Intercalation of noble metals can produce giant Rashba-type spin-orbit splittings in graphene. The spin-orbit splitting more than 100 meV has not yet been achieved in graphene on a metallic or a semiconductor substrate. Here, we report the p-type graphene obtained by Pt intercalation of zero-layer graphene on SiC substrate. The spin splitting of ∼200 meV was observed at a wide range of binding energies. Comparing the results of theoretical studies of different models with the experimantal ones measured by spin-ARPES, XPS and STM methods, we came to the conclusion that inducing giant spin-orbit splitting requires not only a fairly close arrangement of graphene to Pt layer, but also the presence of graphene corrugation caused by non-flat Pt layer. This makes it possible to find a compromise between strong hybridization and increased spin-orbit interaction. In our case, this is achieved by forming Pt submonolayer ordered on a nanometer scale under graphene.

The idea of an extension of life for CubeSats is proposed to reduce space debris in a low-earth orbit. In this work, a gripper is designed for geometry-based grasping in berthing tasks. The grasping operation is outlined for square- and rectangle-profiled CubeSats. Equilibrium conditions are used to choose fingertips shape and parameters for grasping the CubeSat body. A design scheme is proposed to provide the required accuracy. A design concept is developed into a lab prototype by using low-cost 3D printing technique, and a mock-up grasping task that is representative of the berthing operation is evaluated with the lab prototype. Center-mass hanging setup for the prototype and grasped body is used to evaluate the impact of grasping, partially replicating the conditions in space by reducing the effect of gravity on the system.

Meals on Wheels (MoWs) provide access to daily meals and social contact to adults with care and support needs.MoWs could be essential for the increasing rates of an ageing population and adults living with complex needs in England, yet many do not know that the service exists. This study aimed to explore the perceptions of MoWs service users, and people who refer them to MoWs (‘referrers’), with accessing and setting up the service in England, and what information would be valued when considering accessing MoWs services.Semi-structured interviews were conducted in May-July 2022 with seven service users and 21 referrers, recruited from four MoWs providers across England. Data were analysed using thematic analysis. Participants indicated various pathways into the service, but referrers (family members) were more likely to be the ones enquiring about, and setting up, MoWs for service users. Once an enquiry about MoWs had been made, the service was perceived as straightforward to set up.However, existing preconceptions and stereotypes about the service (e.g. bringing to mind ‘school meals’, aimed solely at older adults) were perceived to act as barriers to accessing MoWs.Information that participants deemed important to have available when deciding on whether to access MoWs related to the meals (e.g. nutritional value, variety, need for any preparation, catering for individual needs), the specific services provided (e.g. wellbeing checks, daily social contact), the reliability and flexibility of delivery, and the cost of services. These findings could inform MoWs providers’ public awareness strategies about MoWs, in order to facilitate referrals to the service for adults with care and support needs.

The article presents a methodology for modeling the impact of factors of both on-farm activity and environmental factors on the resulting indicators of an international company. The dataset includes the company's profit, revenue, valuation, share price, and market share from 2012 through 2022. This empirical period is optimal for such a type of modeling. Modeling the impact of carbon emissions factors on the resulting indicators is considered based on complex systems theory. Endogenous model variables include indicators of the development of the international company. Predefined model variables reflect the influence of both the external environment and internal factors on the development indicators of an international company. An approach of picture fuzzy rough sets based on time series of endogenous and exogenous variables can provide an opportunity to analyze and consider the consequences of feedback changes in the systems of which they are a part. Based on the results of the analysis of the model construction, it is concluded that picture fuzzy rough sets can be an excellent way to model interdependent social processes.

Since the Sustainable Development Goals (SDGs) came into effect, both UNESCO and other international organisations recommend empowering youth to implement the SDGs in universities. Getting started with the SDGs at university level is of special relevance in pre-service teacher training since future teachers are powerful agents of change in the lives of young people. Future teachers need to acquire competencies in sustainability to be able to promote meaningful changes in sustainable behaviour. To that end, holistic approaches to facilitate their acquirement need to be developed. The aim of this study is to explore which teaching methodologies are suitable for the development of competencies in sustainability in Higher Education (HE) and how to empower students to take a leading role in implementing the SDGs in universities. The participants in the study are a group of 23 students in pre-service teacher training. The experimental educational model used for the development of sustainable competencies consists of a methodological sequence of Project-Oriented Learning (POL) and a Cross-disciplinary Workshop on Sustainable Food. This study provides evidence that a holistic approach is appropriate for developing sustainable competencies and contributes to empowering students to implement SDG 12 at their university.

This research analyzed the impact of quality of service as perceived by Hapkido students on their exercise continuation and recommendation intentions. It also identified the measures to reduce the rate of student dropout, strengthen competitiveness, and create more efficient marketing strategies for consumer patterns that are rapidly diversifying Hapkido. A questionnaire survey method was conducted with 300 middle and high school students aged 14–19 years having Hapkido training of three months to two years in Incheon and Bucheon during March–April 2019. Frequency, factor, reliability, correlation, and standard multiple regression analyses were conducted on the surveyed data. The conclusions are as follows. First, considering the impact of service quality on exercise continuation intention, service quality positively affects reliability, personification, and perceptual openness; in terms of possibility, it positively affects typicality, personification, and perceptual openness; and in terms of reinforcement, it positively affects reliability and perceptual openness. Second, examining the impact of service quality on recommendation intention positively affects reliability, personification, and perceptual openness. Third, exercise continuation intention positively affects recommendation intention.

In recent, Chae found that, at weak gravitational acceleration g_N≲10⁻⁹ms⁻², the observed orbit of the wide binary stars is not accordant with current theory of binary star. Here, we present, this finding should be an observational evidence for that Newtonian theory of orbit perturbation is still valid in galactic scale.

Suppose G is a graph with vertex-orbits O1,1 O2, . . . ,Ot, and jOi j denotes the cardinallity of Oi. Then OG (x) = åt 2 i=1 xjOi j is called as orbit polynomial. It is well-known that this polynomial 3 has a unique positive zero d in the interval [0, 1]. The aim of this paper is to study the specific 4 properties of this polynomial and then we determine the location of this root for several classes of 5 complex networks to compare with other graphical measures. Besides, we compare the unique 6 positive zero measure with several well-known centrality graph measures.

The usual equation for both motions of a single planet around the sun and electrons in the deterministic Rutherford-Bohr atomic model is conservative with a singular potential at the origin. When a dissipation is added, new phenomena appear which were investigated thoroughly by R. Ortega and his co-authors between 2014 and 2017, in particular all solutions are bounded and tend to $0$ for $t$ large, some of them with asymptotically spiraling exponentially fast convergence to the center. We provide explicit estimates for the bounds in the general case that we refine under specific restrictions on the initial state, and we give a formal calculation which could be used to determine practically some special asymptotically spiraling orbits. Besides, a related model with exponentially damped central charge or mass gives some explicit exponentially decaying solutions which might help future investigations. An atomic contraction hypothesis related to the asymptotic dying off of solutions proven for the dissipative model might give a solution to some intriguing phenomena observed in paleontology, familiar electrical devices and high scale cosmology

The usual equation for both motions of a single planet around the sun and electrons in the deterministic Rutherford-Bohr atomic model is conservative with a singular potential at the origin. When a dissipation is added, new phenomena appear. It is shown that whenever the momentum is not zero, the moving particle does not reach the center in finite time and its displacement does not blow-up either, even in the classical context where arbitrarily large velocities are allowed. Moreover we prove that all bounded solutions tend to $0$ for $t$ large, and some formal calculations suggest the existence of special orbits with an asymptotically spiraling exponentially fast convergence to the center.

Smart, reliable, and connected multi-modal mobility has been a long-standing goal of transit services. This paper focuses on the smart, seamless, and multi-modal mobility service in the context of “Mobility as a Service” (MaaS). Intelligent mobility is the smarter, greener, and more efficient movement of passengers around the world. Increasingly, mobility is approached as a service. This study first conducts an extensive literature review on mobility behavior and demand pattern of MaaS end-users. It then extends the mechanism of supply chain, MaaS, synergy (i.e., vertical cooperation synergy, horizontal competition synergy), and coopetition to develop the multi-tier closed-loop intelligent mobility service supply chain network. This paper explains the intelligent mobility service supply chain network from following perspectives: (i) mobility service taxonomy of MaaS; (ii) aims of intelligent mobility service supply chain network; (iii) urban rail transit (URT)-centered alternatives for integrated multimodal journey planning, i.e. access + URT + egress, and both access and egress can be served by Mobility-On-Demand (MOD) transport; (iv) node member imperatives. From a synthesis of insights from the ‘during’ journey, this study puts forward the synergetic design of intelligent mobility service supply chain network, including: (i) multi-tier closed-loop structure; (ii) key nodes identification for the physical multimodal transport network in the supply chain; (iii) hybrid synergy mechanisms among the partners, i.e., synergy principle, temporal splitting approach for coopetition synergy; (iv) index systems and evaluation methods for synergy measurement. This study also contributes to the integrated multimodal journey planning. In concluding, the paper highlights the important implications of the proposed intelligent mobility service supply chain network for MaaS bundle design and adverse effects reduction, resulting from 1 + 1 > 2 synergy effects.

The Direction-of-Arrival (DoA) estimation methods are highly versatile and find extensive applications in satellite communication. The DoA methods are employed across a range of orbits, from Low Earth Orbits (LEO) to Geostationary Earth Orbits (GEO). They serve multiple applications, including altitude determination, geolocation and estimation accuracy, target localization, and relative and collaborative positioning. This paper presents a novel approach for modeling the DoA angle using a closed-form expression, incorporating the boresight angle and satellite and Earth station position data. The method uses the geographic coordinate system in the satellite communication system, precisely the latitude and longitude of the Earth station and altitude parameters of the satellite stations, to calculate the Earth station’s elevation angle and accurately model the DoA angle. Furthermore, this paper performs a comprehensive comparative analysis of various DoA methods to gain deeper insights into the performance of DoA estimation in multi-antenna systems operating under spatially correlated channels. Accordingly, this paper evaluates DoA estimation performance using root-mean-square-error (RMSE) statistics for uplink and downlink conditions through extensive Monte Carlo simulations. The simulation’s effectiveness is validated against the Cramer-Rao Bound (CRB) performance metric for the Additive white Gaussian noise (AWGN) case. (i.e., thermal noise). The simulation results demonstrate improved RMSE performance in satellite systems by incorporating spatial correlation into the system model.

Orbital fractures are a common finding in facial trauma and serious complications may arise when orbital reconstruction is not done properly. The virtual planning can be used to manufacture patient-specific titanium orbital implants (PSI) through the process of selective laser melting. This method is currently considered the most accurate technique for orbital reconstruction. Even with the most accurate tehniques of bone reconstruction, there are still situations where enophthalmos is present after reconstruction which may be produced by intraorbital soft tissue atrophy. The aim of this paper was to evaluate the orbital soft tissue after postraumatic reconstruction of the orbital walls fractures. 10 patients diagnosed with unilateral orbital fractures were included in this study. A CT scan of the head region with thin slices (0.6mm) and soft and bone tissue windows was done. After data processing, the STL files were exported and the intraorbital fat tissue volume and the muscular tissue volume were masured. The volumes of affected orbit tissues were compared with the volumes of the healthy orbit tissues for each patient. Our findings conclude that a higher or a lower grade of fat and muscular tissue loss is present in all cases of reconstructed orbital fractures.

Hip replacement has significantly improved the quality of life of patients with symptomatic hip osteoarthritis. Metal-on-metal (MoM) bearings have been used with conventional total hip re-placement (THR) for several decades with promising results from early applications. Wear and corrosion of these implants may lead to a release of metal products into surrounding tissue and body fluids. From the 1980s onwards, the search for increasingly better coupling materials with low levels of wear led to the rise of hard-on-hard couplings such as ceramic-on-ceramic (CoC). The latter is currently the coupling with the longest known duration and with a wear rate close to zero. MoM coupling has been for a long time the most significative alternative, but systemic and local complications linked to the release of chromium and cobalt ions, determine the withdrawn from the market. One other alternative proposed over the time has been Ceramic-on-Metal (CoM) bearing. Preliminary results have been described as favourable, but due to the failures of metal on metal it has been withdrawn from the market, without causing significant clinical complications. In this narrative review, we analysed risks and benefits associated with the implantation of hybrid hard-on-hard bearings, such as CoM.

The purpose of this paper is to investigate the effect of a varying moment on the rotation angle of a large tethered satellite that is orbiting a planet. Two different types of orbits were investigated: a simple circular orbit and an elliptical orbit. Cases with zero and non-zero initial angular rotation velocity were investigated as well. This investigation will assist satellite docking missions. The large rigid tethered satellite is a futuristic concept, and this investigation is meant to assist possible docking missions to the satellite. To simplify the problem, the rotation is constrained to the orbital plane.

Alzheimer’s disease (AD) is a significant health concern worldwide with enormous social and economic impact globally. The gradual deterioration of cognitive functions and irreversible neuronal losses are primary features of the disease. Even after decades of research, most therapeutic options are merely symptomatic, and drugs in clinical practice present numerous side effects. Lack of effective diagnostic techniques prevents the early prognosis of disease, resulting in a gradual deterioration in the quality of life. Furthermore, the mechanism of cognitive impairment and AD pathophysiology is poorly understood. Microfluidics exploits different microscale properties of fluids to mimic environments on microfluidic chip-like devices. These miniature multichambered devices can be used to grow cells and 3D tissues in vitro, analyze cell-to-cell communication, decipher the roles of neural cells like microglia, and gain insights into AD pathophysiology. This review focuses on the applications and impact of microfluidics on AD research. We discuss the technical challenges and possible solutions provided by this new cutting-edge technique to understand disease-associated pathways and mechanisms.

There are gravitational field and baryonic matter (star, planet, gases etc.) in our world; gravitational field is much more fundamental for that the relativistic mass of the gravitational field of a neutron star is almost 10²¹ times the mass of the neutron star. And, it is astonishing that the relativistic mass density of the gravitational field on the surface of a neutron star can be larger than the mass density of the neutron star. It is well known that, in the weak gravitational field a light line appears a straight line while in the strong field it is a curved line. It is stressed that the result measured in the strong field is more fundamental for that in a galaxy the measurable object is generally with strong field. It results in that the way that the result measured on the Earth with weak field is used as the universal standard need be revised as gravity is studied in the scale of a galaxy. It seems that a new theory of gravity need be developed for the new observations.

In order to monitor the diversity of terrestrial biomes, the Earth Exploration Satellite Services demand a high data rate for downlink transmissions while sharing their frequency spectrum with, and suffering interferences from, cellular Base Stations. Both highlight the dilemmas of spectral efficiency (bps/Hz) and spectral coexistence. Our research aims to mitigate interference on low orbit satellite downlinks using Cognitive Radio (CR) and Adaptive MODulation and CODing (MODCOD) techniques. To fulfill this: 1) we present CR approaches to enhance spectrum exploitation. Next, 2) we detail Adaptive MODCOD (ACM) technique to increase RF power and spectral efficiencies. Then, 3) we suggest the solution by combining 1) and 2). Afterwards, 4) we analyze it by monitoring the signal to interference plus noise ratio and the CR/MODCOD strategy. Finally, 5) we provide case studies to demonstrate the strategy’s effectiveness through the practical operation of satellite services, and 6) we conduct a bench test of the communication system.

The electron of magnetic spin −1/2 is a Dirac fermion of a complex four-component spinor field. Though it is effectively addressed by relativistic quantum field theory, an intuitive form of the fermion still remains lacking. In this novel undertaking, the fermion is examined within the boundary posed by a recently proposed MP model of a hydrogen atom into 4D space-time. Such unorthodox process conceptually transforms the electron to the four-component spinor of non-abelian in both Euclidean and Minkowski space-times. Supplemented by several postulates, the relativistic and non-relativistic applications of the model are explored from an alternative perspective. The outcomes have important implications towards defining the spin-orbit coupling of particles from external light interactions. These findings, if considered could consolidate properly the fundamentals of the quantum state of matter from an alternative perspective using quantum field theory application and they warrant further investigations.

After proposing the Principle of Minimum Gravitational Potential, in a pursuit to find the explanation behind the correction to Newton's gravitational potential that accounts for Mercury's orbit, by finding all the higher-order corrections it is shown that the consequences of the existence of speed of light for gravity are not yet fully explored.

Background: Exclusively breastfeeding your newborn while in the hospital is imperative for suc-cessful breastfeeding at home. This study will investigate if having a nurse on-site during rooming-in can enhance the proportion of exclusive breastfeeding. Methods: We carried out a prospective cohort study to assess exclusive breastfeeding in the first three months of life among two Neona-tology Units in Southern Italy with different hospital settings. The Ente Ecclesiastico Miulli of Ac-quaviva delle Fonti had on-site nurses available 24/7 (on-site group), while the Policlinico of Bari had nurses available on call 24/7 from the Neonatology Unit (on-call group). Results: Between January 3rd and March 31st, 2018, a total of 564 sets of mothers and babies were admitted - 299 on-site and 265 on-call. The exclusive breastfeeding rate for the entire group was 76.4% at 90 days, demonstrating the positive impact of rooming-in and nursing, regardless of the setting. Infants delivered via ce-sarean section in the on-site group demonstrated higher rates of exclusive breastfeeding at both 30 and 90 days of life. Conclusions: Our research indicates that having a nurse available at all times is crucial for promptly identifying any problems with breastfeeding. We highly suggest having an on-site nurse present during rooming-in for mothers who have had a caesarean delivery. This nurse should continuously promote exclusive breastfeeding until the baby is three months old.

Microfluidic lab-on-chip devices are widely being developed for chemical and biological studies. One of the most commonly used types of these chips is perfusion microwells for culturing multicellular spheroids. The main challenge in such systems is the formation of substantial necrotic and hypoxic zones within the cultured spheroids. Herein, we propose a novel acoustofluidic integrated platform to tackle this bottleneck problem. We show that such an approach enhances cell viability and shrinks necrotic and hypoxic zones in these spheroid-on-a-chip platforms without the need to increase the flow rate, leading to a significant reduction in costly reagents' consumption. Proof-of-concept, designing procedures, and finite element numerical simulation are discussed in details. Also, the effects of acoustic and hydrodynamic parameters on the cultured cells are investigated. The results show that by increasing acoustic boundary displacement amplitude (d0), the spheroid’s proliferating zone enlarges greatly. Moreover, it is shown that by implementing d0=0.5 nm, the required flow rate to maintain the necrotic zone below 13% will be decreased 12 times compared to non-acoustic chips.

Pin-on-plate and pin-on-disk wear tests are typically used for assessing the wear behavior of a given material coupling. Such a behavior is frequently described by a wear coefficient k, which is estimated, according to the Archard’s law, as the ratio between the measured wear volume V and the product of the applied normal force F and the sliding distance s, i.e. k=V/(F s). This study demonstrates that such a relationship is correct for pin-on-plate but not for pin-on-disk, particularly for flat-ended pins. Both analytical and finite element models of the two tests were developed, considering three different distances pin-disk axis. As results, wear volumes, pressure and wear depth maps were examined and compared for the same sliding distance. Though this study is focused only on the initial transient part of the wear tests, some interesting aspects arose: i) rotational effect in pin-on-disk tests affects k estimation, especially when the pin is near to the disk axis; ii) a simple analytical function is defined to correct the wear volume estimation for pin-on-disk tests; iii) due to the different sliding distances of contact points in pin-on-disk tests, pressure redistribution occurs with higher values on the inner side (closer to disk axis); the opposite trend is observed in wear depth maps. From a computational point of view, the pin-on-disk problem, only apparently simple, required very small time increments to correctly describe the circular trajectories of points, with high computational costs. Numerical strategies are currently under investigation to extend the study to the steady state phase of both tests.

The most commonly used real-time augmentation services in China are International GNSS Service (IGS) real-time service, PPP-B2b service, and BeiDou Satellite-Based Augmentation System (BDSBAS) dual-frequency augmentation service. However, the research on the performance evaluation, comparison and application scope of these three products is still unknown and unrevealed. This article introduces methods for obtaining real-time augmentation information and real-time orbit and clock offset recovery. Based on real-time orbit and clock offset accuracy, positioning accuracy, and positioning availability, it systematically evaluates the performance of CNES, PPP-B2b, and BDSBAS augmentation information. The results indicate that the radial accuracy of CNES and PPP-B2b real-time orbit products is consistent, and the Root Mean Square (RMS) is better than 5 cm. CNES can achieve centimeter-level accuracy in both along-track and cross-track components, surpassing the decimeter-level accuracy of PPP-B2b. Both services demonstrate consistent accuracy in real-time clock offset, with PPP-B2b showing similar standard deviations (STD) of 0.16 ns for different satellites. However, for CNES, the STD of real-time clock offset varies for GPS, BDS-3 MEO, and BDS-3 IGSO satellites, with values of 0.10 ns, 0.19 ns, and 0.60 ns, respectively. The accuracy and availability of the two PPP services exhibit the same levels, with centimeter-level accuracy achieved after convergence and positioning availability exceeding 99%. Therefore, the difference between the two services in application areas depends on the acquisition of augmentation information. However, BDSBAS, which concentrates on code observations, demonstrates lower accuracy in real-time orbit and clock offset, positioning accuracy, and positioning availability compared to the other two services. Its primary application is in the aviation and maritime domains, where there is a greater need for service integrity, continuity, and reliability.

Distant Retrograde Orbits in the Earth-Moon system are gaining in popularity as stable `parking' orbits for various conceptual missions. To investigate the stability of potential Distant Retrograde Orbits, simulations were executed, with propagation running over a thirty-year period. Initial conditions for the vehicle state were limited such that the position and velocity vectors were in the Earth-Moon orbital plane, with the velocity oriented such that it would produce retrograde motion about Moon. The resulting trajectories were investigated for stability against the eccentric relative orbits of Earth and Moon in an environment that also included gravitational perturbations from Sun, Jupiter, and Venus, and the effects of radiation pressure. The results appear to indicate that stability is enhanced for certain resonant states within the Earth-Moon system.

Digital microfluidics (DMF) holds great potential for the alleviation of laboratory procedures in assisted reproductive technologies (ARTs). Electrowetting on dielectric (EWOD) provides dynamic culture conditions in vitro that may better mimic the natural embryo microenvironment. Thus far, EWOD microdevices have been proposed for in vitro gamete and embryo handling in mice and for analyzing the human embryo secretome. This article presents the development of the first microfluidic chip utilizing EWOD technology designed for the manipulation of bovine embryos in vitro. The prototype sustains the cell cycles of embryos manipulated individually on the chips during in vitro culture (IVC). Challenges related to the chip fabrication as well as to its application during bovine embryo IVC in accordance with the adapted on-chip protocol are thoroughly discussed, and future directions for DMF in ARTs are indicated.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

The application of space robotic manipulators and heightened autonomy for ios represents a paramount pursuit for leading space agencies, given the substantial threat posed by space debris to operational satellites and forthcoming space endeavors. This work presents a guidance algorithm based on drl to solve for the space manipulator path-planning during the motion synchronization phase with the mission target. The goal is the trajectory generation and control of a spacecraft equipped with a 7-dof robotic manipulator, such that its end effector remains stationary with respect to the target point of capture. The ppo drl algorithm is used to optimize the manipulator’s guidance law, and the autonomous agent generates the desired joints rates of the robotic arm, which are then integrated and passed to a model-based feedback linearization controller. The agent is first trained to optimize its guidance policy and then tested extensively to validate the results against a simulated environment representing the motion synchronization scenario of an ios mission.

Aiming at the development of the application of massive and heterogeneous LEO constellations, the influence of typical perturbation forces on the orbit prediction of LEO satellites at different altitudes is analyzed. Firstly, the main perturbation force model of LEO satellites is introduced. Then experiments for analyzing the influence of orbit prediction on LEO satellites at different altitudes are designed. Finally, the influence of typical perturbation forces on the orbit prediction under different prediction durations by numerical analysis is assessed systematically, and the orbit prediction of LEO satellites with different non-spherical gravitational field orders, ocean tide orders and atmospheric density models were compared and calculated. The research results show that different orders of non-spherical gravitational fields should be considered when the altitude of satellites is different, the reasonable gravitational field orders for LEO satellites at 500km, 1000km, 1500km and 2000km under 1-hour forecast time are 140x140, 80x80, 60x60 and 40x40 orders, the reasonable orders of ocean tide perturbation for 1500km and 2000km satellites are 20x20 orders. Under the 24-hour forecast time, atmospheric resistance has a great influence on the precision of LEO satellites at orbit altitude below 1,000km. The forecast deviation of the LEO satellites orbit at 500km reaches 8751.576m. The difference of orbit precision between different atmospheric density models is in the meter level. The orbit deviation by the Standard Atmosphere 1976 and NRLMSISE 2000 atmospheric models respectively reaches 25.494m. Relevant conclusions provide support for the optimization and selection of dynamical models in high precision orbit determination and fast orbit prediction of LEO satellites.

Using the orbit decomposition, a new enumerative polynomial P(x) is introduced for abstract (simplicial) complexes of a given type, e.g., trees with a fixed number of vertices or triangulations of the torus with a fixed graph. The polynomial has the following three useful properties. (I) The value P(1) is equal to the total number of unlabeled complexes (of a given type). (II) The value of the derivative P'(1) is equal to the total number of nontrivial automorphisms when counted across all unlabeled complexes. (III) The integral of P(x) from 0 to 1 is equal to the total number of vertex-labeled complexes, divided by the order of the acting group. The enumerative polynomial P(x) is demonstrated for trees and then is applied to the triangulations of the torus with the vertex-labeled complete four-partite graph G = K_{2,2,2,2}, in which specific case P(x) = x^{31}. The graph G embeds in the torus as a triangulation, T(G). The automorphism group of G naturally acts on the set of triangulations of the torus with the vertex-labeled graph G. For the first time, by a combination of algebraic and symmetry techniques, all vertex-labeled triangulations of the torus (twelve in number) with the graph G are classified intelligently without using computing technology, in a uniform and systematic way. It is helpful to notice that the graph G can be converted to the Cayley graph of the quaternion group Q_8 with the three imaginary quaternions i, j, k as generators.

Orbit and clock products are used in real-time GNSS precise point positioning without knowing their quality. This study develops a new approach to detect orbit and clock errors through comparing geometry-free and geometry-based wide-lane ambiguities in PPP model. The reparameterization and estimation procedures of the geometry-free and geometry-based ambiguities are described in detail. The effects of orbit and clock errors on ambiguities are given in analytical expressions. The numerical similarity and differences of geometry-free and geometry-based wide-lane ambiguities are analyzed using different orbit and clock products. Furthermore, two types of typical errors in orbit and clock are simulated and their effects on wide-lane ambiguities are numerically produced and analyzed. The contribution discloses that the geometry-free and geometry-based wide-lane ambiguities are equivalent in terms of their formal errors. Although they are very close in terms of their estimates when the used orbit and clock for geometry-based ambiguities are precise enough, they are not the same, in particular, in the case that the used orbit and clock, as a combination, contain significant errors. It is discovered that the discrepancies of geometry-free and geometry-based wide-lane ambiguities are coincided with the actual time-variant errors in the used orbit and clock at the line-of-sight direction. This provides a quality index for real-time users to detect the errors in real-time orbit and clock products, which potentially improves the accuracy of positioning.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

Living organisms are active open systems far from thermodynamic equilibrium. The ability to behave actively corresponds to dynamical metastability: minor but supercritical internal or external effects may trigger major substantial actions such as gross mechanical motion, dissipating internally accumulated energy reserves. Gaining selective advantage from beneficial use of activity requires a consistent combination of sensual perception, memorised experience, statistical or causal prediction models, and resulting favourable decisions on actions. This information processing chain originated from mere physical interaction processes prior to life, here denoted as structural information exchange. From there, the self-organised transition to symbolic information processing marks the beginning of life, evolving by novel purposivity of trial-and-error feedback and accumulation of symbolic information. The emergence of symbols and prediction models can be described as a ritualisation transition, a symmetry-breaking kinetic phase transition of the 2^nd kind previously known from behavioural biology. The related new symmetry is the neutrally stable arbitrariness, conventionality or code invariance of symbols with respect to their meaning. The meaning of such symbols is given by the structural effect they ultimately unleash, directly or indirectly, by deciding on which actions to take. The early genetic code represents the first symbols. The genetically inherited symbolic information is the first prediction model for activities sufficient for survival under the condition of environmental continuity, sometimes understood as a “final causality” property of the model.

Satellite communication is expected to play a vital role in realizing Internet of Remote Things (IoRT) applications. This article considers an intelligent reflecting surface (IRS)-assisted downlink low Earth orbit (LEO) satellite communication network, where IRS provides additional reflective links to enhance the intended signal power. We aim to maximize the sum-rate of all the terrestrial users by jointly optimizing the satellite’s precoding matrix and IRS’s phase shifts. However, it is difficult to directly acquire the instantaneous channel state information (CSI) and optimal phase shifts of IRS due to the high mobility of LEO and the passive nature of reflective elements. Moreover, most conventional solution algorithms suffer from high computational complexity and are not applicable to these dynamic scenarios. A robust beamforming design based on graph attention networks (RBF-GAT) is proposed to establish a direct mapping from the received pilots and dynamic network topology to the satellite and IRS’s beamforming, which is trained offline using the unsupervised learning approach. The simulation results corroborate that the proposed RBF-GAT can achieve approximate performance compared to the upper bound with low complexity.

In this paper we investigate analytic automorphisms of complex topological vector spaces and their applications to linear and nonlinear transitive operators. We constructed some examples of polynomial automorphisms which show that a natural analogue of the Jacobian Conjecture for infinite dimensional spaces is not true. Also, we prove that any separable Fréchet space supports a transitive analytic operator which is not a polynomial. We found some connections of analytic automorphisms and algebraic bases of symmetric polynomials and applications to hypercyclisity of composition operators.

In this paper, a prototype of an automatic lab on PCB for agarose preparation and electrophoresis is developed. The dimensions of the device are 38×34 mm2 and includes a conductivity sensor for detecting the TAE buffer (Tris-Acetate-EDTA buffer), a microheater for mixing, a NTC thermistor for controlling the temperature, a LDR sensor for measuring the transparency of the mixture, and two electrodes for performing the electrophoresis. The agarose preparation functions are governed by a microcontroller. The device requires a PMMA structure to define the wells of the agarose gel, and to release the electrodes from the agarose. The maximum voltage and current that the system requires are 40 V to perform the electrophoresis, and 1 A for activating the microheater. The chosen temperature for mixing is 80ºC, with a mixing time of 10 min. In addition, the curing time is about 30 min. This device is intended to be integrated as a part of a larger lab on PCB system for DNA amplification and detection. However, it can be used to migrate DNA amplified in conventional thermocyclers. Moreover, the device can be modified for preparing larger agarose gels and performing electrophoresis in an automatic manner.

Organ-on-Chip is a game-changing technology born from the convergence of tissue engineering and microfluidic technology. Organ-on-Chip devices (OoCs) are expected to offer effective solutions to persisting problems in drug development and personalized disease treatments. This opinion paper surveys the current landscape in research, development, application and market opportunities for OoCs to help establishing a global and multi-stakeholder OoC ecosystem. Based on a bibliometric study, a market analysis, expert interviews, and panel discussions held at the ORCHID Vision Workshop (Stuttgart, 23 May 2018), we outline presently unmet needs, key challenges, barriers and perspectives of the field, and finally propose recommendations towards the definition of a comprehensive roadmap that could render OoCs realistic models of human (patho)physiology in the near future.

This research paper contributes to the literature of deterrence theory in general, and in particular with respect to white-collar crime, offering valuable inside by using a unique data set of fraud and violation of trust incidents for Paraguay. Descriptive evidence show a clear and continuous misallocation of funds and human capital, and therefore providing less efficient services for the public. Regression analysis suggests that clearance rate exerts a highly significant effect in deterring fraud but results are not clear for violation of trust incidents. Despite the limitations of available data, results confirm deterrence theory in Paraguay. However, to more than two-thirds of victims, not even the attempt was made to seek justice. As a side-result, it seems that a soft on crime strategy, induced from the former German penal code, has led to an increasing share of pre-trial diversion and therefore enhancing white-collar crimes like fraud and violation of trust due to impunity.

Biometric based access control system acts as a weapon against the challenges for reliable authentication mechanism. Although there are many advantages of biometric system, still it is vulnerable to attacks, which decline its security. This leads to propose a new approach to address these open issues and challenges for biometric data security. Smart card have been already used in past with various degree of success to store biometric credentials. Match-on-card biometric framework locks the biometric data inside the microcontroller of the smart card, which leads to minimal risks if card is lost or stolen. It is fast and accurate, balancing security and convenience by never exchanging user data outside the system of smart card and performs fingerprint enrollment as well as matching within a tamperproof environment of smart card.

The concept of geostationary VHTS (Very High Throughput Satellites) is based on multibeam coverage with intensive frequency and polarization reuse in addition to the use of larger bandwidths in the feeder links, in order to provide high capacity satellite links at a reduced cost per Gbps in orbit. The dimensioning and design of satellite networks based on VHTS imposes the analysis of multiple trade-offs to achieve an optimal solution in terms of cost, capacity and figure of merit of the user terminal. In this paper, we propose a new method for sizing VHTS satellite networks based on an analytical expression of the forward link CINR (Carrier-to-Interference-plus-Noise Ratio) that is used to evaluate the trade-off of different combinations of system parameters. The proposed method considers both technical and commercial requirements as inputs including the constraints to achieve the optimum solution in terms of the user G/T, the number of beams and the system cost. The cost model includes both satellite and ground segments. Exemplary results are presented with feeder links using Q/V bands, DVB-S2X and transmission methods based on CCM and VCM (Constant and Variable Coding and Modulation, respectively) in two scenarios with different service areas.

In this paper, an attempt has been made to analyze the effect of spool port/ groove geometry on the pressure drop and chamber pressures which effect the performance parameters of the flow distributor valve. The work mainly involves formulation of detailed mathematical model of the valve and compare them on the same platform. For mathematical modelling, Matlab has been used. The size of the orifices is considered same throughout the model for better comparison. Initially the construction and functioning of flow distributor valve along with working principles of hydrostatic motor (Rotary Piston) is shown. Next shown the analytical analysis of area change and pressure drops due to different geometry of the spool valve ports. After that the computational fluid dynamics (CFD) analysis has been shown. A complete mathematical model to describe such flow distributor valve is developed after having a comprehensive knowledge of orifice characteristics, flow interactions based on valve geometry. Equations of flow through different orifices (fixed and variable area) of the valve have been developed based on the relationships obtained earlier.

In this paper, the problem of autonomous optimal absolute orbit keeping for a satellite mission in Low Earth Orbit using electric propulsion is considered. The main peculiarity of the approach is to support small satellite missions in which the platform is equipped with a single thruster nozzle which provides acceleration on a single direction at a time. This constraint implies that an attitude maneuver is necessary before or during each thrusting arc to direct the nozzle into the desired direction. In this context, an attitude guidance algorithm specific for the orbit maneuver has been developed. A Model Predictive Control scheme is proposed, where the attitude kinematics are coupled with the orbital dynamics in order to obtain the optimal guidance profiles in terms of satellite state, reference attitude, and thrust magnitude. The proposed control scheme is developed exploiting Formation Flying techniques where the reference orbit is that of a virtual spacecraft that the main satellite is required to rendezvous with. In addition to the controller design, the closed loop configuration is presented supported by numerical simulations. The efficacy of the proposed autonomous orbit keeping approach is shown in several application scenarios.

We summarize the results on electron transport in hybrid superconducting S/B/S' mesa-structure consisted of the oxide epitaxial S/B heterostructures, where S is the cuprate YBa2Cu3O 7-x superconductor, B – an interlayer with the spin dependent characteristics, and S’ is the Nb top superconductor. Josephson effect was observed manifested in appearance of oscillating Shapiro steps amplitudes with microwave signal power due to synchronization of junction self-generation of electromagnetic radiation and the external microwave probe signal. Triplet component of superconducting correlations emerged when the interlayer comprised two magnetic materials SrRuO3 and La0.7Sr0.3MnO3 with non-collinear magnetizations as well in the case of antiferromagnetic insulator Sr2IrO4 characterized by strong spin-orbit interaction. Thickness of the interlayer in the both cases considerably exceeded the coherence length of the magnetic spin active interlayer hinting on appearance of long-range proximity effect and spin-triplet superconducting current. Magnetic field dependences measured at dc, and the existence of the second harmonic in superconducting current–phase relation revealed by measurements at microwave frequencies will be discussed.

Exact sequential state estimation of orbiting objects in space can be found by predicting the state using Fokker Planck Kolmogorov Equation (FPKE) and measurement correction using Bayes’ conditional/posterior Probability Density Function (PDF). Posterior PDF can be expressed as Gaussian density expanded in terms of Hermite polynomials named as Gram Charlier Series (GCS). This research is an extension of an earlier work on second order linearized solution to nonlinear Bayesian filtering using Taylor series and third order GCS expansion of posterior PDF. In this new extension, Bayes’ posterior PDF is approximated by a mixture of GCS functions for which the parameters are propagated using linear propagation theory. The update of weights of different components of GCS mixture model uses the FPKE error as feedback to adapt for the amplitude of different GCS components while solving a quadratic programming problem earlier used for Gaussian Mixture Model (GMM) PDF. Proposed filtering method is applied on tracking of space debris. The simulation results for the filter shows performance is moderately better than single GCS filter, Extended Kalman Filter (EKF) and Gaussian Sum Filter (GSF) under space debris’ highly uncertain initial conditions and sparse measurement availability.

For Interferometry Synthetic Aperture Radar (InSAR), the normal baseline is one of the main factors that affect the accuracy of the ground elevation. For Gaofen-3 (GF-3) InSAR processing, the poor accuracy of the real-time orbit determination resulting in a large baseline error, leads to the modulation error in azimuth and the slope error in range for timely Digital Elevation Model (DEM) generation. In order to address this problem, a baseline estimation method based on external DEM is proposed in this paper. Firstly, according to the characteristic of the real-time orbit of GF-3 images, orbit fitting is executed to remove the non-linear error factor. Secondly, the height errors are obtained in slant-range plane between Shuttle Radar Topography Mission (SRTM) DEM and the GF-3 generated DEM after orbit fitting. At the same time, the height errors are used to estimate the baseline error which has a linear variation. In this way, the orbit error can be calibrated by the estimated baseline error. Finally, DEM generation is performed by using the modified baseline and orbit. This procedure is implemented iteratively to achieve a higher accuracy DEM. Based on the results of GF-3 interferometric SAR data for Hebei, the effectiveness of the proposed algorithm is verified and the accuracy of GF-3 real-time DEM products can be improved extensively.

Worldwide, among older adults, infection is the leading mortality cause; chronic nutritional deficits confer significant mortality risk and increase healthcare costs. The association of the Global Leadership Initiative on Malnutrition (GLIM)-defined malnutrition with infection-related mortality, especially with renal dysfunction in older patients, remains unevaluated. In older patients hospitalized with infection, stratified by renal function, we investigated the association of malnutrition severity with mortality. This single-center, retrospective cohort study of 1220 participants (age ≥65 years) admitted to Aichi Medical University from 2019 to 2020 used a multivariate Cox proportional hazards model to determine the association of GLIM-defined nutritional status (no, moderate, or severe malnutrition) with all-cause mortality. Compared to no malnutrition, moderate and severe malnutrition conferred significantly higher mortality (adjusted hazard ratio [confidence interval ]: 1.00 [reference], 1.76 [1.28-2.42], and 2.44 [1.78-3.33], respectively), with the highest all-cause mortality in malnutrition with a low estimated glomerular filtration rate (eGFR <30 mL/min/1.73m2; 7.35 [4.57-11.8]) compared to no malnutrition and normal eGFR (≥60 mL/min/1.73m2). GLIM-defined malnutrition confers higher all-cause mortality risk in older adults with infection, especially those with renal dysfunction. This information enables the identification of high-risk older patients with infection and targeted clinical management of those with malnutrition, renal dysfunction, and infection.

Oncological changes in the prostate are a common cause of death among elderly men. Malignant cells are difficult to identify at early stages, which are asymptomatic. The patient often seeks medical assistance when the disease has already progressed, and the treatment is less effective. Early diagnosis of prostate cancer (PC) is thus one of the priority tasks of modern urology and healthcare in general. The aim of this study is the detection of microRNAs (miRNAs), which are known to be associated with PC. The detection of the target miRNAs in human plasma samples has been performed with a nanoribbon biosensor system, which was based on "silicon-on-insulator" structures (SOI-NR biosensor). In order to provide biospecific detection of the target miRNAs, the surface of individual nanoribbons has been modified with DNA oligonucleotide probes (oDNA probes), whose nucleotide sequences were complementary to those of the target miRNAs. The high detection sensitivity has been demonstrated with the use of model oDNAs, which are complementary to nanoribbon-immobilized oDNA probes, in buffer solutions. The sensitivity threshold was 1.1 × 10^-17 M. The successful detection of target miRNAs, isolated from real plasma samples of PC patients, has also been demonstrated. We believe that the development of highly sensitive nanotechnology-based biosensors for PC markers is a step towards personalized medicine.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

This paper aims to describe the geometrical structure and explicit expressions of family of finitely parametrized probability densities over smooth manifold $M$. The geometry of family of probability densities on $M$ are inherited from probability densities on Euclidean spaces $\left\{U_\alpha \right\}$ via bundle morphisms, induced by an orientation-preserving diffeomorphisms $\rho_\alpha:U_\alpha \rightarrow M$. Current literature inherits densities on $M$ from tangent spaces via Riemannian exponential map $\exp: T_x M \rightarrow M$; densities on $M$ are defined locally on region where the exponential map is a diffeomorphism. We generalize this approach with an arbitrary orientation-preserving bundle morphism; we show that the dualistic geometry of family of densities on $U_\alpha$ can be inherited to family of densities on $M$. Furthermore, we provide explicit expressions for parametrized probability densities on $\rho_\alpha(U_\alpha) \subset M$. Finally, using the component densities on $\rho_\alpha(U_\alpha)$, we construct parametrized mixture densities on totally bounded subsets of $M$. We provide a description of inherited mixture product dualistic geometry of the family of mixture densities.

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

The gut plays a key role in drug absorption and metabolism of orally ingested drugs. Additionally, characterization of intestinal disease processes are increasingly gaining more attention as gut health is an important contributor to our overall health. The most recent innovation to study intestinal processes in vitro is the development of gut-on-a-chip (GOC) systems. Compared to conventional in vitro models they offer more translational value, and many different GOC models have been presented over the past years. Here, we reflect on the almost unlimited choices in designing and selecting a GOC for preclinical drug (or food) development research. Four components that largely influence the GOC design are highlighted, namely 1) the biological research questions, 2) chip fabrication and materials, 3) tissue engineering, and 4) the environmental and biochemical cues to add or measure in the GOC. Examples are presented of GOC studies in the two major areas of preclinical intestinal research: 1) intestinal absorption and metabolism to study the oral bioavailability of compounds, and 2) treatment-orientated research for intestinal diseases. The last section of this review presents an outlook on the limitations to overcome in order to accelerate preclinical GOC research.

When the formation flying consists of satellites that are independent from each other and forms a virtual synthetic aperture telescope that replaces a single large telescope with all of its optical elements it is required mutual coordination between the satellites with high accuracy in order to achieve good optical observations. In this paper we consider the problem of developing a control system for a tetrahedral satellite formation flying representing a synthetic aperture telescope in the geostationary orbit for high resolution monitoring of fire in the forest area in infrared spectrum. Synthesizing the image with good quality requires to keep the configuration of formation with µm-class accuracy. Study of dynamics of passive uncontrolled motion of formation flying showed a significant deviation of the configuration from the required shape with a high frequency due to the action of gravitational forces. To keep the configuration in the required form with µm accuracy the analysis of efficiency of various controllers was carried out in the process of numerical simulation. The simulation results made it possible to highlight the features of using various approaches to the development of control system for the satellite formation flying representing a synthetic aperture telescope.

Based on measured astronomical position data of heavenly objects in the Solar System and other planetary systems, all bodies in space seem to move in some kind of elliptical motion with respect to each other. According to Kepler’s 1^st Law, “orbit of a planet with respect to the Sun is an ellipse, with the Sun at one of the two foci.” Orbit of the Moon with respect to Earth is also distinctly elliptical, but this ellipse has a varying eccentricity as the Moon comes closer to and goes farther away from the Earth in a harmonic style along a full cycle of this ellipse. In this paper, our research results are summarized, where it is first mathematically shown that the “distance between points around any two different circles in three dimensional space” is equivalent to the “distance of points around a vector ellipse to another fixed or moving point, as in two dimensional space”. What is done is equivalent to showing that bodies moving on two different circular orbits in space vector wise behave as if moving on an elliptical path with respect to each other, and virtually seeing each other as positioned at an instantaneously stationary point in space on their relative ecliptic plane, whether they are moving with the same angular velocity, or different but fixed angular velocities, or even with different and changing angular velocities with respect to their own centers of revolution. This mathematical revelation has the potential to lead to far reaching discoveries in physics, enabling more insight into forces of nature, with a formulation of a new fundamental model regarding the motions of bodies in the Universe, including the Sun, Planets, and Satellites in the Solar System and elsewhere, as well as at particle and subatomic level. Based on the demonstrated mathematical analysis, as they exhibit almost fixed elliptic orbits relative to one another over time, the assertion is made that the Sun, the Earth, and the Moon must each be revolving in their individual circular orbits of revolution in space. With this expectation, individual orbital parameters of the Sun, the Earth, and the Moon are calculated based on observed Earth to Sun and Earth to Moon distance data, also using analytical methods developed as part of this research to an approximation. This calculation and analysis process have revealed additional results aligned with observation, and this also supports our assertion that the Sun, the Earth, and the Moon must actually be revolving in individual circular orbits.

Separation and interpretation of rebellious Circulating Tumor Cells (CTCs) originating from the primary tumor or cancer tissue plays a significant role in diagnostics, cancer progression analyses, suitable medicine exploration, and treatment proficiency examination. Cancer metastasis occurs when CTCs spread throughout the body and invade healthy tissues, leading to new tumors in that area. Although a dramatic rate of deaths begins from spreading CTCs around the body, valuable measures have been made to control their development. However, the first step is separating these harmful cells from the bloodstream and investigating their features. Having examined the characteristics of CTCs as cancer’s main strength, researchers can introduce complementary treatments that can affect cancerous cells without damaging the healthy cells. Therefore, according to their unique characteristics, numerous techniques have been established for continuous and fast separation and sorting of CTCs. Nevertheless, few separators enjoy the efficient performance and appropriate accuracy and can be produced in mass numbers due to the available fabrication equipment. Microfabrication advancements enable separators to combine the advantages of active and passive methods in a small-scale platform for probing individual cells and separation purposes. Reduction in reagents, sample volume, analysis time, and less harmfulness to patients are some of the motivations that encourage researchers to employ microfluidic instruments for CTCs separation from other blood cells over the last two decades. However, microfabrication limitations mean effective separators, and the diagnostic option they provide, are not readily available. Addressing these limitations requires optimizing the design and fabrication of separators such that they are reduced in their size and fabrication cost, while also maintaining high-throughput separating capability. The emergence of the Lab-On-a-Chip (LOC) and then Lab-On-a-CD (LOCD) technologies, having more inherent benefits than conventional microfluidic devices, has created new opportunities and become increasingly widespread in recent years. Evidence suggests that employing single methodologies or integrating approaches without sufficient understanding of potential outcomes is unlikely to result in successful diagnostic results. This paper contributes an extensive review of several separation systems, including fundamental theories and experimental details, and describes detailed operating principles and device performance.

The Standard Model is not a complete description of reality; it omits the existence of dark matter, dark energy, and an explanation as to why no CP violation has been observed. However, some of these phenomena could be explained through a new force mediated by a new boson. If such a boson were massless it would result in a power law potential and if massive the interaction would be Yukawa-like. A previous experiment employing a micro-mechanical oscillator and a spherical test mass interactions was successful in placing the best limits on a mass-mass Yukawa-like interaction, but the data was never analyzed in the context of a power law. Here that data is analyzed considering a power law for powers n = 1-5 where n is the number of boson exchanges. The results show that the limits obtained through power law analysis of this data are not better than the currently accepted limits. A discussion of an experiment design capable of producing better limits on power law extensions to the Standard Model is presented, and suggests micro mechanical oscillators based experiment remains capable of improving the limits by at least one order of magnitude.

Spiking neural networks (SNNs) promise to perform tasks currently done by classical artificial neural networks (ANNs) faster, in smaller footprints and using less energy. Neuromorphic processors are set out to revolutionize computing at a large scale, but the move to edge-computing applications calls for finely-tuned custom implementations to keep pushing towards more efficient systems. To that end, we have examined the architectural design space for executing spiking neuron models on FPGA platforms, focusing on achieving ultra-low area and power consumption. This work presents an efficient clock-driven spiking neuron architecture used for the implementation of both fully-connected cores and 2D convolutional cores, which rely on deep pipelines for synaptic processing and distributed memory for weight and neuron states. With them, we have developed an accelerator for an SNN version of the LeNet-5 network trained on the MNIST dataset. At around 5.5 slices/neuron and only 348 mW, it is able to use 33% less area and 4 times as less power per neuron as current state-of-the-art implementations while keeping low simulation step times.

This paper sheds light on how crisis management affects post-disaster re-covery. Based on the study of the management of a major environmental disaster, hurricane IRMA, we consider how post-disaster recovery is impacted by crisis management strategies. The perspectives of local stakeholders from the islands of St Martin and St Barthélémy will be shared. We analyze how territories exposed to the same natural phenomena have different outcomes and consider some of the possible reasons. This study reveals underlying risk drivers, to address governance reorganization with a view to better managing socio-economic recovery.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

This paper introduces a novel 3D NoC router that combines buffered and bufferless routing with approximate priority comparison when deflecting flits. Our proposal is a modification of an asymmetrical router that is buffered in the z dimension ports and bufferless in the x and y dimension ports. Flits that request output ports in the x and y dimensions are granted or deflected based on approximate, instead of accurate, priority comparison. Experimental results show that the proposed router, besides effectively combining the advantages of both buffered and bufferless routers, it achieves additional performance and area gains due to the reduced logic required for approximate priority comparison in flit deflections. Experimental results using synthetic and realistic traffic show that the proposed router begins to saturate at a sifnificantly higher injection rate than a bufferless router, but at a slightly lower injection rate than when using accurate priority comparison. Furthermore, the proposed router achieves higher clock frequencies and reduced area compared to the simpler permutation network.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

Drug resistance has become an extremely serious problem worldwide. Antibiotic resistance genes (ARGs) entering the environment with wastewaters promote replenishment of the resistome of natural microbioms. Distribution of several clinically significant ARGs in wastewaters of Rostov-on-Don (Southern Russia), lower reaches of the Don River and natural waters of the neighboring region was investigated. Metagenomic DNA samples isolated from 250 ml of wastewaters or natural waters and 200 mg of surface sediments were used for the study. Identification of the ARGs was carried out with end-point detection PCR. Presence of NDM, OXA-48, CTX-M, VanA, VanB, ErmB, and TetM/TetO genes was detected in urban wastewaters. Samples of wastewater treatment plant (WWTP) sewage were enriched with ARGs in contrast to non-treated wastewaters from the sewage collector. NDM, VanA, ErmB, TetM/TetO genes were found only in wastewaters and were absent in samples of natural waters and surface sediments. Only OXA-48, VanB and CTXM genes were found in natural waters and surface sediments. The described ARGs are quite typical for urban and hospital wastewaters. The target ARGs were detected in the samples connected to the anthropogenous sources of pollution such as Rostov municipal WWTP or livestock enterprise effluents.

We report magnetic silver nanoshells (M AgNSs) that have both magnetic and SERS properties for SERS-based detection. The M AgNSs are composed of hundreds of Fe3O4 nanoparticles for rapid accumulation and bumpy silver shell for sensitive SERS detection by near-infrared laser excitation. The intensity of the SERS signal from the M AgNSs was strong enough to provide single particle-level detection. We obtained much stronger SERS signal intensity from the aggregated M AgNSs than from the non-aggregated AgNSs. 4-Fluorothiophenol was detected at concentrations as low as 1 nM, which corresponds to 0.16 ppb. The limit of detection for tetramethylthiuram disulfide was 10 μM, which corresponds to 3 ppm. The M AgNSs can be used to detect trace amounts of organic molecules using a portable Raman system.

Background: Artificial intelligence can help improve the quality of healthcare by analyzing vast amounts of data and providing more effective and personalized treatment plans. Researchers are working on developing AI-powered solutions that can help improve the outcomes of patients. Objective: To explore the potential of AI in improving healthcare outcomes and patient experience. Results: The study suggests that AI can improve healthcare efficiency and patient outcomes but cannot fully replace human healthcare professionals. AI can assist healthcare professionals in their work, leading to better resource utilization and improved patient care. However, there is still a need for human healthcare professionals to oversee AI systems and provide empathy and personalized care to patients. Conclusion: While there is immense potential for AI in healthcare, it is not yet feasible to replace human healthcare workers. Instead, it should be viewed as a tool that can help improve the efficiency and effectiveness of human healthcare.

Time-series analysis is a widely used technique across various fields and industries, as it helps in understanding, predicting, and forecasting the behavior of data points over time. These fields include but are not limited to finance, economics, healthcare, transportation, etc. In the case of this paper, we have focused on finance. Predicting future values of financial time series offers several benefits. Accurate forecasts can help investors make better decisions about their investments. To predict future values, deep learning algorithms are commonly used since it is an effective method with complex data. In this study, we conduct a study that investigates the use of different data pre-processing techniques on deep learning algorithms in predicting the time series values. To conduct this experimental study, we utilize an open source software, which using long short-term memory technique as the representative deep learning technique, published in github software code repository platform. With this study, we investigate the effects of autoencoder and discrete wavelet transform data pre-processing techniques in time-series prediction. We discuss the details of the experimental study and report our results. The results show that time series prediction (using backtesting methodology) without any data pre-processing leads to 12.6% for mean absolute percentage error. The results also show that, time series prediction with the data preprocessing techniques (Wavelet Transform and Stacked Autoencoder) lead to 3.4%

Isothermal Nucleic Acid Amplification based-Lateral Flow Testing (INAA-LFT) has emerged as a robust technique for on-site pathogen detection, providing a visible indication of pathogen nucleic acid amplification that rivals or even surpasses the sensitivity of real-time quantitative PCR. The isothermal nature of INAA-LFT ensures consistent conditions for nucleic acid amplification, establishing it as a crucial technology for rapid on-site pathogen detection. However, despite its considerable promise, the widespread application of isothermal INAA amplification-based lateral flow testing faces several challenges. This review provides an overview of the INAA-LFT procedure, highlighting its advancements in detecting plant viruses. Moreover, the review underscores the imperative to address existing limitations and emphasizes ongoing research efforts dedicated to enhancing the applicability and performance of this technology in the realm of rapid on-site testing.

Recent literature has seen a rapid expansion in the reference to front-end forensics as an indication of the untapped value of forensic science. While some of these contributions have centered on development of forensic intelligence from a single area of investigation, others call for a more fundamental change in the relationship between crime laboratories and policing, particularly relating early laboratory analysis with big datasets to provide leads to investigators. We highlight several recently implemented tactical strategies of crime laboratories that contribute to the body of forensic intelligence. Beyond the scientific gains from these tactical applications, the corresponding details on associated efficiencies, costs, time savings, and quality improvements offer insights towards patterns of success for the community of crime laboratories. Further details expand an interpretation of what constitutes success with an eye on the contributions of the crime laboratory towards public health, safety, and protection of the innocent in addition to societal gains from conviction of the guilty. The economic interpretation of the value provided by the forensic laboratory assists in the cost-benefit review of strategic and tactical decisions and supports the justification for laboratory public funding with measures of the return on investment from public support of the forensic laboratory

The short-lived positron-emitter carbon-11 (t1/2 = 20.4 min; b+, 99.8%) is prominent for labeling tracers for use in biomedical research with positron emission tomography (PET). Carbon-11 is produced for this purpose with a cyclotron, nowadays almost exclusively by the 14N(p,a)11C nuclear reaction, either on nitrogen containing a low concentration of oxygen (0.1–0.5%) or hydrogen (~ 5%) to produce [11C]carbon dioxide or [11C]methane, respectively. These primary radioactive products can be produced in high yields and with high molar activities. However, only [11C]carbon dioxide has some utility for directly labeling PET tracers. Primary products are required to be converted rapidly and efficiently into secondary labeling synthons to provide versatile radiochemistry for labeling diverse tracer chemotypes at molecular positions of choice. This review surveys known gas phase transformations of carbon-11 and summarizes the important roles that many of these transformations now play for producing a broad range of labeling synthons in carbon-11 chemistry.

The mechanical effects of membrane compositional inhomogeneities are analyzed in a process analogous of neck formation in cellular membranes. We cast on the Canham-Helfrich model of fluid membranes with both the spontaneous curvature and the surface tension being non-homogeneous functions along the cell membrane. The inhomogeneous distribution is determined by the equilibrium mechanical equations and the boundary conditions as considered in the axisymmetric setting compatible with the necking process. To establish the role played by mechanical inhomogeneity, we focus on the catenoid, a surface of zero mean curvature. Analytic solutions are shown to exist for the spontaneous curvature and the constrictive forces in terms of the border-radii. Our theoretical analysis shows that the inhomogeneous distribution of spontaneous curvature in a mosaic-like neck constrictional forces potentially contributing to the membrane scission under minimized work in living cells.

The way Norway is spearheading electrification in the transport sector is of global interest, and details of its policies and emission impacts represent a reference. We used the NERVE model, a bottom-up high-resolution traffic emission model, to calculate all exhaust emissions in Norway (2009-2020). This allows us to evaluate the co-benefit of policies to target climate change mitigation and air quality. We have analyzed local municipal data with regards to traffic growth, road network influences, vehicle composition, emissions and energy consumption. Light vehicle CO2 emissions per kilometre have been reduced by 22% since 2009, mainly driven by an increaseing bio-fuel mixing and BEV share. BEVs are mostly located in and around the main cities, areas with young vehicle fleets, and strong local incentives. Beneficiaries of all BEVs incentives have been a subset of the population with strong economic indicators. The incentivized growth in the share of diesel-fuelled passenger vehicle has been turned, and together with Euro6 emission standards, light vehicle NOx emissions have been halved since peaking in 2014. BEV represent an investment in emission reductions in years to come and current sales set up for an accelerated decline in emissions despite growth in traffic.

The on-state voltage of MOSFETs is a convenient and powerful temperature-sensitive electric parameter (TSEP) to determine the junction temperature, thus enabling device monitoring, protection, diagnostics and prognostics. The main hurdle in the use of the on-state voltage as a TSEP is the per-device characterization procedure, to be carried out in a controlled environment, with high costs. In this paper we compare two novel techniques for MOSFET junction temperature estimation: controlled shoot-through and direct heating by resistive heaters embedded in two Kapton (polyimide) films. Both allow in-place characterization of the TSEP curve with the device mounted in its final circuit and assembly, including the working heat sink. The two methods are also validated against the conventional procedure in a thermal chamber.

Introduction: In general, everyone believes that the smallest preterm infants should achieve normal intrauterine growth rates, but many thinks that this is not possible with current nutrition guidelines. There is resistance to giving enough nutrition for fear of "toxicity". The difference in weight Z-score between birth and a corrected gestational age (CGA) at discharge is assess in postnatal growth in our unit. Material and methods: An observational study was done between January 2018 and December 2020 where all cases that had ≤ 29 weeks of GA at birth and survived to 36 weeks corrected GA or that were discharged home. An aggressive nutrition protocol including parenteral as well as enteral nutrition was followed. Patients and their weight trajectory was plotted on the Fenton 2013 growth curve. The patients who had had a smaller WZP difference were also plotted. Results: A total of 32 cases were found. The median change in Z-score between birth and discharge of the whole group was -0.52 (IQR 0.53). Six of 32 (19%) had a more than one WZP, all of whom had severe pathologies. The median decline in Z score for this group with poor growth was 1.24 (IQR 0.22). There were 26 cases with a < 1 WZP (81%) and a median Z score fall of 0.39 (IQR 0.55). No important complications secondary to the ingested volumes or parenteral nutrition were reported. Conclusion: The group of cases with a > 1 WZP drop had severe pathologies. All the other cases had adequate growth parallel to normal weight growth charts and a few cases had some catch-up growth. The study showed that it is possible for many preterm infants to achieve normal intrauterine growth rates if they are given enough nutrition, but bigger multicenter studies are needed to confirm these findings.

Saiga (Saiga tatarica) was extirpated in China. Since Mid-1980s, attempts have been made for revival the species in the country, however, only a breeding herd of Saiga was successfully established at Wuwei, Gansu, China. The reintroduced Saiga population experienced a bumpy growth. Then, the population collapsed following the catastrophe die-off in the Saiga ranging countries in Central Asia, then population started to rebound when 6 new lams were born in 2019. After reviewing the population trend and conservation breeding of Saiga in China, we concluded that to establish a migratory species that needs vast range size like Saiga on central Asia steppe, an international collaboration is needed for introducing new genes. We recommend China to ratify the CMS in order to facilitate international conservation efforts to restoring the species in its former range.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

Manufacturing of grinding wheels is continuously adapting to new industrial requirements. New abrasives and new wheel configurations, together with wheel wear control allow for grinding process optimization. However, the wear behavior of the new abrasive materials is not usually studied from a scientific point of view due to the difficulty to control and monitor all the variables affecting the tribochemical wear mechanisms. In this work an original design of pin on disk tribometer is developed in a CNC grinding machine. An Alumina grinding wheel with special characteristics is employed and two types of abrasive are compared: White Fused Alumina (WFA) and Sol-Gel Alumina (SG). The implemented tribometer reaches sliding speeds of between 20 and 30 m/s and real contact pressures up to 190 MPa. The results show that the wear behavior of the abrasive grains is strongly influenced by their crystallographic structure and the tribometer appears to be a very good tool for characterizing the wear mechanisms of grinding wheels, depending on the abrasive grains.

Surface Plasmon Resonance (SPR) based sensors have the advantage of being label-free, enzyme-free and real-time. However, their spreading in multidisciplinary research is still limited and almost confined to prism-coupled devices. Plasmonic gratings, combined with a simple and cost-effective instrumentation, have been poorly developed compared to prism-coupled system mainly due to their lower sensitivity. Here we describe the optimization and signal enhancement of a sensing platform based on phase-interrogation method, which entails the exploitation of a nanostructured sensor. This technique is particularly suitable for integration of the plasmonic sensor in a lab-on-a-chip platform and can be used in a microfluidic circuit to ease the sensing procedures and limit the injected volume. The careful optimization of most suitable experimental parameters by numerical simulations leads to a 30 to 50% enhancement of SPR response, opening new possibilities for applications in the biomedical research field while maintaining the ease and versatility of the configuration.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

This article presents and discusses analytical data on the scientific publication record from 1910 to 2020 on two topics: "climate" and "climate change/global warming/climate emergency". The goal is to visualize how the publication record on these two topics has evolved over time, from different classification perspectives (year, country, source and organization). Three hypotheses are tested using data collected from Web of Science and various graphical representations of the data. It is found that research output related to the Earth’s contemporary changing climate overtook that of general climate research in 2011, and the publication ratio has been expanding in the last decade. There are significant differences in the publication countries and sources between the two topics, and conversely less significant differences in terms of organizations publishing these works. Differentiation factors that affect the level of research output and engagement on the climate challenge include: island versus landlocked nations, specialized versus general scientific journals, academic versus institutional organizations. The future of the publication records is discussed, such as the emergence of new terms to refer to the climate challenge, such as “climate emergency”.

The three-axis stabilization geostationary remote sensing satellite features high time resolution and plays a significant role in weather forecasting and environmental monitoring. With the future development of satellite technology, we propose a rapid geolocation algorithm for three-axis stabilization geostationary remote sensing satellites from the perspective of software algorithms. The method assesses conventional remote sensing data geolocation methods and the coordination group for meteorological satellites (CGMS, Coordination Group for Meteorological Satellites) nominal grid publishing format. First, the initial incident viewing vector of each detector on the sensor was constructed. Then, by reflecting the satellite platform's east-west and north-south mirrors, the outgoing vector of the payload coordinate system was obtained. This vector was converted to the satellite body coordinate system and, subsequently, to the satellite orbit coordinate system. The conversion of the earth-fixed coordinate system and the mirror rotation angle under ideal CGMS grid conditions were obtained, and the mirror rotation angle was converted to the corresponding CGMS nominal grid position to complete data positioning. The algorithm omits the complex process of calculating the intersection point between the viewing vector and the geodetic ellipsoid sphere from the earth-fixed coordinate system, resulting in an 83.3% improvement in computational efficiency without compromising positioning accuracy compared with conventional geolocation methods. This algorithm greatly improves the processing efficiency of geostationary meteorological satellite positioning, but its limitation is that the data processing results must be released in the CGMS nominal grid format.

Complexes of triply positive europium ion with organic ligands are popular objects for studying photophysical properties. This is related not only to the bright red emission of this 4f element, but also to some spectroscopic peculiarities of its luminescence: the first excited spin-orbit level (7F1) lies only about 300 cm−1 above the ground state (7F0), so that at room temperature its population is around 25–30%. However, such electronic structure of Eu(III) provides its paramagnetism under ordinary conditions. This fact is often ignored by researchers, which is shortsighted from the materials science point of view. A comprehensive and systematic study of the magnetic behavior for the Eu(III) molecular coordination compounds is a challenging task for the development of new polyfunctional materials. The present work presents synthesis, single crystal XRD analysis results, and a magnetic study for the firstly prepared europium(III) complexes with two neutral scorpionate ligands: trispyrazolylmethane (HCPz3) and its methylated analog, tris(3,5-dimethyl-1-pyrazolyl)methane (HC(PzMe2)3). The values of the spin-orbit coupling parameter obtained for Eu-trication by a theoretical approximation of the experimental magnetic susceptibility data are compared with those known for the scarce amount of the magnetically studied molecular compounds.

(1) Background: Since the pandemic, adolescent girls have increasingly faced mental health challenges. We examined prevalence trends and associated risk factors for depression among adolescent girls. 2) Methods: Data for girls aged 12 to 17 years (N=4346) from the 2021 cross-sectional National Survey on Drug Use and Health were analyzed. Factors associated with depression were examined using multiple regression analysis. (3) Results: Rates of severe depression were significantly higher (p&lt;.001) in older girls (adjusted odds ratio [AOR]: 1.63, 1.61, those who did not have authoritative parents (AOR: 3.40), and those with negative school experiences (AOR: 4.03). Black and Asian/Native Hawaiian or other Pacific Islanders were less likely to report severe depression than white girls. As previously reported, non-White girls were significantly less likely to receive treatment for depression (p&lt;.05). Parents’ characteristics and school experiences had no effect on the likelihood of receiving mental health treatment. (4) Conclusion: Depression has become increasingly common among American adolescent girls, who are now three times as likely as adolescent boys to have had recent experiences with depression. Our results show that family structure, parenting style, and negative school experiences significantly contribute to the rate of depression and that treatment disparities exist with regard to race and ethnicity.

This proposed research explores a novel approach to image classification by deploying a complex-valued neural network (CVNN) on a field-programmable gate array (FPGA), specifically for classifying 2D images transformed into polar form. The aim of this research is to address the limitations of existing neural network models in terms of energy and resource efficiency, by exploring the potential of FPGA-based hardware acceleration in conjunction with advanced neural network architectures like CVNNs. The methodological innovation of this research lies in the Cartesian to polar transformation of 2D images, effectively reducing the input data volume required for neural network processing. Subsequent efforts focused on constructing a CVNN model optimized for FPGA implementation, emphasizing the enhancement of computational efficiency and overall performance. The experimental findings provide empirical evidence supporting the efficacy of the image classification system developed in this study. One of the developed models, CVNN_128, achieves an accuracy of 88.3% with an inference time of just 1.6ms and a power consumption of 4.66mW for the classification of the MNIST test dataset consists of 10,000 frames. While there is a slight concession in accuracy compared to recent FPGA implementations that achieve 94.43%, our model significantly excels in classification speed and power efficiency—surpassing existing models by more than a factor of 100. In conclusion, the paper demonstrates the substantial advantages of FPGA-implementation of CVNNs for image classification tasks, particularly in scenarios where speed, resource, and power consumption are critical. The study’s reproducible results and corresponding code are available on GitHub at the following link: https://github.com/mahmad2005/CVNNonFPGA

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

Influence of reaction time on silver nanoparticles-catalyzed oxidation of 3,3’,5,5’-tetramethylbenzidine (TMB) was evaluated via probing the oxidation process by recording the UV-Visible absorbance of the resulting colored products of TMB oxidation by hydrogen peroxide in the presence of silver nanoparticles as peroxides mimics. The time curve of the oxidation process was constructed, revealed that the concentration of the oxidation product was increased by increasing the reaction time and then levled off because the nanozyme active nodes were saturated after a certain reaction time and consequently the steady-state condition can be observed. The maximal activity of the silver nanozymes was achieved after a very short reaction time as short as 3.0 min and after this time, the color intensity of the oxidation products remained constant, revealing saturation of active nodes of nanoparticles with nanozyme-substrate.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land

MultiCal is an affordable, high-precision measuring device designed for the on-site calibration of industrial robots. Its design features a long measuring rod with a spherical tip that is attached to the robot. By restricting the rod’s tip to multiple fixed points under different rod orientations, the relative positions of these points are accurately measured beforehand. A common issue with MultiCal is the gravity deformation of the long measuring rod, which introduces measurement errors into the system. This problem becomes especially serious when calibrating large robots, as the length of the measuring rod needs to be increased to enable the robot to move in a sufficient space. To address this issue, we propose two improvements in this paper. Firstly, we suggest the use of a new design of the measuring rod that is lightweight yet has high rigidity. Secondly, we propose a deformation compensation algorithm. Experimental results have shown that the new measuring rod improves calibration accuracy by 20% to 39%, while by using the deformation compensation algorithm, the accuracy increases by 6% to 16%. In the best configuration, the calibration accuracy is similar to that of a measuring arm with a laser scanner, producing an average positioning error of 0.274 mm and a maximum positioning error of 0.838 mm. The improved design is cost-affordable, robust, and has sufficient accuracy, making MultiCal a more reliable tool for industrial robot calibration.

Considering the actual world economical trends, one of the most important questions is now and in the future: how to reduce power consumption of electronic systems. Since the invention of computers, the electrical energy consumption step by step increased. Now when not only computers, but electric vehicles, robots, automation, and unmanned aerial vehicles play a very important role of our life, the main problem of system designers is how to reduce energy consumption in these systems. But also the existing already working systems must be revised in order to decrease their electric power consumption. The importance of this subject (energy control) shows that a huge number of research publications and survey papers deal with it. Just focusing on the last one or two years (2021 and 2022) the search hit 221000 titles (103000 hits only in 2022). Analyzing all the research areas is almost impossible, but focusing on some important research subjects, where one of the main topic is “energy saving methods” can give an overview about the subject. The paper focuses on the area of industrial robotic systems, electric vehicles, and embedded systems.

This article aims to reflect upon the relevance of Decolonization methodologies with the Theses on Feuerbach. Somehow, all the Indigenous scholars started from new Marxist like Paulo Freire, Frantz Fanon, but not from classic Marx. To us, the German Ideology of young Marx only resembles the pioneering sources of Indigenous methodology. This discussion is thus a reflection of our studies and a philosophic endeavor to talk about the marginal people of the world, and the scholars who engaged in and with the oppressed. However, we are not prepared to turn our attention away from all the vastness of Marx to a collection of potentially equally relevant to Indigenous methodology. This article concludes that the Theses on Feuerbach is the core of Marxist archaeology of knowledge or philosophy as a whole and has been wading in the Indigenous paradigm.

The contactless coalescence of a droplet is of paramount importance for physical and industrial applications. This paper describes a coalescence method in mid-air via acoustic levitation using an ultrasonic phased array system. Acoustic levitation using ultrasonic phased arrays provides promising lab-on-a-drop applications, such as transportation, coalescence, mixing, separation, evaporation, and extraction in a continuous operation. The mechanism of droplet coalescence in mid-air may be better understood by experimentally and numerically exploring the droplet dynamics immediately before the coalescence. In this study, water droplets were experimentally levitated, transported, and coalesced by controlling acoustic fields. We observed that the edge of droplets deformed and attracted each other immediately before the coalescence. Through image processing, the radii of curvature of the droplets were quantified and the pressure difference between the inside and outside the droplet was simulated to obtain the pressure and velocity information on the droplet surface. The results revealed that the sound pressure acting on the droplet clearly decreased before the impact of the droplets. This pressure on the droplets was quantitatively analyzed from the experimental data. Our experimental and numerical results provide deeper physical insights into contactless droplet manipulation for futuristic lab-on-a-drop applications.

Marine mortar was the goal material and its multi-scale physical-chemical-mechanical characteristics were the principal interest in this study. The on-line multi-scale damage detection experiments art was designed to quantify the characteristics mathematically and graphically. The normal cylinder specimen with 70-day age was produced and investigated by dynamically global MSHCT scan and local detection of EDS, SEM and XRD. The experiments results indicated that the marine mortar offered the appreciable strength at the early age at least, although some saline minerals were generated during the preparation. The micro-interfacial behavior and the parental foci controlled the damage development of the marine mortar the performance of which was still the adjustable one by the composition optimization.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

This study was aimed to investigate the effect of capital structure on firms’ profitability with special emphasis on Ethiopian Large Private Manufacturing Firms using panel data of five consecutive years (2006/07-2010/11G.C). The secondary data sources (audited financial statements) have been collected from the randomly selected thirty three large private manufacturing firms in Ethiopia. Linear regression model has been employed to analyze the relationship between firms’ profitability and capital structure. Specifically, Random-effect Generalized Least Square of panel data regression model has been selected to empirically test the literature driven hypotheses. Finally, the findings of this study revealed that a significant positive relationship between firms’ profitability and total debt ratio which indicate firm’s capital structure.

Space-based gravitational wave detection is extremely sensitive to disturbances. The Keplerian configuration cannot accurately reflect the variations in spacecraft configuration. Planetary gravitational disturbances are one of the main sources. Numerical simulation is an effective method to investigate the impact of perturbation on spacecraft orbits. This study shows that, in the context of the Taiji project, Earth’s gravity is an essential factor in the change in heliocentric formation configuration, contributing to the relative acceleration between spacecrafts in the order of O(10−6)m·s−2. Considering 00:00:00 on October 27, 2032 as the initial orbiting moment, under the influence of Earth’s gravitational perturbation, the maximum relative change in armlengths and variation rates of armlengths for Taiji is 1.6×105km, 32m·s−1 respectively, compared with the unperturbed Keplerian orbit. Additionally, by considering the gravitational perturbations of Venus and Jupiter, the armlength and relative velocity for Taiji are reduced by 16.01% and 17.45%, respectively, compared with when only considering that of Earth. The maximum amplitude of the formation motion indicator changes with the orbit entry time. Results show that the relative velocity increase between the spacecrafts is minimal when the initial orbital moment occurs in July. Moreover, the numerical simulation results are inconsistent when using different ephemerises. The differences between ephemeris DE440 and DE430 are smaller than those between DE440 and DE421.

The new observations, including the fastest star, the circular velocity curve of the Milky Way and the fast galaxy bar, should imply that the mass of the center of the Milky Way is almost 10¹¹ times the mass of the Sun.

Pure orbital blowout fractures occur within the confines of the internal orbital wall. Restoration of orbital form and volume is paramount to prevent functional and esthetic impairment. The anatomical peculiarity of the orbit has encouraged surgeons to develop implants with customized features to restore its architecture. This has resulted in worldwide clinical demand for patient-specific implants (PSIs) designed to fit precisely in the patient's unique anatomy. Fused filament fabrication (FFF) three-dimensional (3D) printing technology has enabled the fabrication of implant-grade polymers such as Polyetheretherketone (PEEK), paving the way for a more sophisticated generation of biomaterials. This study evaluates the FFF 3D printed PEEK orbital mesh customized implants with a metric considering the relevant design, biomechanical, and morphological parameters. The performance of the implants is studied as a function of varying thicknesses and porous design constructs through a finite element (FE) based computational model and a decision matrix based statistical approach. The maximum stress values achieved in our results predict the high durability of the implants, and the maximum deformation values were under one-tenth of a millimeter (mm) domain in all the implant profile configurations. The circular patterned implant (0.9 mm) had the best performance score. The study demonstrates that compounding multi-design computational analysis with 3D printing can be beneficial for the optimal restoration of the orbital floor.

Biomaterials play an important role in the development of advancing three dimensional (3D) in vitro skin models, providing valuable insights for drug testing and tissue-specific modeling. Commercial materials, such as collagen, fibrin or alginate, have been widely used in skin modelling. However, they do not adequately represent the molecular complexity of skin components. On this regard, the development of novel biomaterials that represent the complexity of tissues are becoming more important in the design of advanced models. In this study, we have obtained aged human decellularized dermal extracellular matrix (dECM) hydrogels extracted from cadaveric human skin and demonstrated their potential as scaffold for advanced skin models. These dECM hydrogels effectively reproduce the complex fibrillar structure of other common scaffolds, exhibiting similar mechanical properties, while preserving the molecular composition of the native dermis. It is worth noting that fibroblasts embedded within human dECM hydrogels exhibit behavior more representative of natural skin compared to commercial collagen hydrogels, where uncontrolled cell proliferation leads to material shrinkage. The described human dECM hydrogel is able to be used as scaffold for dermal fibroblasts in a skin aging on chip model. These results demonstrate that dECM hydrogels preserve essential components of the native human dermis making them a suitable option for the development of 3D skin aging models that accurately represent the cellular microenvironment, improving existing in vitro skin models and allowing for more reliable results in dermatopathological studies.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

Aeromagnetic compensation plays a vital role in geomagnetic navigation and has received considerable attention throughout last few decades. Classical aeromagnetic compensation methods based on the Tolles–Lawson (T-L) model are mainly aimed at permanent, induced, and eddy-current magnetic interferences of aircraft platform, which ignores other stray magnetic field interference on the platform including the interferences caused by on-board electronic (OBE) systems. In order to cooperate with TL model, magnetometers are usually required to be installed on the extension rod outside the cabin, which is widely applied to geophysical magnetic survey. In order to ensure safety and reduce the cost of platform modification in geomagnetic navigation, it’s necessary to place magnetometers inside the cabin. It also further exacerbates the magnetic interferences and improves the difficulty of magnetic compensation. In this paper, a modified aeromagnetic compensation method is proposed, and the in-cabin OBE interferences are respectively modelled to be proportional to the currents and their temporal variations of different electronic devices. To ensure that modified model adapts to strong OBE interference in the cabin, a cut-off frequency determination method based on curvature calculation and a feature selection method based on correlation calculation are proposed. The cut-off frequency determination method helps to select passband filter which suitable for in-cabin OBE interference. The feature selection method can help to effectively select current and voltage inputs for modified model. In addition, principal component analysis (PCA) is adopted to reduce multicollinearity which is intensified by the extension of OBE interferences in coefficient-estimating. Experiments on public dataset are conducted to illustrate the effectiveness of the proposed method, and the best compensation result achieved 1.71nT of root mean square error (RMSE).

This study presents the design and implementation of a PLC microprocessor adhering to the IEC-61131-3 standard, executed on a Cyclone-V FPGA using a DE10-NANO development board. Our microprocessor optimizes the central processing unit by streamlining the data path, achieving a remarkable simulated response time of approximately 60 ns, equivalent to three clock cycles at a 50MHz frequency for Boolean operations. To substantiate our approach, we conducted practical experiments utilizing a FESTO conveyor station, employing relays as actuators, and incorporating optical and inductive sensors. The results underscore the feasibility of our proposed approach and serve as practical validation of its efficacy. This work introduces a promising avenue for the development of cost-effective PLCs employing SoC FPGA variants. Additionally, a thorough comparison of execution times with other early reported architectures. Our microprocessor outperforms even well-established PLCs like the S7-312, with substantial reductions in execution times of 94.54% for floating-point operations, 71.42% to 93.33% for word operations, and up to 78.57% for bit operations.

This study sought to evaluate the awareness, comprehension, and practices concerning Forensic Odontology among dental students and faculty at a Dental School in Cyprus. An online, cross-sectional, descriptive survey was disseminated to the entirety of dental students and faculty of the School of Dentistry, European University Cyprus, in November 2022. Of those surveyed, 47 faculty members and 304 students responded, yielding response rates of 66.2% and 80%, respectively. The survey revealed that 87% of faculty and 65% of students were familiar with Forensic Odontology. A noteworthy 94% of faculty and 85% of students recognized teeth as DNA repositories. A high percentage, 98% of faculty and 89% of students, acknowledged the role of Forensic Odontology in the identification of criminals and deceased individuals. Awareness of age estimation through dental eruption patterns was evident in 85% of faculty and 81.6% of students. A substantial proportion (80% of faculty) maintained dental records, while 78% of students recognized the importance of dental record-keeping in ensuring quality care. Interestingly, 57% of students and 64% of faculty were aware of the possibility of dentists testifying as expert witnesses. The majority, 95.7% of faculty and 85% of students, concurred that physical harm, scars, and behavioral alterations predominantly indicate child abuse. The survey underscored a robust awareness of Forensic Odontology among respondents. Despite faculty's comprehensive understanding, there's a pronounced need to bolster their inclination towards attending relevant seminars. Emphasis on improved record-keeping practices for potential forensic applications is paramount.