Elastic yarns are the key component of high-performance compression garments. However, it remains a challenge to fabricate anti-fatigue yarns with high mechanical force and long elongation for generating compression garments with prolonged wear. In this paper, we report the development of anti-fatigue double-wrapped yarns with excellent mechanical properties by wrapping high-denier Spandex with nylon filaments in opposite twists. In particular, 560D high-denier Spandex as the core was untwisted which can maximumly reduce the interaction between the core and wrapping filaments, enabling high elongation of the double-wrapped yarns. In addition, we chose 70D nylon filaments with a tensile force of 387.40 ± 8.82 cN as the wrapping materials to provide sufficient force for double-wrapped yarns. Notably, opposite twists were induced for the inner and outer wrapping filaments to achieve a balanced stable yarn structure. By systematically optimizing manufacturing parameters including inner wrapping density, outer wrapping density, taking-up ratio, and drafting ratio, we obtained double-wrapped yarn with excellent tensile force (952.00 ± 24.03 cN) and elongation (357.28% ± 9.10%). Notably, the stress decay rate of optimized yarns was only 12.0% ± 2.2%. In addition, the optimized yarn was used as the weft-lining yarn for generating weft-lined fabrics, the elastic recovery rate of the obtained fabric was only 2.6% after cyclic stretching, much lower than the control fabric. Our design of anti-fatigue double-wrapped yarns could be widely used for fabricating high-performance compression garments.

Quinoa, known as the "golden grain" for its high nutritional value, is a significant source of essential nutrients, including proteins, minerals, vitamins, polyphenols, phytosterols, and flavonoids. However, the biological functions of quinoa polysaccharides remain understudied. In this research, two crude quinoa polysaccharides extracts (Q-40 and Q-60) were obtained extracting by 40% and 60% alcohol. The purity of Q-40 and Q-60 was 58.29% and 62.15%, with protein contents of 8.27% and 9.60%, respectively. Monosaccharide analysis revealed that Q-40 contained glucose (Glc), galacturonic acid (GalA), and arabinose (Ara) in a molar ratio of 0.967:0.027:0.006. Q-60 was composed of xylose (xyl), arabinose (Ara), galactose, and galacturonic acid (GalA) with a molar ratio of 0.889:0.036:0.034:0.020. The average molecular weight of Q-40 ranged from 47484 to 626488 Da, while Q-60 showed a range of 10025 to 47990 Da. Rheological experiments showed that Q-40 exhibited higher viscosity, while Q-60 demonstrated more elastic properties. Remarkably, Q-60 showed potent antioxidant abilities, with scavenging rates of 98.49% for DPPH and 57.5% for ABTS. Antibacterial experiments using the microdilution method revealed that Q-40 inhibited the growth of Methicillin-resistant Staphylococcus aureus (MRSA) and E. coli, while Q-60 specifically inhibited MRSA. At lower concentrations, both polysaccharides inhibited MDA cell proliferation, but at higher concentrations, they promoted proliferation. Similar proliferation-promoting effects were observed in HepG2 cells. The research provides important information in application of quinoa in food and functional food industries.

The current study assessed the influence of Anti Stripping Agents (ASA), Ground Tire Rubber (GTR) and waste polyethylene terephthalate (PET) on performance behavior of binder and Stone Matrix Asphalt (SMA) mixtures. Through this paper, the 85/100 penetration grade bitumen was utilized as original bitumen. Also, three liquid ASA’s (ASA (A), ASA (B), ASA (C)) were used as a mixture modifier. For this purpose, softening point, penetration, rotational viscosity, Dynamic Shear Rheometer, Multi Stress Creep Recovery (MSCR) and Linear Amplitude Sweep (LAS) tests were implemented to investigate the rheological properties of modified bitumen. For evaluating the behavior of modified mixtures several tests such as; Resilient Modulus, Tensile Strength, dynamic creep, wheel track and four-point beam fatigue tests were implemented. Based on MSCR test results, utilization of mentioned polymers enhanced the elasticity of bitumens and therefore the permanent deformation resistance of binders increases. Also by the addition of PET percentage, the rutting resistance improves. Results indicated that utilization of ASAs, PET and Crumb Rubber (CR) enhance the Resilient Modulus (Mr), Indirect Tensile Strength (ITS), rutting resistance, fatigue life and Fracture Energy (FE) of asphalt mixtures. Also based on results, modification of binder by PET/CR with a ratio of 50%/50% and ASA (B) have the highest fatigue life which indicates that this mixture has highest resistance against fatigue cracking.

Objective: The study aimed to evaluate the effects of monoclonal antibodies (mAbs) acting on the calcitonin gene-related peptide (CGRP) or its receptor (anti-CGRP/R mAbs) on comorbid symptoms of depression, anxiety, and fatigue in migraine patients resistant to traditional prophylaxis. Methods: The study was an open-label prospective study assessing comorbidities in patients with high frequency (HFEM) and chronic migraine (CM), medication overuse headache (MOH), and resistance to traditional prophylaxis treated with anti-CGRP/R mAbs for 3 months. Results: 77 patients were enrolled with either HFEM (21%) or CM (79%) with or without MOH (56% and 44% respectively). We identified 21 non-responders (27%) and 56 responders (73%), defined on the reduction ≥ 50% of headache frequency. The two groups were highly homogeneous for investigated comorbidities. Disease severity in terms of headache frequency, migraine-related disability, and affective comorbid symptoms were reduced in both groups with different thresholds; allodynia and fatigue were ameliorated only in responders. Conclusion: anti-CGRP/R antibodies improve pain together with affection, fatigue, and sensory sensitization in migraine patients.

The effect of defects and microstructure on mechanical properties of Ti-6Al-4V welds produced by tungsten inert gas welding, plasma arc welding, electron beam welding and laser beam welding was studied in the present work. The mechanical properties of the different weld types have been evaluated with respect to micro hardness, yield strength, ultimate tensile strength, ductility and fatigue at room temperature and at elevated temperature. Metallographic investigation was carried out to characterize the microstructures of different weld types and fractographic investigation to relate the effect of defects on fatigue performance. Electron and laser beam welding produced welds with finer microstructure, higher tensile ductility and better fatigue performance than tungsten inert gas welding and plasma arc welding. Large pores and pores located close to the specimen surface were found to be most detrimental to fatigue life.

The influence of the austempering temperatures on the microstructure and mechanical properties of austempered ductile cast iron (ADI) was investigated. ADI is nodular graphite cast iron, which owing to higher strength and elongation exceeds mechanical properties of conventional spheroidal graphite cast iron. Such a combination of properties is achieved by the heat treatment through austenitization, followed by austempering at different temperatures. The austenitization conditions were the same for all the samples: temperature 890°C, duration 30min, and quenching in a salt bath. The main focus of this research was on the influence of the austempering temperatures (270°C, 300°C, and 330 C) on the microstructure evolution, elongation, toughness and fatigue resistance of ADI modified by certain amount of Ni, Cu, and Mo. The Vickers and Rockwell hardness decreased from 535.7 to 405.3HV/1 (55.7 to 44.5HRC) as the austempering temperature increased. Optical images showed the formation of graphite nodules and matrix composed of ausferrite; the presence of these phases was confirmed by an XRD diffraction pattern. A fracture surface analysis revealed several types of the mechanisms: cleavage ductile, transgranular and ductile dimple fracture. The stress-controlled mechanical fatigue experiments revealed that a 330°C austempering temperature ensures the highest fatigue life of ADI.

Since ancient times, various scientists and doctors have utilized different herbs to heal diseases. Due to the rise in drug resistance and the negative effects of chemosynthetic drugs, researchers and the general public around the world have become more interested in medicinal herbs and plant metabolites/extracts. This is due to its non-toxicity and several health benefits when used to treat diseases in clinical and medical settings. Ocimum basilicum is one such plant, possessing a wide range of bioactive phytochemicals including alkaloids, phenolics, flavonoids, tannins, saponins, reducing sugars, cardiac glycosides, steroids and glycosides, as well as complex pharmacological activities including anti-inflammatory, antifungal, antibacterial, antioxidant, wound healing and antiviral properties. The results of many studies on Ocimum basilicum plant extracts are collected and presented in this review. The plant extracts have an excellent potential to be used as medicinal raw materials and exhibit an extensive variety of therapeutic capacities, including antibacterial, antioxidant, wound healing, anti-inflammatory, antifungal, and antiviral properties.

A (2,6)-fullerene F is a 2-connected cubic planar graph whose faces are only 2-length and 6-length. Furthermore, it consists of exactly three 2-length faces by Euler's formula. The (2,6)-fullerene comes from Do\v{s}li\'{c}'s (k,6)-fullerene, a 2-connected 3-regular plane graph with only k-length faces and hexagons. Do\v{s}li\'{c} showed that the (k,6)-fullerenes only exist for k = 2, 3, 4 or 5, and some of the structural properties of (k,6)-fullerene for k = 3, 4 or 5 are studied. In this paper, we study the properties of (2,6)-fullerene. We obtain that the edge-connectivity of (2,6)-fullerenes is 2. Every (2,6)-fullerene is 1-extendable, but not 2-extendable. F is said to be k- resonant (k>0) if the deleting of any i (0=< i<= k) disjoint even faces of F results in a graph with at least one perfect matching. We have that every (2,6)-fullerene is 1-resonant. An edge set S of F is called an anti-Kekule set if F-S is connected and has no perfect matchings, where F-S denotes the subgraph obtained by deleting all edges in S from F. The anti-Kekule number of F, denoted by ak(F), is the cardinality of a smallest anti-Kekule set of F. We have that every (2,6)-fullerene F with |V(F)|>6 has anti-Kekule number 4. Further we mainly prove that there exists a (2,6)-fullerene F having f_{F} hexagonal faces, where f_{F} is related to the two parameters n, m.

For successful reuse of old asphalt as reclaimed asphalt pavement (RAP) added to new bituminous mixtures it is necessary to improve some of its properties. This can be attained, for example, by adding an appropriate rejuvenating agent. The aim of this study was to evaluate the properties of a lab aged 35/50 pen grade bitumen, rejuvenated by addition of two varieties of rapeseed imidazo-line. Both short-term and long-term ageing were simulated using the Rolling Thin Film Oven Test (RTFOT) and Pressure Ageing Vessel (PAV), i.e. standard lab ageing methods. The first step in-cluded determination of the basic properties of the analysed pen grade bitumen. Fatigue cracking resistance of the bitumen was checked as the next step. The dynamic shear rheometer (DSR) test was carried out for this purpose, at the intermediate operating temperature of road pavements. The obtained data were then used to calculate the fatigue cracking critical temperature (FCCT). A ductility test was also carried out in a ductilometer, in which the applied tensile force was meas-ured. The obtained results demonstrated a beneficial effect of rapeseed imidazoline on the prop-erties of the tested pen grade bitumen after ageing, when added at a rate of 6% and more.

The oceans harbor a great diversity of organisms, and have been recognized as an important source of new compounds with nutritional and therapeutic potential. Among these compounds, carbohydrate-based compounds are of particular interest because they exhibit numerous biological functions associated with their chemical diversity. This gives rise to new substances for the development of bioactive products. Many are the known applications of substances with glycosidic domains obtained from marine species. This review covers the structural properties and the current findings on the antioxidant, anti-inflammatory, anticoagulant, antitumor and antimicrobial activities of medium and high molecular-weight carbohydrates or glycosylated compounds extracted from various marine organisms.

Chaenomeles plants are adapted to diverse ecological zones particularly the temperate areas of Korea, Japan and China. In China, Chaenomeles speciosa mainly planted in Chongqing, Anhui and Hubei provinces. Most of the studies till date have been focused on the anti-inflammatory activities of C. speciosa fractions. The present study aimed to review the maximum literature reported for the presence of various phytochemicals in C. speciosa. In addition, the pharmacological properties of these chemical compounds of this plant shall also be discussed. The extracts of the various parts of the plant are rich in diversity of antioxidants, organic acids, phenolics, terpenoides and many different phytochemicals that bear strong anticancer, antioxidant, anti-viral, antibacterial properties, anti-inflammation, anti-hyperlipidemic, anti-hyperglycemic and anti-parkinson properties. C. speciosa fruits have broad scope in industry as well as in medicines. Not only the leaves and fruits of C. speciosa plant, but various other parts including roots, seeds, bark twigs, and flowers all have long history of clinical trials in curing many human ailments. However, the maximum accessible data concerning the chemical composition and their broad pharmacological properties of C. speciosa plant parts is pretty restricted that make it more appealing for indepth investigations.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

Food and drinks can be contaminated with pollutants such as lead and strontium and this poses a serious danger to human health. For this reason, a number of effective sensors have been developed for the rapid and highly selective detection of such contaminants. TBA, a well-known aptamer developed to selectively target and thereby inhibit the protein of clinical interest -thrombin, is receiving increasing attention for sensing applications, particularly for the sensing of different cations. Indeed, TBA, in the presence of these cations, folds into the stable G-quadruplex structure. Furthermore, different cations produce small but significant changes in this structure that result in changes in the electrical responses that TBA can produce. In this article we produce an overview of the expected data regarding the use of TBA in the detection of lead and strontium, calculating the expected electrical response using different measurement techniques. Finally, we conclude that the TBA should perform better as a detector of strontium rather than lead.

Diabetes mellitus remains a major risk factor for developing cardiovascular diseases, resulting in increased morbidity and mortality associated with cardiovascular complications. Given the burden of diabetes-related cardiovascular complications, there is a need to identify strategies, safe and effective therapeutic agents that could effectively prevent and control diabetes. Presently, many patients living with diabetes depends on traditional medicines as an alternative cure. Channa striatus (Haruan) is a freshwater fish traditionally used to treat wounds, inflammations, and pains. Several pharmacological investigations have supported the folkloric claims of C. striatus extracts, including hypoglycemic, hypolipidemic, antioxidant, anti-inflammatory, and pro-platelet aggregation activities. The therapeutic potentials of C. striatus were demonstrated to be associated with the presence of high content essential amino acids and good fatty acids known to improve cell growth and facilitate wound healing. Therefore, C. striatus bioactive compounds have great potentials to serve as lead candidates in developing novel therapeutic agents for the management of diabetes and related cardiovascular diseases. This review aims to provide a comprehensive overview of the pharmacological properties and therapeutic potentials of C. striatus for the management of diabetes and associated cardiovascular complications.

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries have been tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance have been determined. Results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with previous studies results, to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

Cherries have been largely investigated due to their high content in phenolics in order to fully ex-plore their health-promoting properties. Therefore, this work aimed to assess, for the first time, the anti-inflammatory potential of phenolic-targeted fractions of Saco cherry, using RAW 264.7 mac-rophages stimulated with lipopolysaccharide. Additionally, the cytotoxic effects on gastric ade-nocarcinoma (AGS), neuroblastoma (SH-SY5Y) and normal human dermal fibroblast (NHDF) cells were evaluated, as well as the ability to protect these cellular models against induced oxidative stress. The obtained data revealed that cherry fractions can interfere with cellular nitric oxide (NO) levels by capturing NO radicals and decreasing inducible nitric oxide synthase and cyclooxygen-ase-2 expression. Furthermore, it was observed that all cherry fractions exhibited dose-dependent cytotoxicity against AGS cells, presenting cytotoxic selectivity for these cancer cells when compared to SH-SY5Y and NHDF cells. Regarding their capacity to protect cancer cells against oxidative injury, in most assays, the total cherry extract was the most effective. Overall, this study reinforces the sweet cherries incorporation in new pharmaceutical products, smart foods and nutraceuticals.

in this work formulations of "environmentally compatible" silicone-based antifouling synthesized in the laboratory and based on copper and silver on silica/titania oxides have been characterized, capable of replacing the non-ecological antifouling paints currently on the market. The texture properties and the morphological analysis of these powders with an antifouling action indicate that their activity is linked to the nanometric size of the particles and to the homogeneous dispersion of the metal on the substrate. The presence of two metal species on the same support limits the for-mation of nanometric species and therefore the formation of homogeneous compounds. The presence of the antifouling filler (specifically the one based on TiO2 and Ag) facilitates the achievement of a higher degree of cross-linking of the pure resin, and therefore a better compactness and completeness of the coating. This leads to a consequent better degree of adhesion to the tie-coat and therefore to the steel support used for the construction of the boats.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

Sesamum indicum is considered an underutilized oil-bearing seed in the semi-arid regions of Ghana. Nonetheless, it is a promising source of food with both nutritional and therapeutic benefits. The aim of the present study was to evaluate the antioxidant properties S. indicum seeds using different extraction solvents. The seeds were obtained from the local farmers and prepared for analysis. The bioactive compounds present in the seeds were extracted using hexane, ethyl acetate, ethanol and water and their yields quantified. Total phenolic content (TPC), Condensed tannin content (TTC) and Total antioxidant capacity (TAC) , and DPPH radical scaveging assay were analyzed using standard methods. Antinutrients such as saponins, alkaloids, phytates and oxalates were also analyzed from the powdered seeds. Two chemometric methods; hierarchical cluster analysis (HCA) and Pearson correlation were employed to evaluate the interdependence of the various parameters to result in their antioxidant properties. The re-sults revealed that the solvents utilized had a significant impact on the extraction yield, phyto-chemical component concentration, and antioxidant activities. Hexane extracts of S. indicum seeds significantly exhibited the highest antioxidant activity (p &lt; 0.05). It was marked with the highest TAC value of 232.6 ± 6.267 mg/g AAE and a strong DPPH scavenging activity with an IC50 of 52.81 ± 2.30 µg/mL. Correlations (p &lt; 0.05) was established between TPC,CTC, TAC and DPPH radical scavenging activity) of the extracts. Antinutrients such as; phytate, oxalate, saponins and alkaloids were found to be 7.691 ± 0.8576, 1.501 ± 0.1375, 21.33 ± 4.619 and 317.33 ± 30.29 mg/g respectively. Data obtained suggest that S. indicum possess rich bioactive compounds that can be used in neutraceuticals and food products.

The application of instrumented indentation to assess material properties like Young’s modulus and micro-hardness has become a standard method. In recent developments, indentation experiments and simulations have been combined to inverse methods, from which further material parameters as yield strength, work hardening rate, and tensile strength can be determined. In this work, an inverse method is introduced by which material parameters for cyclic plasticity, i.e. kinematic hardening parameters, can be determined. To accomplish this, cyclic Vickers indentation experiments are combined with finite element simulations of the indentation with unknown material properties, which are then determined by inverse analysis. To validate the proposed method, these parameters are subsequently applied to predict the uniaxial stress-strain response of a material with success. The method has been validated successfully for a quenched and tempered martensitic steel and for technically pure copper, where an excellent agreement between measured and predicted cyclic stress-strain-curves has been achieved. Hence, the proposed inverse method based on cyclic nanoindentation, as a quasi-non-destructive method, could complement or even substitute the resource-intensive conventional fatigue testing in the future for some applications.

Antisense oligonucleotides (ASONs) have proven potential for the treatment of various diseases. However, their limited bioavailability restricts their clinical application. New structures with improved enzyme resistance stability and efficient drug delivery are needed. In this work, we propose a novel category of ASONs bearing anisamide conjugation at phosphorothioate sites for oncotherapy. ASONs can be conjugated with the ligand anisamide very efficiently and flexibly in solution. The conjugation sites and ligand amount both influence anti-enzymatic stability and cellular uptake, resulting in changes in antitumor activity that are detectable by cytotoxicity assay. T6 (with double end AA-conjugation) was identified as the optimal conjugate, and its antitumor activity and the underlying mechanism were examined further in vitro and in vivo. This paper presents a new strategy for the design of nucleic acid–based therapeutics with improved drug delivery and biophysical and biological efficacy.

In this review paper, the latest literature on the functional properties of phospholipids in relation to inflammation and inflammation-related disorders has been critically appraised and evaluated. The paper is divided into three sections: Section one addresses the relationship between the anti-inflammatory bioactivities of different phospholipids in relation to their structures and compositions. Sections two and three are dedicated to the structures, functions and anti-inflammatory properties of dietary phospholipids from animal and marine sources. Most of the dietary phospholipids of animal origin come from meat, egg and dairy products. To date, there is very limited work published on meat phospholipids, undoubtedly due to the negative perception that meat consumption is an unhealthy option due to its putative associations with several chronic diseases. These assumptions are addressed with respect to the phospholipid composition of meat products. Recent research trends indicate that dairy phospholipids possess anti-inflammatory properties, which has led to an increased interest into their molecular structures and reputed health benefits. Finally, the structural composition of phospholipids of marine origin is discussed. Extensive research has been published in relation to ω-3 polyunsaturated fatty acids (PUFAs) and inflammation, however this research has recently come under scrutiny and has proved to be unreliable and controversial in terms of the therapeutic effects of ω-3 PUFA, which are generally in the form of triglycerides and esters. Therefore, this review focuses on recent publications concerning marine phospholipids and their structural composition and related health benefits. Finally, the strong nutritional value of dietary phospholipids are highlighted with respect to marine and animal origin and avenues for future research are discussed.

The purpose of the present study was to evaluate the antioxidant activity and peptide levels of Feta cheese and other brined cheeses, and Metsovone cheese, and other smoked cheeses. The antioxidant activity was determined by Folin and FRAP assays, while the peptide content was determined by Bradford and Lowry assays. The assays were applied in the water soluble extract of cheeses. The results showed that Feta cheese and brined cow cheese differ in antioxidant activity. Feta cheese and brined goat cheese also differ in both antioxidant activity and peptide levels. Results also showed that Metsovone cheese and other smoked cheeses exhibit antioxidant activity and significant peptide levels. Moreover, the water soluble extracts of all cheeses show some anti-inflammatory activity, suggesting that may peptides exhibit anti-inflammatory activity.

Laser additively manufactured (LAM) Ti–6Al–4V alloy has huge application potential in aerospace structural parts such as turbine blades. However, there are few studies on the fatigue properties of such LAM parts under vibration loading, particularly with regard to anisotropy. In this paper, vibration fatigue properties of LAM Ti-6Al-4V by laser melted deposition process were investigated along the transversely deposited (TD) direction and parallelly deposited (PD) direction. Through the first-order bending vibration experiments, LAM Ti-6Al-4V alloy exhibits obvious anisotropic fatigue properties and significant dispersion in fracture position. The fracture morphology analysis reveals that the vibration fatigue failure was mainly dominated by the LAM process-induced defects and the microstructure. For the LAM samples without defects at crack initiation sites, the fatigue behavior is controlled by the prior β columnar grains with preferential orientation, which leads to enhanced fatigue crack propagation resistance for the PD samples. For the LAM samples with defects at initiation sites, having lower fatigue lives, the fatigue anisotropy strongly depends on the projection area of the lack-of-fusion defects relative to the loading direction, resulting in better fatigue performance for the TD samples.

Owing to fascinating applications of ZnO in modern devices, it is interesting to explore its more features for future devices. Hence, herein, we have synthesized the high quality ZnO spherical nanoparticles (SNPs) through a facile green synthesis route and robust structural and biomedical studies are carried out. Hexagonal phase with 93.2% crystallinity was confirmed through XRD analysis. ZnO nanoparticles were tested for their bioactivities both in vivo (acute cytotoxicity test) and in vitro (Anti-cancer activities on liver (HepG2) and cervical (Hela) cancer cell lines, stimulatory/inhibitory effects on normal rat splenic cells and hemolytic effects on red blood cells). Results showed that ZnO SNPs has no cytotoxic effects on vital organ like liver and has no hemolytic action on red blood cells. ZnO SNPs showed inhibitory consequence on normal rat splenic cells growth at all tested concentrations. ZnO nanoparticles showed an inhibitory effect on HepG2 cell line. While showed stimulatory effect on Hela cell line. Current study presents the synthesized ZnO SNPs as highly applicable in bio-optoelectronics.

Development of the self-cleaning and anti-fogging superhydrophobic coating for aluminum surfaces which is durable in the aggressive conditions has raised tremendous interest in materials science. In this work, by employing chemical etching technique with mixture of hydrochloric and nitric acid, followed by passivation with lauric acid, superhydrophobic aluminum surface was synthesized. The surface morphology analysis reveals the presence of rough microstructures on coated aluminium surface. Superhydrophobicity with water contact angle of 170 ± 3.9° and sliding angle of 4 ± 0.5° is achieved. Surface bounces off the high speed water jet, indicating excellent water-repellent nature of coating. It is also continuously floated on water surface for several weeks, showing excellent buoyancy nature. Additionally, coating maintains its superhydrophobicity after undergoing 100 cycles of adhesive tape peeling test. Its superhydrophobic nature withstands 90° and 180° bending, and repeated folding and de-folding. Coating exhibits the excellent self-cleaning property. In low temperature condensation test, almost no accumulation of water drops on the surface, showing the excellent anti-fogging property of coating. This approach can be applied to any size and shape of aluminium surface and hence has great industrial applications.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

The Kalanchoe genus is composed of more than 100 species that usually thrive in tropical environments, which have been used in folkloric medicine to treat various illnesses, including dermatological conditions. With this, the present study assesses the pharmacognostical and pharmacological properties of different species of the Kalanchoe genus as elements for a potential treatment for dermatological-related conditions, from findings of existing literature and studies. It was analyzed that the Kalanchoe pinnata plant, or one of the most common species of Kalanchoe, have been observed to have distinct morphological and microscopic characteristics. Further, it was discovered that different species of Kalanchoe have anti-inflammatory, antioxidant, antibacterial, and wound healing properties, which enable the plant to be used for dermatological products that are available to the market. With this, it is recommended that further studies be conducted in other understudied species of Kalanchoe regarding their pharmacological properties, as well as the use of other structures of the Kalanchoe plant for treatment of various dermatological conditions.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

The concept of Design Fatigue Factors (DFFs) was introduced for providing desired level of safety in structural fatigue design, often associated with damage calculated from S-N curves. Calculation of fatigue damage from S-N curves can be affected by multiple factors, e.g. types of weld class, corrosion condition, loading conditions, stress concentration on different geometries etc. Each of them can be subject to different level of uncertainties. This study intends to recalibrate the DFFs from a detailed reliability analysis by investigating the probabilistic models derived from the database of S-N curves that has been most frequently used in offshore wind industry. The results of such study indicate that the DFFs can be reduced substantially for the corrosive environmental fatigue models from current standards to the same level of target reliability.

Crohn's disease (CD) is a chronic, relapsing disorder belonging to inflammatory bowel diseases (IBD). It is manifested by relapsing transmural inflammation found in any segment of the gastrointestinal tract. Chronic fatigue is a common and underrecognized symptom of CD, which prevalence is much higher in the population of CD patients as compared to healthy population. It stems from an intricate web of interactions between various risk factors, and its pathophysiology is still not fully understood. Implementation of routine screening and holistic, multidisciplinary approach involving psychological support may be crucial in management of CD patients with chronic fatigue. There is currently no single intervention aimed at decreasing fatigue alone, and its treatment is especially difficult in patients with fatigue persisting despite clinical and endoscopic remission. Extensive research is still needed in order to be able to predict, prevent, identify and ultimately treat fatigue associated with CD. The aim of this review is to summarize the knowledge on the etiology, diagnosis, and treatment of chronic fatigue in CD patients.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.

Technical components should be produced sustainably and are subject to growing demands in terms of durability and reliability. To meet these expectations, the development of thermochemical processes is auspicious. Titanium alloys, which have a comparatively high gas solubility, allow temporary hydrogen (H) loading, often called thermo hydrogen treatment (THT). THT causes lattice deformation and reduces the β transformation temperature. These effects enable an adjustment of the microstructure, which improves the mechanical properties as compared to those produced conventionally. Furthermore, the process is applicable to complex geometries that cannot be surface hardened by mechanical surface treatment techniques. The investigation presented intends to realize a local microstructure gradient in additively via laser-powder bed fusion (L-PBF) manufactured cylindrical Ti–6Al–4V specimens by changing the distribution and morphology of strengthening precipitates as well as the β grain size depending on the distance to the surface, which should improve the material fatigue properties. To evaluate the mechanical properties of such THT-induced microstructure gradients, the resulting change in fatigue life in the LCF and HCF range was determined by stress-controlled cyclic deformation tests. Besides, the resulting microstructure was characterized by means of XRD and TEM. In addition to the additively manufactured and thermo hydrogen treated cylindrical specimens, conventionally produced tube-like specimens were thermo hydrogen treated and examined. For the THT-induced microstructure gradients, numerically simulated H concentration profiles as well as experimentally determined hardness profiles were used for the evaluation of the THT process. The study shows that H-loading at 500°C and H-degassing at 750°C, followed by aging at 550°C, allows the establishment of a microstructure gradient that shows an 8% improvement in fatigue properties compared to a reference condition without THT. The reason for this improvement is an increased volume fraction secondary alpha phase in the near-surface area of the specimens. Moreover, the results show that the process is applicable a tube-like specimen with varying wall thicknesses.

Background: The Balaruc-les-Bains’ thermal mud was found to be colonized predominantly by microorganisms, with cyanobacteria constituting the primary organism in the microbial biofilm observed on the mud surface. The success of cyanobacteria in colonizing this specific ecological niche can be explained in part by their taxa-specific adaptation capacities, and also the diversity of bioactive natural products that they synthesize. This array of components has physiological and ecological properties that may be exploited for various applications.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil &amp; gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

Opuntia ficus-indica (L.) Mill. belongs to the Cactaceae family and the genus Opuntia; it is a succulent plant that adapts to extreme climatic conditions. The aerial part of the plant consists of the cladodes, morphological changes of branches that appear green, are covered with thorns, and are essential to reduce excessive perspiration of water. The composition of cladodes is very varied, and the main constituents are water, fibers, polysaccharides, proteins, fatty acids, vitamins, sterols, minerals, and polyphenols. Polyphenols are responsible for many beneficial activities for human health, such as antioxidant, anti-inflammatory, antitumor, and nutritional properties. The purpose of this manuscript was to compare the properties of cladodes belonging to the same plant but with different stages of maturity. Relative extracts were tested both in vitro and on a cell line and antioxidant and anti-apoptotic properties were found. The antioxidant activity was tested by the ORAC test, the DPPH test, and the measurement of cellular accumulation of ROS. Anti-apoptotic activity was evaluated by the annexin/PI assay and measurement of caspases 9 and 3 expression. The results obtained have shown that the extracts considered possess antioxidant and anti-apoptotic properties. However, the different stages of maturity of cladodes are essential for the performance of both functions. In addition, important variations have been made in the dissolution of extracts that have brought greater safety in their use. In conclusion, this manuscript provides further information on cladodes of Opuntia ficus-indica, which can be used as adjuvants in many human pathologies.

Herbal cosmetics are cosmetics derived from plants. One example is bakuchiol. Bakuchiol is a meroterpene phenol from the seeds of the Psoralea corylifolia plant. Bakuchiol can be derived from Psoralea grandulosa, Pimelea drupaceae, Ulmus davidiana, Otholobium pubescens, and Piper longum. Bakuchiol has antioxidant, anti-inflammatory, and anti-aging activities such as retinol. Bakuchiol will replace retinol with much better safety. Bakuchiol and retinoids share similar cellular pathways, such as the regulation of retinoic acid, the expression of collagen, and extracellular matrix synthesis enzymes. Bakuchiol has many benefits for the skin, so cosmetics and skin therapy can use bakuchiol. This review aims to provide information about the activity of bakuchiol, which has benefits for facial skin, so that this review can be a reference in making cosmetics containing bakuchiol. Bakuchiol has many benefits for skincare such as anti-aging, anti-hyperpigmentation, anti-oxidant, anti-inflammatory, anti-acne, and anti-melanogenesis. Products containing bakuchiol on the market are cleansers, serum, nanoemulsion, and cream.

The influence of the addition of 2.5, 5, 7.5, and 10.0% of dried Enoki and Maitake mushrooms on the content of bioactive compounds and some pro-health properties of pasta was studied. The qualitative and quantitative analysis of phenolic compounds performed using the LC-MS/MS technique indicated the highest amount of phenolic compounds in pasta supplemented with Maitake. However, all pasta enriched with Enoki mushrooms contained statistically significant-ly higher content of α-glucans in comparison to the control. In samples subjected to gastrointes-tinal digestion, the antioxidant, and potential anti-inflammatory activities were significantly higher than ethanolic and PBS extracts of samples. The ethanolic extracts from pasta fortified with dried Enoki and Maitake mushrooms had higher antioxidant activity (in some of the anti-radical and reducing power assays ) as well as a higher ability to inhibit lipoxygenase (E2.5 and E5 samples) compared to the control sample. Also some in vitro digested samples of pasta en-riched with dried Enoki and Maitake mushrooms showed higher chelating power (E10, M7.5 and M10); reducing power (E5, E7.5, and M10) and lipoxygenase inhibition (E7.5, E10 and M10) than the control. In conclusion, Enoki and Maitake mushrooms can be used for fortification of semo-lina pasta, conferring healthier characteristics of the product.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

The effect of low cycle fatigue (LCF) pre-damage on the subsequent very high cycle fatigue (VHCF) behavior is investigated in TC21 titanium alloy. LCF pre-damage is applied under 1.8% strain amplitude up to various fractions of the expected life and subsequent VHCF properties are determined using ultrasonic fatigue tests. Results show that 5% of LCF pre-damage insignificantly affects the VHCF limit due to the absent of pre-crack, but decreases the subsequent fatigue crack initiation life estimated by Pairs’ law. Pre-cracks introduced by 10% and 20% of LCF pre-damage significantly reduce the subsequent VHCF limits. The crack initiation site shifts from subsurface-induced fracture for undamaged and 5% of LCF pre-damage specimens to surface pre-crack for 10% and 20% of LCF pre-damage specimens in very high cycle region. The fracture mechanism analysis indicate that LCF pre-crack will re-start to propagate under subsequently low stress amplitude when stress intensity factor of pre-crack is larger than its threshold. Furthermore, the predicted fatigue limits based on EI Haddad model for the LCF pre-damage specimens well agree with the experimental results.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

The increasing demand by consumers for popular healthy fruits, such as the watermelon (Citrullus lanatus), generate substantial bio-wastes, making it imperative to harness the value of these by-products. Watermelon has low-calorie content and several other nutritional benefits that make it suitable for weight management and heart-healthy diets. Within this article, the nutritional composition and bioactives of watermelon which are strongly linked to the prevention of cardiovascular disorders (CVD), cancer, and age-related conditions, will be thoroughly reviewed. In addition, the therapeutic potential effects of watermelon consumption, such as anti-inflammatory, cardio-protective and anti-cancer properties, are also examined, with emphasis to the importance of incorporating watermelon into regular diets for overall health improvement. Additionally, the study explores various applications of watermelon by-products in functional foods, contributing to meeting recommended daily nutrient allowances, as well as in other functional products like cosmetics, with health promoting properties. In conclusion, this comprehensive review underscores the role of watermelon and its by-products for the development of products that can contribute to the prevention of chronic diseases and promote overall well-being

A twin-screw extruder was used to fabricate poly(butylene succinate) (PBS)/high density polyethylene (HDPE) blends (7:3 weight ratio) and blend-based nanocomposites. Carbon nanotubes (CNTs), graphene nanoplatelets (GNPs) and organoclays (15A and 30B) served as the nanofiller, while maleated HDPE (PEgMA) acted as an efficient compatibilizer for the blend. In the composites, individual nanofillers were mostly localized in HDPE domains, but some fillers were also observed at PBS-HDPE interfaces. The sea-island morphology of compatibilized blend evolved into a pseudo-co-continuous morphology in the composites. Differential scanning calorimetry results confirmed that PEgMA with HDPE evidently accelerated the crystallization of PBS in the blend. The possible nucleation effect of added fillers on PBS crystallization was obscured by the formation of quasi-connected HDPE domains, causing less PBS nucleation sites. The presence of nanofillers improved the thermal stability and burning anti-dripping behavior of the parent blend. The anti-dripping efficiency of added fillers followed the sequence: CNT>15A>30B>GNP. Rigidity of the blend was increased after formation of nanocomposites. In particular, adding GNP resulted in 31% increase in flexural modulus. Development of a pseudo-network structure in the composites was confirmed by measurement of rheological properties. Electrical resistivity of the blend was reduced by more than 6 orders of magnitude at 3 phr CNT loading, demonstrating the achievement of double percolation morphology.

At present, failure definition and damage characteristic curve (DCC) analysis included in the framework to assess bitumen fatigue cracking performance have an inconsistency in ranking bitumen fatigue behaviour. This study utilized two types of self-healing polymers (STP and IPA1w) to modify the neat asphalt (NA), and research four different types of bitumens: NA, STP-modified bitumen, IPA1w-modified bitumen, and styrene-butadiene-styrene modified bitumen (SBSB), to evaluate the above-mentioned framework. All bitumens were subjected to short-term and long-term aging and tested utilizing the Linear amplitude sweep (LAS) test and simplified viscoelastic-continuum-damage (S-VECD) model. The results showed that the SBSB exhibited the highest numbers of loading cycles (in long-term aging analysis) to reach failure points at 25°C, 28°C, and 31°C which were 2290, 2340, and 2510, respectively. However, this bitumen failed to exhibit the best performance in terms of DCC assessment under the same conditions, confirming the above-mentioned inconsistency. Besides, the current failure criterion could not accurately predict bitumen fatigue behaviour under certain test conditions because two R2 values were below 0.1. As a result, this study proposed a new failure definition and failure criterion to overcome these issues. The proposed failure definition agreed with the DCC analysis to rank bitumen fatigue performance, and the proposed failure criterion showed R2 values higher than 0.9. The new framework presented the modified bitumen containing 0.5% of STP as the asphalt binder with the best fatigue cracking performance, according to the selected test conditions.

The fatigue life of concrete is affected by many interwoven factors whose effect is nonlinear. Be-cause of its unique self-learning ability and strong generalization capability, the Bayesian regu-larized backpropagation neural network (BR-BPNN) is proposed to predict concrete behavior in tensile fatigue. The optimal model was determined through various combinations of network parameters. The average relative impact value (ARIV) was constructed to evaluate the correla-tion between fatigue life and its influencing parameters (maximum stress level Smax, stress ratio R, static strength f, failure probability P). ARIV results were also compared with other factor as-sessment methods (weight equation and multiple linear regression analyses). Using BR-BPNN, S-N curves were then obtained for the combinations of R=0.1, 0.2, 0.5; f=5, 6, 7MPa; P=5%, 50%, 95%. The tensile fatigue results under different testing conditions were finally compared for compatibility. It was concluded that Smax has the most significant negative effect on fatigue life; the degree of influence of R, P, and f, which positively correlate with fatigue life, decreases suc-cessively. ARIV is confirmed as a feasible way to analyze the importance of parameters and could be recommended for future applications. The tensile fatigue performance of plain concrete under different stress states (flexural tension, axial tension, splitting tension) does not differ sig-nificantly. Besides utilizing the valuable fatigue test data scattered in the literature, insights gained from this work could provide a reference for subsequent fatigue test program design and fatigue evaluation.

Fatigue loading is critical to fibre reinforced polymer composites due to their anisotropic and heterogenous nature. This study investigated the tensile fatigue behaviour of polyester and vinyl ester based GFRP laminates to understand the critical aspects of failure mode and fatigue life under cyclic loading. GFRP laminates with two different resin systems (polyester and vinyl ester), two different stress ratios (0.1 and 0.5) and two different environmental conditions (air and water) were investigated at an applied stress of 80%, 60% and 40% of the ultimate capacity. Based on the investigated parameters (i.e., resin types, stress ratio, environmental conditioning and maximum applied stress), a fatigue model was proposed. Results show that the resin system plays a great role in fatigue failure mode while the stress ratio and environmental condition significantly affect the tensile fatigue life of GFRP laminates. The types of resin used in GFRP laminates and environmental conditions as input parameter in the proposed fatigue model is a unique contribution.

The growing worldwide cancer incidence, coupled to the increasing occurrence of multidrug cancer resistance, requires a continuous effort towards the identification of new leads for cancer management. In this work, two C-scorpionate complexes, [FeCl2(κ3-Tpm)] (1) and [Co(κ3-TpmOH)2] (2), (Tpm = hydrotris(pyrazol-1-yl)methane and TpmOH = 2,2,2-tris(pyrazol-1-yl)ethanol), are studied as potential scaffolds for future anti-cancer drug development. Their cytotoxicity and cell migration inhibitory activity are analyzed, and an untargeted metabolomics approach is em-ployed to elucidate the biological processes significantly affected by these two complexes, using two tumoral cell lines (B16 and HCT116) and a non-tumoral cell line (HaCaT). While [FeCl2(κ3-Tpm)] did not display a significant cytotoxicity, [Co(κ3-TpmOH)2] was particularly cy-totoxic against the B16 cell line. While [Co(κ3-TpmOH)2] significantly inhibited cell migration in all tested cell lines, [FeCl2(κ3-Tpm)] displayed a mixed activity. From a metabolomics perspective, exposure to [FeCl2(κ3-Tpm)] is associated with changes in various metabolic pathways involving tyrosine, where iron-dependent enzymes are particularly relevant. On the other hand, [Co(κ3-TpmOH)2] is associated with dysregulation of cell adhesion and membrane structural pathways, suggesting its antiproliferative and anti-migration properties can be due to changes in the overall cellular adhesion mechanisms.

Encephalitis is a condition with a variety of etiologies, clinical presentations and degrees of severity. The causes of these disorders include both neuroinfections and autoimmune diseases in which host antibodies are pathologically directed against self antigens. In autoimmune encephalitis, autoantibodies are expressed in the central nervous system. The incidence of this disease is approximately 4% of all reported cases of encephalitis. Autoimmune encephalitis can be induced by antibodies against neuronal surface antigens such as N-methyl-D-aspartate-activated glutamate receptors (NMDAR), ⍺-amino-3-hydroxy-5-methyl-4-isoxazole propionate receptors (AMPAR) or gangliosides GQ1b, DPPX, CASPR2, LGI1, as well as by antibodies against neuronal intracellular antigens. The paper presents a number of both mental and neurological symptoms of autoimmune encephalitis. Moreover, the coexistence of psychoses, neoplastic diseases and the methods of diagnosing autoimmune encephalitis are discussed. Attention was also drawn to the fact that early diagnosis, as well as early initiation of targeted treatment, increases the chance of a successful course of the therapeutic process.

High-performance properties of interpenetration polymer network (IPN) hydrogels, based on physically crosslinked chitosan (CS) and chemically crosslinked poly(N-isopropylacrylamide) (PNiPAM), have been successfully developed. The IPN of CS/PNiPAM is proposed to overcome the limited mechanical properties of the single CS network. In this study, the viscoelastic behaviors of prepared materials in both solution and gel states have been extensively examined, considering the UV exposure time and crosslinker concentration as key factors. The effect of these factors on gel formation, hydrogel structures, thermal stabilities of networks, and HeLa cell adhesion were studied sequentially. The sol-gel transition was effectively demonstrated through the scaling law, which agrees well with Winter and Chambon's theory. By subjecting the CS hydrogel to the process operation in an ethanol solution, its properties can be significantly enhanced with increased crosslinker concentration, including the shear modulus, crosslinking degree, gel strength, and thermal stability in its swollen state. The IPN samples exhibit a smooth and dense surface with irregular pores, allowing for much water absorption. The HeLa cells were adhered to and killed using the CS surface cationic derivative, then released through hydrolysis by utilizing the hydrophilic/hydrophobic switchable property or thermo-reversible gelation of the PNiPAM network. The results demonstrated that IPN is a highly attractive candidate for anti-fouling materials.

Work reviews the new isolated isolated cembranoid diterpene derivatives from species belonging to the family Alcyoniidae, which comprises the genera Sarcophyton, Sinularia, and Lobophytum as well as their biological properties, during 2016–2017. The compilation permitted to conclude that much more new cembranoid diterpenes were found in the soft corals of the genus Sarcophyton sp. (33 new compounds) than in those belonging to the genera Lobophytum (17) or Sinularia (8). Several methods have been used for identifying these new compounds, after extraction with organic solvents and fractionation. The fractions obtained, in some cases, were followed by TLC, and again subjected to chromatographic procedures, including semi-preparative HPLC. Beyond the chemical composition, the biological properties were also evaluated, namely anti-microbial against several Gram-positive and Gram-negative bacteria and fungi, anti-inflammatory and anti-tumoral against several types of cancer cells. Although the biological activities detected in almost all samples, they were not outstanding ones.

Fastener holes are among the most common natural stress concentrators in metal structures. The life cycles of various structural elements, such as those in aircraft structures, automobiles, and rail-end bolt joints are limited by fatigue damage around the holes. An effective approach to delay the formation and growth of fatigue macrocracks is to introduce residual hoop compressive stresses around the holes. Two methods have become established in the prestressing of fastener holes in aircraft components: split sleeve and split mandrel, which implement one-sided processes. The common disadvantage of both methods is the complex procedure due to the need for high accuracy of the initial holes. This article presents a new modified split mandrel method providing the same tightness (interference fit) with a wide tolerance of the pre-drilled hole diameters reducing the number of technological cycle steps and production costs. То implement the new method, a functionally connected tool and a device with a hydraulic drive were developed. An extensive experimental study of 2024-T3 AA specimens was carried out to evaluate the effectiveness of the method under a high scattering of the pre-drilled holes. The new method provided a deep zone of residual hoop compressive stresses on both faces of the specimens after cold working and after hole final reaming. The removal of a plastically deformed layer around the hole of suitable thickness during the final reaming decreased the axial gradient of residual hoop stress distribution. Fatigue tests on a tensile pulsating cycle verified the effectiveness of the modified split mandrel method to significantly increase the fatigue life by 6.6 times based on cycle fatigue strength compared to the conventional case of machining the holes. The obtained S-N curves for three groups of samples with initial hole diameters of 8.0, 8.1, and 8.2 mm which were cold worked with the same tightness of 0.32 mm and final reamed, aligned well indicating that the new method can provide constant fatigue strength for a given stress amplitude.

TThe aim of the work is to present a newly developed stand and methodology of accelerated tests of fatigue strength of flexible propellers and fins. The paper presents the design and concepts of the measuring elements used in the research. Test methodology and water stressing were devel-oped. The mechanical properties of the following materials were presented: Arnitel EL-550 and QUEO 8230 with the addition of PP / EVA 50/50 (polypropylene / ethylene-vinyl acetate) - in the proportion of 70/30 (QUEO 8230 / additive). The constructed test stand and a new method of fa-tigue testing of biomimetic fins made it possible to determine the number of fin movement cy-cles under a given load, which may facilitate the determination of a warranty for a newly intro-duced product. The current consumption by the fin drive and video monitoring allowed for the selection of the range of the number of movement cycles and the determination of the moment of fatigue cracks until the fin structure loses its capacity. During the analysis, the test results showed that the fins made of Arnitel EL-550 did not show changes in the measured values of the current and the force generated by the fin. For a fin made of QUEO 8230, at 35,000 cycles, there is a decrease in the current and force consumed, which indicates the initiation of fatigue damage to the fin. The performed tests can be the basis for the development of standards for the fatigue strength of flexible propellers.

Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a complex, multisystem, and profoundly debilitating condition, probably of multifactorial etiology. No effective approved drugs are currently available for its treatment. Several studies have proposed symptomatic treatment with melatonin and zinc supplementation in chronic illnesses; however, little is known about the synergistic effect of this treatment on fatigue-related symptoms in ME/CFS. The primary endpoint of the study was to assess the effect of oral melatonin plus zinc supplementation on fatigue in ME/CFS. Secondary measures included participants’ sleep disturbances, anxiety/depression, and health-related quality of life. A proof-of-concept, 16-week, randomized, placebo-controlled, double-blind trial was conducted in 50 ME/CFS patients assigned to receive either oral melatonin (1 mg) plus zinc (10 mg) supplementation (n = 24) or matching placebo (n = 26) once daily. Endpoint outcomes were evaluated at baseline and then reassessed at 8 and 16 weeks of treatment and 4 weeks after treatment cessation, using self-reported outcome measures. Treatment was safe and well-tolerated. The most relevant results were the significant reduction in the perception of physical fatigue in the active group at the final follow-up versus placebo (p < 0.05), and the significant improvement in the physical component summary at all follow-up visits in the experimental group. Our findings suggest that oral melatonin plus zinc supplementation for 16 weeks is safe and potentially effective in reducing fatigue and improving the quality of life in ME/CFS. This clinical study was registered on ClinicalTrials.gov (NCT03000777).

This paper aims to provide an overall review of degradation, damage evolution and fatigue models in the literature of various engineering materials, mostly metals, and composites.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

Understanding the complex relationship between sleep and memory is a major challenge in neuroscience. Many studies on memory consolidation in humans suggest that sleep triggers offline memory processes, resulting in less forgetting of declarative memory and performance stabilization in non-declarative memory. However, issues related to non-optimal experimental designs, task characteristics and measurements, and inappropriate data analysis practices can significantly affect the interpretation of the effect of sleep on memory. In this article, we discuss these issues and suggest constructive solutions to address them. We believe that implementing these solutions in future sleep and memory research will significantly advance this field by improving the understanding of the specific role of sleep in memory consolidation.

Recent works in mechanical fatigue consider that a threshold of entropy exists, the fracture fatigue entropy. The determination of this quantity is usually done considering empirical models for the mechanical power estimation. In this paper, we experimentally observe the existence of a threshold of entropy and exergy in low cycle fatigue for a flat Al-2024 specimen avoiding the use of a model, solely measuring the heat generated during a fatigue test. Results are then compared considering various hypotheses (1D heat dissipation with convection and radiation considered as heat sources, and, heat transfer from a fin with convection and radiation as boundary conditions) to an empirical mechanical model known in the literature and deviations between them are discussed.

Interior permanent magnet motors (IPMSMs) are extensively used as traction motors today because of their exceptional torque and power density, and wide constant power operating range. Under real-world usage, an IPMSM rotor undergoes varying electromagnetic, thermal, and mechanical loads. Under such conditions, fatigue life-based design criteria should be utilized over stress-based design criteria to ensure the structural integrity of the rotor. Moreover, the driving dynamics can change the rotor temperature continuously, which affects the electromagnetic, mechanical, and fatigue properties of rotor material. This paper proposes a robust thermo-mechanical rotor fatigue simulation workflow considering the significant loads acting on an IPMSM rotor and the temperature variation throughout a drive cycle. It discusses an accelerated fatigue life estimation approach based on peak valley extraction to reduce the simulation time significantly for stress and fatigue analysis. Then, it presents a method for stress-life curve generation for a variable loading. It also presents a sensitivity study with a median S-N curve, and a 90%-reliability 95%-confidence (R90C95) S-N curve.

Background: Permanent Daylight Savings Time (DST) may improve road safety by providing more daylight in the evening but could merely shift risk to morning commutes or increase risk due to fatigue and circadian misalignment. Methods: To identify how potential daylight exposure and fatigue risk could differ between permanent DST versus permanent Standard Time (ST) or current time arrangements (CTA), generic work and school schedules in five United States cities were modeled in SAFTE-FAST biomathematical modeling software. Commute data were categorized by morning (0700-0900) and evening (1600-1800) rush hours. Results: Percent darkness was greater under DST compared to ST for the total waking day (t=2.59, p=0.03) and sleep periods (t=2.46, p=0.045). Waketimes occurred before sunrise 63%±41% percent of the time under DST compared to CTA (42%±37%) or ST (33%±38%; F(2, 74)=76.37; p<0.001). Percent darkness was greater during morning (16%±31%) and lower during evening rush hour (0%±0%) in DST compare to either CTA (morning:7%±23%; evening:7%±14%) or ST (morning:7%±23%; evening:7%±15%). Discussion: Morning rush hour overlapped with students’ commutes and shift worker reverse commutes, which may increase traffic congestion and risk compared to evening rush hour. Switching to permanent DST may be more disruptive than either switching to ST or keeping CTA without noticeable benefit to fatigue or potential daylight exposure.

Most of the research of mental fatigue evaluation mainly concentrated on some indexes that require sophisticate and large instruments which make the detection of mental fatigue cumbersome, time-consuming, and difficult to apply on a large scale. A quick and sensitive mental fatigue detection index is necessary so that mental workers can be alerted in time and take corresponding countermeasures. But to date, no studies have compared the sensitivity of common objective evaluation indexes. To solve these problems this study recruited 56 human subjects. These subjects were evaluated using six fatigue indexes: the Stanford sleepiness scale, digital span, digital decoding, short-term memory, critical flicker fusion frequency (CFF), and speed perception deviation. The results of fatigue tests before and after mental fatigue were compared, and a one-way analysis of variance (ANOVA) was performed on the speed perception deviation. The result indicated the significance of this index. Considering individual differences, the relative fatigue index (RFI) was proposed to compare the sensitivity of the indexes. The results showed that when the self-rated fatigue grade changed from non-fatigue to mild fatigue, the ranges of RFI values for digital span, digital decoding, short-term memory and CFF were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. Correspondingly, when the self-rated fatigue grade changed from non-fatigue to severe fatigue, the ranges of RFI values for the above indexes were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. These results suggest that the sensitivity of the digital decoding, digital span, short-term memory, and CFF decreased sequentially when the self-evaluated fatigue grade changed from no fatigue to mild or severe fatigue. The RFI individuality of the speed perception deviation is highly variable and is not suitable as an evaluation index. In mental fatigue testing, digital decoding testing can provide faster, more convenient, and more accurate results.

Curcumin is the main secondary metabolites of Curcuma longa and other Curcuma spp, and has been reported to have some potential in preventing and treating some physiological disorders. This study investigated the effect curcumin in inhibiting high-fat diet and streptozotocin (STZ)-induced hyperglycemia and hyperlipidemia in rats. Twenty-six male Sprague-Dawley (SD) rats (170-190 g) were randomly divided into a standard food pellet diet group (Control group), a high-fat diet and streptozotocin group (HF+STZ group), and a high-fat diet combined with curcumin and STZ group (HF+ Cur +STZ group). Compared with the HF+STZ group, the HF+Cur+STZ group exhibited significantly reduced fasting blood glucose (FBG), total cholesterol (TC), triglyceride (TG), low-density lipoprotein cholesterol (LDL-C), high-density lipoprotein cholesterol (HDL-C), alanine aminotransferase (AST) and aspartate transaminase (ALT) levels, and liver coefficients; in the livers of these rats, the expression of malondialdehyde (MDA) and Bax was downregulated, whereas that of superoxide dismutase (SOD) and Bcl-2 was upregulated. Moreover, the liver histology of these rats was improved and resembled that of the control rats. These results suggest that curcumin prevents high-fat diet and STZ-induced hyperglycemia and hyperlipidemia, mainly via anti-oxidant and anti-apoptotic mechanisms in the liver.

The formation and propagation of cracks occurs through irreversible dislocation movements at notches, material defects and grain boundaries. Since this process is partly thermally controlled, the resistance to dislocation movements at low temperatures increases. This slows both fatigue initiation and fatigue crack propagation. From recent experimental data, it can be seen that fatigue crack growth is accelerated below the fatigue transition temperature (FTT) that correlates with the ductile-brittle transition temperature (DBTT) found by well-known fracture mechanics tests, i.e., Charpy impact, fracture toughness, and CTOD. Hence, this study investigates the relation between FTT and DBTT in S500 high-strength steel base material and welded joints at low temperatures using fatigue crack growth, fracture toughness tests as well as scanning electron microscopy. From the tests, an almost constant decrease in fatigue crack propagation rate is determined with decreasing test temperature even below the DBTT.

Fatigue failure remains a critical concern in structural engineering and material science, prompting extensive research to understand and predict the behaviour of materials under cyclic loading conditions. The present study aims to investigate the fatigue life of carbon steel specimens containing opposite semicircular edge notches through a comprehensive experimental and numerical analysis. In this study, stress concentration factors (SCF, K_t) of rectangular plate with opposite semicircular notches are considered under uniform tensile stress to analyse the notch deformation because of stretching of plate. Furthermore, the research focuses on quantifying stress concentration factors (SCFs) for these notches based on S-N curves of carbon steel. The study employs a combination of experimental and numerical techniques to understand the influence of these notches on the fatigue performance of carbon steel structures. A plate with opposite semicircular edge single notches under the axial load creates stress concentration near the notch and it is much larger than the average stress on the plate. Both analytical and finite element methods are used to calculate the maximum stress around the notch. SOLIDWORKS Premium Student Edition 2023 has been employed for modelling and SOLIDWORKS Simulation Premium Student Edition 2023 has been used for stress analysis and fatigue notch factor of rectangular plate of size 31 mm x 25.4 mm x 6.35 mm. The uniform tensile load with a magnitude of 20195 N is applied on one sides of rectangular plate normal to the sides of notches with ratio h/r = 1, for the semicircular notch. The result obtained on both analytical and finite element methods are compared and the percentage of error has been evaluated. Subsequently, these specimens undergo fatigue testing under varying loading conditions to capture their fatigue behaviour. The acquired fatigue data is then plotted against stress amplitude to construct S-N curves, forming the foundation for assessing the fatigue life of the notched specimens. To complement the experimental findings and to gain a deeper understanding of the stress concentration phenomenon, numerical simulations are conducted using advanced finite element analysis (FEA) techniques. The finite element models are carefully calibrated against the experimental results to ensure their accuracy and reliability. The FEA simulations enable the determination of stress concentration factors at critical locations within the notched specimens, further validating the experimental observations. The investigation reveals crucial insights into the effect of opposite semicircular edge notches on the fatigue life of carbon steel structures. The obtained S-N curves allow engineers and designers to predict the fatigue life of components with similar notches, aiding in the development of reliable and durable structures in practical applications. Moreover, the stress concentration factors determined from the numerical simulations provide valuable data to assess the potential failure modes and to optimise designs, effectively mitigating fatigue-related failures. The combination of experimental and numerical approaches ensures a comprehensive and rigorous analysis of the fatigue behaviour in notched specimens, offering a reliable basis for making informed engineering decisions. The comparison between the analytical method and the Finite Element Method (FEM) demonstrated good agreement, with an error percentage of 4.272%. The analysis revealed that the specimen would experience failure after approximately 2882 cycles, with a maximum stress of 395.914 MPa. This research study enhances the understanding of fatigue life in carbon steel structures containing opposite semicircular edge notches and contributes valuable data to the field of fatigue mechanics. The outcomes serve as a valuable resource for professionals engaged in structural engineering, material science, and design optimisation, ultimately leading to safer and more durable industrial components in critical applications. The findings of this research contribute to the understanding of fatigue behaviour in carbon steel components with stress concentration effects caused by semicircular notches. Moreover, the validated numerical simulations and data curves facilitate the prediction of fatigue life and aid in determining the critical conditions leading to fatigue failure. In conclusion, this research highlights the significance of combining experimental testing with numerical simulations to comprehensively analyse the fatigue life of carbon steel specimens with opposite semicircular edge notches. The obtained stress concentration factors provide crucial information for structural integrity assessment and offer potential for further optimising design criteria to mitigate fatigue-related failures. The findings of this study could play a vital role in enhancing the reliability and safety of carbon steel structures subjected to cyclic loading conditions. The comprehensive experimental and numerical analyses establish a foundation for future studies exploring other materials and geometries with notches, fostering advancements in fatigue life prediction and structural integrity assessment.

Inotodiol, a lanostane-type triterpenoid, and many phytochemicals from Chaga mushroom have been investigated for various allergic diseases. However, antiaging and anti-inflammatory activities of inotodiol under different types of oxidative stress and impact of inotodiol on collagen and hyaluronan synthesis are not sufficiently studied. Lanostane triterpenoids-rich concentrate, which contained 10% inotodiol as major (the inotodiol concentrate), was prepared from Chaga and compared with pure inotodiol in terms of anti-inflammatory activities on a human keratinocyte cell line, HaCaT cells, under various stimulation such as stimulation with ultraviolet (UV) B or tumor necrosis factor (TNF)-α. In stimulation with TNF-α, interleukin (IL)-1β, IL-6, and IL-8 genes were significantly repressed by 0.44~4.0 μg/mL of pure inotodiol. UVB irradiation induced overexpressions of pro-inflammatory cytokines, but those genes were significantly suppressed by pure inotodiol or inotodiol concentrate. Moreover, pure inotodiol/inotodiol concentrate could also modulate synthesis of collagen and hyaluronic acid by controlling COL1A2 and HAS2/3 expression, which implies a crucial role of pure inotodiol/inotodiol concentrate in prevention of skin aging. These results enlighten anti-inflammatory and anti-aging effect of pure inotodiol/inotodiol concentrate, and it is highly conceivable that pure inotodiol and inotodiol concentrate could be promising natural bioactive substances to be incorporated in therapeutic and beautifying applications.

Antibiotic failure is one of the most worrying health problems worldwide. Nowadays we are facing an international crisis where several issues are involved: new antibiotics are not being discovered any longer, resistance mechanisms become spread in nearly every clinical isolate of bacteria and the appearance of recurrent infections caused by persistent bacteria complicates the overcoming of infections. In this context, it has been explored new anti-infectious strategies against MDR and persistent bacteria as well as the rescue of FDA-approved compounds (drug repurposing). Among the highlighted new anti-infectious strategies we find anti-microbial peptides, anti-virulence compounds, phage therapy and new molecules. On the other hand, as drugs of repurposing that have been described, we have anti-inflammatory compounds, anti-psychotics, anti-helmintic drugs, anti-cancerous and statins.

Counterfeiting and theft have always been problems that incur high costs and results in considerable losses for the international markets. In this research paper, we will address the issue of counterfeiting while using RFID technology in retailer systems or other industries by presenting a new anti-counterfeiting and anti-theft system for the retailer market. This system will address the two above mentioned issues and provide a solution that can save the retailer systems millions of dollars yearly. This proposed system will achieve the objective of preventing or minimising the counterfeiting and theft of tagged products. At the same time, it will provide a strong indication for suspiciously sold or obtained items. Furthermore, we conducted a security analysis to prove the correctness of our protocol on the basis of the strand spaces.

Most of the damage to Vleg cars was caused by material fatigue. The objectives of the fatigue analysis on Xenia 2011 car wheels with the Finite Element Method using Solidworks are: 1) Knowing the fatigue analysis process on car wheels, 2) Knowing the results of the fatigue analysis on car wheels. The research method used is the Finite Element Method (FEM) method; the re-search steps include model data retrieval from the Wheel code, 3D model creation process, static simulation process according to SAE J 328 standard, mesh variations, fatigue simulation, and finally, standardization of results fatigue simulation regarding the SAE J 328 standard. The re-sults of the fatigue analysis on the Xenia 2011 car wheels obtained an age of 1000,000 cycles when compared with the minimum average of SAE J 328 of 600,000 cycles, this product design is clas-sified as a high cycle, which means it will experience a prolonged failure, and this design has a maximum alternating stress value of 627.4702 MPa, a strain of 0.007105, a displacement of 7.148 mm and a SOF of 0.087890 with a load factor used of 2.5, so overall this Xenia car can be loaded with a load of 1775 kg, if it is more than that, then Wheels will experience cracking.

The aim of this study was to compare the screw removal torque of mini conical prosthetic components and straight trunnion of indexed morse taper implants, after mechanical cycling. The sample consisted of 40 implants and 20 mini-conical prosthetic components (MC group) and 20 straight trunnion components (ST group). Each group consisted of 10 specimens, with 2 implants in each, and cobalt-chromium metallic crowns were screwed into each sample. The components of the MC group received a torque of 20 N.cm with a digital torque wrench and after 10 minutes were retightened with the same value as the initial torque. The components of the ST group received a torque of 30 N.cm, with a digital torque wrench and after 10 minutes, they were retightened with the same value. The screws of the respective crowns of the two groups received a torque of 10 N.cm and after 10 minutes were retightened with the same value. Each group was subjected to the fatigue test in a mechanical cycler at 2.000.000 cycles, with a load of 250 N and frequency of 4 Hz. At the end of the fatigue test, the loosening torque of each screw of the specimens was measured through a digital torque wrench. The data were analyzed by two-way ANOVA and Tukey test. In both groups, there were loss of torque. The results showed no statistic difference between MC and ST groups.

Nonlinear ultrasonic testing has been accepted as a promising manner for evaluating material integrity in an early stage. Stress fatigue is the main threats to train safety, railways examinations for stress fatigue are more significant and necessary. A series of ultrasonic nonlinear wave experiments are conducted for rail specimens extracted from railhead with different degree of fatigue produced by three-point bent loading condition. The nonlinear parameter is the indicator of nonlinear waves for expressing the degree the fatigue. The experimental results show that the sensitivity of a third harmonic longitudinal wave is higher than second harmonic longitudinal wave testing. As the same time, collinear wave mixing shows strong relative with fatigue damages than a second longitudinal wave NDT method and provides more reliable results than third harmonic longitudinal waves nonlinear testing method.

Background: Knee joint is a common site for injury among younger people, the purpose of this study is to measure the skeletal muscle endurance and strength on people with prior knee reconstruction surgery. Methods: Young healthy female subjects were tested who reported having knee reconstruction surgery of over one year prior to testing. The skeletal muscle endurance index of the hamstring and quadriceps muscles was determined as the decline in the specific muscle acceleration in response to 2, 4, and 6 Hz electrical stimulation. Maximal isometric muscle strength (MVC) was measured in the hamstring and quadriceps muscles. Results: The hamstring muscles in the affected leg had less endurance than the non-affected leg at 6 Hz stimulation (55.5 ± 13.2% versus 78.0 ± 13.3%, P = 0.01). Muscle endurance was not reduced in the quadriceps muscles in the affected leg compared to the non-affected leg at 6 Hz stimulation (78.0 ± 13.3% versus 80.3 ± 10.0%, P = 0.69). There were no differences in MVC between the affected and non-affected legs for either the hamstring (P= 0.20) or quadriceps muscles (p = 0.67). Conclusions: Muscle endurance is reduced in the hamstring muscles at least one-year post injury, while hamstring strength is not. Reduced hamstring muscle endurance could be a result of a lack of focus on muscle endurance during rehabilitation after injury and may contribute to re-injury in the particular muscle even in people who have recovered muscle strength.

Post-viral fatigue syndrome (PVFS) encompasses a wide range of complex neuroimmune disorders of unknown cause characterized by disabling post-exertional fatigue, myalgia and joint pain, cognitive impairments, unrefreshing sleep, autonomic dysfunction, and neuropsychiatric symptoms. It includes myalgic encephalomyelitis, also known as chronic fatigue syndrome (ME/CFS), fibromyalgia (FM), and more recently post-COVID-19 condition (Long COVID). To date, there are no definitive clinical case criteria and no FDA-approved pharmacological therapies for PVFS. Given the current lack of effective treatments, there is a need to develop novel therapeutic strategies for these disorders. Mitochondria, the cellular organelles responsible for tissue energy production, have recently garnered attention in research into PVFS due to their crucial role in cellular bioenergetic metabolism in these conditions. Accumulating literature has identified a link between mitochondrial dysfunction and low-grade systemic inflammation in ME/CFS, FM, and Long COVID. To address this issue, this article aimed to critically review the evidence relating to mitochondrial dysfunction in the pathogenesis of these disorders; in particular, to evaluate the effectiveness of coenzyme Q10 supplementation on chronic fatigue and pain symptoms as a novel therapeutic strategy for the treatment of PVFS.

We asked whether the level of peripheral fatigue would differ when three consecutive exercise trials were completed to task failure, and whether there would be delayed recovery in maximal voluntary contraction (MVC) force, neuromuscular activation and peripheral fatigue following task failure. Ten trained sport students performed three consecutive knee extension isometric trials (T1, T2, T3) to task failure without breaks between trials. T1 and T2 consisted of repeated 5-s contractions followed by 5-s rest. In T1, contractions were performed at a target force at 60% pre-exercise MVC. In T2, all contractions were MVCs, and task failure occurred at 50% MVC. T3 was a sustained MVC performed until force fell below 15% MVC. Evoked force responses to supramaximal electrical femoral nerve stimulation were recorded to assess peripheral fatigue. Electromyography signals were normalized to M-wave amplitude to assess neuromuscular activation. Lower levels of evoked peak forces were observed at T3 compared to T2 and T1. Within 5 s of task failure in T3, MVC force and neuromuscular activation recovered substantially without any recovery in evoked peak force. Neuromuscular activation 5-10 s after T3 was unchanged from pre-exercise values, but evoked peak forces were substantially reduced. These results challenge the existence of a critical peripheral fatigue threshold that reduces neuromuscular activation. Since neuromuscular activation changed independently of any change in evoked peak force, immediate recovery in force production after exercise is due to increased central recruitment and not to peripheral mechanisms.

Vaginal ecosystem is a unique environment where, in physiological conditions, lactobacilli dominate. However, also pathogenic microbial species, responsible of vaginitis and vaginosis, can harbor vaginal microbiota. To extend the data published by De Seta and Larsen in Pathogens (2021), here we analyzed both the anti-Candida and anti-inflammatory properties of the vaginal gel formulation, Respecta® Balance Gel (RBG), commercialized as an adjuvant to treat vaginitis and vaginosis. We evaluated its activity by an in vitro model where a monolayer of A-431 vaginal epithelial cells was infected by Candida albicans in the presence of RBG or the placebo formulation (pRBG). Specifically, we tested the RBG capacity to counteract C. albicans virulence factors as well as their anti-inflammatory properties. Our results show that, unlike the placebo, RBG reduces ,reduces, C. albicans adhesion, its capacity to form hyphae and C. albicans-induced vaginal cell damage. Interestingly, both RBG and pRBG reduce LPS-induced IL-8 secretion (being RBG the most effective) demonstrating that also the placebo retains anti-inflammatory properties. By our experimental approach we highlight the possible role of farnesol on such effects, but we would like to point out that lactic acid, polydextrose and glycogen too must be relevant in the actual application. Taken together, our results show that RBG impairs C. albicans virulence and is able to reduce the inflammation in the vaginal environment, ultimately allowing the establishment of a balanced vaginal ecosystem.

Maslinic acid (MA) is a natural triterpene from Olea europaea whose pharmacological functions have been showed. The objective of this study was to examine MA effect on cell viability (by MTT assay), reactive oxygen species (ROS levels, by flow cytometry) and key anti-oxidant enzyme activities (by spectrophotometry) in murine skin melanoma (B16F10) cells compared to healthy cells (A10). MA induced cytotoxic effects in cancer cells (IC50 42 µM) whereas no effect was found in A10 cells treated with MA (up to 210 µM). In order to produce a stress situation in cells, 0.15 mM of H2O2 were added. Under stressful conditions, MA protected both cell lines against oxidative damage, decreasing intracellular ROS, being higher in B16F10 than in A10 cells. The treatment with H2O2 and without MA produced different responses in anti-oxidant enzymes activities depending on cell line. In A10 cells, all enzymes were up-regulated, but in B16F10 cells only superoxide dismutase, glutathione S-transferase and glutathione peroxidase increased their activities. MA restored the enzyme activities to similar levels than control group in both cell lines, highlighting that in A10 cells the highest MA doses induced values lower than control. Overall, these findings demonstrate the great anti-oxidant capacity of MA.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

Immune-mediated necrotizing myopathy (IMNM) is a rare and severe disease that corresponds to a specific entity of idiopathic inflammatory myopathy. Patients with IMNM suffer from proximal muscle weakness, and present high levels of creatine kinase and necrotic myofibers. Anti-Signal Recognition Particle (SRP) and anti-3-hydroxy-3-methylglutaryl-coenzyme A reductase autoantibodies (HMGCR) have recently been identified in two thirds of patients with IMNM and are used as a hallmark of the disease. In this review, we provide a detailed description of these antibodies and the tests used to detect them in the serum of patients. Based on in vitro studies and mouse models of IMNM, we will discuss the role of autoantibodies in the pathogenesis of the disease. Finally, in the light of the latest knowledge, we will conclude with a review of recent therapeutic approaches.

Three new polyketides (penidihydrocitrinins A–C, 1–3) and 14 known compounds (4–17) were isolated from the deep-sea-derived Penicillium citrinum W17. Their structures were elucidated by comprehensive analyses of 1D and 2D NMR, HRESIMS, and ECD calculations. Compounds 1–17 were evaluated for their anti-inflammatory and anti-osteoporotic bioactivities. All isolates exhibited significant inhibitory effects on microglial activation in LPS-stimulated BV-2 cells in a dose-response manner. Notably, compound 14 displayed the strongest effect with the IC50 value of 4.7 µM. Moreover, compounds 6, 7, and 8 not only suppressed osteoclastogenesis, but also promoted osteoblast mineralization.

Green products have excellent potential for discovering and producing new medicinal products. In recent years, there is a growing interest towards the green synthesis of metal nanoparticles, particularly from plants sources. This eco-friendly approach was used in the recent research to biosynthesize zinc oxide nanoparticles (ZnO NPs) from Cissus antractica plant. The present study aims to examine the cell cytotoxicity, cell death, and pathways of apoptosis in lung cancer cells (A549) and inflammation properties treated with biosynthesized ZnO NPs. Additionally, synthe-sized ZnO nanoparticles were characterized using UV–vis spectroscopy, X-ray diffraction (XRD), Transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FT-IR), and Energy-dispersive X-ray spectroscopy (EDS). The XRD and TEM analyses exhibited 31 nm as the size of synthesized nanoparticles, the pure crystal form of ZnO NPs, and the shape of the NPs as nearly spherical and hexagonal quartzite. The MTT assay used for cytotoxicity evaluation de-picted the significant toxic effect of CA-ZnONPs against the A549 lung cancer cells at concentra-tions up to 20 µg/mL than non-cancerous cells. Furthermore, we observed an elevated ROS level in cancer cells. These NPs also demonstrated dose-dependent ability to suppress colony for-mation and cell migration, which increases their potential as a lung cancer treatment. Further-more, The NPs formulation's ability to induce apoptosis in cancer cells was further supported by Hoechst and propidium iodide dye. Further, CA ZnO NPs increased the gene expression of BAX, Cyto-c, Caspase 3 and 9, but decreased the expression of Bcl-2, indicating that the nanoformulation triggered mitochondrial-mediated apoptosis. Besides, this study showed that NPs suppressed in-flammatory responses by subsequently decreasing reactive oxygen species (ROS) generation, downregulating the expression of the pro-inflammatory cytokines TNF-α, iNOS, COX-2, IL-6, IL-8, and NO. Moreover, the study's findings imply that Cissus antractica are a potential source with biosynthesize nanoparticles that can might be further investigated for the progress of an-ti-inflammatory and anti-cancer drugs with further study.

Acemella oleracea is known as toothache plant belongs to the family of Asteraceae. It is treated as a medicinal remedy like tuberculosis, illness, cough, rheumatism, and illness. This study was concentrated on the antioxidant, cytotoxic, antimicrobial & thrombolytic activities of methanol extract of Acmella oleracea leaves using in vitro model. The antioxidant activity was estimated as trolox equivalent antioxidant capacity utilizing the DPPH and reducing power tests. The plant extract was tested for its cytotoxic action using a brine shrimp lethality bioassay, thrombolytic activity using clot disruption, and antibacterial activity using a disc diffusion assay technique against four distinct gram-positive and gram-negative bacteria. IC₅₀ value of standard ascorbic acid for DPPH was 7.8µg/ml and the IC50 of the methanol extract of Acmella oleracea leaves was 198.34µg/ml that was moderate effect at all compare with ascorbic acid. Thrombolytic assay of Streptokinase as a positive control showed 88.49% where the extract shows 18.69% lytic activity shows the assay. In this study, the sample of LC₅₀ results of cytotoxicity assay was 1.431 µg/mL which can be treated as less activity. Moreover, the extracts showed low to moderate antibacterial activity against both gram-negative and gram-positive bacterial stains (zone of inhibition-10-26 mm). Vibrio Mimicus bacteria stains exhibited the highest level of activity, with a range of 23 for the diameter of the growth inhibition zone. The current review shows leaf extracts of Acmella oleracea may be used as a source of antioxidant and thrombolytic activity, as well as a significant source of antibacterial and anticancer substances. Further research is required to evaluate in-vivo the pharmacological activity of Acmella oleracea leaves in order to identify the essential metabolites and potential mechanisms.

Methotrexate (MTX) is a potent drug for the treatment of various diseases globally amidst being a chemotherapeutic and immunosuppressant agent. However, hepatotoxicity induced by MTX could be life-threatening if left untreated. Folate supplementation is concurrently applied to reduce the adverse effects of MTX, albeit efficacy compromise. Therefore, there is the need to understand the process for the prevention and treatment strategies for MTX induced hepatotoxicity (MIH). In recent times, preliminary preclinical and clinical findings indicate the potential of natural phytobioactive compounds for MIH prevention and treatment. This mini review therefore summarizes proposed mechanisms of MIH and recent advances in the prevention and treatment prospects of natural phytobioactive compounds on MIH.

The use of plant extracts in the synthesis of metal nanoparticles is a very attractive approach in the field of green synthesis. To benefit from the potential synergy between the biological activities of the Moringa oleifera leaves extract and metallic bismuth, our study aimed at synthesizing bismuth nanoparticles using a hydroalcoholic extract of M. oleifera leaves as a means of green synthesis that yields nontoxic products and reduces the production of wasteful material. To this end, the M. oleifera leaves extract was treated with a bismuth nitrate pentahydrate solution. A color change from light brown to dark brown indicates the synthesis of bismuth nanoparticles. The total phenolic content in the M. oleifera leaves extract used was 23.0 ± 0.3 mg gallic acid equivalent/g of dried M. oleifera leaves powder. Antioxidant property of MO synthesised bismuth Nanoparticles was evaluated and in line with the extract used in the synthesis of NPs. The physical properties of the synthesized bismuth nanoparticles were characterized using UV-Vis spectrophotometer, FT-IR spectrometer, TEM, SEM, and XRD. The synthesized bismuth nanoparticles have a size in the range of 40.4-57.8 nm with amorphous morphology. Using DPPH and phosphomolybdate assays, our findings revealed that the M. oleifera leaves extract and the synthesized bismuth nanoparticles possess antioxidant properties. Using resazurin microtiter assay, we also demonstrate that the M. oleifera leaves extract and the synthesized bismuth nanoparticles exert potent anti-bacterial activity against Escherichia coli, Klebsiella pneumoniae, Staphylococcus aureus and Enterococcus faecalis, similarly to the inhibition exerted by Moringa extract, especially against Enterococcus faecalis (MIC values for the extract: 500, 250, 250, and 250 µg/mL; MIC values for the bismuth nanoparticles: 500, 500, 500, and 250 µg/mL, respectively). Similarly, the M. oleifera leaves extract and the synthesized bismuth nanoparticles display relatively stronger anti-fungal activity against Aspergillus niger, Aspergillus flavus, Candida albicans, and Candida glabrata (MIC values for the extract: 62.5, 62.5, 125, and 250 µg/mL; MIC values for the bismuth nanoparticles: 250, 250, 62.5, and 62.5 µg/mL, respectively). Thus, the hydroalcoholic extract of M. oleifera leaves was successfully used in the synthesis of bismuth nanoparticles, showing a positive antioxidant, anti-bacterial, and anti-fungal activity. Therefore, the synthesized bismuth nanoparticles can potentially be employed in the alleviation of symptoms associated with oxidative stress and in the topic treatment of Candida infections.

The synthesis of metal nanoparticles using plant extracts is a very promising method in green synthesis. The medicinal value of Moringa oleifera leaves and the anti-microbial activity of metallic copper were combined in the present study to synthesize copper nanoparticles having a desirable added-value inorganic material. The use of a hydroalcoholic extract of M. oleifera leaves for the green synthesis of copper nanoparticles is an attractive method as it leads to the production of harmless chemicals and reduces waste. The total phenolic content in the M. oleifera leaves extract was 23.0 ± 0.3 mg gallic acid equivalent/g of dried M. oleifera leaves powder. The M. oleifera leaves extract was treated with a copper sulphate solution. A color change from brown to black indicates the formation of copper nanoparticles. Characterization of the synthesized copper nanoparticles was performed using UV-Vis spectrophotometer, FT-IR spectrometer, TEM, SEM, and XRD. The synthesized copper nanoparticles have an amorphous nature and particle size of 35.8-49.2 nm. We demonstrate that the M. oleifera leaves extract and the synthesized copper nanoparticles display considerable antioxidant activity. Moreover, the M. oleifera leaves extract and the synthesized copper nanoparticles exert potent anti-bacterial activity against Escherichia coli, Klebsiella pneumoniae, Staphylococcus aureus, and Enterococcus faecalis (MIC values for the extract: 500, 250, 250, and 250 μg/mL; MIC values for the cooper nanoparticles: 500, 500, 500, and 250 μg/mL, respectively). Similarly, the M. oleifera leaves extract and the synthesized copper nanoparticles exert relatively more potent anti-fungal activity against Aspergillus niger, Aspergillus flavus, Candida albicans, and Candida glabrata (MIC values for the extract: 62.5, 62.5, 125, and 250 μg/mL; MIC values for the cooper nanoparticles: 125, 125, 62.5, and 31.2 μg/mL, respectively). Our study reveals that the green synthesis of copper nanoparticles using a hydroalcoholic extract of M. oleifera leaves was successful. In addition, the synthesized copper nanoparticles can be potentially employed in the treatment of various microbial infections due to their potent antioxidant, anti-bacterial, and anti-fungal activities.

The anti-money laundering (AML) process has failed both in identifying suspicious cases in due time as in assisting the AML analysts in decision making. Starting from a new generic anti-fraud approach, this article presents the main aspects related to the development of a multi-agent system that goes beyond the capture of suspicious transactions, seeking to assist the human expert in the analysis of suspicious behaviour. First, a transactional behavioural profile of clients is obtained in a data mining process. A set of rules, obtained through data mining over a real database, in conjunction with specific rules based on legal aspects and in the expertise of the AML analysts make up the agents' knowledge base. The cases for which the system was unable to suggest a decision are flagged as requiring more detailed analysis. The system analysed 6 months of real transactions and indicated several suspicious profiles, a set of these suspects was investigated by the AML analysts who proved the suspicion of several cases, including some that had not been identified by the systems in execution.

Several vaccines against COVID -19 have been developed and licenced to enhance the immune response against SARS-CoV-2. Similarly, infection with SARS-CoV-2 before vaccination has been shown to provide significant protection against severe infection and hospitalisation. The aim of this study was to investigate the effect of three doses of Sinopharm vaccine and SARS-CoV-2 infection on the specific immune response in 103 volunteers, measuring neutralizing antibodies, anti-S1 IgG, anti-RBD IgM, anti-N IgM, anti-N IgG antibodies and interferon γ. Our results showed that the presence of cardiovascular diseases increased the level of anti-N-IgG antibodies, while endocrinological diseases decreased the level of neutralizing antibodies and anti-N-IgG antibodies, suggesting that these diseases alter the effect of vaccine immunity. In addition, there was a significant decrease in anti-S1 IgG levels 6 months and in anti-N IgG levels 18 months post-infection, while neutralizing antibody and interferon γ levels were constant at 3, 6 and 18 months post-infection. Therefore, our results confirm the importance of hybrid immunity as the strongest and most durable compared to exclusively natural or vaccine-induced immunity. Significant positive correlations were found between humoral and cellular immunity markers: neutralizing antibodies, anti-S1 IgG, anti-N IgG and interferon γ, indicating a unique coordinated response specific to COVID-19.

This paper discusses the theoretical and experimental correlations between fatigue and static strength statistical distributions. We use a two-parameter residual strength model that obeys the qualitative Strenght-Life Equal-Rank (SLERA) assumption for guidance. The modeling approach consists of recovering the model's parameters by best fitting the constant amplitude (CA) fatigue data at a given stress ratio, R, and the experimental Weibull parameters of the static strength distribution function. Once the model's parameters are fixed, its capabilities, potential, and limits are discussed by comparing its predictions with residual strength and fatigue data obtained at different stress ratios, R. Moreover, from a preliminary analysis, the theoretical extension of the model's capabilities to variable amplitude loadings is conceptualized. The application of Miner's rule is also discussed and compared with a new damage rule to analyze the fatigue responses under variable amplitude loadings.

The aim of our study was to assess university students’ sleep quality and fatigue before and during the academic exam period and identify potential associated factors. A Web-based survey was completed by 940 students of 20 different Tertiary Institutions including demographics, sleep habits, exercise, caffeine, tobacco, alcohol use, subjective sleep quality (Pittsburgh Sleep Quality Index - PSQI) and fatigue (Fatigue severity scale – FSS) at the beginning of semester and at examination period. During exam period, PSQI (8.9 vs 6.1, p&lt;0.001) and FSS scores (36.9 vs 32.7, p&lt;0.001) were significantly elevated compared to pre-exam period. Increase of PSQI score was associated with age (β=0.111, p=0.011), presence of chronic disease (β=0.914, p=0.006), and depressive symptoms (β=0.459, p=0.001). Increase of FSS score was associated with female gender (β=1.658, p&lt;0.001), age, (β=0.198, p=0.010), increase in smoking (β=1.7, p=0.029), coffee/energy drinks consumption (β=1.988, p&lt;0.001), decreased levels of physical exercise (β=1.660, p&lt;0.001), and depressive symptoms (β=2.526, p&lt;0.001). In conclusion, our results show that sleep quality and fatigue are affected in university students during exam periods. Potential factors were identified which may lead to development of strategies for better quality of sleep, and wellbeing.

Future, flexible thermal energy conversion systems require new, demand-optimized high-performance materials. The High performance Ferritic (HiperFer) stainless steels, under development at the Institute of Microstructure and Properties of Materials (IEK-2) at Forschungszentrum Jülich GmbH in Germany, provide a balanced combination of fatigue, creep and corrosion resistance at reasonable price. This paper outlines the scientific background of alloy performance development, which resulted in an age-hardening ferritic, stainless steel grade. Furthermore, technological properties are addressed and the potential concerning application is estimated by benchmarking versus conventional state of the art materials.

The paper introduces a valuable new description of fatigue strength in relation to material properties and thus a new perspective on the overall understanding of the fatigue process. Namely, a relation between the endurance limits and the accompanying values of the critical resolved shear stress (CRSS) for various metallic materials has been discovered by means of a multiscale approach for fatigue simulation. Based on the uniqueness of the relation, there is a strong indication that it is feasible to relate the endurance limit to the CRSS, and not to the ultimate strength as often done in the past.

The Ti-6Al-4V alloy is widely used in the manufacture of components that should have low density, high corrosion resistance, and fatigue strength. The fatigue strength can be improved by surface modification. The aim of this study was to determine the influence of plasma nitriding on the fatigue behavior of Ti-6Al-4V alloy with a lamellar microstructure (Widmanstätten type). Nitriding was executed at 720 °C for 4 hours in an atmosphere with N₂, Ar and H₂. Samples microstructure characterization was carried out by X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The average roughness of the specimens was determined, and fatigue tests were executed in a bending-rotating machine with reverse tension cycles (R= -1). X-ray diffraction analysis revealed the matrix phases α and β, and the phases Ɛ-Ti₂N and δ-TiN in the nitrided alloy. A nitrogen diffusion layer was formed between the substrate and the titanium nitrides. Plasma nitriding resulted in an increase in low cycle fatigue strength, whereas at high cycles, both conditions exhibit similar behavior. The fracture surface of the fatigue tested specimens clearly revealed the lamellar microstructure. The fracture mechanism appears to be due to cracking at the interface of α and β phases of the lamellar microstructure.

The fatigue strength of the hot work steel depends on various factors, including the mechanical, properties and behavior and bulk and the surface under layer, the microstructural features as well as heat treatments. The influence of a series of heat treatments on the fatigue strength of H13 hot work steel was investigated. Different preheating, quenching and tempering treatments were applied to four sets of specimens and fatigue tests were conducted at room temperature using a rotating bending test machine. All heat treatments resulted in a certain improvement of the fatigue strength. Highest fatigue strength obtained by applying a double tempering heat treatment (first tempering at 550 °C for two hours and second tempering at 610 °C for two hours) after initial preheating and quenching. One tempering treatment (550 °C for two hours after preheating and quenching) did not significantly improve the fatigue strength.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

Across different cultures around the globe, human beings have historically depended largely on medicinal plants for managing diseases that have hitherto threatened their optimal health, survival, and longevity. Evidently, the health-derived benefits of medicinal plants can be strongly attributed to the presence of secondary metabolites, particularly polyphenols. The health-promoting effects of Sorghum bicolor supplement Jobelyn® (SBSJ) —a unique supplement derived from the leaf sheaths of a West African variety of Sorghum bicolor (L.) Moench—have also been ascribed to its high levels of polyphenols. This review seeks to gather and synthesize findings from various experimental and clinical studies on the health benefits of SBSJ in arthritis, cancer, chronic viral infections, stroke, anaemia, and aging. SBSJ has been reported to contain potent bioactive polyphenolic compounds with polyvalent biological activities, including antioxidant, anti-inflammatory, immunomodulatory, chemopreventive, and neuroprotective activities. Moreover, the probable benefits of SBSJ in chronic viral infections (e.g., HIV/AIDS and COVID-19) have been attributed to its potent anti-inflammatory and immunomodulatory activities. As this supplement is increasingly becoming one of the fastest-selling herbal medicines in Nigeria, there is a need for more robust studies (including clinical trials) in order to replicate and validate the prior insights gleaned from experimental studies.

In this paper, we investigate the effects of mean stress, multiaxial loading, and residual stresses on the fatigue life of springs. We study the fatigue life of a homogeneously stressed material subjected to cyclic loading with nonzero mean stress. Traditional methods for estimating fatigue life are based on Goodman and HAIGH diagrams. The formal analytical descriptions, namely "stress-life" and "strain-life" approaches, are found to be more suitable for the numerical methods. The fatigue analysis method described above, which describes crack growth per cycle, is extended. The extensions allow consideration of the mean stress of a load cycle. Closed-form expressions for crack length versus number of cycles are derived. The complementary effects on the fatigue life of springs, which ultimately have a significant influence on the fatigue life of springs, are summarized. For the proposed unified fatigue life functions, the ranges for the stress loading factor are extended by introducing the effective stress intensity. The solution leads to the factor range for the effective stress intensity, the effective mean value of the stress intensity factor and the effective stress ratio. The developed method assumes the homogeneous stress state in the whole spring element. For the non-homogeneously loaded structural elements, the weak-link concept is applied to account for fatigue.

In the Netherlands, the assessment of existing prestressed concrete slab-between-girder bridges showed that the thin, transversely prestressed slabs may be critical for static and fatigue punching when evaluated using the recently introduced Eurocodes. On the other hand, compressive membrane action increases the capacity of these slabs and changes the failure mode from bending to punching shear. To improve the assessment of the existing prestressed slab-between-girder bridges in the Netherlands, two 1:2 scale models of an existing bridge, the Van Brienenoord Bridge, were built in the laboratory and tested monotonically as well as under cycles of loading. The result of these experiments is: 1) the static strength of the decks, showing that compressive membrane action significantly enhances the punching capacity, and 2) the Wöhler curve of the decks, showing that compressive membrane action remains under fatigue loading. The experimental results can then be used for the assessment of the most critical existing slab-between-girder bridge. The outcome is that the bridge has sufficient punching capacity for static and fatigue loads, and thus that the existing slab-between-girder bridges in the Netherlands fulfil the code requirements for static and fatigue punching.

This study investigates the effects of ambient illumination and negatively polarized text color on visual fatigue, exploring the issue of visual fatigue when using visual display terminals in low-illumination environments. The research methodology utilized an experimental design to collect data on changes in pupil accommodation and blink rate through an eye tracker. Partici-pants completed a reading task while exposed to various text colors and ambient light conditions to evaluate visual fatigue and cognitive performance. The study's findings suggest that text color significantly affects visual fatigue, with red text causing the highest level of visual fatigue and yellow text causing the lowest level of visual fatigue. Improvements in ambient lighting reduce visual fatigue, but the degree of improvement varies depending on the text color. Additionally, cognitive performance is better when using yellow and white text but worse when using red text. Yellow text is the most effective choice for reducing visual fatigue under negative polarity. In-creasing ambient lighting can also improve visual fatigue in low-illumination conditions. These findings will offer valuable guidance for designing visual terminal device interfaces, especially for low-illumination or night environments, to minimize visual fatigue and improve the user ex-perience.

Self-report measurement is frequently used in human sports to assess training adaptations [1, 2]. This is a technique novel to the equestrian sport. The aim of this study was to describe how elite event riders of Germany evaluate their own fitness as well as that of their horses for the entire duration of an eventing season. Additionally, correlations with possible influencing external factors such as type of training or duration of grazing were also investigated. Short online questionnaires were used to allow eight riders to describe the training of their horses. Five criteria (general performance, ability to concentrate, general state of mind, general muscular condition and emotional wellbeing) were used to assess both, their horse's, as well as their own wellbeing. A 1-10 rating scale was used to score each criterion resulting in an average of 38 points out of 50 (maximum wellbeing) for horse (Std. dev. 0.55) and rider (Std. dev. 0.65) respectively. A total of 120 questionnaires were analysed. A correlation could be demonstrated (Spearman's correlation coefficient = 0.5) between rider and horse score, whereby it only became a linear correlation above 30 points. In addition, the horse score correlates positively with its success at competitions. While the horses were rated similarly throughout the season, the riders’ perceived welfare was higher in the middle of the season compared with the beginning and end of the season. Regularly turned-out horses resulted in higher horse scores (Linear mixed model, p=0,04, n=120). It can be concluded that the self-report measurement of fatigue and wellbeing can be a useful tool for trainers and riders to better determine the horse’s fatigue and recovery. It should be noted that external factors influence both, rider and horse assessment.

The present study focuses on the investigation of fatigue, social support and quality of life that characterizes social workers. Furthermore, the study aims to highlight the effect of demographic and occupational characteristics on the above factors. A total of 400 social workers with an average age of 39.05 years took part in the research. Most were women, single, residents of cities of more than 100,000, and health care workers. Participants were asked to answer online questionnaires (FAS for fatigue, MSPSS for social support and GHQ-28 for quality of life). From the analysis of the data, it was found that the level of fatigue of the social workers is at low levels. At the same time, the level of occurrence of negative symptoms is also low, with physical symptoms appearing more often than the rest. Participants receive a high level of support from their environment, and more so from the "significant other" in their life. Finally, it was found that the fatigue, social support and quality of life of social workers is affected by the age of the social workers, the total years of service, gender, marital status, place of residence, employer and position of responsibility.

The high demands of caring for and raising a child with autism spectrum disorder on a daily basis fatally lead parents to the appearance of physical and mental fatigue. This study aimed to assess the effect of social support and spirituality on the fatigue of parents with children with autistic spectrum disorder. A cross-sectional study with a convenience sample was conducted in Schools of Special Education in Attica (Greece). The sample consisted of 123 parents who completed The Fatigue Assessment Scale (FAS), the Multidimensional Scale of Perceived Social Support (MSPSS), and the Functional Assessment of Chronic Illness Therapy Spiritual Well-Being Scale (FACIT Sp-12) to measure the levels of fatigue, social support, and spirituality, respectively. Demographic data were, also, recorded. Data analysis was applied using IBM SPSS 21.0. The mean age was 47.3 years old, 81.3% were women, and 38.9% stated much / very much religious. The mean of total FAS was 28.4 (SD±7.5), of total FACIT Sp-12 was 31.5 (SD±8.7), and of total MSPSS 5.1 (SD±1.1). Higher levels of total MSPSS and FACIT Sp-12 were associated with lower total FAS (r= -0.50, p &lt;0.001 and r= -0.49, p&lt;0.001 respectively). Social support and spirituality are significant predictors of fatigue.

The purpose of this study was to identify subgroups of quality of life (QOL) changes in breast cancer survivors (BCS) and to determine factors associated with subgroups of consistently low or deteriorated QOL. We enrolled 101 women recently diagnosed with breast cancer in South Korea and asked them to complete a questionnaire at baseline (within 1 month of diagnosis), 1 year later (Year 1), 2 years later (Year 2), and 3 years later (Year 3). We assessed QOL using the global QOL subscale from the EORTC QLQ-C30. We defined low QOL as a global QOL score 10 points below the mean score of the general population. Based on low QOL as defined in this study, we identified subgroups of QOL changes over 3 years. We identified four subgroups of QOL changes: improved (47.4%), stable (30%), continuously low (8.8%), and deteriorated (13.8%) and considered the last two categories (22.6%) as poor QOL. Logistic regression analyses demonstrated that significant determinants of poor QOL were insomnia at Year 1, fatigue and anxiety at Year 2, and fatigue, depression, and comorbidity at Year 3. In conclusion, persistent symptoms of insomnia, fatigue, anxiety, depression, and comorbidity are potential risk factors for poor QOL in BCS.