In this paper, we introduce and study the notion of rough I₂-lacunary statistical convergence of double sequences in normed linear spaces. We also introduce the notion of rough I₂-lacunary statistical limit set of a double sequence and discuss about some properties of this set.

A plasmonic refractive index (RI) sensor based on metal-insulator-metal (MIM) waveguide coupled with concentric double rings resonator (CDRR) is proposed and investigated numerically. Utilizing the novel supermodes of the CDRR, the FWHM of the resonant wavelength can be modulated, and a sensitivity of 1060 nm/RIU with high figure of merit (FOM) 203.8 is realized in the near-infrared region. The unordinary modes as well as the influence of structure parameters on the sensing performance are also discussed. Such plasmonic sensor with simple framework and high optical resolution could be applied to on-chip sensing systems and integrated optical circuits. Besides, the special cases of bio- sensing and triple rings are also discussed.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

With the development of the city, a large number of water networks in the built-up areas of Bangkok have been filled and hardened, resulting in poor urban flooding and aggravating flooding, causing loss of life and property of citizens. In this paper, on the basis of combing the current water networks and open space potential flood storage points in the built-up areas of Bangkok, the complex network diagram of the water system in the built-up areas of Bangkok is constructed by combining the theory of complex networks and analyzing the attribute parameters of the network and the characteristic parameters of the open space storage nodes and water system paths, and finding that the water system network in the built-up area of Bangkok has complex network characteristics such as robustness, clustering and hierarchy. By exploring the key storage points and water system connection paths, the researchers initially constructed a flood safety pattern in the built-up area of Bangkok with 145 key nodes and 127 river paths as the backbone, and conceptualized the development study of the flood safety pattern in both horizontal and vertical directions. The urban flood safety pattern based on complex network theory proposed in this paper provides a case reference and methodological ideas to scientifically solve the game conflict between the demand for construction land for urban development and the construction area of urban open space storage points and water storage network under the increasingly severe flooding situation.

Background In this study, we describe our clinical experience with the fifth-generation of a breast implant with a smooth, fine surface from a Korean manufacturer (BellaGel^Ò SmoothFine; HansBiomed Co. Ltd., Seoul, Korea) in Asian women. Methods We analyzed 223 women (mean age=35.28±9.45 years and mean follow-up period=12.03±2.48 months), comprising 118 bilateral cases and 109 unilateral ones, who received breast augmentation using the BellaGel^Ò SmoothFine at our hospital between June 4, 2018 and February 28, 2019. For safety assessment, we analyzed frequencies of postoperative complications and overall survival of the BellaGel^Ò SmoothFine. Results Postoperatively, complications (12 cases, 5.38%) include asymmetry (3 cases, 1.35%), hematoma (2 cases, 0.90%), hypertrophic scars (2 cases, 0.90%), wound disruption (2 cases, 0.90%), rippling (1 case, 0.45%), capsular contracture (1 case, 0.45%), stretch deformities with skin excess (1 case, 0.45%). In addition, time-to-events were calculated as 10.94±0.64 months (95% CI 9.69-12.19) and the survival rate reached 0.290±0.168 (95% CI 0.094-0.901) at 12 months postoperatively. Conclusions Here, we describe our clinical experience with the BellaGel^Ò SmoothFine. Our results are of significance in that this is the first report about the fifth-generation of a breast implant with a smooth, fine surface from a Korean manufacturer in Asian women.

Composite materials are widely used in the dental field in clinics as biomaterials. For example, it has been used as a biomaterial to repair caries and restore masticatory function, and as a cement to adhere the restoration to the tooth substrate. In order to demonstrate its function, dental biomaterials are measured their mechanical strength. From such basic research, we explained the potential of dental biomaterials, especially flexural strength and modulus of elasticity. Mechanical properties of dental biomaterials similar to those of the tooth, thermal stimulation, and aesthetic elements in the oral cavity. In this part, we will introduce the commercialized products of composites suitable for the characteristics and tooth quality, and provide the reader with the characteristics from the flexural characteristics of the composite materials used in clinical dentistry. In clinical performance, it might be advisable to delay polishing when composite biomaterials are used for luting materials, filling materials and core build-up materials since improved the flexural strength and the flexural modulus of elasticity were displayed after 1-day storage. And it is thought that flexural strength or characteristics is a significant important mechanical property of oral biomaterials.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

With increasing interest in the use of additive manufacturing techniques in the construction industry, static rheological properties of fresh concrete have necessarily come into focus. In particular, the knowledge and control of static yield stress (SYS) and its development over time are crucial for mastering formwork-free construction, e.g. by means of layered extrusion. Furthermore, solid understanding of the influences of various concrete constituents on the initial SYS of the mixture and the structural build-up rate is required for purposeful material design. This contribution is concentrated on the effect of aggregates on these rheological parameters. The volume fraction of aggregates was varied in the range of 35 to 55 % by volume under condition of constant total surface area of the particles. The total surface area per unit volume of cement paste was equal to 5.00, 7.25 and 10.00 m²/l, conditioned on the constant volume fraction of aggregates. Both variations were enabled by changing the particle size distributions of the aggregates while holding the cement paste composition constant for all concrete mixtures. To characterise the SYS and the structural build-up, constant shear rate tests with a vane-geometry rotational rheometer were performed. It was found that in the ranges under investigation the variation in volume fraction had a more pronounced effect on the static rheological properties of concrete than did the variation in surface area. An accurate mathematical description of the relationship between the initial SYS of concrete and the relative volume fraction of aggregate based on the Chateau-Ovarlez-Trung model was proposed. Challenges in deriving a similar relationship for the structural build-up rate of concrete were highlighted.

Background: Although transcatheter arterial chemoembolisation (TACE) is the standard of care for intermediate-stage hepatocellular carcinoma (HCC), this is a largely heterogeneous disease that includes a subgroup of patients who do not benefit from TACE. The treatment strategy for this subgroup of patients currently remains an unmet need in clinical practice. Here, we performed a proof-of-concept study that lenvatinib may be more favourable treatment option over TACE as an initial treatment in intermediate-stage HCC patients with large or multinodular tumours exceeding the up-to-seven criteria. Methods: This proof-of-concept study included 642 consecutive patients with HCC initially treated with lenvatinib or conventional TACE (cTACE) between January 2006 and December 2018. Of these patients, 176 who received lenvatinib or cTACE as an initial treatment and met the eligibility criteria [unresectable, beyond the up-to-seven criteria, no prior TACE/systemic therapy, no vascular invasion, no extrahepatic spread and Child-Pugh A liver function] were selected for the study. Propensity score matching was used to adjust for patient demographics. Results: After propensity-score matching, outcome of 30 patients prospectively treated with lenvatinib (14 in clinical trials, 1 in early access program and 15 in real world setting) and 60 patients treated with cTACE as the initial treatment was compared. The change of ALBI score from baseline to the end of treatment were -2.61 to -2.61 for 30 patients in lenvatinib group (p = 0.254) and -2.66 to -2.09 in cTACE group (p < 0.01), respectively. The lenvatinib group showed a significantly higher objective response rate (73.3% vs. 33.3%; p < 0.001) and significantly longer median progression-free survival than the cTACE group (16.0 vs. 3.0 months; p < 0.001). Overall survival was significantly longer in the lenvatinib group than in the cTACE group (37.9 vs. 21.3 months; hazard ratio: 0.48, p < 0.01). Conclusion: In patients with large or multinodular intermediate-stage HCC exceeding the up-to-seven criteria with Child-Pugh A liver function, who usually do not benefit from TACE, lenvatinib provides more favorable outcome than TACE.

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

Shape-shifting polymers are widely used in various fields such as intelligent switches, soft robots and sensors, which require both multiple stimulus response functions and qualified mechanical strength. In this study, a novel near infrared light (NIR) responsible shape-shifting hydrogel system was designed and fabricated, through embedding vinylsilane modified carbon nanotubes (CNTs) into particle-double network (P-DN) hydrogels by micellar copolymerization. The dispersed brittle Poly(sodium 2-acrylamido-2-methylpropane-1-sulfonate) (PNaAMPS) network of the microgels can serves as sacrificial bonds to toughen the hydrogels, and the CNTs endow it NIR photothermal conversion ability. The results show that the CNTs embedded P-DN hydrogels present excellent mechanical strength, i. e. fracture strength of 312 kPa and fracture strain of 357%. Moreover, an asymmetric bilayer hydrogel, where the active layer contains CNTs, can achieve 0°–110° bending deformation within 10 min under NIR irradiation and can realise complex deformation movement. This study provides a theoretical and experimental basis for the design and manufacture of photoresponsive soft actuators.

Corrugated board, widely used in the packing industry, is a recyclable and durable material. Its strength and cushioning, influenced by geometry, environmental conditions like humidity and temperature, and paper quality, make it versatile. Double-walled (or five-ply) corrugated board, comprising two flutes and three liners, enhances these properties. This study introduces a novel approach to analyze 5-layered corrugated board, extending a previously published algorithm for single-walled boards. Our method focuses on measuring layer and overall board thickness, flute height, and center lines of each layer. Integrating image processing and genetic algorithms, the research successfully developed an algorithm for precise geometric feature identification of double-walled boards. Images were recorded using a special device with a sophisticated camera and image sensor for detailed corrugated board cross-sections. Demonstrating high accuracy, the method faced limitations only with very deformed or damaged samples. This research contributes significantly to quality control in the packaging industry and paves the way for further automated material analysis using advanced machine learning and image sensors. It emphasizes the importance of sample quality and suggests areas for algorithm refinement to enhance robustness and accuracy.

Ionizing radiation-induced damage in cancer and normal cells leads to apoptosis and cell death, through the intracellular oxidative stress, DNA damage and disorders of their metabolism. Irradiation doses that do not lead to the death of tumor cells can result in the emergence of radioresistant clones of these cells, due to the rearrangement of metabolism and the emergence of new mutations, including those in the genes responsible for DNA repair. The search for the substances capable of modulating the functioning of the tumor cell repair system is an urgent task. Here we analyzed the effect of cerium(III) fluoride nanoparticles (CeF3 NPs) on normal (human mesenchymal stem cells – hMSCs) and cancer (MCF-7 line) human cells after X-ray radiation. CeF3 NPs effectively prevent the formation of hydrogen peroxide and hydroxyl radicals in an irradiated aqueous solution, showing pronounced antioxidant properties. CeF3 NPs are able to protect hMSCs from radiation-induced proliferation arrest, increasing their viability and mitochondrial membrane potential, and, conversely, inducing the cell death of MCF-7 cancer cells, causing radiation-induced mitochondrial hyperpolarization. CeF3 NPs provided a significant decrease in the number of double-strand breaks (DSBs) in normal cells, while in MCF-7 cells the number of γ-H2AX foci dramatically increased in the presence of CeF3 4 hours after irradiation. In the presence of CeF3 NPs, there was a tendency to modulate the expression of most analyzed genes associated with the development of intracellular oxidative stress, cell redox status and the DNA repair system after X ray irradiation. Cerium-containing nanoparticles are capable of providing selective protection of normal cells from radiation-induced injuries and are considered as a platform for the development of promising clinical radioprotectors.

Bone Scan Index (BSI) is an image biomarker for quantification on bone metastasis of cancers. To compute BSI, not only the hotspots (metastasis) but also the bones have to be segmented. Most related researches focus on binary classification on bone scintigraphy: having metastasis or none. Rare studies focus on pixelwise segmentation. In this study we compare three advanced convolutional neural network (CNN) based models to explore the bone segmentation on dataset in house. The best model is Mask R-CNN, which reaches the precision, sensitivity and F1-score: 0.93, 0.87, 0.90 for prostate cancer patients and 0.92, 0.86, 0.88 for breast cancer patients, respectively. The results are the average of 10-fold cross-validation, which reveals the reliability for clinical use on bone segmentation.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

In order to improve the operation performance of the multi-stage double-suction centrifugal pump and reduce the internal energy loss of the pump, this paper proposes a single-objective optimization design method based on non-hierarchical response surface model (RSM) and the multi-island genetic algorithm (MIGA). Nine parameters, such as the blade outlet width and blade wrap angle, were used as design variables, and the optimization objective was the efficiency under design conditions. In total, 149 sets of valid data were obtained under the latin hypercube sampling method (LHS), the corresponding thresholds were set for efficiency and head, and 99 sets of valid data were obtained. A cross-validation analysis of the sieved data was carried out based on non-hierarchical RSM, global optimization of the efficiency was carried out using MIGA, and numerical verification was carried out via CFD. The research results show that compared with hierarchical RSM, non-hierarchical RSM can approximate the nonlinear relationship between the objective function and the design variables with higher accuracy, and the model fitting R2 value was 0.919. The efficiency was improved by 3.717% after optimization. The overall prewhirl of the impeller inlet after optimization decreased, the internal speed of the volute significantly improved, the large-area vortex at the volute and the outlet pipe was eliminated, the impact loss at the volute separating tongue disappeared, and the overall hydraulic performance of the pump was improved. The total entropy output value of the optimized pump was reduced by 4.79 (W/K), mainly concentrated in the reduction in the entropy output value of the double volute, and the overall energy dissipation of the pump was reduced.

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

The method of regularized stokeslets is widely-used to model microscale biological propulsion. The method is usually implemented with only the single layer potential, with the double layer potential being neglected, despite this formulation often not being justified a priori due to non-rigid surface deformation. We describe a meshless approach enabling inclusion of the double layer which is applied to several Stokes flow problems in which neglect of the double layer is not strictly valid: the drag on a spherical droplet with partial slip boundary condition, swimming velocity and rate of working of a force-free spherical squirmer, and trajectory, swimmer-generated flow and rate of working of undulatory swimmers of varying slenderness. The resistance problem is solved accurately with modest discretization on a notebook computer with the inclusion of the double layer ranging from no-slip to free slip limits; neglect of the double layer potential results in up to 24% error, confirming the importance of the double layer in applications such as nanofluidics, in which partial slip may occur. The squirming swimmer problem is also solved for both velocity and rate of working to within a few percent error when the double layer potential is included, but the error in the rate of working is above 250% when the double layer is neglected. The undulating swimmer problem by contrast produces a very similar value of the velocity and rate of working for both slender and non-slender swimmers, whether or not the double layer is included, which may be due to the deformation’s `locally rigid body’ nature, providing empirical evidence that its neglect may be reasonable in many problems of interest. Inclusion of the double layer enables us to confirm robustly that slenderness provides major advantages in efficient motility despite minimal qualitative changes to the flow field and force distribution.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

China is in the climbing phase of the "Inverted U" environmental Kuznets curve, from excessive environmental consumption to the development stage of governance and protection, and green innovation. It is the most complex period of environmental quality. Environmental and policy regulation are very important. Select panel data of 29 provinces of China (excluding Hong Kong, Macau, Taiwan, Hainan and Tibet) from 2008 to 2017, construct a nonlinear two-threshold regression model, empirically analyse the impact of environmental tax and government innovation subsidies to green processes innovation, and attempt to explore whether the implementation of these two policies at the same time can make enterprises more inclined to green process innovation and whether there is an optimal space for policy implementation. It is proposed that the synergy effect of environmental tax and government innovation subsidy policies on enterprise green process innovation should be fully utilized, and the enterprise green process innovation environment and incentive mechanism should be improved to promote the green transformation and sustainable development of enterprises.

In the paper, the author finds bounds of the sine and cosine along a circle on the complex plane in terms of two double inequalities for the norms of the sine and cosine along a circle on the complex plane.

Suzuki cross-coupling reaction has developed one of the furthermost effectual approaches for the synthesis of biaryls or substituted aromatic moieties from aryl halides and arylboronic acids with a palladium-catalyst in the past two era’s. Herein, Pd-free layered double hydroxide containing nickel catalysts were prepared by co-precipitation method under ultrasonic irradiation and N2 atmosphere with different molar ratios of Ni: Mg: Al and coded as (1NiLDHs-Dr), (1.5NiLDHs-Dr) and (2NiLDHs-Dr). A series of reduced catalysts under 5%H2/N2 at different temperatures were coded as 1NiLDHs-R200, 1.5NiLDHs-R200 and 2NiLDHs-R200. As-synthesized 2NiLDHs-Dr was the superlative catalyst when coupling different aryl halides with different boronic acids derivatives. Deep investigation of all catalysts was done using different techniques such as inductively coupled plasma optical emission spectroscopy (ICP-OES), x-ray photoelectron spectroscopy (XPS), powder x-ray diffraction (XRD), thermogravimetric analyses (TGA), Fourier transfer infrared (FTIR), scanning electron microscope (SEM) connected with energy dispersive x-ray (EDX) and N2-physisorption at -196 ℃. The results attained verified that ɑ-Ni(OH)2 was fashioned for 2NiLDHs-Dr catalyst and the enclosure of nickel ions in the cationic sheet of layered structure were responsible for the fascinating catalytic efficacy rather than the basic nature of material. The Ni-containing LDHs catalysts encourage forthcoming studies in Pd-free catalyzed C-C coupling reactions.

Count data are used in many fields of practice, especially Poisson distribution as a popular choice for the marginal process distribution. If these counts exhibit serial dependence, a popular approach is to use a Poisson INAR(1) model to describe the autocorrelation structure of process. In this paper, the explicit formulas are proposed to evaluate performance characteristics of Double Moving Average control chart (DMA) for Integer valued autoregressive of serial dependence Poisson process. The characteristics of the control chart are frequently measured as Average Run Length (ARL) which means that the average of observations are taken before a system is signaled to be out-of-control. These proposed explicit formulas of ARL are simple and easy to implement for practitioner. The numerical results show that the DMA chart performs better than others when the magnitudes of shift are moderate and large.

The licensing of new reactors implies the use of verified and validated neutronics codes. Numerical validation can rely on sensitivity and uncertainty studies but they require repeated execution of time-consuming neutron flux and depletion calculations. The computational costs can be shortened by using perturbation theories. However, Depletion Perturbation Theory is restricted to single integral values such as a nuclide density. Relying on reduced basis approaches, which reconstruct the whole nuclide densities at once, is one way to get around this restriction. Furthermore, the adjoint-based reduced-order model uses the direct and adjoint equations for the projection. For diffusion or transport calculations, Exact-to-Precision Generalized Perturbation Theory has been developed. Still, no models for depletion calculations are readily available. Therefore, this paper describes a novel adjoint-based reduced order model for the Bateman equation. It uses a range-finding algorithm to create the basis and the Depletion Perturbation Theory for the reconstruction of the nuclide densities at first order. Our paper shows that for several perturbed cases, the depletion reduced-order model successfully reconstructs the nuclide densities. As a result, this serves as a proof of concept for our adjoint-based reduced order model which can perform sensitivity and uncertainty burn-up analysis in a shorter time.

Objectives of this study were to investigate effects of repeated superstimulation on the success of ovum-pick up and in vitro production of embryos (OPU-IVP) and donor health and evaluate the efficiency of a modified SOF sequential medium in producing viable embryos. Over 1 y, six cross-bred beef heifers and three beef cows were subjected to superstimulations and OPU-IVP. Oocytes recovered were used for in vitro embryo production and the resulting embryos were transferred as fresh or frozen-thawed. Number of follicles, oocytes recovered, cleavage and blastocyst rates substantially varied among individuals. However, repeated trials did not significantly affect the efficiency of OPU-IVP. The pregnancy rates (PR) 22 to 30 d after embryo transfer for in vitro-derived fresh embryos was similar to that of fresh in vivo embryos, whereas transfer of in vitro-derived frozen embryos reduced PR compared to frozen-thawed in vivo embryos. All recipient heifers diagnosed pregnant delivered a viable calf, suggesting developmental competence of the embryos. Repeated OPU-IVP had no apparent deleterious effects, as all donors had viable calves after ET. We concluded that multiple OPU-IVP cycles can be effectively performed for a prolonged interval to maximize embryo production from elite donors without compromising their reproductive health.

Data from the WHO and UNICEF Estimates of National Immunization Coverage (WUENIC) 2022 revision were analyzed to assess the status of routine immunization in the WHO African Region, disrupted by the COVID-19 pandemic. In 2022, the coverage with the first and third dose of diphtheria-tetanus-pertussis containing vaccine (DTP1 and DTP3 respectively) and with the first dose of measles-containing vaccine (MCV1), in the region, was estimated at 80%, 72% and 69%, respectively (all below the 2019 level). Only 13 of the 47 countries (28%) achieved the global target coverage of 90% or above with DTP3 in 2022. From 2019 to 2022, 28.7 million zero-dose were recorded (19.0% of target population). Ten countries of the region accounted for 80.3% of all zero-dose children including the four most populous countries (Nigeria, Ethiopia, Democratic Republic of the Congo, United Republic of Tanzania). Reported administrative coverage greater than WUENIC was found in 19 countries, highlighting routine immunization data quality issues. The WHO African region has not yet recovered from COVID-19 disruptions to routine immunization. It is critical for Governments to ensure that processes are in place to prioritize investments for restoring immunization services, catching-up on vaccination of zero-dose and un-der-vaccinated children and improving data quality.

In regions with limited precipitation information like Peru, many studies rely on precipitation data derived from satellite products (SPPs) and reanalysis products. These products provide near-real-time information and offer global spatial coverage, making them attractive for various applications. However, it is essential to consider their uncertainties when conducting hydrological simulations, especially in a key region like the Pacific drainage (Pd), where 56% of Peruvian population resides (including the capital Lima). This study evaluates the performance of three precipitation products: Reanalysis, ERA5-Land (top down approach), and two SPPs: GPM+SM2RAIN and SM2RAIN-ASCAT (bottom-up approaches). Hydrological modeling was conducted on 30 basins distributed across the Pd, which were grouped into five regions (I-V, ordered from south to north). The results showed that SM2RAIN-ASCAT performed well in regions I-III-IV, ERA5-Land in region II, and GPM+SM2RAIN in region V. The hydrological model GR4J was tested, and better efficiency criteria were obtained with SM2RAIN-ASCAT and GPM+SM2RAIN when comparing simulated versus observed streamflows. The hydrological modeling with SM2RAIN-ASCAT and GPM+SM2RAIN demonstrated satisfactory efficiency metrics (KGE > 0.75; NSE > 0.65). Additionally, ten hydrological signatures were quantified to assess the variability of simulated streamflows in each basin, with metrics such as Mean Flow (Q mean), 5th Quantile Flow (Q5), and 95th Quantile Flow (Q95) showing overall better performance. Finally, the results of this study demonstrate the reliability of using bottom-up satellite products in Pd basins.

MRI is the gold standard for treatment response assessment in glioblastoma. However, there is no consensus regarding the optimal interval for MRI follow-up during standard treatment. Moreover, reliable assessment of treatment response is hindered by the occurrence of pseudoprogression. It is unknown if a radiological follow-up strategy with 2-3 months intervals actually benefits patients and how it influences clinical decision making about continuation or discontinuation of treatment. This study assessed the consequences of scheduled follow-up scans (post-chemoradiotherapy [post-CCRT], after 3 cycles of adjuvant chemotherapy [TMZ3/6], after completion of treatment [TMZ6/6]) and unscheduled scans on treatment decisions during standard concomitant and adjuvant treatment in glioblastoma patients. Additionally, we evaluated how often follow-up scans resulted in diagnostic uncertainty (tumor progression versus pseudoprogression), and whether perfusion MRI improved clinical decision making. Scheduled follow-up scans during standard treatment in glioblastoma patients rarely resulted in early termination of treatment (2.3% post-CCRT, 3.2% TMZ3/6, and 7.8% TMZ6/6), but introduced diagnostic uncertainty in 27.7% of cases. Unscheduled scans resulted in more major treatment consequences (30%; p&lt;0.001). Perfusion MRI caused less diagnostic uncertainty (p=0.021) but did not influence treatment consequences (p=0.871). This study does not support the current pragmatic follow-up strategy and suggests a more tailored follow-up approach.

We calculate energies of shallow donors confined in a rolled-up quantum well in the presence of the electric field by solving numerically the Schrödinger equation in natural curvilinear coordinates. It is found that the curves of density of states (DOS) are very sensitive to the variation of the donor position, the geometry of the spiral and the applied electric field value. Novel results for dependencies of donor’s dipole moment and its polarizability on the electric field strength and its orientation, for different donor positions are presented. Also, we found that anisotropic Stark effect of the first order provides in this structure a dependency of the polarizability on the external electric field in a spike-like shape, giving rise to a sharp variation of the dipole moment.

Background: The currently advised follow-up scheme of PSA-testing after robot-assisted radical prostatectomy (RARP) is strict and might pose a burden to our healthcare system. We aimed to optimize the 1-year follow-up scheme for patients who undergo RARP. Methods: All patients with histologically-proven prostate cancer (PCa) who underwent RARP between 2018 and August 2022 in the Prostate Cancer Network the Netherlands were retrospectively evaluated. We excluded patients who underwent salvage RARP and patients who had &lt;1 year of PSA follow-up. Postoperative PSA-values were collected. Biochemical persistence (BCP) was defined as PSA-level &gt;0.10 ng/mL at 0-4 months after RARP, whereas biochemical recurrence (BCR) was defined as PSA-level &gt;0.2 ng/mL at any time point after RARP. We aimed to identify a group of patients who had a very low risk of BCR at different time-points after surgery. Results: Of all 1155 patients, BCP was observed in 151 (13%), of whom 79 (6.8%) had PSA ≥0.2 ng/mL. BCR further developed in 51 (4.7%), and 37 (3.4%) patients at 5-8 and 9-12 months after RARP, respectively. In 12 patients, BCR was found at 5-8 months after RARP in absence of BCP. These patients represented 1.2% (12/1004) of the entire group. In other words, 98.8% (992/1004) of patients who had an unmeasurable PSA-level at 0-4 months after RARP also had unmeasurable PSA-level 5-8 months after surgery. Limitations are the retrospective design and incomplete follow-up. Conclusions: Patients with an unmeasurable PSA-level at 3-4 months after RARP may not need to be retested until 12 months of follow-up as almost 100% of patients will not have biochemically recurrent disease at 5-8 months of follow-up. This will reduce PSA-testing substantially at the costs of hardly any missed patients with recurrent disease.

Background: With the trend of intelligent display, the interface design of in-vehicle HUD is an expanding research field; Methods: To solve the subjectivity and uncertainty in the optimization of HUD interface design schemes, this paper proposed a hybrid scheme evaluation and optimization method based on entropy weight and VIKOR. The entropy weight method was used to reduce the subjectivity the decision-maker's weighting and obtain the objective weight of each indicator; The VIKOR method was used to obtain the best ranking of alternative schemes, and then the optimal interface design scheme was selected; Results: The evaluation of in-vehicle HUD interface design schemes were taken as an example for verification and calculation. The results showed that this method considers the subjectivity and uncertainty of the decision-making process in the optimization of design scheme, which can effectively improve the objectivity and accuracy of the evaluation results, and provide a reference for designers to optimize interface design schemes.

Electrospinning has gained a lot of attention in recent years due to its ability to easily produce high-quality polymeric nanofibers. However, electrospinning suffers from limited production capacity and a method to readily scale up this process is needed. One obvious approach includes the use of multiple electrospinning needles operating in parallel. Nonetheless, such an implementation has remained elusive, partly due to the uneven electric field distribution resulting from the Coulombic repulsion between the charged jets and needles. In this work, the uniformization of the electric field was performed for a linear array of twenty electrospinning needles using lateral charged plates as auxiliary electrodes. The effect of the auxiliary electrodes was characterized by investigating the semi-vertical angle of the spun jets, as well as the deposition area and diameter of the fibers. Finite element simulation was also used to analyze the impact of the auxiliary electrodes on the electric field intensity below each needle. Implementing parallel lateral plates as auxiliary electrodes was shown to help achieve uniformization of the electric field, the semi-vertical angle of the spun jet, and the deposition area of the fibers for the multi-needle electrospinning process. The high-quality morphology of the polymer nanofibers obtained by this improved process was confirmed by scanning electron microscopy (SEM). These findings help resolve one of the primary challenges that have plagued the large-scale industrial adoption of this exciting polymer processing technique.

The present decade has witnessed numerous investigations focussed on the determination of the mechanical properties of Fly ash composites. These composites have attracted attention, especially in the form of reinforcements owing to their excellent tensile and compressive properties coupled with impact and hardness response. A number of techniques viz. in-situ deposition, hand-up lay and compo-casting techniques have been reported to fabricate these composites. However, in the context of these composites, a systematic structure-property correlation has not been established till date. The present review is aimed at highlighting the current state of research in the avenue of Fly ash composites from two different viewpoints, viz. (i) fabrication technique and (ii) mechanical properties of the fabricated composites. Moreover, the necessity of establishing systematic structure-property correlation in these materials has also been briefly discussed from the author’s viewpoint.

Background: Sickle cell disease (SCD) is a public health problem in the Democratic Republic of Congo. While reference sickle cell centers have been implemented in capital cities of African countries and have proven to be beneficial for SCD patients, they have never been set up in rural areas for families with very low sources of income. Method: A cohort of 143 children with SCD aged 10 years old (IQR (interquartile range): 6–15 years) (sex ratio male/female = 1.3) were clinically followed for 12 months without any specific intervention aside from the management of acute events, and then for 12 months with a monthly medical visit, biological follow-up, and regular prophylaxis. Results: The median age of patients at the diagnosis of SCD was 2 years (IQR: 1–5). The implementation of standardized and regular follow-ups in a new sickle cell referral center in a remote city showed an increase in the annual mean hemoglobin level from 50 to 70 g/L (p = 0.001), and a decrease in the lymphocyte count and spleen size (p < 0.001). A significant decrease (p < 0.001) in the average annual number of hospitalizations and episodes of vaso-occlusive crises, blood transfusions, infections, and acute chest syndromes were also observed. Conclusions: Creation of a sickle cell referral center and the regular follow-up of children with SCD are possible and applicable in the context of a remote city of an African country and represent simple and accessible measures that can reduce the morbimortality of children with sickle cell disease.

Artificial Intelligence is dominated by Artificial Neural Networks (ANNs). Currently, the Batch Gradient Descent (BGD) is the only solution to train ANN weights when dealing with large datasets. In this article, a modification to the BGD is proposed which significantly reduces the training time and improves the convergence. The modification, called Instance Eliminating Back Propagation (IEBP), eliminates correctly-predicted-instances from the Back Propagation. The speedup is due to the elimination of unnecessary matrix multiplication operations from the Back Propagation. The proposed modification does not add any training hyperparameter to the existing ones and reduces the memory consumption during the training.

Liquid biopsy, based on the circulating tumor cells (CTCs) and cell-free nucleic acids has potential applications at multiple points throughout the natural course of cancer, from diagnosis to follow-up. The advantages of doing ctDNA assessment vs. tissue-based genomic profile are the minimal procedural risk, the possibility to serial testing in order to monitor disease-relapse and response to therapy over time and to reduce hospitalization costs during the entire process. However some critical issues related to ctDNA assays should be taken in consideration. The sensitivity of ctDNA assays depends on the assessment technique and genetic platforms used, on tumor-organ, stage, tumor heterogeneity, tumor clonality. The specificity is usually very high, whereas the concordance with tumor-based biopsy is generally low. In patients with renal cell carcinoma (RCC) qualitative analyses of ctDNA have been performed with interesting results regarding selective pressure from therapy, therapeutic resistance, exceptional treatment response to everolimus and mutations associated with aggressive behavior. Quantitative analyses showed variations of cfDNA levels at different tumor stage. Compared to CTC assay, ctDNA is more stable than cells and easier to isolate. Splice variants, information at single-cell level and functional assays along with proteomics, transcriptomics and metabolomics studies can be performed only in CTCs.

Fossil fuels and carbon origin resources are affecting our environment. Therefore, alternative energy sources have to be established to co-produce energy along with fossil fuels and carbon origin resources until it is the right time to replace them. Microbial Fuel Cell (MFC) is a promising technology in the field of energy production. Compared to the conventional power sources it is more efficient and not controlled by the Carnot cycle. Its high efficiencies, low noise, and less pollutant output could make it revolutionize in the power generation industry with a shift from centrally located generating stations and long-distance transmission lines to dispersed power generation at load sites. In this review, several characteristics of the MFC technology will be highlighted. First, a brief history of abiotic to biological fuel cells and subsequently, microbial fuel cells is presented. Second, the focus is then shifted to elements responsible for the making MFC working with efficiency. Setup of the MFC system for every element and their assembly is then introduced, followed by an explanation of the working machinery principle. Finally, microbial fuel cell designs and types of main configurations used are presented along with scalability of the technology for the proper application.

The rapid urbanization that takes place in developing regions such as Sub-Saharan Africa is associated with a large range of environmental and social issues. In this context, remote sensing is essential to provide accurate and up-to-date spatial information to support risk assessment and decision making. However, mapping urban areas remains a challenge because of their heterogeneity, especially in developing regions where the highest rates of misclassification are observed. Nevertheless, urban areas located in arid climates --- which are among the most vulnerables to anthropogenic impacts, suffer from the spectral confusion occurring between built-up and bare soil areas when using optical imagery. Today, the increasing availability of satellite imagery from multiple sensors allow to tackle the aforementioned issues by combining optical data with Synthetic Aperture Radar (SAR). In this paper, we assess the complementarity of the Landsat 8 and Sentinel-1 sensors to map built-up areas in twelve Sub-Saharan African urban areas, using a pixel-level supervised classification based on the Random Forest classifier. We make use of textural information extracted from SAR backscattering data in order to reduce the speckle noise and to introduce contextual information at the pixel level. Results suggest that combining both optical and SAR features consistently improves classification performances, mainly by enhancing the differentiation between built-up and bare lands. However, the fusion was less beneficial in mountainous case studies, suggesting that including features derived from a Digital Elevation Model (DEM) could improve the reliability of the proposed approach. As suggested by previous studies, combining features computed from both VV and VH polarizations consistently led to better classification performances. On the contrary, introducing textures computed from different spatial scales did not improve the classification performances.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Layered double hydroxides (LDHs) have emerged as promising catalysts for various acid-base catalytic reactions. Due to their unique structure and regulatable dual acid-base properties, they offer more environmentally friendly and sustainable alternatives to traditional liquid acid and base catalysts. This study introduces the structural composition, preparation methods, and acid-base catalytic properties of LDHs-based catalysts. Recent application progress of LDHs and rehydrated LDHs, LDHs-based metal nanocatalysts, and LDHs-based mixed metal oxide catalysts used as solid acid-base catalysts in acid-base green catalytic conversion is reviewed. The challenges and prospects of LDHs-based catalysts as green and sustainable catalysts are summarized and proposed.

This article conceptualises the link between firms’ value chains and distribution networks and the requirements for double materiality assessments in contemporary reporting regulations worldwide. The new European Sustainability Reporting Standards (ESRS) and the standards for sustainability reporting issued by the International Sustainability Standards Board (ISSB), called IFRS S1 and IFRS S2, require companies to report their own direct (scope 1) and indirect (scope 2) greenhouse gas (GHG) emissions as well as GHG emissions in their value chains and distribution networks (both scope 3). However, GHG emissions comprise just one dimension of information that is relevant to understand when assessing, managing and reporting the footprints and impacts of a firm and are, therefore, only a fraction of the key performance indicators (KPIs) related to ESG that should be disclosed. Through a case study, this article demonstrates the connection between the due diligence analysis of firms’ value chains and distribution networks, the analysis of the competitive parameters of the business model, the identified impacts, risks and opportunities, and the double materiality perspective. The double materiality perspective prioritises actions based on probability and significance, creating a natural space to identify KPIs. The article concludes by applying the REGS model and illustrating how it can assist firms in identifying relevant KPIs based on double-materiality assessments.

The extent of single and multi-cropping systems in any region, and potential changes to it, have consequences on food and resource use raising important policy questions. However, addressing these questions is limited by a lack of reliable data on multi-cropping practices at a high spatial resolution, especially in areas with high crop diversity. In this paper, we describe a relatively low-cost and scalable method to identify double cropping at the field-scale using satellite (Landsat) imagery. The process combines machine learning methods with expert labeling. We demonstrate the process by measuring double cropping extent in a portion of Washington State in the Pacific Northwest United States--- a region with significant production of more than 60 distinct types of crops including hay, fruits, vegetables, and grains in irrigated settings. Our results indicate that the current state-of-the-art methods for identifying cropping intensity---that apply rule-based thresholds on vegetation indices---do not work well in regions with high-crop-diversity. Our deep learning model was able to capture the diverse nuances and achieve a high accuracy (99\% overall accuracy and 0.92 Kappa coefficient). Our expert labeling process worked well and has potential as a relatively low-cost, scalable approach for remote sensing applications. The product developed here is valuable to inform several policy questions related to food production and resource use.

This study investigates via Lie symmetry analysis the Hunter-Saxton equation, an equation relevant to the theoretical analysis of nematic liquid crystals. We employ the multiplier method to obtain conservation laws of the equation derived from first-order multipliers. Conservation laws of the Hunter-Saxton equation, in combination with the Lie point symmetries of the equation, enable us to perform symmetry reductions through employment of the double reduction method. The method exploits the relationship between Lie point symmetries and conservation laws to effectively reduce both the number of variables and the order of the equation. Five nontrivial conservation laws of the Hunter-Saxton equation are derived, four of which are found to have associated Lie point symmetries. Applying the double reduction method to the Hunter-Saxton equation results in a set of first-order ordinary differential equations, the solutions of which represent invariant solutions for the equation.

In order to solve the interference of narrowband in the ultra-wideband (UWB) system, a high isolation of multiple-input multiple-output (MIMO) antenna is investigated in this paper. The MIMO antenna consists of 2 or 4 UWB elements; and each UWB antenna element is a monopole reconstructed with 2-notched slots, a U-shaped and inverted U-shaped slots etched on the monopole patch to achieve notch characteristics in WIMAX and ITU bands. The property of a 2-element MIMO antenna is analyzed firstly, which is put into a same substrate in parallel. Two rectangular branches are located in the middle to reduce the coupling. Then a 4-element MIMO antenna is studied to meet big size space and more application scenarios. Each element is placed orthogonally on the same substrate; and the isolation is implemented by a cross-shaped branch located in the middle of elements. Both MIMO antenna samples have been tested to verify the design. Measured results show that the working bandwidth is 2.45-14.88 GHz and 2.14-14.95 GHz, the isolation is greater than 17 dB and 20 dB, the peak gain is 5.7 dB and 5.9 dB, the max-imum radiation efficiency can reach 96% and 95%, the envelope correlation coefficient is less than 0.02 and 0.05 for the 2- and 4-element UWB MIMO antenna, respectively. They both are with very good omnidirectional characteristic with notched bands such as the WIMAX and ITU, and meet the requirements of the UWB application in most cases.

Reducing the amount of precipitation in summer in the Chernozems area alters soil organic matter (SOM). To compensate for the lack of moisture, farmers are introducing new agricultural technologies such as no-till cultivation. In turn, no-till practices influence the composition of SOM. We examined the impacts of the rise of aridity and no-till technology on the chemical composition of bioavailable and recalcitrant pools of OM. The properties of SOM were assessed using double-shot pyrolysis with gas chromatography/mass spectrometry (GC/MS). The thermolabile substances that are volatilised in the first stage of pyrolysis (300°C) are considered the bioavailable pool. Accordingly, substances are obtained in the second pyrolysis stage (500°C) were attributed to the recalcitrant pool. Identified in both steps of pyrolysis, products were assigned to different chemical groups (lignin-derivative, polysaccharide-fragments, indoles, etc.) and relative abundances were calculated. In work for the separation of substances, a polar column was used for chromatography of the thermolabile fraction. With an increase in aridity in Сhernozems, the content in the bioavailable pool of polysaccharide fragments decreased and the proportion of indoles increased. In the recalcitrant pool, the abundance of six-membered rings with nitrogen and aromatic compounds decreases at the same time the contents of unsubstituted and O-substituted acyclic compounds as well as pyridine increases. The influence of the NT was more noticeable in the recalcitrant OM. The NT practice promotes biological activity and to rich in nitrogen compounds the bioavailable OM; this process contributes to the accumulation of carbon in the recalcitrant OM.

Due to their short range (2–500 nm), Auger electrons (Auger e-) have the potential to induce nano-scale physiochemical damage to biomolecules. Although DNA is the primary target of Au-ger e-, it remains challenging to maximize the interaction between Auger e- and DNA. To assess the DNA-damaging effect of Auger e- released as close as possible to DNA without chemical damage, we radio-synthesized no-carrier-added (n.c.a.) [189, 191Pt]cisplatin and evaluated both its in vitro properties and DNA-damaging effect. Cellular uptake, intracellular distribution, and DNA binding were investigated, and DNA double-strand breaks (DSBs) were evaluated by im-munofluorescence staining of γH2AX and gel electrophoresis of plasmid DNA. Approximately 20% of intracellular radio-Pt was in a nucleus, and about 2% of intra-nucleus radio-Pt bound to DNA, although uptake of n.c.a. radio-cisplatin was low (0.6% incubated dose after 25-h incuba-tion), resulting in the frequency of cells with γH2AX foci was low (1%). Nevertheless, some cells treated with radio-cisplatin had γH2AX aggregates unlike non-radioactive cisplatin. These findings suggest n.c.a. radio-cisplatin binding to DNA causes severe DSBs by release of Auger e- very close to DNA without chemical damage by carriers. Efficient radio-drug delivery to DNA is necessary for successful clinical application of Auger e-.

Searching for neutrinoless double beta decay is a top priority in particle and astroparticle physics, being the most sensitive test of lepton number violation and the only suitable process to probe the Majorana nature of neutrinos. In order to increase the experimental sensitivity for this particular search, ton-scale detectors operated at nearly zero-background conditions with a few keV energy resolution are required. In this scenario, cryogenic detectors have proven effective in addressing many of these issues simultaneously. After long technical developments, the CUORE experiment established the possibility to operate large scale detectors based on this technology. Parallel studies pointed out that scintillating cryogenic detectors represent a suitable upgrade for the CUORE design, directed towards higher sensitivities. In this work, we review the recent development of cryogenic detectors, starting from the status of the art and outlying the path toward next-generation experiments.

A fully analytical treatment of the base-pair and codon dynamics in double-stranded DNA molecules is introduced, by means of a realistic treatment which considers different mass values for G, A, T, and C nucleotides and takes into account the intrinsic three-dimensional, helicoidal geometry of DNA in terms of a Hamitonian in cylindrical coordinates. Within the framework of the Peyrard-Dauxois-Bishop model we consider the coupling between stretching and stacking radial oscillations as well as the twisting motion of each base pair around the helix axis. By comparing the linearized dynamical equations for the angular and radial variables when going from the bp local scale to the longer triplet codon scale, we report an underlying hierarchical symmetry. The existence of synchronized collective oscillations of the base-pairs and their related codon triplet units are disclosed from the study of their coupled dynamical equations. The possible biological role of these correlated, long-range oscillation effects in double standed DNA molecules containing mirror-symmetric codons of the form XXX, XX’X, X’XX’, YXY, and XYX is discussed in terms of the dynamical equations solutions and their related dispersion relations.

This study used double-bounded dichotomous-choice to estimate and analyze the factors affecting households’ willingness to pay (WTP) for water quality improvement. This study notes that households with higher income, living near polluted water source, using tap water instead of natural water, who are handicraft producers, and who have more members are willing to pay more. However, households who rarely hear about environmental pollution issues and who are offered a higher bid are more likely to refuse to pay. Solutions to improve water quality are suggested such as to raise people's awareness through communication channels and social organizations; to increase income associated with environmental protection policies; to construct wastewater treatment plants; to encourage the relocation of production establishments to industrial parks and industrial complexes; to put regulations on collection, payment and sanctions in case of not declaring and paying fees into village conventions; to promulgate circulars, and bylaws to concretize and simplify regulations and policies of the Government, Ministry of Natural Resources and Environment.

: Background: Overweight and obesity are major risk factors for many chronic diseases, and weight-loss interventions often include systematic exercising and nutritional supplements. The purpose of this study was to determine the independent/synergistic effects of Spirulina maxima supplementation (6-week, 4.5 g/day) and a systematic physical exercise program (6 weeks/ 2 times) on body composition and cardiorespiratory fitness of overweight and obese subjects. Methods: 27 overweight and 25 obese sedentary male subjects were assigned to four interventions through a randomized double-blind, crossover controlled trial: Physical exercise program with (SE) or without (Ex) Spirulina maxima or no-exercise program with (Sm) and without (C) Spirulina maxima. Body composition and cardiorespiratory fitness parameters were taken during a maximal intensity test. Results: As compared to C group, SE, Sm and Ex groups reduced (p < 0.05) their body fat percentage while improving their maximal oxygen uptake (VO₂max; r = −0.40), being obese subjects more benefited. Weight loss, time to reach fatigue and onset of blood lactate accumulation were improved in both Spirulina maxima supplemented groups, regardless the subjects’ body composition. Conclusions: Spirulina maxima supplementation synergistically improves the effects of systematic exercise in body composition and cardiorespiratory fitness parameters in overweight but mostly in obese adults.

Concrete is a very common construction material. As time prevails, cracks often appear in structures that pose a threat to strength and durability, which ultimately affect the structural integrity of concrete. Extensive work has been carried out in past on utilization of Carbon Fiber Reinforced Polymer (CFRP) as a repair material. But, this research particularly focuses on: multiple fiber layers i.e. single and double, traditional concrete mix ratio with locally available materials and varying flexural reinforcement. Furthermore, this work presents an experimental analysis to strengthen the Reinforced Concrete (RC) beams using SikaWrap- 230 C as a CFRP wrap, and Sikadur-330 as a bonding material. The comparison between single and double layers of CFRP is of major interest in this research. Six reinforced concrete beams were repaired with CFRP and tested under three-point bending test. For these specimens, load deflection behavior along with crack propagation and failure of beams were studied. Experimental results show that beams repaired using CFRP wrapping achieved higher flexural capacity and ductility as compared with reference beam. Moreover, results reveal that introduction of second layer of fiber caused around 4-5.2% increment in flexural strength and resulted in higher ductility of RCC beam.

Fracture density, a critical parameter of unconventional reservoirs, can be used to evaluate potential of unconventional reservoirs and location of production wells. Many technologies, such as amplitude variation with offset and azimuth (AVOA) technology, vertical seismic profiling (VSP) technology, and multicomponent seismic technology, are generally used to predict fracture of reservoirs. they can qualitatively predict fracture by analyzing seismic attributes, including seismic wave amplitudes, seismic wave velocities, which are sensitive to fracture. However, it is important to quantitatively describe fracture of reservoirs. In this study, based on a double-layer model, the relationships between fracture density and the double-layer model’s physical parameters, such as velocity of fast shear-wave, velocity of slow shear-wave, and density, were established, and then a powerful quantitative prediction method for fracture density was proposed dramatically. Afterwards, the Hudson model for crack was used to test the applicability of the method. The result shown that the quantitative prediction method for fracture density can be applied suitable to the Hudson model for crack. Finally, the result of validation models indicated that the method can predict fracture density effective, in which absolute relative deviation (ARD) were less than 5% and root-mean-square error (RMSE) was 4.88×10-3.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

Plasmonic nanomaterials have garnered considerable attention in the scientific community due to their applicability in light-mediated technologies, owing to tunability, large light absorption cross-sections, transparency, and potential scalability. While single morphology plasmonic nanoparticles exhibit substantial absorption cross-sections, their effectiveness is limited to a narrow energy window, especially under polychromatic illumination like sunlight. Integrating plasmonics with a Fabry-Pérot nanocavity is a promising approach to broaden the absorption energy range of the photosystem. Traditionally, the fabrication of these nanocavities involves clean room processes, posing scalability challenges. This study presents a novel approach, demonstrating the successful enhancement of light absorption in a plasmonic photoelectrode system through a Fabry-Pérot nanocavity created using bottom-up solution methods. This innovative technique not only overcomes the scalability issues associated with clean room processes but also enables the production of scalable photosystems that can be rendered entirely opaque or semitransparent. Such versatility opens up a multitude of application possibilities for these photosystems.

In this paper we compare the effects of forecasting demand using individual (disaggregated) components versus first aggregating the components either fully or into several clusters. Demand streams are assumed to follow autoregressive moving average (ARMA) processes. Using individual demand streams will always lead to a superior forecast compared to any aggregates, however we show that if several aggregated clusters are formed in a structured manner then these subaggregated clusters will lead to a forecast with minimal increase in mean-squared forecast error. We show this result based on theoretical MSFE obtained directly from the models generating the clusters as well as estimated MSFE obtained directly from simulated demand observations. We suggest a pivot-algorithm, that we call Pivot Clustering, to create these clusters. We also provide theoretical results to investigate sub-aggregation, including for special cases such as, aggregating MA(1) streams and ARMA streams with similar or same parameters.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

The clinical significance of carbon-ion radiotherapy (CIRT) for adenocarcinoma (AC) of the uterine cervix has been assessed in several single-institutional studies. To validate the significance, we conducted a multi-institutional survey of CIRT for locally advanced AC (LAAC) of the uterine cervix. We retrospectively analyzed the clinical outcomes of patients with stage IIB–IVA LAAC of the uterine cervix who underwent chemo-CIRT or CIRT alone between April 2010 and April 2016. Patients received 74.4 Gy (relative biological effectiveness [RBE]) in 20 fractions of CIRT or 55.2 Gy (RBE) in 16 fractions of CIRT plus 3 sessions of brachytherapy. Patients aged ≤70 years with adequate bone marrow and organ function were administered cisplatin weekly (40 mg/m2 per week for up to 5 weeks). Fifty-five patients were enrolled in this study. The median follow-up period was 67.5 months. The 5-year overall survival (OS) and local control (LC) rates were 68.6% and 65.2%, respectively. Multivariate analysis showed that the initial tumor response within 6 months was significantly associated with LC and OS. The present study represents promising outcomes of CIRT or chemo-CIRT for LAAC of the uterine cervix, especially in the cases showing initial rapid regression of the tumor.

Scientists who are interested in building research programs at primarily-undergraduate institutions (PUIs) have unique considerations compared to colleagues at research-intensive (R1) institutions. Maintaining a research program at a PUI holds unique challenges that should be considered before prospective faculty go on the job market, as they negotiate a job offer, and after they begin a new position. In this article we describe some of the considerations that aspiring and newly hired faculty should keep in mind as they plan out how they will set up a laboratory as a new Principle Investigator (PI) at a PUI. Anyone hoping to start a research program at a PUI should understand both the timeframe of interviews, job offers, and negotiations and the challenges and rewards of working with undergraduate researchers. Once a job is offered, candidates should be aware of the range of negotiable terms that can be part of a start-up package. Space and equipment considerations are also important, and making the most of shared spaces, existing infrastructure, and deals can extend the purchasing power of start-up funds as a new PIs builds their lab. PUIs’ focus on undergraduate education and mentorship leads to important opportunities for collaboration, funding, and bringing research projects directly into undergraduate teaching laboratories. A major focus of any new laboratory leader must be on building a productive, equitable, and supportive laboratory community. Equitable onboarding, mentorship plans, and formalized expectations, can all help build a productive and sustainable laboratory research program. However, important considerations about safety, inclusion, student schedules, and a PI’s own professional commitments are also extremely important concerns when working with undergraduates in research. A successful research program at a PUI will bring students into meaningful scientific inquiry and requires insights and skills that are often not the focus of scientific training. This article aims to describe the scope of setting up a new laboratory as a way to alleviate some of the burden that new and prospective faculty often feel.

Detailed built-up area information is valuable for mapping complex urban environments. Although a large number of classification algorithms about built-up areas have been developed, they are rarely tested from the perspective of feature engineering and feature learning. Therefore we launched a unique investigation to provide a full test of the OLI imagery for 15-m resolution built-up area classification in 2015, in Beijing, China. Training a classifier requires many sample points, and we propose a method based on the ESA's 38-meter global built-up area data of 2014, Open Street Map and MOD13Q1-NDVI to achieve rapid and automatic generation of a large number of sample points. Our aim is to examine the influence of a single pixel and image patch under traditional feature engineering and modern feature learning strategies. In feature engineering, we consider spectra, shape and texture as the input features, and SVM, random forest (RF) and AdaBoost as the classification algorithms. In feature learning, the convolution neural network (CNN) is used as the classification algorithm. In total, 26 built-up land cover maps were produced. Experimental results show that: (1) the approaches based on feature learning are generally better than those based on feature engineering in terms of classification accuracy, and the performance of ensemble classifiers e.g., RF, is comparable to that of CNN. Two dimensional CNN and the 7 neighborhood RF have the highest classification accuracy of nearly 91%. (2) Overall, the classification effect and accuracy based on image patches are better than those based on single pixels. The features that can highlight the information of the target category (for example, PanTex and EMBI) can help improve classification accuracy.

Digital infrastructure is the basic guarantee for digital transformation, it is of practical significance to discuss how to effectively use digital infrastructure construction to promote the digital transformation of tourism enterprises. This paper examines the impact of digital infrastructure construction on tourism enterprises based on the "Broadband China" policy as a quasi-natural experiment. A-share tourism listed enterprises from 2010 to 2021 are studied using the double difference method. Findings indicate that digital infrastructure construction positively and significantly influences the digital transformation of tourism enterprises, driven by digital leadership and innovation capabilities. State-owned, small-scale, and high-growth tourism enterprises benefit more from this transformation. The results suggested that the state should develop differentiated digital infrastructure plans based on the specific conditions of different tourism enterprises. Additionally, tourism enterprises should enhance digital leadership and innovation capabilities through strategic changes and digital applications to amplify the impact of digital infrastructure on their transformation.

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

Based on the elasticity theory, this paper deals with the static analysis of a cracked double beam system in presence of a Winkler medium. The double-beam system is also supposed to be constrained at both ends by elastically flexible springs, with transverse and rotational stiffness. Using a variational formulation, the static governing equations are derived and solved by using analytical and numerical approaches. In the first approach, the closed-form solutions for the displacements functions are obtained based on the Euler-Bernoulli beam theory. In the second approach, the Cell-Discretization Method (CDM) is performed, according to which the two beams are reduced to a set of rigid bars linked together by means of elastic constraints, where the bending stiffness of the bars is concentrated. The resulting stiffness matrix is easily deduced, and the governing equations of the static problem can be immediately solved. A comparative analysis is performed in order to verify the accuracy and validity of the proposed method. This study focuses on the effect of various parameters including the crack depth and position, boundary conditions, elastic medium and slenderness. The validity of the proposed analysis is confirmed by comparing the present results with those obtained from the other approach. In particular, the results obtained by closed-form solution and Cell-discretization method (CDM) are compared by Finite element method (FEM). Accuracy of the results has been evaluated by making comparisons with the results in literature and reported in bibliography. It is demonstrated that the proposed algorithm provides a simple and powerful tool in dealing with the static analysis of a double-beam system. Finally, some concluding remarks are made.

When using meta-heuristic optimization approaches for optimization, a large number of samples are required. In particular, when generating subgeneration, the utilization of existing samples is low and the number of individuals is high. Therefore, surrogate-based optimization has been developed, which greatly reduces the number of individuals in the subgeneration and the cost of optimization. In complex air supply scenarios, single-objective optimization results may not be comprehensive; therefore, this paper developed a double-objective air supply optimization method based on the Kriging surrogate model and Non-dominated Sorting Genetic Algorithms-II. And proposed the infill criteria based on clustering to advance the Pareto Frontier. The method was validated by an inverse prediction case, and in particular, the problems when based on 3D steady-state simulations were analyzed. The results showed that the method can quickly achieve an approximate prediction of the boundary conditions (when prediction were made based on experimental data, the number of simulations was 82 and the average error was 6.8%). Finally, the method was used to optimize the air supply parameters of a dual-aisle, single-row cabin. The Pareto set suggested that an airflow organization with dual circulation may be optimal.

Diffusion-controlled cyclic voltammograms at fast scan rates show peak shifts as well as decreases in the peak currents from the predicted diffusion-controlled currents especially when currents are large in low concentration of supporting electrolyte. This has been conventionally recognized as an IR-drop effect by solution resistance on the peaks as well as heterogeneous kinetics. It is also brought about by negatively capacitive currents associated with charge transfer reactions. The reaction product generates dipoles with counterions to yield a capacitance, of which current flows oppositely to that of the double layer capacitance. The three effects are specified here in the oxidation of a ferrocenyl derivative by fast scan voltammetry. The expression for voltammograms complicated with IR-drop is derived analytically, and yields deformed voltammograms. The peak shift is approximately linear with the IR-term, but exhibits a convex variation. Dependence of some parameters on the peaks by the IR-drop is compared with those by the negative capacitance. The latter is more conspicuous than the former under conventional conditions. The two effects cannot be distinguished specifically except for variations of conductance of the solution.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

As the global aging trend continues to intensify, there will inevitably be more complex and diverse aging problems in the future. There is no doubt that designers have the responsibility to explore the possibilities of the future and solve the problems that will be faced in the future. Based on the Future Cone, the Double Diamond Model and the IDEO Method Cards, this study proposes a new model to guide the design practice of future aging issues in the context of aging. With the aim of validating and refining the framework, an ageing designer workshop was held where participants were asked to imagine, explore and express ideas about future ageing issues. The workshop was used to refine the proposed model. More specifically, the model includes a future concept, a design guidance process based on the Double Diamond Model, and tools that can be applied at all stages of design, which can help designers generate ideas and solutions for future aging problems, and collectively lead society to a more desirable future. Moreover, this study also explores broader directions for the development of the model and provides a reference for continued research on this topic in the future.

Relative contribution of different repair pathways to the radiation-induced DNA damage responses remains a challenging issue of studying the radiation injury endpoints. Comparative manifestation of homologous recombination (HR) after application of different radiation doses greatly determines an overall effectiveness of recovery in dividing cell after irradiation, since HR is an error-free mechanism intended for repair of DNA double strand breaks (DSB) during S/G2 phases of cell cycle. In this article, we present an experimentally observed evidence of dose-dependent shift in relative contribution of HR in human fibroblasts after X-ray exposure at doses 20-1000 mGy, which is also supported by quantitative modeling of DNA DSB repair. Our findings indicate that the radiation dose increase leads to dose-dependent decrease in relative contribution of HR into the entire repair process.

New hybrid composites based on the inclusion of a vegetal extract, i.e., Boswellia Serrata extract (BSE), rich in boswellic acids, well known as a potent anti-inflammatory natural drug, in a lamellar solid layered double hydroxide (LDH), i.e. a Magnesium Aluminum Carbonate, were developed and characterized in the present work. The adopted LDH exhibits a layered crystal structure, comprised of positively charged hydroxide layers and interlayers composed of carbonate anions and water molecules, thus it was expected to embed negatively charged boswellic acids. In the present case, a calcination process was also adopted on LDH to increase organic acids loading, based on the replacement of original inorganic anions. An accurate investigation was carried out by TGA, PXRD, FT-IR/ATR, XPS and LC-MS to ascertain the nature, interaction, and quantifica-tion of the active molecules of the vegetal extract loaded in the developed hybrid materials. As a result, a significant disruption of the original layered structure was observed in LDH subjected to calcination (LDHc), and this material was able to include a higher amount of organic acids when its composite with BSE was prepared. However, in vitro tests on composites bioactivity, expressed in terms of antimicrobial and anti-inflammatory activity, evidenced LDH-BSE as a better material compared to BSE and to LDHc-BSE, thus suggesting that, though the embedded organic acids amount was lower, they could be more available since not firmly bound to the clay. The composite was able to significantly decrease the number of viable pathogens such as Escherichia Coli and Staphylococcus aureus, as well as the internalization of toxic active species into human cells imposed to oxidative stress in comparison to the BSE.

The G-NUMEN array is the future gamma spectrometer of the NUMEN experiment (Nuclear Matrix Element for the Neutrinoless double beta decay), to be installed around the object point of the MAGNEX magnetic spectrometer at the INFN-LNS laboratory.. This project aims at exploring Double Charge Exchange (DCE) reactions in order to obtain crucial information about the neutrinoless double beta decay (0νββ). The primary objective of the G-NUMEN array is to detect the gamma rays emitted from the de-excitation of the excited states populated via DCE reactions with good energy resolution and detection efficiency, amidst a background composed of transitions from competingreaction channels with far higher cross-sections. To achieve this, the G-NUMEN signalswill be processed in coincidence with those generated by the detection of the reaction ejectiles in the MAGNEX Focal Plane Detector(FPD). Under the expected experimental conditions, G-NUMEN detectors will operate at high counting rates, of the order of hundreds of kHz per detector, while maintaining excellent energy and timing resolutions. The complete array will consist of over 100 LaBr3(Ce) scintillators. Initial tests have been conducted on the first detectors of the array, allowing for the determination of their performance at high rates.

Hydrogels, soft materials with 3D polymer networks in aqueous solution, have been developed for engineering and bio-related fields. However, these conventional hydrogels are weak and brittle due to lack of energy dissipation mechanisms. Recently, dual-network hydrogels have been proposed, combining rigid and flexible networks and exhibiting high strength, stretchability, and toughness. This paper explores the rheological properties of dual-network hydrogels based on acrylamide and sodium alginate under large deformations. This dual network is a combination of a covalently crosslinked polyacrylamide network and a supramolecular crosslinked sodium alginate network at the presence of divalent calcium cations. Small and large amplitude oscillatory shear methods with Fourier transform rheology, stress decomposition method, and Chebyshev polynomial analysis of large amplitude oscillatory shear (LAOS) data were employed to evaluate non-linearity limit, toughness, and network rigidity. The concentration of calcium ions affects (concentrations 0-80 mg/ml) the nonlinear transition and limit points, and all gel samples exhibit strain hardening, shear thickening, and shear densification.

The crystal structure of quintinite, Mg4Al2(OH)12(CO3)·3H2O, from Jacupiranga alkaline complex (Cajati, São Paulo, Brazil) has been refined for two samples (91002 and C7029) using single-crystal X-ray diffraction data. The mineral crystallizes in the P-3c1 space group, a = 5.246/5.298, c = 15.110/15.199 Å for the samples 91002/C7029. The crystal structure consists of octahedral sheets with Mg and Al ordering according to the 3 × 3 superstructure. The Mg and Al atoms are coordinated by six hydroxylated oxygen atoms each with the average &lt;Mg–O&gt; and &lt;Al–O&gt; bond distances being in the ranges 2.022–2.053 Å and 1.974–1.978 Å, respectively. The interlayer structures are identical (in contradiction to the previous assumptions) and compose from disordered (CO3)2- groups and (H2O)0 molecules. The samples from Jacupiranga can be identified as quintinite-2T that is the second find of the polytype after the Kovdor alkaline complex (Kola peninsula, Russia). The powder X-ray diffraction pattern of quintinite-2T contains weak superstructure reflection at 4.57 Å (010) indicative of Mg and Al ordering. An important crystal-chemical criterion of quintinite is the interlayer distance (d00n-value) of ~ 7.56 Å, which is steady for natural specimens from various findings worldwide.

Minimal rotating thermodynamic systems are addressed. Particle m placed into the rotating symmetrical double-well potential (bowl), providing binary logical system is considered. The condition providing the transfer of the particle from one frictionless half-well to another, and in this way possibility to record 1 bit of information is derived. The procedure of recording turns out to be irreversible; it is impossible to return the particle to its initial state under rotation about the same axis. The same rotating double-well system exerted to the thermal noise is considered. Minimal rotating thermal engine built of the rotating chamber, movable partition and the particle confined within the chamber is treated. Rotation of the system displaces the partition; thus, enabling erasing of one bit information. Erasing of 1 bit of information is due to the inertia (centrifugal force) acting on the partition. Isothermal expansion of the “minimal gas” expectedly gives rise to the Landauer bound. Compression of the “gas” with the rotation around the same axis is impossible and demands the additional axis of rotation. The interrelation between the possibility of recording/erasing information and the symmetry of the system is considered.

To understand the enhanced protection mechanism of CoCrNiAlY-YSZ-LaMgAl11O19 dou-ble-layer ceramic coating with aluminum plating, a finite element simulation method was used to simulate the distribution of thermal stress in the coating in all directions. The results show that in the air exposure of the un-aluminized coating, high temperature causes a large radial thermal stress on the surface of the LaMgAl11O19 (LMA) layer, and it increases with the increase in temperature, which is the main reason for the initiation of axial cracks. After arc aluminum plating, the aluminum plating layer effectively inhibited the volume shrinkage of the coating through good adhesion to the coating and internal diffusion, the thermal stress of the coating was considerably reduced, and the CoCrNiAlY-YSZ-LMA coating had an effective enhancement and protection effect; however, there was still a certain amount of shear thermal stress inside the LMA layer, the top of the crack, and the bottom of the crack. This thermal stress caused the initi-ation of radial microcracks in the LMA layer, which also becomes a risk point for the failure of the aluminum coating.

Urinary and fecal incontinence as well as skin pressure injury are common healthcare problems in nursing home; however, these prevalence and related risk factors were not well understood in the Japanese special elderly nursing home settings. We surveyed the prevalence of urinary, fecal and double incontinence, and skin pressure injury among the elderly living in special elderly nursing home in Japan. A nationwide cross-sectional epidemiological survey was conducted with a total of 4,881 residents. The prevalence of urinary, fecal and double incontinence was 82.9%, 68.9% and 64.9%, respectively. Skin pressure injury was found in 283 residents (283/4881, 5.8%). Age, Care-Needs level, loss of voiding desire, and fecal incontinence were significant risk factors for urinary incontinence. Residential period, Care-Needs level, loss of voiding and defecation desires, and urinary incontinence were significant risk factors for fecal incontinence. Only male sex was a significant risk factor for skin pressure injury. Our study revealed continence status and the prevalence of pressure skin injury among older adult residents who receive an end-of-life care in special nursing homes in Japan. Further studies should be conducted to examine whether recovery of urinary and fecal sensations improves continence status.

Phytophthora. infestans is a well known late blight causing oomycetes pathogen. It evolves and adapts to the host background and new fungicide molecules rapidly within a few years of their release, may be due to the predominance of transposable elements in its genome. Frequent and huge applications of fungicides cause environmental concerns. Here we developed target specific RNA interference based molecules, that are capable of effectively reducing the late blight infection. cDNA microarray expression data was used for the selection of genes involved in the early stage of infection process, sporulation etc. The in vitro synthesis of double stranded RNA molecule, targeting SDH, EF-1α, GPI-HAM344, PLD-3 and HSP-90 encoding genes revealed the reduction in growth, sporulation and symptom expression, which were subsequently assessed by culture bioassay, detached leaf assay and topical application methods. The multiple genes targeted dsRNA nano clay sprayed plants showed enhanced disease resistance (4% disease severity) and least sporulation (<1x103), compared to naked dsRNA spray. Use of nano clay was assumed to be involved in the effective delivery, protection and boosting the action of RNAi in potato plants. A significant difference in the growth, sporulation count, disease severity and reduced expression of the genes and confocal microscopy imaging authenticates the effects of SIGS on late blight disease progression. Our research demonstrated that topical dsRNA nano clay spray under the open-air environment could be an alternative to chemical fungicides and transgenic approaches as a novel plant protection strategy for late blight in an environmentally friendly manner.

The study explored the contribution of ICT-based information sources to market participation among smallholder livestock farmers. Use of ICTs is considered paramount for providing smallholder farmers with required market information, in order to reduce market asymmetries. A Double Hurdle regression was utilized to analyze data collected from 150 smallholder livestock farmers in the study area. The results show that while use of ICT-based market information sources significantly influenced market participation, the effect of using ICT-based information sources on intensity of market participation was not significant. Other variables shown to influence both market participation and the intensity of market participation were age, additional income and membership of farmer cooperatives. This suggests the need to also consider other associated factors in the application of interventions which utilize ICT-based information sources in achieving planned market interventions.

A double-stranded RNA (dsRNA) virus was isolated and characterized from a strain EW220 of the phytopathogenic fungus Botryosphaeria dothidea. The full-length cDNAs of dsRNAs were 6,434 bp and 5,986 bp in size, respectively. The largest dsRNA of BdBRV1 encodes a cap-pol fusion protein that contains part coat protein gene and a RNA-dependent RNA polymerase (RdRp) domain, and the second dsRNA encodes a hypothetical protein. The dsRNA virus was named Botryosphaeria dothidea botybirnavirus 1 (BdBRV1). BdBRV1 contains spherical virions that are 37 nm in diameter consisting of two segments. The structural proteins of BdBRV1 virus particles were 110 kDa, 90 kDa, and 80 kDa, which encoded by dsRNA1 and 2-ORFs. The analysis of genome sequences revealed that the sequences of BdBRV1 shared 99% identity with Bipolaris maydis botybirnavirus 1(BmBRV1). Phylogenetic reconstruction indicated that BdBRV1 and BmBRV1 are phylogenetically related to the genus Botybirnavirus. Importantly, BdBRV1 influences the growth of B. dothidea and confers hypovirulence to the fungal host. BdBRV1 and BmBRV1 were two strains of the same virus. To our knowledge, this is the first report of a botybirnavirus in B. dothidea and our result might be the first funding in the different fungi infected by the same virus.

The most important prognostic factors in curatively treated prostate cancer at the initial diagnosis are T and N stage, histological subtype, Gleason score, initial PSA, PSA density and percentage of core biopsy positivity. Newer, but non-standard prognostic factors are urine PCA3 and genetic markers of prostate cancer. A simple, but seemingly underestimated standard test is serum Calcium (Ca) level, which has been shown by a previous study group to be a good predictor of lethal prostate cancer, but there is scarce evidence regarding the prognostic value of calcium levels at diagnosis. We aimed to determine whether a Ca level in the upper part of normal values has a prognostic value in curatively treated prostate cancer. We have retrospectively included 84 consecutive patients with prostate cancer, who underwent curative radiotherapy (primary or adjuvant; external beam RT with or without brachytherapy). We have performed statistical analysis of available prognostic factors. Ca level at diagnosis was found to be a statistically significant predictor of disease-free survival.

Reservoir in the Central Structural Zone of the Xihu Sag is the Huagang Formation, dominated by natural gas reservoirs, and the reservoir in the Western Slope Zone is the Pinghu Formation, dominated by light oil and wet gas. In this paper, the Gas Drive Water Displacement- Magnetic Resonance Imaging (GWD-MRI) experiments are used to simulate the charging characteristics of the sandstone migration layer. The centrifugal- Magnetic Resonance (Cen-NMR) experiments simulate the short-term fast trap charging process, and the Semi-Permeable Baffle (SPB) charging experiment simulates the slow trap accumulation process. Studies have shown that there is a start-up pressure for the migration layer charging, and the start-up pressure of the core with a permeability of 0.3mD is about 0.6MPa. Experimental simulations have confirmed that there is a front zone with changed water saturation, with a width of about 1-1.5cm. The migration layer charging mainly has two actions, drive effect and carry effect. The drive effect reduces the water saturation to 70%-80%, and the carry effect can still reduce the water saturation by 5%-10%. The water saturation of rapid charging is mainly affected by the petro-physical. The porosity is high, the water saturation is low. The water saturation decreased significantly with the increase of centrifugal force when the centrifugal force is smaller. If the centrifugal force is greater than 0.8 MPa, the water saturation decreases slowly. The water saturation of the trap slowly charging is basically maintained at 40%-50%, which matches the water saturation of the airtight coring from 40%-55%, the petro-physical do not affect the final water saturation.

Temporary pavilions play an important role as experimental fields for architects, designers and engineers, apart from providing exhibition spaces. Novel structural and formal solutions applied in pavilions also can give them unusual appearance that attracts eyesight of spectators. In this article authors explore the possibility of combination of structural novelty, visual attractiveness and low-cost by a design and construction of a temporary pavilion. For that purpose, an innovative structural system and design approach was applied, i.e. membrane structure designed in Rhino and Grasshopper environments with the use of Kiwi!3D IsoGeometric analysis tool. The designed pavilion, named Obverse/Reverse, was built in Opole, Poland, for the occasion of World Architecture Day in July 2019. Design and construction was performed by the authors in cooperation with students’ organisation Humanisation of Urban Environment from the Faculty of Architecture Wroclaw University of Science and Technology. The Rresultant pavilion proved the possibility of obtaining a low-budgets but visually attractive architectural solution with the adaption of parametrical design tools and some scientific background with innovative structural systems.

Nanoprecipitation by liquid anti-solvent precipitation is one of the most versatile methods to produce pure drug nanoparticles (PDNPs) owing to the ability to optimize the properties of the product. Nevertheless, nanoprecipitation shows broad particle size distribution and low physical stability, leading to high batch-to-batch variability and challenging the bench-to-bedside translation. Microfluidics has emerged as a powerful tool to produce PDNPs in a simple, reproducible, and cost-effective manner with excellent control over NP size. In this work, we designed and fabricated T- and Y-shaped Si-made microfluidics device and used it to produce pure NPs of three kinase inhibitors of different lipophilicity and water-solubility, namely imatinib, dasatinib and tofacitinib, without the use of colloidal stabilizers. PDNPs display sizes in the 90-350 nm range (dynamic light scattering) and a rounded shape (high-resolution scanning electron microscopy). Analysis by X-rays diffraction and differential scanning calorimetry confirmed that this method results in highly amorphous NPs. In addition, we show that the flow rate of solvent, the anti-solvent, and the channel geometry of the device play a key role in the size of the generated NPs.

Sedation is a ubiquitous practice in ICUs and NCCUs. It has the benefit of reducing cerebral energy demands, but also precludes an accurate neurologic assessment. Because of this, sedation is intermittently stopped for the purposes of a neurologic assessment, which is termed a neurologic wake-up test (NWT). NWTs are considered to be the gold-standard in continued assessment of brain-injured patients under sedation. NWTs also produce an acute stress response that is accompanied by elevations in blood pressure, respiratory rate, heart rate, and ICP. Utilization of cerebral microdialysis and brain tissue oxygen monitoring indicates that this is not mirrored by alterations in overall cerebral metabolism, and seldom affects oxygenation. The hard contraindications for the NWT are preexisting intracranial hypertension, barbiturate treatment, status epilepticus, and hyperthermia. However, hemodynamic instability, sedative use for primary ICP control, and sedative use for severe agitation or respiratory distress are considered significant safety concerns. Despite ubiquitous recommendation, it is not clear if additional clinically relevant information is gleaned through its use, especially with the contemporaneous utilization of multimodality monitoring. Various monitoring modalities provide unique and pertinent information about neurologic function, however, their role in improving patient outcomes and guiding treatment plans has not been fully elucidated. There is a paucity of information pertaining to the optimal frequency of NWTs, and if it differs based on type of injury. Only one concrete recommendation was found in the literature, exemplifying the uncertainty surrounding its utility. The most common sedative used and recommended is propofol because of its rapid onset, short duration, and reduction of cerebral energy requirements. Dexmedetomidine may be employed to facilitate serial NWTs, and should always be used in the non-intubated patient or if propofol infusion syndrome (PRIS) develops. Midazolam is not recommended due to tissue accumulation and residual sedation confounding a reliable NWT. Thus, NWTs are well tolerated in most patients and remain recommended as the gold-standard for continued neuromonitoring. Predicated upon one expert panel, they should be performed at least one time per day. Propofol or dexmedetomidine are the main sedative choices, both enabling a rapid awakening and consistent NWT.

Replacement of fee-for-service with capitation arrangements, forces physicians and institutions to minimize health care costs, while maintaining high-quality care. In this report we describe how patients, their families (and caregivers) can work with members of the medical care team to achieve these twin goals of maintaining (and perhaps improving) high-quality care and minimizing costs. We describe how increased self-management enables patients and their families/caregivers to provide electronic patient-reported outcomes (i.e., symptoms, events) (ePROs) as frequently as the patient or the medical care team consider appropriate. These capabilities also allow greater reliance on the use of mobile technologies (mHealth) to provide ongoing assessments of physiologic measurements/phenomena. Remote surveillance of these communications allows longer intervals between (fewer) visits of patients to the medical-care team when this is appropriate and earlier interventions when that is appropriate. Systems are now available that alert medical care providers to situations when interventions might be needed.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

The Double Random Phase Encoding (DRPE) image encryption method has garnered significant attention in color image processing and optical encryption, thanks to its parallel encryption of R, G, B. However, DRPE-based color image encryption faces two challenges. Firstly, it disregards the correlation of R, G, and B, compromising the encrypted image's robustness. Secondly, DRPE schemes relying on Discrete Fourier Transform (DFT) and Discrete Fractional Fourier Transform (DFRFT) are vulnerable to linear attacks, such as Known Plaintext Attack (KPA) and Chosen Plaintext Attack (CPA). Quantum walk stands out as a remarkable tool for designing modern cryptographic mechanisms, offering resistance to potential attacks from both classical and quantum computers.Therefore, this study presents an optical color image encryption algorithm that combines two-dimensional quantum walk with 24-bit plane permutation, dubbed OCT. This approach employs pseudo-random numbers generated by Two-Dimensional Quantum Walking (TDQW) for phase modulation in DRPE and scrambles the encrypted image's real and imaginary parts using the Generalized Arnold Transform. The 24-bit plane permutation helps reduce correlation of the R, G, B, while the Generalized Arnold Transform bolsters DRPE's resistance to linear attacks. By incorporating TDQW, the key space is significantly expanded. Experimental results validate the effectiveness and security of proposed method.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Light can interfere like a wave in a multi-path experiment, but it also has particle properties when interacting with matter. In a closer look, the interference pattern is created by many individual detections ("clicks"), which do not all occur simultaneously. An established assumption is therefore that a single light particle is capable of interfering with itself by superimposing all possibilities to get from the source to the detector. This is in stark contrast to our experience with macroscopic objects, which always "decide" in favour of only one of the alternative paths.In 2010, Jin et al. (Ref. 15) described an event-based model which allowed the authors to show that an interference pattern consisting of clicks can arise in a multi-path experiment even if photons, like macroscopic objects, only follow one path. To do this, photons must be able to transmit the information about their travelling duration to the detector and the detector must have a basic memory. A threshold function uses the message of several light quanta to decide whether a single detection is initiated, which is not the evidence for a single photon. In this "proof of principle", the authors do not claim that the detector function is a realistic one.In the present paper, this detector is replaced by a material consisting of ionizable molecules whose interaction with light takes place according to a modified version of Einstein's radiation laws. Based on this, a photon pair interaction mediated by matter takes place, which in a multi-path experiment generates an interference pattern of clicks at the detector, even if an arbitrary amount of time elapses between the individual detections. In the present model an interference pattern with minima that have less than half the intensity of the maxima is the result of a peculiar behaviour of the detector: In this case, the entirety of its electrons must be described as a unit (a “field”) with many equidistant energy levels. The results of a simulation are presented which enable the model to be tested in experiments.

Shape-shifting polymers usually require not only reversible stimuli-responsive ability, but also strong mechanical properties. A novel shape-shifting photochromic hydrogel system was designed and fabricated through embedding hydrophobic spiropyran (SP) into double polymeric network (DN) by micellar copolymerization. Here, sodium alginate (Alg) and poly acrylate-co-methyl acrylate-co-spiropyran (P(SA-co-MA-co-SPMA)) were employed as the first network and the second network respectively to realize high mechanical strength. After soaked in the CaCl2 solution, the carboxyl groups in the system undergo metal complexation with Ca2+ to enhance the hydrogel. Moreover, after the hydrogel is exposed to UV-light, the closed isomer of spiropyran in the hydrogel network can be converted into an open zwitterionic isomer MC, which is considered to interact with Ca2+ ions. Interestingly, Ca2+ and UV-light responsive programmable shape of the copolymer hydrogel can recover to its original form by immersing in pure water. Since its excellent metal ion and UV-light stimuli-responsive and mechanical properties, the hydrogel has potential applications in the field of soft actuators.

Light can interfere like a wave in a multi-path experiment, but it also has particle properties when interacting with matter. In a closer look, the interference pattern is created by many individual detections ("clicks"), which do not all occur simultaneously. An established assumption is therefore that a single light particle is capable of interfering with itself by superimposing all possibilities to get from the source to the detector. This is in stark contrast to our experience with macroscopic objects, which always "decide" in favour of only one of the alternative paths.In 2010, Jin et al. (Ref. 15) described an event-based model which allowed the authors to show that an interference pattern consisting of clicks can arise in a multi-path experiment even if photons, like macroscopic objects, only follow one path. To do this, photons must be able to transmit the information about their travelling duration to the detector and the detector must have a basic memory. A threshold function uses the message of several light quanta to decide whether a single detection is initiated, which is not the evidence for a single photon. In this "proof of principle", the authors do not claim that the detector function is a realistic one.In the present paper, this detector is replaced by a material consisting of ionizable molecules whose interaction with light takes place according to a modified version of Einstein's radiation laws. Based on this, a photon pair interaction mediated by matter takes place, which in a multi-path experiment generates an interference pattern of clicks at the detector, even if an arbitrary amount of time elapses between the individual detections. In the present model an interference pattern with minima that have less than half the intensity of the maxima is the result of a peculiar behaviour of the detector: In this case, the entirety of its electrons must be described as a unit (a “field”) with many equidistant energy levels. The results of a simulation are presented which enable the model to be tested in experiments.

This paper proposes an analytical model of the double-stator spoke-type permanent-magnet vernier machine (DSSTVM) using the subdomain model (SDM), which can be used to calculate the mag-netic field distribution and corresponding electromagnetic parameters of the DSSTVM. The whole field domain is divided into several subdomains according to the magnetic characteristics of each region, within which Laplace's and Poisson's equations are solved accordingly in terms of magnetic vector potential (MVP). Then, the magnetic flux density distribution, back electromotive force (EMF), and electromagnetic torque of the DSSTVM can be obtained correspondingly. Ultimately, finite element analysis (FEA) is adopted to validate the proposed analytical model's effectiveness for quickly predicting the no-load and on-load performances of the DSSTVM.

Oxygen evolution reaction (OER) is a key half-reaction in electrocatalytic water splitting. Large-scale water electrolysis is hampered by the commercial precious metal-based OER electrocatalysts owing to their high cost and slow kinetics. To address these issues, we present a facile one-pot room-temperature coprecipitation method to quickly synthesize carbon nanotubes-interconnected amorphous NiFe-layered double hydroxides (NiFe-LDH@CNT) as low-cost, efficient and stable OER electrocatalyst. NiFe-LDH@CNT hybrid catalyst delivers outstanding OER performance with a low onset overpotential of 255 mV and a small Tafel slope of 51.2 mV dec-1, as well as outstanding long-term stability. The terrific catalytic capability of NiFe-LDH@CNT can be associated with the synergistic effects of its room-temperature synthesized amorphous structure, bi-metallic modulation, and conductive CNT skeleton. The room-temperature synthesis can not only offer economic feasibility, but also obtain amorphous NiFe-LDH without crystalline boundaries, facilitating long-term stability during OER process. The bi-metallic nature of NiFe-LDH guarantees a modified electronic structure, providing additional catalytic sites. Simultaneously, the highly conductive CNT network fosters a nanoporous structure, facilitating electron transfer, O2 release and enriching catalytic sites. This study presents a strategy to purposefully design nanoarchitecture and facilely synthesize amorphous transition metal-based OER catalysts, ensuring the cost effectiveness, production efficiency, and long-term stability.

Bone metastasis detection and quantification on bone scintigraphy is challenging and clinical important for treatment and patient’s life quality. To develop a CNN based diagnostic system for automated segmentation on bone metastasis regions is non-trivial, especially for a small dataset. A dataset in house comprising 100 breast cancer patients and 100 prostate cancer patients is utilized for this research. The Double U-Net model is adapted through the integration of background removal, adding negative samples, and transfer learning methods for bone metastasis detection. The performance is investigated via 10-fold cross-validation and computed in pixel-wise scale. The best model we achieved has precision of 63.08%, sensitivity of 70.82%, and F1-score of 66.72%. The developed system has the potential to provide pre-diagnostic reports for physicians in final decisions and the calculation of the bone scan index (BSI) with the combination with bone skeleton segmentation.

Channel estimation is an important module to enhance the performance of orthogonal frequency division multiplexing (OFDM) systems. However, the presence of a large amount of noise in multipath fading time-varying channels significantly affects the channel estimation accuracy and thus the recovery quality of the received signals. Therefore, this paper proposes a double-threshold (DT) channel estimation method based on adaptive frame statistics (AFS). The method first adaptively determines the number of statistical frames based on the temporal correlation of the received signals, and preliminarily detects the channel structure by analyzing the distribution characteristics of multipath sampling points and noise sampling points during adjacent frames. Subsequently, a multi-frame averaging technique is used to expand the distinction between multipath and noise sampling points. Finally, the DT is designed to better recover the channel based on the preliminary detection results. Simulation results show that the proposed adaptive frame statistics-double-threshold (AFS-DT) channel estimation method is effective and has better performance compared with many existing channel estimation methods.

Environmental and occupational exposure to hexavalent chromium, Cr(VI), causes female reproductive failures and infertility. Cr(VI) is used in more than 50 industries and is a group-A carcinogen, mutagenic and teratogenic, and a male and female reproductive toxicant. Our previous findings indicate that Cr(VI) causes follicular atresia, trophoblast cell apoptosis, and mitochondrial dysfunction in metaphase II (MII) oocytes. However, the integrated molecular mechanism of Cr(VI)-induced oocyte defects are not understood. The current study investigates the mechanism of Cr(VI) in causing meiotic disruption of MII oocytes, leading to infertility in superovulated rats. Postnatal day (PND)-22 rats were treated with potassium dichromate (1 and 5 ppm) in drinking water from PND 22-29 and superovulated. MII oocytes were analyzed by immunofluorescence, and images were captured by confocal microscopy and quantified by Image Pro Plus software. Our data showed that Cr(VI) increased microtubule misalignment, missegregation of chromosomes, a bulged and folded actin cap, oxidative DNA and protein damage, increased DNA double-strand break, and DNA repair protein RAD51. Cr(VI) also induced incomplete cytokinesis and delayed polar body extrusion. Our study indicates that exposure to environmentally relevant doses of Cr(VI) caused severe DNA damage, distorted oocyte cytoskeletal proteins, and caused oxidative DNA and protein damage leading to infertility.

In order to solve the interference of narrowband communication system to ultra-wideband (UWB) system and meet the design requirements of high isolation of multiple-input multiple-output (MIMO) antenna, two MIMO antennas with double notch structures are designed. Firstly, a two-element antenna was placed symmetrically in parallel, and two rectangular branches were loaded to improve the isolation. U-shaped slots and inverted U-shaped slots are etched on the radiating patch and feeder to achieve notch characteristics in WIMAX and ITU band, respectively. Then, in order to meet more application scenarios, a four-element MIMO antenna is designed, where each element is placed orthogonally to each other, and the isolation is improved by loading a cross-shaped branches in the middle of elements. Both antenna samples are tested to verify the design. Measured results show that the working bandwidth of the two-element UWB MIMO antenna is 2.45-14.88 GHz, the isolation is greater than 17 dB, the peak gain is 5.7 dB, the maximum radiation efficiency can reach 96%, the envelope correlation coefficient (ECC)is less than 0.02. Meanwhile, the working bandwidth of the four-element antenna is 2.14-14.95 GHz, the isolation is greater than 20 dB, the peak gain is 5.9 dB, the maximum radiation efficiency can reach 95%, the ECC is lower than 0.05. They both are with very good omnidirectional characteristic, and meet the requirements of the UWB application.

Particles and photons appear to be total opposites; the former has rest mass which requires space to exist; the latter has kinetic energy which requires time to occur (oscillate). But they do share certain properties (e.g., quantization) that remain invariant when one is transformed (swapped) for the other. This gauge invariance is developed in some detail.The symmetry between particle and photon turns out to be one of inversion. It is the equalities of special relativity that support this inversion and the accompanying invariances: mass transformed to energy; space transformed to time. The great advantage of these symmetries (inversions) is that they provide guidance for an object little understood (the photon) based upon an object well understood (the particle). On this basis, progress can be made in the understanding of some long-standing issues: wave-particle duality, time’s arrow, the constant speed of light and nonlocality.

This study estimates the effects of double long memory and structural breaks on the persistence level of six major cryptocurrency markets. We apply the Bai and Perron’s structural break test, Inclán and Tiao’s iterated cumulative sum of squares (ICSS) algorithm, and the fractionally integrated generalized autoregressive conditional heteroscedasticity (FIGARCH) model with different distributions. The results show that long memory and structural breaks characterize the conditional volatility of cryptocurrency markets and confirm our hypothesis that ignoring structural breaks leads to an underestimation of the persistence of volatility modelling. The ARFIMA-FIGARCH model with structural breaks and a skewed Student–t distribution fits the cryptocurrency market’s price dynamics well.

We investigated experimentally, analytically and numerically the formation process of double emulsion formations under dripping regime in a tri-axial co-flow capillary device. The results show that mismatches of core and shell droplets under a given flow condition can be captured both experimentally and numerically. We propose a semi-analytical model using the match ratio between the pinch-off length of the shell droplet and the product of the core growth rate and its pinch-off time. The mismatch issue can be avoided if the match ratio is lower than unity. We considered a model with the wall effect to predict the size of the matched double emulsion. The model shows slight deviations with experimental data if the Reynolds number of continuous phase is lower than 0.06, but asymptotically approaches to good agreement if the Reynolds number increases from 0.06 to 0.14. The numerical simulation generally agrees with the experiments under various flow conditions.