In Electrified Vehicles, the cost, efficiency, and durability of electrified vehicles are dependent on the energy storage system (ESS) components, configuration and its performance. This paper, pursuing a minimal size tactic, describes a methodology for quantitatively and qualitatively investigating the impacts of a full bandwidth load on the ESS in the HEV. However, the methodology can be extended to other electrified vehicles. The full bandwidth load, up to the operating frequency of the electric motor drive (20 kHz), is empirically measured which includes a frequency range beyond the usually covered frequency range by published standard drive cycles (up to 0.5 Hz). The higher frequency band is shown to be more efficiently covered by a Hybrid Energy Storage System (HESS) which in this paper is defined as combination of a high energy density battery, an Ultra-Capacitor (UC), an electrolytic capacitor, and a film capacitor. In this paper, the harmonic and dc currents and voltages are measured through two precision methods and then the results are used to discuss about overall HEV efficiency and durability. More importantly, the impact of the addition of high-band energy storage devices in reduction of power loss during transient events is disclosed through precision measurement based methodology.

Evaluation of the effects of a high-frequency acceleration (HFA) device on patient pain response to orthodontic forces. A multi-centered trial investigating pain sensitivity to orthodontic forces on 75 subjects at 4 study centers. Subjects underwent clear aligner treatment, with or without adjunctive HFA and documented their pain intensity using the validated NRS10 numeric rating scale. In-Office and At-Home ratings were measured separately for each subject for immediate and extended effect evaluations. Use of HFA devices in conjunction with clear aligner orthodontic treatment demonstrated significant reduction in subjects’ recorded pain ratings vs controls within 5 minutes of aligner exchange, (p = 0.006) and significant reduction in recorded pain ratings vs controls over a 7-day period following aligner exchange (p = 0.018). A 99.6% daily compliance rate with at home use of the HFA device was recorded for all subjects in the study. HFA significantly reduces pain attributed to orthodontic force. HFA delivers clinically significant immediate pain relief, and clinically significant extended pain relief over the 7 days following adjustment.

The UK economy is overly reliant on unsustainable production and consumption practices, depleting finite resources at rates that will increase production costs, business risk and economic instability. This over-consumption produces emissions and waste that cause climate change and environmental degradation, impacting on the wellbeing of people in the UK and beyond. The Resource Recovery from Waste programme (RRfW) promotes a transition towards waste and resource management in a circular economy that restores the environment, creates societal benefits and promotes clean growth by engaging relevant actors in the transition process. RRfW collaborates with academia, government, and industry to co-produce a shared vision and approach to realise such a transition. Reflecting insights from RRfW’s government engagement, this article presents a positive outlook for changing the UK economy and society. It envisions a long-term future for waste and resource management that maximises the value of materials by circulating them in the economy for as long as possible. Four themes and an approach are proposed, including recommendations for regulatory instruments and a stable policy framework. It recommends further collaborative research to capitalise on opportunities for economic growth, innovation and resilient infrastructure whilst contributing to quality jobs and welfare in all four UK nations.

The Mediterranean diet (MedDiet) is recognised to reduce risk of coronary heart disease (CHD), in part, via its anti-inflammatory properties. Diet efficacy via this mechanism is however unclear in patients with diagnosed CHD. This study aimed to determine the effect of MedDiet versus low-fat diet intervention on inflammatory biomarkers and adiposity in a pilot cohort of Australian patients post coronary event. Participants (62±9 years, 83% male) were randomised to the MedDiet (n=34) or low-fat diet (n=31). At 0-, 3- and 6-months, dietary counselling, anthropometry, body composition (Dual-energy X-ray Absorptiometry) and venepuncture was conducted. Participants adhered well to the MedDiet intervention, however, there were no significant changes in body composition or inflammatory biomarkers hs-C-reactive protein or hs-interleukin-6 in the MedDiet compared to the low-fat diet group after 6-months. Adiponectin, an anti-inflammatory adipokine, tended to increase in response to the MedDiet (+1.1±4.2ng/mL, p=0.11) and decrease in response to the low-fat diet (-0.9±3.3ng/mL, p=0.20). In the pooled cohort, participants with greatest improvement in MedDiet adherence score had significantly lower waist circumference and subcutaneous fat levels at 6-months. A clinically significant effect of the MedDiet on inflammation and adiposity in CHD patients may require a larger sample, adjunct exercise intervention and/or caloric restriction.

We have successfully measured amyloid beta (Aβ) (1-40) protein added in human serum by a NiCr strain gauge cantilever biosensor immobilized with liposomes incorporating cholesterol. Importantly, we investigated the effect of incorporation of cholesterol in the liposome in order to suppress the interaction between the liposome and many different proteins included in human serum. It was revealed that incorporating cholesterol suppresses the interaction between the proteins other than Aβ in human serum and the liposome. Finally, we detected Aβ(1-40) in human serum with typical chronological behaviors due to Aβ aggregation and fibrillization. Furthermore, as a digital low-pass filtering procedure could reduce external noises, the cantilever sensor immobilized with liposome incorporating cholesterol can detect low-concentrated Aβ in human serum.

Pulsed electric fields of specific frequencies emitted by a glass plasma antenna tube have been shown to slow the growth of Acute Lymphoblastic Leukemia cells by as much as 43% when exposed to a series of frequencies between 156kHz and 162kHz. This narrow band of frequencies is termed a “Destructive Cancer Resonant Frequency Formant” (DCRFF).

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

This paper presents a 612–1152 MHz Injection Locked Frequency Multiplier (ILFM). The proposed ILFM is only used for sending an input signal to the receiver in the I/Q mismatch calibration mode. Using the Phase-Locked Loop (PLL) to calibrate the receiver places a burden on this system due to the extra area required and power consumption. Instead of the PLL, to satisfy high frequency, low jitter, and low area, a Ring Oscillator is proposed. The free-running frequency of the ILFM is automatically digitally calibrated to reflect the frequency of the injected signal from the harmonics of the reference clock. To control the frequency of the ILFM, the load current is digitally tuned with 6-bit digital control signal. The proposed ILFM locks to the target frequency using a digitally controlled Frequency Locked Loop (FLL). This chip is fabricated using 1-poly 6-metal 0.18 µm CMOS and achieve the wide tuning range of 612–1152 MHz. The power consumption is 0.95 mW from a supply voltage of 1.8 V. The measured phase noise of the ILFM is −108 dBc/Hz at a 1 MHz offset.

Findings from studies of prenatal exposure to pesticides and adverse birth outcomes have been equivocal so far. We examined prenatal exposure to agricultural pesticides in relation to preterm birth and term low birthweight, respectively, in children born between 1998 and 2010 randomly selected from California birth records. We estimated residential exposures to agriculturally applied pesticides within 2 km of residential addresses at birth by pregnancy trimester for 17 individual pesticides and 3 chemical classes (organophosphates, pyrethroids, and carbamates). Among maternal addresses located within 2 km of any agricultural pesticide application, we identified 24,693 preterm and 220,297 term births, and 4,412 term low birthweight and 194,732 term normal birthweight infants. First or second trimester exposures to individual pesticides (e.g., glyphosates, paraquat, imidacloprid) or exposures to 2+ pesticides in the three chemical classes were associated with small increases (3-7%) in risk for preterm birth; associations were stronger for female offspring. We did not find associations between term low birthweight and exposures to pesticides other than for myclobutanil (OR: 1.11; 95% CI: 1.04-1.20) and possibly pyrethroids as a class. Our improved exposure assessment revealed that first and second trimester exposures to pesticides were associated with preterm delivery but few affected term low birthweight.

The world is now undergoing through a global emergency due to COVID-19 which needs immediate remedies in order to strengthen the healthcare facility to save the nations. Looking towards to the remedies, research on different aspects including the genomic and proteomic level characterizations of the SARS-CoV2 are necessarily important. In this present study, the spatial representation/composition of twenty amino acids across the primary protein sequences of SARS-CoV2 have been looked into through different parameters viz. Shannon entropy, Hurst exponent in order to fetch the autocorrelation and amount of information over the spatial representations. Also frequency distribution of each of the amino acids over the protein sequences have been chalked out.

Over half of adult Americans now have diabetes or prediabetes and worse, this epidemic is now world-wide and shows no signs of slowing, with rates of both diabetes and diabetes-related health complications still rising. When advising patients with diabetes on food choices, many providers rely on nutrition guidelines provided by the American Diabetes Association (ADA), and these guidelines influence other recommendations across the globe. Given the alarming trends in diabetes, it is paramount to review the treatment guidelines to ensure they are based on rigorous and accepted scientific methods. Our review included the evidence cited by the ADA in support of its claims and recommendations for eating patterns to combat diabetes (see Description of Eating Patterns, Supplemental Appendix), as presented in the most current edition of the annual ADA’s Standards of Medical Care in Diabetes (2018 Standards). Our review also includes sources cited in the latest edition of the ADA’s Nutrition Therapy Recommendations for Adults with Diabetes (2014 Recommendations), which also informed the 2018 Standards. In October 2018 low carbohydrate was named as a recommended eating pattern by the ADA and European Association for the Study of Diabetes (EASD)⁵but only citations from the 2014 and early 2018 ADA documents were reviewed.

We report the results of an analysis of the functional capabilities of the KTP crystal and its isomorphs for nonlinear-optical frequency conversion of all types of interaction in the transparency range of the crystal. The possibility of implementing angle-, wavelength- (frequency-) and temperature-noncritical phase matching is shown.

Crowd counting is of significant importance for numerous applications, e.g., urban security, intelligent surveillance and crowd management. Existing crowd counting methods typically require specialized hardware deployment and strict operating conditions, thereby hindering their widespread deployment. To acquire a more effective crowd counting approach, a device-free counting method based on Channel Status Information (CSI) is proposed, which could mitigate environment noise through wavelet transform and extract the amplitude or phase covariance matrix as the feature vector. Moreover, both the spatial diversity and frequency diversity are leveraged to improve detection robustness. The accuracy of the proposed CSI-based method is compared with a renowned crowd counting one, i.e., Electronic Frog Eye: Counting Crowd Using WiFi (FCC). The experimental results reveal an accuracy improvement of 30% over FCC.

A Twi-English parallel corpus is certainly an important resource for Machine Translation of Twi (ISO 639-3), a Low-Resource African Language (LRAL) which is mainly spoken in Ghana and Ivory Coast. Currently large-scale multi-domain Twi-English parallel corpus is still unavailable partly due to the difficulties and the arduous efforts required in its design. In this paper, we present TWIENG: a large-scale multi-domain Twi-English parallel corpus. We crawled the sentences from the web using web crawlers, translated, aligned, tokenized and compiled to create the corpus. We crawled English sentences from Ghanaian indigenous electronic news portals, Ghanaian Parliamentary Hansards, Twi Bible and crowdsourcing via google forms. The sentences were translated by professional translators and linguists, they were then aligned, tokenized and compiled. The corpus was curated using the sketch engine, a corpus manager and analysis software developed by Lexical Computing Limited. The corpus was manually evaluated by Twi professional linguists. The Corpus has 5,419 parallel sentences.

This paper propose an original approach of achieving a Cymatics based visual perception of isolated speech commands. The idea is to smartly combine the effective speech processing and analysis methods with the phenomena of Cymatics. In this context, an effective approach for automatic isolated speech based message recognition is proposed. The incoming speech segment is enhanced by applying the appropriate pre-emphasis filtering, noise thresholding and zero alignment operations. The Mel-Frequency Cepstral coefficients (MFCCs), Delta coefficients and Delta-Delta coefficients are extracted from the enhanced speech segment. Later on, the Dynamic Time Warping (DTW) technique is employed to compare these extracted features with the reference templates. The comparison outcomes are used to make the classification decision. The classification decision is transformed into a methodical excitation. Finally, this excitation is converted into the systematic visual perceptions via the phenomenon of Cymatics. The system functionality is tested with an experimental setup and results are presented. The approach is novel and can be employed in various applications like visual art, encryption, education, archeology, architecture, integration of impaired people, etc.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

We propose a novel transfer learning method for speech emotion recognition allowing us to obtain promising results when only few training data is available. With as low as 125 examples per emotion class, we were able to reach a higher accuracy than a strong baseline trained on 8 times more data. Our method leverages knowledge contained in pre-trained speech representations extracted from models trained on a more general self-supervised task which doesn’t require human annotations, such as the wav2vec model. We provide detailed insights on the benefits of our approach by varying the training data size, which can help labeling teams to work more efficiently. We compare performance with other popular methods on the IEMOCAP dataset, a well-benchmarked dataset among the Speech Emotion Recognition (SER) research community. Furthermore, we demonstrate that results can be greatly improved by combining acoustic and linguistic knowledge from transfer learning. We align acoustic pre-trained representations with semantic representations from the BERT model through an attention-based recurrent neural network. Performance improves significantly when combining both modalities and scales with the amount of data. When trained on the full IEMOCAP dataset, we reach a new state-of-the-art of 73.9% unweighted accuracy (UA).

A The present investigation was undertaken in foothill regions of Uttarakhand from July-2016 up to December-2018. A total of thirty four different sites ranging from the roadside areas, grasslands to forests were studied and Mushroom fruiting bodies were collected. A total of One Hundred sixty six fruiting counts were obtained and 68 mushroom genera belonging to 15 orders and 43 families were identified. During collection visits mushroom were apparent from organic debris of diversified habitats ranging from humid soil; grassland; leaf litter; living tree trunk; dead wood log of forest zone. Maximum fruiting bodies (75%) were obtained between July to September and minimum i.e. 6% between November – February. Among the collected mushroom Stereum rugosum, Crepidotus variabilis, Laccaria laccata, Schizophyllum commune, Ganoderma applantum, Cantharellus cibarius were more prevalent. Out of all collected mushroom sample the frequency of Mushroom belonging to order Agaricales was 45.18% followed by Polyporales i.e., 27.7%. The collected mushroom were cultured on PDA medium and their mycelial forms were preserved for further studies.

A mechanical ventilation system is a big support for breathing complications, in which an external solution is quite necessary to keep oxygen compensation in the patients. Its knowledge is well widespread and different equipment has been developed. However, they are very expensive and their quantity in medical centers is not sufficient, especially in Peru. Hence, it has been required to develop new methods to provide oxygen by a low cost equipment; Protofy, a research group from Spain, designed one of the first low cost mechanical ventilation systems which was medically validated by its government. In this sense, a redesign of the mechanical ventilation system was carried out according to the local requirements and available technology, a different airbag resuscitator with different properties and geometry, but maintaining its working concept based on a cam compression mechanism. Sensors and a display were added to improve the performance with a control algorithm for the rotation frequency and to show the ventilation curves over time to the medical staff. It was necessary to develop a mathematical model to relate the behavior between ventilation curves for a patient and physical variables of the design, especially in the epidemic COVID 19, that many countries are dealing with at the time research is being conducted. The mechanical ventilation system was redesigned, fabricated, and tested measuring its ventilation curves over time. Results indicate that this redesign provides a sturdy equipment able to work during a longer lifetime than the original. The replicability of the ventilation curves behavior is assured, while the mechanism dimensions are adapted for a particular airbag resuscitator. The mathematical model of the whole system can predict satisfactorily the ventilation curves over time and was used to provide the air pressure, volume, and flow as a function of the rotation angle measured by sensors.

Electric Vehicles (EVs) are increasing the interdependence of transportation policies and the electricity market. EMMEV (Electricity Market Model with Electric Vehicles) is an experimental agent-based model that analyses how carbon reduction policy in transportation may increase number of Electric Vehicles and how does that would influence on the electricity price. Agents are ESCOs (Energy Service Providers) which can distribute fuels and their objective is to maximize their profit. In this paper, EMMEV is used to analyze the impacts of the LCFS (Low Carbon Fuel Standard), a performance-based policy instrument, on electricity prices and EV sales. The agents in EMMEV/regulated parties in LCFS should meet a certain CI (Carbon Intensity) target for their distributed fuel. In case, they cannot meet the target, they should buy credit to compensate for their shortfall and if they exceed, they can sell their excess. The results, considering the assumptions and limitations of the model, show that the banking strategy of the agents contributing in the LCFS might have negative impact on penetration of EVs, unless there is a regular Credit Clearance to trade credits. It is also shown that the electricity price as result of implementing the LCFS and increasing number of EVs has increased between 2–3 percent depending on banking strategy.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

A high proportion of dogs and cats are fearful during veterinary visits, which in some cases may escalate into aggression. Here, we discuss factors that contribute to negative emotions in a veterinary setting and how these can be addressed. The set-up of the waiting area (e.g. spatial dividers; elevated places for cat carriers), tailoring the examination and the treatment to the individual, considerate handling (minimal restraint when possible, avoiding leaning over or cornering animals) and offering high-value food or toys throughout the visit can promote security and, ideally, positive associations. Desensitisation and counterconditioning are highly recommended both to prevent and address existing negative emotions. Some negative experiences such as short-term pain from injections can be minimised by using tactile and cognitive distractions. Preemptive analgesia is recommended for known painful procedures. Recommendations for handling fearful animals to minimise aggressive responses are discussed. However, anxiolytics or sedation should be used whenever there is a risk of traumatising an animal or for safety reasons. Stress-reducing measures can decrease stress and fear in patients and consequently their owners – thus strengthening the relationship with the clients as well as increasing the professional satisfaction of veterinary staff.

In this study, four kinds of animal bone marrow powders were extracted with n-hexane using the Soxhlet extraction method. Polyunsaturated fatty acids were enriched by urea inclusion and low temperature crystallization method, then were further evaluated antioxidant and antibacterial activities. These results showed that the oil composition of the n-hexane extracts of four kinds of animal bone marrow primarily consisted of palmitic acid (18.57–31.01%), stearic acid (3.6–20.95%), and oleic acid (40.22–58.69%). The ratios of saturated fatty acids (SFA)/unsaturated fatty acids (UFA) were 1/1.417, 1/1.327, 1/2.140, and 1.285/1 for sheep, bovine, horse, and camel bone marrow oil, respectively. The SFA/UFA ratios determined by the urea inclusion method were 1/1.518, 1/1.390, 1/2.037, and 1.216/1, respectively. The SFA/UFA ratios according to the low temperature crystallization method with acetone were 1/1.920, 1/2.141, 1/2.360, and 1/1.157 for sheep, bovine, horse, and camel bone marrow oil, respectively. These enrichment methods effected the concentrations of UFAs from the camel bone marrow oil. Among the methods, the low temperature crystallization method effectively enriched the UFAs. All four bone marrow oils exhibited strong antioxidant and antimicrobial activities. The horse bone marrow oil showed the strongest antioxidant activity. Both antioxidant and antimicrobial activity improved after enrichment of the UFAs. These results lay a theoretical basis for application bone marrow oil resources in food and medicine.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Multi-Alignment method coupled with phylogenetic analysis we disclosed the Nsp9 and Nsp10 non-structural proteins of Corona Virus as rRNA RlmH/K methyltransferases with similarities with bin recombinase and int-core integrase fold. Further, Nsp9 has similarities to S8 ribosomal protein and Nap10 has similarity to S10 ribosomal protein. Previously, we showed Nsp13, Nsp14, Nsp15 and Nsp16 are also different types of rRNA RlmE/N and Cfr-like methyltransferases-ribonuclease with RNA helicase domains. Two domains of Nsp13 astonishingly have similarities to ribosomal proteins L6 and L9. Taken together, Nsp9/10 and Nsp13-16 proteins could mimic host ribosome assembly and also could methylate rRNA of mitobibosome preventing mitochondrial protein synthesis and oxidative phosphorylation. Low ATP synthesis causes lowering blood pressure following coma but very ATP concentration (1-10nM) surely induces platelets aggregation through vWA, collagen and GpIIb/IIIa proteins followed by fibrin formation and blood clotting as recently have seen in the lung of many Corona virus infected patients. We have also postulated that two polyproteins itself resemble like 28S and 38S mitoribosome subunits and compete with rRNAs inhibiting the ribosome turnover and new protein synthesis due to their similarities with many ribosomal proteins. Such finding may be valuable in computer-based novel drug design against Corona virus.

Over the past few years, the importance of video surveillance in securing the national critical infrastructure has significantly increased, whose applications include detecting failures and anomalies. Accompanied by video proliferation is the increasing number of attacks against surveillance systems. Among the attacks, false frame injection (FFI) attacks that replay video frames from a previous recording to mask the live feed has the highest impact. While many attempts have been made to detect FFI frames using features from the video feeds, video analysis is computationally too intensive to be deployed on-site for real-time false frame detection. In this paper, we investigate the feasibility of FFI attacks on compromised surveillance systems at the edge and propose an effective technique to detect the injected false video and audio frames by monitoring the surveillance feed using the embedded Electrical Network Frequency (ENF) signals. An ENF operates at a nominal frequency of 60 Hz/50 Hz based on its geographical location and maintains a stable value across the entire power grid interconnection with minor fluctuations. For surveillance system video/audio recordings connected to the power grid, the ENF signals are embedded. The time-varying nature of the ENF component is used as a forensic application for authenticating the surveillance feed. The paper highlights the ENF signal collection from a power grid creating a reference database and ENF extraction from the recordings using conventional short-time Fourier Transform and spectrum detection for robust ENF signal analysis in the presence of noise and interference caused in different harmonics. The experimental results demonstrate the effectiveness of ENF signal detection and/or abnormalities for FFI attacks.

The regulation of hepatic very-low-density lipoprotein (VLDL) secretion plays an important role in the pathogenesis of dyslipidemia and fatty liver diseases. VLDL is controlled by hepatic microsomal triglyceride transfer protein (MTTP). Mttp is regulated by carbohydrate response element binding protein (ChREBP) and small heterodimer partner (SHP). However, it is unclear whether both coordinately regulate Mttp expression and VLDL secretion. Here, adenoviral overexpression of ChREBP and SHP in rat primary hepatocytes induced and suppressed Mttp mRNA, respectively. However, Mttp induction by ChREBP was much more potent than suppression by SHP. Promoter assays of Mttp and the liver type pyruvate kinase gene revealed that SHP and ChREBP did not affect the transactivity of each other. Mttp mRNA and protein levels of Shp^/– mice were similar to those of wild-type; however, those of Chrebp^–/–Shp^–/– and Chrebp^–/– mice were much lower. Consistent with this, the VLDL particle number and VLDL secretion rates in Shp^–/–- mice were similar to wild-type, but were much lower in Chrebp^–/– and Chrebp^–/–Shp^–/–- mice. These findings suggested that ChREBP rather than SHP regulates VLDL secretion and that ChREBP and SHP do not affect the transactivities of each other.

Background: There are major air pollution monitoring gaps in sub-Saharan Africa. Developing capacity in the region to conduct air monitoring in the region can help estimate exposure to air pollution for epidemiology research. The purpose of our study is to develop a land use regression (LUR) model using low-cost air quality sensors developed by a research group in Uganda (AirQo). Methods: Using these low-cost sensors, we collected continuous measurements of fine particulate matter (PM2.5) between May 1, 2019 and February 29, 2020 at 22 monitoring sites across urban municipalities of Uganda. We compared average monthly PM2.5 concentrations from the AirQo sensors with measurements from a BAM-1020 reference monitor operated at the US Embassy in Kampala. Monthly PM2.5 concentrations were used for LUR modeling. We used eight Machine Learning (ML) algorithms and ensemble modeling; using 10-fold cross validation and root mean squared error (RMSE) to evaluate model performance. Results: Monthly PM2.5 concentration was 60.2 µg/m³ (IQR: 45.4-73.0 µg/m³; median= 57.5 µg/m³). For the ML LUR models, RMSE values ranged between 5.43 µg/m³ - 15.43 µg/m³ and explained between 28% and 92% of monthly PM2.5 variability. Generalized additive models explained the largest amount of PM2.5 variability (R²=0.92) and produced the lowest RMSE (5.43 µg/m³) in the held-out test set. The most important predictors of monthly PM2.5 concentrations included monthly precipitation, major roadway density, population density, latitude, greenness, and percentage of households using solid fuels. Conclusion: To our knowledge, ours is the first study to model the spatial distribution of urban air pollution in sub-Saharan Africa using air monitors developed from the region itself. Non-parametric ML for LUR modeling performed with high accuracy for prediction of monthly PM2.5 levels. Our analysis suggests that locally produced low-cost air quality sensors can help build capacity to conduct air pollution epidemiology research in the region.

The term low-resourced has been tossed around in the field of natural language processing to a degree that almost any language that is not English can be called "low-resourced"; sometimes even just for the sake of making a mundane or mediocre paper appear more interesting and insightful. In a field where English is a synonym for language and low-resourced is a synonym for anything not English, calling endangered languages low-resourced is a bit of an overstatement. In this paper, I inspect the relation of the endangered with the low-resourced from my own experiences.

Chronic kidney disease (CKD) affects >10% of the adult population. Each year approximately 120,000 Americans develop end-stage kideny disease and initiate dialysis, which is costly and associated with functional impairments, worse health-related quality of life, and high early-mortality rates exceeding 20% in the first year. Recent declarations by the World Kidney Day and the U.S. Government Executive Order seek to implement strategies that reduce the burden of kidney failure by slowing CKD progression and controlling uremia without dialysis. Pragmatic dietary interventions may have a role in improving CKD outcomes and preventing or delaying dialysis initiation. Evidence suggests that a patient-centered plant-dominant low-protein diet (PLADO) of 0.6-0.8 g/kg/day comprised of >50% plant-based sources, administered by dietitians trained in non-dialysis CKD care, can be promising. The scientific premise of the PLADO is based on the observations that high protein diets with high meat intake are not only associated with higher cardiovascular disease risk but also higher CKD incidence and faster CKD progression due to increased intraglomerular pressure and glomerular hyperfiltration. Meat intake increases production of nitrogenous end-products, worsens uremia, and may increase the risk of hyperkalemia, given constipation from the typical low fiber intake. Plant-dominant, fiber-rich, low-protein diet may lead to favorable alterations in the gut microbiome, which can modulate uremic toxin generation and slow CKD progression, along with reducing cardiovascular risk in CKD patients. PLADO is a heart-healthy, safe, flexible, and feasible diet that could be the centerpiece of a conservative and preservative CKD-management strategy that challenges the prevailing dialysis-centered paradigm.

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

This paper presents the simplified and quick way to obtain an experimental measure of the modulus of elasticity(E) of a piece of metal rod using the Smartphone microphone and through the experimental configuration in mode of unsupport beam Euler-Bernoulli(E-B). To understand it, it is required to have knowledge about flexural vibration of E-B beams and to know the analysis of the spectogram of the audio signal. The methodology consists in measuring the flexural resonance frequency through an app installed on a Smartphone and using the E formula deduced from the E-B theoretical framework. The results of the experimental measurements have a discrepancy of less than 5% with respect to the factory value, for a carbon steel rod with circular cross section using the impact excitation technique. It describes the precision and accuracy of the experimental measurement. It is useful, because it helps to classify the materials in the Faculty of Engineering and it helps to make a more efficient quality control.

Objective: to evaluate the effects of excitatory repetitive transcranial magnetic stimulation (rTMS) of the international 10-20 system P3 point (intraparietal sulcus region) in chronic patients with a frontal lesion and parietal sparing due to stroke on the impaired upper (UL) and lower limb (LL) as measured by Fugl-Meyer Assessment (FMA). Methods: three patients (C1: 49.83/2.75, C2: 53.17/3.83, C3: 63.33/3.08 years-old at stroke/ years post-stroke, respectively) received two weeks (five days/ week) of rTMS at 10 Hz of P3. A patient was treated in similar conditions with a sham coil (S1: 56.58/4.33). No complimentary therapy was delivered during the study. Patients were evaluated before, after- and two months post-treatment (A1, A2 and A3, respectively). Results: we found increased scores for LL in motor function subsection for C1 and C3 and in sensory function for C2 by A2 that remained at A3. We also found an increased score for UL motor function for C2 and C3, but the score decreased by A3 for C2. C3 score for UL range of motion increased by A3 compared to A1 and A2. Conclusion: In a variable way, P3 excitatory rTMS increased FMA scores in different upper and lower limb subsections of our three treated patients.

The COVID-19 pandemic forced the transition to emergency online learning without prior preparation or guidelines. This transition has been particularly challenging in developing countries and low-resource contexts and hindered student engagement. We aim to identify the engagement strategies which students, engaging in emergency online learning in low-resource contexts, perceive to be effective. We conducted a sequential mixed-methods study based on Moore’s interaction framework for distance education. First, we conducted a literature review and interviewed ten teachers and ten students to identify a list of engagement strategies. Then, we designed a questionnaire that examines student perceptions of these strategies. We administered the questionnaire to 313 students engaging in emergency online learning in low-resource contexts. Our analysis results showed that student-content engagement strategies, e.g. screen sharing, summaries, and class recordings, are perceived as the most effective, closely followed by student-teacher strategies, e.g. Q&A sessions and reminders. Student-student strategies, e.g. group chat and collaborative work, are perceived as the least effective. The perceived effectiveness of engagement strategies depends on the context and the students’ characteristics, e.g. gender, major, and technology access. To support instructors, instructional designers, and researchers we propose a ten-level guide for engaging students during emergency online classes in low-resource contexts.

Number of confirmed cases of COVID-19 caused by SARS-CoV-2 exceeded 5 million as of May 21, 2020. Global average of the case fatality rate of COVID-19 is about 7% so far. There exist variations in case fatality rates among countries. Particularly, Singapore and Qatar have exceptionally low case fatality rates with 0.1% while France’s rate is almost 20%. Since no magic bullet treatment for COVID-19 exists, we investigated SARS-CoV-2 strains specific to Singapore in this study to identify a clade with low pathogenicity. Variant analysis revealed that a clade with variants ORF1ab L3606F, A4489V, S2015R, T2016K, and N P13L is common in Singapore. Based on our analysis of variants and historical case statistics, the clade is dominant in a recent surge. Therefore, we suggest that low case fatality rate of Singapore possibly is attributed to the clade. Although contribution of each variant to the low pathogenicity is not clear, L3606F alone does not accomplish such low pathogenicity from the comparison with case fatality data from Japan, where L3606F is dominant. Further investigation is necessary to conclude to validate this finding.

Background: Simulation plays a crucial role in health studies, as it helps medical students apply their theoretical knowledge in real-life situations. Moulage is one of the techniques that helps in making simulation more realistic or high-fidelity. It uses special effects to emulate wounds for a better understanding of what the wound is like visually. Still, moulage is expensive, time-consuming, resource-intensive, and requires the training of staff, which is why we need to find low-cost substitutes for moulage materials. Method: When searching the database “PubMed” for the terms “Low-cost and Medical moulage”, we retrieved 222 studies, out of which when excluding results not related to low-cost, we obtained 62 studies, from which when removing studies that do not contain information regarding moulage, we found two papers, after referring to citations and cited articles of those papers, we ended up with six studies. Based on the selected articles and additional articles sourced from their reference list, a total of 11 studies were included in the review. Results: We understand that moulage is a technique that helps make simulations come alive, but the resources required to use it are at times, expensive, which is why we need to find methods to do low-cost moulage, and many studies address that it can be as simple as using homemade ingredients. Students from a previous study have talked about their opinions regarding the realistic component of moulage and whether if it is any different from other moulages. Most of the students agreed that the moulage ranked well in face and content validity. However, further innovations must be introduced in the field to be widely spread and lead to newer opportunities. Conclusion: Although the research done under moulage is limited, it is accepted that moulage is helpful for simulation-based studies and that low-cost moulage can help make medical studies a better experience for students studying it. Students have a favorable opinion on the realistic aspect of the low-cost moulage applied to them. Newer methods can be introduced to moulage, and it can be implemented in low-income countries.

Taking four of the United Nations Development Goals as reference, this overview describes the need to see from a systemic perspective, the food certifications programs along the food chain in Mexico as today food certifications are voluntary. Using secondary data, the main objectives were: a) there is a fall short in food safety policies and those federal agencies responsible for food safety, to guarantee safe food along the whole domestic food chain, especially in that for low income players; b) the amount of the Mexican Federal Budget Expenses devoted to safety food issues is really low, considering the health, well- being, and food security consequences; and c) due the structural heterogeneity of the Mexican food market, there is a lack of coordination in food regulations along all agents of the food supply chain, bringing to alternate informal markets that put at risk peoples´ health, increasing poverty and inequalities. According to this exercise, only 0.7- 8.7% of producers, 12.5% of supermarkets as well as 42.8% of restaurants would have some type of certifications. Public policies must attend this issue in order to improve food safety and security for the whole population, reducing inequalities, poverty and ensuring them a healthy live.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

Subsurface drainage systems remove excess water from the soil profile thereby improving crop yields in poorly drained farmland. Knowledge of the position of the buried drain lines is important: 1) to improve understanding of leaching and offsite release of nutrients and pesticides, and 2) for the installation of a new set of drain lines between the old ones for enhanced soil water removal efficiency. Traditional methods of drainage mapping involve the use of tile probes and trenching equipment. While these can be effective, they are also time-consuming, labor-intensive, and invasive, thereby entailing an inherent risk of damaging the drainpipes. Non-invasive geophysical soil sensors provide a potential alternative solution. Previous research has focused on the use of time-domain ground penetrating radar (GPR), with variable success depending on local soil and hydrological conditions and the central frequency of the specific equipment employed. The objectives of this study were 1) to test the use of a stepped-frequency continuous wave (SFCW) 3D-GPR (GeoScope Mk IV 3D-Radar with DXG1820 antenna array) for subsurface drainage mapping, and 2) to evaluate the performance of a 3D-GPR with the use of a single-frequency multi-receiver electromagnetic induction (EMI) sensor (DUALEM) in-combination. The 3D-GPR system offers more flexibility for application to different (sub)surface conditions due to the coverage of wide frequency bandwidth. The EMI sensor simultaneously provides information about the apparent electrical conductivity (EC_a) for different soil volumes, corresponding to different depths. This sensor combination was evaluated on twelve different study sites with various soil types with textures ranging from sand to clay till. While the 3-D GPR showed a high success rate in finding the drainpipes at five sites (sandy, sandy loam, loamy sand, and organic topsoils), the results at the other seven sites were less successful due to limited penetration depth (PD) of the 3D-GPR signal. The results suggest that the electrical conductivity estimates produced by the inversion of EC_a data measured by the DUALEM sensor could be a useful proxy to explain the success achieved by the 3D-GPR in finding the drain lines. The high attenuation of electromagnetic waves in highly conductive media limiting the PD of the 3D-GPR can explain the findings obtained in this research.

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.

In Low and Lower-Middle-Income countries, the prevalence of anemia in infancy remains high. In early childhood anemia cause irreversible cognitive deficits and represents a higher risk of child mortality. The consequences of anemia in infancy are a major barrier to overcome poverty traps. The aim of this study was to analyze based on a multi-level approach, different factors associated with anemia in children 6–23 m old based on recent available Standard Demographic Health Surveys (S-DHS). We identified 52 S-DHS that had complete information in all covariates of interest in our analysis between 2005 and 2015. We performed traditional logistic regressions and multilevel logistic regression analyses to study the association between hemoglobin concentrations and household, child, maternal, socio-demographic variables. In our sample, 70 % of the 6–23 m old children were anemic. Child anemia was strongly associated with maternal anemia, household wealth, maternal education and low birth weight. Children fed with fortified foods, potatoes and other tubers had significantly lower rates of anemia. Improving overall household living conditions, increasing maternal education, delaying childbearing and introducing iron rich foods at six months of age may reduce the likelihood of anemia at in toddlerhood.

Selenium-rich Au-Ag mineralization has been discovered in the Kremnica ore district, central Slovakia. The mineralization is hosted by a single quartz-dolomite vein hosted by Neogene propyllitized andesites of the Kremnica stratovolcano. Ore mineralogy and crystal chemistry of individual ore minerals have been studied here. The early base-metal ore mineralization composed of pyrite, sphalerite and chalcopyrite lacks selenium, whereas the superimposed Au-Ag paragenesis is Se-enriched. The Au-Ag alloys, uytenbogaardtite, minerals of the galena-clausthalite series, acanthite-naumannite series, diaphorite, miargyrite, pyrargyrite-proustite, polybasite group, minerals of the tetrahedrite group and andorite branch (andorite IV, andorite VI, Ag-excess fizélyite), freislebenite, and rare Pb-Sb sulphosalts (scaiinite, robinsonite, plagionite) have been identified here. Besides selenides, the most Se-enriched phases are miargyrite, proustite-pyrargyrite, and polybasite-pearceite, whose Se contents are among the highest reported worldwide. In addition, one new phase has been found, corresponding to a Se-analogue of pearceite containing 2.08 - 3.54 apfu Se. The style of mineralization, paragenetic situation, and chemical trends observed in individual minerals are comparable to those of Au-Ag low-sulphidation epithermal Au-Ag mineralizations of the Kremnica and neighboring Štiavnica and Hodruša-Hámre Ore Districts, however, the pronounced enrichment in selenium is a specific feature of the studied vein only.

Indoor air quality and public health have always been an area of prime interest across the globe. The significance of low-cost air quality sensing and indoor public health practices spikes during the time of pandemic and epidemics when indoor air pollution becomes a threat to living beings especially human beings. Indoor diseases are hard to diagnose if they are due to the indoor environmental conditions. A major challenge was observed in establishing a baseline between the indoor air quality sensors and associated diseases. In this work, 10,000+ articles from top literature databases were reviewed using bibliometric analysis to formulate indoor air quality sensors and diseases correlation rubrics to critically review 500+ articles. A set of 200+ articles were selected based on for detailed study based on seven bibliometric indices for publications that used WHO, NIH, US EPA, CDC, and FDA defined principles. This review has been conducted to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies.

Global warming and climate change have led to extreme changes in climatic conditions in recent years. The Taiwan government designates the construction of the Kinmen County as low carbon islands, to promote the operation of 100 electric motorcycles and battery demonstration. This study combined with island tourism, after boarding the island, visitors can rent electric motorcycles from the passenger service center and coordinate with the island tour map to show the location of the battery exchange points, so as to facilitate the search. During the operation, the amount of electric motorcycle lease is 15,551 times, the total mileage of motor vehicle is 284,404 km, the number of battery exchange is 622 times, the lease income is about NT$900,000. To reduce carbon and economic benefits of the assessment, compared to the motorcycles (50 c.c), electric motorcycles (EM 100) can reduce the carbon emissions by 8,726 kg, reducing energy costs of NT$422,594.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

Introduction Color vision deficiency (CVD) constitutes one of the frequently observed eye disorders in all human populations. Color is a prominent sign utilized in the medical profession to study and identify histopathological specimens, lab instruments, and patient examination. Color deficiency affects the medical skills of students resulting in poor clinical examination and color appreciation. There is no effective screening of CVD at any level of the medical profession. Hence, this study was aimed to determine the prevalence of CVD among medical students. Materials and methods This was a cross-sectional study conducted from September 2019 to February 2020 over a period of six months in Karachi, Pakistan. All medical students aged 18-21 years of either gender enrolled in the first and second years of medical college were included in this study. The examination was performed during daylight. Ishihara plates were placed at a distance of 75 cm from the subject and tilted so that the plane of the paper lies perpendicular to the line of vision. Students were given five seconds to read the plate and one examiner was instructed to mark the checklist. A score of less than 12 out of 14 red/green test plates (not including the demonstration plate) was considered as a CVD. All statistical analysis was performed using Statistical Package for Social Sciences version 20.0 (Armonk, NY: IBM Corp). Results The mean age of the medical students was 19.61± 1.22 years. There were (n=123) 53.0% females and (n=111) 47.0% males. Most of the medical students (n=131, 56.0%) belonged to the upper-middle-class socioeconomic group. CVD was observed in (n=13) 6.0%of medical students. Age (p=0.001) and socioeconomic status (p=0.001) were the only demographic factors significantly associated with color deficiency. Conclusions Color deficiency, although an unnoticed concern, is fairly common among medical students. Medical students must be screened for CVD as this will enable them to be aware of their limitations in their future observational skills as a doctor and devise ways of overcoming them in clinical practice.

Dietary approach is essential to obesity control, but the effectiveness of changes in meal frequency (MF) as strategies for loss and maintenance of body mass remain unclear. This study aimed to evaluate the influence of MF on a hypocaloric diet on weight loss, active ghrelin levels and metabolic indicators of women with obesity. This is a randomized, parallel clinical trial, including forty women, randomized in two groups, both following a hypocaloric diet, according to MF (G1 – six meals/day; G2 – three meals/day). Dietary, laboratory, anthropometric and body composition indicators were assessed, as well as energy expenditure (EE), before and after the 90 days of intervention. After intervention, both groups decreased body weight, body mass index (BMI), waist circumference, fat mass (FM), insulin and HOMA-IR. G1 increased insulin sensitivity and G2 reduced triglyceride and FM and increased fat-free mass (FFM). MF increased ghrelin levels. There were no differences in EE variables. Hypocaloric diet with different MF promoted a reduction in total weight, BMI, WC and FM and an improvement in glycidic metabolism. However, the accomplishment of the three meals/day increased the FFM and active ghrelin and reduced triglyceride, while six meals/day was more beneficial in increasing insulin sensitivity.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

Student attendance serves many other important purposes aside from monitoring. In certain universities, the attendance of students in a course is also used as one of the requirements for students to be allowed to sit for the final examination. Traditionally, among most Malaysian Institutions of Higher Learning (IHL), attendance recording is usually done using pen and paper, or uses simple web-based system that is time consuming and difficult for faculty periodic monitoring. To address the identified drawbacks, this research aims to develop a Smart Attendance for Faculty Monitoring System using the Bluetooth Low Energy (BLE) technology to assist faculty in recording, managing and monitoring students’ attendance and class schedules effectively. The system is developed for Android-based devices using an agile methodology consists of iteration and incremental approaches. Thus, to evaluate the effectiveness of the system, a survey was conducted on 140 respondents involving lecturers and students of Kolej Universiti Poly-Tech MARA (KUPTM). Respondents were selected using purposive sampling. The descriptive analysis showed that 87.9% of the respondents strongly agreed that the system is effective in assisting lecturers to record attendance, manage class schedules and student attendance as well as to assist faculty in monitoring students’ absenteeism.

This paper analyses and evaluate the precision and the accuracy the capability of low-cost terrestrial photogrammetry by using many digital cameras to construct a 3D model of an object. To obtain the goal, a building façade has imaged by two inexpensive digital cameras such as Canon and Pentax camera. Bundle adjustment and image processing calculated by using Agisoft PhotScan software. Several factors will be included during this study, different cameras, and control points. Many photogrammetric point clouds will be generated. Their accuracy will be compared with some natural control points which collected by the laser total station of the same building. The cloud to cloud distance will be computed for different comparison 3D models to investigate different variables. The practical field experiment showed a spatial positioning reported by the investigated technique was between 2-4cm in the 3D coordinates of a façade. This accuracy is optimistic since the captured images were processed without any control points.

The tryptophan (TRP)-kynurenine (KYN) metabolic pathway is a main player of TRP metabolism through which more than 95% of TRP is catabolized. The pathway is activated by acute and chronic immune responses leading to a wide range of illnesses including cancer, immune diseases, neurodegenerative diseases, and psychiatric disorders. The TRP-KYN pathway synthesizes multifarious metabolites including oxidants, antioxidants, neurotoxins, neuroprotectants, and immunomodulators. The immunomodulators are known to facilitate the immune system towards a tolerogenic state, resulting in chronic low-grade inflammation (LGI) that is commonly present in obesity, poor nutrition, exposer to chemicals or allergens, prodromal stage of various illnesses, and chronic diseases. KYN, kynurenic acid, xanthurenic acid, and cinnabarinic acid are aryl hydrocarbon receptor ligands that serve as immunomodulators. Furthermore, TRP-KYN pathway enzymes are known to be activated by the stress hormone cortisol and inflammatory cytokines, and genotypic variants were observed to contribute to inflammation and thus various diseases. The tryptophan 2,3-dioxygenase, the indoleamine 2, 3-oxygenases, and the kynurenine-3-monooxygenase are main enzymes in the pathway. This review article discusses the TRP-KYN pathway with special emphasis on its interaction with the immune system and the tolerogenic shift towards chronic LGI and overviews the major symptoms, pro- and anti-inflammatory cytokines, and toxic and protective KYNs to explore the linkage between chronic LGI, KYNs, and major psychiatric, including depressive disorder, bipolar disorder, substance use disorder, post-traumatic stress disorder, schizophrenia, and autism spectrum disorder.

For the elimination of radio-frequency interference (RFI) in a passive microwave radiometer, the threshold level is generally calculated from the mean value and standard deviation. However, a serious problem that can arise is an error in the retrieved brightness temperature from a higher threshold level owing to the presence of RFI. In this paper, we propose a method to detect and mitigate RFI contamination using the threshold level from statistical criteria based on a spectrogram technique. Mean and skewness spectrograms are created from a brightness temperature spectrogram by shifting the 2-D window to discriminate the form of the symmetric distribution as a natural thermal emission signal. From the remaining bins of the mean spectrogram eliminated by RFI-flagged bins in the skewness spectrogram for data captured at 0.1-s intervals, two distribution sides are identically created from the left side of the distribution by changing the standard position of the distribution. Simultaneously, kurtosis calculations from these bins for each symmetric distribution are repeatedly performed to determine the retrieved brightness temperature corresponding to the closest kurtosis value of three. The performance is evaluated using experimental data, and the error in the retrieved brightness temperature is observed to be less than approximately 3 K from a window with a size of 100 × 100 time-frequency bins according to the RFI levels and cases.

The Industrial Internet of Things (IIoT) is bringing evolution with remote monitoring, intelligent analytics, and control of industrial processes. A reference architecture provides the general layout information for the flexible integration of IIoT systems; however, as the industrial world is currently in its initial stage of adopting the full-stack development solutions with IIoT, some challenges need to be addressed. To cope with the rising challenges and provide the blueprint guidelines to develop and implement IIoT in real-time, researchers around the globe have proposed IIoT architectures based on different architectural layers and emerging technologies. In this paper, we first review and compare some widely accepted IIoT reference architectures and present a state-of-the-art review of conceptual and experimental IIoT architectures in literature. We highlight scalability, interoperability, security, privacy, reliability, and low latency as the main IIoT architectural requirements and compare how the current architectures address these challenges. We also highlight the role of emerging technologies in current IIoT architectures to address these requirements and present the literature gap for future research work to address the challenges.

Determination of indoor location based on fine time measurement (FTM) of the round trip time (RTT) of a signal between an initiator (smartphone) and a responder (Wi-Fi access point) enables a number of applications. However, the accuracy currently attainable — standard deviations of 1–2 meter in distance measurement under favorable circumstances — limits the range of possible application. A first responder, for example, may not be able to unequivocally determine on which floor someone in need of help is in a multi-story building. The error in location depends on several factors, including the bandwidth of the RF signal, delay of the signal due to the high relative permittivity of construction materials, and the geometry-dependent “noise gain” of location determination. Errors in distance measurements have unusual properties that are exposed here for the first time. Improvements in accuracy depend on understanding all of these error sources. This paper introduces “frequency diversity,” a method for doubling the accuracy of indoor location determination using weighted averages of measurements with uncorrelated errors obtained in different channels. The properties of this method are verified experimentally with a range of responders. Finally, different ways of using the distance measurements to determine indoor location are discussed and the Bayesian grid update method shown to be more useful than others, given the non- Gaussian nature of the measurement errors.

The signal processing technique is one of the principal tools for diagnosing power quality (PQ) issues in electrical power systems. The Discrete Fourier Transform (DFT) is a frequency analysis technique used to process power system signals and identify PQ problems. However, the DFT algorithm may lead to spectral leakage and picket-fence effect problems for asynchronously sampled signals that contain harmonic, inter-harmonic, and flicker components. To resolve this shortcoming, a hybrid method for frequency estimation based on a second-level DFT approach and a frequency-domain interpolation algorithm to obtain the accurate fundamental frequency of a power system is proposed in this paper. This method uses a second-level DFT to compute the cosine and sine parts for the fundamental frequency components of the acquired signals. Then, a frequency-domain interpolation approach is adopted to determine the amplitude ratio for the cosine and sine parts of the system's fundamental frequency. To demonstrate the performance of the proposed frequency estimation method, the observation window used by this paper to evaluate different estimation algorithms is 200 ms. According to the IEC standards, a 200 ms acquisition window is recommended for power system quality assessment. A set of mixed signals with harmonic, inter-harmonic, and flicker components with the fundamental frequency deviation is used. The evaluation results demonstrate the superiority of the new method over other approaches for assessing asynchronously sampled signals contaminated with noise, harmonic, inter-harmonic, and flicker components.

AbstractWe investigated the effect of cigarette smoking on pathological staging in clinically low-risk patients. Data of 59 patients who were diagnosed with bladder tumor for the first time and had a single lesion radiologically and endoscopically smaller than 3 cm were investigated retrospectively. 33 patients who smoked were classified as Group I, and 26 patients who did not smoke were classified as Group II. Pathological diagnoses of the patients in both groups were compared. The mean age of the patients were 64.8 (20–86) years. In Group II, 5 (19.2%) were female and 21 (80.8%) were male (p < 0.05). Nine patients (27.3%) in Group I and 18 patients (69.2%) in Group II had Ta disease (p < 0.05). Nineteen patients (57.6%) in Group I and 5 patients (19.2%) in Group II had T₁ disease (p < 0.05). The number of patients with low grade (LG) tumor were 8 (24.2%) and 19 (73.1%) in Group I and in Group II, respectively (p < 0.05). The number of patients with high grade(HG) tumor were 25 (75.8%) and 7 (26.9%) in Group I and in Group II, respectively (p < 0.05). TaHG was detected in 9 (27.3%) patients in Group I. In contrast, no patients in Group II had TaHG disease (p < 0.05). The number of patients with T₁HG was 17(51.5%) patients in Group I and 2 (7.69%) patients in Group II (p < 0.05). Smoking is associated with pathologically HG and stage in patients with first time bladder tumor which is single and smaller than 3 cm.

Historical maps constitute unique sources of retrospective geographic information. Recently, several map archives containing map series covering large spatial and temporal extents have been systematically scanned and made available to the public. The geographic information contained in such data archives allows extending geospatial analysis retrospectively beyond the era of digital cartography. However, given the large data volumes of such archives and the low graphical quality of older map sheets, the processes to extract geographic information need to be automated to the highest degree possible. In order to understand the salient characteristics, data quality variation, and potential challenges in large-scale information extraction tasks, preparatory analytical steps are required to efficiently assess spatio-temporal coverage, approximate map content, and spatial accuracy of such georeferenced map archives across different cartographic scales. Such preparatory steps are often neglected or ignored in the map processing literature but represent highly critical phases that lay the foundation for any subsequent computational analysis and recognition. In this contribution we demonstrate how such preparatory analyses can be conducted using classical analytical and cartographic techniques as well as visual-analytical data mining tools originating from machine learning and data science, exemplified for the United States Geological Survey topographic map and Sanborn fire insurance map archives.

Low-frequency electron paramagnetic resonance (EPR) is used to extract the EPR parameter A-mid and support the approximate X-band value of g-mid for Ba(Co_yZn_1/3-yTa_2/3)O₃. Although cobalt hyperfine structure for the [+/−1/2> state is often unresolved at X-band or S-band, it is resolved in measurements on this compound. This allows for detailed analysis of the molecular orbital for the [+/−1/2> state, which is often the ground state. Moreover, this work shows that the EPR parameters for Co substituted into Zn compounds gives important insight into the properties of zinc binding sites.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

Exploiting the linguistic knowledge of the source language for neural machine translation (NMT) has recently achieved impressive performance on many large-scale language pairs. However, since the Turkish→English machine translation task is low-resource and the source-side Turkish is morphologically-rich, there are limited resources of bilingual corpora and linguistic information available to further improve the NMT performance. Focusing on the above issues, we propose a multi-source NMT approach that models the word feature in parallel to external linguistic features by using two separate encoders to explicitly incorporate linguistic knowledge into the NMT model. We extend the word embedding layer of the knowledge-based encoder to accommodate for each word’s linguistic annotations in the context. Moreover, we share all parameters across encoders to enhance the representation ability of the NMT model on the source language. Experimental results show that our proposed approach achieves substantial improvements of up to 2.4 and 1.1 BLEU scores in Turkish→English and English→Turkish machine translation tasks, respectively, which points to a promising way to utilize the source-side linguistic knowledge for the low-resource NMT.

Free vibration analysis of the porous functionally graded circular plates has been presented on the basis of classical plate theory. The three defined coupled equations of motion of the porous functionally graded circular/annular plate were decoupled to one differential equation of free transverse vibrations of plate. The one universal general solution was obtained as linear combination of the multiparametric special functions for the functionally graded circular and annular plates with even and uneven porosity distributions. The multiparametric frequency equations of functionally graded porous circular plate with diverse boundary conditions were obtained in the exact closed-form. The influences of the even and uneven distributions of porosity, power-law index, diverse boundary conditions and the negligibled effect of the coupling in-plane and transverse displacements on the dimensionless frequencies of the circular plate were comprehensively studied for the first time. The formulated boundary value problem, the exact method of solution and the numerical results for the perfect and imperfect functionally graded circular plates have not yet been reported.

The effect of filling velocity on positive macrosegregations in large size steel ingots was studied. Macrosegregation and macro-/micro-structure were characterized on the hot-tops and a portion of the upper section of two ingots. The measurements revealed that segregation features in the two ingots varied as a function of the alloying elements, and that the severity of positive macrosegregation in the casting body was reduced when the filling rate was increased. It was also found that at the higher filling rate, grain morphologies in the first solidified zones of the ingot changed from columnar to equiaxe, and secondary dendrite arm spacing (SDAS) became slightly smaller in the intermediate and final solidified zones. The experimental findings were analyzed in the framework of diffusion and convection controlled solidification, as well as liquid metal flow theories. The solute dependence of segregation features was related to the difference in solid-liquid partition coefficient and diffusion capability of each element in the liquid iron. Calculation of Reynolds numbers (Re) during the filling process, for both ingots, showed that higher filling velocity caused more instable movement of the liquid metal in the initial solidification stage, resulting in the modification of grain morphology, as well as accelerated solidification rate.

This paper is a mini literature review about electromagnetic field’s effects on cells, tissues and new treatment modalities. We have reviewed a papers which have been published in high quality journals in the last 5 years as two authors. This review’s aim is to be a resource for experimental studies about electricity’s effects on cell biology and pathophysiology. As a result of this literature review, we found that especially extremely low electric frequency and intermediate frequency fields have very important pathophysiological effects. We have mentioned four important expressions on this subject; electroporation, electrofusion, electrochemotherapy, gene electrotransference. Two different new treatment approaches have been developed by use of these two important electrical waves. First is tumor treating fields and the other is pulsed electric fields. Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma multiforme and malign melanoma.Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma and melanoma.

This letter introduces a frequency response characteristic (FRC) curve and its application in high renewable power systems. In addition, the letter presents a method for fast frequency response assessment and frequency nadir prediction without performing dynamic simulations using detailed models. The proposed FRC curve and fast frequency response assessment method are useful for operators to understand frequency response performance of high renewable systems in real time.

Low carbon cities are increasingly forming a distinct strand of sustainability literature. Models have been developed to measure the performance of low carbon cities. The purpose of this paper is to formulate a strategy-based model to evaluate current performance and predict future conditions of low carbon cities. It examines the dynamic interrelationships between key performance indicators (KPIs), induces changes to city plan targets and then instantly predicts the outcome of these changes. Designed generic and flexible, the proposed model shows how low carbon targets could be used to guide the transformation of low carbon cities under four strategies: (1) passive intervention, (2) problem solving, (3) trend modifying and (4) opportunity seeking. Further, the model has been applied to 17 cities and then tested on 5 cities: London, New York, Barcelona, Dubai and Istanbul. The paper concludes with policy implications to realign city plans and support low carbon innovation.

In this paper, we draw on recent experiences from the Young Lives study to discuss some of the ethical and practical challenges facing longitudinal cohort studies in low- and middle-income countries in the time of coronavirus. We argue that COVID-19 has instigated an ‘ethics of disruption’ for social researchers across the world, and for longitudinal cohort studies like Young Lives, this requires navigating three core considerations: first, managing research relationships and reciprocity within an observational study design; second, maintaining methodological continuity and consistency across time; and third, balancing an immediate short-term response to COVID-19 against the longer-term perspective. We refer to the study’s plan to implement a new COVID-19 phone survey to illustrate how the team are navigating this altered ethical terrain.

Chronic pain is a serious health concern and potentially debilitating condition, leading to anxiety, depression, reduced productivity and functionality, and poor quality of life. This condition can be even more detrimental and incapacitating in the pediatric patient population. In low and middle income countries (LMICs), pain services are inadequate or unavailable, leaving most of the world's pediatric population with chronic pain untreated. Many of these children in LMICs are suffering without treatment, and often die in pain. Awareness and advocacy for this population must be prioritized. We reviewed the available literature on the chronic pediatric pain burden in LMICs, barriers to treatments, and current efforts to treat these patients.

How perceptual limits can be overcome has long been examined by psychologists. This study investigated whether visual cues, blindfolding, visual-auditory synesthetic experience and music training could facilitate a smaller frequency difference limen (FDL) in a gliding frequency discrimination test. It was hoped that the auditory limits could be overcome through visual facilitation, visual deprivation, involuntary cross-modal sensory experience or music practice. Ninety university students, with no visual or auditory impairment, were recruited for this one-between (blindfold/visual cue) and one-within (control/experimental session) designed study. A MATLAB program was prepared to test their FDL by an alternative forced-choice task (gliding upwards/gliding downwards/no change) and two questionnaires (Vividness of Mental Imagery Questionnaire & Projector-Associator Test) were used to assess their tendency to synesthesia. Participants with music training showed a significantly smaller FDL; on the other hand, being blindfolded, being provided with visual cues or having synesthetic experience before could not significantly reduce the FDL. However, the result showed a trend of reduced FDLs through blindfolding. This indicated that visual deprivation might slightly expand the limits in auditory perception. Overall, current study suggests that the inter-sensory perception can be enhanced through training but not though reallocating cognitive resources to certain modalities. Future studies are recommended to verify the effects of music practice on other perceptual limits.

Recent advance in electric propulsion systems have demonstrated that these engines can be used for for long-duration interplanetary voyages. Constant specific impulse engine described as a thrust-limited engine is an example of this type of engine, processing the ability to operate at a constant level of impulse. The determination of minimum-fuel, planar heliocentric Earth-to-Mars low-thrust trajectories of spacecraft using a constant specific impulse is discussed considering the first-order necessary conditions derived from Lawden’s primer vector theory. The minimum-fuel low-thrust Earth-to-Mars optimization problem is then solved in two-dimensional, heliocentric frame using both indirect and direct methods. In the indirect method, two-point-boundary-value problems are derived to solve boundary value problems for ordinary differential equations. In the direct method, a general-purpose optimal control software called GPOPS-II is adopted to solve these optimal control problems. Numerical examples using two different optimization methods are presented to demonstrate the characteristics of minimum-fuel planar low-thrust trajectories with on-off-on thrust sequences at three chosen flight times and available maximum powers. The results are useful for broad trajectory search in the preliminary phase of mission designs.

Identifying group movement patterns of crowds and understanding group behaviors is valuable for urban planners, especially when the groups are special such as tourist groups. In this paper, we present a framework to discover tourist groups and investigate the tourist behaviors using mobile phone call detail records (CDRs). Unlike GPS data, CDRs are relatively poor in spatial resolution with low sampling rates, which makes it a big challenge to identify group members from thousands of tourists. Moreover, since touristic trips are not on a regular basis, no historical data of the specific group can be used to reduce the uncertainty of trajectories. To address such challenges, we propose a method called group movement pattern mining based on similarity (GMPMS) to discover tourist groups. To avoid large amounts of trajectory similarity measurements, snapshots of the trajectories are firstly generated to extract candidate groups containing co-occurring tourists. Then, considering that different groups may follow the same itineraries, additional traveling behavioral features are defined to identify the group members. Finally, with Hainan province as an example, we provide a number of interesting insights of travel behaviors of group tours as well as individual tours, which will be helpful for tourism planning and management.

This research aims to estimate the micro-motion (m-m) of ships. The problem of motion and m-m detection of targets is usually solved using synthetic aperture radar (SAR) along-track interferometry (ATI) which is observed employing two radars spatially distanced by a baseline extended in the azimuth direction. This paper is proposing a new approach where the m-m estimation of ships, occupying thousands of pixels, is measured processing the information given by sub-pixel tracking generated during the coregistration process of several re-synthesized time-domain and overlapped sub-apertures. The SAR products are generated splitting the raw data, according to a small-temporal baseline strategy, observed by one single wide-band staring spotlight (ST) SAR image. The predominant vibrational modes of different ships are estimated and results are promising to extend this application in performing surveillance also of land-based industries activities. Experiments are performed processing one ST SAR image observed by the COSMO-SkyMed satellite system.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

The coronavirus disease 2019 (COVID-19) has spread over the world for more than one year. COVID-19 often develops life-threatening hypoxemia. Endothelial injury caused by the viral infection leads to intravascular coagulation and ventilation-perfusion mismatch. However, besides above pathogenic mechanisms, the role of alveolar edema in the disease progression has not been discussed comprehensively. Since the exudation of pulmonary edema fluid was extremely serious in COVID-19 patients, we bring out a hypothesis that severity of alveolar edema may determine the size of poorly-ventilated area and the blood oxygen content. Treatments to pulmonary edema (alcohol-oxygen vapor therapy and fluid management) may be great helpful for reducing occurrence of severe cases. Given that late mechanical ventilation may cause mucus (edema fluid) to be blown to the deep of the small airways, oxygen therapy should be given at the early stages. The optimal time and SpO₂ threshold for oxygen therapy are also discussed.

Background: Variations in several clopidogrel-pharmacogenes have been linked to clopidogrel response variability and clinical outcomes. We aimed to determine the frequency distribution of major polymorphisms on CYP2C19, PON1, ABCB1 and P2RY12 pharmacogenes in Puerto Ricans. Methods: This was a cross-sectional, population-based study of 200 unrelated “Guthrie” cards specimens from newborns registered in the Puerto Rican Newborn Screening program (PRNSP) between 2004 and 2014. Taqman® SNP assay techniques were used for genotyping. Results: Minor Allele Frequencies (MAF) were 46% for PON1 (rs662), 41% for ABCB1 (rs1045642), 14% for CYP2C19*17, 13% for CYP2C19*2, 12% for P2RY12-H2 and 0.3% for CYP2C19*4. No carriers of the CYP2C19*3 variants were detected. All alleles and genotype proportions were found to be in Hardy-Weinberg equilibrium (HWE). Overall, there were no significant differences between MAFs of these variants in Puerto Ricans and the general population (n=453) of the 1,000 Genome project, except for the Yoruba in Ibadan from Nigeria (YRI, West-African ancestry; p<0.05). As expected, the prevalence of these markers in Puerto Ricans most resembled those in the 181 subjects from reference populations of the Americas. Conclusions: These prevalence data provide a necessary groundwork for future clinical studies of clopidogrel pharmacogenetics in Caribbean Hispanics.

The consumer’s acceptability of hamburgers elaborated with the flank of culling cows in which the content of salt or fat had been partially replaced was studied. A mixture of potassium chloride, potassium ferrocyanide and sodium ferrocyanide was used as substitutes for the salt. Oat flakes or a mixture of chia and flax seeds were used as substitutes for the fat. The hamburgers were tasted by 34 consumers. Consumers did not detect significant differences between the control and the rest of the formulations. Neither the gender nor the age of the consumers influenced the sensory appraisal. However, many comments regarding texture failures were recorded. Therefore, the substitution of salt and / or fat in the composition of hamburgers made with the flank of cows is a viable alternative for the commercialization of these pieces of low commercial value as long as the texture of the same is adjusted to resemble it to the control.

Time is a component quantity of various measurements and is also used on its own to sequence events, to compare the duration of events or the intervals between them, and to quantify rates of change of quantities in material reality or in the conscious experience [1]. The measuring equipment well might happen to be a clock. By making a presupposition that clock is Time, it is perceived experimentally that “Time exhibits wave-like properties”

Based on the theory of turbulence, equations are derived for estimations of turbulent fluctuations of the longitudinal and transverse components of the wind velocity during ideal hovering of a quadcopter in a turbulent atmosphere. We present the results of experiments which were carried out on the territory of the Geophysical Observatory of Institute of Monitoring of Climatic and Ecological Systems, Siberian Branch, Russian Academy of Sciences, located in Tomsk Akademgorodok on the territory with complex orography, in a parkland zone with buildings of research institutes and motorways. Time series of turbulent fluctuations of the longitudinal and transverse components of wind velocity fluctuations were received with the use of an automated weather station, and time series of estimates of these components, from data of a DJI Phantom 4 Pro quadcopter during hovering. According to the automated weather station data, anisotropy was observed in one experiment during measurements in the atmosphere, but this phenomenon was not observed in the other experiment: the fluctuation spectra of all components of wind speed fluctuations coincide. The spectra of fluctuations of the longitudinal and transverse wind velocity components based on the automated weather station data and UAV telemetry are presented. The fluctuation spectra of these components for the automated weather station data and quadcopter generally coincide. The behavior of the spectra coincides with the spectrum which corresponds to Kolmogorov–Obukhov “–5/3” law within the inertial range. The turbulent spectra of the wind velocity fluctuations obtained with the use of the automatic weather station and with the unmanned aerial vehicle differ in the high-frequency spectral region.

This paper focuses on the non-destructive dielectric measurement for low-loss planar materials with a thickness of less than 3 mm using a large coaxial probe with an outer diameter of 48 mm. The aperture probe calibration procedure required only to make a measurement of the half-space air and three offset shorts. The reflection coefficient for the thin material is measured using a Keysight E5071C network analyzer from 0.3 MHz to 650 MHz and then converted to a relative dielectric constant and tangent loss via closed form capacitance model and lift-off calibration process. Measurement error of dielectric constant, Δε_r is less than 2.5 % from 1 MHz to 400 MHz and the resolution of loss tangent, tan δ measurement is capable of achieving 3×10^-3.

Carbon farming is a capable strategy for more sustainable production of food and other related products. It seeks to produce the diverse array of natural farming methods and marketable products simultaneously. In agroforestry system, carbon sequestration is done by incorporating carbon dioxide (CO2) into plant biomass via photosynthesis. Carbon is, thus, stored in reserves of above-ground biomass, such as timber or branches, and below-ground biomass such as roots, or organic carbon in the soil. In addition to the significance of carbon sequestration in climate change mitigation, soil organic carbon (SOC) is an imperative indicator for the soil health as well as fertility. The change in SOC can explain whether the land use pattern degrades or improves the soil fertility. SOC, found in the soil in the form of soil organic matter (SOM), helps to improve soil health either directly or indirectly. Its direct consequence is related to the process of mineralization. Further, agroforestry is highly capable of generating huge amounts of bio-mass. In fact, agroforestry is believed to be particularly suitable for replenishment of SOC. Therefore, efforts should be made to convince farmers for their resource-use efficiency and soil conserving ability in order to get maximum benefits out of agriculture. According to food and agriculture organization (FAO,) agriculture, forestry, and other land use practices account for 24% of global greenhouse gas (GHG) emissions, and total global livestock emissions of 7.1 gigatons of CO2-equivalent per year, representing 14.5% of total anthropogenic GHG emissions. Agroforestry system that deliberately integrates trees and crops with livestock in the agricultural production could potentially increase carbon sequestration and decrease GHG emission from the terrestrial ecosystems, thus, helping in global climatic change mitigation. This study, therefore, aimed at clarification about carbon farming, modifications in carbon cycle and carbon sequestration during agricultural development in addition to benefits of agroforestry.

Adaptive Sliceable-Bandwidth Variable Transceivers (S-BVTs) are key enabler for future optical networks. In particular, those based on Discrete MultiTone (DMT) modulation and Direct Detection (DD) can be considered a flexible solution suitable to address the cost efficiency requirement of optical metro networks. In this paper, we propose to use this cost-effective S-BVT option/implementation in optical metro networks adopting switching nodes based on Semiconductor Optical Amplifier (SOA) technology. Bit loading (BL) and power loading (PL) algorithms are applied to the Digital Signal Processing (DSP) modules, to maximize the performance and/or the capacity as well as enhance the flexibility and adaptability of the system. Our analysis considers switching nodes based on SOAs with and without filtering elements and fiber spans of 25 km. We present the results up to 100 km, with and without SOA-based nodes. Firstly, we analyze the adaptive BVT transmission using the Margin Adaptive (MA) BL/PL algorithm at a fixed bit rate of 28 Gb/s. The possibility of controlling the SOAs current is a key factor to face the transmission impairments due to the fiber and the filtering elements. We also analyze the system considering Rate Adaptive (RA) transmission at a fixed target BER of 3.8·10⁻³, showing that a maximum capacity above 34 Gb/s can be achieved for a single span of 25 km. Although the cascading of filtering elements still constitutes a limiting factor, we show that an improvement of the net bit rate performance can be obtained thanks to the combined use of S-BVT and SOA technology at the switching nodes, resulting in a promising approach for designing future optical metro networks.

The principal aim of a spectral observer is twofold: the reconstruction of a signal of time via state estimation and the decomposition of such a signal into the frequencies that make it up. A spectral observer can be catalogued as an online algorithm for time-frequency analysis because is a method that can compute on the fly the Fourier transform (FT) of a signal, without having the entire signal available from the start. In this regard, this paper presents a novel spectral observer with an adjustable constant gain for reconstructing a given signal by means of the recursive identification of the coefficients of a Fourier series. The reconstruction or estimation of a signal in the context of this work means to find the coefficients of a linear combination of sines a cosines that fits a signal such that it can be reproduced. The design procedure of the spectral observer is presented along with the following applications: (1) the reconstruction of a simple periodical signal, (2) the approximation of both a square and a triangular signal, (3) the edge detection in signals by using the Fourier coefficients, (4) the fitting of the historical Bitcoin market data from 2014-12-01 to 2018-01-08 and (5) the estimation of a input force acting upon a Duffing oscillator. To round out this paper, we present a detailed discussion about the results of the applications as well as a comparative analysis of the proposed spectral observer vis-à-vis the Short Time Fourier Transform (STFT), which is a well-known method for time-frequency analysis.

Confidence interval of is an interval corresponding to a specified confidence and including the true value. It can be used to describe the precision of a statistical quantity and quantify its uncertainty. Although the principle of maximum entropy (POME) has been used for a variety of applications in hydrology, the confidence intervals of the POME quantile estimators have not been available. In this study, the calculation formulas of asymptotic variances and confidence intervals of quantiles based on POME for Gamma, Pearson type 3 (P3) and Extreme value type 1 (EV1) distributions were derived. Monte Carlo Simulation experiments were performed to evaluate the performance of derived formulas for finite samples. Using four data sets for annual precipitation at the Weihe River basin in China, the derived formulas were applied for calculating the variances and confidence intervals of precipitation quantiles for different return periods and the results were compared with those of the methods of moments (MOM) and of maximum likelihood (ML) method. It is shown that POME yields the smallest standard errors and the narrowest confidence intervals of quantile estimators among the three methods, and can reduce the uncertainty of quantile estimators

Advanced image processing will be crucial for emerging technologies such as autonomous driving, where the requirement to quickly recognize and classify objects under rapidly changing, poor visibility environments in real time will be needed. Photonic technologies will be key for next-generation signal and information processing, due to their wide bandwidths of 10’s of Terahertz and versatility. Here, we demonstrate broadband real time analog image and video processing with an ultrahigh bandwidth photonic processor that is highly versatile and reconfigurable. It is capable of massively parallel processing over 10,000 video signals simultaneously in real time, performing key functions needed for object recognition, such as edge enhancement and detection. Our system, based on a soliton crystal Kerr optical micro-comb with a 49GHz spacing with >90 wavelengths in the C-band, is highly versatile, performing different functions without changing the physical hardware. These results highlight the potential for photonic processing based on Kerr microcombs for chip-scale fully programmable high-speed real time video processing for next generation technologies.

The purpose of this study was to present the challenges faced when implementing a diet and exercise intervention for low-income older Hispanics with type 2 diabetes with an observational study of recruitment, attendance, and characteristics of Hispanic adults with type 2 diabetes in a community congregate meal site pre and post administration of a diet and exercise intervention. This report evaluates retentions and diabetes self-management beliefs Hispanic adults ≥60 years with type 2 diabetes (n=17) at baseline, and completion of the six-month intervention in terms of the Health Belief Model. There was limited interest in controlling diabetes with diet and exercise. Major barriers included lack of perceived vulnerability to diabetes complications and a belief that medication alone is sufficient to stabilize blood glucose. Environmental barriers included lack of transportation, access to exercise groups, access grocery stores, and limited ability to pay for healthy foods. A lesson learned from this intervention was that the diet and exercise intervention given was insufficient as a cue to action for this population interventions to engage low-income, older Hispanics with diabetes in diet and exercise need to consider strategies to overcome barriers such as health beliefs, transportation issues, lack of access to nutritious food and group exercise classes.

Although commercially-available low-cost air quality sensors have low accuracy, the sensor system are being used to collect the data for the regulation of PM2.5 emission caused by industrial activities or to estimate the personal exposure for PM2.5. In this work, to solve the accuracy problem of low-cost PM sensor, we developed a new PM2.5 calibration model by combining the deep neural network (DNN) optimized in calibration problem and a LSTM optimized in time-dependent characteristics. First, two datasets were generated to test the accuracy performance and generalization performance of the PM2.5 calibration machine learning (ML) model. The PM2.5 concentrations, temperature and humidity by low-cost sensor and gravimetric-based PM2.5 measuring instrument were sampled for a sufficiently long time. The proposed model was compared with benchmark (multiple linear regression model) and low-cost sensor results. For root mean square error (RMSE) for PM2.5 concentrations, the proposed model reduced 41-60% of error compared to the raw data of low-cost sensor, and reduced 30-51% of error compared to the benchmark model. R2 of ML model, MLR and raw data were 93, 80 and 59 %. Also, the developed model still showed consistent calibration performance when calibrated with new sensors in different locations. Low-cost sensors combined with ML model not only can improve the calibration performance of benchmark, but also can be applied to the sensor monitoring systems for various epidemiologic investigations and regulatory decisions.

(1) Background: Although manual therapy for pain relief has been used as an adjunct in treatments for chronic low back pain (CLBP), there is still the belief that a single session of myofascial release would be effective. This study aimed to investigate whether a single session of a specific technique reduces pain and disability. (2) Methods: This was a crossover clinical trial in which 41 participants over 18 years old with CLBP were randomly enrolled into 3 situations - experimental, placebo, control, in a balanced and cross-over manner. The subjects underwent a single session of myofascial release on thoracolumbar fascia and compare it with the control and placebo. Outcome were pain and functionality, evaluated using the numerical pain rating scale (NPRS), pressure pain threshold (PPT) and Oswestry (ODI). (3) Results: There was no effects between-, within-tests, and interaction for all the outcomes, i.e., NPRS (η 2 = 0.32, F = 0.48, p = 0.61), PPT (η2 = 0.73, F = 2.80, p = 0.06), ODI (η 2 = 0.02, F = 0.02, p = 0.97). (4) Conclusion: A single trial of thoracolumbar myofascial release technique was not enough to reduce pain and disability in subjects with CLBP.

Low Back Pain (LBP) is one of the most common problems among adults. The usual physiotherapy treatment is to perform physical exercises. However, some LBP patients have false beliefs regarding their pain and they tend to avoid physical movements which might increase their pain and disability. Virtual Reality (VR) has shown to be an effective intervention in improving motor functions and reducing pain perception. Existing VR interventions for LBP rehabilitation were based on a non-immersive VR, whereas to effectively reduce the pain intensity, we need an immersive VR. In this paper, we introduce the development and evaluation of a serious game called RabbitRun with an immersive experience to engage the patients in a virtual environment and distract them from the pain while performing LBP exercises. The initial usability evaluation results suggest that RabbitRun game is enjoyable and acceptable. The game is easy to play and learn and most of the participants are willing to play the game at home. This solution will enhance the rehabilitation outcome since the patients who are suffering from LBP can use the system at their home and train more for long period of time using a smartphone and low-cost virtual reality device such as Google Cardboard.

Research on Traffic Light Recognition (TLR) has grown in recent years, primarily driven by the growing interest in autonomous vehicles development. Machine Learning algorithms have been widely used to that purpose. Mainstream approaches, however, require large amount of data to properly work, and as a consequence, a lot of computational resources. In this paper we propose the use of Expert Instruction (IE) as a mechanism to reduce the amount of data required to provide accurate ML models for TLR. Given an image of the exterior scene taken from the inside of the vehicle, we stand the hypothesis that the picture of a traffic light is more likely to appear in the central and upper regions of the image. Frequency Maps of traffic light location were thus constructed to confirm this hypothesis. The frequency maps are the result of a manual effort of human experts in annotating each image with the coordinates of the region where the traffic light appears. Results show that EI increased the accuracy obtained by the classification algorithm in two different image datasets by at least 15%. Evaluation rates achieved by the inclusion of EI were also higher in further experiments, including traffic light detection followed by classification by the trained algorithm. The inclusion of EI in the PCANet achieved a precision of 83% and recall of 73% against 75.3% and 51.1%, respectively, of its counterpart. We finally presents a prototype of a TLR Device with that expert model embedded to assist drivers. The TLR uses a smartphone as a camera and processing unit. To show the feasibility of the apparatus, a dataset was obtained in real time usage and tested in an Adaptive Background Suppression Filter (AdaBSF) and Support Vector Machines (SVMs) algorithm to detect and recognize traffic lights. Results show precision of 100% and recall of 65%.

There is an increasing need for quantitative rockfall hazard and risk assessment that requires a precise definition of the terms and concepts used for this particular type of landslide. This paper suggests to use terms that appear to be the more logic and explicit as possible, and describes methods to derive some of the main hazard and risk descriptors. The terms and concepts presented concern the rockfall process (failure, propagation, fragmentation, modelling) and the hazard and risk descriptors, distinguishing the cases of localized hazards and diffused hazards. For a localized hazard, the failure probability of the considered rock compartment in a given period of time has to be assessed and the probability for a given element at risk to be impacted with a given energy must be derived combining the failure probability, the propagation probability and the exposure of the element. For a diffuse hazard that is characterized by a failure frequency, the number of rockfalls reaching the element at risk per unit of time and with a given energy (reach frequency) can be derived. However, when the element at risk is not replaced or repaired, the probability that it is impacted by at least one rockfall must be considered.

Separation and detection of cells and particles in a suspension are essential for various applications, including biomedical investigations and clinical diagnostics. Microfluidics realizes the miniaturization of analytical devices by controlling the motion of a small volume of fluids in microchannels and microchambers. Accordingly, microfluidic devices have been widely used in particle/ cell manipulation processes. Different microfluidic methods for particle separation include dielectrophoretic, magnetic, optical, acoustic, hydrodynamic, and chemical techniques. Dielectrophoresis (DEP) is a method for manipulating polarizable particles’ trajectories in non-uniform electric fields using unique dielectric characteristics. It provides several advantages for dealing with neutral bioparticles owing to its sensitivity, selectivity, and noninvasive nature. This review provides a detailed study on the signal-based DEP methods that use the applied signal parameters, including frequency, amplitude, phase, and shape for cell/particle separation and manipulation. Rather than employing complex channels or time-consuming fabrication procedures, these methods realize sorting and detecting the cells/particles by modifying the signal parameters while using a simple device. In addition, these methods can significantly impact clinical diagnostics by making low-cost and rapid separation possible.

Low-temperature processed ITO thin films offer the potential of overcoming the doping limit by suppressing the equilibrium of compensating oxygen interstitial defects. To elucidate this potential, electrical properties of Sn-doped In₂O₃ (ITO) thin films are studied in dependence on film thickness. In-operando conductivity and Hall effect measurements during annealing of room temperature deposited films with different film thickness in different environments allow to discriminate between the effects of crystallization, grain growth, donor activation and oxygen diffusion on carrier concentrations and mobilities. At 200 °C, a control of carrier concentration by oxygen incorporation or extraction is only possible for very thin films. The electrical properties of thicker films deposited at room temperature are mostly affected by grain size. The remaining diffusivity of compensating oxygen defects at 200 °C is sufficient to screen the high Fermi level induced by deposition of Al₂O₃ using atomic layer deposition (ALD), which disables the use of defect modulation doping at this temperature. The results indicate that achieving higher carrier concentrations requires a control of the oxygen pressure during deposition in combination with seed layers to enhance crystallinity or the use of near room temperature ALD.

During recent years UAVs have been increasingly used in agriculture and forestry research and application. Nevertheless, most of this work has been devoted to improving accuracy and explanatory power, often at the cost of usability and affordability. We tested a low-cost UAV and a simple workflow to apply four different greenness indices to the monitoring of pine (Pinus sylvestris and P. nigra) after-fire regeneration in a Mediterranean forest. We selected two sites and masured all pines within a pre-selected plot. Winter flights were carried out at each of the sites, at two flight altitudes (50 and 100 m). Automatically normalizing images entered an SfM based photogrammetric software for restitution and the obtained point cloud and orthomosaic processed to get a canopy height model and four different greenness indices. Sum of pine DBH was regressed on summary statistics of greenness indices and canopy height model. ExGI and GCC indices outperformed VARI and GRVI in estimating pine DBH, while canopy height model slightly improved the models. Flight altitude did not severely affect model performance. Our results show that low cost UAVs may improve forest monitoring after disturbance, even in those habitats and situations were resource limitation is an issue.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Cuticular waxes are a mixture of hydrophobic very-long-chain fatty acids and their derivatives accumulated in the plant cuticle. Most studies define the role of cuticular wax largely based on reducing non-stomatal water loss. The present study investigated the role of cuticular wax in reducing both low-temperature and dehydration stress in plants using Arabidopsis thaliana mutants and transgenic genotypes altered in the formation of cuticular wax. cer3-6, a known Arabidopsis wax-deficient mutant (with distinct reduction in aldehydes, n-alkanes, secondary n-alcohols, and ketones compared to wild type (WT)), was most sensitive to water loss; while dewax, a known wax overproducer (greater alkanes and ketones compared to WT), was more resistant to dehydration compared to WT. Furthermore, cold-acclimated cer3-6 froze at warmer temperatures, while cold-acclimated dewax displayed freezing exotherms at colder temperatures compared to WT. GC-MS analysis identified a characteristic decrease in the accumulation of certain waxes (e.g. alkanes, alcohols) in Arabidopsis cuticles under cold acclimation, which was additionally reduced in cer3-6. Conversely, the dewax mutant showed a greater ability to accumulate waxes under cold acclimation. FTIR spectroscopy also supported observations in cuticular wax deposition under cold acclimation. Our data indicate cuticular alkane waxes along with alcohols and fatty acids can facilitate avoidance of both ice formation and leaf water loss under dehydration stress, and are promising genetic targets of interest.

Existing methods enhance mid-low resolution remote sensing ship detection by feeding super-resolved images to the detectors. Although these methods marginally improve the detection accuracy, the correlation between image super-resolution (SR) and ship detection is under-exploited. In this paper, we propose a simple but effective ship detection method called ShipSR-Det, in which both the output image and the intermediate features of the SR module are fed to the detection module. Using the super-resolved feature representation, the potential benefit introduced by image SR can be fully used for ship detection. We apply our method to the SSD and Faster-RCNN detectors and develop ShipSR-SSD and ShipSR-Faster-RCNN, respectively. Extensive ablation studies validate the effectiveness and generality of our method. Moreover, we compare ShipSR-Faster-RCNN with several state-of-the-art ship detection methods. Comparative results on the HRSC2016, DOTA and NWPU VHR-10 datasets demonstrate the superior performance of our proposed method.

The production and secretion of very-low density lipoproteins (VLDL) by hepatocytes has a direct impact on liver fat content as well as the concentration of cholesterol and triglycerides in the circulation and thus affects liver and cardiovascular health, respectively. Importantly, excess caloric intake and lack of physical activity are associated with overproduction of VLDL, hepatic steatosis, and increased levels of atherogenic lipoproteins. Cholesterol as well as triglycerides in remnant particles after VLDL lipolysis are risk factors for atherosclerotic cardiovascular disease (ASCVD) and have garnered increasing attention over the last few decades. To date, however, increased risk of ASCVD is not the only concern when considering today’s cardiometabolic patients, as they often also suffer from hepatic steatosis. This notion highlights the importance of understanding the molecular regulation of VLDL biogenesis. Fortunately, there has been a resurgence of interest in the intracellular assembly, trafficking, degradation, and secretion of VLDL by hepatocytes, that has led to many exciting new molecular insights, the topic of this review. We think that increasing our understanding of the biology of this pathway will help improve the health of the cardiometabolic patient in the long term.

An antenna sensor is proposed to execute dual functions of antenna and sensor in the wireless sensor system, in order to reduce data loss and to increase transmission rate by omitting a certain interface. The as-made sensor was test at a center frequency of 46 MHz for measuring human finger postures using principle of dipole antenna. The antenna sensor was attached on a wearable glove. The results showed that the motion sensor can accurately identify finger angles at 0°, 20°, 40°, 60° and 80°.