The 2019 Novel Coronavirus (COVID-19) has caused an acute reduction in world supplies of personal protective equipment (PPE) due to increased demand. To combat the impending shortage of equipment including N95 masks, the George Washington University Hospital (GWUH) developed a 3D printed reusable N95 comparable respirator that can be used with multiple filtration units. We evaluated several candidate prototype respirator models, 3D printer filaments, and filtration units detailed here. Our most recent working model was based on a respirator found on an open source maker website and was developed with PLA (printer filament), a removable cap, a removable filtration unit consisting of two layers of MERV 16 sandwiched between MERV 13, and removable elastic bands to secure the mask. Our candidate mask passed our own suction test protocol to evaluate leakage and passed a qualitative Bitrix N95 fit test at employee health at GWUH. Further efforts are directed at improving the current model for seal against face, comfort, and sizing. The 3D model is available upon request and in the supplement of this paper. We welcome collaboration with other institutions and suggest other facilities consider mask fit for their own population when exploring this concept.

Very well into the dawn of the fourth industrial revolution (industry 4.0), we hardly distinguish between what is artificial and what is natural (e.g. man-made virus and natural virus). Thus, the level of discombobulation among people, companies or countries is indeed unprecedented. The fact that industry 4.0 is explosively disrupting or retrofitting each and every industrial sector, makes industry 4.0 the famous buzzword amongst researchers today. However, the insight of industry 4.0 disruption in the industrial sectors remains ill-defined in both academic and non-academic literature. The present study aimed at identifying industry 4.0 neologisms, understanding the industry 4.0 disruption and illustrating the disruptive technologies convergence in the major industrial sectors. A total of 99 neologisms of industry 4.0 were identified. Industry 4.0 disruption in Education industry (Education 4.0), Energy industry (Energy 4.0), Agriculture industry (Agriculture 4.0), Healthcare industry (Healthcare 4.0), and Logistics industry (Logistics 4.0) are described. The convergence of 12 disruptive technologies including 3D printing, Artificial intelligence, Augmented reality, Big Data, Blockchain, Cloud computing, Drones, Internet of things, Nanotechnology, Robotics, Simulation and Synthetic biology in agriculture, healthcare and logistics industries are illustrated.

It is common knowledge that increasing CO₂ concentration plays a major role in enhancement of the greenhouse effect and contributes to global warming. The purpose of this study is to complement the conventional and established theory that increased CO₂ concentration due to human emissions causes an increase of temperature, by considering the reverse causality. Since increased temperature causes an increase in CO₂ concentration, the relationship of atmospheric CO₂ and temperature may qualify as belonging to the category of “hen-or-egg” problems, where it is not always clear which of two interrelated events is the cause and which the effect. We examine the relationship of global temperature and atmospheric carbon dioxide concentration at the monthly time step, covering the time interval 1980–2019, in which reliable instrumental measurements are available. While both causality directions exist, the results of our study support the hypothesis that the dominant direction is T → CO₂. Changes in CO₂ follow changes in T by about six months on a monthly scale, or about one year on an annual scale. We attempt to interpret this mechanism by involving biochemical reactions, as at higher temperatures soil respiration, and hence CO₂ emission, are increasing.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

Synthesis of styrene butadiene hybrid latex was performed via emulsion polymerization technique using various amount of laponite clay as filler. Laponite clay was modified with cationic surfactant methyl triphenylphosphonium bromide (MTPB) with ion exchange technique prior to polymerization process. The main objective of the modification is to render the surface of the clay layers to more organophilic. Emulsion polymerization was performed under semi batch process using 2 L laboratory stainless steel reactor with temperature 85°C to 90°C for 8 hours. Polymer hybrid styrene butadiene latex was characterized for its physical and chemical properties with standard ASTM Methods. Characterization of its binding and printing properties were carried out with standard testing method (TAPPI Methods) using single coating formulation on 80 gsm woodfree paper. Polymer hybrid latex based on styrene and butadiene monomers with laponite clay enhanced binding and printing properties of coated paper, addition of laponite clay to 6.0 wt % increased the binding resistance of the coated paper two times higher than pure latex. Reducing binder level become possible for cost saving.

The maker movement has reached the optics labs, empowering researchers to actively create and modify microscope designs and imaging accessories. 3D printing has especially had a disruptive impact on the field, as it entails an accessible new approach in fabrication technologies, namely additive manufacturing, making prototyping in the lab available at low cost. Examples of this trend are taking advantage of the easy availability of 3D printing technology. For example, inexpensive microscopes for education have been designed, such as the FlyPi. Also, the highly complex robotic microscope OpenFlexure represents a clear desire for the democratisation of this technology. 3D printing facilitates new and powerful approaches to science and promotes collaboration between researchers, as 3D designs are easily shared. This holds the unique possibility to extend the open-access concept from knowledge to technology, allowing researchers from everywhere to use and extend model structures. Here we present a review of additive manufacturing applications in microscopy, guiding the user through this new and exciting technology and providing a starting point to anyone willing to employ this versatile and powerful new tool.

Introduction: The term 3D printing is commonly used to depict an assembling method whereby the final form of an object is the result of the addition of different layers to build the frame of an object. This procedure is more accurately portrayed as additive manufacturing and is likewise alluded to as fast prototyping. The term 3D printing, in any case, is generally new and has been an active part of current developments in Dentistry. Much publicity encompasses the evolution of 3D printing, which is hailed as an innovation that will perpetually change CAM manufacturing, including in the dental sector. This review is the first part in a 3D Printing series that looks at the history of 3D Printing, the technologies available and reviews the literature relating to the accuracy of these technologies. Conclusions: The recent advancement in digital dentistry to incorporate these tools has modernised dental practices by paving the way for computer-aided design (CAD) technology and rapid prototyping. The use of 3D printing has led to 3D digital models produced with intraoral scanners (IOS), which can be manipulated easily for diagnosis, treatment planning, mockups, and a multitude of other uses. Combining 3D Printing with a 3D intraoral scan eliminates the need for physical storage but makes it to retrieve a 3D models for use within all dental modalities.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

This paper presents the systematic development and performance characterization of a non-proprietary 3D-printable ultra-high-performance fiber-reinforced concrete (UHPFRC) for digital construction. Several fresh and hardened properties of the developed 3D-printable UHPFRC matrix (without fiber) and composite (with 2% volume fraction of steel fibers) were evaluated and compared to that of conventionally mold-cast UHPFRC. Additionally, the effects of testing direction on the compressive and flexural strengths of the printed UHPFRC were investigated. The fresh properties of the UHPFRC developed in this study satisfied the criteria for extrudability, buildability, and shape-retention-ability, which are relevant for ensuring printability. The printed UHPFRC exhibited superior flexural performance to the mold-cast UHPFRC due to alignment of the short fibers in the printing direction. The high compressive and flexural strengths, along with the deflection-hardening behavior, of the developed UHPFRC can enable the production of thin 3D-printed components with significant reduction or complete elimination of conventional steel bars.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

Recently, many authors have been interested to introduce fuzzy implications over t-norms and t-conorms. In this paper, we introduce (S,N) and residuum fuzzy implication for Dubois t-norm and Hamacher's t-norm. Also, new concepts so-called (T,N) and residual fuzzy co-implication in dual Heyting Algebra are investigated. Some examples as well as application are discussed as well.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

Background: On late December 2019, a viral pneumonia known as coronavirus disease 2019 (COVID-19), was originated from China and spread very rapidly in the world. Therefore, COVID-19 became a global concern and health problem. Methods: We presented four patients in this study. They were selected from patients who presented with pneumonia symptoms and were suspicious for COVID-19 and referred to the intended centers for COVID-19 diagnosis and management of Shiraz University of Medical Sciences in the south of Iran. Two nasopharyngeal and oropharyngeal throat swab samples were collected from each patient and tested for severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) detection by real-time reverse-transcriptase–polymerase-chain-reaction (RT-PCR), and also samples were sent for influenza viruses and all the respiratory panel. Results: In the present report, four patients were diagnosed in the starting days of COVID-19 disease in our center in south of Iran with co-infection of SARS-CoV-2 and influenza virus. Conclusions: This co-infection of COVID-19 and influenza highlights the importance of considering SARS-CoV-2 PCR assay regardless of other positive findings for other pathogens in the primary test during the epidemic.

Mass transfer restrictions of scaffolds are currently hindering the development of three-dimensional (3D), clinically viable, and tissue engineered constructs. For this situation, a 3D poly(lactide-co-glycolide)/hydroxyapatite porous scaffold, which was much favorable for transfer of nutrients to and waste products from the cells in the pores, was developed in this study. The 3D scaffold had an innovative structure, including macropores with diameters of 300−450 μm for cell ingrowth and microchannels with diameters of 2−4 μm for nutrition and waste exchange. The mechanical strength in wet state was strong enough to offer the structural support. The typical structure was more beneficial for the attachment, proliferation, and differentiation of rabbit bone marrow mesenchymal stem cells (rBMSCs). The alkaline phosphatase (ALP) activity and calcium (Ca) deposition were evaluated on the differentiation of rBMSCs, and the results indicated that the microchannel structure was very favorable for differentiating rBMSCs into maturing osteoblasts. For repairing rabbit radius defects in vivo, there was rapid healing in the defects treated with the 3D porous scaffold with microchannels, where the bridging by a large bony callus was observed at 12 weeks post-surgery. Based on the results, the 3D porous scaffold with microchannels was a promising candidate for bone defect repair.

Good governance in natural resource management (NRM) is one of the most challenging issues in developing countries that often inappropriately embedded in national policies and political agendas. It is, in fact, even more important for countries like Bangladesh with exceptionally high pressure and dependence on its natural resources for sustaining rural livelihoods. Globally, nowadays, good governance is considered as one of the key factor for achieving the goal of sustainable development and biodiversity conservation. Bangladesh, of late has responded to that global zeal by involving local communities in the management of country’s declining forest and other natural resources. The colonial legacy of the forestry sector of Bangladesh was planned and, managed as interim projects through donors’ prescriptions. Thus, institutions, management processes and conservation outcomes were problematic. The conventional approach adopted by colonial and post-colonial regimes for forest management also proved to be inefficient due to its top-down management system. The absolute dependency on donor support, and their prescription sometimes worsened the situation both ecologically and socially. Global, regional and local trends supported the need for a different dimension in the governance paradigms. The introduction of a pluralistic approach, known as co-management in protected areas (PAs) is an example of an attempt whereby shared governance mechanism are implemented to attain the desired goals of conservation that will also address the livelihoods and aspirations of communities living in and around PAs of the country. However, in designing future forest and PA regimes the concern of the external aid support and attached conditions remain a reality that needs to be addressed. Adequate attention should be given to our vanishing biodiversity, culture and community livelihoods through devising an appropriate governance mechanism recognizing and supporting local rights, access and participation in the environmental management. It is now time to mainstream the adhoc nature of governance according to our national conservation strategy and policy frameworks in order to achieve the goals and objectives of the Bangladesh NRM sector addressing the human and community right of people in the specific context of forest protected areas management.

In our study we investigated the additive manufacturing (AM) of ceramic-based Functionally Graded Materials (FGM) by the direct AM technology Thermoplastic 3D-Printing (T3DP). Zirconia components with a varying microstructure were additively manufactured by using thermoplastic suspensions with different contents of pore forming agents (PFA) and were co-sintered defect-free. Different materials were investigated concerning their suitability as PFA for the T3DP process. Different zirconia-based suspensions were prepared and used for AM of single- and multi-material test components. All samples were sintered defect-free and in the end we could realize a brick wall-like component consisting of dense (<1% porosity) and porous (approx. 5% porosity) zirconia areas to combine different properties in one component. The T3DP opens the door to AM of further ceramic-based 4D-components like multi-color or multi-material, especially multi-functional components.

SARS-CoV2 RNA depended RNA polymerase is an essential enzyme for the survival of the virus in hosts as it helps in the replication of viral RNA. There are no human polymerases that share either sequence or structural homology with viral RNA depended RNA polymerase. These make it a good target for inhibitor discovery, as a specific inhibitor cannot cross-react with the human polymerases. We have used virtual screening, docking, binding energy calculation and simulation to show that valproic acid Co-A, a metabolite from prodrug valproic acid, forms stable interaction with nsP12 of CoV. Our results suggest valproic acid Co-A could be a potential inhibitor of nsP12 of SARS-CoV2.

Collision avoidance is an important feature in advanced driver-assistance systems, aiming at providing correct, timely and reliable warnings before an imminent collision (objects, vehicles, pedestrians, etc.). A co-simulation framework is proposed in this paper to address the design and evaluation of collision avoidances in a cyber-physical system. The co-simulation framework is supported on the interaction between SCANeR and Matlab/Simulink. From the best of authors’ knowledge, two main contributions are reported in this paper. Firstly, the modelling and simulation of virtual on-chip LIDAR sensors in a cyber-physical system (CPS) considering traffic scenarios is presented. The CPS is designed and implemented in SCANeR. Secondly, an obstacle recognition library with three specific Artificial Intelligence-based methods is also designed based on sensory information database provided by SCANeR. Three methods for collision avoidance detection are considered, i.e.; a multi-layer perceptron neural network, a self-organization map and a support vector machine. Finally, a comparison among these methods for detecting obstacles before different weather conditions is done with very promising results in terms of accuracy. The best results are achieved using the multi-layer perceptron in sunny and fog conditions, the support vector machine in rainy and self-organized map in snowy conditions.

Abstract The COVID-19 pandemic has tremendously affected the African continent and the rest of the world. Most businesses have closed and a lot of people have lost their jobs. The aviation industry has been shaken to the core with airlines losing millions of dollars and flights being cancelled. The tourism industry has consequently been affected due to restricted travel of tourists, impacting wildlife conservation and livelihoods. Schools, colleges and universities have been closed. The virus has infected millions of people and hundreds of thousands of people have died globally putting strain on health systems especially those of hard hit countries. Various countries all over the world have put measures to control the spread of the virus through lockdowns and social distancing policies. The reduced economic activities and mobility of people has resulted in improved air quality, cleaner water and beaches in some countries. However there are also negative impacts such as challenges in waste management, increased pharmaceutical and household waste and discovery of the corona virus in wastewater, a potential threat to public health. A considerable amount of research has been done on the socio-economic impacts of COVID-19 in Africa but there is still limited research on its impact on the environment. This paper serves to highlight the observed and potential environmental impacts of COVID-19 in Africa.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

Though Cyber Physical Systems (CPS) become very popular in last the decade, dependability of CPS is still a critical issue and related survey is rare. We try to spell out the jigsaw of technologies and figure out the technical trends of dependable self-managing CPS. This survey first recalls the motivation and the similar concepts. By analyzing four generic architectures, we summarize the common characteristics and related assurance technologies, and propose a more generic environment-in-loop processing flow of CPS and a formal interaction flow between physical space and cyber space. Further, the similarity between correctness and dependability is formally analyzed and the new five research questions of dependable self-managing CPS are presented. Then we review the critical technologies and related correctness verification & validation (V&V) methods, the architectures for dependable self-managing CPS. Further, the detail dependability management and V&V technologies are surveyed, which covers the areas of running-time fault management methods and whole life cycle V&V technologies, maintenance and available tool sets. For holistic CPS development, Modeling techniques and MDE (model driven engineering) based V&V methods are analyzed in detail. Then we complete the jigsaw of technologies and figure out the missing part. Further, we propose the technical challenges and the further direction. To our best knowledge, this is the first comprehensive survey on dependable self-managing CPS development and evaluation.

Inexpensive piezoelectric diaphragms can be used as sensors to facilitate both nozzle height setting and build platform leveling in FFF (Fused Filament Fabrication) 3D printers. Tests simulating nozzle contact are conducted to establish the available output and an output of greater than 8 Volts found at 20 ºC, a value which is readily detectable by simple electronic circuits. Tests are also conducted at a temperature of 80 ºC and, despite a reduction of greater than 80% in output voltage, this is still detectable. The reliability of piezoelectric diaphragms is investigated by mechanically stressing samples over 100,000 cycles at both 20 ºC and 80 ºC and little loss of output over the test duration is found. The development of a nozzle contact sensor using a single piezoelectric diaphragm is described.

Background: Previously, our laboratory has provided evidence that pre-administration of the antioxidant, lipoic acid covalently bonded to various naturally occurring antioxidants, enhanced neuroprotective capacity compared to the administration of lipoic acid on its own. The naturally occurring compound scopoletin, a coumarin derivative, has been shown in various in vitro studies to have both antioxidant and anti-inflammatory mechanism of actions. To date, the effect of scopoletin on neuronal cell death in an in vivo model of ischemia or ischemia-reperfusion has not been investigated. Therefore, the present investigation was designed to determine if scopoletin on its own, or a co-drug consisting of lipoic acid and scopoletin covalent bond, named UPEI-400, would be capable of demonstrating a similar neuroprotective efficacy. Methods: Using a rodent model of stroke in male rats (anesthetized with Inactin®; 100 mg/kg, iv), the middle cerebral artery was permanently occluded for 6 hours (pMCAO), or in separate animals, occluded for 30 min followed by 5.5 hrs of reperfusion (ischemia/reperfusion; I/R). Results: Pre-administration of either scopoletin or UPEI-400 significantly decreased infarct volume in the I/R model (p<0.05), but not in the pMCAO model of stroke. However, UPEI-400 was ~1000 times more potent as compared to scopoletin on its own. The optimal dose of UPEI-400 was then injected during the occlusion and at several time points during reperfusion and significant neuroprotection was observed for up to 150 mins following the start of reperfusion (p<0.05). Conclusion: The data suggest that synthetic combination of scopoletin with lipoic acid (UPEI-400) is a more effective neuroprotectant that either compound on their own. Also, since UPEI-400 was only effective in a model of I/R, it is possible that it may act to enhance neuronal antioxidant capacity and/or upregulate anti-inflammatory pathways to prevent the neuronal cell death.

Introduction: The current generation of 3D printers are lighter, cheaper, and smaller, making them more accessible to the chairside digital dentist than ever before. 3D printers in general in the industrial and chairside setting can work with various types of materials including, metals, ceramics, and polymers. Evidence presented in many studies show that an ideal material used for dental restorations is characterised by several properties related to durability, cost-effectiveness, and high performance. This review is the second part in a 3D Printing series that looks at the literature on material science and applications for these materials in 3D printing as well as a discussion on the potential further development and future evolution in 3D printing materials. Conclusions: Current materials in 3D printing provide a wide range of possibilities for providing more predictable workflows as well as improving efficiency through less wasteful additive manufacturing in CAD/CAM procedures. Incorporating a 3D printer and a digital workflow into a dental practice is challenging but the wide range of manufacturing options and materials available mean that the dentist should be well prepared to treat patients with a more predictable and cost effective treatment pathway. As 3D printing continues to become a commonplace addition to chair side dental clinics, the evolution of these materials, in particular reinforced PMMA, resin incorporating zirconia and glass reinforced polymers offer increased speed and improved aesthetics that will likely replace subtractive manufacturing milling machines for most procedures.

AbstractWhile the technology is relatively new, low cost 3D printing has impacted many aspects of human life. 3D printers are being used as manufacturing tools for a wide variety of devices in a spectrum of applications ranging from diagnosis to implants to external prostheses. The ease of use and availability of 3D design software and low cost has made 3D printing an accessible manufacturing and fabrication tool in many research laboratories. 3D printers can print materials with varying density, optical character, strength and chemical properties providing platforms for a huge number of strategies that can be chosen for user’s needs. In this review, we focus on applications in biomedical diagnostics and how this revolutionary technique is facilitating development of low cost, sensitive and often geometrically complex tools. 3D printing in fabrication of microfluidics, supporting equipment, optical and electronic components of diagnostic devices is presented. Emerging diagnostic 3D bioprinting as a tool to incorporate living cells or biomaterials into 3D printing is also discussed.

The possibility of using additive manufacturing (AM) in the medicine area has created a new opportunities in health care. This has contributed to a sharp increase in demand for 3D printers, their systems and materials that are adapted to strict medical requirements. We described herein a medical-grade thermoplastic polyurethane (S-TPU), which was developed and then formed into a filament for Fused Deposition Modeling (FDM) 3D printers during a melt-extrusion process. S-TPU consisting of aliphatic hexamethylene 1,6-diisocyanate (HDI), amorphous α,ω-dihydroxy(ethylene-butylene adipate) (PEBA) and 1,4 butandiol (BDO) as a chain extender, was synthesized without the use of a catalyst. The filament properties were characterized by rheological, mechanical, physico-chemical and in vitro biological properties. The tests showed biocompatibility of the obtained filament as well as revealed no significant effect of the filament formation process on its properties. This study may contribute to expanding the range of medical-grade flexible filaments for standard low-budget FDM printers.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

Pharmaceutically active compounds and organic pollutants are becoming a major environmental dispute possessing serious threat to the water bodies and terrestrial ecosystem. Microorganisms are capable of the self-purification process, and hence the microbial degradation is considered a lucrative method to counteract the therapeutic and recalcitrant pollutants. Pharmaceutical toxicants in aquatic system can be treated by conventional wastewater treatment, but slow sludge settling, presence of mixture of pharmaceuticals and recalcitrant compounds often pose a potential ecological risk. Some microbial strains are very effective in reducing the chemical oxygen demand (COD), biological oxygen demand (BOD), total dissolved solids (TDS), and turbidity in pharmaceutical industrial wastewater treatment. The natural microbial community has a significant role in the ecological processes of pharmaceutical and organic compounds, including non-steroidal anti-inflammatory drugs, analgesics, blood lipid regulators and other micropollutants. Specific bacterial isolates can act as biodegraders, and fungal treatment could offer protection to the ecosystem. These microorganisms use the pollutants as their sole carbon source and transform the contaminants by co-metabolic pathways. Natural attenuation by native microorganisms, biostimulation and bioaugmentation are the processes employed to degrade the target contaminant. Microorganisms may also be genetically engineered to improve the neutralization efficiency, which would assist in the mineralization of the pollutants. Thus, employing microorganisms to detoxify the pollutants probably enhances the sustainable potential biodegradability, improves water quality standards and ensures eco-friendly alternative bioremediation strategy.

The corona (COVID-19) pandemic offers an opportunity for dealing with persistent problems, through a transformative recovery process. It is a crisis that offers opportunities for dealing with three interrelated crises: the ecological crisis (climate change, loss of biodiversity, resource depletion, pollution and ecosystem destruction), the confidence crisis (people losing trust in government, politics, companies, regular news channels, science, each other and the future), and the inequality crisis (the widening of the gap between rich and poor). Our argument is that sustainability transitions will not succeed without a different economy and another social contract with the associated rights and duties of care (for the environment and the well-being of others, including future generations). A different social contract is not only desirable from the point of view of sustainability and fairness, justice and equality, but is also necessary to restore citizens' trust in politics, government, companies and each other. In the paper we discuss mechanisms towards a Natural Social Contract, systemic leverage points for system transformations and possibilities for co-evolutionary governance by actor coalitions interested in transformative change. The combination of those three elements helps to synchronize different agendas and reduce the chance that they will work against each other.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

Introduction The COVID-19 virus was initially reported in Dec 2019 as the causative agent of a pneumonia breakout in Wuhan China. This virus rapidly spread from China to Europe and the East Coast of the United States eventually reaching the South West United States and indigenous tribes in mid -March. Since, then the indigenous tribes have been devasted by the virus which the Governor of New Mexico has likened as an existential threat. Methodology A PubMed search was performed utilizing the words: Navajo Indian, Indigenous Indian, Wuhan Virus, COVID-19, SARs coronavirus, ACE2, S protein, virulence, clinical presentation, epidemiology, genome, treatment, structure, MERs, pathogenesis and/or pathology alone and in combination with other terms. Each paper was evaluated by three content experts for quality, reproducibility, credibility and reputation of the journal Results: Navajo’s and other indigenous peoples may have elevated levels of ACE2 receptors in their lungs and other tissues allowing greater susceptibility to the COVID-19 virus. Increased levels of diabetes and protein nutrition are directly related to increased morbidity and mortality in this group while obesity, COPD, and heart diseas are not. The increased morbidity and mortality is exasperated by an inability to test for COVID-19 Conclusion: The infectivity rate of Navaho’s on the reservation is 22 times higher than the national average with a death rate near 4%. Comorbidites account for some of the increased morbidity and mortality while lack of access to adequate health care unnecessarily magnifies the poor outcome. The threat to indigenous tribes in the Southwest of COVID-19 is dire.

This study provides designs for a low-cost, easily replicable open source lab-grade digital scale that can be used as a precision balance. The design is such that it can be manufactured for use in most labs throughout the world with open source RepRap-class material extrusion-based 3-D printers for the mechanical components and readily available open source electronics including the Arduino Nano. Several versions of the design were fabricated and tested for precision and accuracy for a range of load cells. The results showed the open source scale was found to be repeatable within 0.1g with multiple load cells, with even better precision (0.01g) depending on load cell range and style. The scale tracks linearly with proprietary lab-grade scales, meeting the performance specified in the load cell data sheets, indicating that it is accurate across the range of the load cell installed. The smallest loadcell tested(100g) offers precision on the order of a commercial digital mass balance. The scale can be produced at significant cost savings compared to scales of comparable range and precision when serial capability is present. The cost savings increase significantly as the range of the scale increases and are particularly well-suited for resource-constrained medical and scientific facilities.

Buildability, i.e. the ability of a deposited material bulk to retain its dimmensions under increasing load, is an inherent prerequisite for formwork-free digital construction (DC). Since DC processes are relatively new, no standard methods of characterization are available yet. The paper at hand presents practice-oriented buildabilty criteria by taking various process parameters and construction costs into consideration. In doing so, direct links between laboratory buildability tests and target applications are established. A systematic basis for calculating the time interval (TI) to be followed during laboratory testing is proposed for the full-width printing (FWP) and filament printing (FP) processes. The proposed approach is validated by applying it to a high-strength, printable, fine-grained concrete. Comparative analyses of FWP and FP revealed that to test the buildability of a material for FP processes, higher velocities of the printhead should be established for laboratory tests in comparison to those needed for FWP process, providing for equal construction rates.

3D printing facilitates the straightforward construction of microchannels with complex three-dimensional architectures. Here, we demonstrate 3D-printed modular mixing components that operate on the basis of splitting and recombining fluid streams to decrease interstream diffusion length. These are compared to helical mixers that operate on the principle of chaotic advection.

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

The Estimation of systemic risk in India is still in its infancy stage. There are several methods which are available but none of the methods are fully compatible to forecast the systemic risk since under different circumstances the factors responsible for the risk differs. In this paper the systemic risk estimation in India being carried out based on spread in daily stock market price(Difference between the bid and ask price of a share) of the top 100 firms in India according to market capitalization for the period of July2007 to March 2016. The results were compared with the Financial Stability Report published by Reserve Bank Of India for the period of March 2010 to June 2016.The results clearly indicates that there exits relationship between market illiquidity represented by spread and risks associated with the Financial System. In most of the cases the Z score (deviation from the mean/Standard Deviation) of the spread has become negative which provides the spread which is farther from the mean, also a good indicator of volatility in market and risk to financial system. It is also seen that the Systemic Risk Survey conducted by Reserve Bank of India which started during October 2011 has supported the results.

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

Porous MnO/C microspheres have been successfully fabricated by a fast co-precipitation method in a T-shaped microchannel reactor. The structures, compositions and electrochemical performances of the obtained MnO/C microspheres are characterized by X-ray diffraction, emission scanning electron microscopy, transmission electron microscopy (HRTEM), Brunauer–Emmett–Teller analysis, charge-discharge testing, cyclic voltammograms, and electrochemical impedance spectra. Experimental results reveal that the as-prepared MnO/C, with a specific surface area of 96.66 m²·g^–1 and average pore size of 24.37 nm, exhibits excellent electrochemical performance, with a discharge capacity of 655.4 mAh·g^–1 after cycling 50 times at 1 C and capacities of 808.3, 743.7, 642.6, 450.1, and 803.1 mAh·g^–1 at 0.2, 0.5, 1, 2, and 0.2 C, respectively. Moreover, the controlled method of using a micro-channel reactor, which can produce larger specific surface area porous MnO/C with improved cycling performance by shortening lithium-ion diffusion distances, can be easily applied in real production on a large-scale.

In this work, we report synthesis of Cu, Pt and Pd doped SnO₂ powders and their comparative CO gas sensing studies. Dopants were incorporated into SnO₂ nanostructures using chemical and impregnation methods by using urea and ammonia as precipitation agents. The synthesized samples were characterized using X-ray diffraction (XRD), Raman spectroscopy, Scanning electron microscopy (SEM) and High resolution transmission electron microscopy (HR-TEM). The presence of dopants within the SnO₂ nanostructures was evidenced from HR-TEM. Doped powders utilizing chemical methods with urea as precipitation agent presented higher sensitivities compared to the remaining, which is due to the formation of uniform and homogeneous particles resulted from the temperature assisted synthesis. The particle sizes of doped SnO₂ nanostructures were in the range of 40-100 nm. An enhanced sensitivity around 1783 was achieved with Cu doped SnO₂ when compared with two other dopants i.e., Pt (1200) and Pd: SnO₂(502). The high sensitivity of Cu: SnO₂ is due to formation of CuO and its excellent association and dissociation in the presence of CO with adsorbed atmospheric oxygen at sensor operation temperatures resulted in high conductance. Cu: SnO₂ may be an alternative and cost effective sensor for industrial applications.

The use of flexible sensors has tripled over the last decade due to the increased demand in various fields including health monitoring, food packaging, electronic skins and soft robotics. Flexible sensors have the ability to be bent and stretched during use and can still maintain their electrical and mechanical properties. This gives them an advantage over rigid sensors that lose their sensitivity when subject to bending. Advancements in 3D printing have enabled the development of tailored flexible sensors. Various additive manufacturing methods are being used to develop these sensors including inkjet printing, aerosol jet printing, fused deposition modelling, direct ink writing, selective laser melting and others. Hydrogels have gained much attention in the literature due to their self-healing and shape transforming. Self-healing enables the sensor to recover from damages such as cracks and cuts incurred during use and this enables the sensor to have a longer operating life and stability. Various polymers are used as substrates on which the sensing conductive material is placed. Polymers including polydimethylsiloxane (PDMS), polyvinyl acetate (PVA), and Kapton are extensively used in flexible sensors. The most widely used nanomaterials in flexible sensors are carbon and silver, however, other nanomaterials such as iron, copper, manganese dioxide and gold are also used to provide controlled levels of conductivity or other functional properties.

The 21^st century has witnessed precipitous changes spanning from the way of life to the technologies that emerged. We have entered a nascent paradigm shift (industry 4.0) where science fictions have become science facts, and technology fusion is the main driver. Thus, ensuring that any advancement in technology reach and benefit all is the ideal opportunity for everyone. In this study, disruptive technologies of industry 4.0 was explored and quantified in terms of the number of their appearances in published literature. The study aimed at identifying industry 4.0 key technologies which have been ill-defined by previous researchers and to enumerate the required skills of industry 4.0. Comprehensive literature survey covering the field of engineering, production, and management was done from multidisciplinary databases: Google scholar, ScienceDirect, Scopus, Sage, Taylor & Francis and Emerald insight. Results of the electronic survey showed that 35 disruptive technologies were quantified and 13 key technologies: Internet of things, Big data, 3D printing, Cloud computing, Autonomous robots, Virtual and Augmented reality, Cyber physical system, Artificial intelligence, Smart sensors, Simulation, Nanotechnology, Drones and Biotechnology were identified. Both technical and personal skills to be imparted into the human workforce for industry 4.0 were reported. The study identified the need to investigate the capability and the readiness of developing countries in adapting industry 4.0 in terms of the changes in the education systems and industrial manufacturing settings. The study proposes the need to address integration of industry 4.0 concepts into the current education system.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

There is a rising global concern for the ongoing outbreak of SARS-CoV-2 due to its high transmission rate and unavailability of treatment. Through the binding of its spike glycoprotein with angiotensin type 2 (ACE2), SARS-CoV-2 can efficiently get in the cells of patients and start its pandemic cycle. Herein, the biological diversity of SARS-CoV-2 infection was assessed in Babylon province of Iraq by investigating the possible genetic variations of the spike glycoprotein. A specific coding region of 795 bp within the viral spike (S) gene was amplified from 19 patients who suffered from obvious symptoms of SARS-CoV-2 infection. Sequencing results identified fifteen novel nucleic acid variations with a variety of distributions within the investigated samples. The electropherograms of all the identified variations showed obvious co-infections with at least two different viral strains per sample. Within these co-infections, the majority of samples exhibited three nonsense single nucleotide polymorphism (SNP)s, p.301Cdel, p.380Ydel, and p.436del, which yielded three truncated SARS-CoV-2 spike glycoproteins of 301, 380, and 436 amino acids length, respectively. The network and phylogenetic analyses indicated that for all viral infections were derived from multi-ancestral origins. Results inferred from the specific clade-based tree entailed that some viral strains were derived from European G-clade sequences. In conclusion, our data demonstrated the absence of any single strain infection among all investigated viral samples in the studied area, which may entail a higher risk of SARS-CoV-2 in this country. Through the identified high frequency of truncated spike proteins, we suggest that defective SARS-CoV-2 may depend on helper strains having intact spikes in its infection. Alternatively, another putative ACE2-independent route of viral infection way also suggested. To the best of our knowledge, this is the first report to describe the co-infection of multiple strains of SARS-CoV-2 in patients with COVID-19.

Aim of this research paper is to introduce a novel method of hybrid orthodontic tooth-borne distalizer treatment of class II malocclusion by using 3D printed biocompatible personalized distalizer. Explains 3D designing, printing and clinical application of individualized biocompatible medical device dedicated for orthodontic teeth distalization. Compares such distalizer manufactured from two different biocompatible photopolymers (white and transparent). Evaluates their clinical performance and also patients’ aesthetical perception. Clinical part includes comparison of treatment debonding on the set of 12 complete orthodontic treatments with uni-lateral class II malocclusion managed with hybrid approach (CAT-Invisalign with 3D printed distalizer). Paper offers an evaluation of the personalized distalizer functioning in regard to current publications and comparison to conventional prefabricated alternatives like Carriere® Distalizer™ appliance. Results showed no significance of material differences on clinical performance of such individualized distalizers. Research showed preference of patients towards transparent biocompatible photopolymer instead of white A2 shade.

On the eve of the Brexit process, in the context of a rising Euroscepticism that fuels the modest confidence of European citizens in their national and European institutions, the article assesses the efficiency and effectiveness of the European Parliament within the framework of the ordinary legislative procedure (co-decision). After defining and formulating the main indicators, the paper analyses the micro- and macro-performance of the European Parliament within the decision-making process from a quantitative-qualitative and a qualitative-quantitative perspective, highlighting the relativizing factors and the responsiveness of the European decision-making process to the Europeans’ needs.

The purpose of the present study was to investigate the effects of psychological pressure on corticospinal excitability, the spinal reflex, lower limb muscular activity, and reaction times during a task involving dominant leg movements. Ten healthy participants performed a simple reaction time task by raising the heel of their dominant foot from a switch. After 20 practice trials, participants performed 20 non-pressure and 20 pressure trials in a counterbalanced order. Stress responses were successfully induced, as indexed by significant increases in state anxiety, mental effort, and heart rates under pressure. Significant increases in motor evoked potential (MEP) amplitude of the tibialis anterior muscle (TA) occurred under pressure. In terms of task-related EMG amplitude, the co-contraction rate between the soleus (SOL) and TA muscles significantly increased along with SOL and TA EMG amplitudes under pressure. Hoffmann reflexes for SOL and reaction times did not change under pressure. These results indicate that corticospinal excitability and leg muscle-related EMG activity increase homogeneously during lower limb movements that are performed under psychological pressure.

The COVID-19 crisis has resulted in a shortage of personal protective equipment (PPE) [1]. COVID-19 is currently the leading cause of death in the United States[2]. Health care providers caring for COVID-19 patients or at high risk of being exposed to the SARS-CoV-2 virus benefit from a face shield to protect against aerosol droplets that could hit the face and minimize the chance of inadvertently touching the face with contaminated hands, and air filtration to filter out aerosolized SARS-CoV-2. Adapting commercially available full-faced snorkel masks has been proposed as an alternative to narrow the gap in PPE [3]. Here we explore a full-faced snorkel mask with commercially available particulate filters.

Mangrove forests store and sequester large area-specific quantities of blue carbon (C_org). Except for tundra and peatlands, mangroves store more C_org per unit area than any other ecosystem. Mean mangrove C_org stock is 738.9 Mg C_org ha⁻¹ and mean global stock is 6.17 Pg C_org, which equates to only 0.4–7% of terrestrial ecosystem C_org stocks but 17% of total tropical marine C_org stocks. Seagrasses sequester more C_org per unit area than mangroves (179.6 g C_org m⁻²·a⁻¹) but twice the C_org sequestered by mangroves globally (15 Tg C_org a⁻¹). Mangroves sequester only 4% (range 1.3–8%) of C_org sequestered by terrestrial ecosystems, indicating that mangroves are a minor contributor to global C storage and sequestration. CO₂ emissions from mangrove losses equate to 0.036 Pg CO₂-equivalents a⁻¹ based on rates of C sequestration but 0.088 Pg CO₂-equivalents a⁻¹ based on complete destruction for conversion to aquaculture and agriculture. Mangrove CO₂ emissions account for only 0.2% of total global CO₂ emissions but 18% of CO₂ emissions from the tropical coastal ocean. Despite significant data limitations, the role of mangrove ecosystems in climate change mitigation is globally insignificant but may be more significant and effective at the national and regional scale.

Angiogenesis is a complex process that involves interactions between endothelial cells and various other cell types as well as the tissue microenvironment. Several previous studies have demonstrated that mast cells accumulate at angiogenic sites. In spite of the evidence suggesting a relationship between mast cells and angiogenesis, the association of mast cells and endothelial cells remains poorly understood. The present study aims to investigate the relationship between mast cells and endothelial cells during in vitro angiogenesis. When endothelial cells were co-cultured with mast cells, angiogenesis was stimulated. Furthermore, there was direct intercellular communication via gap junctions between the two cell types. In addition, the presence of mast cells stimulated endothelial cells to release angiogenic factors. Moreover, conditioned medium from the co-cultures also stimulated in vitro angiogenesis. The results from this investigation demonstrate that mast cells have both direct and indirect proangiogenic effects and provide new insights into the role of mast cells in angiogenesis.

In order to understand the effect of Pb-CuI co-doping on the thermoelectric performance of Bi₂Te₃, n-type Bi₂Te₃ co-doped with x at% CuI and 1/2x at% Pb (x = 0, 0.01, 0.03, 0.05, 0.07, and 0.10) were prepared via high temperature solid state reaction and consolidated using spark plasma sintering. Electron and thermal transport properties, i.e., electrical conductivity, carrier concentration, Hall mobility, Seebeck coefficient, and thermal conductivity, of CuI-Pb co-doped Bi₂Te₃ were measured in the temperature range from 300 K to 523 K and compared to corresponding x% of CuI-doped Bi₂Te₃ and undoped Bi₂Te₃. The addition of a small amount of Pb significantly decreased the carrier concentration, which could be attributed to the holes from Pb atoms, thus the CuI-Pb co-doped samples show a lower electrical conductivity and a higher Seebeck coefficient compared to CuI-doped samples with similar x values. The incorporation of Pb into CuI-doped Bi₂Te₃ rarely changed the power factor because of the trade-off relationship between the electrical conductivity and the Seebeck coefficient. The total thermal conductivity(κ_tot) of co-doped samples (κ_tot ~1.4 W/m∙K at 300 K) is slightly lower than that of 1% CuI-doped Bi₂Te₃ (κ_tot~1.5 W/m∙K at 300 K) and undoped Bi₂Te₃ (κ_tot ~1.6 W/m∙K at 300 K) due to the alloy scattering. The 1% CuI-Pb co-doped Bi₂Te₃ sample shows the highest ZT value of 0.96 at 370 K. All data on electrical and thermal transport properties suggest that the thermoelectric properties of Bi₂Te₃ and its operating temperature can be controlled by co-doping.

Data from Earth Observation (EO) satellites are increasingly used to monitor the environment, understand variability and change, inform evaluations of climate model forecasts and manage natural resources. Policy makers are progressively relying on the information derived from these datasets to make decisions on mitigating and adapting to climate change. These decisions should be evidence based, which requires confidence in derived products as well as the reference measurements used to calibrate, validate or inform product development. In support of the European Union’s Earth Observation Programmes Copernicus Climate Change Service, the Quality Assurance for Essential Climate Variables (QA4ECV) project fulfilled a gap in the delivery of climate quality satellite derived datasets by prototyping a robust, generic system for the implementation and evaluation of Quality Assurance (QA) measures for satellite-derived ECV climate data record products. The project demonstrated the QA system on six new long-term, climate quality ECV data records for surface Albedo, Leaf Area Index, FAPAR, NO₂, HCHO and CO. Provision of standardized QA information provides data users with evidence-based confidence in the products and enables judgement on the fitness-for-purpose of various ECV data products their specific applications.

To enable purposeful design and implementation of automated concrete technologies, precise assessment and prediction of the complex material flow at various stages of the process chain are necessary. This paper investigates the intermediate stage of the extrusion and deposition processes in extrusion-based 3D-concrete-printing, using a numerical model based on the Particle Finite Element Method (PFEM). In PFEM, due to the Lagrangian description of motion, remeshing algorithms and the alpha shape method are used to track the free surface during large deformation scenarios. The Bingham constitutive model was used for describing the rheological behaviour of fresh concrete. This model is validated by comparing the numerically predicted layer geometries with those obtained from laboratory 3D printing experiments. Extensive parametric studies were then conducted using the numerical simulation, delineating the influence of process and material parameters on the layer geometries, the dynamic surface forces generated under the extrusion nozzle and the inter-layer interactions.

The noble metals palladium and silver find use in many high performance applications, and their alloys (PdAg), known for more than sixty years, are industrially important, finding use in many fields including hydrogen purification and separation, numerous facets of catalysis, and in fuel cells. In recent years, interest in these materials has grown significantly, particularly in energy generating applications and due to their performance as solid-state chemical sensors for a range of small molecules. PdAg thin films can be prepared using traditional physical methods such as cold rolling, or more modern and controllable chemical or physical deposition techniques such as electrodeposition or chemical vapour deposition. Despite the wide-reaching uses of PdAg, several recent advancements in materials preparation, such as additive manufacturing, better known as 3-D printing, remain unexplored for this material due to the differing chemistries of the two elements. In this review, we explore the manufacturing methods commonly employed for the preparation of PdAg thin films, the common and niche applications of these materials, and opportunities for the future development of these two aspects, with an emphasis on how preparation of thin films can utilise additive manufacturing approaches.

This study describes the development of an automated bag valve mask (BVM) compression system, which, during acute shortages and supply chain disruptions can serve as a temporary emergency ventilator. The resuscitation system is based on the Arduino controller with a real-time operating system installed on a largely RepRap 3-D printable parametric component-based structure. The cost of the system is under $170, which makes it affordable for replication by makers around the world. The device provides a controlled breathing mode with tidal volumes from 100 to 800 milliliters, breathing rates from 5 to 40 breaths/minute, and inspiratory-to-expiratory ratio from 1:1 to 1:4. The system is designed for reliability and scalability of measurement circuits through the use of the serial peripheral interface and has the ability to connect additional hardware due to the object-oriented algorithmic approach. Experimental results demonstrate repeatability and accuracy exceeding human capabilities in BVM-based manual ventilation. Future work is necessary to further develop and test the system to make it acceptable for deployment outside of emergencies in clinical environments, however, the nature of the design is such that desired features are relatively easy to add with the test using protocols and parametric design files provided.

The aim of this study was synthesize and evaluate the effects of Poly (D, L-Lactide-co-glycolide) (PLGA) Nanoparticles (NPs) of metformin (PLGA+ Met) on inflammation, and bone loss in a ligature-induced periodontitis rat model. The prepared NPs were characterized by mean diameter, size particle, polydispensity index and encapsulation efficiency by Atomic force microscopy (AFM). Male albino Wistar rats were randomly divided into four groups of 20 rats in each group, and given the following treatments for 10 days to evaluate in vivo activity: (1) Sham: no ligature + water; (2) Positive control: ligature + water (with Periodontal disease and Diabetes); (3) ligature + PLGA+ 10 mg/kg Met (With Periodontal disease and Diabetes); and (4) ligature + PLGA+ 100 mg/kg Met (with Periodontal disease and Diabetes). Water or PLGA + Met was administered orally by gavage. Maxillae were fixed and scanned using Micro-computed Tomography (μCT) to quantify linear of bone loss. Histopathological characteristics were assessed through immunohistochemical staining for Osteocalcin, Cathepsyn K, RANKL/RANK/OPG pathway. IL-1β and TNF-α from gingival tissues were analysed by Elisa immunoassay. Quantitative RT-PCR reaction was used to evaluate gene expression of AMPK, NF-κB p-65, Hmgb1 and TAK-1 from gingival tissues. Statistical analysis was performed using one-way ANOVA at 5% significance. The mean diameter of MET-loaded PLGA nanoparticles was in a range of 457.1 ± 48.9 nm with a polydispersity index of 0.285, zeta potential: 8.16 ± 1.1 mV and entrapment efficiency (EE) was 70%. The results suggest that the addition of MET in the core slightly affected the particle sizes. Treatment with PLGA+ 10 mg/kg Met showed low inflammatory cells, decreased bone loss and integrity cement and levels of IL-1β, and TNF-α (p < 0.05) were significantly reduced. Additionally, weak staining was shown by RANKL, Cathepsyn K, OPG, and osteocalcin. Radiographically, linear measurements showed a statistically significant reduction in bone loss after treatment with PLGA+ 10 mg/kg Met compared to the positive control (p < 0.05). RT-PCR showed increased AMPK expression (p < 0.05) and decreased expression of NF-κB P65, HMGB1 and TAK-1 after PLGA+ 10 mg/kg Met (p < 0.05). The PLGA nanoparticle + 10 mg/kg Met decreased glucose levels and also decreased the inflammatory response, and bone loss in ligature-induced periodontitis in rats.

Within the past several decades, the emergence of new viral diseases with more severe health complications and mortality, primarily in older adults with comorbidities, is evidence of an age-dependent, compromised bodily response to abrupt stress with concomitant reduced immunity. The emergence of new infectious coronaviruses such as SARS-CoV-2 has resulted in the coronavirus disease 2019 (COVID-19). The result is increased morbidity and mortality in persons with underlying chronic diseases and among those with compromised defense mechanisms, regardless of age and among older adults who are more likely to fit these categories. COVID-19 appears to be primarily an upper respiratory disease. While SARS-CoV-2 is highly virulent, there is variability in the severity of the disease and its complications in humans. Severe pneumonia, acute respiratory distress syndrome (ARDS), lung fibrosis, cardiac t complication, acute kidney injury, hospitalization, and high mortality have been reported in older adults with COVID-19, that result from pathogen-host interactions. Here, we review potential interactions of the coronavirus and host cellular responses in relation to hallmarks of aging including genomic instability, telomere attrition, impaired autophagy, mitochondrial dysfunction, innate immunosenescence, inflammation and inflammasomes, adaptive immunosenescence, and epigenetic alterations, that likely contribute to the increased pathophysiological responses to SARS-CoV-2 among older adults.

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID-19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing the amount of relatively expensive UV resin, and iv) enabling production of handle on more accessible material extrusion 3-D printers. A modular open source UV LED box was designed, fabricated for $45 and tested for batch curing. Swabs can be fabricated for $0.06-$0.12/swab. The results of the mechanical validation tests showed that the swabs could withstand greater forces than would be expected in normal clinical use. The swabs were also able to absorb a significant amounts of synthetic mucus materials and passed abrasion and handling tests. The results show the open source swab are promising candidates for clinical trials.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

Dynamic thermogravimetric (TG) analysis under nitrogen environment was used to understand the thermal decomposition process of 3D printing filaments made of wood-filled polylactic acid (PLA)/starch blend. The characteristic temperatures and apparent activation energy (AAE) of the filaments with various starch contents were calculated with well-known kinetic models by Friedman, Flynn-Wall-Ozawa, Coats-Redfern and Kissinger. With the increased starch content in the filament, the onset thermal decomposition temperatures of the filaments decreased gradually from 272.4 to 155.1°C. The thermal degradation degree became smaller, and the transitional temperature interval became larger with increased starch proportion. The AAE values of the three types of filaments with different starch ratios varied between 97 kJ/mol and 114 kJ/mol, depending on material composition and method of calculation. The improved understanding of thermal decomposition behavior of PLA-starch-wood composites can help develop more biodegradable PLA/starch-based filaments for 3D printing.

Cu,N-TiO₂ nanotube (Cu,N-TNT) is prepared through a novel magnetron sputtering and anodic oxidation method. Then the morphology, structure and physicochemical property of Cu,N-TNT was analyzed by XRD, SEM, TEM, EDX and UV-vis-DR. The results indicate that the evenly doped copper is beneficial to the transformation of the TNT from anatase to rutile and play a key role in the morphology of the Cu,N-TNT. The doped Cu and N in the TNT influence the growth orientation of the TiO₂ crystals, which result in the lattice distortion and wider the interplanar spacing 60s-Cu,N-TNT has less band gap and stronger absorption intensity in visible region than other Cu,N-TNT samples, which make the combination rate of photogenerated electron and photogenerated hole decrease greatly, thus beneficial to its physicochemical property.

We describe the innate and adaptive immune system trajectory in Multi-system inflammatory syndrome of childhood (MIS-C), at acute(within 72 hours of hospitalization), resolution (at clinical improvement) and convalescent phase. In our cohort, in the acute phase, 68% of the children were SARS-CoV-2 seropositive, with hypercytokinenemia (high interleukin(IL)-1beta,IL-6,IL-8,IL-10,IL-17, interferon gamma), procoagulant state, myocardial dysfunction, activated neutrophils and monocytes; differential T and B cell subset lymphopenia; activated chemokine receptor type-7 positive and gamma-delta T cell subsets; antigen presenting cells had reduced HLA-DR expression; and B-cell class-switch responses occurred with illness resolution. MIS-C is an immunopathogenic illness associated with SARS-CoV-2 infections in children.

Although distributed additive manufacturing can provide high returns on investment the current markup on commercial filament over base polymers limits deployment. These cost barriers can be surmounted by eliminating the entire process of fusing filament by 3-D printing products directly from polymer granules. Fused granular fabrication (FGF) (or fused particle fabrication (FPF)) is being held back in part by the accessibility of low-cost pelletizers and choppers. An open-source 3-D printable invention disclosed here provides for precise controlled pelletizing of both single thermopolymers as well as composites for 3-D printing. The system is designed, built and tested for its ability to provide high tolerance thermopolymer pellets from a number of sizes capable of being used in a FGF printer. In addition, the chopping pelletizer is tested for its ability to chop multi-materials simultaneously for color mixing and composite fabrication as well as precise fractional measuring back to filament. The US$185 open-source 3-D printable pelletizer chopper system was successfully fabricated and has a 0.5 kg/hr throughput with one motor, and 1.0 kg/hr throughput with two motors using only 0.24 kWh/kg during the chopping process. Pellets were successfully printed directly via FGF and indirectly after being converted into high-tolerance filament in a recyclebot.

This paper investigates the effects of Inter-generational co-residence on health care market, and labor market outcomes, to see whether or not living under the same roof with at least one parent matters in health care market, and labor market behaviors in post-Affordable-Care Act (ACA) USA. The adopted analytical strategy involves not only looking at the gender differences in co-residence, and its effects on outcomes in the two markets, but also accounting for co-residence endogeneity following the recent literature. Unlike the recent literature that relies on instrumental variables methods, this study adopts a switching regression approach, defining inter-generational co-residence as an endogenous selection process using a binary probit equation, and modeled jointly with the extensive margins and intensive margins in the two markets. This novel approach results in a recursive trivariate probit model for each market, and estimated using penalized maximum likelihood methods. The results suggest that ACA by reorganizing the US health care market, seems to have reduced significantly disparities in health care access among males and females based on race, region of residence, place of birth, and citizenship. However not only do we observe significant differences in inter-generational co-residence status between males and females, we also find significant inequalities in the effects of co-residence on health care market, and labor market outcomes. In fact, co-residence is found to increase health care expenditure by 56.7% among females, while this figure increases to 74.2% among males. In addition co-residing individuals, while spending 69.7% more on health care annually are 1.22 times more likely to access health care, but 31% less likely to use health care intensively during the year. In the labor market, co-residence is found to reduce significantly hours of weekly labor supplied by 41% for females, and 55.6% for males. Furthermore co-residing individuals, while not significantly different in their likelihood of labor force participation, are 1.52 times less likely to work full time once they decide to participate, and also spend about 55.4% less time working in the labor market in post-ACA USA.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

This paper presents a comparison between indirect methods for assessing the buildability of 3D printed cementitious materials, including CRV or CSR test using rotational rheometry, unconfined uniaxial compression test (UUCT), a newly proposed confined uniaxial compression test (CUCT), and fast penetration test. The experimental program was conducted on the extruded samples of six printable mortars and two printable concretes with various rheological behavior achieved by the use of different additives and admixtures. Predictions of the material failure and the stability failure in hollow cylindrical structures are provided and compared with the results of the direct printing test. Benefits and disadvantages of the employed test methods are discussed, also taking into consideration a perspective of their use for automated in-situ control of the materials’ buildability.

Direct georeferencing of airborne pushbroom scanner data usually suffers from the limited precision of navigation sensors onboard of the aircraft. The bundle adjustment of images and orientation parameters, used to perform geocorrection of frame images during the post-processing phase, cannot be used for pushbroom cameras without difficulties: it relies on matching corresponding points between scan lines, which is not feasible in the absence of sufficient overlap and texture information. We address this georeferencing problem by equipping our aircraft with both a frame camera and a pushbroom scanner: the frame images and the navigation parameters measured by a couple GPS/Inertial Measurement Unit (IMU) are input to a bundle adjustment algorithm; the output orientation parameters are used to project the scan lines on a Digital Elevation Model (DEM) and on an orthophoto generated during the bundle adjustement step; using the image feature matching algorithm Speeded Up Robust Features (SURF), corresponding points between the image formed by the projected scan lines and the orthophoto are matched, and through a least-squares method, the boresight between the two cameras is estimated and included in the calculation of the projection; finally, using Particle Image Velocimetry (PIV) on the gradient image, the projection is deformed into a final image that fits the geometry of the orthophoto. We apply this algorithm to five test acquisitions over Lake Geneva region (Switzerland) and Lake Baikal region (Russia). The results are quantified in terms of Root Mean Square Error (RMSE) between matching points of the RGB orthophoto and the pushbroom projection. From a first projection where the Interior Orientation Parameters (IOP) are known with limited precision and the RMSE goes up to 41 pixels, our geocorrection estimates IOP, boresight and Exterior Orientation Parameters (EOP) and produces a new projection which RMSE with the reference orthophoto is around two pixels.

Nineteen million Americans have significant vision loss. Over 70% of these are not employed full-time, and more than a quarter live below the poverty line. Globally, there are 36 million blind people, but less than half use white canes or more costly commercial sensory substitutions. The quality of life for visually impaired people is hampered by the resultant lack of independence. To help alleviate these challenges this study reports on the development of a low-cost (<$24), open-source navigational support system to allow people with the lost vision to navigate, orient themselves in their surroundings and avoid obstacles when moving. The system can be largely made with digitally distributed manufacturing using low-cost 3-D printing/milling. It conveys point-distance information by utilizing the natural active sensing approach and modulates measurements into haptic feedback with various vibration patterns within the distance range of 3 m. The developed system allows people with lost vision to solve the primary tasks of navigation, orientation, and obstacle detection (>20 cm stationary, moving up to 0.5 m/s) to ensure their safety and mobility. Sighted blindfolded participants successfully demonstrated the device for eight primary everyday navigation and guidance tasks including indoor and outdoor navigation and avoiding collisions with other pedestrians.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

The dye effluent is usually difficult to be degraded by conventional wastewater treatment in leather industry. In order to develop efficient and cost-effective treatment methods, we evaluate the effect of white-rot fungus immobilization for dye decolorisation in this paper. The Phanerochaete chrysosporium BKM-F-1767 was used for immobilization. This research found that the white-rot fungus immobilization had an obviously decolorisation effect in dye wastewater treatment, and plant carriers such as sorghum stalk and corn cob were helpful to the growth of Phanerochaete chrysosporium in white-rot fungus immobilization. Due to the stability and recyclability, the white-rot fungus co-immobilization was considered as the most suitable treatment for decolorisation of dye effluent which enjoyed the advantages of both adsorption immobilization and entrapment immobilization. Furthermore, the dye decolorisation evaluation was carried out to find the most suitable carrier for co-immobilization, and it found that sorghum stalk - calcium-alginate gel spherical particle (SS-CGPB) has better decolorisation effect than corn cobs - calcium-alginate gel spherical particle (CC-CGPB), and the dye decolorisation rate was 86.77%. After 5 cycles, the dye decolorisation rate was 85.87% which indicated the SS-CGPB preserved functional integrity successfully. By further analyzing the biodegradation process with white-rot fungus immobilization, the intermediate products were observed and the degradation pathway of acid golden yellow dye molecular was proposed. The results showed that the C-N single bonds attached to the central benzene in the dye molecule were attacked and destroyed in white-rot fungus co-immobilization treatment, thus the structure of dye molecule could be successfully degraded into small molecules which would be more easily treated by conventional treatment methods. Therefore, the white rot fungus co-immobilization might be appropriate for pre-treatment as an important biotechnology for the advanced treatment of dye effluent.

It is well known that that there is an intrinsic link between the financial and energy sectors, which can be analyzed through their spillover effects, which are measures of how the shocks to returns in different assets affect each other’s subsequent volatility in both spot and futures markets. Financial derivatives, which are not only highly representative of the underlying indices, but can also be traded on both the spot and futures markets, include Exchange Traded Funds (ETFs), a tradable spot index whose aim is to replicate the return of an underlying benchmark index. When ETF futures are not available to examine spillover effects, “generated regressors” are useful for constructing both Financial ETF futures and Energy ETF futures. The purpose of the paper is to investigate the co-volatility spillovers within and across the US energy and financial sectors in both spot and futures markets, by using “generated regressors” and a multivariate conditional volatility model, namely Diagonal BEKK. The daily data used are from 1998/12/23 to 2016/4/22. The data set is analyzed in its entirety, and are also subdivided into three distinct subsets. The empirical results show there is a significant relationship between the Financial ETF and Energy ETF in the spot and futures markets. Therefore, financial and energy ETFs are suitable for constructing a financial portfolio from an optimal risk management perspective, and also for dynamic hedging purposes.

Contact-based co-culture of fibroblasts and keratinocytes is important to study the structure and functions of the wound bed. Co-culture of these two cell types in direct contact with each other has been challenging, requiring high serum concentrations (up to 10%), feeder systems and a range of supplemental factors. These approaches are not only technically demanding, but also present scientific, cost and ethical limitations associated with high-serum concentrations. We have developed two reduced-serum approaches (1-2%) to support contact-based co-culture of human dermal fibroblasts (HDFa) and human epidermal keratinocytes (HaCaT). The two approaches include (1) Specialized cell culture media for each cell type mixed in a 1:1 ratio (KGM+FGM), and (2) Minimal media supplemented with cell-specific growth factors (MEM+GF). Co-culture could be successfully achieved by co-seeding (two cell types were introduced simultaneously), or in a layered fashion (keratinocytes seeded on top of confluent fibroblasts). With wound scratch assays, the co-cultured platforms could demonstrate cell proliferation, migration and wound closure. The reduced-serum conditions developed are simple, easy to formulate and adopt, and based on commonly-available media components. These contact-based co-culture approaches can be leveraged for wound and skin studies, and tissue bioengineering applications, potentially reducing concerns with high-serum formulations.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser-wire based Directed Energy Deposition is demonstrated with a novel modification: site-specific changes to the controller set-point were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary 3D-printed component geometry. The present work shows that, through this technique, it is possible to print a specific geometry that occurs beyond the actual toolpath of the print head. This is denoted as an extra-toolpath geometry and is fundamentally different from other methods of generating component features in metal AM. A proof-of-principle experiment is presented in which a complex oak leaf geometry was embossed on an otherwise ordinary double-bead wall made from Ti-6Al-4V. The process is introduced and characterized primarily from a controls perspective with reports on the performance of the control system, the melt pool size response, and the resulting geometry. The implications of this capability, which extend beyond localized control of bead geometry to the potential mitigations of defects and functional grading of component properties, are discussed.

This paper introduces a closed-loop control strategy for maintaining consistency of liquid temperature in commercial Drop on Demand (DoD) inkjet printing. No additional sensors or additional actuators are installed in the printhead while achieving the consistency in liquid temperature. To this end, this paper presents a novel in situ sensing-actuation policy at every individual liquid-nozzle, where the jetting mechanism has three distinct roles. It is used for jetting liquid droplet onto the print media based on the print-job. It is used as a soft sensor to estimate the real-time liquid temperature of the jetting nozzle. While not jetting liquid, it is used as a heating actuator to minimize the gradient of liquid temperature among nozzles. The soft sensing based in situ controller is implemented in an experimentally validated digital twin that models the thermo-fluidic processes of the printhead. The digital twin is scalable and flexible to incorporate an arbitrary number of liquid-nozzles, making the control strategy applicable for future designs of the printhead.

This study reports on empirical findings of participatory design workshops for the development of a supportive user experience design system in the automotive. Identifying and addressing this area with traditional research methods is problematic due to the different UX design perspectives that might be conflicting and the related automotive domain limitations. To help resolve this problem, we conducted research with 12 User Experience (UX) designers through individual participatory prototyping activities to gain insights on their explicit, observable, tacit and latent needs. These activities allowed us to explore their motivation to use different technologies; the system's architecture; detailed features of interactivity and describe user needs including Efficiency, Effectiveness, Engagement, Naturalness, Ease of Use, Information retrieval, Self-Image awareness, Politeness, and Flexibility. Our analysis led us to design implications that translate participants' needs into UX design goals, informing practitioners on how to develop relevant systems further.

Crotoxin (CTX), the predominant toxin in Crotalus durissus terrificus snake venom (CdtV), has anti-inflammatory and immunomodulatory effects. Despite its inhibitory action on neutrophil migration and phagocytosis, CTX does not directly affect the production of reactive oxygen species (ROS) by the neutrophils. In contrast, it enhances the generation of reactive oxygen and nitrogen intermediates by macrophages. Given the importance of macrophage-neutrophil interactions in innate antimicrobial defense, the aim of this study was to investigate the effect of CTX on neutrophil ROS production and killing activity, either through CTX-treated macrophage co-culture or conditioned medium of CTX-treated macrophages. The results showed an important modulatory action of CTX on the neutrophil function as well as neutrophil-macrophage interactions, as demonstrated by the increased production of hydrogen peroxide, hypochlorous acid, nitric oxide and TNF-α, along with the increased fungicidal activity of neutrophils.

This study investigated whether biogas reactor performance, including microbial community development, in response to a change in substrate composition is influenced by initial inoculum source. Test reactors were first started with two different inocula and operated with the same grass-manure mixture for more than 120 days. These reactors initially showed great differences depending on inoculum source, but eventually showed similar performance and overall microbial community structure. At the start of the present experiment, the substrate was complemented with milled feed wheat, added all at once or divided into two portions. The starting hypothesis was that process performance depends on initial inoculum source and microbial diversity, and thus that reactor performance is influenced by the feeding regime. In response to the substrate change, all reactors showed increases and decreases in volumetric and specific methane production, respectively. However, specific methane yield and development of the microbial community showed differences related to initial inoculum source, confirming the hypothesis. The different feeding strategies had however only minor effects on process performance and overall community structure, but still induced differences in the cellulose-degrading community and in cellulose degradation.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

In the recent decade, Building Information Modelling (BIM) has widely been adopted in the Architecture, Engineering and Construction (AEC) industry and completely upended the way we build. While BIM continues gain momentum in the industry, it has also attracted increasing attentions from researchers. However, most of the current study focuses on reviewing BIM for management, BIM for green building, BIM for infrastructure and BIM for Facilities Management (FM). There are few studies about Global BIM review and to discuss their complex inter-connections. In this study, we adopted a scientometric analysis method to review global BIM research from 2004-2019. A total of 1455 scholarly bibliographic records obtained from Web of Science Core Collection databased were established for the analysis. This study has identified the top productive and influential researchers, research institutes, regions/countries, subject categories and journals in the BIM field. In addition, 11 clusters of Global BIM research were also identified including construction project, green BIM, construction safety planning, automated IFC-based workflow and so on. Authors distinguished 11 clusters of global BIM research into 3 stages, namely formulating stage, accelerating stage and transforming stage. Furthermore, authors reviewed the BIM policy of Singapore and observed there is a co-production relationship between evolution of BIM policy and global BIM research. These findings provide valuable information for researchers, practitioners and policy makers by visualizing the current progress in the research field of BIM and highlighting future research needs.

Avian infectious bronchitis virus (IBV) is the causative agent of infectious bronchitis, which causes considerable economic losses to the poultry industry worldwide. It is imperative to develop safe and efficient candidate vaccines to control IBV infection. In the current study, recombinant baculoviruses co-expressing S1 and N proteins, mono-expressing S1 or N proteins alone of IBV were constructed and prepared into subunit vaccines rHBM-S1-N, rHBM-S1 and rHBM-N. The levels of immune protection of these subunit vaccines were evaluated by inoculating specific pathogen-free (SPF) chickens at 14 days of age, boosting with the same dose 14 days later, and following challenge with a virulent GX-YL5 strain of IBV 14 days post-booster (dpb). The commercial vaccine strain H120 was used as a control. The IBV-specific antibody levels as well as the percentages of CD4+ and CD8+ T lymphocytes were detected within 28 days post-vaccination (dpv). The morbidity, mortality, and re-isolation of virus from the tracheas and kidneys of challenged birds were evaluated at 5 days post-challenge (dpc). The results showed that the IBV-specific antibody levels and the percentages of CD4+ and CD8+ T lymphocyte in rHBM-S1-N group were higher than those of rHBM-S1 and rHBM-N groups, especially the cellular immunity response. At 5 dpc, the mortality, morbidity and virus re-isolation rate of rHBM-S1-N were slightly higher than those of H120 group, but were lower than those of rHBM-S1 group and rHBM-N group. The present study demonstrated that the protection of recombinant baculovirus co-expressing S1 and N proteins was better than that of recombinant baculoviruses mono-expressing S1 or N protein alone. Thus, the recombinant baculovirus co-expressing S1 and N proteins could serve as a potential IBV vaccine and this demonstrates that the bivalent subunit vaccine including the S1 and N proteins might be a strategy for the development of an IBV subunit vaccine.

Simulation tools capturing the interactions of communication and electrical system operation represent a powerful support for fully assessing the potential benefits and impacts of ICT in future smart power distribution network. A strong interest is upon the possibility of exploiting the last generation communication systems for supporting the transition of distribution network towards a smart grid scenario. Having in mind the above, the authors propose a numerical co-simulation tool useful to thoroughly understand the impact of the communication networks on the performance of whole power system dynamics. The co-simulation tool has been purposely developed to simulate the highly time-critical smart grid application of fault management and network reconfiguration and permits reproducing and evaluating the behavior of the public mobile telecommunication system 4G Long Term Evolution (LTE), as communication technology for smart grid applications. Results of the paper demonstrates that LTE provides good performances for supporting the data communication required to perform fault location, extinction and a subsequent network reconfiguration in smart power distribution networks.

Ocean big data is the scientific practice of using big data technology in the marine field. Data from satellites, manned spacecraft, space stations, airship, unmanned aerial vehicles, shore-based radar and observation stations, exploration platforms, buoys, underwater gliders, submersibles, and submarine observation networks are seamlessly combined into the ocean’s big data. Increasing numbers of scholars have tried to fully analyze the ocean’s big data. To explore the key research technology knowledge graphs related to ocean big data, articles between 1990 and 2020 were collected from the “Web of Science”. By comparing bibliometric software and using the visualization software Cite-Space, the pivotal literature related to ocean big data, as well as countries, institutions, categories, and keywords, were visualized and recognized. Journal co-citation analysis networks can help determine the national distribution of core journals. Co-citation analysis networks for documents show authors who are influential at key technical levels. Key co-occurrence analysis network keywords can determine research hot spots and research frontiers. The three supporting elements of marine big data research are shown in the co-citation network. These elements are author, institution, and country. By examining the co-occurrence of keywords, the key technology research directions for future marine big data were determined.

The disruption of conventional manufacturing, supply, and distribution channels for medical supplies during the COVID-19 pandemic has caused widespread shortages and catalyzed local efforts to use nontraditional, rapid manufacturing to meet urgent healthcare needs. Here we present a crisis-responsive design framework designed to assist with product development under pandemic conditions. The framework utilizes extensive stakeholder engagement, comprehensive and dynamic needs assessment, local manufacturing, and product testing for the accelerated development of healthcare products. We contrast this framework with traditional medical device manufacturing and discuss relevant regulatory policies. We highlight the applicability of the crisis-responsive framework to a successful local program that designed and supplied face shields for a large US academic hospital. Finally, we make recommendations aimed at improving future resilience to healthcare emergencies. These include continued development of open source designs suitable for rapid manufacturing and changes in regulatory policy that strike a balance between rigidity and uncontrolled innovation.

Parts produced by laser or electron-beam powder bed fusion (PBF) additive manufacturing are prone to residual stresses, deformations, and other defects linked to non-uniform temperature distribution during the manufacturing process. Several researchers have highlighted the important role scan sequence plays in achieving uniform temperature distribution in PBF. However, scan sequence continues to be determined offline based on trial-and-error or heuristics, which are neither optimal nor generalizable. To address these weaknesses, we have articulated a vision for an intelligent online scan sequence optimization approach to achieve uniform temperature distribution, hence reduced residual stresses and deformations, in PBF using physics-based and data-driven thermal models. This paper proposes SmartScan, our first attempt towards achieving our vision using a simplified physics-based thermal model. The conduction and convection dynamics of a single layer of the PBF process are modeled using the finite difference method and radial basis functions. Using the model, the next best feature (e.g., stripe or island) that minimizes a thermal uniformity metric is found using control theory. Simulations and experiments involving laser marking of a stainless steel plate are used to demonstrate the effectiveness of SmartScan in comparison to existing heuristic scan sequences for stripe and island scan patterns. In experiments, SmartScan yields up to 43% improvement in average thermal uniformity and 47% reduction in deformations (i.e., warpage) compared to existing heuristic approaches. It is also shown to be robust, and computationally efficient enough for online implementation.

Degussa P25 is a benchmark form of TiO₂ used worldwide in photocatalysis studies. Currently no such benchmark exists for co-catalysts, which are essential for many photocatalytic reactions. Here, we present the preparation of Pt nanocluster co-catalysts on TiO₂ using an unmodified commercial source and equipment that is commonly available. Transmission electron microscopy reveals that the procedure produces TiO₂ decorated with Pt atom and nanoclusters (1-5 atoms). Optical reflectance and X-ray diffraction measurements show that the procedure does not affect the TiO₂ polymorph or UV-Vis absorbance. Gas phase photocatalytic splitting of heavy water (D₂O) shows that the Pt nanocluster decorated TiO₂ outperforms Pt nanoparticle (produced by photodeposition) decorated TiO₂ in D₂ production. Pt nanoclusters, produced directly from a commercial source, with high co-catalyst activity are prime candidates to be used in benchmark photocatalytic reactions.

Hormones must be balanced and dynamically controlled for the Female Reproductive Tract (FRT) to function correctly during the menstrual cycle, pregnancy, and delivery. Gamete selection and successful transfer to the uterus, where it implants and pregnancy occurs, is supported by the mucosal epithelial lining of the FRT ovaries, uterus, cervix, fallopian tubes, and vagina. Successful implantation and placentation in humans and other animals rely on complex interactions between the embryo and a receptive female reproductive system. The FRT's recent breakthroughs in three-dimensional (3D) organoid systems now provide critical experimental models that match the organ's physiological, functional, and anatomical characteristics in vitro. This article summarizes the current state of the art on organoids generated from various parts of the FRT. The current analysis examines recent developments in the creation of organoid models of reproductive organs, as well as their future directions.

This paper addresses pastoral resilience by drawing out the coping strategies and mechanisms utilized by the Maasai Pastoralists through a food system approach, based on the study findings of an anthropological study of pastoralism in Laikipia County, Rift Valley, Kenya. This paper is guided by the specific objectives aimed at establishing actors and their roles, and describing the institutional settings and changes in pastoralism. Using a new institutionalism approach, the paper focuses not only on the actors and their roles in pastoralism but also on how internal and external forces regulate access and use of common pool resources (CPRs) resulting in sustainability of the food system. We argue that this has an impact on the practice of pastoralism that continually defines and redefine the actors’ roles as well as elicit the value of pastoral economies and benefits accrued to a wide range of actors hence reinforcing pastoral resilience. The study also identified institutional settings and changes that lead to pastoral survival resulting from the country’s devolved system of governance. Data collection was through in-depth interviews, key informant interviews, focus group discussions and unstructured observations in the pastoral regions. The findings reveal that actors at the household, state, non-state, and service providers have developed varied coping strategies and mechanisms that sustain pastoralism. The study also identified institutional settings and changes that promote pastoral resilience; notably, private land ownership patterns, co-management of livestock markets, commercialization of herding, decentralization of livestock services, holistic management of pasturelands and the use of water-shed management plans. As a result, increased scholarship and advocacy in regards to the concept of co-management of livestock markets, is recommended as a means of understanding pastoral resilience that the food system exhibits.

Hydrogen is useful as a fuel and could be produced by a variety of means. One approach uses artificial photosynthesis where energy from sunlight powers the splitting of water into hydrogen and oxygen. But, biological methods for producing hydrogen has emerged strongly over the past decades. In particular, specific microorganisms could use different substrates to produce hydrogen at differing yields. Such fundamental discoveries with industrial applications thus motivated the use of metabolic engineering approaches and methodologies in enhancing biological hydrogen production through a series of enzyme over-expression, pathway debottlenecking, and gene deletion. However, such approaches heavily rely on the selection of an appropriate microbial chassis for biohydrogen production. With the proper strain in hand, use of alternative substrates may engender greater hydrogen productivities. But learning from the bioprocessing field, co-culture of two compatible microorganisms have been sought after for improving biohydrogen production. In addition, thermophilic microbes may also be useful candidates for exploiting hydrogen production from composting. Future outlook in the field looks into filling our gaps in understanding of the metabolic network that feeds into hydrogen production in different organisms. But, more importantly, problems such as reduced growth rate in engineered microbes point to fundamental issues with using genetically engineered microorganisms for improved biohydrogen production, to which clever bioprocess engineering may yield solutions.

The capacity of 3D printing (3DP) technologies to initiate speedy polymerization of solvent free resins accounts for their utility in the manufacturing of medical devices. Nonetheless, independent biological evaluation of 3D printed materials is recommended due to the unique parameters of the manufacturing process, which can influence their physical, chemical, and biological properties. In this study, E-Shell 450 material indicated for 3DP of hearing aid shells and inner ear devices was examined for biological safety using zebrafish bioassays adapted to OECD fish embryo test. In addition, the proprietary material was characterized for composition using headspace gas-chromatography mass spectrometry (GC-MS). To initiate test, newly fertilized zebrafish eggs were cultured on non-treated and ethanol-treated materials in glass petri dishes with ultrapure water, incubated at 28.5°C and assessed for developmental endpoints of toxicity at 24h interval until 96h. Data confirmed non-treated material was extremely toxic in bioassays within 24h whereas ethanol-treated material showed a relative lower toxicity possibly due to ethanoic-aqueous interactions as observed by GC-MS. With the current influx of 3D printing materials, users are urged to exercise caution. Operators must also take cognizance of the potential toxicity of the chemicals used in 3DP and implement safety measures to limit their exposure.

The war to technology and economic power have been the driver for industrialization in most developed countries. The first industrial revolution (industry 1.0) earned millions for textile mill owners while the second industrial revolution (industry 2.0) opened the way for tycoons and captains of industry like John D. Rockefeller, J.P. Morgan and Henry Ford. The third industrial revolution (industry 3.0) engendered technology giants like Apple and Microsoft, and made magnates of men like Steve Jobs and Bill Gates. Now, the race for the fourth industrial revolution (industry 4.0) is on and there is no option, every country whether developed or developing must participate. Many countries have positively responded to industry 4.0 by developing strategic initiatives to strengthen industry 4.0 implementation. Unlocking the country’s potential to industry 4.0 has been of interest to researchers in the recent past. However, the extent to which industry 4.0 initiatives being launched globally has never been revealed. Therefore, the present study aimed at exploring industry 4.0 initiatives through comprehensive electronic survey of literature to estimate the extend of its launching in different regions. Inferences were drawn from industry 4.0 initiatives in developed nations to be used as the recommendations for East Africa Community. Results of the survey revealed that 117 industry 4.0 initiatives have been launched in 56 countries worldwide consisting of five regions. The country’s percent of industry 4.0 initiatives as per region were: Latin America and the Caribbean (15%), North America (40%), Europe (53%), Asia and Oceania (25%), Middle East and Africa (11%). While the worldwide percent was estimated as 25%. This revealed that the big gap is existing between countries towards the race for industry 4.0.

Urban areas face daunting economic challenges that have increased in scope in recent years. At the same time, cities provide for opportunities for growth and value creation. The interplay of these challenges and opportunities represents the area of intervention for policymakers and researchers. However, the traditional approach to urban policy, deriving from the managerial and economic policy theories, shows difficulties mainly related to the capacity to counterbalance the interests and expectations of a multitude of stakeholders participating to the value co-creation process and to bring all different components to synergically contribute to the sustainability of the system. The Author proposes an innovative approach to urban public policy, by adopting the theoretical corpus of the Viable Systems Approach ("VSA"). Urban planning will be particularly analysed, as systemic components of urban areas, with the aim to investigate the decision-making processes for an integrated, efficient, effective and sustainable management of the territory as a multidimensional, multisectoral and multi-stakeholder entity. By recovering different settings, the VSA intends the co-creation of value as the capacity of the viable systems to increase its surviving chances in its own context. The value derives, first of all, from the strategic decisions aimed at finding both dyadic and context consonance. Through its strategic decisions, the Governing Body of the territory develops a specific system as the overall synthesis of all possible systems organised within a specific area, identifying pattern of development agreed by the several stakeholders of the territory. In the dynamics of value co-creation in systemic multi-subjective organizations, where the level of complexity is particularly significant, the research for consonance among different stakeholders is particular important in order to achieve the most value for the territory. In this respect, the VSA may constitute a valid tool, helping to find the necessary capacities to imagine evolutionary paths towards new competencies.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

With the progress of immunotherapy in cancer, oncolytic viruses (OVs) are getting more and more attention during the past decade. Due to their cancer-selective and immunogenic property, OVs are considered ideal candidates to be combined with immunotherapy to increase both specificity and efficacy in cancer treatment. OVs preferentially replicate in and lyse cancer cells, generating pathogen-associated molecular patterns (PAMPs) and danger (damage)-associated molecular patterns (DAMPs). These signals trigger innate immune response to modulate the solid tumor microenvironment, resulting in in situ autovaccination leading to adaptive anti-virus and anti-tumor immunity. Here, we summarize the conceptual updates of oncolytic virotherapy, immunotherapy, and the strategies to enhance the virus-mediated anti-tumor immune response, including: 1. Arm OVs with cytokines to modulated innate and adaptive immunity; 2. Combine OVs with immune checkpoint inhibitors to release T cell inhibition; 3. Combine OVs with immune co-stimulators to enhance T cell activation.

Most of the phase change materials (PCMs) have been limited to use as functional additions or sealed in containers, and extra auxiliary equipment or supporting matrix is needed. The emergence of 3D printing technique has dramatically advanced the developments of materials and simplified production processes. This study focuses on a novel strategy to model thermal energy storage crystalline gels with three-dimensional architecture directly from liquid resin without supporting materials through light-induced polymerization 3D printing technique. A mask-projection stereolithography printer was used to measure the 3D printing test, and the printable characters of crystalline thermal energy storage P(SA-DMAA) gels with different molar ratios were evaluated. For the P(SA-DMMA) gels with small fraction of SA, the 3D fabrication was realized with higher printing precision both on mili- and micro-meter scales. As a comparison of 3D printed samples, P(SA-DMAA) gels made by other two methods, post-UV curing treatment after 3D printing and UV curing using conventional mold, were prepared. The 3D printed P(SA-DMAA) gels shown high crystallinity. Post–UV curing treatment was beneficial to full curing of 3D printed gels, but did not lead to the further improvement of crystal structure to get higher crystallinity. The P(SA-DMAA) crystalline gel having the highest energy storage enthalpy that reached 69.6 J·g⁻¹ was developed. Its good thermoregulation property in the temperature range from 25 to 40 °C was proved. The P(SA-DMAA) gels are feasible for practical applications as one kind of 3D printing material with thermal energy storage and thermoregulation functionality.

Biocompatible and biodegradable poly(butylene succinate-co-adipate) (PBSA)/hexadecylamine-modified PPZn (m-PPZn) nanocomposites were prepared using a melt mixing process. Experimental results of wide-angle X-ray diffraction and transmission electron microscopy revealed that the stacking layers of the m-PPZn were partially intercalated and partially exfoliated into the PBSA polymer matrix. The isothermal crystallization kinetics of PBSA/m-PPZn nanocomposites were studied at the temperature range of 62−70 °C and the half-time for crystallization of 3 wt % PBSA/m-PPZn nanocomposite was reduced by 27−35% compared with that of pure PBSA. This finding suggests that the incorporation of m-PPZn might cause the heterogeneous nucleation and the subsequent crystallization growth, which enhances the isothermal crystallization rate of PBSA/m-PPZn nanocomposite. The biodegradation rates of PBSA using Lipase from Pseudomonas sp. increase as the contents of m-PPZn increase. The degradation behavior of the neat PBSA investigated using the change of weight-average molecular weight belongs to exo-type hydrolysis activity. It is necessary to point out that the change of degree of crystallinity and degradation rate are almost linearly proportional to the loading of hexadecylamine-modified PPZn. This finding would provide an important information for the manufacturing biodegradable PBSA nanocomposites.

3D-printing with foam concrete, which is known for its distinct physical and mechanical properties, has not yet been purposefully investigated. The article at hand presents a methodological approach for the mixture design of 3D-printable foam concretes and a systematic investigation of the potential application of this type of material in digital construction. Three different foam concrete compositions with water-to-binder ratios between 0.33 and 0.36 and having densities of 1100 to 1580 kg/m³ in the fresh state were produced with a pre-foaming technique using a protein-based foaming agent. Based on the fresh-state tests, including 3D-printing as such, an optimum composition was identified and its compressive and flexural strengths were characterised. The printable foam concrete showed compressive strength above 10 MPa and low thermal conductivity, which make it suitable for 3D-printing applications, while fulfilling both load-carrying and insulating functions.