This research focuses on exploring generalized electron emissions in one-dimensional conducting materials, specifically examining field emission and thermionic emission. Additionally, the study investigates one-dimensional thermal radiation. The current density is derived for both one-dimensional thermionic emission and one-dimensional field emission. A generalized current density in one dimension is devised, taking into account arbitrary accelerating fields and temperature conditions. The formula for the one-dimensional current density is depicted with accelerating field and temperature across various work function materials. The current is also represented as a function of both temperature and electric field for various temperatures.

In China's mountainous coastal terrain, the storm badly damaged low-rise buildings. At present, it is not clear how the relative position of buildings and mountains affects the surface of a low-rise building’s fluctuating coefficient. The study compared these results with the wind pressure distribution without the surrounding environment. The primary objective of this study is to examine the fluctuating coefficient variation rule based on the spacing between hillsides and buildings under 0° wind angle. Additionally, the study analyzes the fluctuating wind pressure coefficient across wind angles between 0°~90°. The distribution of wind pressure in different common hillside landforms was examined through a wind tunnel experiment, which also compared with the distribution in an open environment. The study examined the fluctuating coefficient as the distance between the building and the hillside changed, specifically for wind blowing at a 0° angle. Next, an analysis is conducted on the changing pattern of the fluctuating coefficient for low-rise buildings ranging from a wind angle of 0° to 90°. Simultaneously, the investigation examined the power spectrum and wind pressure’s probability distribution, while considering the proximity of the building to an adjacent hill. The findings indicated that the changing wind pressure factor on the surface of the structure differed based on the relative location of the hillside and the building. The roof's wind pressure coefficient fluctuated and gradually increased until it reached its peak, unaffected by the surroundings. The low-frequency energy decreased in windward eaves, while the high-frequency energy progressively rose as the distance between the hillside and the building increased. The wind pressure on the leeward side exhibited Gaussian characteristics in its probability distribution.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Speeding is a significant global issue, with disparities in speed outcome and speed research between low- and middle-income countries (LMICs) and high-income countries (HICs). This study aims to address speed research gaps by examining the prevalence of self-reported speeding and factors influencing drivers' speeding behavior (SB) using the Theory of Planned Behavior (TPB). An online survey involving 387 anonymous drivers was conducted in Yaoundé. Results showed that all drivers reported exceeding speed limits, with 81% exceeding by 5km/h, 12% by 10km/h, and 7% by more than 10km/h in urban areas. On highways, 54% reported exceeded the limit by more than 10km/h. Age, driver's license, and gender showed significant associations with speed limits non-compliance. The study results suggests that the TPB can be useful in assessing speeding behavior, as the inclusion of TPB variables led to a more than 50% proportionate increase in SB variance. Structural equation modeling revealed attitude towards speeding as the strongest predictor of speeding intention (SI), along with certain demographics indirectly influencing SB through SI. Perceived behavioral control (PBC) and SI directly influenced SB. These findings emphasize the potential of interventions targeting attitude, intentions, and perceived behavioral control to modify speeding behavior and improve road safety.

The paper presents modelling of relationships between wind velocity distributions observed in Poland and technical requirements for wind power stations design. The wind velocities distributions for various locations in Poland are determined, and expressed in Weibull distribution parameters. Theoretical computations concerning the dependence of wind power station as function of wind speed and aire physical properties are presented. Conclusions important for design of power stations fitted to atmospheric conditions in Poland are given. Wind power plants have been an important source of electricity generation for many years.Wind power modelling with the use of wind speed is used to improve the accuracy of forecasts and analyses of the power production of wind farms.

The traditional approach of considering the probability distribution of rain attenuation leads to overdesign the power margin of data channels. We have first recalled a method, proposed in 2016, which with a small power margin, bandwidth expansion and variable symbol rate avoids overdesign and can transfer the same data volume as if the link were in clear–sky conditions. It is charaterized only by the link mean efficiency 0≤η≤1, suitably defined. It is usefull only if: (a) data must be downloaded also when it is raining; (b) real–time communication is not strictly required. We have applied it to the links of GeoSurf satellite constellations by simulating rain attenuation time series at 80 GHz (mm–wave) with the Synthetic Storm Technique, from rain-rate time series recorded on–site, at sites located in different climatic regions. The power margin to be implemented ranges from 2.0 dB to 7.4 dB – well within the current technology – regardless the instantaneous rain attenuation. The clear–sky bandwidth is expanded 1.75 to 2.80 times, not large per se, but it may challenge current technology if the clear–sky bandwidth is already large.

In the context of carbon neutrality and carbon peaking, in order to achieve low carbon emissions and promote the efficient utilization of wind energy, hydrogen energy as an important energy carrier is proposed to mix hydrogen and natural gas to form hydrogen enriched compressed natu-ral gas (HCNG). It is also injected into the natural gas pipeline network to realize the transmission and utilization of hydrogen energy. At the same time, the participation of demand response is considered, the load peak and trough period is adjusted, and large-scale consumption of renewa-ble energy and the reduction of carbon emissions are realized. First of all, a fine model of hydro-gen production and hydrogen use equipment is established to analyze the impact of adding hy-drogen mixing on the economy and low-carbon of the system. With green certificates and demand response, the utilization rate of hydrogen energy is improved to further explore the energy utiliza-tion rate and emission reduction capacity of the system. Secondly, on the basis of modeling, the optimal scheduling strategy is proposed with the sum of energy purchase cost, equipment opera-tion cost, carbon emission cost, wind curtailment cost and green certificate income as the lowest objective function. Considering the constraints such as hydrogen blending ratio and flexible load ratio of the pipeline network, a low-carbon economic scheduling model of hydrogen mixed natu-ral gas was established. The model was linearized and solved by using MATLAB and CPLEX solver. By comparing different scenarios, the superiority of the model and the effectiveness of the strategy are verified.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Recently, Gohar et al. introduced a novel, local, and well-behaved fractional calculus. It possesses all the classical properties, and Its locality imposes simplicity and accuracy in modeling fractional order systems. In this article, we further develop the definitions and extend the classical properties of Gohar fractional calculus to address some of the open problems in Calculus. The fractional Gronwall's integral inequality, Taylor power series expansion, and Laplace transform are defined and applied to overcome some of the limitations in the classical integer-order calculus. The fractional Laplace transform is applied to solve Bernoulli-type logistic and Bertalanffy nonlinear fractional differential equations, and the criteria under which it can be applied to solve linear differential equations are investigated.

While providing safe water for the rural poor is considered a basic human right, there are numerous issues associated with existing technologies with shortcomings. Performance issues have continued to fail to meet the needs of impoverished families due to issues including high cost, difficulties with performance, and continuing needs for maintenance. These issues have severely interfered the safe water accessibility. Key aspects of the Guelph Water Filter (GWF) system can avoid/minimize many of these issues. The GWF as described herein enables delivery of low cost, long-term performance at 3Log removal of E.coli and can deliver 1 to 3 L of treated water per hour. The GWF is simple to operate, has an ability to provide sufficient water for a family, maintains longevity of performance, is easy to maintain and has protection against breakage during the cleaning process, is repairable at village level, and operates using a sizable reservoir of water to supply raw water, meaning the technology does not need to be refilled frequently. Hence, the capability of the novel GWF technology is shown to bypass many of the troublesome features of alternative low-tech water treatment technologies. The potential for the GWF to function for 2 days continuously avoids the need for young girls to fetch raw water frequently during a day, thereby enabling them to attend school. Hence, the GWF enhances the potential to result in ‘safe water and full schools’, providing the opportunity for girls to receive education and capture socio-economic benefits for the community.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

The Standard Model is not a complete description of reality; it omits the existence of dark matter, dark energy, and an explanation as to why no CP violation has been observed. However, some of these phenomena could be explained through a new force mediated by a new boson. If such a boson were massless it would result in a power law potential and if massive the interaction would be Yukawa-like. A previous experiment employing a micro-mechanical oscillator and a spherical test mass interactions was successful in placing the best limits on a mass-mass Yukawa-like interaction, but the data was never analyzed in the context of a power law. Here that data is analyzed considering a power law for powers n = 1-5 where n is the number of boson exchanges. The results show that the limits obtained through power law analysis of this data are not better than the currently accepted limits. A discussion of an experiment design capable of producing better limits on power law extensions to the Standard Model is presented, and suggests micro mechanical oscillators based experiment remains capable of improving the limits by at least one order of magnitude.

The Sanaga River Valley is a deep-seated structure of about 220 km in width, bounded on its northern and southern sides by 025-0550 fault zones. Its internal structure has been very little described before this study. It is characterized by the presence of surface features where a thick stratum of shale and argillaceous sandstones have been documented. The use of electrical resistivity tomography for near-surface imaging and hydrogeological prospecting within shale succession is widespread. However, several methods of spatial modeling of resistivity contours are generally proposed for the interpretation of inverse resistivity model sections. To determine the most appropriate method for interpreting resistivity tomographies in the context of subsoil marked by significant heterogeneity, logarithmic contour intervals, and linear contour interval processing were implemented on data collected over five areas. The data consists of outcrops data, cuttings samples from groundwater boreholes, and resistivity sections ranging in length from 240 to 1000 m. Well-control of the inverse resistivity model sections derived from both processes shows that the linear contour intervals modeling gives a more realistic picture of the reservoir size of the wa-ter-bearing sand in both shale and argillaceous sandstone succession. The sedimentary architecture over Sanaga fault breccia is marked by vertical intrusion anomalies up to 80 m high. The shape of these anomalies, as well as the very low resistivity values that characterize them, suggests that they could be related to mud intrusion.

(1) Background: This paper details the development process of two assistive technology products (ATs) implemented in the PAID project, aiming to promote the social, educational, and labor inclusion of people with disabilities across 10 municipalities of Antioquia, Colombia. (2) Methods: Applying Design Thinking (DT) methodology, including stages of empathizing, defining, ideating, prototyping, and testing, alongside a demographic study where specific needs of people with disabilities (PwDs) were identified. (3) Results: As a result, the construction process of two specific cases of assistive technology products (ATs) is detailed, including finite element simulation, mechanical testing, and delivery to end-users. Additionally, workshops for assistive product fabrication conducted in select municipalities of the project are highlighted. (4) Conclusions: the information gathered guided the development of the ATs, focusing on their features on accessibility and ease of replication. The primary objective is to facilitate the participation of PwDs in educational environments, thus promoting inclusion and accessibility. This article describes the results of two of these ATs; however, it is worth noting that this process was performed for 112 ATs delivered through the duration of the project.

A regional modern river-sand geochemical mapping study in the majority of the Timor-Leste territory, including the research area, has not been previously reported. This study demonstrated the potential of modern river sand geochemical mapping as an effective method for lithological mapping, particularly in areas that face challenges in conducting efficient geological fieldwork and have limited geological information. A total of 53 modern river sand samples were collected and analyzed. Before examining the samples using wavelength-dispersive X-ray fluorescence for ten major elements, the loss-on-ignition method was employed. In the Clerec drainage basin, SiO2, CaO, and K2O showed positive correlations, and CaO was positively correlated with MnO. Similarly, in the Sahe River catchment, a positive relationship was observed between CaO, MnO, and TiO2. These findings suggested the presence of quartz, manganese, secondary K-bearing minerals, and secondary Ti-bearing minerals in carbonate rocks that have undergone silicification and other alteration processes. The principal component analysis results corroborated the SiO2/Al2O3 and K2O/Na2O ratios and the ICV findings. PC1 was related to the variations in Ca-poor and Ca-rich rocks; PC2 indicated notable inputs from SiO2-rich and SiO2-poor rocks; and PC3 revealed the possibility of contributions from secondary mineral assemblages related to silicification and low-grade metamorphic processes.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

Plasma electrolytic polishing (PeP) is mainly used to improve the surface quality and thus the performance of electrically conductive parts. It is usually used as an anodic process, i.e. the workpiece is negatively charged. However, the process is susceptible to high current peaks during the formation of the vapour skin especially when polishing workpieces with a large surface area. In this study, the critical influence of workpiece submerging velocity on the current peaks and the average power during the initialisation of the PeP process is investigated for a workpiece size of microreactor mould insert. Through systematic experimentation and analysis, this work provides insights into the control of the initialisation process by modulating the workpiece submerging velocity. The results clarify the relationship between submerging velocity, peak current and average power and provide a novel approach to improve process efficiency in PeP. The highest peak current and average power occur when the electrolyte splashes over the top of the workpiece and not, as expected, when the workpiece touches the electrolyte. By submerging the workpiece while the voltage is applied to the workpiece and counter electrode, the reduction in both parameters is over 80 %.

Climate change has become a global nightmare, and the awareness of the causes of carbon emissions have resulted in rigorous studies. These studies linked the increase in global warming with booming economic growth. Since global warming has become more apparent, researchers have explored ways to decouple economic activities from carbon growth. Economic and carbon growth must be decoupled to achieve a low-carbon economy to support the carbon growth plan or emission reduction strategy. The world is transitioning towards a carbon-neutral and green ecosystem, so finding ways to decouple carbon emissions from economic activities is an exciting topic to explore. The study reviews current information on the importance of decoupling energy from economic growth innovative techniques that thoroughly examine the challenges and constraints of low-carbon energy systems. This review revealed that decarbonization and dematerialization had been achieved without declining global economic growth. It also provides information on energy use and economic activities leading to global carbon emissions and alternative solutions to the global challenge of climate change. The decoupling methods commonly used to determine the impact of energy decarbonization on economic growth are explored. All suggested that economic growth is a primary mover of global carbon emission increase and must be separated to achieve a carbon environment.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

GNSS is nowadays a standard tool for monitoring and studying the Earth’s dynamic environment. However, the development of dense GNSS measurements remains limited in many experiments by the cost of geodetic-class equipments allowing to achieve the high precision required by many applications. Recently, multi-constellation, multi-frequency, low-power and, above all, less expensive GNSS electronic chips have become available. We present a prototype of a low-cost, open-source multi-GNSS station. Our prototype comprises a dual-frequency GNSS chip, a calibrated antenna, a Raspberry Pi card and a 4G key for data transmission. The system is easy to deploy in the field and allows precise positioning in real time and post-processing. We assess the performance of our prototype in terms of raw data quality, and quality of the obtained high rate and daily position one-year-long time series. Our results demonstrate a quality equivalent to geodetic-class equipment and better quality than other low-cost systems proposed so far.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

This study determines the equivalent stress intensity factor (SIF) model that best fits the experimental behavior of low-carbon steel under mixed mode (I and II). The study assessed Tanaka, Richard, and Pook's equivalent SIF models. The theoretical values used for comparison correspond to experimental results in a modified C(T) geometry by machining a hole ahead of the crack tip subjected to fatigue loads with a load ratio of R = 0.1. The comparison involved the SIF for six experimental points and the values computed through the numerical simulation. The Paris, Klesnil, and modified Forman-Newman crack growth models were used with each equivalent SIF to analyze the prediction in the estimated number of cycles. The Klesnil model showed the closest prediction since the error between the calculated and experimentally recorded number of cycles is the lowest. However, the material behavior reflects a reduced crack propagation rate attributed to plasticity in the crack tip. Results suggest that Asaro equivalent SIF conservatively estimates the element lifespan with increasing errors from 2.3% at the start of growth to 27 % at the end of the calculation.

The COVID-19 pandemic halted progress in global vaccine coverage and disrupted routine childhood vaccination practices worldwide. While there is ample evidence of vaccination declines experienced during the pandemic, it is less clear how low-income countries were affected. We executed a systematic review to synthesize the current literature on impacts to routine childhood vaccinations in low-income countries from January 1, 2020 to February 8, 2023. We collected data using an extraction form on Covidence and assessed the quality of studies included in the review using the Risk of Bias in Non-Randomized Studies of Interventions (ROBINS-I) tool. Effect estimates for changes in vaccination during the pandemic were reported and summarized. Factors that influenced changes were grouped into descriptive themes. Thirteen studies, encompassing 18 low-income countries and evaluating 15 vaccines at varying doses, were included in the final review. We found that routine childhood vaccinations during the COVID-19 pandemic varied considerably by vaccine type, location, and phase of the pandemic. Nine different themes were identified as factors that influenced changes in vaccination. Documenting past experiences and lessons learned is crucial for informing preparedness efforts in anticipation of future public health emergencies. Failure to effectively address these things in the next public health emergency could result in a recurrence of declining routine childhood vaccinations.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Abstract: Efforts for carbon emission reduction have been identified as a major climate change mitigation target in the Paris Agreement. The 26th Conference of Parties to the United Nations Framework Convention on Climate Change highlighted the worldwide effort for cleaner and greener mining, urging the mineral industry to embrace greener operational emissions reduction technologies and strategies. Ghana pledged at the Paris Conference to reduce CO2 emissions by 15% and increase renewable energy share to 10% of the national energy mix. Here the fundamental question is how Ghana’s mining industry can contribute to CO2 emission reduction efforts. This paper investigates barriers to low-carbon emission policy implementation among mining companies in Ghana. The questionnaire survey was conducted among Ghana’s four large-scale gold mining companies. As the sample number of available companies is limited, we used a descriptive analysis to assess the responses. The results show that the companies expressed widely different ways to respond to the issues of cost, a government policy/regulations for carbon emission reduction, and the adoption/acquisition of low-carbon technologies. Those companies that are relatively less prepared for this endeavor emphasized the uncertainties of securing sufficient energy in case of using low-carbon technologies. They also expressed a need for more trained workers to handle low-carbon technologies. All companies agreed with a expected high cost of adopting low-carbon options. There was a communication gap with the relevant government ministry about low-carbon mining options where the government should be able to facilitate the involvement of othe low technology providers, such as solar PV installation.

The origin of neurodegenerative diseases is linked to the abnormal folding of disease-associated proteins. The traditional amyloid hypothesis has been a focal point of research, but recent findings suggest a more complex picture. This review explores the role of physiological conformation of aggregation-prone domain (also known as prion-like low complexity domain) and multiple co-misfolded proteins in neurodegenerative diseases. We highlight the importance of targeting multi-heterotypic misfolded proteins for effective treatments and emphasize the irreversible neurodegeneration stemming from the loss of physiological folding in prion-like disease-causing proteins underscores the criticality of refolding. Additionally, we introduce the concept of ReproFold Therapeutics, a novel approach aimed at restoring the cellular prion-like folding of disease-causing proteins to rebuild normal cross-β interactomes and mitigate neurodegeneration. Baicalein, a potential drug candidate for this approach, shows promise in vitro and in animal models. Moreover, prion-like low complexity domains implicated in neurodegeneration are also associated with other disorders such as diabetes, cancers, and mental illnesses. Understanding the core pathology of neurodegenerative diseases and the broader implications of prion-like LC domains could revolutionize healthcare approaches and policies worldwide.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

This research paper examines a cosmological model in flat space-time via $f(R,G)$ gravity where $R$ and $G$ are respectively the Ricci scalar and Gauss-Bonnet invariant. Our model assumes that $f(R,G)$ is an exponential function of $G$ combined with a linear combination of $R$. We scrutinize the observational limitations under a power law cosmology that relies on two parameters - $H_0$, the Hubble constant, and $q$, the deceleration parameter, utilizing the 57-point $H(z)$ data, 8-point BAO data, 1048-point Pantheon data, joint data of $H(z)$ + Pantheon, and joint data of $H(z)$ + BAO + Pantheon. The outcomes for $H_0$ and $q$ are realistic within observational ranges. We have also addressed Energy Conditions, $Om(z)$ analysis and cosmographical parameters like Jerk, Lerk and Snap. Our estimate of $H_0$ is remarkably consistent with various recent Planck Collaboration studies that utilize the $\Lambda$CDM model. According to our study, the power law cosmology within the context of $f(R,G)$ gravity provides the most comprehensive explanation for the important aspects of cosmic evolution.

Wireless Sensor Networks are critical for modern applications ranging from environmental monitoring to smart city infrastructures. This research proposes a novel optimization learning and deployment strategy for Wireless Sensor Networks (WSNs) by 3D WUSN model is uniformly distributed M sensor nodes across diverse terrains, with clusters representing 20% of sensors, showcasing its ability to balance power consumption and extend network longevity, grounded in fuzzy clustering based protocol using the Fuzzy C-Means (FCM) method, called FCM-3DWUSN. Comparative analysis against established models including LEACH-C, K-Means and LEACH emphasized FCM-3DWUSN's outperformed performance, with average power consumption such as 134.990, 341.790, 143.895, and 192.984; respectively. The experimental result shows that FCM protocol in the 3D WUSN model can reduce energy consumption and improve the network lifetime to gather data and send the information.

This paper proposes training improvement methods of artificial neural networks (ANN) trajectory predictors. First, a dynamic power system time-series trajectory is split into several different segments to simplify the original ANN training problem. Moreover, the time-derivative of the trajectory is included to obtain an augmented loss function. Compared to previous studies which mainly focused on increasing the prediction accuracy, the aim of these novel techniques is to reduce the computational burden where the ANN output performance is still acceptable. The effectiveness of the developed methods is validated based on the WSCC three-machine nine-bus and IEEE 39-bus system models. The mean absolute error (MAE) and trajectory prediction results are analyzed, in which the numbers of neurons, hidden layers, and training epochs are constrained during the ANN training process. Rotor-angle difference between generators and the system frequency are investigated as the dynamic trajectories of the power system models. It is revealed that when the ANN architecture and epochs are constrained, the MAE results can be reduced, and the ANN training results can better reflect the original trajectory using the improvement approaches.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

The low-temperature environment significantly inhibits the growth and metabolism of denitrifying bacteria, leading to an excessive concentration of ammonia nitrogen and total nitrogen in sewage treatment plants during the cold season. In this study, an efficient denitrifying strain of heterotrophic nitrification–aerobic denitrification(HN-AD) bacteria named HS2 was isolated and screened from industrial sewage of a chemical factory in Inner Mongolia at 8°C. The strain was confirmed to be Achromobacter spiritinus, a colorless rod-shaped bacterium. When cultured with sodium succinate as the carbon source, a carbon-to-nitrogen ratio of 20-30, a shaking rate of 150-180 r/min, and the initial pH of 6-10, the Strain HS2 exhibited excellent nitrogen removal at 8°C. Through the results of whole-genome sequencing, gene amplification, and gas product detection, the Strain HS2 was determined to possess key enzyme genes in both nitrification and denitrification pathways, suggesting a HN-AD pathway of NH4+-N→NH2OH→NO2--N→NO→N2O→N2. At 8°C, the Strain HS2 could completely remove ammonia nitrogen from industrial sewage with an initial concentration of 127.23 mg/L. Microbial species diversity analysis of the final sewage confirmed Achromobacter sp. as the dominant genus, this indicated that the low-temperature denitrifying strain HS2 plays an important role in nitrogen removal of actual low-temperature sewage.

This study conducts a comprehensive review of the integration of Hybrid Electric Turbochargers in mass-produced road vehicles. The primary objective is to inform the readers about the potential advantages and innovative applications of HETs. Employing a SWOT analysis, the research compares the performance of HETs on thermal engines versus traditional turbochargers and HETs on thermal engines versus HETs on hybrid engines based on a synthesis of multiple research findings. The study elucidates the fundamental mechanics of turbochargers, emphasizing their inherent benefits. Additionally, it introduces a novel approach with the integration of the hy-brid-electric turbocharger, demonstrating its capacity, supported by practical examples. The in-corporation of turbochargers with energy recovery mechanisms, including HETs, is shown to significantly contribute to emissions reduction. Moreover, the electric drive facilitates the utili-zation of hybrid turbines, particularly on low-displacement engines, resulting in enhanced effi-ciency, torque, and liter power. In conclusion, the research underscores the potential of HETs to substantially mitigate the environmental impact of the transportation sector by reducing emis-sions and conserving energy. Their ability to optimize the fuel efficiency and power output of internal combustion engines, coupled with the feasibility of downsized engines, positions HETs as an attractive option for both manufacturers and consumers. However, it is acknowledged that the implementation of HETs is in its early stages, necessitating further research to comprehensively understand their environmental impact. Despite this, the promising positive impact on the en-vironment designates HETs as a technology deserving close attention in the forthcoming years.

Background. Implementing mammogram screening means that clinicians are seeing many breast cancers that will never develop metastases. The purpose of this study was to identify subgroups of breast cancer patients who did not present events related to long-term breast cancer mortality, taking into account diagnosis at breast screening, absence of palpability and axillary involvement, and genomic analysis with PAM50. Patients and Methods. To identify them, a retrospective observational study was carried out selecting patients without palpable tumour, without axillary involvement, and a genomic analysis was performed with PAM50. Results. The probability of distant metastasis-free interval (DMFI) of 337 patients was 0.92 (95% CI, 0.90-0.93) at 20 years and 0.96 (95% CI, 0.92-1.00) in 95 patients (28%) with available PAM50 tests. In 22 (23.15%) luminal A tumours and in 9 (9.47%) luminal B tumours smaller than 1 cm and in HER2 and basal type tumours there were no metastatic events (20-year DMFI of 1.00). Conclusion. Patients with nonpalpable breast cancer found at screening with negative nodes are at very low risk. It is possible to identify subgroups without metastatic events by determining the intrinsic subtype and tumour size less than 1 cm. De-escalation of treatment should be considered.

We propose a new methodology for long-time biopotential recording based on MEMS multisensor integrated platform featuring a commercial electrostatic charge transfer sensor. That family of sensors was originally intended for presence tracking in automotive, so the existing setup has been engineered for the acquisition of electrocardiogram, electroencephalogram, electrooculogram and electromyography, designing a dedicated front-end and writing a proper firmware for the specific application. Systematic tests on controls and nocturnal acquisitions from patients in domestic environment will be discussed in detail. The excellent results candidate this technology to provide a low power, unexplored solution to biopotentials acquisition. The technology breakthrough is in that it enables adding this type of functionality to existing MEMS boards at near-zero additional power consumption. For these reasons, they open to additional possibilities for wearable sensing and strengthen the role of MEMS technology in medical wearable applications for long time synchronous acquisition of a wide range of signals.

In recent years, researches on combining wavelet decomposition and convolutional neural network (CNN) together to classify hyperspectral images (HSI) have emerged, and some effective classification models have been proposed and achieved good classification results. However, there are two problems for most of the proposed models. One is the heavy training parameters and the other is that there is no distinction between the classification effectiveness of low frequency and high frequency features after wavelet decomposition. In this paper, a new light-weighted HSI classification model (LLFWCNN) is proposed, which performs multi-layer wavelet decomposition for HSI after dimensionality reduction, and only arranges the low frequency features in a specific stack mode, then classifies them through a well-designed convolutional neural network. Compared with other classification models, the number of parameters is only 2.5% of that of other models. And only the low frequency features after wavelet decomposition are used, while the high frequency features are abandoned. The results showed that compared with the state-of-the-art classification models, LLFWCNN could obtain the same or even better classification results with fewer network parameters and proved that the low frequency features after wavelet decomposition provide LLFWCNN with more favorable information for HSI classification as well.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

Technological advancements must keep pace with earth’s rising demand for energy, while minimizing the carbon footprint on earth. One such option is using space based solar (SBS) radio frequency (RF) microwave power beaming. This innovative and novel technology is currently being explored to address terrestrial photovoltaic (PV) intermittency and provide a method to transmit power to other spacecraft in various orbits. This modality of power generation and distribution presents a new way to power terrestrial off-grid applications and earth orbiting spacecraft. In 1968, Dr. Peter Glaser published "Power from the Sun: Its Future", which serves as the foundation of this paper to revitalize scientific interest and efforts in this topic. This paper will primarily focus on the reliance of SBS initiatives on reusable launch vehicles (RLV) to place SBS spacecraft in a designated orbit, as well as the technological, economic, and operational challenges associated with power beaming to earth and other spacecraft. This includes a discussion of the variables from the operational environment that contribute or accelerate spacecraft end of life.

In this paper, we use a machine learning method, known as Nonnegative Matrix Factorization, to extract from a given image some new information obtained from a number of color space representations. Such kind of information, termed ``metacolor'', can be considered as a particular color space representation of the image, which can be used to obtain a binary segmentation of the investigated image by distinguishing foreground and background pixels. Some numerical experiments prove that the proposed method shows improved results when compared with common simpler thresholding algorithms.

This article presents the suitability analysis of onshore wind farm sites using an AHP (Hierarchical Analysis Process) multi-criteria decision-making (MCDM) approach based on geographic information system modeling (GIS). This analysis is based on different technical aspects (wind speed, elevation, slope), economic (proximity to the electricity network, proximity to roads) and social (proximity to residential areas, population density). The introduction of the factor “population density” and the constraint “required area” rarely used in previous studies makes it possible to refine the results. The data is classified into several categories in a gradual manner, namely unsuitable (0); less suitable (1); suitable (2); highly suitable (3) and most suitable (4). The results of the study show us that the largest percentage relating to spatial coverage is observed in the “suitable” range with 50.89% and the corresponding TWPP (theoretical wind power potential) is 1377.926 GW; it is followed by “highly suitable” 5.67% and a TWPP of 153.652 GW; then “less suitable” with 1.04% and a TWPP of 28.163GW. No areas were identified in “most suitable” and finally the “unsuitable” range with 42.4%. The results show that the most favorable areas are located in the part of the far north of the country corresponding to the strong wind zone. The sensitivity analysis was carried out based on scenario tests (technical, economic and equal-weight) in order to give greater visibility of choice to the different stakeholders who would like to invest in onshore wind energy in Cameroon. This study is useful in more than one way because the results obtained can help investors, the government and other stakeholders to identify potential areas for the deployment of wind energy systems in Cameroon. Furthermore, a study of hybrid solar-wind systems could improve the efficiency of electricity parks in Cameroon.

In the context of the French tertiary decree, it is crucial to reduce the energy consumption of buildings by first addressing the design of the electrical architecture. Implementing Direct Current (DC) nanogrids in buildings could offers a promising advantage for energy efficiency, significantly impacting overall energy consumption and sustainability goals. For an insulated area with a subtropical climate, such as La Réunion island, DC nanogrids could also facilitate the insertion of local renewable energy sources, especially solar energy. This article presents the deployment and efficiency evaluation of an end-to-end Low Voltage Direct Current (LVDC) nanogrid, from conception to real-world installation within a company. The nanogrid consists of a photovoltaic power plant, a Lithium-Iron-Phosphate (LFP) battery, and DC end-use equipment such as LED lighting and DC fans for two individual offices. An innovation is provided for the power supply and energy management of terminal equipment using the Power Over Ethernet (PoE) standard IEEE 802.3bt. The efficiency of the nanogrid is measured to be 40% higher than the efficiency of an installation powered by PV and distributed at 230 VAC. These results are obtained under certain deployment conditions, which are discussed in this article, in order to enhance the energy efficiency of buildings by using 48VDC. The nanogrid hardware and software infrastructure, the methodology employed for efficiency quantification and the measurement results are described in the paper.

Qualtra, an innovative 10 MW geothermal power plant proposal, employs a closed-loop design to mitigate emissions, ensuring no direct release into the atmosphere. A thorough assessment utilizing energy and exergy analysis, Life Cycle Assessment (LCA), Exergo-economic and Exergo Environmental Analysis (EevA) was conducted. The LCA results, utilizing the ReCiPe 2016 midpoint methodology, encompass all the spectrum of environmental indicators provided. The technology implemented makes it possible to totally avoid direct atmospheric emissions from the Qualtra plant, so the environmental impact is mainly due to indirect emissions over the life cycle. The results obtained for the Global Warming Potential indicator is about 6.6 g CO2/kWh, notably lower compared to other conventional systems. Contribution analysis reveals that the construction phase dominates, accounting for over 90% of the impact in all LCA MidPoint categories. At the component level, a single score calculation incorporating normalization and weighting was executed. The resulting single score is then used into Exergo-Environmental Analysis (EEvA), highlighting the well system as the most impactful contributor, constituting approximately 45% of the total impact. Other substantial contributions to the environmental impact include the condenser (21%), the turbine (17%), and the HEGeo (14%). The Exergo-Economic analysis assesses cost distribution across major plant components, projecting an electricity cost of about 8.3 c€/kWh.

The article presents the issues related to load sharing in direct current grid and a novel control method which has advantages over known solutions. Unlikely of many similar sounding papers this article shows attempt of creation fully controllable non-isolated system which allows load sharing between permanent magnet alternator equipped with machine side converter (MSC) and dual active bridge (DAB) tied to batteries or supercapacitor. The power sharing is essential feature of parallel connected direct current generators and all types of voltage sources in this way are contributing power to the system. Such system should have possibility of the rapid voltage build up in the case of sudden electrical load changes. To keep the optimal efficiency of the alternator the rotational speed changes according to proper mapping of driving combustion engine. When rotational speed is too low then sudden electrical load can cause significant voltage drop and time needed for voltage build up will vary according to RPM increase. In such situations the undervoltage system can trip the breaker and finally there may be a blackout. To avoid such problem the DC systems which consist of batteries and supercapacitor were introduced. System components include a self-excited synchronous generator (SESG) operating at variable shaft speed as well as batteries and supercapacitors that provide electricity for sudden electrical load changes on the distribution grid. The core of presented system is in power distribution method which consists of programmed controllers structure allowing precise currents distribution. A novelty in the proposed method is the use of a cascaded system of current and DC voltage regulators which allows power distribution precise control. In contrary to previously presented solutions, the proposed system allows fast and accurate control of currents loading parallel connected DC voltage sources for wide range generator speed changes. In presented solution both converters have been equipped with Schottky diodes preventing flow of equalizing currents between closed transistors in the parallel mode of operation. An experimental test-stand of the described system is presented with its theoretical basis and experimental results.

The lung microbiota is a complex community of microorganisms that colonize the respiratory tract of individuals from or even before birth. Although the lungs were traditionally believed to be sterile, recent research has shown that there is a diversity of bacterial species in the respiratory system. Knowledge about the lung microbiota in the newborn and its relationship with bacterial infections is of vital importance to understand the pathogenesis of respiratory diseases in neona-tal patients undergoing mechanical ventilation. In this article, the current evidence on the compo-sition of the lung microbiota in the newborn will be reviewed, as well as its role in the develop-ment of bacterial infections in mechanically ventilated neonates. Although advances in many as-pects of the neonatal intensive care unit care have significantly improved the survival of preterm infants, the diagnosis and treatment of ventilator-associated pneumonia has not progressed in recent decades. Avoiding dysbiosis caused by inappropriate use of antibiotics around birth, as well as avoiding intubation of patients or promoting early removal of endotracheal tubes are among the most important preventive measures for ventilator-associated pneumonia. The use of probiotics and prebiotics to prevent infectious, allergic or metabolic complications in the short or long term constitutes a very important field of research in perinatal medicine.

A three-phase multilevel inverter (MLI) synthesized with 31-levels in the output voltage is used to provide ac supply to a three-phase, squirrel-cage induction motor. The gating angles required for thirty power switches in MLI are optimized by both Genetic Algorithm (GA) and Gray Wolf Op-timization (GWO). In the optimization technique, the optimal angles are determined by solving the trigonometric equations from the Fourier analysis for targeting minimum total harmonic distortion (THD) at the MLI output. Simulation model and experimental prototype are developed for performance analysis and validation. The results obtained demonstrate that the MLI is effec-tively able to produce 31-levels of three-phase ac output voltages with THD not exceeding 5% when loaded with a resistive load and a three-phase induction motor. The voltages and currents are measured and recorded for different loads and operating conditions, including the amount of energy consumed by the loads, as well as frequency analysis, which shows the absence of most of the triple harmonics that have a negative impact on the efficiency of the inverter.

This paper is an extended version of a previously reported conference paper regarding low power design for NAND Flash. As the number of bits per NAND Flash die increases with cost scaling, IO datapath speed increases to minimize the page access time with scaled CMOS in IOs. The power supply for IO buffers, namely VDDQ, has decreased from 3V to 1.2V, accordingly. In this paper, how a reduction in VDDQ can contribute to power reduction in BL path is discussed and validated. Conventionally, BL voltage of about 0.5V has been supplied from a supply voltage source (VDD) of 3V. BL path power can be reduced by a factor of VDDQ to VDD when BL voltage is supplied from VDDQ. To maintain a sense margin at sense amplifiers, the supply source for BLs is switched from VDDQ to VDD before sensing. As a result, power reduction and equivalent sense margin can be realized at the same time. The overhead of implementing this operation is an increase in BL access time of about 2% for switching the power supply from VDDQ to VDD and an increase in die size of about 0.01% for adding the switching circuit, both of which are not significant in comparison with a significant power reduction in BL path power of NAND die of about 60%. The BL path was designed in 180nm CMOS to validate the design. When the cost for powering SSD becomes quite significant especially for data center, an additional lower voltage supply such as 0.8V dedicated to BL charging for read and program verify operations may be the best option for the future.

Non-Linear Simulation by Harmonic Balance Techniques of Load Modulated Power Amplifier Driven by Random Modulated Signals. Comparison with measured results.

This research delved into exploring the impact of ladder training on improving the athletic performance of adolescent students, particularly focusing on boosting explosive power and speed. The study involved thirty boys aged 15-17, selected randomly from an Indian school in Doha, Qatar. The variables measured were Explosive Power (EP) and speed (S). EP was assessed using the Standing Broad Jump (SBJ), while Speed (S) was gauged through the 50-yard dash. Divided into two groups - the Experimental Group (EG) and the Control Group (CG), each consisting of fifteen students - the EG underwent dedicated ladder training for 12 weeks while the CG continued their routine. Analysis of pre-test and post-test results indicated significant enhancements in EP and speed within the EG, with notable shifts from 2.15±.27 to 2.40±.24and 7.52±.54to 6.97±.66, respectively, exhibiting significant 't' values (EP: -2.39; speed: 2.23) at P˂.05. Conversely, the CG showed minimal changes in EP (pre: 2.22±.22; post: 2.2±.21) and speed (pre: 7.51±.43; post: 7.58±.72), with 't' values of 0.295 and 0.842, respectively, failing to reach significance at P˂.05. These outcomes highlight the efficacy of ladder training in improving explosive power and speed among adolescent students, suggesting its potential as a safe and advantageous component in athletic training programs.

This article reviews recent innovations in piezoelectric actuators, then indicates the future research targets. In the materials, the piezoelectric performances of relaxor-lead titanate (PZN-PT, PMN-PT) single crystals have been improved significantly by an AC electric poling technique. Also new loss characterization techniques facilitate developing high-power density piezoelectrics. The RMS vibration velocity reaches 0.6 m/s in the k₃₁ mode in lead zirconate titanate (PZT) nowadays, which corresponds to power density 30 W/cm³. Pb-free materials are urged due to the recent political regulation on toxic materials. In device designs, the original multilayer actuators (MLA) with Ag/Pd electrode have been switched to the ones with Cu or pure Ag, in order to suppress the heat generation, then to enhance the device power density. Piezoelectric micro-electro-mechanical-systems (MEMS’s) started to utilize the <1 0 0> oriented epitaxial films of rhombohedral PZT compositions, which exhibits enhanced piezoelectric properties. Also for higher-power applications, aero-sol deposition (AD) methods have been introduced to 10 -thick films. Regarding drive/control techniques in piezo-actuators, three developments are on-going, that is, “negative capacitance” power supplies for driving off-resonance (pseudo-DC) piezo-actuators, capacitive AC power supplies for efficiently driving resonance piezo-actuators, and DC/DC converters for harvesting electric energy from high-impedance piezoelectric devices under noise vibration. The applications of piezoelectric actuators in the 21^st century seem to be oriented toward “politico-engineering” with four keywords, “cooperation, protection, reduction, and continuation”. The sustainability technologies include the following piezoelectric items: (a) Pb-free piezoelectrics, (b) ultrasonic technology for decomposing hazardous materials, (c) reduction of contamination gas, (d) piezoelectric energy harvesting, and (e) device improvement with high energy-efficiency. On the other hand, the following crisis technologies have been developed with piezoelectrics: (a) detection and neutralization technologies of infectious/epidemic diseases such as anthrax, (b) autonomous unmanned underwater, aerial, and land vehicles with piezoelectric actuators, (c) pin-point target weapons, (d) high voltage supplies with piezoelectric transformers, and (e) compact energy sources for remote actuating/sensing systems.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

A facile and environmentally benign method for a single-phase barium titanate synthesis in water vapor medium was studied to reveal the mechanism of phase transformation of the initial simple oxides mixture and estimate the capability of the product to be used as a raw material for low-frequency dielectric ceramics. The composition and structure of the reaction mixture treated in vapor at 130…150 °C as well as 230 °C for various time were investigated by means of XRD, SEM, HRTEM, EDX, and FTIR methods. The kinetics of the occurring phase transformation was described by Johnson-Mehl-Avrami-Erofeev equation. The reaction between the initial oxides was considered as a topochemical process with an apparent activation energy of 74…80 kJ mol^-1. A crucial role in this process belonged to the water vapor medium, which facilitated the generation of the reaction zone and its spreading inward the solid particles. The synthesized tetragonal barium titanate powder (mean particle size of 135 ± 24 nm) was sintered by a conventional technique at 1250 °C to obtain ceramics with grains of about 2 μm. Capacitance measurements performed a dielectric constant and loss tangent of ceramics, which reached 3879 and 6.7 10^-3, respectively, at 1 kHz and room temperature.

This paper aims to explore how climate change affects electricity generation (fossil-fueled power plants, hydroelectric stations, wind systems and photovoltaics) and energy demand in residential buildings in Greece for the period up to 2050. In both cases RCP scenarios results are considered in the appropriate spatial and temporal dimension. Energy supply technologies were examined through statistical regression models and/or mathematical equations correlating climatic parameters with energy productivity. With respect to energy demand, bottom-up models were developed that integrate behavioral and policy aspects. The analysis showed that climate change is expected to mainly affect electricity generation from hydro and thermal power plants, while the impacts on solar and wind energy are significantly lower. The range of impacts on hydro potential and electricity generation depends on the geographical location of the power plants and shows significant uncertainty due to the corresponding uncertainty in climate models estimates regarding precipitation and runoff changes while showing significant geographical variations. With respect to energy demand, climate change is expected to affect energy consumption, but the expected range of effects depends on both the implementation and the characteristics (deep vs. shallow renovation) of measures for upgrading the thermal performance of the building stock and the intensity of climate change.

Modern power systems are confronted with a spread concern on the frequency stability issue due to the widespread integration of randomly fluctuating renewable resources. To address the above concern, this work introduces a load frequency control (LFC) scheme based on a hydrogen based energy-storage unit and a parameter tuning strategy for fractional-order proportional-integral-derivative (FOPID) controller. Firstly, a two-area interconnected power system (IPS) model, including thermal, hydro, solar, wind, gas power generator, and hydrogen based energy-storage unit, is established. Then, a FOPID controller is designed for this IPS model, and an improved gradient-based optimizer (IGBO) is developed to adaptively regulate the parameters of the FOPID controllers. Finally, the effectiveness of the offered LFC scheme are tested through load disturbance and renewable energy fluctuations test scenarios, and provides comparison and robustness analysis among different schemes. The test results validated that the offered LFC scheme can effectively suppress the frequency fluctuations of IPS and has excellent robustness.

Structural health monitoring (SHM) is critical for ensuring the safety of infrastructures like bridges. This article presents a digital twin solution for SHM of railway bridges using low-cost wireless accelerometers and Machine Learning (ML). The system architecture combines edge on-premises computing and cloud analytics to enable efficient real-time monitoring and complete storage of relevant time-history datasets. After train crossings, accelerometers stream raw vibration data, which is processed in the frequency domain and analyzed via machine learning to detect anomalies indicating potential structural issues. The digital twin approach is demonstrated on an in-service railway bridge, where vibration data was collected over two years under normal operating conditions. By learning allowable ranges for vibration patterns, the digital twin model identifies abnormal spectral peaks, suggesting changes in structural integrity. The long-term pilot proves that this affordable SHM system can provide automated and real-time warning of bridge damage and also supports the use of in-house designed sensors of lower-cost and edge computing capabilities than those used in the demonstration. The successful on-premises-cloud hybrid implementation provides a cost effective and scalable model for expanding monitoring to thousands of railway bridges, democratizing SHM to improve safety by avoiding catastrophic failures.

With the economic recession and the deterioration of the ecological environment becoming more and more prominent in the world, the sustainable operation of enterprises is facing the most difficult choice in history. For each responsible enterprise, it is crucial to choose the market power expansive strategy that can improve the realistic viability or the technological innovation strategy that can improve the future development potential. This is of great significance to reduce the negative external effects of the corporate social environment and ensure their sustainable development. In this paper, we select the data of 18 large listed petrochemical companies from 2003 to 2018 as samples and construct a linear regression model for empirical analysis. Meanwhile, we put forward more practical business management strategies for the sustainable development of petrochemical enterprises in developing countries in further research.

The electrical energy supply relies on the satisfactory operation of insulators. The ultrasound recorded from insulators in different conditions has a time series output, which can be used to classify faulty insulators. The random convolutional kernel transform (Rocket) algorithms use convolutional filters to extract various features from time series data. This paper proposes the combination of Rocket algorithms, machine learning classifiers, and empirical mode decomposition (EMD) methods, such as complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN), empirical wavelet transform (EWT), and variational mode decomposition (VMD). The results show that the EMD methods combined with MiniRocket, significantly improve the accuracy of logistic regression in insulator fault diagnosis. The proposed strategy achieves respectively an accuracy of 0.992 using CEEMDAN, 0.995 with EWT, and 0.980 with VMD. These results highlight the potential of incorporating EMD methods in insulator failure detection models to enhance the safety and dependability of power systems.

The capability of in-house transient wave-multibody computational tool of ITU-WAVE are extended to predict the wave power absorption with Wave Energy Converters (WECs) arrays placed in front of a vertical breakwater. The analyses of hydrodynamic exciting and radiation forces are approximated solving boundary integral equation at each time interval. The reflection of incoming waves due to a vertical wall is predicted with method of images. The constructive or destructive performance of WECs arrays with different array configurations is measured with mean interaction factor. The behaviour of the exciting and radiation hydrodynamic forces of each WEC due to a vertical wall effect shows considerable differences than those of WECs arrays without a vertical wall influence. When the wave power absorption with WECs arrays with and without a vertical wall effect are compared, it is shown with numerical experiences that WECs placed in front of a vertical wall have much greater effects on wave power absorption. This can be attribute to the hydrodynamic interaction, standing waves, and nearly trapped waves in the gap between a vertical wall and WECs arrays. The analytical and other numerical results are used to for the validation of the numerical results of the present ITU-WAVE computational tool for exciting and radiation forces, and mean interaction factor of WECs arrays which show satisfactory agreements.

In order to achieve its carbon peak and neutrality targets, a high proportion of distributed power sources are connected to the distribution network in China, which greatly increases the risk of distribution network operation. Aiming at the above problems, this paper proposes an active distribution network risk planning model based on multi-source data from carbon capture and power internet of things, and conducts exceeding testing of distribution network based on the stochastic load flow algorithm with semi-invariant and level expansion, calculates the semi-invariant of each order of node state vectors and branch current vectors, and then utilizes the Gram-Charlier level expansion to obtain the exceeding probability density function and probability distribution function of the node voltages and line powers of the distribution network. The probability density function and probability distribution function of the exceeding are obtained using the Gram-Charlier series expansion. Combined with multi-source data, the active distribution network with integrated energy system considering carbon capture is modeled. According to the risk scenario of the distribution network, the nonconvex constraints in the model are simplified by the second-order cone relaxation, and the optimal planning scheme of the distribution network is solved by combining the gurobi solver with the risk index as the first-level objective and the economic benefit as the second-level objective. The simulation results of a coupled network consisting of a 39-node distribution network and an 11-node transportation network verify the effectiveness of the proposed model.

Low-cost monitors have made possible for the first time measurements of long-term (months to years) potential indoor exposures to fine particles. Indoor and outdoor measurements made over nearly 5 years (2017-2021) by the largest network of low-cost monitors in the United States (PurpleAir) are compared to the prevalence of adult smokers in 1650 Zip codes within the three West Coast states of California, Oregon, and Washington. The results show that mean indoor exposures above the 75th percentile of adult smoking prevalence are more than 50% higher than those below the 25th percentile. Mean outdoor concentrations are also elevated, but by a smaller amount (20%). Both comparisons are significant at the p&lt;0.001 level. The elevation of the PM2.5 concentrations with increasing smoking prevalence is evidence of environmental disparities in income, education, and other socioeconomic indices..

Given the imperative of security, sustainability of supply, strategic considerations, and energy independence, there is a widely acknowledged need to persist in utilizing coal as the primary fuel for electricity generation in power plants. However, in order to combat the rising levels of CO2 in the atmosphere, it is crucial to advance the development of carbon capture and storage (CCS) technologies that enable fossil fuel power plants to achieve zero emissions. These technologies play a pivotal role in capturing and effectively storing CO2, thus ensuring that coal-based power generation can continue while significantly reducing its environmental impact. By implementing CCS solutions, fossil fuel power plants can transition towards a more sustainable and environmentally friendly energy future.The utilization of chemical solvents for CO2 absorption, coupled with long-term storage, presents an intriguing and commercially viable technology for CO2 capture. However, the significant energy demands of the solvent regeneration process necessitate optimization, particularly in large-scale power plants. While the current cost of CO2 capture stands at approximately #55,000.00(Naira) per ton of CO2, the objective is to reduce this cost to below #25,000.00(Naira) per ton of CO2. This reduction in cost is essential to ensure the economic feasibility and widespread adoption of CO2 capture technologies in power generation.This research paper explores various approaches to address the energy demands associated with amine scrubbing integration in a commercial power plant. It provides a comprehensive analysis, both technically and economically, of the performance of these different approaches. While some of the proposed schemes may result in minor efficiency reductions, the key objective is to calculate the specific cost per ton of CO2 captured. The primary focus is on identifying the most suitable configuration to implement large-scale, cost-effective schemes that can serve as a foundation for CO2 capture demonstration projects. By determining the optimal configuration, this research aims to pave the way for the successful implementation of efficient and economically viable CO2 capture technologies in the power generation sector.

a sensorless control scheme based on novel power converging law sliding mode observer is suggested to realize the sensorless control for the permanent magnet synchronous motor (PMSM). Firstly, by introducing a new power converging law, the problem of slow converging speed/large chattering value dilemma in the conventional converging law is solved; Secondly, in view of the shortcomings of the conventional position and speed estimation algorithm, the high-frequency buffeting in the sliding mode observer will be expanded, a phase-locked loop (PLL) velocity and position estimation strategy is adopted to replace it. Finally, through Matlab/Simulink modeling and motor speed regulation platform experimental results, the sensorless position and speed estimation technology proposed in this paper can respond to the starting speed command of 1000 r/min within 0.05 s, and the starting process has no overshoot. When disturbed by 10Nm loading, the speed fluctuation value can be controlled within 1%.

Static voltage stability has become one of the significant risks faced by large-scale renewable energy integration. However, traditional methods for static voltage stability analysis are often overly complex. This paper constructs an equivalent impedance model for renewable energy integrated distribution power systems, proposing a static voltage analysis method for renewable energy integrated distribution power systems based on impedance model index. This method has been verified to be applicable not only to renewable energy single-infeed system but also to multi-infeed system. Furthermore, an analysis is conducted on the influence of the integration capacity, location of renewable energy, and the topology of networks on impedance model index, indicating that a higher impedance model index corresponds to greater static voltage stability margins in the system. Hence, during the planning of renewable energy integration, the plan with the highest impedance model index should be selected. Finally, the accuracy of the analysis methods and conclusions in this paper was validated based on the IEEE 14-node system.

We consider the restrictions on photovoltaic (PV) capacity that are caused by limitations on where panels can be sited, and find quantitative evidence for the need for high efficiencies. We define 15% of the UK’s energy consumption as a “significant” contribution and, with London as an exemplar, we perform an idealised calculation that makes the most optimistic possible assumptions about the capabilities of future PV technologies, and use published surveys of energy usage, dwelling type and insolation. We find that covering every UK domestic roof with the highest power-conversion efficiency (PCE) solar panels currently commercially available, could produce up to 9% of the UK's energy. A 15% contribution would require PV technologies with &gt;37% PCE, more than the theoretical Shockley-Queisser limit. Replacing the idealising assumptions with more realistic estimates increases this by 2-3 times. Alternatively, a solar farm using the currently available PCEs would require a politically challenging ~1200km2 of new land, roughly the area of Greater London, for this 15% contribution. We conclude that PCEs must be driven higher even than the Shockley-Queisser limit for PV to play a significant part in carbon mitigation.

Cooling fans are one of the critical components of air-forced (AF) dry-type transformers for regulating internal temperatures. Therefore, effective malfunction detection is crucial to maintain the transformer temperature within an acceptable range and prevent overheating. Regular maintenance occurs periodically and issues with cooling fans may arise between maintenance periods, leading to prolonged operation under malfunctioning conditions and potential failures. In addition, utilities typically have online information about whether a fan works or not without providing information about cooling fan malfunctioning circumstances. To address these challenges, this study proposes learning-based online monitoring techniques to detect malfunctions in AF transformer cooling fans. Random forests (RFs) and convolutional neural networks (CNNs) are developed to classify the audio signals from cooling fans into normal and malfunctioning classes. Unlike RFs, which require separate feature extraction, CNNs are trained based on spectrogram images derived from audio signals. Thus, various time-frequency techniques are utilized for feature extraction in RFs. Besides, multiple data augmentation techniques are employed to enhance the dataset size and diversity. Algorithmic performance is optimized through hyperparameter tuning and classifier threshold adjustment. Simulations reveal that CNNs outperform RFs, whereas the latter provides superior interpretability of acoustic features compared to the former.

Currently, one of the main focuses of attention in academia is microgrids (MGs) and their ability to maintain stable, resilient, reliable and high–power quality operations. A crucial component in MGs is power converters (PC), which facilitate the decentralization of power generation. This decentralization, however, poses challenges in terms of power quality. This paper presents a microgrid model based on the IEEE 14–bus distribution system and aims to investigate the power quality when the MG operates while connected to the conventional power grid. The MG model has been developed using MATLAB–Simulink®, a specialized tool for electrical engineering simulations. The results obtained are subjected to rigorous analysis and compared with the compatibility levels established by the IEEE–519 standard. This approach allows an accurate assessment of the MGs’ ability to maintain power quality at acceptable levels while interconnected to the conventional power grid. Finally, this study provides a valuable contribution to the MGs’ field of microgrids by providing a detailed and quantitative assessment of power quality, which will aid in the design and optimization of MGs’ for effective implementation in real electric power systems.

This review delves into the critical role of automation and sensor technologies in optimizing parameters for thermal treatments within electricity power generation. The demand for efficient and sustainable power generation has led to a significant reliance on thermal treatments in power plants. However, ensuring precise control over these treatments remains challenging, necessitating the integration of advanced automation and sensor systems. This paper evaluates the pivotal aspects of automation, emphasizing its capacity to streamline operations, enhance safety, and optimize energy efficiency in thermal treatment processes. Additionally, it highlights the indispensable role of sensors in monitoring and regulating crucial parameters such as temperature, pressure, and flow rates. These sensors enable real-time data acquisition, facilitating immediate adjustments to maintain optimal operating conditions and prevent system failures. It explores the recent technological advancements, including machine learning algorithms and IoT integration, which have revolutionized automation and sensor capabilities in thermal treatment control. Incorporating these innovations has significantly improved the precision and adaptability of control systems, resulting in heightened performance and reduced environmental impact. This review underscores the imperative nature of automation and sensor technologies in thermal treatments for electricity power generation, emphasizing their pivotal role in enhancing operational efficiency, ensuring reliability, and advancing sustainability in power generation processes.

Power grid fault diagnosis technology has been widely used at home and abroad. With the access of distributed power sources and diversified loads, the distribution network has changed from a passive network to an active network, and the current has changed from "one-way" to "two-way". The structure of distribution network, equipment environment and operating conditions are becoming more and more complex, and the fault diagnosis and localization of active distribution network is becoming more and more difficult. With the rapid development of artificial intelligence, power grid fault diagnosis based on intelligence is unprecedented. This paper introduces the research status of distributed photovoltaic grid-connected fault diagnosis technology, and expounds the history of fault diagnosis technology, which mainly includes expert system, artificial neural network, Bayesian network, fuzzy set theory, rough set theory, Petri net analytical model and multi-source information fusion, etc. The applicability and characteristics of these diagnoses are described, and the existing defects and the overall direction of improvement are briefly described Finally, the key technical problems and future directions in the field of power system fault diagnosis are pointed out by combining theory with practice, so as to promote the further development of this field.

Recent advancements have revolutionized interplanetary spacecraft missions by combining low-thrust propulsion systems with planetary Gravity-Assist (GA) maneuvers. This study investigates/improved a novel dual-step efficient-robust homotopy algorithm, grounded in indirect optimal control principles, to analyze fuel-optimal bang-bang control problems. The methodology integrates efficient techniques, including the homotopic method, compatible normalization, and improved switching function detection, aimed at enhancing optimal convergence in solving low-thrust gravity-assist spacecraft missions. To illustrate practical application, an Earth-to-Jupiter interplanetary scenario utilizing Mars-GA is examined. Results demonstrate the algorithm's superior efficacy in achieving fuel efficiency, robust convergence, and remarkable accuracy compared to existing solutions.

Contactless charging is evolving fast in many domains and applications such as the electrical vehicles (EV). The principle consists of transferring energy between two systems without having any electrical connection between them. This power transfer can be realized by emitting a magnetic field for Inductive Power Transfer (IPT). In the automotive domain, the application of contactless charging to supply power to the vehicle while driving is one of the solutions envisaged to solve the limited autonomy range of EV and reduced its cost but the system must comply with existing standards (e.g., allocated frequency range and radiated electromagnetic emissions), as summarized in this paper.

This study proposes a methodology for identifying time intervals in which time-of-use (ToU) energy tariffs can be set. This is achieved by analyzing the variability in electric power demand and esti-mating the potential for demand flexibility. The proposed methodology is as follows: first, data preprocessing is performed, focusing on the organization and cleaning of individual consumption records. Subsequently, the data are processed and classified by using consumption variability analysis and clustering techniques. Then, representative clusters are selected and time intervals are analyzed to identify periods of high electric power consumption variability. This methodology was tested with real data from smart meters in the Colombian electrical system, in which time intervals with potential for settinh ToU tariffs were ultimately identified. This work promotes the implementation of demand response strategies that enhance sustainability and facilitate the transition to a more resilient energy landscape both nationally and internationally. The findings are expected to contribute to the formulation of tariff schemes that encourage con-scious changes in electric energy consumption patterns.

In many developing countries of the world including Pakistan motorcycle steeling is one of the main issue that needs to be dealt with an iron hand as it leads to economic losses as well as crime increase in the society, according to the DOWN REPORT there were 28609 motorcycle stolen in 2019 and this number has been increased to 34908 in 2020. Now due to the increasing motorcycles stealing crime what measures can we take to reduce the number of motorcycle theft the rule of technology is enormous in this regards specially information technology (IT) , information technology can play an important role in the security of motorcycles from being theft by the thieves, Information technology provide us the GSM based control system which can be very help full to construct a security system for motorcycle in order to make it antitheft.

Herpes simplex virus type 1 (HSV-1) is a lifelong pathogen characterized by asymptomatic latent infection in the trigeminal ganglia (TG) with periodic outbreaks of cold sores caused by virus reactivation in the TG and subsequent replication in the oral mucosa. While antiviral therapies can provide relief from cold sores, they are unable to eliminate HSV-1. We provide experimental results that highlight non-thermal plasma (NTP) as a new alternative therapy for HSV-1 infection that would resolve cold sores faster and reduce the establishment of latent infection in the TG. Additionally, this study is the first to explore the use of NTP as a therapy that can both treat and prevent human viral infections. We investigated the antiviral effect of NTP using an in vitro model for HSV-1 cold sores, involving the application of NTP from two separate devices to cell-free HSV-1, HSV-1-infected cells, and uninfected cells. We found NTP reduced the infectivity of cell-free HSV-1, reduced viral replication in HSV-1-infected cells, and diminished the susceptibility of uninfected cells to HSV-1 infection. This triad of antiviral mechanisms of action suggest the potential of NTP as a therapeutic agent effective against HSV-1 infection.

Optical current sensors have been developed and improved in recent decades, and their use has been widespread in power systems, including smart grids. Like any measuring instrument or system, the result of its measurements is associated with a measurement uncertainty, which quantifies its precision. This article presents a review of the main uncertainty contributions that affect the quality and performance of optical current sensors.

Clinical work conducted over the last seventeen years at the EEG Institute in Los Angeles and by other neurofeedback providers around the world has demonstrated the utility of extending frequency-based neurofeedback deep into the infra-low frequency (ILF) region, using the method of endogenous neuromodulation described herein. The method is characterized by the absence of any overt reinforcements, which makes it possible to extend the clinical reach to extremely low frequencies. As the training frequency is lowered, the signal becomes more difficult to discriminate, and ultimately it can only be discerned by the brain itself, in the process of endogenous neuromodulation. The method emulates how the brain does skill learning in general: It must observe itself performing the skill, with feedback on its performance. While the immediate target of ILF neurofeedback is enhanced self-regulatory competence--with symptomatic relief and functional recovery the secondary consequences, progressive lowering of the target frequencies has led to improved outcomes in application to challenging dysfunctions such as episodic suicidality, migraine, seizures, and bipolar mood swings. The work has also yielded insights into how the frequency domain is organized. The training proceeds best at frequencies that are specific to each individual, and these are referred to as optimal response frequencies (ORFs). These frequencies differ for various placements but stand in two fixed relationships to one another, one that holds over the EEG spectral range, and another that holds over the entire ILF range. Training in the ILF region engages the dynamics of the glial-neuronal networks, which govern tonic, resting state regulation. The collective clinical experience with ILF neuromodulation within a large practitioner network supports the case for making protocol-based, individualized ‘homeodynamic’ regulation a therapeutic priority, particularly for our most impacted clinical populations: addiction, trauma formations, traumatic brain injury, and the dementias. The case is made for further outcome studies and foundational research.

This scientific paper presents a comprehensive investigation into transient Fourier analysis in some electrical engineering applications. The article deals with two effective approaches for solving transient analysis whose application is rather novel. The first contribution uses combined the Fourier series analytic Laplace-Carson (L­C) transform methods in the complex domain using complex time vectors, thereby significantly simplifying the calculation of the original function. As the inverse transform goes back into the time domain, it employs the Cauchy-Heaviside (C­H) method. The second contribution uses the Fourier transform (F­Τ)for transient analysis of a power converter electrical circuit with the passive and the active load. The method of complex conjugated amplitudes is used for steady-state analysis. Both contributions represent a new approach to this paper. The starting point is the Fourier series/expansions, computation of the Fourier coefficients, then continuing by solving the steady and transient states of the system and confirming the transient states using the Fourier transform. To validate our findings, the worked-out analytical results are verified by modelling in Matlab/Simulink environment.

Background and objectives: Musculoskeletal (MSK) pain significantly impacts physical activity and quality of life in the elderly, potentially influencing mortality. This study explored the relationship between MSK pain, physical activity, muscle mass, and mortality among older adults. Material and Methods: We studied 1000 participants of the Korean Longitudinal Study on Health and Aging (KLoSHA), a prospective, population-based cohort study of people aged 65 years or older. Survival status was tracked over a 5-year period. Correlations between Low back pain (LBP), knee pain, regular exercise, appendicular skeletal muscle mass (ASM), and other variables were analyzed. Logistic regression analyzes were used to identify independent risk factors for mortality. Results: Of the total participants, 829 (82.9%) survived after a 5-year period. Survivors tended to be younger, had a higher BMI, and were more active in regular exercise. In contrast, non-survivors exhibited a higher prevalence of both LBP and knee pain, along with increased instances of multiple MSK pain. Lower ASM correlated moderately with LBP and knee pain, whereas higher ASM was associated with regular exercise Lower ASM was moderately associated with LBP and knee pain, while higher ASM correlated with engagement in regular exercise. There was a moderate correlation between LBP and knee pain, both of which were associated with a lack of regular exercise. Age, sex, ASM, and regular exercise were significant predictors, even though MSK pain itself did not directly predict all-cause mortality. Conclusions: This study demonstrated the independent association between ASM, regular exercise, and mortality. Although MSK pain did not directly correlate with all-cause mortality, the non-survivor group had higher levels of both single and multiple MSK pain. Recognizing the interplay of MSK pain, physical activity, and muscle mass for older adults, the research underscores the need for holistic strategies to enhance health outcomes in older individuals with MSK pain.

We propose Context-aware Feature Transformer Network (CaFTNet), a novel network for human pose estimation. To address the issue of limited modeling of global dependencies in convolutional neural networks, we design Transformerneck to strengthen the expressive power of features. Transformerneck directly substitutes the 3×3 convolution in bottleneck of HRNet with Contextual Transformer (CoT) block, while reducing the complexity of the network. Specifically, CoT first produces keys with static contextual information through 3×3 convolution. Then, relying on the query and contextualization keys, the dynamic contexts are generated through two concatenated 1×1 convolutions. Static and dynamic contexts are eventually fused as an output. Additionally, for the multi-scale networks, in order to further refine the features of the fusion output, we propose an Attention Feature Aggregation Module(AFAM). Technically, given an intermediate input, AFAM successively deduces attention maps along channel and spatial dimensions. Then, Adaptive refinement module(ARM) is exploited to activate the obtained attention maps. Finally, the input undergoes adaptive feature refinement through multiplication with the activated attention maps. Through the above studies, our lightweight network provides a powerful clue for detection of keypoints. Experiments are implemented on the COCO and MPII datasets. The model achieves 76.2 AP on the COCO val2017. Compared to other methods with the CNN as the backbone, CaFTNet reduces the number of parameters by 72.9 %. On the MPII, our method uses only 60.7% of the number of parameters, acquiring semblable results to other methods with the CNN as the backbone.

Through long-term Rayleigh lidar observations during 2010-2022, atmospheric gravity wave (AGW) activities in the middle atmosphere (30–65 km) are statistically investigated at Haikou (110.3°E, 19.9°N) in China. In total, 827 quasi-monochromatic AGW events are identified from the lidar dataset, and the vertical wavelength, observed wave period, and vertical propagation direction of dominant waves are extracted for each AGW event by analyzing the power spectra of wave-induced temperature perturbations. It is revealed that 81.7% of all AGW events were associated with upward-propagating waves, and the proportion of upward-propagating AGWs reached a maximum in autumn and a minimum in winter. The most common vertical wavelengths and wave periods were 6–11 km and 4–10 hours, respectively. In particular, 68 AGW events associated with simultaneous upward and downward propagating waves were observed by lidar, corresponding to 8.2% of the events. The occurrence of such special AGW phenomena is qualitatively discussed, and multiple formation mechanisms may exist. Comparisons are made with previously reported lidar observation results, and the statistical features of AGW activity in the low-latitude middle atmosphere may vary over a relatively wide range depending on the location and altitude. However, a majority of AGWs propagate upward in the middle atmosphere.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

Understanding the evolution patterns in patients diagnosed with acute myeloid leukemia (AML) after therapy is relevant due to the dismal outcome still present in refractory or relapsed AML patients. We performed a retrospective, single-center study to evaluate the mutation profile in paired samples obtained at the time of diagnosis and at the onset of progressive or refractory disease in patients diagnosed with AML through a commercial next-generation sequencing (NGS) panel. In total, 62 patients were analyzed. Of these, 28 patients received ICT, and 34 patients underwent low-intensity treatments. In LIT patients, there were emergent mutations at progressive disease in a 64% (22/34) of the patients. Emergent mutations in the RAS-MAPK signaling pathway were observed in 35.9% (12/34) , corresponding to 54.5% of all patients with emergent mutations (12/22). These were found in 12/22 patients that received venetoclax in combination with hypomethylating agents. Six presented mutations in genes related to the RAS-MAPK pathway. Emerging mutations are frequently observed at progressive AML disease after therapy. In patients treated with LIT, mutations in RAS-MAPK signaling pathway might have a key role on the secondary clinical resistance, not only if they are present at diagnosis, becoming a potential target for the development of new drugs.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

The world population increased from 1 billion in 1800 to around 8 billion today. The Population Division of the United Nations predicts a global population of approximately 10.4 billion people by the end of the century. That represents over 2 billion more people. Moreover, the global community is currently experiencing a precarious state due to the enduring repercussions of the COVID-19 pandemic across all sectors, including energy. Given the rising global population and the limited availability of primary energy resources, we must reach a balance between the demands of a growing human population and the planet’s carrying capacity. The dreadful conflict in Ukraine has precipitated an enormous energy crisis. This crisis served as a warning to the world population of how much they depend on this resource to survive. In France, building sectors (i.e., residential and tertiary) alone consume 45% of the final energy disposable. It is the first energy consumer of the country and one of the most polluting (i.e.; about 34% of CO2 emitted by France). Consequently, we must consider alternative energy resource forms (i.e.; substitution energy forms). Harvesting energy from the building envelope may be a viable technique for partially satisfying the electricity demands of building users. In this context, scientific research offers considerable potential for developing more innovative and efficient systems. This article aims to review the state of the art of advances on the subject to orient and further optimize energy production systems, particularly electricity. This work will address several points of view: Discusses the overall backdrop of the present study and introduces the subject ; details the research strategy and procedures used to produce this paper ; develops state of the art on the potential for generating or recovering power from the building envelope ; presents the SWOT analysis of the earlier-described systems. And finally, it concludes by offering findings and viewpoints.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

The pursuit of more efficient transport has led engineers to develop a wide variety of 1 aircraft configurations with the aim of reducing fuel consumption and emissions. However, these 2 innovative designs introduce significant aeroelastic couplings that can potentially lead to structural 3 failure. Consequently, aeroelastic analysis and optimization has become an integral part of modern 4 aircraft design. In addition, aeroelastic testing of scale models is a critical phase in aircraft devel- 5 opment, requiring accurate prediction of aeroelastic behaviour during scale model construction to 6 reduce costs and mitigate risks associated with full-scale flight testing. Achieving a high degree of 7 similarity between the stiffness, mass distribution and flow field characteristics of scaled models 8 and their full-scale counterparts is of paramount importance. However, achieving similarity is 9 not always straightforward due to the variety of configurations of modern lightweight aircraft, as 10 identical geometry cannot always be directly scaled down. This configuration diversity has a direct 11 impact on the aeroelastic response, necessitating the use of computational aeroelasticity tools and 12 optimization algorithms. This paper presents the development of an aeroelastic scaling framework 13 using multidisciplinary optimization. Specifically, a parametric Finite Element Model (FEM) of the 14 wing is created, incorporating parameterisation of both thickness and geometry, primarily using 15 shell elements. Aerodynamic loads are calculated using the Doublet Lattice Method (DLM) em- 16 ploying twist and camber correction factors, and aeroelastic coupling is established using infinite 17 plate splines. The aeroelastic model is then integrated within an Ant Colony optimization (ACO) 18 algorithm to achieve static and dynamic similarity between the scaled model and the reference wing. 19 A notable contribution of this work is the incorporation of internal geometry parameterisation into 20 the framework, increasing its versatility and effectiveness.

Solar photovoltaic systems (PVs) are becoming more popular in Poland, as the country aims to increase its share of renewable energy sources and reduce its dependence on coal. According to the official data the total installed PV capacity in Poland reached 15.6 GW in September 2023 while at the end of 2020 it was 4.1 GW. This situation was caused by many factors, but mainly by government subsidy programs for households and rising electricity prices. A number of photovoltaic installations with a capacity of up to 50 kWp were carried out, although the installation should always be adapted to the needs of a given household. Estimating the yield of solar energy systems is crucial for that. It can be done by several methods, but always as initial step in modelling of solar energy systems weather data, especially solar irradiation is required. To get this data we can arrange the measurement from ground stations or use reanalysis models and satellite-derived datasets. There are several different datasets, both public and commercial, of solar irradiance data ready to use. This data provides insights into the average solar irradiance levels throughout the year, aiding in estimating the energy generation capacity. The paper contributes the knowledge of energy generation capacity that can be quickly counted for a solar PV micro-system with different orientation and inclination as a multiplier of the energy value obtained from a solar PV system of 1 kW-peak for a significant number of locations in Poland based on open-source solar irradiation data

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

. (1) Background: The aim of this study was to verify the differences in body composition, power and lower limb muscle strength in futsal players from three competitive levels. (2) Methods: The study involved 68 players (24.26 ± 4.63 years), divided into three competitive levels: elite, sub-elite and amateur. To assess physical condition, we used the Inbody270, the ChronoJump and the Isokinetic Dynamometer and used the non-parametric Kruskal-Wallis test to compare the three independent variables. (3) Results: There were no differences in body composition between the players at the three competitive levels. With regard to lower limb muscle power and strength, the elite group showed, on average, better performance and capabilities, especially when compared to the amateur group, and all groups showed an H/Q ratio &gt; 60%. (4) Conclusions: We conclude that there are not many differences in physical condition between the three competitive levels of futsal, despite the unequal sporting demands between them. However, the elite group has greater power and muscle strength, and both groups showed a high probability of lower limb muscle injury at this stage of the sporting season, alerting sports training professionals to the importance of individualized analysis of physical condition and performance capacity.

The present study aimed to evaluate the psychometric properties of the Greek version of the Jefferson Scale of Empathy—Student version (JSE-S) and its association with potential predictors among Greek-speaking undergraduate medical students. This study adopted a cross-sectional, comparative–descriptive research design. The study was conducted during October and November 2023. Cronbach’s α for the JSE-S was 0.846. Cronbach’s α values for the factors “perspective taking”, “compassionate care”, and “standing in the patient’s shoes” were 0.800, 0.715, and 0.748, respectively. The intraclass correlation coefficient for the JSE-S score in the test–retest study was 0.827 (95% CI = 0.647 to 0.915, p-value &lt; 0.001), indicating a high level of reliability. The participants showed moderate empathy levels. Females scored higher than males on the Greek version of the JSE-S (108.8 vs. 102.8, p-value &lt; 0.001). Moreover, students enrolled in the fourth academic year showed higher empathy mean scores than those enrolled in the first year (108.6 vs. 103.6, p-value = 0.012). Statistically significant empathy differences by specialty preferences or faith in God/supreme power were not found. The present study provided satisfactory evidence that the Greek JSE-S is a psychometrically sound measurement instrument. Empathy differences by gender were found in line with prior literature.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

This article is devoted to overcoming the contradiction between the problem of maximizing the extraction of wind energy as the goal of optimizing wind turbines, and the use of traditional methods based on criteria for the aerodynamic quality of the blades. A modified technique is considered in which the optimization criterion is the directly extracted flow power. It is based on pulse theory methods that use specific power as an optimization criterion. A comparative analysis of the energy efficiency of different types of turbines is carried out, and the effects of blade inversion are considered. A method for calculating multi-rotor turbines based on the concept of uniform power distribution is presented. The compatibility of proprietary and traditional methods is considered by comparing the results of numerical experiments with calculated and experimental data from sources. Optimization computational algorithms generate data from numerical experiments and determine optimal parameter configurations for the turbines under consideration. It is shown that orthogonal Darrieus turbines in high-speed mode provide energy efficiency comparable to collinear turbines, and multi-rotor turbines with power uniformly distributed over the working section are not inferior in energy efficiency to basic turbines, with linear blade velocities halved.

It is necessary to manage the power consumption and use fault-tolerance techniques to meet high reliability in Real-Time Embedded Systems, . Hence, in recent years, this is the main reason for providing an ideal approach to decrease power consumption through the worst-case behavior of instantaneous power management (peak-power management), while observing the Thermal Design Power (TDP). Although the multi-core chips in real-time embedded systems provide great opportunity for implementation of Two-phase Triple modular redundancy to meet high reliability, the energy overhead management of concurrently executing tasks is one of the challenges facing designers. In this article, we propose a scheme named Permanent Fault Aware, Two-Phase Peak-Power Management (PFA-TP3M), for scheduling real-time tasks in multi-core systems to eliminate peak power overlap from concurrent running tasks to maintain peak power consumption at the chip TDP. and through mapping different parts of each task on separate cores, prevents consecutive conflicts on cores, which have faced permanent faults to design the fault-tolerant system. Our simulation results show that our proposed scheme provides up to 700x fault tolerance increase (630x on average) compared to the state-of-the-art power management algorithm, an achievement costs up to 14%. (average 11%) increase the length of the task graph compared to it.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

Nutrition and calorie intake are associated with subtle changes of thyroid function tests in subjects with intact Hypothalamic-Pituitary-Thyroid axis. Iodine deficiency and extreme fluctuations in calorie intake, such as those occurring during periods of starvation or overfeeding could lead to alterations of thyroid hormones. The dietary macronutrient composition could also influence the thyroid function. Recently, Low-Glycemic Load (LGL) diets are very popular and effective in the treatment and/or prevention of several medical conditions, including diabetes, obesity, cardiovascular disease, and epilepsy. In this review, we report the available data from the literature regarding the association between LGL diets and thyroid function or dysfunction. Unfortunately, there are only a few studies in this field, with inconsistent findings.