In this work, TiO₂ QDs modifed NiO nanosheets was employed to imporve the room-temperature NO₂ sensing properties of NiO. The gas-sensing studies showed that the response of nanocomposites with the optimal ratio to 60 ppm NO₂ was nearly 10 times larger than that of bare NiO, exhibiting potential application in gas-sensing. Considering the commonly reported immature mechanism that the effective charge transfer between two phases contribute to enhanced sensitivity, QDs sensitization mechanism was further detailed by designing a seirs of contrast experiments. First, the important role of QDs size effect was revealed by comparing a little enhanced sensitivity of TiO₂ particle-modified NiO with largely enhanced senstivity of TiO₂ QDs-NiO. Second, and more important, the direct evidence of heterointerface charge transfer efficiency was detailed by extracted interface bond (Ti-O-Ni) using XPS peak fitting. We hope this work can provide guideline to design more QDs-modified nanocomposites with the higher sensitivty for practical application.

The relativistic Doppler effect comes from the fact that observers in different inertial reference frames experience space and time differently, while the speed of light remains always the same. Consequently, a wave packet of light exhibits different frequencies, wavelengths, and amplitudes. In this paper, we present a local approach to the relativistic Doppler effect based on relativity, spatial and time translational symmetries, and energy conservation. Afterward, we investigate the implications of the relativistic Doppler effect for the quantum state transformations of wave packets of light and show that a local photon is a local photon at the same point in the spacetime diagram in all inertial frames.

The aim of this document is to provide practical guidance on the choice of target difference used in the sample size calculation of a randomised controlled trial (RCT). Guidance is provided with a definitive trial, one that seeks to provide a useful answer, in mind and not those of a more exploratory nature. The term “target difference” is taken throughout to refer to the difference that is used in the sample size calculation (the one that the study formally “targets”). Please see the glossary for definitions and clarification with regards other relevant concepts. In order to address the specification of the target difference, it is appropriate, and to some degree necessary, to touch on related statistical aspects of conducting a sample size calculation. Generally the discussion of other aspects and more technical details is kept to a minimum, with more technical aspects covered in the appendices and referencing of relevant sources provided for further reading.The main body of this guidance assumes a standard RCT design is used; formally, this can be described as a two-arm parallel-group superiority trial. Most RCTs test for superiority of the interventions, that is, whether or not one of the interventions is superior to the other (See Box 1 for a formal definition of superiority, and of the two most common alternative approaches). Some common alternative trial designs are considered in Appendix 3. Additionally, it is assumed in the main body of the text that the conventional (Neyman-Pearson) approach to the sample size calculation of an RCT is being used. Other approaches (Bayesian, precision and value of information) are briefly considered in Appendix 2 with reference to the specification of the target difference.

Nanopeening treatment was applied to the AISI 420 steel to decrease its sensitivity to the tribocorrosion damage. Microstructural investigation highlighted that the Nanopeening treatment led to a high plastic deformation and nanostructured surface layer with 110 µm depth. . In order to study the combined effect of corrosion and mechanical wear, tribocorrosion tests were performed on non–treated and nanopeened samples in boric acid and lithium hydroxide solution, considering both continuous and intermittent sliding. It was found that the AISI 420 steel is sensitive the synergism between mechanical friction and electrochemical corrosion with a domination of abrasive wear. Adhesive wear was also detected in the wear track. Indeed, the mechanical wear was pronounced under intermittent sliding because of hard wear debris generation from the repassivated layer during rotating time. The Nanopeening treatment led to enhance mechanical performance and corrosion properties. Such improvement could be explained by the high plastic deformation resulting in the nano-structuration of grains and increasing hardness of AISI 420 steel.

The out-of-equilibrium dynamics of many body systems has recently received a burst of interest, also due to experimental implementations. The dynamics of both observables, such as magnetization and susceptibilities, and quantum information related quantities, such as concurrence and entanglement entropy, have been investigated under different protocols bringing the system out of equilibrium. In this paper we focus on the entanglement entropy dynamics under a sinusoidal drive of the tranverse magnetic field in the 1D quantum Ising model. We find that the area and the volume law of the entanglement entropy coexist under periodic drive for an initial non-critical ground state. Furthermore, starting from a critical ground state, the entanglement entropy exhibits finite size scaling even under such a periodic drive. This critical-like behaviour of the out-of-equilibrium driven state can persist for arbitrarily long time, provided that the entanglement entropy is evaluated on increasingly subsytem sizes, whereas for smaller sizes a volume law holds. Finally, we give an interpretation of the simultaneous occurrence of critical and non-critical behaviour in terms of the propagation of Floquet quasi-particles.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

In this study, the model proposed by Yang et al. to generalize the stress–strain model for unconfined concrete with consideration of the size effect is expanded. Sim et al.’s compressive strength model that is based on the function of specimen width and aspect ratio was used for the maximum stress. In addition, a strain at the maximum stress was formulated as a function of compressive strength by considering the size effect using the regression analysis of datasets compiled from a wide variety of specimens. The descending branch after the peak stress was formulated with consideration of less dissipated area of fracture energy with the increase in specimen width and aspect ratio in the compression damage zone (CDZ) model. The key parameter for the slope of the descending branch was formulated as a function of specimen width and aspect ratio, concrete density, and compressive strength of concrete considering the size effect. Consequently, a rational stress–strain model for unconfined concrete was proposed. This model explains the trends of the peak stress and strain at the peak stress to decrease and the slope of the descending branch to increase, as the specimen width and aspect ratio increase. The proposed model agrees well with the test results, irrespective of the compressive strength of concrete, concrete type, specimen width and aspect ratio. In particular, the proposed model for the stress–strain curve rationally considered the effect of decreasing peak stress and increasing the descending branch slope, with the increase in specimen width and aspect ratio.

In this work, we report the magnetocaloric effect (MCE) in a quantum dot corresponding to an electron interacting with an antidot, under the effect of an Aharonov-Bohm flux subjected to a parabolic confinement potential. We use the Bogachek and Landman model, which additionally allows the study of quantum dots with Fock-Darwin energy levels for vanishing antidot radius and flux. We find that the Aharonov-Bohm flux (AB-flux) strongly controls the oscillatory behaviour of the MCE, thus acting as a control parameter for the cooling or heating of the magnetocaloric effect. We propose a way to detect AB-flux by measuring temperature differences.

We continue to analyze basic constraints on human's decision making from the viewpoint of quantum measurement theory (QMT). As has been found, the conventional QMT based on the projection postulate cannot account for combination of the question order effect (QOE) and the response replicability effect (RRE). This was an alarm signal for quantum-like modeling of decision making. Recently, it was shown that this objection to quantum-like modeling can be removed on the basis of the general QMT based on quantum instruments. In the present paper we analyse the problem of combination of QOE, RRE, and the famous QQ-equality (QQE). This equality was derived by Busemeyer and Wang and it was shown (in the joint paper with Solloway and Shiffrin) that statistical data from many social opinion polls satisfies it. Now, we construct quantum instruments satisfying QOE, RRE, and QQE. The general features of our approach are formalized with postulates which generalize {\it Wang-Busemeyer} postulates for quantum-like modeling of decision making. Moreover, we show that our model closely reproduces the statistics of the famous Clinton-Gore Poll data with a prior belief state independent of the question order. This model successfully removes the order effect from the data to determine the genuine distribution of the opinions in the Poll. The paper also provides a psychologist-friendly introduction to the theory of quantum instruments - the most general mathematical framework for quantum measurements. We hope that this theory will attract attention of psychologists and will stimulate further applications.

The fast spread of COVID-19 constitutes a worldwide challenge to the public health, educational, and trade systems, affecting the overall wellbeing of human societies. The high transmission and mortality rates of this virus, and the unavailability of a vaccine or treatment, resulted in the decision of multiple governments to enact measures of social distancing. Thus, it is of general interest to consider the validity of the proposal for keeping a social distancing of at least 2 m from other persons to avoid the spread of COVID-19. The exposure to the bioaerosol can result in the deposition of the pathogen in the respiratory tract of the host causing disease and an immunological response. In the atmospheric context, the work evaluates the effect of aerodynamic diameter (size) of particles in carrying RNA copies of the novel coronavirus. A SARS-CoV-2 carrier person talking, sneezing, or coughing at distance of 2 m can still provide a pathogenic bioaerosol load with submicron particles that remain viable in air for up to 3 hours for exposure of healthy persons near and far from the source in a stagnant environment. The deposited bioaerosol creates contaminated surfaces, which if touched can act as a path to introduce the pathogen by mouth, nose, or eyes and cause disease.

Thermal shape memory polymers (SMPs) find increasing applications in biology and medicine due to their promising potential for improved biocompatibility. In such applications, the inevitable penetration of small molecules from the ambient fluid into the polymer influences the shape recovery process and often leads to a reduction of the temperature, at which shape recovery takes place. We show here via molecular dynamics simulations that the size of additive molecules plays a key role for this process. While the effect of concentration on the recovery rate is monotonic in the investigated range, a non-monotonic dependence on the size of additive molecules emerges at temperatures close to the glass transition. This work thus identifies the additives’ size to be a qualitatively novel parameter for switching the recovery process in polymer-based shape memory materials.

The reinforcement of concrete by using polyolefin fibres may be considered in structural design to meet the requirements of the applicable code rules. In order to achieve a reliable use of such a composite material, use of full-scale real structures is needed. The conversion of lab testing data into real practice properties is challenging and significantly influenced by various aspects, among which the size effect is a key one. Given that the available literature does not report coinciding conclusions about such an effect on quasi-brittle materials reinforced with fibres, further research is justified. Therefore, this work studies the behaviour of notched beams with three proportional sizes by using self-compacting polyolefin reinforced concrete with a fibre volume fraction of 1.1%. Flexural testing was carried out according to the standard EN-14651, with the results revealing the existence of the size effect. In addition, a reduction of the residual strength identified in the larger specimens was observed in fracture surfaces with equal fibre content.

The cosmological constant problem is examined by taking an Einstein--scalar with a Higgs-type potential and scrutinizing the infrared structure induced by finite temperature effects. A variant optimal perturbation theory is implemented in the recently proposed quantum-gravitational framework. The optimized renormalized mass, i.e., the renormalized mass determined by the variant optimal perturbation theory, of the scalar field turns out to be on the order of the temperature. This shifts the cosmological constant problem to compatibility of the consequent perturbative analysis. The compatibility is guaranteed essentially by renormalization group invariance of physical quantities. We point out the resummation behind the invariance.

Silver nanoparticles (AgNPs) have been demonstrated to restrain bacterial growth while maintaining the minimal risk in development of bacterial resistance and human cell toxicity that conventional silver compounds exhibit. Several physical and chemical methods have been reported to synthesize AgNPs. However, these methods are expensive and involve heavy chemical reduction agents. An alternative approach to produce AgNPs in a cost-effective and environmentally friendly way employs a biological pathway using various plant extracts to reduce metal ions. The size control issue and the stability of nanoparticles remain some of the latest challenges in such methods. In this study, we used two different concentrations of fresh leaf extract of the plant Arbutus Unedo (LEA) as a reducing and stabilizing agent to produce two size variations of AgNPs. UV-Vis spectroscopy, Dynamic Light Scattering, Transmission Electron Microscopy and zeta potential were applied for the characterization of AgNPs. Both AgNP variations were evaluated for their antibacterial efficacy against the gram-negative species Escherichia coli and Pseudomonas aeruginosa, as well as the gram-positive species Bacillus subtilis and Staphylococcus epidermidis. Although significant differences have been achieved in the nanoparticles’ size by varying the plant extract concentration during synthesis, the antibacterial effect was almost similar.

In this paper, we investigate the Hawking radiation process by using the quantum tunneling phenomenon of massive spin-1 (W-bosons) and spin-0 particles from (2+1) dimensional Black Hoke with quintessential and magnetic field. For this purpose, using Hamilton-Jacobi ansatz, we apply the WKB approximation to the field equations of massive charged vector particles. We get the required tunneling rate of radiated particles and obtain their corresponding Hawking temperature $T_h$. In order to study the quantum gravity effects, we utilize the generalized Proca and Klein-Gordan equations incorporating the generalized uncertainty principle (GUP) and recover the accompanying quantum corrected temperature $T'_{h}$.

In this paper, we scrutinize the axiomatic system of effect algebras which is given by D. J. Foulis and M.K. Bennett in the paper Effect Algebras and Unsharp Quantum Logics. We prove that this axiomatic system consists of independent axioms. To do this, we construct some models to indicate the indepence of each axiom. Therefore none of these axioms can be reduced when constructing any effect algebra. As a result, any algebra is an effect algebra if and only if it verifies (E1)-(E4) axioms.

This study aimed to decrease the particle size of ginseng by roasting and cryogenic milling to increase its water solubility and physiological activity. The samples were roasted for different times (9–21 min) and generated in different sizes (10–50, and > 50 μm). All roasted samples revealed significantly smaller particle sizes than did non-roasted samples based on Sauter mean diameter (D [3,2], p < 0.05). Further, the particle sizes of roasted samples decreased till roasting up to 15 min. In terms of the water solubility index (WSI), antioxidant activity, total polyphenol content (TPC), and total polysaccharides according to particle size, 10-20 μm-sized samples showed the highest values when compared with >50 μm-sized samples. Based on roasting time, WSI values of all samples roasted for up to 15 min were higher than those of the control (not roasted) (p < 0.05). Antioxidant activity and TPC also increased with increasing roasting time. Total polysaccharide content was the highest upon roasting for 15 min except for the 10-20 μm sample. Ginsenoside content of roasted samples >20 μm size was higher than that of the control (not roasted) except after 15 min of roasting. Therefore, roasting and cryogenic milling are effective in producing ginseng root powder.

In this paper, using the two integers that describe the stationary 2-dimensional wave and the charge quantization along with the balance between the Lorentz force and electrical force, we succeed in deriving the fractional quantum Hall effect and the integer quantum Hall effect; we find that the latter exists as a special case of the former. Moreover, using the derived expression describing the fractional quantum Hall effect, a relationship between the plateau in the resistivity of the sample and the applied magnetic field is obtained. The findings of this model agree well with experimental measurements. Because the two integers that describe the stationary 2-dimensional wave and the charge quantization along with the force balance have concrete physical meanings in this work, we could provide a clear picture of the origin of both the integer quantum Hall effect and the fractional quantum Hall effect.

In our previous works we have proposed design equations that can predict with reasonable accuracy the transition point from homogeneous to heterogeneous regime as well as the gas holdup and the mean Sauter diameter at the homogeneous regime. The validity of the proposed correlations was checked with data obtained using different geometrical configurations and several Newtonian and non-Newtonian liquids as well as the addition of surfactants. However, in all the experiments the gas phase was atmospheric air. This work investigates the effect of gas phase properties by conducting experiments employing various gases (i.e., air, CO₂, He) that cover a wide range of physical property values. Experiments revealed that only the use of low-density gas (He) has a measurable effect on bubble column performance. More precisely, when the low-density gas (He) is employed, the transition point shifts to higher gas flow rates and the gas holdup decreases, a fact attributed to the lower momentum force exerted by the gas. In view of the new data, the proposed correlations have been slightly modified to include the effect of gas phase properties and it is found that they can predict the aforementioned quantities with an accuracy of ±15%. It has been also proved that CFD simulations are an accurate means for assessing the flow characteristics inside a bubble column.

Exploring the effect of the sample size on the estimation accuracy of airborne LiDAR forest attributes in a large-scale area can help in optimizing the technical application scheme of operational ALS-based large-scale forest stand inventories. In our study, sample datasets composed of different sample plots were constructed by repeated sampling from 1003 sample plots in a subtropical study area covering 2376 × 103 km2. Sixteen multiplicative power models were built in each forest type consisting of four forest attributes. Through these models, the variations of standard deviation (SD) and coefficient of variation (CV) of R2 and rRMSE of forest attribute estimation models for different quantity levels of sample plots were also analyzed. The results showed that, first, when the sample size increased from 30 to the top limit, the SD of the forest attributes and LiDAR variables showed a decreasing trend. Second, as the sample size increased, the rRMSE of the 16 forest attribute estimation models gradually decreased, while the R2 gradually increased. Third, when the sample size was small, both the SD of R2 and rRMSE of the models were large, and the SD of R2 and rRMSE gradually decreased as the sample size increased. In 50 models conducted for each attribute at the same sample size, for the mean standard deviations of forest attributes, the ten best performing models were lower than those of the total 50 models, and the worst ten models were the opposite. When the sample size increased, the accuracy of each forest attribute estimation model for each forest type gradually improved. The variation of forest attributes and the LiDAR variable of the construction model are critical factors that affect the model’s accuracy. To efficiently apply airborne LiDAR in order to survey large-scale subtropical forest resources, the sample size of the Chinese fir forest, pine forest, eucalyptus forest, and broad-leaved forest should be 110, 80, 85, and 70, respectively.

Blast charge initiation procedures have a significant impact on both mining safety and production rates. In this study, the inventory benefit of an electric initiation system was investigated to assess its influence on both fragmentation and blast-induced damages. The Wipfrag software's was used to examine the size distribution and productivity of 12 small-scale blasts initiated by both non-electric and electric detonators. All blast rounds was initiated with plain type of electric and NONEL detonators. The average burden, spacing, stemming length, and charge weight were, respectively, 0.85 m, 1.10 m, 0.66m, and 1.1kg. The results showed that the mesh through which 80% of the blast fragments will pass for the electric blast is smaller than the mesh through which the material products from the NONEL blast will pass. The results also demonstrate that the generated blast-induced ground vibration (PPV) from all blast rounds for electric blast varies from 0.4–1.2 mm/s and 80–105dB, while that for non-electric blast ranges from 0.05–0.2mm/s and 72–95dB. As a result, the electric blast initiation technique was found to produce good fragmentation, with a higher percentage of optimum fragment sizes on spec than non-electrically initiated blasts.

Landslides are serious geological hazards that become a disaster worldwide, causing a large number of casualties and economic losses every year. There are many factors affecting landslide susceptibility, such as rainfall, soil and slope. Each of them has an important role in the process of slope losing stability. In this paper, the effects of rainfall intensity, rainfall pattern, slope gradient and soil type on landslide susceptibility are studied. In the process of rainfall-induced landslide, the relevant physical quantities of soil changes continuously. Their values and processes are closely related to the time of landslide occurrence. Hence, the variation of soil volumetric water content, matrix suction, pore water pressure and total stress throughout the rainfall are measured. As the results, soil type, slope gradient and rainfall intensity have a large influence on landslide susceptibility. The occurrence of landslides has a prerequisite that the slope is greater than or equal to 15°. The rainfall intensity needs to be not less than 80 mm/h. The difference of rainfall pattern also affects the landslide susceptibility. The rainfall pattern with rainfall intensity peak at the later stage is more likely to induce landslide. Coarser soils with gravels are prone to landslides when other conditions are the same. Steeper slopes, stronger rainfall, and coarser soils can all increase the amount of sediment yield.

In this work, we report the caloric effect for an electronic system of the antidot type, modeled by combining a repulsive and attractive potential (parabolic confinement). In this system, we consider the action of a perpendicular external magnetic field and the possibility of having an Aharonov-Bohm flux (AB-flux) generated by a current passing through a solenoid placed inside the forbidden zone for the electron. The energy levels are obtained analytically, and the model is known as the Bogachek and Landman model. We propose to control the caloric response of the system by varying only the AB-flux, finding that in the absence of an external magnetic field, the maximization of the effect always occurs at the same AB-flux intensity independent of the temperature while fixing the external magnetic field at a non-zero value breaks this symmetry and changes the point where the caloric phenomenon is maximized and is different depending on the temperature to which the process is carried. Due to the great diversity in technological applications that have antidots in electronics, the possibility of controlling their thermal response just by varying the intensity of the internal current inside the solenoid can be a platform of interest for experimental studies.

tructural and superconducting properties of high quality Niobium nanofilms with different thicknesses are investigated on silicon oxide and sapphire substrates. The role played by the different substrates and the superconducting properties of the Nb films are discussed based on the defectivity of the films and on the presence of an interfacial oxide layer between the Nb film and the substrate. The X-ray absorption spectroscopy is employed to uncover the structure of the interfacial layer. We show that this interfacial layer leads to a strong proximity effect, specially in films deposited on a SiO2 substrate, altering the superconducting properties of the Nb films. Our results establish that the critical temperature is determined by an interplay between quantum-size effects, due to the reduction of the Nb film thicknesses, and proximity effects.

Loess is a special soil with high water sensitivity, which covers a large area in northwest China. Cracks are prone to generate in loess under the arid and semi-arid climate, which will provide the preferential channel for water and reduce the mechanical properties of soils. It is of great significance to understand the evolution characteristics and mechanisms of the cracks in loess areas. At present, the researches on cracks in soils are mainly concentrated in the characteristics of different cracking patterns. However, the spacing cracks are mostly discussed in materials like rock and concrete, rather than soils. The cracking characteristics and mechanisms of spacing cracks in loess is still inadequate. In this research, the drying tests of loess are carried out with different sizes of specimens. The parameters of spacing cracks and local strain distributions of the loess samples are obtained via PCAS and DIC methods during desiccation, respectively. The cracking modes, space cracking laws like insertion and saturation of spacing cracks are revealed. Finally, the size effect on the characteristics of spacing cracks is verified with a discrete element software MatDEM.

Size effect on plain concrete specimens is well known and can be correctly captured when performing numerical simulations by using a well characterised softening function, but in the case of fibre reinforced concrete this is not directly applicable, since an only diagram cannot capture the material behaviour on elements with different size due to dependence of the orientation factor of the fibres with the size of the specimen. In previous works, the use of a trilinear softening diagram proved to be very convenient for reproducing fracture of polyolefin fibre reinforced concrete elements, but only if it is previously adapted for each specimen size. In this work, a predictive methodology is used to reproduce fracture of polyolefin fibre reinforced concrete specimens of different sizes under three-point bending. Fracture is reproduced by means of a well known embedded cohesive model, with a trilinear softening function that is defined specifically for each specimen size. The fundamental points of these softening functions are defined a priori by using empirical expressions proposed in past works, based on an extensive experimental background. Therefore, the numerical results are obtained in a predictive manner, and then compared with a previous experimental campaign, showing that this approach properly captures the size effect, although some values of the fundamental points in the trilinear diagram could be defined more accurately.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Live fuel moisture content (LFMC) influences fire activity at landscape scale and fire behavior in laboratory experiments. However, field evidences linking LFMC to fire behavior are very limited despite numerous field experiments. In the present study, we reanalyze a shrubland fire dataset with a special focus on LFMC to explain this counterintuitive outcome. We found that this controversy might result from three reasons. First, the range of experimental LFMC data was too moist to reveal significant effect with the widespread exponential or power functions. Indeed, LFMC exhibited a strong effect below 100%, but marginal above this threshold, contrary to these functions. Second, we found that the LFMC significance was unlikely when the size of the dataset was smaller than 40. Finally, a complementary analysis suggested that 10 to 15% of random measurement error in variables could lead to an underestimation by 30 % of the LFMC effect. The effect of LFMC in field experiments is thus stronger than previously reported in the range prevailing during the actual French fire season and in accordance with observations at different scales. This highlights the need to improve our understanding of the relationship between LFMC and fire behavior to refine fire danger predictions.

This study aims to model grinding of a Polish slag and evaluate the particle size distributions of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e. temperature, curing and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin-Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multi fractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

Background: Benveniste’s biology experiments suggested the existence of molecular-like effects without molecules (“memory of water”). In this article, it is proposed that these disputed experiments could have been the consequence of a previously unnoticed and non-conventional experimenter effect. Methods: A probabilistic modelling is built in order to describe an elementary laboratory experiment. A biological system is modelled with two possible states (“resting” and “activated”) and exposed to two experimental conditions labelled “control” and “test”, but both biologically inactive. The modelling takes into account not only the biological system, but also the experimenters. In addition, an outsider standpoint is adopted to describe the experimental situation. Results: A classical approach suggests that, after experiment completion, the “control” and “test” labels of biologically-inactive conditions should be both associated with “resting” state (i.e. no significant relationship between labels and system states). However, if the fluctuations of the biological system are also considered, a quantum-like relationship emerges and connects labels and system states (analogous to a biological “effect” without molecules). Conclusions: No hypotheses about water properties or other exotic explanations are needed to describe Benveniste’s experiments, including their unusual features. This modelling could be extended to other experimental situations in biology, medicine and psychology.

A novel gas-phase electrocatalytic system based on a low-temperature proton exchange membrane (Sterion) was developed for the gas phase electrocatalytic conversion of CO2 to liquid fuels. This system achieved gas-phase electrocatalytic reduction of CO2 at low temperatures (below 90 ºC) over a Cu cathode by using water electrolysis-derived protons generated in-situ on an IrO2 anode. Three Cu-based cathodes with varying metal particle sizes were prepared by supporting this metal on an activated carbon at three loadings (50, 20, and 10 wt%; 50%Cu-AC, 20%Cu-AC, and 10%Cu-AC, respectively). The cathodes were characterized by N2 adsorption–desorption, temperature-programmed reduction (TPR), and X-ray diffraction (XRD) whereas their performance towards the electrocatalytic conversion of CO2 was subsequently studied. The membrane electrode assembly (MEA) containing the cathode with the largest Cu particle size (50%Cu-AC, 40 nm) showed the highest CO2 electrocatalytic activity per mole of Cu, with methyl formate being the main product. This higher electrocatalytic activity was attributed to the lower Cu–CO bonding strength over large Cu particles. Different product distributions were obtained over 20%Cu-AC and 10%Cu-AC, with acetaldehyde and methanol being the main reaction products, respectively. The CO2 consumption rate increased with the applied current and the reaction temperature.

The bimodal grain-size distribution 0.9KNbO₃-0.1BaTiO₃ ceramics, with a typical perovskite structure in tetragonal phase at room temperature, were successfully prepared by an induced abnormal grain growth (IAGG) method at a relatively low sintering temperature. In this bimodal grain-sized distribution structure, the extra-large grains (about 10‒50 μm) were evolved from the micron-sized filler powders and the fine grains (about 0.05‒0.35 μm) were derived from the sol precursor matrix. The 0.9KNbO₃-0.1BaTiO₃ ceramics exhibit relaxor-like behavior with the diffused phase transition near room temperature, and confirmed by the existence of the polar nanodomain regions (PNRs) using the HRTEM images. The large room-temperature electrocaloric (EC) effect was found, characterized by an adiabatic temperature drop of 1.5 K, an isothermal entropy change of 2.48 J kg^-1 K^-1, and high EC strengths of ïDT/DEï = 1.50×10^-6 KmV^-1 and DS/DE = 2.48×10^-6 Jmkg^-1K^-1V^-1directly measured under E = 1.0 MV/m. These excellent ECEs demonstrate that this simple IAGG method is highly appreciated for synthesizing high-performance EC materials for efficient cooling devices.

Evidence-based medicine (EBM) is in crisis, in part due to bad methods, which are understood as misuse of statistics that is considered correct in itself. This article exposes two related common misconceptions in statistics, the effect size (ES) based on correlation (CBES) and a misconception of contingency tables (MCT). CBES is a fallacy based on misunderstanding of correlation and ES and confusion with 2 × 2 tables, which makes no distinction between gross crosstabs (GCTs) and contingency tables (CTs). This leads to misapplication of Pearson’s Phi, designed for CTs, to GCTs and confusion of the resulting gross Pearson Phi, or mean-square effect half-size, with the implied Pearson mean square contingency coefficient. Generalizing this binary fallacy to continuous data and the correlation in general (Pearson’s r) resulted in flawed equations directly expressing ES in terms of the correlation coefficient, which is impossible without including covariance, so these equations and the whole CBES concept are fundamentally wrong. MCT is a series of related misconceptions due to confusion with 2 × 2 tables and misapplication of related statistics. The misconceptions are threatening because most of the findings from contingency tables, including CBES-based meta-analyses, can be misleading. Problems arising from these fallacies are discussed and the necessary changes to the corpus of statistics are proposed resolving the problem of correlation and ES in paired binary data. Since exposing these fallacies casts doubt on the reliability of the statistical foundations of EBM in general, we urgently need to revise them.

The effect of filling velocity on positive macrosegregations in large size steel ingots was studied. Macrosegregation and macro-/micro-structure were characterized on the hot-tops and a portion of the upper section of two ingots. The measurements revealed that segregation features in the two ingots varied as a function of the alloying elements, and that the severity of positive macrosegregation in the casting body was reduced when the filling rate was increased. It was also found that at the higher filling rate, grain morphologies in the first solidified zones of the ingot changed from columnar to equiaxe, and secondary dendrite arm spacing (SDAS) became slightly smaller in the intermediate and final solidified zones. The experimental findings were analyzed in the framework of diffusion and convection controlled solidification, as well as liquid metal flow theories. The solute dependence of segregation features was related to the difference in solid-liquid partition coefficient and diffusion capability of each element in the liquid iron. Calculation of Reynolds numbers (Re) during the filling process, for both ingots, showed that higher filling velocity caused more instable movement of the liquid metal in the initial solidification stage, resulting in the modification of grain morphology, as well as accelerated solidification rate.

During the last decades the quantitative description of electrical and magnetotransport properties of solid-state materials has been a remarkable challenge in materials science. Recently, the discovery of a novel class of materials, the topological semimetals, has led to a growing interest for the full understanding of their magnetotransport properties. In this review, the strong interplay among topology, band structure and carrier mobility in recently discovered high carriers mobility topological semimetals is discussed and their effect on their magnetotransport properties is outlined. The huge magnetoresistance effect, especially in the Hall transverse configuration, and a new version of a three-dimensional quantum Hall effect observed in high-mobility Weyl and Dirac semimetals are reviewed. The design of novel quantum sensors based on solid-state semimetals is also encouraged.

We calculate energies of shallow donors confined in a rolled-up quantum well in the presence of the electric field by solving numerically the Schrödinger equation in natural curvilinear coordinates. It is found that the curves of density of states (DOS) are very sensitive to the variation of the donor position, the geometry of the spiral and the applied electric field value. Novel results for dependencies of donor’s dipole moment and its polarizability on the electric field strength and its orientation, for different donor positions are presented. Also, we found that anisotropic Stark effect of the first order provides in this structure a dependency of the polarizability on the external electric field in a spike-like shape, giving rise to a sharp variation of the dipole moment.

In the present work, three different atmospheric plasma sprayed (APS) alumina coatings were fabricated using three fused and crushed alumina powders of different particle size fine, medium and coarse. The influence of the particle size on thermal properties and micro-structural features of the produced coating were investigated by thermal insulation test and detailed image analysis technique, respectively. The analyzed micro-structural features include the total porosity, pore size (fine, medium, and large) and cracks. All types of cracks were considered in calculations as voids and were evaluated according to their sizes as pores. All spray parameters except the particle size were fixed throughout the spraying process. The results revealed that the fine starting powder has produced the densest coating with the lowest total porosity and that the total porosity increases with an increasing particle size. This was expected as powders of smaller particle size will reach a higher in-flight temperature and velocity than powders of bigger particle sizes as long as the same spray parameters are applied. However, a detailed image analysis investigation on the three produced coatings showed that the fraction of fine pores and cracks versus the total porosity is substantially higher in coatings produced by using fine starting powders than those produced using medium and coarse powders. In this work, a connection between the thermal insulation and the porosity fraction, which includes fine pores and cracks, was revealed.

Tree growth is under the combined influence of abiotic and biotic factors. Trees with different sizes may respond differently to these factors, implying that tree heterogeneity in tree size may also modulate the overall growth trend. To test this hypothesis, we focused on the radial growth trends of natural subalpine forests on the Tibetan Plateau. We first extended the iterative growth model (IGM) to the tree-ring scale (IGMR) to test the applicability of the generalized metabolic growth theory to tree growth. As predicted by the IGMR, the radial growth of trees at the aggregate scale is constrained by a unimodal pattern. Using the IGMR, we reconstructed the historical best growth trajectory (HBGT) of trees within the same community based on the tree with the largest radius and/or longest age in the community. From the average difference between the HBGT and the current radial growth rate of trees with different sizes, we constructed an indicator that can measure the overall variation in tree radial growth. Based on this indicator, we found a negative effect of tree size heterogeneity on the overall variability of tree growth across elevations. Further analysis also revealed that the radial growth rate of trees on the Tibetan Plateau has increased significantly compared to the past, where growing season average temperature and annual minimum temperature were negatively and positively correlated with tree growth below and above the treeline, respectively. Our study not only confirmed that the overall variability of tree growth depends on tree size heterogeneity but also proposed an indicator that reveals net changes in tree radial growth rate relative to the past. These theoretical advances facilitate the understanding of changes in the extent of subalpine forests.

Talbot effect is a self-imaging or lensless imaging phenomenon of a periodic grating illuminated by a collimated light beam at regular distances from the grating. Research on the Talbot effect has recently made significant strides thanks to the quick development of optical superlattices. The emergence of various applications of this effect in fields such as optics, acoustics, X-ray, plasmonics, and information processing has led to the increasing importance of obtaining a Talbot carpet with the use of different structures. In this paper, we investigate the Talbot effect that originates from the tunneling effect between an ensemble of vertically coupled cylindrical quantum dots (QDs). The Talbot carpet can be manipulated by changing the parameters of the QD system. In the current paper, two modified Pöschl-Teller potentials were used to model the QDs ensemble. The exciton’s lifetime and tunneling time’s dependence on the first QD’s potential half-width is found for a fixed value of the external electric field. The nonlinear changes in the refractive index and absorption spectrum dependent on the tunneling effect are obtained. Afterward, the Talbot carpet formation is investigated, particularly the dependences of the formed periodic wavefront’s visibility on medium length, coupling field’s strength, and tunneling parameter. Finally, we have observed the intensity distribution of the diffraction field at Talbot half-distance.

Time evolution of the quantum correlation of the hybrid qubit-qutrit system in multilocal and global dephasing under the effect of a classical noises environment is presented. We considered the qutrit in z direction and the qubit x direction. In addition, our system presents two configurations: the different and the common environment and our discussion involves three types of noises: A Static Noise (SN), Random Telegraph Noise (RTN) and Ornstein- Uhlenbeck noise (OU). By using the density matrix approach to determine the evolution of the state of the system, the found that the static noise is fatal for the quantum entanglement, the quantum correlation and for RTN and OU noises the quantum entanglement, the quantum correlation decreases monotonically with a sufficiently long time. Therefore, we can say that, entanglement and the quantum correlation are more robust to the noise precisely those Random telegraph noise and Ornstein-Uhlenbeck noise.

The effect of the communication channel size on the transport and subsequent detection of chemical messengers is investigated on millimetric and micrometric channels. The transport of the information carriers, being characterized by an advective and a diffusive contribution, was simulated by varying the flow velocity and the diffusion coefficient. Then, to evaluate the information quality, the Intersymbol Interference (ISI) between two consecutive signals at a specific release delay was estimated. This allowed us to verify that operating under micrometric channel conditions has a larger flow velocity range to obtain completely separated successive signals and smaller release delays can be used between signals. The theoretical results were confirmed by developing a prototype molecular communication platform operating under microfluidic conditions, which enables communication through fluorescent nanoparticles, namely Carbon Quantum Dots (CQDs).

We have detected a large Nernst effect in the CDW state of the multiband organic metal α−(BEDT−TT)2KHg(SCN)4. We find that there exists a significant gradient of charge relaxation processes that can generate a sizeable contribution adding especially to the transverse thermoelectric signal. Apart from the phonon drag, the energy relaxation processes governing the electron-phonon interactions and the momentum relaxation processes governing the charge mobility of the q1D group of carriers have a significant role in observing the large Nernst signal in the CDW state. The emphasised momentum relaxation dynamics in the low field CDW state is a clear indicator of a significant carrier mobility that can lead to the largest Nernst signal in this state. The momentum relaxation is reduced with increasing angle and magnetic field, i.e., in the high field CDW state which is reflected in the smaller Nernst effect amplitude. In this case only the phonon drag and electron-phonon interactions are contributing to the transverse thermoelectric signal. Our findings advance and change the previous observations on the complex properties of this organic metal.

The Casimir effect can either work over very short distances or at very low temperatures. At the cosmic scale, we naturally deal with long distances, but at the same time, we encounter extraordinarily low temperatures, namely the CMB (Cosmic Microwave Background) tem- perature. Recently, there has been increased interest in the Casimir effect and its implications in cosmology. Here, we briefly demonstrate that the luminosity and radiation pressure of the CMB is mathematical identical to a theoretical Casimir effect within the Hubble sphere, or actually our solution seems to be valid for any Schwarzschild black hole. The Casimir effect forevery Schwarzschild black hole is identical. This also include the Hubble sphere if we treat it as a Schwarzschild black hole that is related to increased interest in black hole cosmology.

Recently perovskite solar cells have been paying attention of researchers. This comes from their high efficiency and stability. In this work, the change of some Optical and Electrical Properties of BaxFe(1-x)TiO4 thin films due to the change of the nanocrystal spacing and size were studied. A simple theoretical model based on the string theory was utilized to explain some of these empirical relations. The empirical results obtained indicated that an increase in the efficiency of the nano solar cell requires the energy gap to be narrow. Decreasing the nanocrystal size and spacing caused the energy gap to become narrower. The energy gap decreases also upon increasing the absorption coefficient and decreasing the transmission. This also requires increasing the conductivity and the magnetic permeability. The increase of the nanocrystal spacing decreases the absorption coefficient, electrical conductivity, and magnetic permeability, while it causes the transmission to increase. All these changes are explained using a simple string model beside Newton's laws. The capability of the string theory to explain this Nano quantum behavior comes from the fact that the string theory, like quantum theory, recognizes both the particle and the wave nature of the Nano system.

The manipulation of participant allocation in randomized controlled trials to achieve equal groups sizes may introduce allocation bias potentially leading to larger treatment effect estimates. This study aimed to estimate the proportion of nursing trials that have precisely equal group sizes and examine if there was an association with trial outcome. Data were extracted from a sample of 148 randomized controlled trials published in nursing science journals in 2017. One hundred trials (68%) had precisely equal group sizes. Respectively, a positive outcome was reported in 70% and 58% of trials with equal/unequal groups. Trials from Asia were more likely to have equal group sizes than those from the rest of the world. Most trials reported a sample size calculation (n=105, 71%). In a third of trials (n=36, 34%), the number of participants recruited precisely matched the requirement of the sample size calculation; this was significantly more common in studies with equal group sizes. The high number of nursing trials with equal groups may suggest nurses con-ducting clinical trials are manipulating participant allocation to ensure equal group size increasing the risk of bias.

Introduction: The purposes of this study were to seek for overall ratio (OR) and anterior ratio (AR) patients data in normal occlusion and Angle’s malocclusion studies, and to assess if such results support Bolton’s standards as general references. Methods: Pubmed, Medline, CENTRAL and Scholar databases were searched up to February 2018 (CRD42018088438). Gray literature was explored through OpenGray. Non-randomized clinical studies, published in English and assessing Bolton’s OR and AR in normal occlusion and Angle’s malocclusion groups (Class I, Class II, Class II division 1, Class 2 division 2, Class III) patients were included. OR and AR means and standard deviations (SD) were collected. Potential covariates (study design, publication year, country where the study was conducted, number of cases, gender, mesiodistal measurement method, and calibration method) were also extracted. The National Health Heart Lung, and Blood Institute’s Quality Assessment Tool for Observational Cohort and Cross-Sectional Studies was used to assess each included studies quality. Pairwise Random-Effects and Multilevel Bayesian Network Meta-Analyses were used to synthesize available data. Results: Fifty-two observational studies were included (8872 participants; male/females 2674/3272; 16 studies lacked gender information). For normal occlusion, global pooled estimates for OR and AR means were 91.74% (95% CI: 91.37-92.10) and 78.24% (95% CI: 77.85-78.63), respectively. We could identify on Angle’s Class III patients meaningful OR and AR mean deviations from normal occlusion (0.89, 95% credible interval [CrI], 0.66-1.12, and 0.66, 95% CrI, 0.38-0.94, respectively), while on Class I patients we found a meaningful mean deviation from normal occlusion only for OR (0.25, 95% CrI, 0.03-0.47). Concerning gender impact, male patients presented higher OR (0.30, 95% CI 0.00-0.59) and AR (0.41, 95% CI 0.00-0.83) mean values than females in Class I. Conclusions: The results show that global pooled OR and AR mean values for normal occlusion patients are slightly above Bolton’s original values. Class I, for OR mean values, and Class III, for both OR and AR, are proportionally larger than normal occlusion patients. Gender had almost no impact on teeth mesiodistal proportion.

We consider the quantum thermodynamic origin of the gravitational force of matter by applying the spacetime entanglement entropy and the Unruh effect originating from vacuum quantum fluctuations. By analyzing both the local thermal equilibrium and quasi-static processes of a system, we may get both the magnitude and direction of Newton's gravitational force in our theoretical model. Our work shows the possibility that the elusive Unruh effect has already shown its manifestation through gravitational force.

The phenomenal mathematical efficiency of quantum field theories in modern high-speed information and communication systems has a very simple explanation from the point of view of common sense and higher mathematical logic: all of them – quantum cosmology, quantum physics, quantum metrics and quantum calculus – are the self-informational mathematical systems based on symbolic and numerical functional analysis and elementary recursive calculations of interrelated space and time parameters of matter motion in various states of the material environment.For the first time in scientific and engineering practice, it was clearly shown that the information entropy of both standard symbolic and non-standard numerical functional analysis has absolute exact limits of computational accuracy – 1/10^16 and 1/10^64, respectively. Moreover, the second limit determines the maximum level of accuracy of practical quantum metrics and calculations and fully coordinates four branches of classical physics – thermodynamics, electrodynamics, gravidynamics, chromodynamics with special and general relativity.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

Biochar is a carbon-rich material that recently received attention due to its increasing agronomical potential. The agricultural utilization of biochar relates to its potential to act in the soil as a soil conditioner, nevertheless, the complex information on the direct dependence of biochar physical properties (texture, particle size) and corresponding leaching and availability of organic molecules (e.g. the polycyclic and heterocyclic organic compounds) and inorganic mineral salts (based on micro– and macroelements) are still not consistent. These aspects were addressed in our study. A multi-elemental analysis (ICP-OES) was used to access the information on the aqueous-extractable and total contents of inorganic macro- and macroelements in used commercial biochar samples (purchased from Sonnenerde GmbH, Novoterrra Sonnenerde GmbH, Biouhel.cz, s.r.o.). Potassium (K) was identified as the major macroelement, responsible for alkaline pH and the conductivity of biochar extract. Our results indicate an indirect relation between the size fraction of biochar and the content of extractable K, sodium (Na), and calcium (Ca) and a direct relation with the contents of phosphorus (P) and magnesium (Mg). As the total determined amounts of inorganic elements were significantly higher compared to aqueous-extractable amounts, we believe it could indicate the potential for repeated release to the surrounding soil. These findings were also confirmed by the analysis of biochar samples obtained after the cultivation (duration of 2 years) in selected representative soil samples from the Czech Republic (Cambisol, Fluvisol, Regosol, Chernozem). Moreover, gas chromatography (GC) coupled with mass spectroscopy (MS) was further used to reveal the concentrations of available polycyclic aromatic and heterocyclic compounds in biochar samples. The detected concentration of these types of organic compounds were far below the certified limits. We believe our in-depth analysis could provide the necessary insight into the description of biochar mineral content, its connection to biochar texture, corresponding physicochemical properties and potential availability to leach nutrients to the soil. These findings could help in further assessment of the potential applications of biochar in modern agriculture as a soil conditioner.

The shortage of quantum computers, and their current state of development, constraints research in many fields that could benefit from quantum computing. Although the work of a quantum computer can be simulated with classical computing, personal computers take so long to run quantum experiments that they are not very useful for the progress of research. This manuscript presents an open quantum computing simulation platform that enables quantum computing researchers to have access to high performance simulations. This platform, called QUTE, relies on a supercomputer powerful enough to simulate general purpose quantum circuits of up to 38 qubits, and even more under particular simulations. This manuscript describes in-depth the characteristics of the QUTE platform and the results achieved in certain classical experiments in this field, which would give readers an accurate idea of the system capabilities.

Concretizing the mechanisms of Bergmann rule, we found saw-tooth pattern in body size variation in ground beetle Pterostichus oblongopunctatus. We sampled beetles in 2010 – 2018 at the forest undisturbed plots on the broad territory in Russia. Investigating regions covered territory, extending to 3 degrees latitude and 19 degrees longitude. We measured six traits in every of 3294 caught individual. ANOVA showed that latitude, and sex affected significantly body size of the species studied. Mean values of each trait changed significantly from one studied region to another in females and males as well. Sexual size dimorphism in species was female-biased. We performed models in R to estimate the steepness of body size variation in both sexes. In overwhelming majority of cases that parameter was equal in both sexes. So the hypothesis, that male′s variation is steeper in latitude gradient was not confirmed.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

Scientists, politicians, and practitioners are debating the current structure of pig farms in Lithuania, as medium and small farms have almost disappeared over the past decade. The debated problem is whether the revitalization of medium and small pig farms would sustainably contribute to self-sufficiency in pork? Therefore, this research aims to determine which farms in terms of size could be the most perspective. In order to achieve this aim the multi-criteria evaluation method TOPSIS was used. The economic, production and environmental indicators of Lithuanian pig farms and pig farming sector in Lithuania and selected EU countries: Latvia, Estonia, Poland, Germany, and Denmark were analyzed in this research. The multi-criteria evaluation led to the conclusion that Danish pig farms were the best managed. Germany occupied the second place. The industrial large farms were found as dominated in those countries. Large pig farms (approximately two thousand sows) appeared most perspective in Lithuania: they took the first place in the years examined (2016–2021). The criterion estimate of their assessed indicators was much higher than of the medium (100 sows) and small (20 sows) farms. The main reasons: significantly higher labour productivity, lower cost, lower price, and better production indicators.

(1) Background: Stunting remains a challenge in Indonesia, where 30.8% of under-five children are stunted and may never reach full potential height and cognitive function. We aimed to investigate the risk factors of stunting in Nangapanda subdistrict, East Nusa Tenggara; (2) Methods: The design was cross-sectional study located in rural area as part of PINTERMIDI UI project. We collected quantitative data on social determinants, weight, height, hemoglobin, ferritin, serum zinc, CRP, worm infection, history of deworming, co-morbidity, food security, and nutrient intake; (3) Results: A total of 196 under-five children included and 74% households were food insecure. The prevalence of stunting was 29.9% in this population (31.8% worm infection, 30.3% iron deficiency, and 28.1% zinc deficiency). Multivariate analysis showed household with 5-8 members (AOR 3.076; 95% CI 1.132 – 8.356) and unsafe drinking water (AOR 1.702; 95% CI 0.825 – 3.512) were significant independent risk factors of stunting after adjusted by child’s gender, father’s occupation, caregiver’s education, monthly expenses, sanitary facilities, and food security status; (4) Conclusions: The number of household members is the only independent risk factor of stunting among children age 24-59 months in rural area of Eastern Indonesia. Development of nutrition sensitive intervention and promotion of family planning are needed in order to increase adequate child’s care and feeding practices in rural area of Eastern Indonesia.

Shark unprovoked attacks consist of fatal and non-fatal cases. Numerous cases have been reported involving shark species from Carcharhinus melanopterus with length of 145.5 cm to half-ton Carcharodon carcharias. Currently there are more (P < 0.05) unprovoked non-fatal cases with the average is 28.46 cases/shark species (95%CI: 3.86-53.1) than unprovoked fatal cases, which the average is 5.12 cases /shark species (95%CI: -0.075-10.3). Hence this paper seeks to select the best shark size model that correlates with the unprovoked fatal and non-fatal cases. The studied sharks consist of 24 shark species with the average length is 268.18 cm (95%CI: 230-306 cm) and the average weight is 225.42 kg (95%CI: 128-323 kg). Based on the model and as described by low values of AIC and the highest values of R² and adjusted R² , shark weight followed by combinations of shark weight and length produced unprovoked fatal and non-fatal cases best models. The model for explaining unprovoked fatal cases is the shark weight with high numbers of cases observed in large size shark (weight⁓fatal cases, AIC = 165.359, R² = 0.72, Adj. R = 0.71). While for non-fatal cases, the best model is also the shark weight (weight⁓non fatal cases, AIC = 246.93, R² = 0.63, Adj. R = 0.59).

In December 2012, DOAJ’s parent company, IS4OA, announced they would introduce new criteria for inclusion in DOAJ [1] and that DOAJ would collect vastly more information from journals as part of the accreditation process – and that journals already included, would need to reapply in order to be kept in the registry. My hypothesis was that the journals removed from DOAJ on May 9th 2016 would chiefly be journals from small publishers (mostly single journal publishers) and that DOAJ journal metadata information would reveal that they were journals with a lower level of publishing competence than those that would remain in the DOAJ. Among indicators of publishing competence could be the use of APCs, permanent article identifiers, journal licenses, article level metadata deposited with DOAJ, archiving policy/solutions and/or having a policy in SHERPA/RoMEO. The analysis shows my concerns to be correct.

This Article demonstrates how an eigendecomposition problem is inputted into a quantum circuit, how gates are applied in the quantum circuit, and how the output measurements are the correct eigenvalues. This process is known as quantum phase estimation (QPE). A quantum harmonic oscillator example, a foundational quantum physical chemistry problem, is demonstrated within the context of QPE. A particle in a box example, another quantum physical chemistry problem, may be solved by QPE with a caveat. These examples are of the limiting cases of diagonal matrices. Future advances in taking matrix inverses for solving linear sets of equations or finding ground state energies in the Schrödinger equation will use the principles implemented in this Article.

We develop a renormalizable model of Quantum General Relativity (QGR). We do this by building on earlier work with quantum electrodynamics (QED). Working with the Feynman path integral (FPI) approach to QED, we generalize the paths from varying in space to varying in space and time. This gives the standard results plus dispersion in time of order attoseconds or left. Over longer times, the dispersion in time averages out, but at attosecond times it should be detectable with current technology. As an unexpected but welcome side-effect, the approach caused the usual loop integrals to be finite. Since the usual UV divergences are significantly harder to renormalize in QGR than in QED, and since using paths in time plus space is definitely more in keeping with the general spirit of GR, we here apply the same approach to QGR. We show that with an appropriate choice of gauge (trace-reversed de Donder gauge) we can extend the earlier results to include QGR. Sub-attosecond measurements of individual gravitons are not within our reach, but at least the ultraviolet divergences in QGR are contained in the same way. We have therefore a renormalizable model of QGR

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

We investigate a possible reduction mechanism from (bosonic) Quantum Field Theory (QFT) to Quantum Mechanics (QM), in a way that could explain the apparent loss of degrees of freedom of the original theory in terms of quantum information in the reduced one. This reduction mechanism consists mainly in performing an ansatz on the boson field operator, which takes into account quantum foam and non-commutative geometry. Through the reduction mechanism, QFT reveals its hidden internal structure, which is a quantum network of maximally entangled multipartite states. In the end, a new approach to the quantum simulation of QFT is proposed through the use of QFT's internal quantum network

Starting with a particle in the cube system, we investigate the exotic possibility that the quantum numbers (n_x,n_y,n_z) satisfy the Markov equation. We find that the proposed particle in the Markov-cube system follows from a non-classical information entropic space by the quantum potential Q. We study the classical correspondents of the proposed particle in the Markov-cube system. According to our proposition, this particle identified by detailed measurements of the confinement particle-energy levels is an artifact or occurs in nature.

In this paper, comprehensive analysis of combined effect of major influencing parameters on heat transfer in the single U-tube BHE (sBHE) and double U-tube BHE (dBHE) with two independent circuits was performed by using validated numerical heat transfer model. Geometrical parameters, such as shank spacing (with maximum, average and minimum values) and borehole diameter (large, medium and small borehole sizes) and borehole depth (shallow, average and deep borehole depths) as well as thermal conductivity of soil and grout which ranges from minimum to high value were considered. The combined impact of these parameters was included under four major cases: 1) combined effect of borehole depth, borehole size and shank spacing; 2) combined effect of borehole depth, and soil and grout thermal conductivity; 3) combined effect of soil and grout thermal conductivity and borehole size; and 4) combined effect of soil thermal conductivity, borehole size and shank spacing. Each of these major cases has nine different design options of both sBHE and dBHE. Series of results of heat transfer per unit borehole depth were generated for all the considered various cases. With the given parameters, the BHE case that provides highest heat transfer among the various cases of sBHE and dBHE were obtained.

Engineering of quantum computers requires reliable characterization of qubits, quantum operations, and even the entire hardware. Quantum tomography is an indispensable framework in quantum characterization, verification, and validation (QCVV), which has been widely accepted by researchers. According to the tomographic target, quantum tomography can be categorized into quantum state tomography (QST), quantum process tomography (QPT), gate set tomography (GST), process tensor tomography (PTT), and instrument set tomography (IST). Standard quantum tomography toolkits generally consist of basic linear inverse methods and statistical maximum likelihood estimation (MLE) based methods. Furthermore, the performance of standard methods, including effectiveness and efficiency, has been further developed by exploiting Bayesian estimation, neural networks, matrix completion techniques, etc. In this review, we introduce the fundamental quantum tomography techniques, including QST, QPT, GST, PTT, and IST. We first introduce the details of basic linear inverse methods. Then, the framework of MLE methods with constraints is summarized. Finally, we briefly introduce recent further research in developing the performance of tomography. This review provides a primary getting-start in developing quantum tomography, which promotes quantum computer development.

Models of quantum measurements are presented, including observers subject to the laws of quantum mechanics. Observers perform multiple measurements in an attempt to disprove the collapse hypothesis. It is shown that under reasonable assumptions the effort cannot succeed. Under a unitary evolution the end state is a correlation between the result of the first measurement and the result(s) of the others, consistent with the observer's collapse hypothesis. The observer may conclude that the laws of nature include a non-unitary collapse mechanism, even if one does not actually exist. Discard of information is the crucial factor which distinguishes entanglement from measurement.

Using the projection evolution (PEv) approach, time can be included in the quantum mechanics as an observable. Having the time operator, it is possible to explore the temporal structure of various quantum events. In the present paper we discuss the possibility of constructing a quantum clock, which advances in time during its quantum evolution, in each step having some probability to localize itself on the time axis in the new position. We propose a working two-state model as the simplest example of such a clock.

True randomness is necessary for the security of any cryptographic protocol, including quantum key distribution (QKD). In QKD transceivers, randomness is supplied by one or more local private entropy sources of quantum origin, which can be either passive (e.g. a beam splitter) or active (e.g. an electronic quantum random number generator). In order to understand better the role of randomness in QKD we revisit the well-known "detector blinding" attack on BB84 QKD protocol, which utilizes strong light to achieve an undetectable and complete recovery of the secret key. We present two findings. First, we show that the detector blinding attack is in fact an attack on the receiver’s local entropy source. Second, based on this insight, we propose a modified receiver station and a statistical criterion which together enable robust detection of any bright-light attack and thus restore security.

Quantum amplitude estimation is a numerical integration technique and a candidate for the first operationally used quantum algorithm providing a quantum advantage in the NISQ era. Its main metric is the generated Fisher information per second, as it describes the accuracy of the numerical integration. The development of this metric can be coupled to the quantum volume of the used quantum processor with a phenomenological noise model. Since the increase of the quantum volume seems to follow an exponential pattern, insight in the integration power of quantum amplitude estimation for the upcoming years can be obtained. This shows that quantum amplitude estimation as a numerical integration technique will not provide an advantage for functions without significant improvements to the connectivity, reliability and speed of quantum processors. Beyond that, this method may be used the estimate the development of many more NISQ era algorithms.

In this work the author utilizes the quantum geometrization of spacetime for describing the gravitational interaction within the framework of quantum theory. This approach allows for the development of an equation of gravity that is mathematically connected to the fermion and boson fields. This achievement is accomplished by incorporating two fundamental principles: covariance of the quantum field equations and the principle of least action. By considering these principles, a theory is established that enables the calculation of gravitational corrections to Quantum Electrodynamics, and potentially, to the standard model of particle physics as well. The theory also provides an explanation for two phenomena: the existence of a cosmological pressure density similar to quintessence, that is compatible with the small value of the observed cosmological constant, and the breaking of matter-antimatter symmetry at high energies offering insights into why there is an imbalance between the two in the early universe. In the cosmological modeling of the theory, there exists a proposal to account for the formation of supermassive black holes that are accompanied by their own surrounding galaxies, without relying on the process of mass accretion. The model, in accordance with recent observations conducted by the James Webb Space Telescope, supports the notion that galactic configurations were established relatively early in the history of the universe, shortly after the occurrence of the Big Bang.

The development of quantum computers seeks software developers' attention regarding security in the era of Information Technology, software security is the primary goal for our quantitative assessment of software security in the development cycle of software. Security assessment of software is identifying the key security factors of the software. A security elective provides ex-tensive strategies and calculations to ensure product safety. The security assessment is the key factor in surveying, administering, and controlling security to further enhance the nature of safety. It should be acknowledged that assessing security early on in the development process is beneficial in identifying worms, hazards, flaws, and threats. The definition and portrayal of Quantum Computing (QC) in software security will be discussed in this study. Researchers use cryptography calculations to secure our financial institutions, medical devices, military weaponry, planes, ships, vehicles, and pilots. Here authors of this study use the Fuzzy Technique for Order Preference by Similarity to Ideal Situation (FTOPSIS) to quantitatively assess the weight/rank of the quantum enable security alternatives like (Diffie-Hellman key-exchange algorithm, Quantum key distribution algorithm, Deutsch-Jozsa Algorithm, Special Deutsch-Jozsa Algorithm, Grover’s Algorithm and Quantum key distribution algorithm in GHZ state) with security factors like (Confidentiality, Integrity, Authenti-cation, Privacy, Reliability, Maintainability, Authorization, Integrity, Possessions, and Availability). Additionally, they critically analyze and select the six alternatives of quantum-based security algorithms. The nature of safety infers the ability to execute a thing on time in this exploration study, specifically 'software security'.

Moore’s law will cease to be relevant once transistors are the size of electrons. Once this occurs, we will no longer be able to use silicon for technological advancement. However, breakthroughs will continue in the form of a sixth paradigm: a 3D molecular computing model such as quantum comput- ing. Some of the promising areas of quantum computing researched in this study are (i) algorithmic advancements - such as Shor’s, Grover’s, error correction, fault tolerance and other new algorithms; (ii) hardware - such as the quantum system architecture, circuit models, entanglement, superposition and no-cloning qubits; (iii) market segments - such as finance, healthcare, and chemistry; (iv) the supremacy established over classical computing; and (v) areas of applicability. Significant progress has been made in these areas in recent decades, and they have garnered immense interest, attention and the funding required to make good progress.

Quantum computers are invaluable tools to explore the properties of complex quantum systems. We show that dynamical localization of the quantum sawtooth map, a highly sensitive quantum coherent phenomenon, can be simulated on actual, small-scale quantum processors. Our results demonstrate that quantum computing of dynamical localization may become a convenient tool for evaluating advances in quantum hardware performances.

During the last 25 years the scientific community has coexisted with the most fascinating protocol due to Quantum Physics: quantum teleportation (QTele), which would have been impossible if quantum entanglement, so questioned by Einstein, did not exist. In this work, a complete architecture for the teleportation of Computational Basis States (CBS) is presented. Such CBS will represent each of the possible 24 classical bits commonly used to encode every pixel of a 3-color-channel-image (red-green-blue, or cyan-yellow-magenta). For this purpose, a couple of interfaces: classical-to-quantum (Cl2Qu) and quantum-to-classical (Qu2Cl) are presented with two versions of the teleportation protocol: standard and simplified.

In this paper, the connections between quantum non-locality and permutation symmetries are explored. This includes two types of symmetries: permutation across a superposition and permutation of qubits in a quantum system. An algorithm is proposed for nding the separability class of a quantum state using a method based on factorizing an arbitrary multipartite state into possible partitions, cyclically permuting qubits of the vectors in a superposition to check which separability class it falls into and thereafter using a reduced density-matrix analysis of the system is proposed. For the case of mixed quantum states, conditions for separability are found in terms of the partial transposition of the density matrices of the quantum system. One of these conditions turns out to be the Partial Positive Transpose (PPT) condition. A graphical method for analyzing separability is also proposed. The concept of permutation of qubits is shown to be useful in dening a new entanglement measure in the `engle'.

Inbreeding depression is expected to be more pronounced in fitness-related traits, such as pig litter size. Recent studies have suggested that the genetic determinism of inbreeding depression may be heterogeneous across the genome. Therefore, the objective of this study is to conduct a genomic scan across the pig autosomal genome to detect the genomic regions that control inbreeding depression for litter size in two varieties of Iberian pigs (Entrepelado and Retinto). The datasets consist of 2,069 (338 sows) and 2,028 (327 sows) records for litter size (Total Number Born and Number Born Alive) for the Entrepelado and Retinto varieties. All sows were genotyped using the Geneseek GGP PorcineHD 70 K. We employed the Unfavorable Haplotype Finder software to extract runs of homozygosity (ROHs) and conducted a mixed model analysis to identify highly significant differences between homozygous and heterozygous sows for each specific ROH. A total of 8 genomic regions located on SSC2, SSC5, SSC7, SSC8, and SSC13, were significantly associated with inbreeding depression, housing some relevant genes such as FSHR, LHCGR, CORIN, AQP6, and CEP120.

Polyaniline or PANI is a conductive polymer (CPs) with flexibility in turning into conducting properties. The drawback is mainly in terms of limited mechanical properties improvement which attracted the interest in fabrication of PANI with other polymeric materials. PANI-PVL composites film was synthesized and fabricated in this work with chronological steps according to the objectives aligned in two different phases. The first phase determines the optimum parameters to synthesize nanosized PANI. The ideal initial molar ratio, r was 1, stirring speed of 600 rpm, purified by filtration, synthesis temperature of 25 oC, washed by dopant acid, acetone and distilled water. The usage of non-ionic surfactant, Triton X-100 (TX100) with 0.1 % concentration favours the formation of smaller particle size of PANI and good dispersibility compared to the usage of anionic sodium dodecyl sulphate (SDS). The synthesis of PANI in nanosized dimension has the potential to be applied for antimicrobial applications such as gloves and antimicrobial coating of frequent contact points in the near future.

Abstract: Ovulation failure was associated with a reduction in pre-mating concentrations of oestradiol-17β and prolactin (PRL). The present study aimed to evaluate whether pre-mating PRL levels have a role on the reproductive efficiency of doe rabbits. A total of 78 multiparous California does (2nd parity) were divided, according to plasma pre-mating PRL, into five categories, >20-25, >25-30, >30-35, >35-40, and >40-45 ng/ml. Does in all categories were naturally mated and kindled, then their reproductive measurements and progesterone (P4) levels were determined. Results show that pre-mating PRL averaged 23.60±0.78, 28.00±0.83, 33.46±0.43, 38.17±0.49 and 41.98±0.68 ng/ml in five categories (p < 0.05), respectively, representing the highest distribution (38.5%) in the 3rd-category. Live body weight of doe rabbits, at mating, pregnancy, and parturition increased (p < 0.05) with increasing pre-mating PRL level. The number of services, litter size, and pregnancy rate increased (p < 0.05) by increasing PRL levels. Reproductive traits and P4 level at mid-pregnancy of does, and average weight of kits at birth increased (p < 0.05) by increasing PRL levels. The pre-mating PRL profile is important for the identification of reproductive performance in doe rabbits.

Meganthropus palaeojavanicus was known very tall with body height of 8 feet and this made M. palaeojavanicus as the tallest hominid ever existed. This species was living in closed tropical woodland and hilly landscape as the fossil remains were found in a remote forest in Sangiran, central Java. Owing large body size, it may influence the foraging ecology of M. palaeojavanicus to cope with the terrain. In here, this study aimed to model the M. palaeojavanicus foraging ecology along terrain gradients. The model indicates that within 5 km home range radius, the most suitable foraging areas were in north east since these areas have more flat landscapes with slopes of <7.5%. While less suitable areas in north west and south west areas were characterized by hilly landscapes with rugged terrain and steep slopes with slopes of >62.8%.

The purpose of this paper is to analyze how Green Business Models (BMs) established by small and medium enterprises (SMEs) can incorporate product and process decarbonization in their components (value proposition, creation and capture) and to what extent this incorporation is affected by SME size. We use a database comprising 1,161 observations of SMEs, 466 in 2014 and 695 in 2016. The results show that SMEs’ value propositions give an intermediate valuation to both legally required and voluntary reduction of environmental impact, irrespective of SME size and the year analyzed. Regarding value creation, SMEs adopt practically no environmental practices, and there are significant differences according to size, with more difficulties than advantages stemming from small size. The study also shows that such environmental practices are not effective in reducing carbon. This diagnosis indicates that SMEs need help from the administration if they are to play a key role in the process of transformation toward a low-carbon economy. Legislative actions involving harsher environmental protection measures might help shape value propositions that place greater importance on reducing environmental impact, whereas training actions on available environmental techniques, promotion of research on how to adapt such techniques to SMEs and the development of specific practices for SMEs might enhance environmental value creation and capture in their BMs.

A picture is a powerful and convenient medium for inducing the illusion that one perceives a real three-dimensional scene. The relative invariance of picture perception across viewing positions has aroused the interest of painters, photographers and visual scientists. Many studies have been devoted to perceptual invariance when pictures are viewed from oblique directions. Invariance across viewing distances has received less attention. This study presents a computational analysis of pictures of perspective scenes taken from different distances between camera and physical objects. Distances and directions of pictorial objects were computed as function of viewing distance to the picture and compared with distances and directions of the physical objects as function of camera position. The computations show that pictorial distance and direction are determined by angular size of the depicted objects. Pictorial distance and direction are independent of camera position, focal length of the lens, and picture size. Ratios of pictorial distances, directions and sizes are constant as function of viewing distance. The constant ratios are proposed as the reason for invariance of picture perception over a range of viewing distances. Reanalysis of distance judgments obtained from the literature shows that perspective space, previously proposed as the model for visual space, is also a good model for pictorial space. The geometry of pictorial space contradicts some conceptions about picture perception.

(3+1)D quantum mechanics is a four-dimensional quantum formalism, which is developed neither in a Minkowski spacetime, nor in a purely Hilbert space and not its metric is Lorentzian. This quantum mechanics also yields the quantum Einstein field equation in (3+1)D quantum spacetime. Every observable (3+1)D quantum spacetime can be found to contain internally hidden opposite spin quantum state, that results Supersymmetry. Closed continuous mappings of this hidden quantum state immediately yield more extra hidden dimensions including string. This string is found to be fundamentally eleven-dimensional (rather than lower dimensional) by nature within this quantum spacetime, which is necessarily a natural phenomenon of (3+1)D Quantum Mechanics.

The double nature, wave and corpuscular, of the material particles is usually considered incomprehensible as it cannot be represented visually. It is proposed to the student, in the introductory courses, as a fact justified by quantum interference experiments of which, however, no further analysis is possible. In this note we propose a description of the wave function in terms of a simple electrical analogy, which reproduces at least some of its essential properties. The aim we propose is to provide a cognitive representation of an analogical type: starting from a classical context (electrical circuits) and introducing in an appropriate way the notions of "wave" and "particle", we show how typically quantum properties such as delocalization and entanglement emerge in a natural, understandable and intuitive way.

Quantum mechanics is often described as irreducibly non-local. A tacit element of this picture is the assumption that one and the same sub-ensemble of quanta is post-selected in every measurement combination of a Bell test. Yet, this expectation was recently shown to be formally inconsistent with quantum theory (Cetto et al., 2020) and even to be experimentally falsifiable (Mardari 2021). The need to make sense of this development motivated a rigorous conceptual analysis of quantum non-locality, especially as it relates to the basic principles of quantum mechanics. The simple conclusion is that quantum theory and quantum non-locality are fundamentally incompatible. This is not a loophole around the predictions of quantum mechanics, but rather an insight into the essential conditions that make them accurate.

In recent years, the term quantum-like has been increasingly used in different disciplines, including neurosciences, psychological and socio-economical disciplines, claiming that some investigated phenomena show “something” in common with quantum processes and, therefore, they can be modeled using a sort of quantum formalism. Therefore, the increasing use of the term quantum-like calls for defining and sharing its meaning in order to properly adopt it and avoid possible misuse. In our opinion, the concept of quantum-like may be successfully applied to macroscopic phenomena and empirical sciences other than physics when at least two conditions are satisfied: a) the behavior of the investigated phenomena show logical analogies with quantum ones; b) it is possible to find a criterion of truth based on an experiential/scientific approach applied to a probabilistic model of description of the phenomena. This is only a first, small step in the approach to the concept of quantum-like, hopefully helpful to promote further discussion and achieve a better definition.

Recently, Bennett et al. [Eur. J. Phys. 37:014001, 2016] presented a physically-motivated and explicitly gauge-independent scheme for the quantisation of the electromagnetic field in flat Minkowski space. In this paper we generalise this field quantisation scheme to curved spacetimes. Working within the standard assumptions of quantum field theory and only postulating the physicality of the photon, we derive the Hamiltonian, $\hat H$, and the electric and magnetic field observables, $\hat {\bf E}$ and $\hat {\bf B}$, without having to invoke a specific gauge. As an example, we quantise the electromagnetic field in the spacetime of an accelerated Minkowski observer, Rindler space, and demonstrate consistency with other field quantisation schemes by reproducing the Unruh effect.

In this paper, I propose new models of quantum information processing using the exchange interaction in physical systems. The partial SWAP operator that can be realized using the exchange interaction is used as the underlying resource for defining models of quantum computation, quantum communication, quantum memory and decoherence-free subspaces. Given the non-commutativity of these operators (for adjacent operators operating on a common qubit), a number of quantum states and entanglement patters can be obtained. This zoo of states can be classified, due to the parity constraints and permutation symmetry of the states, into invariant subspaces that are used for the definition of some of the applications in this paper.

Quantum Computation, in the gate array version, uses logical gates adopting convenient forms for computational algorithms based on those of classical computation. There, two-level quantum systems are the basic elements connecting the binary nature of classical computation with the settlement of quantum processing. Despite, their design depends on specific quantum systems and physical interactions involved, exacerbating the dynamics analysis. Predictable and controllable manipulation should be addressed to control the quantum states, but resources are restricted to limitations imposed by the physical settlement. This work presents a formalism to decompose the quantum information dynamics in SU(2^2d) for 2d-partite two-level systems into 2^2d-1 SU(2) quantum subsystems. Decomposition lets to set control procedures, to generate large entangled states and to design specialized dedicated quantum gates. There, easy and traditional operations proposed by quantum computation are recovered for more complex and large systems. Alternating the parameters of local and non-local interactions, the procedure states a universal exchange semantics on the generalized Bell states basis. It could be understood as a momentary splitting of the 2d information channels into 2^2d-1 pairs of 2 level quantum information subsystems and a settlement of the quantum information manipulation free of the imposed restrictions by the underlying physical system.

Silica on Silicon is a major optical integration platform, while the emergent class of integrated Laser written circuits' platform offers additionally high customizability, and flexibility for rapid prototyping. However, the inherent waveguides' low core/cladding refractive index contrast characteristic compared to other photonic platforms in silicon or silicon nitride, sets serious limitations for on-chip efficient coupling with single photon emitters, like semiconductor nanowires with quantum dots limiting the applications in quantum computing. A new light coupling scheme proposed here overcomes this limitation providing means for light coupling >50%. The scheme is based on the incorporation of an optical microsphere between the nanowire and the waveguide, properly optimized and arranged in terms of: size, refractive index, distance of microsphere between nanowire and waveguide. Upon suitable design of the optical arrangement, the photonic nanojet emitted by the illuminated microsphere excites efficiently the guided eigenmodes of the input channel waveguide, thus launching light with high coupling efficiency. The method is tolerant in displacements, misalignments, and imperfections and is fabricationally feasible by current state of the art techniques. The proposed method enables the on-chip multiple single photon emitters' integration thus allowing the development of highly customizable and scalable quantum photonic integrated circuits for quantum computing.

Quantum image representation is a widely researched area of quantum computing. Currently developed methods use angle parameter of the rotation gate (e.g., the FRQI method), sequences of qubits (ex. NEQR method) or phase shift (ex. LPIQE method) for storing color information of pixels. All of those methods are affected by decoherence and other classical and quantum noise, which is an inseparable part of quantum computing in a NISQ (Noisy Intermediate Scale Quantum) era. These all phenomenons influence the measurements, its probability distribution over the measurement basis and, as the result, makes the extracted images not even similar to those, which was stored in quantum computers. Since this process is, in its foundation, quantum as well, the computational reversal of this process is possible. There are a lot of methods for error correction, mitigation and reduction, but all of them use quantum computer time, or additional qubits to achieve desired result. We report a successful use of the Generative Adversarial Network tuned for image-to-image translation in conjunction with PDU method, for error reduction in images encoded using LIPQE (Local Phase Image Quantum Encoding) method.

We propose a theoretical method for the deterministic shaping of quantum light via photon number state selective interactions. Nonclassical states of light are an essential resource for high precision optical techniques that rely on photon correlations and noise reshaping. Notable techniques include quantum enhanced interferometry, ghost imaging, and generating fault tolerant codes for continuous variable optical quantum computing. We show that a class of nonlinear-optical resonators can transform many-photon wavefunctions to produce structured states of light with nonclassical noise statistics. The devices, based on parametric down conversion, utilize the Kerr effect to tune photon number dependent frequency matching, inducing photon number selective interactions. With a high amplitude coherent pump, the number selective interaction shapes the noise of a two-mode squeezed cavity state with minimal dephasing, illustrated with simulations. We specify the requisite material properties to build the device and highlight the remaining material degrees of freedom which offer flexible material design.

We consider new insights into the origin and nature of pointer states and their role in wave function collapse in macroscopic quantum coherence. The work includes new theory of quantum coherence underpinned by turbulence, generated by a field of pointer states in the form of recirculating vortices (toroids), interconnected via a vortex cascade. Decoherence occurs when the interconnected field of vortices between pointer states is disrupted by external forces, leading to their localisation. The applicability of this work is considered in addressing unresolved questions in high temperature superconductivity and macroscopic quantum processes in biological systems. We also consider its implications for our understanding of intrinsic spin and pointer states within the standard "point source" representation of a quantum particle, which intuitively requires a more complexed description.

Having access to a unique quantum circuit that one wants to protect against use by others is a very likely scenario. However currently users rely on classical computer security schemes, which have known shortcomings. In this chapter we introduce a novel protection scheme along with a survey of other known methods to protect quantum information. In particular we review physically unclonable functions (PUFs), obfuscation, and introduce quantum logic locking.

Quantum entanglement is a fascinating topic with both theoretical and technological impacts. Yet, even in the simplest scenarios, there are still various open questions involving pure state and mixed state entanglement. Here we present the simplest entangled mixed states. We consider both qubits (quantum bits) and qudits (quantum digits). We first provide our simplest yet most important result for rank-2 bi-partite states, and we then generalize our results to go beyond rank-2 and to go beyond bi-partite states.

The goal of finding a commutative group of gates from the set of unitary matrices is to simplify the process of quantum computing. If a set of gates is commutative, then we can apply the gates in any order without affecting the final outcome. This is important because quantum systems are very sensitive to errors and decoherence, and any disruption to the system can cause errors in the computation.By having a commutative group of gates, we can simplify the process of designing quantum algorithms and reduce the risk of errors. This is particularly important for solving complex computational problems that cannot be solved by classical computers.

Tremendous progress has been witnessed in artificial intelligence within the domain of neural network backed deep learning systems and its applications. As we approach the post Moore’s Law era, the limit of semiconductor fabrication technology along with a rapid increase in data generation rates have lead to an impending growing challenge of tackling newer and more modern machine learning problems. In parallel, quantum computing has exhibited rapid development in recent years. Due to the potential of a quantum speedup, quantum based learning applications have become an area of significant interest, in hopes that we can leverage quantum systems to solve classical problems. In this work, we propose a quantum deep learning architecture; we demonstrate our quantum neural network architecture on tasks ranging from binary and multi-class classification to generative modelling. Powered by a modified quantum differentiation function along with a hybrid quantum-classic design, our architecture encodes the data with a reduced number of qubits and generates a quantum circuit, loading it onto a quantum platform where the model learns the optimal states iteratively. We conduct intensive experiments on both the local computing environment and IBM-Q quantum platform. The evaluation results demonstrate that our architecture is able to outperform Tensorflow-Quantum by up to 12.51% and 11.71% for a comparable classic deep neural network on the task of classification trained with the same network settings. Furthermore, our GAN architecture runs the discriminator and the generator purely on quantum hardware and utilizes the swap test on qubits to calculate the values of loss functions. In comparing our quantum GAN, we note our architecture is able to achieve similar performance with 98.5% reduction on the parameter set when compared to classical GANs. With the same number of parameters, additionally, QuGAN outperforms other quantum based GANs in the literature for up to 125.0% in terms of similarity between generated distributions and original data sets.

Power spectra always play an important role in the theory of inflation. In particular, the ability to reproduce the galaxy matter power spectrum $ P(k) $ and the CMB temperature angular power spectrum $ C_l $’s to high accuracy is often considered a triumph of inflation. In our previous work, we presented an alternative explanation for the matter power spectrum based on nonperturbative quantum field-theoretical methods applied to Einstein’s gravity, instead of inflation models based on scalar fields. In this work, we review the basic concepts and provide further in-depth investigations. We first update the analysis with more recent data sets and error analysis, and then extend our predictions to the CMB angular spectrum coefficients $ C_l $, which we did not consider previously. Then we investigate further the potential freedoms and uncertainties associated with the fundamental parameters that are part of this picture, and show how recent cosmological data provides significant constraints on these quantities. Overall, we find good general consistency between theory and data, even potentially favoring the gravitationally-motivated picture at the largest scales. We summarize our results by outlining how this picture can be tested in the near future with increasingly accurate astrophysical measurements.

Sample size using prevalence has been one of the most important medical research methodologies and has been used in original articles more often than any other statistical tool available. The simple formula consists of variables interdependent and it is as important to understand how they influence each other as it is to learn to use the formula to calculate the sample size. With the choice of different amounts of precision and levels of confidence available to a medical researcher, it should be of paramount importance to understand what a slight change in choosing the parameter would mean at the end of the research. Understanding of different Z values, Levels of precision, and ranging Prevalence is required to understand the effect on the sample size and subsequently on the research. Topological representation using parameter ranges can be used to demonstrate this relationship.

This study aimed to investigate the interactions between corn particle size (PS) and conditioning temperature (CT) on the performance, carcass traits, intestinal morphology, and immune responses in broilers fed a corn-soybean meal-based diet. A total of 360, one-day-old male broiler chicks (Ross 308) were randomly allocated into six dietary treatments in a 2×3 factorial arrangement, consisting of two corn PS (finely ground with geometric mean diameter (GMD) of 357 µm (PSF) vs. coarsely ground corn with GMD of 737 µm (PSC), and three CT [unconditioned (CTU), conditioned at 75◦C (CT75) and 90◦C (CT90)]. Birds accommodated in 30 pens with five replicates and 12 chicks per each. There was no interaction between corn PS and CT on growth performance and immune response of broilers at any growth phases. However, during the starter (0-10d) period, the average daily weight gain (ADWG) and feed conversion ratio (FCR) of PSF-fed birds were significantly improved compared to those fed PSC (P<0.05). During the starter (0-10d) and grower (11-24d) periods, increasing the conditioning temperature of corn increased the ADWG, while in the starter phase only the CT75 caused a lower FCR (P<0.05). Broilers fed PSF corn showed lowest FCR during the finisher (25-42d) period compared to those fed PSC (P<0.05). Conditioning corn at 75ºC reduced FCR during the finisher (25-42d) period compared to the birds fed CTU and CT90 corn (P<0.05). In whole experimental periods (1-42d), PSF and CT75 treatment increased the ADWG compared to the PSC and CTU (P<0.05). The CT75 treatment improved primary total anti-sheep red blood cell (SRBCs) titer (IgT) and IgM and secondary IgT and IgG responses compared to the other experimental groups (CTU and CT90) (P<0.05). No significant PS × CT interaction was found on Newcastle disease (ND) antibody titer of broiler chickens (P>0.05). Feeding CT75 corn reduced duodenum and jejunum relative length compared to the birds fed diets containing CTU corn. Significant PS×CT interactions (P<0.05) were observed for villus height, villus height to crypt depth, crypt depth, muscle thickness, and absorption surface area of jejunum. The highest carcass yield observed in PSF-CT75-group (P<0.05). In conclusion, the use of finely ground corn (PSF) conditioned at 75℃ (CT75) was beneficial to growth performance, development of the digestive tract, jejunum histomorphometry and the immune responses of broilers.

Remanufacturing is a way for product recovery initiative and maintaining sufficient production flow to satisfy customer demand through circular economy. Recently, manufacturers have been progressively incorporating remanufacturing processes, making their supply chain vulnerable to disruptions. Among the disruptions that usually occur is the shortage in spare parts supply, which causes unexpected delay in production and possible loss of sales. In the face of potential disruption, it is essential for remanufacturing facilities to manage their supply chains in an optimum manner as to decrease the adverse impact of disruptions to their business. In this study, a two-stage production-inventory system is analysed by developing a cost-minimisation model focusing on the recovery schedule after a disruption occurrence in sourcing spare parts for a remanufacturer’s production cycle. The developed model was solved using the branch and bound algorithm. Through numerical experiments, the results indicate that the optimal recovery schedule and the number of recovery cycles are significantly dependant on disruption time, lost sales and backorder costs. Moreover, a sensitivity analysis shows that the lost sales option seems to be more effective than the backorder option in optimising the system’s overall cost. The proposed model could assist managers in deciding the optimal production strategy while providing interesting managerial insights into vital spare parts recovery issues when disruption strikes.