Energy storage has become a fundamental component in renewable energy systems, especially those including batteries. However, during the charging and the discharging process, there are some parameters that are not controlled by the user. That uncontrolled working leads to aging of the batteries and a reduction of their life cycle. Therefore, it causes an early replacement. Different control methods have been developed with the goal of protecting the battery and extending its life expectancy, being the most used the constant current-constant voltage. However, several studies show that charging time can be reduced by using Fuzzy Logic Control or Model Predictive Control. Other benefits are; temperature control and an extension of life expectancy. For all these reasons, FLC and MPC have proven to be more efficient than traditional charge control methods.

Quality control (QC) may be a lengthy and tedious process. As a result, most data users use data from meteorological services without performing data quality checks. The South African Weather Service (SAWS) re-established the national solar radiometric network comprising of 13 new stations within the six climatic zones of the country. This study reports on the performance results of the Baseline Surface Radiation Network (BSRN) QC procedures applied to the solar radiation data within the SAWS radiometric network. The overall percentage performance of the SAWS solar radiation network based on BSRN QC methodology is 97.79%, 93.64%, 91.6% and 92.23% for Long Wave Downward Irradiance (LWD), Global Horizontal Irradiance (GHI), Diffuse Horizontal Irradiance (DHI) and Direct Normal Irradiance (DNI) respectively with operational problems largely dominating the percentage of bad data. The overall average performance of the Surface Solar Radiation Dataset – Heliosat (SARAH) data records for the GHI estimation for all the stations showed a Mean Bias Deviation (MBD) of -8.28 Wm^-2, a Mean Absolute Deviation (MAD) of 9.06 Wm^-2 and the Root Mean Square Deviation (RMSD) of 11.02 Wm^-2. The correlation (quantified by R²) between ground-based and SARAH-derived GHI time series was ~ 0.98. The established network has the potential of providing high quality minute solar radiation data sets (GHI, DHI, DNI and LWD) and auxiliary hourly meteorological parameters vital for scientific and practical applications in renewable energy technologies in South Africa.

The process model is very essential for the model based control design. The model of the process can be identified using system identification algorithm. The system identification is done through the open loop and closed loop approaches. In this work, the lab scale conical tank setup configured as a non square MIMO system. The conical tank system is identified through the both appraoches, the effectiveness and need of the both approaces are discussed. Based on the open loop identified model the controller designed and the controller implemented in the real time the to record the process data. From this data the closed loop identification are conducted uisng N4SID algorithm. The controller seetings are obtained using the smith predcitor based IMC based PI controller for the obtained model. The proposed identification algorithm and controller tuning show the better reults over the conventional method. Moreover, this method is applicable for all the non square MIMO system.

The aim of this work is to introduce new ways to model the I-V characteristic of a PV cell or PV module using straight lines and Bézier curves. This is a complete novel approach, Bézier curves being previously used mainly for computer graphics. The I-V characteristic is divided in three sections, modeled with lines and a quadratic Bézier curve in the first case and with three cubic Bézier curves in the second case. The result proves to be accurate and relies on the fundamental points usually present in the PV cell datasheets: Voc (the open circuit voltage), Isc (the short circuit current), Vmp (the maximum power corresponding voltage) and Imp (the maximum power corresponding current) and the parasitic resistances Rsh0 (shunt resistance at Isc) and Rs0 (series resistance at Voc). The proposed algorithm completely defines all the implied control points and the error is analyzed. The temperature and irradiance influence is also analyzed. The model is also compared using the least squares fitting method. The final validation shows how to use Bézier cubic curves to accurately represent the I-V curves of an extensive range of PV cells and arrays.

Malaria and Pneumonia are leading causes of serious illness in children and adults worldwide with their death rate and prevalence on the rise. Such alarming statistics may retard the milestones so far achieved in meeting the Millennium Development Goals 4 and 6 whose targets are to improve child survival and reverse the high prevalence of diseases such as pneumonia and malaria respectively. Two sub-models of malaria-pneumonia co-infection namely malaria model and pneumonia model were considered first and then followed by the full malaria-pneumonia co-infection model. The malaria model, pneumonia model and co-infection model basic reproduction numbers denoted by R_m, R_p and R_mp respectively was obtained using the Next Generation Matrix method. The model disease free equilibrium’s local and global stability was analysed using Descartes’ Rule of signs and Comparison method. The bifurcation analysis for the malaria, pneumonia and co-infection models was studied using the Centre Manifold Theory. The sensitivity indices of the model basic reproduction numbers R_m, R_p and R_mp to the parameters in the models were calculated. Optimal control theory was applied using the Pontryagins’ Maximum Principle to investigate optimal strategies for controlling the spread of malaria, pneumonia and co-infection models using insecticide treated bed nets (u₁(t)) spraying of mosquitoes insecticides (u₂(t)), sanitation (u₃(t)), vaccination (u₄(t)), anti-malaria drugs (u₅(t)), anti-pneumonia drugs (u₆(t)), both anti-malaria drugs and anti-pneumonia drugs (u₇(t)) as the system time control variables. Numerical simulations using a set of parameter values were provided to validate the analytical results.

This paper builds on previous work introducing the Secure Remote Update Protocol (SRUP)—a secure communications protocol for Command & Control applications in the Internet of Things, built on top of MQTT. This paper builds on the original protocol, and introduces a number of additional message types: adding additional capabilities to the protocol. We also discuss the difficulty of proving that a physical device has an identity corresponding with a logical device on the network, and propose a mechanism to overcome this within the protocol.

In airborne sensor networks (ASNs), the media access control (MAC) protocol is facing with serious unfairness problem due to the traditional protection mechanism of air-to-air communications among aircrafts. Actually by using the binary exponential back-off algorithm at high traffic loads to minimize collisions among users, the latest successful node can always benefit from this kind of MAC to obtain channel resources. Moreover, when taking the existence of the hidden nodes in ASNs into account, the inaccurate traffic load information will further aggravate the system’s unfairness. In this paper, a neighbor-channel-aware (NCA) protocol is proposed to improve the fairness of MAC protocol in ASNs. In the proposal, the NCA frame is firstly added and exchanged between neighbor nodes periodically, which helps to resolve the inaccurate traffic load information, so as to avoid reducing the probability of successful message transmission. Then a traffic-loading based back-off algorithm is involved to make the neighbor nodes cooperatively adjust the inter-frame space (IFS) interval to further reduce the unfairness. The simulation results show that, the proposed MAC protocol can guarantee the satisfied fairness, simultaneously avoiding heavy network overloads to protect key messages’ successful transmissions in ASNs.

Background: The coronavirus disease-19 (COVID-19) has spread globally with more than 80,000 people infected, and nearly 3000 patients died. Currently, we are in an urgent need for effective treatment strategy to control the clinical deterioration of COVID-19 patients. Methods: The clinical data of 10 COVID-19 patients receiving short-term moderate-dose corticosteroid (160mg/d) plus immunoglobulin (20g/d) were studied in the North Yard of The First Hospital of Changsha, Hunan from January 17^th to February 27^th, 2020. Epidemiological, clinical, laboratory, radiological findings were analyzed. Results: After treatment with combination of low-dose corticosteroid (40-80mg/d) and immunoglobulin (10g/d), patients’ lymphocyte count (0.88±0.34 vs 0.59±0.18, P<0.05), oxygenation index including SPO₂ (94.90±2.51 vs 90.50±5.91, P<0.05) and PaO₂/FiO₂ (321.36±136.91 vs 129.30±64.97, P<0.05) were significantly lower than pre-treatment, and CT showed that the pulmonary lesion deteriorated in all patients. While after treatment of short-term moderate-dose corticosteroid plus immunoglobulin, patients’ APACHE Ⅱ score (9.10±6.15 vs 5.50±9.01, P<0.05), body temperature (37.59±1.16 vs 36.46±0.25, P<0.05), lymphocyte count (0.59±0.18 vs 1.36±0.51, P<0.05), Lactate dehydrogenase (419.24±251.31 vs 257.40±177.88, P<0.05), and C-reactive protein (49.94±26.21 vs 14.58±15.25, P<0.05) significantly improved compared with post-treatment with low-dose therapy. In addition, oxygenation index including SPO₂ (90.50±5.91 vs 97.50±1.18, P<0.05), PaO₂ (60.47±14.53 vs 99.07±34.31, P<0.05), and PaO₂/FiO₂ (129.30±64.97 vs 340.86±146.72, P<0.05) significant improved. Furthermore, CT showed that pulmonary lesions obviously improved in 7 patients. After systematic therapy, 4 out of 10 COVID-19 patients recovered and discharged. Conclusions: Short-term moderate-dose corticosteroid plus immunoglobulin is effective for reversing the continued deterioration of COVID-19 patients who failed to respond to the low-dose therapy. Funding: This work was supported by the Innovative Major Emergency Project Funding against the New Coronavirus Pneumonia in Hunan Province (Dr. Ji-Yang Liu, number 2020SK3014; Dr. Yuan-Lin Xie, number 2020SK3013).

A programmable DC power supply with Real-time Digital Simulator (RTDS)-based photovoltaic (PV) Power Hardware-In-the-Loop (PHIL) simulators have been used to improve the control algorithm and reliability of PV Inverter. This paper proposes a supervisory control algorithm for PV PHIL simulator with non-RTDS device that is an alternative solution of high cost PHIL simulator. However, when such a simulator with conventional algorithm which is used in RTDS is connected to a PV inverter, the output is in the transient state and it makes it impossible to evaluate the performance of the PV Inverter. Therefore proposed algorithm controls the voltage and current target values according to the constant voltage (CV) and constant current (CC) modes to overcome the limitation of the Computing Unit, DC power supply and also uses a multi-rate system to account for the characteristics of each component of simulator. A mathematical models of a PV system, programmable DC power supply, isolated DC measurement device and Computing Unit are integrated to form a real-time processing simulator. Performance tests using a PV PHIL simulator which is applied proposed algorithm connected a PV inverter are carried out and proved superiority and utility of this method against conventional methods.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

This paper investigates a distributed, coordinated motion control network based on multiple direct-drive, linear switched reluctance machines (LSRMs). A hierarchical, two-level synchronization control strategy is proposed for the four LSRMs based motion control network. The high-level, reference signals agreement algorithm is first employed to correct the asynchronous behaviors of the position commands. Then, the low-level tracking synchronization method is applied for the collaborative position control of the four LSRMs. The proposed two-level, fault-tolerant control strategy eliminates the asynchrony of the reference signals and it also guarantees the coordinated tracking control performance of the four LSRMs. Experimental results demonstrate that effective coordinated tracking control can be ensured, based on successful agreement of reference signals and an absolute tracking error falling within 2 mm can be achieved.

With the proliferation of locating devices, more and more raw spatial trajectories are formed, and many works enrich these raw trajectories with semantics, and mine patterns from both raw and semantic trajectories, but access control of spatial trajectories is not considered yet. We present a multi-policy secure model for semantic spatial trajectories. In our model, Mandatory Access Control, Role Based Access Control and Discretionary Access control are all enforced, separately and combined, and we represent the model semi-formally in Ontology Web Language.

Bipedal locomotion remains one of the major open challenges of humanoid robotics. The common approaches are based on simple reduced model dynamics to generate walking trajectories, often neglecting the whole-body dynamics of the robots. As motions in nature are often considered as optimal with respect to certain criteria, in this work we present an optimal control based approach that allows us to generate optimized walking motions using a precise whole-body dynamic model of the robot, in contrast with the common approaches. The optimal control problem is formulated to minimize a set of desired objective functions with respect to physical constraints of the robot and contact constraints of the walking phases. We apply the method with combinations of different objective criteria to the model of a reduced version of the iCub humanoid robot of 15 internal DOF. The obtained trajectories are executed on the real robot and we carry out a discussion on the differences between the outcomes of this approach with the classic approaches.

Abstract— Flight Control System is an integrated avionics system equipped with the minimum required components for an autonomous flight. This paper focuses on the Hardware Design of the Flight Control System and presents specific details of the components and its interface. The system architecture is based on Field Programmable Gate Array and Digital Signal Processor. Employing these two processors in the flight control system would improve the Flight Control System performance in terms of fast sequential processing of high-level control algorithms. In addition to Field Programmable Gate Array and Digital Signal Processor, the flight control computer system will also make use of Global Positioning System and Micro Electro Mechanical System sensors. The project will be implemented using Altera’s System On Programmable Chip builder, currently known as Qsys – Platform Designer implemented in Quartus-II. The system employs Nios-II processor which is 32-bit soft-core embedded-processor architecture designed especially for the Altera’s family of Field Programmable Gate Array. From conceptualization to final design, this paper presents the functionality of the different modulus and complex interfaces employed in this Flight Control System.

Permanent magnet synchronous motor (PMSM) AC servo system shows the characteristics of uncertainty, time-varying and non-linearity, which makes it difficult for traditional PID control to achieve ideal control effect. Fuzzy control has strong adaptability to the problems of parameter variation, non-linearity and model inaccuracy of the controlled object. Vector control strategy is used to study its control principle and the realization of SVPWM. Because the motor object has certain fractional order characteristics, the fuzzy parameter self-tuning PIλ control is chosen as the position regulator of servo motor. It combines the accuracy of fractional order PI control and the adaptability of fuzzy control. A simulation model of PMSM three-closed-loop system is built in MATLAB/Simulink environment. The results show that the control method is effective and can satisfy the trajectory tracking of servo control.

In this paper, modelling designing and simulation of a Ward Leonard layout system is done using robust control theory. In order to increase the performance of the Ward Leonard layout system with H infinity optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers are used. The open loop response of the Ward Leonard layout system shows that the system needs to be improved. Comparison of the Ward Leonard layout system with H∞ optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers to track a desired step speed input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed Ward Leonard layout system with H infinity optimal control synthesis controller in improving the percentage overshoot and the settling time.

Control as a Service (CaaS) is an emerging paradigm where low-level control of a device is moved from a local controller to the Cloud, and provided to the device as an on-demand service. Among its many benefits, CaaS gives the device access to advanced control algorithms which may not be executable on a local controller due to computational limitations. As a step toward 3D printer CaaS, this paper demonstrates the control of a 3D printer by streaming low-level stepper motor commands (as opposed to high-level G-codes) directly from the Cloud to the printer. The printer is located at the University of Michigan, Ann Arbor, while its stepper motor commands are calculated using an advanced motion control algorithm running on Google Cloud computers in South Carolina and Australia. The stepper motor commands are sent over the Internet using the user datagram protocol (UDP) and buffered to mitigate transmission delays; checks are included to ensure accuracy and completeness of the transmitted data. All but one part printed using the cloud-based controller in both locations were hitch free (i.e., no pauses due to excessive transmission delays). Moreover, using the cloud-based controller, the parts printed up to 54% faster than using a standard local controller, without loss of accuracy.

The outbreak of Coronavirus disease 2019 (COVID-19) has posed a significant concern in many countries due to the rapid rate of transmission between humans. Taking advantage of the experience of the last epidemics in 2002 Severe Acute Respiratory Syndrome Coronavirus (SARS-CoV) and 2012 Middle East Respiratory Syndrome Coronavirus (MERS-CoV), some regions of the world were well- prepared for the new outbreak. However, other countries needed to be adapted to the situation promptly. Many management strategies were established, and some restrictions were introduced in some regions. In this review, we aimed to determine countries’ public responses to the epidemic of COVID-19 and how they developed administrative approaches towards the outbreak.

This research work explains the practical realization of hybrid solar wind based standalone power system with maximum power point tracker (MPPT) to produce electrical power in rural places (residential applications). The solar inspired Ant Colony Optimization (ACO) based MPPT algorithm is employed for the purpose of fast and accurate tracking power from solar and wind system. Fuzzy Logic Control (FLC) inverter controlling strategy is adopted in this presented work compared to classical PI control. Moreover, single Cuk converter is operated as impedance power adapter to execute MPPT functioning. Satisfactory practical results have been realized using dSPACE (DS1104) platform that justify the superiority of proposed algorithms designed under various operating situations.

Incorporating linear-scanning MEMS micromirrors into Fourier transform spectral acquisition systems can greatly reduce the size of the spectrometer equipment, making portable Fourier transform spectrometers (FTS) possible. How to minimize the tilting of the MEMS mirror plate during its large linear scan is a major problem in this application. In this work, an FTS system has been constructed based on a biaxial MEMS micromirror with a large piston displacement of 180 μm, and a biaxial H∞ robust controller is designed. Compared with open-loop control and PID closed-loop control, H∞ robust control has good stability and robustness. The experimental results show that the stable scanning displacement reaches 110.9 μm under the H∞ robust control, and the tilting angle of the MEMS mirror plate in that full scanning range falls within ±0.0014°. Without control, the FTS system cannot generate meaningful spectra. In contrast, the FTS yields a clean spectrum with an FWHM spectral linewidth of 96 cm-1 under the H∞ robust control. Moreover, the FTS system can maintain good stability and robustness under various driving conditions.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.

The coronavirus disease 2019 (COVID-19) pandemic has led to wastewater surveillance becoming an important tool for monitoring the spread of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) within communities. As a result, molecular methods, in particular reverse transcription-quantitative PCR (RT-qPCR), have been employed to generate large data sets aimed at the detection and quantification of SARS-CoV-2 in wastewater. Although RT-qPCR is rapid and sensitive, there is no standard method that fits all use cases, there are no certified quantification standards and experiments are carried out using numerous different assays, reagents, instruments, and data analysis protocols. These variations can lead to the reporting of erroneous quantitative data resulting in potentially misleading interpretations and conclusions. We have reviewed the SARS-CoV-2 wastewater surveillance literature focusing on the variability of RT-qPCR data as revealed by inconsistent standard curves and associated parameters. We find that variation in these parameters and deviations from best practices as described in The Minimum Information for Publication of Quantitative Real-Time PCR Experiments (MIQE) guidelines suggest a lack of reproducibility and reliability in quantitative measurements of SARS-CoV-2 RNA in wastewater.

Background: Scabies is an unfortunately neglected tropical skin disease. Scabies occurs in Australia, however it is drastically more common amongst select socioeconomically disadvantaged groups. Amongst these, Aboriginal and Torres Strait Islander communities are affected particularly severely, likely secondary to rampant overcrowding. Methods: This literature review has comprehensively explored the relevant evidence available since the year 2000. Objectives: The objective of this article is to provide updates on the identification, management, and control of scabies in Aboriginal and Torres Strait Islander communities. The article also aims to reveal issues with these factors that may be contributing to the inflated prevalence of scabies amongst these groups. Conclusions: Diagnosis currently depends upon clinical examination, dermatoscopy, and skin scraping microscopy; all of which are prone to error. In Australia, topical permethrin remains first-line treatment, however resistance is developing. Other management aspects to consider are environmental measures and treating secondary infections. Scabies prevention is far more cost-effective than managing advanced individual cases, typically ensured through mass drug administration of permethrin or ivermectin. Sustained prevention can prove troublesome for some communities. In order to address the status of scabies as a neglected tropical disease, these issues must be managed first.

Primates have an unparalleled ability to produce a wide range of dexterous movements, each sensitive to context and robust to perturbation. Recent progress in understanding the neural basis of movement generation comes from two largely independent ideas, “Optimal Feedback Control” and “Neural Dynamical Systems”. The optimal control framework was largely inspired by research programs from the ‘80s showing that the brain doesn’t seem to plan a simple desired movement trajectory, but instead produces movements by transforming sensory information into motor output that satisfies an optimality criterion. The more recent idea that the motor cortex acts as a dynamical system came about only as it became possible to analyze large numbers of simultaneously recorded single neurons. These two framings of the motor system have been largely incommensurate, neither able to contribute much to the understanding of the other. In this review, we reconcile these two views into a single model we call “Dynamical Feedback Control”. We propose that the dynamics in the motor cortex emerge from a sensorimotor transformation that couples the motor cortex to sensory input from the periphery, and to contextual inputs from other cortical and subcortical areas. Dynamics in motor cortex can be thought to approximate gains of a feedback controller, and by moving the neural state to different regions of state space, the motor system can rapidly alternate between different controllers. The DFC framework presents a new lens to interpret neural dynamics, and to understand how ensembles of neurons generate flexible and responsive patterns of muscle activity.

Autonomous navigation of spacecraft necessitates innovative technologies, methods, and algorithms, particularly when orbiting in proximity of other space objects. Optimization methods are useful for autonomous spacecraft navigation, guidance, and control, but their performance is hampered by noisy multi-sensor technologies and poorly modeled system equations, and real-time on-board utilization is generally computationally burdensome. Some proposed methods use noisy sensor data to learn the optimal guidance and control solutions real-time (online), where non-iterative instantiations are preferred to reduce computational burdens. This study aims to highlight efficacy and limitations of several common methods for optimizing guidance and control while proposing a few more, where all methods are applied to the full, nonlinear, coupled equations of motion including cross-products of motion from the transport theorem. Five disparate types of optimum guidance and control algorithms are presented and compared to a classical benchmark. Comparative analysis is based on tracking errors (both states and rates), fuel usage, and computational burden. Real-time optimalization with singular switching plus nonlinear transport theorem decoupling proves superior by matching open-loop solutions to the constrained optimization problem (in terms of state and rate errors and fuel usage), while robustness is validated in the utilization of mixed, noisy state and rate sensors and uniformly varying mass and mass moments of inertia. State tracking errors are reduced one-hundred ten percent. Rate tracking errors are reduced one-hundred thirteen percent. Control utilization (e.g., fuel) is reduced eighty four percent, while computational burden in reduced ten percent simultaneously.

Plant diseases cause losses of approximately 16% globally. Thus, management measures must be implemented to mitigate losses and guarantee food production. In addition to traditional management measures, resistance induction and biological control have gained ground in agriculture due to their enormous potential. Endophytic fungi colonize plant tissues internally and have the potential to act as biological control agents, as elicitors in the process of resistance induction and in attenuating abiotic stresses. In this review, we list the action of this group of microorganisms as potential agents which can act in controlling plant diseases and describe several examples in which endophytes were able to reduce the damage caused by pathogens and adverse conditions. This is due to their arsenal of molecules generated during the interaction by which they form a kind of biological shield in the plant. Studies on these microorganisms have grown due to the existing diversity and the multiple benefits they can offer. Finally, considering that endophytic fungi can be an important tool in managing diseases due to the large amount of biologically active substances produced, bioprospecting this class of microorganisms is tending to increase and generate valuable products.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

In addition to provide an extremely clean environment for primary loop of high-temperature gas-cooled reactor (HTR), the primary helium circulator (PHC) using electromagnetic levitation technology also provides an effective means for vibration control. Besides synchronous vibration produced by mass imbalance and sensor runout, double-frequency vibration produced by unbalanced magnetic pull (UMP) is serious in PHC engineering prototype (PHC-EP). In this paper, we firstly analyzed the mechanism of UMP and the multi-frequency vibration characteristics in combination with the PHC-EP. Then we put forward a distributed iterative learning control (ILC) algorithm and a parallel control scheme to suppress the periodic vibrations. Finally, we verified the methods by carrying out experimental researches on the active magnetic bearing (AMB) bench of PHC-EP. The results show that the methods put forward in this paper have significant control effect on the double-frequency vibration generated by UMP of the PHC-EP, and provide theoretical and practical references for the PHC safe operation in HTR.

Currently, energy security and environmental degradation are the two biggest challenges before humanity that can be surmounted with the use of green and sustainable biofuels produced from lignocellulosic crops. In the future, to ensure adequate and cost-effective supply of biofuels, it requires a sufficient amount of amenable and quality lignocellulosic feedstocks. Therefore, agricultural yields of lignocellulosic biomass crops should be substantially increased by intense genetic maneuvering of key gene regulatory mechanisms and signaling pathways that control plant biomass yield. Recently, numerous miRNAs families are identified, characterized, and validated across the plant kingdom. Plant microRNAs (miRNAs) are 21 to 24 nucleotides long, non-coding small RNAs, act as regulators of their target genes via inducing modifications in transcription, translation, and epigenome. MiRNAs represent many hallmark characteristics like sequence-specific regulation, tissue, and species-specific expression, evolutionary conservation, and functional diversity. They coordinate well physiological and life cycle processes in plants under adverse environmental conditions. Hence, miRNAs offer accurate, precise, and efficient regulatory switches in the miRNA-targeted genetic networks. It is evident from the study of the miR156 family and its target SQUAMOSA PROMOTER BINDING PROTEIN-LIKE (SPL) genes network that controls highly significant agronomic traits in crop plants. The miR156/SPL module acts as a master circuit that synchronizes many intricate complex biological functions such as growth and development, and metabolic processes by sensing internal and external environmental signals in plants. Therefore, miR156 can prove a potential target for miRNAs based plant biotechnology to harmonize complex biofuel traits and improve biomass yield in lignocellulosic biomass crops.

Polymeric wet-strength agents are important additives used in the paper industry to improve the mechanical properties of paper products, especially when they come in contact with water. These agents play a crucial role in enhancing the durability, strength, and dimensional stability of paper products. The aim of this review is to provide an overview of the different types of wet-strength agents available and their mechanisms of action. We will also discuss the challenges associated with the use of wet-strength agents and the recent advances in the development of more sustainable and environmentally friendly agents. As the demand for more sustainable and durable paper products continues to grow, the use of wet strength agents is expected to increase in the coming years.

This paper describes a novel thruster fault-tolerant control system (FTC) for open-frame remotely operated vehicles (ROVs). The proposed FTC consists of two subsystems: a model-free thruster fault detection and isolation subsystem (FDI) and a fault accommodation subsystem (FA). The FDI subsystem employs fault detection units (FDUs), associated with each thruster, to monitor their state. The robust, reliable and adaptive FDUs use a model-free pattern recognition neural network (PRNN) to detect internal and external faulty states of the thrusters in real time. The FA subsystem combines information provided by the FDI subsystem with predefined, user-configurable actions to accommodate partial and total faults and to perform an appropriate control reallocation. Software-level actions include penalisation of faulty thrusters in solution of control allocation problem and reallocation of control energy among the operable thrusters. Hardware-level actions include power isolation of faulty thrusters (total faults only) such that the entire ROV power system is not compromised. The proposed FTC system is implemented as a LabVIEW virtual instrument (VI) and evaluated in virtual (simulated) and real-world environments. The proposed FTC module can be used for open frame ROVs with up to 12 thrusters: eight horizontal thrusters configured in two horizontal layers of four thrusters each, and four vertical thrusters configured in one vertical layer. Results from both environments show that the ROV control system, enhanced with the FDI and FA subsystems, is capable of maintaining full 6 DOF control of ROV in the presence of up to 6 simultaneous total faults in the thrusters. With the FDI and FA subsystems in place the control energy distribution of the healthy thrusters is optimised so that the ROV can still operate in difficult conditions under fault scenarios.

This paper presents findings of a study on continuous feed-in management and continuous synthetic inertia contribution with wind turbines. A realistic case study, based on real measurements, is outlined. A wind turbine feeds into a weak feeder, such that its power has to be adapted to the permissible loading of this feeder. At the same time the wind turbine is to provide inertia to the grid by applying the previously published variable inertia constant controller. It is discussed that optimal grid utilisation and simultaneous inertia contribution are mandatory for the frequency control in power systems that are heavily penetrated with renewable energies. The study shows that continuous feed-in management can be combined well with continuous inertia provision. There are hardly any negative consequences for the wind turbine. The benefits for the grid are convincing, both in terms of increased system utilisation and in terms of provided inertia. It is concluded that wind turbines can enhance angular stability in a power system to a larger extent than conventional power plants.

Coastal areas are increasingly being damaged with the expansion of seawater intrusion areas. We suggest a three-step method for reducing seawater intrusion areas by predicting future damage to groundwater being used continuously. First, the area most vulnerable to seawater intrusion damage is selected from among 25 areas on the west coast of the Republic of Korea. Having identified the Taean area as the region in question in the second step, we use RCP 4.5 and 8.5 as future sea level rise scenarios and predict the future usage of groundwater using linear-regression analysis of data for the past 10 years. Consequently, for RCP 8.5 (groundwater-usage scenario 1.0), 68.5% of the total Taean area is projected to be influenced by seawater intrusion. In the third step, the effectiveness of seawater intrusion reduction measures is analyzed considering the projected future situation and the local characteristics of the Taean area. After considering the effects of alternative locations, as well as seawater intrusion related data, alternatives were prioritized using a multi-criteria decision-making method. Consequently, 3, 5, and 4 were prioritized in the listed order, and we judged that by applying seawater intrusion area reduction measures according to this result, we will achieve the biggest effect.

As part of the efforts to reduce the environmental impacts caused by the aviation sector, the use of bio-based instead of fossil-based materials has been assessed as a possible mitigation option. Natural Fibre Polymer Composites have proven to have a higher environmental performance in the automotive sector and are emerging as an option for weight reduction in aircraft. This study quantifies, though Life Cycle Assessment, the environmental performance of specific flax-based composite panels intended for aircrafts as interior fitting elements (i.e. partition panels, tray tables, baggage compartments) compared to a glass fibre/epoxy composite with a honeycomb core. Through system expansion, the fate of co-products issued from the production of the flax fibre technical textile used as reinforcement in the biocomposite material were considered in the assessment. Results showed that for an application in the aeronautics sector, the weight of the panels is the upmost critical parameter shaping the overall environmental performance of panels. Focusing on the panel production only, the biocomposite panel showed a higher environmental performance in the categories of climate change and marine eutrophication compared to the conventional panel, and the fire suppressant agent was identified as the main contributor to the environmental impacts of the bio-based panel. Yet these gains were negligible when considering the full life cycle of the panels, due to the higher weight (14%) of the bio-based panels; which is linked to the bio-based panel being at a prototype stage.In order to improve the environmental performance of the biocomposite panel and thus reduce its weight, it was shown relevant to optimize geometry of the panel itself, especially its core, so less resin could be used.

In this article, management control has been studied from the perspective of intention towards sustainable development of companies. The main idea focuses on the analysis of relations between sustainable management control and the system of performance appraisal using as a reference the resource-based theory. These relations have been assessed both theoretically by reviewing literature in the field, and empirically based on data collected in a questionnaire from top management, as well as data from Annual Reports from the main segment of Bucharest Stock Exchange. The authors have shown that financial performance has a significant influence on management control, and the return on capital employed is one of the most recommended indicators. The sustainable nature attributed to management control is the result of institutional theory evolution, provisions of Directive 2014/95/EU and Guide of Global Management Accounting Principles (2015) using stewardship. Consequently, profits are not the main element any more in the assessment of financial „health” of a company. To ensure the sustainable success, sustainable balanced scorecard is one of real measures for managing financial and non-financial performance.

IntroductionThe aim of this study is to describe the epidemiology of all COVID-19 patients in Vietnam and to describe the measures of disease control and prevention implemented. MethodsData were recovered from Wikipedia regarding the 2020 coronavirus pandemic in Vietnam. The period covered was from 23 January to 20 April 2020. Descriptive analysis was stratified by gender, age, country of origin, travel history, clinical symptoms and outcome. A survey of disease control and prevention measures was conducted at the Centre for Disease Control in the Thai Binh province, which is responsible for screening and isolating individuals at high risk of COVID-19. ResultsAs of 20 April 2020, Vietnam had recorded 268 confirmed COVID-19 patients. 55.2% were female. 67.9% were aged 20-49 years and 82.5% were Vietnamese. 60.4% of cases were imported from outside Vietnam. Other cases were acquired in Vietnam by individuals in close contact with imported cases. Only one patient who had not travelled had had no known contact with a confirmed case. 63.1% of patients were asymptomatic. 75.7% of patients were discharged. No deaths were recorded. The Thai Binh CDC surveyed a total of 2,203 persons at risk of COVID-19. 336 persons (15.2%) were isolated at hospitals and 1,411 (64.0%) in dedicated isolation facilities. 16.4% reported at least one respiratory symptom. No positive cases confirmed by RT-PCR have been reported in the Thai Binh province to date. ConclusionThe effect of the systematic screening and isolation strategy made it possible to limit local transmission in Vietnam. Vietnam needs to reinforce diagnostic capacities, prevention measures and provide the necessary epidemiological data on which to base interventions. The wider use of rapid serological tests is also advisable in order to be able to conduct extensive screening in the community.

Hospital-acquired infections (HAIs) contribute to increased length of hospital stay, high mortality and higher health-care costs. Prevention and control of HAIs is a critical public health concern. We conducted a cross-sectional survey of 213 hospital health-care workers in Qassim, Saudi Arabia. We assessed Knowledge, Attitude and Practice (KAP) of standard infection control precautions using a structured questionnaire. Predictors of KAP were investigated using multivaraible logistic regression analyses and independent sample t tests. Prevalence of good (≥80% correct response) knowledge, attitude and practice were 67.6%, 61.5% and 73.2%, respectively. Predictors of good knowledge included age over 34 years (adjusted odds ratio: 30.5, p<0.001), and receiving training (13.3, p<0.001). Predictor of positive attitude was having >6 years of experience (5.5, p<0.001). While, the predictors of good practice were having >6 years of experience (2.9, p<0.01), previous exposure to HAIs (2.5, p<0.05) and training (3.5, p<0.01). However, being female (0.22, p<0.001) and older (>34 years) (0.34, p<0.01) were negatively associated with knowledge. Results indicate that older academic programs might not have adequately covered infection crontrol. Arranging training for HCWs might be useful in improving their knowledge of standard infection control precautions and is also expected to facilitate positive attitude and practice.

Exoskeleton robots are a rising technology in industrial contexts to assist humans in onerous applications. Mechanical and control design solutions are intensively investigated to achieve a high performance human-robot collaboration (e.g., transparency, ergonomics, safety, etc.). However, the most of the investigated solutions involve high-cost hardware, complex design solutions and standard actuation. In the presented work, an industrial exoskeleton for lifting and transportation of heavy parts is proposed. A low-cost mechanical design solution is proposed, exploiting compliant actuation at the shoulder joint to increase safety and transparency in human-robot cooperation. A hierarchic model-based controller is then proposed (including the modeling of the compliant actuator) to actively assist the human while executing the task. An inner optimal controller is proposed for trajectory tracking, while an outer fuzzy logic controller is proposed to online deform the task trajectory on the basis of the human’s intention of motion. A gain scheduler is also designed to calculate the optimal control gains on the basis of the performed trajectory. Simulations have been performed in order to validate the performance of the proposed device, showing promising results. The prototype is under realization.

This paper develops a novel energy universal service bus system (EUSBS) based on emerging energy Internet (E-net) technologies. This EUSBS is a unified identification and plug-and-play interface platform to which high penetration distributed energy and equipment (DEE), including photovoltaic (PV), fans, electric vehicle charging stations (EVCSs), energy storage equipment (ESE), and commercial and residential users (CRUs), can access in a coordinated control and optimized utilization mode. First, the functions design, overall framework and topology architecture design of the EUSBS are expounded, among which the EUSBS is mainly composed of a hardware system and a software platform. Moreover, several future application scenarios are presented. Then, the hardware part of EUSBS is designed and developed, including the framework design of this hardware subsystem, and development of the hardware equipment for PV access, fans access, EVCS access, ESE access, and CRU access. The hardware subsystem consists of smart socket, and household/floor/building concentrators. Based on this, the prototypes development of EUSBS hardware equipment is completely demonstrated. Third, the software part of the EUSBS is developed as a cloud service platform for electricity use data analysis of DEE. This software subsystem contains the power quality & energy efficiency analysis module, optimization control module, information and service module, and data monitoring and electricity behavior analysis module. Based on this design, the software interfaces are developed. Finally, an application study on energy management and optimization of a smart commercial building is conducted to evaluate the functions and practicality of this EUSBS. The EUSBS developed in this paper is able to overcome difficulties in big data collection and utilization on sides of distribution network and electricity utilization, and eventually implement a deep information-energy fusion and a friendly supply-demand interaction between the grid and users. This contribution presents a detailed and systematic development scheme of the EUSBS, and moreover, the laboratory prototypes of the hardware and software subsystems have been developed based on E-net technologies. This paper can provide some thoughts and suggestions for the research of active distribution network and comprehensive energy management and optimization in power systems, as well as references and guidance for researchers to carry out research regarding energy management, optimization and coordinated control of the smart buildings.

There is a continuous growth of heat pump installations in residential buildings in Germany. The heat pumps were not only used for space heating and domestic hot water consumption but also to offer flexibility to the grid. the high coefficient of performance and the low cost of heat storages made the heat pumps an optimal candidate for the power to heat applications. Thus, several questions are raised about the optimal integration and control of the heat pump system with buffer storages to maximize its operation efficiency and minimize the operation costs. In this paper, an experimental investigation is performed to study the performance of a ground source heat pump (GSHP) with a combi-storage under several configurations and control factors. The experiments were performed on an innovative modular testbed that is capable of emulating a ground source to provide the heat pump with different temperature levels at different times of the day. Moreover, it can emulate the different building loads such as the space heating load and the domestic hot water consumption in real-time. The data gathered from the testbed and different experimental studies were used to develop a simulation model based on Modelica that can accurately simulate the dynamics of a GSHP in a building. The model was validated based on different metrics. Energetically, the difference between the developed model and the measured values was only 3.08\% and 4.18\% for the heat generation and electricity consumption, respectively.

In this study we investigated the potential of two non-edible oil extracts from seeds of Colliguaya Integerrima (CIO) and Colliguaja Salicifolia (CSO) to use as a renewable source for polyols and eventually polyurethane foams or biodiesel. For this purpose, two novel polyols from the aforementioned oils were obtained in a one-single step reaction using a mixture of hydrogen peroxide and acetic acid. The polyol derivatives obtained from the two studied oils were characterized by spectral (FT-IR, ¹H NMR and ¹³C NMR), physico-chemical (e.g. chromatographic analysis, acid value, oxidizability values, iodine value, peroxide value, saponification number, kinematic viscosity, theorical molecular weights, density, hydroxyl number and hydroxyl functionality) and thermal (TGA) analyses according to standard methods. Physico-chemical results revealed that all parameters, with the exception of the iodine value, were higher for bio-polyols (CSP and CIP polyols) compared to the starting oils. The NMR, TGA and FT-IR analyses demonstrated the formation of polyols. Finally, the OH functionality values for CIP and CSP polyols were 4.50 and 5.00, respectively. This result indicated the possible used of CIP and CSP polyols as a raw material for the preparation of polyurethane rigid foams.

Cyber-Physical Systems (CPS) are integrations of computation and physical processes. Physical processes are monitored and controlled by embedded computers and networks, which frequently have feedback loops where physical processes affect computations and vice versa. To ease the analysis of a system, the costly physical plants can be replaced by high-fidelity virtual models that provide a framework for Digital-Twins (DT). This paper aims to briefly review the state-of-the-art and recent developments in DT and CPS. Three main components in CPS, including communication, control, and computation, are reviewed. Besides, the main tools and methodologies required for implementing practical DT are discussed by following the main applications of DT in the fourth industrial revolution through aspects of smart manufacturing, sixth wireless generation (6G), health, production, energy, and so on. Finally, the main limitations and ideas for future remarks are talked about followed by a short guideline for real-world application of DT towards CPS.

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser-wire based Directed Energy Deposition is demonstrated with a novel modification: site-specific changes to the controller set-point were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary 3D-printed component geometry. The present work shows that, through this technique, it is possible to print a specific geometry that occurs beyond the actual toolpath of the print head. This is denoted as an extra-toolpath geometry and is fundamentally different from other methods of generating component features in metal AM. A proof-of-principle experiment is presented in which a complex oak leaf geometry was embossed on an otherwise ordinary double-bead wall made from Ti-6Al-4V. The process is introduced and characterized primarily from a controls perspective with reports on the performance of the control system, the melt pool size response, and the resulting geometry. The implications of this capability, which extend beyond localized control of bead geometry to the potential mitigations of defects and functional grading of component properties, are discussed.

In this paper, a mathematical model of breast cancer governed by a system of ordinary differential equations in the presence of chemotherapy treatment and ketogenic diet is discussed. Several comprehensive mathematical analysis was carried out using varieties of analytical methods to study the stability of the breast cancer model. Also, sufficient conditions on parameter values to ensure cancer persistence in the absence of anti-cancer drugs ketogenic diet and cancer emission when anti-cancer drugs, immune-booster, ketogenic diet are included were established. Furthermore, optimal control theory is applied to find out the optimal drug adjustment as an input control of the system therapies to minimize the number of cancerous cells by considering different controlled combinations of administering the chemotherapy agent and ketogenic diet using the popular Pontryagin’s Maximum Principle. Numerical simulations were presented to validate our theoretical results.

The main objective of this paper is to continue the development of activities of basic and applied research related to wind energy and to develop methods of optimal control to improve the performance and production of electrical energy from wind. A new control technique of Double fed induction generator for wind turbine is undertaken through a robust approach tagged nonlinear sliding mode control (SMC) with exponential reaching law control (ERL). The SMC with ERL proves to be capable of reducing the system chattering phenomenon as well as accelerating the approaching process. A nonlinear case numerical simulation test is employed to verify the superior performance of the ERL method over traditional power rate reaching strategy. Results obtained in Matlab/Simulink environment show that the SMC with ERL is more robust, prove excellent performance for the control unit by improving power quality and stability of wind turbine.

We present a generalized state-space model formulation particularly motivated by an online scheduling perspective. Through these proposed generalizations, we enable a natural way to handle routinely encountered disturbances and a rich set of corresponding counter-decisions. Thereby, greatly simplifying and extending the possible application of mathematical programming based online scheduling solutions to diverse application settings.

This paper introduces a closed-loop control strategy for maintaining consistency of liquid temperature in commercial Drop on Demand (DoD) inkjet printing. No additional sensors or additional actuators are installed in the printhead while achieving the consistency in liquid temperature. To this end, this paper presents a novel in situ sensing-actuation policy at every individual liquid-nozzle, where the jetting mechanism has three distinct roles. It is used for jetting liquid droplet onto the print media based on the print-job. It is used as a soft sensor to estimate the real-time liquid temperature of the jetting nozzle. While not jetting liquid, it is used as a heating actuator to minimize the gradient of liquid temperature among nozzles. The soft sensing based in situ controller is implemented in an experimentally validated digital twin that models the thermo-fluidic processes of the printhead. The digital twin is scalable and flexible to incorporate an arbitrary number of liquid-nozzles, making the control strategy applicable for future designs of the printhead.

The high dimensions and governing non linear dynamics in wind farm systems make the design of numerical optimal controllers computationally expensive. A possible pathway to circumvent this challenge lies in finding reduced order models which can accurately embed the existing non linearities. The work here presented applies the ideas motivated by non linear dynamical systems theory - the Koopman Operator - to an innovative algorithm in the context of wind farm systems - Input Output Dynamic Mode Decomposition - to improve on the ability to model the aerodynamic interaction between wind turbines in a wind farm and uncover insights into the existing dynamics. It is shown that a reduced order linear state space model can reproduce the downstream turbine generator power dynamics and reconstruct the upstream turbine wake. It is further shown that the fit can be improved by judiciously choosing the Koopman observables used in the IODMD algorithm without jeopardizing the models ability to rebuild the turbine wake. The extensions to the IODMD algorithm provide an important step towards the design of linear reduced order models which can accurately reproduce the dynamics in a wind farm.

Promoter is a small region of DNA sequence in response to various transcription factors, which initiates a particular gene expression. The promoter-engineered bio-sensor can activate or repress gene expression through transcription factor recognizing specific molecules, such as polyamine, sugars, lactams, amino acids, organic acids or redox molecule, however, the reported applications of promoter enhanced bio-sensor are not too much. This review paper highlights the strategies of construction of promoter-gene engineered bio-sensor with human and bacteria’s genetic promoter array for high-throughput screening (HTS) molecular drugs, study of membrane protein’s localization and nucleocytoplasmic shuttling mechanism of regulating factor, enzyme activity, detection of the toxicity of intermediate chemicals, and probing bacteria density to improve value-added product titer. These bio-sensors’s sensitivity and specificity can be further improved by proposed approaches of Mn²⁺ and Mg²⁺ added random Error-prone PCR and site-directed mutagenesis which is applied for construction of bacteria’s “mutant library”. It is expected to establish flexible HTS platform (Bio-sensor array) to large-scale screen transcription factor-acting drugs, reducing the toxicity of intermediate compounds, and constructing gene dynamic regulatory system in “push and pull” mode to effectively regulate the valuable medicinal product production. This proposed novel promoter-engineered biosensors aided synthetic genetic circuit construction will maximize the efficiency of bio-synthesis of medicinal compound, which will greatly promote the development of microbial metabolic engineering and biomedical science.

Reciprocal Personal/Public Protection (RPPP) featured with source control is introduced, Mask Discriminating Mouth and Nose (MDMN) is employed to serve the purpose, which includes polymer based mouth cover with optional nose cover. The new knowledge that mouth is a primary, active and dominant source of the virus has been well established, which is the base of MDMN. Source classification and related source control tools are discussed, mouth cover is recommended as the tool prioritized to use. Liquid droplets is identified as a hard issue related to mask, liquid droplets, mask fitting, comfort and facial recognition constitute real challenges of mask in addition to efficiency, All of these have been addressed with MDMN. Comparisons between MDMN and masks/face covering are taken on four aspects: efficiency and efficacy, tolerance and comfort, cost and waste, and civil rights and public interest. Mouth cover is recommended to replace the face covering and act as both a personal tool and a public utensil, mouth cover with nose cover can provide better protection than N95 etc. RPPP with MDMN, could be an alternative for lockdown, a parallel strategy to vaccine, and a collectively living way during the pandemic era. MDMN, featured with high efficiency protection, high degree comfort, easy wearing, tight-fitting, easy facial recognition & communication, reusability, cost-effective, environment friendly and scale manufacturing more readily and widely etc., is a simple and sustainable solution, which is essential for ordinary people to keep wearing it properly for protection.

The bio-oil obtained by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 ºC, 1.0 atmosphere, in technical scale, submitted to fractional distillation to produce biofuels-like fractions. The distillation of bio-oil carried out in a laboratory distillation column (Vigreux) of 30 cm. The physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) determined by official methods. The chemical functions present in distillation fractions determined by FT-IR and the chemical composition by GC-MS. The distillation of bio-oil yielded gasoline, light kerosene, and kerosene-like fuel fractions of 16.16, 19.56, and 41.89% (wt.), respectively. All the physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) increase with boiling temperature. The gasoline-like fraction is composed by 64.0% (area.) hydrocarbons and 36.0% (area.) oxygenates, while light kerosene-like fraction by 66.67% (area.) hydrocarbons and 33.33% (area.) oxygenates, and kerosene-like fraction by 19.87% (area.) hydrocarbons and 81.13% (area.) oxygenates.

Few switching transitions in high power and medium voltage application of Power converters are desirable. The selective harmonics elimination (SHE) pulse width modulation offers a better quality waveform with lower switching transitions and hence lower switching losses. The SHE is a pre-programmed modulation technique where certain amounts of lower order harmonics are removed and fundamental voltage is controlled. After Fourier analysis of output waveform, a set of nonlinear transcendental equations is obtained which exhibits, multiple, unique or no solution in different range of modulation index (MI). In this paper, an iterative method based on the Jacobian estimate is proposed to solve a highly non-linear set of SHE equations. The proposed technique is easy in implementation and can solve a large number of such equations as computation of the Jacobian matrix in the subsequent iteration is estimated from the previous values. Moreover, the proposed method also removes the singularity problem, especially for large SHE equations. High accuracy in the initial guess is also not essential for this method and can converge to the solution with any random initial guess. The computational and simulation results are given to validate the concept. The hardware result is provided to confirm the computational and simulation results.

Methanol is a natural ingredient with major occurrence in fruit spirits, such as apple, pear, plum or cherry spirits, but also in spirits made from coffee pulp. The compound is formed during fermentation and the following mash storage by enzymatic hydrolysis of naturally present pectins. Methanol is toxic above certain threshold levels and legal limits have been set in most jurisdictions. Therefore, the methanol content needs to be mitigated and its level must be controlled. This article will review the several factors that influence the methanol content including the pH value of the mash, the addition of various yeast and enzyme preparations, fermentation temperature, mash storage, and most importantly the raw material quality and hygiene. From all these mitigation possibilities, lowering the pH value and the use of cultured yeasts when mashing fruit substances is already common as best practice today. Also a controlled yeast fermentation at acidic pH facilitates not only reduced methanol formation, but ultimately also leads to quality benefits of the distillate. Special care has to be observed in the case of spirits made from coffee by-products which are prone to spoilage with very high methanol contents reported in past studies.

Satellites are subject to various severe vibration during different phases of flight. The concept of satellite smart adapter is proposed in this study to achieve active vibration control of launch vehicle on satellite. The satellite smart adapter has 18 active struts in which the middle section of each strut is made of piezoelectric stack actuator. Comprehensive conceptual design of the satellite smart adapter is presented to indicate the design parameters, requirements and philosophy applied which are based on the reliability and durability criterions to ensure successful functionality of the proposed system. The coupled electromechanical virtual work equation for the piezoelectric stack actuator in each active strut is drived by applying D'Alembert's principle. Modal analysis is performed to characterize the inherent properties of the smart adapter and extraction of a mathematical model of the system. Active vibration control analysis was conducted using fuzzy logic control with triangular membership functions and acceleration feedback. The control results conclude that the proposed satellite smart adapter configuration which benefits from piezoelectric stack actuator as elements of its 18 active struts has high strength and shows excellent robustness and effectiveness in vibration suppression of launch vehicle on satellite.

Background: Outbreak of the Covid-19 is now an ongoing global health emergency. At the end of December 2019, the first infection was reported in Wuhan and the world did not pay attention to this extremely contaminated disease and plucked to react rapidly. The World is in an vulnerable state in disease spreading, facing a great loss of lives and socio-economic aspects also. That is why we have proposed a potential mathematical model with data analysis to predict and control the outcome of this pandemic. Methods: The model presented the epidemic dynamics of multiple compartments. We collected available online data of Spain. In primary step, we estimated the parameters using either the data analysis or reference papers. Then we did the data fitting analysis in comparison with the outcome of our mathematical results. The results of the system depended not only the parameters also on social consciousness. Results: It is found that disease progression in this model is determined by the basic reproductive ratio, $R_0$, the actual epidemic of $R_0$ and effective $R(t)$ of each day. If $R_0>1$, the number of latently infected individuals grows exponentially; endemic solution is stable while infection rate decays if $R_0<1$. The optimal control theory stated that vaccination and treatment strategies are highly effective for reducing both susceptible and infected population and to increase the recover rate high. In Spain, after state of alarm (quarantine) on 14 March 2020, reported cases increasing for 13 days only and from the 14th day, daily reported cases started to decline albeit with small fluctuation. Our proposed model approximates that the disease in Spain could be fully under control by after July 2020. Conclusion: Outbreak will be in control of health care system, reduce the death rate and will ensure social-economic stability.

This article presents a decentralized phase-shedding technique for multiphase converters. The usual central digital controller is replaced by identical local controllers forming a daisy-chain structure. Phase-shedding decisions are taken locally based on a local inductor current monitoring and threshold crossing management. This control strategy allows to implement as many phases as desired in a modular manner. In order to handle specific events such as load current inrush or a start-up sequence and to guarantee optimal transient responses, additional functions are included into each local controllers. The inter-cell communication protocol is described, along with necessary design considerations of threshold and timing values. Finally, functional simulations are carried out on a 5-leg 12V/1.2V 60W multiphase converter, which validate the proposed decentralized phase-shedding strategy for a microcontroller power supply implementation.

The log interpretation and evaluation of Chang 8 tight sandstone reservoir in Longdong West area, Ordos Basin, is facing great challenges due to the existence of low resistivity contrast oil pays. To better guide the exploration of oil resources in this area, the characteristics and control mechanism of low resistivity contrast oil pays were studied in this research. Firstly, according to the relative value of apparent resistivity increase rate of the target formation, the reservoir was divided into two types: low resistivity contrast oil pay (LRCP) and high resistivity oil pay (HRP). Then, the reservoir characteristics were studied by comparing and analyzing the experimental data, formation water data and logging data collected from the two reservoir types. On this basis, the control mechanism of LRCP was studied and summarized into reservoir micro factors and regional macro factors, respectively. It is found that the reservoir rock composition between LRCP and HRP is basically the same. Compared with HRP reservoir, the average porosity and permeability of LRCP reservoir are relatively better, but the pore structure is relatively poorer because of the high content of micro pores. When the filling pressure of crude oil is sufficient enough, the high oil saturation can be formed in LRCP reservoir. The high irreducible water saturation and high formation water salinity are the main micro factors reduced the reservoir resistivity. Besides, the difference of hydrocarbon expulsion capacity of source rock and the regional difference of formation water salinity are the macro factors influenced the distribution of LRCP and HRP from vertical and horizontal of the region. The formation of LRCP is controlled by the comprehensive influence of reservoir micro factors and regional macro factors. And the comprehensive consideration of the influence of micro factors and macro factors on LRCP is suggested during the log interpretation and evaluation.

In this paper, optimum parameters of Tuned Mass Dampers (TMD) are considered to control the responses of 10-story shear building under harmonic loading and 22 set of seismic records of FEMA-P695. The criterion used to obtain the optimum parameters is to select mass ratio, the frequency (tuning) and damping ratio that would result in smallest lateral displacements. State-space equations of motion are presented to compute the structural responses by developing a MATLAB file. A 10-story shear building is presented as a case study to assess the effects of TMDs on the multi-story structures. The results indicate that using TMD can reduce structural responses up to the average 20% under earthquake excitation and up to 90% under harmonic loadings. TMDs are not always effective under any type of ground motion; therefore, being aware of the given location is significant to design TMDs properly.

Rice is the grain feeds more than half of the world population. It is an important staple food provides twenty percent of the calories consumed worldwide. Food safety affects the health of consumers. Establishing an effective traceability system is one of the primary measures to protect rice quality and food safety. Blockchain-based traceability system has the characteristics of data tamper-proofing, decentralization, and co-governance. This paper proposed a rice traceability scheme based on blockchain technology that selects the critical nodes in the rice industry chain to construct a blockchain network to achieve transparent data sharing. It is meaningful for both enterprises and consumers. It can let enterprises get the real quality information of rice and related raw materials. Consumers can get the true information of rice and rice products to buy safe and healthy food. The scheme is proved feasible by simulating the traceability of the rice supply chain.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

This study examines the relationship of fear of missing out (FOMO) with heavy social networking among Turkish university students (aged 17 - 55). The perception of the possible role of parental supervision on online activities is also investigated. Factor analysis of FOMO scale led us to evaluate the construct under two dimensions as (1) fear of missing experience and (2) fear of missing activity. The results revealed that fear of missing activity increases social media intrusion while fear of missing experience is found to have no significant effect. The reverse relationship is also valid: an urge to use social media predicts fear of missing out (activity and experience). Fear of missing experience is associated with problematic social media use (PSMU) and a high desire to use social media. The results additionally demonstrate that students aged 30 and older believe more in the requirement of parental control than those aged 17-22.

Battery/Supercapacitor(SC) current tracking control is a key issue for hybrid energy storage system (HESS) in electric vehicles. An innovative passivity-based L2-gain adaptive control (PBL2AC) based on port-controlled Hamiltonian model with dissipativity (PCHD) for reference current tracking and bus voltage stability in HESS is presented. The developed PCHD model has considered both parameter variations and external disturbances. By using L2-gain disturbance attenuation, the PBL2AC ensures robust reference current tracking and stable bus voltage. Moreover, adaptive mechanism is adopted to estimate the electrical parameters. To validate the proposed control scheme for HESS, simulations and experiments were done and compared with traditional PID and sliding mode control under several typical driving cycles, and results show that the effectiveness of the proposed controller can be confirmed.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

Graphene oxide (GO), nanographene oxide (nGO) and partially reduced graphene oxide (rGO) have been studied as possible foam stabilizing agents for CO₂ based enhanced oil recovery (EOR). GO was able to stabilize CO₂/synthetic sea water foams. rGO was not able to stabilize foams likely due to the high reduction degree of the material. Particle size had a strong influence on foamability and stability. GO hydrophilicity increased as the particle size decreased and no foams were created when particle size was below 1 µm (nGO). GO brine dispersions showed immediate gel formation, which improved foam stability. Particle growth due to layer stacking was also observed. This mechanism was detrimental for foam formation and stabilization. nGO dispersed in synthetic sea water rapidly formed hydrogels and was not filterable. This work indicates that the particles studied are not suitable for CO₂ EOR purposes.

Merchant marine fleet is under inspections by several parties to ensure maritime regulation compliance. One of the major effects on implementation of regulations by International Maritime Organization (IMO) is indeed Port State Control. This article aims to analyze Paris Memoranda of Understanding (MOU) all detention remarks from 2013 to 2019 for EU15 countries (except Luxemburg and Austria) through an approach based on Analytical Hierarchy Process and demonstrate the results on Geographic Information System (GIS) to guide marine industry on detainable Port State Control remarks and country risk profile. While Analytical Hierarchy Process Approach has been used to indicate the ranking of basic maritime regulations from the perspective of the port state control , GIS help us to demonstrate the regional dispersion amongst EU15. The data of the detained vessel taken from the public website of Paris MOU and each report considered as a professional judgement that causes detention. It has been shown that almost all countries top priorities for regulation are Safety of Life at Sea (SOLAS) and Fire Safety Systems (FSS). Consequently, the results of the study can assist Port State Officers, ship crew, ship owners and managers presenting the facts of their inspection and able to improve themselves. The spatial analysis also expected to guide ship owners and managers to focus their vessel’s deficiencies to prevent sub-standardization.

The use of wind energy has been developing fast over the last years. The global cumulative wind power capacity increased by 10.5% in 2019, most of which comes from onshore wind farms. One of the consequences of this continuous increase is the use of land for onshore wind farms. There are already cases worldwide where lack of well-established plans and strategies have caused delays in projects. The need for efficiently using land for wind farms will be mandatory in the short term. In this work, we present a numerical analysis to evaluate wind farm land-use. By defining the ratio between mechanical output power over an area as a parameter called land-use ratio, this work focused on comparing several cases of aligned and staggered layouts. Mechanical output power was estimated using a validated code based on Blade Element Momentum code, and the wake velocities and wake interaction effects were estimated using a validated wind turbine CFD model. In terms of output power, staggered designs are more efficient than aligned designs. However, the results showed that even though staggered designs produced higher output power, aligned farms with tight lateral spacing could be as efficient as staggered ones in terms of land-use but using fewer turbines. In summary, tightly aligned designs should be a tendency in the future towards efficient use of land in wind farms.

The risk of 'zoonotic spillovers,' or the transmission of viruses from animals to humans, has been raised by climate change and the devastation of nature, as infectious disease experts have long warned. Even as the world works to stop the spread of the currently unfolding pandemic of coronavirus disease 2019 (COVID-19) and the breakout of monkeypox virus (MPXV), a new animal virus, the Langya henipavirus (LayV), has been discovered in humans in Eastern China. The scientists say there is little danger of the virus spreading among humans, but it shares genetic material with Hendra virus and Nipah virus, two other henipaviruses that infect humans and cause life-threatening respiratory diseases. Humans infected with LayV can expect to experience high body temperature, cough, weariness, poor appetite, muscle discomfort, myalgia, nausea and vomiting. It is likely that the virus will spread from animals to humans. Currently, the health authorities of Taiwan and other health organizations are tracking the progress of the ailment to ensure it does not reach humans. Researchers have examined 25 species of small wild animals for presence of the virus, and so far, shrews are the only ones that have tested positive for the virus's RNA. Based on these results, shrews are a possible candidate for the virus's natural reservoir. Too far, no therapies or vaccines have been developed and licensed for henipaviruses like the LayV. When other therapies fail to alleviate viral infections, ribavirin may be the next best thing. The need for novel vaccinations against the LayV infection and the timely delivery of these vaccines to areas at high epidemiological risk is real. To lessen the likelihood of a health calamity being caused by this newly developing virus, it is crucial to conduct active surveillance in a transparent and globally collaborative manner. The questions that have not been answered yet require additional study.

Due to legal regulations, the rise of globalised (online) commerce and the need for public health protection, the analysis of spirits (alcoholic beverages &gt; 15 % vol) is a task with growing importance for governmental and commercial laboratories. In this article a newly developed method using nuclear magnetic resonance (NMR) spectroscopy for the simultaneous determination of 15 substances relevant for the quality and authenticity assessment of spirits is described. The new method starts with a simple and rapid sample preparation and does not need an internal standard. For each sample a group of 1H-NMR spectra is recorded, among them a 2D spectrum for analyte identification and 1D spectra with suppression of solvent signals for quantification. Using the Pulse Length Based Concentration Determination (PULCON) method, concentrations are calculated from curve fits of the characteristic signals for each analyte. The optimisation of the spectra, their evaluation and the transfer of the results are done fully automatically. Glucose, fructose, sucrose, acetic acid, citric acid, formic acid, ethyl acetate, ethyl lactate, acetaldehyde, ethanol, methanol, n-propanol, isobutanol, isopentanol, 2-phenylethanol and 5-(hydroxymethyl)furfural (HMF) can be quantified with an overall accuracy better than 8 %. This new NMR-based targeted quantification method enables the simultaneous and efficient quantification of relevant spirits ingredients in their typical concentration ranges in one process with good accuracy. It has proven to be a reliable method for all kinds of spirits in routine food control.

In this paper we investigate the optimal investment strategy for a defined contribution (DC) pension plan during the decumulation phrase which is risk-averse and pays close attention to inflation risk. The plan aims to maximize the expected constant relative risk aversion (CRRA) utility from the terminal wealth by investing the wealth in a financial market consisting of an inflation-indexed bond, an ordinary zero coupon bond and a risk-free asset. We derive the optimal investment strategy in closed-form using the dynamic programming approach by solving the corresponding Hamilton-Jacobi-Bellman (HJB) equation. Our theoretical and numerical results reveal that under some rational assumptions, an inflation-indexed bond do has significant advantage to hedge inflation risk.

The paper interprets a comparison of two mostly used techniques of a field-oriented control for 6-phase electric drives, with their pros and cons, as well as their differences in construction and behaviour. Both of these approaches have been realized. Frequency and step responses analysis have been demonstrated with a 6-phase permanent magnet synchronous machine. Experimental results have been compared with simulations based on a mathematical model.

Machine learning (ML) is penetrating in all walks of life and is one of the major driving forces behind the fourth industrial revolution, typically known as Industry 4.0. This study reviews the state-of-the-art ML applications in the biofuels’ life cycle stages, i.e., soil, feedstock, production, consumption, and emissions. A keyword search is performed to retrieve relevant articles from the databases of the Web of Science and Google Scholar. ML applications in the soil stage were mostly based on the use of satellite images of land for estimation of biofuels yield or suitability analysis of agricultural land. In the second stage of the life cycle, assessment of rheological properties of the feedstocks and their effect on the quality of biofuels were dominant studies reported in the literature. The production stage included estimation and optimization of quality, quantity, and process conditions. The fuel consumption and emissions stage included analysis of engine performance and estimation of emissions temperature and composition, such as NOx, CO, and CO2. This study identified the following trends: dominant ML method, the stage of life cycle getting more usage of ML, the type of data used for the development of the ML-based models, and the stage-wise frequently used input and output variables. The findings of this article are beneficial for academia and industry-related people involved in model development in different stages of biofuel’s life cycle.

This paper reports a new control strategy to improve sharing of unbalanced currents in islanded LV microgrids. This technique provides fast and effective sharing of positive-, negative- and zero-sequence currents, and is the first example of zero-sequence current sharing in the literature. The controllers are designed in the stationary frame. The control structure consists of four loops; 1)~the current controller; 2)~the voltage controller; 3)~the droop controller and the 4)~negative and zero sequence current controllers. The output current is considered unknown for the controller and is added to the control system as a disturbance. The proposed controller features a high gain in fundamental and harmonic frequencies, hence a good voltage quality is obtained in the presence of unbalanced and nonlinear loads. To this aim, a proportional-resonant (PR) controller is adopted as the current controller. By using a multi-resonant controller as current controller, a unified control structure is obtained which is suitable for both grid-connected and islanded modes. The voltage controller is designed using a resonant controller so that the voltage can have low VUF and THD in the presence of unbalanced and nonlinear loads. Furthermore, in this paper droop method is applied to the control structure to share real and reactive powers. Simulation studies show that the conventional droop method cannot share the oscillatory part of the output power that is due to the presence of unbalanced loads in the microgrid. This paper relies on using zero and negative sequence virtual impedance controller to share the oscillatory part of output power. By using zero-sequence virtual impedance controller (ZSVIC) and negative-sequence virtual impedance controller (NSVIC), the zero and negative sequence currents in the microgrid are controlled and shared effectively. By compensating zero- and negative-sequence currents locally, the flow of these currents in the microgrid is minimized, and the overall power quality of the islanded LV microgrid is improved.

The new emergence and re-emergence of arbovirus infections vectored by Aedes mosquitoes have been spread across Southeast Asia, Central Africa, United States, tropical Oceania and become a major of public health concerns. These arbovirus diseases found to have a similar vector, symptoms of the diseases and environments. The situation has become complicated without any specific vaccine or treatment for the diseases. As far as we concern, vector control is the best defense with many challenges, a scattered breeding site and biological behavioral sometimes, more difficult to control. Herein, we present a review of studies on current techniques proposed to combat arbovirus infections vectored by Aedes mosquitoes. A crucial gap in a vector control program is the inability to eliminate and destroy the cryptic breeding site by using conventional control methods. The idea and proper concept of using mosquitoes to bring insecticide to their oviposition site had been getting more interest in people to explore. Autodissemination is a self-delivery technique by manipulating the behavior of mosquitoes, carrying the insecticide and disseminate to cryptic breeding sites. This technique has shown a promising result in some countries and can be considered as additional tools in a vector control program

Emerging and reemerging pathogens is a global challenge for public health. Recently, a novel coronavirus disease emerged in Wuhan, Hubei province of China, in December 2019. It is named COVID-19 by World Health Organization (WHO). It is known to be caused by Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) that affects the lower respiratory tract and manifests as pneumonia in humans. Coronaviruses (CoVs) are structurally more complicated as compared to other RNA viruses. This viral epidemic has led to the deaths of many, including the elderly or those with chronic disease or compromised immunity. Viruses cause infection and diseases in humans of varying degrees, upper respiratory tract infections (URTIs) cause common cold while lower respiratory tract infections induce pneumonia, bronchitis, and even severe acute respiratory syndrome (SARS). The costs of COVID-19 are not limited. It equally affects all the medical, sociological, psychological, and economic aspects globally. This is regarded as the third deadly outbreak in the last two decades after Severe Acute Respiratory Syndrome SARS (2002–2003) and Middle East Respiratory Syndrome MERS (2012). Based on the sequence homology of SARS-CoV-2, different animal sources including bats, snakes, and pangolins have been reported as potential carriers of this viral strain. Real-time RT-PCR represents the primary method for the diagnosis of new emerging viral strain SARS-CoV-2. The transmission dynamics suggest that SARS-CoV-2 is transmitted from person-to-person through direct contact or coughing, sneezing, and by respiratory droplets. Several anti-viral treatments including lopinavir/ritonavir, remdesivir, chloroquine phosphate, and abidor are also suggested with different recommendations and prescriptions. Protective and preventive strategies as suggested by various health organization i.e. WHO and US Center for Disease Control and Prevention (CDC) must be adopted by everyone. This review covers the important aspects of novel COVID-19 including characteristics, virology, symptoms, diagnostics, clinical aspects, transmission dynamics, and protective measures of COVID-19.

Abstract: The promotion of sustainable packaging is part of the European Green Deal and plays a key role in the EU’s social and political strategy. One option is the use of renewable resources and biomass waste as raw materials for polymer production. Lignocellulose biomass from annual and perennial industrial crops and agricultural residues are a major source of polysaccharides, proteins, and lignin, and can also be used to obtain plant-based extracts and essential oils. Therefore, these biomasses are considered as potential substitute for fossil-based resources. Here, the status quo of bio-based polymers is discussed and evaluated in terms of properties related to packaging applications such as gas and water vapor permeability as well as mechanical properties. So far, their practical use is still restricted due to lower performance in fundamental packaging functions that directly influence food quality and safety, the length of shelf life and thus the amount of food waste. Besides bio-based polymers, this review focuses on plant extracts as active packaging agents. Incorporating extracts of herbs, flowers, trees, and their fruits is inevitable to achieve desired material properties that are capable to prolong the food shelf life. Finally, the adoption potential of packaging based on polymers from renewable resources is discussed from a bioeconomy perspective.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

This paper focuses on the integrated guidance and autopilot design with control input saturation in the end-game phase of hypersonic flight. Firstly, uncertain nonlinear integrated guidance and autopilot model is developed with third actuator dynamics, where the control surface deflection has magnitude constraint. Secondly, neural network is implemented in extended state observer (ESO) design, which is used to estimate the complex model uncertainty, nonlinearity and state coupling. Thirdly, a command filtered back-stepping controller is designed with hybrid sliding surfaces to improve the terminal performance. In the process, different command filters are implemented to avoid the influences of disturbances and repetitive derivation, meanwhile solve the problem of unknown control direction caused by saturation. The stability of closed-loop system is proved by Lyapunov theory, and the principles abided by the controller parameters are concluded through the proof. Finally, series of 6-DOF numerical simulations are presented to show the feasibility and validity of the proposed controller.

Background: SARS-CoV-2 has resulted in a global pandemic, COVID-19. The disease has spread outrageously from Wuhan, china to rest of the world affecting millions of people. The human transmission is mainly known to occur by aerosols. As almost every dental procedure is associated with aerosol production, oral health care professionals are at a high risk of getting the infection. An attempt has been made to render cohesive practical suggestions for dental professionals amid COVID-19 outbreak. Objectives: The paper aims at providing evidence based information in managing dental patients during this pandemic. Material and Methods: The paper provides a broad overview of predominant findings based on electronic database search regarding COVID-19 outbreak and its effect on dental practice. Conclusion: Dental care should not be neglected due to the pandemic. Thorough knowledge about the disease and its prevention will not only help us in providing care to these patients but will also help in preventing the nosocomial spread of infection.

A real-time two-way direct load control (TWDLC) of central air-conditioning chillers in wide area is proposed to provide demand response. The proposed TWDLC scheme is designed to optimize the load shedding ratio of every customer under control to ensure the target load to be shed is met at every scheduling period. In order to overcome the load reduction uncertainties of TWDLC, an innovative solution is proposed by applying a certain degree of loosening on the constraint of the actual shed load. Fuzzy linear programming is utilized to solve the optimization problem with fuzzy constraints. The proposed fuzzy linear programming problem is solved by delicately transforming it into a regular liner programming problem. A selection scheme used to obtain the feasible candidates set for load shedding at every sampling interval of TWDLC is also designed along with the fuzzy linear programming.

This work deals with the numerical investigation of the delivery of potential therapeutic agents through dentinal discs (i.e. a cylindrical segment of the dentinal tissue) towards the dentin-pulp junction. The aim is to assess the main key features (i.e. molecular size, initial concentration, consumption rate, disc porosity and thickness) that affect the delivery of therapeutic substances to the dental pulp and consequently to define the necessary quantitative and qualitative issues related to a specific agent before its potential application in clinical practice. The CFD code used for the computational study is validated with relevant experimental data obtained using micro Laser Induced Fluorescence (μ-LIF) a non-intrusive optical measuring technique. As the phenomenon is diffusion dominated and strongly dependent on the molecular size, the time needed for the concentration of released molecules to attain a required value can be controlled by their initial concentration. Finally, a model is proposed which, given the maximum acceptable time for the drug concentration to attain a required value at the pulpal side of the tissue along with the aforementioned key design parameters, is able to estimate the initial concentration to be imposed and vice versa.

The increasing variability in power plant load, in response to a wildly uncertain electricity market and the need to to mitigate CO₂ emissions, lead power plant operators to explore advanced options for efficiency optimization. Model-based, system-scale dynamic simulation and optimization are useful tools in this effort, and the subject of the work presented here. In prior work, a dynamic model validated against steady-state data from a 605 MW subcritical power plant was presented. This power plant model is used as a test-bed for dynamic simulations, in which the coal load is regulated to satisfy a varying power demand. Plant-level control regulates plant load to match an anticipated trajectory of the power demand. The efficiency of the power plant operating at varying load is optimized through a supervisory control architecture that performs set point optimization on the regulatory controllers. Dynamic optimization problems are formulated to search for optimal time-varying input trajectories that satisfy operability and safety constraints during the transition between plant states. An improvement in time-averaged efficiency of up to 1.8% points is shown feasible with corresponding savings in coal consumption of 184.8 tons/day and carbon footprint decrease of 0.035 kg/kWh.

Exercise facilitates weight control, partly through effects on appetite regulation. Single bouts of exercise induce a short-term energy deficit without stimulating compensatory effects on appetite, whilst limited evidence suggests that exercise training may modify subjective and homeostatic mediators of appetite in directions associated with enhanced meal-induced satiety. However, large variability in responses exists between individuals. This article reviews the evidence relating to how adiposity, sex and habitual physical activity modulate exercise-induced appetite, energy intake and appetite-related hormone responses. The balance of evidence suggests that adiposity and sex do not modify appetite or energy intake responses to acute or chronic exercise interventions, but individuals with higher habitual physical activity levels may better adjust energy intake in response to energy balance perturbations. The effect of these individual characteristics and behaviours on appetite-related hormone responses to exercise remains equivocal. These findings support the continued promotion of exercise as a strategy for inducing short-term energy deficits irrespective of adiposity and sex, as well as the ability of exercise to positively influence energy balance over the longer term. Future well-controlled studies are required to further ascertain potential mediators of appetite responses to exercise.

Wind turbine upgrades have been spreading in the recent years in the wind energy industry, with the aim of optimizing the efficiency of wind kinetic energy conversion. This kind of interventions has material and labor costs and it is therefore fundamental to estimate realistically the production improvement. Further, the retrofitting of wind turbines sited in harsh environments might exacerbate the stressing conditions to which wind turbines are subjected and consequently might affect the residue lifetime. This work deals with a case of retrofitting: the testing ground is a multi-megawatt wind turbine from a wind farm sited in a very complex terrain. The blades have been optimized by installing vortex generators and passive flow control devices. The complexity of this test case, dictated by the environment and by the features of the data set at disposal, inspires the formulation of a general method for estimating production upgrades, based on multivariate linear modeling of the power output of the upgraded wind turbine. The method is a distinctive part of the outcome of this work because it is generalizable to the study of whatever wind turbine upgrade and it is adaptable to the features of the data sets at disposal. In particular, applying this model to the test case of interest, it arises that the upgrade increases the annual energy production of the wind turbine of an amount of the order of the 2%. This quantity is of the same order of magnitude, albeit non-negligibly lower, than the estimate based on the assumption of ideal wind conditions. Therefore, it arises that complex wind conditions might affect the efficiency of wind turbine upgrades and it is therefore important to estimate their impact using data from wind turbines operating in the real environment of interest.

Human African Trypanosomiasis (HAT) commonly known as sleeping sickness, is a neglected tropical vector borne disease caused by trypanosome protozoa. It is transmitted by bites of infected tsetse fly. In this paper we first present the vector-host model which describes the general transmission dynamics of HAT. In the tsetse fly population, the HAT is modelled by three compartments while in the human population, the HAT is modelled by four compartments. The next generation matrix approach is used to derive the basic reproduction number, R₀, and also it is proved that if R₀ ≤ 1 the disease free equilibrium is globally asymptotically stable, which means the disease dies out. The disease persist in the population if the value of R₀ > 1. Furthermore, the optimal control model is determined by using the Pontryagin’s maximum principle with control measures such as education, treatment and insecticides used to optimize the objective function. The model simulations confirm that the use of the three control measures are very efficient and effective to eliminate HAT in Africa.

As more end devices are getting connected, the Internet will become more congested. A variety of congestion control techniques have been developed either on transport or network layers. Active Queue Management (AQM) is a paradigm that aims at mitigating the congestion on the network layer by active buffer control to avoid overflow. However, finding the right parameters for an AQM scheme is challenging, due to the complexity and dynamics of the networks. On the other hand, the Explicit Congestion Notification (ECN) mechanism is a solution that makes visible incipient congestion on the network layer to the transport layer. In this work, we propose to exploit the ECN information to improve AQM algorithms by applying Machine Learning techniques. Our intelligent method uses an artificial neural network to predict congestion and an AQM parameter tuner based on reinforcement learning. The evaluation results show that our solution can enhance the performance of deployed AQM, using the existing TCP congestion control mechanisms.

Parts produced by laser or electron-beam powder bed fusion (PBF) additive manufacturing are prone to residual stresses, deformations, and other defects linked to non-uniform temperature distribution during the manufacturing process. Several researchers have highlighted the important role scan sequence plays in achieving uniform temperature distribution in PBF. However, scan sequence continues to be determined offline based on trial-and-error or heuristics, which are neither optimal nor generalizable. To address these weaknesses, we have articulated a vision for an intelligent online scan sequence optimization approach to achieve uniform temperature distribution, hence reduced residual stresses and deformations, in PBF using physics-based and data-driven thermal models. This paper proposes SmartScan, our first attempt towards achieving our vision using a simplified physics-based thermal model. The conduction and convection dynamics of a single layer of the PBF process are modeled using the finite difference method and radial basis functions. Using the model, the next best feature (e.g., stripe or island) that minimizes a thermal uniformity metric is found using control theory. Simulations and experiments involving laser marking of a stainless steel plate are used to demonstrate the effectiveness of SmartScan in comparison to existing heuristic scan sequences for stripe and island scan patterns. In experiments, SmartScan yields up to 43% improvement in average thermal uniformity and 47% reduction in deformations (i.e., warpage) compared to existing heuristic approaches. It is also shown to be robust, and computationally efficient enough for online implementation.

A heat pump with thermal storage system is a system that operates a heat pump during night-time using inexpensive electricity; during this time, the generated thermal energy is stored in a thermal storage tank. The stored thermal energy is used by the heat pump during daytime. Based on a model of a dual latent heat storage tank and a heat pump, this study conducts control simulations using both conventional and advanced methods for heating in a building. Conventional methods include the thermal storage priority method and the heat pump priority method, while advanced approaches include the region control method and the dynamic programming method. The heating load required for an office building is identified using TRNSYS, used for simulations of various control methods. The thermal storage priority method shows a low coefficient of performance (COP), while the heat pump priority method leads to high electricity costs due to the low use of thermal storage. In contrast, electricity costs are lower for the region control method, which operates using the optimal part load ratio of the heat pump, and for dynamic programming, which operates the system by following the minimum cost path. According to simulation results for the winter season, the electricity costs using the dynamic programming method are 17% and 9% lower than those of the heat pump priority and thermal storage priority methods, respectively. The region control method shows results similar to the dynamic programming method with respect to electricity costs. In conclusion, advanced control methods are proven to have advantages over conventional methods in terms of power consumption and electricity costs.

Background: The abrupt implementation of COVID-19 lockdown had impacted the management of diabetes mellitus. Limited access to health facilities and alterations in daily lifestyle put metabolic control among patients at risk. Thus, we observed the differences in metabolic control parameters in diabetic patients before and during the lockdown. Methods: We performed searches from five databases. Meta-analyses were done using random or fixed-effect approaches with glycemic control parameters (HbA1c, RBG, FBG, TIR, TAR, TBR) as primary outcomes. Mean difference (MD), Confidence Interval (CI), and p-value were calculated. Lipid profile presented as secondary outcome. Results: 21 studies with 3992 diabetic patients were included in the study. Meta-analysis presented an increase on HbA1c of T1D and T2D patients [MD=+0.06% (95%CI -0.10–0.23), I²=77%, p=0.45], TBR of T1D patients [MD=-0.05% (95%CI -0.38–0.28), I²=0%, p=0.77], FBG of T2D patients [MD=+3,47 mg/dL (95%CI 1.22–5.73), I²=0%, p=0.002], and lipid profile on qualitative analysis. However, TIR, TAR, and RBG of T1D patients were improved [MD=+3.52% (95%CI 0.29–6.74), I²=76%, p=0.03; MD=-3.36% (95%CI -6.48–-0.25), I²=75%, p=0.03; MD=-0.91 mg/dL (95%CI -4.52–6.34), I²=88%, p=0.74]. Conclusion: Lockdown enforcement did not worsen the glycemic control parameter in diabetic patients. Particular parameters inclined to improve during the lockdown.

This research not only dedicated a less restrictive method of iteration-varying function for a learning control law to design a controller but also synchronize two nonlinear systems with free time-delay. In addition, the mathematical theory of system synchronization has proved rigorously and the theory verified through an example to demonstrate the behavior of each parameter in the theory. The design of a controller using the iterative learning control law is significant for robotic tracking. The controller in this research generates a feed-forward control input using the error dynamics among the drive-response systems. The error dynamics satisfies the Lyapunov function and the combination of output errors, which respectively represented relative estimated differences of the drive-response systems. The iterative learning control rule serves the function of a filter adding previous control error after the end of each iteration. The numerical example of a synchronous system is given a Lorenz system for driving and another with the iterative learning control law for response under different initial condition. The results verify and demonstrate the proposed mathematical theory. The simulation exhibits consistency in the behavior of each parameter to match mathematical theory.

In this manuscript, we present a high-fidelity physics-based truth model of a Single Machine Infinite Bus (SMIB) system. We also present reduced-order control-oriented nonlinear and linear models of a synchronous generator-turbine system connected to a power grid. The reduced-order control-oriented models are next used to design various control strategies such as: proportional-integral-derivative (PID), linear-quadratic regulator (LQR), pole placement-based state feedback, observer-based output feedback, loop transfer recovery (LTR)-based linear-quadratic-Gaussian (LQG), and nonlinear feedback-linearizing control for the SMIB system. The controllers developed are then validated on the high-fidelity physics-based truth model of the SMIB system. Finally, a comparison is made of the performance of the controllers at different operating points of the SMIB system.

Disrupted nutrient recycling is a significant problem for Europe, while phosphorus and nitrogen are wasted instead of being used for plant nutrition. Mineral phosphate is critical raw material, which contains environmentally hazardous elements such as cadmium and uranium. Therefore, phosphorus recovery from agricultural by-product streams is critically important key priority. Phosphorus recovery from food grade animal bone by-products have been applied researched since 2002 with objective driven evolution progress towards specialized pyrolysis processing technology and animal bone char product (ABC) developments in economical industrial scale. Different animal bone by-products tested under different conditions at 400 kg/h throughput capacity in the continuously operated 3R zero emission autothermal carbonization system. The different material core treatment temperatures (between >300°C and <850°C) were combined with different residence times under industrial productive processing conditions. It has been industrial demonstrated that material core treatment temperature <850°C with 20 minutes residence time is necessary to achieve high quality ABC with useful agronomic value. The output ABC product having concentrated >30% phosphorus pentoxide (P2O5) and specific quality innovative fertilizer for agronomical efficient organic and low input farming applications as functional organic fertilizer, soil improver, growing medium and/or fertilizing product blend with high mineral phosphate fertiliser replacement value.

Teacher burnout has been revealed to be one of the most common negative consequence of the COVID-19 pandemic The purpose of this study was to identify distinct psychological resources and burnout risk profiles of teachers and to examine their association with Kolb’s Educator Roles and the professional experience. Methods: The survey data were collected from 330 preschool and primary school (84 males, Mage = 38.3, SD = 9.14) teachers using a convenience sampling method. Results: The two-step cluster analysis revealed two distinct profiles. The first profile, ‘High psychological resources, no burnout risk’, was characterised by absent symptoms of burnout and increased levels of well-being, self-control, and positive emotionality. The second profile, ‘Moderate psychological resources, mild burnout’, was associated with medium levels of well-being, self-control and positive emotionality accompanied by mild burnout. Our findings highlighted that cluster 1 had a significantly higher score for the Facilitator role and cluster 2 for the Expert and Coach roles. In addition, teachers with less professional experience were more likely to belong to cluster 1, taking into account their good skills on digital literacy. Conclusions: These findings help to provide new insights into the explanation of teacher burnout and the design of intervention programmes.

In the development of automatic control, PID control is the oldest of the basic control mode, the control algorithm is the most widely used in engineering, especially the applied research of robustness has extensive engineering practical value. In this paper, based on the principle of the internal model PID parameter setting method was studied, through different approximate processing method, derived the three different formula of PID internal model setting and simulation verify the effectiveness of the algorithm. At the same time, the robustness of the controlled process under different parameter perturbation is theoretically analyzed and simulated.Finally, the paper summarizes the whole paper and looks forward to the future development trend.

Though innovations for sustainable management of natural resources have emerged over time, the rising demand for nature based health solutions and integration of endemic flora into global value chains could have adverse impacts on ecosystems. The ecological risks in the exploitation of wild medicinal plant resources are exacerbated by a myriad of agrotechnological risks and challenges that highly constrain their domestication. Successful exploitation and commercialization of medicinal plants thus require a clear understanding of their demand and production systems or value chain analysis. Accordingly there is need for innovative approaches towards their integration into global value chains. Since quality and safety, traceability, certification, as well as, consumer tastes and preferences are critical drivers in purchasing decisions by global consumers, they are inadvertently exploited to weaken Indigenous knowledge (IK), undermine common property rights and entrench value chains that favour a few elite buyers. This tend to create pervasive incentives for overexploitation of medicinal plant resources and environmental degradation. Potential solution lies in the recognition of drivers of vulnerability to environmental degradation and the innovative use of policy bricolage, feedback loops and interactions between knowledge, power and agency on one hand, and collective action and property rights institutions on the other hand. We conceptualise a framework that can mediate a transformational agenda and enhance systematic understanding of sustainability lenses in endemic medicinal plant resources value chains. This could in turn strengthen IK, enhance collective action and promote participation of local actors with positive impact on the utilisation and integration of endemic medicinal plant resources into global value chains.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is a novel coronavirus that causes the new Coronavirus disease (COVID-19). The symptoms range from mild to severe with a higher incidence of severe cases seen in patients with risk factors such as older age and comorbidities. COVID-19 is mainly spread through the inhalation of respiratory droplets from coughing or sneezing or via contact with droplet-contaminated surfaces. Paramedics should be aware that some aerosol generating procedures (AGPs) may put them at a higher risk of contracting the virus via possible airborne transmission. The use of remote triage clinical assessment is likely to increase as a result of the pandemic. There is no curative drug treatment for the virus and some medications may exacerbate its effects or make patients more susceptible to it. Paramedics should accept that feeling stressed by the pandemic is a natural response. Official guidelines and advice are evolving continually as the evidence on SARS-CoV-2 and COVID-19 grows. Paramedics should keep up to date with the latest clinical guidance from their employers.

Spodoptera frugiperda is a widely distributed insect pest that causes major economic losses in various crops, particularly maize. On the other hand, Beauveria bassiana is an entomopathogenic fungus that establishes symbiotic associations with many plants and contributes to tolerance against biotic and abiotic stresses. In the present work, under field conditions, 1x106 (first trial) and 1x10⁸ (second trial) of B. bassiana (GHA strain) blastospores were used for corn’s seed inoculation. In the first field trial, a higher number of larvae were present in the negative control plants in comparison with those in B. bassiana-treated plants. No larvae were found in negative control and B. bassiana-treated plants in the second field trial. In further laboratory experiments, the effects of the B. bassiana strains GHA, in addition to a native strain (PTG4) also delivered via seed treatment in maize seedlings, on S. frugiperda growth, development, and mortality were evaluated. 1x10⁶ B. bassiana blastospores were used to inoculate maize seeds, which were germinated and grown to seedlings under growth chamber conditions. Third-instar S. frugiperda larvae were allowed to feed on B. bassiana-treated and -untreated (negative control) seedlings until reaching 6th instar and transferred to artificial diet until reaching adult stage. Results showed that larvae feeding on B. bassiana strain PTG4 prolonged their larval stage. Furthermore, feeding with plants treated with B. bassiana strains yielded fewer S. frugiperda male moths and the female moths emerged with altered wings, compared with the untreated control. In conclusion, seed treatment with B. bassiana in maize reduced S. frugiperda infestation of maize plants in field trials. Besides S. frugiperda development was affected in laboratory trials.

This study purposes the use of plug-in electric vehicles for demand side management (DSM) considering uncertainties in demand as well as uncertainties due to mobility of PEV to mitigate peak demand. The solution also seeks to reduce electric cost in addition to reducing the effects of greenhouse gases. In recent years DSM using distributed storage system such as battery energy management system (BESS) and plugged-in electric vehicles (PEV) have become very prevalent with most implementations resorting to deterministic load forecast. These methods do not consider the potential growth in demand making their solutions less robust. In this study we propose a real-time density demand forecast and stochastic optimization for robust operation of PEV for a building. This method accounts for demand uncertainties in addition to uncertainties in mobile energy storage as found in PEV, making the resulting solution robust as compared to the deterministic case. A case study on a real site in South Korea is used for verification and testing. The proposed study is verified and tested against existing algorithms. The result verifies the effectiveness of the proposed approach

Lumpy skin disease (LSD) is an emerging transboundary viral disease of cattle originating from the African continent. Here we describe the first LSD outbreak reported in the Republic of Kazakhstan, in July 2016. Initially, LSD was reported in a cattle farm located 49 km from Kazakh –Russian border in, Atyrau Oblast in West Kazakhstan. Subsequently, the disease spread to neighbouring farms situated within the same district. Following a preliminary investigation, the local State Veterinary Service declared a strict quarantine according to the State Contingency Plan, along with immediate total stamping out and cattle movement restrictions. During the outbreak, the number of affected cattle within an epidemiological unit reached 459 cattle out of registered 3557 susceptible cattle with 12.90% morbidity and 0.96%, mortality. This manuscript presents the epidemiological situation, the diagnosis, the control measures including mass vaccination and the stamping out campaign.s