The present study focuses on the synthesis, characterization, and investigation of a p-n heterojunction photocatalysis. Titanium dioxide (TiO2) can’t alone induce the photocatalytic water splitting due to its wide bandgap, which decreases its catalytic activity in the visible light. To make redshift of absorptivity for the TiO2, Nickel (Ni)-doped Graphene (rGO) supported TiO2 was synthesized. Several characterization techniques have been employed to validate the composition and the light absorption ability of the prepared photocatalysts including TEM, SEM, EDS, XRD, XPS, and UV-Vis spectroscopy. The characterization revealed successful doping of the Ni and TiO2 on the rGO nanosheet. Moreover, the UV-Vis spectroscopy indicated a significant shift of light absorption toward the visible spectrum. The photon-induced evolution of H2 was remarkably enhanced using the prepared Ni-rGO/TiO2 nanocomposite. Furthermore, the optimum ratio of rGO: TiO2: Ni in the hybrids was 10:1:4, while the higher Ni ratio would decrease the photocatalytic activity. The stability of the photocatalyst was also verified during 8 cycles of photocatalytic reactions. The kinetic study revealed the nature of the integrated reaction and the controlling step governing the reaction sequence. .

In the present work freezing and melting characteristics of water seeded with chemically functionalized graphene nano-platelets in a vertical cylindrical capsule was experimentally studied. The volume percentage of functionalized graphene nano-platelets was varied from 0.1% to 0.5% with an interval of 0.1%. The stability of the synthesised samples were carried out by zeta potential distribution. The thermal conductivity of the nanocomposite samples were experimentally measured using transient hot wire method. A maximum enhancement of ~24% in the thermal conductivity was observed for the 0.5% volume percentage in the liquid state while a ~53% enhancement in the solid state. Freezing and melting behaviour of water dispersed with graphene nanoplatelets were carried out using a cylindrical stainless steel capsule in a constant temperature bath. The bath temperatures considered for studying freezing characteristics were considered to be −6 °C and −10 °C, while to study the melting characteristics the bath temperature was set as 31 °C and 36 °C. The freezing and melting time decreased for all the test conditions when the volume percentage of GnP increased. The freezing rate was enhanced by ~ 43% and ~32% for the bath temperatures of −6 °C and −10 °C respectively at 0.5 vol % of graphene loading. The melting rate was enhanced by ~42% and ~63% for the bath temperature of 31 °C and 36 °C respectively at 0.5 vol % of graphene loading.

Graphene-based nanomaterials (GNMs), including graphene, graphene oxide, reduced graphene oxide, and graphene quantum dots, may have direct anticancer activity or be used as nanocarri-ers for antitumor drugs. GNMs usually enter tumor cells by endocytosis and can accumulate in lysosomes. This accumulation prevents drugs bound to GNMs from reaching their targets, sup-pressing their anticancer effects. A number of chemical modifications are made to GNMs to facili-tate the separation of anticancer drugs from GNMs at low lysosomal pH and to enable lysosomal escape of drugs. Lysosomal escape may be associated with oxidative stress, permeabilization of the unstable membrane of cancer cell lysosomes, release of lysosomal enzymes into the cytoplasm, and cell death. GNMs can prevent or stimulate tumor cell death by inducing protective autopha-gy or suppressing autolysosomal degradation, respectively. Furthermore, because GNMs prevent bound fluorescent agents from emitting light, their separation in lysosomes may enable tumor cell identification and therapy monitoring. In this review, we explain how the characteristics of the lysosomal microenvironment and the unique features of tumor cell lysosomes can be exploited for GNM-based cancer therapy.

Flow experience, characterized by deep immersion and complete engagement in a task, is highly recognized for its positive psychological impacts. However, previous studies have been restricted to use a single type of task, and the exploration on its neural correlates has been limited. This study aimed to explore the neural correlates of flow experience with the employment of multifac-eted flow-induction tasks. Six tasks spanning mindfulness, artistic tasks, free recall, and varying levels of Tetris complexity (easy, flow, and hard conditions) were employed to have a relatively complete coverage of the known flow-induction tasks for a better induction of individualized flow experience. Twenty-eight participants were recruited to perform these six tasks, with a sin-gle-channel prefrontal electroencephalography (EEG) recording. Significant positive correlations were observed between the subjective flow scores of individual’s best-flow-experience task and the EEG activities at delta, gamma, and theta bands, peaking at latencies around 2 minutes after task onset. The outcomes of our multiple regression analysis yield a maximum coefficient of de-termination (R²) of 0.279. Our findings report the EEG correlates of flow experience in naturalistic settings and highlight the potential of portable and unobtrusive EEG technology for an objective measurement of flow experience.

Breast cancer is a complex and heterogeneous disease that displays diverse molecular subtypes and clinical outcomes. Although it is known that the location of tumors can affect their biological behavior, the underlying mechanisms are not fully understood. In our previous study, we found a differential methylation profile and membrane potential between left (L) and right (R)-sided breast tumors. In this current study, we aimed to identify the ion channels responsible for this phenomenon and determine any associated phenotypic features. To achieve this, experiments were conducted in mammary tumors in mice, human patient samples, and with data from public datasets. The results revealed that L-sided tumors have a more depolarized state than R-ones. We identified a 6-ion channel-gene signature (CACNA1C, CACNA2D2, CACNB2, KCNJ11, SCN3A, and SCN3B) associated with side: L-tumors exhibit lower expression levels than R-ones. Additionally, in silico analyses show that the signature correlates inversely with DNA methylation writers and with key biological processes involved in cancer progression, such as proliferation and stemness. The signature also correlates inversely with patients’ survival rates. In an in vivo mouse model, we confirmed that KI67 and CD44 markers were increased in L-sided tumors and similar tendency for KI67 was found in patient L-tumors. Overall, this study provides new insights into the potential impact of anatomical location on breast cancer biology and highlights the need for further investigation into possible differential treatment options.

The rhythmical nature of the cardiovascular system constantly generates dynamic mechanical forces. At the center of this system is the heart which must detect these changes and adjust its performance accordingly. Mechano-electric feedback provides a rapid mechanism for detecting even subtle changes in the mechanical environment and transducing these signals into electrical responses which can adjust a variety of cardiac parameters such as heart rate and contractility. However, pathological conditions can disrupt this intricate mechanosensory system and manifest as potentially life-threatening cardiac arrhythmias. Mechanosensitive ion channels are thought to be the main proponents of mechano-electric feedback as they provide a rapid response to mechanical stimulation and can directly affect cardiac electrical activity. Here we demonstrate that the mechanosensitive ion channel Piezo1 is expressed in zebrafish cardiomyocytes. Furthermore, chemically prolonging Piezo1 activation in zebrafish results in cardiac arrhythmias indicating that this ion channel plays an important role in mechano-electric feedback. This also raises the possibility that Piezo1 gain of function mutations could be linked to heritable cardiac arrhythmias such as atrial fibrillation in humans.

After the discovery of Corynebacterium glutamicum from the avian feces contaminated soil, its enigmatic L-glutamate secretion by corynebacterial MscCG-type mechanosensitive channels has been utilized for the industrial monosodium glutamate production. Bacterial mechanosensitive channels are activated directly by increased membrane tension upon hypoosmotic downshock, thus the physiological significance of the corynebacterial L-glutamate secretion has been considered as adjusting turgor pressure by releasing cytoplasmic solutes. In this review, we present information that corynebacterial mechanosensitive channels have been evolutionally specialized as carriers to secrete L-glutamate into the surrounding environment in their habitats rather than osmotic safety valves. The lipid modulation activation of MscCG channels in L-glutamate production can be explained by the “Force-From-Lipids” and “Force-From-Tethers” mechanosensing paradigms and differs significantly from the mechanical activation upon hypoosmotic shock. The review also provides information on the search for possibilities that Corynebacterium glutamicum was originally a gut bacterium in the avian host in the aim of understanding physiological roles of corynebacterial mechanosensing. Corynebacterium glutamicum is able to secrete L-glutamate by mechanosensitive channels in the gut microbiota and help the host brain function via the microbiota-gut-brain axis.

The use of large-scale antenna arrays grants considerable benefits in energy and spectral efficiency to wireless systems due to spatial resolution and array gain techniques. By assuming a dominant line-of-sight environment in a massive MIMO scenario with favorable propagation, we derive analytical expressions for the sum-capacity. % Then, we show that convenient simplifications on the sum-capacity expressions are possible when working at low and high SNR regimes. % Furthermore, in the case of a high SNR regime, it is demonstrated that the Gamma PDF can approximate the PDF of the instantaneous channel sum-capacity as the number of BS antennas grows. A second important demonstration presented in this work is that a Gamma PDF can also be used to approximate the PDF of the summation of the channel's singular values as the number of devices increases. Finally, it is important to highlight that the presented framework is useful for LPWAN's as we show that the transmit power of each device can be made inversely proportional to the number of BS antennas.

Network Simulators (NS) is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. This is the case of Mobile Ad hoc Networks (MANETs) which can be extensively used in emergency situations or to gather information without infraestructure. An important factor to get realiable results in the MANETs’ simulations is the wireless channel module of NSs. In this report, we explain how thw wireless channel is implemented in NS-3 and it can be configured.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Currently available DNA detection techniques frequently require compromises between simplicity, speed, accuracy, and cost. Here, we propose a simple, label-free and cost-effective DNA detection platform developed at screen printed carbon electrodes (SPCEs) modified with reduced graphene oxide (RGO) and gold nanoparticles (AuNPs). The preparation of the detection platform involved a two-step electrochemical procedure based on GO reduction onto SPCEs followed by the electrochemical reduction of HAuCl4 to facilitate the post-grafting reaction with AuNPs. The final sensor was fabricated by the simple physical adsorption of a single-stranded DNA (ssDNA) probe onto AuNPs-RGO/SPCE electrode. Each preparation step was confirmed by morphological and structural characterization using scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy, respectively. Furthermore, the electrochemical properties of the modified electrodes have been investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results demonstrated that the introduction of AuNPs onto RGO/SPCEs led to an enhancement in surface conductivity, characteristic that favored an increased sensitivity in detection. The detection process relied on the change in the electrochemical signal induced by the binding of target DNA to the bioreceptor, and was monitored particularly by the change in the charge transfer resistance of a [Fe(CN)6]4−/3− redox couple added in the test solution.

To improve the wear resistance of polyimide (PI), surface modification was developed. In this study, the tribological properties of graphene (GN), graphene oxide (GO), and KH550-grafted graphene oxide (K5-GO) modified PI were evaluated by molecular dynamics (MD) at the atomic level. The findings indicated that the addition of nanomaterials can significantly enhance the friction performance of PI. The friction coefficient of PI composites decreased from 0.253 to 0.232, 0.136, and 0.079 after coating GN, GO and K5-GO, respectively. Among them, the K5-GO/PI exhibited the best surface wear resistance. Importantly, the mechanism behind the modification of PI was thoroughly revealed by observing the wear state, analyzing the changes of interfacial interactions, interfacial temperature, and relative concentration.

Although the dry ice method used to synthesize exfoliated graphite/graphene is little known and used, it has significant advantages over others: it is low cost, simple, and a large quantity of material can be obtained using some inorganic and highly available acids (which can be reused). Despite the above advantages, the main reason for its incipient development is the resulting presence of magnesium oxide in the final product. In the present work, three different treat-ments were tested to remove this remnant using some acid chemical leaching processes, making use of hydrochloric acid, aqua regia, and piranha solution. Based on the experimental evidence, it was found that using aqua regia and combining the leaching process with mechanical milling was the most efficient way of removing such a remnant, the residue being only 0.9 wt.%. This value is low when compared to that obtained with the other acid leaching solutions and purifi-cation process (2.8 - 29.6 wt.%). A mandatory high-energy mechanical milling stage was neces-sary during this treatment, in order to expose and dissolve the highly insoluble oxide without secondary chemical reactions on the graphenes. High-energy mechanical milling is an effective route to exfoliate graphite/graphene, which allows the magnesium oxide to be more susceptible to acid treatment. The obtained surface area was 504 m2g-1; this high value resulting from the in-tense exfoliation can potentiate the use of this material for a wide variety of applications.

The results of the bibliographic analysis show that the most explored nanomaterials in dentistry are graphene and carbon nanotubes, and their derivatives. A detailed analysis and a comparative study on their applications show that, although they are quite similar, graphene based materials seem to be more promising for most of the applications of interest in dentistry. The bibliographic study also demonstrated the potential of zeolite based materials, although the low number of studies on their applications shows that they have not been totally explored, as well as other porous nanomaterials that found important applications in medicine, such as metal organic frameworks, have not been explored. Subsequently, it is expected that the research effort will concentrate in graphene and zeolite based materials in the incoming years. Thus, present review paper presents a detailed bibliographic study, with more than 200 references, in order to describe briefly the main achievements that have been described in dentistry using nanomaterials, compare and analyze them in a critical way, with the aim of predicting the future challenges.

The compatibility of graphene or graphene oxide with its dispersion medium (polymer) plays a critical role in the formation nanocomposite materials with significant property improvements. Environmentally friendly miniemulsion polymerization, which allows a formation of nanoencapsulation in an aqueous phase and high molecular weight polymer/composite production is one promising method. In this study, we screened a series of amphiphilic modifiers and found that the quaternary ammonium (ar-vinyl benzyl) trimethyl ammonium chloride (VBTAC) pending carbon double bonds could effectively modify the graphene oxide (GO) to be compatible with the organophilic monomer. After that, free radical miniemulsion polymerization could successfully synthesize stable latex of exfoliated poly (methyl methacrylate) (PMMA)/ GO nanocomposite. The final latex had an extended storage life and a relatively uniform particle size distribution. X-ray powder diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) analysis of this latex and its films indicated successful encapsulation of exfoliated nano-dimensional graphene oxide inside a polymer matrix.

The cellulose/GO networks as the scaffold of free-standing aerogel electrodes are developed by using lithium bromide aqueous solution as the solvent to ensure the complete dissolution of cotton linter pulp and well dispersion/reduction of GO nanosheets. PANI nanoclusters are then coated onto cellulose/GO networks via in-situ polymerization of aniline monomers. By optimized weight ratio of GO and PANI, the ternary cellulose/GO3.5/PANI aerogel film exhibits well-defined three-dimensional porous structures and high conductivity of 1.15 S/cm that contributes to its high areal specific capacitance of 1218 mF/cm2 at the current density of 1.0 mA/cm2. Utilizing this cellulose/GO3.5/PANI aerogel film as electrodes in a symmetric configuration supercapacitor can result in an outstanding energy density as high as 258.2 μWh/cm2 at a power density of 1201.4 μW/cm2. Moreover, the device can maintain nearly constant capacitance under different bending deformations, suggesting its promising applications in flexible electronics.

Many wounds are unresponsive to current available treatment techniques and therefore there is an immense need to explore suitable materials including biomaterials, which are being considered as the crucial factor to accelerate the healing cascade. In this study, we fabricated polyhydroxyalkanoate based antibacterial mats via electrospun technique. One-pot green synthesized graphene decorated silver nanoparticles (GAg) were incorporated into the fibres of poly-3 hydroxybutarate-co-12 mol% hydroxyhexanoate (P3HB-co-12mol% HHx), a co-polymer of polyhydroxyalkanoate (PHA) family which is highly biocompatible, biodegradable and flexible in nature. The synthesised PHA/GAg biomaterial was characterized by field emission scanning electron microscopy (FESEM), elemental mapping, thermogravimetric analysis (TGA), UV-visible spectroscopy (UV-vis) and Fourier transform infrared spectroscopy (FTIR). In-vitro antibacterial analysis were performed to investigate the efficacy of PHA/GAg against gram positive Staphylococcus aureus (S.aureus) strain 12600 ATCC and gram negative Escherichia coli (E.coli) strain 8739 ATCC. The results indicated that the PHA/GAg demonstrated significant reduction of Staphylococcus aureus (S.aureus strain 12600 ATCC) and Escherichia coli (E.coli strain 8739 ATCC) as compared to bare PHA or PHA-rGO in 2 hours of time. The P value (P< 0.05) was obtained by using 2 sample T-test distribution.

Three-dimensional graphene (3DG) sponge has attracted increasing attention because it combines the unique properties of cellular materials and the excellent performance of graphene. The preparation of 3DG sponge depends mainly on the self-assembly of graphene oxide sheets. Here, we demonstrate facile fabrication of 3DG sponge with a large-scale and ordered porous structure, exploiting the liquid crystals of large graphene oxide (LGO) and ultralarge graphene oxide (ULGO) sheets. The resulting materials exhibit a low density, high porosity and elasticity. Our work explores a new strategy for organizing the ordered alignment of controlled large GO sheets and exploring the relationship between the microstructures and mechanical properties of 3DG sponge.

A novel catechol (CA) biosensor was developed by the immobilization of tyrosinase (Tyr) onto in situ electrochemical reduction graphene (EGR) on choline functionalized gold nanoparticals (AuNPs–Ch) film. The results of UV–visible spectra indicated that Tyr retained its original structure in the film. And electrochemical investigation of the biosensor showed a pair of well–defined, quasi–reversible redox peaks with E_pa= –0.0744V and E_pc= –0.114 V (vs. SCE) in 0.1 M, pH 7.0 sodium phosphate buffered saline at the scan rate of 100 mV/s. The transfer rate constant k_s was 0.66 s^–1. The Tyr–EGR/AuNPs–Ch showed a good electrochemical catalytic response for the reduction of CA, with the linear range from 0.2 to 270 μM and a detection limit of 0.1 μM (S/N= 3). The apparent Michaelis–Menten constant was estimated to be 109 μM.

We present a series of computer-assisted high resolution transmission electron (HRTEM) simulations to determine Moiré patters by induced twisting effects between slabs at rotational angles of 3°, 5°, 8°, and 16°, for molybdenum disulfide, graphene, tungsten disulfide, and tungsten selenide layered materials. In order to investigate the electronic structure, a series of numerical simulations using DFT methods was completed using CASTEP with a generalized gradient approximation to determine both band structure and density of states on honeycomb like new superlattices. Our results indicate metallic transitions when rotation approaches 8° with respect to each other for most of the two-dimensional systems that were analyzed.

Vertical graphene nanowalls (VGNWs) have emerged as a highly promising material in recent years due to their exceptional properties, such as a high specific surface area, excellent electrical conductivity, scalability, and compatibility with transition metal compounds. These attributes make VGNWs a compelling candidate for various applications, including energy storage, catalysis, and sensing, fostering great interest in their use in next future commercial graphene-based sensors like optoelectronic and plasmonic devices, energy storage electrodes, and catalytic systems. Among the diverse graphene synthesis methods, plasma-enhanced chemical vapor deposition (PECVD) has proven to be a robust technique for producing large-scale graphene films and creating VGNWs on diverse substrates. However, despite substantial progress in optimizing growth conditions to achieve micrometer-sized graphene nanowalls, the outcomes are often obtained through empirical approaches, and a comprehensive understanding of the underlying physicochemical mechanisms governing nanostructure formation remains elusive. In particular, a deeper exploration of atomic-level phenomena, such as nucleation, carbon precursor adsorption, and surface diffusion of adatoms, is imperative to exert precise control over the growth process. Concerning the synthesis of VGNWs, hydrogen plays a dual role in the graphene growth process, acting as both a co-catalyst and an etchant for the nanowalls. Nevertheless, a thorough comprehension of the intricate growth process is still required. To address these knowledge gaps, this review paper aims to investigate the nucleation and growth of VGNWs using PECVD, with a specific focus on exploring the temperature effect on the graphene growth ratio and nucleation density across a wide range of temperatures. By providing valuable insights into the PECVD process, our objective is to enable the optimization of growth conditions for tailoring VGNWs' properties, thereby facilitating their application in energy storage, catalysis, and sensing fields.

Abstract: NFinFET transistors with fin channel length 90nm and a planar MOSFET transistor with channel length 180nm and 90nm are presented with characteristic curves at various gate biases. A finalized algorithm with kink effects is effectively responsible for addressing the field effect transistors. The algorithm includes the modified conventional current-voltage formula and a nonlinear heat-associated kink solution which is simplified as a Gaussian form. Three parameters in modified model includes kN (related with channel width, channel length, and gate oxide capacitor, and proportional to the mobility of carriers)Vth(Threshold Voltage), and (the inverse of Early Voltage). Those parameters are determined to minimize the discrepancies between the measured data and the fitting values, but leave kinks located at around (VGS－Vth), which are deliberately eliminated by the Gaussian form because of the agitation of thermal kink effects. The whole fitting is made to be as close as the as-measured IDS-VDS. In the mean time, those determined parameters are physically meaningful after the analysis has been done.

Single image deraining (SID) has shown its importance in many advanced computer vision tasks. Though many CNN based image deraining methods have been proposed, how to effectively remove raindrops while maintaining background structure remains a challenge that needs to be overcome. Most of the deraining work focuses on removing rain streaks, but in heavy rain images, the dense accumulation of rainwater or the rain curtain effect significantly interferes with the effective removal of rain streaks, and often introduces some artifacts that make the scene more blurry. In this paper, we propose a new network structure R-PReNet for single image deraining with good background structure maintaining. This framework fully utilizes the cyclic recursive structure of PReNet. Moreover, we introduce residual channel prior (RCP) and feature fusion modules for better deraining performance by focusing on background feature information. Compared with the previous methods, our method has significantly improvement effect on the rainstorm image with the artifacts removing and good visual detail restoring.

The protein TRPM8, a non-selective, calcium (Ca2+) permeable ion channel is implicated in several pathological conditions, including neuropathic pain states. In our previous research endeavors, we have identified β–lactam derivatives with high hydrophobic character that exhibit potent and selective TRPM8 antagonist activity. This work describes the synthesis of novel derivatives featuring C-terminal amides and diversely substituted N’-terminal monobenzyl groups, in an attempt to increase the total polar surface area (TPSA) in this family of compounds. The primary goal was to assess the influence of these substituents on the inhibition of menthol-induced cellular Ca2+ entry, thereby establishing critical structure-activity relationships. While the substitution of the tert-butyl ester by isobutyl amide moieties improved the antagonist activity, none of the N’-monobencyl derivatives, regardless of the substituent on the phenyl ring, achieved the activity of the model dibenzyl compound. The antagonist potency of the most effective compounds was subsequently verified using Patch-Clamp electrophysiology experiments. Furthermore, we evaluated the selectivity of one of these compounds against other members of the TRP ion channel family and some receptors connected to peripheral pain pathways. This compound demonstrated specificity for TRPM8 channels. To better comprehend the potential mode of interaction, we conducted docking experiments to uncover plausible binding sites on the functionally active tetrameric protein, which come upon four main poses by the pore zone, differents from those described for other known antagonists. Finally, in vivo experiments, involving a couple of selected compounds, revealed significant antinociceptive activity within a mice model of cold allodynia induced by oxaliplatin.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

In the field of vision-based robot grasping, effectively leveraging RGB and depth information to accurately determine the position and pose of a target is a critical issue. To address this challenge, we propose a tri-stream cross-modal fusion architecture for 2-DoF visual grasp detection. This architecture facilitates the interaction of RGB and depth bilateral information and is designed to efficiently aggregate multiscale information. Our novel modal interaction module (MIM) with spatial-wise cross-attention algorithm adaptively captures cross-modal feature information. Meanwhile, the channel interaction modules (CIM) further enhance the aggregation of different modal streams. In addition, we efficiently aggregate global multiscale information through a hierarchical structure with skipping connections. To evaluate the performance of our proposed method, we conduct validation experiments on standard public datasets and real robot grasping experiments. We achieve the image-wise detection accuracy of 99.4% and 96.7% on Cornell and Jacquard datasets respectively. The object-wise detection accuracy reaches 97.8% and 94.6% on the same datasets. Furthermore, physical experiments using the 6-DoF Elite robot demonstrate a success rate of 94.5%. These experiments highlight the superior accuracy of our proposed method.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton com-munities but different detection approaches are biased uniquely. Genetic identification of marine plankton has become standard but is still not used in routine monitoring. This study assessed the diversity of plankton taxa using 18S high throughput sequencing from 2011-2012 from small-volume (~200ml) samples from the Water and Microplankton Sampler (WaMS) deployed on the Continuous Plankton Recorder platform (CPR). The 18S-HTS survey revealed a bias towards heterotrophic taxa, and phototrophs under 10µm within the photosynthetic community. In comparison with phytoplankton microscopic counts from the CPR survey and Western Channel Observatory station L4, only 8-12 taxonomic families were common to all three surveys, with a bias towards larger diatoms and dinoflagellate taxa in microscopy surveys. The WaMS survey detected a contrasting but complementary taxa set to that of microscopic surveys. Additional Quantitative PCR was carried out on the picoeukaryotic pelagophyte, Aureococcus anophagefferens, and the nanoeukaryotic potential harmful algae, Pseudo-nitzschia delicatissima, from 2011-2013. This confirmed the persistence presence of A. anophagefferens in the Western Channel and an elevated abundance of both species in 2011. Species specific seasonality were distinct from those of aggregrate phytoplankton groups.

Land cover mapping provides spatial information on the physical properties of the Earth’s surface, for various classes of wetlands, artificial surface and constructions, vineyards, water bodies, etc. Having reliable information on land cover is crucial to developing solutions to a variety of environmental problems such as destruction of important wetlands/forests, and loss of fish and wildlife habitats. This has made land cover mapping one of the most widespread application areas in remote sensing computational imaging. However, due to the differences between modalities in terms of resolutions, content, and sensors, integrating complementary information that multi-modal remote sensing imagery exhibits into a robust and accurate system still remains challenging, and classical segmentation approaches generally do not give satisfactory results for land cover mapping. In this paper, we propose a novel dynamic deep network architecture, AMM-FuseNet, that promotes the use of multi-modal remote sensing images for the purpose of land cover mapping. The proposed network exploits the hybrid approach of the Channel Attention mechanism and Densely Connected Atrous Spatial Pyramid Pooling (DenseASPP). In the experimental analysis, in order to to verify the validity of the proposed method, we test AMM-FuseNet applied to four datasets whilst comparing it to the 6 state-of-the-art models of DeepLabV3+, PSPNet, UNet, SegNet, DenseASPP, and DANet. In addition, we also demonstrate the capability of AMM-FuseNet under minimal training supervision (reduced number of training samples) compared to the state-of-the-art, achieving less accuracy loss even for the case with 1/20 of the training samples.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton communities but is biased towards those organisms that can be distinguished using the microscope. Genetic identification of marine plankton has become standard but is still not used. This study is a comprehensive study genetically measured taxa in the Western Channel of UK using a small-volume automated water sampler deployed on the CPR platform. The study present one year of high-throughput sequencing data focussing on smaller plankton and separate community to that measured by microscopy that can complement each other for a holistic view of plankton. Quantitative tests of two harmful algae show relatively high abundance of the Pelagophyte Aureococcus anophagefferens during 2011 with low nitrite levels. Three years of Pseudo-nitzschia delicatissima quantitative monitoring also shows a greater abundance of this potentially harmful taxa in 2011. Flow cytometry reveals distinct seasonal cycles with distinct timings.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

One of the most important subjects of hydraulic engineering is the reliable estimation of the transverse distribution in rectangular channel of bed and wall shear stresses. This study makes use of the Tsallis entropy, Genetic Programming (GP) and (ANFIS) methods to assess the shear stress distribution (SSD) in rectangular channel. To evaluate the results of the Tsallis entropy, GP and ANFIS models, laboratory observations were used in which shear stress was measured using an optimized Preston tube. This is then used to measure the SSD in various aspect ratios in the rectangular channel. To investigate the shear stress percentage, 10 data series with a total of 112 different data for were used. The results of the sensitivity analysis show that the most influential parameter for the SSD in smooth rectangular channel is the dimensionless parameter B/H, Where the transverse co-ordinate is B, and the flow depth is H. With the parameters (b/B), (B/H) for the bed and (z/H), (B/H) for the wall as inputs, the modeling of the GP was better than the other one. Based on the analysis, it can be concluded that the use of GP and ANFIS algorithms is more effective in estimating shear stress in smooth rectangular channels than the Tsallis entropy-based equations.

Voltage-gated Ca²⁺ (Ca_v) channels play pivotal roles in regulating gene transcription, neuronal excitability, and neurotransmitter release. In order to meet the spatial and temporal demands of visual signaling, Ca_v channels exhibit unusual properties in the retina compared to their counterparts in other areas of the nervous system. Here, we review current concepts regarding the specific subtypes of Ca_v channels expressed in the retina, their intrinsic properties and forms of modulation, and how their dysregulation could lead to retinal disease.

Transient receptor potential canonical (TRPC) channels are ubiquitously expressed in excitable and non-excitable cardiac cells where they sense and respond to a wide variety of physical and chemical stimuli. As other TRP, TRPC may form homo or heterotetrameric ion channel, and they can associate with other membrane receptors and ion channels to regulate intracellular calcium concentration. Dysfunctions of TRPC channels are involved in many types of cardiovascular diseases. Significant increase of the expression of different TRPC isoforms has been observed in different animal model of heart infarcts, and in vitro experimental model of ischemia and reperfusion. TRPC-mediated increase of the intracellular Ca²⁺ concentration seems required for the activation of signaling pathway that plays minor roles in the healthy heart, but they are more relevant for cardiac responses to ischemia, such as the activation of different factors of transcription and cardiac hypertrophy, fibrosis, and angiogenesis. In this review, we will highlight the current knowledge regarding TRPC implication in different cellular processes related to ischemia and reperfusion, and to heart infarction.

Accurate channel estimation is of utmost importance for massive MIMO systems that allow providing significant improvements in spectral and energy efficiency. In this work, we investigate the spectral efficiency performance and present a channel estimator for multi-cell massive MIMO systems subjected to pilot-contamination. The proposed channel estimator performs well under moderate to aggressive pilot contamination scenarios without prior knowledge of the inter-cell large-scale channel coefficients and noise power. The estimator approximates the performance of a linear Minimum Mean Square Error (MMSE) as the number of antennas increases. Following, we derive a lower bound closed-form spectral efficiency of the Maximum Ratio Combining (MRC) detector in the proposed channel estimator. The simulation results highlight that the proposed estimator performance approaches the linear minimum mean square error (LMMSE) channel estimator asymptotically.

Accurate channel estimation is of utmost importance for massive MIMO systems to provide significant improvements in spectral and energy efficiency. In this work, we present a study on the distribution of a simple but yet effective and practical channel estimator for multi-cell massive MIMO systems suffering from pilot-contamination. The proposed channel estimator performs well under moderate to aggressive pilot contamination scenarios without previous knowledge of the inter-cell large-scale channel coefficients and noise power, asymptotically approximating the performance of the linear MMSE estimator as the number of antennas increases. We prove that the distribution of the proposed channel estimator can be accurately approximated by the circularly-symmetric complex normal distribution, when the number of antennas, M, deployed at the base station is greater than 10.

Subcellular targeting of opsins in optogenetics provides new possibilities for investigating the function of nerve cells. One of the widely used motifs for central targeting of opsins is the motif of potential-dependent potassium channel Kv2.1. We have expressed construct CHR2-Venus-Kv2.1 in the layer 2/3 pyramidal neurons of the murine cerebral cortex by means of in utero electroporation. It was found that, although the majority of neurons expressing CHR2-Venus-Kv2.1 demonstrated mainly central localization of fluorescence in the soma, proximal dendrites and axon, there was also significant population of neurons with disruption of the “correct” targeting resulting in the fluorescent protein distributed uniformly throughout the entire cell surface. We have suggested that observed mislocalization was caused by overexpression of the construct. Indeed, a decrease in the plasmid concentration during the in utero electroporation procedure resulted in almost complete absence of neurons with altered targeting. Thus, the possibility of “incorrect” targeting of CHR2 by the potassium channel motif Kv2.1 should be taken into account when using this construct in optogenetic experiments.

A new approach to the measurement with elastic lidar of depolarization produced by atmospheric aerosols is presented. The system uses two different telescopes: one for depolarization measurements and another for total-power measurements. The system architecture and principle of operation are described. The first experimental results are also presented, corresponding to a collection of atmospheric conditions over the city of Barcelona.

For the first time, few-layer graphene (FLG) nanosheets were synthesized by the method of self-propagating high-temperature synthesis (SHS) from biopolymers (starch and lignin). We suggested that biopolymers (lignin, tree bark) and polysaccharides, in particular starch, could be an acceptable source of native cycles for the SHS process. The carbonization of biopolymers under the conditions of the SHS process was chosen as the basic method of synthesis. Chemical reactions, under the conditions of the SHS process, proceed according to a specific mechanism of nonsothermal branched-chain processes, which are characterized by the joint action of two fundamentally different process-accelerating factors - avalanche reproduction of active intermediate particles and self-heating. The method of obtaining FLG nanosheets included the thermal destruction of hydrocarbons in a mixture with an oxidizing agent. We used biopolymers as hydrocarbons and ammonium nitrate as an oxidizing agent. Thermal destruction was carried out in the mode of SHS, heating the mixture in a vessel at a speed of 20–30 oC/min to 150-200 oC and keeping at this temperature for 15–20 min with the discharge of excess gases into atmosphere. A combination of spectrometric research methods, supplemented by electron microscopy data, has shown that the particles of the carbonated product powder in their morphometric and physical parameters correspond to FLG nanosheets. An X-ray diffraction analysis of the indicated FLG nanosheets was carried out, which showed the absence of formations with a graphite crystal structure in the final material. The surface morphology was also studied and the features of the IR absorption of FLG nanosheets were analyzed. It is shown that the developed SHS method makes it possible to obtain FLG nanosheets with linear dimensions of tens of microns and a thickness of not more than 1-5 graphene layers (several graphene layers).

Keywords: Baseband, GeoSurf Constellation, Interference, Linear Distortions, Passband, Time Delay, Rain attenuation, Synthetic Storm Technique, ultra–wideband.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

This study is part of an extended investigation into the quantitative detection of therapeutic molecules with antineoplastic properties, specifically focusing on bleomycin. The objective is to minimize adverse effects while maximizing therapeutic effectiveness. We are presenting the results for bleomycin detection, in terms of cyclic voltammetry and electrochemical impedance spectroscopy. We are continuing an approach we have recently started, of an electrochemical biosensor based on graphene, which is evidenced to be a revolutionary nanomaterial. The vertical graphene biosensor exhibited improved sensitivity, faster response, faster occurrence of the chemical reactions, and higher electrode surface conductivity, than the classical gold IDE sensor. The construction of the electrochemical sensor involved growing vertically aligned graphene nanosheets on the conductive surface of interdigitated electrodes. The results for bleomycin detection emphasized that a simpler surface modification method proved to be more efficient.

The COVID-19 pandemic caused by the virus SARS-CoV-2 has been the greatest global threat to human health in the last three years. The most widely used methodologies for the diagnosis of COVID-19 are quantitative reverse transcription polymerase chain reaction (RT-qPCR), used to detect the viral genome, and rapid antigen tests (RATs), also known as lateral flow tests, that employ specific antibodies to detect the viral spike protein. While PCR is considered the gold standard test in terms of specificity and sensitivity, it is time-consuming and requires specialized instrumentation operated by skilled personnel. In contrast, RATs can be used in-home or at point-of care but are less sensitive leading to a higher rate of false negative results. An alternative methodology for the detection of virus is the use of electrochemical biosensors that employ disposable strip electrodes to which binding of viral components elicits a change in electrical signal. Laser-scribed graphene (LSG) electrodes are attractive candidates for use as biosensors electrodes suitable for SARS-COV-2 detection due to their low-cost, patternability and ease of fabrication. In this work, we describe the development of a biosensor for COVID-19 detection that exploits a split-ester bond ligase system (termed ‘EsterLigase’) for immobilization of a virus-specific nanobody to maintain the out-of-plane orientation of the probe to ensure the efficacy of the probe-target recognition process. An anti-spike VHH E nanobody, genetically fused with the EsterLigase domain, was used as the specific probe for the spike receptor-binding domain (SP-RBD) protein as the target. The recognition between the two was measured by the change in the charge transfer resistance, determined by fitting the electrochemical impedance spectroscopy (EIS) spectra. The developed LSG-based biosensor achieved a linear detection range for the SP-RBD from 15 pM to 150 nM with a sensitivity of 0.0866 [log(M)]-1 and a limit of detection (LOD) of 7.68 pM.

The nanocomposites with reversible cross-linking covalent bonds were prepared by reacting furfurylamine (FA)-modified diglycidyl ether of bisphenol A (DGEBA) and furfuryl-functionalized aniline trimer-modified graphene (TFAT-G) with bismaleimide (BMI) via Diels-Alder (DA) reaction. The successful synthesis of the TFAT modifier is confirmed by NMR hydrogen spectroscopy and IR spectroscopy tests. The structure and properties of TFAT-G epoxy nanocomposites are characterized by SEM, DSC, tensile and resistivity CES. The results show that TFAT-G was uniformly dispersed in the resin, and 1wt% TFAT-G composites increase to 233% for tensile strength, 63% for elongation at break, 66.1% for modulus and 7.8℃ for Tg. Overall, the graphene/self-healing resin nanocomposites have both good self-healing function and electrical conductivity by adding 1% modified graphene and still maintain the original 83% strength and 89% electrical conductivity after one cycle of heating repair.

We used a metal-organic chemical vapor deposition technique to synthesize a boron-doped reduced graphene oxide (B-rGO) material with various electrical characteristics, dependent on simultaneous reduction and doping procedures. The effect of the doping level on the B bonding in the reduced graphene oxide (rGO) layer controlled by the annealing temperature was investigated using X-ray photoelectron spectroscopy (XPS). The XPS data indicated that the B-rGO layer had a higher B concentration and a considerable number of O-B bonds as a result of the appreciable annealing temperature, which resulted in a decreased work function and Schottky contact between B-rGO and n-type Si. Owing to the higher proportion of B-C and B-C3 bonding in the B-rGO device than that in the rGO/Si device, the lower Schottky barrier height of the B-rGO/n-Si vertical junction photodetector resulted in a higher responsivity. This work suggests a facile method of B doping to alter the electrical properties of graphene materials.

In this study, 3D printing of poly-l-lactic acid (PLLA) scaffolds reinforced with graphene oxide (GO) nanoparticles via Digital Light Processing (DLP) was investigated to mimic bone tissue. Stereolithography is one of the most accurate additive manufacturing method, but the dominant available materials used in this method are toxic. In this research, a biocompatible resin (PLLA) was synthetized and functionalized to serve the purpose. Due to the low mechanical properties of the printed product with the neat resin, graphene oxide nanoparticles in three levels (0.5, 1, and 1.5 Wt.%) were added with the aim of enhancing the mechanical properties. At first, the optimum post cure time of the neat resin was investigated. Consequently, all the parts were post-cured for three hours after printing. Due to the temperature-dependent structure of GO, all samples were placed in an oven at 85 ° C for different time periods of 0, 6, 12, and 18 hours to increase mechanical properties. The compression test of heat treated samples reveals that the compressive strength of the printed parts containing 0.5,1, and 1.5 % of GO increased by 151,162 ad 235%, respectively. Scaffolds with the designed pore sizes of 750 microns and a porosity of 40% were printed. Surface hydrophilicity test was performed for all samples showing that the hydrophilicity of the samples increased with increasing GO percentage. The degradation behavior of the samples was evaluated in a PBS environment, and it revealed that by increasing GO, the rate of component degradation increased, but the heat treatment had the opposite effect and decreased the degradation rate. Finally, besides improving biological properties, a significant increase in mechanical properties under compression can introduce the printed scaffolds as a suitable option for bone implants.

This work reports the influence of reduced graphene oxide (rGO) support on the catalytic performance of Cu@PtRu/rGO catalysts towards methanol oxidation in acidic medium. These core-shell catalysts are synthesized by the reduction method in two steps being the first using ethylene glycol to obtain Cu/rGO and the second, the reduction of copper atoms synthesized in the previous step to produce Cu@PtRu/rGO. In order to compare the catalytic performance of the prepared catalysts, Pt/C, PtRu/C, Cu@PtRu/C catalysts are also synthesized on Vulcan XC-72R carbon. The theoretical loading of Pt used in the Vulcan XC-72R carbon supported catalysts is equal to that utilized in Cu@PtRu/rGO, and higher in the other prepared catalysts. The surface composition of the nanoparticles, as well as their sizes, particle size distribution and morphology of the catalyst particles are characterized by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Cyclic voltammetry (CV) and chronoamperometry (CA) are employed to measure the electrochemical performance of the prepared catalysts. The anodic scans show that for the region of technological interest (0.1 to 0.4 V), the Cu@PtRu/rGO-16 electrocatalyst exhibits higher current density value than the others as a result of its lower starting oxidation potential (0.250V against 0.437V for Pt/C) and its higher ratio between forward (iF) and reverse (iR) current densities (iF/iR 1.45 against 0.93 for Pt/C). Chronoamperometric tests depict that the current density value of Cu@PtRu/rGO-16 catalyst is about 4 times higher than that of Cu@PtRu/C-16 and Cu@PtRu/C-18 catalysts, ca. 4.8 times higher than that of PtRu/C-30 catalyst and around 6 times higher than that of Pt/C-30. These results suggest that Cu@PtRu/rGO-16 exhibits high bulk activity for the electrooxidation of methanol, high stability and high tolerance to CO poisoning, making it possible to reduce the platinum loading in proton exchange membrane fuel cells (PEMFCs).

Epinephrine (EP, also called adrenaline) is a compound belonging to the catecholamine neurotransmitter family. It can cause neurodegenerative diseases such as Alzheimer’s disease, Parkinson’s disease, Huntington’s disease and amyotrophic lateral sclerosis. This work describes an amperometric sensor for the electroanalysis of EP, based on an inkjet-printed graphene electrode (IPGE), modified by a thin film of a laponite (La) clay mineral. The ion exchange properties and permeability of the prepared sensor (denoted La/IPGE) were evaluated using multi-sweep cyclic voltammetry while its charge transfer resistance was determined by electrochemical impedance spectroscopy. The results showed globally that La/IPGE exhibited more a sensitive response towards the detection of EP, in comparison with the bare IPGE. The developed sensor was directly applied for the determination of EP in aqueous solution using differential pulse voltammetry, and under optimized conditions, the calibration curve was plotted in the concentration range of 0.8 to 60 μM. The anodic peak current of EP was directly proportional to its concentration, leading to a detection limit of 0.29 μM. The sensor was successfully applied for the determination of EP in pharmaceutical preparation and best recovery rates were also obtained. The interfering effect of selected species was evaluated to highlight the selectivity of the elaborated sensor.

Since the discovery of graphene, due to its excellent optical, thermal, mechanical and electrical properties, it has a broad application prospect in energy, materials, biomedicine, electromagnetism and other fields. A great quantity of researches on the physical mechanism of graphene has been applied to engineering in electromagnetism and optics. To study the properties of graphene, different kinds of numerical methods have been developed for simulating the electromagnetic field effects of graphene, and equivalent boundary conditions have been employed to replace graphene in the computational domain. In this work, the numerical methods with equivalent boundary conditions are reviewed, and some examples are provided to illustrate their applicability.

Graphene is perhaps the most prominent “Dirac material,” a class of systems whose electronic structure gives rise to charge carriers that behave as relativistic fermions. In multilayer graphene several crystal sheets are stacked such that the honeycomb lattice of each layer is displaced along one of the lattice edges. When subject to an external magnetic field, the scaling of the multilayer energy spectrum with the magnetic field, and thus the system’s thermodynamic behavior, depends strongly on the number of layers. With this in mind, we examine the performance of a finite-time endoreversible Otto cycle with multilayer graphene as its working medium. We show that there exists a simple relationship between the engine efficiency and the number of layers, and that the efficiency at maximum power can exceed that of a classical endoreversible Otto cycle.

Cutting-edge technologies are intensifying into new skylines and this remarkable progress has been successfully influenced by the tiny level engineering of carbon dots technology, their syn-thesis advancement and impressive applications in the field of allied sciences. The advances of science and its conjugation with interdisciplinary fields emerged in carbon dots making, their controlled characterization and applications into faster, cheaper as well as more reliable prod-ucts in various scientific domains. Thus, a new era in nanotechnology has developed into carbon dots technology. The understanding of the generation process, control on making processes and selected applications of carbon dots such as energy storage, environmental monitoring, catalysis, contaminates detections and complex environmental forensics, drug delivery, drug targeting and other biomedical applications etc. are among the most promising applications of carbon dots and thus a thrust area of research today. In this regard, various types of carbon dots nano-materials such as oxides, their composites and conjugations etc. have been flocking significant attention due to their remarkable potential in this thrust area of energy, the environment and technology. Thus, the present paper highlights the role and importance of carbon dots, recent advancements in their synthesis methods, properties and emerging applications.

The electromagnetic inference is an issue from decades, where working for a better shielding material is still on-going. The purpose of this study is to review the existing methods in the formation of graphene, metal and polymer-based composites. Study indicates that in graphene and metal-based composites, the utilization of alternating deposition method showed the highest shielding effectiveness, whereas, in polymer-based composite, the utilization of chemical vapor deposition method showed highest shielding effectiveness. However, this review reveals that still there is a gap in the literature in terms of the selection of the method. Although there are various available methods which researchers adopt as per their convenience, none of the studies makes a comparison of the methods to form a similar composite. Therefore, as a future gap researcher needs to adopt various methods to form a single composite and then make a comparison of shielding effectiveness. This act will be useful for future researchers to select the appropriate method.

Few-layer graphene oxide (GO) has shown none or very weak cytotoxicity and anti-proliferative effects in a wide range of cell lines such as glyoma cells and human skin HaCaT cells, in concentrations up to 100 µg/mL However, multi-layer GO has been hardly explored in the biomedical field. Thus, multi-layer GO was examined here in human keratinocyte HaCaT cells treated with different concentrations ranging from 0.01 to 150 µg/mL during different periods of times (3, 12 and 24 hours). The results of this study showed a time-concentration dependence with two non-cytotoxic concentrations (0.01 and 0.05 µg/mL) and a median effective concentration value of 4.087 µg/mL at 24 hours of GO exposure. Contrary to what has been reported for few-layer GO, cell proliferation of the HaCaT cells in contact with the multi-layer GO at 0.01 μg/mL showed identical proliferative activity compared to an epidermal growth factor (1.6-fold greater than the control group) after 96 hours. The effects of the multi-layer GO on the expression of 13 genes (SOD1, CAT, MMP1, TGFB1, GPX1, FN1, HAS2, LAMB1, LUM, CDH1, COL4A1, FBN and VCAN) at the non-cytotoxic concentrations of GO in the HaCaT cells were analyzed after 24 hours. Thus, the lowest non-cytotoxic GO concentration was able to up-regulate the CAT, TGFB1, FN1 and CDH1 genes, which confirms the great potential of multi-layer GO in the biomedical field.

In this work we theoretically investigate the responsivity/noise equivalent power (NEP) trade-off in graphene/semiconductor Schottky photodetectors (PDs) operating in the near-infrared regime and working at room temperature. Our analysis shows as the responsivity/NEP ratio is strongly dependent on the Schottky barrier height (SBH) of the junction and we derive a closed analytical formula for maximizing it. In addition, we theoretically discuss as the SBH is linked to the bias applied to the junction in order to show how these devices could be optimized in practice for different semiconductors. We discover that graphene/n-silicon (Si) Schottky PDs could be optimized at 1550nm showing a responsivity and NEP of 133mA/W and 500fW/Hz, respectively, by a low reverse bias of only 0.66V. Moreover, we show that graphene/n-germanium (Ge) Schottky PDs optimized in term of responsivity/NEP ratio could be employed at 2000nm with a responsivity and NEP of 233mA/W and 31pW/Hz, respectively. We believe that our insights are of great importance in the field of silicon photonics for the realization of Si-based PDs to be employed in power monitoring, lab-on-chip and environment monitoring applications.

The Kerr nonlinear optical performance of silicon nanowire waveguides integrated with 2D layered graphene oxide (GO) films is theoretically studied and optimized based on experimentally measured linear and nonlinear optical parameters of the GO films. The strong mode overlap between the silicon nanowires and highly nonlinear GO films yields a significantly enhanced Kerr nonlinearity for the hybrid waveguides. A detailed analysis for the influence of waveguide geometry and GO film thickness on the propagation loss, nonlinear parameter, and nonlinear figure of merit (FOM) is performed. The results show that the effective nonlinear parameter and nonlinear FOM can be increased by up to ≈52 and ≈79 times relative to bare silicon nanowires, respectively. Self-phase modulation (SPM)-induced spectral broadening of optical pulses is used as a benchmark to evaluate the nonlinear performance, examining the trade-off between enhancing Kerr nonlinearity and minimizing loss. By optimizing the device parameters to balance this, a high spectral broadening factor of 27.6 can be achieved ‒ more than 6 times that achieved in previous experiments. Finally, the influence of pulse chirp, material anisotropy, and the interplay between saturable absorption and SPM is also discussed. These results provide useful guidance for optimizing the Kerr nonlinear optical performance of silicon waveguides integrated with 2D layered GO films.

With superior optical properties, high flexibility in engineering its material properties, and strong capability for large-scale on-chip integration, graphene oxide (GO) is an attractive solution for on-chip integration of two-dimensional (2D) materials to implement functional integrated photonic devices capable of new features. Over the past decade, integrated GO photonics, representing an innovative merging of integrated photonic devices and thin GO films, has experienced significant development, leading to a surge in many applications covering almost every field of optical sciences. This paper reviews the recent advances in this emerging field, providing an overview of the optical properties of GO as well as methods for the on-chip integration of GO. The main achievements made in GO hybrid integrated photonic devices for diverse applications are summarized. The open challenges as well as the potential for future improvement are also discussed.

For some decades, the scientific community has been looking for alternatives to the use of fossil fuels that allow the planet's sustainable and environmentally friendly development. To do this, attempts have been made to mimic some processes that occur in nature, among which the photosystem-II stands out, which allows water splitting operating with different steps to generate oxygen and hydrogen. This research presents promising results using synthetic catalysts, which try to simulate some natural processes, and which are based on Au@ZnO-graphene compounds. These catalysts were prepared by incorporating different amounts of gold nanoparticles (1 wt.%, 3 wt.%, 5 wt.%, 10 wt.%) and graphene (1 wt.%) on the surface of synthesized zinc oxide nanowires (ZnO NWs), and zinc oxide nanoparticles (ZnO NPs), along with a commercial form (commercial ZnO) for comparison purposes. The highest amount of hydrogen (1,127 µmol/hg) was reported by ZnO NWs with a gold and graphene loadings of 10 wt.% and 1 wt.%, respectively, under irradiation at 400 nm. Quantities of 759 µmol / hg and 709 µmol / hg were obtained with catalysts based on ZnO NPs and commercial ZnO, respectively. The photocatalytic activity of all composites increased with respect to the bare semiconductors, being 2.5 times higher in ZnO NWs, 8.8 times for ZnO NPs and 7.5 times for commercial ZnO. The high photocatalytic activity of the catalysts is attributed, mainly, to the synergism between the different amount of gold and graphene incorporated, and the surface area of the composites.

Nanomedicine has allowed for emerging advances in imaging, diagnostics and therapeutics. Regenerative Medicine has taken advantage of a number of nanomaterials for reparation of diseased or damaged tissues in the nervous system involved in memory, cognition and movement. Electrical, thermal, mechanical and biocompatibility aspects of carbon-based nanomaterials (nanotubes, graphene, fullerenes and their derivatives) make them suitable candidates to drive nerve tissue repair and stimulation. This review article focuses on recent advances on the use of carbon nanotube (CNT)-based technologies on nerve tissue engineering; outlining how neurons interact with the nanomaterials interface for promoting neuronal differentiation, growth and network reconstruction for their possible use in therapies of neurodegenerative pathologies and spinal cord injuries.

NiFe alloy nanoparticles/graphene oxide hybrid (NiFe/GO) was prepared for electrochemical glucose sensing. The as-prepared NiFe/GO hybrid was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The results indicated that NiFe alloy nanoparticles can be successfully deposited on GO. The electrochemical glucose sensing performance of the as-prepared NiFe/GO was studied by cyclic voltammetry and amperometric measurement. Results showed that NiFe/GO modified glassy carbon electrode had sensitivity of 173 μA mM⁻¹cm⁻² for glucose sensing with a linear range up to 5 mM, which was superior to commonly used Ni nanoparticles. Furthermore, high selectivity for glucose detection can be achieved by NiFe/GO. All the results demonstrated that NiFe/GO hybrid was promising for using in electrochemical glucose sensing.

Recently published structural analysis and galvanomagnetic studies of a large number of different bulk and mesoscopic graphite samples of high quality and purity reveal that the common picture assuming graphite samples as a semimetal with a homogeneous carrier density of conduction electrons is misleading. These new studies indicate that the main electrical conduction path occurs within 2D interfaces embedded in semiconducting Bernal and/or rhombohedral stacking regions. This new knowledge incites us to revise experimentally and theoretically the diamagnetism of graphite samples. We found that the $c$-axis susceptibility of highly pure oriented graphite samples is not really constant but can vary several tens of percent for bulk samples with thickness $t \gtrsim 30~\mu$m, whereas by a much larger factor for samples with smaller thickness. The observed decrease of the susceptibility with sample thickness resembles qualitatively the one reported for the electrical conductivity and indicates that the main part of the $c-$axis diamagnetic signal is not intrinsic of the ideal graphite structure but it is due to the highly conducting 2D interfaces. The interpretation of the main diamagnetic signal of graphite agrees with the reported description of its galvanomagnetic properties and provides a hint to understand some magnetic peculiarities of thin graphite samples.

Stem cells are undifferentiated cells which can give rise to any types of cells in our body. Hence, they have been utilized for various applications such as drug testing and disease modeling. However, for the successful of those applications, the survival and differentiation of stem cells into specialized lineages should be well controlled. Growth factors and chemical agents are the most common signals to promote the proliferation and differentiation of stem cells. However, those approaches holds several drawbacks such as the negative side effects, degradation or denaturation, and expensive. To address such limitations, nanomaterials have been recently used as a better approach for controlling stem cells behaviors. Graphene oxide is the derivative of graphene, the first 2D materials in the world. Recently, due to its extraordinary properties and great biological effects on stem cells, many scientists around the world have utilized graphene oxide to enhance the differentiation potential of stem cells. In this mini review, we highlight the key advances about the effects of graphene oxide on controlling stem cell growth and various types of stem cell differentiation. We also discuss the possible molecular mechanisms of graphene oxide in controlling stem cell growth and differentiation.

The implementation of graphene-based electronics requires fabrication processes able to cover large device areas since exfoliation method is not compatible with industrial applications. Chemical vapor deposition of large-area graphene represents a suitable solution having the important drawback of producing polycrystalline graphene with formation of grain boundaries, which are responsible for limitation of the device performance. With these motivations, we formulate a theoretical model of graphene grain boundary by generalizing the graphene Dirac Hamiltonian model. The model only includes the long-wavelength regime of the particle transport, which provides the main contribution to the device conductance. Using symmetry-based arguments deduced from the current conservation law, we derive unconventional boundary conditions characterizing the grain boundary physics and analyze their implications on the transport properties of the system. Angle resolved quantities, such as the transmission probability, are studied within the scattering matrix approach. The conditions for the existence of preferential transmission directions are studied in relation with the grain boundary properties. The proposed theory provides a phenomenological model to study grain boundary physics within the scattering approach and represents per se an important enrichment of the scattering theory of graphene. Moreover, the outcomes of the theory can contribute in understanding and limiting detrimental effects of graphene grain boundaries also providing a benchmark for more elaborated techniques.

In this work, we firstly explored a mild, clean, and highly efficient approach for the synthesis of graphene quantum dots (GQDs). GQDs with carboxyl groups or amino groups, were prepared from one-pot environmentally friendly method assisted by hydrogen peroxide, respectively. It was proved that carboxyl groups played an important role in the fluorescence quenching. Based on these findings, we developed a novel fluorescent nanosensor by combining molecularly imprinted polymers (MIPs) with carboxyl functionalized GQDs for the determination of tetracycline (TC) in aqueous samples. The nanocomposite was prepared using a sol-gel process. GQDs-MIPs showed strong fluorescent emission at 410 nm when excited at 360 nm, which was subsequently quenched in the presence of TC. Under optimum conditions, the fluorescence intensity of GQDs-MIPs decreased in response to the increase of TC concentration with good linearity rage of 1.0-104 µg L-1. The limit of detection was determined to be 1 µg L-1. The fluorescence intensity of GQDs-MIPs was more strongly quenched by TC compared to the corresponding non-imprinted polymers, GQDs-NIPs. With the high sensitivity, the material was also successfully worked for the detection of TC in real spiked milk samples.

Mn3O4 /graphene nanosheets (GNS) composites serve as very excellent electrode materials for supercapacitors. They can fully combine the advantages of two materials such as graphene and metal oxide. Meanwhile, they can improve not only the specific energy and specific power of the materials, but also the cyclic stability of the materials. The results of the cyclic voltammetry and constant current charge discharge test on the composite electrode material have shown that the Mn3O4 /GNS powder sample has good capacitive performance. When the scanning rate is 5~50mV, the specific capacity retention rate of the composite electrode is 80.3% and 88% respectively. Mn3O4 nanoparticles, with the highest ratio of network coated GNS, exhibit a specific capacitance value of 957.6 F g−1 at a current density of 2 A g−1 in 1 M Na2SO4 solution. Besides, its network structure demonstrates high specific capacity and multiplying performance.

The focus of this research is to improve the performance of dye-sensitized solar cells (DSSC) through the adoption of high-quality FTO thin films and incorporation of graphene with DSSC photoanode to enhance its electrical transport. In this research, nanostructured FTO films were first grown with homemade Streaming Process for Electroless and Electrochemical Deposition technology (SPEED) using Tin (II) chloride dihydrate and ammonium fluoride and other chemical formulations. The FTO structural property was measured by X-ray diffraction (XRD); the films’ optical property was determined with transmittance spectra to curve over the wavelength range of 200-1000 nm measured with a spectrophotometer while scanning electron microscope (SEM) was used to determine the morphological properties of the samples. The electrical transport was evaluated by Hall Effect measurements at room temperature with a four-point probe. The FTO samples with the best structural, optical and electrical properties were employed as electrodes and counter electrodes of DSSC along with titanium dioxide. Thus, effect of graphene on the efficiency of DSSC was investigated. It was shown that a graphene-based DSSC showed an efficiency of 7.98% which is slightly higher than that of DSSC prototype without graphene (6.02%). The higher efficiency obtained with graphene can be credited to the ultrahigh surface area and thermal conductivity of graphene which tend to enhance the charge mobility and photovoltaic performance of DSSC. More research is however required to determine the exact amount of graphene that could achieve optimal DSSC performance. Further studies will also offer an adequate clarification for starting point of the better incorporation of graphene in DSSCs.

Electrochemical impedance (EI) measurements were performed to evaluate the nylon 66/-tetra-(para-aminophenyl) porphyrin (H₂T(p-NH₂)PP)/graphene oxide (GO) film coating on stainless steel and compared to the nylon/H₂T(p-NH₂)PP and nylon/GO film samples using 1M H₂SO₄ as electrolyte. The nylon/H₂T(p-NH₂)PP and nylon/GO composite films showed high electrochemical impedance in the order of 109 ohm-cm² and a system controlled by mass transfer, product of a diffusion process at low frequencies with a resistance up to 5 orders of magnitude, indicating the diffusion of protons through the coating and a decrease in the metal dissolution. Otherwise, the nylon/H₂T(p-NH₂)PP/GO film compound evaluated show good ionic conductivity and electrochemical stability in the acid environment, acting porphyrin as a catalyst to the passage of protons through the film, reducing its electrochemical impedance up to 7 orders of magnitude with respect to the compounds nylon/H₂T(p-NH₂)PP and nylon/GO. Likewise, good capacitance values are also shown by modifying the concentrations of porphyrin and GO reinforcing materials. These properties are important for technological applications, such as anticorrosion coating for bipolar plates or membrane in a fuel cell type PEM, super-capacitors, etc.

Ovarian cysts are linked to hormone imbalances and altered gene expressions, but the connection between cysts and ion channel expression is understudied. This study explored the role of TWIK-related acid-sensitive K+ (TASK) channels in bovine ovarian cyst formation. The ovarian follicles were split into small (5 to 10 mm in diameter) and large (> 25 mm in diameter) groups. Among the measured K+, Na+, and Cl- concentrations in follicular fluid (FF) obtained from small-sized follicles (SF) and large-sized follicles (LF), the K+ concentration was significantly lower in LFFF. Quantitative PCR, western blot, and immunocytochemistry data revealed that TASK-3 expression levels significantly decreased by approximately 50% in both LF and granulosa cells obtained from LF (LFGCs) compared to the corresponding controls. The TASK-3 protein was localized to the plasma membrane of GCs. The diameter of LFGCs was larger than that of SFGC. The cell swelling response to exposure to a hypotonic solution (200 mOsm/L) was highly reduced in TASK-3-overexpressing cells compared to vector-transfected cells. TASK-3-knockdown cells showed arrested growth. Senescence markers were detected in LFGCs and TASK-3-knockdown cells. These findings suggest that reduced TASK-3 expression in LF is associated with the inhibition of GC growth, leading to senescence and cyst formation.

Optical networks, characterized by using optical fibers as a transmission medium, constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is one of the key factors influencing optical network performance, it is important to comprehend its limitations and have the capability to estimate its value. In this context, we revisit the concept of capacity from various perspectives, including channel capacity, link capacity, and network capacity, thus providing an integrated view of the problem. Hence, we review the fundamental concepts behind optical networks, along with the basic physical phenomena present in optical fiber transmission and provide methodologies for estimating the different types of capacities, mainly using simple formulations. In particular, we propose a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with capacitated routing techniques for traffic routing. We apply this method to three reference networks and obtain capacities ranging from tens to hundreds of Terabits/s. Whenever possible, we also compare our results with published experimental data to understand how they relate.

The Cav3.2 T-type calcium channel is implicated in various pathological conditions, including cardiac hypertrophy, epilepsy, autism, and chronic pain. Phosphorylation of Cav3.2 by multiple kinases plays a pivotal role in regulating its calcium channel function. The calcium/calmodulin-dependent serine/threonine phosphatase, calcineurin, interacts physically with Cav3.2 and modulates its activity. However, it remains unclear whether calcineurin dephosphorylates Cav3.2, the specific spatial regions on Cav3.2 involved, and the extent of the quantitative impact. In this study, we elucidated the serine/threonine residues on Cav3.2 targeted by calcineurin using quantitative mass spectrometry. We identified six serine residues in the N-terminus, II-III loop, and C-terminus of Cav3.2 that were dephosphorylated by calcineurin. Notably, a higher level of dephosphorylation was observed in the Cav3.2 C-terminus, where calcineurin binds to this channel. Additionally, a previously known CaMKII-phosphorylated site, S1198, was found to be dephosphorylated by calcineurin. Furthermore, we also discovered that a novel CaMKII-phosphorylated site, S2137, underwent dephosphorylation by calcineurin. In CAD cells, a mouse central nervous system cell line, membrane depolarization led to an increase in the phosphorylation of endogenous Cav3.2 at S2137. Mutation of S2137 affected the calcium channel function of Cav3.2. Our findings advance the understanding of Cav3.2 regulation not only through kinase phosphorylation but also via calcineurin phosphatase dephosphorylation.

For massive multiple-input multiple-output (MIMO) communications, the minimum mean square error (MMSE) scheme provides close to optimal recognition but involves inverting the high-dimensional matrix. A Gauss-Seidel (GS) detector based on conjugate gradient and Jacobi iteration (CJ) joint processing is introduced to address this problem. Firstly, the signal is initialized with the best of the three initialization regimes for faster algorithm convergence. Secondly, the signal is processed together with CJ. Finally, the pre-processed result is transferred to the GS detector. The simulation results indicate that the proposed iterative algorithm has a lower BER performance than the GS and improved iterative scheme based on GS in channels with different correlation levels.

Electroencephalography (EEG) signals provide valuable insights into various activities of the human brain, including the detection of mental stress, which is a complex physiological and psychological response. However, the challenge lies in identifying mental stress accurately while mitigating the limitations associated with a large number of EEG channels. This includes issues such as computational complexity, the risk of overfitting, and the increased setup time for electrode placement, which can be cumbersome for real-life applications. Therefore, it is crucial to develop EEG channel selection algorithms that enable the creation of a wearable device capable of assessing mental stress in real-life scenarios. This study introduces a novel channel selection method aimed at identifying highly accurate channels for detecting mental stress. Our approach, known as the Correlation Coefficient of Hjorth Parameters (CCHP), assesses the correlation between activity, mobility, and complexity in the time domain to nominate the most relevant channels. By selecting channels that exhibit high correlation with the stress task while being uncorrelated with each other, CCHP significantly reduces the number of EEG channels required, without compromising accuracy or performance. To evaluate the effectiveness of CCHP, we conducted experiments using the DEAP public dataset. Comparing our results with other recent algorithms that utilize the full set of EEG channels, CCHP achieved a superior classification accuracy of 81.56% using only eight EEG channels. Furthermore, CCHP outperformed existing channel selection methods by an impressive 8%. These findings strongly indicate that the CCHP algorithm shows great promise in the design of a wearable application for mental stress detection, utilizing a minimal number of EEG channels.

Currently, the Israeli energy industry faces the challenge of a considerable increase in solar electricity production. Being a relatively isolated system, the significant expansion of solar electricity may cause problems with electricity quality. The electrical storage installation can resolve this problem. In Israel's situation, the optimal solution can be the creation of a channel between the Mediterranean and the Dead Sea. The channel can solve three closely related problems: the increased production of desalinated water for domestic, industrial, and agricultural needs; the prevention of a permanent Dead Sea level decline and its imminent disappearance; the development of hydro-pumping electrical storage stations; and the creation of numerous PV facilities in the Negev area for national electricity generation. However, a detailed analysis should be done for the estimation of the possible increase of solar electric generation with the consideration of a stochastic PV outcome and a potential ability to use the Dead Sea for the brine discharge from electrical hydro-storage plants.

How language mediates emotional perception and experience is poorly understood. The present event-related potential (ERP) study examined the explicit and implicit processing of emotional speech to differentiate the relative influences of communication channel, emotion category and task type in the prosodic salience effect. Thirty participants (15 women) were presented with spoken words denoting happiness, sadness and neutrality in either the prosodic or semantic channel. They were asked to judge the emotional content (explicit task) and speakers’ gender (implicit task) of the stimuli. Results indicated that emotional prosody (relative to semantics) triggered larger N100 and P200 amplitudes with greater delta, theta and alpha inter-trial phase coherence (ITPC) values in the corresponding early time windows, and continued to produce larger LPC amplitudes and faster responses during late stages of higher-order cognitive processing. The relative salience of prosodic and semantics was modulated by emotion and task, though such modulatory effects varied across different processing stages. The prosodic salience effect was reduced for sadness processing and in the implicit task during early auditory processing and decision-making but reduced for happiness processing in the explicit task during conscious emotion processing. Additionally, across-trial synchronization of delta, theta and alpha bands predicted the ERP components with higher ITPC values significantly associated with stronger N100, P200 and LPC enhancement. These findings reveal the neurocognitive dynamics of emotional speech processing with prosodic salience tied to stage-dependent emotion- and task-specific effects, which can reveal insights to research reconciling language and emotion processing from cross-linguistic/cultural and clinical perspectives.

Human ether-a-go-go-related gene (hERG) potassium channel is well-known contributor to drug-induced cardiotoxicity and therefore an extremely important target when performing safety assessments of drug candidates. Ligand-based approaches in connection with quantitative structure active relationships (QSAR) analyses have been developed to predict hERG toxicity. Availability of the recent published cryogenic electron microscopy (cryo-EM) structure for the hERG channel opened the prospect for using structure-based simulation and docking approaches for hERG drug liability predictions. In recent time, the idea of combining structure- and ligand-based approaches for modeling hERG drug liability has gained momentum offering improvements in predictability when compared to ligand-based QSAR practices alone. The present article demonstrates uniting the structure-based SILCS (site-identification by ligand competitive saturation) approach in conjunction with physicochemical properties to develop predictive models for hERG blockade. This combination leads to improved model predictability based on Pearson’s R and percent correct (represents rank-ordering of ligands) metric for different validation sets of hERG blockers involving diverse chemical scaffold and wide range of pIC50 values. The inclusion of the SILCS structure-based approach allows determination of the hERG region to which compounds bind and the contribution of different chemical moieties in the compounds to blockade, thereby facilitating the rational ligand design to minimize hERG liability.

Abstract The last mile has to deliver the goods at the right time and at the right cost for business logistics services to enhance the customer service experience. The objective of this paper is to examine the challenges of retail omni-channel distribution influencing the effective last mile fulfilment operations processes in the apparel group (organisation phase). It further establishes the extent of how the last mile for demand-driven store replenishment influences the level of retailers’ order fulfilment (in full and on time) (environment phase). This paper, persistently assesses the contribution of integrated information systems on brick and mortar and virtual omni-channel distribution networks to improve timeousness, order accuracy and fill rate (technology phase). The mixed method has triangulated the methods from both quantitative methodology using frequencies and binomial testing and subjective thematic analysis of qualitative data from interviewees. The sample of 175 questionnaires were received with a response rate is 85 per cent (148 responses). The main findings of the paper revealed that the current order fulfilment process aligned with the last mile is effective on the basis of the fill rate, lead time and order condition of orders delivered via store economy and store express.

The paper deals with the navigation data exchange between two satellites moving in a swarm. It is focused on reduction of the inter-satellite demanded communication channel capacity taking into account dynamics of the satellites relative motion and possible erasing in the channel the navigation data. The feedback control law is designed ensuring regulation of the relative satellites motion. The adaptive binary coding/decoding procedure for the satellites navigation data transmission over the limited capacity communication channel is proposed and studied for the cases of ideal and erasure channels. Dependence of the regulation time on the data transmission rate is numerically evaluated. Results of the numerical study of the closed-loop system performance and accuracy of the data transmission algorithm on the communication channel bitrate and erasure probability are obtained based on the extensive simulations. These results provide dependence of the required load of the communication channel on the desired quality of the regulation process. It is shown that both data transmission error and regulation time depend inversely proportional on the communication rate, and that for the significantly high data transmission rate erasure of data in the channel with probability up to 0.3 does not make an effect on the regulation time.

In recent years, CPU caches have revealed themselves as one of the most powerful sources of information leakage. This information leakage affects any implementation whose memory accesses, to data or instructions, depend on sensitive information such as private keys. In most cases, side-channel cache attacks do not require any specific permission and just need access to a shared cache. This fact, combined with the spread of cloud computing, where the infrastructure is shared between different customers, have made these attacks quite popular. In this paper, we present a novel approach to exploit the information obtained from the CPU cache. First, we introduce a non-access attack that provides a 97\% reduction in the number of encryptions required to obtain a 128-bit AES key. Next, this attack is adapted and extended in what we call the encryption-by-decryption cache attack or EBD, to obtain a 256-bit AES key. When EBD is applied to AES-256, we are able to obtain the 256 bits of the key with less than 10000 encryptions. These results make EBD, to the best of our knowledge, the first practical attack on AES-256 and also demonstrate that AES-256 is only about 3 times more complex to attack than AES-128 via cache attacks. In both cases the target is the AES T-table-based implementation, and we also demonstrate that our approach works in a cross-VM scenario.

We propose a deep-learning approach for the joint MIMO detection and channel decoding problem. Conventional MIMO receivers adopt a model-based approach for MIMO detection and channel decoding in linear or iterative manners. However, due to the complex MIMO signal model, the optimal solution to the joint MIMO detection and channel decoding problem (i.e., the maximum likelihood decoding of the transmitted codewords from the received MIMO signals) is computationally infeasible. As a practical measure, the current model-based MIMO receivers all use suboptimal MIMO decoding methods with affordable computational complexities. This work applies the latest advances in deep learning for the design of MIMO receivers. In particular, we leverage deep neural networks (DNN) with supervised training to solve the joint MIMO detection and channel decoding problem. We show that DNN can be trained to give much better decoding performance than conventional MIMO receivers do. Our simulations show that a DNN implementation consisting of seven hidden layers can outperform conventional model-based linear or iterative receivers. This performance improvement points to a new direction for future MIMO receiver design.

Miscarriage due to blastocyst implantation failure occurs in up to two-thirds of all miscarriage cases in human. The calcium ion has been shown to be involved in many cellular signal transduction pathways as well as in the regulation of cell adhesion, which is necessary for the embryo implantation process. Exposure to endocrine-disrupting chemicals (EDs) during early gestation results in disruption of intrauterine implantation and uterine reception, leading to implantation failure. In this study, ovarian estrogen (E2), bisphenol A (BPA), or 4-tert-octylphenol (OP), with or without ICI 182,780 (ICI) were injected subcutaneously from gestation day 1 to gestation day 3 post-coitus. The expression levels of the calcium transport genes were assessed in maternal uteri and implantation sites. The number of implantation sites was significantly low in the OP group, and implantation sites were absent in the E2 and EDs+ICI groups. There were different calcium transient transport channel expression levels in uterus and implantation site samples. The levels of TRPV5 and TRPV6 gene expression were significantly increased by EDs with/without ICI treatment in uterus. Whereas, TRPV5 and TRPV6 gene expression were significantly lower in implantation sites samples. NCX1 and PMCA1 mRNA levels were significantly decreased by OP and BPA in the implantation site samples. Compared to vehicle treatment in uterus, both the MUC1 mRNA and protein levels were markedly high in all but the BPA group. Taken together, these results suggest that both BPA and OP can impair embryo implantation through alteration of calcium transport gene expressions and by affecting uterine receptivity.

The Conus genus includes around 500 species of marine mollusks with a peculiar production of venomous peptides known as conotoxins (CTX). Each species is able to produce up to 200 different biological active peptides. Common structure of CTX is the low number of aminoacids stabilized by disulfide bridges and post-translational modifications that give rise to different isoforms. µ and µ-O CTX are two isoforms that specifically target voltage-gated sodium channels. These, by inducing the entrance of sodium ions in the cell, modulate the neuronal excitability by depolarizing plasma membrane and propagating the action potential. Hyperxcitability and mutations of sodium channels are responsible for perception and transmission of inflammatory and neuropathic pain states. In this review, we describe the current knowledge of µ-CTX interacting with the different sodium channels subtypes, the mechanism of action and their potential therapeutic use as analgesic compounds in the clinical management of pain conditions.

This review proposes an overview on the use of organic functionalized carbon nanostructures (CNSs) into solar energy conversion schemes. Our attention has focused in particular on the contribution given by organic chemistry to the development of new hybrid materials that find application in dye sensitized solar cells (DSSC), organic photovoltaics (OPV), perovskite solar cells (PSC) and also in photocatalytic fuel production, focusing in particular on the most recent literature. The request for new materials able to accompany the green energy transition that are abundant, low cost, with low toxicity, from renewable sources has further increased the interest in CNSs that meet all these requirements. The inclusion of an organic molecule, thanks to both covalent and non-covalent interactions, into a CNS, leads to the development of a completely new hybrid material able of combining and improving the properties of both starting materials. Besides the numerical data, which unequivocally state the positive effect of the new hybrid material, we hope that these examples can be inspiring for further research in the field of photoactive materials from an organic point of view.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with redox graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorporation of rGO would increase the interlayer spacing of NVO and diminish the charge transfer interactions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 94.54% of its initial specific capacity of 506.9 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

A tunable near-infrared surface plasmon resonance (SPR) biosensor based on gate-controlled graphene plasmons is investigated theoretically. The novel characteristics of chemical potential sensing make the proposed sensor promising in the application of ultra-sensitive and highly specific biosensing technology. The sensitivity of chemical potential sensing in wavelength interrogation mode can be calculated to be 1.5, 1.89, 2.29, 3.21, 3.73 and 4.68 nm/meV respectively at the central wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. The much smaller full width half maximum (FWHMs) comparing with that of 2D nanomaterial-enhanced metal SPR sensors indicates higher figure of merit. The sensitivity of chemical potential sensing in gate voltage interrogation mode also can be calculated to be 156.9822, 143.6147, 131.0779, 111.0351, 101.3415 and 90.6038 mV/meV respectively at the incident wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. It can be estimated theoretically that the limit of detection (LOD) in DNA sensing of the proposed sensor can reach femtomolar level and even attomolar level, comparable to and even lower than that of 2D nanomaterial-enhanced metal SPR sensors with AuNPs as a sensitivity enhancement strategy. The feasibility of preparation and operation of this new concept SPR biosensor is also analyzed and discussed.

Traditional graphene-based films normally possess high thermal conductivity (TC) only along single direction, which is not suitable for thermal interface materials (TIMs). Here, a graphene film with excellent bidirectional TC and mechanical properties was prepared by hot-pressing super-elastic graphene aerogel (SEGA). Thermal annealing at 1800℃ improves the further restacking of graphene sheets, bring the SEGA high structure stability for enduring the hot-pressing process. The junctions and nodes between the graphene layers in the hot-pressed SEGA (HPSEGA) film provide bidirectional heat transport paths. The in-plane TC and through-plane TC of HPSEGA film with thickness of 101μm reach 740 Wm-1K-1 and 42.5 Wm-1K-1, respectively. In addition, HPSEGA film with higher thickness still maintains excellent thermal transport properties due to the interconnected structure reducing the effect of the defects. The infrared thermal images visually manifest the excellent thermal-transfer capability and thermal dissipation efficiency of the HPSEGA films, indicating the great potential as advanced bidirectional TIMs.

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide-polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment.

(1) Background: The study aimed to investigate compressive strength for three computer-aided design/computer-aided manufacturing (CAD/CAM) dental materials: glassceramic IPS Empress CAD (IvoclarVivadent), hybrid ceramic Cerasmart (GC) and polymer-reinforced graphene G-CAM (Graphenano Dental). (2) Methods: 45 samples consisted of the molar crowns fabricated by three CAD/CAM materials were cemented adhesively on 3D printed abutments (Asiga DentalResin). The samples were divided into 3 groups (n=15) according to the crowns thickness; group 1 under the cusps/cervical margins - 0.6 mm/0.4 mm, group 2 - 1 mm/0.7 mm respectively, and group 3 - 1.5 mm/1 mm. Additionally, 20 cylindrical specimens fabricated by the three crowns and abutments material (n=5) were prepared by CAD/CAM technique. All samples and specimens were subjected to an axial compressive load by using a universal testing machine (Instron 3366-10kN, USA) until fracture. (3) Results: The compressive strength were for Empress CAD 1258 MPa, Cerasmart 501.3 MPa, G-CAM 435 MPa and Asiga resin 360 MPa. G-CAM crowns exhibited a higher maximum compressive load (1701.5-2011.8N) than both Cerasmart (1295.4-1642.9N) and Empress CAD (494.3-597.5N). (4) Conclusions: The CAD/CAM crown materials presented different mechanical behavior; Empress CAD and Cerasmart presented a fragile behavior, with a high compressive strength when compared to G-CAM and Asiga resins.

In the work the enhanced security of unmanned aerial vehicles (UAVs) electronics in RF environment was investigated. UAVs are commonly used in many areas and the cellular networks as the parallel helping networks for systems: LTE, 5G or especially for future 6G are very perspective and needed. For effective communications in channels: “air-to-ground” as well as “drone-to-drone” the important task is undisturbed work of transportation platforms, ie. UAV. However, high level of outside electromagnetic radiation can affect the correct electronics work. The problem is due to non-conformity of RF environment regulations. The electromagnetic compatibility (EMC) standards guarantee correct electronics work when the radiation level is not higher than established EMC levels. In case of commercially available devices, like UAVs, this level is 3 V/m. On the other hand, permissive exposure level, treated as RF environment emitted by cellular base stations, can reach the level of 61 V/m. Such level of electromagnetic wave pollution, can damage unprotected electronics with fatal consequences. This can cause the unchecked drone flight or unchecked fall down. As a result, due to unchecked flight, the UAV can cause the sudden communication interruption with operator or other drones. To reduce the level of damaging RF field we propose to cover the UAV housing with microwave absorber. In this case absorber must ensure good electromagnetic protection as well as lightweight and resistant on weather conditions. The shielding property of reduced graphene oxide (RGO) as an absorber was investigated. For proposed material the shielding effectiveness (SE) was investigated in the frequency range from 100 MHz to 10 GHz. It has been proved that such material can be a good candidate as an absorber for UAV having low reflection coefficient and high absorption ability. In this work the shielding effectiveness of RGO was analyzed for two layers of 3 and 5 mm at typical frequencies as RF environment, ie. 3.6 GHz (5G system) and 5.8 GHz (LTE). Investigated absorber guarantees the value of SE of 25 dB and 30 dB for 3 mm layer at 3.6 GHz and 5.8 GHz respectively and of 29 dB and 39.5 dB for 5 mm layer at these frequencies respectively.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.

Graphene quality for use in biosensors was assessed in fabricated chips by a set of methods that includes atomic force microscopy (AFM), Raman spectroscopy, and low-frequency noise. It is shown that local areas of residues on the graphene surface, which arisen due to the interaction of graphene with a photoresist at the initial stage of chips development, leads to a spread of chips resistance (R) within 1-10 kΩ and to an increase in the root mean square (RMS) roughness up to 10 times that can significantly impair reproducibility of graphene parameters in biosensors chips. It was observed that the control of the photoresist residues after photolithography (PLG) by AFM and subsequent additional cleaning allow reducing the spread of R values in chips to 1–1.6 kΩ and obtaining RMS roughness similar to the roughness in pristine graphene before PLG. Monitoring of the spectral density of low-frequency voltage fluctuation (SU), which provides integral information about the defect system and quality of the material, makes it possible to identify chips with low graphene quality and with inhomogeneously distributed compressive stresses areas by the type of frequency dependence SU (f).

Graphene-based nanomaterials have emerged as promising materials for a wide range of applications.. Therefore, in the last years carbon nanoparticles have attracted great attention due to their low toxicity, high biocompatibility and easy preparation. Recently, N-doped carbon nanoparticles have been shown to have improved antibacterial activity over the undoped nanomaterial, but it is difficult to find correlations between the structure of the nanoparticle and its antibacterial activity. With this purpose, here, we analyze the effect of both, the nanoparticle size and the surface chemical composition of four N-doped carbon nanoparticles on the growth of Escherichia coli bacteria. Our results were analyzed using a Ligand-Substrate model based on the Monod´s equation, which allows us to interpret the dependence of the nanoparticle-bacteria affinity with the nanomaterial structure.

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

We demonstrate that the conductivity of graphene on thin-film polymer substrates can be accurately determined by reflection-mode air-plasma-based THz time-domain spectroscopy (THz-TDS). The phase uncertainty issue associated with reflection measurements is discussed, and our implementation is validated by convincing agreement with graphene electrical properties extracted from more conventional transmission-mode measurements. Both the reflection and transmission THz-TDS measurements reveal strong nonlinear and instantaneous conductivity depletion across an ultra-broad bandwidth under relatively high incident THz electrical field strengths.

Mechanically strong and thermally stable films obtained from a water-based polyurethane (PU) dispersion with small (0.1–1.5 wt.%) additions of graphene oxide nanosheet (GO) were studied through elemental analysis, X-ray photoelectron spectroscopy, differential thermogravimetry, and Raman spectroscopy. Moreover, the depletion of near-surface layers in nitrogen was presented for all the samples under study. It was found that the introduction of GO into a PU matrix was ac-companied by a partial reduction of graphene oxide nanosheet and an increase in the concentra-tion of defects in its structure.

Understanding the catalytic performance of different materials is of crucial importance for further technological advancements. This especially relates to the behavior of different classes of catalysts under operating conditions. Here we analyze the effects of local coordination of metal centers (Mn, Fe, Co) in graphene-embedded Single-Atom Catalysts (SACs). We have started from well-known M@N4-graphene catalysts and systematically replaced nitrogen atoms with oxygen or sulfur atom to obtain M@OxNy-graphene and M@SxNy-graphene SACs (x+y=4). We show that local coordination strongly affects the electronic structure and the reactivity towards hydrogen and oxygen species. However, the stability is even more affected. Using the concept of Pourbaix plots, we show that the replacement of nitrogen atoms coordinating metal center with O or S destabilizes SACs towards the dissolution, while the metal centers get easily covered by O and OH acting as additional ligands at high anodic potentials and high pH values. Thus, not only should local coordination be considered in terms of the activity of SACs, but it is also necessary to consider its effects on the speciation of SACs' active centers under different potential and pH conditions.

We experimentally investigate power-sensitive photo-thermal tuning (PTT) of two-dimensional (2D) graphene oxide (GO) films coated on integrated optical waveguides. We measure the light power thresholds for reversible and permanent GO reduction in silicon nitride (SiN) waveguides integrated with 1 and 2 layers of GO. Raman spectra at different positions of a hybrid waveguide with permanently reduced GO are characterized, verifying the inhomogeneous GO reduction along the direction of light propagation through the waveguide. The differences between the PTT induced by a continuous-wave laser and a pulsed laser are also compared, confirming that the PTT mainly depend on the average input power. These results reveal interesting features for 2D GO films coated on integrated optical waveguides, which are of fundamental importance for the control and engineering of GO’s properties in hybrid integrated photonic devices.

We experimentally demonstrate enhanced self-phase modulation (SPM) in silicon nitride (Si₃N₄) waveguides integrated with 2D graphene oxide (GO) films. GO films are integrated onto Si₃N₄ waveguides using a solution-based, transfer-free coating method that enables precise control of the film thickness. Detailed SPM measurements are carried out using both picosecond and femtosecond optical pulses. Owing to the high Kerr nonlinearity of GO, the hybrid waveguides show significantly improved spectral broadening compared to the uncoated waveguide, achieving a broadening factor of up to ~3.4 for a device with 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of up to 18.4 and a Kerr coefficient (n₂) of GO that is about 5 orders of magnitude higher than Si₃N₄. Finally, we provide a theoretical analysis for the influence of GO film length, coating position, and its saturable absorption on the SPM performance. These results verify the effectiveness of on-chip integrating 2D GO films to enhance the nonlinear optical performance of Si₃N₄ devices.

We theoretically investigate and optimize the performance of four-wave mixing (FWM) in microring resonators (MRRs) integrated with two-dimensional (2D) layered graphene oxide (GO) films. Owing to the interaction between the MRRs and the highly nonlinear GO films as well as to the resonant enhancement effect, the FWM efficiency in GO-coated MRRs can be significantly improved. Based on previous experiments, we perform detailed analysis for the influence of the GO film parameters and MRR coupling strength on the FWM conversion efficiency (CE) of the hybrid MRRs. By optimizing the device parameters to balance the trade-off between the Kerr nonlinearity and loss, we achieve a high CE enhancement of ~18.6 dB relative to the uncoated MRR, which is ~8.3 dB higher than previous experimental results. The influence of photo-thermal changes in the GO films as well as variations in the MRR parameters such as the ring radius and waveguide dispersion on the FWM performance is also discussed. These results highlight the significantly improved FWM performance that can be achieved in MRRs incorporating GO films

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

We specify basic definitions of the Chern-Simons current in cohomology theory, then we calculate its value by using a model of quantum machine learning, the so-called supersymmetric support Dirac machine. The supercurrent is generated from the coupling between three states of a quantum flux of modified Wilson loop of the Cooper pairs. We use Holo-Hilbert spectrum in frequency modulation to visualize the network as a coupling behavior of convolutional neuron network in superstatistical theory with the application to the theory of a superconductor. We also calculate the number of carbon atoms in the stable support spinor network structure of a graphene wormhole to produce a supercurrent of Cooper pairs as graviphoton states by using the Holo-Hilbert spectral analysis.

Layered two-dimensional (2D) GO films are integrated with silicon-on-insulator (SOI) nanowire waveguides to experimentally demonstrate an enhanced Kerr nonlinearity, observed through self-phase modulation (SPM). The GO films are integrated with SOI nanowires using a large-area, transfer-free, layer-by-layer coating method that yields precise control of the film thickness. The film placement and coating length are controlled by opening windows in the silica cladding of the SOI nanowires. Owing to the strong mode overlap between the SOI nanowires and the highly nonlinear GO films, the Kerr nonlinearity of the hybrid waveguides is significantly enhanced. Detailed SPM measurements using picosecond optical pulses show significant spectral broadening enhancement for SOI nanowires coated with 2.2-mm-long films of 1−3 layers of GO, and 0.4-mm-long films with 5−20 layers of GO. By fitting the experimental results with theory, the dependence of GO’s n₂ on layer number and pulse energy is obtained, showing interesting physical insights and trends of the layered GO films from 2D monolayers to quasi bulk-like behavior. Finally, we show that by coating SOI nanowires with GO films the effective nonlinear parameter of SOI nanowires is increased 16 fold, with the effective nonlinear figure of merit (FOM) increasing by about 20 times to FOM > 5. These results reveal the strong potential of using layered GO films to improve the Kerr nonlinear optical performance of silicon photonic devices.