Hydraulic fracturing in shale gas reservoirs has usually resulted in complex fracture network. The results of micro-seismic monitoring showed that the nature and degree of fracture complexity must be clearly understood to optimize stimulation design and completion strategy. This is often called stimulated reservoir volume (SRV). In the oil & gas industry, stimulated reservoir volume has made the shale gas exploitation and development so successful, so it is a main technique in shale gas development. The successful exploitation and development of shale gas reservoir has mainly relied on some combined technologies such as horizontal drilling, multi-stage completions, innovative fracturing, and fracture mapping to engineer economic completions. Hydraulic fracturing with large volumes of proppant and fracturing fluids will not only create high conductivity primary fractures but also stimulate adjacent natural fractures. Fracture network forming around every hydraulic fracture yields a stimulated reservoir volume. A model of horizontal wells which was based on a shale gas reservoir after volume fracturing in China was established to analyze the effect of related parameters on the production of multi-fractured horizontal wells in this paper. The adsorbed gas in the shale gas reservoir is simulated by dissolved gas in the immobile oil. The key to simulate SRV is to accurately represent the hydraulic fractures and the induced complex natural fracture system. However, current numerical simulation methods, such as dual porosity modeling, discrete modeling, have the following limitations: 1) time-consuming to set up hydraulic and natural fracture system; 2) large computation time required. In this paper, the shape of the stimulated formation is described by an expanding ellipsoid. Simplified stimulated zones with higher permeability were used to model the hydraulic fracture and the induced complex natural fracture system. In other words, each primary fracture has an enhanced zone, namely SRV zone. This method saves much developing fine-grid time and computing time. Compared with the simulation results of fine-grid reference model, it has shown that this simplified model greatly decreases simulation time and provides accurate results. In order to analyze the impacts of related parameters on production, a series of simulation scenarios and corresponding production performance were designed. Optimal design and analyses of fracturing parameters and the formation parameters have been calculated in this model. Simulation results showed that the number of primary fractures, half length, SRV half-width and drop-down have great effects on the post-fracturing production. Formation anisotropies also control the production performance while the conductivity of the primary fractures and SRV permeability do not have much impact on production performance. The complexity of stimulated reservoir volume has strong effect on gas well productivity. Fracture number mainly affects the early time production performance. The increase of SRV width cannot enlarge the drainage area of the multi-fractured horizontal wells, but it can improve the recovery in its own drainage region. Permeability anisotropies have much effect on production rate, especially the late time production rate. The results prove that horizontal well with volume fracturing plays an irreplaceable role in the development of ultra-low permeability shale gas reservoir.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

For many decades, X-ray diffraction (XRD) has been used for material characterization. With the recent development in material science understanding and technology, various new materials are being developed, which requires upgrading the existing analytical techniques such that intricate problems can be solved. Although, XRD is a well-established non-destructive technique, it still requires further improvements in its characterization capabilities, especially when dealing with complex mineral structures. The present review conducts comprehensive discussions on atomic crystal structure, XRD principle, its applications, uncertainty during XRD analysis, and required safety precautions, all in one place. It further discusses the future research directions, especially the use of artificial intelligence and machine learning tools for improving the effectiveness and accuracy of XRD technique for mineral characterization. It has been focused that how XRD patterns can be utilized for a thorough understanding of the crystalline structure, size, and orientation, dislocation density, phase identification, quantification, and transformation, information about lattice parameters, residual stress, and strain, and thermal expansion coefficient of materials. All these important discussions on XRD for mineral characterization are compiled in this short yet comprehensive review that would benefit specialists and engineers in the chemical, mining, iron, metallurgy, and steel industries.

In this paper the influence of austempering temperature and salt bath agitation on the final microstructure and mechanical properties of the ferritic ductile iron were studied. 17 samples had been subjected to different heat treatment parameters. Different microstructures were recorded upon the completion of the tests. From the obtained micro images, it is obvious that both the austempering temperature and salt bath agitation affect the final microstructure of the austempered ductile iron. Lower austempering temperatures and salt bath agitation produce more ausferrite in the microstructure, hence the harder and tougher phases are present. This was confirmed with hardness and toughness test of the 17 heat-treated samples. Lower austempering temperatures give more ausferrite phase and therefore higher hardness, but hardness decreases with increasing austempering temperatures. Toughness rises with rising austempering temperatures, but drops significantly with temperatures above 395°C because of the final microstructure.

Diseases caused by contaminated water consumption and poor hygiene are among the leading cause of death in children, the elderly and people with compromised immune system. The present study aims to assess the drinking water quality of some selected drinking water sources in the chosen study area using water quality index (WQI). Samples of drinking waters were collected from four different sources—river, sachet (packaged), borehole and well in Jabi, Abuja, Nigeria for physicochemical and bacteriological analyses using standard methods. With the exception of pH, river water had the highest content of all the physicochemical parameters examined. Some of the physicochemical parameters such as temperature and pH determined in this study were mostly within the World Health Organization (WHO) standard. The bacteriological analyses revealed that the highest total viable counts of 1.54 (0.12) × 10² (cfu/mL) were obtained in the river sample while the least values of 0.03 (0.00) × 10² (cfu/mL) were obtained in the sachet water. Three bacterial isolates of Escherichia coli, Pseudomonas spp and Aeromonas spp were isolated from well water while Pseudomonas spp and Proteus spp were isolated from borehole water. All other bacteria were isolated from the river. The study demonstrates that the safest drinking water source in Idu district, Jabi, Abuja is the sachet/packaged water while the least safe is the river water due to the presence of significant opportunistic pathogens. The results of this study are beneficial for water quality management and could be used for low-cost effective water quality assessment in Jabi.

Aquaculture is one of the fastest-growing animal food-producing agricultural industries in the world and proper performance of fish in morphological, physiological and immunological aspects is important for fish production and sustainable expansion of aquaculture. But several inhibitors like disease, pathogen, and adverse environment can overpower these performances. At present, antibiotics in preventing these inhibitors have been seen as becoming favorable to those inhibitors. So, Bacillus, an important group of probiotic bacteria can be an alternative to these antibiotics in aquaculture. Bacillus has been seen used in different experiments, mainly as a supplement in feed at various concentrations. Bacillus showed effective results like improved growth with minimum cost, improvement in reproduction, hematology, improved immune response and disease, and stress resistance as well as better proximate composition in different fish species. Application of Bacillus strains has proven efficient in improving water quality by reducing ammonia and nitrite toxicity, harmful algal blooms and utilization of H⁺ ion. Larger application of probiotic Bacillus instead of the hazardous synthetic chemicals would promote eco-friendly low-input sustainable aquaculture for food and nutritional security of the increasing world population. So many more experiments should be conducted in commercially important fishes for better growth and health of fishes which will certainly increase fish

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

This paper presents preliminary operational performance results of a pilot grid-connected photovoltaic (PV) system designed and installed on the rooftop of the Ministry of Petroleum, Energy and Mining headquarter in Nouakchott (latitude of 18.1°N and the longitude of 16.0°W), Mauritania. The aim is for the government to demonstrate the relevance of using solar energy and to encourage the uptake of solar PV technology for commercial and residential building applications in Mauritania.. In this study, the grid-connected PV system has a peak power of 48 kW and the performance monitoring was carried out during one year, with a system that allow to measure DC power, inverter and system conversion efficiency, energy generated by the PV arrays, solar radiation in the inclination plane of panels, ambient temperature and module temperature. During this period, the PV plant was found to supply 65,668 kWh to the grid. The final yield ranged from 3.91 to 5.09 kWh/kWp/day. The performance ratio was found to vary from 69.69% to 89.35% and the annual capacity factor was found to be 19%. Finally, performance parameters were compared with other PV plants installed in the same region of Northern Africa. The outcome of this work is deemed important in assisting accurate PV system design and decision-making.

We studied the effect of the structure parameters of engine annular cooling fan with outer ring on the aerodynamic performance by means of experiments and model simulation in fluent^®. Firstly, based on the experiment, a computational model is developed to calculate and analyze the aerodynamic performance of the tested annular fan. The model is validated by comparing the test results with the calculated data. Besides, the aerodynamic performance differences between two types of fans (common fan without outer ring and annular fan with outer ring) are discussed. Based on the computational model, the relation between aerodynamic performance and the outer ring structure parameters are investigated. The results show that the relative parameter on the axial direction has great influence on the aerodynamic performance; while the effect of radial relative parameter is minor. In addition, the outer ring with arc chamfer structure in the downstream side can improve its static pressure efficiency effectively.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

Estimating the vehicle crashworthiness parameters experimentally is expensive and time consuming. For these reasons different modelling approaches are utilized to predict the vehicle behaviour and reduce the need for full-scale crash testing. The earlier numerical methods used for vehicle crashworthiness analysis were based on the use of lumped parameters models (LPM), a combination of masses and nonlinear springs interconnected in various configurations. Nowadays, the explicit nonlinear finite element analysis (FEA) is probably the most widely recognized modelling technique. Although informative, finite element models (FEM) of vehicle crash are expensive both in terms of man-hours put into assembling the model and related computational costs. A simpler analytical tool for early analysis of vehicle crashworthiness could greatly assist the modelling and save time. In this paper a simple piecewise LPM composed of a mass-spring-damper system, is used to estimate the vehicle crashworthiness parameters, focusing on the dynamic crush and the acceleration severity index (ASI). The model is first calibrated against a full-scale crash test and a FEM, post-processed with the LS-DYNA software, at an impact velocity of 56 km/h. The genetic algorithm is used to calibrate the model by estimating the piecewise lumped parameters (stiffness and damping of the front structure of the vehicle). After calibration, the LPM is applied to a range of velocities (40, 48, 64 and 72 km/h). The predictions for crashworthiness parameters from the LPM were compared with the predictions from the FEA and the results are much similar. It is shown that the LPM can assist in crash analysis, since LPM has some predictive capabilities and requires less computation time in comparison with the explicit nonlinear FEA.

Studies on the gait's parameters have been identified on the patients population. Most researchers confirm that the patients walk differently than normal people and they may have a risk for falls. Consistent finding and description of gender, age, and body mass index differences in gait studies is rare in healthy subjects. A cross-sectional study with forty-five young adult (F = 20, M = 25) was conducted. Stadiometer and Physilog 4 inertial sensors were used for data collection. A gait analyser 5.2 software (GaitUp, S.A. Lausanne, Switzerland) was used to determine spatiotemporal parameters. No statistically significant differences were found in any bilateral foot gait parameters with respect to gender, age, and body mass index. Females are found with higher total double support and cadence than males. Cadence also increases with age. Obese people showed lower gait speed, cadence, and total double support. These findings may be beneficial to those who have abnormal gait pattern due to age, body mass index differences, decreased muscle strength, spasticity, and joint mobility. This important informations should be considered to rehabilitate patients with abnormal gait patterns to controlling dynamic balance and riks to falling.

In wideband radar systems, the performance of motion parameters estimation can significantly affect the performance of object detection and the quality of inverse synthetic aperture radar (ISAR) imaging. Although the traditional motion parameters estimation methods can reduce the range migration (RM) and Doppler frequency migration (DFM) effects in ISAR imaging, the computational complexity is high. In this paper, we propose a new fast non-searching motion parameters estimation method based on cross-correlation of adjacent echoes (CCAE) for wideband LFM signals. A cross-correlation operation is carried out for two adjacent echo signals, then the motion parameters can be calculated by estimating the frequency of the correlation result. The proposed CCAE method can be applied directly to the stretching system, which is commonly adopted in wideband radar systems. Simulational results demonstrate that the new method can achieve better estimation performances, with much lower computational cost, compared with existing methods. The experimental results on real radar data sets are also evaluated to verify the effectiveness and superiority of the proposed method compared to the state-of-the-art existing methods.

In recent years, remote sensing technology has been widely used to predict forest stand parameters. In order to compare the effects of different features of remote sensing images and topographic information on the prediction of forest stand parameters, multivariate stepwise regression analysis method was used to build estimation models for important forest stand parameters by using textural and spectral features as well as topographic information of SPOT-5 satellite images in northeastern Heilongjiang Province in China as independent variables. The study results show that the optimal window to predict forest stand parameters using textural features of SPOT-5 satellite image is 9×9; the ability of textural features was better than that of spectral features in terms of predicting forest stand parameters; with the inclusion of topographic information, the accuracy of prediction of all models was improved, of which elevation has the most significant effect. The highest accuracy was achieved when predicting the stand volume (SV) (R²_adj=0.820), followed by basal area (BA) (R²_adj =0.778), accuracy of both above models exceeded 75%. The results show that models combined use of textural, spectral features and topographic information of SPOT-5 images have a good application prospect in predicting forest stand parameters.

This paper deals with the environmental characterization of a large and densely populated area, with a poor reputation for contamination, considering the contribution of environmental features (air, soil, soil hydraulic and groundwater) and the potential effects on human health. The use of Geographic Information System (GIS) has made possible a georeferenced inventory and, by overlaying environmental information, an operational synthesis of comprehensive environmental conditions. The cumulative effects on environmental features were evaluated, taking into account superposition effects, by means of the spatial multicriteria decision analysis (S-MCDA). The application of the S-MCDA for converging the combination of heterogeneous factors, related to soil, land and water, deeply studied by heterogeneous groups of experts, constitutes the novelty of the paper. The results confirmed an overall higher potential of exposure to contaminants in the environment and higher mortality rates in the study area for some tumours, but hospital admissions for tumours were generally similar to the regional trend. Besides, mortality data may be strictly dependent on the poor socioeconomic conditions, quality of therapy and a lack of welfare in the area relative to the rest of Italy. Finally, as regards the possible relationship between presence of contaminants in the environment and health conditions of the population no definite conclusions can be drawn, although the present study encourages the use of the new proposed methods, that increase the possibilities for studying the combined effect of more environmental factors.

Groundwater is an important role of the environment in natural resources. The major sources of groundwater contamination in this study were open discharges of domestic sewage, inadequate sewerage system, open defecation, septic tanks, soak pits, contaminated water pools, unorganized solid waste dumping and use of fertilizers, pesticides for agriculture deteriorated the condition. In this present study revealed that the physical and chemical characteristics of ground water in different areas of Kannur district in Kerala have been determined different seasons with respect to its suitability for drinking and agricultural purposes. For this study the groundwater samples were collected during pre-monsoon and post-monsoon seasons from 70 wells representing the entire the study area. The groundwater samples were analyzed for Physico-chemical characteristics using standard techniques in laboratory and compared with standards. The samples were analyzed with reference to the WHO and BIS standards. The groundwater quality information of the entire study area have been prepared using statistical and GIS technique for all the parameters. This paper proved in GIS will be helpful for measuring, monitoring and managing the groundwater pollution in the study area and suggested to protect groundwater resources in the environment.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

Keenjhar Lake is the main source of drinking water for the metropolitan city of Karachi. The release of untreated wastewater from Kotri industrial area and other sources have made the lake water polluted. This study was subjected to determine the impacts of such pollutant sources on the water quality of Keenjhar Lake. The study involves the analysis of water quality parameters of Keenjhar Lake and its Feeding source (KB Feeder). The sampling sites were selected based on the sources of contamination. The water samples are tested for physical, chemical and microbiological parameters. The result of water analysis indicates the contamination level of the lake is quite alarming for the sites of Kotri effluent and WAPDA colony where Total Dissolved Solids (TDS), Chloride and other ionic metals were quite higher in concentration than other sites. These sites are also contaminated with Fluoride and Arsenic which are carcinogenic elements. The study reveals that the contamination level of feeding source is causing big non-reversible damage to the lake if continued to be uncontrolled. This contamination is mainly due to the release of toxic metals and ions in the KB feeder caused by human carelessness.

This paper proposes a novel model for a PV cell with parameters variance dependency on temperature and irradiance included. The model relies on commercial available data, calculates the cell parameters for standard conditions and then extrapolates them for the whole operating range. An up-to-date review of the PV modeling is also included with series and parallel parasitic resistance values and dependencies discussed. The parameters variance is analyzed and included in the proposed PV model, where the self-heating phenomenon is also considered. Each parameter variance is compared to the results from different authors. The model includes only standard components and can be run on any SPICE-based simulator. Unlike other approaches that consider the internal temperature as a parameter, our proposal relies on air temperature as an input and computes the actual internal temperature accordingly. Finally, the model is validated via experiments and comparisons to similar approaches are provided.

I deal with perception and action (e.g. movements) using results from Synergetics, a comprehensive mathematical theory of the selforganized formation ("emergence“) of spatial, temporal, or functional structures in complex systems. I illustrate basic concepts such as order parameters (ops), enslavement, complexity reduction, circular causality first by examples of well known collective, spontaneous modes of human behavior such as rhythmic clapping of hands etc., and then by face recognition. The role played by ops depends on context. In the case of face (or pattern) recognition an op represents the concept of an individual face (action of mind) and it enslaves the action (firing rates) of neurons (body). This insight allows me to interpret syndroms as order parameters playing their mind/body double role. I present criteria for the identification of ops and discuss their general properties including error correction and "remedy“ of deficiencies. Contact is made with a recent paper by Sabine Koch on embodied aesthetics. My approach includes the saturation of attention at various time scales (ambiguous figures/fashion). Adopting a psychological perspective, I discuss some ingredients of beauty such as proportionality and symmetry, but also the importance of irregularities.

In this work α-synuclein amyloid fibrils, formation of which is a biomarker of the Parkinson’s disease, were investigated with the use of fluorescent probe thioflavin T (ThT). Experimental conditions of the protein fibrillogenesis were chosen so that a sufficient number of continuous measurements can be performed to characterize and analyze all stages of this process. The reproducibility of fibrillogenesis and the structure of the obtained aggregates (that is a critical point for their further investigation) were proved using a wide range of physical-chemical methods. For determination of ThT—α-synuclein amyloid fibrils binding parameters sample and reference solutions were prepared with the use of equilibrium microdialysis. By absorption spectroscopy of these solutions ThT—fibrils binding mode with the binding constant about 10⁴ M⁻¹ and stoichiometry of ThT per protein molecule about 1:8 was observed. Fluorescence spectroscopy of the same solutions with the subsequent correction of the recorded fluorescence intensity on the primary inner filter effect allowed to determine another mode of ThT binding to fibrils with the binding constant about 10⁶ M⁻¹ and stoichiometry about 1:2500. Analysis of photophysical characteristics of the dye molecules bound to the sites of different binding modes allowed to assume the possible localization of these sites. Obtained differences in the ThT binding parameters to amyloid fibrils formed from α-synuclein and other amyloidogenic proteins, as well as in the photophysical characteristics of the bound dye, confirmed the hypothesis of amyloid fibrils polymorphism.

Background: Dietary supplements (DS) represent a possible approach to improve sperm parameters and male fertility. A wide range of DS containing different nutrients is now available. Although many authors demonstrated benefits from some nutrients in male infertility, their real effectiveness is still under debate. The aim of this study was to critically review the composition of DS using the Italian market as sample. Materials & Methods: Active ingredients and their minimal effective daily dose (mFED) were identified through literature search. Thereafter, we created a formula to classify the expected efficacy of each DS. Considering active ingredients, their concentration and the recommended daily dose, DS were scored into three classes of expected efficacy: higher, lower and none. Results: Twenty-one DS were identified. Most of them had a large number of ingredients, frequently at doses below mFED or with unproven efficacy. Zinc was the most common ingredient of DS (70% of products), followed by selenium, arginine, coenzyme Q and folic acid. By applying our scoring system, 9.5% of DS fell in higher class, 71.4% in lower class and 19.1% in the class with no expected efficacy. Conclusions: DS marketed in Italy for male infertility frequently include effective ingredients but also a large number of substances at insufficient dose or with no proven efficacy. Manufacturers and physicians should better consider the scientific evidence on effective ingredients and their doses before formulating and prescribing these products.

The article reviews the constituent’s physico-chemical parameters in the water of the Mansagar Lake of the Jaipur City. The water quality is also investigated using evaluated physico-chemical parameters with in-depth study of their distribution as per sample location-wise and season-wise. A detailed discussion on the associationship among parameters (pH, Conductivity, turbidity, dissolved Oxygen, chemical and Biochemical Oxygen demand, etc.) using the Pearson’s analytical method is also presented. The strength of the article is the graphical presentation of evaluated physico-chemical parameters and the water quality indices for sample station-wise and the season-wise. To our best of understanding, first time such details have been clubbed together and discussion in brief for studied lake.

We mainly describe the influence factors of captured power by huge wave energy harvesters, which the vertical motion of buoy can transform ocean’s potential energy into piezoelectric energy power by waves. By means of semi-analytical solutions and theoretical analysis, related environmental coefficients are analyzed firstly and find the most appropriate wave frequency and geometric structure as reference. Secondly, the numerical results also discuss the impact trend of hydrodynamic parameters and geometric volume on motion, voltage and power with qualitative agreement. The simulation data confirm that structure parameters of the modified model could markedly deliver sufficient power to ocean high electrical equipment with long-time stability.

In this paper, the Fourier-based synchrosqueezing transform (FSST) method is introduced into the power system to realize low frequency oscillation identification. Firstly, the modal components of low frequency oscillation signal are separated by FSST, and calculating the instantaneous parameters including magnitude, frequency and phase of every mode component with Hilbert transform. Then , calculating the damping ration of every modal component based on above parameters and derived the formulas. Thus, it realized effective identification of of modal parameters of low frequency oscillation signal. The experimental results of simulated data and 16-generator system demonstrate the validity and correctness of the FSST method. Comparing with the classical Prony method shows that the FSST method is better in the identification accuracy when the low frequency oscillation signal is polluted by noise. Finally, the effectiveness of the FSST in Actual power grid is verified based on the real data from Sichuan power grid.

The paper proposes TOPSIS method for solving multi-objective multi-level programming problem (MO-MLPP) with fuzzy parameters via fuzzy goal programming (FGP). At first, - cut method is used to transform the fuzzily described MO-MLPP into deterministic MO-MLPP. Then, for specific , we construct the membership functions of distance functions from positive ideal solution (PIS) and negative ideal solution (NIS) of all level decision makers (DMs). Thereafter, FGP based multi-objective decision model is established for each level DM for obtaining individual optimal solution. A possible relaxation on decisions for all DMs is taken into account for satisfactory solution. Subsequently, two FGP models are developed and compromise optimal solutions are found by minimizing the sum of negative deviational variables. To recognize the better compromise optimal solution, the concept of distance functions is utilized. Finally, a novel algorithm for MO-MLPP involving fuzzy parameters is provided and an illustrative example is solved to verify the proposed procedure.

This paper presents the super-twisting algorithm (STA) direct power control (DPC) scheme for the control of active and reactive powers of grid-connected DFIG. Simulations of 5 KW DFIG has been presented to validate the effectiveness and robustness of the proposed approach in the presence of uncertainties with respect to vector control (VC). The proposed controller schemes with fixed gains are effective in reducing the ripple of active and reactive powers, effectively suppress sliding-mode chattering and the effe This paper presents a comparative study of two approaches for the direct power control (DPC) of doubly-fed induction generator (DFIG) based on wind energy conversion system (WECS). Vector Control (VC) and Sliding Mode Control (SMC). The simulation results of the DFIG of 5 KW in the presence of various uncertainties were carried out to evaluate the capability and robustness of the proposed control scheme. The (SMC) strategy is the most appropriate scheme with the best combination such as reducing high powers ripple, diminishing steady-state error in addition to the fact that the impact of machine parameter variations does not change the system performance. cts of parametric uncertainties not affecting system performance.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

In accordance with problems such as difficulty in obtaining aerodynamic parameters of a quad-rotor model, the change of model parameters with external interference affects the control performances, an aerodynamic parameter estimation method and an adaptive attitude control method based on LADRC are designed. Firstly, the motion model, dynamics model and control distribution model of quad-rotor are established by using the aerodynamic and Newtonian Euler equations. Secondly, the identification tool CIFER is used to identify the aerodynamic parameters with large uncertainties in frequency domain and a more accurate attitude model of the quad-rotor is obtained. Then an adaptive attitude decoupling controller based on LADRC is designed to solve the problem of poor anti-interference ability of the quad-rotor, so that the control parameter b0 can be automatically adjusted to identify the change of the moment of inertia in real time. Finally, a semi-physical simulation platform is used for simulation verification. The results show that the adaptive LADRC attitude controller designed can effectively estimate and compensate the system's internal and external disturbances, and the tracking speed of the controller is faster and the precision is higher which can effectively improve system's anti-interference and robustness.

Different process parameters can alter the temperature during machining. Consequently, selecting process parameters that lead to a desirable cutting temperature would help to increase the tool life, decrease the tensile residual stress, and controls the microstructure evolution of the workpiece. An inverse computational methodology is proposed to design the process parameters for specific cutting temperature. A physics-based analytical model is used to predict the temperature induced by cutting forces. To calculate the temperature induced by the deformation in the shear zone, a moving point heat source approach is used. The shear deformation and chip formation model is implemented to calculate machining forces as functions of process parameters, material properties, and etc. The proposed model uses the analytical model to predict the cutting temperatures and applies a variance-based recursive method to guide the inverse analysis. In order to achieve the cutting process parameters, an iterative gradient search is used to adaptively approach the specific temperature by the optimization of process parameters such that an inverse reasoning can be achieved. Experimental data are used to illustrate the implementation and validate the viability of the computational methodology.

Background: Cardiomyopathy is commonly observed disease that may occurs due to mutations in either susceptible genes or modifier gene. People with broad age group are affected either attributable to spontaneous or inherited mutations of these genes. Various gene mutations are reported so far but only few of them were studied in detail. Methods: In the current study, we evaluated epidemiological variables like age, sex, familial status, parental consanguinity. We also described specific clinical symptoms associated with the cardiomyopathy condition in Indian population. Results: Our studies on mutation screening of phospholamban gene revealed two transitions (4880 C/T, 4887 T/G) in 5’ flanking region which might cause inherited dilated cardiomyopathy with refractory congestive heart failure are We further deliberated the gene polymorphism of renin angiotensin system gene angiotensin-1-converting enzyme as an associated marker/ modifier in cardiomyopathy patients and their family members. Conclusions: Information on epidemiological, clinical statistics, phospholamban gene mutation analysis and angiotensin-1-converting enzyme gene polymorphism is essential to guide the successful execution for future therapies and benefits us to identify those patients at risk for faster disease progression, congestive heart failure, and arrhythmia.

The acetylcholinesterase (AChE) inhibitors are the main drugs for symptomatic treatment of neurodegenerative disorders like Alzheimer’s disease. A recently designed, synthesized and tested hybrid compound between the AChE inhibitor galantamine (GAL) and the antioxidant polyphenol curcumin (CU) showed high AChE inhibition in vitro. Here, we describe tests for acute and short-term toxicity in mice as well as antioxidant tests on brain homogenates measured the levels of malondialdehide (MDA) and glutathione (GSH). Haematological and serum biochemical analyses were also performed. In the acute toxicity tests, the novel AChE inhibitor given orally in mice showed LD50 of 49 mg/kg. The short-term administration of 2.5 and 5 mg/kg did not show toxicity. In the ex vivo tests, the GAL-CU hybrid performed better than GAL and CU themselves. In a dose of 5 mg/kg, it demonstrates 25% reduction in AChE activity, 28% and 73% increase in the levels of MDA and GSH, respectively. No significant changes in blood biochemical data were observed. The GAL-CU hybrid is a novel non-toxic AChE inhibitor with high antioxidant activity which makes it a perspective multitarget drug candidate for treatment of Alzheimer’s disease.

All transmission disease depends on the transmission opportunity or medium like humans in COVID-19. Due to globalization and regular movement of people from one country to another, spread of COVID 19 reached to 208 countries till May 10, 2020. For any society health is major concern for humanity as well as administration. Any pandemic is declared as and when it reached at a particular severity level and control vice versa. So, we have continued the daily COVID 19 cases analysis and segregated till May 10, 2020. We have included at least 25 countries for the analysis purpose due to limitation of number of observations in the analysis. Maximum number of day’s data available for China is for 100 days, followed by Iran for 81 days, minimum number of days data is for 16 days for Western Sahara and Tajikistan.

The water quality of the river is becoming deteriorated due to human interference. It is essential to understand the relationship between human activities and land-use types to assess the water quality of a region. GIS has the latest tool for analyzing the spatial correlation. Land use land cover and change detection is the best illustration to show the human interactions on land features. The study assessed water quality index of upper Ganga River near Haridwar, Uttarakhand and spatially correlated them with changing land use to reach a logical conclusion. At the upper course of Ganga along 78 Km long from Kaudiyala to Bhogpur, water samples were collected from five stations. For water quality index the physicochemical parameters like pH, EC, DO, TDS, CaCO3-, CaCO3, Cl¯, Ca++, Mg++, Na+, K+, F-, Fe2+ were considered. The result of the spatial analysis was evaluated through error estimation and spatial correlation. The root mean square error between spatial land use and water quality index of selected sampling sites was estimated as 0.1443. The spatial correlation between land-use change and site-wise differences in water quality index has also shown a high positive correlation with R² = 0.8455. The degree of positive correlation and root mean square error has strongly indicated that the water quality of the river at the upper course of Ganga is highly impacted through human activities.

Developing particles of different anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Gold atoms of certain transition state develop monolayer assembly at solution surface around the light glow (known in argon plasma) being generated at bottom of copper capillary (known in cathode). The rate of uplifting gold atoms to solution surface is being controlled by forcing energy (travelling photons) pursuing electrons and high energy photons (in high density) entering to solution. Gold atoms dissociated from the precursor under dissipating heat energy into the solution supplied under propagating photons characteristic current through immersed graphite rod (known in anode). Placing packets of nano shape energy of tuned pulse protocol over compact monolayer assembly comprising transition state atoms develop tiny-sized particles of formed shape. On separation of joint tiny particles into two equilateral triangular-shaped tiny particles, exerting forces of surface format elongate atoms of one-dimensional arrays converting them into structures of smooth elements. Due to immersing level of force, such tiny-shaped particles pack from different zones at centre of light glow where they assembled structures of smooth elements for developing mono-layers of different shapes of particles. Developing one-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from nearly rearward zones of reflection of north-south poles, whereas, developing multi-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from the east-west poles and near regions. Depending on the number of assembled structures of smooth elements at point of nucleation, packing of tiny-shaped particles from different zones develop different shapes of the anisotropic particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles exhibiting unprecedented features are discussed.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

CO₂ geological storage in deep saline aquifers was recently developed at industrial scale mainly in sandstone formations. Experiences on CO₂ injections in carbonates aquifers for permanent trapping are quite limited, mostly from US projects such as AEP Mountaineer, Michigan and Williston Basin. The behavior of fractures in carbonates plays a key role in those reservoirs in which porous matrix permeability is very poor, which drives the CO₂ plume migration through the fracture network where hydromechanics and geochemical effects take place due to injection. Hontomín (Spain) is the actual on-shore injection pilot in Europe (EP Resolution of 14 January 2014), whose reservoir is comprised of fractured carbonates. Existing experiences from field scale tests conducted on site have supported to better understand the behavior of this type of reservoirs for CO₂ geological storage. Innovative CO₂ injection strategies are being carried out in ENOS Project (EU H2020 Programme, http://www.enos-project.eu). First results based on field tests conducted at Hontomín, and the advanced modelling developed so far will be analyzed and discussed in this article, as well as, the description of future works. The evolution of operating parameters such as flow rate, pressure and recovery term during the tests confirm the CO₂ migration through the fractures.

In the work, the nuclei structure was modeled by a system of shells consisting of combinations of spherical and annular vortices. Having connected the spin and the magnetic moments of the nuclei with the dynamics of the outer shell of the nucleus, we determined its type and carried out a semiempirical calculation of the parameters of its structure for stable and unstable nuclear isotopes in the sequence of the order number Z from 1 to 37. Comparison of the obtained nuclear sizes with the radii of the electron shells of atoms made it possible to reveal a definite correlation. On the basis of it, it was concluded that the periodic law of Mendeleyev can determine the patterns in the change in the structure of the atomic nucleus.

In recent years, the discharge of various emerging pollutants, chemicals and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, there are still many gaps despite the great progress in using EO to treat real wastewater. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and another important advanced oxidation technology, PEC, called photoelectrocatalysis (PEC), has shortly been discussed and reviewed. This article showed that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge.

A cosmological model was developed using the equation of state of photon gas, as well as cosmic time. The primary objective of this model is to see if determining the observed rotation speed of galactic matter is possible, without using dark matter (halo) as a parameter. To do so, a numerical application of the evolution of variables in accordance with cosmic time and a new state equation was developed to determine precise, realistic values for a number of cosmological parameters, such as energy of the universe , cosmological constant Λ, curvature of space k, energy density , age of the universe etc. Some assumptions were put forth in order to solve these equations. The current version of the model partially explains several of the observed phenomena that raise questions. Numerical application of the model has yielded the following results, among others: Initially, during the Planck era, at the very beginning of Planck time, , the universe contained a single photon at Planck temperature Planck energy in the Planck volume. During the photon inflation phase (before characteristic time ~10^-9 ), the number of original photons (alphatons) increased at each unit of Planck time and geometrical progression ~n³, where n is the quotient of cosmic time over Planck time . Then, the primordial number of photons reached a maximum of N~10⁸⁹, where it remained constant. It's primordial photons (alphatons) are still present today and represents the essential of the energy contained in the universe via the cosmological constante . Such geometric growth in the number of photons can bring a solution to the horizon problem through exchange and a photon energy volume that is in phase with that of the the volume energy of the universe. The age of the universe in cosmic time that is in line with positive energy conservation (in terms of conventional thermodynamics) and the creation of proton, neutron, electron, and neutrino masses, is ~76 [Gy] (observed . The predicted total mass (p, n, e and n), based on the Maxwell-Juttner relativistic statistical distribution, is ~7x10⁵⁰ . The predicted cosmic neutrino mass is ≤ 8.69x10^-32 (≤ 48.7 ) if based on observations of SN1987A. The temperature variation of the cosmic microwave background (CMB), as measured by Planck, can be said to be partially due to energy variations in the universe (DU/U) during the primordial baryon synthesis (energy jump from the creation of protons and neutrons). In this model, what is usually referred to as dark energy actually corresponds to the energy of the universe that has not been converted to mass, and which acts on the mass created by the energy-mass equivalence principle and the cosmological gravity field, , associated with the cosmological constant, which is high during primordial formation of the galaxies (<1 [Gy]). A look at the Casimir effect makes it possible to estimate a minimum Casimir pressure and thus determine our possible relative position in the universe at cosmic time 0,1813 (t₀/t_W=13,8 /76,1 ). Therefore, from the observed age of 13,8 [Gy], we can derive a possible cosmic age of 76,1 [Gy]. That energy of the universe, when taken into consideration during the formation of the first galaxies (< 1 [Gy]), provides a relatively adequate explanation of the non-Keplerian rotation of galactic masses. Indeed, such residual, non-baryonic energy, when considered in Newton’s gravity equation, adds the term , which can partially explain, without recourse to dark matter, the rotations of some galaxies, such as M33, UGC12591, UGC2885, NGC3198, NGC253, DDO161, UDG44, the MW and the Coma cluster. Today, in the MW, that cosmological gravity force is in the order of 10²⁶ times smaller than the conventional gravity force. The model predicts an acceleration of the mass in the universe (q~ 0,986); the energy associated with curvature is the driving force behind the expansion of the universe, rather than the energy associated with the cosmological constant . An equation to determine expansion is obtained using the energy form of the Friedmann equation relative to Planck power and cosmic time or Planck force acting at the frontier of the universe moving at c. This constant Planck force, from unknown sources, acts everywhere to the expansion of the universe as a stretching effect on the volume. Finally, the model partly explains the value a₀ of the MOND theory. Indeed, a₀ is not a true constant, but depends on the cosmological constant at the time the great structures were formed (~1 [Gy]), as well as an adjustment of the typical mass and dimension of those great structures, such as galaxies. The constant a₀ is a different expression of the cosmological gravity force as expressed by the cosmological constant, Λ, acting through the energy-mass equivalent during the formation of the structures. It does not put in question the value of G.

The aim of this study was to find a correlation between in vivo NIR scan patterns, oxidative status, and blood serum metabolites in rabbits fed diets protected or unprotected against oxidation. Rabbits does in groups of eight were fed for 9 weeks with diets containing linseed, rich in polyunsaturated fatty acids (LS), or linseed plus hazelnut skins, with antioxidant function (LS+HS), and palm oil, rich in saturated fatty acids (PO). The animals were examined at days 1, 31, and 63 using a smart SCÏO molecular sensor, a new miniaturized web-based wireless device, applied to the internal ear flap (NIR range 740-1070 nm). The hazelnut peels integrated diet protected the rabbits from the oxidative stress induced by the addition of unprotected polyunsaturated fats. NIR tomoscopy was variously correlated with serum parameters, lysozyme (R2=0.71), ROMs (0.47), cholesterol (0.49), triglycerides (0.40), and a multivariate Index of Oxidative Risk (0.67 [IOR]). The correlations suggested a close connection between the clustering of the diets according to the laboratory variables and the NIRS scan pattern clustering at the ending trial day, as shown by the highly significant odds ratios. Advantageous use of this simple, painless technique was evident in the planning phase, with no difference among the groups at the beginning of the study, but an effect size that evolved differently over time until the end of the study. In a practical validation of the SCÏO model in 92 commercial rabbit does, the average spread of the predicted IOR was 33% in lactating does (2.54±0.05) vs. dry does (1.91±0.07).

Prionace glauca, blue shark is a cosmopolitan species. Together with Carcharhinus falciformis, it co-dominated the landings of carcharhinidae sharks at the Artisanal Fishing Port of Cotonou. The objective of this study is to determine the demographic parameters of the blue shark in Gulf of Guinea marine waters. The different routines of the FISAT II v 1.2 software associated with the empirical equations of Froese and Nohland, allowed the evaluation of the different demographic parameters of the blue shark in Benin's marine waters. From August to December 2015, 244 individuals shark sizes; ranging from 175cm to 325cm were sampled. The total asymptotic length obtained was 341.25cm with a growth rate of 0.35/year, which indicates that the species is growing rapidly and the optimal total length of the species is 232.01cm. The age of first maturity of the species is 3 years with a longevity of 10 years. The exploitation rate is E= 0.74 with total mortality being 2.4; natural mortality is 0.6 and fishing mortality is 1.8. The sex ratio remains in favour of males throughout the study period. Monitoring programme were suggested with effective management measures established and executed for sustainability of the blue shark’s stock in the Gulf of Guinea.

In order to reveal the mechanism and influencing factors of high pressure jet cavitation of nozzle in submerged environment, this study focused on the evolutionary process of cavitation bubbles and combined finite volume method and mixed multi-phase flow model to analyze the cavitation, velocity distribution and experimental cavitation intensity of fishing net cleaning equipment. Results show that the cavitation inception, growth and collapse mainly occurred in the peripheral region of the flow field. Ring-shaped cavitation erosion zone appeared on the test sample target. A lot of small dense erosion pits were densely distributed in the ring-shaped erosion zone, erosion marks were observed in the center. The cavitation erosion intensity was greatly affected by the nozzle structure. As the diameter of nozzle increased from 0.6 mm to 1 mm, the maximum gas volume fraction increased by 8.53%. The nozzle outlet enlargement angle greatly increased the cavitation intensity. The nozzle with an outlet angle of 30° exhibited the optimal cavitation erosion performance . The cavitation volume fraction of the nozzle with short necking structure was slightly larger than that of the nozzle with long necking structure at the same level in the necking length rang of 3mm to 7mm. In terms of the influence of nozzle structure on the cavitation erosion effect, the nozzle diameter D ranked the first, followed by the outlet angle α, and the necking length L was at the last.

Reading is one of the essential processes during the maturation of an individual. It is estimated that 5-10% of school-age children are affected by dyslexia, the reading disorder characterised by difficulties in the accuracy or fluency of word recognition. There are many studies which have reported that colour overlays and background could improve the reading process, especially in children with reading disorders. As dyslexia has neurobiological origins, the aim of the present research was to understand the relationship between physiological parameters and colour modifications in the text and background during reading in children with and without dyslexia. We have measured differences in electroencephalography (EEG), heart rate variability (HRV), electrodermal activities (EDA), and eye movement of the 36 school-age children (18 with dyslexia and 18 of control group) during the reading performance in 13 combinations of background and overlay colours during the reading task. Our findings showed that the dyslexic children have longer reading duration, fixation count, fixation duration average, fixation duration total, and longer saccade count, saccade duration total, and saccade duration average while reading on white and coloured background/overlay. It was found that the turquoise, turquoise O, and yellow colours are beneficial for dyslexic readers, as they achieved the shortest time duration during the reading tasks when these colours were used. Also, dyslexic children have higher values of beta and the whole range of EEG while reading in particular colour (purple), as well as increasing theta range while reading on the purple overlay colour. We have observed no significant differences between HRV parameters on white colour, except for single colours (purple, turquoise overlay and yellow overlay) where the control group showed higher values for Mean HR, while dyslexic children scored higher with Mean RR. Regarding EDA measure we have found systematically lower values in children with dyslexia in comparison to the control group. Based on present results we can conclude that both colours (warm and cold background/overlays) are beneficial for both groups of readers and all sensor modalities could be used to better understand the neurophysiological origins in dyslexic children.

The risk related to embankment dam breaches needs to be evaluated in order to prepare emergency action plans. The physical and hydrodynamic parameters of the flood wave generated from dam-failure event correspond to various breach parameters such as width, slope and formation time. This study aimed to simulate dam-breach failure scenario of Yabous dam (NE Algeria) and analyze its influence on areas (urban and natural environments) downstream the dam. The simulation was completed using the sensitivity analysis method in order to assess the impact of breach parameters on the dam-break scenario. The propagation of flood wave associated to dam-break was simulated using the one-dimensional HEC-RAS hydraulic model. This study ap-plied a sensitivity analysis of three breach parameters (slope, width, and formation time) in five sites selected downstream the embankment dam. The simulation showed that the maximum flow of the flood wave recorded at the level of the breach was 8768 m3/s, which gradually attenuated along the river course to reach 1579.2m3/s at about 8.5km downstream the dam. This study estab-lished the map of flood-prone areas that illustrated zones threatened with the flooding wave trig-gered by the dam failure due to extreme rainfall events. The sensitivity analysis showed that flood wave flow, height and width revealed positive and similar changes for the increase in adjustments (±25% and ±50%) of breach width and slope in the 5 sites. However, flood wave parameters of breach formation time showed significant trends that changed in the opposite direction compared to breach slope and width.

This paper emphasises on the analogous modelling of hardwood (Acacia) pyrolysis. The effect of physical characteristics of hardwood chips on the pyrolysis is examined through the conservation of solid mass fraction of biomass. The chip size of G30 and G50 are used in the pyrolysis reactor. In the analogous situation, the fixed bed is assumed to be a wooden slab with a porosity equivalent to the voidage of bed. The bulk density, the length of the bed and the porosity are some of the physical attributes of a fixed bed used to determine the variation of solid mass of the hardwood across the fixed bed. The four-temperature sensors separated from each other by 80 mm are used to determine the temperature along the length of the pyrolysis unit. The heating element of 2 kWe is used to initiate the pyrolysis of biomass. The experiments are conducted in three different stages. The ONORM standard chips, G30 and G50, and the combination of them are separately pyrolysis to determine the validity of a model for different sizes of chips. The proposed model is also used to establish the relationship between the kinetics of pyrolysis and decomposition of the hardwood.

Abstract This trial was realized in Yenisehir Vocational School between 2007 and 2008 on the purpose of study out the influence of lack of water in four growth periods of cabbage. In this trial, fourteen irrigation treatments was formed considering the growth periods (establishment, vegetative, yield formation and ripening) of cabbage (Brassicaceae Oleracea var. capitata L. Grandslam F1) and the results obtained from these treatments were evaluated. According to the content of the treatments, the water amount to the plants varied between 0 and 524 mm in the 2007 year, and between 0 and 536 mm in the 2008 year. Water consumption of cabbage in the 2007 year ranged between 200 and 795 mm and in the 2008 year ranged between 190 and 802 mm. Yield, head weight, diameter, height and dry matter ratio were determined statistically important. In 2007 and 2008 years, the maximal yield were found as 74.2 t ha-1 and 72.4 t ha-1 in the E100V100Y100R100 treatments, while the minimal yield were found as 2.0 t ha-1 and 4.0 ha-1 in the E0V0Y0R0 treatments, respectively. Water- yield relationship factor (ky) in 2007 and 2008 years were found as 0.96 and 0.97, respectively.

Evaporation is one of the main processes in the hydrological cycle, and it is one of the most critical factors in agricultural, hydrological, and meteorological studies. Due to the interactions of multiple climatic factors, the evaporation is a complex and nonlinear phenomenon; therefore, the data-based methods can be used to have precise estimations of it. In this regard, in the present study, Gaussian Process Regression (GPR), Nearest-Neighbor (IBK), Random Forest (RF) and Support Vector Regression (SVR) were used to estimate the pan evaporation (PE) in the meteorological stations of Golestan Province, Iran. For this purpose, meteorological data including PE, temperature (T), relative humidity (RH), wind speed (W) and sunny hours (S) collected from the Gonbad-e Kavus, Gorgan and Bandar Torkman stations from 2011 through 2017. The accuracy of the studied methods was determined using the statistical indices of Root Mean Squared Error (RMSE), correlation coefficient (R) and Mean Absolute Error (MAE). Furthermore, the Taylor charts utilized for evaluating the accuracy of the mentioned models. The outcome indicates that the optimum state of Gonbad-e Kavus, Gorgan and Bandar Torkman stations, Gaussian Process Regression (GPR) with the error values of 1.521, 1.244, and 1.254, the Nearest-Neighbor (IBK) with error values of 1.991, 1.775, and 1.577, Random Forest (RF) with error values of 1.614, 1.337, and 1.316, and Support Vector Regression (SVR) with error values of 1.55, 1.262, and 1.275, respectively, have more appropriate performances in estimating PE. It found that GPR for Gonbad-e Kavus Station with input parameters of T, W and S and GPR for Gorgan and Bandar Torkmen stations with input parameters of T, RH, W, and S had the most accurate performances and proposed for precise estimation of PE. Due to the high rate of evaporation in Iran and the lack of measurement instruments, the findings of the current study indicated that the PE values might be estimated with few easily measured meteorological parameters accurately.

We report on the successful preparation of wet dressings hydrogels based on Chitosan-Poly(N-Vinyl-Pyrrolidone)-Poly(ethylene glycol)-Poly(acrylic acid) and Poly(ethylene oxide) by e-beam cross-linking in weakly acidic media, to be used for rapid healing and pain release of infected skin wounds. The structure and compositions of hydrogels investigated according to sol-gel and swelling studies, network parameters, as well as FTIR and XPS analyses showed the efficient interaction of the hydrogel components upon irradiation, maintaining the bonding environment while the cross-linking degree increasing with the irradiation dose and the formation of a structure with the mesh size in the range 11-67 nm. Hydrogels with gel fraction above 85% and the best-swelling properties in different pH solutions were obtained for hydrogels produced with 15 kGy. The hydrogels are stable in the simulated physiological condition of an infected wound and show appropriate moisture retention capability and the water vapor transmission rate up to 272.67 g m-2 day-1, to ensure fast healing. The hydrogels proved to have a significant loading capacity of ibuprofen (IBU), being able to incorporate a therapeutic dose for the treatment of severe pains. Simultaneously, IBU was released up to 25% in the first 2h, having a release maximum after 8h.

During composting process, soils undergo many changes in their physical, chemical and biological properties. Composting has been widely known as an aerobic process during which organic matter is decomposed to humus like substances broken into many organic materials or compounds. The project aims to compare and analyze different combination of composting that yield different properties and nature of soils, and testing their soil physical properties. Dug three compost pits each 1.5 m in depth, labeled compost pit A consisting of potato peels – the only kitchen waste most common around the college hostels, compost pit B consisting of leaf litter and other garden trimmings and compost pit C consisting of cow dung and the other as a controlled experiment with no composting practices.

Iyer Markoulakis Helmholtz Hamiltonian mechanics formalisms mathematically modeled physics with vortex rotational fields acting with gradient fields, typically in zero-point microblackhole general fields. Here, Helmholtz metrics have been gaged to Coulombic Hilbert metrics, representing Gilbertian and Amperian natures of electromagnetic fields out of the mechanical fields from Helmholtz Hamiltonian mechanics. This ansatz general gaging helps to properly isolate field effects – mechanical, electric, magnetic components within the analytical processes. Vacuum gravitational fields and the flavor Higgs-Boson matter inertial gravitational fields have been thus quantified extending to stringmetrics constructs matrix showing charge asymmetry gage metrics, having the power to analyze dark energy superluminal phase, dark matter luminal phase, and light matter subluminal phase. Interpreting particle physics gage matrix pointing to Dirac seas electrons, monopoles with positrons, electron-positron annihilation leading to energy production, relativistic energy generating matter, and both monopoles – vacuum and compressed out of vortex Helmholtz decomposition fields have been interpolated. Quantum ASTROPHYSICS gage metrix posits superluminal profile of signals velocity generating electron-positron chain like “curdling” action that is consistent with physics literature reporting nature electron photon observed oscillatory fields configurations. This helps proposing creation of neutrino antineutrino pair orthogonal to electron positron “curdling” planes, that may lead to formation of protonic hydrogen of stars or orthogonally muon. These aspects will explain receding or fast expanding universe with dark matter in terms of flavor metrics versus gage associating metrics flavor. Additional interpretations of virtual gravitational dipoles that have gravitational charge of opposite signs, reported per physics literature at Planck dimensions, that may originate at the center of supermassive blackhole. On the other hands, vacuum monopoles occur probably at infinity with cosmos extent.

Anaerobic digestion has emerged as an increasingly popular method for the effective management of organic waste and wastewater with the potential to generate renewable energy. However, efficient digestion depends heavily on the complex and diverse microbial communities mediating this process. This review paper delves into the complex microbiome that exists within anaerobic digestion digesters, playing a critical role in the efficient and sustainable conversion of organic waste into biogas. Its primary focus falls within the scope of how various operational and environmental factors, including temperature, pH, hydraulic retention time, substrate loading rates, and the presence of inhibitory compounds, can substantially impact the microbiome of these systems. Through an extensive analysis of the existing literature, the microbial ecology of anaerobic digestion, including the composition and function of the microbial community, their interactions, and responses to different stressors, are evaluated. By offering critical insights into the distribution patterns of active microbial populations upon alterations in various process parameters, a better understanding of the microbial dynamics within these systems is provided, enhancing their efficiency. Overall, this paper emphasizes the importance of unraveling the microbial evolution within AD reactors to optimize biogas production and sustainable waste management and proposes future perspectives in this direction.

The Covid-19 pandemic spreads in waves for a year and a half, despite significant worldwide efforts, the development of biochemical diagnostic methods and population vaccination. One of the reasons for the infection spread is the impossibility of early disease detection through biochemical diagnostics, since biochemical processes slowly develop in a body. At the same time, well known that behavioral characteristics of a person, measured based on reflex movements, are capable for inertialess assessment of psychophysiological parameters. Vibraimage technology is the method of head micromovements video processing by inter-frame difference accumulation and converting spatial and temporal characteristics of the inter-frame difference into behavioral and psychophysiological parameters. Here we shown that behavioral parameters measured by vibraimage changed during COVID-19 infection. The identification of changes signs in behavioral parameters detected by AI trained on patients and controls. The best diagnostic accuracy (higher 94%) obtained using instantaneous values of behavioral parameters measured with the following vibraimage settings: 10Hz frequency of basic measurements; 25 inter-frame difference accumulations and averaging the diagnostic results over period of at least 5 seconds. COVID-19 diagnoses by behavioral parameters showed earlier (5-7 days) detection of the disease compared to symptoms and positive results of biochemical RT-PCR testing. Proposed method for COVID-19 diagnosis indicates infected persons within 5 seconds video processing using standard television cameras (web, IP) and computers, allows mass testing/selftesting and will stop the pandemic spread. We assume that head micromovements analysis for diagnosis of various diseases is possible not only with the help of vibraimage technology. Further research of human head micromovement analysis will help stop the COVID-19 pandemic and will contribute to the development of new contactless and environmentally friendly methods for early diagnosis of diseases.

Groundwater is a vital resource for human welfare. However, due to various factors, groundwater pollution is one of the main environmental concerns facing. Yet, it is challenging to simulate groundwater quality dynamics due to the insufficient representation of nutrient percolation processes in the soil and Water Assessment Tool model. The objectives of this study were extending the SWAT module to predict groundwater quality. The results proved a linear relationship between observed and calculated groundwater quality considering No3 and TDS with R2, NSE and PBIAS values in the satisfied ranges, albeit underestimation and overestimation were observed due to limited data availability. These results highlight that nitrate and TDS concentrations and variability in groundwater may used as a tool in surface water quality that have to be assumed for designing adaptive management scenarios. Hence, extended SWAT model could be a powerful tool for future regional to global scale modelling of nutrient loads supporting effective surface and groundwater management.

Identification of the differentially-expressed genes is important for clarification of the complex molecular mechanisms under drought conditions. In this experiment, transcriptome profiles of sensitive and tolerant tomato genotypes under drought stress were analyzed. Three up-regulated genes were selected, included CAB3 (Chlorophyll a-b binding protein3), SAMDC (S-adenosylmethionine decarboxylase proenzyme), and ACS9 (1-aminocyclopropane-1-carboxylate synthase 9). After bioinformatics analysis, tomato genotypes were subjected to drought stress and gene expression was determined using Real-Time-PCR. Physiological parameters of genotypes were also measured by spectrophotometer-based methods. According to the results, these three genes play a key role in stress tolerance. Expression of the CAB3 gene in both sensitive and tolerant genotypes was not significantly different compared to the control, but the SAMDC gene decreased in both genotypes and the ACS9 gene decreased in sensitive genotype and increased in tolerant genotype. The physiological analysis also showed that under stress conditions, the photosynthetic system of the plant was disrupted and the chlorophyll content was reduced, but, proline content and antioxidant enzymes activity increased, in which their quantity in the tolerant genotype was significantly higher than sensitive. Under drought stress, due to damage to the lipid membrane, Malondialdehyde content also increased, in which the sensitive genotype was more affected.

Acid fracturing simulation is used widely to optimize carbonate reservoirs and improve acid fracturing treatment performance. In this study, a method was used to minimize the risk of the acid fracturing treatment. First, optimal fracture geometry parameters with UFD methods are calculated. After that, design components change as long as fracture geometry parameters reach their optimal values. The results showed a high flow rate needed to achieve optimal fracture geometry parameters with increasing acid volume. Sensitivity analysis was performed on controllable and reservoir parameters. It observed that a high flow rate should be applied for a low fluid viscosity to achieve the optimization goals. Straight acid reaches optimal conditions at a high flow rate and low volume. These conditions for retarded acids appear only at a low flow rate and high volume. The study of the acid concentration for gelled acid showed that as it increased, the flow rate and volume increased. Besides, for low permeability formation, a large fracture half-length and small fracture width are desirable. In this case, a higher flow rate will be required. The sensitivity analysis showed that the optimum flow rate and acid volume increase and decrease for the high Young's modulus. The effect of closure stress was also investigated and observed for a sample with high closure stress, low flow rate, and high acid volume are required.

The textbook analysis of vacuum energy density (VED) in flat spacetime follows from Pauli’s lectures of 1951, in which quantum vacuum is modeled as a reservoir of free harmonic oscillators. In his lectures, Pauli shows that deriving a nearly vanishing VED is contingent upon fulfilling three corollary conditions called polynomial-in-mass-constraints. The goal of this work is to evaluate Pauli’s constraints against the Standard Model parameters and the Higgs mechanism of spontaneous symmetry breaking.

The experimental results of forces and efforts derived from the opening of incisions in the orbital cavity in a pig’s head are presented in this article. The different areas of the incision openings are related to the needs at the incision procedure for a dacryocystorhinostomy. In terms of the experimental procedure, an origin and a plane are defined so as to allow the location of the opening of the incision. The incisions are retracted along an axis of said origin. This procedure has been based on the mathematical model developed for this work, which consists of a procedure for determining the behavior of an incision when a force is applied to retract the skin. The experimental data obtained, suggests the existence of an almost linear relationship between the increment of resistance in relation to the time obtained for each opening, the same of which is deemed to be consistent with the behavior of an elastic material.

Recent advancements of computer and electronic systems have motivated the extensive use of intelligent systems for automation of agricultural industries. In this study, the temperature variation of the mushroom growing room is modeled through using a multi-layered perceptron (MLP) and radial basis function networks. Modeling has been done based on the independent parameters including ambient temperature, water temperature, fresh air and circulation air dampers, and water tap. According to the obtained results from the networks, the best network for MLP is found to be the second repetition with 12 neurons in the hidden layer and 20 neurons in the hidden layer for radial basis function networks. The obtained results from comparative parameters for two networks showed the highest correlation coefficient (0.966), the lowest root mean square error (RMSE) (0.787) and the lowest mean absolute error (MAE) (0.02746) for radial basis function. Therefore, the neural networks with radial basis function was selected as the optimal predictor for the behavior of the system.

We have shown that the use of evolutionary gravitational constants G, the speed of light c, and cosmological constant Λ in the Einstein’s field equations leads to a very simple model that fits the supernovae Ia data with a single parameter as well as the standard ΛCDM model with two parameters, and has the predictive capability superior to the latter. We have shown that at the current time G and c both increase as dG/dt = 5.4GH₀ and dc/dt = 1.8cH₀ with H₀ as the Hubble constant, and Λ decreases as dΛ/dt = −1.2ΛH₀. Negative finding on the variation of G with time derived from the analysis of lunar laser ranging data in several studies has been attributed to the fact that these studies did not consider the variation of c simultaneously with G.

This study investigates the use of programming language Python to analyse and model chemical engineering processes. Using municipal sewage sludge (MSS) drying as an example, the study demonstrates how Python can support analyses and model drying data. The drying process was performed on a flat plate while maintaining a uniform, parallel drying air speed of 1.15 m s-1. The Python program helped to analyse the digitalised weight measurements from each sample. The program enables sorting input data, determining the drying critical point and evaluating the first and second drying periods.

We report the effect of doping Cd1-xZnxS/ZnS core/shell quantum dot (CSQDs) in nematic liquid crystal p-methoxybenzylidene p-decylaniline (MBDA) at 0.05 wt/wt%, 0.1 wt/wt%, 0.15 wt/wt%, 0.2 wt/wt%, 0.25 wt/wt% and 0.3 wt/wt% concentrations of CSQDs in MBDA. Dielectric parameters with and without bias with respect to frequency has been investigated. The change in electro - optical parameters with temperature has also been demonstrated. The increase in the mean dielectric permittivity has been found due to large dipole moment of CSQDs which impose stronger interactions with the liquid crystal molecules. The dielectric anisotropy changes sign on doping CSQDs in MBDA liquid crystal. It was concluded that the CSQDs doping noticeably increases the dielectric permittivity of nematic MBDA in the presence of electric field. The doping of CSQDs in nematic MBDA liquid crystal reduces the ion screening effect effectively. This phenomenon is attributed to the competition between the generated ionic impurities during assembling process and the ion trapping effect of the CSQDs. The rotational viscosity of nematic liquid crystal decreases with increasing concentration of the CSQDs with faster response time observed for 0.05 wt/wt% concentration. The birefringence of the doped system increases with the inclusion of CSQDs in MBDA. These results find application in the field of display devices, phase shifters, industries and projectors.

An improved FSM method is used in geophysical and environmental corrections to enhance the final product of the along track Jason-2 SLA data and extend it near the Red Sea borders. In this study the ionospheric correction range, wet tropospheric correction range, sea state bias correction range and dry tropospheric correction range are enhanced and improved using FSM01, which helped to retrieve three more tracks (106, 170 and 234), earlier neglected by the distribution centers, and extend the tracks towards the coast. The FSM01 SLA is compared with Jason-2 SLA and AVISO SLA for the available 5 tracks, in which the FSM01 SLA show a good agreement and higher correlation with the Jason-2 SLA compared with that of AVISO, in addition to that it fills the gaps in the times series of all tracks. The new retrieved tracks also compared with those retrieved by AVISO, both data show similar variability, with FSM01 SLA show no gaps in the time series. The FSM01 SLA also extended towards the coast and show high correlation with the coastal tide measurements.

Abstract: Background: Exposure to ETS (Environmental Tobacco Smoke) is one of the most toxic environmental exposures. Objective: To investigate the impact of ETS on physiological, biochemical, psychological indicators, on the urine antioxidant capacity (AC) and oxidative damage to lipids in a pilot sample of healthy pregnant women. Methods: The exposure to ETS was investigated by a validated questionnaire, urine cotinine and the marker of oxidative damage to lipids - 8-isoprostane concentrations using an ELISA kit. Urine AC was determined by the spectrophotometric TEAC method. From the sample of pregnant women (n=319, average age 30.84 ± 5.09 years) in 80 the levels of cotinine and oxidative stress markers were analyzed. Results: From our sample, 5 % individuals (7.4 % objectified by cotinine) were current smokers and 25 % reported passive smoking in the household (18.8 % objectified by cotinine). The Kappa was 0.78 for smokers and 0.22 for ETS exposed non-smokers. Smokers as well as non-smokers had significantly higher (p<0.05) urine AC than ETS exposed non-smokers. Non-smokers had significantly lower levels of 8-isoprostane than smokers (p<0.01) and ETS-exposed non-smokers (p<0.05). Correlations between urine levels of cotinine and AC were positive in ETS exposed non-smokers. Conclusion: The harmful effect of active and passive smoking on oxidative stress parameters has been indicated.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

The current paper aims to study the impact properties of additively manufactured Maraging steel (1.2709) using laser powder bed fusion (PBF-L) processing. The specimens were manufactured using 3Dsystems ProX 300 equipment under constant specific power input, or Andrew Number. The interactions between the build strategy and parameters, such as Hatch spacing and Scan speed was, and the impact strength and fracture were investigated. The Impact energy anisotropy was also investigated parallel and perpendicular to the build direction. Instrumented impact testing was performed, and the fractography supported that the fusion zone geometry dictated the fracture behaviour. The influence from gaseous elements such as Nitrogen, Oxygen and Hydrogen was found insignificant at the levels found in the printed material.

This research takes Cuiwei Village in Qianshan District of Zhuhai City as an example. Through field research, the village is investigated and analyzed, and the street scale, spatial structure, functional characteristic streets, internal commercial distribution forms, and functions of Cuiwei Historic District are studied. analysis. On this basis, based on the convex space method and the line-of-sight analysis method in the space syntax theory, with the help of Depthmap software, the complex street node, that is, the space of the two nodes A and B, is established through the establishment of a visual field model. It includes the analysis of the integration degree of the horizon, the concentration of the horizon, the connection value of the horizon and the spatial characteristics of the historical area, as well as the traditional buildings that are the most representative of the village, namely the Three Kings Temple and the Webster's Mansion. When R=N and radius R=3, observe the changes in the two parameters of the visual integration and visual depth of the two historical buildings. And with the help of Baidu Time Machine photos in different periods to observe and record the changes in the store and the characteristics of people's behavior, and draw conclusions.

The impact of nutrients on the environment, particularly on water bodies, has led to extensive studies for nutrient control. Within this context, studies have been focused on source separation of human urine from domestic wastewater to recover nutrients. Potassium is one of the most important components of human urine. However, data on potassium removal or recovery are quite limited except for some indirect information through use of zeolites for mostly ammonia removal. Potassium struvite or K-struvite (MgKPO₄·6H₂O) is a sparingly soluble salt belonging to struvite and has the potential of being used as a means of potassium and phosphate recovery from segregated human urine. This study aimed to assess the potential of K-struvite precipitation for control and recovery of nutrients. Within this context, K-struvite precipitation experiments were performed on both synthetically prepared samples and synthetic human urine solution to determine effect of operation parameters i.e. pH, stoichiometry, and temperature on potassium recovery performance. Results indicated that process performance as well as type of solid phases co-precipitated with K-struvite were closely related to initial potassium concentration, pH and reaction stoichiometry. At pH 10, the potassium recovery efficiency was maximized up to 87% by application of 100% excess dose of Mg and P for both synthetic samples and synthetic human urine solution. On the other hand, application of excess dose of K did not provide any improvement in K recovery efficiency. The effect of temperature on solubility of K-struvite was insignificant at the temperature of 24-90°C. Solid phase analyses confirmed that K-struvite was co-precipitated with either Mg₃(PO₄)₂, MgNaPO₄·7H₂O, or MgHPO₄·7H₂O depending on pH and stoichiometry instead of a pure compound.

Urban vitality, understood as a key factor for the achievement of cities’ sustainability, shows a strong relationship with urban morphology. The city theorist Jane Jacobs suggested morphologi-cal aspects to promote vital cities already in the 1960s, which remain valid in the present. How-ever, few studies in the Andean region quantitatively exemplify this. This paper aims to test the measurement of urban vitality in a neighborhood of Quito, Ecuador, called La Mariscal, inte-grating Jacobs’ approach. In particular, three urban vitality indexes are evaluated with the appli-cation of GIS software using cadastral data obtained from the municipality and field data col-lection. Results show that the context-based previous knowledge and the scale of analysis are es-sential factors in the configuration of dimensions, indicators, and spatial representation of any urban vitality index. In the study area land use mixture, contact opportunity, and accessibility dimensions are fundamental. Regarding indicators, the incorporation of the informal small-scale commerce, the quality of sidewalks, the street slope, and the good-conditioned street furniture is recommended. Finally, a hybrid representation (raster and vectorial) is suggested to precisely measure urban vitality at a block scale. Altogether, by providing a comparative approach, we in-tend to bring a useful framework for researchers and planners to study urban vitality in Andean cities.

This paper analyzes the robust dissipativity of uncertain stochastic generalized neural networks (USGNNs) with Markovian jumping parameters and time-varying delays. In practical applications most of the systems refer to uncertainties, hence, the norm-bounded parameter uncertainties and stochastic disturbance are considered. Then, by constructing an appropriate Lyapunov-Krasovskii functional (LKF) and by employing integral inequalities LMI-based sufficient conditions of the considered systems are established. Numerical simulations are given to show the merit of the presented results.

We have shown that our varying physical constant model is consistent with the recently published variational approach wherein Einstein equations are modified to include the variation of the speed of light c, gravitational constant G and cosmological constant Λ using the Einstein-Hilbert action. The general constraint resulting from satisfying the local conservation laws and contracted Bianchi identities provides the freedom to choose the form of the variation of the constants as well as how their variations are related. When we choose dG/Gdt=3dc/cdt, ̇the same as in our quasi-phenomenological model, c=c₀ exp⁡(a^α-1), G=G₀ exp⁡[3(a^α-1)] and Λ=Λ₀ exp⁡[(a^-α-1)], where a is the scale factor and α=1.8, we are able to confirm the success of our the model in explaining three astrometric anomalies and the null results on the variation of G and the fine structure constant. We show that the model: (a) fits the supernovae 1a observational data better than the ΛCDM model; (b) determines the first peak in the power spectrum of the cosmic microwave background temperature anisotropies at multipole value of l=217.3; (c) calculates the age of the universe as 14.1 Gyr; and (d) finds the BAO acoustic scale to be 145.2 Mpc. These numbers are within less than 3% percent of the observed values and the values obtained by the ΛCDM model. Surprisingly we find that the dark-energy density is negative in a universe that has significant negative curvature and whose expansion is accelerating at a faster rate than predicted by the ΛCDM model.

Longitudinal dispersion coefficient (LDC) plays an essential role in modeling the transport of pollution and sediment in the natural rivers. As a result of transportation processes, the concentration of pollution changes along the river. Different studies have been conducted to provide simple equations for estimating LDC. In this study, Support Vector Regression (SVR), Gaussian Process Regression (GPR), M5P and Random Forest (RF) examined to predict the LDC in the natural streams. The hydraulic and geometric features of different rivers gathered for developing the mentioned models for LDC estimation and various statistical criteria were utilized to scrutinize of the models. Furthermore, the Taylor chart was used to evaluate the models and achieved results showed that among machine learning models, M5P displayed the superior performance with CC of 0.823, SI of 0.812, NS of 0.577 and WI of 0.879. As well, S-D model with CC of 0.795 SI of 0.827, NS of 0.558 and WI of 0.890 had more precise results than other empirical models. The results indicates that the developed M5P model with simple formulations was superior to other machine learning models and empirical models and therefore, it can be used as a proper tool for estimating LDC in natural rivers.

Laser marking on polymer composite surfaces can be difficult to contrast and cause readability problems for electronic decoding equipment on production lines due to poor interaction between the laser and the fibres used to reinforce these materials. This problem can be solved with the right choice of marking parameters, resulting in savings for companies by avoiding production problems such as rejection, scrap and customer complaints. The present work uses the PBT/glass fibre composite used in the manufacture of instrument panels for motorcycles. The tests were carried out with different laser marking parameters using a Nd: YAG laser. Subsequently, the laser-marked DMC codes were analysed using a Verifier to evaluate the quality according to the ISO/IEC 29158:2020 standard. A detailed analysis of these surfaces was also carried out to observe some physical and chemical changes using SEM microscopy and EDS spectroscopy. The optical analysis showed that the lower the radiation power and pulse frequency and the higher the marking speed, the weaker the laser marking and therefore the poorer the DMC code quality, which was confirmed by the SEM. EDS spectroscopy showed that the laser marking process did not affect the chemical changes on the sample surface.

The main aim of this study is to investigate the optimization of the technological process for selective laser melting (SLM) additive manufacturing. The group of process parameters considered was selected from the first-stage parameters identified in preliminary research. Samples manufactured using three different sets of parameter values were subjected to static tensile and compression tests. The samples were also subjected to dynamic Split–Hopkinson tests. To verify the microstructural changes after the dynamic tests, microstructural analyses were conducted. Additionally, the element deformation during the tensile tests was analyzed using digital image correlation (DIC). To analyze the influence of the selected parameters and verify the layered structure of the manufactured elements, sclerometer scratch hardness tests were carried out on each sample. Basing on the research results it was possible to observe the porosity growth mechanism and its influence on the material strength (including static and dynamic tests). Parameters modifications that caused 20% lower energy density, elongation of the elements during tensile testing decreased twice, which was strictly connected with porosity growth. An increase of energy density by almost three times caused a significant reduction of force fluctuations differences between both tested surfaces (parallel and perpendicular to the building platform) during sclerometer hardness testing. That kind of phenomenon had been taken into account in the microstructure investigations before and after dynamic testing where it had been spotted a positive impact on material deformations based on fused material grains formation after SLM processing.

Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft-switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

Here, we propose a novel scheme based on advanced techniques of digital modulation in optical communications to achieve a single-channel transmission rate above 100 Gb/s. We utilize a hybrid scheme amplitude/phase/frequency/dual polarization, combined with multidimensional dual lattice and a low-density parity-check-coded modulation. The Stokes parameters are applied to the proposed scheme to map the four-dimensional classical polarization \({I_X},{Q_X},{I_Y},{Q_Y}\) in a three-dimensional space. In addition, in the proposed system, the packing theory is applied to the bit interleaver process, three wavelengths are packaged before being transmitted over a wavelength-division multiplexing optical channel. This modulation process is carried out using symmetrical geometric shapes, such as a hypercube or a polyhedron, based on the molecular links theory using a grouping of 12 and 13/15 bits for the cubic and spherical lattices, respectively. The proposed technique is evaluated in the context of long distance communications over distances up to 100 km. The bit error rate results showed that the optical signal-to-noise ratio was approximately 4 dB over a distance of 50 km. In addition, the power spectral efficiency was found to be 3 lambda, which is considered good performance considering the effects of distance and the non-linear effects influencing the number of lambdas. Also, we use an optical time division multiplexing scheme (OTDM) in order to achieve a transmission rate beyond 1Tbit/s, where the speed effect is evaluated, taking into consideration that the power spectral efficiency is degraded. Furthermore, the average noise floor is -60dBm for all transmission distances. These findings are expected to contribute to the future implementation of robust long-distance optical communication infrastructure.

This paper examines the influence of physical parameters on the collapse dynamics of a spherical bubble filled with diatomic gas ($\kappa=7/5$). The present numerical investigation shows that each physical parameter affects the bubble collapse dynamics differently. After comparing the contribution of each physical parameter, it appears that, of all the parameters, the surrounding liquid environment affects the bubble collapse dynamics the most. Meanwhile, surface tension has the weakest influence and can be ignored in the bubble collapse dynamics. However, surface tension must be retained in the initial analysis since this, as well as the pressure difference jointly control initial bubble formation. As an essential part of this study, a general Maple code is provided.

This study evaluated eight herbal and fruit teas to produce kombucha beverages. Besides, the effect of initial sucrose concentration (10, 40, and 70% w/v) on kombucha fermentation from tea extracts was investigated. Kinetic characterization and modeling of kombucha fermentation were also performed. Results showed that kombucha beverages' characteristics and chemical content changed according to tea type and initial sucrose concentration. It was determined that as initial sucrose concentration increased, the consumed substrate concentration increased. The highest total biomass values were determined when green tea and pomegranate tea were supplemented with 70 g/L sucrose. The highest total phenolic content and antioxidant activity were achieved with green tea samples. The total acidity and phenolic substance concentration increased as fermentation progressed in general. The kinetic parameters including maximum consumption rate, sugar utilization, yield, biomass yield, maximum biomass, total acidity, phenolic production rate, and the phenolic result were computed depending on changing substrate concentration. Concerning kinetic modeling, proposed models (Logistic and Luedeking-Piret models) estimated satisfactorily experimental substrate consumption and total acidity values. Besides, total acidity was associated with the substrate consumption.

With the aim to investigate the effect of parameter and quenching process on the joint of hot stamping steel by laser welding, the BR1500HS boron steel was welded by filling-wire laser welding with ER70-G welding wire under different parameters. The welded specimens were heated to 900℃ and held for 5min before water quenching. The universal material test machine, Optical micro-scope, Vickers hardness tester, scanning electron microscope and electron backscatter diffraction (EBSD) were used to characterize. The results showed that the macroscopic morphology of fusion zone (FZ) becomes from funnelform to hyperbolic curve shape when heat input increases and from hyperbolic curve shape to funnelform when wire-feed speed increases. The strength after quenching is more than 1557Mpa at heat input of 1040J/cm, wire feeding speed of 1.6m/min~1.8m/min and welding speed of 1.5m/min. EBSD test showed that the FZ and fine grain zone (FGZ) have more retained austenite (RA) than coarse grain zone (CGZ) before quenching and RA in FZ and heat affect zone (HAZ) decreased and distributed uniformed after quenching. The grain diameter in FZ distribute unevenly, with the maximum grain diameter larger than 40μm before quenching. After quenching, the grain diameter of FZ, HAZ and BM is more even and coarse grains in the FZ was refined. Before quenching, the microhardness of FZ and HAZ is of 450HV~500HV at different heat input and wire-feed speed and all region of joint keeps at 450HV~550HV after quenching. Most dimple and little river pattern in the joint fracture mor-phology before quenching indicates a well plasticity and most cleavage facet is observed after quenching due to the joint combine with martensite.

The study takes into account different classes of tunnel boring machines (TBMs), with the aim of identifying correlation models which are meant to estimate, at a preliminary design phase, the construction time of a tunnel and to evaluate the mechanical and operational parameters of the TBMs, starting from the knowledge of the tunnel length and/or the excavation diameter. To achieve this goal, first of all a database was created, thanks to the collection of the most meaningful technical parameters from a large number of tunnels; afterward, it was statistically analysed through Microsoft Excel. In a first phase, forecasting models were identified for the three types of machines investigated, separately for compact rocks (open TBM) and fractured rocks (single and double shield TBM). Then, the mechanical parameters collected through the database were analysed, with the aim of obtaining models that take into account, in addition to the type of TBM, the geological aspect, and the type of rock characterising the rock mass. Finally, the validation of the study was proposed in a real case, represented by the Moncenisio base tunnel, a work included in the new Turin–Lyon connection line. The estimated values were compared with the real ones, in order to verify the accuracy of the experimental models identified.

Natural systems of units $\{U_i\}$ need to be overhauled to include the dimensionless coupling constants $\{\upalpha_{U_i}\}$ of the natural forces. Otherwise, they cannot quantify all forces in a unified manner. Thus, each force must furnish a system with at least one dimensional and one dimensionless constant. We revisit three natural systems of units (atomic, cosmological, and Planck). The Planck system is easier to rectify, and we do so in this work. The atomic system discounts $\{ G, \upalpha_G \}$, thus it cannot account for gravitation. The cosmological system discounts $\{ \slashed{h}, \upalpha_\slashed{h} \}$, thus it cannot account for quantum physics. Here, the symbols have their usual meanings; in particular, $\upalpha_G$ is the gravitational coupling constant and $\upalpha_\slashed{h}$ is the fine-structure constant. The speed of light $c$ and the impedance of free space $Z_0$ are resistive properties of the vacuum, thus they must be present in all systems of units. The upgraded Planck system $${\rm UPS} \,:=\,\{ c, Z_0, G, \upalpha_G, \slashed{h}, \upalpha_\slashed{h}, \,\dots\,\!\},$$ describes all physical scales in the universe---it is nature's system of units. As such, it reveals a number of properties, most of which have been encountered previously in seemingly disjoint parts of physics, and some of which have been designated as mere coincidences. Based on the UPS results, that relate (sub)atomic scales to the Planck scale and the fine-structure constant to the Higgs field, we can state with confidence that no observed/measured physical properties are coincidental in this universe.

The data from the extended system was recorded on-going basis in the archives of the monitoring system, and the multipoint system was directly stored in the methane-anemometers, which allows one to perform a comparative analysis of the obtained records from many methane detectors. An important element of the analyses was the simultaneous registration of the methane concentration in the longwall, together with information on operating time, direction of shearer operation and type of work: mining/cleaning. Mining practice shows that in methane coal mines, methane is often the basic limitation for modern and high-efficiency longwall complexes. The paper reports on selected observations and tests carried out in the Cw-4 longwall in seam 364/2 of the Budryk mine belonging to JSW SA. In observation of the methane level in the Cw-4 longwall, additional sensors installed in the end part of the longwall from the side of the gobs and registration of air velocity and methane concentration in the multipoint system built in the selected longwall cross-section were used, regardless of the air parameters recorded in the monitoring system.

High molecular weight glutenin subunits (HMW-GS) and Low molecular weight glutenin subunits (LMW-GS) in mature grains play important roles in the formation of glutenin macropolymer and gluten quality. To characterize the expressed glutenin genes of the bread wheat variety Xinmai 26 during seed development, in this study, we measured the dough rheological properties of mature grains through farinograph and gluten testing system, and revealed its strong gluten quality. The compositions of HMW-GS and LMW-GS were analyzed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS). Further, a total of 18 full-length transcripts were obtained by third-generation RNA sequencing, including 5 transcripts of HMW-GS genes and 13 transcripts of LMW-GS genes (8 intact genes and 5 pseudogenes). The deduced protein structures of transcript sequences exhibit the typical HMW-GS and LMW-GS structural characteristics. Moreover, a specific functional marker was developed to make better use of the extra cysteine residue of 1Dx5 subunit. This study provides an efficient method to accurately identify glutenin genes in bread wheat through matching full-length transcripts to their spectrum of glutenin, which will be helpful to understand the contributions of glutenin genes to wheat quality.

Electrospinning is a simple versatile method to generate nanofibres. Remarkable progress has been made in the development of electrospinning process. The production of nanofibers is affected by many parameters, which influence the final material properties. Electrospun fibers have a wide range of applications such as energy storage and biomedical scaffolds. Polyacrylonitrile (PAN) has been widely used in the production of carbon nanofibers. PAN has received increasing interest in recent years, due to its excellent characteristics, such as spinnability, biocompatibility, and commercial viability, opening new applications in the biotechnological field. This paper provides an overview of the electrospinning process, its main parameters, and operation modes that affect nanofibers fabrication. A review of their biological applications is proposed. A focus is made on PAN fibers formation, functionalization, and application as scaffolds to allow cell growth. Overall, nanofibre scaffolds, made of stabilized PAN, appear as a powerful tool in medical applications needing controlled cell culture.

Today, there is a time series analysis that has gained significant popularity across various industries to provide effective solutions for any specific challenges. Artificial intelligence logic is generally used to solve time-series problems with the help of various frameworks that are available for the development of AI-based applications. Currently, there is a significant framework in Python that is driven by its comprehensive libraries and their practical implementations. Time series analysis can be built with the help of some specific models that give results to differentiate the efficiency and domains of great work. This paper focuses on three diverse libraries of Python to predict the Gulf stock exchange market. These libraries are prediction models that are helpful in predicting future values. These models utilized include SARIMA (Seasonal Auto-Regressive Integrated Moving Average), Neural Prophet Model, and Fb Prophet model. Each model is trained using the provided datasets, which are followed by evaluation parameters such as MSE, RMSE, recall, MDAPE, accuracy, precision, etc. The main purpose of using these three models for stock market prediction is to find the better-suited models. In the past few decades, the stock market industry has seemed to have promising growth after 2022 onwards. This paper will help us make a significant decision about model usage for addressing such complex challenges. Especially, the research findings indicate that all three models demonstrate in different domains. SARIMA can perform well in overall prediction tasks, while the Prophet model works great with smaller datasets that contain seasonality trends.

Wireless cellular communication technology has developed into a very resourceful commodity worldwide. Today, people of all races can hardly live without means of voice and data cellular communication technology. Imprecise propagation loss estimation leads to high power waste, high co-channel interference and poor service quality in cellular communication system networks. This paper proposes a realistic adaptive fine-tuning method for distinctive propagation loss estimation over a microcellular communication radio links based on signal power measurements from Long Term Evolution radio broadband networks, taking non-line of sight (NLOS) and line of sight (LOS) environments into consideration. The methodology is verified by measurements taken in non-line of sight and line of sight signal propagation scenarios. The results showed that the estimated propagation losses using the proposed realistic adaptive tuning models were more accurate than the existing Cost -231 modelling estimation approach.

The design flood concept (DF) provides for an essential tool in designing the hydraulic works, in defining the reservoir operation programs and for a reliable flood hazard identification. Under a simplified approach, the maximum discharge and the floods volume are statistically processed to reasonably define the DF. Yet, the integral hydrograph provides additional key temporal and quantitative details of important significance for flood management and particularly for the res-ervoirs operation and associated risks of failures. The procedure presented in this paper (as applied on a set of compatibly shaped hydrographs) involves the following key stages: (i) normalize the floods, (ii) define similar flood shape classes and (iii) evaluate the average dimensionless flood (ADF) for each class. The ADFs are finally transformed into a set of (DF)s. Many statistical distributions approximate acceptably the frequent values of the maximum discharges or the flood volumes, yet displaying a significant spread for medium or rare probabilities of exceedance (PE). This scattering, which can be explained by the epistemic uncertainty, defines an area of uncertainty both for measured and extrapolated values. In considering upper and lower values of the uncertainty in-tervals as limits for maximum discharges and flood volumes, then by combining them compatibly, a set of DFs - as completely defined hydrographs, with different shapes - results for each PE. The herein proposed procedure defines both one peak DF and multi-peaks DF. Subsequently, such DFs do assist water managers in examining and establishing tailored approaches for a variety of input hydrographs. Among the DFs that would correspond to a same PE, the most compact floods arise a special interest, for they are basic in defining the set of safe operation rules for hydraulic structures.

We propose a model for gravity based on the gravitational polarization of space. With this model, we can relate the density parameters within the Friedmann model, and show that dark matter is bound mass formed from massive dipoles set up within the vacuum surrounding ordinary matter. Aggregate matter induces a gravitational field within the surrounding space, which reinforces the original field. Dark energy, on the other hand, is the energy density associated with gravitational fields both for ordinary matter, and bound, or induced dipole matter. At high CBR temperatures, the cosmic susceptibility, induced by ordinary matter vanishes, as it is a smeared or average value for the cosmos as a whole. Even though gravitational dipoles do exist, no large scale alignment or ordering is possible. Our model assumes that space, i.e., the vacuum, is filled with a vast assembly (sea) of positive and negative mass particles having Planck mass, called planckions, which is based on extensive work by Winterberg. These original particles form a very stiff two component superfluid, where positive and negative mass species neutralize one another already at the submicroscopic level, leading to zero net mass, zero net gravitational pressure, and zero net entropy, for the undisturbed medium. It is theorized that the gravitational dipoles form from such material positive and negative particles, and moreover, this causes an intrinsic polarization of the vacuum for the universe as a whole. We calculate that in the present epoch, the smeared or average susceptibility of the cosmos equals, , and the overall resulting polarization equals, . Moreover, due to all the ordinary mass in the universe, made up of quarks and leptons, we calculate a net gravitational field having magnitude, . This smeared or average value permeates all of space, and can be deduced by any observer, irrespective of location within the universe. This net gravitational field is forced upon us by Gauss’s law, and although technically a surface gravitational field, it is argued that this surface, smeared value holds point for point in the observable universe. A complete theory of gravitational polarization is presented. In contrast to electrostatics, gravistatics leads to anti-screening of the original source field, increasing the original value, , to, , where is the induced or polarized field. In the present epoch, this leads to a bound mass, , where is the sum of all ordinary source matter in the universe, and equals the relative permittivity. A new radius, and new mass, for the observable universe is dictated by the density parameters in Friedmann's equation, and Gauss’s law. These lead to the very precise values, , and, , respectively, somewhat larger than current less accurate estimates.

The mechanisms of natural oscillations and resonance are described, considering the peculiarities of the transformation of elastic and kinetic energy in the implementation of the law of conservation of energy in local and integral volumes of the body, using the concept of mechanics based on the concepts of space, time and energy. When describing the motion in the Lagrange form, the elastic deformation energy of the particles is determined by the quadratic invariant of the tensor, whose components are the partial derivatives of Euler variables with respect to Lagrange variables. The increment of the invariant due to elastic deformation is represented as the sum of two scalars, one of which depends on the average value of the relative lengths of the edges of the particles in the form of an infinitesimal parallelepiped, the second is equal to the standard deviation of these lengths from the average value. It is shown that each of the scalars can be represented in the form of two dimensionless kinematic parameters of elastic energy, which participate in different ways in the implementation of the law of conservation of energy. One part of the elastic energy passes into kinetic energy and participates in the implementation of the law of conservation of energy for the body as a whole, considering external forces. The second part is not converted into kinetic energy but changes the deformed state of the particles in accordance with the equations of motion while maintaining the same level of the part of the elastic energy of the particles used for this. The kinematic parameters differ from the volume density of the corresponding types of energy by a factor equal to the elastic modulus, which is directly proportional to the density and heat capacity of the material and inversely proportional to the volume compression coefficient. Transverse, torsional, and longitudinal vibrations are considered free and under resonance conditions. The mechanisms of transformation of forced vibrations into their own after the termination of external influences and resonance at the superposition of free and forced vibrations with the same or similar frequency are considered. The formation of a new free wave at each cycle with an increase in the amplitude, which occurs mainly due to internal energy sources, and not external forces, is justified.

Plant stem cell cultures have so far been established in only a few plant species using cambial meristematic cells. The presence of stem cells or stem cell-like cells in other organs and tissues of the plant body, as well as the possibility of de novo generation of meristematic cells from differentiated cells, allows to consider the establishment of stem cell cultures in a broader range of species. Therefore, this study aimed to establish a stem cell culture of the medicinal plant Calendula officinalis L. Callus tissues were induced from explants taken from leaves and roots. Appropriate combinations of plant growth regulators and light parameters for in vitro cultivation were selected. Already at this stage, stem and dedifferentiated cells could be identified, and cell suspension cultures were established from specific parts of the formed callus. Cell suspension cultures with a high proportion of stem cells originating from roots (92–93%) or leaves (72–73%) were developed. The amount of stem cells derived from the roots in the cell suspension reached a plateau at a level of 5.60–5.72105.

Background: The Davidson Airway Function &amp; Nasal Evaluation (DAFNE) Scoring System was developed as an intuitive and research-based scoring system that could be validated through beta testing and easily introduced to healthcare providers of several subspecialties who treat nasal obstruction and breathing disorders (MDs, PAs, PTs, APRNs, DDSs, and DCs). This scoring system was shown to increase the knowledge of airway function, nasal measurement parameters, and identification of proper treatment options for sleep and breathing disorders. The basis for the DAFNE score was developed from a systematic review of nasal measurement data. Methods: Electronic searches of PubMed, MEDLINE, EMBASE Cochrane Library, and Scopus of publications between 1988-2022 were used to identify studies validating nasal function measurement parameters to create the algorithm for the DAFNE Score™. The systematic review was accomplished using the 2020 ‘Preferred Reporting Items for Systematic Reviews’ (PRISMA) guidelines. Results: Twenty studies met the inclusion criteria for systematic review. Primary outcomes measurements demonstrated reliability, repeatability and validity of the DAFNE measurement technologies, data and output. Conclusions: The data analysis and systematic review uncovered a need and framework to develop and validate a web-based software algorithm for global access to improve the understanding of data interpretation of nasal measurements from three nasal measurement technologies. DAFNE Scoring should be used as an adjunct tool in routine clinical practice and research to further understand the technology data output and how to collaborate with other healthcare providers to improve patient outcomes.

Soil organic carbon (SOC) mineralization is closely related to carbon source or sink of terrestrial ecosystem. Understanding soil organic carbon (SOC) mineralization under plum plantation is essential for improving our understanding of SOC responses to land-use change in karst rocky desertification ecosystem. In this study, 2-y, 5-y and 20-y plum plantations and adjacent woodland were sampled and a 90-day incubation experiment was conducted to investigate the effect of plum plantation with different years on SOC mineralization in subtropical China. Results showed that: (1) there was no significant difference in SOC content between different planting years, but there were significant differences in accumulative SOC mineralization (C_t) and potential SOC mineralization (C₀); (2) the dynamics of the SOC mineralization was a good fit to a first-order kinetic model. Both C₀ and C_t in calcareous soil of this study was several to ten folds lower than that in other soils, indicating that SOC in karst region has higher stability. (3) Correlation analysis revealed that both C_t and C₀ was significantly correlated with soil calcium (Ca) and C/N, indicating the important role of Ca and C/N in SOC mineralization in karst rocky desertification area.

Taking a typical forest underlying surface as the research area, this study employed the unmanned aerial vehicle (UAV) photogrammetry to explore more accurate canopy parameters including tree height and canopy radius, which were used to improve the Noah-MP land surface model conducted in Dinghushan Forest Ecosystem Research Station (CN-Din). While the canopy radius was fitted as a Burr distribution, the canopy height of CN-Din forest followed a Weibull distribution. The replacement of the parameters by these observed UAV would result in the Noah-MP model. It was found that the influence on the simulation of the energy fluxes could not be negligible, and the main influence of these canopy parameters was on the latent heat flux which could decrease up to -11% in the midday while increase up to 15% in the nighttime. Additionally, this work indicated that the description of the canopy characteristics for the land surface model should be improved to accurately deliver the heterogeneity for the underlying surface.

The solid-state welding method known as friction stir welding (FSW) bonds two metallic work parts, whether the same or different, by plastically deforming the base metal. The frictional resistance between both metallic work pieces causes them to produce heat, which produces plastic deformation and welds them. However, the weldability and strength of FSW joints mainly depend on the FSW parameters. This review work highlights the previous research work on the FSW parameters and their effects on the weldability and quality of the aluminum alloys joined with similar and dissimilar metals through the FSW method. About 150 research studies were systematically reviewed, and the articles included data from peer-reviewed journals. It has been concluded that the key parameters, including welding speed, “rotational speed”, “plunge depth”, “spindle torque”, “shoulder design”, “base material”, “pin profile” and “tool type", significantly affect the weldability of the aluminum joint through the FSW method. Also, the selection of these parameters is important and fundamental as they directly affect the joint. It is recommended that future work focus on FSW for aluminum. Among these, the most essential is the application of artificial intelligence (AI) techniques to select the optimum FSW parameters for aluminum welding.

Abstract: This study was aimed to determine the influence of the volume fraction of steel fibers and on fracture parameters of concrete. Fifty notched steel fiber reinforced concrete (SFRC) beams and ordinary concrete beams with dimensions of 100mm×100mm×515mm were cast and tested via three-point bending test. Among them, the type of steel fiber is milling type (MF), and the volume fraction of steel fiber added is 0%, 0.5%, 0.5%, 1.5%, 1.5%, 2%, respectively. The effects of the steel fiber volume fraction (VF) on the critical stress intensity factor (KIC), fracture energy (GF), the deflection at failure(δ0), the critical crack mouth opening displacement (CMODC) and the critical crack tip opening displacement (CTODC)were studied. Through the analysis of test phenomena and test data such as load-deflection (P-δ) curve, load-crack mouth opening displacement (P-CMOD) curve and load-crack tip opening displacement (P-CTOD) curve following conclusions are drawn: With the increase of steel fiber volume fraction, some fracture parameters increase gradually and maintain a certain linear growth. The gain ratio of fracture parameters increases significantly, and the gain effect is obvious. Through this law of growth, the experimental statistical formulas of fracture energy and critical stress intensity factor are summarized.

The present study uses the 3 years of data from a vertically pointed profile Radar (VPPR) at the mountain site (Huancayo at 3.2 km msl; HYO) in Peru to investigate the precipitation characteristics/patterns including diurnal variation, bright band (BB) characteristics and vertical structure of rain (VSR). VPPR provides continuous 1­min profiles of radar reflectivity (Ze), rain rate (RR), liquid water content (LWC) and Doppler velocity. At the same time, field campaign data are used to investigate the role of the surface and atmospheric variables in generating the rainfall and organization of the cloud systems over HYO. The precipitation shows the bimodal distribution; frequent and higher RR during afternoon and nighttime. The BB height also shows a diurnal pattern and BB height is higher during the afternoon and nighttime compared; and follows the diurnal heating of the Andes. More than 70% BB height lies between ~4.3­4.7 km and only 20% BB has altitude higher than 5 km. The austral summer monsoon (December to March months) have higher intense vertical profiles (higher Z e ) compared to pre monsoon seasons (September to November) and shows the nega­tive gradient for most of the altitude. The RR and LWC show the opposite characteristics, and both have a positive gradient below the 6 km altitude and then negative gradient above 6 km altitude. The raindrop size distribution (DSD) parameters show most of the variation below the freezing level, and a higher concentra­tion of large sized of hydrometeors are observed for higher RR, however the dominant modes of Dm are less than 1 mm. The changes in the VSR in DSD parameters are significant for the RR>20 mm/h, whereas for RR<2 mm/h the vertical structure in DSD parameters do not have much differences during monsoon and premonsoon seasons. Satellite and reanalysis data reveal the short periods of convective activity with higher ac­ cumulated rainfall over HYO compared to stratiform precipitation, which is more common in the nighttime and sustain for many hours. Wet spells (higher rainy days) have low pressure circulation, which favours the transport of moisture from the Amazon to the central Sierra of Peru, while the anticyclonic circulation at high levels favours the divergence at higher pressure levels and, enhances the convective in the region. During the dry spells, low level weaker circulation at the west of Brazil, restricts the transport of moisture to the central Sierra, while the circulation at high levels does not favor rain processes. The improved understanding of the tropical Andes precipitation would be very important for assessing climate variability and changes as well as to forecast precipitation using the numerical models.

A very strong earthquake of magnitude Mw8.2 struck the coastal zone of Alaska (USA), on July 29, 2021. This earthquake was felt around the Gulf of Alaska, on a wide offshore area belonging to USA and Canada. In order to identify an anomalous geomagnetic signal before the onset of this earthquake, we retrospectively analyzed the data collected on the interval June 17 - July 31, 2021, via internet (www.intermagnet.org), at the two geomagnetic observatories, College (CMO) - Alaska and Newport (NEW)-USA, by using the polarization parameter (BPOL) and the strain effect–related to geomagnetic signal identification. Thus, for the both observation sites (CMO and NEW), the daily mean distribution of the BPOL and its standard deviation (STDEV) are carried out using an FFT band-pass filtering in the ULF range (0.001-0.0083Hz). Further on, a statistical analysis based on a standardized random variable equation was applied to emphasize the following: a) the anomalous signature related to Mw8.2 earthquake on the both time series BPOL*(CMO) and BPOL*(NEW); b) the differentiation of the transient local anomalies associated with Mw8.2 earthquake from the internal and external parts of the geomagnetic field, taking the NEW observatory as reference. Finally, on the BPOL*(NEW-CMO) time series, carried out on the interval 07-31 July, 2021, a very clear anomaly of maximum, greater than 1.2 STDEV, was detected on July 22, with 7 days before the onset of Mw8.2 earthquake

Electric streamer discharges (streamers) in air are a very important stage of lightning, taking place before formation of the leader discharge, and with which an electric discharge starts from conducting objects which enhance the background elecric field, such as airplanes. Despite years of research, it is still not well understood what mechanism determines the values of streamer parameters, such as its radius and propagation velocity. The Streamer Parameter Model (SPM) is aimed to understand this mechanism, as well as to provide a way to efficiently calculate streamer parameters. Previously, we demonstrated that SPM results compared well with a limited set of experimental data. In this Brief Report, we compare SPM predictions to the published hydrodynamic simulation (HDS) results.

Estimating the parameters of statistical distributions generally involves solving a system of nonlinear equations or a nonlinear equation, being a technical difficulty in their usual application in hydrology. This article presents improved approximations and, in some cases, new approximations for the estimation with the method of ordinary moments and the method of linear moments, which are useful for the direct calculation of the parameters, because the errors in the approximate estimation are similar to the use of iterative numerical methods. Thirteen statistical distributions of two and three parameters frequently used in hydrology are presented, for which parameter estimation was laborious. Thus, the approximate estimation of the parameters by the two methods is simple but also precise and easily applicable by hydrology researchers. The approximate forms characterized by very small errors are the result of the research conducted within the Faculty of Hydrotechnics to update the romanian normative standards in the hydrotechnical field.