Green infrastructure systems are often overdesigned. This may be a byproduct of static sizing (e.g., accounting for a design storm’s runoff volume but not exfiltration rates) or may be deliberate (e.g., buffering against performance loss through time). Regardless, overdesign may compromise plants’ access to water in systems where soil pits are embedded in infiltration beds. It could raise the storm size required for water to reach soil pits, reducing water availability between storms, which could ultimately induce plant physiological stress. This study investigated the hydrological dynamics and water relations of a tree trench system suspected to have been overbuilt and identified factors contributing to, compounding, and mitigating the risk of plant stress. Results provided strong evidence that the abovementioned processes played out. Water in the infiltration bed reached soil pits only once in three years, with that event occurring during a hydrant release. Moreover, minimal water was retained in the soil pit during the event due to the hydraulic properties of the soil media. Through a growing season, one of the two tree types frequently experienced water stress, while the other did so only rarely. These contrasting responses can likely be attributed to roots either being largely confined to the soil pits or reaching a deeper water source. Implications of these results for green infrastructure design are considered.

Lamellar eutectic structure of Al_0.7CoCrFeNi high-entropy alloy (HEA) is emerging as a promising candidate for structural applications because of its high strength-ductility combination. The alloy consists of a fine-scale lamellar fcc+B2 microstructure with high flow stresses >1500 MPa under quasi-static conditions. The response to shear loading was not investigated so far. This is the first report on the shear deformation of an eutectic structured HEA and effect of precipitation on shear deformation. The dynamic shear response (DSR) of the eutectic HEA was examined in two microstructural conditions, with and without the presence of L1₂ precipitates. A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local DSR of the alloy. The adiabatic shear bands (ASBs) in two different microstructural conditions were characterized after deformation at dynamic strain rates. The adiabatic shear localization occurs at low strains for the high strength material, and the eutectic microstructure does not delay cracking. The width of ASBs and the extent of plastic deformation around them has been correlated with the rate of straining. Dynamic recrystallization within ASBs and profuse twinning around it was observed. Local mechanical response of individual lamellae before and after shear deformation was examined using nano-indentation.

Background: Cancer patients may fail to distinguish COVID-19 symptoms such as anosmia, dysgeusia/ageusia, anorexia, headache, and fatigue, which are frequent after cancer treatments. We aimed to identify symptoms associated with COVID-19 and to assess the strength of their association in cancer and cancer-free populations. Methods: The prospective multicenter cohort study PAPESCO-19 included 878 cancer patients and 940 healthcare workers (HCWs) systematically tested for SARS-CoV-2-specific antibodies. Participants reported the results of routine screening RT-PCR and thirteen COVID-19 symptoms. Backward logistic regression identified the symptom combinations significantly associated with COVID-19. Results: COVID+ proportions were similar in patients (8%) and HCWs (9.5%, p=0.26), whereas symptomatic proportions were lower in patients (32%) than HCWs (52%, p<0.001). Anosmia, anorexia, fever, headache, and rhinorrhea together accurately discriminated (c-statistic=0.7027) COVID-19 cases in patients. Anosmia, dysgeusia/ageusia, muscle pain, intense fatigue, headache, and chest pain better discriminated (c-statistic=0.8830) COVID-19 cases in HCWs. Anosmia had the strongest association in patients (OR=7.48, 95% CI: 2.96–18.89) and HCWs (OR=5.71, 95% CI: 2.21–14.75). Conclusions: COVID-19 symptoms and their diagnostic performance differ in cancer patients and HCWs. Anosmia is associated with COVID-19 for patients, while dysgeusia/ageusia are not. Cancer patients deserve tailored preventive measures due to their particular COVID-19 symptom pattern.

Nowadays, in order to improve asphalt pavement performance, durability and reduce environmental pollution caused by asphalt binder, many researchers are studying to modify asphalt concrete (AC) and find alternative paving materials to extend service life of asphalt pavement. One of the successful materials used in a modification of AC are fibers. Different types of fibers have been reinforced in AC mixture and improvements have been observed. This research studies the performance of glass wool fiber reinforced in a dense-graded asphalt mixture. Generally, glass fibers are known to have excellent mechanical properties such as high tensile modulus, 100% elastic recovery and a very high tolerance to heat. The glass wool fibers are commonly used as a thermal insulation material. In this research to evaluate the performance of glass wool fiber in AC, laboratory tests Marshall mix design test, Indirect tensile strength (IDT), Tensile strength ratio (TSR) and Kim test were conducted to determine a proper mix design, tensile properties, moisture susceptibility, rutting and fatigue behaviors. Results show that addition of glass wool fibers does affect the properties of AC mixture. The use of glass wool fibers showed a positive consistence results, in which it improved the moisture susceptibility and rutting resistance of the AC. Also result showed addition of fiber increased tensile strength and toughness which indicates that fibers have a potential to resist distresses that occur on a surface of the road as a result of heavy traffic loading. The overall results showed that addition of glass wool fiber in AC mixture is beneficial in improving properties of AC pavements.

This paper presents the development of a new system designed to measure the local temperature field in adiabatic shear band. Transient temperature field are simultaneously recorded by an array of 32 InSb infrared (IR) detectors and a streak camera working in visible-near infrared (VIS-NIR). Observations in IR offer a low temperature detection limit (350°C) but they are highly sensitive to uncertainty in the emissivity. Observations in VIS-NIR allow for measurement only at high temperatures (750°C) but they are less affected by uncertainty on emissivity and present a higher temperature sensitivity. By performing simultaneous measurements, it is possible to obtain data on a large temperature range with an improved accuracy at high temperature. The different sources of errors caused by uncertainty in the emissivity, spatial and temporal resolution of the detectors has been analyzed and an estimation of the total measurement uncertainty of the system is given.

In regions with low-temperature action transverse cracks can appear in asphalt pavements as a result of thermal stresses that exceed the fracture strength of materials used in asphalt layers. To better understand thermal cracking phenomenon, strength properties of different asphalt mixtures were investigated. Four test methods were used to assess the influence of bitumen type and mixture composition on tensile strength properties of asphalt mixtures: tensile strength using the Thermal Stress Restrained Specimen Test (TSRST) and the Uniaxial Tension Stress Test (UTST), flexural strength using the Bending Beam Test (BBT) and fracture toughness using the Semi-Circular Bending Test (SCB). The strength reserve behavior of tested asphalt mixtures was assessed as well. The influence of cooling rate on strength reserve was investigated and correlations between results from different test methods were also analyzed and discussed. It was observed that the type of bitumen is a factor of crucial importance to low-temperature properties of the tested asphalt concretes. This conclusion was proved by all test methods that were used. It was also observed that the level of cooling rate influences the strength reserve and, in consequence, resistance to low-temperature cracking. It was concluded that reasonably good correlations were observed between strength results for the UTST, BBT and SCB test methods.

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

The open communication is an exigent need for future power system where the time delay is unavoidable. In order to secure the stability of the grid, the frequency must remain within its limited range which is achieved through the load frequency control. The load frequency control signals are transmitted through communication networks which induces time delay that could destabilize the power systems. So, in order to guarantee the stability the delay margin should be computed. In this paper, we present a new method for calculating the delay margin in load frequency control systems. The transcendental time delay characteristics equation is transformed to frequency dependant equation. The spectral radius is used to find the frequencies at which the roots crosses the imaginary axis. The crossing frequencies are determined through the sweeping test and the binary iteration algorithm. A one-area load frequency control system is chosen as case study. The effectiveness of the proposed method has been proved through comparing with the most recent published methods. The method shows its merit with less conservativeness and less computations. The PI controller gains are preferable to be chosen large to reduce the damping, however, the delay margin decreases with increasing the PI controller gains.

Autonomic dysfunction is an increasingly recognised complication in chronic neurological conditions such as Parkinson’s disease , and other medical conditions, including diabetes mellitus, chronic fatigue syndrome, postural tachycardia syndrome with and without Ehlers-Danlos syndrome, fibromyalgia and recently Long Covid. Despite laboratory-based tests to evaluate normal and abnormal autonomic function, there are no home-based tests to record neuro-cardiovascular autonomic responses to common stimuli in daily life that are dependent on the normal functioning of the autonomic nervous system. We have developed an adapted blood pressure/heart Autonomic Profile (aAP) that can be used by an individual independently and repeatedly in a domiciliary setting to determine the physiological and symptomatic response to standing, food, and physical and mental (cognitive, emotional) activities. The aAP aids separating autonomic failure (often irreversible) from autonomic dysfunction. This helps the individual and attending healthcare professional understand the relationship between symptoms and common triggers in daily life and informs on self-management in debilitating conditions such as the postural tachycardia syndrome (PoTS) and Long Covid.

This brief note aims to explain the scope in conducting large-scale serological surveys of SARS-CoV-2 to define the landscape of population immunity without overlooking the inherent uncertainty steaming from sampling design and diagnostic validity. The note completes with a succinct statistical appendix of simple methods for estimating prevalence from random population samples using imperfect diagnostic tests.

Thermal stresses belong to the leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature properties of asphalt mixtures, three point bending and uniaxial tensile creep tests were applied and the master curves of stiffness modulus were analyzed. On the basis of creep test results, rheological parameters describing elastic and viscous properties of the asphalt mixtures were determined. Thermal stresses were calculated and compared to tensile strength of the material to obtain the failure temperature of the analyzed asphalt mixtures. It was noted that lower strain values of creep curves were obtained for the Tensile Creep Test (TCT) than for the Bending Beam Creep Test (BBCT), especially at lower temperatures. Results of thermal stress calculations indicated that higher reliability was obtained for the viscoelastic Monismith method based on the TCT results than for the simple quasi-elastic solution of Hills and Brien. The highest agreement with the TSRST results was also obtained for the Monismith method based on the TCT results. No clear relationships were noted between the predicted failure temperature and different methods of thermal stress calculations.

Chronic diseases are still known as incurable diseases, and we suspect that the medical research model is unfit for characterizing chronic diseases. In this study, we examined accuracy and reliability required for characterizing chronic diseases, reviewed implied presumptions in clinical trials and assumptions used in statistical analysis, examined sources of variances normally encountered in clinical trials, and conducted numeric simulations by using hypothetical data for several theoretical and hypothetical models. We found that the sources of variances attributable to personal differences in clinical trials can distort hypothesis test outcomes, that clinical trials introduce too many errors and too much inaccuracies that tend to hide weak and slow effects of treatments, and that the means of treatments used in statistical analysis have little or no relevance to specific patients. We further found that a large number of uncontrolled co-causal or interfering factors normally seen in human subjects can greatly enlarge the means and the variances of the experimental errors, and the use of high rejection criteria (e.g., low p values) further raises the chances of failing to find treatment effects. As a whole, we concluded that the research model using clinical trials is wrong on multiple grounds, under any of our realistic theoretical and hypothetical models, and that misuse of statistical analysis is most probably responsible for failure to identify treatment effects for chronic diseases and to detect harmful effects of toxic substances in the environment. We proposed alternative experimental models involving the use of single-person or mini optimization trials for studying low-risk weak treatments.

This paper presents results from numerical and experimental investigation on Charpy tests in order to point out failure mechanisms and to evaluate new polymeric blends PP+PA6+EPDM. Charpy tests were done for initial velocity of the impactor of 0.96 m/s and its mass of 3.219 kg and these data were also introduced in the finite element model. The proposed model take into account the system of four balls, including support and the ring of fixing the three balls and it has a finer discretization of the impact area to highlight the mechanisms of failure and their development in time. The constitutive models for four materials (polypropylene with 1% Kritilen, two blends PP+PA6+EPDM and a blend PA6+EPDM) were derived from tensile tests. Running simulations for each constitutive model of material makes possible to differentiate the destruction mechanisms according to the material introduced in the simulation, including the initiation and the development of the crack(s), based on equivalent plastic strain at break (EPS) for each material. The validation of the model and the simulation results was done qualitatively, analysing the shape of broken surfaces and comparing them to SEM images and quantitatively by comparing the impact duration, energy absorbed by the sample, the value of maximum force during impact. The duration of the destruction of the specimen is longer than the actual one, explainable by the fact that the material model does not take into account the influence of the material deformation speed in Charpy test, the model being designed with the help of tests done at 0.016 m/s (1000 mm/min) (maximum strain rate for the tensile tests). Experimental results are encouraging for recommending the blends 20% PP+42% PA6+28% EPDM and 60% PA6+ 40%EPDM as materials for impact protection at low velocity (1m/s). Simulation results are closer to the experimental ones for the more brittle tested materials (with less content of PA6 and EPDM) and more distanced for the more ductile materials (with higher content of PA6 and EPDM).

This investigation was conducted to determine the chemical composition and nutritional value of five plant species commonly used as ruminant feeds namely: Artemisia herba-alba, Acer monspessulanum, Amygdalus lycoides, Amygdalus scoparia, and Atriplex leucoclada. After the collecting samples, the chemical compositions of plants included dry matter (DM), organic matter (OM), crude protein (CP), ether extract (EE), ash (CA), cell wall (NDF), and non-lignin cell wall (ADF) were determined according to standard methods. For degradation testing, the nylon bag technique was applied using three native Sistani fistula calves. Organic matter digestibility (OMD) and metabolisable energy (ME) were determined through the gas production technique. The CP value ranged from 5.30 (Amygdalus scoparia) to 11.72% (Atriplex leucoclada) while NDF value ranged from 52.62 (Amygdalus lycoides) to 69.05% (Amygdalus scoparia). The range of OMD, DOMD, and ME was from 36.67 to 53.27%, 34.67 to 49.11%, and 5.57 to 8.08 (MJ/kg), respectively. The results showed a positive correlation between cell wall composition and dry matter digestibility in plant species. The nutritional value of Amygdalus lycoides, Atriplex leucoclada, Acer monspessulanum, and Artemisia herba-alba was acceptable composition and digestibility.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

The aim of this study was to identify the differences in functional fitness and quality of life among women over 60 years of age depending on their level of objectively measured physical activity (PA) according to Global Recommendations on Physical Activity for health. The study used cross-sectional design with 213 volunteered women over 60 years of age. Physical activity was monitored for 7 days of the week using Actigraph Gt3x monitor. The Senior Fitness Test battery and Hand-grip strength tests were performed to assess functional fitness. Quality of life was self-reported using short version of WHOQOL-brief questionnaire. Women who met the PA recommendations achieved slightly better results in most functional tests and all domain of quality of life. The significant differences were found in upper body strength, dynamic balance and social relationships domain of quality of life. Physical activity programs developed on the basis of WHO recommendations have the potential to improve functional capacity and quality of life. However, further experimental studies in this area are required.

This research aims to investigate the carbon fiber reinforced polymer (CFRP) when subjected to tensile, bending, and compression. Half of the specimens are also subjected to water to find out how water influences. The CFRP is created using a combination of carbon fiber layers and epoxy resin Bisphenol A Epichlorohydrin with hardener and is formed using the vacuum infusion method. From the water absorption test, it was found that the average weight gain of the specimens was 2.9% and the lowest value was at 0.6%, it was concluded that the increase in wet specimen weight was not too significant and water absorption tended to be slow. Mechanical testing ob-tained the highest average tensile stress, bending stress, compressive stress, and modulus of elasticity of 195 MPa, 295 MPa, 96 MPa, and 8914 MPa were from dry specimens while the lowest average values were 146 MPa, 286 MPa, 81 MPa, and 6160 MPa from wet specimens. The results of micro-photo observations on the tensile test fracture show that the specimen has a XGM fracture character with delamination and splitting fractures happening in multiple areas. In the bending test, the specimens experienced buckling fracture due to the fiber breaking and the inability of the matrix to withstand the additional stress. Shear fracture happened during the compressive test. In conclusion, water absorption has a bad impact towards the composite strength.

This paper analyses the evolution of the internal damage in two types of steel that show different fracture behaviours, with one of them being the initial material used for manufacturing prestressing steel wires, which shows a flat fracture surface perpendicular to the loading direction, and the other one being a standard steel used in reinforced concrete structures, which shows the typical cup-cone surface. 3mm-diameter cylindrical specimens are tested with a tensile test carried out in several loading stages and, after each of them, unloaded and analysed with X-ray tomography, which allows detection of internal damage throughout the tensile test. In the steel used for reinforcement, damage is developed progressively in the whole specimen, as predicted by Gurson-type models, while in the steel used for manufacturing prestressing steel-wire damage is developed only in the very last part of the test. In addition to the experimental study, a numerical analysis is carried out by means of the finite element method by using a Gurson model to reproduce the material behaviour.

Background: The 6-minute walk test (6MWT) is a simple and low-cost method that allows assessment of functional capacity in patients with heart failure (HF). However, the prognostic role of 6MWT in HF remains uncertain. Objectives: We aimed to evaluate the 6MWT as a predictor of mid-term adverse outcomes in patients with HF with mid-range and reduced ejection fraction. Methods: Prospective single-center cohort study that included patients with HF with an ejection fraction under 50% at a specialized outpatient HF service. Patients underwent the 6MWT on admission and were compared according to the distance walked: Group I walked ≥350 meters and group II <350 meters. The primary outcome was a composite of death from any cause or hospitalization for HF decompensation in one-year follow-up. Secondary outcomes were the components of the primary outcome in an isolated analysis. Results: Sixty patients were included, 43.3% male, with a mean age of 61.1 ± 12.9 years and ejection fraction 34.3 ± 10.1%. 52 patients (86.7%) were on guideline-directed triple therapy for HF. The average distance walked in the 6MWT was 395.1 ± 98.8 meters, with 40 patients (66.7%) in group I and 20 (33.3%) in group II. The primary outcome in groups I and II were, respectively, 15,0% and 35,0% (p=0.05). One-year mortality was 5.0% vs 15.0% (p=0.18) and the hospitalization rate was 10.0% vs 20.0% (p=0.28). Conclusions: There was no association of distance <350 meters in the 6MWT with the primary outcome in patients with HF. Despite the higher occurrence of outcomes in group II, the difference was not statistically significant in this analysis. On a selective basis, the 6MWT may be a useful tool for prognostic stratification in HF, if combined with other methods.

Wave overtopping, i.e., excess of water over the crest of a coastal protection infrastructure due to wave run-up, of a smooth slope can be reduced by introducing slope roughness. A stepped revetment ideally constitutes a slope with uniform roughness. Apart from reducing overtopping, a stepped revetment provides safer access to a beach compared to conventional rubble. In recent years, research studies on stepped revetments have provided valuable findings regarding the performance and design optimization of stepped revetments as a typical mean of coastal protection. A stepped revetment can reduce overtopping volumes of breaking waves up to compared to a smooth slope. The effectiveness of the overtopping reduction decreases with increasing Iribarren number. However, up to date a unique approach applicable for a wide range of boundary conditions is still missing. The present paper critically reviews previous findings, gathers and analyzes data from previous studies and proposes a new formula for robust prediction of overtopping of stepped revetments. By means of this approach a critical assessment based on beforehand disclosed parameter ranges between a smooth slope on the one hand and a plain vertical wall on the other are contrasted. By analysis of a new data set compounded from different original studies a novel empirical formulation is derived to predict the roughness reduction coefficient of a stepped revetment for breaking and non-breaking waves. This coefficient is developed and adjusted for a direct incorporation into the present design guidelines. Underlying uncertainties are clearly addressed and quantified. Scale effects are highlighted.

Cannabidiol (CBD) is a non-intoxicating compound extracted from Cannabis sativa, showing antidepressant-like effects in different rodent models. However, inconsistent results have been described depending on the species and the strain used to assess depressive-like behaviour. Moreover, only a few studies have investigated the effect of CBD in female rodents. Therefore, we aimed to i) investigate the effects of CBD in two different strains of mice (Swiss and C57BL/6) and in a rat model of depression based on selective breeding (Flinders Sensitive and Resistant Lines, FSL and FRL) subjected to tests predictive of antidepressant-like effects; and ii) investigate the influence of sex in the effects of CBD in both mice and rats. CBD induced an antidepressant-like effect in male Swiss but not in female Swiss or C57BL/6 mice in the tail suspension test (TST). In male FSL rats, CBD produced an antidepressant-like effect one-hour post-injection. However, in female FSL, CBD induced a bimodal effect, increasing the immobility time at one hour and decreasing it at two hours. Ketamine produced an antidepressant-like effect in male and female FSL rats at different doses. In conclusion, strain, sex, and administration time affect CBD's behavioural response to rodents exposed to tests predictive of antidepressant effects.

Particle size can pose a challenge to random embankment compaction control methods, where practical techniques have hardly been developed and procedural control is used instead. In order to develop new quality control procedures for slate random fill, the necessary fieldwork and laboratory tests were carried out. This involved the revision of certain methods such as the wheel-tracking or topographic settlement tests. More than six hundred in-situ density and moisture content measurements were carried out for this research. In addition, more three hundred topographic settlements and three hundred wheel-tracking carriage tests were performed. The quality control processes were completed with more than thirty plate bearing tests. Possible evidence of statistical correlations between compaction control tests were identified. An analysis of variance (ANOVA) was performed. When testing proved relationships between them, the replacement of one of them by the other was assessed by deduction. Finally, the study suggests new procedures for compaction quality control of random slate fill used in crown area.

Cervical cancer is a worldwide public health problem with a high rate of illness and mortality among women. In this study, we proposed a novel framework based on Faster RCNN-FPN ar-chitecture for the detection of abnormal cervical cells in cytology images from cancer screening test. We extended the Faster RCNN-FPN model by infusing deformable convolution layers into the feature pyramid network (FPN) to improve scalability. Furthermore, we introduced a global contextual aware module alongside the Region Proposal Network (RPN) to enhance the spatial correlation between the background and the foreground. Extensive experimentations with the proposed deformable and global context aware (DGCA) RCNN were carried out using the cer-vical image dataset of “Digital Human Body" Vision Challenge from the Alibaba Cloud TianChi Company. Performance evaluation based on the mean average precision (mAP) and receiver operating characteristic (ROC) curve has demonstrated considerable advantages of the proposed framework. Particularly, when combined with tagging of the negative image samples using tra-ditional computer-vision techniques, 6-9% increase in mAP has been achieved. The proposed DGCA-RCNN model has potential to become a clinically useful AI tool for automated detection of cervical cancer cells in whole slide images of Pap smear.

The effect of Mg particles on PLA's thermal, chemical, physical, and mechanical properties has been studied. The thermal and physical properties have been studied by differential scanning calorimetry, analysing the stability of the α and α’-crystals of the PLA. A colloidal route was used to introduce Mg particles inside the PLA matrix, ensuring a good dispersion of the particles. Materials with Mg contents from 0 to 10 wt.% have been prepared, with additions of polyethyleneimine (PEI) and polyethylene glycol (PEG). Fourier Transform Infrared Spectroscopy has been used to confirm the influence of Mg, PEI, and PEG on PLA properties. The mechanical properties have been measured with a universal tensile test machine on printed filaments via Fused Filament Fabrication (FFF), which were naturally aged to stable conditions. Filaments with and without a notch were studied to obtain the materials' tensile strength, elastic modulus, and fracture toughness. Different analytical models to explain the results of the PLA-Mg were studied, in which the interface strength of the PLA-Mg composites was calculated.

High-penetration of Distributed Energy Resources (DER) in low voltage distribution grids, mainly photovoltaics (PV), might lead to overvoltage in the point of common coupling. Volt-VAr is one of the common control functions for DER power converters used to enhance the stability and the reliability of the voltage in the distribution system and, thus, fulfilling the network operator requirements. In this study, a centralized algorithm will provide local Volt-VAr control parameters to each PV inverter, based on the electrical grid characteristics where each equipment is installed. Since accurate information of grid characteristics is typically not available, the parametrization of the electrical grid is done using power meter data in DER location and a voltage sensitivity matrix. The algorithm has different optimization modes to both minimize voltage deviation and line current. In order to validate the effectiveness of the algorithm and its deployment in real infrastructure, it has been tested in an experimental setup with PV emulators in a set of 5-day tests. Volt-VAr control algorithm successfully adapted its parameters based on grid topology and PV inverter characteristics, achieving a voltage reduction up to 25% of the allowed voltage deviation.

Fired bricks have shown tremendous potential as a construction material due to their properties. However, their use required some specifications in terms of quality, resistance, and durability. In developing countries, the lack of tools to make test specimens leads to many defects in these brick specimens responsible for low durability and weak precision during mechanical tests and shrinkage. In this study, a simple and traditional method of making test bricks is presented. This simple method allows the production of bricks with the required properties. This method is especially efficient for a firm or semi-soft pastes consistency. The handmade pastes do not stick into the walls of the mold like the case of steel molds and it gives specimens with standard shape, smooth surface, and sharp edges. The resulting fired bricks exhibit high mechanical strength comparable and even better than those of conventional methods.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

The carbonized elastomer-based composites (CECs) possess a number of attractive features in terms of thermomechanical and electromechanical performance, durability in aggressive media and facile net-shape formability, but their relatively low ductility and strength limit their suitability for structural engineering applications. Prospective applications such as structural elements of MEMS can be envisaged, since smaller principal dimensions reduce the susceptibility of components to residual stress accumulation during carbonization, and to brittle fracture in general. We report the results of operando in-SEM study of micro-deformation and fracture behavior of CECs based on NBR elastomeric matrices filled with carbon and silicon carbide. Nanostructured carbon composite materials were manufactured via compounding of elastomeric substance with carbon and SiC fillers using mixing rolling mill, vulcanization, and low-temperature carbonization. Double Edge Notched Tensile (DENT) specimens of vulcanized and carbonized elastomeric composites were subjected to in situ tensile testing in the chamber of the scanning electron microscope (SEM) Tescan Vega 3 using Deben Microtest 1 kN Tensile Stage. The series of acquired SEM images were analyzed by means of Digital Image Correlation (DIC) using Ncorr open source software to map the spatial distribution of strain. These maps were correlated with Finite Element Modelling (FEM) simulations to refine the values of elastic moduli. Besides, the elastic moduli were derived from unloading curve nanoindentation hardness measurements carried out using NanoScan-4D tester and interpreted using the Oliver-Pharr method. Carbonization causes significant increase of elastic moduli from 0.86 ± 0.07 to 14.12 ± 1.20 GPa for the composite with graphite and carbon black fillers. Nanoindentation measurements yield somewhat lower values, namely, 0.25 ± 0.02 GPa and 9.83 ± 1.10 GPa before and after carbonization respectively. The analysis of fractography images suggests that crack initiation, growth and propagation may occur both at the notch stress concentrator and relatively far from the notch. Possible causes of such response are discussed, namely, (1) residual stresses introduced by processing; (2) shape and size of fillers; and (3) the emanation and accumulation of gases in composites during carbonization.

The Medi-test system we developed was motivated by the large number of resources available for the medical domain, as well as the number of tests needed in this field (during and after the medical school) for evaluation, promotion, certification, etc. Generating questions to support learning and user interactivity has been an interesting and dynamic topic in NLP since the availability of e-book curricula and e-learning platforms. Current e-learning platforms offer increased support for student evaluation, with an emphasis in exploiting automation in both test generation and evaluation. In this context, our system is able to evaluate a student’s academic performance for the medical domain. Using as input medical reference texts and supported by a specially designed medical ontology, Medi-test generates different types of questionnaires for Romanian language. The evaluation includes 4 types of questions (multiple-choice, fill in the blanks, true/false and match), can have customizable length and difficulty and can be automatically graded. A recent extension of our system also allows for the generation of tests which include images. We evaluated our system with a local testing team, but also with a set of medicine students, and user satisfaction questionnaires showed that the system can be used to enhance learning.

Colorectal cancer (CRC) is one of the leading cancer-related causes of death in the world. Since the 70s, many countries have adopted different CRC screening programs which has resulted in a decrease in mortality. However, current screening test options still present downsides. The commercialized stool-based tests present high false-positive rates and low sensitivity, which negatively affects the detection of early stage carcinogenesis. The gold standard colonoscopy has low uptake due to its invasiveness and the perception of discomfort and embarrassment that the procedure may bring.In this review, we collected and described the latest data about alternative CRC screening techniques that can overcome these disadvantages. Web of Science and PubMed were employed as search engines for studies reporting on CRC screening tests and future perspectives. The searches generated 555 articles, of which 93 titles were selected. Finally, a total of 50 studies, describing 14 different CRC alternative tests, were included. Among the investigated techniques the main feature that could have an impact on CRC screening perception and uptake was the ease of sample collection. Urine, exhaled breath and blood-based tests promise to achieve good diagnostic performance (sensitivity of 63-100%, 90-95%, 47-97%, respectively) while minimizing stress and discomfort for the patient.

The determination of the non-loading condition of the rail cable shifting (RCS) system, which consists of main cables, hangers and rail cables, is the premise of the girder erection for the long-span suspension bridges. An analytical form-finding analysis model of shifting system is established according to the basic assumptions of flexible cable structures. Herein, the rail cable is discretized into segmental linear cable elements and the main cable is discretized into segmental catenary elements. Moreover, the calculation and analysis equation of each member and their iterative solutions are derived by taking the elastic elongation of the sling into account. In addition, by taking the girder construction of Aizhai suspension bridge as engineering background, a global scale model of the RCS system is designed and manufactured; also the test system and working conditions are established. The comparison between the test results and analytical results shows the presented analytical method is correct and effective. The process is simplified in the analytical method, and the computational results and precision can satisfy the practical engineering requirements. In addition, the proposed method is suitable to apply to the computation analysis of similar structures.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

At-home rapid antigen test (RAT) kits for severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) are valuable public health tools during the present coronavirus disease (COVID-19) pandemic. They provide fast identification of coronavirus infection, which can help to reduce the transmission rates and burden on the healthcare system. However, they have lower sensitivity when compared with the reverse transcription polymerase chain reaction (RT-PCR) tests. One of the reasons for the lower sensitivity is due to the RAT color indicators being indistinct or invisible to the naked eye after the measurements. For this reason, we propose a systematic approach, through which we investigated anonymously provided at-home RAT kit results by using our in-house open source image processing scripts developed for affordable Raspberry Pi computer and Raspberry Pi HQ camera systems (available at https://github.com/kmiikki/ratcv). Therefore, we aimed at minimizing the human-related analysis errors for such kits. We believe that our framework can contribute to reduced the delayed quarantines of infected individuals and spreading of the current infectious disease.

Research Highlights: Data of advanced-age provenance tests were reanalyzed applying a new approach, to directly estimate the growth of populations at their original sites under individually generated future climates. The results reveal surprisingly high resilience potential of fir species. Background and Objectives: The growth and survival of silver fir under future climatic scenarios is insufficiently investigated at the xeric limits. The selective signature of past climate determining the current and projected growth was investigated to analyze the prospects of adaptive silviculture and assisted transfer of silver fir populations, and of the introduction of non-autochthonous species. Materials and Methods: Hargreaves’ climatic moisture deficit was selected to model height responses of adult populations. Climatic transfer distance was used to assess the relative drought stress of populations at the test site, relating these to the past conditions to which the populations had adapted. ClimateEU and ClimateWNA pathway RCP8.5 data served to determine individually past, current, and future moisture deficit conditions. Beside silver fir, other fir species from South Europe and the American Northwest were also tested. Results: Drought tolerance profiles explained the responses of transferred provenances and predicted their future performance and survival. Silver fir displayed significant within-species differentiation regarding drought stress response. Applying the assumed drought tolerance limit of 100mm relative moisture deficit, most of the tested silver fir populations seem to survive their projected climate at their origin until the end of the century. Survival is likely also for transferred Balkan fir species and for grand fir populations, but not for the Mediterranean species. Conclusions: The projections are less dramatic than provided by usual field assessments. Some results contradict generally accepted concepts. The method fills the existing gap between experimentally determined adaptive response and the predictions needed for management decisions. It also underscores the unique potential of provenance tests.

Peptides of hydrolysates of food proteins are an easily digestible source of amino acids necessary for the body to adapt to physical stress. Commercially significant hydrolysates include whey protein, casein, and other animal proteins. Hydrolysates of plant proteins are gaining popularity, but they are less common, then animal ones. Soy protein isolate is promising for obtaining the hydrolysates due to its affordable price and balanced amino acid profile. However, there are no direct studies showing an improvement in the result of physical activity when eating soy protein isolate hydrolysate (SPIH). In this work, for the first time, the study was conducted on the safety and efficacy of SPIH during physical load on model animals (rats). It was shown that the hydrolysate did not lead to pathological changes in the viscera, food intake, and weight of animals did not differ from the control group (animals consumed whey protein). Under physical load rats enteral fed SPIH showed a tendency to adapt more quickly to physical stress than the control group and the group of animals that was fed by free amino acids. The metabolites of animal blood serum were studied by NMR spectroscopy. It was shown that by the 95th minute after feeding in the group of rats receiving SPIH, the difference of proteinogenic amino acids concentrations in blood between individuals was significantly less than in the groups receiving whey protein or a mixture of amino acids. In other words, individual biochemical and physiological characteristics of individuals did not affect the assimilation of amino acids of hydrolysate.

This paper introduces a model-free, "on-the-fly" learning control strategy for arrays of energy converters with adjustable generator damping. The devices are arranged so that they are affected simultaneously by the energy medium. Each device uses a different control strategy, of which at least one has to be the machine learning approach presented in this paper. During operation all energy converters record the absorbed power and control output; the machine learning device gets the data from the converter with the highest power absorption and so learns the best performing control strategy for each state. Consequently, the overall network has a better overall performance than each individual strategy. This concept is evaluated for wave energy converter (WEC) with numerical simulations and experiments with physical scale models in a wave tank. In the first of two numerical simulations, the learnable WEC works in an array with four WECs applying a constant damping factor. In the second simulation, two learnable WECs were learning with each other. It showed that in the first test the WEC was able to absorb as much as the best constant damping WEC, while in the second run it could absorb even slightly more. During the physical model test, the ANN showed its ability to select the better of two possible damping coefficients based on real world input data.

Global malaria epidemiology has changed in the last decade with a substantial increase in cases and death being recorded. Over 90% of global cases and deaths occur in Sub-Saharan Africa (SSA). Tanzania accounts for about 4% of all cases and deaths reported in recent years. It is believed that several factors contribute to the resurgence of malaria, parasite resistance to antimalarials and mosquito resistance to insecticides being at the top of the list. The presence of sub-microscopic infections poses a significant challenge to malaria rapid diagnostic tests (mRDT), particularly in low-endemic areas. Our cross-sectional surveys in Handeni and Moshi, Tanzania assessed the effect of low parasite density on mRDT. A significant difference (P˂0.001) in malaria prevalence by mRDT, light microscopy (LM) and nested polymerase chain reaction (PCR) was found among age groups. In comparison to all other groups, school-age children (5-15 years) had the highest prevalence of malaria. Based on the results of this study, mRDT may miss up to 6% of cases of malaria mainly due to low-density parasitaemia. Routinely used mRDT will likely miss the sub-microscopic parasitemia which will ultimately contribute to the continued spread of malaria and hinder efforts to control and eliminate it.

Neuropsychiatric disorders are globally public-health concern, in which diagnosis might be based on symptoms that often vary across individuals. Schizophrenia is one of the major neuropsychiatric disorders, which may affect millions worldwide. Detection of predictive biomarkers is the most intensively developing approach for the disease. However, the biochemical alterations have not been comprehensively distinguished up to the present time. In addition, there is less confidence of finding a specific biomarker for neuropsychiatric disorders including schizophrenia, but rather a specific characteristic behavioral pattern. Maternal immune activation has been considered to be one of the important factors for the development of neuropsychiatric disorders. Here, the mouse model of neuropsychiatric disorders has been built, in which poly-I:C, sodium dextran sulfate (DSS) and κ-carrageenan (CGN) were used for the maternal immune activation during the pregnancy of individuals. Subsequently, we challenged to link some of biochemical changes of p62 and GLAST in the offspring mice brain to the alteration of several pathological behaviors. Consequently, it has been shown that autophagy might be involved in the development of neuropsychiatric disorders including schizophrenia. To our knowledge, this is the first report of the significant correlation between pathological behavior and the biochemical alterations in neuropsychiatric disorder model animals. The relative ease of conducting these evaluation-tasks would make them useful for testing novel therapeutics designed to ameliorate the symptoms of several psychiatric disorders.

Yaws is a skin debilitating disease caused by Treponema pallidum subspecies pertenue with most cases reported in children. World Health Organization (WHO) aims at total eradication of this disease through mass treatment of suspected cases followed by an intensive follow-up program. However, effective diagnosis is pivotal in the successful implementation of this control program. Recombinase polymerase amplification (RPA), an isothermal nucleic acid amplification technique offers a wider range of differentiation of pathogens including those isolated from chronic skin ulcers with similar characteristics such as Haemophilus ducreyi (H. ducreyi). We have developed a duplex RPA assay for the simultaneous detection of Treponema pallidum (T. pallidum) and H. ducreyi (TPHD-RPA). TPHD-RPA assay demonstrated no cross-reaction with other pathogens and enable detection of T. pallidum and H. ducreyi within 15 minutes at 42 oC. The duplex RPA assay was validated with 49 clinical samples from individuals confirmed to have yaws by serological tests. Compared with commercial multiplex real-time PCR, the TPHD-RPA assay demonstrated 94-95% sensitivity for T. pallidum and H. ducreyi confirmed samples, respectively and 100% specificity. This simple novel TPHD-RPA assay enables the rapid detection of both T. pallidum and H. ducreyi in yaws-like lesions. This test could support the yaws eradication programs by ensuring effective diagnosis as well as enable monitoring of eradication efforts success or failure and planning of follow-up interventions at the community level.

Early identification of fetal abnormalities is a huge challenge for modern obstetrics. Quantitative fluorescent polymerase chain reaction (QF-PCR) has quickly become an effective means of chromosome anomaly detection due to its advantages in terms of timing, manpower and accuracy. The QF-PCR results also make a significant change in clinicians’ attitude to some extent, assisting them providing parents with professional and valuable advice on pregnancy management. In this review, the advantages and drawbacks of QF-PCR will be explored. By reviewing studies published in Vietnamese Medical Journals, we conclude QF-PCR can become a potential screening test in the field of prenatal diagnosis.

Cervical cancer is mostly diagnosed cancer of women worldwide and the second most common cancer among middle-aged women in Bangladesh. Knowledge and perception of women are considered one of the major components of prevention strategy. We carried out this survey to assess the existing knowledge level of students and their perception to the role of vaccination in preventing cervical cancer. The participants were female undergraduate students studying Public Health in a university in Chattogram city of Bangladesh. A total of 275 female students were interviewed through prescribed questionnaire possessing questions on basic information of cervical cancer, its causal agent, risk factors, prevention methods, and vaccination. We marked the responses of participants with zero for wrong answer and one for every correct answer and ranked the knowledge level of students. The mean age of study participants was 20.68 years. In total, 69.1% students possessed poor knowledge whereas, 30.9% had good knowledge. The country of students has significant association with their level of knowledge. Most of the students got information on cervical cancer from traditional media (49.8%) and doctor (30.9%) and the effect of these two sources was statistically significant on the knowledge level of students. Students mostly identified vaccination (21.1%) and Gynecological examination (14.39%) as preventing methods. However, 65.5% of them acknowledge that vaccines cannot prevent this cancer and 33.4% believe in different risks of vaccine. Although students have heard of cervical cancer the overall knowledge was insufficient and perceived negative concepts about cancer vaccine. Therefore, we recommend the initiation of educational programs on basic reproductive health and health seeking behaviour targeting young women to successfully control and prevention of this life-threatening health problem.

Polymethyl methacrylate (PMMA) is a transparent thermoplastic with excellent optical properties, transparent surface, low moisture absorption, tensile and electrical resistance. In this study, the alloy was prepared through PMMA and cycloolefin copolymer (COC) due to some similar properties. The mechanical test showed that properties such as impact resistance, elongation, tensile, and flexural strength decreased by adding COC by up to 20% due to less incompatibility and miscibility, but mentioned properties improved by adding COC 40% due to sub-phase generation. The DSC and DMTA tests showed improvement in the thermal properties of alloys by adding 40% COC. SEM micrographs exhibited a softer surface and more phase elongation of the alloy. Finally, the sample was selected as the optimal sample in terms of mechanical properties irradiated by electron beam, and amplification results showed that a dose of 50 KGY increased the mechanical and thermal properties relatively.

In general, the stone pagoda structures with discontinuous surfaces are vulnerable to lateral forces and are severely damaged by earthquakes. After the Gyeongju earthquake in 2016 and the Pohang earthquake in 2017, the earthquakes damaged numerous stone pagoda structures due to slippage, rotation and the separation of stacked stone. To evaluate seismic resistance of masonry stone pagoda structure, we analyzed the seismic behavior of stone pagoda structure using shaking table test. Shaking frequency, permanent displacement, maximum acceleration, rocking, and sliding were assessed. Responses to simulations of the Bingol, Gyeongju, and Pohang earthquakes based on Korean seismic design standard (KDS 41 17 00) were analyzed for return periods of 1,000 and 2,400 years. We found that the type of stylobate affected the seismic resistance of stone pagoda structure. When the stylobates were stiff, seismic energy was transferred from lower to upper regions of the stone pagoda, which mainly resulted in deformation of the upper region. When the stylobates were weak, earthquake energy was absorbed in the lower regions; this was associated with large stylobate deformations. The lower part of tower body was mainly affected by rocking, because the structural members were slender. The higher part of the stone pagoda was mainly affected by sliding, because the load and contact area decreased with height.

In this study, the corrosion performances of ammonium copper quat (ACQ) and boric acid (BA) wood preservatives were investigated, with micronized copper quat (MCQ) and nano boron (NB) used as reference materials. In the study, Scots pine (Pinus sylvestris L.) wood samples were impregnated according to the full-cell process method with ACQ at 2.4% concentration, BA at 4% and MCQ and NB at 1%. The ACQ- and BA-impregnated samples were then impregnated for a second time using five different water-repellent materials: tall oil, linseed oil, sodium silicate, methyl hydrogen silicone and N'-N- (1, 8-Naphthalyl) hydroxylamine. Polyethylene glycol (PEG) 600 and aluminum sulfate were introduced as single impregnations in the form of homogeneous mixtures with the ACQ and BA. The corrosion properties of the impregnated and control samples, including metal weight loss (MWL) and corrosion depth, were examined. As a result, the MWL values of the ACQ-impregnated samples showed an increase compared to the control group. The MWL values of the MCQ-impregnated samples were lower than those of the samples impregnated with ACQ, whilst the MWL values of the BA-impregnated samples were higher than those of the samples impregnated with NB.

The present work aims to characterize the mechanical behavior of a new composite material for the conservation and development of the vast historical and architectural heritage that is particularly vulnerable to environmental and seismic actions. The new composite consists of natural hydraulic lime (NHL) -based mortar, reinforced by sisal short fibers randomly oriented in the mortar matrix. The NHL-based mortar ensures the chemical-physical compatibility with the original feature of the historical masonry structures (mostly in stone and clay) aiming to pursue both the effectiveness and durability of the intervention. The use of vegetable fibers (i.e. the sisal one) is an exciting challenge for the construction industry since they require a lower degree of industrialization for their processing, and therefore, their costs are also low, as compared to the most common synthetic/metal fibers. Beams of sisal-composite sizing 160x40x40 mm3 with a central notch are tested in three-point bending, aiming to evaluate both their bending strength and fracture energy. Also, tensile tests and compressive tests were performed on the composite samples, while water retention test and slump test were performed on the fresh mix. Finally, the tensile tests on the Sisal strand were carried out to evaluate the tensile strength of both strand and wire. A final comparison with unreinforced mortar specimens shows that the proposed composite ensures great workability and good performances in term of ductility and strength and it can be considered a promising alternative to the classic fiber-reinforcing systems.

In this paper, by extending some results of informational genomics, we present a new randomness test based on the empirical entropy of strings and some properties of repeatability and unrepeatability of substrings of certain lengths. We give the theoretical motivations of our method and some experimental results of its application to a wide class of strings: decimal representations of real numbers, roulette outcomes, logistic maps, linear congruential generators, quantum measurements, natural language texts, and genomes. It will be evident that the evaluation of randomness resulting from our tests does not distinguish among the different sources of randomness (natural, or pseudo-casual).

An accurate understanding of jointed rock mass behavior is important in many applications ranging from deep geological disposal of nuclear waste to deep mining to urban geoengineering projects. The roughness of rock fractures and the matching of the fracture surfaces are the key contributors to the shear strength of rock fractures. In this research, push shear tests with three normal stress levels of 3.6, 6.0, and 8.5 kPa were conducted with two granite samples with artificially induced well-matching tensile fractures with sizes of 500 mm × 250 mm and 1000 mm × 500 mm. The large sample reached on average a -60 % weaker peak shear stress than the medium-sized sample, and a strong negative scale effect was observed in the peak shear strength. The roughness of the surfaces was measured using a profilometer and photogrammetry. The scale-corrected profilometer-based method (JRC) underestimates the peak friction angle for the medium-sized slabs by -27 % for the medium sample and -9 % for the large sample. The photogrammetry-based (Z’2) method produces an estimate with -7% (medium) and +12 % (large) errors. The photogrammetry-based Z’2 is an objective method that consistently produces usable estimates for the JRC and peak friction angle.

The standard edge crush test (ECT) allows to determine the crushing strength of the corrugated cardboard. Unfortunately, this test cannot be used to estimate the compressive stiffness, which is an equally important parameter. It is because, any attempt to determine this parameter using current lab equipment quickly ends in a fiasco. The biggest obstacle is obtaining a reliable measurement of displacements and strains in the corrugated cardboard sample. In this paper, we present a method that not only allows to reliably identify the stiffness in the loaded direction of orthotropy in the corrugated board sample, but also the full orthotropic material stiffness matrix. The proposed method uses two samples: (a) traditional, cut crosswise to the wave direction of the corrugated core, and (b) cut at an angle of 45 degrees. Additionally, in both cases, an optical system with digital image correlation (DIC) is used to measure the displacements and strains on the outer surface of samples. The use of a non-contact measuring system allows to avoid using the measurement of displacements from the crosshead, which is burdened with a large error. Apart from the new experimental configuration, the article also proposes a simple algorithm to quickly characterize all sought stiffness parameters. The obtained results are finally compared with the results obtained in the homogenization procedure of the cross-section of the corrugated board. The results were consistent in both cases.

The silanol activity and trace metal detection methods for chemically bonded silica gels were evaluated in silico. Test compounds with large molecular sizes may demonstrate negative results because of the possibility of indirect hydrogen bonding via short alkyl groups or siloxane of the silica gels. This hypothesis was based on the observation of weak hydrogen bonding energy values similar to those observed in the study of the alkyl group effect on the hydrogen bonding of alkanols. Consequently, smaller molecules may be a better choice for the analysis of bonded-phase quality.

Diabetes mellitus is a widespread chronic metabolic disorder demanding regular blood glucose level surveillance (BGLs). Current invasive techniques, such as finger-prick tests, often result in discomfort for patients, leading to infrequent monitoring and potential health complications. The primary objective of this study was to design a novel, portable, non-invasive system for diabetes detection using breath samples, named as DiabeticSense, an affordable digital health device for early detection, encouraging immediate intervention. The device employed MOSFET-based electrochemical sensors to assess volatile organic compounds in breath samples, whose concentrations differ between diabetic and non-diabetic individuals. The system merged body vital signs with sensor voltages obtained by processing breath sample data to predict diabetic conditions. Our research used readings from 100 patients at a nationally recognised hospital to form the dataset. Data was then processed 10 using a Gradient Boosting Classifier model, and performance was cross-validated. The proposed system attained a promising accuracy of 86.6%, marking an improvement of 20.72% over an existing regression technique. The developed device introduces a non-invasive, cost-effective, and user-friendly solution for preliminary diabetes detection. It has the potential to increase patient adherence to regular monitoring.

Alzheimer’s disease (AD) causes dementia and memory loss in the elderly. Deposits of beta-amyloid peptide and hyperphosphorylated tau protein are present in AD’s brain. A filtrate of Helicobacter pylori’s culture was previously found to induce hyperphosphorylation of tau in vivo, suggesting that bacterial exotoxins could permeate the blood brain barrier and directly induce tau’s phosphorylation. H. pylori, which infects ~60% of the world population and causes gastritis and gastric cancer, produces a pro-inflammatory urease (HPU). Here the neurotoxic potential of HPU was investigated in cultured cells and in rats. SH-SY5Y neuroblastoma cells exposed HPU (50-300 nM) produced reactive oxygen species (ROS) and had an increased [Ca2+]i. HPU-treated BV-2 microglial cells produced ROS, cytokines IL-1β and TNF-α, expressed Iba1 and showed reduced viability, consistent with a neurotoxic effect of HPU. Rats received daily i.p. HPU (5 µg) for 7 days. Hyperphosphorylation of tau at Thr205, Ser199 and Ser396 sites was seen in hippocampal homogenates of treated rats, with no alterations in total tau or GSK-3b levels. HPU was not detected in the brain homogenates. Behavioral tests were performed to assess cognitive impairments. Our findings support previous data suggesting an association between infection by H. pylori and tauopathies such as AD, possibly mediated by its urease.

We have previously reported that a single test measuring oVEMP n10 to 4000Hz stimuli (either bone-conducted vibration (BCV) or air-conducted sound (ACS)) provides a definitive diagnosis of semicircular canal dehiscence (SCD) in 22 CT-verified patients with a sensitivity of 1.0 and specificity of 1.0. Such a single short screening test has great advantages of speed, minimizing testing time and the exposure of patients to stimulation. However some studies of the 4000Hz test for SCD have reported sensitivity and sensitivity values somewhat less that what we reported.

A wide variety of bacteria, fungi and plants can produce bioactive secondary metabolites, which are often referred to as natural products. With the rapid development of DNA sequencing technology and bioinformatics, a large number of putative biosynthetic gene clusters have been reported. However, only a few natural products can be detected when isolated species are grown under conventional laboratory conditions, as most biosynthetic gene clusters are not expressed or are expressed at extremely low levels at these conditions. With the rapid development of synthetic biology, advanced genome mining and modification strategies have been reported, and they provide new opportunities for discovery of natural products. This review discusses advances in recent years that can accelerate the design, build, test, and learn (DBTL) cycle of natural product discovery, and prospects trends and key challenges for future research directions.

Evaluation of the usefulness of [18F]FDG-PET/CT in the short-term follow-up of patients admitted for COVID-19 pneumonia and to explore the association of findings with clinical prognostic markers. Prospective study included 20 patients admitted to hospital with COVID-19 pneumonia between November 2020 and March 2021. Clinical and laboratory test findings were gathered at admission, 48-72h post-admission, and 2-3 months post-discharge. [18F]FDG-PET/CT and respiratory function tests were performed at 2-3 months post-discharge. Lung volumes (TLC), spirometry (FVC, FEV1), lung diffusion capacity for carbon monoxide (DLCO), and respiratory muscle strength were measured. PET/CT images were qualitatively and semi-quantitatively interpreted. Volumetric [18F]FDG-PET/CT results were correlated with laboratory test and respiratory parameters. Eleven [18F]FDG-PET/CT (55%) were positive. The main finding was hypermetabolic lymphade-nopathy in the mediastinum (90.9%). SUVpeak of the target mediastinum lesion was correlated with neutrophil and lymphocyte counts. Eleven (55%) patients had impaired respiratory function, most frequently a reduced DLCO (35%). SUVpeak was positively correlated with %predict-ed-DLCO values. Pulmonary TLG was negatively correlated with %predicted-DLCO and TLC values. In the short-term follow-up of patients hospitalized for COVID-19 pneumonia, [18F]FDG-PET/CT findings revealed significant detectable inflammation in lungs and mediastinal lymph nodes that correlated with pulmonary function impairment in more than half of the patients.

Investigations reporting positive effects of Extracorporeal Shock Wave Therapy (ESWT) on nerve regeneration are limited to the rat sciatic nerve model. The effects of ESWT on muscle-in-vein conduits (MVCs) have also not been investigated yet. This study aimed to evaluate the effects of ESWT after repair of the rat median nerve with either autografts (ANGs) or MVCs. In male Lewis rats, a 7-mm segment of the right median nerve was reconstructed either with an ANG or MVC. For each reconstructive technique, one group of animals received one application of ESWT while the other rats served as controls. Animals were observed for 12 weeks and nerve regeneration was assessed via computerized gait analysis, the grasping test, electrophysiological evaluations and histological quantification of axons, blood vessels and lymphatic vasculature. Here we provide for the first time a comprehensive analysis of ESWT effects on nerve regeneration in a rat model of median nerve injury. Furthermore, this study is among the first reporting the quantification of lymphatic vessels following peripheral nerve injury and reconstruction in vivo. While we found no significant direct positive effects of ESWT on peripheral nerve regeneration, results following nerve repair with MVCs were significantly inferior to those after ANG repair.

Understanding neck pain is an important societal issue. Kinematic data from sensors may help to gain insight on the pathophysiological mechanisms associated with neck pain through a quantitative sensorimotor assessment of one patient. The objective of this study was to evaluate the potential usefulness of artificial intelligence with several Machine Learning (ML) algorithms in assessing neck sensorimotor performance. Angular velocity and acceleration measured by an inertial sensor placed on the forehead during the DidRen laser test in thirty-eight acute and subacute non-specific neck pain (ANSP) patients were compared to forty-two healthy control participants (HCP). Seven supervised ML algorithms were chosen for the predictions. The most informative kinematic features were computed using Sequential Feature Selection methods. The best performing algorithm is the Linear Support Vector Machine with an accuracy of 82% and Area Under Curve of 84%. The best discriminative kinematic feature between ANSP patients and HCP is the first quartile of head pitch angular velocity. This study has shown that supervised ML algorithms could be used to classify ANSP patients and identify discriminatory kinematic features potentially useful for the clinicians in the assessment and monitoring of the neck sensorimotor performance in ANSP patients.

We ascertain the in vitro Benznidazole (BZN) and Nifurtimox (NFX) susceptibility pattern of epimastigotes, trypomastigotes, and amastigotes of 21 T. cruzi strains, from patients, reservoir and triatomine bugs of various geographic origin. Using this panel of isolates, we compute the Epidemiological cut off value (CO_wt). Then, the frequency of the susceptible phenotype (Wild type) towards BZN and nifurtimox (NFX) within this set of strains belonging to 3 discrete typing units (DTUs), TcI, TcII, and TcV was deduced. We have observed that the susceptibility status of individual T. cruzi isolates toward BZN and NFX is related to the genetic background and to underlying factors probably related to the individual life trait history of each strain. Analyzing drug susceptibility in this conceptual framework would offers the possibility to evidence a link between isolates expressing a low susceptibility level (not wild-type) as define by the CO_wt value and none-curative treatment. It will also permit to tract drug-resistant parasites in T. cruzi population.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

Liquefaction risk assessment is critical for the safety and economics of structures. As the soil strata of Ramsar area in north Iran is mostly composed of poorly graded clean sand and the ground water table is found at shallow depths, it is highly susceptible to liquefaction. In this study, a series of isotropic and anisotropic consolidated undrained triaxial tests are performed on reconstituted specimens of Ramsar sand to identify the liquefaction potential of the area. The specimens are consolidated isotropically to simulate the level ground condition, and anisotropically to simulate the soil condition on a slope and/ or under a structure. The various states of soil behavior are studied by preparing specimens at different initial relative densities and applying different levels of effective stress. The critical state soil mechanics approach for identifying the liquefaction susceptibility is adopted and the observed phenomena are further explained in relation to the micro-mechanical behavior. As only four among the 27 conducted tests did not exhibit liquefactive behavior, Ramsar sand can be qualified as strongly susceptible to liquefaction. Furthermore, it is observed that the pore pressure ratio is a good indication of the liquefaction susceptibility

Staphylococcus aureus is a major food-borne pathogen. The ability of S. aureus to produce biofilm is a significant virulence factor triggering its persistence in hostile environments. In this study, we screened a total of 420 different food samples and human hand swabs to detect S. aureus and to determine their biofilm formation ability. Samples analyzed were meat, milk, egg, fish, fast foods, and hand swabs. S. aureus were detected by culturing, staining, biochemical, and PCR. Biofilm formation ability was determined by Congo Red Agar (CRA) plate and Crystal Violet Microtiter Plate (CVMP) tests. The icaA, icaB, icaC, icaD, and bap genes involved in the synthesis of bio-film-forming intracellular adhesion compounds were detected by PCR. About 23.81% (100/420; 95% CI: 14.17-29.98%) samples harbored S. aureus as revealed by detection of the nuc gene. CRA plate revealed 20% of S. aureus isolates as strong biofilm producers, while 69% and 11% as in-termediate and non-biofilm producers, respectively. By the CVMP staining method, 20%, 77%, and 3% of the isolates were found strong, intermediate, and non-biofilm producers. Furthermore, 21% of S. aureus isolates carried at least one biofilm-forming gene, where icaA, icaB, icaC, icaD, and bap genes were detected in 15%, 20%, 7%, 20%, and 10% of the S. aureus isolates, respectively. Bivariate analysis showed high significant correlations (p<0.001) between any of the two adhesion genes of S. aureus isolates. To the best of our knowledge, this is the first study in Bangladesh describing the detection of biofilm-forming S. aureus from foods and hand swabs with molecular-based evidence. Our findings suggest that food samples should be deemed a potential reservoir of biofilm-forming S. aureus that indicates a potential public health significance.

Severe malaria in adults is not well studied in Sahelian Africa. Clinical features and mortality associated with severe Plasmodium falciparum malaria in adult patients hospitalized in Kiffa, southern Mauritania, were analysed. Patients over 15 years old admitted for severe malaria between August 2016 and December 2019 were included in the present retrospective study. The World Health Organization (WHO) criteria were used to define severe malaria. The presenting clinical characteristics and outcome were compared. Of 4266 patients hospitalized during the study period, 573 (13.4%) had a positive rapid diagnostic test for malaria, and 99 (17.3%; mean age, 37.5 years; range 15–79 years; sex-ratio M/F, 2.1) satisfied the criteria for severe malaria. On admission, the following signs and symptoms were observed in more than one-fourth of the patients: fever (98%), impairment of consciousness (81.8%), multiple convulsions (70.7%), cardiovascular collapse (61.6%), respiratory distress (43.4%), severe anaemia ≤ 80 g/L (36.4%), haemoglobinuria (27.3%), and renal failure (25.3%). Patients were treated with parenteral quinine or artemether. Fourteen (14.1%) patients died. Multiple convulsions, respiratory distress, severe anaemia, haemoglobinuria, acute renal failure, jaundice, and abnormal bleeding occurred more frequently (P < 0.05) in deceased patients. Mortality due to severe falciparum malaria is high among adults in southern Mauritania. An adoption of the WHO-recommended first-line treatment for severe malaria, i.e. parenteral artesunate, is required to lower the mortality rate associated with severe malaria.

Coronavirus is a disease caused by a severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) which emerged as a global pandemic in 2019 from Wuhan, China. Since its emergence, it has caused immense suffering to human life, 6.27 million lives have been lost, movement curtailed and social dynamics disrupted. The golden standard for getting samples for SARS-CoV-2 detection is through oral- nasopharyngeal swab, this method of sample collection is invasive and uncomfortable, thus stigmatized the general population, and thereby impeded the progress of controlling the spread through mass testing. Being a contact disease, mechanisms to encourage mass testing is key to reduce the spread. This study thus developed a complimentary sample type to test for SARS-CoV-2, the use of human feces. Fecal samples were collected from 100 asym-symptomatic individuals suspected to be infected with COVID-19, virus RNA was then extracted and profiled through Real Time Polymerase Chain Reaction (RT-qPCR). The antigen rapid diagnostic test revealed high positivity rate of 44%, but the real time polymerase chain reaction results on nasopharyngeal and fecal samples revealed a significant variation, high number of the patients tested positive with stool samples compared to the nasopharyngeal swabs, with 43 and 37%, respectively. SARS-CoV-2 virus was detected in both symptomatic and asymptomatic individuals; however, the symptomatic registered a higher positivity of 25% compared to 20% among the asymptomatic patients. Vaccination only lowered the risk of infection, fully and partially vaccinated lowered the infection level to 10% compared to 20% among the unvaccinated. Finally, gender parity in relation to COVID19 was evaluated, more females (56%) compared to males were recruited in this study, out of which (20; 43.4%) were positive, and 26 (56.6%) were negative based on fecal RT-qPCR outcomes. Based on the outcome of this study, rapid diagnostic test (Ag-RDT) however cheap and or fast does not provide accurate information, moreover, the virus does not stay longer within the Oro-nasopharyngeal region, thus the invalid or negative results, thus use of feces should be adopted as a confirmatory test to ascertain the COVID19 status of an individual.

The testing requirements of the active phased array antennas are very different from those of traditional passive antennas, due to its beam steering capability. Usually, each beam profile of the active phased array needs a separate radiation pattern test, which makes the overall testing time extremely long. Thus the traditional antenna test method can no longer meet the efficiency and cost requirements of new active phased array antennas test. In this paper, a fast test method tailored for phased array antennas is proposed that offers significantly reduced testing time at the expense of slight sacrifice of the accuracy. Using the simulated element pattern in array and ideal port excitation, the beam profile in any direction can be predicted by testing only a certain beam profile. Through theoretical derivation and experiments, the effectiveness of the method is verified, and the testing efficiency of the phased array antenna is demonstrated to be improved by ten times or even more.

This paper reports the effect of as-deposited surface condition on the fatigue strength in an additive manufactured titanium alloy Ti-6Al-4V (WAAM Ti64). First, local stress concentration caused by the surface waviness was quantified by a metrology technique followed by numerical modelling. Fatigue tests were conducted under bending load with the as-deposited surface being under tensile cyclic stress. The applicability of two predictive methods was studied and compared with the fatigue test results. The traditional notch stress method overestimated the fatigue strength by a factor of 1.5 at a given life; the poor agreement with the test is attributed to the crack propagation from the waviness being dominant in the bending test, i.e., the crack initiation stage was short, hence the local stress method is unsuitable. The fracture mechanics approach has delivered good predictions at every applied stress levels. The method treats a waviness trough as an initial crack. This approach is suitable for predicting the fatigue life in materials built by wire based directed energy deposition processes.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

Autonomous unmanned aerial vehicles (UAVs) require highly reliable navigation information. Generally, navigation systems with the inertial navigation system (INS) and global navigation satellite system (GNSS) have been widely used. However, the GNSS is vulnerable to jamming and spoofing. The terrain referenced navigation (TRN) technique can be used to solve this problem. In this study, to obtain reliable navigation information even if a GNSS is not available or the degree of terrain roughness is not determined, we propose a federated filter based INS/GNSS/TRN integrated navigation system. we also introduce a TRN system that combines batch processing and an auxiliary particle filter to ensure stable flight of UAVs even in a long-term GNSS-denied environment. As an altimeter sensor for the TRN system, we use an interferometric radar altimeter (IRA) to obtain reliable navigation accuracy in high altitude flight. In addition, a parallel computing technique with general-purpose computing on graphics processing units (GPGPU) is applied to process a high resolution terrain database and a nonlinear filter in real time on board. Finally, we verify the performance of the proposed system through software-in-the-loop (SIL) tests and captive flight tests in a GNSS unavailable environment.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

To detect aberrant human behaviors from large volume of passive data collected by smartphones in real time, we propose an online anomaly detection method using Hotelling’s T-squared test. The test statistic is a weighted average, with more weight on the between-individual component when there are little data available for the individual and more weight on the within-individual component when the data are adequate. The algorithm takes only O(1) run time in each update and the required memory usage is fixed after a pre-specified number of updates. The performance of the proposed method, in terms of accuracy, sensitivity and specificity, is consistently better than or equal to the offline method that it builds upon depending on the sample size of the individual data.

Background. ADHD is a neurodevelopmental disorder that is accompanied by executive deficits. Objectives. To obtain evidence of the usefulness of the BRIEF-P and to analyse the possible ceiling and floor effect of its scores in the assessment of executive function in preschoolers with signs compatible with a possible diagnosis of ADHD. Methods. Seven articles were selected from 2538 potentially eligible articles from different databases. We included studies assessing samples of individuals with symptoms compatible with ADHD, with age range 2-6 years, published in English or Spanish, during the period 2012-2022. References published in: Science Direct, NCBI (PubMed), ProQuest Education Journals in the last decade. Risk of bias was assessed using the QUADAS-2 questionnaire. The main variables were: age and executive functioning. Conclusions. Executive deficits in early-life individuals with ADHD-compatible symptoms are more extensive than deficits in working memory. BRIEF-P is an instrument that facilitates obtaining a sensitive and discriminative executive profile. It should be used in combination with other neuropsychological performance tests, finding a floor effect in tests associated with warm executive functions and a ceiling effect in cold executive functions. This requires using a variety of tests to assess executive performance in preschoolers with symptoms compatible with ADHD and designing intervention proposals in line with them...

With Direct Laser Writing (DLW) maturing in all aspects as a manufacturing technology a toolset for quality assurance must be developed. In this work we want to introduce a first of its kind test artifact. Test artifacts are standardized 3D models with specific geometric feature to evaluate the performance of writing parameters. Test artifacts are already common in other 3D additive manufacturing technologies e.g. Selective Laser Melting. The test artifact introduced in this work was developed in particular to accommodate 1) the high geometrical resolution of DLW structures and 2) the limited possibilities to examine the resulting structure. Geometric accuracy, surface adhesion as well as confocal raman spectroscopy results were considered when evaluating the design of the test artifact. We will explain the individual features and design considerations of our DLW test artifact. The difference between two slicers, Cura and 3DPoli, and the implications on measured feature sizes and the general shape is quantified. The measured geometries are used to derive a general design guide for a specific combination of photoresist, laser power and scanning speed and to analyse the geometric accuracy of a structure produced using these guidelines.

A sufficient amount of tissue sample is required to perform next-generation sequencing (NGS) with a high success rate, but the majority of patients with advanced non-small-cell lung cancer (NSCLC) are diagnosed with small biopsy specimens. Biopsy samples were collected from 184 patients with bronchoscopically diagnosed NSCLC. The tissue surface area, tumor cell count, and tumor content rate of each biopsy sample were evaluated. The impact of the cut-off criteria for the tissue surface area (≥ 1 mm2) and tumor content rate (≥ 30%) on the success rate of Oncomine Dx Target Test (ODxTT) was evaluated. The mean tissue surface area of the transbronchial biopsies was 1.23 ± 0.85 mm2 when small endobronchial ultrasonography with a guide sheath (EBUS-GS) was used, 2.16 ± 1.49 mm2 with large EBUS-GS, and 1.81 ± 0.75 mm2 with endobronchial biopsy (EBB). The proportion of samples with a tissue surface area of ≥ 1 mm2 was 48.8% for small EBUS-GS, 79.2% for large EBUS-GS, and 78.6% for EBB. Sixty-nine patients underwent ODxTT. The success rate of DNA sequencing was 84.1% and that of RNA sequencing was 92.7% over all patients. The success rate of DNA (RNA) sequencing was 57.1% (71.4%) for small EBUS-GS (n = 14), 93.4% (96.9%) for large EBUS-GS (n = 32), 62.5% (100%) for EBB (n = 8), and 100% (100%) for endobronchial ultrasound-guided transbronchial needle aspiration (EBUS-TBNA) (n = 15). Regardless of the device used, a tissue surface area of ≥ 1 mm2 is adequate for samples to be tested with NGS.

Nowadays, the presence of pathogen-specific antibodies in the blood is widely controlled by a serodiagnostic technique based on the lateral flow immunoassay (LFIA). However, its common one-stage format with an antigen immobilized in the binding zone of a test strip and a nanodis-persed label conjugated with immunoglobulin-binding proteins is associated with risks of very low analytical signals. It is caused by the presence of non-specific immunoglobulins in very large excess to the target antibodies in the tested samples thus decreasing their binding with the detected labels. In this study, the first stage of the immunochromatographic serodiagnosis was carried out in its traditional format using a conjugate of gold nanoparticles with staphylococcal immunoglobulin-binding protein A and an antigen immobilized on a working membrane. At the second stage, a labeled immunoglobulin-binding protein was added, which enhanced the coloration of the bound immune complexes. The use of two separated steps, binding of specific antibodies, and further coloration of the formed complexes allowed a significant reducing the influence of non-specific immunoglobulins on the assay results. The proposed approach was ap-plied for the serodiagnosis using a recombinant RBD protein of SARS-CoV-2. As a result, an in-crease in the intensity of test zone coloration by more than two orders of magnitude was demonstrated, which enabled to significantly reduce false-negative results. When testing a panel of 16 positive and 8 negative serum samples, the diagnostic sensitivity of the LFIA was 62.5% for the common format and 100% for the enhanced format; the diagnostic specificity of both variants was 100%.

Burying and burrowing are promising rodent-typical behaviors to model neuropsychiatric symptoms (NPS). However, the original tests could be insufficient to conclude which NPS are modeled. Here, we propose methodological modifications such as the two-zone configuration and dual analysis in the Marble Burying Test (MB). Also, a new Brief Burrowing Test (BB), a 20 min brief version of the Deacon’s Burrowing Test (DB). We comprehensively studied these behaviors in 12-month-old male and female mice with normal and Alzheimer’s disease (AD)-pathological aging. The results: 1) confirm our precedent report of sexual dimorphism, with enhanced burying in male 3xTg-AD mice; 2) describe for the first time burrowing behavior in 3xTg-AD mice and its sex dependence; 3) regardless of the pattern, MB and BB reflected a goal-directed rather than an indiscriminate digging; 4) using the MB and BB to model anxiety-like behavior it’s not recommended; 5) burying and burrowing represent a repetitive rather than a stereotyped-like or perseverative behavior. In addition: 1) burying and burrowing behavioral patterns are alike, connected by several correlations; 2) the two-zones configuration is a useful tool to assess the intentionality of the burying and burrowing behaviors and to perform a more accurate screening of the NPS modeled by them.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

The construction of random fillings from the excavation of medium hardness rocks, with high particle sizes, presents limitations in compaction control. This research applies new control techniques with revised test procedures in the construction of the random fillings core, which constitutes the main part of the embankment, with the bigger volume and provides the geotechnical stability to the infrastructure. The maximum layer thickness researched was 800mm. As there are many types of rocks, this research is applied to metamorphic slates. Quality control has been carried out by applying new research associated with the revision of wheel impression test, topographic settlements and plate bearing test (PBT). A statistical analysis of the core of 16 slate random fillings has been carried out, with a total of 2250 in situ determination of density and moisture content, 75 wheel impression tests, 75 topographic settlement control and 75 PBT. The strong associations found between different tests have allowed to simplify the quality control.

Since 2015, outbreaks of foot-and-mouth disease (FMD) in the Middle East have been caused by a new emerging viral lineage, A/ASIA/G-VII. In-vitro vaccine matching data indicated that this virus poorly matched (low r1-value) with vaccines that were being used in the region as well as most other commercially available vaccines. The aim of this study was to assess the performance of two candidate vaccines against challenge with a representative field virus from the A/ASIA/G-VII lineage. The results from an initial full dose protection study provided encouraging data for the A/MAY/97 vaccine, while the A22/IRQ/64 vaccine only protected 2/7 vaccinated animals. In view of these promising results, this vaccine was tested in a potency test (PD50) experiment in which 5 cattle were vaccinated with a full dose, 5 cattle with a 1/3 dose and 5 cattle with a 1/9 dose of vaccine. Vaccines were prepared as would be done during an emergency vaccination campaign using a double oil emulsion adjuvant. At 21 days post vaccination these vaccinated cattle and 3 control cattle were subsequently challenged intradermolingually with a field isolate from the A/ASIA/G-VII lineage. All cattle from the full vaccine dose, 4 cattle from the 1/3 vaccine dose and 2 cattle from the 1/9 vaccine dose were clinically protected against challenge with FMDV A/ASIA/G-VII, resulting in a heterologous potency of 6.5 PD50/dose. These data support previous studies showing that a high potency emergency vaccine can protect against clinical disease when challenged with a heterologous strain of the same serotype. Not only the r1-value of the vaccine, but also the homologous potency of a vaccine should be taken into account when advising vaccines to control an outbreak.

Objectives: This paper presents a statistical review of modelling simulations for frequency and sensitivity of COVID-19 testing paradigms. Methods: We performed a review of preprints and published articles on PubMed from January 1, 2020 – March 1, 2021 using the search terms “COVID screening testing”, “COVID testing frequency”, “COVID testing frequency screening” and “SARS-CoV-2 testing frequency”.Results: Several authors’ conclusions support the claim that test frequency and test sensitivity both play a role in reducing SARS-CoV-2 transmission. We highlight the interplay between frequency of testing, test sensitivity and the speed at which test results are available in our review. Conclusions: Evidence suggests that sensitivity and frequency of testing both play a part in decreasing transmission of disease. We conclude that, overall, test sensitivity plays less of a role in reducing disease transmission in a population compared to the frequency of testing and how quickly test results are available.

This paper describes a new optimization methodology of testing vector sets reduction for testing of soft-processor cores and their individual blocks. The deterministic test vectors both for whole core and its individual blocks are investigated that significantly reduce the testing time and amount of test data that needs to be stored on the tester memory. The processor executes an assembler program which together with determined testing vectors ex-ercise its functionality. The new BIST methodology applicable at industrial testing of processor cores, diagnostics and dynamic reconfiguration of FPGA is proposed. This novel methodology combined with dynamic reconfiguration of FPGAs can be profitable applied for missions-critical i.e. FPGAs operate in space, or other difficult condition where are explore on radiation. Experimental results demonstrate that the proposed approach reduces many times testing time.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this work is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Residual dizziness after a liberating maneuver is often referred to by patients as a more disabling set of symptoms than the positional vertigo itself. This situation seems to involve more than half of subjects with labyrintholithiasis. The authors examine the hypothesis according to which residual dizziness involves subjects with labyrintholithiasis on the basis of otoconia.

The multi-material design and the adaptability of a modern process chain require joining connections with specifically adjustable mechanical, thermal, chemical or electrical properties, whereby previous considerations have focused primarily on the mechanical properties. With clinching, the multitude of possible combinations of requirements, materials and component or joint geometry makes it impossible to determine these joint properties empirically. As a result of the established and empirically based procedure, no model exists to date that considers all questions of joinability, i.e. the materials (suitability for joining), the design (joining safety) and the production (joining possibility) and allows a calculation of the achievable properties. It is therefore necessary to describe the physical properties of the joint as a function of the three bonding mechanisms force closure, form closure and material closure in relation to the application. This approach enables the illustration of the relationships along the causal chain "joint requirement - binding mechanism - joining parameters". In this way the adaptability of the mechanical joining technology can be improved. A geometric comparison is made using metallographic cross sections, of clinched joints of the combination of aluminum and steel. The torsional testing of the rotationally symmetric clinching points for detection of the mechanical stress state are qualified as examination method and technological test. By measuring the electrical resistance in the base material, in the clinch joint and during the production cycle (after clinching, before precipitation hardening and after precipitation hardening), this change in the stress state can also be detected.

Immense challenges arise in the Quality Assurance area due to contemporary development in Internet of Things (IoT) technology. Current issues are mainly related to test coverage, test diversity, IoT Stability, Use of Cellular Networks in IoTs, IoT Devices updates, Security, Data Integration, and interoperability. In this paper, we present all those issues with suggestions for tackling those issues.

The work consisted in identifying possible effects from heavy metals (HMs) pollution due to waste disposal activities in three potentially polluted sites located in Basilicata (Italy), where a release of pollutants with values over the thresholds allowed by the Italian legislation was detected. The potential variations in the physiological efficiency of vegetation have been analyzed through the multitemporal processing of satellite images. In detail, Landsat 5 Thematic Mapper (TM) and Landsat 8 Operational Land Imager (OLI) images were used to calculate the Normalized Difference Vegetation Index (NDVI) trend over the years. Then, the multitemporal trends were analyzed using the median of Theil-Sen, a non-parametric estimator particularly suitable for the treatment of remote sensing data, being able to minimize the outlier effects due to exogenous factors. Finally, the subsequent application of the Mann-Kendall test on the trends identified by Theil-Sen slope allowed the evaluation of trends significance and, therefore, the areas characterized by the effects of contamination on vegetation. The application of the procedure to the three survey sites led to the exclusion of the presence of significant effects of HMs contamination on the vegetation surrounding the sites during the years of waste disposal activities.

The reference method for cefiderocol antimicrobial susceptibility testing is broth microdilution (BMD) with iron-depleted-Mueller-Hinton (ID-MH) medium, whereas breakpoints recommended for disk diffusion (DD) are based on MH-agar plates. We aimed to compare the performance of the commercial BMD tests ComASP (Liofilchem) and UMIC (Bruker), DD and E-test using MH- and ID-MH-agar plates with the reference BMD method using 100 carbapenem-resistant-A. baumannii isolates. Standard BMD was performed according to the EUCAST guidelines, DD and E-test were carried out using two commercial MH-agar plates (bioMérieux and Liofilchem) and an in-house ID-MH-agar plate, while ComASP and UMIC were performed according to the manufacturer’s guidelines. DD performed with the ID-MH-agar plates led to a higher categorical agreement (CA, 95.1%) with standard BMD and fewer categorization errors compared to the commercial MH-agar plates (CA bioMérieux 91.1%, Liofilchem 89.2%). E-test on ID-MH-agar plates exhibited a significantly higher essential agreement (EA, 75%) with standard BMD compared to the two MH-agar plates (EA bioMérieux 57%, Liofilchem 44%), and showed a higher performance in detecting high-level resistance than ComASP and UMIC (mean log2 difference with standard BMD for resistant isolates of 0.5, 2.83 and 2.08, respectively). In conclusion, DD and E-test on ID-MH-agar plates exhibit a higher diagnostic performance than on MH-agar plates and the commercial BMD methods. Therefore, we recommend using ID-MH-agar plates for cefiderocol susceptibility testing of A. baumannii.

Nowadays, energy saving is considered a key issue worldwide, as it brings a variety of benefits: reducing greenhouse gas emissions, reducing demand for energy imports, and lowering costs on a household and economy-wide level. Researchers and building designers are looking to optimize building efficiency by means of new energy technologies. Changes in existing buildings can also be made to reduce energy consumption and costs. These may include the usage of new heat transfer fluids based on nanofluids. In this work, an extended experimental campaign (from February 2020 to March 2021) has been carried out on an educational building in the Campus of University of Salento, Lecce – Italy, in order to evaluate the increase in performance of the HVAC system, due to the usage of a nanofluid. The results show that, under optimal operating conditions, plant performance improves more than 10%, with average daily peaks of about 15%.

The use of smartphones, coupled with different sensors, makes it an attractive solution for measuring different physical and physiological features, allowing for the monitoring of various parameters and even identifying some diseases. The BITalino device allows the use of different sensors, including Electroencephalography (EEG) and Electrocardiography (ECG) sensors, to study different health parameters. With these devices, the acquisition of signals is straightforward, and it is possible to connect them using a Bluetooth connection. With the acquired data, it is possible to measure parameters such as calculating the QRS complex and its variation with ECG data to control the individual's heartbeat. Similarly, by using the EEG sensor one could analyze the individual's brain activity and frequency. The purpose of this paper is to present a method for recognition of the diseases related to ECG and EEG data, with sensors available in off-the-shelf mobile devices and sensors connected to a BITalino device. The data were collected during the elderly's experiences, performing the Timed-Up and Go test, and the different diseases found in the sample in the study. The data were analyzed, and the following features were extracted from the ECG, including heart rate, heart rate variability, the average QRS interval, the average R-R interval, and the average R-S interval, and the EEG, including frequency and variability. Finally, the diseases are correlated with different parameters, proving that there are relations between the individuals and the different health conditions.

This work is concerned with the existence and uniqueness of boundary value problems defined on semi-infinite intervals. These kinds of problems seldom admit exactly known solutions and, therefore, the theoretical information on their well-posedness is essential before attempting to derive an approximate solution by analytical or numerical means. Our utmost contribution in this context is the definition of a numerical test for investigating the existence and uniqueness of solutions of boundary problems defined on semi-infinite intervals. The main result is given by a theorem relating the existence and uniqueness question to the number of real zeros of a function implicitly defined within the formulation of the iterative transformation method. As a consequence, we can investigate the existence and uniqueness of solutions by studying the behaviour of that function. Within such a context the numerical test is illustrated by two examples where we find meaningful numerical results.

Combining Matrix-Assisted Laser Desorption/Ionization Time-of-Flight (MALDI-TOF) spectra data and artificial intelligence (AI) has been introduced for rapid prediction on antibiotic susceptibility test (AST) of S. aureus. Based on the AI predictive probability, the cases with probabilities between low and high cut-offs are defined as “grey zone”. We aimed to investigate the underlying reasons of unconfident (grey zone) or wrong predictive AST. A total 479 S. aureus isolates were collected, analyzed by MALDI-TOF, and AST prediction, standard AST were obtained in a tertiary medical center. The predictions were categorized into the correct prediction group, wrong prediction group, and grey zone group. We analyzed the association between the predictive results and the demographic data, spectral data, and strain types. For MRSA, larger cefoxitin zone size was found in the wrong prediction group. MLST of the MRSA isolates in the grey zone group revealed that uncommon strain types composed 80%. Amid MSSA isolates in the grey zone group, the majority (60%) was composed of over 10 different strain types. In predicting AST based on MALDI-TOF AI, uncommon strains and high diversity would contribute to suboptimal predictive performance.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

The experiments described in this research article were designed to test the effect of rare variants into genomic prediction in dairy cattle. Common polymorphisms are able to explain only a small proportion of the underlying genetic variation of complex phenotypes. Variants representing functional mutations with large effects on complex phenotypes are expected to be rare due to natural (humans) or artificial (livestock) selection pressure. Therefore, it is important to check whether the use of rare variants could increase the accuracy of ranking of animals by providing the tool for more precise differentiation among the bulls with high additive genetic merit. The goal of our study was to verify whether including rare variants in a genomic selection model allows for a more accurate description of the additive genetic background of traits under selection in dairy cattle. We used the linear mixed model for comparison SNP estimates for Holstein-Friesian cattle of the two data sets – a set containing only single nucleotide polymorphisms defined by minor allele frequency ≥ 0.01, which is routinely used in the Polish genomic evaluation system (46,216 SNPs), and a set containing SNPs selected based only on the call rate (54,378 SNPs). Based on the SNP estimates we also calculated DGV and GEBV and compared them between both data sets. In all the analyses we used production, fertility, conformation and udder health traits. We also assessed the time required for the two most computationally demanding components of genomic selection: preparing genotype data, and estimation of SNP effects between those two data sets. The results of our study indicated that the analysis including rare variants resulted in changes in the individual ranking of the top 100 male and female candidates, but had no effect on the outcome of the quality of EBV prediction as expressed by the Interbull validation test.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

The present paper investigates the influence of the specimen size of EN-AW6082 wrought aluminium alloy subjected to very high cycle fatigue (VHCF) tests. The hourglass specimens were tested under fully reversed loading condition, up to 10^9 cycles, by means of the ultrasonic fatigue testing machine developed by Italsigma® (Italy). Three specimens groups were considered, with a diameter in the middle cross-section ranging from 3 mm up to 12 mm. The stress field in the specimens was determined numerically and by strain gauge measurements in correspondence of the cross-section surface. The dispersion of experimental results has been accounted for, and data are reported in P-S-N diagrams. The decrease in fatigue resistance with increasing specimen size is evident. Theoretical explanation for the observed specimen-size effect is provided, based on Fractal Geometry concepts, allowing to obtain scale independent P-S*-N curves. The fatigue life expectation in the VHCF regime of the EN-AW6082 aluminium alloy full-scale components is rather overestimated if it is assessed only from standard small specimens of 3 mm in diameter. Experimental tests carried out on larger specimen, and a proper extrapolation, are required to assure safe structural design.

The change in the value of the breaking energy is discussed here for selected steel grades used in building structures after subjecting the samples made of them to episodes of heating in the steady-state heating regime and then cooling in a simulated fire conditions. These changes were recorded based on the instrumented Charpy impact tests, in relation to the material initial state. The S355J2+N, 1H18N9T steels and also X2CrNiMoN22-5-3 duplex steel were selected for detailed analysis. The fire conditions were modelled experimentally by heating the samples and then keeping them for a specified time at a constant temperature of: 600°C (first series) and 800°C (second series), respectively. Two alternative cooling variants were investigated in the experiment: slow cooling of the samples in the furnace, simulating the natural fire progress, without any external extinguishing action, and cooling them in water mist simulating an extinguishing action by a fire brigade. The temperature of the tested samples was set at the level -20oC and alternatively at the level + 20oC. The conducted analysis is aimed at assessing the risk of sudden, catastrophic fracture of load-bearing structure made of steel degraded as a result of a fire previously occurred with different development scenarios.

In this study, the focus is on the drop test simulation of an MR (Magnetorheological) damper-based main landing gear (MRMLG), aiming to explore multi-degree-of-freedom (DOF) dynamic models during aircraft landing. Three different 6-DOF dynamic models are proposed in this work and their drop performances are compared with results achieved one of commercial softwares. The proposed models include a nonlinear aircraft model (NLAM), a linearized approximated aircraft model (LAAM) linearizing from the nonlinear equations of motion in NLAM, and a fully approximated aircraft model (FAAM) which linearizes the MRMLG's strut force model. In order to evaluate drop performance of the aircraft landing gear system with MR dampers, a 7-DOF aircraft model incorporating the nonlinear MRMLG is formulated using RecurDyn. The principal comparative param-eters are the coefficient of determination (R2) for system response of each model with Re-curDyn model and root mean square error (RMSE) which is the ensembles of CG dis-placement data for each model. In addition, the ensemble of time series data is created for diverse drop scenarios, providing valuable insights into the performance of the proposed drop test models of the aircraft landing gear system featuring MR dampers.

Hazelnut is a widespread nut species, especially in Europe, that can be consumed raw or roasted, due to its pleasant taste and nutritional properties. Despite the renowned beneficial properties, hazelnuts contain several proteins capable of inducing food allergy in sensitized individuals such as Cor a 2 (profilin), Cor a 8 (lipid transfer protein), Cor a 9 (11S seed storage globulin, legumin-like) and Cor a 11 (7S seed storage globulin, vicilin-like). In the present paper we investigated the effectiveness of autoclave based treatments in decreasing the allergic potential of hazelnut as also assessed by submitting the treated material to in vivo skin prick test and to in vitro immunoblot analysis with sera of allergic individuals exposed to the treated food material. This preliminary analysis shows that autoclave treatment, preceded by hydration and/or followed by drying, seems to be a promising approach and appears to be effective in reducing the allergenicity of hazelnut in most patients, probably due to the denaturation of most major and minor allergenic proteins. This work will open to the opportunity to produce, in perspective, hypoallergenic hazelnut derivatives tolerated by the allergic subjects.

Purpose: To investigate trabeculopuncture (TP) for predicting the outcome of ab interno trabeculectomy (AIT). AIT is an effective, low-risk procedure for open angle glaucoma. Despite widespread utilization, it fails in patients with an unidentified distal outflow resistance. Methods: We bisected 81 enucleated porcine eyes and perfused them for 72 hours. They were assigned to two groups: trial (n=42) and control (n=39). Intraocular pressure (IOP) was measured continuously. At 24 hours, four YAG-laser trabeculopunctures on the nasal trabecular meshwork were performed, followed by a 180° AIT at the same site at 48 hours. Eyes were divided into TP and AIT responders and non-responders; the proportion of TP responders between both AIT groups was compared. Results: Both post-TP and post-AIT IOPs were lower than baseline IOP (p=0.015 and p<0.01, respectively). The success rates of TP and AIT were 69% and 85.7%, respectively. The proportion of TP responders among AIT responders was greater than that of AIT non-responders (p<0.01). Sensitivity and specificity values of TP as predictive test for AIT success were 77.7% and 83.3%, respectively. The positive and negative predictive values were 96.6% and 38.5%, respectively. Conclusion: A 10% reduction in IOP after TP can be used as predictor for the success (>20% IOP decrease) of 180° AIT in porcine eyes.

In recent years, many studies have highlighted the consistent finding of amoxicillin in waters destined for wastewater treatment plants, in addition to superficial waters of rivers and lakes in both Europe and North America. In this paper, the amoxicillin degradation pathway was investigated by simulating the chlorination process normally used in a wastewater treatment plant to reduce similar emerging pollutants at three different pH values. The structures of 16 isolated degradation byproducts (DPs), one of which was isolated for the first time, were separated on a C-18 column via a gradient HPLC method. Then, combining mass spectrometry (MALDI-MS/TOF) and nuclear magnetic resonance, we compared commercial standards and justified a proposed formation mechanism beginning from the parent drug. Microbial growth inhibition bioassays with Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were performed to determine the potential loss of antibacterial activity in isolated degradation byproducts. An increase of antibacterial activity in the DPs was observed compared to the parent compound.

Over the past decade, China has witnessed fast-paced technological advancements in the media industry, as well as major shifts in the health agenda portrayed in the media. Therefore, a key starting point when discussing health communication lies in whether media attention and public attention towards health issues are structurally aligned, and to what extent the news media guide public attention. Based on data mined from 73,060 sets of the Baidu Search Index and Media Index on 20 terms covering different types of cancer from 2011 to 2020, the Granger test demonstrates that, in the last decade, public attention and media attention towards cancer in China has gone through two distinct phases. During the first phase, 2011-2015, Chinese news media still held the key in transferring the salience of issues on most cancer types to the public. In the second phase, from 2016-2020, public attention towards cancer has gradually diverged from media coverage, mirroring the imbalance and mismatch between the demand of active public and the supply of cancer information from news media. This study provides an overview of the dynamic transition on cancer issues in China over a ten-year span, along with descriptive results on public and media attention towards specific cancer types.