The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

Complex human behavior, including interlimb and interpersonal coordination, has been studied from a dynamical system perspective. We review the applications of a dynamical system approach to a sporting activity, which includes continuous, discrete, and switching dynamics. Continuous dynamics identified switching between in- and anti-phase synchronization, controlled by an interpersonal distance of 0.1 m during expert kendo matches, using a relative phase analysis. As discrete dynamics, return map analysis was applied to the time series of movements during kendo matches, and six coordination patterns were classified. Furthermore, state transition probabilities were calculated based on the two states, which clarified the coordination patterns and switching behavior. We introduced switching dynamics with temporal inputs to clarify the simple rules underlying the complex behavior corresponding to switching inputs in a striking action as a non-autonomous system. As a result, we determined that the time evolution of the striking action was characterized as fractal-like movement patterns generated by a simple Cantor set rule with rotation. Finally, we propose a switching hybrid dynamics to understand both court-net sports, as strongly coupled interpersonal competition, and weakly coupled sports, such as martial arts.

In this paper we provide amongst others some simple error bounds in approximating the weighted Riemann-Stieltjes integral $\int_{a}^{b}f\left(t\right) g\left(t\right) dv\left(t\right) $ by the use of three points formula \begin{equation*} f\left(b\right) \int_{c}^{b}g\left(s\right) dv\left(s\right) +f\left(a\right) \int_{a}^{d}g\left( s\right) dv\left( s\right) -f\left(x\right) \int_{c}^{d}g\left(t\right) dv\left(t\right) \end{equation*} where $x,$ $c,$ $d\in \left[a,b\right],$ $g,$ $v:\left[a,b\right] \rightarrow \mathbb{C}$ under bounded variation and Lipschitzian assumptions for the function $f$ and such that the involved Riemann-Stieltjes integrals exist.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

In this paper, we consider the development of algorithms for the solution of first order initial value problems whose solution exhibits exponential behaviour. Method of interpolation and collocation of basis function to give system of nonlinear equations which is solved for the unknown parameters to give a continuous scheme. The discrete methods recovered from the continuous scheme are implemented in block form. The stability properties of the method is verified and numerical experiments show that our method is efficient in handling these problems

(1) Background: Learning and training in variable conditions favors adapting to unstable or changing environments. The aim of the study was to test the effect of variable practice on the accuracy of the forehand net approach shot in tennis.; (2) Methods: Thirty (n=30) first-class national players (12.9 ± 1.1 years old) participated, divided into three groups: i) induced variability training (n=10) (varying court surfaces and balls), ii) specific training (n=10) and iii) usual training -control group- (n=10). All groups trained for a month: 12 sessions of 20 minutes -3 per week-. The accuracy of the shots were analyzed through a 2D capture and digitization process of the ball bounce on the court; (3) Results: The variability group presented better accuracy values after the period without practice than the stable training group (p = 0.041; ES= 0.51).; (4) Conclusions: the application of variability in the game conditions during tennis training seems to have a favorable effect on the retention of accuracy in the forehand down the line approach to the net.

Background: Healthcare workers are exposed to several hazardous chemicals in the workplace that can result in numerous adverse health effects. Several published studies from many different countries have documented the presence of metabolites from antineoplastic drugs in the urine of healthcare workers and demonstrated contaminated working surfaces with these agents. This study is a literature review that aims to compare the prevalence and degree of exposure to cyclophosphamide (CP), ifosfamide (IFO), and methotrexate (MTX) in physicians, nurses, and pharmacists in the hospital setting. Methods: An extensive search was conducted on PubMed, Google Scholar, HINARI, OARE, and Science Direct where applicable research about healthcare workers and antineoplastic drugs exposure were identified. Medical Subject Headings (MeSH) keywords: occupational exposure, antineoplastic drugs (cytotoxic drugs, cyclophosphamide, ifosfamide, methotrexate), hazardous chemicals, healthcare workers (healthcare professionals, nurses, pharmacists, physicians), hospital setting, and adverse health outcomes were used. Thereafter, relevant articles from 2000 to 2020 were selected to perform this literature review. Results: Review of literature demonstrated that cyclophosphamide was the most prevalent contaminant in the hospital setting. Additionally, pharmacists are among the group of healthcare workers with the highest prevalence of antineoplastic agents in urine samples while nursing stations had the highest rate of surface contamination. Conclusion: There is an urgent need to develop a system to monitor and detect the pathway of environmental exposure to antineoplastic drugs in the healthcare setting, and to evaluate the effectiveness of the existing protective measures. Well designed studies focusing on improving the standard safety precautions is a priority to protect healthcare workers.

In this paper, a class of nonlinear ordinary differential equations with impulses at variable times is considered. The existence and uniqueness of solution are given. At the same time, modifying the classical definitions of continuous dependence and Ga^teaux differentiability, some results on continuous dependence and Ga^teaux differentiable of solution relative to the initial value also are presented in new topology sense. For the autonomous impulsive system, the periodicity of solution is given. As an application, properties of solution for a type of controlled nonlinear ordinary differential equation with impulses at variable times is obtained. These results are foundation to study optimal control problems of systems governed by the differential equations with impulses at variable times.

Doubly-fed induction generators (DFIG) find extensive application in variable-speed wind power plants, providing notable advantages such as cost-effectiveness, operational flexibility across varying speeds, and enhanced power quality. This research focuses on the control of DFIGs employed in variable-speed wind turbine configurations. A suitable mathematical model is chosen for representative systems following a comprehensive review of contemporary research. Subsequent analysis reveals the instability of the open-loop time response of the system. To address this instability, the initial approach involves the implementation of the conventional Model Predictive Controller (MPC). However, the outcomes indicate that this controller falls short of delivering satisfactory performance despite the enhanced stability. In the subsequent phase, efforts are made to mitigate the impact of wind input variability by utilizing the Kalman filter, given its effectiveness in handling high variability. Following this, a novel methodology is introduced, which combines nonlinear MPC with the Lyapunov function. This method is based on the nonlinear model of the system. By using the Lyapunov function in the nonlinear MPC structure, the stability of the designed controller is guaranteed. The simulation results conducted using MATLAB software show that the output variables of the modeled DFIG system achieve stability within a reasonable timeframe applying the input.

This study investigated the efficacy of carvone, abscisic acid (ABA), gibberellin (GA3), and variable temperature in managing dormancy and sprouting in aeroponically grown mini-tuber potato seeds. Results showed that carvone treatment effectively reduced weight loss rate by 12.25% and decay rate by 3.33% at day 25, compared to control. ABA treatment significantly enhanced germination rate to 97.33%. GA3 treatment resulted in the longest sprouts of 14.24 mm and reduced MDA content by 23.08% at day 30, indicating its potential in shortening dormancy and maintaining membrane integrity. Variable temperature treatment showcased a balanced performance in reducing weight loss and maintaining a lower relative conductivity, indicating less cellular damage. Enzymatic activities of α-amylase, CAT, and SOD were modulated by the treatments, ensuring a balanced enzymatic environment for seed vitality. These findings provide a robust foundation for refining post-harvest management strategies to optimize germination uniformity and preserve the quality of aeroponic potato seeds during extended dormancy, promising enhanced yield and productivity in potato cultivation.

This paper presents a comparison of two methods to represent variable blade inertia in two codes for aero-servo-elastic simulations of wind turbines: the nonlinear aeroelastic multi-body model HAWC2 and the nonlinear geometrically exact beam model BeamDyn for OpenFAST. The main goal is to enable these tools to simulate the dynamic behavior of a wind turbine with variable blade inertia. However, in order to simulate the structural response of wind turbines with variable blade inertias, the source code of load simulation tools need to be modified. This is due to the fact that, currently, state-of-the-art load simulation tools for wind turbines are unable to simulate variable rotor blade inertias. The validity of the modified codes is proven based on a simple beam model. The validation shows very good agreement between the modified codes of HAWC2, BeamDyn and an analytical calculation. The add-on of variable blade inertias is applied to reduce the mechanical loads of a 5 megawatt reference wind turbine with an integrated hydraulic-pneumatic flywheel in its rotor blades.

Being able to complete the production of the product project on time is the prerequisite to win more tasks, many enterprises have begun to study intelligent scheduling algorithms to achieve dynamic control of the total project duration. However, the production operation time of products is highly volatile, and it is impossible to predict the possible operation time of future products. In the actual production environment, we often encounter extreme situations such as mixed production lines, multiple varieties, variable batches, etc. A dynamic optimization CPM model in the ERP/MES system with the attention mechanism (EMA-DCPM) will collect, extract and predict the operation time through artificial intelligence technology, and it can accurately predict the exact operation time of a batch of products that have not yet been produced. Through experiments, our algorithm can realize the production scheduling and get more than 200% better precision than former algorithms and realize dynamic optimization of complex projects.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

In the speed control system of Interior Permanent Magnet Synchronous Motor (IPMSM) without a speed sensor, the speed under the traditional PI control suffers from poor tracking performance and step response overshoot. This paper proposes a Compound Variable Structure PI (CVSPI) controller to improve the system control performance. It can choose whether to include an integral term according to the size of the system deviation to speed up the response. It also introduces a Model Reference Adaptive System (MRAS) speed observer in the controller to estimate the speed and adaptively adjust the size of the anti-integration saturation gain to improve the dynamic response following performance and immunity of the system. A feed-forward link is added for a given input differential to achieve an accurate answer to time-varying inputs. As the linear compensation matrix of the conventional MRAS is a unit matrix, the speed can only be accurately observed in a specific speed range. In this paper, a new linear compensation matrix is designed, and a new speed adaptive law is derived, allowing the improved MRAS to measure speed over a wide range accurately. Simulation results validate the excellent control performance of the CVSPI and the accuracy of the enhanced MRAS over a wide speed range.

Stage of cancer is a discrete ordinal response that indicates aggressiveness of disease and is often used by physicians to determine the type and intensity of treatment to be administered. For example, the FIGO stage in cervical cancer is based on the size and depth of the tumor as well as the level of spread. It may be of clinical relevance to identify molecular features from high-throughput genomic assays that are associated with stage of cervical cancer, to elucidate pathways related to tumor aggressiveness, identify improved molecular features that may be useful for staging, and identify therapeutic targets. High-throughput RNA-Seq data and corresponding clinical data (including stage) for cervical cancer patients has been made available through The Cancer Genome Atlas Project (TCGA). We recently described penalized Bayesian ordinal response models that can be used for variable selection for over-parameterized datasets such as the TCGA-CESC dataset. Herein, we describe our ordinalbayes R package, available from the Comprehensive R Archive Network (CRAN), which is capable of fitting cumulative logit models when the outcome is ordinal and the number of predictors exceeds the sample size, P>N, such as for TCGA data. We demonstrate use of this package through application to TCGA cervical cancer dataset. Our ordinalbayes package can be used to fit models to high-dimensional dataset and effectively performs variable selection.

This study empirically investigates the effect of productive safety net programme (PSNP) on household food consumption and dietary diversity in Ethiopia. The study applied random effects with instrumental variable to estimate the effect of PSNP membership. The result of the study indicates that though PSNP membership improves household food consumption, it reduces household dietary diversity score. Household food consumption and dietary diversity are also significantly influenced by sex, age, education status of household head, household size, livestock ownership, distance to the nearest market and participation in non-farm activities. The findings of this study suggest that PSNP membership should be reinforced by building household awareness of the benefits of consuming a variety of foods. In addition, PSNP membership should be designed to endow the households to accumulate essential assets, especially livestock.

This paper presents Chebyshev Type inequalities for the Riemann-Liouville variable-order fractional integral operator using two synchronous functions on the set of real numbers. It is the first result of its kind in the current literature using variable-order Riemann-Liouville fractional integral operator. Some special cases for the result obtained in the paper are discussed.

Renewable energy sources (RES) will play a crucial role in future sustainable energy systems. In scenarios analyzing future energy system designs, a detailed spatial and temporal representation of renewable-based electricity generation is essential. For this, sufficiently representative weather data are required. Most analyses performed in this context use the historical data of either one specific reference year or an aggregation of multiple years. In contrast, this study analyzes the impact of different weather years based on historical weather data from 1980 through 2015 in accordance with the design of an exemplary future energy system. This exemplary energy system consists of on- and offshore wind energy for power-to-hydrogen via electrolysis, including hydrogen pipeline transport for most southwestern European countries. The assumed hydrogen demand for transportation needs represents a hypothetical future market penetration for fuel cell-electric vehicles of 75%. An optimization framework is used in order to evaluate the resulting system design with the objective function of minimizing the total annual cost (TAC) of the system. For each historical weather year, the applied optimization model determines the required capacities and operation of wind power plants, electrolyzers, storage technologies and hydrogen pipelines to meet the assumed future hydrogen demand in a highly spatially- and temporally-detailed manner, as well as the TAC of the system. Following that, the results of every individual year are compared in terms of installed capacities, overall electricity generation and connection to the transmission network, as well as the cost of these components within each region. The results reveal how sensitive the final design of the exemplary system is to the choice of the weather year. For example, the TAC of the system changes by up to 20% across two consecutive weather years. Furthermore, significant variation in the optimization results regarding installed capacities per region with respect to the choice of weather years can be observed.

Multi-sensor data fusion of E-tongue and E-nose can provide a more comprehensive and more accurate analysis results. However, it also brings some redundant information, it is a hot issue to reduce the feature dimension for pattern recognition. In this paper, the taste-olfactory data fusion based on E-tongue and E-nose combined with Support Vector Machine (SVM) was used to classify five different beers. First, the taste and olfactory feature information were obtained based on E-tongue and E-nose. Second, the original feature data of single system were fused, then Principal Component Analysis (PCA) was applied to extract principal components, Genetic Algorithm-Partial Least Squares (GA-PLS) was used to select the characteristic variables, 20 subsets were generated with those variables based on the best Variable Importance of Projection (VIP) score. Finally, the classification models based on SVM were established, also c and g of SVM were calculated by Grid Search (GS), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO), the classification results of all subsets were obtained. The results showed that the classification accuracy using data fusion was much higher over single E-tongue and single E-nose, and the variable selection method by VIP had the best classification performance in #12 subset coupled with GA-SVM.

The paper presents the design stages of a single-phase Silicon Carbide bidirectional DC-AC converter. This includes the LCL filter design responsible to meet grid connection requirements. A 3kW laboratory prototype of the power converter is built employing a low-cost phase locked loop and its results are presented. The design of the low-cost phase locked loop and its implementation are depicted in some detail.

To solve large scale linear equations involved in the Fast Multipole Boundary Element Method (FM-BEM) efficiently, an iterative method named the generalized minimal residual method (GMRES)(m)algorithm with Variable Restart Parameter (VRP-GMRES(m) algorithm) is proposed. By properly changing a variable restart parameter for the GMRES(m) algorithm, the iteration stagnation problem resulting from improper selection of the parameter is resolved efficiently. Based on the framework of the VRP-GMRES(m) algorithm and the relevant properties of generalized inverse matrix, the projection of the error vector r_m+1 on r_m is deduced. The result proves that the proposed algorithm is not only rapidly convergent but also highly accurate. Numerical experiments further show that the new algorithm can significantly improve the computational efficiency and accuracy. Its superiorities will be much more remarkable when it is used to solve larger scale problems. Therefore, it has extensive prospects in the FM-BEM field and other scientific and engineering computing.

Nucleoside analogs are commonly used drugs for the treatment of cancer and viral infections. Nucleoside deoxyribosyltransferase (NDT) is one of the key enzymes required for the biosynthesis of deoxynucleotides. The feasibility of biochemical transformation processes is usually greatly dependent on the cost of biocatalysts. Therefore, immobilizing and reusing biocatalysts is an approach to be considered to bring biotransformations closer to industrial feasibility, since it not only allows enzymes to be reused but can also improve their stability under several reaction conditions. In this work, histidine tags have been successfully fused to a Nucleoside deoxyribosyltransferase from Lactobacillus reuteri (LrDNT), which has been produced in a bench-scale reactor using a facile araBAD promoter-based protein expression system in an industrial microorganism, the E. coli BL21(DE3) strain. The overexpressed LrNDT was bound to a nickel-chelating agarose affinity chromatography medium via a one-step purification and immobilization process with a 99% yield, retaining about 97% of its initial activity. The optimal conditions for the immobilized LrNDT maintain high enzyme activity within the range of 20-45°C and pH 6.0-7.5. Finally, the immobilized enzyme reactor (IMER) of LrNDT was applied for the continuous-flow biosynthesis of 2'-deoxyadenosine and retained 90% of its activity after 16 hours, providing a theoretical basis for the industrial production of nucleoside analogs.

Sustainable continuous cover forestry is defined and analyzed in several ways. The differential equation representing growth of the basal areas of individual trees, motivated by fundamental biological production theory by Lohmander (2017a), is analyzed and extended in different directions. From the solution of the differential equation, the basal area and the tree diameter are obtained as explicit functions of time. The diameter is a strictly increasing function of time. In the absence of competitors, the diameter increment is shown to be a strictly decreasing function of time. Hence, the diameter increment can also be interpreted as a strictly decreasing function of the diameter. Alternative forms of adjustment of the differential equation, with consideration of competition, are defined. If the competition is strong, with large trees in the vicinity of a particular tree, then the basal area increment, and the diameter increment, are reduced. The growth of a large tree is less sensitive than the growth of a small tree, to competition from other trees. Under strong competition, the basal area increment, and the diameter increment, are strictly concave functions of the size of the tree. The unique maximum of the diameter increment occurs at a higher diameter, if the competition increases. In dynamic equilibrium, the tree size frequency distribution is stationary. If natural tree mortality can be avoided via the harvest strategy, the tree size frequency distribution is a function of the size and competition dependent growth function, and the harvest strategy. Empirical tree size frequency data are used to simultaneously estimate parameters of a size and competition dependent growth function and the applied harvest strategy, via nonlinear optimization. The properties of the estimated growth function are consistent with the corresponding properties of the production theoretically motivated hypothetical function, and the properties of the estimated harvest strategy confirm the corresponding hypotheses. The R2 of the nonlinear regression exceeds 0.97. With access to an empirically estimated equilibrium tree size distribution, it is possible to: 1. Estimate size frequency relevant parameters of tree size and competition dependent growth functions for individual trees. 2. Estimate the applied harvest strategy. 3. Explain and reproduce the empirically estimated tree size equilibrium distribution.

During geomagnetic storms, which are a result of solar wind interaction with the Earth’s magnetosphere, geomagnetically induced currents (GICs) begin to flow in the long-distance high-voltage power grids on the Earth’s surface. It causes a number of negative phenomena that affect the normal operation of the entire electric power system. To investigate the nature of the phenomenon and its possible effects on transformers, a GIC monitoring system was created in 2011, the devices of which were installed at five substations of the Kola-Karelian power transit in northwestern Russia. Over 12 years of operating the system a large amount of data has been accumulated, which cannot be analyzed manually within a reasonable amount of time. To analyze the constantly growing volume of recorded data effectively, a method for automatic classification of GIC in autotransformer neutral was proposed. The method is based on a continuous wavelet transform of the neutral current data combined with a convolutional neural network (CNN) to classify the obtained scalogram images. As the result of comparing four CNNs with different architectures, a model that showed excellent GIC classification performance on the validation set (100.00% accuracy and loss of 0.0115) was chosen.

This study examined the relationships between attitude, subjective norms, perceived behavioral control, and behavioral intention through the perceived value of Pilates participants. The participants of this study were 301 Pilates students using Pilates studios located in Busan, Ulsan, and Gyeongbuk Province. The participants were selected by convenient sampling, a non-probability sampling method. The collected data were analyzed using descriptive analysis, reliability analysis, correlation analysis, confirmatory factor analysis, and structural equation modeling analysis using SPSS 22.0 and AMOS 24.0. The results can be summarized as follows. First, among the three subfactors of perceived value, functional and social values had a positive effect on attitude. Second, attitude, subjective norms, and perceived behavioral control, which are three main components of the Theory of Planned Behavior, had a positive effect on the behavioral intention for Pilates. These results suggest that Pilates instructors require meticulous planning and efforts to develop an environment for promoting spontaneous interest and participation to attract students and engage their attention and interest in the field.

Cut chrysanthemum, renowned as a highly favored floral choice globally, experiences a significant decline in production due to the practice of continuous cropping. The adverse physiological effects on cut chrysanthemums have been observed as a result of the degradation of soil physical and chemical properties, coupled with the proliferation of pathogens. It is noteworthy that the 'Guangyu' cultivar in Xinxiang, Henan province, China, has been specifically impacted by these effects. This study effectively identified and validated the precise pathogen accountable for wilt disease initially. Subsequently, an analysis was conducted to examine the invasion pattern of the pathogen and the physiological response of the chrysanthemum. Finally, PacBio platform was employed to investigate the dynamic alterations in the microbial community within the soil rhizosphere, comparing the effects of seven years of monocropping with the first year. The findings indicated that Fusarium solani was the primary causative agent responsible for wilt disease, as it possessed the ability to invade and establish colonies in plant roots, leading to alterations in various physiological parameters of the plants. Furthermore, the practice of continuous cropping had been observed to significantly disturb the microbial community composition, potentially acting as an additional influential factor in the advancement of wilt.

This article is a study on the (k,s)-Riemann-Liouville fractional integral, a generalization of the Riemann-Liouville fractional integral. Firstly, we introduce several properties of the extended integral of continuous functions. Furthermore, we make the estimation of the Box dimension of the graph of continuous functions after the extended integral. It presents that the upper Box dimension of the (k,s)-Riemann-Liouville fractional integral for any continuous functions is no more than the upper Box dimension of the functions on the unit interval I=[0,1], which indicates that the upper Box dimension of the integrand f(x) will not be increased by the σ-order (k,s)-Riemann-Liouville fractional integral ksD−σf(x) where σ>0 on I. Additionally, we prove that the fractal dimension of ksD−σf(x) of one-dimensional continuous functions f(x) is still one.

Most petrochemical plants still maintain a Proportional-Integral-Differential controller(PID) system, which is a feedback control system. However, gradually, the PID system is being extended and introduced to the Advanced Process Controller (APC) system, which is an integrated control system of feedforward and feedback that predicts external influences in advance. In the process of conducting on-site plant tests and calculating APC model parameter for the application of APC systems, a problem arises that Model Parameter are implemented differently depending on the proficiency of APC engineers. To minimize this problem, a technique for estimating APC model parameter without a plant test is required. In order to estimate the APC model parameter, it is necessary to train on dynamic interval data. In this paper, we use statistical techniques such as PELT, Linear Kernel, and Radial Basis Function Kernel of Change Point Detection (CPD) to extract dynamic data with minimum Mean Absolute Error (MAE) from time series data of a real petrochemical plant. Then, the hyper parameter is fixed and the APC model parameter is estimated by learning the dynamic section data. By applying the estimated APC model parameter to the APC Model Tool and measuring the fitting rate, it was confirmed that it is possible to estimate the APC model parameter with excellent control performance without plant test.

The aim of this work is to propose two different and complementary sensors for the structural health monitoring of concrete beams. In particular, a diffused sensing element and a split ring resonator network are presented. The first sensor is able to detect the variation of the dielectric properties of the concrete along the whole beam length, for a diffuse monitoring both during the important concrete curing phase and also for the entire life cycle of the concrete beams. The resonators instead work punctually, in their surroundings, allowing an accurate evaluation of the permittivity both during the drying phase and after. This allows the continuous monitoring of any presence of water both inside the concrete beam and in points that can be critical, in the case of beams in dams, bridges or in any case subject to a strong presence of water which could lead to deterioration, or worse, cause serious accidents. Moreover, the punctual sensors are able to detect the presence of cracks in the structure and to localize them.

In the context of all-digital radar systems, phase-modulated continuous wave (PMCW) based on pseudorandom binary sequences (PRBSs) appears a prominent candidate modulation scheme for applications such as autonomous driving. Among the reasons for that are its simplified transmitter architecture and lower linearity requirements, e.g., compared to orthogonal-frequency division multiplexing radars, as well as its high velocity unambiguity and multiple-input multiple-output operation capability that are characteristic of digital radars. For appropriate operation of a PMCW radar, choosing a PRBS whose periodic autocorrelation function (PACF) has low sidelobes and high robustness to Doppler shifts is paramount. In this sense, this article performs an analysis of Doppler shift tolerance of the PACFs of typically adopted PRBSs in PMCW radar systems supported by simulation and measurement results. To accurately measure the Doppler-shift-induced degradation of PACFs, peak power loss ratio (PPLR), peak sidelobe level ratio (PSLR), and integrated-sidelobe level ratio (ISLR) were used as metrics. Furthermore, to account for effects on targets whose ranges are not multiples of the range resolution, oversampled PACFs are analyzed.

The goal of this study was to analyze the forest degradation in the Reserve for San Rafael National Park, Paraguay, during the period 2005-2019. This Reserve is one of the most important forest remnants of the Upper Paraná Atlantic Forest Ecoregion. A multitemporal analysis of degradation was carried out due to the occurrence of three disturbances: forest fires, a twister and illicit crops, using the Continuous Degradation Detection (CODED) algorithm, for which 3 factors were considered: variations due to pixel in the NDFI index values before, during and after every disturbance registered. In this context, the phenomenon with the greatest impact in terms of magnitude of degradation were the forest fires of 2005, being that year at the same time, the one that reported the highest degradation values. Secondly, there are the illicit crops established until the first semester of 2019, and lastly, the twister that occurred in 2017. Our findings demonstrate that CODED algorithm can detect multi-temporal degradation events in a Subtropical Broadleaf Forest, and the post-disturbance regeneration process after every disturbance tends to occur immediately. The response in terms of degradation-regeneration is highly variable, depending of the nature and severity of each disturbance and the vegetation recovery dynamics.

The production of butanol, acetone and ethanol by Clostridium acetobutylicum is a biphasic fer-mentation process. In the first phase the carbohydrate substrate is metabolized to acetic and bu-tyric acid, in the following second phase the product spectrum is shifted towards the economi-cally interesting solvents. Here we present a cascade of six continuous stirred tank reactors (CCSTR), which allows performing the time dependent metabolic phases of an ace-tone-butanol-ethanol (ABE) batch fermentation in a spatial domain. Experimental data of steady states under four operating conditions - with variations of the pH in the first bioreactor between 4.3 and 5.6 as well as the total dilution rate between 0.042 1/h and 0.092 1/h - were used to optimize and validate a corresponding mathematical model. Beyond a residence time distribution representation and substrate, biomass and product kinetics this model also includes the differen-tiation of cells between the metabolic states. Model simulations predict a final butanol product concentration of 8.2 g/L and a butanol productivity of 0.75 g/(L h) in the CCSTR operated at a pH in bioreactor 1 of 4.3 and D = 0.092 1/h, while 31 % of the cells are differentiated to the solventogenic state. Aiming at an enrichment of solvent-producing cells, a feedback loop was introduced into the cascade - sending cells from a later state of the process (bioreactor 4) back to an early stage of the process (bioreactor 2). In agreement with the experimental observations, the model accurately predicted an increase of butanol formation rate in bioreactor stages 2 and 3, resulting in an overall butanol productivity of 0.76 g/(L h) for the feedback loop cascade. The here presented CCSTR and the validated model will serve to investigate further ABE fermentation strategies for a controlled metabolic switch.

In the field of stochastic optimisation, the so-called structural bias constitutes an undesired behaviour of an algorithm that is unable to explore the search space to a uniform extent. In this paper, we investigate whether algorithms from a subclass of estimation of distribution algorithms, the compact algorithms, exhibit structural bias. Our approach, justified in our earlier publications, is based on conducting experiments on a test function whose values are uniformly distributed in its domain. For the experiment, 81 combinations of compact algorithms and strategies of dealing with infeasible solutions have been selected as test cases. We have applied two approaches for determining the presence and severity of structural bias, namely a visual and a statistical (Anderson-Darling) tests. Our results suggest that compact algorithms are more immune to structural bias than their counterparts maintaining explicit populations. Both tests indicate that strong structural bias is found only in one of the algorithms (cBFO) regardless of the choice of strategy of dealing with infeasible solutions and cPSO mirror. For other test cases, statistical and visual tests disagree on some cases classified as having mild or strong structural bias: the former one tends to make harsher decisions, thus needing further investigation.

The livestock sector can be a major contributor to the mitigation of greenhouse (GHG) emissions. Within the sector, beef production produces the largest proportion of the livestock sector’s direct emissions. The objective of this study was to assess the on-farm GHG emissions in semi-arid rangelands in Argentina and to identify the relationships between emissions and current farm management practices. A survey recorded detailed information on farm management and characteristics. Assessments of GHG emissions were based on the IPCC Tier 2 protocols [1]. The relationships between farm management and GHG emissions were identified using General Linear Models. Cluster analysis was used to identify groups of farms that differed from others in emissions and farm characteristics. Emissions per product sold were low on farms that had improved livestock care management, rotational grazing, received technical advice, and had high animal and land productivities. Emissions per hectare of farmland were low on farms that had low stocking rates, low number of grazing paddocks, little or no land dedicated to improved pastures and forage crops, and low land productivity. Our results suggest that the implementation of realistic, relatively easy-to-adopt farming management practices has considerable potential for mitigating GHG emissions in semi-arid rangelands of central Argentina.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

Patients with predominantly antibody deficiencies (PAD) display hypogammaglobulinemia with a high prevalence of infections, along with autoimmune manifestations, benign and malignant lymphoproliferation and granulomatous disease. It is noteworthy that PAD patients, even those with defects in the same causative genes display a variable clinical phenotype, suggesting that additional genetic polymorphisms, located in either immune-related or non-immune-related genes, may affect their clinical and laboratory phenotype. In this context, we analyzed 80 PAD patients, including 70 with common variable immunodeficiency (CVID) for SERPINA1 defects, in order to investigate their possible contribution to PAD clinical phenotype. Eight CVID patients carried heterozygous pathogenic SERPINA1 defects with normal alpha-1 antitrypsin levels. Interestingly, the presence of the Z allele (rs28929474) which was found in three patients, was significantly associated with liver disease; hepatic complications were also observed in patients carrying the p.Leu23Gln (rs1379209512) and the p.Phe76del (rs775982338) alleles. Conversely, no correlation of SERPINA1 defective variants with respiratory complications was observed, although patients with pathogenic variants exhibit a reduced probability of developing autoimmune diseases. Therefore, we recommend SERPINA1 genetic analysis in PAD, in order to identify patients with a higher risk for liver disease.

An exposition is undertaken to reveal the significant impact of the time-dependent root parameter, on the stability of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing system. This opens new grounds to stability analysis of non-stationary queueing systems. Potential PSFFA applications of IoT are highlighted.

The present article investigates the threshold analysis of yielding in a variable thickness rotating disk based on the Tresca criterion. The analysis is conducted on a Functionally Graded Material (FGM) constructed from tailored materials, following the theory of small deformations and for the case of plane stress. The elasticity modulus, density, and yield stress are assumed to be power functions of the radial coordinate. Poisson’s ratio is considered constant due to small variations in different materials. Additionally, the governing equation for the rotating disk is solved analytically. Besides the material type, another factor affecting the distribution of effective stress magnitudes is the cross-sectional shape (profile) of the disk. The thickness of the cross-sectional disk varies radially as a power function. In the current analysis, different conditions for the onset of yielding and the evolution of plastic flow are considered. For evaluation and validation, the obtained results are compared and validated against similar results for specific cases (homogeneous disk and constant thickness graded disk) available in previous references. The results indicate that considering variable thickness for the disk section significantly affects the stresses and the location of the initiation of yielding

This study aimed to simulate dynamic irrigation management zones (MZs) in two maize fields for a variable rate hose-reel fertigation machine (VRFM) with a 4-section boom control. Soil moisture content was measured from nine and four soil moisture sensors in Field 1 (8.2 ha) and Field 2 (2.5 ha), respectively in different dates during the 2022 crop season. Three- and five-MZs scenarios were simulated per irrigation and the theoretical maps were processed for implementation. The application maps fitted to the VRFM showed significant spatiotemporal variations in irrigation requirements. For instance, in Field 1, 3-MZs modelling showed that the areas requiring High (H), Medium (M), and Low (L) level irrigation on July 21 were 1.60, 4.84, and 1.85 ha, respectively, whereas the farmer applied uniform rate over the whole field. H level sub-areas ranged between 1.22 ha (July 25) and 3.25 ha (July 7), showing a coefficient of variation (CV) of 43.32% for the 3-MZs, whereas H level sub-areas for 5-MZs varied from 0.41 ha (July 2) to 1.49 ha (July 7) with a CV value of 48.84%. High levels of within-field variability can be addressed using precise and dynamic irrigation MZs fitted to the irrigation technology used.

Seasonal snowpacks, characterized by their snow water equivalent (SWE), play a major role in the hydrological cycle, snow melt contributions to floods and the subsequent availability of water resources downstream. Accurately estimating SWE and understanding its spatial and temporal variations presents a considerable challenge, particularly within mountainous regions characterized by complex terrain and limited observational data. Seeking to enhance the performance of the widely used Soil and Water Assessment Tool (SWAT), we report a new approach characterising snowpack behaviour incorporating both modelled and remotely sensed derived SWE calibration data. We focus on the Chenab River Basin (CRB) a headwater catchment of the Indus Basin, globally significant in terms of human inhabitants and intensifying flood risk due to climate change. We conducted a thorough assessment of five satellite-derived and reanalysis-based precipitation datasets: ERA5-Land, CMORPH, TRMM, APHRODITE, and CPC UPP. This reveals significant levels of uncertainty in global precipitation products when compared to reference data from observed stations as well as in the resulting simulated streamflow from the SWAT model. Subsequently, we expanded the scope of the SWAT model to encompass the spatial and temporal simulation of SWE. This was achieved by incorporating information from remotely sensed and modelled SWE products, manually adjusting snow parameters in R-SWAT for both the main basin and at sub-basin scales. Integrating SWE from reference snow products into the calibration process, alongside streamflow data, substantially enhanced modelling accuracy to simulate SWE compared to the conventional auto-calibration and single-variable approaches reliant solely on streamflow data. This approach results in considerable improvement in SWE predictions and to some extent in streamflow simulation in catchments dominated by snow. This research highlights the potential of remote sensing and modelled SWE parameterisation in the absence of in-situ snowpack data in high-altitude environments. An improved understanding of SWE behaviour is vital for predicting hydrological responses spanning hazards to water resources in the populous downstream regions of the Indus Basin, especially in the face of climate change.

In this paper we overview all analytical engineering solutions for corrosion problems in pressure vessels delivered over the past 60 years. We briefly detail strengths and weaknesses of existing approaches, thus demonstrating the need for novel uniform corrosion analysis methods for both current and new applications. To complement the review, we also present a new analytical model allowing to estimate the lifetime of pressured elastic vessels with mechanically assisted corrosion. Both internal/external pressure and internal/external corrosion are captured and dissolution driven corrosion is also considered. The readily implemented method improves existing analytical approaches and is shown to be effective for thin and thick shells, as well as various loading and corrosion intensity and geometrical conditions.

Human disturbances can have severe environmental impacts on freshwater ecosystems. The main aim of this study was to detect the influences of physiochemical variables, land-cover characteristics, and river connectivity on fish assemblages in Lake Chaohu Basin, China. A cluster analysis of the river connectivity variables identified four groups of sites that characterized by significantly different connectivity gradients in local scale. These four groups of sites showed increasing connectivity from the upper reaches to the lower reaches. At the same time, among the four groups, the values of the environmental variables generally increased from the upper reaches with less human activity towards the lower reaches with more human activities. For instance, some main physiochemical variables (e.g., river width, water depth, nitrate, phosphate) significantly increased among the four groups. In contrast, fish taxa richness and diversity indices were not significantly different among the four connectivity groups. However, fish assemblages showed significant variation among the connectivity groups (p=0.026). In addition, the study determined that upper riparian land uses (e.g., woodland and grassland), flow velocity, and elevation were environmental variables regulating the variance in the fish communities, and for the connectivity variables, only river order and number of branches along a path to the left of the main stem affected the variance in the fish communities. Therefore, new practices aimed at maintaining and even increasing the riparian canopy coverage and the flow velocity of rivers should be integrated into local conservation planning for freshwater ecosystems, especially in the upper reaches of the basin.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

pump as turbine (PAT); computational fluid dynamics; variable rotational nominal speed; OpenFoam.

Variable nitrogen(N) rate fertilization based on remote sensing is challenging for cotton production fields, but active crop canopy sensors (ACS) appear as an alternative to make this practical on farm since they can be used at night as well. The crop spatial variability in inherent in crop production in general, and not on-the-go solutions can be used with this type of active sensing technologies. Thus, the purpose of this study was to investigate the potential of two vegetation indices to identify the N requirement variability for cotton plants and to develop prototype algorithms for topdressing nitrogen variable rate on commercial and experimental areas, using the N-sufficiency methodology based on virtual reference. The concept of virtual reference is to use a histogram to characterize the vegetation index of properly fertilized plants without establishing an N-rich plot as a reference strip. The experiment was conducted in strips with four different N rates (0, 45, 90 and 180 kgN ha^-1) during the 2015, 2016, 2017 and 2018 crop seasons in partnership with large cotton producers in Mato Grosso and also in experimental area of Embrapa Agrosilvopastoral. Two algorithms for variable rate nitrogen fertilization for cotton were developed, namely: 1) N recommendation algorithm for cotton in commercial production system: N rate (kg.N ha^-1) = -234.79 ISN² + 49,879 ISN + 195.15; R² = 0.97; and 2) for cotton grown in experimental area: N dose (kgN ha^-1) = -174.73 ISN² - 107.21 ISN + 306.78; R² = 0.94.

The novel coronavirus SARS-CoV2 (CoV2) emerged in December 2019. This virus has 88% genomic similarity with SARS-CoV (CoV), and both viruses largely depend on their main protease (M^pro) to regulate infection. M^pro thus represents an attractive target for anti-SARS drug design. The CoV and CoV2 M^pro are 97% identical at the sequence level, with 12 variable residues, and their X-ray structures appear similar. We thus structurally analysed how these variable residues affect the intra-molecular interactions between key residues in the CoV2 M^pro active-site. Compared to CoV M^pro, the 12 divergent residues in CoV2 M^pro exhibit modified intra-molecular interaction networks that ultimately restructure the molecular micro-environment. These altered networks also indirectly affect the networks of other active-site residues at the entrance (T26, M49 and Q192) and near the catalytic region (F140, H163, H164, M165 and H172) of the M^pro. This suggest CoV2 indirectly (via neighbours) reshape key molecular networks around the M^pro active-site. It seems that the CoV2 M^pro deceives us with its apparent structurally identical to the CoV M^pro while this viral system accumulates mass mutations (12 variable residues) at key positions. Some of these identified CoV2 M^pro networks at the active-site might guide design of efficient CoV2 M^pro inhibitors.

We have shown that the use of evolutionary gravitational constants G, the speed of light c, and cosmological constant Λ in the Einstein’s field equations leads to a very simple model that fits the supernovae Ia data with a single parameter as well as the standard ΛCDM model with two parameters, and has the predictive capability superior to the latter. We have shown that at the current time G and c both increase as dG/dt = 5.4GH₀ and dc/dt = 1.8cH₀ with H₀ as the Hubble constant, and Λ decreases as dΛ/dt = −1.2ΛH₀. Negative finding on the variation of G with time derived from the analysis of lunar laser ranging data in several studies has been attributed to the fact that these studies did not consider the variation of c simultaneously with G.

We have developed a cosmological model by allowing the speed of light c, gravitational constant G and cosmological constant Λ in the Einstein filed equation to vary in time, and solved them for Robertson-Walker metric. Assuming the universe is flat and matter dominant at present, we obtain a simple model that can fit the supernovae 1a data with a single parameter almost as well as the standard ΛCDM model with two parameters, and has the predictive capability superior to the latter. The model, together with the null results for the variation of G from the analysis of lunar laser ranging data determines that at the current time G and c both increase as dG/dt = 5.4GH0 and dc/dt = 1.8cH0 with H0 as the Hubble constant, and Λ decreases as dΛ/dt = -1.2ΛH0. This variation of G and c is all what is needed to account for the Pioneer anomaly, the anomalous secular increase of the Moon eccentricity, and the anomalous secular increase of the astronomical unit. We also show that the Planck’s constant ħ increases as dħ/dt = 1.8ħH0 and the ratio D of any Hubble unit to the corresponding Planck units increases as dD/dt = 1.5DH0. We have shown that it is essential to consider the variation of all the physical constants that may be involved directly or indirectly in a measurement rather than only the one whose variation is being considered.

Dynamic hedging has been adopted by many insurance companies to mitigate the financial risks associated with variable annuity guarantees. In order to simulate the performance of dynamic hedging for variable annuity products, insurance companies rely on nested stochastic projections, which is highly computationally intensive and often prohibitive for large variable annuity portfolios. Metamodeling techniques have recently been proposed to address the computational issues. However, it is difficult for researchers to obtain real datasets from insurance companies to test metamodeling techniques and publish the results in academic journals. In this paper, we create synthetic datasets that can be used for the purpose of addressing the computational issues associated with the nested stochastic valuation of large variable annuity portfolios. The runtime used to create these synthetic datasets would be about 3 years if a single CPU were used. These datasets are readily available to researchers and practitioners so that they can focus on testing metamodeling techniques.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

The pharmaceutical industry is undergoing a shift in processing methods for small-scale production (250-1000 kg/a), leading to an increased focus on continuous production research. Various concepts were developed to overcome challenges in small-scale crystallization for the production of high-quality products. However, further optimization is needed to enhance the industrial applicability of these concepts. This study aims to demonstrate the practical applicability of the Slug Flow Crystallizer (SFC) in the pharmaceutical industry by extending its use to a wider range of substance systems for small-scale API production. Employing an experimental strategy, the research seeks to rapidly assess the SFC's potential for achieving uniform, high-purity product yields, emphasizing the importance of factors such as slug flow stability, residence time distribution, and substance-specific crystallization criteria. This, coupled with our previously published model-based strategy, forms a comprehensive methodology to explore crystallization behavior and modeling for a variety of substance systems within the SFC. The ultimate goal of this study is to showcase the practicality of the SFC in the pharmaceutical industry, enabling the way for its reliable use in long-term, small-scale continuous crystallization and the production of high-quality pharmaceutical products.

\abstract{The existence of vorticies is well known in fluid mechanics and particularly in turbulence theory. In the context of the millennium problem of the Clay Institute on the existence (or not) of Global solutions in time of the Periodic Navier Stokes equations (PNS) results are now proposed to confirm that Global solutions do not exist in the general case of PNS defined on $\mathbb{T}^3$. This corresponds to part ($D$) proposition in the Navier Stokes problem as posted by C.Fefferman. Recent work has shown that for the Euler equations defined on the 3-Torus there exists a H\"older continuous solution for the third component of velocity $v_3$ at the center of each cell or cube of the 3-Torus Lattice. It has also been determined that as the kinematic viscosity changes from the corresponding value at $\nu=0$ to the fully viscous case for the Periodic Navier Stokes equations (PNS) at the value $\nu=1$ the solution reaches a peak ($\frac{\partial v_3}{\partial y_3} = 0$ ) in $y_3$. (third component of $\vec{r}=(y_1,y_2,y_3)$ in Cartesian co-ordinates) Here in the viscous case there exists a dipole which is not centered at the center of the cell of the Lattice. This immediately implies that since the dipole by definition has an equal in magnitude positive and negative peak in the third component of velocity, then the dipole Riemann cut-off surface is covered by a closed surface which is the sphere $\|\vec{r}\|=1$ and where a given cell of dimensions $[-1,1]^3$ is circumscribed on a sphere of radius $1$. For such a closed surface containing a dipole it necessarily follows that the flux at the surface of the sphere of $v_3$ wrt to surface normal $\vec{n}$ is zero including at $y_i, i=1\dots 3$ is zero at the points where the surface of sphere touches the cube walls. At the finite time singularity on the sphere a rotation boundary condition is deduced. Here $\frac{\partial v_3}{\partial \vec{n}}= \vec{n}\cdot \nabla v_3$. Also a boundary condition on the sphere shows rotation of sphere. Finally as a result, on the sphere a solution for $v_3$ is obtained which is proven to be H\"older continuous and it is proven that it is possible to extend H\"older continuity on the sphere uniquely to all of the interior of the ball.}

In this paper, we make research on fractal characteristics of the superposition of fractal surfaces in the view of fractal dimension. We give the upper bound of the lower and upper Box dimension of the graph of the sum of two bivariate continuous functions and calculate the exact values of them under some particular conditions. Further, it has been proved that the superposition of two continuous surfaces cannot keep the fractal dimensions invariable unless both of them are two-dimensional. A concrete example of numerical experiment has been provided to verify our theoretical results. This study can be applied to the fractal analysis of metal fracture surfaces or computer image surfaces.

Currently, old-style personal medicare techniques rely mostly on traditional methods, such as cumbersome tools and complicated processes, which can be time-consuming and inconvenient in some circumstances. Furthermore, such old methods need the use of heavy equipment, blood draws, and traditional bench-top testing procedures. Invasive ways of acquiring test samples can potentially cause patients discomfort and anguish. Wearable sensors, on the other hand, may be attached to numerous body areas to capture diverse biochemical and physiological characteristics as a developing analytical tool. Physical, chemical, and biological data transferred via the skin is used to monitor health in various circumstances. Wearable sensors can assess the aberrant conditions of the physical or chemical components of the human body in real-time, exposing the body state in time, thanks to unintrusive sampling and high accuracy. Most commercially available wearable gadgets are mechanically hard components attached to bands and worn on the wrist, with form factors ultimately constrained by the size and weight of the batteries required for the power supply. Wearable gadgets with “skin-like” qualities are a new type of automation that is only starting to make its way out of research labs and into pre-commercial prototypes. In this paper, we studied the recent advancement in battery-powered wearable sensors established on optical phenomena and skin-like battery-free sensors which brings a breakthrough in wearable sensing automation.

Fiber laser technology has been demonstrated as a versatile and reliable approach for laser source manufacturing with a wide range of applicability in various fields ranging from science to industry. The power/energy scaling of single fiber laser systems has faced several fundamental limitations. To overcome them and to boost the power/energy level even further, combining the output powers of multiple lasers has become the primary approach. Among various combining techniques, the coherent beam combining of fiber amplification channels is the most promising approach, instrumenting ultra-high power/energy lasers with near-diffraction-limited beam quality. This paper provides a comprehensive review of the progress of coherent beam combining for both continuous-wave and ultrafast fiber lasers. The concept of coherent beam combining from basic notions to specific details of methods, requirements, and challenges are discussed, along with reporting some practical architectures for both continuous and ultrafast fiber lasers.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

Due to the fact that negative energies have no existence in physical reality, the advanced mechanics of purely positive energies should describe gravitational interactions and collisions in monistic terms of extended kinetic energies and their local stresses. Such non-Newtonian mechanics of continuous inertial densities reinforces the Cartesian concept of matter-extension in the metric formalism of Einstein-Grossmann with a supplemental (dark, aether) fraction of bi-vertex mass-energy distributions. Local accelerations or decelerations of mono-vertex material densities in a multi-vertex distribution of complete kinetic energy arise under its constant integral due to nonlocal organization of continuous densities. Such integral conservation of the distributed mass-energy occurs instantaneously throughout the whole continuum of correlated densities and metric stresses despite the time-varying contributions of complementary mono-vertex and bi-vertex fractions. Under the nonlocal organization of purely kinetic (positive) mass-energy, geodesic self-heating and self-cooling of the pulsating space-matter conserve the integral energy in the two-fraction virial theorem for the averaged motion of visible mono-vertexes in the presence of invisible bi-vertex (interference, dark) mass-energy. Metric stresses of such material space are subordinate to nonlocal self-government of continuously distributed kinetic energy, including the relativistic rest-energy of General Relativity. These mutually consistent or correlated stresses in inertial space-time-energy create timelessly coordinated self-accelerations, observed for dense material volumes as distant gravitational pulls. In order to falsify/verify the nonlocal self-organization of adaptive kinetic energy, the monistic mechanics of self-consistent inertial densities and metric stresses can suggest moderate field changes in the temporal redshift, cycles of geodetic falls and takeoffs in pulsating kinetic organizations, and the calculated acceleration of the expanding Metagalaxy in its current phase of geodesic self-cooling.

Stakeholder input into the decision-making process when developing public health programs and policies is crucial. This article presents an innovative approach, involving online participation with a wide group of stakeholders located in different geographic locations, for policy consensus by research methodology. The results of the project have been used to propose assumptions regarding a strategy for preventing blood-borne diseases in Poland. The research was conducted iteratively using a multi-stage qualitative methodology to explore risk assessment involving blood-borne infections. The final output of the entire project is a list of key problems/challenges and solutions associated with medical and nonmedical services that are connected to the breakage of tissue continuity. Qualitative research is rare in risk assessment as priority is usually given to statistical data and end-points (quantitative studies ). Statistical data on health risk allows to assess the health implications, while the methodology applied also allowed diagnosis of the processes leading to these effects. In addition to policy preparation for blood-borne illnesses, the methodology employed in the study can also be used to successfully explore other areas of public health policy decisions.

A critical quality attribute of therapeutic monoclonal antibodies (mAbs) is the terminal sugar molecules of the N-linked glycan attached to the fragment crystalizable (Fc) region. There exists naturally-occurring heterogeneity in the N-linked glycan structure of mAbs, and such heterogeneity has a significant influence on the clinical safety and efficacy of mAb drugs. We previously proposed a constraint-based modeling method called glycosylation flux analysis (GFA) to characterize the rates (fluxes) of intracellular glycosylation reactions and applied the method to examine the N-linked glycosylation of immunoglobulin G (IgG) in fed-batch Chinese hamster ovary (CHO) fed-batch cultivations. In this work, we significantly improved the computational efficiency of the GFA, and employed the method to analyze the glycosylation of IgG in continuous perfusion CHO cultivations. Perfusion cell cultures have several advantages over the traditional (fed-)batch operation, including higher productivity per unit volume of reactor and more consistent product quality. The GFA showed that as in the fed-batch cultivation, the dynamical changes of IgG glycan heterogeneity in the perfusion culture are mainly attributed to alterations in the galactosylation flux activity. Furthermore, a regression analysis of the galactosylation flux activity using random forest regression linked the dynamics of galactosylation activity with the cell-specific productivity of IgG and the extracellular ammonia concentration.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

Predominantly antibody deficiencies (PAD) represent the most common type of primary immu-nodeficiencies in humans, characterized by a wide variation in disease onset, clinical manifesta-tions, complications and outcome. Considering that the prevalence of PAD in Greece is unknown and there is limited knowledge on clinical and laboratory characteristics of affected patients, we conducted a nationwide study, including 153 patients (male/female: 66/87; median age: 43.0 years; range: 7.0-77.0) diagnosed and/or followed-up between April 2007 to September 2023. Furthermore, we classified our cohort into five Groups according to their medical history, im-munoglobulin levels, and CTLA4-mutational status: 123 had common variable immunodeficien-cy (CVID), 12 with CVID-like disease (with a history of a previous B-cell depletion immunother-apy for autoimmune or malignant disease), seven with combined IgA and IgG subclass deficien-cies, five with immune dysregulation syndrome and CTLA4 defects, and six with unclassified hypogammaglobulinemia. We demonstrated a remarkable delay of PAD diagnosis, several years after the onset of related symptoms (median: 9.0 years, range: 0-43.0). Family history of PAD was only 11.8%, with the majority of patients considered sporadic cases. Most patients were diag-nosed in the context of a diagnostic work-up for recurrent infections, or recurrent/resistant auto-immune cytopenias. Interestingly, ten patients (5.6%) had no history of infection, diagnosed due to either recurrent/resistant autoimmunity, or during a work-up of their medical/family history. Remarkable findings included an increased prevalence of lymphoproliferation (60.1%) and atopy (24.2%), while 39 patients (25.5%) developed bronchiectasis and 16 (10.5%) granulomatous dis-ease. Patients with CTLA4 defects displayed a variable clinical phenotype at diagnosis, with four patients diagnosed during a work-up of re-current infections, while one also displayed a massive splenomegaly. Cancer was a common complication in our cohort (25 patients, 16.3%), with B-cell malignancies representing the most common neoplasms (56.7%). Our findings indicate the necessity of awareness about PAD and their complications, aiming for early diagnosis and appropriate management of affected patients

Regarding landscape preferences for highways, there is a dynamic interaction between users and the variety of natural and cultural landscape elements along the roadside, reflecting a balance between the highway and the natural environment. However, the rapid pace of urbanization has accelerated the development of highways, leading to the neglect or destruction of valuable landscapes. This highlights the need for visual preference assessments to protect aesthetic and environmental values. Currently, there is a lack of comprehensive criteria for assessing the visual preference of highway landscapes. Therefore, this study aims to review existing literature and establish complete assessment criteria. This study conducted a systematic literature review by searching for keywords in three databases: Web of Science, Scopus, and Google Scholar. The review included 22 papers published between 2013 and 2023 that met the criteria. An additional four relevant papers were included through a “snowballing” approach to supplement the research and results. The results of the study focused on the relationships between highway landscapes and users, user preferences, preference methods, and related variables. These inter-established relationships were used to complete an assessment framework, which establishes a basic reference standard for professionals.

We discuss the optimal control formulation for enhancement and denoising of satellite multiband images and propose to take it in the form of an L1-control problem for quasi-linear parabolic equation with non-local p[u]-Laplacian and with a cost functional of a tracking type. The main characteristic feature of the considered class of parabolic problems is the fact that the variable exponent p(t,x) and the anisotropic diffusion tensor D(t,x) are not well predefined a priori, but instead these characteristic non-locally depend on a solution of this problem, i.e., pu=p(t,x,u) and Du=D(t,x,u). We prove the existence of optimal pairs with sparse L1-controls using for that the indirect approach and a special family of approximation problems.

Surface water availability is a fundamental environmental variable to implement effective climate adaptation and mitigation plans, as expressed by scientific, financial and political stakeholders. Recently published requirements urge the need for homogenised access to long historical records at a global scale, together with the standardised characterisation of the accuracy of observations. While satellite altimeters offer world coverage measurements, existing initiatives and online platforms provide derived water level data. However, these are sparse, particularly in complex topographies. This study introduces a new methodology in two steps 1) teroVIR, a virtual station extractor for a more comprehensive global and automatic monitoring of water bodies, and 2) teroWAT, a multi-mission, interoperable water level processor, for handling all terrain types. L2 and L1 altimetry products are used, with state-of-the-art retracker algorithms in the methodology. The work presents a benchmark between teroVIR and current platforms in West Africa, Kazakhastan and the Arctic: teroVIR shows an unprecedented increase from 55% to 99% in spatial coverage.A large-scale validation of teroWAT results in an average of unbiased root mean square error ubRMSE of 0.638 m on average for 36 locations in West Africa. Traditional metrics (ubRMSE, median, absolute deviation, Pearson coefficient) disclose significantly better values for teroWAT when compared with existing platforms, of the order of 8 cm and 5% improved respectively in error and correlation. teroWAT shows unprecedented excellent results in the Arctic, using a L1 products based algorithm instead of L2 one, reducing the error of almost 4 m on average. To further compare teroWAT with existing methods, a new scoring option, teroSCO, is presented, measuring the quality of the validation of time series transversally and objectively across different strategies. Finally, teroVIR and teroWAT are implemented as platform-agnostic modules and used by flood forecasting and river discharge methods as relevant examples. A review of various applications for miscellaneous end-users is given, tackling the educational challenge raised by the community.

Regression models are mostly used in all fields of sciences for modelling the relationship between a dependent variable and independent variable(s). The least square method is often used to estimate the parameters in a linear model because it is the best linear unbiased estimator. These estimates can only be reliable if the assumption of normality is satisfied. In some cases the dependent variable might be bimodal and shows a non-linear relationship with the independent variable(s). In this case, a non-linear model should be used. In non-linear model, the standard errors are often obtained by linearizing the nonlinear function around the parameter, assuming central limit theorem. After the linearization, the least square parameter estimates are obtained. It should be noted that the error of the non-linear model is different from that of the transformed linear model. Thus, there is a need to transform back to the original non-linear model. In this note, a novel non-linear function was developed into a non-linear regression model, called Normal-Power model. The least square method was used to estimate the parameter of the transformed model. Its usefulness in regression model was demonstrated using real data of Nigeria Economy-Tourism model.

In a bid to resolve lingering problems in cosmology, more focus is being tilted towards cosmological models in which physical constants of nature are not necessarily real constants, but varying with cosmic time. In this paper we have study cosmology in nonlinear electrodynamics with the Newton's gravitational constant $G$ not a constant but vary in form of power-law of the scale factor of the universe. The evolution of the scale factor $a (t)$ is studied in this model which depends on nonlinear electrodynamics fine tuning term of $\alpha$. Then we check the stability of the model using the speed of sound.

In this study, we investigate the performance of the saddlepoint approximation of the probability mass function and the cumulative distribution function for the weighted sum of independent Poisson random variables. The goal is to approximate the hazard rate function for this complicated model. The better performance of this method is shown by numerical simulations and comparison with a performance of other approximation methods.

Complex diseases such as cancer are caused by changes in the Gene Regulatory Networks. Systems that model the complex dynamics of these networks along with adapting to real gene expression data are closer to reality and can help understand the creation and treatment of cancer. In this paper, for the first time, modelling of gene regulatory networks is performed using delayed nonlinear variable order fractional systems in the state space by a new tool called GENAVOS. This tool uses gene expression time series data to identify and optimize system parameters. This software has several tools for analyzing system dynamics. The results show that the nonlinear variable order fractional systems have very good flexibility in adapting to real data. We found that regulatory networks in cancer cells actually have a larger delay parameter than in normal cells. It is also possible to create chaos, periodic and quasi-periodic oscillations by changing the delay, degradation and synthesis rates. Our findings indicate a profound effect of time-varying order on these networks, which may be related to a type of cellular memory due to epigenetic and environmental factors. We showed that by changing the delay parameter and the variable order function for a normal cell system, its behavior changes and becomes quite similar to the behavior of a cancer cell. This work also confirms the effective role of the miR-17-92 cluster in the cancer cell cycle. GENAVOS is available at https://github.com/hanif-y/GENAVOS with its user guide and MATLAB codes.

We have shown that our varying physical constant model is consistent with the recently published variational approach wherein Einstein equations are modified to include the variation of the speed of light c, gravitational constant G and cosmological constant Λ using the Einstein-Hilbert action. The general constraint resulting from satisfying the local conservation laws and contracted Bianchi identities provides the freedom to choose the form of the variation of the constants as well as how their variations are related. When we choose dG/Gdt=3dc/cdt, ̇the same as in our quasi-phenomenological model, c=c₀ exp⁡(a^α-1), G=G₀ exp⁡[3(a^α-1)] and Λ=Λ₀ exp⁡[(a^-α-1)], where a is the scale factor and α=1.8, we are able to confirm the success of our the model in explaining three astrometric anomalies and the null results on the variation of G and the fine structure constant. We show that the model: (a) fits the supernovae 1a observational data better than the ΛCDM model; (b) determines the first peak in the power spectrum of the cosmic microwave background temperature anisotropies at multipole value of l=217.3; (c) calculates the age of the universe as 14.1 Gyr; and (d) finds the BAO acoustic scale to be 145.2 Mpc. These numbers are within less than 3% percent of the observed values and the values obtained by the ΛCDM model. Surprisingly we find that the dark-energy density is negative in a universe that has significant negative curvature and whose expansion is accelerating at a faster rate than predicted by the ΛCDM model.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

This paper proposes a single-stage asymmetrical half-bridge fly-back (AHBF) converter with resonant mode using dual-mode control. The presented converter has an integrated boost converter and asymmetrical half-bridge fly-back converter and operates in resonant mode. The boost-cell always operates in discontinuous conduction mode (DCM) to achieve high power factor. The presented converter operates simultaneously using a variable-frequency-controller (VFC) and pulse-width-modulation (PWM) controller. Unlike the conventional single-stage design, the intermediate bus voltage of this controller can be regulated depending on the main power switch duty ratio. The asymmetrical half-bridge fly-back converter utilizes a variable switching frequency controller to achieve the output voltage regulation. The asymmetrical half-bridge fly-back converter can achieve zero-voltage-switching (ZVS) operation and significantly reduce the switching losses. Detailed analysis and design of this single-stage asymmetrical half-bridge fly-back converter with resonant mode is described. A wide AC input voltage ranging from 90 to 264 Vrms and output 19 V/ 120 W prototype converter was built to verify the theoretical analysis and performance of the presented converter.

Plasminogen activator inhibitor-1 (PAI-1) has a significant role in fibrinolysis, atherogenesis, cellular senescence, and chronic inflammation. OSA (obstructive sleep apnea) leads to increased PAI-1 levels and the development of cardiovascular disease (CVD). The aim of this study was to determine the effects of CPAP therapy in patients with severe OSA on coagulation parameters and PAI-1. This prospective, controlled study enrolled 57 patients who were newly diagnosed with severe OSA, 37 of whom had had a good CPAP adherence after 6 months of therapy (usage of the device for at least 4 h per night), and their data were analyzed. The analysis showed a statistically significant increase in D-dimer values (415 (316.5-537.5) before CPAP therapy vs. 499 (327-652) after therapy, p = 0.0282) and a decrease in fibrinogen values (3.665 ± 0.752 before CPAP therapy vs. 3.365 ± 0.771) after therapy, p = 0.0075)). The PAI-1 concentration values before and after CPAP therapy did not differ significantly (17.35±7.01 ng/ml before CPAP therapy vs. 17.42±6.99 ng/ml after therapy, p = 0.9367). This study shows a tendency to improve the fibrinolytic capacity in patients with OSA after CPAP therapy although PAI-1 levels did not differ significantly.

New possibilities of Gramian computation by using canonical transformations into diagonal, controllable and observable canonical forms are shown. With the help of such a technique the Gramian matrices can be represented in the form of products of Hadamard matrices of multipliers and matrices of the transformed right-hand side of Lyapunov equations. It is shown that the multiplier matrices are invariant under various canonical transformations of linear continuous systems. The modal Lyapunov equations for continuous SISO LTI systems in diagonal form are obtained and their new solutions based on Hadamard decomposition are proposed. New algorithms for element-by-element computation of Gramian matrices for stable continuous MIMO LTI systems are developed. For continuous SISO LTI systems given by equations of state in controllable and observable canonical forms, new algorithms for the computation of controllability Gramians and their traces in the form of Hadamard products in the form of Xiao matrices are developed. The application of transformations to the canonical forms of controllability and observability allowed to simplify the formulas of spectral decompositions in the form of Xiao matrices. In the paper new spectral decompositions in the form of Hadamard’s products for solutions of Sylvester algebraic and differential equations of MIMO LTI systems, including spectral decompositions of finite and infinite cross-Gramians of continuous MIMO LTI systems. Recommendations on the use of the obtained results are given.

Background Acute kidney injury (AKI) is a common comorbidity in the intensive care unit (ICU), with higher mortality rate among those who receive continuous renal replacement therapy (CRRT). This study aimed to investigate the association of white blood cell (WBC) levels with all-cause mortality in AKI patients undergoing CRRT. Method We conducted a post hoc analysis of ICU patient data from multiple centers in Korea. First, the levels of WBCs were classified into four groups based on quartiles. Second, the relationship between different WBC levels and mortality was investigated with the Kaplan-Meier (K-M) survival curves, Cox proportional hazards model, and generalized additivity model (GAM). Finally, we used multiple imputation to avoid bias caused by non-randomized missing data. The endpoints were short-term (28 days) and long-term (90 days) mortality. Result In our analysis, a total of 1,100 ICU patients were included. Among them, 670 (60.90%) and 781 (71.00%) died within 28 and 90 days, respectively. K-M survival curves showed that patients with the lowest WBC levels had the highest risk of mortality for both outcomes. Adjusted multivariate Cox regression analysis confirmed that compared with the reference level (quartile 2), low WBC levels increased the risk of both 28-day mortality (quartile 1, HR = 1.43, 95% CI: 1.13–1.83, P = 0.004) and 90-day mortality (quartile 1: HR = 1.32; 95% CI: 1.05-1.66, P = 0.016). GAM analysis showed a non-linear, U-shaped relationship between pre-CRRT WBC levels and all-cause mortality (non-linear P < 0.05). Conclusion The baseline WBC level is an independent predictor of prognosis for ICU patients receiving CRRT. Patients in the lowest WBC quartile had the highest risk of all-cause mortality. These results provide further evidence that early observation and intervention may have a prognostic value for these high-risk patients.

The time evolution of the continuous measure symmetry for the system built of the three bodies interacting via the potential U(r)~1/r is reported. Gravitational and electrostatic interactions between the point bodies were addressed. In the case of the pure gravitational interaction the three-body-system deviated from its initial symmetrical location, described by the Lagrange equilateral triangle, comes to collapse, accompanied by the growth of the continuous measure of symmetry. When three point bodies interact via the Coulomb repulsive interaction, the time evolution of CMS is quite different. CMS calculated for all of studied initial configurations of the point charges and all of their charge-to-mass ratios always comes to its asymptotic value with time, evidencing the stabilization of the shape of the triangle, constituted by the interacting bodies.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

Type 1 Diabetes mellitus (T1DM) occurs when insulin is not produced in the Pancreas due to the autoimmune destruction of the beta cells. The patients may be diagnosed after 80-90% of the beta cells are destroyed. Insulin remains the essential medicine in T1DM management, under continuous monitoring of glucose levels. T1DM management consists of a complex and precise set of self-care measures for the entire life; during this continuous process, the patients could become overwhelmed, angry, anxious, frustrated, and/or discouraged. Therefore, to be widely used and provide general benefits, new technologies for DM management must provide clinical advantages without compromising safety. The compliance of T1DM patients is also essential, thus improving their quality of life (QoL). Moreover, the accessibility of the new system for patients through healthcare coverage is critical; they must be able to buy the new devices and accessories and pay for their maintenance. In this context, our work aims to describe the most recent technologies regarding continuous glucose monitors (CGMs) and continuous subcutaneous insulin infusion (CSII) systems, correlated with psychosocial impact and capacity to improve T1DM patients' life quality.

Gauss quadrature integral approximation is extended to include integrals with a measure consisting of a continuous as well as a discrete component. That is, we give an approximation for the integral of a function plus its sum over a discrete weighted set.

The rapid growth of smartphone financial services raises the need for secure mobile authentication. Continuous authentication is a user-friendly way to strengthen the security of smartphones by implicitly monitoring a user’s identity through sessions. Mobile continuous authentication can be viewed as an anomaly detection problem in which models discriminate between one genuine user and the rest of the imposters (anomalies). In practice, complete imposter profiles are hardly available due to the time and monetary cost, while leveraging genuine data alone yields poor generalized models due to the lack of knowledge about imposters. To address this challenge, we recast continuous mobile authentication as a few-shot anomaly detection problem, aiming to enhance the inference robustness of unseen imposters by using partial knowledge of available imposter profiles. Specifically, we propose a novel deep learning-based model, namely Local Feature Pooling based Temporal Convolution Network (LFP-TCN), which directly models raw sequential mobile data, aggregating global and local feature information. In addition, we introduce a random pattern mixing augmentation to generate class-unconstrained imposter data for the training. The augmented pool enables characterizing various imposter patterns from limited imposter data. Finally, we demonstrate practical continuous authentication using score-level fusion, which prevents long-term dependency or increased model complexity due to extended re-authentication time. Experiments on two public benchmark datasets show the effectiveness of our method and its state-of-the-art performance.

This study aims to verify the time-variant feature of American ginseng (AG) continuous cropping obstacles and to explore the factors impeding continuous cropping. We verified the feature with a plant-soil feedback pot experiment and then investigated the factors by comparing the properties of control soils that had not been previously used for growing ginseng (CS) with those of soils with a 10-year-crop-rotation cycle following the growth of AG (RS). It’s found that the survival rate of AG in RS was lower than that in CS. The RS had lower pH, available potassium content, and urease activity. Additionally, p-coumaric, p-hydroxybenzoic, vanillic, caffeic, and cinnamic acid levels were lower in RS than in CS, but salicylic acid levels showed the opposite pattern. RS had higher Rhodanobacter and lower Acidothermus, Sphingomonas relative abundances in bacterial community. It’s also found that many bacteria were substantially correlated with phenolic acids and soil physiochemical properties. Results indicate that even after 10-year crop rotation, the negative effects of prior continuous cropping of AG has not been eliminated. The growth of AG can be affected negatively with deterioration of soil physicochemical properties and with lower levels of phenolic acids which promote pathogen reproduction. Probiotics reduction also weighs. Moreover, biotic factors are interrelated with abiotic ones. Therefore, it can be inferred that the comprehensive change of soil properties is the main obstacle for continuous cropping.

The most common complication of herpes zoster is postherpetic neuralgia (PHN), which is accompanied by severe pain that lowers patients’ quality of life. Although epidural injection of local anesthetics and steroids is effective in controlling neuropathic pain resulting from herpes zoster, few studies report the efficacy and safety of epidural steroid administration in PHN patients. We randomly assigned 42 patients with severe PHN pain (visual analog scale (VAS) score ≥7) to receive continuous epidural infusion of local anesthetics with either a one-time bolus of 5 mg dexamethasone or dexamethasone pulse therapy. VAS scores significantly decreased over time for all patients, but the reduction in VAS scores and likelihood of achieving complete remission were significantly greater among patients who received dexamethasone pulse therapy, without any adverse effects. These results show that continuous epidural infusion of local anesthetics with dexamethasone is effective and safe for reducing PHN pain and promoting complete remission and that more pronounced beneficial effects are associated with more intense epidural steroid administration.

Polyhydroxyalkanoates (PHA) are microbial biopolyesters utilized as “green plastics”. Their production under controlled conditions resorts to bioreactors operated in different modes. Because PHA biosynthesis constitutes a multiphase process, both feeding strategy and bioreactor operation mode need smart adaptation. Traditional PHA production setups based on batch, repeated batch, fed-batch or cyclic fed-batch processes are often limited in productivity, or display insufficient controllability of polyester composition. For highly diluted substrate streams like it is the case for (agro)industrial waste streams, fed-batch enhanced by cell recycling were recently reported as a viable tool to increase volumetric productivity. As emerging trend, continuous fermentation processes in single-, two-, and multi-stage setups are reported, which bring the kinetics of both microbial growth and PHA accumulation into agreement with process engineering, and allow tailoring PHA´s molecular structure. Moreover, we currently witness an increasing number of CO2-based PHA production processes using cyanobacteria; these light-driven processes resort to photobioreactors similar to those used for microalgae cultivation, and can be operated both discontinuously and continuously. This development goes in parallel to the emerging use of methane and syngas as an abundantly available gaseous substrates, which also calls for bioreactor systems with optimized gas transfer. The review sheds light on the challenges of diverse PHA production processes in different bioreactor types and operational regimes using miscellaneous microbial production strains such as extremophilic Archaea, chemoheterotrophic eubacteria and phototrophic cyanobacteria. Particular emphasize is dedicated to the limitations and promises of different bioreactor-strain combinations, and to efforts devoted to upscaling these processes to industrially relevant scales.

The need for industrial and commercial machinery to maintain high torque while accurately following a variable angular speed is increasing. To meet this demand, induction motors (IMs) are commonly used with variable speed drives (VSDs) that employ a field-oriented control (FOC) scheme. Over the last thirty years, IMs have been replacing independent connection direct current motors due to their cost-effectiveness, reduced maintenance needs, and increased efficiency. However, IMs and VSDs exhibit nonlinear behavior, uncertainties, and disturbances. This paper proposes a robust combined adaptive passivity-based control (CAPBC) for this class of nonlinear systems that applies to angular rotor speed and stator current regulation inside an FOC scheme for IMs´ VSDs. It uses general Lyapunov-based design energy functions and adaptive laws with σ-modification to assure robustness after combining control and monitoring variables. Lyapunov’s second method and Barbalat Lemma prove that the control and identification error tends to be zero over time. Moreover, comparative experimental results with standard Proportional Integer controller (PIC) and direct APBC, show the proposed CAPBC effectiveness and robustness under normal and changing conditions

Solid-state fermentation (SSF) is the bioprocess where microorganisms are cultivated in the absence of free water under control conditions. Lactic acid can be produced by fermenting grape stalks with Rhizopus oryzae in SSF. During the microorganism growth, the temperature and water content of the solid bed fluctuate, leading to areas of either dry or excessive moisture in the solid substrate. Therefore, it's crucial to control the supply of water to the matrix. In this work, we obtain lactic acid through SSF of grape stalks using Rhizopus oryzae NCIM 1299. The SSF was conducted at a fixed temperature of 35 °C, with three constant relative humidity levels: 50, 65, and 80 %RH. Mathematical models, including the Logistic and First Order Plus Dead Time models for fungal biomass growth and the Luedeking and Piret with Delay Time model for lactic acid production, were adjusted to kinetic curves. Growth kinetic parameters (Xmax, μmax, Tp, T0, Yp/x and td) were determined for all conditions. These kinetic parameters were then correlated with relative humidity using a second-degree polynomial relationship. We observed a decrease in Xmax with increasing %RH, while the value of Yp/x increased at higher %RH. Finally, the optimal variable relative humidity profile was obtained by applying the Dynamic Optimization Technique, resulting in a 15.30% increase in lactic acid production.

This paper provides a new discovery that adds to the contemporary theory of modelling of non-stationary queues, by capturing analytically the behavior of the root parameter, for the G1/M/1 PSFFA model of non-stationary Ek/M/1 queue. Additionally, it has been also revealed that the resulting root parameter reduces to the PSFFA model of non-stationary queue. Potential applications of PSFFA to Computer engineering are provided. Some challenging open problems are addressed combined with closing remarks and future research directions.

Space instable target simulator (SITS) is a vital actuator for ground verification of on-orbital capture technology, the motion performance of which directly affects simulation credibility. Different delays reduce the stability of SITS and ultimately lead to its divergence. In order to achieve high fidelity simulation, the impact of force measurement delay, discrete control cycle, and simulator response delay on stability is analyzed firstly. Then, the dynamic equation and transfer function identification model of hybrid simulator is constructed, and the necessary and sufficient conditions of its stability and convergence are obtained using the Routh criterion. After that, a switching compensator with variable gain is proposed, the compensation principle diagram of which is build, and its mathematical model including the energy observer and tracking differentiator is also established. Finally, three sets of numerical simulations are conducted to validate the correctness of the stability analysis and effectiveness of proposed compensation method. Simulation results show that all three types of delay can cause SITS to lose stability under critical stable motion state, and the delay in force measurement has the greatest impact, followed by the influence of control cycle. Compared with the force applied to simulated target, velocity and its recovery coefficient of space instable target using fixed gain and linear gain compensation, the proposed compensator has significantly better performance.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

We present a new penalized method for estimation in sparse logistic regression models with group structure. Group sparsity suggests us to consider the Group Lasso penalty. Being different from penalized log-likelihood estimation, our method can be viewed as a penalized weighted score function method. Under some mild conditions, we provide non-asymptotic oracle inequalities promoting group sparsity of predictors. A modified block coordinate descent algorithm based on a weighted score function is also employed. The net advantage of our algorithm over the existing Group Lasso-type procedures is that the tuning parameter can be pre-specified. The simulations show that this algorithm is considerably faster and more stable than competing methods. Finally, we illustrate our methodology with two real data sets.

Peanuts, owing to their composition of complex carbohydrates, plant protein, unsaturated fatty acids, and essential minerals (magnesium, iron, zinc, and potassium), hold significant potential as a vital component of the human diet. Additionally, their low water requirements and nitrogen fixation capacity make them an appropriate choice for cultivation in adverse environmental conditions. The germination ability of seeds profoundly impacts the final yield of the crop, assessing seed viability of extreme importance. Conventional methods for assessing seed viability and germination are both time-consuming and costly. To address these challenges, this study investigated Visible-Near Infrared Spectroscopy (Vis/NIR) in the wavelength range of 500-1030 nm as a non-destructive and rapid method to determine the viability of two varieties of peanut seeds: North Carolina-2 (NC-2) and Spanish flower (Florispan). The study subjected the seeds to three levels of artificial aging through heat treatment, involving incubation in a controlled environment at a relative humidity of 85% and a temperature of 50°C over 24-hour intervals. The absorbance spectra noise was significantly mitigated and corrected to a large extent by combining the Savitzky-Golay (SG) and Multiplicative Scatter Correction (MSC) methods. To identify the optimal wavelengths for seed viability assessment, a range of meta-heuristic algorithms were employed, including world competitive contest (WCC), league championship algorithm (LCA), Genetics (GA), Particle Swarm Optimization (PSO), Ant Colony Optimization (ACO), imperialist competitive algorithm (ICA), learning automata (LA), heat transfer optimization (HTS), forest optimization (FOA), discrete symbiotic organisms search (DSOS), and cuckoo optimization (CUK). These algorithms offer powerful optimization capabilities for effectively extracting relevant wavelength information from spectral data. Results revealed that all the algorithms demonstrated remarkable accuracy in predicting the allometric coefficient of seeds, achieving correlation coefficients exceeding 0.985 and errors below 0.0036, respectively. In terms of execution time, the ICA (2.3635 seconds) and LCA (44.9389 seconds) algorithms exhibited the most and least efficient performance, respectively. Conversely, the FOA and the LCA algorithms excelled in identifying the least number of optimal wavelengths (10 wavelengths). Subsequently, the seeds were classified based on the wavelengths selected by the FOA (10 wavelengths) and (DSOS (16 wavelengths) methods, in conjunction with logistic regression (LR), decision tree (DT), Multilayer Perceptron (MP), support vector machine (SVM), k-nearest neighbor (K-NN), and NaiveBayes (NB) classifiers. The DSOS-DT and FOA-MP methods demonstrated the highest accuracy, yielding values of 0.993 and 0.983, respectively. Conversely, the DSOS-LR and DSOS-KNN methods obtained the lowest accuracy, with values of 0.958 and 0.961, respectively. Overall, our findings demonstrated that Vis/NIR spectroscopy, coupled with variable selection algorithms and learning methods, presents a suitable and non-destructive approach for detecting seed viability.

Variable cross-section arch is widely used in practical engineering because of its beautiful arc and excellent mechanical properties. However, there is still no systematic and comprehensive study on the out-plane buckling of variable cross-section arch. In view of this, this paper is concentrated on an elastic analytical research of out-plane buckling of arches with variable cross-section under a uniformly distributed radial local load. The pre-buckling and out-plane buckling behaviour of a variable cross-sectional arch under an external load is quite different from that of an arch with uniform cross-section. The Castigliano's second theorem is used to establish pre-buckling force method equilibrium equations for variable cross-sectional arches under a uniformly distributed radial local load, and corresponding analytical solutions of normal stress, axial compression and the bending moment are obtained. Based on the energy method and the Ritz method, analytical solutions of the critical load for the elastic out-plane buckling of arches with variable cross-section are derived. Comparisons with ANSYS results indicated that the analytical solutions are able to accurately predict the pre-buckling internal forces and critical out-plane buckling load of variable cross-section arches subjected to a uniformly distributed radial local load. It is found that the internal forces and the out-plane buckling load of an arch are significantly affected by the variation of cross-sectional height. With the ratio of cross-sectional height of the top to the end increase, the bending moment decreases and the axial force and critical out-plane buckling load increase. Analytical solutions of pre-buckling internal force and critical out-plane buckling load problems for arches with variable cross-section have a wider significance, since they can provide an effective explicit analytic method for the optimal design of arch structure.

In the crustacean immune system, leucine-rich repeat (LRR) is one of the major structures for recognizing pathogen-associated molecular patterns (PAMPs). LRR domain-containing proteins belong to the LRR family, which is a large group of proteins with more than 6000 genes in the database. They are involved in very diverse physiological functions mainly by interacting with other proteins. In a previous study, the LvLRRm, a transmembrane protein containing only LRR domain, was identified in the white leg shrimp, Litopenaeus vannamei. Its versatile role in performing multiple immunomodulation activities has been reported. However, there is still a lack of research on its efficient function at the protein level. To investigate its interactions with other proteins, we applied a convenient method called ‘Hybrid LRR technique’ to produce a recombinant LvLRRm. The LvLRRm and hagfish’s variable lymphocyte receptors (VLRs) fragments were fused to the conserved LxxLxLxxN motif while retaining the β-strand. In addition, we established interactions between hybrid-proteins and flagellin of Salmonella by performing surface plasmon resonance (SPR) analysis. The designed hybrid proteins showed potential for universal applications without losing protein functions.

This paper focuses on a joint model to analyse longitudinal proportion and survival data. After transforming the longitudinal proportional data by a logit function, we adopt a partially linear mixed-effect model for it, in which nonlinear function of time is fitted via using B-splines technique and a centered Dirichlet Process Mixture Model (CDPMM) is specified for a general distribution of random effects. The survival data is assumed to a Cox proportional hazard model, the sharing random effects joint model is developed for the two types of data. Combining the Gibbs sampler and the Metropolis-Hastings algorithm, we propose a Bayesian Lasso (BLasso) method to simultaneously estimate unknown parameters and select important covariates. Simulation studies are conducted to investigate the finite sample performance of the proposed methods. An example from the MA.5 research experiment is used to illustrate the proposed methodologies.

Physics-informed neural networks are a promising method to yield surrogate models of flow fields. We present a metamodeling technique for variable geometries based on physics-informed neural networks. The method was applied to the DU99W350 airfoil at a Reynolds number of 1×10⁵. The model predicted the Reynolds-averaged velocity and pressure field around the airfoil for arbitrary angles of attack between 10.0° and 17.5°. The model was trained with data from CFD simulations for a limited set of angles of attack. Additionally, satisfaction of the a priori known boundary conditions as well as the Reynolds-averaged Navier-Stokes equations were trained. A sensitivity analysis concerning the Reynolds number, the amount and distribution of training data, and the turbulence model was conducted showing the superiority of the pseudo-Reynolds stress method and the demand of labeled training data in the domain. The trained network was capable of predicting the developing flow separation on the suction surface and exhibited excellent agreement with CFD results even in the proximity to the wall for interpolations as well as extrapolations from the labeled data set.

Studying Active Transportation (AT) is widespread in America and Europe's research and stud-ies that include Latent variables (LV) are growing to identify exact results of finding what to do to increase the utility of AT. LVs help us to have more accurate research. LVs are defined as psy-chological factors like feeling safe while you ride at night and thus they are not subjective and hard to understand but very important to increase the utility of using AT modes. In this study, most of the previous studies about bicycling have been reviewed. In this research, different var-iables including subjective and LVs are conducted for maximizing the use of bicycle utility and introduced to have better sight for future researchers to deal with modeling AT mode choice. Results represent the importance of having 'will' for using a bicycle, especially in difficult situa-tions and cultural barriers that affect the cycling of women.

The paper aims to study the workflow of the detection center of stealthy attacks on industrial installations that generate increase in energy consumption while avoiding triggering fault detection and damaging the installation. Such long-lasting attacks on industrial facilities make production more expensive and less competitive. We present the concept of the remote detection system of cyberattacks directed at maliciously changing the controlled variable in an industrial process air conditioning system. The monitored signals are gathered at the PLC-controlled installation and sent to the remote detection system, where the discrepancies of signals are analyzed based on the Control Performance Assessment indices. The results of performed tests prove the legitimacy of the adopted approach.

This work presents an alternative to harnessing wind energy with an Electromagnetic Frequency Regulator (EFR) coupled to a hydrostatic transmission and associated with a horizontal axis wind turbine, a bidirectional frequency inverter and a secondary energy source, in a hybridized system. The hydrostatic transmision is composed by a fixed displacement axial piston pump and a variable displacement, swash plate, axial piston motor. Feedback linearization was used as a technique to control the motor geometric displacement, and a prediction algorithm for the steady state rotations of the armature and the electromagnetic field has been developed. A 5\,kW project was simulated on a Scilab platform, with combinations of constant or variable load, and constant or variable wind speed. The results indicated that the system was able to supply the generator load, adapting to fluctuations in wind speed. The possibility of storing wind energy through the inverter has also been proven. The system can accumulate energy in batteries during the fastest wind regimes, to use it when the turbine power is lower than the load.

The article presents a new approach to the analysis of the stability of automatic systems with discrete links.In almost all modern automatic control systems, there are links that break signals in time. These are power controlled switches - transistors or thyristors operating in a pulsed mode and digital links in regulators.Time discretization significantly affects the stability of processes in the automatic control system. The theoretical analysis of such systems is rather complicated and requires a significant change in engineering approaches to analysis. In connection with the improvement of digital controllers and a significant increase in their performance, in recent years this problem has practically not been remembered. However, its mathematical "content" has not changed since the 80s of the 20th century, when discreteness began to play a major role among the problems hindering progress in automatic control systems, in terms of the transition to digital systems.In this paper, a new approach is proposed, which consists in interpreting the sampling operation by a link with the proposed frequency characteristic, which determines the suppression of input high-frequency signals. This link greatly simplifies engineering calculations and demonstrates the new capabilities of sampling systems. These possibilities include the rational distribution of digitalization resources - the number of bits and the sampling interval between the regulator channels, depending on the frequency range of the efficiency of these channels. Theoretical statements have been verified and confirmed by simulation. It is shown how this approach makes it possible to formulate new principles of construction of seemingly well-known controllers - PID controllers and variable structure systems (VSS).

The extrusion-based additive manufacturing is a popular fabrication method, which has attracted the attention of various industries due to its simplicity, cheapness, ability to produce complex geometric shapes, and high production speed. One of the effective parameters in this process is the feed of filament that is presented in the production G-code. The feed of filament is calculated according to the layer height, the extrusion width and the length of printing path. All the required motion paths and filling patterns created by commercial software are a set of straight lines or circular arcs that are placed next to each other at a fixed distance. In special curved paths, the distance of adjacent ones is not equal at different points, and due to the weakness of common commercial software, it is not possible to create curved paths for proper printing. Therefore, making a special computer code that can be used to create various functions of curved paths is investigated in this research, and also the feed of filament parameter is studied in detail. Next, by introducing a correction technique, the feed of filament is changed during the curved path to distribute the polymer material uniformly. Finally, composite samples (which have variable stiffness) consisting of curved fibers are produced with the proposed method, and the high quality of printed samples confirm the suggested code and technique.

The continuous energy transformation processes in heating, ventilation and air conditioning systems of buildings are responsible for 36% of global final energy consumption. Tighter thermal insulation requirements for buildings have significantly reduced heat transfer losses. Unfortunately, this has little effect on energy demand for ventilation. On the basis of the First and the Second Law of Thermodynamics, the concepts of entropy and exergy are applied to the analysis of ventilation air handling unit (AHU) with a heat pump in this paper. This study aims to develop a consistent approach for this purpose, taking into account the variations of reference temperature and temperatures of working fluids. An analytical investigation on entropy generation and exergy analysis are used, when exergy is determined by calculating coenthalpies and evaluating exergy flows and their directions. The results show that each component of the AHU has its individual character of generated entropy, destroyed exergy and exergy efficiency variation. However, the evaporator of heat pump and fans have unabated quantities of exergy destruction. The exergy efficiency of AHU decreases from 45-55% to 12-15% when outdoor air temperature is within the range of –30°C…+10°C, respectively. This helps to determine conditions and components of improving the exergy efficiency of the AHU at variable real-world local climate conditions. The presented methodological approach could be used in the dynamic modelling software and contribute to a wider application of the Second Law of Thermodynamics in practice.

Flash flood is one of the most significant natural disasters in China, particularly in mountainous area, causing heavy economic damage and casualties of life. Accurate risk assessment is critical to an efficient flash flood management. There are more than 530,000 small watersheds in 2058 counties in China where flash flood should be prevented. In practice, with limited fund and different risk levels, the priorities of each small watershed for flash flood prevention and control are also needed for an efficient flash flood management. This paper, take Licheng county in China as an example, aims to give out these priorities for management. First, sensitive indexes are identified among index system, which includes 9 indexes based on underlying surface characteristics of small watershed in hilly region. Second, the range of each index and the rank division of each index for evaluation are determined. Based on the rank divisions for evaluation, the flash flood risk grade eigenvalue (H) is calculated by Variable Fuzzy Method (VFM ) using 1000 samplings generated by Latin hypercube sampling method. Third, the key sensitivity factors that affect flash flood risk grade eigenvalue (H) are assessed by two different global sensitivity analysis methods -- stepwise regression analysis and mutual entropy. Both results indicate that watershed slope (S) is the most sensitive factor; the second is antecedent precipitation index (CN); while other factors are slightly different sensitive in sequence. This study shows that stepwise regression analysis and mutual information analysis are appropriate for the sensitivity analysis of mountain flash flood risk. Finally, based on watershed slope (S), the priorities of flash flood prevention and control of 119 small watersheds in Licheng county are given out.