications. Therefore, the coupling mechanism with the plasmonic modes, and nanostructure properties can be carefully co-optimized.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Within the spectra of lanthanide atoms quite often overlapping spectral lines (blends) are observed. On the example of complicated blend situations within Pr I and La I it is shown that in such cases a combination of optogalvanic and laser-induced fluorescence detection is necessary to find all transitions contributing to the observed spectral signature.

Dibutyl phthalate (DBP) is widely used as a plasticizer in the production of polymeric materials to give them flexibility, strength and extensibility. However, due to its negative impact on human health, in particular, reproductive function and fetal development, the content of DBP must be controlled in food and environmental objects. The present study aims to develop a sensitive, fast and simple polarization fluorescent immunoassay (FPIA) using monoclonal antibodies derived against DBP (MAb-DBP) for its detection in open waters. New conjugates of DBP with various fluorescein derivatives were obtained and characterized: 5-aminomethylfluorescein (AMF) and dichlorotriazinylaminofluorescein (DTAF). The advantages of using the DBP-AMF conjugate in the FPIA method are shown, the kinetics of binding of this drug with antibodies is studied, the analysis is optimized, and the concentration of monoclonal antibodies is selected for sensitive analysis - 16 nM. The calibration dependence of the fluorescence polarization signal for the detection of DBP was obtained. The observed IC50 (40 ng/mL) and LOD (10 ng/mL) values were improved by a factor of 35 for the previously described FPIA using polyclonal antibodies. This technique was tested by the added/found method, the percentage of DBP discovery in water ranged from 85 to 110%. Using the developed method, real water samples from Lake Onega were tested, and a good correlation was shown between the results of the determination of DBP by the FPIA method and GC-MS/MS. Thus, the FPIA method developed in this work can be used to determine DBP in open water reservoirs.

Genetic code expansion has emerged as an enabling tool to provide insight into functions of understudied proteinogenic species such as small proteins and peptides, and to probe protein biophysics in the cellular context. Here we discuss recent technical advances and applications of genetic code expansion in cellular imaging of complex mammalian protein species, along with considerations and challenges upon using the method.

The European heatwave of 2018 led to record-breaking temperatures and extremely dry conditions in many parts of the continent resulting in widespread decrease in agricultural yield, early tree-leaf senescence, and increase in forest fires in Northern Europe. Our study aims to capture the impact of the 2018 European heatwave on terrestrial ecosystem through the lens of a high-resolution solar-induced fluorescence (SIF) data acquired from the Orbiting Carbon Observatory (OCO-2) satellite. SIF is proposed to be a direct proxy for gross primary productivity (GPP) and thus can be used to draw inferences about changes in photosynthetic activity in vegetation due to extreme events. We explore spatial and temporal SIF variation and anomaly during spring and summer months across different vegetation types (agriculture, broadleaved forest, coniferous forest, and mixed forest) during the European heatwave of 2018 and compare it to non-drought conditions (most of Southern Europe). About one-third of Europe’s land area experienced a consecutive spring and summer drought in 2018. Comparing 2018 to mean (2015-2017) conditions, we found a change in intra-spring season SIF dynamics for all vegetation types, with lower SIF during the start of spring followed by an increase in fluorescence from mid-April. Summer, however, showed a significant decrease in SIF. Our results show that particularly agricultural areas were severely affected by the hotter drought of 2018. Furthermore, the intense heat wave in Central Europe showed about 31% decrease in SIF values during July and August as compared to the mean over three previous years. Furthermore, our MODIS and OCO-2 comparative results indicate that especially for forests, OCO-2 SIF has a quicker response and possible higher sensitivity to drought in comparison to MODIS’s fPAR and NDVI when considering shorter reference periods, which highlights the added value of remotely sensed solar-induced fluorescence for studying the impact of drought on vegetation.

The interaction between single or a fixed number of photons with a single absorber is of fundamental interest in quantum technology. The harnessing of light matter interactions at the single particle limit has several potential applications ranging from quantum communication and quantum metrology to quantum imaging. In this letter, a setup for heralded two-photon absorption at the single absorber level is proposed. The setup is based on a heralded two-photon source utilizing spontaneous parametric down-conversion, entanglement swapping and sum frequency generation for joint detection. The feasibility of the scheme is discussed by reviewing recent achievements in utilizing entangled and correlated photons for two-photon absorption as well as single photon absorption experiments at the limit of single absorbers in the context of applications in imaging (here mainly microscopy) and spectroscopy.

The green biomass of horticultural plants contains valuable secondary metabolites (SM) which can potentially be extracted and sold. When exposed to stress, plants accumulate higher amounts of these SMs, making the extraction and commercialization even more attractive. We evaluated the potential for accumulating of the flavones cynaroside and graveobioside A in leaves of two bell pepper cultivars (Mavras and Stayer) when exposed to salt stress (100 mM NaCl), UVA/B excitation (UVA 4-5 W/m²; UVB 10-14 W/m² for 3 hours per day) or a combination of both stressors. HPLC analyses proved the enhanced accumulation of both metabolites under stress conditions. Cynaroside accumulation is effectively triggered by high-UV stress, whereas graveobioside A contents increase under salt stress. Highest contents were observed in plants exposed to combined stress. Effects of stress on overall plant performance differed significantly between treatments, with least negative impact on aboveground biomass found for high-UV stressed plants. The usage of two non-destructive instruments (Dualex and Multiplex) allowed us to gain insights in ontogenetical effects at the leaf level and temporal development of SM contents over time. Indices provided by those devices correlate fairly with amounts detected via HPLC (Cynaroside: R2 = 0.46 – 0.66; Graveobioside A: R2 = 0.51 – 0.71). The concentrations of both metabolites tend to decrease at leaf level during the ontogenetical development even under stress conditions. High-UV stress is a promising tool for enriching plant leaves with valuable SM without major effects on plant biomass. All data is available online [1].

The Upper Jurassic (Oxfordian Age) Smackover Formation is a significant source for hydrocarbon production in southwest Alabama. Brooklyn Field is in southeast Conecuh County, Alabama and has been a major producer of oil and natural gas for the state. The Smackover is a carbonate formation that is divided into seven distinct lithofacies. In southwest Alabama, the Smackover Formation is heavily influenced by paleotopography from the underlying Paleozoic rocks of the Appalachian system. The goal of this study is to determine elemental ratios in rock core within the Smackover Formation using a X-ray fluorescence (XRF) handheld scanner, to correlate between lithofacies in the Smackover Formation and elementally characterize the upper oolitic grainstone reservoir and the lower thrombolite boundstone. Eight wells were used for the study within Brooklyn Field and Little Cedar Creek fields. Cores from the eight wells were scanned on six-inch intervals. Chemical logs were produced to show elemental weights in relation to depth and lithofacies. Well data collected for chemical signatures within producing zones were correlated to reservoir lithofacies and porosity. Aluminum, silicon, calcium, titanium, and iron were the most significant (>95% confidence level) predictors of porosity and is related to the depositional environment and subsequent diageneses of the strata. XRF data suggests relative enrichments in iron, titanium, and potassium may be related to deposition in relatively restricted marine waters.

We report on the effects of the film morphology on the fluorescence spectra for a thin film including a quinoxaline-based co-polymer (TQ1) and a fullerene derivative (PC₇₀BM). The ratio between the polymer and the fullerene derivative, as well as the processing solvent were varied. Beside the main emission peak at 700 nm in the fluorescence spectra of thin films of this phase-separated blend, a broad emission band is observed with a maximum at 520 - 550 nm. The intensity of this emission band decreases with an increasing degree of mixing in the film and becomes most prominent in thicker films, films with high PC₇₀BM content, and films that were spin-coated from solvents with lower PC₇₀BM solubility. We assign this emission band to aggregated PC₇₀BM.

The analysis of particulate matter (PM) in dilute solutions is an important target for environmental, geochemical and biochemical researches. Here we show how the microdrop technology may allow to control, through the evaporation of small droplets, the deposition of insoluble materials dispersed in a solution on a well-defined area with a specific spatial pattern. Using this technology the superficial density of the deposited solute can be accurately controlled. In particular, it becomes possible to deposit an extremely reduced amount of insoluble material -in the order of few μg- on a confined area, thus allowing a relatively high superficial density to be reached within a limited time. In this work we quantitatively compare the microdrop technique for the preparation of particulate matter samples with the classical filtering technique. After having been optimized, the microdrop technique allows to obtain a more homogeneous deposition and limit sample consumption of a factor ~25. This method is potentially suitable for many novel applications in different scientific fields.

The phenomena of light absorption, fluorescence and laser emission are accounted for within a unique picture. The atomic dipole is dealt with in a quantum framework, whereas the electromagnetic field is assumed to be a classical sine-wave. The on and off resonance cases are investigated. This is achieved owing to a novel application of Poynting's theorem. Observable predictions are made, regarding absorption of the electromagnetic energy and the frequency bandwidth of light emitted either by fluorescence or laser effect.

Railway transportation is one of the main modes of long-distance coal transportation, and it is inevitable to cause environmental pollution during the transportation process. In order to improve the environment along the railway and increase the utilization rate of coal resources, this paper proposes a detection algorithm for scattered coal solidification layer during transportation based on the YOLO v8 model, and designs an intelligent recognition model suitable for coal solidification layer detection devices by combining fluorescence detection methods. Through experimental analysis, the model meets the requirements of practical detection and plays a crucial role in environmental protection, with strong practical application value.

Reviewed are recent efforts leading to chemo-enzymatic syntheses of strongly fluorescent ribosides of nucleobase analogs, potentially applicable in analytical biochemistry and cell biology. Described are syntheses and properties of fluorescent purine, 8-azapurine and etheno-purine ribosides, obtained using various types of the purine nucleoside phosphorylase (PNP) as catalysts of ribosylation, and -ribose-1-phosphate (r1P) as a second substrate. In several instances, the ribosylation sites were different than the canonical purine N9. Some of the obtained ribosides show fluorescence yields close to 100%. Their main applications are assays of PNP, nucleoside hydrolases, and other enzyme activities both in vitro and, possibly, within the living cells, using fluorescence microscopy.

X-ray Fluorescence Computed Tomography (XFCT) is an emerging non-invasive imaging technique providing molecular-level data, gaining attention for high-resolution imaging. However, increased sensitivity with benchtop X-ray sources raises radiation exposure. Artificial Intelligence (AI), particularly deep learning (DL), has revolutionized medical imaging by delivering high-quality images in the presence of noise. In XFCT, traditional methods rely on complex algorithms for noise reduction, but AI holds promise in addressing high-dose concerns. We present an optimized SCUNet model for noise reduction in low-concentration XRF images. Compared to higher-dose images, our method’s effectiveness is evaluated. While various denoising techniques exist for X-ray and CT, few address to XFCT. The DL model is trained and assessed using the augmented data, focusing on background noise reduction. Image quality is measured using PSNR and SSIM, comparing outcomes with 100% X-ray dose images. Results show the proposed algorithm achieves high-quality images from low-dose and low-contrast agents, with a maximum PSNR of 39.05 and SSIM of 0.86. The model outperforms BM3D, NLM, DnCNN, and SCUNet in both visual inspection and quantitative analysis, particularly in high-noise scenarios. This indicates the potential of AI, specifically the SCUNet model, in significantly improving XFCT imaging by mitigating the trade-off between sensitivity and radiation exposure.

(1) Background: There is a risk of Aflatoxin B1(AFB1) pollution in yellow rice wine[1],threatening human life and health, the risk is a major focus of government attention and social concern.The current detection technology cannot meet the needs of large-scale testing due to the disadvantages of high false positive, cumbersome operating procedures or high cost.Therefore, it is urgent to study and establish a high-sensitivity and high-fast detection method for AFB1 to provide technical support for yellow rice wine quality supervision and risk assessment.; (2) Methods: In this study, three-factor and three-level orthogonal experiments were carried out for oscillation time, reaction temperature and tomography time to determine the best reaction conditions for pretreatment.AFB1 detection was carried out by aflatoxin time-resolved fluorescence immunochromatography technology，Through the ratio of the T signal value of the detection line to the C signal value of the quality control line and the natural logarithmic value of the standard solution concentration[2], a rapid detection technology of time-resolution fluorescence immunochromatography is established.The technology was methodically assessed, the actual yellow rice wine samples were tested, and the results were compared with the HPLC method; (3) Results: The results show that the optimal reaction conditions for pretreatment are: the sample oscillation time is 20min, the sample reaction temperature is 37°C, and the sample chromatography time is 6min. In the actual sample detection of yellow rice wine, The time-resolved fluorescence immunochromatography detection technology established in this study detects AFB1. The detection limit is 0.3 μg·kg-1,The linear range is 0.8-12.0μg·kg-1,The linear equation of the corresponding standard curve y=-0.1913x+0.5206 (R2=0.9948),The standard deviation is 0.029.The results of the in-batch accuracy and precision of this method show that the addition and recovery rate is 77.9% - 105.7%,The coefficient of variation is in 4.5% - 10.3%; Inter-batch accuracy and precision test results show that the addition recovery rate is75.9% - 85.8%,the coefficient of variation is in 8.1% - 13.9%,explain that the detection technology has good accuracy and precision.Compared with HPLC, the relative error is less than 10%,It shows that aflatoxin time-resolution fluorescence immunochromatography technology is in good agreement with the test results of national standard methods; (4) Conclusions:he rapid detection technology of time-resolution fluorescence immunochromatography of AFB1 in yellow rice wine is easy to operate with fast detection speed, high sensitivity, good repeatability and stability, and has broad application prospects.

Mitochondrial dysfunction has been linked to psoriasis, and may be an important underlying factor contributing to this disease. However, a precise methodology for assessing mitochondrial dysfunction has yet to be developed. One promising approach is to measure NADH autofluorescence from affected skin areas. In this study, we show that Flow Mediated Skin Fluorescence (FMSF) can be used for non-invasive assessment of mitochondrial dysfunction in psoriasis. The fluorescence level at baseline and the half-time of ischemic growth (t1/2) derived from the FMSF traces can be used for non-invasive assessment of NADH/NAD+ redox imbalance in psoriatic lesions compared to unaffected skin. These results are supported by analysis of the key FMSF parameters, Reactive Hyperemia Response (RHR) and Hypoxia Sensitivity (HS). This method not only contributes to understanding of the biochemical processes involved in the etiopathogenesis of psoriasis, but also provides a basis for identifying new drug targets and improving the treatment process.

Herein, we developed a highly sensitive and specific bimolecular fluorescence complementation (BiFC)-based influenza A virus (IAV) sensing system created by combining a galactose/glucose-binding protein (GGBP) with an N-terminal large domain (YN1-172) and a C-terminal small domain (YC173-239) of enhanced yellow fluorescence protein (eYFP). The GGBP-based BiFC reporter exhibits the fluorescence reconstitution as a result of conformational changes in GGBP when lactose, derived from 6’-silalyllactose used as a substrate for neuraminidase (NA), binds to GGBP in the presence of IAV. The system showed a linear dynamic range from 1 x 100 TCID50/mL to 1 x 107 TCID50/mL, with a detection limit of 4 x 101 TCID50/mL for IAV (H1N1), demonstrating ultra-high sensitivity. Our system exhibited fluorescence intensity enhancements in the presence of IAV, while displaying weak fluorescence signals when exposed to NA-deficient viruses such as RSV A, RSV B, adenovirus and rhinovirus, thereby indicating selective responses for IAV detection. Taken together, our system provides a simple, highly sensitive and specific IAV detection platform based on BiFC capable of detecting the ligand-induced protein conformational changes, obviating the need for virus culture or RNA extraction processes.

The luminescent properties of photocured aliphatic and aromatic network polycarbonate methacrylates containing organic fluorescent dyad have been studied. The dyad molecule includes two photosensitive fragments – tetraarylimidazole with a hydroxy group and azomethinocoumarin, in each of which excited state intramolecular proton transfer occurs, which leads to the appearance of two emissions - blue and green. It was established that the ratio of the intensities of these emissions depends on the excitation wavelength, as well as on the length, flexibility and polarity of the matrix oligomeric bridges.

N,N-dimethyl-4-nitroaniline (NNDM4NA, C8H10O2N2), is a superelastic and superplastic charge-transfer molecular crystal with a high molecular dipole moment, µ=7.95 D, which crystal-lizes in the acentric polar point group 2. Highly aligned poly-l-lactic acid (PLLA) polymer micro-fibers with embedded NNDM4NA nanocrystals were fabricated using the electrospinning tech-nique. The composite fibers display an extraordinarily high piezoelectric output response, where for a small stress of 5.0x103 Nm-2, an effective piezoelectric voltage coefficient of geff=3.6 VmN-1 was obtained. The fibers were found to display solid state blue fluorescence with a long (147 ns) life-time decay. Furthermore, the composite fibers exhibit an average increase of 67% on the Young modulus reaching 55 MPa, while the tensile strength reaches 2.8 MPa when compared with solely PLLA fibers. The results show that nanocrystals, from small organic molecules, with elastic and piezoelectric properties form hybrid functional 2-dimensional luminescent array which are me-chanical strong and generate high output voltages making them promising for applications in energy harvesting and as solid-state blue emitters.

Carbon dots (C-dots) represent an emerging class of non-toxic nano-emitters that show excitation wavelength dependent photoluminescence (PL) with high quantum yield (QY) and minimal photobleaching. The vast majority of studies focus on C-dots that exhibit the strongest PL emission in the blue/green region of the spectrum, while longer wavelength emissions are ideal for applications such as bioimaging, photothermal and photodynamic therapy and light emitting diodes. Effective strategies to modulate the PL emission of C-dot based systems towards the red end of the spectrum rely on extensive conjugation of sp2 domains, heteroatom doping, solvatochromism, surface functionalization and passivation. Those approaches are systematically presented in this review, while emphasis is given on important applications of red-emissive suspensions, nanopowders and polymer nanocomposites.

The low relative humidity (RH) levels in a greenhouse during the daytime in a strawberry (Fragaria × ananassa Duch) cultivation period negatively affect the growth of strawberry related to photo-physiology. Therefore, this study was conducted to confirm an efficient RH management method by analyzing the phenotypic characteristics related to photo-physiology by controlling the RH in a greenhouse during the daytime with a fog system. Strawberry plants were grown respectively in a greenhouse affected by natural RH changes (control) and in a greenhouse with 40% ~ 50% RH adjusted during the daytime using a fog system. In the greenhouse, with controlled RH, the temperature decreased, and the RH was higher in the initial growth stage of strawberry planting than the control. It was observed a significant increase in the survival rate of the strawberry plant, as well as the incidence of powdery mildew, was lowered. In addition, the photosynthetic rate and OJIP chlorophyll a fluorescence transients related to photosystem II efficiency of strawberry leaves were significantly higher in the fog treatment than in the control. In winter, during the day, the number of days on which the temperature dropped below 20℃ has increased, the greenhouse temperature with controlled RH was lower due to the fog system. When the yield per strawberry plant in January and February was investigated, the control was higher than the RH treatment. Therefore, RH management using a fog system must be controlled at a level where a temperature range is adequate for plant growth, in which the efficient control of these parameters increases strawberry productivity.

Rising temperature is among the most remarkably stressful phenomena induced by global climate changes with negative impacts on crop productivity and quality. It has been previously shown that volatiles belonging to the isoprenoid family can confer protection against abiotic stresses. In this work, two Vitis vinifera cv. ‘Chardonnay’ clones (SMA130 and INRA809) differing for a mutation of the DXS gene encoding for 1-deoxy-D-xylulose-5-phosphate (the first dedicated enzyme of the 2C-methyl-D-erythritol-4-phosphate (MEP) pathway) and involved in the regulation of isoprenoids biosynthesis were investigated in field trials and laboratory experiments. Leaf monoterpene emission, chlorophyll fluorescence and gas-exchange measurements were assessed over three seasons at different phenological stages and either carried out in vivo or controlled conditions under contrasting temperatures. A significant (p<0.001) increase in leaf monoterpene emission was observed in INRA809 when plants were experiencing high temperatures and over two experiments while no differences were recorded for SMA130. Significant variation was observed for the rate of leaf CO2 assimilation under heat stress, with INRA809 maintaining higher photosynthetic rates and stomatal conductance values than SMA130 (p=0.003) when leaf temperature increased above 30°C. At the same time, maximum photochemical quantum yield of PSII (Fv/Fm) was affected by heat stress in the non-emitting clone (SMA130), while the INRA809 showed a significant resilience of PSII under elevated temperature conditions. Consistent data were recorded between field seasons and temperature treatments in controlled environment conditions suggesting a strong influence of monoterpene emission on heat tolerance under elevated temperatures. This work provides further insights on the photoprotective role of isoprenoids under high temperatures in Vitis vinifera and additional studies should focus at unravelling the mechanisms underlying heat tolerance on the monoterpene-emitter grapevine clone.

Since the discovery of the aggregation-induced emission effect in 2001, diaminodicyanoquinone derivatives (DADQs) have presented interesting fluorescence properties, allowing them to be considered fluorescent dyes capable of showing quantum yields above 90%. Besides, the diaminodiacyanoquinone core represents a versatile building block propense either to modification or integration into different systems to obtain and provide them unique photophysical features. Herein, we carried out a theoretical study on the fluorescence properties of three different diaminodicyanoquinodimethane systems. Therefore, time-dependent density functional theory (TD-DFT) was used to obtain the values associated with the dipole moments, oscillator strengths, and the conformational energies between the ground and the first excited states of each molecule. The results suggest that only two of the three studied systems possess significant luminescent properties. In a further stage, the theoretical insights were confirmed by means of experimental measurements, which not only retrieved the luminescence of the DADQs, but also suggest a preliminary and promising antibacterial activity of these systems.

Objective: To investigate the effects and mechanisms of different concentrations of CCCP on mitophagy in human peripheral blood regulatory T cells. Methods: Tregs were isolated, identified and then grouped, treating with CCCP at a concentration of 2.5 μM, 5 μM, 10 μM, 20 μM and 40 μM for 24h in an incubator. Flow cytometry detected the reactive oxygen species (ROS), mitochondrial membrane potential (MMP), mitochondrial quality, and fluorescence microscopy observed the co-localization of mitochondria and lysosomes in each group. Results: The purity of CD4⁺CD25⁺Tregs was (93.36 ± 1.87) %. With the increase of CCCP concentration, the level of ROS gradually increased, while the MMP decreased gradually. About the mitochondria and lysosome fusion, the fluorescence intensity of orange (yellow) was the highest when the concentration of CCCP was in the range of 5-10 μM while decreased with the CCCP concentration continually increasing. The mitochondrial quality decreased with the increase of CCCP concentration. However, there was no significant difference between groups C, D and E. The mitochondrial quality of groups F and G were significantly lower than that of group E. Conclusions: With the concentration of CCCP gradually increased, the level of ROS in Treg cells increased, and MMP decreased, which promoted the mitophagy, mitochondrial quality maintains homeostasis; When ROS accumulated, and MMP decreased significantly, the mitophagy was inhibited, and the mitochondrial quality was significantly decreased.

Monitoring glycosylation changes within cells upon response to stimuli remains challenging because of the complexity of this large family of post-translational modifications (PTMs). We have developed an original tool enabling labeling and visualization of the cell cycle key-regulator b-catenin in its O-GlcNAcylated form based on intramolecular Förster resonance energy transfer (FRET) technology in cells. We opted for a bioorthogonal chemical reporter strategy based on the dual-labeling of b-catenin with a green fluorescent protein (GFP) for protein sequence combined with a chemically-clicked imaging probe for PTM resulting in a fast and easy to monitor qualitative FRET assay. We validated this technology by imaging the O-GlcNAcylation status of b-catenin in HeLa cells. Moreover, the changes in O-GlcNAcylation of b-catenin were varied by perturbing global cellular O-GlcNAc levels with inhibitors of O-GlcNAc transferase (OGT) and O-GlcNAcase (OGA). Finally, we provided a flowchart demonstrating how this technology is transposable to any kind of glycosylation.

A Zn(II) perchlorate complex has been prepared and characterized by single X-ray crystallography, nuclear magnetic resonance spectroscopy, thermogravimetric analysis, infrared spectroscopy, elemental analysis, and UV-vis spectroscopy. The complex crystallizes in the monoclinic space group P21/c (Z = 4) with a pentacoordinated zinc center. Interestingly, the Zn complex was found be to a potential fluorophore that could sense acetone and other ketones with high selectivity and sensitivity.

Chloroquine was among the first of several effective drug treatments against malaria until the onset of chloroquine resistance. In light of diminished clinical efficacy of chloroquine as an antimalarial therapeutic, there is potential in efforts to adapt chloroquine for other clinical applications, such as in combination therapies and in diagnostics. In this context, we designed and synthesized a novel asymmetrical squaraine dye coupled with chloroquine (SQR1-CQ). In this study, SQR1-CQ was used to label live Plasmodium falciparum (P. falciparum) parasite cultures of varying sensitivities towards chloroquine. SQR1-CQ positively stained ring, mature trophozoite and schizont stages of both chloroquine–sensitive and chloroquine–resistant P. falciparum strains. In addition, SQR1-CQ exhibited significantly higher fluorescence, when compared to a chloroquine-BODIPY (borondipyrromethene) conjugate. We also achieved successful SQR1-CQ labelling of P. falciparum directly on thin blood smear preparations. Drug efficacy experiments measuring half-maximal inhibitory concentration (IC50) showed lower concentration of effective inhibition against resistant strain K1 by SQR1-CQ compared to conventional chloroquine. Taken together, the versatile and highly fluorescent labelling capability of SQR1-CQ and promising preliminary IC50 findings potentiates it to be further developed as a promising diagnostic bioimaging tool with drug efficacy against chloroquine-resistant P. falciparum.

Keywords: flow mediated skin fluorescence; FMSF technique; NADH fluorescence, microcirculation, flowmotion, reactive hyperemia response, RHR, hypoxia sensitivity, HS, normoxia oscillatory index, NOI

Utilizing lignocellulosic biosourced platforms, we synthesized novel cyanostilbene (CS) deriva-tives featuring the 3,4-dimethoxyphenyl moiety. These derivatives were investigated for their emission properties in both solution and solid states. The two simple CS derivatives exhibit very weak luminescence in solution but significant luminescence in the solid state, indicating distinct Aggregation-Induced Emission (AIE) characteristic. Furthermore, combining these two CS units, without conjugation and with quasi perpendicular orientation, results in Dual-State Emission (DSE) fluorophore showing luminescence both in solution and solid states. X-ray crys-tallography studies on the solid-state compounds reveal a structure-emission relationship, demonstrating that the colour emission correlates with the conformations adopted by the mol-ecules in the solid state, which influence the type of stacking.

Lysine plays a crucial role in promoting development, enhancing immune function, and improving the function of central nervous system tissues. The two configurational isomers of amino acids have significantly different effects. Currently, methods for chiral recognition of lysine all have drawbacks such as expensive equipment and complicated detection processes, whereas fluorescence analysis boasts high sensitivity, strong selectivity, and simple operation. In this study, we synthesized four novel Binaphthyl-Amine (BINAM)-based fluorescent probes capable of specifically identifying the L-configuration of lysine among the twenty amino acids constituting human proteins. The enantiomeric fluorescence enhancement ratio (ef or ΔIL/ΔID) reached up to 15.29, demonstrating high enantioselectivity. We also evaluated the probe's recognition ability under different pH, reaction times, and metal ion conditions, as well as the Limit of Detection of the probe. Our findings indicate that this probe is a highly stable tool for detecting chiral lysine.

The beta-galactoside-binding mammalian lectin galectin-1 can bind, via its carbohydrate recognition domain (CRD), various cell surface glycoproteins and has been implicated in a range of cancers. As a consequence of binding to sugar residues on cell surface receptors it has been shown to have a pleiotropic effect across many cell types and mechanisms resulting in immune system modulation and cancer progression. As a result, it has started to become a therapeutic target for both small and large molecules. In previous studies, we have used fluorescence polarisation (FP) assays to determine KD values to screen and triage small molecule glycomimetics that bind to the galectin-1 CRD. In this study surface plasmon resonance (SPR) was used to compare human and mouse galectin-1 affinity measures with FP as SPR has not been applied for compound screening against this galectin. Binding affinities for a selection of mono- and di-saccharides covering a 1,000-fold range correlated well between FP and SPR assay formats for both human and mouse galectin-1. It was shown that slower dissociation drove the increased affinity at human galectin-1 whilst faster association was responsible for the effects at mouse galectin-1. This study demonstrates that SPR is a sound alternative to FP for early drug discovery screening and determining affinity estimates. Consequently, it also allows association and dissociation constants to be measured in a high throughput manner for small molecule galectin-1 inhibitors.

Arthrospira platensis is a class of microalgae with high economic value. Its high adaptability, high photosynthetic efficiency, and fast growth rate make it one of the few microalgae that can be cultivated on a large scale. Therefore, using the selenium enrichment property of Arthrospira platensis to cultivate selenium-enriched Arthrospira platensis will not only enhance the physiological efficacy of Arthrospira platensis but also increase its economic value significantly. In this study, we investigated the effects of sodium selenite on the growth and photosynthetic performance of Arthrospira platensis selenium by setting different amounts and methods of sodium selenite addition, and we explored the optimal culture conditions. The results showed that the experimental group treated with sodium selenite at 120 mg/L had the fastest growth, and the contents of soluble protein, phycocyanin, and Chlorophyll a increased by approximately 67.9%, 1.44 times, and 38.8%, respectively, compared to the control group. Superoxide dismutase (SOD) and catalase (CAT) activity increased by 1.88-fold and 65%, respectively, and malondialdehyde (MDA) levels were reduced by 62% compared to the control group. The results of the OJIP assay showed that the J and I points were significantly higher at the batch addition and treatment concentration of 120 mg/L, with the rate of QA being reduced and the proportion of the slowly reduced PQ pool being increased. The values of the maximum light energy conversion efficiency (Fv/Fm) per unit of reaction center were higher in both sodium selenite treatment groups than in the control group, indicating that the light energy conversion efficiency of Arthrospira was promoted under all concentration treatment conditions. The batch addition of sodium selenite at concentrations less than 120 mg/L resulted in significantly higher ABS/RC values than the control, and they were far superior to the one-time addition method. The reason for this may have been that the batch addition of sodium selenite at low concentrations increased the light absorption capacity of the unit reaction center of the Arthrospira PSII, resulting in a rise in captured light energy, a rise in the energy captured by the reaction center for electron transfer (ETo/RC), a decrease in the energy dissipated in the absorption of light energy by the reaction center (DIo/RC), and an increase in the photosynthetic performance index (PI abs).

Basil (Ocimum basilicum L.) is one of the important medicinal and aromatic plants. Light intensity is an indispensable factor for plants due to its effect on photosynthesis and physiological processes. Here, we investigated the impact of light intensities and harvesting times on the photosynthesis of green and purple basil. The experiment involved subjecting the plants to three different sunlight levels for 12 days: complete – 100%, 50%, and 30% sunlight. In addition, we scrutinize the harvesting time. The highest levels of photosynthetic and protective pigments were detected under full sunlight conditions in the purple basil harvested at noon. The highest levels of soluble and storage carbohydrates were recorded in the purple basil grown under full sunlight and harvested in the early morning. In contrast, their lowest levels were obtained in plants grown under 30% sunlight and harvested at noon time. Under all light treatments, the maximum quantum yield of photosystem II (FV/FM) was detected at 4 a.m. in both basil varieties; it decreased at noon and increased again at 5 p.m. Non-Photochemical Quenching (NPQ) got most elevated in the green variety under all light intensities at noon. However the highest NPQ was detected in the purple variety at 8 a.m. The NPQ was lowest in both basil varieties during the early morning and afternoon. Full sunlight at noon caused temporary photoinhibition and reduced car-bohydrates while enhancing pigment concentration and photo-protective mechanisms in basil plants.

The urban environment induces stress on trees and the impact can be identified by observing the condition of the crown. The aim of this study is to correlate the variables crown density (Cdn), crown transparency (Ctr) and dieback (Cdie) with the following vegetation indices: normalized difference vegetation index (NDVI), enhanced vegetation index (EVI2), blue normalized difference vegetation index (BNDVI), green normalized difference vegetation index (GNDVI), green-red vegetation Index (GRVI) and red-green-blue vegetation index (RGBVI) of the tree crown located in urban green areas, as well as chlorophyll fluorescence (Fv/Fm) as an indirect indicator of tree health condition. A total of 549 trees were evaluated, represented in 24 families, 36 genera and 53 species; the variables had average values of 67.96 % in Cdn, 35.19 % in Ctr and 1 % in Cdie. Correlations were found between Fv/Fm, NDVI and BNDVI. NDVI and BNDVI correlated with variables such as Cdn and Ctr, mainly in species such as Ligustrum lucidum, Jacaranda mimosifolia and Fraxinus uhdei. Therefore, it is possible to evaluate tree health condition of trees in urban green environments through the identification of unfavorable conditions at the crown level by using vegetation indices for some of the species studied.

Experimental systems to simulate future elevated CO2 conditions in the field often have large, rapid fluctuations in CO2. To examine possible impacts of such fluctuations on photosynthesis, intact leaves of field grown plants of five species were exposed to two-minute cycles of CO2 between 400 and 800 mol mol-1 lasting a total of 10 minutes, with photosynthesis, stomatal conductance and PSII fluorescence measured at the end of each half-cycle, and also 10 minutes after the end of the cycling. Prior to the cyclic CO2 treatments, steady-state responses of leaf gas exchange and fluorescence to CO2 were determined. In four of the five species, in which stomatal conductance decreased with increasing CO2, the cyclic CO2 treatments reduced stomatal conductance. In those species, both photosynthesis and the photochemical efficiency of PSII were reduced at limiting internal CO2 levels, but not at saturating CO2. In the fifth species, there was no change in stomatal conductance with CO2, and no change in either photosynthesis or PSII efficiency at any CO2 level with CO2 cycling. It is concluded that in many, but not all, species fluctuations in CO2 may reduce photosynthesis at low CO2 partly by decreasing the photochemical efficiency of photosystem II, as well as by decreasing stomatal conductance.

In the past decade, the idea that single populations of neurons support cognition and behavior has gradually given way to the realization that connectivity matters, and that complex behavior results from interactions between remote yet anatomically connected areas that form specialized networks. In parallel, innovation in brain imaging techniques has led to the availability of a broad set of imaging tools to characterize the functional organization of complex networks. However, each of these tools poses significant technical challenges and faces limitations, which require careful consideration of their underlying anatomical, physiological and physical specificity. In this review, we focus on emerging methods for measuring spontaneous or evoked activity in the brain. We discuss methods that can measure large-scale brain activity (directly or indirectly) with relatively high temporal resolution, from milliseconds to seconds. We further focus on methods designed for studying the mammalian brain in preclinical models, specifically in mice and rats. This field has seen a great deal of innovation in recent years, facilitated by concomitant innovation in gene editing techniques and the possibility of more invasive recordings. This review aims to give an overview of currently available preclinical imaging methods and an outlook on future developments. This information is suitable for educational purposes and for assisting scientists in choosing the appropriate method for their own research question.

Silk fibroin is a well-known biopolymer used in several applications in which the interaction with biological tissue is required. In fact, fibroin is extremely versatile and can be shaped to form several constructs useful in tissue engineering applications. Confocal imaging is usually per-formed to test the cells behaviour on the construct and in this context the fibroin autofluorescence is regarded as a problem. In addition, the autofluorescence is not intense enough to provide useful morphological images. In fact, to control study the constructs morphology other techniques are used (i.e. SEM, Micro-CT). In this work we propose a method based on the fluorescence energy transfer (FRET) to suppress the fibroin autofluorescence moving it to higher wavelength accessible to the confocal microscopy for a direct imaging.

Phosphodiesterases (PDEs) hydrolyze cyclic nucleotides to modulate multiple signaling events in cells. PDEs are recognized to actively associate with cyclic nucleotide receptors (Protein Kinases, PK) in larger macromolecular assemblies referred to as signalosomes. Complexation of PDEs with PK generates an expanded active site which enhances PDE activity. This facilitates signalosome-associated PDEs to preferentially catalyze active hydrolysis of cyclic nucleotides bound to PK, and aid in signal termination. PDEs are important drug targets and current strategies for inhibitor discovery are based entirely on targeting conserved PDE catalytic domains. This often results in inhibitors with cross-reactivity amongst closely related PDEs and attendant unwanted side effects. Here, our approach targets PDE-PK complexes as they would occur in signalosomes, thereby offering greater specificity. Our developed fluorescence polarization assay has been adapted to identify inhibitors that block cyclic nucleotide pockets in PDE-PK complexes in one mode, and disrupt protein-protein interactions between PDEs and cyclic nucleotide activating protein kinases in a second mode. We tested this approach with three different systems: cAMP-specific PDE8-PKAR, cGMP-specific PDE5-PKG and dual-specificity RegA-RD complexes and ranked inhibitors according to their inhibition potency. Targeting PDE-PK complexes offers biochemical tools for describing the exquisite specificity of cyclic nucleotide signaling networks in cells.

The inherent trace quantity of primary fatty acid amides found in biological systems presents challenges for analytical analysis and quantitation, requiring a highly sensitive detection system. The use of microfluidics provides a green sample preparation and analysis technique through small-volume fluidic flow through micron-sized channels embedded in a PDMS device. Microfluidics provides the potential of having a micro total analysis system where chromatographic separation, fluorescent tagging reactions, and detection are accomplished with no added sample handling. This study describes the development and optimization of a microfluidic-laser indued fluorescence (LIF) analysis and detection system that can be used for the detection of ultra-trace levels of fluorescently tagged primary fatty acid amines. A PDMS microfluidic device was designed and fabricated to incorporate droplet-based flow. Droplet microfluidics have enabled on-chip fluorescent tagging reactions to be performed quickly and efficiently, with no additional sample handling. An optimized LIF optical detection system provided fluorescently tagged primary fatty acid amine detection sub-fmol (436 amol) LODs. The use of this LIF detection provides unparalleled sensitivity, with detection limits several orders of magnitude lower than currently employed LC-MS techniques and might be easily adapted for use as a complementary quantification platform for parallel MS-based -omics studies.

Two 2,2':6',2''-terpyridine-based Schiff bases (TPySSB and TPySB) have been synthesized. The TPySSB shows remarkable selective ‘off-on’ fluorescence for Al³⁺ by photoinduced electron transfer (PET) mechanism of sensing. Chemosensor TPySSB binds Al³⁺ in a 1:2 ratio with an association constant 6.8×10⁵ (R²=0.98) and this 1:2 stoichiometric model is established on Job’s plot and ¹H NMR. Compared TPySSB and TPySB, it is of great importance of the existence of salicylidene unit due to its strong binding abilities of both phenol and C=N structure to the Al³⁺.

1) Background: Traditionally, complex biological products such as vaccines presented unique challenges to implementation of even rudimentary characterization packages; thus, the product was defined almost exclusively by its manufacturing process. The advances in technology and analytical tools allowed the application of more comprehensive characterization packages for products such as adsorbed combination vaccines, which contain several antigens in a single formulation to protect against more than one disease, and may contain adjuvants and excipients. Aluminum phosphate (AlPO4) is a well-established adjuvant for enhancing the uptake of vaccines and to induce robust immunity against pathogens. During manufacturing, adjuvant is mixed with protein antigens which may in turn impact their higher order structure and stability. 2) Methods: To study the structural changes of protein antigens after adsorption several analytical tools including DLS, FTIR, Fluorescence, LD, and SEM were used. 3) Results: the AlPO4 adjuvant suspension consists of small submicron particles that form a continuous porous surface. Secondary structure alpha-helix and beta-sheet content of DT and TT increased after adsorption to AlPO4 adjuvant, whereas no significant changes were noted for other protein antigens. Interactions were noted between AlPO4 adjuvant and DT, TT, and FHA. 4) Conclusions: here we report for the first time the use of SEM for the visualization of adsorbed multivalent vaccine components. A unique signature profile detected for each multivalent vaccine by FTIR can be used as a lean in-process test to verify vaccine product composition and identity prior to filling.

The alkylation of 1,1,2-trimethyl-1H-benzo[e]indole with 2-chloroacetamide, followed by work-up of the reaction mixture with a base and the subsequent treatment of a crude product with acetic acid gives 10a,11,11-trimethyl-10a,11-dihydro-8H-benzo[e]imidazo[1,2-a]indol-9(10H)-one. The structure assignments were based on data from ¹H, ¹³C and ¹⁵N NMR spectroscopy. The optical properties of the obtained compound were studied by UV-vis and fluorescence spectroscopy.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

Rapid microscopic analysis of tissue is an essential diagnostic tool in oncological surgery. The gold standard for intraoperative histological tissue evaluation are frozen sections. However, frozen sections are prone to a variety of artefacts and require skilled staff and specialized lab equipment. A potential method for rapid intraoperative tissue evaluation that does not require fixation, freezing nor sectioning of the tissue, is ex vivo fluorescence confocal microscopy (FCM). The visualization of the structurally important extracellular matrix (ECM) in conventional ex vivo FCM lags behind the standards of conventional histology. The objective of this study was to find a stain that will improve the depiction of the ECM to resemble FFPE H&amp;E sections as closely as possible.

Polyanilines are a class of conductive polymers that have attracted significant interest in the field of organic electronics due to their unique properties. In this article, the fluorescence spectroscopy and photovoltaic properties of polyaniline-based thin films and copolymers are investigated. The study focuses on understanding the relationship between the composition and structure of polyanilines and their optical and electrical properties. The article discusses the results of experiments on the photoluminescent properties of S1-S9 copolymers in a DMSO solution and of thin-film photoresistors based on polyanilines. The findings reveal that the photovoltaic properties of the thin films depend on the conditions of their fabrication and their surface morphology. The solubility of polyanilines is excellent, making the production of electronic components compatible with modern printing technologies in organic electronics. The work also points out that the photoconductivity of polyanilines can be improved by incorporation of additional molecular groups into the polymer matrix. Overall, this study sheds light on the potential of polyanilines as promising materials for organic electronics and provides insights into how their properties can be optimized for specific applications.

N-maleimide-derivatized phospholipids are often used to facilitate protein anchoring to membranes. In autophagy studies, this is applied to the covalent binding of Atg8, an autophagy protein, to a phosphatidylethanolamine (PE) in the nascent autophagosome. However, the question remains on how closely the N-maleimide PE derivative (PE-mal) mimicks the native PE in the bilayer. In the present paper, spectroscopic and calorimetric techniques have been applied to vesicles containing either PE or PE-mal (together with other phospholipids) to compare the properties of the native and derivatized forms of PE. According to differential scanning calorimetry, and to infrared spectroscopy, the presence of PE-mal did not perturb the fatty acyl chains in the bilayer. Fluorescence spectroscopy and microscopy showed that PE-mal did not alter bilayer permeability either. However, fluorescence emission polarization of Laurdan and DPH probes indicated an increased order, or decreased fluidity, in the bilayers containing PE-mal. In addition, infrared spectral data from the phospholipid phosphate region revealed a PE-mal-induced conformational change of the polar heads, accompanied by an increased hydration. Globally considered, the results suggest that PE-mal would be a reasonable substitute for PE in model membranes containing reconstituted proteins.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

As an important organelle in eukaryotic cells, Golgi apparatus is responsible for processing and transporting proteins and lipids in cells. Precise monitoring the status of Golgi apparatus by targeting fluorescence imaging technology is of enormous importance but remains an attractive yet dramatically challenging task. In this study, we report the construction of the first Golgi apparatus targeted sensor with bright near-infrared fluorescence, termed as Golgi-Pdots. As a start point of our investigation, hydrophobic CDs with bright NIR fluorescence at 674 nm (fluorescence quantum yield : 12.18%), narrow emission band of 23 nm, and excellent stability were facilely prepared from Magnolia Denudata flowers through an ultrasonic method. Incorporating the CDs into a polymer matrix modified with Golgi-targeting molecules can produce the water-soluble Golgi-Pdots, which showed high colloidal stability and similar optical properties as compared to CDs. Further studies revealed that the Golgi-Pdots showed good biocompatibility and Golgi-targeting ability. Based on these fascinating properties, Golgi-Pdots have been successfully used for long term bioimaging of Golgi apparatus inside live cells.

When oxidizing reduced sulfur compounds, the phototrophic sulfur bacterium Allochromatium vinosum forms spectacular sulfur globules as obligatory intracellular – but extracytoplasmic – intermediates. The globule envelope consists of three extremely hydrophobic proteins: SgpA and SgpB are very similar and can functionally replace each other. SgpC is involved in the expansion of the sulfur globules. The presence of a fourth protein, SgpD, has been suggested by comparative transcriptomics and proteomics of enriched sulfur globules. Here, we investigated the in vivo function of SgpD by coupling its carboxy-terminus to mCherry. This fluorescent protein requires oxygen for chromophore maturation, but we were able to use it in anaerobically growing A. vinosum provided the cells were exposed to oxygen for one hour prior to imaging. While mCherry lacking a signal peptide resulted in low fluorescence evenly distributed throughout the cell, fusion with SgpD carrying its original Sec-dependent signal peptide targeted mCherry to the periplasm and co-localized it exactly with the highly light-refractive sulfur deposits seen in sulfide-fed A. vinosum cells. Insertional inactivation of the sgpD gene showed that the protein is not essential for the formation and degradation of sulfur globules.

The device and method in accordance with the constant pressure regulation of micro droplet PCR in microfluidic chips are developed to explore the optimization way for the micro droplet movement, fragmentation, and bubble generation in microfluidic chips in existing digital PCR technology. In the developed device, an air source device is adopted to regulate the pressure in the chip, such that micro droplet generation and PCR amplification without bubbles can be achieved. In 3 min, the sample in 20ul will be distributed into nearly 50,000 water-in-oil droplets exhibiting a diameter of about 87μm, and the micro droplet will be subjected to a close arrangement in the chip without air bubbles. The device and chip are adopted to quantitatively detect the human gene . As indicated by the experimental results, a good linear relationship exists between detection signal and DNA concentration ranging from 101~ 105 copies /μL (R2=0.999). The micro droplet PCR devices based on constant pressure regulation chips exhibit a wide variety of advantages (e.g., achieving high pollution resistance, micro droplet fragmentation and integration avoidance, reducing human interference, and standardizing results). Thus, micro droplet PCR devices based on constant pressure regulation chips have promising applications in nucleic acid quantification.

Dawn of the omics revolution in biological sciences meant that we seek to understand more and in greater detail the molecular constituents of cells and biological systems. While we have gained significant insights from conventional omics tools, we now seek to understand the spatial dimensions of the data where subcellular localisation may impact on cellular physiology and phenotype. This review paper seeks to address current questions in the new field of image-based spatial proteomics as well as outline future challenges of the field. At first glance, spatial proteomics offers enormous potential to expand our understanding of different cell types in different disease and cell states. But limitations in types of fluorophores and issues with spectral overlap significantly hampers the practical implementation of the technique. On the other hand, while we have super-resolution microscopy techniques such as STED, PALM and STORM able to achieve 10 to 20 nm spatial resolution in single molecule localisation, problems with slow image acquisition limits high temporal resolution tracking of multiple protein targets in live cell imaging. Hence, the field of spatial proteomics is a mix of promises and challenges where we could image, in multi-colour, upwards of 10 well-chosen proteins that could inform on the molecular mechanisms of selected biological processes, but, at present, the method could not tackle larger scale questions. In essence, current implementation of image-based spatial proteomics is useful, but it is unable to fulfil the mission of large-scale projects such as the Human Protein Atlas or Human Cell Atlas. Future challenges in the field includes the development of more fluorophores (especially photoswitchable and photoactivable ones) for single molecule localisation microscopy, as well as seeking to improve temporal resolutions to the sub-millisecond range.

Background: This literature review investigates qualitative and quantitative uses of indocyanine green (ICG) in surgical treatment, as this novel technique has become increasingly popular in ORs (operating rooms) worldwide due to its many advantages. Method: An extensive literature review was performed by searching for relevant terms in 5 international databases (www.pubmed.gov, www.sciencedirect.com, www.scopus.com, www.Oxfordjournals.com, www.reaxys.com). The results of this search were summarized into the main advantages of employing ICG in colorectal surgery as follows: a) intraoperative fluorescence angiography capability; b) fluorescence-guided identification of lymph node involvement in colorectal cancer and the sentinel lymph node method; c) positive fluorescence flagging of a liver tumour as small as "only" 200 tumour cells; d) facilitation of fistula diagnosis; and e) tumour tattooing. Moreover, in addition to qualitative intraoperative ICG use, this technique can be combined with quantitative methods and parameters, such as maximum intensity, relative maximum intensity, and different inflow parameters (time-to-peak, slope, and t1/2max). The conclusion of this article is that fluorescence surgery with ICG aided by near-infrared (NIR) light is a relatively recent technology, an advantage of which is improving the specific anatomic and functional information provided, thus allowing more comprehensive and safer tumour removal as well as preservation of important structures.

Malignant pleural mesothelioma (MPM) has limited treatment options and poor prognosis. Frequent inactivation of the tumour suppressors BAP1, NF2 and P16 may differentially sensitise tumours to treatments. We have established chick chorioallantoic membrane (CAM) xenograft models of low-passage MPM cell lines and protocols for evaluating drug responses. Ten cell lines, representing the spectrum of histological subtypes and tumour suppressor status, were dual labelled for fluorescence/bioluminescence imaging and implanted on the CAM at E7. Bioluminescence was used to assess viability of primary tumours, which were excised at E14 for immunohistological staining or real-time PCR. All MPM cell lines engrafted efficiently forming vascularised nodules, however their size, morphology and interaction with chick cells varied. MPM phenotypes including local invasion, fibroblast recruitment, tumour angiogenesis and vascular remodelling were evident. Bioluminescence imaging could be used to reliably estimate tumour burden pre- and post-treatment, correlating with tumour weight and Ki-67 staining. In conclusion, MPM-CAM models recapitulate important features of the disease and are suitable to assess therapies using a broad range of MPM cell lines that allow histological or genetic stratification. They are amenable to multi-modal imaging, offering a time and cost-efficient, 3Rs-compliant alternative to rodent xenograft models to prioritise candidate compounds from in vitro studies.

Recently, it was proposed that the thiophene ring is capable of promoting mitochondrial accumulation when linked to fluorescent markers. As a noncharged group, thiophene presents several advantages from a synthetic point of view, making it easier to incorporate such a side moiety into different molecules. Herein, we confirm the general applicability of thiophene group as mitochondrial carrier for drugs and fluorescent markers, based on a new concept of nonprotonable, noncharged transporters. We implemented this concept in a medicinal chemistry application by developing an anti-tumoral, metabolic chimeric drug, based on PDHK inhibitor dichloroacetate (DCA). The promising features of the thiophene moiety as a noncharged carrier for targeting mitochondria may represent a starting point for the design of new metabolism-aimed drugs.

A new type of gold nanoparticles was synthesized by using benzoyl pyrazolone as a capping agent. The synthesized AuNPs exhibited a spherical shape and a monodisperse and fluorescence emission characteristic peak at 650 nm. The AuNPs –BMPBP was demonstrated as sensitive and selective fluorescent chemosensor for detection of Al ³⁺ ion. In the presence of Al ³⁺ ion, the fluorescent emission of BMPBP-AuNPs at 650 nm, increased with an increasing concentration of Al ³⁺ ion with a low detection limit (2 µM), the proposed method provided to apply determination of Al ³⁺ ion of tap water with satisfactory results.

Quenchbody (Q-body), a new type of fluorescent immunosensor, is an antibody fragment labeled with a fluorescent dye. When Q-body binds to its antigen, the fluorescence intensity increases. Highly sensitive detection of antigens by changes in fluorescence intensity is performed in a single step by mixing sample and reagent. In this study, to reveal the structural basis for Q-body, we solved the crystal structures of antigen-binding fragment (Fab) of an anti-osteocalcin antibody KTM219, which is applicable to Q-body, and its complex with the antigen osteocalcin C-terminal peptide (BGP-C7). Also, we solved the structure of a KTM219 Fab crystal grown in the presence of a fluorescent dye 5(6)-carboxytetramethylrhodamine (TAMRA), however, a tightly bound TAMRA was not found in the electron density map. We predicted the binding site of TAMRA by docking simulations. These results support the structural basis for the Q-body mechanism as follows. In the absence of the antigen, the fluorophore located near tryptophan residues is quenched in the hydrophobic pocket of the antigen binding site between VH and VL. In association with the competitive binding of the antigen, the fluorophore is released from the antigen binding pocket and emits fluorescence. The crystal structures of KTM219 Fab and the structural basis of Q-body would be useful for further development and improvement of Q-body fluorescent immunosensors.

The pH dependence of the free energy level of the flash induced primary charge pair P+IA– was determined by combination of the results from indirect charge recombination of P+QA– and from delayed fluorescence of the excited dimer (P*) in reaction center of photosynthetic bacterium Rhodobacter sphaeroides where the native ubiquinone at the primary quinone binding site QA was replaced by low potential anthraquinone derivatives. The following observations were made: 1) The free energy state of P+IA– was pH independent below pH 10 (–370 ± 10 meV relative to that of the excited dimer P*) and showed remarkable decrease (about 20 meV/pH unit) above pH 10. A not insignificant part of the dielectric relaxation of the P+IA– charge pair (about 120 meV) should come from protonation related changes. 2) The single exponential decay character of the kinetics proves that the protonated/unprotonated P+IA– and P+QA– states are in equilibria and the rate constants of protonation konH +koffH is much larger than that of the charge back reaction kback ~103 s-1. 3) Highly similar pH profiles were measured for the free energy states of P+QA– and P+IA–, indicating that the same acidic cluster around QB should response to both anionic species. This was supported by model calculations based on anticooperative proton distribution in the cluster with key residues of GluL212, AspL213, AspM17 and GluH173 and on effect of polarization of the aqueous phase on the electrostatic interaction. The larger distance of IA– from the cluster (25.2 Å) than that of QA‒ (14.5 Å) is compensated by smaller effective dielectric constant (6.5 ± 0.5 and 10.0 ± 0.5, respectively). 4) The P* → P+QA− and IA‒QA → IAQA− electron transfers are enthalpy driven reactions with exemption of very large (>60%) or negligible entropic contributions in cases of substitution by 2,3-dimethyl-AQ or 1-chloro-AQ, respectively. The possible structural consequences are discussed.

Temperature and pressure sensors currently encounter challenges such as slow response times, large sizes, and insufficient sensitivity. To address these issues, we developed tetraphenylethylene (TPE)-doped polyvinylidene fluoride (PVDF) nanofiber membranes using electrospinning, with process parameters optimized through a convolutional neural network (CNN). We systematically analyzed the effects of PVDF concentration, spinning voltage, tip-to-collector distance, and flow rate on fiber morphology and diameter. The CNN model achieved high predictive accuracy, resulting in uniform and smooth nanofibers under optimal conditions. Incorporating TPE enhanced the hydrophobicity and mechanical properties of the nanofibers. Additionally, the fluorescent properties of the TPE-doped nanofibers remained stable under UV exposure and exhibited significant linear responses to temperature and pressure variations. The nanofibers demonstrated a temperature sensitivity of -0.976 gray value/°C and pressure sensitivity with an increase in fluorescence intensity from 537 a.u. to 649 a.u. under 600 g pressure. These findings highlight the potential of TPE-doped PVDF nanofiber membranes for advanced temperature and pressure sensing applications.

The field of fluorescence sensing, leveraging various supramolecular self-assembled architectures constructed from macrocyclic pillar[n]arenes, has seen significant advancement in recent decades. This review comprehensively discusses, for the first time, the recent innovations in the synthesis and self-assembly of pillar[n]arene-based supramolecular architectures (PSAs) containing metal coordination sites, along with their practical applications and prospects in fluorescence sensing. Integrating hydrophobic and electron-rich cavities of pillar[n]arenes into these supramolecular structures endow the entire system with self-assembly behavior and stimulus responsiveness. Employing the host–guest interaction strategy coupled with complementary coordination forces, PSAs exhibiting both intelligent and controllable properties are successfully constructed. This provides a broad horizon for advancing fluorescence sensors capable of detecting environmental pollutants. This review aims to establish a solid foundation for the future development of fluorescence sensing applications utilizing PSAs. Additionally, current challenges and future perspectives in this field are discussed.

Genetic engineering and directed evolution are effective methods to address the low yield and poor industrialization level of microbial target products. The current research focus is on how to efficiently and rapidly screen beneficial mutants from constructed large-scale mutation libraries. Traditional screening methods such as plate screening and well plate screening are severely limited in their development and application due to their low efficiency and high costs. In the past decade, microfluidic technology has become an important high-throughput screening technology due to its fast speed, low cost, high automation, and high screening throughput, and it has developed rapidly. Droplet-based microfluidic high-throughput screening has been widely used in various fields such as strain/enzyme activity screening, pathogen detection, single-cell analysis, drug discovery, and chemical synthesis, and has been widely applied in industries such as materials, food, chemicals, textiles, and biomedicine. In particular, in the field of enzyme research, droplet-based microfluidic high-throughput screening has shown excellent performance in discovering enzymes with new functions, improved catalytic efficiency or stability, acid-base tolerance, etc. Currently, droplet-based microfluidic high-throughput screening technology has achieved high-throughput screening of enzymes such as glycosidase, lipase, peroxidase, protease, amylase, oxidase, and transaminase, as well as high-throughput detection of products such as riboflavin, coumarin, 3-dehydroquinate, lactic acid, and ethanol. This article reviews the application of droplet-based microfluidics in high-throughput screening, with a focus on high-throughput screening strategies based on UV, visible, and fluorescence spectroscopy, including labeled optical signal detection screening, as well as label-free electrochemical detection, mass spectrometry, Raman spectroscopy, nuclear magnetic resonance, etc. Furthermore, the research progress and development trends of droplet-based microfluidic technology in enzyme modification and strain screening are also introduced.

We have investigated the canine of olive flounder in terms of the nonlinear optical signals of two-photon excitation autofluorescence (2PEF) and second harmonic generation (SHG), whereby two kinds of nonlinear microscope images of the canine were obtained using ~140 femtosecond pulses. For increasing excitation power of laser pulses, a photobleaching effect was found to be significant in the red and green ranges of autofluorescence, where a double-exponential decay of the intensity occurs within hundreds of second due to collagen fluorophores in the canine. In the blue range of autofluorescence, the photobleaching is suppressed due to an energy conversion of the incident laser pulse to SHG signal. As a result, the signal in blue range remains constant for long term exposure to laser. We have also found that the SHG intensity depends on the orienta-tion of linearly polarized excitation, and the optical anisotropy of SHG can be attributed to the collagen alignment of canines.

High-throughput research on bimetallic nanoparticles brought a vast overview of their characteristics and catalytic activities.¹ However, traditional bimetallic nano-allloy quantification methods serving catalyst preparations are not suitable for the fast and robust data output of high-throughput experiments. Hence, this work designed and validated a more fast, more neat, and reliable quantitative analysis using X-ray fluorescence spectroscopy for bimetallic nanoparticles synthesized by high-throughput setups. The results demonstrated this method to be accurate with high precision. Furthermore, the agreement to qualitative results from an energy-dispersive X-ray spectrometer equiped on a scanning electron microscope provided an option to quantify a bimetallic nano-alloy by just analyzing one of the two composing elements. Thus, this method is proved to be highly compatible with high-throughput experiments.

Needle abscission in balsam fir has been linked to both cold acclimation and changes in lipid composition. The overall objective of this research is to uncover lipid changes in balsam fir during cold acclimation and link those changes with postharvest abscission. Branches were collected monthly from September to December and assessed for cold tolerance via membrane leakage and chlorophyll fluorescence changes at -5, -15, -25, -35, and -45°C. Lipids were extracted and analyzed using mass spectrometry while postharvest needle abscission was determined gravimetrically. Cold tolerance and needle retention each significantly (P < 0.001) improved throughout autumn in balsam fir. There were concurrent increases in DGDG, PC, PG, PE, and PA throughout autumn and a decrease in MGDG. Those same lipids were strongly related to cold tolerance, though MGDG had the strongest relationship (R2 = 55.0% and 42.7% from membrane injury and chlorophyll fluorescence, respectively). There was a similar, albeit weaker, relationship between MGDG:DGDG and needle retention (R2 = 24.3%). Generally, a decrease in MGDG:DGDG ratio resulted in better cold tolerance and higher needle retention in balsam fir possibly due to increased membrane stability.