Co-based catalysts have gained significant attention in recent years due to their excellent ability to activate C-H bonds and high selectivity towards olefins, despite being a non-noble and environmentally unfriendly metal. However, further improvements are necessary for practical utilization, particularly in terms of activity and anti-carbon deposition capacity. In this study, we synthesized Al₂O₃ nanorods with abundant pentacoordinated Al³⁺ (Al³⁺_penta) sites. The supported Co on the Al₂O₃ nanorod (Co/Al₂O₃-NR) exhibited higher selectivity (>96% propylene selectivity) and stability (deactivation rate 0.15 h^-1), compared to Co supported on an Al₂O₃ nanosheet with fewer pentacoordinated Al³⁺ sites. Various characterizations confirmed that Co(II) mainly exists as CoAl₂O₄ rather than Co₃O₄ in the form of Co/Al₂O₃-NR, which inhibits the reduction of Co(II) to Co0 and improves catalyst stability accordingly.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

Endoscopic ultrasound-guided gallbladder drainage (EUS-GBD) is an alternative to surgery for acute cholecystitis (AC) in poor operative candidates. However, the role of EUS-GBD in non-cholecystitis (NC) indications has not been well studied. We compared clinical outcomes of EUS-GBD for AC and NC indications. Consecutive patients undergoing EUS-GBD for all indications at a single center were retrospectively analyzed. Fifty-one patients underwent EUS-GBD during the study period. Thirty-nine (76%) patients had AC while 12 (24%) had NC indications. NC indications included malignant biliary obstruction (n = 8), symptomatic cholelithiasis (n = 1), gallstone pancreatitis (n = 1), choledocholithiasis (n = 1), and Mirizzi’s syndrome (n = 1). Technical success was noted in 92% (36/39) for AC and 92% (11/12) for NC (p > 0.99). Clinical success rate was 94% and 100%, respectively (p > 0.99). There were 4 adverse events in the AC group and 3 in the NC group (p = 0.62). Procedure duration (median 43 vs 45 minutes, p = 0.37), post-procedure length of stay (median 3 vs 3 days, p = 0.97), and total gallbladder related procedures (median 2 vs 2, p = 0.59) were similar. EUS-GBD for NC indications is similarly safe and effective as EUS-GBD in AC.

Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I-V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modelled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 \% to the total degradation rate.

Metallo-β-lactamases (MBLs) are a group of Zn(II)-dependent enzymes that pose a major threat to global health. They are linked to an increasing number of multi-drug resistant bacterial pathogens, but no clinically useful inhibitor is yet available. Since β-lactam antibiotics, which are inactivated by MBLs, constitute ~65% of all antibiotics used to treat infections, the search for clinically relevant MBL inhibitors is urgent. Here, derivatives of a 2-amino-1-benzyl-4,5-diphenyl-1H-pyrrole-3-carbonitrile (1a) were synthesised and their inhibitory effects assessed against representatives of each of the three subgroups of MBLs (B1, B2, B3). Several compounds are potent inhibitors of each MBL tested, making them excellent candidates for the development of broad-spectrum drug leads. In particular, compound 5f is highly potent across the MBL subfamilies, with Ki values in the low µM range. Furthermore, this compound also dis-plays synergy in combination with antibiotics such as penicillin G, cefuroxime or meropenem. This molecule thus represents one of the most promising compounds developed yet to combat MBLs.

Surfaces of additively manufactured metal parts from powder-based processes typically show powder particle agglomerations and other features, resulting in high surface roughness. Proper characterization of those surfaces is necessary in order to assess part quality with respect to coatability, mechanical performance or corrosion resistance for use in aerospace, automotive, medical and more industrial applications. Optical surface texture measurement allows for collection of areal surface data, while the established contact stylus method only captures line profile data. When applying optical methods for surface topography measurements, proper data acquisition and post-processing in order to assess surface texture may be complex. A number of variables can be adjusted, such as different measurement settings, approaches to outlier removal, evaluated area size or form removal. This work shows the influence of selected z-range prior to measurement and the influence of choosing pre-defined outlier removal settings in MountainsMap 9.2 on selected ISO 25178-2:2022 parameters calculated from data obtained from confocal microscopy for as-built Ti6Al4V from laser powder bed fusion. The aim is to show the influence of variation in measurement and post-processing on calculated surface texture parameters and stress the importance of proper documentation in order to achieve reproducibility of data for quality management.

Due to its built-up chemoresistance after prolonged usage, the demand for replacing platinum in metal-based drugs (MBD) is rising. The first MBD approved by the FDA for cancer therapy was cisplatin in 1978. Even after nearly four and a half decades of trials, there has been no significant improvement in osteosarcoma (OS) therapy. In fact, many MBD have been developed, but the chemoresistance problem raised by platinum remains unresolved. This motivates us to elucidate the possibilities of the copper and zinc (CuZn) combination to replace platinum in MBD. Thus, the anti-chemoresistance properties of CuZn and their physiological functions for OS therapy are highlighted. Herein, we summarise their chelators, main organic solvents, and ligand functions in their structures that are involved in anti-chemoresistance properties. Through this review, it is rational to discuss their ligands’ roles as biosensors in drug delivery systems. Hereafter, an in-depth understanding of their redox and photoactive function relationships is provided. The disadvantage is that the other functions of biosensors cannot be elaborated on here. As a result, this review is being developed, which is expected to intensify OS drugs with higher cure rates. Nonetheless, this advancement intends to solve the major chemoresistance obstacle towards clinical efficacy.

The flavin derivatives 10‐methyl‐isoalloxazine (MIA) and 6-fluoro-10-methyl-isoalloxazine (6F-MIA) were encapsulated in two alternative metal-organic frameworks, (MOFs) MIL53(Al) and MOF5, using a post-synthetic, diffusion-based incorporation into microcrystalline MIL-53 powders and an in-situ approach during the MOF-5 synthesis. The flavin@MOF composites were analyzed by powder X-ray diffractometry (PXRD), N2-sorption studies and time-resolved fluorescence spectroscopy and microscopy. The maximum amount of flavin dye incorporation is 3.9 wt% for MIA@MIL-53(Al) and 1.5 wt% for 6F-MIA@MIL-53(Al), 0.85 wt% for MIA@MOF-5 and 27.6 wt% for 6F-MIA@MOF-5. The emission wavelengths of all flavin@MOF composites mostly correspond to the wavelengths of the flavins in solution. Time-resolved spectroscopy showed that the fluorescence lifetime of flavin@MOF of 2-4.7 ns also corresponds to those in solution but is significantly prolonged compared to the solid flavin dyes with less than 1 ns, thereby confirming the concept of "solid solutions" for dye@MOF composites. The fluorescence quantum yield (ΦF) of the flavin@MOF composites is about half of the solution but is significantly higher compared to the solid flavin dyes. Both the fluorescence lifetime and quantum yield of flavin@MOF decrease with the flavin loading in MIL-53. Theoretical calculations using plane-wave and QM/MM methods are in good correspondence with the experimental results and explain the electronic structures as well as the photoluminescence/photophysical properties of crystalline MIA and the flavin@MOF composites. In the solids flavins π-stacking interactions of the molecules lead to a charge transfer state with low oscillator strength resulting in aggregation-caused quenching (ACQ) with low lifetimes and quantum yields. In the MOF pores the flavin molecules are separated and the computed MIA@MOF structures do not find π-stacking interactions to the pore walls but only weak van-der-Waals contacts which reasons the enhanced fluorescence lifetime and quantum yield of the flavins in the composites compared to their neat solid state. The flexible MOF MIL-53(Al) was optimized essentially to the experimental large-pore form in the guest-free state with QuantumEspresso (QE) and with MIA molecules in the pores the structure contracted to close to the experimental narrow-pore form which was also confirmed by PXRD. In summary, the incorporation of flavins in MOFs yields solid-state materials with enhanced rigidity, stabilized conformation and reduced aggregations of the flavins, leading to increased fluorescence lifetime and quantum yield as controllable photo-luminescent and photo-physical properties.

This study describes all the properties of high T_c cuprates by introducing rotating holes that are created by angular momentum conservations on a 2D CuO₂ surface, and which have a different mass from that of a normal hole because of the magnetic field energy induced by the rotation. This new particle called a macroscopic Boson describes the doping dependences of pseudo-gap temperature and the transition temperature at which an anomaly metal phase appears and describes the origin of the pseudo-gap. Furthermore, this study introduces a new model to handle many-body interactions, which results in a new statistic equation. This statistic equation describing many-body interactions accurately explains why high T_c cuprates have significantly high critical temperatures. Moreover a partition function of macroscopic Bosons describes all the properties of anomaly metal phase, which sufficiently agree with experiments, using the result from our previous study [1] that analytically describes the doping dependence of T_c. By introducing a macroscopic Boson and the new statistical model for many-body interactions, this study uncovered the mystery of high T_c cuprates, which have been a challenge for many researchers. An important point is that, in this study, pure analytical calculations are consistently conducted, which agree with experimental data well (i.e., they do not use numerical calculations or fitting methods but use many actual physical constants).

Two solvated rhenium(IV) complexes with formula [ReCl4(bpym)]·MeCN (1) and [ReCl4(bpym)]·CH3COOH·H2O (2) [bpym = 2,2'-bipyrimidine] have been prepared and characterized by means of Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy and energy dispersive X-ray analysis (SEM–EDX), single-crystal X-ray diffraction (XRD) and SQUID magnetometer. 1 and 2 crystallize in the monoclinic system with space groups P21/n and P21/c, respectively. In both compounds, the Re(IV) ion is six-coordinate and bound to four chloride ions and two nitrogen atoms of a 2,2’-bipyrimidine molecule forming a distorted octahedral geometry around the metal ion. In the crystal packing of 1 and 2, intermolecular halogen⋯halogen and π⋯halogen type interactions are present. Hydrogen bonds take place only in the crystal structure of 2. Both compounds exhibit an akin crystal framework based on halogen bonds. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a similar magnetic behavior for both compounds, with antiferromagnetic exchange between the Re(IV) ions connected mainly through intermolecular Re-Cl···Cl-Re interactions.

Bismuth oxides are well-known electro-catalysts in fuel cells systems; they are usually used as anodic materials for the oxidation of low molecular weight alcohols. The utilization of BiO₂ and MnO₂ as catalysts in the pharmaceutical analysis is analytical method for the determination of heavy metal antibacterial agents in Pharmaceutical Dosage form is developed. The method is based on the voltammetric determination of heavy metal using Bidified platinum electrode by Bismuth oxide. The two components are oxidized at the Bidified electrode surface with the development of current that is linearly proportional to their concentrations in the range of 7.04*10^-7- 1*10^-3 M heavy metal. The oxidation reaction of the two components is pH-dependent, in which the buffer used is Britton-Robinson at pH = 7.00 where maximum peak current and maximum peak separation is obtained. The regression factors obtained from the calibration curves are 0.9812. The method of analysis was validated, where the limit of detection (LOD) and the limit of quantitation (LOQ) were calculated to be 1.44*10^-4 M, 4.36*10^-4 M and 1.27*10^-4 M, 3.84*10^-4 M respectively, the percentage recovery of both components was also calculated to 77 % for heavy metal.

Plazomicin is a recently U.S. Food and Drug Administration (FDA)-approved semisynthetic aminoglycoside. Its structure consists of a sisomicin scaffold modified by adding a 2(S)-hydroxy aminobutyryl group at the N1 position and a hydroxyethyl substituent at the 6′ position. These substitutions produced a molecule refractory to most aminoglycoside-modifying enzymes. The main enzyme within this group that recognizes plazomicin as substrate is the aminoglycoside 2′-N-acetyltransferase type Ia [AAC(2′)-Ia], which reduces the antibiotic’s potency. Designing formulations that combine an antimicrobial with an inhibitor of resistance is a recognized strategy to extend the useful life of existing antibiotics. We have recently found that several metal ions inhibit acetylation of numerous aminoglycosides catalyzed by the aminoglycoside 6′-N-acetyltransferase type Ib [AAC(6′)-Ib]. In particular, Ag1+, which also enhances the effect of aminoglycosides by other mechanisms, is very effective in interfering with AAC(6′)-Ib-mediated resistance to amikacin. Here we report that silver acetate is a potent inhibitor of AAC(2′)-Ia-mediated acetylation of plazomicin in vitro, and it reduces resistance levels of Escherichia coli carrying aac(2′)-Ia. The resistance reversion assays produced equivalent results when the structural gene was expressed under the control of the natural or the blaTEM-1 promoters. The antibiotic effect of plazomicin in combination with silver was bactericidal, and the mix did not show significant toxicity to human embryonic kidney 293 (HEK293) cells.

We have detected a large Nernst effect in the CDW state of the multiband organic metal α−(BEDT−TT)2KHg(SCN)4. We find that there exists a significant gradient of charge relaxation processes that can generate a sizeable contribution adding especially to the transverse thermoelectric signal. Apart from the phonon drag, the energy relaxation processes governing the electron-phonon interactions and the momentum relaxation processes governing the charge mobility of the q1D group of carriers have a significant role in observing the large Nernst signal in the CDW state. The emphasised momentum relaxation dynamics in the low field CDW state is a clear indicator of a significant carrier mobility that can lead to the largest Nernst signal in this state. The momentum relaxation is reduced with increasing angle and magnetic field, i.e., in the high field CDW state which is reflected in the smaller Nernst effect amplitude. In this case only the phonon drag and electron-phonon interactions are contributing to the transverse thermoelectric signal. Our findings advance and change the previous observations on the complex properties of this organic metal.

The need to regulate the non-exhaust particulate emissions from vehicles has been discussed worldwide due to the toxicity to the human body as well as the atmosphere. In-depth studies have been conducted on precise analysis of the non-exhaust particulates, in particular, accurate measurement of tire-brake-road wear particles, and their proportion in the atmosphere. In this study, the influence of tire and road wear particles (TRWP) on particulate matter (PM) in the atmosphere was investigated through tire and PM samples. PM samples were collected from the atmosphere using a high-volume sampler equipped with a quartz filter. Additionally, polycyclic aromatic hydrocarbons (PAHs) and heavy metals in tire rubber were analyzed as markers by pyrolysis-gas chromatography/mass spectrometry (GC/MS), GC/MS, and inductively coupled plasma/mass spectrometry (ICP/MS). More vinylcyclohexene was detected than dipentene in the markers measured in the samples of tires equipped with vehicles driving on the road with the high-volume sampler installed, while more dipentene was detected in total suspended particles (TSP) samples. Among the PAHs measured in tire samples, pyrene exhibited the highest concentration. In TSP samples, benzo(b)fluoranthene showed the highest concentration. Among the heavy metals, zinc exhibited the highest concentration in all tire samples and calcium in TSP samples.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

A formula for the turbulent Prandtl number is derived in terms of local variables available from two-equations turbulence models. The derivation is a direct consequence of the expected square additivity of the molecular and turbulent parameters defining the effective viscosity and the effective conductivity. The formula does not degenerate and leads to a Kays like formulation if approximated. Its utility and its limitation are discussed.

In spite of large-scale investigations of homogeneous single-site metallocene catalysts and systems based on them, the problem of controlling their activity, chemo- and stereoselectivity with the aim of developing efficient methods for the preparation of practically useful products of alkenes transformation, such as dimers, oligomers, and polymers, still remains topical. Here we studied catalytic activity of differently structured zirconocenes (10 examples of cyclopentadienyl and indenyl complexes) and co-catalysts activating the system, namely HAlBui2, MMAO-12 or (Ph3C)[B(C6F5)4] at low activator/Zr ratios in 1-hexene oligomerization reaction. The influence of catalyst structure and system composition on alkene conversion, type of products formed and reaction stereoselectivity was investigated. The composition of hydride intermediates forming in the systems L2ZrCl2 (L2= ansa-Me2CCp2)-HAlBui2-activator was studied by NMR and the participation of biszirconium hydride complex as the precursor of catalytically active sites of the alkene dimerization reaction was shown.

Oxidation reactions on semiconducting metal oxides (SMOs) surfaces have been extensively worked on in catalysis, fuel cells, and sensors. SMOs engaged powerfully in energy-related applications such as batteries, supercapacitors, solid oxide fuel cells (SOFCs), and chemical gas sensors. The deep understanding of SMO surface and oxygen interactions and defect engineering has become significant because all those mentioned applications are based on the adsorption/absorption and consumption/transportation of adsorbed (physisorbed-chemisorbed) oxygen. More understanding of adsorbed oxygen and oxygen vacancies (〖V_O^•,V〗_O^(••)) is needed, as the former is the vital requirement for sensing chemical reactions, while the latter facilitates the replenishment of adsorbed oxygen ions on the surface. We determined the relation between sensor response (sensitivity) and the amounts of adsorbed oxygen ions (O_(2(ads))^-,O_((ads),)^- O_2(ads)^(2-),O_((ads))^(2-)), water/hydroxide groups (H2O/OH^-), oxygen vacancies (〖V_O^•,V〗_O^(••)), and ordinary lattice oxygen ions (O_lattice^(2-)) as a function of temperature. During hydrogen (H2) testing, the different oxidation states (W6+, W5+, and W4+) of WO3 were quantified and correlated with oxygen vacancy formation (〖V_O^•,V〗_O^(••)). We used a combined application of XPS, UPS, XPEEM-LEEM, and chemical, electrical and sensory analysis for H2 sensing. We established a correlation between the H2 sensing mechanism of WO3, sensor signal magnitude, the amount of adsorbed oxygen ions, and sensor testing temperature. This paper also provides a review of the detection, quantification, and identification of different adsorbed oxygen species. The different surface and bulk-sensitive characterization techniques relevant to analyzing the SMOs-based sensor are tabulated, providing the sensor designer with the chemical, physical, and electronic information extracted from each technique.

Laser Powder Directed Energy Deposition (LP-DED) is an Additive Manufacturing process in which a laser beam is used to generate a melt pool onto a substrate. The additional material, in form of powder material, is fed into the generated melt pool and a raised track is obtained. The LP-DED process is very powerful for different applications such as the repair operations and the production of functionally graded material, however the application is still limited and one of the main reasons is related to the lack of knowledge in the physics of the process mechanisms. The process is influenced by a huge number of parameters and three main mechanisms can be identi-fied. These mechanisms are the powder flow, the generation of the molten pool and the solidifica-tion process and for each of these mechanisms the process parameters have a different relevance. In this paper, a review of the main mechanisms and the relationship between the process parame-ters and the outcome of each step of the process is presented.

Metal halide perovskites (MHPs), in particular lead-based halide perovskites have earned a recognized fame in several fields for their outstanding optoelectronics properties including direct generation of free charge carriers, optimal ambipolar charge carrier transport properties, high absorption coefficient, point-defect tolerance, and compositional versatility. Nowadays, this class of materials represents a real and promising alternative of silica for the photovoltaic technologies. This worthy success led to a growing interest in the exploration of MHP materials in other hot research fields such as the solar-driven photocatalytic water splitting towards hydrogen production, CO2 reduction to CO and CH4, useful organic reactions such as organic synthesis (formation of C-C, C-N, and C-O bonds), and pollutants and dye degradation. Nevertheless, many of these perovskite materials showed air and moisture instability problems that considerably hinder their practical application for photocatalytic water splitting and photodegradation of CO2. Moreover, if the chemical instability is a problem that can be in part mitigated by the optimization of the lattice structure, the presence of lead represents a real problem for the practical application of these type of materials in commercial devices. To successfully overcome this problem, lead-free metal halide perovskites (LFMHPs) have gained increasing interest thanks to their promising optoelectronic properties, comparable to lead-based materials, and their eco-friendly nature. Among all the lead-free perovskite alternatives, this mini review will focus the attention on the bismuth-based perovskites and perovskite derivatives with specific focus on solar-driven photocatalysis application for H2 evolution.

The electrochemical CO2 reduction reaction can lead to high value-added molecules production while helping decrease anthropogenic CO2 emissions. Copper can reduce CO2 to more than thirty different hydrocarbons and oxygenates, but it lacks the required selectivity. We present a computational investigation of the role of nano-structuring and alloying in Cu-based catalysts on the activity and selectivity of CO2 reduction to one-carbon products: carbon monoxide, formic acid, formaldehyde, methanol, and methane. The adsorption, activation, and conversion of CO2 were computed on monometallic and bimetallic (decorated and core-shell) 55-atom Cu-based clusters. The dopant metals considered were Ag, Cd, Pd, Pt, and Zn, located at different coordination sites. The relative binding strength of the intermediates at different applied potentials were used to identify the optimal catalyst for the selective CO2 conversion to one carbon products. It was discovered that single atom doping with Cd and Zn is optimal for the CO2 to carbon monoxide conversion. The core-shell models with Ag, Pd, and Pt provided higher selectivity for formic acid and formaldehyde. The Cu-Pt and Cu-Pd showed lowest overpotential for methane formation.

Organophosphorus nerve agents are amongst the most toxic chemicals known to human beings. 9 They interfere with the central nervous system, resulting in continuous muscle contractions, 10 paralysis and even death. Prohibition by many countries around the world cannot disguise the 11 remaining presence of nerve agents in stockpile storage and governmental deployment, 12 highlighting the dire need for an efficient catalyst to degrade and detoxify nerve agents by 13 hydrolysis. Metal-organic frameworks (MOFs) have raised a few eyebrows for their permanent 14 porosity, precise tunability, and lasting stability. Modern Reticular Chemistry fosters the design and 15 synthesis of well-defined crystalline MOFs with open Lewis acidic metal sites that can catalytically 16 hydrolyze nerve agents both in aqueous solution and in solid state systems, unveiling unparalleled 17 potential for MOF-based personal protection gears. In this review, a summary of the representative 18 catalytically active MOFs in nerve agent hydrolysis is discussed. MOFs are categorized by their 19 reticular structure, emphasizing the capability and mechanistic insights of each single MOF in nerve 20 agent hydrolysis. The author’s perspective on the current challenges and future directions of MOF- 21 based catalysts in real-world protection applications is also provided, which hopefully could shed some 22 light on the future development of commercially available MOF protection suits.

Within this work we review the metal coordination effect on the photophysics of metal dipyrrinato complexes. Dipyrrinato complexes are promising candidates in the search for alternative transition metal photosensitizers for application in photodynamic therapy (PDT). These complexes can be activated by irradiation with light of a specific wavelength, after which cytotoxic reactive oxygen species (ROS) are generated. The metal coordination allows for the use of the heavy atom effect, which can enhance the triplet generation necessary for generation of ROS. Additionally, the flexibility of these complexes for metal ions, substitutions and ligands allows the possibility to tune their photophysical properties. A general overview of the mechanism of photodynamic therapy and the properties of the triplet photosensitizers is given, followed by further details of dipyrrinato complexes described in the literature that show relevance as photosensitizers for PDT. In particular, the photophysical properties of Re(I), Ru(II), Ir(III), Ni(II), Cu(II), Pd(II), Pt(II), Zn(II), Ga(III), In(III), Al(III), Sn(II), and P dipyrrinato complexes are discussed. The potential for future development in the field of (dipyrrinato)metal complexes is addressed and several new research topics are suggested throughout this work. We propose that significant advances could be made for heteroleptic bis(dipyrrinato)zinc(II) and homoleptic bis(dipyrrinato)palladium(II) complexes and their application as photosensitizers for PDT.

Residual stresses in fiber metal laminates (FML) inevitably develop during the manufacturing process. The main contributor to these stresses is the difference in the coefficients of thermal expansion (CTE) between fibers and metal in combination with high process temperatures. To quantify these stresses, the use of specimens with an asymmetric layup is an easily adaptable method. The curvature that develops after the manufacturing of flat laminates with an asymmetrical layer stack is a measure of the level of residual stresses evolving during cure. However, the accuracy of the curvature evaluation is highly dependent on specimen design and other influencing parameters. In this work a large set of FML specimens is investigated to identify relevant influencing parameters and derive conclusions about specimen design and evaluation techniques. For certain layups and process parameters, there is a good correlation between the curvature and the stress-free temperature, which is further covered by analytical solutions for bimetals. This correlation is the basis to transfer curvature into a stress-free temperature that can consequently be used for the quantification of residual stress levels in more complex FMLs. The transfer is validated by in-situ strain measurements during cure using a strain gage technique. Based on the results, the application of asymmetric specimens for residual stress characterization in more complex laminates is presented in the form of a workflow.

By drilling periodic thru-holes in a suspended film, the phonon system can be modified. Being motivated by the BCS theory, the technique, so-called phonon engineering, was applied to a niobium sheet. The newly emergent high-T_c superconductivity, however, cannot be accounted for by the BCS theory. Rather, its exposed configuration, namely a square-lattice oxygen network, is reminiscent of the copper--oxygen plane in cuprate high-T_c superconductors. It turns out that its magnetic result is consistent with the principle of giant atom, which was developed by another heroes of superconductivity, Fritz London and John Slater, in the 1930s, several decades earlier than the propagation of BCS theory. The superconducting transition feature is discussed on the basis of a comprehensive theory of the giant atom---the theory of hole superconductivity.

The integration of metal nanoparticles and solid carriers can achieve ideal stability, high load and good conductivity. In this work, copper nanoparticles (Cu NPs) were sequentially deposited on a cobalt metal-organic framework (Co-MOF) by bonding with exposed imino groups, followed by a reduction reaction to prepare a new Cu@Co-MOF composite. Cu@Co-MOF acts as a non-enzymatic electrochemical sensor to detect glucose (Glu) in an alkaline medium. The composite working electrode of Cu@Co-MOF/GCE (GCE = glassy carbon electrode) improves the electrocatalytic activity for Glu oxidation. Cu@Co-MOF/GCE shows excellent electrocatalytic performances in Glu concentration ranging 0.005~1.8 mmol∙L⁻¹ (mM): the sensitivities are 282.89 μA∙mM⁻¹∙cm⁻² in 0.005-0.4 mM Glu and 113.15 μA∙mM⁻¹∙cm⁻² in 0.4-1.8 mM Glu respectively with low detection limit of 1.6 μM (S/N = 3) and high selectivity and stability.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

We studied surface enhanced Raman spectra of amino acids D-alanine and DL-serine and their mixture on silver nanoisland films (SNF), immersed in phosphate buffer saline solution at millimolar amino acid concentrations. It is shown that the spectra from the amino acid solutions differ from the reference spectra for microcrystallites due to electrostatic orientation of amino acid zwitterions by the metal nanoisland film. Moreover, non-additive peaks are observed in the spectrum of the mixture of amino acids adsorbed on SNF, which means that intermolecular interactions between adsorbed amino acids are very significant. The results indicate the need for a thorough analysis of the Raman spectra from amino acid solutions in the presence of a nanostructured metal surface, and may also be of interest for studying molecular properties and intermolecular interactions.

All living organisms require some metal ions for their energy production as well as metabolic and biosynthetic processes. Within cells, metal ions are involved in the formation of adducts interact with metabolites and macromolecules (proteins and nucleic acids). The proteins that require binding to one or more metal ions to be able to carry out their physiological function are called metalloproteins. About one third of all protein structures in the Protein Data Bank involve metalloproteins. Over the past few years there has been a tremendous progress in the number of computational tools and techniques making use of 3D structural information to support the investigation of metalloproteins. This trend has been boosted also by the successful applications of neural networks and deep learning approaches in molecular and structural biology at large. In this review, we discuss recent advances in the development and availability of resources dealing with metalloproteins from a structure-based perspective. We start by addressing tools for the prediction of metal-binding sites (MBSs) using structural information on apo-proteins. Then, we provide an overview of methods for and lessons learned from the structural comparison of MBSs in a fold-independent manner. We then move to describing databases of metalloprotein/MBS structures. Finally, we summarize recent DL applications enhancing the functional interpretation of metalloprotein structures.

Structural health monitoring of lightweight constructions made of composite materials can be performed using guided ultrasonic waves. If modern fiber metal laminates are used, this requires integrated sensors that can record the inner displacement oscillations caused by the propagating guided ultrasonic waves. Therefore, we have developed a robust MEMS vibrometer that can be integrated with structural and functional compliance. This vibrometer is directly sensitive to the high-frequency displacements from structure-borne ultrasound when excited between its first and second natural frequency. The vibrometer is mostly realized by processes earlier developed for a pressure sensor but with additional femtosecond laser ablation and wafer bonding. The piezoresistive transducer made from silicon is encapsulated between top and bottom glass lids. The natural frequencies are experimentally determined using an optical micro vibrometer setup. The vibrometer functionality and usability for structural health monitoring are demonstrated on a customized test rig by recording application-relevant guided ultrasonic wave packages with a central frequency of 100 kHz at a distance of 200 mm from the exciting ultrasound transducer.

Guided ultrasonic waves are suitable for use in the context of structural health monitoring of thin-walled, plate-like structures. Hence, observing the wave propagation in the plates can provide an indication of whether damage has occurred in the structure. In this work, the wave propagation in fiber metal laminate consisting of thin steel foils and layers of carbon fiber-reinforced polymer is studied, focusing on the main propagation characteristics like dispersion diagrams and displacement fields. For this purpose, the dispersion diagrams derived from the analytical framework and numerical simulations are first determined and compared to each other. Next, the displacement fields are computed using the global matrix method for two excitation frequencies. The results derived from the analytical framework is used to validate numerically determined displacement fields based on a 2D and a 3D modeling approach. For both investigations the results of the analytical treatment and the numerical simulation show good agreement. Furthermore, the displacement field reveals the typical and well-known characteristics of the propagation of guided waves in thin-walled structures. Since the use of full 3D models involves a very high computational cost, this work also successfully investigates the possibility for model order reduction to decrease the computational time and costs of the simulation without the loss of accuracy.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

As one of the representatives of emerging metallic transition metal dichalcogenides, niobium ditelluride (NbTe₂) has attracted intensive interest recently due to its distorted lattice structure and unique physical properties. Here, we report on the ultrafast carrier dynamics in NbTe₂ measured using time-resolved pump-probe transient reflection spectroscopy. A thickness-dependent carrier relaxation time is observed, exhibiting a clear increase in the fast and slow carrier decay rates for thin NbTe₂ flakes. In addition, pump power dependent measurements indicate that the carrier relaxation rates are power-independent, with the peak amplitude of the transient reflectivity increasing linearly with pump power. Isotropic relaxation dynamics in NbTe₂ is also verified by performing polarization-resolved pump-probe measurements. These results provide an insight into the light-matter interactions and charge carrier dynamics in NbTe₂ and will pave the way for its applications to photonic and optoelectronic devices.

The application of metal-matrix composite coatings for protecting and improving the service life of sliding components has demonstrated to have the potentials of meeting the requirements of a diverse range of engineering industries. Recently, a significant body of research has been devoted to study the mechanical and tribological performance of dispersion-strengthened MCrAlY coatings. These coatings belong to a class of emerging wear-resistant materials, offering improved properties and being considered as promising candidates for the protection of engineering structural materials exposed to tribological damage, especially at elevated temperature regimes. This paper attempts to comprehensively review the different reinforcements used in the processing of MCrAlY-based alloys and how they influence the mechanical and tribological properties of the corresponding coatings. Further, the major fabrication techniques together with their benefits and challenges are also reviewed. Discussion on the failure mechanisms of these coatings as well as the main determining factors are also included. In addition, a comprehensive survey of studies and investigations in recent times are summarized and elaborated to further substantiate the review.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

Using two metal insulated metal waveguides (MIM) and five resonator (a quadrilateral cavity and three rings with different dimensions), we design a plasmonic refractive index sensor. Using the time domain finite difference method, we examine and analyze the sensor performance (numerical analysis) and using the transmission line model method, we theoretically examine the performance of the sensor By summarizing these two methods and calculating the sensitivity coefficient S, quality coefficient Q and figure of merit (FOM), a plasmonic sensor with good performance is obtained. Using the supermods of the resonators, we will achieve a stable wavelength spectrum and a suitable and stable sensitivity coefficient spectrum. Challenges and changes that occur in different modes of this sensor will lead to a balanced and relatively good structure. This designed sensor can be useful in the development of integrated optical circuits.

In this paper, a plasmonic refractive index sensor based on metal insulated metal waveguide (MIM) with three rings and a resonant cavity is first proposed and numerically evaluated. Next, we add four teeth to the sensor structure. We study and simulate the resonant wavelengths and refractive index of resonators using the time difference finite difference method. Given that the sensor and the conduction characteristics of plasmonic waves are influenced by the structure parameters,Therefore, by changing the refractive index and changing the dimensions and coordinates of the cavity and rims, we can change the passage coefficient in the resonant modes and measure the sensor performance. As a result, we obtain the sensitivity coefficient, the figure of merit (FOM) and the quality factor Q of the sensor. We modulate the resonance wavelength FWHM using the generated modes and reach a sensitivity of 2166 nm / RIU. These plasmonic sensors with a simple framework and balanced performance and high optical resolution can be used to measure the refractive index in the medical, chemical and food industries.

The detection of Dark Matter is the greatest outstanding problem in modern cosmology. Several attempts have been taken for this without any remarkable success. To find out a suitable way of detection we need to understand its nature comprehensively. In the present article, a hypothesis is described considering Dark Matter as a normal matter. Its peculiar behavior is explained considering its existence in BEC state in the coolest part of the universe that makes it an electromagnetic insulator. Depending upon this hypothesis an experimental verification method is proposed.

Volcanic fumaroles are openings in the earth's surface, where volcanic gases discharge to the atmosphere. Metallic and non-metallic elements contained in gases form specific mineral precipitates upon cooling. Although the presence of metals in fumarolic gases has long been known, their concentrations are generally low and difficult to measure directly. A laboratory model of a fumarole may resolve the situation if the complex gas composition could be accurately reproduced. Here we describe a new experimental approach that allows accurately simulating fumarolic gases in terms of their main components (H₂O, CO₂, S, HCl), as well as adding volatile metal compounds. Gas is generated inside a special flow-through reactor, at the outlet of which the elements contained in the gas form temperature-dependent mineral sequence inside the attached silica-glass tube. Using this installation, we obtained laboratory sublimates from reducing (H₂S-rich) gases similar to natural ones in terms of mineral composition and mineral habits. Twenty-one phases have been identified in sublimates, among which are simple and complex chlorides, simple sulfides and six sulfosalts. Comparison of the sublimate deposition from H₂O-rich gas at 1 bar with similar works performed in evacuated ampoules at low pressure showed that fumarolic gases behave like an ideal gas, in which molecules do not interact with each other, and reactive compounds in the gas serve in fact as an inert carrier of volatile metals species. Changing the composition of the gas at the outlet of the installation, its flow rate and temperature, we can observe the corresponding changes in mineral precipitates and in such a way study the factors affecting mineral formation on natural fumarolic fields.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

Radially polymerized dendritic compounds are nowadays an established polymer category next to their linear, branched and cross-linked counterparts. Their uncommon tree-like architecture is characterized by adjustable internal cavities and external groups. They are therefore exceptional absorbents and this attainment of high concentrations into their interior renders them ideal reac-tion media. In this framework they are applied in many environmentally benign implementa-tions. One of the most important among them is water purification though pollutant decomposi-tion. Simple and composite catalysts and photo-catalysts containing dendritic polymers and ap-plied in water remediation will be discussed jointly with some unconventional solutions and fu-ture prospects.

Over the centuries, honey is known for its superior usage in culinary, and for its rich nutrition and therapeutic values which are scientifically proven in the medical field. The chemical composition of honey varies depending on its botanical sources and environment. Therefore, the nutrition content in honey is highly likely to be affected by contaminants, such as heavy metals and pesticides. To ensure the quality of honey, parameters such as the heavy metal content should be within the safe range of total standard mineral and trace elements as defined by the International Food Standard (Codex Alimentarius), and pesticides should not be present at all. The high concentration of heavy metal and pesticides not only deteriorates the quality and quantity of honey, but also causes harm to the bee colony itself. In the agriculture sector, the excessive usage of pesticides and fertilizer negatively impacts the overall honey production process. Bees, a pollinating agent, bring the polluted nectar back to their beehives, eventually contaminating the honey and depreciating its value. Hence, this article will comprehensively review the activities that contribute to heavy metal and pesticide contamination, the interactions of bees as a pollinating agent, the impact of the pollutant to the colonies, and subsequently to the honey production.

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex > organic-matter–clay mineral complex > iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

We report a prebiotically relevant solution to the N1-ribosylation of pyrimidine nucleobases, a well-known challenge in the RNA World hypothesis. It is found that the presence of metal cations and clay mineral enables the previously unachievable direct ribosylation of uracil, providing by far the highest yield. Spectroscopy and chromatography analyses confirmed the formation of ribosylated uracil. The method can also be extended to the ribosylation of 2-pyrimidinone. These findings are also compatible with the metal-doped-clay model developed by our lab for the unified route of the selection of ribose and subsequent syntheses of nucleotide and RNA.

In this study, we seek to analyze and numerically evaluate a plasmonic sensor. To form the sensor structure, we use several amplifiers, such as two rings attached to each other and a cavity, as well as two metal insulating metal waveguides (MIM). At the beginning of this simulation, we must examine the resonant wavelengths and the refractive index of the resonators using the finite difference time domain method. By changing the refractive index and changing the dimensions of the cavity and the rims, we seek to investigate the sensor performance and the conduction characteristics of the plasmonics and to obtain the effect of these parameters. To evaluate the sensor performance, we calculate the three factors of sensitivity coefficient S, quality factor Q and figure of merit (FOM), here we reach the sensitivity of 987.6 nm / RIU. Such a plasmonic sensor with a simple framework and high optical resolution can be very useful for sensor systems on optical circuits.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

With this article, impact of effluent mixed water with the quality of the Mansagar Lake has been established by evaluating the physico-chemical parameters and the heavy-metal contents experimentally. The process of calculating water quality and the metal pollution quality indices is also explained in brief with respect to selected sample locations and varied environmental conditions (Pre- and Post-Monsoon season). Distribution trends of Pearson‘s correlation factor have also been discussed to establish their relation among the physico-chemical parameters and the heavy-metal contents for varied environmental conditions. In the end, detailed discussion on observations made during this study and useful recommendations are also elaborated in details. With this article, we intend to present a document for better understanding of the water quality of this lake in view of futuristic management strategies to be adopted to maintain it heritage values.

Metal/metal composites represent a particular class of materials showing innovative mechanical and electrical properties. Conventionally, such materials are produced by severely plastically deforming two ductile phases via rolling or extruding, swaging, and wire drawing. This study presents the feasibility of producing metal/metal composites via a capacitive discharge-assisted sintering process named electro-sinter-forging. Two different metal/metal composites with CP-Ti/AlSi10Mg ratios (20/80 and 80/20 %vol) are evaluated, and the effects of the starting compositions on the microstructural and compositional properties of the materials are presented. Bi-phasic metal/metal composites constituted by isolated α-Ti and AlSi10Mg domains with a microhardness of 113 ± 13 HV_0.025 for the Ti20-AlSi and 244 ± 35 HV_0.025 for the Ti80-AlSi are produced. The effect of the applied current is crucial to obtain high theoretical density, but too high currents may result in Ti dissolution in the Ti80-AlSi composite. Massive phase transformations due to the formation of AlTiSi based intermetallic compounds are observed through thermal analysis and confirmed by morphological and compositional observation. Finally, a possible explanation for the mechanisms regulating densification is proposed accounting for current and pressure synergistic effects.

Three-Dimensional mesoporous TiO2 scaffolds of anatase phase possess inherent eximious optical behavior that are beneficial in designing photoelectrodes for solar energy conversion applications. However, substantial efforts have been devoted in maximizing the UV and/or visible light absorption efficiency, and suppressing the annihilation of photogenerated charged species in pristine mesoporous TiO2 structure for improved solar illumination conversion efficiencies. This study provides the fundamental insights into Mxene functionalized mesoporous TiO2 as photoelectrode for the first time. This novel combination of Mxene functionalized TiO2 electrodes with and without TiCl4 treatments have been successfully optimized to intensify the process of photon absorption, charge segregation and photocurrent, resulting in superior photoelectrode performance. The photocurrent measurements of prepared photoelectrodes are significantly enhanced upon increased contents of Mxene due to improved absorption efficiency within the visible region as verified by UV–Vis absorption spectroscopy. Moreover, as evident through structural analysis, the anatase phase of TiO2 is well grown due to increased contents of Mxene and post-deposition heat treatments. Consequently, an appreciable coverage of well-developed grains on FTO surface observed in SEM images. Thereby, the newly fabricated conductive mesoporous TiO2 photoelectrodes are potential candidates for photoinduced energy conversion and storage purposes.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

This paper focuses on parametric model order reduction (PMOR) of guided ultrasonic wave propagation and its interaction with damage in a fiber metal laminate (FML). Structural health monitoring in FML seeks to detect, localize and characterize the damage with high accuracy and minimal use of sensors. This can be achieved by the inverse problem analysis approach which employs the signal measurement data recorded by the embedded sensors in the structure. The inverse analysis requires to solve the forward simulation of the underlying system several thousand times. These simulations are often exorbitantly expensive and triggered the need for improving their computational efficiency. A PMOR approach hinged on the proper orthogonal decomposition method is presented in this paper. An adaptive parameter sampling technique is established with the aid of a surrogate model to efficiently update the reduced-order basis in a greedy fashion. A numerical experiment is conducted to illustrate the parametric training of the reduced-order model. The results show that the reduced-order solution based on the PMOR approach is accurately complying with that of the high fidelity solution.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

In the design and development of novel materials that have excellent mechanical properties, classification and regression methods have been diversely used across mechanical deformation simulations or experiments. The use of materials informatics methods on large data that originate in experiments or/and multiscale modeling simulations may accelerate materials discovery or develop new understanding of materials’ behavior. In this fast-growing field, we focus on reviewing advances at the intersection of data science with mechanical deformation simulations and experiments, with a particular focus on studies of metals and alloys. We discuss examples of applications, as well as identify challenges and prospects.

Heavy metal contaminants have serious consequences for the environment and human health. Consequently, effective methods for detecting their presence, particularly in water and food, are urgently required. Accordingly, the present study proposes a sensor for the detection of mercury Hg(II) and lead Pb(II) ions using graphene oxide (GO) as a quenching agent and aptamer solu-tion as a reagent. In the proposed device, the aptamer sequences are labeled by FAM and HEX fluorescent dyes, respectively, and are mixed with 500 ppm GO solution in a microfluidic device. The presence of Hg(II) and Pb(II) ions is then detected by measuring the change in the fluores-cence intensity of the GO/aptamer suspension as the aptamer molecules undergo fluorescence resonance energy transfer (FRET). The experimental results show that the aptamer sensors have a linear range of 10~250 nM (i.e., 2.0~50 ppb) for Hg(II) ions and 10~100 nM (i.e., 2.1~20.7 ppb) for Pb(II) ions. Furthermore, the limit of detection is around 2 ppb for both metals, which is signifi-cantly lower than the maximum limits of 6 ppb and 10 ppb prescribed by the World Health Or-ganization (WHO) for Hg(II) and Pb(II) in drinking water, respectively.

The outdoor sculpture of the first Portuguese king, D. Afonso Henriques (~1109 – 1185 AD), placed in Guimarães (North Portugal) is one of the most emblematic national sculptures. Created in 1887 by António Soares dos Reis, it possesses a remarkable symbolic value in the presumed birthplace of the king. In addition to the artistic and heritage importance of the monument, it is one of the few sculptures cast by a Portuguese industrial foundry in the 19th-century. This study obtained data on the sculpture's elemental composition and corrosion products, gathering important historical and technical information. For this purpose, a multi-analytical approach consisting of X-ray fluorescence (XRF), X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM-EDS) was carried out to characterise the bulk metal and corrosion layers. The data revealed a ternary alloy of Cu, Sn, Zn with Pb, Fe, As, Bi and Mn as minor elements. The alloy matches that of other sculptures cast in that period. In terms of corrosion, it is characterised by the presence of oxides. These results represent the first step for applying an appropriate conservation strategy for bronze sculptures with similar characteristics.

Description of redox reactions is critically important for understanding and rational design of materials for electrochemical technologies including metal-ion batteries, catalytic surfaces, or redox-flow cells. Most of these technologies utilize redox-active transition metal compounds due to their rich chemistry and their beneficial physical and chemical properties for these types of applications. A century since its introduction, the concept of formal oxidation states (FOS) is still widely used for rationalization of the mechanisms of redox reactions, but there exists a well-documented discrepancy between FOS and the electron density-derived charge states of transition metal ions in their bulk and molecular compounds. We summarize our findings and those of others which suggest that density-driven descriptors are in certain cases better suited to characterize the mechanism of redox reactions, especially when anion redox is involved, which is the blind spot of the FOS ansatz.

The Katangese Copperbelt area (KCA) located south-eastern of D.R. Congo presents high concentration of metal trace elements (MTE) in several soils due to a rich natural geochemical background, and intense mining activities, causing serious health issues to humans and animals. However, the lack of data on specific baseline concentrations makes it difficult to properly assess and monitor the environmental quality of soils in the region. In this study, the baseline concentration of 11 potentially toxic MTE (i.e., Mn, Zn, Cu, Co, Cr, Pb, Cd, Ti, Ni, Al, and Fe) was assessed in topsoils of the KCA, and the possible influence of land uses (croplands, forest and mining areas) was examined. Results showed the following baseline concentrations, i.e. lower and upper limits (mg.kg^-1) in cropland soils : Al (18.4–162.0), Cd (0.0–0.1), Co (0.1–3.5), Cu (0.8–17.7), Cr (0.0–0.2), Fe (4.7–233.8), Mn (3.5–575.6), Ni (0.1–1.9), Pb (0.2–2.4), Zn (0.1–20.3), Ti (0.0–392.6); in forests: Al (18.8–1167.1), Cd (0.02–0.48), Co (0.20–18.1), Cu (3.6–42.7), Cr (0.1–33.7), Fe (86.4–283.3), Mn (4.9–1538.9), Ni (0.05–24.2), Pb (0.3–13.7), Zn (2.0–7.0), Ti (0.2–0.8); and in mining areas: Al (7.4–241.2), Cd (0.01–164.8), Co (0.2–211.3), Cu (2.4–5485.4), Cr (0.03–0.4), Fe (5.9–481.6), Mn (7.1–95.9), Ni (0.1–1.9), Pb (0.2–390.8), Zn (1.5–5629.3), Ti (0.1–1.3). Cu and Zn were highest in mining areas demonstrating a prevalent influence of mining activities in altering the natural background of metals concentrations in the region. By contrast, croplands and forest shared a similar trend of Al and Mn contents, suggesting a mild influence of agricultural activity. Intriguingly, higher Cu and Co contents were found in forest compared to croplands. For all the three studied land uses, no straightforward relation was found between metal concentrations and soil total acidity. This study is the first attempt to establish reference values of MTE contents in the KCA soils and thus provides valuable information for legislative purposes and for soil quality assessment.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

The screening and treatment of acid mine drainage (AMD) using Na₂FeO₄ has been explored. Elemental composition was performed using an ICP-OES for the raw and treated AMD. The AMD samples were collected from three different sampling sites (RTW1, RTW2 and RTW3) in Pretoria, South Africa with acidic pH ranging between 2.50 and 3.13. Total dissolved solids and Electrical Conductivity of AMD samples ranged between 960 and > 1000 mg. L^-1, 226 and 263 µS. cm^-1, respectively. The final pH of treated water samples increased up to ≥ 9.5 after treatment with Na₂FeO₄. Sodium ferrate showed dual functions by removing metals and raising the pH of the treated water. Concentrations of most trace elements were not complying with WHO and DWAF guideline standards in raw AMD while after treatment with Na₂FeO₄ the concentrations were below guidelines for domestic and irrigation purposes.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

For the better part of a century researchers across disciplines have sought to explain the crystallography of the elemental transition metals: hexagonal close packed, body centered cubic, and face centered cubic in a form similar to that used to rationalize the structure of organic molecules and inorganic complexes. Pauling himself tried with limited success to address the origins of transition metal stability. These early investigators were handicapped, however, by incomplete knowledge regarding the structure of metallic charge density. Here we exploit modern approaches to charge analysis to first comprehensively describe transition metal charge density. Then, we use topological partitioning and quantum mechanically rigorous treatments of kinetic energy to account for the structure of the density as arising from the interactions between metallic tetrahedra. We argue that the crystallography of the early transition metals results from charge transfer from the so called “octahedral” to “tetrahedral holes” while the face centered cubic structure of the late transition metals is a consequence of antibonding interactions that increase octahedral hole kinetic energy.

It is known that the elastic characteristics of polyamides change with increasing temperature, in particular, the Young's modulus decreases significantly. This fact is practically not taken into account in design calculations of metal-polymer plain (MP) bearings, operating under conditions of the boundary and dry friction. The purpose of the study is the analysis of the effect of temperature on the change of the Young's modulus and, accordingly, the contact strength and triboresource according to the developed method of calculating MP bearings. MP bearings with a bushing made of polyamide PA6 reinforced with glass or carbon dispersed fibers were investi-gated. Quantitative and qualitative regularities of change of the maximum contact pressures and resource of the bearings at temperature increase under conditions of boundary and dry friction are established. The pressures in the bearing bushing made of PA6+30GF will be lower than for the bushing made of PA6+30CF. The resource of the bushing made of PA6+30CF will be significantly greater than for PA6+30GF. For thermoplastic polymers, the increase in temperature will have a useful practical effect due to the decrease in the rigidity of the polymer composites of the bearing bushing.

Alzheimer’s disease (AD) is one of the most prevailing neurodegenerative diseases, characterized by memory dysfunction and the presence of hyperphosphorylated tau and amyloid β (Aβ) aggregate in multiple brain regions, including the hippocampus and cortex. The exact etiology of AD has not yet been confirmed. However, epidemiological reports suggest that populations who were exposed to environmental hazards are more likely to develop AD than those who were not. Arsenic (As) is a naturally occurring environmental risk factor abundant in the Earth’s crust and human exposure to As predominantly occurs through drinking water. Convincing evidence suggests that As causes neurotoxicity and impairs memory and cognition although the hypothesis and molecular mechanism of As-associated pathobiology in AD are not clear yet. However, exposure to As and its metabolites leads to various pathogenic events such as oxidative stress, inflammation, mitochondrial dysfunctions, ER stress, apoptosis, impaired protein homeostasis, and abnormal calcium signaling. Evidence has indicated that As exposure induces alterations that coincide with most of the biochemical, pathological, and clinical developments of AD. Here, we overview existing literature to gain insights into the plausible mechanisms that underlie As-induced neurotoxicity and the subsequent neurological deficits in AD. Prospective strategies for the prevention and management of arsenic exposure and neurotoxicity have also been discussed.

The electromagnetic inference is an issue from decades, where working for a better shielding material is still on-going. The purpose of this study is to review the existing methods in the formation of graphene, metal and polymer-based composites. Study indicates that in graphene and metal-based composites, the utilization of alternating deposition method showed the highest shielding effectiveness, whereas, in polymer-based composite, the utilization of chemical vapor deposition method showed highest shielding effectiveness. However, this review reveals that still there is a gap in the literature in terms of the selection of the method. Although there are various available methods which researchers adopt as per their convenience, none of the studies makes a comparison of the methods to form a similar composite. Therefore, as a future gap researcher needs to adopt various methods to form a single composite and then make a comparison of shielding effectiveness. This act will be useful for future researchers to select the appropriate method.

Highly-correlated electrons – electrons that engage in strong electron-electron interactions – have been observed in transition metal oxides and quantum dots and can create unusual material behavior that is difficult to model, such as switching between a low resistance metal state and a high resistance Mott insulator state. Tests of devices using a layer-by-layer deposition process for forming multilayer arrays of ferritin (a transition metal (iron) oxide storage protein) have been previously reported that indicate that highly-correlated electron transport is occurring, consistent with models of electron transport in quantum dots. This paper reports the results of the effect of various degrees of structural homogeneity on the electrical characteristics of these ferritin arrays, as well as demonstrating that these structures can provide a switching function associated with the circuit that they are contained within, consistent with the observed behavior of highly-correlated electrons.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

This paper aims at addressing the exploitation of solid-state carriers for hydrogen storage, with attention paid both to the technical aspects, through a wide review of the available integrated systems, and to the social aspects, through a preliminary overview of the connected impacts from a gender perspective. As for the technical perspective, carriers to be used for solid-state hydrogen storage for various applications can be classified into two classes: metal and complex hydrides. Related crystal structures and corresponding hydrogen sorption properties are reviewed and discussed. Fundamentals of thermodynamics of hydrogen sorption evidences the key role of the enthalpy of reaction, which determines the operating conditions (i.e. temperatures and pressures). In addition, it rules the heat to be removed from the tank during hydrogen absorption and to be delivered to the tank during hydrogen desorption. Suitable values for the enthalpy of hydrogen sorption reaction for operating conditions close to ambient (i.e. room temperature and 1-10 bar of hydrogen) are close to 30 kJ·molH2 1. The kinetics of hydrogen sorption reaction is strongly related to the microstructure and to the morphology (i.e. loose powder or pellets) of the carriers. Usually, kinetics of hydrogen sorption reaction is rather fast, and the thermal management of the tank is the rate determining step of the processes. As for the social perspective, various scenarios for the applications in different socio-economic contexts of solid-state hydrogen storage technologies are described. As it occurs with the exploitation of other renewables innovative technologies, a wide consideration of the social factors connected to these processes is needed to assess the extent to which a specific innovation might produce positive or negative impacts in the recipient socio-economic system and to explore the potential role of the social components and dynamics in fostering the diffusion of the innovation itself. Attention has been addressed to the gender perspective, in view of the enhancement of hydrogen-related energy storage systems, intended both in terms of the role of women in triggering the exploitation of hydrogen-based storage as well as to the impact of this innovation in their current conditions, at work and in daily life.

To date, theoretical analyses have provided several useful methods/algorithms for studying transition states and non-covalent interactions. Potential Energy Scan (PES) is one such method that has found wide application in the physicochemical community. Analyzing the PES profiles of the catalytic system of FeBr3 in Electrophilic Aromatic Substitution (EAS) with molecular halogens, one can notice an obvious difference from the modern textbook mechanisms proposed in this area of study. Moreover, the newly presented Graphic Methodology (GM) allows a simple and reliable transition state determination even for very weakly bound charge transfer complexes using second-order derivatives as an efficient tool in the graphical analysis. Relative errors that can be reduced to a few parts per thousand in transition state estimation make this method a potentially very useful tool in further graphical studies of non-covalent interactions. Studies performed using high-precision semiempirical methods suggest that the process of halonium ion quenching proceeds along a completely different pathway, suggesting a possible novel transition metal-nonmetal catalytic system involved in the EAS electrophilic quenching step. The results presented here strongly suggest a future GM application that is widely used and the introduction of pseudo and pre-transition states as new terms in the description of non-covalent interactions.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Herein, a novel cavity design of racetrack integrated circular cavity established on metal-insulator-metal (MIM) waveguide is suggested for refractive index sensing application. Over the past few years, we have witnessed several unique cavity designs to improve the sensing performance of the plasmonic sensors created on the MIM waveguide. The optimized cavity design can provide the best sensing performance. In this work, we have numerically analyzed the device design by utilizing the finite element method (FEM). The small variations in the geometric parameter of the device can bring a significant shift in the sensitivity and FOM of the device. The best sensitivity and FOM of the anticipated device are 1400 nm/RIU and ~12.01, respectively. We believe that the sensor design analyzed in this work can be utilized in the on-chip detection of biochemical analytes.

The response of a single tin oxide nanowire was collected at different temperatures to create a virtual array of sensors working as a nano-electronic nose. The single nanowire, acting as a chemiresistor, was first tested with pure ammonia and then used to determine the freshness status of trout fish (Oncorhynchus mykiss) in a rapid and non-invasive way. The gas sensor reacts to total volatile basic nitrogen, detecting the freshness status of the fish samples in less than 30 seconds. The sensor response at different temperatures correlates well with the total viable count (TVC), demonstrating that it is a good (albeit indirect) way of measuring the bacterial population in the sample. The nano-electronic nose is able to classify the samples according to their degree of freshness, but also to quantitatively estimate the concentration of microorganisms present. The system was tested with samples stored at different temperatures, managing to classify them perfectly (100%) and estimating their log(TVC) with an error lower than 5%.

Particle layers employing conductive transition metal nitrides have been proposed as possible alternative plasmonic materials for photovoltaic applications due to their reduced losses compared to metal nanostructures. We critically compare the photocurrent gain due to an additional layer made of nanopillars of nitrides with other material classes obtained in an already highly optimized doped c-Si baseline solar cell with accurate doping profile from measurements. A relative photocurrent gain with respect to the baseline cell of on average 5% to 10% is observed, with a few cases achieving around 30% gain. While the local field enhancement is moderate resonances for nitrides spread over the whole UV-VIS range. For some nitrides, the shading effect remains a problem similar as for metals, but others behave more like dielectric scatterers with high photocurrent gain.

Aiming the characterization of road dusts on the surrounding villages of an active mine and to assess metal(loids) bioaccessible fractions, a dust samples survey was undertaken. To achieve these objectives, pseudototal element concentration, mineralogical composition, Enrichment factor and in vitro extraction UBM assay for both gastric (G) and gastrointestinal (GI) phases, were determined. Results obtained revealed that arsenic represents the higher risk to humans, with mean pseudototal values higher than the maximum reference value range. Enrichment factor points to As significant to very high enrichment in all villages. Particles enriched in As, Ca, Fe, Cu, Al, Ti were identified by SEM-EDS in weathered agglomerates, linked to mine wastes and long-distance transport, both by wind and/or traffic. Arsenic bioaccessibility fraction (%BAF) presents low values in the studied samples, possibly due to low Fe complexes solubility with adsorbed As, limiting arsenic release and reducing its bioaccessibility. Concentrations of Cd bioaccessible G and GI phases are within the reference values range, while for Cu are above and for Pb are lower, than reference value range. Results show that the pseudototal fraction risk is overestimated when comparing to BAF (bioaccessible fraction), nevertheless, total G and GI risk are above the carcinogenic target risk (1.00E-06) in most samples. Carcinogenic risk of the bioaccessible contaminants shows that As is the element that represents higher risk for developing cancer over a lifetime, being ingestion the main risk route.

Metal toxicity in soils, along with water runoff, are increasing environmental problems that affect agriculture directly and, in turn, human health. In light of finding a suitable and urgent solution, research on plant treatments with specific compounds that can help mitigate these effects has increased, and thus the exogenous application of melatonin (MET) and its role in alleviating the negative effects of metal toxicity in plants, have become more important in the last few years. MET is an important plant-related response molecule involved in growth, development, and reproduction, and in the induction of different stress-related key factors in plants. It has been shown that MET plays a protective role against the toxic effects induced by different metals (Pb, Cd, Cu, Zn, B, Al, V, Ni, La, As, and Cr) by regulating both the enzymatic and non-enzymatic antioxidant plant defense systems. In addition, MET interacts with many other signaling molecules, such as reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. Furthermore, MET treatment enhances osmoregulation and photosynthetic efficiency and increases the concentration of other important antioxidants such as phenolic compounds, flavonoids, polyamines (PAs), and carotenoid compounds. Some recent studies have shown that MET appeared to be involved in the regulation of metal transport in plants, and lastly, various studies have confirmed that MET significantly upregulated stress tolerance-related genes. Despite all the knowledge acquired over the years, there is still more to know about how MET is involved in the metal toxicity tolerance of plants.

This mini-review critically summarizes the knowledge of imprinted polymer-based electrochemical sensors, for the detection of pesticides, metal ions and waterborne pathogenic bacteria, focusing on the period the last 5 years (citation of 78 papers published in 2017-2021, ie 63% of total citations). MIP-based electrochemical sensors exhibit low limit of detection, high selectivity, high sensitivity and low cost. Herein, we focused on the timely topics of water pollution by organics, inorganics and micro-organisms represented by pesticides, metal ions and bacteria, respectively. We put the emphasis on the design of imprinted polymers and their composites and coatings by radical polymerization, oxidative polymerization of conjugated monomers or sol-gel chemistry. Whilst most imprinted polymers are used in conjunction with differential pulse or square wave voltammetry for sensing organics and metal ions, electrochemical impedance spectroscopy (EIS) appears as the chief technique for detecting bacteria. This successful combination of EIS and imprinting technology should be harnessed in the coming years in the case of bacteria. Interestingly, bacteria are not always probed by bacteria-imprinted polymers; we report here their detection by monitoring specific (macro)molecules that reflect bacterial activity, for example quorum sensing signaling molecules or flagella proteins. If much has been developed in the past decade with glassy carbon or gold electrodes, it is clear that carbon paste electrodes of imprinted polymers are more and more investigated due to their versatility. Shortlisted case studies were critically reviewed and discussed; clearly a plethora of tricky strategies of designing selective electrochemical sensors are offered to “Imprinters”. We anticipate this review will be of interest to experts and new comers in the field who are paying time and effort combining electrochemical sensors with MIP technology.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The energy crisis and environmental problems are becoming more and more severe due to the long-term consumption of fossil fuels. Therefore, energy conversion devices with high energy density and environmental friendliness (such as fuel cells, metal-air batteries, etc.) have been ex-pected to be reliable alternatives to traditional fossil energy. However, due to the inevitable use of precious metals as the electrode catalysts for these devices, the popularization of these alternatives is seriously hindered. Transition metal nitrides (TMNs) exhibit similar surface and adsorption properties to noble metals since the atomic distance between metal atoms increases and the d-band center of metal atoms downshift after the nitrogen atoms enter the metal lattice. TMNs have become one of the best electrode materials to replace noble metal electrocatalysts in energy storage and conversion devices. In this review, the latest development in the electrocatalytic ap-plication of TMNs nanocrystalline is covered. Firstly, we briefly discuss the structure and activity origin of TMNs and introduce the common physical and chemical methods for the preparation of TMNs. Subsequently, we illustrate the applications of unary TMNs and multivariate TMNs in oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Finally, we summarize the challenges and problems of TMNs encountered at the present stage, and expect its future de-velopment.

Heavy metals have adverse effects on microalgae growth and metabolism. Photosynthesis and lipid profile are quite sensitive to heavy metal toxicity. The impact of chromium (Cr) on growth and photosynthetic activity of Dictyosphaerium pulchellum and Micractinium pusillum exposed to different concentrations (0 – 500 μg L-1) was investigated for 11 days. The influence of Cr on cell density and cell number followed similar trends, indicating a possible correlation among these growth responses. A significant (p < 0.05) increase in lipid content was observed with the increasing concentration of Cr however, growth was suppressed at higher concentrations exceeding 100 μg L-1. Addition of Cr in the cell culture medium showed a negative effect on quantum yield (Fv/Fm) and a photosynthetic inhibition of > 65% was noted in both species at 500 μg L-1. However, the lipid gravimetric analysis presented inner cell lipid content up to 36% and 30% of dry weight biomass for D. pulchellum and M. pusillum, respectively. The effects of chromium on growth and lipid accumulation in both microalgae species was concentration and exposure time dependent. This shows that an appropriate concentration of chromium in culture medium could be beneficial for higher lipid accumulation in freshwater eukaryotic microalgae species.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

Metal organic frameworks (MOFs) composed of metal ions and multifunctional organic ligands are one of the most attractive porous materials. Their potential applications in gas storage, separation, catalysis, biomedicine and many other fields have attracted much attention. In this study, Nano-Mn-MOF-74 with nano size were successfully synthesized by adding acetic acid and characterized it by SEM, TEM and XRD. Furthermore, a new method to trace the degradation process of nanoMOFs through detection of ligand concentration under physiological conditions was developed.

Monitoring volatile organic compounds (VOCs) places a crucial role in environmental pollutants control and indoor air quality. In this study, a metal-oxide (MOx) sensor detector (used in a commercially available monitor) was employed to delineate the composition of air containing three common VOCs (ethanol, acetone and hexane) under various concentrations. Experiments with a single component and double components were conducted to investigate how the solvents interact with the metal oxide sensor. The experimental results revealed that the affinity between VOC and sensor was in the following order: acetone > ethanol > n-hexane. A mathematical model was developed, based on the experimental findings and data analysis, to convert the output resistance value of the sensor into concentration values, which in turn can be used to calculate a VOC-based air quality index. Empirical equations were established based on inferences of vapor composition versus resistance trends, and on an approach of using original and diluted air samples to generate two sets of resistance data per sample. The calibration of numerous model parameters allowed matching simulated curves to measured data. As such, the predictive mathematical model enabled quantifying not only the total concentration of sensed VOCs, but also estimating the VOC composition. This first attempt to obtain semi-quantitative data from a single MOx sensor, despite remaining selectivity challenges, is aimed at expanding the capability of mobile air pollutants monitoring devices.

The paramagnetic gadolinium(III) ion is used as contrast agent in magnetic resonance (MR) imaging to improve the lesion detection and characterization. It generates a signal by changing the relaxivity of protons from associated water molecules and creates a clearer physical distinction between the molecule and the surrounding tissues. New gadolinium-based contrast agents displaying larger relaxivity values and specifically targeted might provide higher resolution and better functional images. We have synthesized the gadolinium(III) complex of formula [Gd(thy)2(H2O)6](ClO4)3·2H2O (1) [thy = 5-methyl-1H-pyrimidine-2,4-dione or thymine], which is the first reported compound based on gadolinium and thymine nucleobase. 1 has been characterized through vis-IR, SEM-EDAX and single-crystal X-ray diffraction techniques, and its magnetic and relaxometric properties have been investigated by means of SQUID magnetometer and MR imaging phantom studies, respectively. On the basis of its high relaxivity values, this gadolinium(III) complex can be considered a suitable candidate for contrast enhanced magnetic resonance imaging.

Bacteria a Microscopic organisms are the most inexhaustible and flexible of microorganisms and constitute a huge division of the whole living earthly biomass, certain microorganisms were found to amass metallic components at a high limit Was Known as Bacterial Bio-sorption Due to their little size, capacity to become under controlled conditions, and their Accommodation to an extensive variety of ecological situations; Potent metal bio-sorbents among microorganisms, at low pH esteems, cell divider ligands are protonated and contend essentially with metals for official. With expanding pH, more ligands, such as amino and carboxyl groups, could be exposed, leading to attraction between these negative charges and the metals, and consequently increment bio-sorption onto the cell surface. Starting with Isolation and identification of heavy metal-resistant bacteria from rock Ore. Studying Factors Affecting Uranium Bio-sorption, Optimization of bacterial growth conditions and optimum for metal uptake by free and immobilized bacterial cells and Desorption ratio of uranium ions adsorbed by Coli. /alginate, All this evidence suggest that functions groups Represented in our study are responsible for metal uptake in our bacterial biomass beside change in peaks position which assigned for it's groups confirm bio-sorption of metal ions from waste due to ions charge interaction comparing with immobilized we found increase in no of binding sites indicate that immobilized bacterial have high efficiency for metal up take which also change in peaks position which assigned for its groups confirm bio-sorption of metal ions from waste due to ions charge interaction, Where the high bio-sorption yield obtained by bacteria, the Uranium & heavy metal bioremediation process expects microorganisms to be joined to a strong surface.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

The purpose of this study was to arrange a green roof on a sheet metal house to achieve winter heat preservation and summer thermal insulation using different plants and soil media, and to maintain the advantage of cost-saving and quick installation of sheet metal houses. In terms of the research method, the roof insulation, heat preservation and plant growth index were tested. Plants were grown in 10 container-type green roofs on the sheet metal house roof, and the physical environment of the building was monitored for one year. Five containers of commercially-available culture soil and five containers of sustainable composite were used as the media for growing five kinds of plants, respectively. The control group only had a sheet metal house roof. There were 11 experimental modules for testing whether the green roofs had thermal insulation, heat preservation and plant growth effects on a general sheet metal house. The results showed that, regarding the thermal insulation benefit assessment, the Sedum acre cv. robustum of green roof Groups B to D caused the temperature to be 38.29°C lower than the surface of the simple sheet metal house roof in August, showing a temperature difference of 54%.

We report that ethanol, used together with water, plays a crucial role in tuning the structures of a zirconium-based Metal-Organic Framework, the 12-connected MOF-801, and the possible mechanisms of this modulating effect. By employing the cosolvent system of ethanol and water just under room temperature without the presence of a monotopic carboxylic acid as the modulator, MOF-801 in various morphologies of different sizes can be synthesized. The linear correlation between the ethanol/water ratio and the crystal sizes is also demonstrated. The growth mechanism is mainly explained by ethanol’s binding with the metal ion clusters and the Marangoni Flow Effect. Ethanol competes with the linker molecules in coordinating with the Zr metal clusters, a role similar to that of the modulators. The Marangoni Flow Effect, which dominates at a certain solvent ratio, further promotes the 1-D alignment of the MOF-801 crystals.

Additive manufacturing (AM) is an emerged layer-by-layer manufacturing process. However, its broad adoption is still hindered by limited material options, different fabrication defects, and inconsistent part quality. Material extrusion (ME) is one of the most widely used AM technologies, and, hence, is adopted in this research. Low-cost metal ME is a new and AM technology used to fabricate metal composite parts using sintered metal infused filament material. Since the involved materials and process are relatively new, there is a need to investigate the dimensional accuracy of ME fabricated metal parts for real-world applications. Each step of the manufacturing process, from the material extrusion to sintering, might significantly affect the dimensional accuracy. This research provides a comprehensive analysis of dimensional changes of metal samples fabricated by the ME and sintering process, using statistical and machine learning algorithms. Machine learning (ML) methods can be used to assist researchers in sophisticated pre-manufacturing planning and product quality assessment and control. This study compares linear regression to neural networks in assessing and predicting the dimensional changes of ME made components after 3D printing and sintering process. The prediction outcomes using a neural network performed the best with the highest accuracy as compared to regression. The findings of this study can help researchers and engineers to predict the dimensional variations and optimize the printing and sintering process parameters to obtain high quality metal parts fabricated by the low-cost ME process.

Hybrid metal-organic compounds as relatively new and prosperous magnetoelectric multiferroics provide opportunities to improve the polarization, magnetization and magneto-electric coupling at the same time, which usually have some limitations in the common type-I and type-II multiferroics. In this work we investigate the crystal of guanidinium copper(II) formate [C(NH2)3]Cu(HCOO)3 and give novel insights concerning the structure, magnetic, electric and magneto-electric behaviour of this interesting material. Detailed analysis of crystal structure at 100 K is given. Magnetization points to the copper(II)-formate spin-chain phase that becomes ordered below 4.6 K into the canted antiferromagnetic (AFM) state, as a result of super-exchange interaction over different formate bridges. The performed ab-initio colinear density functional theory (DFT) calculation confirm the AFM-like ground state as a first approximation and explain the coupling of spin-chains into the AFM ordered lattice. In versatile measurements of magnetization of a crystal, including transverse component besides the longitudinal one, very large anisotropy is found that might originate from canting of the coordination octahedra around copper(II) in cooperation with the canted AFM order. With cooling down in zero fields the generation of spontaneous polarization is observed step-wise below 270 K and 210 K and the effect of magnetic field on its value is observed also in the paramagnetic phase. Measured polarization is somewhat smaller than the DFT value in the c-direction, possibly due to twin domains present in the crystal. The considerable magneto-electric coupling below the magnetic transition temperature is measured with different orientations of the crystal in magnetic field, giving altogether the new light onto the magneto-electric effect in this material.

Abstract: This work is part of the interest of solving the problems of water contamination with last generation pollutants, for which a novel and in an aqueous medium FeBTC material incorporated with magnetite nanoparticles was proposed. That material was synthesized by in situ solvothermal method, the Fe3O4 nanoparticles were added during the Fe-BTC MOF synthesis and used in the drug’s adsorption. The materials were characterized by XRD, FTIR and Raman spectroscopy, and N2-physisorption at 77 K. Fe3O4-FeBTC material showed a maximum adsorption capacity of 357.1 mg g−1 for diclofenac sodium, 70.9 mg g−1 for naproxen sodium, and 122.9 mg g−1 for Ibuprofen. A pseudo-second-order kinetic model can describe the adsorption process, and the thermodynamic study revealed that the adsorption of the three drugs was a feasible, spontaneous, and exothermic process. The incorporation of magnetite nanoparticles in the FeBTC considerably increased the adsorption capacity of pristine FeBTC. Also, hybridization of the FeBTC with magnetite nanoparticles reinforced the most vulnerable part of the MOF, increasing its thermal and aqueous media stability. The electrostatic interaction, H-bonding, and interactions in the open-metal sites played a vital role in drug adsorption. The competition of sites in the multicomponent mixture's adsorption showed selective adsorption at diclofenac sodium and naproxen sodium.

In recent years, many researchers have begun to shift their focus onto the synthesis of nanomaterials as this field possesses immense potential that may provide incredible technological advances in the near future. The downside of conventional synthesis techniques, such as co-precipitation, sol-gel and hydrothermal methods, is that they necessitate the use of toxic chemicals, produce harmful by-products and require a considerable amount of energy; therefore, more sustainable fabrication routes are sought after. Biological molecules have been previously utilised as precursors to nanoparticle synthesis, thus eliminating the negative factors involved in traditional methods. In addition, transition-metal nanoparticles possess a wide scope of applications due to their multiple oxidation states and large surface areas; thereby allowing for a higher reactivity when compared to their bulk counterpart and rendering them an interesting research topic. However, this field is still relatively unknown and unpredictable. Therefore, this review aims to obtain a better understanding on the plant-mediated synthesis process of the major transition-metal and transition-metal oxide nanoparticles, and how different parameters affect their unique properties.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

As a candidate for bifunctional asymmetric catalysts containing a half-sandwich C–N chelating Ir(III) framework (azairidacycle), a dinuclear Ir complex with an axially chiral linkage is newly designed. An expedient synthesis of chiral 2,2’-bis(aminomethyl)-1,1’-binaphthyl (1) from 1,1-bi-2-naphthol (BINOL) was accomplished by a three-step process involving nickel-catalyzed cyanation and subsequent reduction with Raney-Ni and KBH4. The reaction of (S)-1 with an equimolar amount of [IrCl2Cp*]2 (Cp* = 5-C5(CH3)5) in the presence of sodium acetate in acetonitrile at 80 °C gave a diastereomeric mixture of new dinuclear dichloridodiiridium (5) through the double C–H bond cleavage, as confirmed by 1H NMR spectroscopy. A loss of the central chirality on the Ir centers of 5 was demonstrated by treatment with KOC(CH3)3 to generate the corresponding 16e amidoiridium complex 6. The following hydrogen transfer from 2-propanol to 6 provided diastereomers of hydrido(amine)iridium with retaining the bis(azairidacycle) architecture. The dinuclear chlorido(amine)iridium 5 can serve as a catalyst precursor for the asymmetric transfer hydrogenation of acetophenone with a substrate to catalyst ratio of 200 in the presence of KOC(CH3)3 in 2-propanol, leading to (S)-1-phenylethanol with up to 67% ee.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

FeIFeI Fe2(S2C3H6)(CO)6(µ-CO) (1a-CO) and its FeIFeII cationic species (2a+-CO) are the simplest model of the CO-inhibited [FeFe] hydrogenase active site, which is known to undergo CO photolysis within a temperature- dependent process whose products and mechanism are still a matter of debate. Using Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TDDFT) computations, the ground state and low-lying excited state potential energy surfaces (PESs) of 1a-CO and 2a+-CO have been explored aimed at elucidating the dynamics of the CO photolysis yielding Fe2(S2C3H6)(CO)6 (1a) and Fe2(S2C3H6)(CO)6+ (2a+), two simple models of the catalytic site of the enzyme. Two main results came out from these investigations. First, a-CO and 2a+-CO are both bound with respect to any CO dissociation with lowest free energy barriers around 10 kcal mol-1, suggesting that at least 2a+-CO might be synthetized. Second, focusing on the cationic form, we found at least two clear excited state channels along the PESs of 2a+-CO that are unbound with respect to equatorial CO dissociation.

The Mediterranean Sea is one of the most impacted basin in terms of microplastics pollution. Land-based activities are the major sources of plastic litter to the ocean, with harbors probably representing significant hotspots. In the framework of the SPlasH! project (Stop alle Plastiche in H2O, Interreg Marittimo project), microplastics were sampled in three north-western Mediterranean harbors during summer and winter. In this study, the areal concentrations of microplastics ranged from 5,576 to 379,965 items.km-2. A decreasing gradient was observed from the inner to the outer zones of the studied harbors, pointing out these enclosed systems as hotspots regarding microplastic pollution. During the summer, because of an enhancement of port activities, the areal concentrations of microplastics were higher than in winter. The investigation microplastics size classes distribution in the surface waters revealed that microplastic within a size range between 300 µm and 500 µm were depleted. During this study, we assessed trace metal partitioning (Pb, Fe, Cu, V, Cd and As) between the dissolved phase and biofilm, thus highlighting concentrations within the biofilm two and six orders higher than those in the dissolved phase. This result strongly suggest trace metal bioaccumulation within the biofilm. When trace metal concentrations are normalized over the corresponding surface of microplastics and microplastics, higher values were obtained for microplastics evidencing their enhanced capacities to bioaccumulate contaminants with respect to macroplastics.

The wide interest in developing green energy technologies stimulates the scientific community to seek, for devices, new substitute material platforms with low environmental impact, ease of production and processing and long-term stability. The synthesis of metal oxide (MO) semiconductors fulfils these requirements and efforts are addressed at optimizing their functional properties, through improvement of charge mobility or energy level alignment. Two MOs have rising perspectives for application in light harvesting devices, mainly for the role of charge selective layers but also as light absorbers, namely MoO3 (an electron blocking layer) and Co3O4 (a small band gap semiconductor). The need to achieve better charge transport has prompted us to attempt doping strategies with vanadium (V) ions that, when combined with oxygen in V2O5, produce a high work function MO. We report on subcritical hydrothermal synthesis of V-doped mesostructures of MoO3 and of Co3O4, in which a tight control of the doping is exerted by tuning the relative amounts of reactants. We accomplished a full analytical characterization of these V-doped MOs that unambiguously demonstrates incorporation of the vanadium ions in the MO crystal lattice, as well as effects on the optical properties and work function. We foresee a promising future use of these materials as charge selective materials in energy devices based on multilayer structures.

This article presents the development of the theoretical background and the design of an electronic device for monitoring the condition of a gapless Metal Oxide Surge Arrester (MOSA). The device is intended to be used online. Due to the inaccessibility and possible remote location of most surge arresters, it is equipped with a communication system, allowing the device to convey the measurement of the surge arrester characteristics under any conditions. By gathering measurements of the surge arrester’s resistive component of leakage current, it is possible to determine the condition of the MOSA. After interpreting the results, these can be sent via a data transfer unit to a server, which, in turn, sends it onward to the authorised personnel through the surge arrester control centre.

The effect of rare earth Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results showed that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites, and significantly improve the toughness of weld metal. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. However, excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties, and the corresponding values were 835MPa of tensile strength and 72 J of impact toughness. These findings suggest that the control of Pr6O11 can be an effective way to improve the impact toughness of weld metal.