Rapid search and localization for nuclear sources can be an important aspect in preventing human harm from illicit material in dirty bombs or from contamination. In the case of a single mobile radiation detector, there are numerous challenges to overcome such as weak source intensity, multiple sources, background radiation, and the presence of obstructions, i.e., a non-convex environment. In this work, we investigate the sequential decision making capability of deep reinforcement learning in the nuclear source search context. A novel neural network architecture (RAD-A2C) based on the actor critic (A2C) framework and a particle filter gated recurrent unit for localization is proposed. Performance is studied in a randomized 20 x 20 m convex and non-convex environment across a range of signal-to-noise ratio (SNR)s for a single detector and single source. RAD-A2C performance is compared to both an information-driven controller that uses a bootstrap particle filter and to a gradient search (GS) algorithm. We find that the RAD-A2C has comparable performance to the information-driven controller across SNR in a convex environment and at lower computational complexity per action. The RAD-A2C far outperforms the GS algorithm in the non-convex environment with greater than 95% median completion rate for up to seven obstructions.

This paper describes a novel concept of producing energy efficient ”Maroon enriched natural gas “ and then Pink hydrogen” from any hydrocarbon base. The key idea is the extraction of hydrogen from water in addition to that from the hydrocarbon in an optimal fashion. This has the benefit of higher water vapor to CO2 exhaust ratio than conventional carbonaceous fuels when generating energy via combustion, a prudent step in achieving Netzero goals in a shorter time, and creating energy independence in most places.. The process of production makes concentrated CO₂ available for use and or sequestration. The process also maximizes use of renewable electricity in hydrogen generation, and maximizes use of existing infrastructure, with a minimum capital cost by energy recycle in the process. The process design applies sound thermodynamic principles which evolved during the nineteenth century, and mimics the geochemical processes going on in some of the natural 'colorless hydrogen'.

Large-scale crowd phenomena are complex to model because the behaviour of pedestrians needs to be described at both strategic, tactical, and operational levels and is impacted by the density of the crowd. Microscopic models manage to mimic the dynamics at low densities, whereas mesoscopic models achieve better performances in dense situations. This paper proposes and evaluates a novel agent-based architecture to enable agents to dynamically change their operational model based on local density. The ability to combine microscopic and mesoscopic models for multi-scale simulation is studied through a use case of pedestrians at the Festival of Lights, Lyon, France. Pedestrian outflow data is extracted from video recordings of exiting crowds at the festival. The hybrid model is calibrated and validated using a genetic algorithm that optimizes the match between simulated and observed outflow data. Additionally, a local sensitivity analysis is then conducted to identify the most sensitive parameters in the model. Finally, the performance of the hybrid model is compared to different models in terms of density map and computation time. The results demonstrate that the hybrid model has the capacity to effectively simulate pedestrians across varied density scenarios while optimizing computational performance compared to other models.

One of the most important applications in the wireless sensor networks (WSN) is to classify mobile targets in the monitoring area. In this paper, a multi-DBN weighted voting classification algorithm is proposed on the basis of the Deep Belief Network (DBN) classifier and combined with the idea of voting method, which is implemented on the nodes of the WSN monitoring system by means of "upper training, lower transplantation" appraoch. The performance of the algorithm is verified by using real-world experimental data, and the results show that the proposed method has a higher accuracy in classifying the target signal features, achieving an average classification accuracy of 84.63% across four different types of moving targets. The experiment reveals that the multi-DBN weighted voting algorithm enhances the target classification accuracy by approximately 5% in comparison to the single DBN classifier, but the memory and computation time required for the algorithm to run are also increased at the same time. Compared to the FFNN classifier, which exhibited the highest classification accuracy among the four selected methods, the algorithm achieves an improvement of approximately 8.8% in classification accuracy. However, it incurs greater time overhead to run.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

Rapid assessment of maize yields in smallholder farming system is important to understand its spatial and temporal variability and for timely agronomic decision-support. Imageries acquired with unmanned air vehicles (UAV) offer opportunity to assess agronomic variables at field scale, however, it is not clear if this can be translated into reliable yield assessment on smallholder farms where field conditions, maize genotypes, and management practices vary within short distances. In this study, we assessed the predictability of maize grain yield using UAV-derived vegetation indices (VI), with(out) biophysical variables, in smallholder farms. High-resolution images were acquired with UAV-borne multispectral sensor at 4 and 8 weeks after sowing (WAS) on 31 farmers’ managed fields (FMFs) and 12 nearby Nutrient Omission Trials (NOT), all distributed across 5 locations within the core maize region of Nigeria. The NOTs included non-fertilized and fertilized plots (with and without micronutrients), sown with open-pollinated or hybrid maize genotypes. Acquired multispectral images were post-processed into several three (s) vegetation indices (VIs), normalized difference vegetation index (NDVI), normalized difference red-edge (NDRE), green-normalized difference vegetation index (GNDVI). Biophysical variables, plant height (Ht) and percent canopy cover (CC), were measured with the georeferenced plot locations recorded. In the NOTs, the nutrient status, not genotype, influenced the grain yield variability and outcome. The maximum grain yield observed in NOTs was 9.3 tha^-1, compared to 5.4 tha^-1 in FMF. Without accounting for between- and within-field variations, there was no relationship between UAV-derived VIs and grain yield at 4WAS (r<0.02, P>0.1), but significant correlations were observed at 8WAS (r≤0.3; p<0.001). Ht was positively correlated with grain yield at 4WAS (r=0.5, R²=0.25, p<0.001), and more strongly at 8WAS (r=0.7, R²=0.55, p<0.001), while relationship between CC and yield was only significant at 8WAS. By accounting for within- and between-field variations in NOTs and FMF (separately) through linear mixed-effects modeling, predictability of grain yield from UAV-derived VIs was generally (R²≤0.24), however, the inclusion of ground-measured biophysical variable (mainly Ht) improved the explained yield variability (R² ≥0.62, RMSEP≤0.35) in NOTs but not in FMF. We conclude that yield prediction with UAV-acquired imageries (before harvest) is more reliable under controlled experimental conditions (NOTs), than in actual farmer-managed fields where various confounding agronomic factors can amplify noise-signal within the vegetation canopy.

This study investigates the impact of climate change on the efficiency of organic honey production in Türkiye using a machine learning approach. The eXtreme Gradient Boosting (XGBoost) algorithm is employed for the Machine Learning (ML) modelling. The analysis includes data on organic honey production performance from 2004 to 2023, spanning a period of 20 years, and 8 different climate variables (16 variables depending on daytime and nighttime values). The dataset created to investigate the impact of climate change on organic honey yield comprises 28 columns and 120,960 rows. The study aimed to determine the significance of different climatic variables on the efficiency of organic honey production. The study found that, in addition to daytime solar radiation and temperature, wind speed and direction were also important factors. The sensitivity analysis has shown that minor alterations in the variables have a significant impact on the model's predictions. Additionally, non-linear relationships between the variables and honey production were identified. These findings suggest that it may be beneficial to consider implementing climate change adaptation and mitigation strategies in agricultural policies and beekeeping practices. The study suggests that machine learning has the potential to provide valuable insights into the complex relationship between climate change and agricultural production. This could aid in the sustainability and economic optimization of the sector.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

Commonly, professors, students and researchers from universities around the world use software distributed under a license agreement for computer simulation purposes, which requires a computer with considerable hardware capabilities. Consequently, this implies a high cost to conduct simulations that require implementing numerical methods in all areas of engineering, particularly in the field of robotics and nonlinear control. This paper presents the design and results analysis of a low-cost and open-source frugal computer simulation tool with applications to robotic nonlinear control, for instance, for numerical simulations of manipulator robot control based on dynamic models. Using a single board minicomputer with with reduced computing power, Raspberry Pi, together with free software, GNU-Octave, trajectory tracking control simulations in the joint space of a Selective Conformal Assembly Robot Arm (SCARA) are achieved by solving a system of nonlinear differential equations, represented in matrix form, which includes the control law and the system model. The results of the proposed alternative are compared by running the same simulation code on a laptop computer using MATLAB and GNU Octave, which show minimal deviations and reasonable time complexity. Moreover, considering the frugality curve calculated for this approach, in addition to the low acquisition cost of the simulation software tool, it would allow the creation of a simulation laboratory in some universities with budgetary constraints for educational and research purposes.

River monitoring has the potential to grow substantially with present-day available affordable and locally sourced hardware. Yet river monitoring networks are still under pressure due to lack of resources, difficulties with maintenance, and rapidly changing conditions which in part may be due to climate change. We advocate that to turn around this trend, monitoring stations must rely on local people, work with locally available devices, work without contact with water and operate through openly available knowledge. River observations with camera videos have this potential. IP cameras, drones or smartphones are widely available as observation platforms. The scientific methods are well established in literature. Yet current attempts to establish scalable open-source software solutions that can be operated anywhere are lacking. In fact, currently available software is either research-oriented, more aimed at incidental observations, is restricted to single-use licenses, entirely proprietary, or restricted to operations through a third-party Software as a Service. To overcome this obstacle, we present OpenRiverCam, a free and open-source software ecosystem for river observations that can fulfill a wide variety of use cases and business cases through a well-documented and simple to use Application Programming Interface, service workflows, cloud scalability and interoperability, and options to extend to several applications within the hydrological, hydrodynamic, environmental and geospatial domains. We demonstrate its current technical abilities through three different case studies that all originate from a user perspective. We discuss the future developments to meet further requirements, which include documentation, widely available training materials and embedding in curricula, and further hardware and software developments.

This paper discusses a means of making an extremely bright path entangled source. An initial laser source is preferred but any source of light: LED, sub-critical laser, coherent or thermal can be used. The light is dimmed by a beam expander until the relative number of |1> or |2> photons increases compared to higher photon states. The expanded beam is then passed through a 1:1 beamsplitter to generate path entanglement on the |1> and |2> photons. A further stage of “purification” can remove the non-entangled higher states by passing the output beams from the beamsplitter through one another, such that the correlated entangled photon electrical fields cancel in some region. In the said region, the uncorrelated non-entangled fields can be Faraday rotated and then absorbed by a polariser. The entangled photons pass through the region without rotation and attenuation. The output from the device then has copious quantities of 1 and 2 photon path entangled suitable for use in telecommunications engineering, secure transmission of data and quantum metrology. The wide beams can be beam-contracted to a thin bright beam and will keep the path entanglement of individual photons, as photons are bosons and so don’t interact, furthermore, all operations are unitary and linear, as by Maxwell’s equations.

In order to better understand the source-sink flow and relationships of Zinc (Zn) and other nutrients in wheat (Triticum aestivum L.) plants for biofortification and improving grain nutritional quality, effects of reducing photoassimilate source (through the flag leaf removal and spike shading) or sink (through 50% spikelets removal) in the field on accumulation of Zn and other nutrients in wheat grains of two cultivars (Jimai 22 and Jimai 44) were investigated under two soil Zn application levels. The single panicle weight (SPW), kernel number per spike (KNPS), thousand kernel weight (TKW), total grain weight (TGW), concentrations and yields of various nutrient elements (Zn, Fe, Mn, Cu, N, P, K, Ca and Mg), phytate phosphorus (phytate-P), phytic acid (PA) and phytohormones (ABA: abscisic acid, and the ethylene precursor ACC: 1-aminocylopropane-1-carboxylic acid), and C/N ratios were determined. Soil Zn application significantly increased concentrations of grain Zn, N and K. Cultivars showing higher grain yields had lower grain protein and micronutrient nutritional quality. SPW, KNPS, TKW (with an exception of TKW in half spikelets removal), TGW, and nutrient yields in wheat grains were most severely reduced by half spiklets removal, secondly by spike shading, and slightly by flag leaf removal. Grain concentrations of Zn, N and Mg consistently showed negative correlations with SPW, KNPS and TGW, but positively with TKW. There were general positive correlations among grain concentrations of Zn, Fe, Mn, Cu, N and Mg, and bioavailability of Zn and Fe (estimated by molar ratios of PA/Zn, PA × Ca/Zn, PA/Fe, or PA × Ca/Fe). Although concentrations of Zn and Fe were increased and Ca was decreased in treatments of half spikelets removal and spike shading, the simultaneously increased PA limited the increase in bioavailability of Zn and Fe. In general, different nutrient elements interact with each other and are affected to different degrees by source-sink manipulations. Elevated endogenous ABA levels and ABA/ACC ratios were associated with increased TKW and grain-filling of Zn, Mn, Ca and Mg, and inhibited K in wheat grains. However, effects of ACC were diametrically opposite. These results provide basis for wheat grain biofortification to alleviate human malnutrition.

Characterization of flying insects in-situ measurement using remote sensing spectroscopy is an emerging research field. Also, most analysis techniques in remote sensing spectroscopy are based on the use of an intensity threshold which introduces indeterminacies in the number of detected specimens. In this manuscript, we investigated the possibility of analysing passive remote sensing spectroscopy measurement data using the maximum noise fraction method. The results obtained show that this analysis technique can help to overcome the measurement of background noise in spectroscopic measurements.

Three-dimensional (3D) bioprinting promises to be essential in tissue engineering for solving the rising demand for organs and tissues. Some bioprinters are commercially available, but their impact on the field of TE is still limited due to their cost or difficulty to tune. Herein, we present a low-cost easy-to-build printhead for microextrusion-based bioprinting (MEBB) that can be installed in many desktop 3D printers to transform them into 3D bioprinters. We can extrude bioinks with precise control of print temperature between 2 - 60 ºC. We validated the versatility of the printhead, by assembling it in three low-cost open-source desktop 3D printers. Multiple units of the printhead can also be easily put together in a single printer carriage for building a multi-material 3D bioprinter. Print resolution was evaluated by creating representative calibration models at different temperatures using natural hydrogels such as gelatin and alginate, and synthetic ones like poloxamer. Using one of the three modified low-cost 3D printers, we successfully printed cell-laden lattice constructs with cell viabilities higher than 90% after 24h post printing. Controlling temperature and pressure according to the rheological properties of the bioinks was essential in achieving optimal printability and great cell viability. The cost per unit of our device, which can be used with syringes of different volume, is less expensive than any other commercially available product. These data demonstrate an affordable open-source printhead with the potential to become a reliable alternative to commercial bioprinters for any laboratory.

The utility of ICTs for providing market information to rural smallholder farmers is growing rapidly, and access to reliable information and sources is considered crucial for beneficial market interaction. This study explored critical factors contributing to usage of electronic sources for market information search among rural smallholder livestock farmers. Using data collected from 129 respondents through a non-random sampling technique; descriptive and regression analysis was applied to identify key factors responsible for their awareness and use of ICT-based market information sources. Level of education was found to be a driver of awareness of ICT-based sources, and use of these sources was influenced by farmer-specific characteristics such as household size, education, income, membership of cooperatives and herd-size. The key ICT tools used was radio and mobile phones, widely available in the study area. Identified constraints to use of these ICTs include cost and patchy network signals in some areas. Policy interventions to reduce cost of mobile phone services and expansion of base stations; including practical recommendations for improved programming in radio and television offerings, are considered indispensable for greater uptake of e-information sources among smallholder livestock farmers.

This research work deals with the modeling and control of hybrid photovoltaic (PV) - Wind micro-grid using Quasi Z-Source inverter. This inverter provides better buck/boost characteristics, able to regulate the phase angle output, less harmonic content, no requirement of the filter and has high power performance characteristics over conventional inverter as major benefits. A SEPIC converter as dc-dc switched power apparatus is employed for maximum power point tracking (MPPT) functions which provides high voltage gain throughout the process. Moreover, a modified power ratio variable step (MPRVS) based perturb & observe (P&O) method has been proposed in the PV MPPT action which forces the operating point close to maximum power point (MPP). Practical responses justify the performance of hybrid PV-Wind micro-grid with Quasi Z-Source inverter structure.

Ozone and fine particles (PM_2.5) are the two main air pollutants of concern in the New South Wales Greater Metropolitan Region (NSW GMR) region due to their contribution to poor air quality days in the region. This paper focuses on source contributions to ambient ozone concentrations for different parts of the NSW GMR, based on source emissions across the greater Sydney region. The observation-based Integrated Empirical Rate Model (IER) was applied to delineate the different regions within the GMR based on the photochemical smog profile of each region. Ozone source contribution is then modelled using the CCAM-CTM (Cubic Conformal Atmospheric Model-Chemical Transport Model) modelling system and the latest air emission inventory for the greater Sydney region. Source contributions to ozone varied between regions, and also varied depending on the air quality metric applied (e.g., average or maximum ozone). Biogenic volatile organic compound (VOC) emissions were found to contribute significantly to median and maximum ozone concentration in North West Sydney during summer. After commercial domestic, power station was found to be the next largest anthropogenic source of maximum ozone concentrations in North West Sydney. However, in South West Sydney, beside commercial and domestic sources, on-road vehicles were predicted to be the most significant contributor to maximum ozone levels, followed by biogenic sources and power stations. The results provide information which policy makers can devise various options to control ozone levels in different parts of the NSW Greater Metropolitan Region.

Urgent environmental challenges and emerging additive manufacturing (AM) technologies push research towards more performant and new materials. In the field of metallurgy, high entropy alloys (HEAs) have recently represented a topic of intense research because of their promising properties, such as high temperature strength and stability. Moreover, this class of multi-principal element alloys (MPEAs) have opened up researcher community to unexplored compositional spaces, making prosper literature of high-throughput methodologies and tools for rapidly screening large number of alloys. However, none of the methods has been aimed to design new MPEAs for AM process known as selective laser melting (SLM) so far. Here we conducted nanoindentation testing on single scan tracks of elemental powder blends and pre-alloyed powders after ball milling of AlTiCuNb and AlTiVNb. Results show that nanoindentation can represent an effective technique to gain information about phase evolution during laser scanning, contributing to accelerate the development of new MPEAs.

Smart Internet of Vehicles (IoVs) combined with Artificial Intelligence (AI) will contribute to vehicle decision-making in the Intelligent Transportation System (ITS). Multi-Vehicle Pursuit games (MVP), a multi-vehicle cooperative ability to capture mobile targets, is becoming a hot research topic gradually. Although there are some achievements in the field of MVP in the open space environment, the urban area brings complicated road structures and restricted moving spaces as challenges to the resolution of MVP games. We define an Observation-constrained MVP (OMVP) problem in this paper and propose a Transformer-based Time and Team Reinforcement Learning scheme (T3OMVP) to address the problem. First, a new multi-vehicle pursuit model is constructed based on decentralized partially observed Markov decision processes (Dec-POMDP) to instantiate this problem. Second, by introducing and modifying the transformer-based observation sequence, QMIX is redefined to adapt to the complicated road structure, restricted moving spaces and constrained observations, so as to control vehicles to pursue the target combining the vehicle’s observations. Third, a multi-intersection urban environment is built to verify the proposed scheme. Extensive experimental results demonstrate that the proposed T3OMVP scheme achieves significant improvements relative to state-of-the-art QMIX approaches by 9.66%~106.25%. Code is available at https://github.com/pipihaiziguai/T3OMVP.

Abstract: Thermal desalination is yet a reliable technology in the treatment of brackish water and seawater; however, its demanding high energy requirements have lagged it compared to other non-thermal technologies such as reverse osmosis. This review provides an outline of the development and trends of the three most commercially used thermal or phase change technologies worldwide: Multi Effect Distillation (MED), Multi Stage Flash (MSF), and Vapor Compression Distillation (VCD). First, state of water stress suffered by regions with little fresh water availability and existing desalination technologies that could become an alternative solution are shown. The most recent studies published for each commercial thermal technology are presented, focusing on optimizing the desalination process, improving efficiencies, and reducing energy demands. Then, an overview of the use of renewable energy and its potential for integration into both commercial and non-commercial desalination systems is shown. Finally, research trends and their orientation towards hybridization of technologies and use of renewable energies as a relevant alternative to the current problems of brackish water desalination are discussed. This reflective and updated review will help researchers to have a detailed state of the art of the subject and to have a starting point for their research, since current advances and trends on thermal desalination are shown.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

A millimeter-wave (mmWave) gallium nitride (GaN) high-power amplifier (PA) monolithic microwave-integrated circuit (MMIC) was implemented, considering a source via effect. In this paper, we introduce guidelines for designing GaN high PA MMICs, from device sizing to meeting high-power specifications, power matching considering source via effects, schematic design of three-stage amplifier structures, and electromagnetic (EM) simulation. Based on the results of load pull simulation and small-signal maximum stable gain (MSG) simulation, the GaN high electron-mobility transistor (HEMT) size was selected to be 8×70 μm. However, since the source via model provided by the foundry was significantly different from the EM results, it was necessary to readjust the power matching considering this. Additionally, when selecting the source via size, the larger the size, the easier the matching, but since the layout of the peripheral bias circuit is not possible, a compromise was required considering the actual layout. To prevent in-band oscillation, an RC parallel circuit was added to the input matching circuit, and low-frequency oscillation was solved by adding a gate resistor on the PCB module. The proposed PA was fabricated with a commercial 0.1 μm GaN HEMT MMIC process. It exhibited 38.56 to 39.71 dBm output power (Pout), 14.2 to 16.7 dB linear gain, and 14.1% to 18.2% power-added efficiency (PAE) between 34 and 36 GHz. The fabricated GaN power amplifier MMIC shows competitive Pout in the Ka upper band above 33 GHz

The NP method was used to elucidate the contributions of vehicles and coal combustion to seasonal and long-term atmospheric PM-bound Pyr and 1-NP concentrations in Kanazawa, Kitakyushu, Shenyang, and Shanghai in the Western Pacific region from 1997 to 2021. Among the four cities, Kanazawa demonstrated the lowest Pyr concentration. The contribution of vehicles to Pyr before and after 2010 were 35% and 5%, respectively. The 1-NP concentration reduced by a factor of more than 1/10. These changes can be attributed to the emission control from vehicles. Kitakyushu revealed the second lowest Pyr and the lowest 1-NP concentrations. Coal combustion was found to be the main contributor to Pyr, while its contribution to 1-NP increased from 9% to 19%. The large contribution of coal combustion is attributed to iron manufactures. Shenyang demonstrated the highest atmospheric Pyr concentration with its largest seasonal change. Vehicles are the largest contributors to 1-NP. However, coal combustion, including winter coal heating, contributed 97% or more to Pyr and more than 14% to 1-NP. Shanghai revealed the second highest Pyr and 1-NP concentrations, but the former was substantially lower than in Shenyang. Coal combustion was the major contributor, but the contribution of vehicles to Pyr was larger before 2010 similar to Kanazawa.

The objective of the present study was to develop and optimize an efficient growth media for Lactobacillus delbrueckii ssp. bulgaricus, an essential dairy starter culture, uses plant-based nitrogen sources. The composition of the de Man, Rogosa, and Sharpe (MRS) culture medium was modified, and the nitrogen content was replaced by alternative nitrogen sources X-Seed N7 and N5 in various blends of 3% and 1.5%. Results showed that bacterial growth was higher with the N7 and N5 nitrogen source blends at 3% and 1.5%. Similarly, the optical densities of the L. bulgaricus strains were higher in the N7 and N5 blends (1.5/3%) compared to the MRS medium. Although there was no significance in bacterial counts for both the MRS and the N7 and N5 media, a significant difference between the control medium and the optimized growth media was noted. Our results thus suggest that the alternative nitrogen sources X-Seed N7 and N5 can substantially support the growth of lactic acid bacteria as shown with L. bulgaricus. Moreover, the presence of complex nitrogen sources rich in free nucleotides, amino acids, and peptides enhanced L. bulgaricus growth. Our results support the development of cost-effective and plant-based growth media for LAB cultures and potential benefits to the food and dairy industries. Additional research is warranted to improve buffering capacity for higher cell counts.

Static and dynamic analysis of website security risks is generally used for website security meas-urements. The website security measurements method recently proposed includes similarity hash-based website security risk analysis and machine learning-based website security risk anal-ysis. In this study, a method that can be performed through information disclosed on the Internet was proposed to measure the risk of a website. DNS information, IP information, and website history information are required to measure the risk of a website. In addition, global traffic rank-ing, malicious code distribution history, and HTTP access status can be checked in the website history information. In this study, information related to the security risk of websites in a total of 2,000 domains was collected and analyzed in 1,000 normal and malicious domains. Through the experiment results, 11 open information collection items were selected to measure the security risk of the website. This study presented the possibility of using public information collection to measure website security risk.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

Nowadays Air-Source Heat Pumps (ASHP) in combination with a Photovoltaic (PV) installation are a very promising option for a necessary and urgent energy transformation in European Union (EU). It is extremely important to develop solutions that will help maximize the use of energy generated from renewable energy sources (RES). Such issues include the problem of insufficient use of generated electricity in PV on-grid microinstallations in residential buildings. This paper's aim is to analyze the results of one-year-round operation of a PV array grid-connected hybrid installation with ASHP for domestic hot water (DHW) preparation in a residential building in Cracow, Poland in the context of increasing self-consumption (SC) of PV energy. Models of systems are built and simulated in Transient System Simulation Tool 18 (TRNSYS) software. Simulations were carried out for different scenarios involving different building electricity consumption profiles, PV system capacity and specified runtime management of ASHP. The novelty of this study lies in the evaluation of the impact of a certain range of conditions on the energy performance of the system, in particular on SC. The results showed that the use of ASHP, with specified runtime management, results in an increase in monthly SC values from 7 to 18%, and annual SC values up to 13%. Also determining the appropriate size of the used PV system depending on whether it is present ASHP in the installation is crucial to increase the value of the SC parameter. Overall, this study provides valuable insights into the potential benefits of PV panels and ASHP operating together, in particular on SC values.

Heavy metals are toxic, persistent and non-degradable. After sedimentation and adsorption, they accumulate in water sediments. The aim of this study was to understand the heavy metal pollution of Qinjiang River sediments on the ecological environment and apportioning sources. The mean total concentrations of Mn, Zn, Cr, Cu, and Pb are 3.14, 2.33, 1.39, 5.79, and 1.33 times higher than the background values, respectively, except for the Co, Ni, and Cd, which are lower than the background values; Fe, Co, Ni, Cd, Cr, Cu, and Pb are all primarily in the residual state, while Mn and Zn are primarily in the acid-soluble and oxidizable states, respectively. Igeo, RI, SQGs and RAC together indicate that the pollution status and ecological risk of heavy metals in Qinjiang River sediments are generally moderate; among them, Fe, Co, Ni, Cd, Cr, and Pb are not harmful to the ecological environment of the Qinjiang River. Cu is not readily released because of its higher residual composition, depicting that Cu is less harmful to the ecological environment. Mn and Zn, as the primary pollution factors of the Qinjiang River, are harmful to the ecological environment. This heavy metal pollution in surface sediments of the Qinjiang River primarily comes from manganese and zinc ore mining. Manganese carbonate and its weathered secondary manganese oxide are frequently associated with a significant amount of residual copper and Cd, as a higher pH is suitable for the deposition and enrichment of these heavy metals. Lead-zinc ore and its weathering products form organic compounds with residual Fe, Co, Cr, and Ni, and their content is related to salinity. The risk assessment results of heavy metals in sediments provide an important theoretical basis for the prevention and control of heavy metal pollution in Qinjiang River.

Beach sand may act as a reservoir for numerous micro-organisms, including enteric pathogens. Several of these pathogens originate in human or animal feces, which may pose a public health risk. In August 2019, high levels of fecal indicator bacteria (FIB) were detected in the sand of the Azorean beach Prainha, Terceira Island, Portugal. Remediation measures were promptly implemented, including sand removal and the spraying of chlorine to restore the beach sand quality. To determine the biological source of the contamination, during the first campaign, supratidal sand samples were collected from several sites along the beach, followed by microbial source tracking (MST) analyses of Bacteroides markers for five animal species, including humans. Some of the sampling sites revealed the presence of marker genes from dogs, seagulls, and ruminants. Making use of the information on biological sources originating partially from dogs, the municipality enforced restrictive measures for dog-walking at the beach. Subsequent sampling campaigns detected low FIB contamination due to the mitigation and remediation measures that were undertaken, thereby no longer requiring MST marker-gene analysis. This is the first case study where the MST approach was used to determine the contamination sources in the supratidal sand of a coastal beach. Our results show that MST can be an essential approach to determine sources of fecal contamination in the sand. This study shows the importance of holistic management of beaches that should go beyond water quality monitoring for FIB, putting forth evidence for the need for sands also to be monitored.

The problem of reliable function computation is extended by imposing privacy, secrecy, and storage constraints on a remote source whose noisy measurements are observed by multiple parties. The main additions to the classic function computation problem include 1) privacy leakage to an eavesdropper is measured with respect to the remote source rather than the transmitting terminals’ observed sequences; 2) the information leakage to a fusion center with respect to the remote source is considered as a new privacy leakage metric; 3) the function computed is allowed to be a distorted version of the target function, which allows to reduce the storage rate as compared to a reliable function computation scenario in addition to reducing secrecy and privacy leakages; 4) two transmitting node observations are used to compute a function. Inner and outer bounds on the rate regions are derived for lossless and lossy single-function computation with two transmitting nodes, which recover previous results in the literature. For special cases that include invertible and partially-invertible functions, and degraded measurement channels, exact lossless and lossy rate regions are characterized, and one exact region is evaluated for an example scenario.

In the present study, the polysaccharide-hydrolyzing secretomes of Irpex lacteus BCC104, Pycnoporus coccineus BCC310, and Schizophyllum commune BCC632 were analyzed in submerged fermentation conditions to elucidate the effect of chemically and structurally different carbon sources on the expression of cellulases and xylanase. Among polymeric substrates, crystalline cellulose appeared to be the best carbon source providing the highest endoglucanase, total cellulase, and xylanase activities. Mandarin pomace as a growth substrate for S. commune allowed to achieve comparatively high volumetric activities of all target enzymes while wheat straw induced a significant secretion of cellulase and xylanase activities of I. lacteus and P. coccineus. A synergistic effect on the secretion of cellulases and xylanases by the tested fungi was observed when crystalline cellulose was combined with mandarin pomace. In I. lacteus the cellulase and xylanase production is inducible in the presence of cellulose-rich substrates but is suppressed in the presence of an excess of easily metabolizable carbon source. These enzymes are expressed in a coordinated manner under all conditions studied. It was shown that the substitution of glucose in the inoculum medium with Avicel provides accelerated enzyme production by I. lacteus and higher cellulase and xylanase activities of the fungus. These results add new knowledge to the physiology of basidiomycetes to improve cellulase production.

Background: The human mind is multimodal. Yet most behavioral studies rely on century-old measures such as task accuracy and latency. To create a better understanding of human behavior and brain functionality, we should introduce other measures and analyze behavior from various aspects. However, it is technically complex and costly to design and implement the experiments that record multiple measures. To address this issue, a platform that allows synchronizing multiple measures from human behavior is needed. Method: This paper introduces an opensource platform named OpenSync, which can be used to synchronize multiple measures in neuroscience experiments. This platform helps to automatically integrate, synchronize and record physiological measures (e.g., electroencephalogram (EEG), galvanic skin response (GSR), eye-tracking, body motion, etc.), user input response (e.g., from mouse, keyboard, joystick, etc.), and task-related information (stimulus markers). In this paper, we explain the structure and details of OpenSync, provide two case studies in PsychoPy and Unity. Comparison with existing tools: Unlike proprietary systems (e.g., iMotions), OpenSync is free and it can be used inside any opensource experiment design software (e.g., PsychoPy, OpenSesame, Unity, etc., https://pypi.org/project/OpenSync/ and https://github.com/moeinrazavi/OpenSync_Unity). Results: Our experimental results show that the OpenSync platform is able to synchronize multiple measures with microsecond resolution.

Higher order femtoscopy measured to examine the heat exchanger characterization of the fluid debris produced in the collisions and investigated a remarkable suppression in the bosons interferences measurement. The analogous suppression can be analyzed to explore the coherence of boson thermal particle production sources at unprecedented energies. We illustrate the particles emissions from radiated sources with statistical coherence which induce the thermal particles interferences to probe the peculiarity of the heated sources as well as the distinctions about the heat exchangers in the collisions at higher temperature. We perspicacious that the bosons seem to the pertinent aspirant of heat exchanger, and the normalized three particles correlators evaluate the existence of such hybrid phases significantly. The key point of this research is that we analyze the three particles correlations with their normalized correlations by difference equations to determine the characteristics of heat exchanger and its applications. With such distinctive and efficient approach, we observe a significant difference in the correlation functions at higher temperature and momenta regimes.

Machine learning applications often need large amounts of training data to perform well. Whereas unlabeled data can be easily gathered, the labeling process is difficult, time-consuming, or expensive in most applications. Active learning can help solve this problem by querying labels for those data points that will improve the performance the most. Thereby, the goal is that the learning algorithm performs sufficiently well with fewer labels. We provide a library called scikit-activeml that covers the most relevant query strategies and implements tools to work with partially labeled data. It is programmed in Python and builds on top of scikit-learn.

We present a generic and open-source framework for the numerical modeling of the expected transport and storage mechanisms in unconventional gas reservoirs. These unconventional reservoirs typically contain natural fractures at multiple scales. Considering the importance of these fractures in shale gas production, we perform a rigorous study on the accuracy of different fracture models. The framework is validated against an industrial simulator and is used to perform a history-matching study on the Barnett shale. This work presents an open-source code that leverages cutting-edge numerical modeling capabilities like automatic differentiation, stochastic fracture modeling, multi-continuum modeling and other explicit and discrete fracture models. We modified the conventional mass balance equation to account for the physical mechanisms that are unique to organic-rich source rocks. Some of these include the use of an adsorption isotherm, a dynamic permeability-correction function, and an embedded discrete fracture model (EDFM) with fracture-well connectivity. We explore the accuracy of the EDFM for modeling hydraulically-fractured shale-gas wells, which could be connected to natural fractures of finite or infinite conductivity, and could deform during production. Simulation results indicates that although the EDFM provides a computationally efficient model for describing flow in natural and hydraulic fractures, it could be inaccurate under these three conditions: 1. when the fracture conductivity is very low. 2. when the fractures are not orthogonal to the underlying Cartesian grid blocks, and 3. when sharp pressure drops occur in large grid blocks with insufficient mesh refinement. Each of these results are very significant considering that most of the fluids in these ultra-low matrix permeability reservoirs get produced through the interconnected natural fractures, which are expected to have very low fracture conductivities. We also expect sharp pressure drops near the fractures in these shale gas reservoirs, and it is very unrealistic to expect the hydraulic fractures or complex fracture networks to be orthogonal to any structured grid. In conclusion, this paper presents an open-source numerical framework to facilitate the modeling of the expected physical mechanisms in shale-gas reservoirs. The code was validated against published results and a commercial simulator. We also performed a history-matching study on a naturally-fractured Barnett shale-gas well considering adsorption, gas slippage & diffusion and fracture closure as well as proppant embedment, using the framework presented. This work provides the first open-source code that can be used to facilitate the modeling and optimization of fractured shale-gas reservoirs. To provide the numerical flexibility to accurately model stochastic natural fractures that are connected to hydraulically-fractured wells, it is built atop other related open-source codes. We also present the first rigorous study on the accuracy of using EDFM to model both hydraulic fractures and natural fractures that may or may not be interconnected.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

Despite increased awareness of and attention to the need for sustainable agriculture, fertilizers and compost application in excess of crop requirements remain common agricultural practices in South Korea, causing eutrophication of freshwater and coastal ecosystems. In this study, a phosphorus (P) budget was developed to quantify P inputs, outputs, and retention in a forested- agricultural watershed. The P budget showed that chemical fertilizers and organic compost were the largest source of P (97.6% of the total) followed by atmospheric deposition (2.1% of the total P), whereas forest export (0.2% of the total) and sewage treatment plants (STPs) (0.1% of the total) were negligible. The dominant P outputs were crop harvesting and hydrologic export to surface water. The P balance showed a significant accumulation of P in the watershed; approximately 87% of the total P input was retained in the soils within the watershed. However, P concentrations in drainage water were still high enough to cause eutrophication of downstream reservoirs. The results provide useful information on the proportion of P export and retention in soils and will help support efforts to improve water quality and design better management of agricultural non-point source pollution.

This paper presents a novel approach for indoor acoustic source localization using microphone arrays and based on a Convolutional Neural Network (CNN). The proposed solution is, to the best of our knowledge, the first published work in which the CNN is designed to directly estimate the three dimensional position of an acoustic source, using the raw audio signal as the input information avoiding the use of hand crafted audio features. Given the limited amount of available localization data, we propose in this paper a training strategy based on two steps. We first train our network using semi-synthetic data, generated from close talk speech recordings, and where we simulate the time delays and distortion suffered in the signal that propagates from the source to the array of microphones. We then fine tune this network using a small amount of real data. Our experimental results show that this strategy is able to produce networks that significantly improve existing localization methods based on SRP-PHAT strategies. In addition, our experiments show that our CNN method exhibits better resistance against varying gender of the speaker and different window sizes compared with the other methods.

The Agricultural Policy/Environmental eXtender (APEX) model is widely used for evaluating agricultural conservation efforts and their effects on soil and water. A key component of APEX application in Korea is simulating water quality impacts of rice paddies because rice agriculture claims the largest cropland area in the country. In this study, a computational module called APEX-Paddy is developed to simulate water quality with considering pertinent paddy management practices such as puddling, flood irrigation management. Data collected at two experimental paddy sites in Korea were used to calibrate and validate the model. Results indicate that APEX-Paddy performs well in predicting runoff discharge rate and nitrogen yield while the original APEX highly overestimates runoff rates and nitrogen yields on large storm events. With APEX-Paddy, simulated and observed flow and mineral nitrogen yield (QN) are found to be highly correlated after calibration (Nash & Sutcliffe Efficiency (NSE) = 0.87 and Percent Bias (PBIAS) = −14.6% for flow; NSE = 0.68 and PBIAS = 2.1% for QN). Consequently, the APEX-Paddy showed a greater accuracy in flow and QN prediction than the original APEX modeling practice using the SCS-CN method.

Given a stream of depth images with a known cuboid reference object present in the scene, we propose a novel approach for accurate camera tracking and volumetric surface reconstruction in real-time. Our contribution in this paper is threefold: (a) utilizing a priori knowledge of the cuboid reference object, we keep drift-free camera tracking without explicit global optimization; (b) we improve the fineness of the volumetric surface representation by proposing a prediction-corrected data fusion strategy rather than simple moving average, which enables accurate reconstruction of high-frequency details such as sharp edges of objects and geometries of high curvature; (c) we introduce a benchmark dataset CU3D containing both synthetic and real-world scanning sequences with ground-truth camera trajectories and surface models for quantitative evaluation of 3D reconstruction algorithms. We test our algorithm on our dataset and demonstrate its accuracy compared with other state-of-the-art algorithms. We release both our dataset and code as opensource1 for other researchers to reproduce and verify our results.

In this paper, the methods and their analysis for estimating the location of three dimension (3-D) single source buried in lossy medium are presented with uniform circular array (UCA). The mathematical model of the signal in the lossy medium is proposed. Using location information in the covariance matrix obtained by sensors’ output, the equations of the source location (azimuth angle, elevation angle and range) are obtained. The phase and amplitude of the covariance matrix function are used to process these equations respectively. Then, the phase and amplitude of the covariance matrix function are used to process the source localization in the conductive medium together. By analyzing the characteristics of the proposed methods and MUSIC method, the computational complexity and the valid range of these methods are given. From the results, whether the loss is known, we can choose the appropriate method to process the issues (localization in lossless medium or lossy medium).

Societies around the world face serious energy problems related to the consumption of fossil fuels and the emission of dangerous radiation. To solve these problems, a new superconductor exhibiting a critical temperature higher than room temperature has been pursued but not achieved. This paper proposes a new energy generation system based on a circuit approach. Secondary to this process, a new type of superconductivity without refrigeration is demonstrated. In our previous paper [1], this system was proposed, but it did not describe the underlying theory in detail and did not mention an actual method to generate energy from the system. The present paper describes the theory of the existence of divergent current density and new superconductivity with no refrigeration. Moreover, the present paper proposes a method for extracting energy from the system by employing a voltage-controlled current source (i.e., a voltage–current converting method).The principle of the system is based on a circuit of two loops and independent current sources. First, the two electric loops are prepared, each with 4 diodes, where the diodes are oriented in the same direction within each loop, but their direction is opposite from loop to loop; four independent current sources connect the loops. In this circuit system, current is added iteratively as it flows along the loop according to Kirchhoff’s circuit law. As a result, a large current and electric potential are present along the loop. To confirm that this system works properly, it is necessary to demonstrate the presence of divergent currents in the transient state, and to do this, the present paper employs the Dirac equation and Lorentz conservation. Electric circuit software is employed to demonstrate that the presented method generates energy actually from our system.Our results confirm the presence of divergent current at a connected point of an independent current source in the transient state. Moreover, in the steady state, the theory demonstrates the Meissner effect (i.e., a London equation) and a new type of macroscopic wave function and condensation. For an initial small input current of 0.1 μA, the simulation reveals a large generating current of 7 kA and electric power of 10¹¹ W, which is much larger than unit of power from an average thermal power station; moreover, the system presents with superconducting electrical transport conditions.The present study is significant because it demonstrates theoretically the existence of divergent current density and a new type of superconductivity requiring no refrigeration. Secondly, the simulations show the generation of a large energy density that can be obtained in a small laboratory room with minimal cost.

Real-world optimization problems are often governed by one or more constraints. Over the last few decades, extensive research has been performed in Constrained Optimization Problems (COPs) fueled by advances in computational intelligence. In particular, Evolutionary Algorithms (EAs) are a preferred tool for practitioners for solving these COPs within practicable time limits. We propose an ensemble of multi- method hybrid EA framework with four mutation operators, two crossover operators, multi-search [Differential Evolution (DE) & Gaining Sharing Knowledge (GSK)] optimization algorithm, and ensemble of constraint handling techniques to solve global real- world constrained optimization problem. The proposed frame- work FEPEA has an ascendancy of multiple adaptation strategies concerning the control parameters, search mechanisms, two sub-populations as well as uses knowledge sharing mechanism between junior and senior phases. The algorithm also combines the power of four popular constraint handling techniques (CHT) and uses a voting mechanism to select any particular CHT. On top of that, this algorithm also uses both linear and non- linear population size reduction in every step of the evolutionary process. We test our method on 57 real-world problems provided as part of the CEC 2020 special session & competition on real- world constrained optimization benchmark suite. Experimental results indicate that FEPEA is able to achieve state-of-the- art performance on real-world constrained global optimization when compared against other well-known real-world constrained optimizers.

The hybrid bond graph has been studied in depth for scalar bond graphs, but how does this translate to the multi-bond graph? Here, the controlled junction – used to model structural switching such as contact – is extended to the multi-bond case. This is a simple process, assuming that all bonds switch simultaneously (which makes physical sense). A controlled 0-junction is applied to multi-bond graph of a car, which can lose contact with the ground in cornering. Dynamic causality features, but this can be accommodated using an equational submodel in 20-Sim (in a manner similar to that used with scalar bond graphs). The junction is proposed for subsequent work to develop a validated multi-body dynamics car model in cornering.

The framework of product life cycle (PLC) cost analysis is one of the most important evaluation tools for a contemporary high-tech company in an increasingly competitive market environment. The PLC-purchasing strategy provides the framework for a procurement plan and examines the sourcing strategy of a firm. The marketing literature emphasizes that ongoing technological change and shortened life cycles are important elements in commercial organizations. From a strategic viewpoint, the vendor has an important position between supplier, buyer and manufacturer. The buyer seeks to procure the products from a set of vendors to take advantage of economies of scale and to exploit opportunities for strategic relationships. However, previous studies have seldom considered vendor selection (VS) based on PLC cost (VSPLCC) analysis. The purpose of this paper is to solve the VSPLCC problems considering the situation of a single-buyer-multiple-supplier. For this issue, a new VSPLCC procurement model and solution procedure are derived by this paper to minimize net cost, rejection rate, late delivery and PLC cost subject to vendor capacities and budget constraints. Moreover, a real case in Taiwan is provided to show how to solve the VSPLCC procurement problem.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

This paper presents a symmetrical topology for the design of solid-state transformer, made up of power switching converters, to replace conventional bulky transformers. The proposed circuitry not only reduces the overall size but also provides power flow control with the ability to be interfaced with renewable energy resources (RESs) to fulfill the future grid requirements at consumer end. Solid state transformer provides bidirectional power flow with variable voltage and frequency operation and has the ability to maintain unity power factor, and current total harmonic distortion (THD) for any type of load within defined limits of IEEE standard. Solid State Transformer offers much smaller size as compared to that of the conventional iron core transformer. MATLAB/Simulink platform is adopted to test the validity of the proposed circuit for different scenarios by providing the simulation results evaluated at 25 kHz switching frequency.

Fragmentation processes of multiply charged ions of C10H8 isomers produced in fast proton collision (velocity between 1.41 and 2.4 a.u.) is discussed in view of their fundamental molecular dynamics. Especially so in the mechanisms to produce a variety of carbon clusters from such ions. This aspect is assessed with the help of a multihit analysis of daughter ions in coincidence with elimination of H+ and CHn+ (n = 0 to 3). The elimination of H+/C+ was found to be very different from CH3+ loss. The loss of CH3+ was found to be accompanied with the formation of heavy ions like C9H5+, C9H5++ and C7H3+ by a cascade of momentum correlated dissociations. The most probable structures of large fragment ions in the CH3+ loss cascade are predicted with the help of computed electronic energy and the multihit ToF correlations of second and third hit. In addition, we report observation of super-dehydrogenation of naphthalene and azulene targets, with evidence of complete dehydrogenation in a single collision.

This paper proposes a multi-terminal adaptive collaborative operation method to solve the problem of unstable internal force tracking in clamping and handling unknown objects by multi-terminal robots. In the proposed method, the internal command force changes the complex internal force control problem into an internal force tracking problem from multi-slave to master. Moreover, we develop an algorithm for multi-slave setups to estimate object stiffness and motion uncertainty in the direction of the internal command force according to Lyapunov theory. Finally, the impedance control generates a reference trajectory for the multi-slave to maintain the desired internal force and track the master’s motion. Several experiments are conducted on a self-made robot equipped. The experimental results show that the oscillation amplitude of each slave end is less than 1 mm, the directional oscillation amplitude is less than 1 degree during the tracking of the desired commanded internal force. For objects with low stiffness, the error of the commanded internal force is less than 1 N (6%) per slave. The error in tracking the commanded internal force for objects with high stiffness is less than 2 N (8%). The results prove the feasibility and effectiveness of the proposed method.

In gravitational theory and astrophysical dynamics, singular initial value problems (IVPs) are frequently encountered. Finding the solutions to this class of IVPs can be challenging due to their complex nature. This study strives to circumvent the complexity by proposing a numerical method for solving such problems. The approach proposed in the current research seeks solutions to the IVP by partitioning the domain [0,L] of the problem into two intervals and solving the problem on each domain. The study seeks a closed-form solution to the IVP in the interval containing the singular point. A linearization technique and piecewise partitioning of the domain not containing the singularity are applied to the nonlinear IVP. The resulting linearized differential equation is solved using the Chebyshev spectral collocation method. Some examples are presented to illustrate the efficiency of the proposed method. Numerical analysis of the solution and residual errors are shown to ascertain convergence and accuracy. The results suggest that the technique gives accurate convergent solutions using a few collocation points.

Dracunculiasis (also known as Guinea worm disease) is caused by Dracunculus medinensis parasite and it spreads by drinking water containing Larvae of Guinea worm. The lack of safe water facilities, preventions and treatments resulted in highly dangerous consequences in its endemic regions. The economy of the affected regions totally falls down due to less production which is the result of agricultural field worker’s bad health. In this study, a multi epitope vaccine was designed against Dracunculus medinensis by using immune-informatics. The vaccine was designed by using T-Cell and B-Cell epitopes derived from Dracunculus medinensis proteins (Lactamase-B domain-containing protein, G-Domain containing protein and Ferrochelatase) in addition to Adjuvants and Linkers. The tertiary structure, physiochemical properties and immunogenic elements of vaccine were achieved. The validation of tertiary structure was accessed, and quality was achieved. In addition, the world coverage of parasite’s CTL and HTL epitopes is 95.61%. The stability of the chimeric vaccine was achieved through disulfide engineering. The molecular docking with Toll Like Receptor 4 (TLR-4) of vaccine showed its binding efficiency followed by Molecular Dynamic Simulation. The immune simulation suggested the mediated cell immunity and repeated antigen clearance. At the end, the optimized codon was used in in silico cloning to ensure vaccine’s higher exposure in bacterium E. coli strain K12. With further assessments, it is believed that the proposed multi epitope vaccine has strong immunogen to control Dracunculus medinensis which may result in better social and economic conditions of endemic regions.

Introduction Tuberculosis is common in Pakistan. Due to various factors including socioeconomic factors, compliance is poor to anti-tuberculosis drugs, leading to resistance. We aim to determine the prevalence of Multidrug resistance (MDR) tuberculosis in Pakistani population.Methods A prospective observational study was conducted from April 1, 2019, to December 31, 2019, in the Pulmonology department of a tertiary care hospital in Pakistan. Culture and sensitivity were assessed using a sputum sample or, in cases of an absent sputum sample, from Broncho alveolar lavage.ResultsApproximately 71.3% percent patients who had tuberculosis were found to be resistant to Isoniazid and around 48.6% did not respond to Rifampin. Multi-drug resistant was found in 29.4% participants.ConclusionMulti-drug resistance tuberculosis is very prevalent in Pakistan, which may increase burden on health care system and may lead to various complications of tuberculosis.

Phenotypic studies require large datasets for accurate inference and prediction. Collecting plant data in a farm can be very labor intensive and costly. This paper presents the design, architecture (hardware and software) and deployment of a distributed modular agricultural multi-robot system for row crop field data collection. The proposed system has been deployed in a soybean research farm at Iowa State University.

In the framework of maritime surveillance, vessel detection techniques based on spaceborne Synthetic Aperture Radar (SAR) images have promoted extensive applications for the effective understanding of unlawful activities at sea. The paper deal with this topic presenting a novel approach exploiting a cascade application of a pre-screening, and discrimination phase. The latter leverage the SAR spectrum by means of sub-looks analysis. For the first time, the method has been validated with experiments on multi-frequency (C-, X-, and L-band) SAR images. For a future syngergic exploitation of more SAR missions, the developed dataset, composed of Sentinel-1, SAOCOM and COSMO-SkyMed images, is comprehensive of multiple images gathered over the same area with short time lag (below 15 minutes). Finally, the diversified processing chains and the results for each mission product and scenarios are discussed. Being the first dataset of SLC (Single Look Complex) SAR multi-frequency data, the present work intends to encourage additional research in this promising field of research.

This research aimed to compare the measurements recorded by a traditional PCI technology biometer (Partial Coherence Interferometry) and by a SS-OCT (Swept Source Optical Coherence Tomography) technology machine in preoperative screening of patients with age-related cataract. Optical biometry was performed with the IOLMaster 500 (version 5.5, Carl Zeiss Meditec, Germany) and the ANTERION (Heidelberg Engineering, Germany) in a total sample of 144 eyes, from 80 patients, (37 men and 43 women), with a mean age of 70.54 ± 0.739 years (range: 45-89 years) and the values of the Axial Length (AL), two meridians of the cornea (Kf, Kflat and Ks, Ksteep), astigmatism (Ast) as well as the Anterior Chamber Depth (ACD) were compared with the program IBM SPSS Statistics 27. The IOLMaster500 and ANTERION devices did not have statistically significant differences in terms of axial length and flat corneal meridian Kf, while they differed statistically significantly in terms of steep corneal meridian Ks, astigmatism and anterior chamber depth. This study suggests that a thorough pre-operative check must be performed, sometimes with more than one device, aiming at greater accuracy in the measurements of the ocular biometrics, so that we achieve more successful postoperative outcomes and ultimately more satisfied patients.

Infant electrocardiograms (ECG) and heart rates (HR) are very useful biosignals for psychological research and clinical work, but can be hard to analyze properly, particularly long form (≥5 minutes) recordings taken in naturalistic environments. Infant HRs are typically much faster than adult HRs, and so some of the underlying frequency assumptions made about adult ECGs may not hold for infants. However, the bulk of publicly available ECG approaches focus on adult data. Here, existing open-source ECG approaches are tested on infant datasets. The best performing open-source method is then modified to maximize its performance on infant data (e.g., including a 15Hz high pass filter, adding local peak correction). The HR signal is then subsequently analyzed, developing an approach for cleaning data with separate sets of parameters for the analysis of cleaner and noisier HR. A Signal Quality Index (SQI) for HR is also developed, providing insight into where a signal is recoverable and where it is not, allowing for more confidence in analysis performed on naturalistic recordings. The tools developed and reported in this paper provide a base for future analysis of infant ECG and related biophysical characteristics. Of particular importance, the proposed solutions outlined here can be efficiently applied to real-world large datasets.

The latest experimental measurements of cosmic rays (CRs) have discovered a series of anomalies, including the hardening of the nuclear spectra at R ∼200 GV followed by softening at R ∼10 TV and complicated energy dependence of anisotropy from GeV to PeV. Recent works have demonstrated nearby sources are crucial for these anomalies of spectra and anisotropy. In this work, we analyze the contributions of five nearby sources within 1 kpc around solar system to the spectra and anisotropy, finally find out which source is the best candidate source. In the calculation process, we also introduce the anisotropic diffusion of CRs induced by the local interstellar magnetic field (LIMF) nearby the solar system based on spatial-dependent propagation (SDP) model. As a result, we find Geminga SNR source can simultaneously account for CR spectra and anisotropy, whereas the other sources can not . Measurements of CR anisotropy and spectra by experiments such as LHAASO and HAWC are expected to test this scenario in the near future.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

To solve the problem of low efficiency of source seeking in implicit information field, this paper presents an autonomous souring method based on balanced searching strategy is enlighten by biological homing behaviors. At the beginning of the research, the source seeking task come down to a multi-objective convergence issue. By taking the feasibility search behaviors as the individual sample of the evolutionary population drawing on the thought of evolutionary algorithms, then combine motion searching with population evolution, so the carrier can be guide to complete source seeking task by solving the multi-objective problem. Furthermore, the distribution entropy is also considerated d to measure the searching bias in the process of source seeking. Combined with the demand of the source seeking process, a new source seeking method of balanced searching strategy is designed. Ultimately, through theoretical analysis and simulation verification confirm the effectiveness and rationality of the proposed method.

The purpose of this study is to characterize atmospheric pollution and its sources in two West African urban sites during the dry season (January 2009 in Bamako, Mali, and December 2009 in Dakar, Senegal). Particulate Matter (PM) source apportionment was performed using Principal Component Analysis (PCA) and Positive Matrix Factorization (PMF). Carbonaceous components, water-soluble inorganic compounds, and trace elements were analyzed from PM (TSP, PM10, and PM2.5) samples. The measured PM2.5 and PM10 concentrations were 5 to 10 times and 3 to 8 times higher than the 2005 WHO 24-hour standards, respectively. PCA and PMF analyses identify five sources in both cities. The sources contributing to aerosol concentrations (PM2.5 - PM10) in Bamako are motor vehicles (20-13%), solid fuel combustion (16-13%), crustal dust (24-30%), resuspended road dust (26-30%) and secondary aerosols (10-16%). During the sampling period in Bamako, dust was the most prevalent source, accounting for 63% of the total PM10 mass. In Dakar, the main identified sources were motor vehicles (28-19%), mineral dust (16-25%), industries and oil burn-ing (11-10%), sea salts (15-20%), and resuspended road particles (21-29%). The findings also indicate that anthropogenic emissions contribute significantly to the PM2.5 fraction, implying that populations are highly exposed to fine particles.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

Cognitive biases are an important factor contributing to the development and symptom severity of psychosis. Despite that various cognitive biases are contributing to psychosis, they are rarely investigated together. In the current systematic review, we aimed at investigating specific and shared neural correlates of two important cognitive biases: aberrant salience and source monitoring. We conducted a systematic search of fMRI studies of said cognitive biases. Eight studies on aberrant salience and eleven studies on source monitoring were included in the review. We critically discussed behavioural and neuroimaging findings concerning cognitive biases. Various brain regions are associated with aberrant salience and source monitoring in individuals with schizophrenia and the risk of psychosis. Ventral striatum and insula contribute to aberrant salience. The medial prefrontal cortex, superior and middle temporal gyrus contribute to source monitoring. The anterior cingulate cortex and hippocampus contribute to both cognitive biases, constituting a neural overlap. Our review indicates that aberrant salience and source monitoring may share neural mechanisms, suggesting their joint role in producing disrupted external attributions of perceptual and cognitive experiences, thus elucidating their role in positive symptoms of psychosis. Account bridging mechanisms of these two biases is discussed. Further studies are warranted.

The CARA program has been developed since 2008 by the French reference laboratory for air quality monitoring (LCSQA) and the regional monitoring networks to gain a better knowledge at the national level on the particulate matter (PM) chemistry and its diverse origins in urban environments. It results of strong collaborations with international-level academic partners, allowing to bring state-of-the-art, straightforward and robust results and methodologies within operational air quality stakeholders (and subsequently, decision makers). Here, we illustrate some of the main outputs obtained over the last decade thanks to this program, regarding methodological aspects (both in terms of measurement techniques and data treatment procedures) as well as acquired knowledge on the predominant PM sources. Offline and online methods are used following well-suited quality assurance and quality control procedures, notably including inter-laboratory comparison exercises. Source apportionment studies are conducted using various receptor modeling approaches. Overall, the results presented herewith underline the major influences of residential wood burning (during the cold period) and road transport emissions (exhaust and non-exhaust ones, all along the year), as well as substantial contributions of mineral dust and primary biogenic particles (mostly during the warm period). Long-range transport phenomena, e.g., advection of secondary inorganic aerosols from the European continental sector and of Saharan dust into the French West Indies, are also discussed in this paper. Finally, we briefly address the use of stable isotope measurements (δ15N) and of various organic molecular markers for a better understanding of the origins of ammonium and of the different organic aerosol fractions, respectively.

Small Shallow Lakes (SSL) support exceptionally high and original biodiversity, providing numerous ecosystem services. Their small size makes them especially sensitive to anthropic activities, that causes a shift to dysfunctional turbid states and induces loss of services and biodiversity. In this study we investigated the relationships between environmental factors and macrophyte communities. Macrophytes play a crucial role in maintaining functional clear states. Better understanding factors determining the composition and richness of aquatic plant communities in least-impacted conditions may be useful to protect them. We inventoried macrophyte communities and collected chemical, climatic and morphological data from 89 least-impacted SSL widely distributed in France. SSL were sampled across four climatic ecoregions, various geologies and elevations. Hierarchical cluster analysis showed a clear separation of four macrophyte assemblages strongly associated with mineralisation. Determinant factors identified by db-RDA analysis are, in order of importance, geology, distance from source (DIS, a proxy for connectivity with river hydrosystems), surface area, climate and hydroperiod (water permanency). Surprisingly, at country-wide scale, climate and hydroperiod filter macrophyte composition weakly. Geology and DIS are the major determinants of community composition, whereas surface area determines floristic richness. DIS is identified as determinant in freshwater lentic ecosystems for the first time.

This paper aims to investigate the airflow that can transport emission sources of PM2.5 from neighboring countries to contribute to air pollution in northern Thailand. We applied the coupled atmospheric and air pollution model which is based on the Weather Research and Forecasting Model (WRF) and a Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT). The model output was compared to the ground-based measurement from the Pollution Control Department (PCD) to examine model performance. As a result of model evaluation, the meteorological variables fairly agreed well compared to observation with Index of Agreement (IOA) in ranges of 0.57 to 0.79 for temperature and 0.32 to 0.54 for wind speed, while the fractional bias of temperature and wind speed were 1.3 to 2.5 °C and 1.2 to 2.1 m/s. Burma was a country that contributed much of hotpot locations by 37% of the entire hotspot locations of Southeast Asia in March. The influence of the Asian Monsoon can bring pollutants from neighboring countries such as Burma and Laos toward northern Thailand in March that likely contribute to high concentrations of PM2.5 in northern Thailand.

(1) Background: In nervous system information is conveyed by a sequence of action potentials, called spikes-trains. As MacKay and McCulloch proposed, spike-trains can be represented as bits sequences coming from Information Sources. Previously, we studied relations between Information Transmission Rates (ITR) carried out by the spikes, their correlations, and frequencies. Here, we concentrate on the problem of how spikes fluctuations affect ITR. (2) Methods: The Information Theory Method developed by Shannon is applied. Information Sources are modeled as stationary stochastic processes. We assume such sources as two states Markov processes. As a spike-trains' fluctuation measure, we consider the Standard Deviation sigma, which, in fact, measures average fluctuation of spikes around the average spike frequency. (3) Results: We found that character of ITR and signal fluctuations relation strongly depends on the parameter s which is a sum of transitions probabilities from no spike state to spike state and vice versa. It turned out that for smaller s (s<1) the quotient ITR\sigma has a maximum and can tend to zero depending on transition probabilities. While for s large enough (1<s) the ITR\sigma is separated from 0 for each s. Similar behavior was observed also when we replaced Shannon entropy terms in Markov entropy formula by their approximation with polynomials. We also show that the ITR quotient by Variance behaves in a completely different way. (4) Conclusions: Our results show that for large transition parameter s the Information Transmission Rate by sigma will never decrease to zero. Specifically, for 1<s<1.7 the ITR will be always, independently on transition probabilities which form this s, above the level of fluctuations, i.e. in this case we have sigma<ITR. Thus, we conclude that in a more noisy environment, to get appropriate reliability and efficiency of transmission, Information Sources with higher tendency of transition from the state no spike to spike state and vice versa should be applied.

The importance of ICTs for dissemination of information to farmers has been verified by extension practitioners, information and communication scholars, policy makers and development agencies. Information related to new seed varieties, production technologies, livestock breeds, vaccines, including weed and pest control, as well as relevant market information is constantly required by smallholder farmers. The identification of specific attributes among smallholder farmers which contributes to their adoption of a proposed ICT-based information source provides an important tool for developing interventions which address the information needs of farmers. Using a literature survey methodology, pertinent studies related to adoption of ICTs, farmers’ information source usage and relevant frameworks were identified, including applicable theories and models in technology adoption and information behaviour. In the proposed framework, the socio-economic characteristics of smallholder farmers were posited as key variables influencing smallholder farmers, within a farming system, to adopt ICT-based information sources. The framework contributes to discern the prospects of adopting ICT-based information sources by individual farmers within a farming system, and may also envisage other related welfare outcomes and market participation pathways among smallholder farmers. The review also addresses the paucity of conceptual discourse, while contributing to a growing pool of research on ICT in African agriculture.

Several studies have shown that changes in incoming solar radiation and variations of the diffuse fraction can significantly modify the vegetation carbon uptake. Hence, monitoring the incoming solar radiation at large scale and with high temporal frequency is crucial for this reason along with many others. The EUMETSAT Satellite Application Facility for Land Surface Analysis (LSA SAF) operationally disseminates in near real time estimates of the downwelling shortwave radiation at the surface since 2005. This product is derived from observations provided by the SEVIRI instrument onboard the Meteosat Second Generation series of geostationary satellites, which covers Europe, Africa, the Middle East, and part of South America. However, near real time generation of the diffuse fraction at the surface level has only recently been initiated. The main difficulty towards achieving this goal was the general lack of accurate information on the aerosol particles in the atmosphere. This limitation is nowadays less important thanks to the improvements in atmospheric numerical models. This study presents an upgrade of the LSA-SAF operational retrieval method, which provides the simultaneous estimation of the incoming solar radiation and its diffuse fraction from satellite every 15 minutes. The upgrade includes a comprehensive representation of the influence of aerosols based on physical approximations of the radiative transfer within an atmosphere-surface associated medium. This article explains the retrieval method, discusses its limitations and differences with the previous method, and details the characteristics of the output products. A companion article will focus on the evaluation of the products against independent measurements of solar radiation. Finally, the access to the source code is provided through an open access platform in order to share with the community the expertise on the satellite retrieval of this variable.

This study aimed to investigate the airborne release of N-nitrosodimethylamine (NDMA) as a result of the dry heat cooking of some meats using charcoal grilling and pan broiling methods. Three types of meat, beef sirloin, pork belly, and duck, were chosen and cooked in a temporary building using the above methods. Air samples were collected in Thermosorb-N cartridges, which were qualitatively and quantitatively analyzed for NDMA using ultra-high performance liquid chromatography–mass spectrometry and high-performance liquid chromatography–fluorescence detection, respectively. Overall, the charcoal grilling method showed higher average NDMA concentrations than the pan broiling method for all types of meat. The highest average concentration was observed for charcoal-grilled beef sirloin (410 ng/m3) followed by pork belly, suggesting that meat protein content and cooking duration are important determinants of NDMA formation. Cancer risk assessment showed that the charcoal grilling of such meats can pose an additional cancer risk for restaurant customers.

In this study, a matched-mode autoregressive source depth estimation method (MMAR) based on autoregressive (AR) wavenumber estimation is proposed for a moving source in shallow water waveguides. The signal original frequency and the environmental parameters, namely, the sound speed profile and bottom properties are known as a prior knowledge. The mode wavenumbers are estimated by the AR modal wavenumber spectrum. On the basis of the mode wavenumber estimation, the mode amplitudes can be estimated by the wavenumber spectrum that is obtained by generalized Hankel transform. The source depth estimation is determined by the peak of source depth function wherein the data mode best matches the replica mode that is calculated using a propagation model. Compared with other methods of moving source depth estimation, the proposed method exhibits a better performance in source depth estimation under low signal-to-noise ratio or the small range span. The selection of horizontal line array depth is illustrated by simulation and normal mode theory in details.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Porous ceramics can be realized by different methods and are used for manifold applications, like cross-flow-membranes or wall-flow-filters, porous burners, solar receivers, structural design elements or catalytic supports. Within this paper three different alternative process routes are presented, which can be used to manufacture porous ceramic components with different properties or even graded porosity. The first process route bases on additive manufacturing (AM) of macro porous ceramic components, the second on AM of a polymeric template, which is used to manufacture porous ceramic components via replica technique. Finally, the third process route bases on an AM technology, which allows the manufacturing of multi-material or multi-property ceramic components, like components with dense and porous volumes in one complex shaped component.

In this article, we introduce some multi-messenger studies of blazars. Main contents contain the following parts, 1. the subclasses of blazars and the observational characteristics, 2. emission variabilities from the multi-messenger observations, 3. the physical origin for the multi-messenger studies. Based on mid-IR observations collected from the $WISE$ database, we collect two sources (BZQ J1700+6830 and BZQ J1842+6809) to analyze the mid-IR variabilities. \\ (1) For BZQ J1700+6830, the period is $P\approx$ 42 hr at the four bands ($W1$, $W2$, $W3$, $W4$); for BZQ J1842+6809, the period is $P\approx$ 123 hr at the two bands ($W1$, $W2$). \\ (2) Using the periodicities, we calculate that the central black hole mass ($BH$) should be $M = (5.44\sim33.0)\times10^8M_{\odot}$ for BZQ J1700+6830 and $M = (1.13\sim6.88)\times10^9M_{\odot}$ for BZQ J1842+6809.\\ (3) For the two sources, during the flaring stage, we find anti-clockwise variation trends based on the time-based relations built by the spectral indices ($\alpha$) and flux densities ($F$).\\ (4) We calculate the Doppler factor ($\delta$) when the sources are in the dimming or brightening stages, and find that with the frequency increasing, the Doppler factor become stronger.

The paper considers new effects of the nanoscale state of matter, which open up prospects for the creation of electronic devices using new physical principles. The contact of chemically homogeneous different sizes hydrated nanoparticles of yttrium-stabilized zirconium oxide (ZrO2 – x %mol Y2O3, x=0, 3, 4, 8; YSZ) with particle sizes of 7.5 nm and 7,5 nm; 7.5 nm and 9 nm; 7.5 nm and 11 nm; 7.5 nm and 14 nm in the form of compacts obtained using high hydrostatic pressure (HP-compacts of 300MPa) was studied at direct and alternating current. A unique size effect of the nonlinear (semiconductor) dependence of the electrical properties (in the region U <2.5 V, I ≤ 2.7 mA) of the contact of different-sized YSZ nanoparticles of the same chemical composition is revealed, which indicates the possibility of creating semiconductor structures of a new type based on chemically homogeneous nanostructured systems. The electronic structure of the near-surface regions of nanoparticles of a special type of oxide materials and the possibility, on this basis, to obtain specifically rectifying properties of the contacts were studied theoretically. Models of surface states of the Tamm type are constructed, but considering the Coulomb long-range action. The discovered variance and its dependence on the curvature of the surface of nanoparticles made it possible to study the conditions for the formation of a contact potential difference in cases of nanoparticles of the same radius (synergistic effect), different radii (doped and undoped variants), as well as to discover the possibility of describing a group of powder particles from material within the Anderson model. The established effect makes it possible to solve the problem of diffusion instability of semiconductor heterojunctions and opens up prospects for creating electronics devices with a fundamentally new level of properties for use in various fields of the national economy and breakthrough critical technologies.

Fluorescence microscopy provides an unparalleled tool for imaging biological samples. However, producing high-quality volumetric images quickly and without excessive complexity remains a challenge. Here, we demonstrate a simple multi-camera structured illumination microscope (SIM) capable of simultaneously imaging multiple focal planes, allowing for the capture of 3D fluorescent images without any axial movement of the sample. This simple setup allows for the acquisition of many different 3D imaging modes, including 3D time lapses, high-axial-resolution 3D images, and large 3D mosaics.

Our work uses Iterative Boltzmann Inversion (IBI) to study the coarse-grained interaction between 20 amino acids and the representative carbon nanotube CNT55L3. IBI is a multi-scale simulation method that has attracted the attention of many researchers in recent years. It can effectively modify the coarse-grained model derived from the Potential of Mean Force (PMF). IBI is based on the distribution result obtained by All-Atom molecular dynamics simulation, that is, the target distribution function, the PMF potential energy is extracted, and then the initial potential energy extracted by the PMF is used to perform simulation iterations using IBI. Our research results have gone through more than 100 iterations, and finally, the distribution obtained by coarse-grained molecular simulation (CGMD) can effectively overlap with the results of all-atom molecular dynamics simulation (AAMD). In addition, our work lays the foundation for the study of force fields for the simulation of the coarse-graining of super-large proteins and other important nanoparticles.

Multi-morbidity and polypharmacy are common in older people and pose a challenge for health and social care systems especially in context of global population ageing. They are complex and interrelated concepts in the care of older people that require early detection and patient centred decision making that are underpinned by the principles of multidisciplinary led comprehensive geriatric assessment (CGA). Personalised care plans need to remain responsive and adaptable to the needs of a patient, enabling an individual to maintain their independence.

This paper presents a new and enhanced fusion module for the Multi-Sensor Precipitation Estimator (MPE) that would objectively blend real-time satellite quantitative precipitation estimates (SQPE) with radar and gauge estimates. This module consists of a preprocessor that mitigates systematic bias in SQPE, and a two-way blending routine that statistically fuses adjusted SQPE with radar estimates. The preprocessor not only corrects systematic bias in SQPE, but also improves the spatial distribution of precipitation based on SQPE and makes it closely resemble that of radar-based observations. It uses a more sophisticated radar-satellite merging technique to blend preprocessed datasets, and provides a better overall QPE product. The performance of the new satellite-radar-gauge blending module is assessed using independent rain gauge data over a 5-year period between 2003-2007, and the assessment evaluates the accuracy of newly developed satellite-radar-gauge (SRG) blended products versus that of radar-gauge products (which represents MPE algorithm currently used in the NWS operations) over two regions: I) inside radar effective coverage and II) immediately outside radar coverage. The outcomes of the evaluation indicate a) ingest of SQPE over areas within effective radar coverage improve the quality of QPE by mitigating the errors in radar estimates in region I; and b) blending of radar, gauge, and satellite estimates over region II leads to reduction of errors relative to bias-corrected SQPE. In addition, the new module alleviates the discontinuities along the boundaries of radar effective coverage otherwise seen when SQPE is used directly to fill the areas outside of effective radar coverage.

Code summarization plays a vital role in aiding developers with program comprehension by generating corresponding textual descriptions for code snippets. While recent approaches have concentrated on encoding the textual and structural characteristics of source code, they often neglect the global hierarchical features causing limited code representation. Addressing this gap, our paper introduces the Statement-grained Hierarchy enhanced Transformer model (SHT), a novel framework that integrates global hierarchy, syntax, and token sequences to automatically generate summaries for code snippets. SHT is distinctively designed with two encoders to learn both hierarchical and sequential features of code. One relational attention encoder processes the statement-grained hierarchical graph, producing hierarchical embeddings. Subsequently, another sequence encoder integrates these hierarchical structures with token sequences. The resulting enriched representation is then fed into a vanilla Transformer decoder, which effectively generates concise and informative summarizations. Our extensive experiments demonstrate that SHT significantly outperforms state-of-the-art approaches on two widely used Java benchmarks. This underscores the effectiveness of incorporating global hierarchical information in enhancing the quality of code summarizations.

Digital music is one of the most important things in market due to the music royalties’ distribution in Korea. As the music market is transformed to the digital music market such as download the music and streaming, the distribution of music royalties starting from online service provider (OSP) has come to be a highly important part for music rights holders. One of the most important issues in current music royalties’ distribution in Korea is the unfair way of music royalties due to indiscriminative repeat streaming of digital music. To prevent this, music log usage data from several OSPs was collected in day-based system, however, there was a limit to identify detailed information on the use of music in current state. This paper analyzed the structural problems and limitations of settlement of music royalties, and provides a structure in which there can be transparent settlement and distribution between users and rights holders as one of the institutional measures. We’ll also propose various AI-based applications using music log usage data. The proposed system will hopefully be used for public purposes.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photons flux of 106 photons/s of commercial VUV lamp limits its range of ionizable analytes as well as sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp through the photoelectric effect ionized the oxygen in the air to obtain the reagent ions O2+, and segmented quadrupole constituted the ion-molecule-reaction region (IMR) and radially focused the ions using a radio-frequency electric field, which improved the yield and transport efficiency of the sample ions and the sensitivity of mass spectrometry, resulting in 44-fold and 1154-fold increase in signal response to benzene and pentanal, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the concentration range of 5-50 ppbv, and daytime RSD reached 3.91% and 6.26%, respectively. Finally, the CIFI ionization source TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs can reach the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

Groundwater plays a crucial role in triggering and reactivating deep-seated landslides. However, classical hydrogeological investigations have limitations in their applicability to deep-seated landslides due to anisotropic and heterogeneous media[16]. The Huangtupo landslide in the Three Gorges reservoir area has garnered significant attention in China due to its large volume, complex geological structure, and high hazard potential. Recent monitoring data has shown notable deformation in the NO.1 Riverside Sliding Mass (HTP-1), one of the four parts of the Huangtupo landslide, making it the primary focus of landslide research. This study aimed to investigate the water sources in the HTP-1 landslide using environmental stable isotopes as tracers. The isotopic analysis results indicated that the groundwater in the landslide area (LGW) is a mixture of remote karst groundwater (KGW) from the adjacent up-slope and local precipitation (LP). The karst groundwater is a major contributor to the recharge of the landslide groundwater system, causing a high slope groundwater level that can easily exceed the critical level during heavy rainfall events. Furthermore, based on the differential distribution of the LP fraction of LGW at different locations, the groundwater in the landslide can be classified into three groups. Groundwater at the sliding rupture surface has the highest fractions of local precipitation, followed by the groundwater at the rear of the landslide. Combined with the monitoring data of groundwater level in boreholes during the rainy season, this indicates that fissures and fractures in the sliding rupture zone and at the back of the landslide are well connected, which could be a critical factor in the mass movement of the creeping slope.

The Coronavirus disease 2019 (COVID-19) rapidly spread to over 180 countries and abruptly disrupted the production rates and supply chains worldwide. Since then, 3D printing also recognized as additive manufacturing (AM) and known to be a novel technique that uses layer-by-layer deposition of material to produce the intricate 3D geometry, has been engaged in reducing the distress caused by the outbreak. During the early stages of this pandemic, shortages of Personal Protection Equipment (PPE), including facemasks, shields, respirators, and other medical gears, were significantly answered by remotely 3D printing them. Amidst the growing testing requirements, the 3D printing emerged as a potential and fast solution manufacturing process to meet the production needs due to its flexibility, reliability, and rapid response capabilities. In the recent past, some of the other medical applications that have gained prominence in the scientific community include 3D printed ventilator splitters, device components, and patient-specific products. Regarding the non-medical applications, researchers have successfully developed contact-free devices to address the sanitary crisis in public places. This work aims to systematically review the applications of 3D printing or AM techniques that have been involved in producing various critical products essential to limit this deadly pandemic's progression.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

3D object reconstruction from depth image streams using Kinect-style depth cameras has been extensively studied. In this paper, we propose an approach for accurate camera tracking and volumetric dense surface reconstruction assuming a known cuboid reference object is present in the scene. Our contribu¬tion is three-fold. (a) We maintain drift-free camera pose tracking by incorporating the 3D geometric constraints of the cuboid reference object into the image registration process. (b) We reformulate the problem of depth stream fusion as a binary classification problem, enabling high-fidelity surface reconstruction, especially in the con¬cave zones of objects. (c) We further present a surface denoising strategy to mitigate the topological inconsistency (e.g., holes and dangling triangles), which facilitates the generation of a noise-free triangle mesh. We extend our public dataset CU3D with several new image sequences, test our algorithm on these sequences and quantitatively compare them with other state-of-the-art algorithms. Both our dataset and our algorithm are available as open-source content at https://github.com/zhangxaochen/CuFusion for oth-er researchers to reproduce and verify our results.

The urbanisation phenomenon and related cities expansion and transport networks entail preventing the increase of population exposed to environmental pollution. Regarding noise exposure, the Environmental Noise Directive demands on main metropolis to produce noise maps. While based on standard methods, these latter are usually generated by proprietary software and require numerous input data concerning, for example, the buildings, land use, transportation network and traffic. The present work describes an open source implementation of a noise mapping tool fully implemented in a Geographic Information System compliant with the Open Geospatial Consortium standards. This integration makes easier at once the formatting and harvesting of noise model input data, cartographic rendering and output data linkage with population data. An application is given for a French city, which consists in estimating the impact of road traffic-related scenarios in terms of population exposure to noise levels both in relation to a threshold value and level classes.

Bioelectrocatalysis provides the intrinsic catalytic-functions of redox enzymes to non-specific electrode reactions and is the most important and basic concept for biosensors. This review starts by describing fundamental characteristics of bioelectrocatalytic reactions in mediated and direct electron transfer types from a theoretical viewpoint and summarizes amperometric biosensors based on multi-enzymatic cascades and for multi-analyte detection. The review also introduces prospective aspects of two new concepts of biosensors: mass-transfer-controlled (pseudo)steady-state amperometry at microelectrodes with enhanced enzymatic activity without calibration curves and potentiometric coulometry at enzyme/mediator-immobilized biosensors for absolute determination.

This article proposes the use of a multi-scale and multi-sensor approach to collect and modelling 3D data concerning wide and complex areas in order to obtain a variety of metric information in the same 3D archive, based on a single coordinate system. The employment of these 3D georeferenced products is multifaceted and the fusion or integration among different sensors data, scales and resolutions is promising and could be useful for the generation of a model that could be defined as hybrid. The correct geometry, accuracy, radiometry and weight of the data models are hereby evaluated comparing integrated processes and results from Terrestrial Laser Scanner (TLS), Mobile Mapping System (MMS), Unmanned Aerial Vehicle (UAV), terrestrial photogrammetry, using Total Station (TS) and Global Navigation Satellite System (GNSS) as topographic survey. The entire analysis underlines the potentiality of the integration and fusion of different solutions and is a crucial part of the “Torino 1911” project whose main purpose is mapping and virtually reconstructing the 1911 Great Exhibition settled in the Valentino Park in Turin (Italy).

Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, costs of the former and required electricity to operate the latter, limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified and reliable lab-scale centrifuge. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class fused filament fabrication (FFF) or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open source software. This paper provides the complete open source plans including instructions for fabrication and operation for a hand-powered centrifuge. This study successfully tested and validated the instrument, which can be operated anywhere in the world with no electricity inputs obtaining a radial velocity of over 1750rpm and over 50N of relative centrifugal force. Using commercial filament the instrument costs about US$25, which is less than half of all commercially available systems; however, the costs can be dropped further using recycled plastics on open source systems for over 99% savings. The results are discussed in the contexts of resource-constrained medical and scientific facilities.

Does cell clustering influence intrinsic and acquired multi-drug resistance (MDR) differently? To address this question, we studied cultured monolayers (representing individual cells) and cultured spheroids (representing clusters) formed by drug-naïve (intrinsic MDR) and drug-exposed (acquired MDR) lines of ovarian cancer A2780 cells by cytometry of reaction rate constant (CRRC). MDR efflux was characterized by accurate and robust “cell number vs. MDR efflux rate constant (kMDR)” histograms. Both drug-naïve and drug-exposed monolayer cells presented unimodal histograms; the histogram of drug-exposed cells was shifted towards higher kMDR value suggesting greater MDR activity. Spheroids of drug-naïve cells presented a bimodal histogram indicating the presence of two subpopulations with different MDR activity. In contrast, spheroids of drug-exposed cells presented a unimodal histogram qualitatively similar to that of the monolayers of drug-exposed cells but with a moderate shift towards greater MDR activity. The observed greater effect of cell clustering on intrinsic than on acquired MDR can help guide the development of new therapeutic strategies targeting clusters of circulating tumor cells.

In this paper, we consider a new class of polynomials which is called the multi-poly-Euler polynomials. Then, we investigate their some properties and relations. We provide that the type 2 degenerate multi-poly-Euler polynomials equals a linear combination of the degenerate Euler polynomials of higher order and the degenerate Stirling numbers of the first kind. Moreover, we provide an addition formula and a derivative formula. Furthermore, in a special case, we acquire a correlation between the type 2 degenerate multi-poly-Euler polynomials and degenerate Whitney numbers.

Inspired by the definition of degenerate multi-poly-Genocchi polynomials given by using the degenerate multi-polyexponential functions. In this paper, we consider a class of new generating function for the degenerate multi-poly-Bernoulli polynomials, called the type 2 degenerate multi-poly-Bernoulli polynomials by means of the degenerate multiple polyexponential functions. Then, we investigate their some properties and relations. We show that the type 2 degenerate multi-poly-Bernoulli polynomials equals a linear combination of the weighted degenerate Bernoulli polynomials and Stirling numbers of the first kind. Moreover, we provide an addition formula and a derivative formula. Furthermore, in a special case, we acquire a correlation between the type 2 degenerate multi-poly-Bernoulli numbers and degenerate Whitney numbers.

This study introduces a low-cost solution provided by a specialized source measure unit (SMU), offering an alternative to conventional source meter units. Through precise IV curve measurements for graphene-channel FETs, the SMU demonstrates its capability in accurately characterizing these devices with minimal noise and high accuracy. This cost-effective solution presents a promising avenue for researchers and developers seeking reliable tools for sensor development and characterization, providing valuable insights into the behavior of graphene-channel FETs and the effect of surface illumination without the need for expensive equipment. Additionally, the SMU was validated with known passive and active components, along with probe station integration for microscale connection, ensuring its effectiveness in capturing accurate measurements. The SMU’s focus on collecting IV curves, coupled with its ability to identify device defects, such as Schottky junctions, contributes to its utility in quality testing for semiconductor devices. Its low-cost nature makes it accessible for various research endeavors, enabling efficient data collection and analysis for graphene-based sensor applications.