Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

New composite with core-shell structure based on magnesium hydride and finely dispersed aluminum powder with aluminum oxide shell was mechanically synthesized. We used magnesium chips to produce magnesium hydride and aluminum wire after exploitation to produce nano-sized aluminum powder. The beginning of the hydrogen release from composite occurred at the temperature of 117°C. The maximum desorption temperature from the MgH₂-EEWAl composite (10 wt.%) is 336°C compared to pure magnesium hydride – 417°C. The mass content of hydrogen in the composite is 5.5 wt.%. The positive effect of aluminum powder produced by the electric explosion of wires method on reducing the activation energy of desorption was demonstrated. Calculations showed that the activation energy of desorption for the composite is 106±1 kJ/mol, compared with pure magnesium hydride, whose activation energy was 155±2 kJ/mol. The results obtained make it possible to expand the possibility of using magnesium and aluminum waste for hydrogen energy.

The Indorama Eleme Petrochemical Limited (IEPL) is found in the southern part of Nigeria more specifically on the Rivers State southern religion Nigeria. It consists of five distinct units, each of which generates its own unique trash at a rate of around 3115.98 tonnes per year. This study had the goal of concentrating on the management of the processing wastes in order to minimize the negative effects that they have on the environment. It is necessary to have an understanding of the number, nature, and make-up of IEPL's industrial wastes in order to effectively manage and regulate the development of waste there. As a result, we decided to collect data through the use of questionnaires. The classification of industrial wastes was accomplished by doing a comparative study and synthesis of research that were relevant to the management of petrochemical waste. Because an individual coding system is required for the integrated management of industrial waste, we gave each type of trash a code that consists of thirteen digits. The primary components of trash were catalysts (9.58 percent), metallic materials (7.62 percent), plastic barrels (35.77 percent), coke (12.66 percent), wood (4.47%), oil (4.15%), glass (0.028 percent), cooling tower packaging (6.7 percent), and other material (18.83 percent). According to the findings of the investigation into the physical qualities of the wastes, only 11.81% of these residues were liquid, while 88.19% were solid. The current handling of these wastes has been experiencing significant difficulties as of late. garbage management at IEPL was particularly challenging due to the wide variety of wastes produced there and the dangerous nature of the wastes themselves (88.19% of garbage was hazardous waste). Recycling and reuse of garbage may have been the greatest decision in some situations; yet, incineration and disposal of waste are also necessary options.

In this study, the effects of food waste (FW) compost, vermicompost, and chemical fertilizers on the growth of organic red radish and soil quality are investigated to promote sustainable agriculture. Utilizing a comparative approach, it assesses the impacts of these fertilizers on various plant growth metrics and soil characteristics, highlighting the potential of converting FW into nutrient-rich amendments as a sustainable alternative to chemical fertilizers. The results indicate a significant variation in fresh weight among different treatments. For example, the FV 25% treatment demonstrated a relatively high mean fresh weight of 7.9664, while the CO 50% treatment yielded a much lower mean fresh weight of 0.2589. These numbers underscore the potential efficacy of specific FW treatments in enhancing plant growth, with VC 50% and FV 25% showing considerable promise in increasing crop yield. The study concludes that FW compost and vermicompost significantly enhance plant growth and soil quality, advocating for their use as sustainable and environmentally friendly alternatives to chemical fertilizers. The findings emphasize the importance of selecting appropriate fertilizer types and concentrations to optimize agricultural productivity and environmental sustainability, supporting the incorporation of FW into agricultural systems as a beneficial resource.

Control over the composition of III-V ternary nanowires grown by the vapor-liquid-solid (VLS) method is essential for bandgap engineering in such nanomaterials and fabrication of functional nanowire heterostructures for a variety of applications. From the fundamental viewpoint, III-V ternary nanowires based on group V intermix (InSbxAs1-x, InPxAs1-x, GaPxAs1-x and many others) present the most difficult case, because the concentrations of highly volatile group V atoms in a catalyst droplet are beyond the detection limit of any characterization technique and therefore principally unknown. Here, we present a model for the vapor-solid distribution of such nanowires, which fully circumvents the uncertainties that remained in the theory so far, and link the nanowire composition to the well-controlled parameters of vapor. The unknown concentrations of group V atoms in the droplet do not enter the distribution, despite of the fact that a growing solid is surrounded by the liquid phase. The model fits quite well the available data on the vapor-solid distributions of VLS InSbxAs1-x, InPxAs1-x and GaPxAs1-x nanowires grown with different catalyst. Even more importantly, it provides a basis for the compositional control of III-V ternary nanowires based on group V intermix, and can be extended over other material systems where two highly volatile elements enter a ternary solid alloy through a liquid phase.

The increasing importance of batteries in the 21st century and the challenges posed by the anticipated growth in end-of-life batteries, particularly in Europe, are addressed. Projections indicate a significant increase in battery waste, with a specific focus on the recycling of black mass (BM)—a complex and hazardous byproduct of the battery recycling process. The research employs the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) methodology to systematically analyze the hazardousness of BM derived from various types of batteries. The findings reveal the inherently hazardous nature of BM, classifying it under multiple hazardous properties (HPs) according to European regulations. The urgent need for a definitive legislative classification of the hazardousness of BM is emphasized, and the potential of innovative technologies and strategies to improve recycling performance while mitigating risks is highlighted. The research significantly contributes to understanding the complexities of BM recycling, providing a foundation for future advancements in this area and emphasizing the need for further exploration and economic feasibility analysis of recycling technologies.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

The construction of reinforced concrete (RC) structures inevitably consumes an excessive number of rebars, leading to significant cutting waste and carbon emissions. Extensive research has been conducted to minimize this issue and its consequences; however, these methods consistently consume a substantial number of rebars. This includes a previous study that utilizes the lap splice position optimization and special-length rebar concept without considering the lapping zone regulation. Moreover, conventional lap splices pose inherent drawbacks that could jeopardize the structural integrity of RC members. In contrast, mechanical couplers eliminate the need for rebar lapping, effectively reducing rebar consumption. This research aims to evaluate the impact of an integrated mechanical coupler and special-length-priority minimization algorithm on the reduction in rebar consumption and cutting waste in RC columns, achieving near-zero cutting waste. To validate the effectiveness of the proposed algorithm, it was applied to the column rebars of an RC building. The results revealed a significant reduction in ordered rebar consumption by 18.25%, accompanied by substantial reductions in cutting waste (8.93%), carbon emissions (12.99%), and total costs (10.81%) compared with a previous study. The outcomes provide the industry with insights into further reducing rebar consumption and its related consequences. Applying the proposed algorithm to various construction projects will further amplify the corresponding benefits.

The poor solvent crystallization of carbapenem CS-023 has been performed at 25 °C. The following results have been obtained: 1) A solvate crystal Form A (5/2 Ethanol·1/2 H2O) is recovered from 80 v/v% ethanol solution, 2) Form A transforms to Form H (4H2O) by the solid-phase transition through the solvate-free polymorph, Form A-2, and Form A also transformed to Form C (1Ethanol·3H2O) by the solvent-mediated transformation. In the present study, we found that Form C also transforms to Form H by the solid-phase transition through the solvate-free polymorph, Form C-2. The three polymorphs, Form A, H, and C, were composed of the helical-chain structures, respectively. However, there was an incomprehensible affair in the solid phase transition among the three polymorphs. Namely, Form A comprised a left-handed helix.On the other hand, Form C and Form H’s helix chains were in a left- and right-handed helix complex. The solid-phase transition of Form A into Form H suggested the switch of helicity in the solid. We attempted to explain the helicity change in the solid phase transition. As a result, it was suggested that the over-absorption of water of Form A-2 at high humidity plays a vital role in the helicity change.

Nano-drugs and nano-delivery systems are rapidly evolving, with new strategies emerging in the current practices. The evolution of these technologies began with modifying the chemical structure, progressing to supramolecular ionic complexes, and culminating in elegant ad hoc delivery systems. Nanoparticles have numerous benefits as a carrier system for delivering therapeutic agents to intra-arterial sites. These benefits include their subcellular size, targeted surfaces, good suspensibility, and uniform dispersity, making them an ideal choice for catheter-based delivery. Despite the advancements made in the field of nano-drugs and nano-delivery systems, there are still some hurdles to overcome in terms of their commercial availability.The current review presents an updated summary of recent advancements in nano-drugs and nano-delivery systems, including their commercial availability. We aim to discuss the present challenges and prospects of commercially available nano-drugs and nano-delivery systems. Here, we provide a precise and informative overview of the current state of these technologies and underscore the potential they hold for future developments. Further, we have categorized commercially available modifications, name, parent company and their main applications in nano-drugs.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Peptide/Histidine Transporter PHT1 (SLC15A4) is expressed in lysosomal membranes of immune cells where it plays an important role in metabolic and inflammatory signaling. PHT1 is an H+-coupled/histidine symporter that can transport a broad range of oligopeptides, including a variety of bacterial-derived peptides. Moreover, it enables the scaffolding of various metabolic signaling molecules and interacts with key regulatory elements of the immune response. Therefore, it is not surprising that PHT1 is associated with the development of autoimmune diseases, such as systemic lupus erythematosus (SLE). Unfortunately, the pharmacological development of PHT1 has been hampered by the lack of appropriate transport assays. With the aim to address this shortcoming, a novel transport assay based on solid supported membrane-based electrophysiology (SSME) is presented. Key findings of the present SSME studies include the first recordings of electrophysiological properties, a pH dependence analysis, an assessment of PHT1 substrate selectivity, as well as the transport kinetics of the identified substrates. In contrast to previous works, PHT1 is studied its native lysosomal environment. Moreover, observed substrate selectivity is validated by molecular docking. Overall, this new SSME-based assay is expected to contribute to unlock the pharmacological potential of PHT1 and to deepen the understanding of its functional properties.

The influence of aluminosilicate pozzolanic waste, specifically spent fluid catalytic cracking catalyst (FCCW) and metakaolin waste (MK) from expanded glass industry, on the properties of hardened Portland cement paste were analysed. The study involved replacing part of cement with FCCW and MK and observing their impact on hydration, microstructure, density and compressive strength of hardened cement paste. Various analysis methods were employed, including X-ray diffraction (XRD), thermogravimetric analysis (TG), and scanning electron microscopy (SEM), to understand the changes in the structure of hardened cement paste during hydration. The findings revealed that FCCW tends to accelerate cement hydration process due to its high surface area and pozzolanic activity. Notably, the formation of portlandite crystals was observed on FCCW particle surfaces in a specific direction. These crystals appeared smaller and developed in different directions in compositions containing a composite binder with mixture of FCCW and MK in a ratio 1:1. This could be influenced by pozzolanic reactions activated by fine particles of MK and the formation of calcium silicate hydrates (CSH) and calcium alumino silicate hydrates (CASH) in the presence of portlandite. XRD and TG results indicated that the specimens containing a composite binder exhibited the least amount of portlandite. The compressive strength of these specimens increased compared to control specimens, although the amount of cement was 9% lower.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

Recent years have experienced an increase in construction and demolition waste (C&DW), which is the most significant solid waste stream. C&DW is contributing to exceeding all planetary boundaries and presents a range of other issues. In order to better understand the existing research on C&DW, a global bibliographic analysis was undertaken through seven groups of keyword searches and the results visualised using VOCviewer. The results show that C&DW receives only a modest research attention compared to other areas of waste, and this is despite an exponential increase in C&DW research since 2016. The analyses also show that concrete is the most researched material in terms of C&DW, and that reuse, recycling, and circular economy are so far attracting only proportionally modest research attention. This signals a need for further acceleration of the C&DW research, and specifically for more research on reuse, recycling, and circular economy for materials other than concrete.

Aquaculture by-products can be compromised an important liming material of increasing soil pH and soil fertility. The aim of this research was to assess the effect of mussel shells on soil pH, on organic matter and on soil nutrients. In this study a pot experiment was carried out at the De-partment of Ichthyology and Aquatic Environment (University of Thessaly, Greece). A acidic soil (pH 4.26) amended with 6 different proportions of mussel shell (0.0, 0.1, 0.3, 0.5, 1, 3 and 6%) in two different grain sizes (Fine powder (>1 mm) and Coarse powder (1-2 mm)), resulting in 13 treatments. According to the results, it was observed that pH, organic matter, Available P and Exchangeable K increased. Specifically, the highest pH values observed at 6% rate. Available P and Exchangeable K achieved the highest content at 6% Fine powder treatment, 46.2 and 190.1 mg kg-1, respectively. Similarly, organic matter had the highest value in 6% Fine powder pots (2.27%). Moreover, Total N concentration varied from 0.11 to 0.14 but no statistically significant different was noticed between the treatments. In conclusion, mussel shells can compose a promising liming material in the agriculture section.

Printed Circuit Boards (PCBs) are essential to most electronic devices. Digitalization and upgradation of gadget generates lots of PCB-containing electronic waste. Conserving resources and protecting the environment requires recycling such e-waste. The present paper is focused on the recovery of metals from PCBs by physical pretreatment and hydrometallurgical processes. Initially, the waste PCBs were pre-treated to separate metallic and non-metallic fractions. The metallic concentrate was leached using nitric acid (strong oxidative agent) for dissolution of metals. The system was fully jacketed with scrubber and condenser so that no emission of toxic gases to the environment. The process parameters viz. effect of acid concentration, pulp density, temperature, time, etc. were optimized and the obtained data were scientifically validated. Kinetics leaching fitted well with the Shrinking core model, XB = kc.t for Cu, (1-(1-XB)1/2) for Ni and 1-3(1-XB)2/3 + 2(1-XB) for Pb. The optimized conditions derived from these studies will be useful for recovery of metals from waste PCBs, and tin left in the residue could be further treated for the purpose of safe disposal or the utilization in an environmentally friendly manner. The developed process provides environmental benefits and has potential to be commercialized after scale-up studies.

Information and telecommunications technology (ITT) have expanded into many aspects of modern life and have positively affected human life even in the most remote areas of developing countries. The rapid growth in ITT has led to an improvement in the capacity of computers but simultaneously to a decrease in the product’s lifetime as a result of which increasingly large quantities of e-waste are generated annually. It contains hazardous components that if it is not properly managed, can have adverse environmental and health effects. The management of e-waste poses significant challenges in developing countries. Due to the lack of adequate infrastructure, e-waste is burned or dumped in open areas. Informal and inefficient recycling practices are generally employed which further exacerbate pollution and health risks. So, the implementation of e-waste management, adequate recycling, and waste disposal facilities have become crucial concerns. This article reviews the concept of e-waste generation, challenges, disposal, and its impact on human health & environment in detail.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

Sodium-phosphate-based glass-ceramics (GCs) are promising materials for a wide range of applications, including solid-state sodium-ion batteries, microelectronic packaging substrates, and humidity sensors. This study investigates the impact of 24-hour heat-treatments at varying temperatures on Na-Ge-P glass, with a focus on (micro)structural, electrical, and dielectric properties of prepared GCs. Various techniques such as powder X-ray diffraction (PXRD), infrared spectroscopy-attenuated total reflection (IR-ATR), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) are employed. With the elevation of heat-treatment temperature, crystallinity progressively rises; at 450 °C, the microstructure retains amorphous traits featuring nanometric grains, whereas at 550 °C, heat-treatment results in fully crystallized structures characterized by square-shaped micron-scale grains of NaPO3. The insight into the evaluation of electrical and dielectric properties is provided by Solid-State Impedance Spectroscopy (SS-IS), revealing a strong correlation with the conditions of controlled crystallization and observed (micro)structure. The glass-ceramic heat-treated at 450 °C achieves the highest DC conductivity of 2.30×10–8 Ω–1 cm–1 at 393 K. As the heat-treatment temperature rises, the crystallization of the NaPO3 phase depletes the glass matrix of mobile Na+ ions, resulting in a reduction in DC conductivity. Dielectric parameters also decrease with rising heat-treatment temperature, with the glass-ceramic heat-treated at 550 °C displaying the lowest permittivity of 19.37 and the dielectric loss of 0.008. This research uncovers the intricate relationship between heat-treatment conditions and material properties, emphasizing that controlled crystallization allows for precise modifications to microstructure and phase composition within remaining glassy phase, ultimately facilitating fine-tuning of material properties.

The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

This study focuses on the synthesis, characterization and study of a new perovskite-type materials as cathode in SOFC. The synthesized doped perovskites have been successfully synthesized with high purity. The electrochemical performance of these materials was extensively examined through the characterization of I-V-P and EIS curves at the three temperatures: 750, 800 and 850 °C. Where it is revealing a substantial reduction of total resistances by approximately 50% and 70%, accom-panied by an impressive increase in power densities by around 200% and 300%, respectively. The cell featuring Sm0.01Sr0.99Fe0.5Co0.5O3 exhibited the most commendable electrochemical properties at each temperature, following closely were Pr0.01Sr0.99Fe0.5Co0.5O3 and La0.01Sr0.99Fe0.5Co0.5O3.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

SDG target 12.3 calls for halving food waste at retail, food service, and household by 2030. The food waste index for this purpose includes parts attached to food that are usually removed intentionally ("unavoidable food waste") and allows counting the conversion to animal feed and utilisation as biomaterial as means of reduction. In Japan, the "Food Waste Recycling Law" which has been in effect since 2001, promotes the recycling of food waste generated from businesses, designating feed conversion as top priority. On the other hand, based on the more recent "Food Loss Reduction Promotion Act" of 2019, the government is currently promoting the reduction of avoidable food waste, as to meet the SDG target. Based on statistical sources and interviews with Ministry officers, this paper explains the history and achievements of Japan's 23-year policy based on the Food Recycling Law, as well as the tension between the two legislations.

Plant waste biomass is the most abundant renewable energy resource on Earth. The main problem of utilising this biomass in anaerobic digestion is the long and costly stage of degrading its complex structure into simple compounds. A promising solution to this problem are fungi of the Trichoderma genus, which show a high capacity to produce hydrolytic enzymes capable of degrading lignocellulosic biomass. This article discusses the structure of plant waste biomass and the problems resulting from its structure in the digestion process. It presents the methods of pre-treatment of lignocellulose with a particular focus on biological solutions. Based on the latest research findings, key parameters related to the application of Trichoderma sp. as a pre-treatment method are discussed. In addition, the possibility of using the digestate from agricultural biogas plants as a carrier for the multiplication of the Trichoderma sp. fungi, which are widely used in many industries, was discussed.

Background: The liver has emerged as a frequent transplanted organ which can transmit T. gondii between seropositive donors and seronegative recipients. Associated with the immunosuppressive therapy of recipients, the presence of cysts in donor livers elevate the risk of severe toxoplasmosis in recipients. Objectives: The objective of the study was to verify the frequencies of positive serology in liver graft donors and their respective recipients, as well as to verify whether their clinical signs presented post-transplant are associated with the serological status of recipients. Patients and methods: All data on liver transplant recipients from 2008 to 2018 were obtained from the MVPeP electronic medical records of the Liver Transplant Service of FUNFARME/FAMERP. IgM and IgG anti-T. gondii antibody serology was investigated by chemiluminescence. According to the serological profile, four groups of recipients were assessed (G1: IgG-/IgM-; G2: IgG+/IgM-; G3: IgG+/IgM+, G4: IgG-/IgM+). Results: The numbers of recipients according to the serological profile groups were: G1: 20 (41.7%), G2: 26 (54.1%; G3: 2 (4.2%). No cases were found for G4. Post-transplant clinical manifestations such as fever without defined cause, lung nodules, headache, hepatosplenomegaly, encephalopathy and hepatitis (A, B and C) were reported in all groups. Conclusions: This study demonstrates that there is a high prevalence of T. gondii infection in liver recipients and, therefore, screening should be intensified. Furthermore, a high incidence of co-infection with hepatitis A was identified especially in patients who died in the post-transplant period.

Quarry waste fines and eggshells are unavoidable wastes which relentlessly contribute to environmental load and pollution. Although a number of studies have suggested various methods for recycling, these wastes remain underutilized due to some technical constraints. In addition, no study has yet been explored on the possibility of combining quarry waste fines (QWF) and eggshell powder (ESP) for tobermorite synthesis. Tobermorite is the main component which primarily provides strength to the autoclaved aerated concrete products. For this purpose, this study seeks to evaluate the potential of QWF- ESP mix at 10%, 15% and 20% amounts of cement, respectively. The XRF, XRD, and TGA–DTA techniques were used to characterize the waste materials while physical and mechanical property tests and XRD analysis were performed on the autoclaved samples. It was found that QWF contains 53.77% SiO2, while ESP contains 97.8% CaO which are key components for tobermorite synthesis. This study also revealed that the mixture with only 10% cement has the highest compressive strength among the QWF-ESP samples. Furthermore, the formation of tobermorite in the samples was confirmed through XRD analysis. Hence, the hydrothermal curing of QWF –ESP can be further developed to produce functional tobermorite – bearing materials.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

Natural fibers have attracted increasing interest as an alternative to produce environmentally friendly and sustainable materials. Particularly, hemp fibers have revealed to be widely used in various industrial applications due to their extremely unique properties. However, hemp can generate a large amount of agro-waste, and results in an attractive source of biopolymers for the development of low-cost materials in alternative to the raw materials and conventional petroleum-based plastics. In addition, deep eutectic solvents (DESs), a new type of truly green solvents, have been tested to remove gums, lignin, and other non-cellulosic components from hemp fibers. Reusing these components dissolved into the DESs to fabricate new materials directly by electrospinning is a very attractive but still unexplored endeavor. Thus, this innovative research to venture new upcycling pathways is focused on the fabrication of composite nanofibers by electrospinning of a gel-based blend of Poly(vinyl alcohol) (PVA) and hemp agro-waste (HW) dissolved into choline chloride (ChCl) : Glycerol (1:2) and ChCl : Urea (1:2) DES mixtures. The results obtained revealed that the produced nanofibers displayed uniform appearance with diameters ranging from 257.72 ± 65.63 nm to 380.78 ± 133.98 nm. In addition, the mechanical properties of the electro-spun composite nanofibers produced from the gel-based blends of HW dissolved in DESs and PVA (HW-DESs_PVA) were found to be superior, resulting in an enhanced tensile strength and Young’s modulus. Furthermore, the incorporation of HW into the nanofibers was able to provide bioactive antioxidant and antibacterial properties. Overall, this study demonstrated a promising, more sustainable, and eco-friendly way to produce electrospun composite nanofibers using HW in a circular economy perspective.

Sr4Al6O12SO4 samples were obtained from the compound mixture formed by a solid–state reaction of Al2O3, SrSO4, and SrCO3. Samples were compacted at 100MPa to form pellets of 1 and 4cm in diameter and were sintered at 1400°C for 4 hours. The compound was analyzed by X–ray diffraction. Static immersion and wettability tests were performed to evaluate corrosion resistance in contact with Al–Si. Corrosion tests were carried out by immersion at 800, 900, and 1000°C for 24, 50, and 100 hours, while wettability was carried out at 900, 1000, and 1100°C for 2 hours. Subsequently, the samples were prepared metallographically. Samples were analyzed by optical microscopy, scanning electron microscopy, and image analysis. In general, reaction products consisting of alumina, spinel, oxides, and sulfates were found. The contact angles obtained were 124° to 135°. It is concluded that ceramic substrate Sr4Al6O12SO4 is resistant to corrosion by Al–Si alloy, since the slight thickness of the reaction products found in the samples (100μm) considering the severe conditions of the experiment: 1000°C and 100 hours of isothermal temperature. Furthermore, it can be said that Sr4Al6O12SO4 is not wettable by Al–Si alloys.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

To ensure sustainable production and consumption in the agricultural sector, it is necessary to assess the contribution of each element of the nexus in the agricultural production chain. The aim of this study is to make a quantitative and qualitative analysis of the contributions of each element of the energy, water, waste and land nexus to agricultural products. A composite method approach combining aspects based on input-output model, Location Quotient (LQ) as well as competitive position is adopted. A database of nexus elements over a period from 2009 to 2018 is used for Cameroon, with ten regions considered. The results show proportions of around 0.42% energy, 67.88% water withdrawal, 11.91% harvested area, 97.81% waste for agricultural products. The geolocation of harvested areas shows that the largest portion is in the far north (1,373,829 ha) and the smallest in Adamawa (224,038 ha). Maximum production is in the central region (4,334,095 tons) and minimum in the Adamawa region (915,841 tons). The central, littoral and west regions are more representative of agricultural products. The analysis of the competitive position of agricultural products contributes to a better orientation of national strategies for agricultural sustainability according to existing potentials.

E-waste is considered the fastest-growing global waste stream and has become an emerging environmental challenge. The widespread usage of digital devices has generated a large amount of e-waste. According to the Ministry of Commerce, India annually generates ~14.5 lakh metric tons of e-waste and recycles only ~5 % of e-waste. Annually, the global production of e-waste has been expected to increase by 4–5 %. Advancements in IT and communication divisions have improved the usage of electronic equipment. Heavy metals such as (Pb), mercury (Hg), arsenic (As), tin (Sn), and organic chemicals such as polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), polybrominated biphenyls (PBBs), polybrominated dibenzo-p-dioxins (PBDDs), polybrominated diphenyl ethers (PBDEs) are subsequently released from e-wastes and contaminates soil and water sources. These toxic compounds are hazardous to human health and the environment. They are capable of entering various biological systems and causing alterations in respiratory functions of the lungs, DNA damage, impaired functioning of the thyroid, and increased risk of chronic diseases such as cancer and cardiovascular ailments. Such concerns raise the quintessential need to manage e-waste to prevent future hazards. This manuscript critically reviews the sources, health and environmental impact, disposal techniques, recycling, and regulation of e-waste.

Slags and ashes generated in thermal waste treatment facilities require proper management. In line with the principles of the circular economy, new, more economical and ecological possibilities for utilizing these substances are sought. These waste materials exhibit characteristics similar to rocks in many aspects. This study focuses on analyzing the similarities and differences between nine selected rocks and three samples of slags and ashes obtained from municipal waste incineration. The main research device used was a polarizing microscope, using reflected, transmitted and fluorescent light. Additionally, low-pressure gas adsorption equipment, as well as helium and quasi-liquid pycnometers, were used for complementary analysis. The parameters analyzed mainly covered broadly defined petrographic properties of rocks and slags, with a particular emphasis on porosity, porous structure and the spatial distribution of pores and fractures. The conducted analyses confirmed a significant similarity between slags and ashes and clastic sedimentary rocks such as sandstones and mudstones. The research results underscore the importance of petrographic microscopic studies for analyzing materials other than rocks. They also allow for exploring applications for slags and ashes in areas traditionally reserved for natural rock resources. The findings also indicate the necessity of using methods other than microscopic ones to describe the pore space of rocks. The lower measurement range of the optical microscope is limited to approximately 1 μm, covering only macropores. Other methods extend this characteristic to micro- and mesopores. Therefore, a combination of different methods is often employed to obtain a more comprehensive characterization of rock porosity.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

Flexible energy storage devices, such as solid-state supercapacitors, are becoming increasingly attractive due to their characteristics of high electrochemical performance, reliability, light weight, flexibility, absence of electrolyte leakage, high power density, and long lifetime. For the optimization of the solid-state symmetrical supercapacitor proposed in this work, it was employed in sodium and lithium form Aquivion electrolyte membrane, which serves as the separator and electrolyte. As electrode materials, carbon xerogels, synthesized by microwave-assisted sol-gel methodology, with designed and controlled properties were obtained. Commercial activated carbon (YP-50F, 'Kuraray Europe' GmbH) was used for comparison. Specifically, the developed solid-state symmetrical supercapacitors deliver sufficient high specific capacitances of 105−110 F g−1 at 0.2 A g−1, along with an energy density of 4.5 Wh kg−1 at 300 W kg−1, and in a voltage window of 0-1.2 V in an aqueous environments, also demonstrating excellent cycling stability up to 10,000 charge/discharge cycles. These results can demonstrate the potential applications of carbon xerogel as an active electrode material and cation exchange membrane as the electrolyte in the development of solid-state supercapacitor devices

Municipal Solid Waste Management (MSWM) struggles with significant policy and operational challenges, particularly concerning recyclables collection routes and fleet composition. Within the European Union, phasing out traditional fuel-based vocational vehicles, like garbage trucks, in favor of zero-emission alternatives is mandatory to achieve sustainable development objectives. Integrating electric solid waste collection vehicles into municipal fleets presents challenges due to differences in range, capacity, and noise levels. The emission is even more crucial in the systems where recyclables are collected separately, which requires a greater number of trips to be performed. This study addresses MSWM’s strategic aspect by minimizing the total cost of replacing waste collection vehicles while meeting emission constraints. The Fleet Transition Problem (FTP) was formulated and solved using a MARKAL-based approach. The objective of the FTP and a mixed integer linear program used to solve it is minimizing the overall cost of fleet modernization throughout a multi-phase planning horizon so that the sustainable transition of the fleet can be assured. Computational experiments affirmed the model’s effectiveness in strategizing fleet transition. This research outlines a multi-period model for transitioning to a zero-emission fleet and demonstrates the FTP’s potential for strategic decision-making. Notably, the study observes a consistent reduction in permissible emissions across the planning horizon.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

Lithium-ion batteries with improved energy densities have made understanding the Solid Electrolyte Interphase (SEI) generation mechanisms that cause mechanical, thermal, and chemical failures more complicated. SEI processes reduce battery capacity and power. Thus, a review of this area's understanding is important. It is essential to know how batteries degrade in EVs to estimate battery lifespan as it goes, predict, and minimize losses, and determine the ideal time for a replacement. Lithium-ion batteries used in EVs mainly suffer two types of degradation: calendar degradation and cycling degradation. Despite the existence of several existing works in the literature, several aspects of battery degradation remain unclear or have not been analyzed in detail. This work presents a systematic review of existing works in the literature. The results of the present investigation provide insight into the complex relationships among various factors affecting battery degradation mechanisms. Specifically, this systematic review examined the effects of time, side reactions, temperature fluctuations, high charge/discharge rates, depth of discharge, mechanical stress, thermal stress, and the voltage relationship on battery performance and longevity. The results revealed that these factors interact in complex ways to influence the degradation mechanisms of batteries. For example, high charge currents and deep discharges were found to accelerate degradation, while low temperatures and moderate discharge depths were shown to be beneficial for battery longevity. Additionally, the results showed that the relationship between cell voltage and State-of-Charge (SOC) plays a critical role in determining the rate of degradation. Overall, these findings have important implications for the design and operation of battery systems, as they highlight the need to carefully manage a range of factors to maximize battery performance and longevity. The result is an analysis of the main articles published in this field in recent years. This work aims to present new knowledge about fault detection, diagnosis, and management of lithium-ion batteries based on battery degradation concepts. The new knowledge is presented and discussed in a structured and comprehensive way.

Industries are required to utilize treatment technologies to reduce contaminants in wastewater prior discharge and valorize by-products to increase sustainability and competitiveness. Most acid leaching gypsum purification studies have obviated the treatment of the highly acidic wastewater produced. In this work, acidic wastewater from acid leaching purification of post-consumer gypsum was treated to recover a valuable solid product and reusable water. The main aims of this work were to determine the impact of recirculating acidic and treated wastewaters on the efficiency of the acid leaching purification process and to valorize the impurities in the wastewater. Samples were characterized through X-ray fluorescence and X-ray diffraction. SimaPro 9.5 and ReCiPe 2016 midpoint method were used for the life cycle assessment of three wastewater management approaches. The reuse of the acidic wastewater did not improve the chemical purity of gypsum. Soluble impurities were precipitated at pH 10.5 as a magnesium-rich gypsum that could be commercialized as fertilizer or soil ameliorant. The alkaline treated water was reused for 6 acid leaching purification cycles without impacting the efficiency of the purification process. An acid leaching-neutralization-filtration-precipitation approach demonstrated superior overall environmental performance. Barriers and enabling measures for the implementation of an in-house wastewater treatment were identified.

The global predicament of solid waste generation looms as a mounting crisis, profoundly impacting the world, particularly in developing nations. Each day, the world's population contributes millions of tonnes of municipal solid waste, with projections pointing toward further escalation in the coming years. This surge in waste, predominantly composed of cellulose-rich materials, correlates directly with heightened pollution, a threat that transcends borders and imperils humanity as a whole.To confront this ever-growing issue, cellulase, a potent hydrolytic enzyme capable of digesting cellulose, a chief component of solid waste, is explored as a potential solution. In this study, we harness cellulase enzymes derived from the digestive tracts of both Archachatina marginata and Oryctes rhinoceros larvae, employing them as biodegradation agents for cellulose-based waste materials.The cellulase enzymes are methodically isolated and partially purified via ammonium sulfate precipitation at 65% saturation. Their efficacy in breaking down a variety of waste categories, encompassing kitchen waste, leaves, paper, wood, and industrial waste, is meticulously assessed and benchmarked against carboxymethyl cellulose (CMC), a well-established laboratory substrate. The study also ascertains the specific activity of these enzymes.Spectrophotometric analyses of the cellulase enzymes' actions on the diverse waste materials unveil intriguing results. Archachatina marginata and Oryctes rhinoceros larvae exhibit distinct performance metrics, registering percentage ranges of (11.04% - 28.31%) and (33.69% - 189.11%) on wood waste, (76.52% - 196%) and (108.56% - 567.01%) on paper waste, (78.57% - 148.14%) and (163.33% - 436.76%) on leaf waste, (57.16% - 179.95%) and (63.38% - 457.05%) on kitchen waste, and (59.95% - 77.51%) and (117.26% - 155.23%) on industrial waste, respectively. This study underscores the substantial biodegradation potential inherent in cellulase enzymes from both Oryctes rhinoceros larvae and Archachatina marginata when applied to diverse waste materials. While the rates and impacts of waste degradation vary between these sources, their promising contributions to waste management come into focus, offering sustainable and innovative approaches to tackle the pressing global challenge of solid waste proliferation.

Speciation analysis is a relevant topic since the (eco)toxicity, bioavailability, bio (geo)chemical cycles, and mobility of a given element depend on its chemical forms (oxidation state, organic ligands, etc.). Reliability of analytical results for chemical species of elements depends mostly on the maintaining of their stability during sample pretreatment step and on the selectivity of further separation step. Solid phase extraction (SPE) is a matter of choice as most suitable and widely used procedure for both enrichment of chemical species of elements and their separation. Features of sorbent material are of great importance to ensure extraction efficiency from one side and selectivity from other side of SPE procedure. This review presents an update on the application of polymeric materials in solid-phase extraction used in non-chromatographic methods for speciation analysis.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

The paper presents a thorough examination of the burgeoning field of utilizing manufacturing waste for sustainable energy generation, aligning with the global imperative for resource efficiency and clean energy solutions. With the manufacturing sector being a significant contributor to waste generation, this study explores innovative approaches to transform waste materials into valuable resources, thereby mitigating environmental impacts and contributing to a circular economy. This work critically reviews current trends, emphasizing technological advancements, policy interventions, and market dynamics shaping the manufacturing waste utilization landscape. Noteworthy developments, such as advanced sorting technologies and the integration of digital solutions, are discussed in detail, showcasing their role in enhancing the efficiency of waste management processes. The study outlines future trends in the field, anticipating a shift towards closed-loop systems guided by circular economy principles. This comprehensive review aims to contribute to the discourse on sustainable waste management and energy generation by providing a holistic perspective on the field's current state and offering insights into the future trajectories that will propel manufacturing waste toward a more sustainable and circular future. The synthesis of technological innovation, collaborative efforts, and evolving regulatory frameworks presents a compelling case for the continued exploration of manufacturing waste as a valuable resource in the pursuit of a more sustainable and energy-efficient world.

Humification is a promising strategy to reduce the amount of animal waste generated in agriculture. This makes it possible to accumulate products with artificially obtained humic substances (HS) as analogues of natural HS, usually extracted from fossil sources (coal, peat). The review examines the main characteristics of various biological and physical-chemical methods (composting, anaerobic digestion, pyrolysis, hydrothermal carbonation, acid or alkaline hydrolysis, subcritical water ex-traction) used to form HS in animal waste humification products. A comparative analysis of the humification rates and yields of HS in these processes, the characteristics of artificial HS in products (humification index, polymerization index, degree of aromaticity, etc.) is carried out in connection with the use of certain methods of humification and types of animal waste. The main factors (ad-ditives, process conditions, waste pretreatment, etc.) that can increase the efficiency of humification and the properties of HS resources artificially obtained by various methods are highlighted. A generalizing analysis of the content of chemical elements in artificial HS obtained from various animal husbandry wastes in comparison with natural HS was carried out. Based on the results of the chemical composition analysis, the main trends and preferences regarding the most useful ap-plications of humification products as complex biomimetics are discussed.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

The accurate classification of landfill waste diversion plays a critical role in efficient waste management practices. Traditional approaches, such as visual inspection, weighing and volume measurement, and manual sorting, have been widely used but suffer from subjectivity, scalability, and labour requirements. In contrast, machine learning approaches, particularly Convolutional Neural Networks (CNN), have emerged as powerful deep learning models for waste detection and classification. This paper analyses VGG-16, InceptionResNetV2, DenseNet121, Inception V3, and MobileNetV2 models to classify real-life waste when trained on pristine and unadulterated materials, versus samples collected at a landfill site. When training on DiversionNet, the unadulterated material dataset with labels required for landfill modelling, classification accuracy was limited to 49.69% in the real environment. Using real-world samples in the newly formed RealWaste dataset showed that practical applications for deep learning in waste classification is possible, with Inception V3 reaching 89.19% classification accuracy on the full spectrum of labels required for accurate modelling.

A single-crystal of ytterbium-doped “mixed” yttrium-lutetium aluminium garnet with a stoichiometric composition of (Y0.601Lu0.233Yb0.166)3Al5O12 was grown by the Czochralski method and its structure, vibronic, spectroscopic and laser properties were studied. The stimulated-emission cross-section for Yb3+ ions was maximized to 2.53×10-20 cm2 at 1031 nm, the emission bandwidth is ~8 nm and the reabsorption-free luminescence lifetime of the 2F5/2 state is 1.063 ms. Pumped at 941 nm, the Yb-laser generated a maximum output power of 1.04 W at 1.03 and 1.05 μm with a high slope efficiency of 76.4% and a laser threshold of 76 mW. A continuous wavelength tuning over a range of 51.6 nm (1026.4 - 1078.0 nm) was also achieved. Power scaling is achieved using a 969 nm-diode pumped microchip cavity. A maximum output power of ~9 W is obtained at 1.05 μm with a slope efficiency of 76% and with an almost circular laser beam profile.

Rice cultivation is the main agricultural activity in Asia, and it results in an enormous amount of agricultural waste, that are usually disposed-off by burning, causing serious environmental health and climate problems. Pakistan is the tenth largest producer in the world and the fourth exporter of rice in the world. To date, there are no studies targeting Pakistan’s profile monitoring its contribution in open burning emissions from rice straw waste. This study presents the characterization of PCDD/Fs, PCBs and PAHs emissions from three samples of rice straw collected from the main rice cultivation regions of Pakistan (Punjab, Sindh and Azad Jammu and Kashmir) in relation to the role of metal-based agricultural additives. PCDD/Fs, PCBs and PAHs emissions were quantified using a fixed grid system biomass plant and measuring the macro-pollutants online and sampling the organic micro-pollutants and metals in isokinetic mode, followed by ISO and CEN standards methods. In addition, role of agrochemicals was monitored in terms of metal catalysis resulted in POPs emissions. This study provides the characterization of most relevant group of pollutants (metals, PCDD/Fs, PCBs and PAHs) as a result of agricultural waste combustion. The rice straw samples from AJK showed high values of organochlorine micro-pollutants compared to the values followed by samples from Punjab and Sindh, i.e., respectively, ∑PCDD/F (2594>1493>856 pg/Nm³) and ∑PCB (41>38>30 pg/Nm³). Whereas the organic micro-pollutants ∑PAH, indicators of incomplete combustion (PICs), were recorded high in the samples from Sindh followed by Punjab and AJK. This study supports the idea that the phenomena that lead to the formation of PCDD/F and PCB are influenced not only by poor combustion but also by the presence of metal catalysts or precursors in the burned fuel.

As the global community shifts away from fossil fuels towards more environmentally friendly energy alternatives, there is an escalating demand for sophisticated energy storage solutions. Solid-State Batteries (SSBs) have emerged as a promising advancement, presenting a superior substitute to conventional lithium-ion batteries. This review provides an in-depth examination of SSBs, emphasizing their enhanced energy density, safety, and longevity. We evaluate conventional cathode materials, including lithium cobalt oxide (LiCoO2), lithium manganese oxide (LiMn2O4), and lithium iron phosphate (LiFePO4). Additionally, we introduce emerging materials such as sulfides, oxides, and air-based cathodes, discussing their benefits, limitations, and their congruence with solid electrolytes. Special attention is devoted to the structural fine-tuning of cathode ma-terials, investigating approaches like nanostructuring, surface coatings, and composite strategies to counteract issues such as restricted conductivity and structural volatility. The review critically analyzes the electrical and thermal properties of these materials, which are essential for battery safety and efficacy. Moreover, we present a comparative assessment of cathode materials based on performance indicators and identify prevailing research voids and hurdles in the commerciali-zation of SSB cathodes. Concluding, we suggest prospective research directions and innovations, underscoring the revolutionary potential of SSB technologies in paving the way for a sustainable energy horizon.

In this study, the objective is to analyze the economic viability of municipal household solid waste (organic matter + paper) for the production of gas, coke and biofuel through the pyrolysis and distillation process. The waste was collected in the city of Belém do Pará-Brazil and pre-treated at UFPA. The analyzed fraction (organic matter + paper) was subjected to pre-treatment of drying, crushing, sieving and was subsequently subjected to proximate characterization and finally pyrolysis of the organic fraction (organic matter + paper) in a fixed bed reactor. Initially, it was necessary to review the literature and with the yields obtained by pyrolysis of the frac-tion, economic feasibility analyzes were carried out. The economic indicators for evaluating the most viable pyrolysis process were: simple payback, discounted payback, net present value (NPV), internal rate of return (IRR), and profitability index (IL). The analysis of the indicators showed the economic viability considering an analysis horizon of 10 years, of materials based on organic material and paper. The break-even point obtained was 0.96 US$/L and the minimum biofuel sales price (MFSP – “Minimum Fuel Sale Price”) obtained in this work was 1.30 US$/L. The sensitivity analysis demonstrated that material costs (organic matter + paper), bio-oil yield, total project investment and electricity, respectively, are the variables that most affect the mini-mum biofuel sales price (MFSP).

In recent years, the use of solid waste fillers to partially replace natural fillers in asphalt mixtures to produce high-performance asphalt mixtures has received widespread attention. However, differences in the material properties of solid waste fillers remain a problem for this recycling method. To address this issue, limestone powder in asphalt mixtures was replaced by three solid waste fillers (steel slag powder, tailings powder and calcium carbide slag powder) in this study. The chemical composition of the fillers was first characterized to assess the homogeneity of the material. Then, AC and SMA asphalt mixtures were designed and produced and characterized for wet stability. The results showed that asphalt mixtures with solid waste fillers were superior to LP asphalt mixtures in terms of resistance to water damage, and steel slag powder showed the best improvement in moisture stability of asphalt mixtures. The optimum substitution of solid waste filler for limestone filler was 25%. In addition, the moisture stability of asphalt mixture with limestone filler was significantly improved with the addition of anti-stripping agents. In contrast, the moisture stability of asphalt mixtures with solid waste filler was slightly improved. Solid waste fillers could be used in asphalt mixtures and have a similar function as the anti-stripping agent. In summary, the use of solid waste fillers to replace mineral fillers in asphalt mixtures is a reliable, value-added, recycling option.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

Currently, most plastic waste stems from packaging materials, with a large proportion of this waste either discarded or used to derive fuel. Accordingly, there is growing interest in the use of pyrolysis in the context of chemically recycling non-recyclable (i.e., via mechanical means) plastic waste into petrochemical feedstock. The aim of this study is to use kinetic analyses to elucidate the pyrolytic properties of solid recovered fuel (SRF) produced using two types of reactors, namely, fixed bed and fluidized bed reactors. From the kinetic analysis, the activation energy corresponding to the rate of pyrolysis reaction conversion was obtained. In conclusion, we found that the pyrolysis occurs more vigorously in fluidized bed reactors compared to fixed bed reactors.

Solid waste management is challenging in many countries, especially developing economies. The impacts of the pandemic continue to be felt and have indicated secondary impacts on waste management. This work draws on data on household solid waste (HSW), healthcare waste (HCW), and recyclables collected in the Rio de Janeiro municipality, analyzed from January 2018 to December 2022. As expected, the collection of HCW in Rio de Janeiro municipality experienced a noticeable increase in 2020 and 2021, with an average of 46.9 tons and 54.3 tons collected, respectively. Notably, 2021 saw a significant 30% increase compared to 2019 (p-value<0.001). No significant difference was observed in recyclables collected from 2018 to 2021. The average recyclable amount was 3,638 and 3,747 tons per month in 2020 and 2021. In contrast, the monthly amount was equal to 4,819.5 tons in 2022, representing an increase higher than 32% compared to previous years (p-value<0.05). Our findings can be used to adapt and improve waste systems to cope with similar emergency scenarios in the future, serving as a template for municipalities with similar challenges.

Any Hospital’s primary goal is to restore human health and save lives through health services provided to patients, but at the same time, hazardous wastes are produced. Inconsistent management of unsafe wastes might cause adverse effects and other issues to workers, the environment and public health. Segregation is considered the critical stage for a successful Healthcare Waste Management. Mixing hazardous waste with non-hazardous waste will be avoided by correctly applying practices at the segregation stage. This study aimed to assess personnel’s knowledge about Infectious Medical Waste and segregation practices used at six wards in Nicosia General Hospital. An analytical cross-sectional study was conducted, and data were collected through a structured self-administered questionnaire. The Statistical Package of Social Science (SPPS) version 25 was used with a minimum statistical significance α=0.05. The study population was nurses, nurse assistants, ward assistants and cleaners working at the study wards. Out of 191 questionnaires, 82 were received, with a response rate of 42.93%. Most participants were female (72%) and nurses (85,4%). Participants had medium to good knowledge about Infectious Medical Waste management and good knowledge regarding segregation practices applied in their ward. Segregation was not carried out as it should have since most participants stated that Infectious Medical Wastes were mixed with non-hazardous waste. Correct answers given by the participants regarding color-coding of different Healthcare Waste categories was 67.5%, and only four answered correctly to all questions. Although participants knew segregation practices and the colour-coding process applied for Healthcare Waste, they didn’t use them satisfactorily. They applied methods regarding segregation without specific training, knowledge and guidance. Due to the issue's importance, training programs must be implemented and performed.

In this paper we report on the use of an in-house developed solid-state hybrid microwave and radiofrequency generator operating at frequencies of 2.45 GHz and/or 480 kHz for cancer ablation in various tissues. The generator has demonstrated increased accuracy due to its custom-designed hardware, which incorporates the latest technologies and algorithms to control the emitted power versus temperature profile of the treated sample. In particular, the hybrid generator incorporates control systems based on impedance or reflected power measurements that allow controlled ablation without causing unwanted carbonisation and without including areas where tissue damage is not desired. Tests performed ex-vivo on chicken breast and bovine liver show that radiofrequency ablation (RFA) is very effective for performing controlled ablations with minimally invasive probes, such as cardiac pathologies, small lesions, tissues with particular composition, while microwave ablation (MWA) is optimal for performing large ablations in highly vascularised tissues, such as liver cancer, where it is necessary to achieve higher temperatures.

Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.

Personal Information Management Systems (PIMS) are acquiring a prominent role in the data economy by promoting services that help individuals to have more control over the processing of their personal data, in line with the European data protection law. One of the highlighted solutions in this area is Solid, a new protocol that is decentralizing the storage of data, through the usage of interoperable Web standards and semantic vocabularies, to empower its users to have more control over the processing of data by agents and applications. However, to fulfill this vision and gather widespread adoption, Solid needs to be aligned with the law governing the processing of personal data in Europe, the main piece of legislation being the General Data Protection Regulation (GDPR). To assist with this process, we analyze the current efforts to introduce a policy layer in the Solid ecosystem, in particular, related to the challenge of obtaining consent for processing personal data, focusing on the GDPR. Furthermore, we investigate if, in the context of using personal data for biomedical research, consent can be expressed in advance, discuss the conditions for valid consent and how it can be obtained in this decentralized setting, namely through the matching of privacy preferences, set by the user, with requests for data and whether this can signify informed consent. Finally, we discuss the technical challenges of an implementation that caters to the previously-identified legal requirements.

By the end of 2023, biowaste must be completely separated or recycled at source based on the EU legislation. Separate biowaste collection and valorisation towards biofuels could play an essential role in the biobased circular economy. In this context, the principal goal of this paper was to demonstrate in pilot scale the technological solution of bioethanol production via the utilisation of urban source-separated biowaste within the city context of Athens, Greece. More specifically, the main aim was the demonstration of a pilot system in continuous operation (over 10 operating cycles) with real feedstock – wet separately collected biowaste. From the 11 pilot trials performed with wet feedstock, the mean starch and cellulose degradation of the pilot trials amounted up to 80.69±16.27% and 79.41±10.37% respectively, while the bioethanol yield was 74.05±6.82%. The latter was comparable to that of more intensive pretreatment methods. Homogenization and shredding that was applied in this study, stand as promising and cost-effective pretreatment methods for bioethanol production from wet feedstock. Further research is needed to optimize conditions and evaluate scalability. Nevertheless, pilot scale testing is a crucial step in the development and deployment of this technology since it serves as a bridge between laboratory research and full-scale implementation, offering a practical and controlled environment to validate and optimize the technology while minimizing risks and uncertainties.

In road construction, before applying an asphalt or concrete surface, the ground must be compacted and stabilized. There are two basic methods of soil stabilization: in situ and in a stationary node (ex-situ). The method of performing stabilization in place (in-situ) is the most frequently used method due to its convenience and lower price. The most popular type of binder for stabilization is a hydraulic binder (most often cement and various ashes). Such stabilization is performed at a depth of 10-50 cm, achieving the desired load-bearing parameters. In order to improve them, various chemical additives for stabilization are often used, such as ion exchange compounds, additives based on sulfuric acid, additives based on vinyl polymers or even organic additives using lignosulfonates. However, the use of such additives is associated with much greater costs and environmental burden, resulting in seeking for cheaper and equally effective alternatives. The win-win situation would be for instance recycling the problematic waste-based materials that on one hand are landfilled or impossible to recycle and on the other hand cause problems for the waste producers. Therefore, an interesting issue is the production of stabilization additives from various types of waste materials. As a result of the extensive testing of various waste-based materials blends with soil, the mechanical (compressive strength after 7 and 28 days) and hydraulic (capillary rise, water absorption, frost resistance) soil properties were measured. The optimization process led to obtaining additives compositions ensuring the best strengthening and sealing properties. These were for sandy soil: Pure foil (wax emulsion), Pure foil (wax emulsion) + waste sulphuric acid, RDF from waste tires (wax emulsion), Pure foil (wax emulsion) + “by-pass” waste ash + NaOHx2 and for clayey soil: Pure foil (wax emulsion) + NaOH, Pure foil (wax emulsion) + waste sulphuric acid, Tequant, Pure foil (wax emulsion).

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

Environmental perception is a powerful tool for identifying community needs and potential within their surroundings. This study assessed tourists' environmental perception regarding solid waste and its impact on the Hurtado balneary, located in Valledupar, Colombia. From May to July 2023, the investigation delved into the environmental attitudes and behaviors of 769 balneary users by employing a combination of observation, photographic documentation, and a comprehensive 21-question online survey. The findings unveiled compelling insights: an overwhelming 98.8% of participants acknowledged the adverse effects of solid waste on the environment, with an impressive 98% demonstrating a willingness to participate in waste management efforts. Alarmingly, 42.13% exhibited limited awareness of waste management practices, reflecting a lack of public interest and commitment (41.61%). Statistically significant disparities emerged: 59% of waste items were not appropriately disposed of in designated receptacles. Reasons for this included a lack of a sense of belonging (50.2%) and inadequate environmental education (45.6%). 96% expressed the need for river conservation signage, while 59.8% had not engaged in environmental training. The implications of these results extend beyond the Hurtado balneary, potentially informing solid waste management strategies in other aquatic environments. Furthermore, this investigation aligns with three critical Sustainable Development Goals: SDG 12, emphasizing responsible consumption and production; SDG 13, addressing climate action; and SDG 15, advocating for life on land and below water. Keywords: Tourism; solid waste; surface water; environmental management.

An estimated 38 million individuals, out of a total population of around 126 million, reside in urban areas of Bangladesh. The surge in urbanization and water consumption has led to a significant rise in waterborne sanitation systems within the country. One cost-effective solution for wastewater treatment is the utilization of septic tanks, which operate as anaerobic reactors, with their efficiency being closely tied to temperature conditions. This research focuses on evaluating the organic removal capabilities of a septic tank located on the Khulna University of Engineering and Technology (KUET) campus. The results show that a septic tank's ability to remove organic matter depends on the temperature, with higher temperatures making the removal process more effective. Additionally, the Total Suspended Solids (TSS) levels were observed within a range of 110–280 mg/L, 200–1030 mg/L, 160–880 mg/L, and 190–220 mg/L for the 1st, 2nd, and 3rd chambers, respectively. The maximum recorded pH values were 7.14, 7.13, and 7.11, while the minimum pH values were 7.06, 7.05, and 7.04, corresponding to the same chambers. Furthermore, the organic removal efficiency concerning dissolved oxygen (DO), nitrate (NO3-N), and pH levels remained within acceptable limits. These results suggest that a simple treatment unit like a septic tank can effectively render previously unacceptable and unhygienic water suitable for safe disposal and potential reuse, ultimately improving the management of septic tank wastewater.

This study deals with the computational analysis of the kinetic processes of a microbial electrolysis cell assisted-anaerobic digestion (MEC-AD) treating raw-waste activated sludge (WAS), comparatively with a conventional AD, as well as the effect of the Organic Loading Rate (OLR) on the system’s performance. The aim was to derive a single kinetic and mathematical model for the study of the MEC-AD, using the ADM1 framework, which can be utilized to extract the effect of an applied potential on the kinetics of AD. The experimental data were obtained from the long-term, continuous operation of two identical reactors (an AD and a MEC-AD), which were operated at different OLRs (1.1, 1.7 and 2.9 gCOD/(L*d)). The results showed that the MEC-AD yielded improved biomass yields, substrate consumption kinetics and 1st order disintegration kinetics, with a predominant contribution to disintegration of complex particulates, comparatively with the AD. Moreover, it enabled operation at higher OLRs (achieving the highest divergence from the AD at the OLR of 4.14 gCOD/(L*d)), therefore accelerating sludge treatment, as well as an improved performance at an increased solids retention time (SRT). These findings can serve as a quantitative guide for the effects of the operating parameters on the raw-WAS-fed MEC-AD performance.

This article presents the results of studies of the structure and conductive properties of Na3Fe2(PO4)3 polycrystals synthesized by solid-phase and melt (using concentrated optical radiation) methods. It has been established that with the melt method, the synthesis of the material occurs under significantly nonequilibrium temperature-gradient conditions, which leads to the creation of deformations in the sample that contribute to an increase in ionic conductivity. The ability of the Na3Fe2(PO4)3 structure to adapt to anomalous deformations that occur under temperature-gradient conditions indicates the elasticity of the crystalline framework {[Fe2(PO4)]3-}3∞. Through a comparative assessment of the structural parameters and conductive properties of these materials, it is shown that polycrystals obtained by the melt method have a better texture and greater ionic conductivity. The advantage of this method is that the duration of the synthesis of α-Na3Fe2(PO4)3 is halved. It is concluded that this method is applicable to obtain effective polycrystals of other compositions.

An inorganic solid electrolyte is the most favorable candidate for replacing flammable liquid electrolytes in lithium batteries. Lithium Lanthanum Zirconium Oxide (LLZO) is considered as a promising solid electrolyte due to its safe operating potential window (0-5V) combined with its good electrochemical stability. In this work, 250 g batches of pre-sintered Tadoped (Li7La3Zr1.6Ta0.4O12, TaLLZO) were synthesized for bulk production of dense LLZO electrolyte. A simple two-step thermal treatment process was developed. The first thermal step at 950 °C initiates nucleation of LLZO carefully controlling process parameters such as heating atmosphere, temperature and dopant concentration. In the second thermal step at 1150 °C, sintered discs were obtained as solid electrolytes, with relative densities of 96%. X-ray diffraction analysis confirmed the phase purity of the sintered TaLLZO disc, and refined data was used to calculate the lattice parameter (12.944 Å). Furthermore, the presence of the Ta dopant in the disc was confirmed through X-ray photoelectron spectroscopy (XPS) analysis. The ionic and electronic conductivity values of TaLLZO disc were 104 S cm-1 and 10-10 S cm-1, respectively. These values confirm that the prepared (Ta-LLZO) discs exhibit ionic conductivity while being electronically insulating, being suitable for use as solid electrolytes with the requisite electrical properties.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

Acerola (Malpighia spp.) is a tropical plant genus of shrubs and trees whose fruit is rich in nutrients and bioactive compounds. However, its production generates significant waste that could pose an environmental issue. This review aims to summarize recent research on the potential uses of acerola wastes, including the extraction of bioactive compounds such as polyphenols, carotenoids, and pectins, as well as the development of materials such as nanomaterials, chitosan, and biofuels. Additionally, the paper discusses the potential medical applications of acerola wastes, such as wound healing, antioxidant, and anticancer effects. Finally, the paper explores the challenges and opportunities of using acerola waste as a sustainable source of raw materials and energy. The findings suggest that acerola waste could be a valuable resource for developing high-value products and promoting sustainable production practices in the fruit industry.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

The paper presents the relationship between the efficiency of the process of skin onion peeling and its effect in the form of waste. The research was carried out on a pilot test stand for onion peeling. The process variables were compressed air with a pressure of (p) and valve controlling opening time of flow (t). The experiment took into account the influence of the onion diameter (d0) and its hardness (H). The obtained results were subjected to statistical analysis. Standard deviations were of the percentage loss of onion mass in the form of the skin removed of onion peeling in the process in relation to obtained aver-age values. Tukey's multiple comparison test was performed in order to identify the importance of individual process variables on the final effect of onion peeling. This was the basis for the development of a predictive model in the form of a nonlinear regression Mp=f(p,t,d0,H), which is a mathematical description of the peeling onion skin process . Finally, the response surface area of relationship between analyzed variables was determined. The results of research showed the peeling efficiency of the onion and waste of skin mass depend on the compressed air pressure. Extending the onion blowing time does not improve the process efficiency, while the hardness and size of the onion are irrelevant to the process.

The performance of recycled aggregate concrete deteriorates due to the defects of adhesive mortar, pores and cracks on the surface of recycled aggregate. It is of great engineering significance to modify the reclaimed aggregate to improve its performance and adaptability. In this paper, the physical and chemical properties of waste concrete recycled aggregate are reviewed. Then, the existing modification methods and technologies of recycled aggregate, including physical, chemical and biological methods, are reviewed. Finally, the existing problems of the current modification technology are summarized, and the future research direction is proposed. It is expected to provide a new idea and method for the modification of waste concrete recycled aggregate.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

In South Korea, demolition waste (DW) management has become increasingly significant owing to the rising number of old buildings. Effective DW management requires an efficient approach that accurately quantifies and predicts the generation of DW (DWG) of various types, which necessitates access to the required information or technology capable of achieving this. Hence, we developed an artificial intelligence-based model that predicts the generation of ten DW types, specifically from buildings in redevelopment areas. We used an artificial neural network algorithm with < 10 neurons in the hidden layer to derive individual input variables and optimal hyperparameters for each DW type. All DWG prediction models achieved an average validation and test prediction performance (R²) of 0.970 and 0.952, respectively, with their ratios of percent deviation ≥ 2.5, ver-ifying them as excellent models. Moreover, a Shapley additive explanations analysis revealed that DWG was most impacted by the floor area for all the DW types, with a positive correlation with DWG. Conversely, other factors showed either a positive or negative correlation with DWG de-pending on the DW type. The study findings will enable demolition companies and local gov-ernments in making informed decisions for efficient DW management and resource allocation by accurately predicting the generation of various types of DW.

Thermoelectric (TE) waste heat recovery has attracted significant attention over the past decades, owing to its direct heat-to-electricity conversion capability and reliable operation. However, methods of system-level TE design optimization for specific application systems have not been thoroughly investigated. This work theoretically studies the performance optimization and exergy analysis of TE systems for recovering waste heat from the exhaust ducts of a gas turbine power plant. A numerical tool has been developed to solve the coupled charge and heat current equations with temperature-dependent material properties and convective heat transfer at the interfaces. Our calculations show that at the optimum design with 50 % fill factor and 6-mm leg thickness made of state-of-the-art Bi2Te3 alloys, the proposed system can reach power output of 10.5 kW for the TE system attached on a 2 m-long, 0.5 x 0.5 m2-area exhaust duct with system efficiency of 5 % and material cost per power of 0.23 $/W. Moreover, our extensive exergy analysis reveals that only 1 % of the exergy content of the exhaust gas is exploited in this heat recovery process and the exergy efficiency of the TE system can reach 8 % with improvement potential of 85 %.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

The efficient extraction of phthalate acid esters (PAEs) is challenging due to their extremely low concentration, complicated matrices and hydrophilicity. Herein, hol-low microspheres, as an ideal coating, possesses significant potential for solid-phase microextraction (SPME) due to their fascinating properties. In this study, multi-walled carbon nanotubes hollow microspheres (MWCNTs-HMs) were utilized as a fiber coating for the SPME of PAEs from tea beverages. MWCNTs-HMs were ob-tained by dissolving the polystyrene (PS) cores with organic solvents. Interestingly, MWCNTs-HMs well maintain the morphology of the precursors MWCNTs@PS. The layer-by-layer (LBL) assembly of MWCNTs on PS microsphere templates was ac-quired through electrostatic interactions. Six PAEs, di-ethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzyl butyl phthalate (BBP), di-2-ethylhexyl phthalate (DEHP) and di-n-octyl phthalate (DOP), were se-lected as target analytes for assessing the efficiency of the coating for SPME. The stirring rate, sample solution pH and extraction time were optimized by using the Box-Behnken design. Under optimal working conditions, the proposed MWCNTs-HMs/SPME was coupled with gas chromatography-tandem mass spec-trometry (GC-MS/MS) to achieve high enrichment factors (118–2137), wide linearity (0.0004-10 μg L-1), low limits of detection (0.00011-0.0026 μg L-1) and acceptable recovery (80.2%-108.5%) for the detection of PAEs. Therefore, the MWCNTs-HMs coated fibers are promising alternatives in the SPME method for the sensitive detec-tion of PAEs at trace levels in tea beverages.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

SPME analysis of the scent Ophrys orchids gave the following results: O. apifera: benzyl benzoate, -copaene, caryophyllene, and cyclosativene. O. crabronifera subsp. biscutella: pentadecene, pentadecane, heptadecane, nonadecane, and heinecosane. O. bertolonii subsp. bertolonii: pentadecane, heptadecane and nonadecane. O. passionis subsp. garganica: i-propyl palmitate, caryophyllene, pentadecane, and heptadecane. O. holosericea subsp. apulica: -copaene, pentadecane, caryophyllene, and heptadecane. O. lacaitae: -copaene, pentadecane, heptadecane, and caryophyllene. O. bombyliflora: cyclosativene, pentadecane, and ethyl dodecanoate. O. insectifera: 8-heptadecene, pentadecane, and heptadecane. O. lutea: heptadecane, 8-heptadecene, nonadecane, and docosane. O. tenthredinifera subsp. neglecta: -copaene, caryophyllene, and i-propyl palmitate.

Organic fertilizers are fertilizers made from organic materials which are partly or wholly derived from waste materials, the function of these fertilizers is to improve the physical, biological, and chemical properties of the soil, these fertilizers are processed through the composting process, these fertilizers are very much needed because they are difficult to obtain at a high price. expensive. This study aims to obtain data on the growth and yield of sweet corn, due to the use of agricultural waste as organic fertilizer. The research method was experimentally consisting of 5 treatments and 5 replications; ie P0 = Without organic fertilizer (control) P1 = Dosage of organic fertilizer 2.5 tons/ha, P2 = Dosage of organic fertilizer 5 tons/ha P3 = Dosage of organic fertilizer 7.5 tons/ha, P4 = Dosage of organic fertilizer 10 tons /ha using a Randomized Block Design (RBD) The results showed that organic fertilizer had a significant effect on plant height aged 30, 40 and 50 DAP, had a very significant effect on cob length at a dose of 10 t.ha-1 and, had no significant effect on cob weight, will still have a high weight of 350 g.cob-1 From this description it can be concluded that organic compost can be used as a substitute for chemical fertilizers which provides an increase in the growth and production of sweet corn plants at the use of 10 tons/ha.

This paper presents the results of investigations on the pyrolysis of tyres waste in a laboratory fixed bed batch reactor. The results regarding the influence of either the reaction temperature (425, 450, 475, and 500 °C) and the flow of the inert gas (0, 100, 300, and 500 mL/min) on products yield (referred to pyrolysis of waste tyres) are also considered and discussed. On the basis of the above mentioned findings, the most appropriate experimental conditions were selected to contribute to a higher yield of pyrolysis oil. The sample of pyrolysis oil obtained from the experiments carried out in the selected optimal conditions (reaction time 120 min, temperature 450 °C and the inert gas flow of 100 mL/min) was subjected to a calorimetric and infrared spectroscopy analysis. The results of IR spectroscopy analysis on this oil sample showed the following content in percentages (by mass): 32.59 % of aromatics, 51.06 % of paraffins and 16.35 % of naphthenes. The pyrolysis oil so obtained has a high calorific value (42 MJ/kg) and a low sulfur content (0.41 % by mass), which makes it an excellent raw material for energy production. The solid product, i.e. pyrolysis char or carbon black, has the potential to be used as an adsorbent or catalyst support after an activation process, which changes its irregular pore structure to a more voluminous one, making the overall structure more crystalline and symmetrical. Pyrolysis coal has a fairly high calorific value of 31 MJ/kg, when compared to typical solid fuels, so it can be used in energy production or as a feedstock for the gasification process.

Derelict asbestos mine sites in South Africa pose a considerable risk to human, environmental and socio-economic health. Comprehensive mineralogical and geochemical datasets for the existing hazardous geological materials still exposed in Southern African derelict asbestos mines remain largely non-existent, as very little published and up-to-date literature is available. In this study three representative types of asbestos mineral fibres from derelict asbestos mines in Southern Africa, namely chrysotile from Havelock mine, amosite from Penge mine and crocidolite from Prieska mine are characterized mineralogically and geochemically to critically evaluate real-life hazards in rural and asbestos-fibre contaminated regions. The samples were examined using polarising light microscopy, X-ray fluorescence (major and trace elemental analysis), X-ray diffraction (including Rietveld refinement), specific surface area analyses and bio-durability tests. Data are discussed in view of their potential toxicities on both human health and the environment in the context of developing countries. Finally, information on the mineralogical and geochemical status of asbestos mine waste and its importance as baseline data for rehabilitation considerations is also evaluated.

The agricultural ecological environment provides an important resource guarantee for social development. The extensive management mode of agriculture in China has not fundamentally changed; the contradiction between production and governance is still prominent, and the management of agricultural surface pollution has a long way to go. Based on the data of 547 rural households in Jiangxi province, this paper uses the Ordered Logit, 2SLS, and moderation effect model to analyze the mechanism between social norms (SNs) and rural households’ (RHs) disposal of pesticide packaging waste (PPW) and to test the moderation effect of environmental regulation (ER) in the influence path of SN to RHs’ disposal of PPW. The results show that (1) descriptive and directive norms can promote RHs not to litter PPW. However, the role of surrounding crowd supervision (directive norms) is more obvious than the behavior of the surrounding crowd (descriptive norms). The consistent conclusion was still obtained after the robustness test and endogeneity treatment. (2) The results of the moderation effect test showed that reputational incentives strengthened the promotional effect of directive norms on RHs' behavior of not littering PPW; punitive regulation hindered the promotional effect of descriptive norms on RHs' behavior of not littering PPW. Based on the findings of the study, the following policy recommendations are put forward: continue to strengthen the guidance and soft binding force of informal institutions such as SNs; accurately locate the target groups and formulate differentiated measures; pay attention to the complementary nature of formal and informal institutions, and reasonably formulate environmental regulations to fit in with SNs.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

A layout of urban waste fired zero emission power plant is described in this paper. The principle of layout, which comes from similar coal-fired plants retrieved from the literature, integrates gasification with a power generation section, and implements two parallel conversion processes, one supplied by the heat of the gasifier consisting of a thermoacousticmagnetohydrodynamic (TAMHD) generator, while in the second one the syngas is treated in order to obtain almost pure hydrogen, which is fed to fuel cells. The CO2 deriving from the oxidation of Carbon base is stocked in liquid form. The novelty of the proposed layout lies in the fact that the entire conversion is performed without solid moving parts. The resulting plant avoids any type of emissions in the atmosphere, increases mechanical efficiency as compared to traditional plants, thanks to the absence of moving parts, nonetheless, resolving at its root the ever-increasing waste-related pollution problems.

Anthropogenic chemicals are fundamental to our standard of living in modern society. Unfortunately, some chemicals are persistent and can enter waste streams and ultimately the environment. Commonly used household products including pharmaceuticals and personal care products are an important source of contaminants. The aim of this study was to develop an “Up-the-pipe Solutions” framework to raise awareness about the presence and potential risks of chemicals found in household products to reduce their levels in waste streams or substitute them with less harmful alternatives. This approach based on The Natural Step framework and the concept of essentiality recognises the importance of engaging the community to raise awareness around the consequences of our daily activities and behavioural patterns that can lead to the release of persistent contaminants in main waste streams from the kitchen and bathroom and green wastes we generate.

The aim of this study is to examine an efficient and environmental friendly process for hydrolyzing starch, an industrial-derived by-product of the potato processing industry, and to use the produced hydrolysates as substrates for methane production. A full factorial experiment was designed and the optimal concentrations of FeSO4·7H2O, H2O2 and temperature were determined obtaining a yield of 99.5%, with a total carbohydrates content equal to 28.65 g, when the input parameters were at their high level: FeSO4·7H2O 1.00g/L, H2O2 0.51 g/L and temperature 70.0oC. The hydrolysis kinetics were also examined revealing that temperature was the most important factor among the three optimization parameters. Furthermore, biodegradability tests were carried out to measure the methane production potential from the produced hydrolysates. The specific methanogenic activity was reached 0.669 g CODCH4/gVSS-day proving the effectiveness of the hydrolysis process and highlighting the potential of this food manufacturing by-product for bioenergy production. A preliminary cost analysis showed that a small investment for utilizing the starch in an existing wastewater treatment facility of a potato processing industry becomes profitable before the end of the 3rd year obtaining a NPV 37.5% higher than the NPV of the current utilization scenario.

The phosphogypsum (PG) pile of solid waste is of immense proportions and poses a grave threat to the ecological environment, with its reserves steadily increasing year after year. The urgent need for large-scale consumption and high-quality utilization of PG in industrial production has become apparent. The present study provides a comprehensive analysis of the correlation be-tween the macroscopic mechanical properties and microstructure of PG, elucidating the crystal morphology characteristics in different phases and outlining the crystallization preparation pro-cess. By integrating the physical and chemical properties of diverse PG phases with the intricacies associated with its preparation process, it is imperative to explore avenues for its high-value utili-zation, investigate possibilities for industrial-scale production, and analyze and predict the appli-cation trends and developmental directions in comprehensive PG utilization. These endeavors hold immense significance in guiding the realization of resource utilization potential inherent in PG.

The macro-litter (plastic) sea bottom pollution of 14 city harbors and marinas in North Africa and in the western Baltic Sea was investigated using a new simple mobile underwater camera system. The study was complemented by a harbor manager survey and 3D-hydrodynamic transport simulations. The average pollution in German marinas was 0.1 particles/m² sea floor (0.04–1.75). The pollution in North African marinas on average was 7 times higher (0.7 particles/m²) and exceeded 3 particles/m² in city center harbors. The resulting &gt;100,000 litter particles per harbor indicate the existence of a problem. With 73%-74%, plastic particles are dominating. Existing legal and management frameworks explain the lack of plastic bottles and bags on sea floors in Germany and are one reason for the lower pollution levels. Items that indicate the role of untreated sewage water were not found. Harbor festivals seem not to be quantitatively relevant for open sea bottom pollution. Our method tends to underestimate the pollution level. Model simulations indicate that storms can cause litter reallocations and sediment cleanings. However, marina sea floor monitoring is recommendable, because it addresses pollution hot-spots, is cost-effective and takes place close to emission sources. Further, the effectiveness of land-based pollution reduction measures can easily be assessed.

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

The creation of mitochondria-targeted vector systems is a new tool for the treatment of socially significant diseases. Phosphonium groups provide targeted delivery of drugs through biological barriers to organelles. For this purpose, a new class of alkyl(diethylamino)(phenyl) phosphonium iodides (bromides) 1 containing one, two, or three diethylamino groups were obtained by the reaction of alkyl iodides (bromides) with (diethylamino)(phenyl)phosphines under mild conditions and high yields. The structure of compounds 1 was established by NMR and XRD. In vitro a high cytotoxicity against the lines M-Hela, HuTu 80, PC3, DU-145, PANC-1 and MCF-7 was found. Selectivity index are in the range of 0.06-4.0 M (SI 17-277) for the most active compounds. ROS production, mitochondrial localization and the process of cellular apoptosis were investigated. Decorated by 1 of lipid systems (liposomes and solid lipid nanoparticles) improve the cytotoxicity and a decrease in toxicity against normal cell lines. Compounds 1 induce apoptosis proceeding along the mitochondrial pathway. Aminophosphonium salts 1 also exhibit a high selective activity against the Gram-positive bacteria strains S. aureus 209P, B. segeus 8035, including methicillin-resistant strains of S. aureus (MRSA-1, MRSA-2), comparable to the activity of the fluoroquinolone antibiotic norfloxacin. A moderate in vivo toxicity in CD-1 mice was established for the lead compounds.

The extraction method for simultaneously analyzing fatty acids (Myristic acid, cis-Palmitvaccenic acid, Palmitic acid, Palmitic-9,9-d2 acid, Oleic acid, Stearic acid and Stearic-2,2-d2 acid) related to biodiesel fuel in large algae was developed. The introduction of trimethylaminoethyl (TMAE) derivatives into the hydroxyl group (-OH) functional group of the analyte was able to improve ionization and obtain high sensitivity. Liquid Chromatography (LC) was used to investigate the optimal mobile phase composition and flow rate for the separation of five derived fatty acids. In this study, a solid phase extraction (SPE) column was introduced for efficient extraction of fatty acids, and the optimal conditions for SPE were set by comparing the recovery rate according to the solvent for each step (loading, washing, and elution) of SPE from macroalgae.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

Using straightforward and cost-effective methods, persimmon leaves were converted into a high-quality powder. This powder was applied as an adsorbent for the removal of Cu(II) and Cd(II) from aqueous solutions. Scanning electron microscopy (SEM) indicated the presence of particles with non-homogeneous sizes and rough texture. Elemental analysis and the EDX technique confirmed the presence of elements such as sulfur, phosphorus, nitrogen, and oxygen. The results of ¹³C nuclear magnetic resonance (¹³C-NMR), obtained through the cross-polarization technique, suggest the presence of groups containing sulfur and oxygen. Infrared spectroscopy (FTIR) indicated the existence of amine and hydroxyl groups. The material was used in solid-phase extraction of Cu(II) and Cd(II) in batch experiments, and its adsorption capacity was evaluated as a function of time, pH, and analyte concentration. Kinetic equilibrium was reached within 5 minutes, and the experimental data were fitted to the pseudo-second-order kinetic model. The optimum pH for adsorption of both metal species was observed to be around 5.0. The adsorption isotherms were adjusted using the modified Langmuir equation, and the maximum amount of metal species extracted from the solution was determined to be 0.213 mmol g^-1 for Cu(II) and 0.215 mmol g^-1 for Cd(II), with high linear correlation coefficients for both metals. The persimmon leaves are typically abundant during the growing season, and since they are seasonal, the Diospyros kaki L.f. tree undergoes the natural process of leaf abscission, ensuring the availability of leaves for application.

This study explores the potential of titanium disulfide (TiS2) as an active material for aqueous calcium-ion batteries (CIBs). We investigate the electrochemical redox reactions of calcium ions within TiS2 and assess its suitability for use in aqueous CIBs. Additionally, we examine the im-pact of different electrolyte concentrations on TiS2 electrode reactions. Our findings reveal that TiS2 exhibits distinct charge-discharge behaviors in various aqueous calcium-ion electrolytes. Notably, at higher electrolyte concentrations, TiS2 effectively suppresses the hydrogen genera-tion reaction caused by water decomposition, demonstrating its potential as an active material for aqueous CIBs. In-situ X-ray diffraction analysis confirms the intercalation of Ca2+ ions be-tween TiS2 layers during charging. This confirmation is groundbreaking, as it represents the first experimental evidence of calcium ions being electrochemically inserted between TiS2 layers from aqueous solutions, signifying a previously unreported achievement and strongly suggesting TiS2's applicability in aqueous CIBs. X-ray photoelectron spectroscopy analysis further supports the formation of a solid electrolyte interphase (SEI) on the TiS2 electrode surface, contributing to the suppression of electrolyte decomposition reactions. Furthermore, we investigate the influ-ence of anions in the electrolyte on charge-discharge behavior. Our findings suggest that the choice of anion coordinated with Ca2+ ions affects SEI formation and cycling performance. Un-derstanding the role of anions in SEI formation is crucial for optimizing aqueous CIBs. In con-clusion, this research underscores TiS2's potential as an active material for aqueous calcium-ion batteries and emphasizes the importance of electrolyte composition in influencing SEI formation and battery performance. These findings contribute to the development of more sustainable and efficient energy storage technologies.

Although 4Ce4YSZ has high corrosion resistance, it faces challenges concerning sinterability and ionic conductivity. Therefore, we studied destabilization behavior caused by corrosion and oxygen vacancy ordering according to ZnO doping. The powders of (4Ce4YSZ)1-x(ZnO)x (x=0.5, 1, 2, 4 mol%) were synthesized through the sol-gel method. With the addition of ZnO, the cubic phase increased, and secondary phases were not observed. The (111) peak showed a higher angle shift in ZnO-doped 4Ce4YSZ compared to 4Ce4YSZ, and TEM-SAED revealed a reduction in the spacing of the (011)t plane, suggesting lattice contraction due to the substitution of the smaller Zn2+ (60 Å) for Zr4+ (84 Å) in the lattice. The local atomic structure analysis was conducted using EXAFS to investigate the oxygen vacancy ordering behavior. Zr K-edge Fourier-transform data revealed a decrease in the Zr-O1 peak intensity with an increasing amount o ZnO doping, indicating an increase in oxygen vacancies. The Zr-O1 peak position shifted to the right, leading to an increase in the Zr-O1 interatomic distance. In the Y K-edge Fourier-transform data, the Y-O1 peak intensity did not decrease, and there was little variation in the Y-O1 interatomic distance. These results suggest that the oxygen vacancies formed due to ZnO doping are located in the neighboring oxygen shell of Zn, rather than in the neighboring oxygen shells of Y and Zr. Impedance measurements were conducted to measure the conductivity, and as the amount of ZnO doping increased, the total conductivity increased, while the activation energy decreased. The increase in oxygen vacancies by ZnO doping contributed to the enhancement of conductivity and it is considered that these created oxygen vacancies did not interact with Zn2+ and did not form defect associations. Fluoride-based molten salts were introduced to the specimens to assess corrosion behavior in a molten salt environment. Yttrium depletion layers (YDLs) were formed on the surfaces of all specimens due to the leaching of yttrium. However, Ce remained relatively stable at the interface according to EDS line scans, suggesting a reduction in the phase transformation (cubic, tetragonal to monoclinic) typically associated with yttrium leaching in YSZ.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

The growing population with changing consumption patterns in developing countries is causing significant challenges with regards to solid waste management. Plastic wastes are particularly problematic, with single-use plastics leaking into the environment, including the marine environment, at an unprecedented rate. Approximately 80 percent of ocean plastics come from land-based sources or about 8 million tons are dumped into the ocean every year. Thailand was identified as one of the top 10 countries ranked by mass of mismanaged plastic wastes, with more than 60,000 tons per year entering the ocean through multiple outlets, including rivers. In the environment, plastic wastes can be degraded into small sizes (less than 5 mm), called microplastics (MPs), which could contaminate the ecosystems and the food chain, including foodstuffs and water supply. Tap water samples collected from a water supply treatment plant and Academic Institutions 1 and 2 in central Thailand were found to contain MPs about 304 ±90, 270 ±109 and 386 ±102 particles/L, respectively. In addition, MPs concentrations of 211 ±70 and 122 ±60 particles/L were also found in drinking water samples collected from commercial bottled water and membrane filtration water, respectively. The MPs sizes of 0-50 µm were most abundant in both the tap and drinking water samples whose shapes were mainly fragments and fiber. These data indicated potential health risks to the people who consume these water sources, and recommendations for health impacts minimization were proposed.

Effective solid waste management is crucial for protecting public health and the environment. Global concentration on finding sustainable methods of handling waste continue to top the list of most governmental-related project checklists. This paper provides a case study on the management of municipal solid waste in the cities of Karlsruhe, Germany and Navrongo, Ghana as developed and developing countries respectively. This study aimed at comparing and drawing lessons from how these two different cities manage their solid waste. The waste management system in Karlsruhe prioritizes waste separation, recycling, and a pay-as-you-throw system has led to an efficient and sustainable waste management system that minimizes waste and protects the environment. Karlshrue's adoption of a continual developmental plan structure focused on integrated WM concepts is credited with safeguarding the long-term viability of waste management in the city. In contrast, Navrongo's waste management system faces several challenges, including inadequate resources and infrastructure, traditional waste disposal practices, and the lack of well-planned waste management strategies. To improve effective solid waste management systems in Ghana, a collaborative approach involving the government, local organizations, and the community is necessary. This can include investing in infrastructure, implementing waste separation and recycling programs, and educating the public on the benefits of sustainable waste management practices. Learning from successful models like Karlsruhe can help accelerate the development of sustainable waste management practices in Ghana, and ultimately protect public health and the environment.

Cemeteries can be compared to landfills since their leachate, also known as necroleachate, can be transported and pollute groundwater, surface waters, and soils. In Brazil, the cemeteries management is the responsibility of states and municipalities, to ensure that they do not generate negative environmental impacts and risks to public health. This article aims to discuss Brazilian sanitary-environmental legislation relating to cemetery waste management. Among the Brazilian states, half have sanitary-environmental legislation for cemeteries, and between the municipalities, only 19 have specific legislation. The legislation is broad and has many gaps, leading to environmental vulnerability and risk of contamination for the people who live in the surrounding area.