The bio-oil was largely produced by thermal pyrolysis of Jatropha-derived biomass wastes (denoted as Jatropha bio-oil) using a Pilot Plant with a capacity of 20 kg h-1 at Thailand Institute of Scientific and Technological Research (TISTR), Thailand. Jatropha bio-oil is an unconventional type of bio-oil, which is mostly composed of fatty acids, fatty acid methyl esters, fatty acid amides and derivatives, and consequently it contained large amounts of heteroatoms (oxygen ~ 20 wt.%, nitrogen ~ 5 wt.%, sulfur ~ 1000 ppm.). The heteroatoms, nitrogen especially, are highly poisonous to the metal or sulfide catalysts for upgrading of Jatropha bio-oil. To overcome this technical problem, we reported a stepwise strategy for hydrotreating of 100 wt% Jatropha bio-oil over mesoporous sulfide catalysts of CoMo/γ-Al2O3 and NiMo/γ-Al2O3 to produce drop-in transport fuels, such as gasoline- and diesel-like fuels. This study is very different from our recent work on co-processing of Jatropha bio-oil (ca. 10 wt%) with petroleum distillates to produce a hydrotreated oil as a diesel-like fuel (Chen et al., Catalysts 2018, 8, 59; http://dx.doi.org/10.3390/catal8020059). Jatropha bio-oil was pre-treated through a slurry-type high pressure reactor under severe condition, resulting in a pre-treated Jatropha bio-oil with relatively low amounts of heteroatoms (oxygen < 20 wt.%, nitrogen < 2 wt.%, sulfur < 500 ppm.). The light and middle distillates of pre-hydrotreated Jatropha bio oil was then separated by distillation at temperature below 240 oC, and the temperature of 240-360 oC. Deep hydrotreating of light distillates over sulfide CoMo/γ-Al2O3 catalyst was performed on a batch-type high pressure reactor at 350 oC and 7 MPa of H2 gas for 5 h. The hydrotreated oil was a gasoline-like fuel, which contained 29.5 vol.% of n-paraffins, 14.4 vol.% of iso-paraffins, 4.5 vol.% of olefins, 21.4 vol. % of naphthene compounds and 29.6 wt.% of aromatic compounds, and little amounts of heteroatoms (nearly no oxygen and sulfur, and less than 50 ppm of nitrogen), corresponding to an octane number of 44, and it would be suitable for blending with petro-gasoline. The hydrotreating of middle distillates over sulfide NiMo/γ-Al2O3 catalyst using the same reaction condition produced a hydrotreating oil with diesel-like composition, low amounts of heteroatoms (no oxygen and less than 50 ppm of sulfur and nitrogen), and a cetane number of 60, which would be suitable for use in drop-in diesel fuel.

This work studies a novel low voltage (<60 V) hybrid system that supports engine boosting and downsizing in addition to start-stop, regenerative braking, and constrained torque assist/regeneration. The hybrid power split supercharger (PSS) shares a 9 kW motor between supercharging the engine or providing hybrid functionalities through a planetary gear set, a brake and a bypass valve. The PSS operation is limited to only one of the parallel hybrid or boosting modes at a time, necessitating a highly optimized decision making algorithm to select the device mode and power split ratio. In this work an adaptive equivalent consumption minimization strategy (A-ECMS) is developed for energy management of the PSS. The A-ECMS effectiveness is compared against a dynamic programming (DP) solution with full drive cycle preview through hardware-in-the-loop experiments on an engine dynamometer testbed. The experiments show that the PSS with A-ECMS reduces a vehicle fuel consumption by 18.4% over standard FTP75 cycle compared to a baseline turbocharged engine, while global optimal DP solution decreases the fuel consumption by 22.8% compared to baseline.

The rising of an oil drop in a non-Newtonian viscous solution is studied experimentally. In this case, the shape of the ascending drop is strongly affected by the non-Newtonian properties of the surrounding liquid. We found that the so-called velocity discontinuity phenomena is observed for drops larger than a certain critical size. Beyond the critical velocity, the formation of a long tail is observed, from which small droplets are continuously emitted. We determined that the fragmentation of the tail results mainly from the effect of capillary effects. We explore the idea of using this configuration as a new encapsulation technique, where the size and frequency of droplets can be well predicted.

To obtain drop-in fuel properties from non-feed biomass, we herein report the catalytic hydrotreatment of microalgae biocrude, produced from hydrothermal liquefaction (HTL) of Spirulina. Our contribution focuses on the effect of temperature, initial H2 pressure, and residence time on the removal of heteroatoms (O and N). In contrast to common hydrotreating experimental protocols at batch scale, we devised a set of two-level factorial experiments and studied the most influential parameters affecting the removal of heteroatoms. It was found that up to 350 °C, the degree of deoxygenation (de-O) is mainly driven by temperature, whereas the degree of denitrogenation (de-N) also relies on initial H2 pressure and temperature-pressure interaction.Based on this, complete deoxygenation was obtained at mild operating conditions (350 °C), reaching a concurrent 47 % denitrogenation. Moreover, three optimized experiments are reported with 100 % removal of oxygen. In addition, the analysis by GC-MS and Sim-Dis gives insight to the fuel quality. The distribution of heteroatom N in lower (<340 °C) and higher (>340 °C) fractional cuts is studied by a fractional distillation unit following ASTM D-1160. Final results show that 63-68 % of nitrogen is concentrated in higher fractional cuts.

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

Brimonidine, a selective alpha-2 adrenergic agonist, used for treatment of open-angle glaucoma, has been shown to cause neurological side effects such as unresponsiveness, lethargy, hypoventilation, and stupor, mimicking opioid toxicity. We report one case of transient encephalopathy in a toddler, in whom brimonidine accidental toxicity was sus-pected and then confirmed by a toxicology study. The 8-month-old healthy girl child was taken to the pediatric ER since she was drowsy and hypotonic, with miosis. Brain CT scan and toxicological work-up on blood and urine were negative. Starting from hour +4, the child progressively improved, and by hour +6, she recovered to a normal state of consciousness. A survey of available drugs at the child’s reach showed the presence of brimonidine. Thus, ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS) was applied to quantify brimonidine in urine and plasma samples, showing 8.40 ng/mL level and 0.79 ng/mL, respectively. To our knowledge, this is the first report for determining brimonidine levels in urine and plasma by UPLC-MS/MS. Insufficient knowledge of the family members about the potential hazards of an apparently innocuous, topical medication such as eye drops may put children at a greater risk of poisoning. Necessary warnings should be better given to parents when prescribing this medication.

The present study evaluates the response to betahistine in patients who presented vestibular drops attacks in the context of Ménière's disease (MD) and the factors that can predict an unfavorable response to it. A total of 43 patients were analyzed, out of which 33 were diagnosed with MD. It is a descriptive, cross-sectional study with retrospective data collection. Data as regards age, accompanying symptoms, etiological diagnosis and response to MD treatment were collected. A statistical analysis was carried out, and we found that the disease evolution time and specific alterations in the vestibulospinal and oculomotor physical examination present an unfavorable response to betahistine, as opposed to the use of intratympanic gentamicin, with which symptomatic control is achieved in 100% of the cases.

Drops are the most important and most common energy dissipator in irrigation networks and erodible canals and consequently, their performance must be well understood. This study was designed to evaluate the capability of Artificial Intelligence (AI) methods including ANN, ANFIS, GRNN, SVM, GP, MLR, and LR to predict the relative energy dissipation (∆E/E0) in vertical drops equipped with a horizontal screen. For this study, 108 experiments were carried out to investigate energy dissipation with variable discharge, varying drop height, and porosity of the horizontal screens. Parameters yc/h, yd/yc, and p are considered as input variables and ∆E/E0 is the output variable. The efficiency of models was compared using Taylor's diagram, Box Plot of the applied error distribution, correlation coefficient (CC), mean absolute error (MAE) and root-mean-square error (RMSE). Results indicate that the performance of the ANFIS_gbellmf based model with CC value of 0.9953, RMSE value of 0.0069 and MAE value of 0.0042 was superior to other applied models. Also, the linear regression model with CC=0.9933, RMSE=0.0083, and MAE= 0.0067performs better than the multiple linear regression model in this study. Results of a sensitivity study suggest that yc/h is the most effective parameter for predicting ∆E/E0.

Low-resource languages often face the problem of insufficient data, which leads to poor quality in machine translation. One approach to address this issue is data augmentation. Data augmentation involves creating new data by transforming existing data through methods such as flipping, cropping, rotating, and adding noise. Traditionally, pseudo-parallel corpora are generated by randomly replacing words in low-resource language machine translation. However, this method can introduce ambiguity as the same word may have different meanings in different contexts. This study proposes a new approach for low-resource language machine translation, which involves generating pseudo-parallel corpora by replacing phrases. The performance of this approach is compared with other data augmentation methods, and it is observed that combining it with other data augmentation methods further improves performance. To enhance the robustness of the model, R-Drop regularization is also used. R-Drop is an effective method for improving the quality of machine translation. The proposed method was tested on Chinese-Kazakh (Latin script) translation tasks, resulting in performance improvements of 4.99 and 7.7 for Chinese-to-Kazakh and Kazakh-to-Chinese translations, respectively.

Numerical simulations and experiments on evaporative condensers in air conditioning systems using R744 were performed. Two configurations were given to study the feasibility of operating the subcritical R744 cycle. It indicated the capable of evaporative cooling condensing R744 to liquify by analyzing the outlet temperature at the end of the condenser reached from 28.7oC to 30.3oC with the operating pressure from 72.6 bar to 68.5 bar. The mass flow rate in the study increases from 14.34 kg/h to 46.08 kg/h, the pressure drop also increases from 0.23 bar to 0.47 bar for the simulation and 0.4 bar to 0.5 bar for the experiment, respectively. This study indicates that a 5-layers of copper tubes configuration causes a higher pressure drop and lower COP when compared to an 8-layers of copper tubes that split into 2 sets for smaller pressure drop. In this study, the evaporative condensers using mini tubes that are flooded in the cooling water tank are suitable for the subcritical R744 air conditioning system. The results obtained from the experimental data are in good agreement with those obtained from the numerical results, with the deviation less than 5%.

Registration of the flow pattern fine structure and the matter distribution of a free falling liquid drop in a target fluid at rest in the impact mode of coalescence, when the kinetic energy of the drop exceeds its available potential surface energy (APSE), was carried out by photo and video recording. The main attention was paid to the study of the flow structure at the initial stage of the cavity formation. To carry out color registration, the flow pattern was illuminated by several matrix LED and fiber optic sources of constant light. The planning of experiments and interpretation of the results were based on the properties of the complete solutions of the fundamental equations of fluid mechanics system, including the transfer and conversion of energy processes. Complete solutions of the system of equations describe large-scale flow components that are waves or vortices as well as thin jets (ligaments, filaments, fibers, trickles). In experiments, the jets are accelerated by the converted available potential surface energy (APSE) when the free surfaces of merging fluids were eliminated. The experiments were performed with the coalescence of water, solutions of alizarin ink, potassium permanganate, copper sulphate or iron sulphate drops in deep water. In all cases, at the initial contact, the drop begins to lose its continuity and breaks up into a thin veil and jets, the velocity of which exceeds the drop contact velocity. Small droplets, the size of which grows with time, are thrown into the air from spikes at the jet tops. On the surface of the liquid, the fine jets leave colored traces that form linear and reticular structures. Part of the jets penetrating through the bottom and wall of the cavity forms an intermediate covering layer. The forming layer jets are separated by interfaces of the target fluid. The processes of molecular diffusion equalize the density differences and form an intermediate layer with sharp boundaries in the target fluid. All noted structural features of the flow are also visualized when a fresh water drop isothermally spreads in the same tap water. The fast-changing and finely structured diffuse boundary of merging fluids, which at the initial stage has a complex and irregular shape, is gradually smoothed out by molecular diffusion processes. The similar flow patterns were observed in all performed experiments, however the geometric features of the flow depend on the individual thermodynamic and kinetic parameters of the contacting fluids.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

This pioneering study presents an in-depth biomechanical examination of soccer's diving header, aiming to quantify its impact on ball speed enhancement (BSE) and effective offensive range (EOR). Despite the diving header's widespread acclaim and historical significance, there remains a dearth of scientific scrutiny into its biomechanical intricacies. Employing an innovative research design featuring a static hanging ball at varied offensive distances and heights, the study replicates diverse header scenarios. The results of 3D motion quantification have shown that a physically excellent player (identified through the maximal standing long jump test) could reach an EOR around 2.64 times his body height. Furthermore, the study unveils that proficient players could attain BSE surpassing 9 m/s, signifying the diving header's heightened efficacy compared to traditional heading techniques, which could only result in 4.5 m/s. Correlation analyses unveil noteworthy relationships, highlighting the pivotal role of head speed at impact and the influence of minimizing speed-drop and temporal disparities for amplified effectiveness. Considerations for optimizing diving header execution are introduced, emphasizing the necessity for targeted training programs. Despite acknowledged limitations inherent to its pilot nature, this exploration furnishes foundational knowledge to guide subsequent research and practical applications, providing valuable insights into soccer training and skill development through a biomechanical lens.

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

Semiconductor nanowhiskers, in particular, nanostructured whiskers based on zero-dimensional (0D) C70 fullerene, are being actively discussed due to the great potential of their application in modern electronics. For the first time, we proposed and implemented a method for the synthesis of nanostructured C70 fullerene whiskers based on the self-organization of C70 molecules during thermal evaporation of C70 droplets on the substrate surface. We found that the onset of the synthesis of C70 nanowhiskers upon evaporation of drops of a C70 solution in toluene on the substrate surface depends on the substrate temperature. We have provided experimental evidence that an increase in both the C70 concentration in the initial drop and the substrate temperature leads to an increase in the geometric dimensions of C70 nanowhiskers. The obtained results provide useful vision on the role of solute concentration and substrate temperature in the synthesis of one-dimensional materials.

The effect of coal hydrophilic particles in water-glycerol drops on the maximum diameter of spreading along a hydrophobic solid surface is experimentally studied by analyzing the velocity of internal flows by Particle Image Velocimetry. The grinding fineness of coal particles was 45-80 μm and 120-140 μm, their concentration was 0.06 wt.% and 1 wt.%. The impact of particle-laden drops on a solid surface occurred at Weber numbers (We) from 30 to 120. It is revealed the interrelated influence of We and the concentration of coal particles on changes in the maximum absolute velocity of internal flows in a drop within the kinetic and spreading phases of the drop-wall impact. A physical model is formulated for internal convective flows in the longitudinal section of a drop parallel to the plane of the solid wall. The kinetic energy of translational motion of coal particles in a spreading drop compensates for the energy expended by the drop on sliding friction along the wall. At We=120, the inertia-driven spreading of the particle-laden drop is mainly determined by the dynamics of the deformable Taylor rim. An increase in We contributes to more noticeable differences in the convection velocities in spreading drops. When the drop spreading diameter rises at the maximum velocity of internal flows, a growth of the maximum spreading diameter occurs. The presence of coal particles causes a general tendency to reduce the drop spreading.

The aim of this study is to provide the scientists with a straightforward correlation that can be applied for predicting the Fanning friction factor and consequently the pressure drop during blood flow in small caliber vessels. Due to the small diameter of the conduit, the Reynolds numbers are low and thus the flow is laminar. The study has been conducted using CFD simulations validated with relevant experimental data acquired using an appropriate experimental set-up. The experiments concern pressure drop measurement during the flow of a blood analogue that follows the Casson model, i.e. an aqueous glycerol solution that contains a small amount of xanthan gum and exhibits similar behavior to blood, in a smooth, stainless steel microtube (L=5.6cm and D=400 μm). The interpretation of the resulting numerical data led to the proposal of a simplified model that incorporates the effect of the flow rate, the hematocrit value (35-55%) and the vessel diameter (300-1800 μm) and predicts with better than ±10% the Fanning friction factor and consequently the pressure drop during laminar blood flow in small caliber vessels.

An analysis of the performance of Automatic Dependent Surveillance-Broadcast (ADS-B) data received from the Grand Forks, North Dakota International Airport was carried out in this study. The purpose was to understand the vulnerabilities of Universal Access Transceiver (UAT) ADS-B system and recognize the effects on present and future Air Traffic Control (ATC) operation. The Federal Aviation Administration (FAA) mandated all the General Aviation aircraft to be equipped with ADS-B. The aircraft flying within United States and below the transition altitude (18,000 feet) are more likely to install an UAT ADS-B. At present unmanned aircraft systems (UAS) and autonomous air traffic control (ATC) towers are being integrated into the aviation industry and UAT ADS-B is a basic sensor for both class 1 and class 2 Detect and Avoid (DAA) systems. As a fundamental component of future surveillance system, the anomalies and vulnerabilities of ADS-B system need to be identified to enable a fully utilized airspace with enhanced situational awareness. The data received was archived in GDL-90 format, which was parsed into readable data. The anomaly detection of ADS-B messages was based on the FAA ADS-B performance assessment report. The data investigation revealed ADS-B message suffered from different anomalies including drop out; missing payload; data jump; low confident data and altitude discrepancy. Among those studied, the most severe was drop out and 32.49% of messages suffered from this anomaly. Dropout is an incident where ADS-B failed to update within a specified rate. Considering the potential danger being imposed, an in-depth analysis was carried out to characterize message dropout. Three flight parameters were selected to investigate their effect on drop out. Statistical analysis was carried out and Friedman Statistical Test identified that altitude affected drop out more than any other flight parameters.

This work analyzes the severity and risk associated with Automatic Dependent Surveillance-Broadcast (ADS-B) message drop out in Detect and Avoid (DAA) function of Unmanned Aircraft System (UAS). Performance assessment of the Universal Access Transceiver (UAT) ADS-B message implies that in some cases ADS-B fails to update within a specified update interval, which is referred to as drop out in this work. ADS-B is a fundamental surveillance sensor for both class 1 and class 2 DAA systems. Message loss or drop out has been found as one of the common limitations of the ADS-B system. The key feature of this study is incorporating the update rate of real ADS-B data transmitted from the manned aircraft. The data were received from the Grand Forks International Airport, North Dakota. Monte Carlo method has been adopted to resolve encounter scenarios in the presence of drop out. The change in the alert triggered by the UAS DAA in the presence of ADS-B drop out has been investigated. Furthermore, the risk matrices are created to quantify the associated risk with drop out affected alerts. Simulation results depict that both the duration of drop out and DAA look-ahead time affect the alert-triggering function of UAS. With a small look- ahead window and longer duration of drop out, the number of warning alerts increases. Also, alerts are affected more during an overtaking encounter than that of a head-to-head encounter. A system-level analysis is also carried out to recognize the potential reasons behind the ADS-B drop out.

Foot drop is a common disability in post-stroke patients and represents a challenge for the clinician. To date, Ankle Foot Orthosis (AFO) combined with conventional rehabilitation is the gold standard of rehabilitation management. AFO has a palliative mechanical action without actively restoring the associated neural function. Functional Electrical Stimulation (FES), consisting in stimulation of the peroneal nerve pathway, represents an alternative approach. By providing a FES device (Bioness L-300, BIONESS, USA) for 6 months to a post-stroke 22-year-old woman with a foot drop, our goal was to quantify its potential benefit on walking capacity. Gait parameters and the temporal evolution of the speed were collected with a specific connected sole device (Feet Me®) during the 10-meter walking, the Time Up and Go, and the 6-minute walking tests with AFO, FES or without any device (NO). As a result, the walking speed changes on 10-meters were clinically significant with an increase from baseline to 6 months in AFO and FES conditions (+0.14m-1 and +0.36m-1), without any changes in NO condition. In addition, speed decreased at about 4-minutes of the 6-minute walking test in NO and AFO conditions, while speed increased in FES conditions at baseline and after 1, 3 and 6 months. Monitoring gait speed in an endurance test after an ecological rehabilitation training program helps to examine walking performance in post-stroke patients and to propose a specific rehabilitation program depending on a fatigue threshold.

The research presents the inter-comparison of atmospheric variables measured by 9 automatic meteorological stations. This set of data was compared with the measurements of other meteorological stations in order to standardize the values that must be adjusted when taken to different areas. The data of a set of a total of 9 GMX500, which measures conventional meteorological variables, and 10 WS100 sensors, which measures precipitation parameters. The automatic stations were set up at the Huancayo Observatory (Geophysical Institute of Peru) for a period of 5 months. The data set of GMX500 were evaluated comparing with the average of the 9 sensors and the WS100 was compared with a optical disdrometer Parsivel2. The temperature, pressure, relative humidity, wind speed, rainfall rate, and drop size distribution was evaluated. A pair of GMX500 sensors presented high data dispersion, it was found found that the errors came from a bad configuration; once this problem was solved, good agreement was archived, with low RMSE and high correlation. I was found that the WS100 sensors overestimate the precipitation with a percent bias close to 100% and the differences increase with the greater intensity of rain. The DSD retrieved by WS100 have unrealistic behavior with higher concentrations in diameters of 1 mm and 5 mm, in addition to a flattened curve.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

The contactless coalescence of a droplet is of paramount importance for physical and industrial applications. This paper describes a coalescence method in mid-air via acoustic levitation using an ultrasonic phased array system. Acoustic levitation using ultrasonic phased arrays provides promising lab-on-a-drop applications, such as transportation, coalescence, mixing, separation, evaporation, and extraction in a continuous operation. The mechanism of droplet coalescence in mid-air may be better understood by experimentally and numerically exploring the droplet dynamics immediately before the coalescence. In this study, water droplets were experimentally levitated, transported, and coalesced by controlling acoustic fields. We observed that the edge of droplets deformed and attracted each other immediately before the coalescence. Through image processing, the radii of curvature of the droplets were quantified and the pressure difference between the inside and outside the droplet was simulated to obtain the pressure and velocity information on the droplet surface. The results revealed that the sound pressure acting on the droplet clearly decreased before the impact of the droplets. This pressure on the droplets was quantitatively analyzed from the experimental data. Our experimental and numerical results provide deeper physical insights into contactless droplet manipulation for futuristic lab-on-a-drop applications.

This study investigated the effects of two plyometric training protocols on sprint and change of direction (COD) performance in elite hockey players. A parallel-group randomized controlled trial design was used and seventeen elite male and female field hockey players were randomly allocated into either low-to-high (L-H, n = 8) or high-to-low (H-L, n = 9) training groups. Each group performed separate variations of the drop jump exercise twice weekly for six weeks, with an emphasis on either jump height (L-H) or drop height (H-L). Performance variables assessed included sprint times over 10 m and 20 m, as well as 505 time. A two-way repeated measures analysis of variance was performed and Cohen’s d effect sizes were calculated. The H-L group displayed significant small ES improvement from baseline to post-training in the 10 m sprint (1.893 ± 0.08 s pre vs 1.851 ± 0.06 s post) (ES = −0.44) (P = <0.05). Small but not statistically significant differences between groups were observed for 10 m and 20 m sprint performance, and no significant differences were observed within or between groups for 505 time. These findings highlight the difficulty in substantially enhancing speed and COD ability in highly trained athletic populations through the addition of a low volume, short duration plyometric training protocol.

Impact characterization of linear resonant actuator (LRA) is studied experimentally by newly developed drop tester, which can control various experimental uncertainty such as rotational moment, air resistance, secondary impact and so on. The feasibility of this test apparatus was verified by comparison with free fall test. By utilizing a high-speed camera and measuring the vibrational displacement of spring material, the impact behavior was captured and the damping ratio of the system was defined. Based on the above processes, the finite element model was established and the experimental and analytical results were successfully correlated. Finally, the damage of the system from impact loading can be expected by developed model and as a result, this research can improve the impact reliability of LRA.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

The superficial quality of the strip is a very important issue in steel production; the profile, flat-ness, and geometry of strip are indicators of supreme quality. Considering the dimensions, the thickness is one of the most important variables in the production of strip. In the present study the elastic curve of Back Up Rolls (BUR) is analyzed, considering them as simply supported beams as well as the effect of rolls on the profile of the strip, specifically in the strip edge pro-ducing edge drop. The analysis is simulated with a model in 3D using a Finite Element Method (FEM) considering +0.039mm crown on Back Up Roll and +0.101mm crown on Work Roll (WR). The results showed that there is an instability zone of 76mm in the strip edge, this geometry is symmetrical in both ends of the strip, it was validated with the results of compact X-ray thick-ness gauge from a 4-high cold mill. This study not only provides a theoretical basis for the edge drop, but also provides the basis for the understanding of deformation on rolls used in rolling mill processes and their effect on the thickness, profile, shape, and dimensional quality of strips.

In this study, the focus is on the drop test simulation of an MR (Magnetorheological) damper-based main landing gear (MRMLG), aiming to explore multi-degree-of-freedom (DOF) dynamic models during aircraft landing. Three different 6-DOF dynamic models are proposed in this work and their drop performances are compared with results achieved one of commercial softwares. The proposed models include a nonlinear aircraft model (NLAM), a linearized approximated aircraft model (LAAM) linearizing from the nonlinear equations of motion in NLAM, and a fully approximated aircraft model (FAAM) which linearizes the MRMLG's strut force model. In order to evaluate drop performance of the aircraft landing gear system with MR dampers, a 7-DOF aircraft model incorporating the nonlinear MRMLG is formulated using RecurDyn. The principal comparative param-eters are the coefficient of determination (R2) for system response of each model with Re-curDyn model and root mean square error (RMSE) which is the ensembles of CG dis-placement data for each model. In addition, the ensemble of time series data is created for diverse drop scenarios, providing valuable insights into the performance of the proposed drop test models of the aircraft landing gear system featuring MR dampers.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.

Road markings play an important role in road safety because they provide significant information to drivers about the road. For that reason, they must be replaced when they are not correctly perceived by road users. To analyse which are the main factors that affect road marking perception over time, a test section was designed in a two-lane rural highway, running actual traffic over 18 different types of markings fabricated with different combinations of drop-on materials. Chromatic coordinates, luminance and retroreflectivity of each sample were measured during 18 months in order to study their evolution over time. The results obtained show different behaviours depending on the aggregates and application method used. An increment of the durability has been observed with the use of different layers and mixtures of glass microbeads with different sizes.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

Diffusion-controlled cyclic voltammograms at fast scan rates show peak shifts as well as decreases in the peak currents from the predicted diffusion-controlled currents especially when currents are large in low concentration of supporting electrolyte. This has been conventionally recognized as an IR-drop effect by solution resistance on the peaks as well as heterogeneous kinetics. It is also brought about by negatively capacitive currents associated with charge transfer reactions. The reaction product generates dipoles with counterions to yield a capacitance, of which current flows oppositely to that of the double layer capacitance. The three effects are specified here in the oxidation of a ferrocenyl derivative by fast scan voltammetry. The expression for voltammograms complicated with IR-drop is derived analytically, and yields deformed voltammograms. The peak shift is approximately linear with the IR-term, but exhibits a convex variation. Dependence of some parameters on the peaks by the IR-drop is compared with those by the negative capacitance. The latter is more conspicuous than the former under conventional conditions. The two effects cannot be distinguished specifically except for variations of conductance of the solution.

There is need to accurately design pipelines to transport the expected increase of CO₂ captured from industrial processes after the signing of the Paris Climate Agreement in 2016. This paper reviews several aspects of CO₂ pipeline design with emphasis on pressure drop and models for the calculation of pipeline diameter. Two categories of pipeline equations were identified. The first category is independent of pipeline length and has two different equations. This category is used to specify adequate pipeline diameter for the volume of fluid transported. The optimum economic pipe diameter equation (Eq. 17) with nearly uniform resultant velocity values at different flow rates performed better than the standard velocity flow equation (Eq. 20). The second category has four different equations and is used to calculate pipeline pressure drop or pipeline distance for the installation of booster stations after specifying minimum and maximum pipeline pressures. The hydraulic equation is preferred because it gave better resultant velocity values and the closest diameter value obtained using Aspen HYSYS (V.10) simulation. The effect of impurities on the pressure behaviour and optimal pipeline diameter and pressure loss due to acceleration were ignored in the development of the models. Further work is ongoing to incorporate these effects into the models.

The purpose of this study is to investigate the impact of the voltage drop of a three-phase voltage source inverter in driving brushless motors. This study also proposes an enhanced Field Oriented Control scheme that accounts for the inverter voltage drop enabling efficient drive at very low motor-speeds. Experimental results are provided to verify the theoretical study and the proposed control scheme.

In a power plant that uses seawater as a coolant, a debris filter is required to remove foreign substances from the seawater, and differential pressure leads to a decrease in the coolant flow rate, leading to a decrease in power generation efficiency. In this study, analysis was performed under different initial flow velocity conditions of 1.5m/s, 2.0m/s, and 2.5m/s for a debris filter used in a power plant to understand flow characteristics in CTCS. The flow and differential pressure characteristics of a CTCS with an installed debris filter were considered in a comparative analysis of velocity, pressure, and turbulent kinetic energy distribution. The results confirmed that a vortex was generated in the pipe with the debris filter, apparently due to the collision of the flow with the bracket of the debris filter. As the flow rate increased, the range of the vortex increased, causing a loss in flow.

Recent improvements within the fields of high-throughput screening and 3D tissue culture have provided the possibility of developing in vitro micro-tissue models that can be used to study diseases and screen potential new therapies. This paper reports a proof of concept study on the use of microvalve-based bioprinting to create laminar MSC-chondrocyte co-cultures as an in vitro model of autologous chondrocyte implantation (ACI), an established cellular therapy for osteoarthritis. Microvalve-based bioprinting uses microvalves to deposit cells suspended in a liquid in a consistent and repeatable manner. In this case MSCs and chondrocytes have been sequentially deposited into an insert based transwell system in order to create a laminar co-culture, with variations in the ratios of the cell types used to investigate the potential for MSCs to stimulate improved repair. Histological and indirect immunofluorescence staining revealed the formation of dense tissue structures within the chondrocyte and MSC-chondrocyte cell co-cultures, alongside the establishment of a proliferative region at the base of the tissue. No stimulatory or inhibitory effect in terms of ECM production was observed through the introduction of MSCs, although the potential for an immunomodulatory benefit remains. This proof-of-concept study therefore provides a novel method to enable the scalable production of therapeutically relevant micro-tissue models that can be used for in vitro research to optimise ACI procedures.

In this study, the values of the interfacial energies of seven different polymer-water systems obtained by Sessile Drop Accelerometry (SDACC) are compared with the values obtained by the Young’s-equation-based Owens-Wendt method. The SDACC laboratory instrument –a combination of a drop shape analyzer with high-speed camera and a microgravity tower- and the evaluation algorithms, are designed to measure the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on Thermodynamics of Interfaces and differs from the conventional aproach of the two hundred-years-old Young’s equation in that it assumes a thermodynamic equilibrium between interfaces, rather than a balance of forces on a point of the solid-liquid-gas contour line. A comparison of the mathematical model that supports the SDACC method with the widely accepted Young`s equation is discussed in detail in this study.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

Background &amp; Aim: Drug sustainability (DS) is a surrogate marker for treatment efficacy. We aimed to compare the DS of two main biologics used to treat moderate-to-severe ulcerative colitis (UC), infliximab (IFX) and vedolizumab (VDZ), in a real-world setting. Methods: We conducted a retrospective cohort study at a tertiary medical center in Israel. We included patients treated between Dec 1st, 2017, and May 1st, 2021, who were followed for up to 300 weeks. DS was defined as corticosteroid, surgical, and hospitalization-free treatment. Results: 217 patients with UC were included. VDZ had a significantly longer median DS of 265.6 weeks compared to IFX's 106.5 weeks (p=0.001) in treatment-naïve patients, even when adjusting for disease severity (HR 0.55 95 CI 0.3-0.98, p=0.042). In treatment-experienced patients, DS was comparable between IFX and VDZ (p=0.593). Conclusion: VDZ showed significantly longer DS in treatment-naïve patients with UC compared to IFX, also when adjusted for disease severity. There was no difference in DS between VDZ and IFX in treatment-experienced patients and patients switching from one drug to another. VDZ may be a suitable first-line treatment for biologic-naïve patients with moderate-to-severe UC.

Background: Cancer has been one of the most critical health problems during the past decades which require serious consideration, especially in developing countries. Methods: 80 parents of the children with different types of cancers were studied via both questionnaire and person-to-person interview after announcing their informed consent. Results: The highest delay in patients' initial referral was due to the following factors: lack of attention or ignoring the first symptoms, delay in referring to the physician, low economic status and even lack of family support for the patient. In addition, visiting several doctors after the initial diagnosis, uncertainty about the first proposed method, and high cost of treatment can be mentioned as the main causes of delays in the start of treatment. Conclusion: Education plays an important role in identifying the signs of cancer. In addition, proper relationship and cooperation between the health system and physicians as well as provision of adequate information to patients could lead to the long-term cooperation of these patients in continuing their treatment.

This work presents a design and model of the thermo-hydrodynamic behavior applying CFD for pin-fin heat sink with square shape (rectangular fin profile), through a novel pin arrangement that improves heat removal in the system. The novelty consist in the insertion of a deflector row that will help to direct the flow, so it hits the rectangular cross-sectional fins the presents in the system. The heat sink model is placed in channel designed in which air flows as suitable medium, and its overall performance is investigated. In addition, a constant heat flux is applied to the bottom wall of the heat sink model, equal values and amounts that​ correspond to the heat fluxes generated by current electronic equipment and devices. The numerical results of the global thermal resistance, the pressure drop and the Nusselt number are reported. The results allow determining best arrangement or geometry configuration, location and functionality of the fin-deflectors were collocated for evaluate thermal-hydraulic efficiency of system.

Current article presents the study of psychological wellbeing of adolescents (n=168, age 15-17) gifted in math, humanities and sports and educated in advanced programs for gifted children. Theoretical framework of this study is eudemonic concept of psychological wellbeing by C. Ryff. Psychological wellbeing is measured with Ryff wellbeing scales in Russian adaptation by L.V. Zhukovskaya and E.G. Troshikhina. The study is aimed at understanding differences in psychological wellbeing of gifted teenagers connected to gender and type of giftedness. The results suggest that general wellbeing score did not differ for adolescents with different types of giftedness or of different genders. Separate components of psychological wellbeing, such as purpose in life and self-acceptance, are influenced by activity connected to the talent. Gender differences are subjected to age-specific trends of personal development in adolescence. Type of giftedness might reinforce these trends.

With Internet of Things (IoT) gaining presence throughout different industries a lot of new technologies have been introduced to support this undertaking. Implications on one such technology, wireless systems allowed for the use of different communication methods to achieve the goal of transferring data reliably, with more cost efficiency and over longer distances. Anywhere from a single house with only a few IoT devices such as a smart light bulb or a smart thermostat connected to the network, all the way to a complex system that can control power grids throughout countries, IoT has been becoming a necessity in everyday lives. This paper presents an overview of the devices, systems and wireless technologies used in different IoT architectures (Healthcare, Vehicular Networks, Mining, Learning, Energy, Smart Cities, Behaviors and Decision Making), their upbringings and challenges to this date and some foreseen in the future.

The numerous biological activities of phenothiazine and sulphonamide derivatives, especially their antibacterial qualities, have attracted so much interest. In this study, the synthesis and characterization of phenothiazine-3-sulphonamide derivatives and evaluation their antimicrobial activity against the following pathogenic microorganisms is reported. Two gram-positive bacteria; (Staphylococcus aureus, and Streptococcus pyogenes), two gram-negative bacteria; (Escherichia coli, and Salmonella typhi) as well as one fungus (Aspergillus fumigatus) were used while ciprofloxacin, gentamycin and ketoconazole served as standard drugs. The synthesis of the derivatives was achieved through a base catalyzed the reaction of 4-chloroaniline with 1-naphthylamine to form 1-(naphthalen-1-yl) benzene-1,4-diamine. This intermediate was then treated with sulphur and iodine to yield the phenothiazine derivative while subsequent treatment of the phenothiazine compound with sulphonyl chlorides gave the final products. The synthesized compounds were characterized via proton nuclear magnetic resonance (1HNMR), carbon-13 nuclear magnetic resonance (13C NMR) and Fourier-transform infrared (FTIR) spectroscopic techniques. The minimum inhibitory concentration (MIC) of each compound was then determined using the agar well diffusion method. To predict the binding energies and patterns of the synthesized compounds with target proteins of the above mentioned microorganisms, molecular docking simulations were run using Autodock Vina software (version 4.2). The spectra data of the compounds for FTIR, 1H NMR and 13C NMR (δ) spectral data were consistent with the assigned structures of the synthesized compounds. The binding energies (kcal/mol) for in silico antimicrobial studies were in the range -5.1 to -7.6 kcal/mol. The MIC values were in the range -3.5 to 1.0 mg/L. The results of the in vitro test revealed that the synthesized compounds exhibits promising antimicrobial activity, and showed excellent bactericidal and fungicidal activities. The results obtained showed that the synthesized compounds possess drug-like properties and are good starting materials for drug production.

Background: Redo mitral valve surgery is the standard of care for failed mitral bioprostheses or recurrence of mitral regurgitation after repair. Nonetheless, catheterbased valve-in-valve (ViV) or valve-in-ring (ViR)-procedures increasingly become viable alternatives in high risk subpopula-tions. Despite reported good initial results, only little is known about longer-term outcomes. The present series report long-term outcomes of transcatheter mitral ViV- and ViR-procedures. Methods: All consecutive patients (n=54) undergoing transcatheter mitral ViV- or ViR-procedures for failed bioprostheses or recurring regurgitation after mitral repair were retrospectively en-rolled in the time period between 2011 and 2021. The mean age was 76.5 ± 6.5 years, and 30 (55.6%) of the patients were male. The procedures were done using a commercially available balloon-expandable transcatheter heart valve. Clinical and echocardiographic follow-up data were obtained out of the hospital’s database and analyzed. Follow-up reached up to 9.9 years with a total of 164.3 patient-years. Results: A total 25 patients received a ViV- and 29 patients a ViR-procedure. Both groups were at high surgical risk with an STS-PROM of 5.9 ± 3.7 % in ViV- and 8.7 ± 9.0% in ViR-patients, respectively (p<0.01). The procedures itself were mainly unevent-ful with no intraoperative deaths and a low conversion rate (n=2/54; 3.7%). VARC-2 procedural success was low (ViV 20.0% and ViR 10.3%; p=0.45), which was either driven by high rates of transvalvular pressure gradients “>5mmHg” (ViV 92.0% and ViR 27.6%; p<0.01) or residual regurgitation “>trace” (ViV 28.0% and ViR 82.7%; p<0.01). ICU-stay was prolonged in both groups (ViV 3.8 ± 6.8 days and ViR 4.3 ± 6.3 days; p=0.96) with acceptable hospital stay (ViV 9.9 ± 5.9 days and ViR 13.5 ± 8.0 days; p=0.13). Despite 30-days mortality was acceptable (ViV 4.0% and ViR 6.9%; p=1.00), the mean posthospital survival time was disappointingly low (ViV 3.9 ± 2.6 years and ViR 2.3 ± 2.7 years; p<0.01). Overall survival I the entire group was 33.3%.Cardiac reasons for death were frequent in both groups (ViV 38.5% and ViR 52.2%). Cox-regression analysis identified ViR-procedures as a predictor of mortality (HR 2.36, CI 1.19 - 4.67, p=0.01). Conclusions: Despite acceptable immediate outcomes in this high-risk subpopulation, long-terms results are discouraging. Transvalvular pressure gradients as well as residual regurgitations remained drawbacks in this real-world population. The indication for catheterbased mitral ViV- or ViR-procedures thoughtfully must be made in consideration of conventional redo-surgery or conservative treatment.

In an effort to discover an effective and selective antitumour agent, synthesis and anti-cancer potential of 4-(pyridin-4-yl)-6-(thiophen-2-yl)pyrimidin-2(1H)-one (SK-25), which has been reported earlier by us with significant cytotoxicity towards MiaPaCa-2 malignant cells, with an IC₅₀ value of 1.95 μM and was found to instigate apoptosis. In the present study, the antitumour efficacy of SK-25 was investigated on Ehrlich ascites tumour (solid), Sarcoma 180 (solid) tumour and Ehrlich ascites carcinoma. The compound was found to inhibit tumour development by 94.71% in Ehrlich ascites carcinoma (EAC), 59.06% in Ehrlich tumour (ET, solid) and 45.68% in Sarcoma-180 (solid) at 30 mg/kg dose. Additionally, SK-25 was established to be non-toxic at a maximum tolerated dose of 1000 mg/kg in acute oral toxicity in Swiss-albino mice. Computer-based predictions also show that the compounds could have an interesting DMPK profile. The current study provides insight for further investigation of the antitumour potential of the molecule.

In this paper, we discuss major issues of mathematics teaching and learning in Nepal. The issues coming from theories such as social and radical constructivism suggest that teachers are not trained to use such approach in teaching mathematics, and there is a lack of teaching aids and materials and technological tools. The issues related to social aspects are gender issues, language issues, social justice issues, and issues related to the achievement gap. The cultural issues are related to the diversity of language and ethnicity. The issues related to political aspects are equity and access, economic status, pedagogical choice, and professional organizations and unions. The issues related to technology include the technological skills, use of technology, and affordance. Finally, we suggest that all the stakeholders should pay attention to resolving these issues by improving the curriculum, training teachers, resourcing the classroom with locally made and new technological tools.

Physics behind collimated highly directional nature of lasers, and factors that keep the seven coloured waves that form white light together during their journey from Sun to Earth, in the face of the natural disruptive forces, is not fully understood. Energy levels were measured, in terms of alterations in induced current and voltage, in beams from a red laser, white LED light and the Sunlight before and during their disruption by diffusers (frosted glass for the lasers) and diffractors (diffraction grating for the white light) using a photovoltaic solar cell panel attached to a digital multimeter. Results show that disruption of the beams results in release of extra energy named as ‘Latent Light Binding’ Energy’. It is hypothesized that the ‘binding’ energy keeps laser waves firmly bound together both end-on and side-on enabling laser beams to travel long distances in collimated manner. Likewise, the 7 coloured waves that constitute white light are kept together, probably side-on, in their journey from the Sun to the Earth. The observation that diffraction of sunbeam is associated with increased power generation provides a new lead to improve harnessing of solar energy, where, currently, the focus is mainly on improving efficiency of photovoltaic cell.

Piceatannol is a naturally occurring polyphenolic compound that is widely found in grapes, blueberries, mushrooms, passion fruit and other edible fruits and vegetables. It has a variety of biological activities and pharmacological effects, including anti-inflammatory, antioxidation, antiaging, antiviral, antitumor, anticancer, antiatherosclerosis, antiparasitic, immunoregulatory, and cardiovascular protection effects. The aim of this study was to investigate the antiherpesvirus effects of piceatannol. Pseudorabies virus (PRV) belongs to the family Herpesviridae. PRV has a wide host range and can cause cytopathic effects (CPEs) in PK-15 cells. Therefore, PRV was used as a model to study the antiherpesvirus effect of piceatannol. In this study, we evaluated the antiviral activity of piceatannol against PRV in vitro and in vivo. The results showed that piceatannol could reatrain PRV multiplication in PK-15 cells in a dose-dependent manner. The 50% inhibitory concentration (IC50) was 0.0307 mg/mL, the IC50 was 0.0307 mg/mL, and the selectivity index (SI, CC50/IC50) was 3.68. The addition of piceatannol at different stages of PRV infection inhibited the viral adsorption and intracellular replication phases of PRV. Piceatannol significantly reduced the expression levels of the IE180, EP0, UL29, UL44, US6 and UL27 genes of PRV within 48 h, significantly reduced the expression levels of the PRV gB and gD proteins, and reduced PRV-induced apoptosis. Molecular docking showed that piceatannol had good binding activity with the PRV gB and gD proteins. The results of animal experiments in vitro indicated that piceatannol could delay the onset of disease, improve the survival rate of the mice (14.3%), reduce the viral load in the brain and kidney of the mice, alleviate the pathological changes in the mouse tissues and organs, and increase the levels of TNF-α, IEN-γ and IL-4 in the serum of the mice. These data indicate that piceatannol has good anti-PRV activity in vitro and in vivo, indicating that it could be a novel antiherpesvirus infection agent in the future.

Diabetes mellitus is a global health issue that necessitates the development of novel therapeutic approaches. Today numerous experimental methods have been used and set up to evaluate novel drugs with antidiabetic effects. In addition, several research studies have been done to induce diabetes under in vitro and in vivo conditions, but only a small number of these efforts are currently in a usable stage. This review aims to provide useful guidance for researchers who seek to evaluate the antidiabetic potential of drugs, agents, or new medications using the standard methods published by authorities and academics worldwide organizations and research centers. In this review, we collected 132 relevant articles from prominent databases such as PubMed, ScienceDirect, Scopus and others to summarize in vitro and in vivo experimental validation of antidiabetic treatment from 1943 to present.

Leishmaniasis is a vector-borne parasitic infection caused by the bite of female Phlebotomine sandflies. World Health Organization (WHO) estimates 100,000 cases to be reported annually on a global scale, moreover, 13 million people were infected between 2010 and 2015 worldwide. Treatment of leishmaniasis by conventional synthetic compounds is met by challenges pertaining to adverse effects which call for the discovery of newer anti-leishmanial molecules. This study was performed to evaluate the effect and modes of action of a sesquiterpene alcoholic molecule Farnesol on Leishmania major, the causative agent of Zoonotic Cutaneous leishmaniasis. The cytotoxic effect of Farnesol against L. major promastigotes, amastigotes and macrophages was assessed by MTT test and counting. The IC50 on promastigotes by Farnesol on L. major was evaluated by flow cytometry. In the findings, Promastigotes were reduced at 167 µM/mL & the mean numbers of L. major amastigotes in macrophages were significantly decreased in exposure to Farnesol at 172 µM/ml. In addition, Farnesol demonstrated no cytotoxicity on macrophages as the IC50 value was 945 µM/ml; it induced significant apoptosis dose-dependent on L. major promastigotes. In silico protein-ligand binding analyses indicated the effect of Farnesol in perturbation of the ergosterol synthesis pathway of Leishmania with attributes suggesting inhibition of Lanosterol-α-demethylase, the terminal enzyme of ergosterol synthesis machinery. Findings from flow cytometry reveal the role of farnesol in apoptosis-induced killing in promastigotes. Farnesol was effective at very lower concentrations when compared to Paromomycin. Further studies are crucial to evaluate the therapeutic potentials of Farnesol alone and in combination with other conventional drugs using clinical settings.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Heat enhancement is a topic of great interest nowadays due to its different application in industries. Porous material also known as metallic foam plays a major role in heat enhancement at the expenses of pressure drop. Flow in channels demonstrate the usefulness of this technology in heat extraction. In our current study, a porous strip attached to the channels walls is proposed as an alternative for heat enhancement. The thickness of the porous strip was varied for different Reynolds number. By maintaining laminar regime and using water as fluid, we determined an optimum thickness of porous material leading to the highest performance evaluation criterion. In our current study with the aspect ratio being the porous strip thickness over the channel width, an aspect ratio of 0.2 is found to be the alternative. A 40% increase in heat enhancement is detected in the presence of porous strip when compared to a clear channel case for a Reynolds number equal to 200 and improve further as the Reynolds number increase accordingly.

This article explores the relationship between convex functions defined on integers ($\mathbb{Z}$) and their extension to real numbers ($\mathbb{R}$). We introduce key definitions and investigate the hypothesis that there exists a unique convex curve within this family of functions, leading to a proof by contradiction. Our findings highlight the preservation of convexity as functions transition from integers to real numbers.

Among the alternatives pointed out as able to make livestock a more efficient activity and reduce its environmental impact, the use of feeds with high digestibility and the use of non-conventional fodder species can be highlighted. Tithonia diversifolia (Hemsl.) A. Gray (TD) has already gained attention as a feed for ruminants. Nonetheless, there has been little discussion about the impacts of this plant on the rumen dynamics that lead to better animal performance. The aim of this study was to assess how increasing levels of TD could affect ruminal microbial biomass synthesis, degradability, and in vitro gas production (IVGP) of diets. Four diets were evaluated: a control diet (TD0: 400 g kg-1 soybean meal and corn grain, and 600 g kg-1 Tifton 85 hay (Cynodon spp)) and three increasing levels of TD (TD9: 90, TD27: 270, and TD45: 450 g kg-1 – dry matter basis) as a replacement for dietary roughage. A 96-hour IVGP assay was carried out and five incubation times (2, 4, 10, 24, and 96 hours) were used for degradability determination. Gas produced, methane (CH4), degradability of organic matter (IVDOM), short-chained fatty acid (SCFA) production, partitioning factor (PF), and microbial biomass (MB) were evaluated among treatments. There was no significant effect (P&gt;0.05) between TD inclusion and IVGP at most incubation times; only at 6 hours of incubation did gas production increase linearly with TD inclusion (R2=0.19; P&lt;0.05). TD inclusion had no effects on CH4. IVDOM increased linearly with TD inclusion at 6 and 10 hours, with TD45 being more degradable than the control diet at 6 hours only. There was a positive linear relationship (R2=0.20; P&lt;0.05) between TD inclusion and PF. TD45 had significantly higher PF values than the control. MB also increased linearly (R2=0.30; P&lt;0.05) with TD inclusion, and all diets with TD had significantly more MB than the control diet. The inclusion of TD at the levels used in this work was revealed to have a positive impact on microbial protein synthesis, which could be related to the higher microbial efficiency of increased substrate quality.

Oxalate, a compound produced by many edible plants and as a terminal metabolite in the liver of mammals, is a toxin that has a detrimental role to human health. Humans and other mam-mals do produce the enzymatic machinery to degrade oxalate. However, numerous oxa-late-degrading bacteria reside in the mammalian gut and thus provide an important function for hosts. The current review focuses on the environmental factors that influence the efficacy of pro-biotic oxalate-degrading bacteria, relative to oxalate metabolism. We describe the mechanism of oxalate catabolism and its consumption by obligate and facultative anaerobic oxalate-degrading bacteria, in both in vitro and in vivo environments. We also explore the environmental variables that impact oxalate degradation. Studies on single species degrade oxalate have not shown a strong impact on oxalate metabolism especially in high oxalate conditions such as consumption of foods high in oxalate (such as coffee and chocolate for humans or halogeton in animal feed). Considering effective variables which enhance oxalate degradation could be used in application of effective probiotic as a therapeutic tool in individuals with hyperoxaluria. This study indicates probiotics can be considered a good source of naturally occurring oxalate degrading agent in human colon

The World Anti-Doping Agency has prohibited gene doping in the context of progress in gene therapy. There is a risk that the artificial regulation of genes using plasmids could be applied for gene doping. However, no gold standard method to detect this has been established. Here, we aimed to develop a method to detect multiple transgene fragments as proof of gene doping. First, gene delivery model mice as a mimic of gene doping were created by injecting firefly luciferase plasmid with polyethylenimine (PEI) into the abdominal cavity. The results confirmed successful establishment of the model, with sufficient luminescence upon in vivo imaging. Next, multiple transgene fragments in the model were detected in plasma cell-free (cf)DNA, blood-cell-fraction DNA, and stool DNA using the TaqMan-qPCR assay, with the highest levels in plasma cfDNA. Using just a single drop of whole blood from the model, we also attempted long-term detection. The results showed that multiple transgene fragments were detected until 11 days. These findings indicate that the combination of plasma cfDNA or just one drop of whole blood with TaqMan-qPCR assay is feasible to detect plasmid-PEI-based gene doping. Our findings could accelerate the development of methods for detecting gene doping in humans.

The screen-printed carbon nanofibers electrodes (SPCNFE) represent an alternative with great acceptance due to their results, as well as their low impact for the environment. In order to improve their performance, in the present work they were modified with silver nanoparticles (Ag-NPs) and electrochemically characterized by using anodic stripping voltammetry. From the Ag-NPs synthesis, silver seeds (Ag-NS) and silver nanoprisms (Ag-NPr) were obtained. The Ag-NPs formation was confirmed by micrographs where Ag-NPs with diameters of 12.20±0.04 nm for Ag-NS, and 20.40±0.09 nm for Ag-NPr were observed. The electrodes were modified by using three different deposition methods: drop-casting, spin-coating and in-situ approaches. It was observed that the last methodology showed a low amount of Ag-NS deposited on the electrode surface and a deep alteration of this surface. Those facts suggested that the in situ synthesis methodology were not appropriate for the determination of heavy metals and it was discarded. The incorporation of the nanoparticles by spin-coating and drop-casting strategies showed different spatial distribution on the electrode surface as proved by scanning electron microscopy. The electrodes modified by these strategies, were evaluated for the cadmium(II) and lead(II) detection using differential pulse anodic stripping voltammetry, obtaining detection limit values of 2.1 and 2.8 µg L^-1, respectively. The overall results showed that the incorporation route does not change directly the electrocatalytic effect of the nanoparticles, but the shape of these nanoparticles (spherical for seeds and triangular for prisms) has a preferential electrocatalytical enhancement over Cd(II) or Pb(II).

The article presents the results of tests of minor head losses through PVC and PP elbows for a flow of water and mixtures of water and sand with grain sizes of up to 0.5 mm and concentrations of 5.6 g∙L-1, 10.84 g∙L-1, and 15.73 g∙L-1. The tests were carried out at variable flow velocities for three elbow diameters of 63, 75, and 90 mm. The flow rate, pressure difference in the tested cross-sections, and temperature of the fluids were measured and automatically recorded. The results of the measurements were used to develop mathematical models for determining the minor head loss coefficient as a function of elbow diameter, sand concentration in the liquid, and Reynolds number. The mathematical model was developed by cross validation. It was shown that when the concentration of sand in the liquid was increased by 1.0 g∙L-1, the coefficient of minor head loss through the elbows increased, in the Reynolds number range of 4.6∙104 − 2.1∙105, by 0.3−0.01% for PP63, 0.6−0.03 % for PP75, 1.1−0.06 % for PP90, 0.8−0.01 % for PVC63, 0.8−0.02 % for PVC75, and 0.9−0.04 % for PVC90. An increase in Re from 5∙104 to 2∙106 for elbows with diameters of 63, 75 and 90 mm caused a 7.3 %, 6.8 %, and 6.0 % decrease in the minor head loss coefficient, respectively.

The aim of this study is to emphasize on the clinical uses of amniotic membrane (AM) in multiple ocular disorders. AM possesses many properties including promotion of epithelialization, anti-fibrotic, anti-apoptotic, anti-angiogenic properties. Epithelial wound healing on the eye surface is promoted due to several epidermal and keratocyte growth factors as well as by its anti-inflammatory and anti-scarring effects due to interleukin-10, interleukin-1 receptor antagonists and inhibition of transforming growth factor- beta (TGF-β) signal transduction by AM in the corneal and conjunctival fibroblasts respectively. It plays a crucial role by functioning as a substitute of basement membrane (BM) and as a temporary graft material. It is not only being used as an eye graft but also its extract can be used as an eye drop for corneal and external eye diseases. So its proper preparation, preservation and clinical application can bring a revolutionary change in the treatment of different ocular disorders.

Bioactive fractions were isolated from the leaves extract of Kalanchoe pinnata and subjected to scrutiny for their prospective anti-obesity properties. An array of in vitro phytochemical, antioxidant, and enzyme inhibition assays were executed, which dis-cerned fractions F1 and F2 as the most effective fractions. These fractions were sub-sequently studied through in vivo experiments, affirming that F2 as the most potent fraction. Further characterization of F2 was conducted via HPTLC MS-MSn tech-niques. The outcomes demonstrated that F2 produced a notable anti-obesity effect in obese mice, reducing their body weight and lipid metrics, and leading to advanta-geous changes in their organs. An analytical examination of F2 revealed the existence of four principal compounds, which were subsequently subjected to in silco molecular docking and dynamic analysis, confirming their aptitude for binding to selected pro-teins. These findings imply that the utilization of Kalanchoe pinnata leaves could pro-vide a promising therapeutic strategy for the treatment of obesity.

Analysing the human body by direct observation can lead to misinterpretation of underlying trends, whereas in vitro organ models facilitate their understanding. Likewise, in vitro organ models serve as valuable tools for assessing the toxicity of compounds. However, none of the existing models had the features we considered critical for toxicity assessment, so we developed an in vitro liver model for toxicity assessment. We used four different types of primary liver cells: Hepatic sinusoidal endothelial cells, hepatic stellate cells, Kupffer cells and hepatocytes. We cultured them in different combinations of composition and volume of cell medium, hepatocyte proportion of total cells, and addition of extracellular matrix. We added rifampicin, ibuprofen and 5-fluorouracil to this model and observed the microanatomy and physiology changes for a week with preclinical and clinical instruments. Among the different model configurations, we selected the feature combination of the in vitro model that had similar biomarker values to those measured by the clinical instruments used in clinical diagnostics. When we exposed the selected model configuration to rifampicin, ibuprofen and 5-fluorouracil, the viability of Kupffer cells and liver sinusoidal endothelial cells was significantly lower than in the untreated samples. In contrast, we observed negligible viability of hepatocytes compared to the untreated samples. We have built an in vitro liver model that resembles the liver microenvironment and we have analysed it with clinical instrumentation to facilitate the data translation. In this sense, we have established that Kupffer and LSEC cells are suitable candidates for the search for clinical diagnostic markers of liver function.

Knowledge about ecological conditions and processes in centers of endemism (CoEs) is still limited with respect to various systematic groups of organisms, ecosystem types, ecological conditions and ecosystem functions. Endemics and CoEs play a prominent role in nature conservation monitoring and management, and in the organization of zoos, aquaria and botanical gardens. We review the meaning of different groups of organisms and indicators for the characterization of endemic-rich regions, the importance of heterogeneity in space, continuity in time, isolation and ex-situ management for the survival of endemic and threatened species. Currently, conversion of land cover and land use change are the most important causes of biodiversity decline and extinction risk of endemic and endangered species concentrated in CoEs. These are followed by climate change, including severe weather, and then natural processes such as volcanism, landslides or tsunamis. For conservation purposes the management of zoos, aquaria, botanical gardens, of regional land use, and social aspects of the diversity of endemics and CoEs have to be taken into account as well. We need better answers to questions about the relationship between ecoregions, CoEs and regional awareness of biodiversity, which is linked with human culture including the management of zoos, aquaria and botanical gardens, aesthetics, wellbeing, health and trade.

Introduction: The combination of Virtual Screening (VS) techniques with in vivo screening in the zebrafish model is currently being used in tandem for drug development in a faster and more efficient way. Areas covered: We review the different virtual screening techniques, the use of zebrafish as a vertebrate model for drug discovery and the synergy that exists between them. Expert opinion: We highlight the advantages of combining virtual and zebrafish larvae screening for drug discovery. On the one hand, VS is a faster and cheaper tool for searching active compounds and possible candidates for therapy than in vivo screening when processing large compound libraries. On the other hand, zebrafish larvae form a vertebrate model which allows in vivo screening of large amounts of the compounds. Importantly physiology and chemical response are mostly conserved between zebrafish and mammals. The availability of the transgenic and mutant zebrafish lines allows an analysis of a specific phenotype upon treatment along with toxicity, off-target effect, side effects, and dosage. Advantages of VS, in vivo whole animal approach screening, and the screening combinations are also reviewed.

Human eye is a specialized organ with complex anatomy and physiology, because it is characterized by different cell types with specific physiological functions. Given the complexity of the eye, ocular tissues are finely organized and orchestrated. In the last few years many in vitro models have been developed, in order to meet the 3Rs principle (Replacement, Reduction and Refinement) for eye toxicity testing. This procedure is highly necessary to ensure that the risks associated with ophthalmic products meet appropriate safety criteria. In vitro preclinical testing is now a well-established practice of significant importance for evaluating the efficacy and safety of cosmetic, pharmaceutical, and nutraceutical products. Along with in vitro testing, also computational procedures, herein described, for evaluating the pharmacological profile of potential ocular drug candidates including their toxicity, are in rapid expansion. In this review the ocular cell types and functionality are described providing an overview about the scientific challenge for the development of three-dimensional in vitro models.

Abstract: The aim of this study is to emphasize on the clinical uses of amniotic membrane (AM) in multiple ocular disorders. AM possesses many properties including promotion of epithelialization, anti-fibrotic, anti-apoptotic, anti-angiogenic properties. Epithelial wound healing on the eye surface is promoted due to several epidermal and keratocyte growth factors as well as by its anti-inflammatory and anti-scarring effects due to interleukin-10, interleukin-1 receptor antagonists and inhibition of transforming growth factor- beta (TGF-β) signal transduction by AM in the corneal and conjunctival fibroblasts respectively. It plays a crucial role by functioning as a substitute of basement membrane (BM) and as a temporary graft material. It is not only being used as an eye graft but also its extract can be used as an eye drop for corneal and external eye diseases. So its proper preparation, preservation and clinical application can bring a revolutionary change in the treatment of different ocular disorders.

This comprehensive study delves into the implementation and effectiveness of the flipped classroom model in engineering EMI (English as a Medium of Instruction) courses in Taiwan. Situated within the strategic framework of Taiwan's Bilingual Nation 2023 policy, this research aims to enhance the global competitiveness of Taiwan's semiconducting manufacturing engineering sector. The study’s primary focus is on understanding the perceptions and learning outcomes of EFL (English as a Foreign Language) students in engineering courses. Through a methodical approach using descriptive statistics and chi-square tests, the study analyzes data from 33 junior engineering students specializing in mechanical and mechatronic fields. The findings highlight a significant positive influence of the flipped classroom model on various aspects of student learning, including increased engagement, heightened creativity, and enhanced problem-solving skills. Additionally, the study emphasizes the critical role of timely L1 support in facilitating effective learning in EMI settings. These outcomes not only demonstrate the flipped classroom's viability as a sustainable educational approach but also provide crucial insights for educators and policymakers. By aligning cutting-edge teaching methods with the evolving needs of engineering education, this study contributes to the discourse on educational innovation. It ultimately guides the development of future engineering programs that cater to diverse student needs and fosters the cultivation of skilled engineering professionals.

This study was to designed to develop sorafenib-loaded polymeric nanoparticles, surface-modified with pluronic F-127 for the effective treatment of hepatocellular (HCC) and renal cell carcinomas (RCC). Poly lactic coglycolic acid (PLGA) was used to encapsulate different concentrations of sorafenib by a simple modified solvent evaporation method applying pluronic F-127 as a surfactant and coating agent. The preformulation and characterization studies were conducted to evaluate the incompatibilities among sorafenib, PLGA and pluronic F-127, and physicochemical properties of the formulations, respectively. The sizes of the coated and plain PLGA nanoparticles were ~140 ± 14.7 nm and ~ 120 ± 10.1 nm, respectively. It has been confirmed from the in vitro release studies that PLGA sustained the release of sorafenib, avoiding the initial burst release, while the in vivo studies demonstared that surface-modified nanoparticles have greater affinity in the target aorgans than plain PLGA nanoparticles and free drug keeping the dose constant (20 mg/kg body weight). The delivery of sorafenib-loaded polymeric PLGA nanoparticles into the target tissues and their pharmacokinetic parameters have been improved significantly compared to the reported formulations.

The pinning force density FpJc,B=Jc×B (where Jc is the critical current density and B is the applied magnetic field) is one of the main parameters that characterize the resilience of a superconductor to carry a dissipative-free transport current in an applied magnetic field. Kramer (1973 J. Appl. Phys. 44 1360), and Dew-Hughes (1974 Phil. Mag. 30 293) proposed a widely used scaling law for the pinning force density amplitude: FpB=Fp,max×p+qp+qppqq×BBc2p×1-BBc2q, where Fp,max, Bc2, p, and q are free-fitting parameters. Since the late 1970-s till now, several research groups have reported experimental data on the dependence of Fp,max on the average grain size, d, in Nb3Sn-based conductors. Godeke (2006 Supercond. Sci. Techn. 19 R68) proposed that the dependence obeys the law Fp,maxd=A×ln1d+B. However, this scaling law has several problems, for instance, the logarithm is taken from a non-dimensionless variable, and Fp,maxd&lt;0 for large grain sizes, and Fp,maxd→∞ for d→0. Here, we reanalysed the full inventory of publicly available Fp,maxd data for Nb3Sn conductors and found that the dependence can be described by Fp,maxd=Fp,max0×exp-dδ law, where the characteristic length, δ, varies within a remarkably narrow range, that is, δ=175±13 nm, for samples fabricated by different technologies. The interpretation of the result is based on the idea that the in-field supercurrent flows within a thin surface layer (thickness of δ) near the grain boundary surfaces (similar to London’s law, where the self-field supercurrent flows within a thin surface layer with a thickness of the London penetration depth, λ, and the surface is a superconductor-vacuum surface). An alternative interpretation is that δ represents the characteristic length of the exponential decay flux pinning potential from the dominant defects in Nb3Sn superconductors, which are grain boundaries.

The Oxford English Dictionary includes 17 definitions for the word “model” as a noun and other 11 as a verb. Therefore, context is necessary to understand the meaning of the word model. For in-stance, “model railways” refer to replicas of railways and trains at a smaller scale and a “model student” refers to an exemplar individual. In some cases, a specific context, like cancer research, may not be sufficient to provide one specific meaning of a model. Even if the context is narrowed, specifically to the research related to the tumour microenvironment, a “model” can be understood in a wide variety of ways, from an animal model, to a mathematical expression. This paper presents a review of the different “models” of the tumour microenvironment grouped by the different def-initions of the word into four categories: model organisms, in vitro models, mathematical models, and computational models. Then, the frequency of different meanings of the word “model” related to the tumour microenvironment is measured from the number of entries in the MEDLINE database of the United States National Library of Medicine at the National Institutes of Health. The frequency of the main components of the microenvironment and the organ-related cancers modelled are also assessed quantitatively with specific keywords. Whilst animal models, in particular xenografts and mouse models are the most common used “models”, the number of entries have been slowly de-creasing. Mathematical models, prognostic and risk models follow in frequency and these have been growing in use.

In this review we look at the developments in the field of artificial intelligence (A.I) and their current impact as well as future implications in the field of cardiology, we as physicians and cardiologists have tried to put our perspective on the rapidly evolving field, In light of the fact that many of the healthcare workers and professionals across the world still find the concept of A.I quite complicated, elusive and somewhat paradoxical, we have tried to simplify the concept of artificial intelligence and make it easy for everyone to understand from all walks of life. The Databases utilized for our review are PubMed, PubMed Central, Google Scholar. The Keywords used for our Data Search are “Artificial Intelligence”, “A.I Cardiology”, “A.I in Cardiovascular Medicine”, “Machine Learning in Cardiology”. We screened all relevant since inception till March 25th and included 44 relevant articles after careful consideration into our paper. We have discussed the implementation of and scope of artificial intelligence across a broad spectrum of applications including cardiovascular imaging and diagnostics like electrocardiograms, echocardiograms, cardiac CT/MRIs to novel cardiac monitoring devices, CRISPR gene editing in cardiology and implementation of artificial intelligence in the field of Cardiovascular Bioprinting. This is the initial review in a series of reviews regarding A.I in Cardiology.

The Environmental interactions contributed to the processes of settlement and development of the first settlers at southern Peru 15,000 BC. The determination of this process is based on paleoclimatic studies at southern Peru and ethnoarchaeological evidence. The determination of this process is based on paleoclimatic studies of southern Peru and ethnoarchaeological evidence; establishing as a result of this analysis the hypothesis of environmental interaction and territorial occupation of the first hunter-gatherer populations until their consolidation, dominating the geographical space from Tacna. The Disruptive disaster events and their effects on climate during the Peruvian Paleolithic resulted in the origin of local societies that shaped the Tiawanaku societies of the early horizon at Southern Peru and Northern Chile.

This study empirically analyzes the effectiveness of resource optimization utilizing artificial intelligence (AI) within cloud computing environments. It compares systems that have been transitioned from a Monolithic structure to Microservices Architecture (MSA) with those adopting a simple Rehost strategy, to validate the operational efficiency of two systems whose resource efficiency has been enhanced compared to traditional legacy systems. The research is based on systems that determined resource efficiency post-cloud migration using APM tools. It points out the limitations of traditional heuristic operation methods in resource optimization, which lead to issues such as application performance degradation, resource over-allocation, and increased operational costs. This study aims to overcome the conventional resource optimization standards that depended on the average peak usage of CPU and memory infrastructure, by introducing AI-based optimization tools, and applying on-premise standards to cloud and container environments to achieve resource optimization. The paper emphasizes the importance of resource optimization through AI-based automation tools, exploring the possibilities of resolving real-world application performance issues in cloud environments, reducing unnecessary resource usage costs, and cutting down on labor risks and operational expenses. Through this, it presents strategic directions on how AI technology can offer financial and operational advantages in managing cloud resources.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

The effect of the melt cooling rate on the atomic ordering of austenite and, as a consequence, on the martensitic transformation of a nonstoichiometric alloy of the Ni-Mn-In system has been studied. In-situ TEM observations revealed differences in the mechanism of phase transformations of the alloy subjected to different cooling conditions. It is shown that during quenching a high density of antiphase boundaries (APB) is formed and the alloy is in the austenite-martensitic (10M and 14M) state up to a temperature of 120K. In a slowly cooled alloy, a lower APB density is observed, and a two-stage transformation L21/B2 → 10M → 14M occurs in the range of 150–120 K.

Purpose: When it comes to improving citizen service delivery standard and processes, or broadly, management in government (MIG), many reform programs and improvement efforts are ongoing across different ministries, departments, and agencies. This paper is part of a larger empirical research where we are interested to know what those programs and projects are, and how they are doing, and what the gaps are. Design/methodology/approach: Analyzing the publicly available data on the government portal and donors’ website, this article provides an overall idea of current reforms in various places of government. In parallel, field research was conducted through visiting agency offices, observing office environment and mechanisms, and interviewing public managers who are working at district and sub-district level offices of directorates or agencies.Findings: As a trend, state-led development process and the traditional mode of administration have moved to New Public Management based quality and performance approach. All donors have their own strategy framework document like ‘Country Assistance strategy’, ‘Country Operations and Business Plan’, Logical Framework Document, Focus or Priority Streams, etc. Many of the projects are sectoral and agency or ministry specific and have an inherent limitations, due to ‘cadre’ based organizational structural arrangement. So, it is common ‘not to own the projects’, rather ‘using the fund as much as possible anyway within the given project duration’. When the fund ends, implementing units, either government or NGOs, abandon the projects. That is why many projects are actually half done without significant and sustained direction.Originality/value: We can conclude that the typical ‘top-down’ or ‘trickle down’ conception is still dominant in design and implementation of reforms programs and service quality efforts. So, how to reach systemically at the bottom where public managers provide services to citizens, needs even more deliberation.

Policies are adopted and implemented to achieve specific goals. In this regard, the Government of Zambia in 2019 adopted the higher education policy with many objectives which include, the expansion of access to higher education; reduction of gender and other forms of inequity in accessing higher education; the improvement of quality of higher education by increasing funding to higher education institutions, construction, and repair of infrastructure in higher and improvement in the provision of learning materials in higher education institutions (HEIs).This paper, therefore, sought to evaluate the higher education policy of 2019. The four criteria were used namely; effectiveness, equity, policy sustainability, and consistency. Other principles such as political and social acceptability of a policy were not used because the policy is already adopted and being implemented. Further, the principle of efficiency was not used because it would have been problematic to gauge the expenditure against the outcomes.The findings have revealed that the policy to some extent has been effective; some of the objectives such as increased access to higher education and reduction of inequality have been partially achieved. It has been established that the number of students pursuing higher education has been increased to 114,049 in 2020 from 91,969 in 2017. Further, in 2021, 48.5% of scholarships in public universities were awarded to female students while 51.5% were awarded to female students. Further, more students are encouraged to pursue science, technology, engineering, and mathematics (STEM); and more women are pursuing studies in STEM-related fields. However, the policy has not helped to achieve the quality of higher education as funding in public HEIs has not improved. Further, infrastructure remains very poor and inadequate; and access to update and relevant learning materials also remains a challenge in HEIs. However, the policy seems to be duplicated by the recent re-launched Technical Education Vocation Entrepreneurship Training (TEVET) national policy.Given the above findings, it has been recommended that the government among other things improve funding and build infrastructure in public HEIs. There is also a need to harmonise the TEVET national policy with the higher education policy.

Malassezia is a lipid-dependent genus of yeasts known for being an important part of the skin mycobiota. These yeasts have been associated in the development of skin disorders and cataloged as a causal agent of systemic infections under specific conditions, making them opportunistic pathogens. Little is known about the host-microbe interaction of Malassezia spp., and unraveling this implies the implementation of infection models. In this mini review we present different models that have been implemented in the fungal infections study with greater attention in Malassezia spp. infections. These models range from in vitro (cell cultures and ex vivo tissue), to in vivo (murine models, rabbits, guinea pigs, insects, nematodes, and amoebas). We additionally highlight the alternative models that reduce the use of mammals as model organisms, which have been gaining importance in the study of fungal host-microbe interactions. This is due to the fact that these systems have shown to have reliable results, which correlate with those obtained from mammalian models. Example of alternative models are Caenorhabditis elegans, Drosophila melanogaster, Tenebrio molitor, and Galleria mellonella. These are invertebrates that have been implemented in the study of Malassezia spp. infections in order to identify differences in virulence between Malassezia species.

Academic entrepreneurship focuses on commercialization of research. Even though it is practiced worldwide for decades, Bangladesh is a newcomer in this segment. In Bangladesh only 2 Universities have Technology Transfer Offices or TTOs which are established with the sole focus of commercialization of researches of the students and the faculty members of the Universities. This article focuses on worldwide practices of technology transfer and academic entrepreneurial activities and also explores the opportunities and challenges of such entrepreneurs through detail investigation of the existing body of knowledge. Apart from exploring the problems and prospect of academic entrepreneurship in Bangladesh, this article also introduces the concept of Full-Service Knowledge Transfer Office (KTO), which existing literatures do not offer. The authors believe that by establishing such KTOs as a self-sustaining body, it is possible for an academic entrepreneur to stimulate, support and sustain their activities in Bangladesh. The concept of full service KTOs can also become models for other nations, specially the developing ones, to establish and nurture a culture of academic entrepreneurship.

Far-red fluorescent reporter genes can be used for tracking cells non-invasively in vivo using fluorescence imaging. Here, we investigate the effectiveness of the far-red fluorescent protein, E2-Crimson (E2C), for tracking mouse embryonic cells (mESCs) in vivo following subcutaneous administration into mice. Using a knock-in strategy, we introduced E2C into the Rosa26 locus of an E14-Bra-GFP mESC line, and after confirming that the E2C had no obvious effect on the phenotype of the mESCs, we injected them into mice and imaged them over 9 days. The results showed that fluorescence intensity was weak, and cells could only be detected when injected at high densities. Furthermore, intensity peaked on day 4 and then started to decrease, despite the fact that tumour volume continued to increase beyond day 4. Histopathological analysis showed that although E2C fluorescence could barely be detected in vivo at day 9, analysis of frozen sections indicated that all mESCs within the tumours continued to express E2C. We hypothesise that the decrease in fluorescence intensity in vivo was probably due to the fact that the mESC tumours became more vascular with time, thus leading to increased absorbance of E2C fluorescence by haemoglobin. We conclude that the E2C reporter has limited use for tracking cells in vivo, at least when introduced as a single copy into the Rosa26 locus.

The purpose of this article is to review a two year long implementation of an electronic health record (EHR) system at the outpatient department of a private hospital in Kathmandu, possibly a first implementation of its kind in Nepal. Procedures: The strategy designed for EHR implementation was based on Professor John P. Kotter's work on successful change management. Main findings: We found that keeping a close watch on the social dynamics affecting adoption decisions among users of the system was crucial for implementing the EHR; this was partly because the project received limited support from an erratically changing hospital leadership and lacked an EHR system suited to the needs of the users. Conclusions: The implementation described in this article is a good lesson on moving from control to drift in information systems implementation, and we hope this work will be useful to health IT professionals working in the space of digital transformation in resource-constrained environments.

Ovariectomy appears to be the best method to control the density of wild ungulate populations. The aim of the present study was to compare two surgical approaches, via the flank and midline, in mouflon’s ovariectomy in field conditions. Twenty female mouflons were enrolled in the study. The animals were divided randomly in two groups, Group F animals were gonadectomized via flank approach, while Group A animals were sterilized via linea alba access. The parameters evaluated were duration of surgery, duration of anaesthesia, recovery time, intra- and post-operative complications, intra-operative nociception and pain in the post-operative period. There were no intra- and post-operative complications. The evaluated parameters showed a very similar trend in both groups. Both techniques are found to be effective and safe in execution.

Recently, the indications for Cochlear Implant (CI) have also been extended to subjects with Single Sided Deafness (SSD) in order to restore binaural hearing. The primary objective of this study was to investigate the advantages of CI following one year of usage in SSD subjects. Secondarily we want to assess the long-term stability of the CI. 57 participants performed a complete audiological assessment (speech audiometry in quiet and in noise and localization test). For each was also evaluated subjective hearing profile (with Speech Spatial and Qualities_SSQ questionnaire) and the impact of tinnitus (with the use of Tinnitus Handicap Inventory_THI questionnaire) After one year of CI usage, we observed a significant improvement in speech-to-noise ratio, in sound localization abilities, in the Speech (p-value 0.001) and Spatial (p-value 0.001) subscales of the SSQ questionnaire and in THI questionnaire (p-value 0.001). The improvements in speech in noise and localization abilities and the reduction of the SSQ and THI questionnaires scores were maintained over time (6th to 60th month follow-up). Only eight participants did not fully utilize the CI. CI in SSD represents an effective method for improving speech recognition in noisy environments, restoring sound localization abilities, reducing tinnitus and improve subjective listening skills.

Malignant melanoma is one of the most aggressive and resistant tumor types which is often accompanied by poor prognosis when spread to nearby or distant tissues. Even though an increasing number of second-line therapies are available for cancer patients, the 5-year survival rate of melanoma patients with regional and distant metastases is still rather low. Therefore, there is an urgent need to develop new, highly efficient treatments. Melanocortin-1-receptor (MC1R) is a cell surface receptor for α-MSH. It is responsible for melanogenesis and is shown to be overexpressed on the surface of cancer cells in a subset of melanoma patients. Here, we designed and synthesized α-MSH analogs and conjugated them to daunomycin through oxime linkage. Using our peptide-drug conjugates (Dau-α-MSHs), we performed comparative in vitro and in vivo evaluations to reveal their suitability for tumor targeting. Firstly, the expression level of MC1R was determined in various melanoma cell lines via RT-qPCR. Then, we examined the antiproliferative effect of our Dau-α-MSHs, moreover we determined the cellular uptake profile and intracellular localization of Dau-α-MSHs. The most efficient Dau-α-MSHs were investigated in vivo using a murine xenograft melanoma model. We found that various cell lines show differential expression on the mRNA levels. We also showed that healthy primary cells have lower expression of MC1R compared to tumor cell lines. Moreover, the concentration-dependent cellular uptake profile of Dau-α-MSHs was detected and the compounds exhibited a great antiproliferative effect on melanoma cell lines. We also provided evidence that our novel Dau-α-MSHs can inhibit tumor expansion significantly and are suitable for targeted tumor therapy.

The non-structural protein (NS) and nucleoprotein (NP) of the severe fever with thrombocytopenia syndrome virus (SFTSV) encoded by the S segment are crucial for viral pathogenesis. They reside in viroplasm-like structures (VLS), but their interaction and their significance in viral propagation remain unclear. Here, we investigated the significance of the association between NS and NP during viral infection through in-silico and in-vitro analyses. Through in-silico analysis, three possible binding sites were predicted, at NSs1-32, NSs56-82, and NSs207-237. Rationally, three mutant NSs were developed by site-directed mutagenesis and tested for NP interaction by co-immunoprecipitation. NSsW61Y failed to interact with the nucleoprotein, which was substantiated by the conformational changes observed in the structural analyses. Additionally, molecular docking analysis corroborated that the NSW61Y mutant protein does not interact well compared to wild-type NS. Over-expression of wild-type NS in HeLa cells increased the SFTSV replication by five folds, but NSsW61Y exhibited 1.9-folds less viral replication than wild-type. We demonstrated that the W61Y alteration was implicated in the reduction of NS-NP interaction and viral replication. Thus, the present study identified a critical NS site, which could be targeted for development of therapeutic regimens against SFTSV.

Parkinson's Disease (PD) is a neurodegenerative disorder that affects the motor system of the human body. Currently, the available treatments are limited and often have undesirable side effects. In this context, the aim of this study was to develop a novel combinational formulation of Apomorphine and Quetiapine and evaluate its efficacy in a rat model of PD. The formulation was prepared using the solvent evaporation technique and characterized for its physicochemical properties. The in-vitro drug release was evaluated using the Franz diffusion cell method, and the pharmacokinetics of the combination was studied in rats. The behavioural and biochemical parameters were evaluated in the rats using the Rotarod, pole test, and biochemical assays. The results showed that the developed formulation had satisfactory physicochemical properties and exhibited sustained drug release. The pharmacokinetic studies showed that the combination exhibited a longer residence time than the individual drugs. The behavioural and biochemical parameters showed that the combination was effective in improving motor function and reducing oxidative stress. In conclusion, the developed Apomorphine and Quetiapine combination formulation showed promising results in improving motor function and reducing oxidative stress in rat model of PD. Further studies are required to evaluate the safety and efficacy of the developed formulation in humans.

The use of nanomaterials has been increasing in recent times, and they are widely used in industries such as cosmetics, drug, food, water treatment and agriculture. The rapid development of new nanomaterials demands a set of approaches to evaluate the potential toxicity and risks related to them. In this regard, nanosafety has been using and adapting already existing methods (toxicological approach), but the unique characteristics of nanomaterials demand new approaches (nanotoxicology) to fully understand the potential toxicity, immunotoxicity and (epi)genotoxicity. Also, new technologies, such as organ-on-chip and sophisticated sensors, are under development and/or adaptation. All the information generated is used to develop new in silico approaches trying to predict the potential effects of newly developed materials. The overall evaluation of how from the production to final disposition chain of nanomaterials is evaluated under Life Cycle Assessment (LCA), which is becoming an important element of nanosafety considering sustainability and environmental impact. In this review we give an overview of all these elements of nanosafety.

Biofouling is the unwanted adsorption of cells, proteins, or intracellular and extracellular bio-molecules that can spontaneously occur on the surface of metal nanocomplexes. It represents a major issue in bioinorganic chemistry because it leads to the creation of a protein corona, which can destabilize a colloidal solution and result in undesired macrophage-driven clearance, consequently causing failed delivery of a targeted drug-cargo. Hyaluronic acid (HA) is a bioactive, natural mucopolysaccharide with excellent antifouling properties, arising from its hydrophilic and polyanionic characteristics in physiological environments which prevent opsonization. In this study, hyaluronate-thiol (HA-SH) (MW 10 kDa) was used to surface-passivate gold nanoparticles (GNPs) synthesized using a citrate reduction method. HA functionalized GNP complexes (HA-GNPs) were characterized using absorption spectroscopy, scanning electron microscopy, zeta potential, and dynamic light scattering. GNP cellular uptake and potential dose-dependent cytotoxic effects due to treatment were evaluated in vitro in HeLa cells using ICP-OES and Trypan blue and MTT assays. Further, we quantified the in vivo biodistribution of intratumorally injected HA functionalized GNPs in Lewis Lung carcinoma (LLC) solid tumors grown on the flank of C57BL/6 mice and compared localization and retention with nascent particles. Our results reveal that HA-GNPs show overall greater peritumoral distribution (**p<0.005, 3 days post-intratumoral injection) than citrate-GNPs with reduced biodistribution in off-target organs. This property represents an advantageous step forward in localized delivery of metal nano-complexes to the infiltrative region of a tumor, which may improve the application of nanomedicine in the diagnosis and treatment of cancer.

To mitigate the COVID-19 infection, many world governments endorsed the cessation of non-essential activities, such as the school attendance. Thereby, forcing the evolution of the teaching model to the virtual classroom. In the present work we show the application of a modified version of the adapted COVID-19 stress scales (ACSS) which also included teaching anxiety and preparedness, and resilience for academic professionals in Mexico, during the unprecedented transformation of the education system undergone in the COVID-19 quarantine. Most of the studied variables: gender, age, academic degree, household occupants, having a disease, teaching level, teaching mode, work hours, resilience, teaching anxiety and preparedness, and fear of being an asymptomatic patient (FOBAP), showed significant statistical correlation between each other (p<0.050) and to the 6 areas of the ACSS (danger, contamination, social economical, xenophobia, traumatic stress and compulsive checking). Our results further showed that the perceived stress and anxiety, fell into the category of absent to mild with only the danger section of the ACSS falling into the moderate category. Finally, resilience generated throughout the quarantine, seems to be a predictor of the adaptation the academic professional has undergone to cope with stress.

Based on the geochemical analysis of the volcanic material from the sediment core AMK-340, central zone of the Reykjanes Ridge, we could detect two ash-bearing sediment units accumulated during the Termination I. They correlate to the Ash Zone I in the North Atlantic Late Quaternary sediments having an age of 12170-12840, within the Younger Dryas cold chronozone, and 13600-14540 years, within and Bølling-Allerød warm chronozone. The ash of the Younger Dryas unit is presented mostly by the mafic and persilicic material originated from the Icelandic volcanoes; Vedde Ash is presented in one sediment sample from this unit. The ash of the Bølling-Allerød unit is presented mostly by the mafic shards which are related to the basalts of the rift zone on the Reykjanes Ridge, having presumably the local origin. A detection of Vedde Ash helped to specify the timing of the previously reconstructed paleoceanographic changes for the Termination I in the point of study: a significant warming in the area could occur as early as 300 years prior to the end of the conventional Younger Dryas cold chronozone.

Microencapsulation of polyherbal formulation (PHF) extract was carried out by freeze drying method, by employing gum arabic (GA), gelatin (GE), and maltodextrin (MD) with their designated different combinations as encapsulating wall materials. Antioxidant components (i.e total phenolic contents (TPC),Total flavonoids contents (TFC), and total condensed contents (TCT)), antioxidant activity (i.e. DPPH, β-carotene & ABTS⁺ assays), moisture contents, water activity (aw), solubility, hygroscopicity, glass transition temperature (T_g), particle size, morphology, in vitro alpha-amylase and alpha-glucosidase inhibition and bioavailability ratios of the powders were investigated. Amongst all encapsulated products, T_B (5% GA and 5% MD) and T_C (10% GA) has proven to be the best treatments with respect to the highest preservation of antioxidant components and their antioxidant potential by DPPH and β-carotene assays and noteworthy for an ABTS⁺ assays, in addition, the aforesaid treatments also demonstrated lower moisture content, aw, particle size and higher solubility, hygroscopicity and glass transition temperature (T_g). All freeze dried samples showed irregular (asymmetrical) microcrystalline structures. Furthermore, T_B and T_C also illustrated the highest in vitro anti-diabetic potential due to great potency for inhibiting alpha-amylase and alpha-glucosidase activities. In the perspective of bioavailability, T_A, T_B and T_C demonstrated the excellent bioavailability ratios (%).Futhermore, the phytochemo-profiling of ethanolic extract of PHF was also revealed to find out the bioactive compounds.

Different dopamine receptor (DR) subtypes are involved in pathophysiological conditions such as Parkinson´s Disease (PD), schizophrenia and depression. While many DR-targeting drugs have been approved by the FDA, only a very small number is truly selective for one of the DR subtypes. Additionally, most of them show promiscuous activity at related G-protein coupled receptors, thus suffering from diverse side-effect profiles. Multiple studies have shown that combined in silico / in vitro approaches are a valuable contribution to drug discovery processes. They can also be applied to divulge the mechanisms behind ligand selectivity. In this study, novel DR ligands were investigated in vitro to assess binding affinities at different DR subtypes. Thus, nine D2R/D3R-selective ligands (micro- to nanomolar binding affinities, D3R-selective profile) were successfully identified. The most promising ligand exerted nanomolar D3R activity (KI = 2.3 nM) with 263.7-fold D2R/D3R selectivity. Subsequently, ligand selectivity was rationalized in silico based on ligand interaction with a secondary binding pocket, supporting selectivity data determined in vitro. The developed workflow and identified ligands could aid in the further understanding of structural motifs responsible for DR subtype selectivity, thus, benefitting drug development in D2R/D3R-associated pathologies like PD.

This paper discussed the concept of quality assurance (QA) in higher education and its implications to higher education institutions (HEIs) and the possible challenges. The study evaluated literature concerning QA in Zambia and elsewhere. The findings of the study show that QA is implemented through external and internal mechanisms such as accreditation, registration, institutional auditing, and the use of external examiners, self-evaluation, and peer reviews. The QA implications to HEIs in Zambia are that there is a need for accreditation of academic programmes with the Higher Education Authority (HEA) by HEIs. Further, HEIs should establish QA units to spearhead quality issues, reactive, and introduce the use of external examiners to ensure quality. The challenges identified in the implementation of QA in HEIs include inadequate funding, infrastructure, shortage of qualified academic staff, and lack of standalone QA units in some HEIs. In this regard, it has been recommended among other things, government improve funding in public HEIs, construct infrastructure, HEIs establish QA units, and recruit and retain qualified academic staff to ensure the quality of education.

The domain of Information and Communication Technology (ICT) education has garnered significant consideration in recent times. However, several challenges are inherent to this area of study, including monetary expense, temporal factors, pedagogical environment, teacher training programs, incentive, syllabus design, and health-related concerns. This paper presents an analysis of the difficulties encountered in the realm of ICT education in Japan, taking into account ten different perspectives.

In the rapidly advancing field of Artificial Intelligence (AI), this study presents a critical evaluation of the resilience and cybersecurity efficacy of leading AI models, including ChatGPT-4, Bard, Claude, and Microsoft Copilot. Central to this research is the use of innovative adversarial prompts designed to rigorously test the content moderation capabilities of these AI systems. The study introduces new types of adversarial tests and the Response Quality Score (RQS), a metric specifically developed to assess the nuances of AI responses. Additionally, the research spotlights FreedomGPT, an AI tool engineered to optimize the alignment between user intent and AI interpretation. The empirical results from this investigation are pivotal for assessing the current robustness and security of AI models. They highlight the necessity for ongoing development and meticulous testing to bolster AI defenses against an array of adversarial challenges. Importantly, the study also delves into the ethical and societal implications associated with employing advanced 'jailbreak' techniques in AI testing. The findings are significant for understanding AI vulnerabilities and formulating strategies to enhance the reliability and ethical soundness of AI technologies, paving the way for safer and more secure AI applications.

Contrast agents developed for X-ray computed tomography (CT) offer extremely valuable tools and techniques in diagnostics via contrast enhancements. Heavy metal-based nanoparticles (NPs) can provide high contrast in CT images. These result from a high density of heavy metal atoms with high X-ray attenuation coefficients that exceed that of iodine (I), which is currently used in hydrophilic organic CT contrast agents. Nontoxicity and colloidal stability are vital characteristics in designing heavy metal-based NPs as CT contrast agents. In addition, the particle size must be small for in vivo renal excretion. In vitro phantom imaging studies can provide X-ray attenuation efficiency, which is a critical parameter for CT contrast agents, and the imaging performance of CT contrast agents can be demonstrated via in vivo experiments. This review focuses on in vitro and in vivo studies of various heavy metal-based NPs (metal: Au, Pt, Pd, Ag, Ce, Gd, Dy, Ho, Yb, Ta, W, and Bi) and provides an outlook on their use as high-performance CT contrast agents.

Paratuberculosis (PTB) is a chronic granulomatous enteritis caused by Mycobacterium avium subsp. paratuberculosis (MAP) that affects a wide variety of domestic and wild animals. It is considered as one of the diseases with the highest economic impact in the ruminant industry. Despite many efforts and intensive research, PTB control is still controversially discussed and diagnostic and immunoprophylactic tools lack great limitations. Thus, models play a crucial role in understanding the pathogenesis of infection and disease, and in testing novel vaccine candidates. Here, we review the potential and limitations of different experimental approaches currently used in PTB research, focusing on laboratory animals and cell based models. The aim of this review is to offer a vision of the models that have been used and what has been achieved or discovered with each one so that the reader can choose the best model to answer their scientific questions and prove their hypotheses. Also, we bring forward new approaches that we consider worth exploring in the near future.