Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

Tungsten carbide (WC) was well known as a wear-resistant material. Iron-based pow-der was suitable for remanufacturing of cast iron engine parts. To improve the wear resistance of the remanufactured iron-based cast iron engine parts, WC-Co was intro-duced into iron-based powders to prepare composite coatings for cast iron engine components. In this work, FeAlC-x(WC-Co) composite coatings were prepared by plasma transfer arc on compacted graphite cast iron. The influences of WC-Co con-tents in the Fe-AlC-x(WC-Co) composite coatings on the microstructure and properties of the composite coatings were investigated. The composite coatings contained γ-Fe, α-Fe, WC and Fe3W3C mainly. The microhardness of FeAlC-x(WC-Co) composite coatings had the highest hardness of 814 HV0.2, the-lowest coefficient of 0.5 and the lest wear mass loss of 1.3mg when the weight content of WC-Co in the composite coating was 20wt%. As compared with the FeAlC coating, FeAlC-x(WC-Co) composite coating achieved the effect of reducing friction and wear resistance simultaneously, which resulted from the self-lubricating effect of graphite and high wear-resistance of carbides in the claddings.

Stable half-sandwich iron(II) dihalido complexes of the type [Fe(5-Cp’)X2] are extremely scarce, being limited to congeners containing the bulky C5H2-1,2,4-tBu3 ligand. We have extended this to homologues [Fe(5-Cp*)X2] (X = Cl – I) containing the particularly popular C5Me5 (Cp*) ligand. Corresponding ionic compounds ER4[Fe(5-Cp*)X2] are easily accessible from FeX2, MCp* (M = Li, K) and a suitable halide source R4EX (E = N, P) in THF. The new compounds NnPr4[Fe(5-Cp*)X2] (X = Cl, Br), NnPr4[Fe(5-Cp*)BrCl] and PPh4[Fe(5-Cp*)X2] (X = Cl, Br, I) have been structurally characterised by single-crystal X-ray diffraction. NnPr4[Fe(5-Cp*)Cl2] reacts readily with CO to afford [Fe(5-Cp*)Cl(CO)2], indicating the synthetic potential of ER4[Fe(5-Cp*)X2] in FeCp* half-sandwich chemistry.

Brassicaceae are well known as non-arbuscular mycorrhizal (AM) host plants. This study was aimed to examine effects of two Brassica; cabbage (Brassica oleracea L. cv. cabitata) and mustard (B. juncea Coss.) on three AM species (Acaulospora, Entrophospora and Glomus) and to examine effect of root incorporation into soil on root AM infectivity in maize growing in iron toxicity soil. Experiment 1, cabbage and mustard crop reduced spore density of Acaulospora, but there was no effect on spore density of Entrophospora. While, mustard crop had more effect on Glomus spore density than cabbage crop. Experiment 2, AM spore from two conditions; without and with 6 weeks of root residues (cabbage, mustard and maize) incorporation was examined for its infectivity in maize roots. At D21, without root incorporated, the infectivity of Acaulospora, Entrophospora and Glomus were not different. By contrast, cabbage and mustard root incorporation depressed infec-tivity of Acaulospora but, there was no effect on Entrophospora. Whereas, cabbage root incorporation only depressed infectivity of Glomus. However, AM infectivity was recovered at D42. These results suggested that Brassica root incorporated into soil was the actual effect on the viability of AM spore resulting in reduction of AM infectivity at the early stage.

Transferrin (TF) is a key iron carrier protein. Studies in human cohorts and in cultured adipocytes suggested that decreased transferrin expression and intracellular iron in adipocytes leads to impaired insulin responsiveness and causes differential expression of genes involved in metabolism, insulin action, and obesity. While suggestive, these studies did not definitively prove in an intact organism that altering TF expression in adipocytes is sufficient to affect glucose homeostasis and insulin resistance. In this study we created a mouse model of decreased transferrin expression only in adipocytes (Trf+/-Cre+/-) to test the hypothesis that iron trafficking in adipose tissue is sufficient to affect insulin sensitivity. Area under the glucose curve (AUCg) after intraperitoneal glucose administration was increased in the Trf+/-Cre+/- mice compared to wild type (WT) mice on a normal chow diet, and the mice were slightly heavier (p=0.02 for both). Homeostasis Model of Insulin Resistance (HOMA-IR) values were also significantly higher in the Trf+/- Cre+/- mice (p<0.05). Thus, supporting our hypothesis, analysis of mice with decreased expression of TF restricted to adipocytes showed that a decrease in adipocyte TF is sufficient to affect insulin resistance, weight, and glucose homeostasis.

Arsenic (As) is the most poisonous metalloid with negative effects on the plant and ecosystem. In the current study, observed that iron oxide nanoparticles (NPs) affected the molecular features of rice under arsenic (As) stress. The result showed that 1-D electrophoresis (SDS-PAGE) demonstrated variable expression of protein profiles. The polypeptide pattern was altered in the SDS-PAGE under arsenic stress. The findings also showed that low molecular weight polypeptides (MTs) expression was maximum under arsenic stress, while iron oxide NPs decreased the expression of these polypeptides and reduced the arsenic stress. RT-PCR was used to analyse the expression of the MYB transcriptional factor, WRKY, and OsGF14 genes in the rice plant. The results showed that these genes were up-regulated in response to arsenic stress, iron oxide NPs reduced arsenic stress, and Myeloblastosis (MYB), WRKY, and OsGF14 genes had very low expression levels. Our work showed that iron oxide nanoparticles (NPs) not only reduced the effects of arsenic stress but also decreased the expression of stress-related genes and metallothioneins (MTs).

Iron oxide nanoparticles have been investigated due to their suitable characteristics for diverse applications in the fields of biomedicine, electronics, water/wastewater treatment and sensors. Maghemite, magnetite and hematite are the most widely studied iron oxide particles and have ferrimagnetic characteristics. When very small, however, these particles have superparamagnetic properties and are called superparamagnetic iron oxide nanoparticles (SPIONs). Several methods are used for the production of these particles, such as coprecipitation, thermal decomposition and microemulsion. However, the variables of the different types of synthesis must be assessed to achieve greater control over the particles produced. In some studies, it is possible to compare the influence of variations in the factors for production with each of these methods. Thus, researchers use different adaptations of synthesis based on each objective and type of application. With coprecipitation, it is possible to obtain smaller, more uniform particles with adjustments in temperature, pH and the types of reagents used in the process. With thermal decomposition, greater control is needed over time, temperature as well as the proportion of surfactants and organic and aqueous phases in order to produce smaller particles and a narrower size distribution. With the microemulsion process, the control of the confinement of the micelles formed during synthesis through the proportions of surfactant and oil makes the final particles smaller and less dispersed. These nanoparticles can be used as additives for the creation of new materials, such as magnetic bacterial cellulose, which has different innovative applications. Composites that have SPIONs, which are produced with greater rigour with regards to size and distribution, have superparamagnetic properties and can be used in medical applications, whereas materials containing larger particles have ferromagnetic applications. To arrive at a particular particle with specific characteristics, researchers must be attentive to both the mechanism selected and the production variables to ensure greater quality and control of the materials produced.

Nowadays, there is evidence that bacteria can contribute to cancer formation and interfere with therapy by mediating its carcinogenesis and related infection. Moreover, it is acknowledged that microbial infections and antibiotic resistance represent severe economic and health risks to society. These facts have led to the developing of several new techniques for impeding crucial biological processes in microbial cells. One of these techniques centers on using metal-chelating agents, which can disrupt the microorganism's vital metal metabolism by obstructing metal uptake and bioavailability for critical reactions. Additionally, nanotechnology has made a wide range of nanomaterials available for possible uses in the antibacterial industry. This complex field is shaped by antimicrobial nanoparticles, also investigated as therapeutic and drug-delivery tools. Halloysite nanotubes (HNTs) are naturally occurring tubular clay nanomaterials consisting of aluminosilicate kaolin sheets rolled up several times. The aluminon and siloxane groups on the surface of HNTs facilitate the formation of hydrogen bonds with biomaterials on their surface. These properties make HNTs crucial in a wide range of applications, such as in environmental sciences, wastewater treatment, dye removal, nanoelectronics and nanocomposite fabrication, catalytic studies, coatings for glass or anti-corrosive coatings, cosmetics, flame retardants, stimulus-response, and in forensic sciences. This work aimed to produce an antibacterial material by combining the properties of halloysite nanotubes with the ability of kojic acid to chelate iron. Starting from kojic acid, a simple nucleophilic substitution involving the hydroxyl groups on the surface of the nanotubes was performed. The obtained material was characterized by IR and SEM, and its ability to chelate iron was evaluated. Finally, the capacity to load drugs such as resveratrol and curcumin was also evaluated by UV analysis. In this way, a new bio-based material that can be used as a drug carrier and antimicrobial was produced.

This study presents a tri-layer broadband metamaterial absorber which operates in the GHz range. The absorber was composed of a polyhedral iron-cobalt alloy/graphite nanosheet material arranged in a flat sheet with two punched-in rings for the top layer, a continuous FR-4 layer at the middle, and a continuous copper layer at the bottom. For the normal incidence of electromagnetic wave, the proposed absorber demonstrated an exceptional broadband absorption in a frequency range of 7.9-14.6 GHz, revealing an absorption exceeding 90%. The absorption magnitude remains to be above 90% in a frequency range of 8-11.1 GHz for transverse-electric-polarized waves at incident angles up to 55°. For both transverse-magnetic- and electric-polarized waves, the absorption exceeds 90% in a frequency range of 9.5-14.6 GHz. The physical mechanism behind the absorption properties is analyzed thoroughly through the electric- and magnetic-field distributions. The obtained results could contribute potentially to the development of microwave applications based on metamaterial absorbers, such as radar-stealth technology, electromagnetic shielding for health safety and reduced electromagnetic interferences for high-performance communications and electronic devices.

In eutrophic waters, such as Mikawa Bay, Japan, anoxic bottom water develops in summer. This causes sulfide release into seawater by sulfate reduction in the sediment, leading to environmental problems. The addition of iron to sediments is a method used to improve the sediment environment, which was devised from a natural phenomenon. However, this method has not yet been quantitatively evaluated. In this study, we aim to quantitatively evaluate the suppressive effect of iron on sulfide release. First, we develop a sediment model that focuses on S and Fe. We then attempted to reproduce the observations and experiments on sulfide dynamics using the model. Consequently, the proposed model was able to reproduce field sulfur and Fe dynamics in sediments. Additionally, the model described the characteristics of sulfide release considering the effects of additive iron materials. Finally, we conducted predictive calculations and quantitatively evaluated the effects of adding iron materials to the sediments in terms of sulfur and iron cycles.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

Children under two years old are at risk for anemia because young children have an increased need for iron for their physical growth and brain development. The purpose of this study was designed to evaluate the effects of a caregiver potential support program on anemia prevention in children six months to two years old attending the subdistrict health-promoting hospital in Thasala District, Nakhon Si Thammarat Province. This study was quasi-experimental. The sample included children aged six months to two years old and their caregivers, who were selected by random sampling and allocated to either the experimental or control group, with 40 pairs per group. The experimental group received a potential support program, while the control group received regular care. Both groups were followed for 12 weeks. The instruments used were the potential caregiver assessment, children’s anemia assessment, and a program to support the potential of primary caregivers. Descriptive statistics, chi-square, and t-tests were used to analyze the data. The results revealed that 11.4% of the children had anemia, and a hematocrit count of less than 33% (range = 30-40, M = 34.89, SD = 1.97). The mean scores of knowledge about anemia and iron supplementation after using the program in the experimental group and control group were significantly different (p < 0.001). The mean scores of knowledge about anemia in the experimental and control group were 15.75, SD = 0.54, and 13.28, SD = 1.43 respectively. The mean scores of knowledge about iron supplementation in the experimental and control group were 10.75, SD = 0.49, and 8.15, SD = 1.54 respectively. It was found that the experimental group had a higher mean score on food care behaviors than the control group for 6-11 months and 1-2 years, with statistical significance. The experimental group also had a higher mean score of care behaviors concerning children’s consumption of medicine than the control group (M = 58.20, SD = 4.05; M = 45.78, SD = 9.66, respectively), (p < 0.001). The mean score of the hematocrit level for the experimental group was found to be higher than the control group after receiving the program (M = 35.80, SD = 1.55; M = 34.83, SD = 2.14, respectively), (p < 0.05). Therefore, healthcare providers should support caregivers' capacity to provide continued care for children to prevent anemia.

The development and improvement of methods for the synthesis of environmentally friendly catalysts based on base metals is currently an urgent and promising task of modern catalysis. Catalysts based on nanoscale magnetite and maghemite have fast adsorption-desorption kinetics and high chemical activity. The purpose of this work was to obtain magnetic composites, determine their physicochemical characteristics and verify their activity in the process of liquid-phase oxidation of phenol with oxygen. Magnetic nanocomposites were obtained by chemical co-deposition of salts of ferrous and trivalent iron. The synthesized magnetic composites were studied by X-ray diffractometry, energy dispersive X-ray fluorescence and Mössbauer spectroscopy, IR-Fourier spectroscopy, elemental analysis. To increase the catalytic activity in oxidative processes, the magnetite surfaces were modified using cobalt nitrate salt. Further, CoFe2O4 was stabilized by adding polyethylenimine (PEI) as a surfactant. Preliminary studies of the oxidation of phenol with oxygen, as the most typical environmental pollutant were carried out on the obtained Fe3O4, CuFe2O4, CoFe2O4/PEI catalysts. The spectrum of the reaction product shows the presence of CH in the aromatic ring and double C=C bonds, stretching vibrations of the C=O groups of carbonyl compounds; the band at 3059 cm–1 corresponds to the presence of double C=C bonds, the band at 3424 cm–1 hydroquinone compounds. The band at 1678 cm–1 and the intense band at 1646 cm–1 refer to vibrations of the С=О bonds of the carbonyl group of benzoquinone. Peaks at 1366 cm–1 and 1310 cm–1 can be related to the vibrations of C–H and C–C bonds of the quinone ring. Thus it was demonstrated that produced magnetic composites based on iron oxide are quite effective in the oxidation of phenol with oxygen.

The transport of iron(III) from Fe(III)-Mn(II)-HCl mixed solutions through a flat-sheet supported liquid membrane is investigated, being the carrier phase of Cyanex 923 (commercially available phosphine oxide extractant) dissolved in Solvesso 100 (commercially available diluent), as a function of hydrodynamic conditions, concentration of manganese and HCl in the feed phase, and carrier concentration in the membrane phase. A transport model is derived that describes the transport mechanism, consisting of diffusion through a feed aqueous diffusion layer, a fast interfacial chemical reaction, and diffusion of the Fe(III)-Cyanex 923 complex across the membrane phase. The membrane diffusional resistance (Δm) and feed diffusional resistance (Δf) are calculated from the model, and their values are 145 s/cm and 361 s/cm, respectively. It is apparent that the transport of iron(III) is mainly controlled by diffusion through the aqueous feed boundary layer, being the thickness of this layer calculated as 2.9x10-3 cm. Since Mn(II) is not transported through the membrane phase, the present system allows to the purification of this manganese-bearing solutions.

All over the world birds’ eggs are an important and valuable component of the human diet. The study aimed to compare the content of lipid components and their nutritional value as well as iron and zinc levels in chicken and quail eggs commonly available on the market. In egg lipids, unsaturated acids were dominated, especially oleic acid, the content of which was about 40% of total fatty acids (TFA). Linoleic acid was the major polyunsaturated fatty acid. Compared to other products of animal origin, eggs were characterized by favourable values of lipid quality indices, especially index of atherogenicity, thrombogenicity and hypocholesterolemic to hypercholesterolemic ratio. In the present study, no differences in the content of tested nutrients between eggs from different production methods (organic, free-range, barn, cages), as well as inter-breed differences were noticed. Cluster analysis showed that eggs enriched in n3 PUFA (according to producers’ declaration) differ from other groups of chicken eggs. However, only in eggs from one producer, the amount of EPA and DHA exceed 80 mg per 100 g, entitling to use the nutrition claim on the package. Quail eggs differed from chicken eggs in FA profile; they also had much higher iron and cholesterol levels.

This research evaluates the inhibitory effect of L-amino acids (AAs) with different side chain lengths on Fe surface implementing Monte Carlo (MC) simulation. A quantitative and qualitative description of the adsorption behavior of AAs on the iron surface has been carried out. Calculations have shown that the absolute values of the adsorption energy of L-amino acids increase with side chain prolongation; they are also determined by the presence of heteroatoms. AAs from nonpolar and basic groups have the best adsorption ability to the iron surface, which indicates their highest inhibitory efficiency according to the results of MC simulation.

Thalassemia is genetic blood disease cause by absence or decrease of one or more of the globin chain synthesis. Beta thalassemia is characterized by one or more mutations in beta globin gene. Absence or reduced amount the of beta globin chains cause ineffective erythropoiesis which leads to anemia. Beta thalassemia has been further divided into three main forms: Thalassemia minor/silent carrier, major and intermedia. More severe form is thalassemia major in which patients depend upon blood transfusion for survival and high level of iron occur as a consequence of consistent blood transfusion. Over loaded iron invokes the synthesis of reactive oxygen species that are toxic in redundancy and triggering the impairment to vascular, endocrine and hepatic system. Thalassemia can be diagnosed and detected through various laboratory tests such as blood smear, prenatal testing (genetic testing of amniotic fluid), DNA analysis (genetic testing) and complete blood count. Treatment of thalassemia intermedia is symptomatic but it can also be managed by splenectomy and folic supplementation. While thalassemia major can be treated by transplantation of bone marrow, regular transfusion of blood and iron chelation treatment, stimulation of fetal hemoglobin production, hematopoietic stem cell transplantation and gene therapy.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Iron oxide nanoparticles are widely used as contrast agent for MRI and may be used as therapeutic agent by magnetic hyperthermia if they display a high magnetic anisotropy. Considering the effect of the nanoparticles shape on anisotropy, the reproducible shape control of nanoparticles is currently a challenge of synthesis methods. By investigating reaction parameters which are the iron precursor structure, the water content and the amount of the surfactant, sodium oleate, reported to trigger the cubic shape, iron oxide nanoparticles with different shape and composition were observed to form. In particular, iron oxide nanoplates have been thus synthesized. The effect of the surfactant coming from precursor was taking into account by using in house iron stearates bearing either two or three stearate chains and the negative effect of water on shape was confirmed by considering these precursors after their dehydration. Nanocubes with straight faces and a FeO@Fe3-xO4 composition were obtained only with dehydrated precursors and 50% of sodium oleate in the oleic acid and sodium oleate surfactant mixtures. When iron stearates with three chains led mainly to nanocubes in presence of soduim oleate, Iron stearates with two chains led to the formation of nanoplates with 80% of sodium oleate. The original flat shape of the plates was confirmed with 3D TEM tomography. The investigation of the synthesis mechanisms confirmed the major role of deprotonated carboxylic acid and of the heating rate to drive the cubic shape of nanoparticles and showed that the nanoplate formation would depend mainly on the nucleation step and possibly on the presence of a given ratio of oleic acid and deprotonated carboxylic acid.

Two types of heterometallic (Fe(III),Na) silsesquioxanes [Ph₅Si₅O₁₀]₂[Ph₁₀Si₁₀O₂₁]Fe₆(O^2‒)₂Na₇(H₃O⁺)(MeOH)₂(MeCN)_4.5.1.25(MeCN), I, and [Ph₅Si₅O₁₀]₂[Ph₄Si₄O₈]₂Fe₆Na₆(O^2‒)₃(MeCN)_8.5(H₂O)_8.44, II, were obtained and characterized. X-Ray studies established distinctive structures of both products, with pair of Fe(III)-O-based triangles surrounded by siloxanolate ligands, giving fascinating cage architectures. Complex II proved to be catalytically active in the formation of amides from alcohols and amines, thus becoming a rare example of metallasilsesquioxanes performing homogeneous catalysis. Benzene, cyclohexane and other alkanes, as well as alcohols, can be oxidized in acetonitrile solution to phenol, the corresponding alkyl hydroperoxides and ketones, respectively, by hydrogen peroxide in air in the presence of catalytic amounts of complex II and trifluoroacetic acid. Thus, the cyclohexane oxidation at 20 °C gave oxygenates in very high for alkanes yield (48% based on alkane). The kinetic behaviour of the system indicates that the mechanism includes the formation of hydroxyl radicals generated from hydrogen peroxide in its interaction with diiron species. The latter are formed via monomerization of starting hexairon complex with further dimerization of the monomers.

Aero submarines (aerosubs) are vehicles that can both fly both in air and travel under water. The concept of dual aerial and aquatic vehicles emerged in 1939 when Russian engineer Boris Ushakov proposed the “flying submarine”[1], and this was followed by further developments including RFS1 [2], convair project in 1964[3] , etc. however, to date, limited attempt has been diverted towards the advanced development of such aircraft. This is heavily influenced by challenges associated with the design and operation of the same. Based on the review of literature the authors aim to introduce a theoretical design for an aerosub (QFS-20) with a view to address the design and operation issues including power, entry to and exit from water.

The expression "Follow the water" is used in order to recognize inside the universe, life as it exists on Earth. It is shown here that the expression "Follow the water in its high-subcritical state" can be used in order to recognize the components of life which form prior to the emergence of life. This specific state of water leaves signatures inside the minerals which are produced during high-subcritical water/rock interaction.

Fungi are ubiquitous and metabolically versatile. Their dispersion has important scientific, environmental, health, and economic implications. They can be dispersed through the air by the aerosolization of near surfaces or transported from distant sources. Here, we tested the contribution of local (scale of meters) versus regional (kilometers) sources by analyzing airborne fungal community by ITS sequencing around a copper mine in the North of Chile. The mine was the regional source, whereas soil and vegetal detritus were the local sources at each point. The airborne community was highly homogeneous in ca. 2,000 km2, impeding the detection of regional or local contributions. Ascomycota was the dominant phylum in the three communities. Soil and vegetal detritus communities had lower alpha-diversity, but some taxa had abundance patterns related to the distance to the mine and altitude. On the contrary, the air was compositionally even and unrelated to environmental or spatial factors, except for altitude. The presence of plant pathogens in the air suggests that other distant sources contribute to this region's airborne fungal community and reinforces the complexity of tracking the sources of air microbial communities in a real world where several natural and human activities coexist.

Fractal analysis of time series aims to extract the hidden or complex structures issued from the associated real data, such as scaling laws, non-stationary, dynamics, and so on. In the present work, the air quality index and its components are considered as time series owing fractal structures. To understand their underlying dynamics, wavelet multifractal approach is applied starting with a wavelet multifractal spectrum test to confirm the multifractality of the underlying data. Next, a new model is introduced improving the classical minmax one, provided with a statistical measure for the adequacy of the new model. The theoretical findings are applied to the north west Tabuk region of Saudi Arabia for environmental and climate data related to pollutants and factors involved in the estimation of the air quality index.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: describe briefly the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article, it must not contain results which are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The unquenchable demand for rock materials has attracted many companies within the building and construction sector to invest in stone quarrying. However, this has brought about the environmental impacts with health threats to people. There is a paucity of information about the magnitude of pollution on air and water and how it varies with quarry sites. This study therefore investigated the physical impacts of quarrying on air and water and explored the in-situ mitigations to undesirable effects due to stone quarrying. Four active quarry sites were identified. Field measurements of dust (particulate matter) was conducted within the four quarry sites and in the nearby community. Water samples were collected from quarry pits and nearby shallow wells for laboratory analysis of water quality. Statistical Analysis of Variance (ANOVA) was used to test for differences in pollution across the four studied sites. Results revealed that, amidst use of wet crushing and water sprinkling on bare surfaces, dust emission was higher than the recommended permissible standards levels with a significant variation across the quarry sites with ANOVA (P-value=0.003) for PM2.5 and (P-value=0.04366) for PM10. Water pollution was mainly contributed by the non-permissive levels of nitrates, chromium, and pH. Polluted air and water are associated with sparking off health threats to the users in the community. In conclusion, quarry companies should strengthen the already existing mitigation of dust suppression. The study recommends additional measures such as treating quarry pit water before discharging to the open environment

Social distancing policies put in place during COVID-19 epidemic in addition to helping to limit the spread of the disease also contributed to improving urban air quality. Here we show a decrease in air pollutant concentration as a consequence of mobility reduction in São Paulo during the containment measure which began on 22^nd March 2020. When comparing to foregoing weeks to equivalent periods of 2019, the concentration of most air pollutants sharply decreased in the first days of mobility restriction, to then increase again after government officials downplayed the threat of the disease. This trend is also followed by a decrease in hospital admissions by SARS-influenza. Therefore, despite the great economic and social unrest caused by the pandemic, this unique situation shows that large-scale mobility reduction policy had a significant impact on air quality, benefiting, directly and indirectly, the public health system.

Several methods have been tried to estimate air temperature using satellite imagery. In this paper, the results of two machine learning algorithms, Support Vector Machine and Random Forest, are compared with Multivariate Linear Regression, TVX and Ordinary kriging. Several geographic, remote sensing and time variables are used as predictors. The validation is carried out using four different statistics on a daily basis allowing the use of ANOVA to compare the results. The main conclusion is that Random Forest with residual kriging produces the best results (R$^2$=0.612 $\pm$ 0.019, NSE=0.578 $\pm$ 0.025, RMSE=1.068 $\pm$ 0.027, PBIAS=-0.172 $\pm$ 0.046), whereas TVX produces the least accurate results. The environmental conditions in the study area are not really suited to TVX, moreover this method only takes into account satellite data. On the other hand, regression methods (Support Vector Machine, Random Forest and Multivariate Linear Regression) use several parameters that are easily calculated from a Digital Elevation Model, adding very little difficulty to the use of satellite data alone. The most important variables in the Random Forest Model were satellite temperature, potential irradiation and cdayt, a cosine transformation of the julian day.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

The air quality monitoring network in Alaska is currently limited to ground-based observations in urban areas and national parks leaving a large proportion of the state unmonitored. The use of MODIS aerosol optical depth (AOD) to estimate ground-level particulate pollution concentrations has been successfully demonstrated around the world, and could potentially be used in Alaska. In this work, MODIS AOD measurements at 550 nm were validated against AOD derived from AERONET ground-based sunphotometers in Barrow and Bonanza Creek to determine if MODIS AOD from the Terra and Aqua satellites could be used to estimate ground-level particulate pollution concentrations. The MODIS AOD was obtained from MODIS collection 6 using the dark target Land and Ocean algorithms from 2000 to 2014. MODIS data could only be obtained between the months of April and October; therefore, it could only be validated for those months. Individual and combined Terra and Aqua MODIS data were considered. The results showed that MODIS collection 6 products at 10 km resolution for Terra and Aqua combined are not valid over land but are valid over the ocean. On the other hand, the individual Terra and Aqua MODIS collection 6 AOD products at 10 km resolution are valid over land individually but not when combined. Results also suggest the MODIS collection 6 AOD products at 3 km resolution are valid over land and ocean and perform better over land than the 10-km product. These findings indicate that MODIS collection 6 AOD products can be used quantitatively in air quality applications in Alaska during the summer months.

Local air quality is a major concern for the population regularly exposed to high levels of air pollution. The airport, mainly due to its aircraft engines activities during taxiing and take off, is often submitted to heterogeneous but important concentrations of NOx and PM. The study suggests an innovative approach to determine the air traffic impact on air quality at the scale of the airport, its runways and terminals, in order to be able to locate the persistent high concentrations spots. The pollutants concentrations at 10 m resolution and 1 s time step are calculated in order to identify the most affected areas of an airport platform. A real day of air traffic on a regional airport is simulated, using real data as aircraft trajectories (from radar streams). In order to estimate the aircraft emissions, the Air Transport Systems Evaluation Infrastructure (IESTA) is used. Regarding local air quality, IESTA relies on the non-hydrostatic meso-scale atmospheric model Meso-NH using grid-nesting capabilities with 3 domains, for this study. The detailed cartography of the airport distinguishes between grassland, parking and terminals, allowing to compute exchanges of heat, water and momentum between the different types of surfaces and the atmosphere as well as the interactions with the building using a drag force. The dynamic parameters like wind, temperature, turbulent kinetic energy and pollutants concentration are computed at 10 m resolution over the 2 × 4 km airport domain. The pollutants are considered in this preliminary study as passive tracers, without chemical reactions. This preliminary study aims at proving the feasibility of high scale modelling over an airport with state of the art physical models.

Viruses rely on host cells to replicate their genomes and assemble new viral particles. Thus, they have evolved intricate mechanisms to exploit host factors. Host cells, in turn, have developed strategies to inhibit viruses, resulting in a nuanced interplay of co-evolution between virus and host. This dynamic often involves competition for resources crucial for both host cell survival and virus replication. Iron and iron-containing cofactors, including iron-sulfur clusters, are known to be a heavily battled resource during bacterial infections where control over iron can tug the war in favor of the pathogen or the host. It is logical to assume that viruses also engage in this competition. Surprisingly, our knowledge about how viruses utilize iron (Fe) and iron-sulfur (FeS) clusters remains limited. The handful of reviews on this topic primarily emphasize the significance of iron in supporting the host immune response against viral infections. The aim of this review, however, is to organize our current understanding of how viral proteins utilize FeS clusters, to give perspectives on what questions to ask next and to propose important avenues for future investigations.

When it comes to air pollution complaints, odours are often the most significant contributor. Sources of odour emissions range from natural to anthropogenic. Mitigation of odour can be challenging, multifaceted, site-specific, and is often confounded by its complexity—defined by existing (or non-existing) environmental laws, public ordinances, and socio-economic considerations. The objective of this paper is to review and summarize odour legislation in selected European countries (France, Germany, Austria, Hungary, United Kingdom, Spain, The Netherlands, Italy, Belgium), North America (USA and Canada), South America (Chile and Colombia), as well as Oceania (Australia and New Zealand) and Asia (Japan, China). Many countries have incorporated odour controls into their legislation. However, odour-related assessment criteria tend to be highly variable between countries, individual states, provinces and even counties and towns. Legislation ranges from (1) no specific mention in environmental legislation that regulates pollutants which are known to have an odour impact to (2) extensive details about odour source testing, odour dispersion modeling, ambient odour monitoring, (3) setback distances, (4) process operations, and (5) odour control technologies and procedures. Agricultural operations are one specific source of odour emissions in rural and suburban areas and a model example of such complexities. Management of agricultural odour emissions is important because of the dense consolidation of animal feeding operations and the advance of housing development into rural areas. Overall, there is a need for continued survey, review, development, and adjustment of odour legislation that considers sustainable development, environmental stewardship, and socio-economic realities, all of which are amenable to a just, site-specific, and sector-specific application.

Nanocelluloses have gained significant attention in recent years due to singular properties (good biocompatibility, high optical transparency and mechanical strength, large specific surface area and good film-forming ability) and wide-ranging applications (paper, food packaging, textiles, electronics and biomedical). This article is a comprehensive review of nanocelluloses from the preparation methods to their applications in conservation and restoration of historical paper documents. The novelty lies in the information collected about nanocelluloses as renewable, environmentally friendly and sustainable materials in the field of preservation of cultural heritage as an alternative to conventional methods. Several studies have demonstrated that nanocelluloses, with or without other particles, impart to the paper documents excellent optical and mechanical properties, very good stability against temperature and humidity aging, stronger antibacterial and antifungal activity, high protection to UV light and do not require additional adhesive.

Using nanoparticles (NPs) in drug delivery has exhibited promising therapeutic potential 13 in various cancer types. Nevertheless, several challenges must be addressed, including the 14 formation of the protein corona, reduced targeting efficiency and specificity, potential immune 15 responses, and issues related to NP penetration and distribution within 3-dimensional tissues. 16 To tackle these challenges, we have successfully integrated iron oxide nanoparticles into 17 neuroblastoma-derived extracellular vesicles (EVs) using the parental labeling method. We first de- 18 veloped a tissue-engineered (TE) neuroblastoma model, confirming the viability and proliferation 19 of neuroblastoma cells for at least 12 days, supporting its utility for EV isolation. Importantly, EVs 20 from long-term cultures exhibited no differences compared to short-term cultures. Concurrently, 21 we designed Rhodamine (Rh), Polyacrylic acid (PAA)-functionalized magnetite nanoparticles 22 (Fe3O4@PAA-Rh) with high crystallinity, purity, and superparamagnetic properties (average size: 23 9.2 ± 2.5 nm). We then investigated the internalization of Fe3O4@PAA-Rh nanoparticles within 24 neuroblastoma cells within the TE model. Maximum accumulation was observed overnight while 25 ensuring robust cell viability. However, nanoparticle internalization was low. Taking advantage of 26 the enhanced glucose metabolism exhibited by cancer cells, glucose (Glc)-functionalized nanoparti- 27 cles (Fe3O4@PAA-Rh-Glc) were synthesized, showing superior cell uptake within the 3D model 28 without inducing toxicity. These glucose-modified nanoparticles were selected for parental labeling 29 of the TE models, showing effective NPs encapsulation into EVs. 30 Our research introduces innovative approaches to advance NPs delivery. By partially addressing 31 the challenges associated with 3D systems, optimizing internalization, and enhancing NPs stability 32 and specificity through EV-based carriers. Also, our findings hold the promise of more precise and 33 effective cancer therapies while minimizing potential side effects.

Transplanted rice cultivation has caused groundwater depletion in several regions globally. Direct-seeded rice under aerobic conditions is a water-saving alternative. However, under aerobic conditions, iron in the soil is oxidized from ferrous to ferric, which is not easily available for rice, resulting in iron deficiency induced chlorosis (IDIC) causing significant reduction in yield. Cultivated rice genotypes have limited variations for IDIC tolerance, while wild Oryza germplasm could be a potential source for IDIC tolerance. In this study, 313 Oryza accessions were evaluated for IDIC tolerance at the tillering stage under aerobic conditions and twenty IDIC tolerant lines were identified. The twenty lines showed no signs of chlorosis and had high levels of iron content and SPAD values, while eight cultivated controls exhibited varying degrees of chlorosis symptoms and low levels of SPAD and iron content. To confirm their tolerance, the selected lines were evaluated again in a subsequent year, and they showed comparable levels of tolerance indicating these lines were efficient in iron uptake and utilization resulted maintained high chlorophyll and leaf area index. These accessions may be useful for developing IDIC-tolerant cultivars for aerobic rice cultivation and future study of molecular basis of IDIC tolerance.

Mimosa acutistipula is endemic to Brazil and grows in ferruginous outcrops (canga) in Serra dos Carajás, eastern Amazon, where one of the largest iron ore deposits in the world is located. Plants that develop in these ecosystems are subject to severe environmental conditions and must have adaptive mechanisms to grow and thrive in cangas. Mimosa acutistipula is a native species used to restore biodiversity in post-mining areas in canga. Understanding the molecular mechanisms involved in the adaptation of M. acutistipula in canga is essential to deduce the ability of native species to adapt to possible stressors in rehabilitating minelands over time. In this study, the root proteomic profiles of M. acutistipula grown in a native canga ecosystem and rehabilitating minelands were compared to identify essential proteins involved in the adaptation of this species in its native environment and that should enable its establishment in rehabilitating minelands. The results showed differentially abundant proteins, where 436 proteins with significant values (p < 0.05) and fold change ≥ 2 were more abundant in canga and 145 in roots from the rehabilitating minelands. Among them, a representative amount and diversity of proteins were related to responses to water deficit, heat, and responses to metal ions. Other identified proteins are involved in biocontrol activity against phytopathogens and symbiosis. This research provides insights into proteins involved in M. acutistipula responses to environmental stimuli, suggesting critical mechanisms to support the establishment of native canga plants in rehabilitating minelands over time.

Reactions of Fe(II) with the tris-(pyridin-2-yl)ethoxymethane (py3C-OEt) tripodal ligand in presence of the pseudohalide ancillary NCE- (E = S, Se, BH3) ligands led to a series of three mononuclear complexes formulated as [Fe(py3C-OEt)2][Fe(py3C-OEt)(NCE)3]2·2CH3CN, with E = S (1), BH3 (2) and Se (3). Single crystal characterizations (complexes 1-2) and X-ray powder diffraction (complexes 1-3) reveal monomeric isomorph structures formed by the spin crossover (SCO) anionic [Fe(py3C-OEt)(NCE)3] complex, associated with the low spin (LS) cationic [Fe(py3C-OEt)2]2+ complex and two solvent acetonitrile molecules. In the [Fe(py3C-OEt)2]2+ cation, the Fe(II) is coordinated by two py3C-OEt tridentate ligands, while the [Fe(py3C-OEt)(NCE)3] anion displays a hexacoordinated environment involving three N-donor atoms of one py3C-OEt ligand and three nitrogen atoms arising from of the three (NCE) coligands. The magnetic studies show the presence of gradual SCO behavior for the three complexes: a one-step transition around 205 K for 1 and two step-transitions for compounds 2 and 3, centred at 245 K and 380 K for 2, and at 170 K and 298 K for 3. The magnetic behaviors of complexes 1 and 2 remain unchanged when heating up to 500 K, while complex 3 shows significant changes which are caused by the crystallisation solvent loss above room temperature.

Acinetobacter baumannii is a nosocomial pathogen capable of causing serious infections associated with high rates of morbidity and mortality. Due to its antimicrobial drug resistance profile, A. baumannii is categorized as an urgent priority pathogen by the Centers for Disease Control and Prevention in the United States and priority group 1 critical microorganism by the World Health Organization. Understanding how A. baumannii adapts to different host environments may provide critical insights into strategically targeting this pathogen with novel antimicrobial and biological therapeutics. Exposure to human fluids was previously shown to alter the gene expression profile of a highly drug susceptible A. baumannii strain A118 leading to persistence and survival of this pathogen. Herein, we explore the impact of human pleural fluid (HPF) and human serum albumin (HSA) on the gene expression profile of a highly multi-drug resistant strain of A. baumannii AB5075. Differential expression was observed for ~30 genes, whose products are involved in quorum sensing, quorum quenching, iron acquisition, fatty acid metabolism, biofilm formation, secretion systems and type IV pilus formation. Phenotypic and further transcriptomic analysis using quantitative RT-PCR confirmed RNA-seq data and pointed out a distinctive role of HSA as the molecule involved in A. baumannii response.

Maghemite (γ-Fe2O3) is a mineral formed from magnetite oxidation at low temperatures, an intermediate metastable term of the magnetite to hematite oxidation and could be mixed with both. It has magnetic susceptibility similar to magnetite, crystal structure close to magnetite with which it forms a solid solution, while compositionally it equals hematite. Maghemite is thus easily misidentified as magnetite by X-ray diffraction and/or as hematite by spot chemical analysis in iron ore characterization routines. Nonstoichiometric magnetite could be quantified in samples of Brazilian soils and iron ores by the Rietveld method using a constrained refinement of the X-ray patterns. The results were confirmed by reflected light microscopy and Raman spectroscopy, thus qualitatively validating the method. X-ray diffraction with the refinement of the isomorphic substitution of Fe2+ by Fe3+ along the magnetite-maghemite solid solution could help to suitably characterize maghemite in iron ores, allowing for the evaluation of its ultimate influence on mineral processing, by affecting its surface and breakage properties.

Ferric uptake regulation protein is a repressor protein which binds an AT rich region of DNA (the iron box). Fur binds as a dimer in a helix turn helix mode and it is activated by iron(II) and other divalent transition metal ions at elevated concentrations in a process to regulate the ion uptake. Each transition metal ion induces certain conformational changes to aid the Fur binding, both the N-terminal and C-terminal domains take part in binding to DNA in addition to His 88 and His 86 residues. The process is discussed in view of experimental reports. Fe(II), Mn(II) and Co(II) activate Fur to bind DNA experimentally but Zinc plays a structural role and does not activate Fur to bind DNA.

Currently, the use of sustainable chemistry as an ecological alternative for the generation of products or processes, free of polluting substance has assumed a preponderant role. The aim of this work is propose a bioinspired, facile, at low cost, non-toxic and environmentally friendly alternative to obtaining magnetic nanoparticles whit a majority phase of magnetite (Fe₃O₄). Is important to empathize that the synthesis was based on the chemical reduction through the Cnicus Benedictus extract, whose use as reducing agent has not been reported in the synthesis of iron oxides nanoparticles. In addition, the Cnicus Benedictus is abundant endemic plant in Mexico, with several medicinal properties and a large number of natural antioxidants. The obtained nanoparticles exhibited significant magnetic and antibacterial properties and an enhanced photocatalytic activity. The crystallite size of the Fe₃O₄ nanoparticles (Fe₃O₄ NP’s) was calculated by Williamson-Hall method. The photocatalytic properties of the Fe₃O₄ NP´s were studied by kinetics absorptions models in the Congo red (CR) degradation. Finally the antibacterial effect of the Fe3O4 NP´s were evaluated mediated the Kirby-Bauer method against E. coli and S. aureus bacteria. This route offers a green alternative to obtain Fe3O4 NP´s with remarkable magnetic, photocatalytic and antibacterial properties.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Every day around 93% of children under the age of 15 (1.8 billion children) breathe outdoor air that is so polluted it puts their health and development at serious risk. Due to the pandemic, however, ventilation of buildings using outdoor air has become an important safety technique to prevent the spread of COVID-19. With the mounting ev-idence suggesting that air pollution is impactful to human health and educational out-comes, this contradictory guidance may be problematic in schools with higher air pol-lution levels, but keeping kids COVID-19 free and in school to receive their education is now more pressing than ever. To understand if all schools in an urban area are ex-posed to similar outdoor air quality and if school infrastructure protects children equally indoors, we installed research grade sensors to observe PM2.5 concentrations in indoor and outdoor settings to understand how unequal exposure to indoor and out-door air pollution impacts indoor air quality among high- and low-income schools in Salt Lake City, Utah. Based on this approach, we found that during atmospheric inver-sions and dust events, there was a lag ranging between 35 to 73 minutes for the out-door PM2.5 concentrations to follow a similar temporal pattern as the indoor PM2.5. This lag has policy and health implications and may help to explain the rising concerns re-garding reduced educational outcomes related to air pollution in urban areas. These data and resulting analysis show that poor air quality may impact school settings, and the potential implications with respect to environmental inequality.

The provision requirement of 10% openings of the total floor area stated in the Uniform Building by Law 1984 Malaysia has been practiced by designers for building plan submission approval. However, the effectiveness of thermal performance in landed residential buildings, despite the imposition by the by-law, has never been empirically measured and proven. Although terraced houses in Malaysia have dominated 40.9% of the total property transaction in 2019, such mass production with typical designs hardly provides its occupants with thermal comfort due to the static outdoor air condition and lack of external windows, where the conventional ventilation technique does not work well, even for houses with an air well system. Consequently, the occupants need to rely on mechanical cooling, which is a high energy-consuming component contributing to outdoor heat dissipation and therefore urban heat island effect. Thus, encouraging more effective natural ventilation to eliminate excessive heat from the indoor environment is critical. Since most of the research focuses on simulation modelling lacking sufficient empirical validation, this paper drawing on field measurement investigates natural ventilation performance in terraced housing with an air well system. More importantly, the key concern as to what extent the current air well system serving as a ventilator is effective to provide better thermal performance in the single storey terraced house is to be addressed. By adopting an existing single storey air welled terrace house, the existing indoor environmental conditions and thermal performance were monitored and measured using scientific equipment, namely HOBO U12 air temperature and air humidity, the HOBO U12 anemometer and the Delta Ohm HD32.3 Wet Bulb Globe Temperature meter for a six-month duration. The findings show that the air temperature of the air well ranged from 27.48°C to 30.92°C, while the mean relative humidity were from 72.67% to 79.25%. The mean air temperature for a test room (single sided ventilation room) ranged from 28.04°C to 30.92°C with a relative humidity of 70.16% to 76%. These empirical findings are of importance, offering novel policy insights and suggestions to potentially revising the existing building code standard and by laws; since the minimum provision of 10% openings has been revealed to be less effective to provide a desired thermal performance and comfort, mandatory compliance with, and the necessity for, the bylaw requirement should be revisited and further studied.

To date, theoretical analyses have provided several useful methods/algorithms for studying transition states and non-covalent interactions. Potential Energy Scan (PES) is one such method that has found wide application in the physicochemical community. Analyzing the PES profiles of the catalytic system of FeBr3 in Electrophilic Aromatic Substitution (EAS) with molecular halogens, one can notice an obvious difference from the modern textbook mechanisms proposed in this area of study. Moreover, the newly presented Graphic Methodology (GM) allows a simple and reliable transition state determination even for very weakly bound charge transfer complexes using second-order derivatives as an efficient tool in the graphical analysis. Relative errors that can be reduced to a few parts per thousand in transition state estimation make this method a potentially very useful tool in further graphical studies of non-covalent interactions. Studies performed using high-precision semiempirical methods suggest that the process of halonium ion quenching proceeds along a completely different pathway, suggesting a possible novel transition metal-nonmetal catalytic system involved in the EAS electrophilic quenching step. The results presented here strongly suggest a future GM application that is widely used and the introduction of pseudo and pre-transition states as new terms in the description of non-covalent interactions.

The aim of this work is to provide a full description of how air temperature and solar radiation induce changes in the land cover over an Antarctic site. We use shortwave broadband albedo (albedo integrated in the range 300-3000 nm) from a spaceborne sensor and from field surveys to calculate the monthly relative abundance of landscape units. Field albedo data were collected using a portable albedometer over seven landscape units: clean fresh snow; clean old snow; rugged landscape composed of dirty snow with disperse pyroclasts and rocky outcrops; dirty snow; stripes of bare soil and snow; shallow snow with small bare soil patches; bare soil. MODIS MCD43A3 daily albedo product was downloaded using the Google Earth Engine API from the 2000-2001 season to the 2020-2021 season. Each landscape unit was characterized by an albedo normal distribution. The monthly relative abundance of the landscape units were calculated by fitting a linear combination of the normal distributions to the histogram of the MODIS monthly mean albedo. The monthly relative abundance of the landscape unit consisting of rugged landscape composed of dirty snow, with dispersed clasts and small rocky outcrops exhibits a high linear positive correlation with the monthly mean albedo (R2=0.87) and a high linear negative correlation with the monthly mean air temperature (R2= 0.69). The increase of the solar radiation energy flux from September to December coincides with the decrease of the relative abundance of the landscape unit composed of dirty snow with dispersed clasts and small rocky outcrops. We propose a mechanism to describe the evolution of the landscape: uncovered pyroclasts act as melting centres favouring the melting of surrounding snow. Ash does not play a decisive role in the melting of the snow. The results also explain the observed decreasing of the thaw depth of the permafrost on the island in the period 2006-2014, resulting from an increase in the snow cover over the whole island.

Different coffee drying technologies face complex task in ensuring an acceptable final seed moisture content. Drying technology of agricultural commodities aims to maintain and improve the quality of the agricultural products themselves. In addition to maintaining quality, especially from other bacterial attacks, it can last for a long time before further processing. Coffee commodities are promising for the welfare of coffee farmers. Drying technology plays a major role in determining the quality of coffee. Various drying models are applied including the traditional model that until now is still applied, direct drying under solar radiation. However, this drying process is less hygienic and requires a large area. Thus, one of the drying technologies that can accelerate drying time is to vary the air flow in the drying chamber so that the coffee can be determined to reduce the water content with a certain temperature. In this study, it was found that the moisture content of coffee beans dried using a dryer on air flow with variations of velocity in solar collector 1 (DB1) air velocity of 1.0m/s obtained the final mass = 732.249 gr, solar collector 2 (DB2) with air velocity 1.5 m/s obtained the final mass = 774.70 gr, solar collector 3 (DB3) with air velocity 2.0 m/s obtained the final mass = 855.10 gr, solar collector 4 (DB4) with air velocity 2.5 m/s obtained the final mass = 745.79 gr, and solar collector 5 (DB5) with air velocity 3.0 m/s obtained the final mass = 786.40 gr. Water Content DB1=12.0%, DB2=13.6%, DB3=18.5%, DB4=12.9% and DB5=15.2%. The time required for 25 hours with a maximum radiation of 586.9 w/m2, total heat utilized from solar radiation in 3 days =16.663128 MJ/m2. from the initial weight of 1500gr coffee bean samples and dried in five solar collectors with parallel simultaneously. The evaporated water content DB1=51.18%, DB2=48.35%, DB3=42.96%, DB4=50.28% and DB5=47.57%. Based on this research, it was found that the most optimum quality of coffee was by using solar collector 2 (DB2), namely with air flow of 1.5 m/s with average temperature in the drying box DB2=43.68°C, with the quality content of the coffee, Protein content=12.2%, Carbohydrate=22.8% and Free Fatty Acid (ALB) content=0.05%.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

The outbreak of the COVID-19 pandemic has raised concerns about potential environmental factors that could influence the spread and severity of the SARS-CoV-2 virus. Atmospheric pollution, particularly particulate matter (PM), has been suggested as a contributing factor to viral infections and respiratory complications. This two-year observational study aimed to investigate the relation between air pollution and the spread of COVID-19, focusing on PM2.5. Unlike previous studies limited to specific cities or countries, inevitable to use temporal data. Our research analyzed data from various states across the United States, considering both spatial and temporal correlation. The analysis considered the number and geographic distribution of COVID-19 cases along with daily PM2.5 exposure levels, accounting for monthly average PM2.5 exposure, from March 2020 to December 2021. The observed conflicting results of the temporal and spatial correlation present challenges for researchers in understanding the true nature of the relationship between PM2.5 air pollution and COVID-19 cases. The correlation between various factors, such as population density, PM2.5, temperature, and wind speed, and COVID-19 refers to an association or statistical relationship, not causation. Moreover, the intricate interplay of these variables makes it difficult to establish a clear cause-and-effect relationship.

The research considers creating a network of moss-based biotechnological purification filters in the Smart City concept. The extent of absorption of heavy metals and gases by Sphagnopsida moss under different conditions was investigated. The efficiency of air purification with biotechnological filters was also investigated using the example of the city of Almaty, Republic of Kazakhstan, where an excess of the permissible concentration of harmful substances in the air, according to the WHO air quality guidelines, is recorded throughout the year. Data on the level of pollution recorded by sensors located in the biggest Kazakhstani cities from 06/21/2020 to 06/04/2023 were selected as the basis for calculating the efficiency. In total, there are two hundred twenty sensors in 73 settlements of the Republic of Kazakhstan, with 80 such sensors located in the city of Almaty. Since creating a single biotechnological filter is expensive, the task was to calculate the air purification effect in the case of increasing the number of filters placed in polluted areas. As a result, it is shown that ten filters provide an air purification efficiency of 0.77%, 100 filters 5.72%, and 500 filters 23.11%. A biotechnological filter for air purification based on moss was designed at Astana IT University, considering the climatic features, distribution, and types of pollution in the Republic of Kazakhstan. The obtained results are essential for ensuring compliance with the ISO 37120:2018 standard for environmental comfort in the Republic of Kazakhstan. Additionally, the research findings and the experience of implementing a moss-based biotechnological filter can be applied to designing similar air purification systems in other cities. This is of great importance for the advancement of the field of urban science.

Air pollution is a man-made environmental-related problem and has importance globally among all environmental issues. It is described as an atmospheric situation in which several components appear at high attention above their ambient level and generate a quantifiable effect on vegetation, animals, and people. Air pollution and its control are a universal problem and have become an issue of great trouble for us in current years. However, monitoring and measurement of the concentration of air pollutants are most difficult in assessment to monitoring other components in the environment. Air pollutants are transported to polar regions by different mechanisms such as long-range atmospheric transport or grasshopper effects and via anthropogenic activities. After reaching the polar regions, they settle down and remain as such for a long-time due to their persistent nature. They can distress the environment and wildlife of the polar regions. Generally, dangerous chemicals may cause a risk of well-being effects, whereas lethal pollutants focus on one physiological reaction. We reviewed the available information on air pollution (occurrence, sources, and harmful effects) in the polar regions.

Rationale: The possible effect of Particulate Matter (PM10 and PM2.5 of diameter 10 and 2.5 µm respectively) levels on Covid-19 mortality is now well established. However, time-evolution of Covid-19 mortality according to PM2.5 levels has been scarcely investigated. Aim: To understand this relationship at the European level for the period 2020 (beginning) - 2022 (end). Methods: 16 representative locations in Europe (81 million people) with heterogeneous levels of PM2.5 (µg.m-3), from low to high. PM2.5 levels were assessed by various methods, and Covid-19 mortality was reported by Johns Hopkins University. Results: The trend of Covid-19 mortality vs. PM2.5 levels varied among locations. Overall, the estimated mean value was of a 40±20% mortality increase per 1 µg.m-3 PM2.5 increase. The stronger the positive gradient of the PM peak, the stronger the positive gradient of the Covid-19 mortality. Exposure to several PM peaks during about a 2-month period was the main contributor to Covid-19 mortality increases. Conclusion: Our data confirm a temporal relation between PM2.5 exposure and Covid-19 mortality, considering a 2-month integration-time for pollution events. Number-concentrations of PM should be used in the future rather than the PM2.5 mass-concentrations (µg.m-3) with the consideration of PM composition to better explain this finding.

Exposure to air pollution have detrimental effects on the elderly, women, people with pre-existing medical conditions, people living in poverty and children. The aim of the study was to investigate the extent of community awareness and knowledge on the health risks associated with exposure to air pollution. A cross-sectional study design was used for the study, using self-administered questionnaires. A simple random sampling technique was used to select 376 respondents. Systematic sampling method was applied to select the households. SPSS version 26 was used to analyze data. Of 376 respondents, 221 were males and 154 females. 113 were aged between 23-47years and 353 were aware that if they don’t protect themselves against polluted air, they may get sick, with age and educational status associated with their awareness (p &lt; 0.05). About 361 knew what air pollution is and 188 think the air they breathe in Annadale is moderate. A total number of 278 said they feel sick/uncomfortable when the quality of air is bad. About 293 knew that people are exposed to air pollution by breathing contaminated air and 237 identified sewage smell as the main cause of air pollution. Respondents who identified internet and television as the main source of information were 199 and 177 respectively. Those who were not aware of actions implemented to reduce air pollution were 180. Based on the results of the study, respondents are aware of the dangers of exposure to polluted air, and it is necessary that air pollution risk communication strategies be implemented to empower residents.

The representation of aerosols in climate-chemistry models is important for air quality and climate change research, but it can require significant computational resources. To overcome this, simpler modules such as modal aerosol modules with three lognormal modes (MAM3) can be used. In this study, the coupling of the Carbon Bond Mechanism, version Z (CBMZ), and MAM3 chemistry modules in WRF-CAM5 was improved by adding biomass-burning emissions to both gas- and particle-phase chemistry and incorporating a conversion mechanism between volatile organic compounds (VOCs) and secondary organic carbons (SOCs). The study conducted six simulations over the western U.S. and northeastern Pacific region and compared the model’s performance with observational benchmarks such as reanalysis, ground-based, and satellite data. The results showed that the model with enhanced chemistry capabilities had a 31% and 58% reduction in root-mean-square errors (RMSE) for black carbon (BC) and organic carbon (OC) surface concentrations, respectively. The earlier release of the WRF-CAM5 version had two deficiencies that were addressed in this study. This research highlights the importance of accurate aerosol representation in climate-chemistry models for improving accuracy and reducing errors in simulations.

Hot air frying is a new method of frying food, where the use of a small amount of oil is optional but recommended. The objective of this review was to know the state of the art of hot air frying technology, focusing on trends, and thus obtain new ideas for future work in this area of food. In conclusion, the availability of advanced devices will increase the demand for hot air fryers as demonstrated by the trend generating a great economic and social impact. This new technology not only provides health benefits, but also has environmental advantages. In addition, work focusing on food (i.e. tortilla chips, plantain chips, eggs and meats) is recommended, since there are not enough studies on the subject. Currently, research is being conducted on home fryers, so the use of fryers and their impact at the industrial level is a developing area that will require further research.

This document serves as supplemental information to Shapero et al. (2023), which is itself a comment on Nowell et al. (2022). Environmental Health Perspective’s publishing standards for article comments have strict word counts and do not allow the addition of new primary data analyses; therefore, this document provides an additional level of detail and supporting analyses that serve as an important backup to and expansion of Shapero et al. (2023) and that also respond to some comments within the author’s reply to our comments (Holmes and Nowell, 2023). Nowell et al. (2022) evaluated potential PM_2.5 community impacts from sugarcane harvesting. However, their analysis is flawed by erroneous assumptions and misapplied technical approaches, as discussed in Shapero et al. (2023) and as detailed in this supplemental information document. Additionally, the authors ended their analysis with 2018 data, but later data shows no marginal increase in PM_2.5 during sugarcane harvest following 2019 even using the authors’ approach (Holmes and Nowell, 2023). Therefore, the authors’ evaluations have no relevance to current conditions. Nonetheless, even their evaluation and conclusions regarding PM_2.5 concentrations purportedly attributable to sugarcane harvesting prior to 2019 are unsupported and technically unsound as detailed below.

The climate change impacts on some regions of the planet faster and stronger. These areas are known as the hot spots for climate change and Cyprus (Nicosia) in the Mediterranean is one of these spots. This paper aims to analyze the significant changes of atmospheric aerosol characteristics in 2019 and during the extreme event of 25 April 2019. We study the aerosol optical thickness (AOT), Ångström exponent, single scattering albedo, refractive index (imaginary and real parts), size, and vertical distribution of aerosol particles during the event of a high atmospheric aerosol contamination over Nicosia in details. For this purpose, we used the ground-based lidar, observations of the sun-photometer AERONET Nicosia station, satellite products from the Moderate Resolution Imaging Spectroradiometer (MODIS), and back trajectories of air movements calculated using the Hybrid Single Particle Lagrangian Integrated Trajectory Model (HYSPLIT). On 23–25 April, according to lidar and sun-photometer observations, strong aerosol pollution over Nicosia was detected. On April 25, 2019, the AOT value exceeds 1.0 at λ = 440 nm. Analysis of the optical and microphysical characteristics supported that the pollution consists of mainly Saharan dust and partly urban aerosols. This assumption was confirmed by HYSPLIT backward trajectories and MODIS images where air masses containing dust particles came from North Africa and from the Eastern part of Europe.

Air pollution is a serious global issue, responsible for approximately one in every nine deaths each year, ranking it among the greatest environmental hazards to human health. It is of particular concern in urban areas, where elevated pollutant concentrations and potential sufferers converge. Over one half of the world’s population presently lives in urban areas, and the urban population ratio is expected to reach 68% by 2050. Common air pollutants include particulate matter (PM), sulphur dioxide (SO2), ground-level ozone (O3), nitrogen oxide (NOx) and carbon monoxide (CO). While elevated rates of air pollution pose serious health risks for humans, outdoor plants can help reduce the harmful effects of air pollution by filtering and purifying the air around us.In this project Common Ivy, Aster and Miniature Andromeda plants were evaluated for air pollutant mitigation. In this study we developed a vegetation barrier model with the plant located in the middle of the greenhouse box, and air pollutant was sprayed on one side of the plant. Dispersion patterns of sprayed pollutants were tested with and without vegetation barrier. Measurements of carbon dioxide (CO2), Formaldehyde (HCHO), Total Volatile Organic Compounds (TVOC), and Particulate Matter (PM2.5/PM10) were taken before spraying, then at 0 and 30 minutes after spraying, using both monitors.The results show mitigation rates (in 177 ft3 of air after 30 min): for TVOC the minimum reduction is 5 mg/m3; for HCHO, 1 mg/m3; for CO2, 2000 ppm; for PM2.5, 2000 ug/m3; and for PM10 it was 1000 ug/m3.

The mass composition of Particulate Matter (PM) with an aerodynamic diameter of 2.5 microns (PM2.5) in San Joaquin Valley (SJV) is dominated by ammonium nitrate (NH4NO3) which is a secondary pollutant. The goal of this research was the investigation of the relationship between emissions, meteorology and PM2.5 concentrations in Fresno for the winter season. It was found that the location of sites near emission sources such as freeways compared with residential sites strongly affected measured PM2.5 concentrations. It was found that although long-term trends showed declines in both emissions and PM2.5 concentrations there was substantial variability between the years in the PM2.5/emissions relationship. Much of the yearly variation in the relationship between emissions and PM2.5 concentrations can be attributed to yearly variations in weather, such as atmospheric stability, precipitation frequency and average wind speed. There are moderate correlations between PM2.5 concentrations and temperature differences between nearby surface stations at varying elevations which explains some of the daily and seasonal variation in PM2.5. Occurrence of precipitation was related to low PM¬2.5 although the higher wind speeds and lower atmospheric stability associated with precipitation likely explain some of the low PM2.5 as well as washout of PM.

International literature data report that the increase of infectious risk may be due to heating, ventilation and air conditioning (HVAC) systems contaminated by airborne pathogens. Moreover, the presence of complex rotating dehumidification wheels (RDWs) may complicate the cleaning and disinfection procedures of the HVAC systems. We evaluated the efficacy of a disinfection strategy applied to the RDW of two hospitals HVAC systems. Hospitals have 4 RDW systems related to the surgical areas (SA1 and SA2) and to the intensive and sub-intensive cares (IC and sIC). Microbiological air and surfaces analysis were performed in HVAC systems, before and after the disinfection treatment. Hydrogen peroxide (12%) with silver ions (10 mg/L) was aerosolized in all the air sampling points, located close to the RDW device. After the air disinfection procedure, reductions of total microbial counts at 22°C and fungi were achieved in SA2 and IC HVAC systems. An Aspergillus fumigatus contamination (6 CFU/500L), detected in one air sample collected in the IC HVAC system, was eradicated after the disinfection. Surface samples proved a good microbiological quality. Results suggest the need of a disinfection procedure aimed to improve the microbiological quality of the complex HVAC systems, mostly in surgical and intensive care areas.

The Cosmic-Ray Extremely Distributed Observatory (CREDO) is a project dedicated to global studies of extremely extended cosmic-ray phenomena, the cosmic-ray ensembles (CRE), beyond the capabilities of existing detectors and observatories. Up to date cosmic-ray research has been focused on detecting single air showers, while the search for ensembles of cosmic-rays, which may overspread a significant fraction of the Earth, is a scientific terra incognita. Instead of developing and commissioning a completely new global detector infrastructure, CREDO proposes approaching the global cosmic-ray analysis objectives with all types of available detectors, from professional to pocket size, merged into a worldwide network. With such a network it is possible to search for evidences of correlated cosmic-ray ensembles. One of the observables that can be investigated in CREDO is a number of spatially isolated events collected in a small time window which could shed light on fundamental physics issues. The CREDO mission and strategy requires active engagement of a large number of participants, also non-experts, who will contribute to the project by using common electronic devices (e.g. smartphones). In this note the status and perspectives of the project is presented.

Livestock farming is a major source of greenhouse gas and ammonia emissions. In this study, we estimate methane, nitrous oxide and ammonia emission from livestock sector in the Red River Delta region from 2000 to 2015 and projection to 2030 using IPCC 2006 methodologies with the integration of local emission factors and provincial statistic livestock database. Methane, nitrous oxide and ammonia emissions in 2030 are estimated at 132 kt, 8.3 kt and 34.2 kt, respectively. Total global warming potential is 9.7 MtCO_2eq in 2030, accounts for 33% greenhouse gas emissions from livestock in Vietnam. Pig farming is responsible for half of both greenhouse gases and ammonia emissions in the studied region. Other major livestock for greenhouse gas emission is cattle and for ammonia emission is poultry. Hanoi contributes for the largest emissions in the region in 2015 but will be caught up and surpassed by other provinces in 2030.

Air pollution has become a growing invisible killer in recent years and is major cause of morbidity and mortality globally. India stands 10th among the highly polluted countries with an average PM10 level of 134μg/m3 per year. It is also reported that 99% of India's population comes across air pollution level that exceed the World Health Organization Air Quality Guideline (AQG), PM2.5 permissible levels of 10 μg/m3. Maternal exposure to air pollution has a serious health outcome to the offspring because it can affect embryonic phases of development during the gestation period. Fetus is more prone to air pollution effect during embryonic developmental phases due to oxidative stress as antioxidant mechanisms are lacking at that stage. Any injury during this vulnerable period (embryonic phase) will have long-term impact on offspring health both in early and later in life. Epidemiological studies have revealed that maternal exposure to air pollution increases the risk of developing airways disease in offspring due to impaired lung development in utero. In this review, we discuss cellular mechanisms involved in maternal exposure to air pollution and how it can impact development of airways disease in offspring. Better understanding of these mechanisms in context of maternal exposure to air pollution can offer newer avenue to prevent development of airways disease in offspring.

Abstract: Air-polishing with low abrasiveness powders is fats arising as a valid and mini-invasive instrument for the management of biofilm colonizing dental implants. The reported advantage is the efficient removal of plaque with respect of the titanium integrity. In the present study, we evaluated the in-situ plaque-removal and continual the post-treatment anti-bacterial efficacy of an innovative erythritol/chlorhexidine air-polishing powder and compared it with sodium bicarbonate. Two peri-implantitis-linked biofilm formers strains Staphylococcus aureus and Aggregatibacter actinomycetemcomitans were selected and used to infect titanium disks before and after the air-polishing treatment. Cells number and viability were assayed by colonies forming units (CFUs) count and metabolic-colorimetric (2,3-Bis-(2-Methoxy-4-Nitro-5-Sulfophenyl)-2H-Tetrazolium-5-Carboxanilide) (XTT) assay. Air-polishing performed with either sodium bicarbonate or erythritol/chlorhexidine was effective in reducing bacteria biofilm viability and number onto pre-infected specimens, while erythritol/ chlorhexidine showed a higher post-treatment biofilm re-growth inhibition. Surface analysis via mechanical profilometry failed to show an increase in titanium roughness, regardless of the powder selected.

The ambient air quality data for particulate matter as well as criteria of gaseous pollutants were assembled during December 2013 to December 2015 from the Continuous Air Quality Monitoring Station (CAMS) located at Agrabad, Chittagong. The observation showed that during April- October, 24 hour average concentration of PM10 and PM2.5 were within the National Ambient Air Quality Standard (NAAQS) level but it increased occasionally by more than two and a half times during the whole non-monsoon period (November-March). The highest values found of PM2.5 were 321.1 µg/m³ in January, 2013 and 220.34 µg/m³ in December 2015. Whether, the highest alarming concentration of PM10 was reported as 474 µg/m3 in January 2007. The other gaseous pollutants such as SO₂, NO₂, O₃, CO and Hydrocarbons remain well within the permissible limit except dry non-monsoon period. The yearly average increase of Air Quality Index (AQI) value indicates the growth rate of air pollution in Chittagong city. The main responsible pollutant for air pollution is found PM_2.5.

Estimating the infection risks in indoor environments comprises the assessment of the behavior of virus-laden aerosols, i.e. spreading, mixing, removal by air purifiers etc. A promising experimental approach is based on using non-hazardous surrogate aerosols of similar size, e.g. salt particles, to mimic the virus aerosol behavior. This manuscript addresses the issue how a successful transfer of such experiments can be accomplished. Corresponding experiments in two very different environments, a large community hall and a seminar room, with optional use of air purifiers in various constellations were conducted. While high particle concentrations are advantageous in terms of avoiding influence of background aerosol concentrations, it is shown that appropriate consideration of aggregation and settling are vital to theoretically describe the experimentally determined course of particle concentrations. A corresponding model equation for a well-mixed situation is derived and the required parameters are thoroughly determined in separate experiments independently. It is demonstrated that clean air delivery rates (CADR) of air purifiers determined with this approach may differ substantially from common approaches not explicitly taking into account aggregation.

This study aimed to develop multifunctional nanoplatforms for both cancer imaging and therapy using superparamagnetic iron oxide nanoparticles (SPIONs). Two distinct synthetic methods, reduction-precipitation (MR/P) and co-precipitation at controlled pH (MpH), were explored, including the assessment of coating’s influence, namely dextran and gold, on their magnetic properties. These SPIONs were further functionalized with gadolinium to act as dual T1/T2 contrast agents for magnetic resonance imaging (MRI). Parameters such as size, stability, morphology, and magnetic behavior were evaluated by a detailed characterization analysis. To assess their efficacy in imaging and therapy, relaxivity and hyperthermia experiments were performed, respectively. The results revealed that both synthetic methods lead to SPIONs with similar average, 9 nm. Mössbauer spectroscopy indicated that samples obtained from MR/P consist of approximately 11-13% of Fe present in magnetite, while samples obtained from MpH have higher content, of 33%-45%. Despite coating and functionalization, all samples exhibited superparamagnetic behavior at room temperature. Hyperthermia experiments showed increased SAR values with higher magnetic field intensity and frequency. Moreover, the relaxivity studies suggested potential dual T1/T2 contrast agent capabilities for the coated SPpH-Dx-Au-Gd sample, thus demonstrating its potential in cancer diagnosis.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

Children with history of prematurity are at higher risk of complications, comorbidities and iron deficiency. In this study we assess the prevalence of restless sleep disorder, as well as that of periodic leg movements during sleep (PLMS) in these children. Retrospective chart review of sleep studies in children aged 1-18 years, with history of prematurity. Only diagnostic studies in children without diagnosis of a genetic syndrome or airway surgery or tracheostomy were included. Three groups were compared, children with PLMS index&gt;5, children with restless sleep disorder (RSD), and children with neither elevated PLMS index nor RSD. During the study, 2,577 sleep studies were conducted. Ninety-two studies fit our criteria and were included in analysis. Median birth age was 31 weeks, interquartile range (IQR) 27-34 weeks. Thirty-two (34.8%) children were referred for restless sleep and 55 (59.8%) for snoring; after polysomnography 18% were found to have PLMS index &gt;5/hour, 14% fit the criteria for RSD. There were no statistically significant differences in polysomnographic parameters between the children with RSD, PLMS and the remaining group, except for lower obstructive apnea/hypopnea index (Kruskal-Wallis ANOVA 8.621, p=0.0135) in the RSD group (median 0.7, IQR 0.3-0.9) than in the PLMS (median 1.7, IQR 0.7-3.5), or than in the nonRSD/nonPLMS group (median 2.0, IQR 0.8-4.5). There was elevated frequency of RSD and elevated PLMS in children with history of prematurity that might be linked to the increased risk of iron deficiency in premature infants. These new results add new knowledge on the prevalence of RSD in these children.

The reference method for cefiderocol antimicrobial susceptibility testing is broth microdilution (BMD) with iron-depleted-Mueller-Hinton (ID-MH) medium, whereas breakpoints recommended for disk diffusion (DD) are based on MH-agar plates. We aimed to compare the performance of the commercial BMD tests ComASP (Liofilchem) and UMIC (Bruker), DD and E-test using MH- and ID-MH-agar plates with the reference BMD method using 100 carbapenem-resistant-A. baumannii isolates. Standard BMD was performed according to the EUCAST guidelines, DD and E-test were carried out using two commercial MH-agar plates (bioMérieux and Liofilchem) and an in-house ID-MH-agar plate, while ComASP and UMIC were performed according to the manufacturer’s guidelines. DD performed with the ID-MH-agar plates led to a higher categorical agreement (CA, 95.1%) with standard BMD and fewer categorization errors compared to the commercial MH-agar plates (CA bioMérieux 91.1%, Liofilchem 89.2%). E-test on ID-MH-agar plates exhibited a significantly higher essential agreement (EA, 75%) with standard BMD compared to the two MH-agar plates (EA bioMérieux 57%, Liofilchem 44%), and showed a higher performance in detecting high-level resistance than ComASP and UMIC (mean log2 difference with standard BMD for resistant isolates of 0.5, 2.83 and 2.08, respectively). In conclusion, DD and E-test on ID-MH-agar plates exhibit a higher diagnostic performance than on MH-agar plates and the commercial BMD methods. Therefore, we recommend using ID-MH-agar plates for cefiderocol susceptibility testing of A. baumannii.

Mn-promoted bulk iron catalysts with high specific surface area (82-211 m2.g-1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation reaction. The Mn-promoted iron catalysts showed better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction of iron oxide, better carburization of iron oxides and higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe ratio of 0.05). Upon steady-state conditions (T=340 ºC, total pressure of 20 bar and H2/CO2=3), this catalyst showed high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst shows high stability during 72 h of reaction related to low amount of soft coke formation and catalyst activation through the formation of χ-Fe5C2 phase during the on-stream reaction.

All living organisms require some metal ions for their energy production as well as metabolic and biosynthetic processes. Within cells, metal ions are involved in the formation of adducts interact with metabolites and macromolecules (proteins and nucleic acids). The proteins that require binding to one or more metal ions to be able to carry out their physiological function are called metalloproteins. About one third of all protein structures in the Protein Data Bank involve metalloproteins. Over the past few years there has been a tremendous progress in the number of computational tools and techniques making use of 3D structural information to support the investigation of metalloproteins. This trend has been boosted also by the successful applications of neural networks and deep learning approaches in molecular and structural biology at large. In this review, we discuss recent advances in the development and availability of resources dealing with metalloproteins from a structure-based perspective. We start by addressing tools for the prediction of metal-binding sites (MBSs) using structural information on apo-proteins. Then, we provide an overview of methods for and lessons learned from the structural comparison of MBSs in a fold-independent manner. We then move to describing databases of metalloprotein/MBS structures. Finally, we summarize recent DL applications enhancing the functional interpretation of metalloprotein structures.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

(200 words) Imidazolium ionic liquids containing acetylacetone, thenoyltrifluoroacetone, or 8-hydroxyquinoline, respectively, were used as the extracting agents for the separation of traces of iron (III) from its aqueous solutions with or without citric and oxalic acids. The results show that 8-hydroxyquinoline in imidazolium ionic liquids extract iron quantitatively from all the tested solutions including complexing ones, regardless indications of unexpected iron behavior/speciation.

Assuming that climate warming in the WSL will lead to a northward shift of the forest and permafrost boundaries, a “substituting space for time” approach predicts an increase in concentration of DIC and labile major and trace elements and a decrease of the transport of DOC and low soluble trace metals in the form of colloids in the main stem of the Ob River. However, an unknown factor is the change in hydrochemistry of the largest southern tributary, the Irtysh River, which is impacted by permafrost-free steppe and forest-steppe zone. Overall, seasonally-resolved transect studies of large riverine systems of western Siberia are needed to assess the hydrochemical response of this environmentally-important territory to on-going climate change.

There is a marked momentum towards the use of clean hydrogen energy as an alternative for fossil fuels. Renewable energies such as solar and wind are being used to generate hydrogen from the water hydrolysis process. Indeed, this approach stores renewable energies in the form of combustible hydrogen for other energy uses. The other alternative that could be economically more cost-effective at the current technology stage is to explore the natural “Hydrogen System” where the natural hydrogen is generated and accumulated within the earth system, the same that stands for a “Petroleum System”. The Discovery of a large accumulation of relatively pure natural hydrogen (H2) in Mali has triggered the opportunity of searching for natural hydrogen accumulations in other countries. The generation of hydrogen from a circular depression in Mali and some other countries is linked to the presence of geologically very old iron-rich basement rocks. Solid-liquid redox reactions between iron-rich minerals and groundwater that split water are a possible source of H2 in deep basement rocks. It is believed that the hydrogen degassing may be detected by surface topographic circular to sub-circular shallow depressions. Chemical processes such as dissolution by hydrogen are considered to play the main role in the formation of the circular depressions through preferential vertical hydrogen migration channel. Archean iron-rich Yilgarn Craton that covers a vast area of Western Australia (WA) contains abundant iron-rich mafic-ultramafic rocks. The craton reveals many surficial circular depressions visible through satellite images. The area has abundant fault systems and is blanketed with Eocene sedimentary rocks containing high-quality reservoir rocks. All these characteristics seem to provide most of the required elements, such as hydrogen source, migration pathway, and reservoir rock for a “Hydrogen System” in this area.

Background: Besides anemia, iron deficiency may cause more subtle symptoms including those of the restless legs syndrome (RLS), the chronic fatigue syndrome (CFS) or sleeping disorders. Objective: The aim of this pre-planned secondary analysis was to compare the frequency and severity of symptoms associated with iron deficiency before and after (intravenous or oral) iron supplementation in iron deficient blood donors. Methods/Design: Prospective, randomized, controlled, single centre trial. (ClinicalTrials.gov: NCT01787526). Setting: Tertiary care center in Graz, Austria Participants: 138 female and 38 male whole blood and platelet apheresis donors aged ≥18 and ≤65 years with iron deficiency (ferritin ≤30ng/ml at the time of blood donation). Interventions: Intravenous iron (1 g ferric carboxymaltose, n=86) or oral iron supplementation (10 g iron fumarate, 100 capsules, n=90). Measurements: Clinical symptoms were evaluated by a survey before iron therapy (visit 0, V0) and after 8-12 weeks (visit 1, V1) including questions about symptoms of RLS, CFS, sleeping disorders, quality of life and symptoms like headaches, dyspnoea, dizziness, palpitations, pica and trophic changes of fingernails or hair. Results: We found a significant improvement in the severity of symptoms for RLS, fatigue and sleep quality (p<0.001). Furthermore, a significant decrease of headaches, dyspnoea, dizziness and palpitations was reported (p<0.05). There was no difference between the type of iron supplementation (intravenous versus oral) and clinical outcome data. Conclusion: Iron supplementation in iron deficient blood donors may be an effective strategy to improve symptoms related to iron deficiency and the wellbeing of blood donors.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

The pollen content of honey samples collected in the years 2017 and 2019 from experimental apiaries of Melipona seminigra pernigra Moure & Kerr 1950 installed in campo rupestre on canga (CRC) vegetation of the Serra dos Carajás, southeastern Amazonia, was analyzed to understand the local variability of floral resources occurring on natural and disturbed areas. Around one hundred pollen types were identified mainly belonging to Fabaceae, Myrtaceae and Euphorbiaceae (31, 6 and 5 types, respectively). The N5 mine presented the highest pollen richness with 95 pollen types identified, almost twice of those identified in the other areas, including the better preserved ones. Eighty percent of the pollen types are rare with concentrations ≤ 2,000 pollen grains/10 g; the remaining types are the most abundant and frequent, and are considered the primary bee sources (PBS). PBS correspond mostly to native plants such as Tapirira guianensis Aubl., Protium spp., Aparisthmium cordatum (A.Juss.) Baill., Mimosa acutistipula var. ferrea Barneby, Periandra mediterrânea (Vell.) Taub., Miconia spp., Pleroma carajasense K.Rocha, Myrcia splendens (Sw.) DC., Serjania spp. and Solanum crinitum Lam. All pollen types were identified during both seasons, but higher pollen concentration are related to the dry period (June-September). The statistical analysis indicated that there was no significant difference in honey pollen data between the natural and disturbed areas since the plant species considered as PBS in this work are intensively used in revegetation of degraded area (RDA) processes by mining activities.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

The common dry bean (Phaseolus vulgaris L.) is a nutrient dense food produced globally as a major pulse crop for direct human consumption, and is an important source of protein and micronutrients for hundreds of millions of people across Latin America, the Caribbean and Sub-Saharan Africa. Beans require large amounts of heat energy and time to cook, deterring consumers worldwide from purchasing beans. In regions where consumers rely on expensive fuelwood for food preparation, the yellow bean is often marketed as fast cooking. A Yellow Bean Panel (YBP) was assembled to explore the cooking time and health benefits of the five major seed types within the yellow bean market class (Amarillo, Canary, Manteca, Mayocoba, Njano) over two field seasons. This study shows how the Manteca yellow bean possess a fast cooking phenotype, which could serve a genetic resource for introducing fast cooking properties into a new generation of dry beans with cooking times < 20 minutes when pre-soaked and < 80 minutes unsoaked. Nutritional evaluation revealed fast cooking yellow beans have high iron retention (>80%) after boiling. An in vitro digestion/Caco-2 cell culture bioassay revealed a strong negative association between cooking time and iron bioavailability in the YBP (r values > -0.73). When either pre-soaked or left unsoaked the highest iron bioavailability scores were measured in the fast cooking Manteca genotypes providing evidence that this yellow market class is worthy of germplasm enhancement through the added benefit of improved iron quality after cooking.

Sentinel lymph node dissection (sLND) using a magnetometer and superparamagnetic iron oxide nanoparticles (SPIONs) as a tracer was successfully applied in prostate cancer (PCa). Radioisotope-guided sLND combined with extended pelvic LND (ePLND) achieved better node removal, increasing the number of affected nodes or the detection of sentinel lymph nodes outside the established ePLND template. We determined the diagnostic value of additional magnetometer-guided sLND after intraprostatic SPION-injection in high-risk PCa. This retrospective study included 104 high-risk PCa patients (PSA >20 ng/ml and/or Gleason score ≥8 and/or cT2c) from a prospective cohort who underwent radical prostatectomy with magnetometer-guided sLND and ePLND. The diagnostic accuracy of sLND was assessed using ePLND as a reference standard. Lymph node metastases were found in 61 of 104 patients (58.7%). sLND had a 100% diagnostic rate, 96.6% sensitivity, 95.6% specificity, 96.6% positive predictive value, 95.6% negative predictive value, 3.4% false negative rate, and 4.4% false positive rate (detecting lymph node metastases outside the ePLND template). These findings demonstrate the high sensitivity and additional diagnostic value of magnetometer-guided sLND, exceeding that of ePLND through the individualized extension of PLND or the detection of sentinel lymph nodes / lymph node metastases outside the established node template in high-risk PCa.

In this paper the influence of austempering temperature and salt bath agitation on the final microstructure and mechanical properties of the ferritic ductile iron were studied. 17 samples had been subjected to different heat treatment parameters. Different microstructures were recorded upon the completion of the tests. From the obtained micro images, it is obvious that both the austempering temperature and salt bath agitation affect the final microstructure of the austempered ductile iron. Lower austempering temperatures and salt bath agitation produce more ausferrite in the microstructure, hence the harder and tougher phases are present. This was confirmed with hardness and toughness test of the 17 heat-treated samples. Lower austempering temperatures give more ausferrite phase and therefore higher hardness, but hardness decreases with increasing austempering temperatures. Toughness rises with rising austempering temperatures, but drops significantly with temperatures above 395°C because of the final microstructure.

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

Observing air quality from sensors onboard light rail cars in Salt Lake County, Utah began as a pilot study in 2014 and has now evolved into a five-year state-funded program. This metropolitan region suffers from both elevated ozone levels during summer and high PM2.5 events during winter. Pollution episodes result predominantly from local anthropogenic emissions but are also impacted by regional transport of dust, chemical precursors to ozone, and wildfire smoke as well as being exacerbated by the topographical features surrounding the city. Two electric light-rail train cars from the Utah Transit Authority light-rail Transit Express (“TRAX”) system were outfitted with PM2.5 and ozone sensors to measure air quality at high spatial and temporal resolution in this region. Pollutant concentration data underwent quality control procedures to determine whether the train motion affected the readings and how the sensors compared against regulatory sensors. Quality assurance results from data obtained over the past year show that TRAX Observation Project sensors are reliable, which corroborates earlier preliminary validation work. Two case studies from summer 2019 are presented to illustrate the strength of the finely-resolved air quality observations: 1) an elevated ozone event and 2) elevated particulate pollution resulting from 4th of July fireworks. The mobile observations were able to capture spatial gradients as well as pollutant hotspots during both of these episodes. Sensors have been recently added to a third light rail train car, which travels on a north-south oriented rail line along which we were unable to monitor air quality previously. The TRAX Observation Project is currently being used to provide reliable pollutant data for health studies and inform urban planning efforts. Links to real-time data displays and updated information on the quality-controlled data from this study are available at https://atmos.utah.edu/air_quality/trax/.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

It is concerning that Cameroon's urban centers are experiencing an alarming rise in air pollution as a result of urbanization, population growth, industrial activity, and transportation emissions. We examined the causes, health impacts, research methodology, case studies, and government measures to address the urgent issue of air pollution in Cameroon's urban regions. We have emphasized how Cameroon's air pollution levels have significantly increased as a result of causes like population expansion, urbanization, industrial emissions, and automobile exhaust A thorough discussion of the negative health impacts of extended exposure to air pollution is included, with special attention to the sensitivity of the old and young. These effects include respiratory disorders, cardiovascular ailments, and early mortality. We emphasized the pressing need for all-encompassing strategies to address air pollution, such as increased public awareness campaigns, stronger emissions regulations, the development of renewable energy sources, and better waste management. The techniques employed in studies on air pollution, like as epidemiological research and air quality monitoring, are also explained to provide light on the unique health dangers that Cameroonian urban dwellers must contend with. We emphasized in our conclusion the significance of joint efforts by legislators, medical professionals, and the general people to reduce air pollution and protect public health in Cameroon in order to create a cleaner and healthier future. In order to protect public health in the future, it is imperative that Cameroon's air pollution be addressed.

The primary sources of particulate matter are linked to human activity. Certain particulate emissions, particularly those of a finer nature, can significantly impact human health, making them one of the most concerning pollutants. Ultrafine particles (UFP), which have a diameter of less than 100 nm, are of particular concern due to their impact on human health and the difficulty in controlling them. The concentration of ultrafine particles (UFP) in the workplace is a growing concern and is classified as an emerging risk. Workers may be exposed to UFP through inhalation, skin absorption, ingestion, or a combination of these routes. This study aims to determine the levels of UFP exposure among workers in environments with varying direct particle emission patterns. Measurements were conducted to compare the results with the levels recommended by the WHO. The study monitored industrial workplaces with direct particulate matter emissions, such as a carpentry and a bakery, as well as social sector sites without or almost without direct particle emissions, such as a school and a health clinic. One conclusion drawn from this study is that all tasks and occupations are susceptible to high levels of UFP, exceeding WHO recommended values in virtually all monitored environments. Therefore, monitoring and controlling UFP is crucial. Further in-depth studies on this subject are also necessary..

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

DNA extraction for downstream molecular diagnostic applications can be an expensive, time-consuming process. We devised a method to quickly extract genomic DNA from environmental samples based on sodium hydroxide lysis of cells with or without capture by magnetic beads, for subsequent PCR or quantitative PCR. The final DNA extraction method using NaOH is extremely low-cost and can be completed in 10 minutes at room temperature. NaOH extraction was effective for Gram-negative and Gram-positive bacteria in samples from air, soil, sewage, food, laboratory surfaces, and chicken cloacal swabs. The NaOH extraction method was comparable to commercial kits for extraction of DNA from pig fecal samples for 16S amplicon sequencing analyses. We demonstrate that an impinger and portable pump can efficiently capture bacteria in poultry facilities for rapid DNA extraction for quantification of total bacteria and for detection of specific species using qPCR. The air sampling and NaOH extraction procedures are well-suited for routine, high throughput screening, and for metagenomic analyses for specific pathogens, even in resource-limited situations.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.

This research investigates the compatibility of conventional air conditioning with the principles of green building, highlighting the need for systems that enhance indoor comfort while aligning with environmental sustainability. Conventional cooling systems, though proficient in regulating indoor temperatures, encounter several issues when incorporated into green buildings. These include energy waste, high running costs, and a misalignment with eco-friendly practices, which may also lead to detrimental environmental effects and potentially reduce occupant comfort, particularly in retrofit situations. Given the emphasis on sustainability and energy conservation in green buildings, there is a pressing demand for heating, ventilation, and air conditioning (HVAC) solutions that support these goals. This study emphasizes the critical need to reconsider traditional HVAC strategies in the face of green building advances. It advocates for the adoption of innovative HVAC technologies designed for eco-efficiency and enhanced comfort. These technologies should integrate seamlessly with sustainable construction, use greener refrigerants, and uphold environmental integrity, driving progress towards a sustainable and occupant-friendly built environment.

A study was conducted on the power system of a forklift equipped with PEM fuel cells. A fuel cell assembly relies on several components for proper functioning, and among these, the air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, we delved into the impact of varying the stoichiometric ratio of air and air pressure on the validated and optimized power module model. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor, being a pivotal component of a PEM fuel cell system, can be oper-ated at different excess air and pressure ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of polymer electrolyte membrane (PEM) fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were con-ducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications.

In Bangkok, the capital city of Thailand, air pollution is a significant problem, and efforts are needed to define organisms that may be used as bioindicators of air pollution. Epiphytic subaerial algae, which grow on the surface of trees, may have a potential as bioindicators of urban air quality. Algae were collected from randomly selected tree trunks in five parks in Bangkok, and the air pollutants CO, NO2, O3, SO2, PM2.5, and PM10 were measured. Analysis of the subaerial algal communities was performed by metagenomics. Diversity indexes were determined for the algal taxa detected, which were separated into groups corresponding to different collection sites by cluster analysis. Relationships between taxa and air pollutants were analyzed by PCA and the Pearson correlation coefficient (r). The results showed a high diversity of epiphytic subaerial al-gae. We recorded 101 taxa belonging to the Cyanophyta (70 taxa), Chlorophyta (21 taxa), Char-ophyta (5 taxa), Bacillariophyta (3 taxa), and Eustigmatophyta (2 taxa). The most abundant taxon was Chroococcidiopsis sp. 1, for which up to 13,254 individuals/cm2 were recorded. The Shan-non–Weaver index ranged between 1.37 and 2.51, the Margalef index between 3.84 and 4.75, and the Pielou index between 0.30 and 0.54. The similarity index was between 8.00% and 64.82% ac-cording to the cluster analysis results for three groups. The PCA indicated that all air pollutants affected the diversity and abundance of the epiphytic subaerial algae. Cyanothece sp. 2 is consid-ered a potential bioindicator of air pollution. It was negatively related to O3 and positively related to NO2 and CO

Numerical simulations and experiments on evaporative condensers in air conditioning systems using R744 were performed. Two configurations were given to study the feasibility of operating the subcritical R744 cycle. It indicated the capable of evaporative cooling condensing R744 to liquify by analyzing the outlet temperature at the end of the condenser reached from 28.7oC to 30.3oC with the operating pressure from 72.6 bar to 68.5 bar. The mass flow rate in the study increases from 14.34 kg/h to 46.08 kg/h, the pressure drop also increases from 0.23 bar to 0.47 bar for the simulation and 0.4 bar to 0.5 bar for the experiment, respectively. This study indicates that a 5-layers of copper tubes configuration causes a higher pressure drop and lower COP when compared to an 8-layers of copper tubes that split into 2 sets for smaller pressure drop. In this study, the evaporative condensers using mini tubes that are flooded in the cooling water tank are suitable for the subcritical R744 air conditioning system. The results obtained from the experimental data are in good agreement with those obtained from the numerical results, with the deviation less than 5%.

During the second half of August 2022, a dust intrusion event occurred, when dust that originated from the dry regions of Kalmyk steppe and the Precaspian plain was transported over the eastern region of Romania. The dry soil in these regions was the result of the severe drought over a long period of time, accentuated by early heat waves in May and June 2022. The dust event was captured by MODIS images. Smoke trains originating from fires in the north of the Azov were also detected, but these did not reach Romania. Optical parametres from AERONET was used to confirm the dust event. To determine the trajectory of the particles, the Hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model was used in this paper. The Ensemble median model was used to highlight the presence and concentration of dust in eastern part of Romania. Aerosols were detected between 0 and 4 km, according to radar and ceilometer data of the REXDAN cloud remote sensing facility in Galați, Romania. This dust intrusion event was the result of the dominant easterly cir-culation caused by the extension of East European High to the northeast of the continent, which transported the dust towards eastern part of Romania for more than 2 days. Moreover, the tor-rential rains between August 22nd and 24th did not clear the atmosphere of dust, since the intense easterly circulation kept carrying the dust into the Moldavian area.