For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

Accurately estimating shrub biomass in arid and semi-arid regions is critical for understanding ecosystem productivity and carbon stocks at both local and global scales. However, capturing the shrub biomass accurately by satellite observations is challenging due to the short and sparse features of shrubs. In this study, we presented a framework to estimate shrub biomass at a 10m spatial resolution by integrating ground in-situ data, unmanned aerial vehicle (UAV), Sentinel-2, and Sentinel-1 observations. The pilot study was conducted in the Helan mountains of Ningxia province, China. First, the spatial distribution map of shrubland and other land cover types was generated in 2023. Then, a prediction model of shrub biomass was developed in a Random Forest Regression (RFR) approach driven by different predicted variable datasets based on in-situ measurements, UAV, and satellite images. Finally, the developed model was used to produce the biomass map of shrubland in 2023. The uncertainty was characterized by creating a standard deviation (SD) map using the Leave-One-Out Cross-Validation (LOOCV) method in the shrub biomass estimates. The resultant shrubland distribution map in 2023 has an F1 score of 0.92. The shrub biomass model driven by spectral bands and vegetation indices (R2= 0.62) demonstrated superior performance than that only driven by spectral bands (R2=0.33) or vegetation indices (R2=0.55). The uncertainty of the estimated biomass was lower than 4%, with the lowest values (<2%) happening in the high shrub coverage (>30%) and biomass production (>30kg/m2) regions. Furthermore, the findings show that the magnitude of shrub biomass was affected by the aridity and precipitation significantly in the study region. This study provides a workflow to accurately monitor the biomass of shrublands in a complicated environment based on remote sensing images from multi-platform observations.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

The expanding global population has increased the demand for sustainable protein sources, and microbial protein (MP) has emerged as a promising alternative. However, conventional carbon (glucose) and nitrogen (ammonia, urea) sources needed for MP production pose environmental and economic issues. This study aims to produce protein using lignocellulosic biomass (LCB) as a carbon source and the nitrogen fixation ability of Klebsiella oxytoca M5A1 as a nitrogen source. The study investigates the pretreatment of LCB (switchgrass), enzymatic hydrolysis, protein quantification, and high-performance liquid chromatography system (HPLC) analysis to track glucose utilization and organic acid production. K. oxytoca M5A1 harnessed free nitrogen from the atmosphere through nitrogen fixation and used abundant, cheap glucose from LCB to produce MP and organic acids as by-products. Protein production occurred in two phases: first within the initial 8 hours and secondly, within the last 16 hours. The highest protein concentration was at 40 hours, with approximately 68.3% protein content. HPLC analysis revealed a dynamic profile of glucose utilization and organic acids (Lactic acid, Propionic acid, Acetic acid, and Succinic acid). K. oxytoca M5A1 exhibited an early high rate of glucose consumption, and conversion to organic acids that were later used for second-phase protein production. The acids profile revealed intra-conversion from one acid to another via metabolic pathways (glycolysis and tricarboxylic acid cycle). Overall, leveraging LCB and the nitrogen-fixing ability of K. oxytoca M5A1 for MP production offers an eco-friendly and cost-effective alternative to traditional protein sources, contributing to a sustainable circular economy.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

Lignocellulosic biomass has garnered attention as an abundant and sustainable alternative energy source that can facilitate reliable and environmentally friendly energy generation. Energy security improves, and environmental impacts diminish when bioethanol, a biofuel produced via lignocellulose-based processes, is utilized. The lignocellulosic biomass of Thysanolaena latifolia has considerable potential as a bioethanol feedstock due to its high carbohydrate content (62.4 ± 0.7%). In this study, feedstock derived from T. latifolia was pretreated with various concentrations of H3PO4 to determine the ideal conditions for enzymatic hydrolysis to convert the feedstock to fermentable sugar. The findings revealed that hydrolysis efficiency and glucose recovery yields were substantially improved compared to those of the untreated sample. Pretreated samples were enzymatically digested to produce a liquid hydrolysate. This hydrolysate was fermented without detoxification using Saccharomyces cerevisiae TISTR 5339 to produce ethanol. The results indicated that T. latifolia biomass hydrolysate is a promising long-term carbon source for ethanol production from cellulosic biomass. Furthermore, the morphological and crystallographic characteristics of the treated T. latifolia biomass were influenced by H3PO4 concentration, as indicated by the SEM images, X-ray diffractogram patterns, and crystallinity index values. Therefore, utilizing T. latifolia feedstock to produce bioethanol can enhance bioenergy sustainability.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

A non-destructive analysis of proximate parameters (moisture content, MC; volatile matter, VM; fixed carbon, FC; and ash content) for a variety of chipped and ground biomasses was investigated through a combination of thermogravimetric analysis (TGA) and near-infrared spectroscopy (NIRS) with partial least squares regression (PLSR). In this study, the thermogravimetric method was employed as a tool to determine the proximate analysis data of biomass samples through TG and DTG curves, which were generated by tracking changes in biomass mass loss over time or temperature. NIRS non−destructively scanned the chipped biomass in diffuse reflectance while ground biomass using transflectance mode, covering the wavenumber range of 3594.87 to 12,489.48 cm−1. The PLSR−based models: Full−PLSR, genetic algorithm (GA)−PLSR, successive projection algorithm (SPA)−PLSR, the spectral multi−preprocessing (MP) PLSR− 5 range method, and the MP PLSR−3 range method were developed. Model performance was assessed, compared, and selected based on the coefficient of determination in the prediction set (R2P), root mean square error in the validation set (RMSEP), and the ratio of prediction to deviation (RPD). Based on the comprehensive analysis of model performance, MC and FC models of chip biomass have demonstrated satisfactory performance which makes it applicable cautiously in any application, including research. The optimum models for MC and FC in chip biomass were constructed using GA−PLSR with 2nd derivative and Full−PLSR with a constant offset, resulting in R2P values of 0.8654 and 0.8773, RMSEP values of 0.85% and 2.12%, and RPD values of 2.9 and 3.0, respectively. Other parameters such as MC and FC in ground biomass as well as VM and ash content in both chip and ground biomass were found suitable for rough screening. The sensitivity of the selected model was assessed by calculating the limit of quantification (LOQ), and the results indicated that the calculated LOQ values for VM in both chip and ground biomass and FC in chip biomass are lower than the minimum reference values used during model development, signifying a high level of sensitivity. However, for the remaining parameters, the LOQ values surpass the established minimum reference value, suggesting the model could not predict the future samples with reference value lower than the calibration range. Nevertheless, enhancing the models by incorporation an ample number of representative biomass samples and consistently validating the models with unknown samples is imperative to ensure accurate predictions.

The present study aimed at utilizing technically hydrolyzed lignin (THL), industrial biomass residue, derived in high-temperature diluted sulphuric acid hydrolysis of softwood and hardwood chips to sugars. The THL was carbonized in horizontal tube furnace at atmospheric pressure, in inert atmosphere and at three different temperatures (500, 600 and 700 ºC). Biochar chemical composition was investigated along with its HHV, thermal stability (thermogravimetric analysis) and textural properties. Surface area and pore volume were measured with nitrogen physisorption analysis often named upon Brunauer–Emmett–Teller (BET). Increasing the carbonization temperature reduced volatile organic compounds (40 ÷ 96 wt. %), increased fixed carbon (2.11 to 3.68 times the wt. % of fixed carbon in THL), ash and C-content. Moreover, H and O were reduced, while N- and S-content were below the detection limit. This suggested biochar application as solid biofuel. The biochar Fourier-transform infrared (FTIR) spectra revealed that the functional groups were gradually lost thus, forming materials having merely polycyclic aromatic structures and high condensation rate. The biochar obtained at 600 and 700 ºC proved having properties typical for microporous adsorbents, suitable for selective adsorption purposes. Based on the latest observations another biochar application was proposed - as catalyst.

The production of biomass fly ash has been increasing every year in Europe, reaching 5.5 million tons in 2020. Biomass fly ash is not yet accepted in the standards as a substitute material for cement in mortar and concrete. In a first approach, the substitution limit of biomass fly ash is determined by comparing the mechanical strengths, fresh state properties and hardened properties of mortars produced with biomass fly ash to those of mortars produced with classical coal fly ash. Then, masonry and rendering mortars have been designed with different substitution rates of biomass fly ashes from wood combustion in thermal power plant. Although there is an overall decrease in performance, mortars made with biomass ash retain properties that make them suitable for use in masonry or rendering.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry and high performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than that of the original biomass (higher heating value of Eucalyptus sawdust bio-oil 29 MJ/kg versus 19.5 MJ/kg of the original Eucalyptus sawdust). The analyses of the bio-oils allowed to identify the presence of high added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of the liquefied biomass showed that the biofuel density increases with the storage time due to the occurrence of repolymerization reactions.

Bifunctional catalysts consisting of mono- or bimetallic nanoparticles (NPs) and zeolite supports received considerable attention due to excellent catalytic properties in numerous reactions including direct and indirect biomass processing. Here, we discuss major approaches to the preparation of NPs in zeolites, concentrating on methods allowing the best interplay (synergy) between metal and acid sites which is normally achieved for small NPs well-distributed through zeolite. We focus on modification of zeolites to provide structural integrity and controlled acidity which can be accomplished by incorporation of certain metal ions or elements. The other modification avenue is the adjustment of the zeolite morphology including creation of numerous defects for the NP entrapment and designed porosity. In this review we also provide examples of synergy between metal and acid sites and emphasize that without density functional theory calculations many assumptions about interactions between active sites stay unvalidated. Finally, we describe the most interesting examples of direct and indirect biomass (waste) processing for the last five years.

Wet anaerobic storage of algal biomass is a promising preservation approach which can ensure continuous supply of these feedstocks to biorefineries year-round. An effective solution to preservation must ensure minimal dry matter loss and change in biochemical composition during storage. Therefore, the objective of this study was to investigate the preservation of Nannochloropsis gaditana biomass through wet anaerobic storage and its impact on biomass quality. Prior to storage, algae sample was inoculated with two different strains of lactic acid bacteria and thereafter stored for 30 and 180 days. Each inoculant limited dry matter loss to &lt;10% (dry basis) after the storage durations. Final pH values (4.3 - 4.8) indicate that the biomass samples were properly ensiled, achieving the acidic conditions necessary for preservation. Compositional analysis of the biomass after storage showed a reduction in carbohydrate content, a relative increase in lipid content, and no significant change to the protein fraction. Glucose and galactose were the prevalent sugar monomers. The low dry matter loss and minimal compositional change indicates that wet anaerobic storage is an effective means of preserving algal biomass, ensuring a constant supply of algal biomass feedstock to a biorefinery.

In the end, this paper analyzed the economy from the investment in plant construction, raw material collection, product production and product sales. The resulting products include pyrolytic carbon, pyrolytic oil, pyrolysis gas. The results showed that when the treatment scale was 1 ton h−1, the pyrolysis plants with three loading modes will always be in a state of loss during the 20-year running time. When the processing scale was 9 ton h−1, the pyrolysis plant can be profitable in the first year. In the sensitivity analysis, the influence of three pyrolysis products on the total return on investment was explored. The results showed that the price change of pyrolysis oil has the greatest influence on the total return on investment (Total ROI) under the three loading methods, The price change of pyrolysis gas has minimal impact on the Total ROI. This study provides basic data and basis for the commercialization of coal-biomass co-pyrolysis technology and investment in plant construction.

Net CO2 emissions and sequestration from European forests are the result of removal and growth of flora. To arrive at aggregated measurements of these processes at a country's level, local observations of increments and harvest rates are up-scaled to national forest areas. Each country releases these statistics through their individual National Forest Inventory using their particular definitions and methodologies. In addition, five international processes deal with the harmonization and comparability of such forest datasets in Europe, namely the IPCC, SOEF, FAOSTAT, HPFFRE, FRA (definitions follow in the article). In this study, we retrieved living biomass dynamics from each of these sources for 27 European Union member states. To demonstrate the reproducibility of our method, we release an open source python package that allows for automated data retrieval and analysis, as new data becomes available. The comparison of the published values shows discrepancies in the magnitude of forest biomass changes for several countries. In some cases, the direction of these changes also differ between sources. The scarcity of the data provided, along with the low spatial resolution, forbids the creation or calibration of a pan-European forest dynamics model, which could ultimately be used to simulate future scenarios and support policy decisions. To attain these goals, an improvement in forest data availability and harmonization is needed.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

Assessing the economic supply of biomass in a geospatial context while accounting for risk from natural disasters was studied. Risk levels were estimated from a component of factors which included: population density, road density, federal ownership, U.S. Environmental Protection Agency ecoregions, and Presidential Disaster Declarations. The Presidential Disaster Declarations included risks due to: coastal storm, drought, fire, flood, freezing, hurricane, mud land slide, severe ices, severe storms, snow, tornado, and tropical storm. Presidential Disaster Declarations included summaries based on a short-term time period from 2000-2011, and on a long-term time period from 1964-2011. Risk categories were developed as a function of the number of disaster declarations, agricultural-to-forest land ratio, average road density, and average population density. A significant contribution of the research was the allocation of spatially explicit data using GIS technology at the 5-digit zip code tabulation area. The average area for 5-digit ZCTAs in the Eastern U.S. study region was approximately 169 kilometers². Long-term risk (1964-2011) from disaster declarations had a greater impact on the economic availability of biomass supply relative to short-term declarations (2000-2011). The greatest risk to biomass supply came from population density relative to the other risk factors studies. Of the 25,044 total ZCTAs, 12,256 ZCTAs were in locations that did not include population density ≥ 150/km², road density ≥ 14 km/km², federal ownership, and US Environmental Protection Agency Level III ecoregions. Of the remaining 12,256 ZCTAs, 26.8% were considered to be moderate-to-high risk based on short-term declarations (2000-2011) and 29.4% were considered to be moderate-to-high risk based on long-term declarations (1964-2011). Lower risk locations for procuring biomass supply for both short-term and long-term declarations, across all risk factors, were in southern Georgia, South Carolina, and Texas.

Microalgae have emerged as potential feed stock for third generation biofuel and other bioactive compounds. In the present investigation we have evaluated the two native strains of Oscillatoria (O. subbrevis MTC-20702 and O. sancta MTC-20703) isolated from two different fresh water biotopes of Meerut, U.P., India and were subjected for the characterization of generation time, biomass, bio-molecules including Chlorophyll-a, carotenoids, carbohydrate, lipids, phycobilins and proteins. Both strains of Oscillatoria were grown in batch culture till the initiation of declining phase and were harvested on every 10th day of incubation till the starting of declining phase. Result of the present investigation revealed that O. subbrevis MTC-20702 can be potentially exploited for the production of high algal biomass, feed stock for biofuel, Chl-a, carotenoids, c-Allophycocyanin and maximum yield of these bioactive compounds can be achieved on 20th day. However, O. santa could be very good source for c-Phyocyanin, c-Phycoerythrin, carbohydrate and protein and these also can be achieved highest on 20th day of incubation. In addition, as these two strains were isolated from water reservoirs and they can be cultivated in large scale for the production of desired bio-molecules.

The emergence of cloud computing, big data analytics, and machine learning has catalysed the use of remote sensing technologies to enable more timely land management of sustainability indicators such as ground cover and grassland biomass, given the uncertainty of future climate and drought conditions. Here, we examine the potential of “regenerative agriculture”, as an adaptive grazing management strategy to minimise bare ground exposure while maximising pasture biomass productivity. High-intensity sheep grazing treatments were conducted in small fields (less than 1 hectare) for short durations (typically less than 1 day). Paddocks were subsequently spelled to allow pasture biomass recovery (treatments comprising 3, 6, 9, 12, and 15 months) with each compared with control treatments with lighter stocking rates for longer periods (2,000 DSE). Pastures were composed of wallaby grass (Austrodanthonia species), kangaroo grass (Themeda triandra), Phalaris (Phalaris aquatica, and cocksfoot (Dactylis glomerata) were destructively sampled to estimate total standing dry matter (TSDM), standing green biomass, standing dry biomass and trampled biomass. We then invoked a machine learning model using Sentinel-2 imagery to quantify TSDM, standing green biomass and standing dry biomass. Faced with La Nina conditions, regenerative grazing did not significantly impact pasture productivity, with all treatments showing similar TSDM and green biomass. However, regenerative treatments significantly impacted litter fall and trampled material, with the high intensity grazing treatments causing more dry matter trampling, increasing litter, enhancing decomposition rates and surface organic matter. Pasture digestibility was greatest for treatments with minimal spelling (3 months), whereas both standing senescent and trampled material were significantly greater for the treatment with 15-month spell periods. Estimates of TSDM using machine learning with Sentinel-2 imagery underestimated TSDM in treatment plots but explained spatiotemporal variability associated within and across treatments. The root mean square error between the measured and modelled TSDM was 903 kg DM/ha, which was less than the variability measured in the field. We conclude that regenerative grazing with short recovery periods (3-6 months) are most conducive to increasing pasture production under high rainfall conditions, and we speculate that high intensity grazing is likely to positively impact on soil organic carbon through increased litterfall and trampling. Our study paves the way forward for using machine learning with satellite imagery to quantify pasture biomass at small scales, enabling management of pastures from afar.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

In terms of sustainability, there is a pressing need to evaluate agricultural and forestry leafy biomass that has no current economic value or may pose a threat to the environment. In this aspect, leafy biomass, which represents around 5% of the total tree, can be used for purposes that would be more profitable and ecofriendly. To this end, biorefinery of leafy biomass in the way of extracting valuable health compounds such as phenolics would ensure a valuable societal health ingredient besides alleviating waste disposal problem. However, during the biorefinery process, the primary challenges start with ensuring the feedstock to produce phenol rich leaves extract followed by their isolation and commercialization of this leaves extract. This current review aims to detail the types of biomasses, biorefinery approach of leafy biomass towards the phenolic extraction, leaves commercialization followed by the marketing strategy of the application of phenol rich leaves extract. The outcome of this overview will serve researchers and relevant industries in understanding the process for feedstock collection and the suitable sectors to apply leafy biomass derived healthy compounds.

Pyrolysis is a thermochemical conversion process designed for biomass decomposition in an oxygen-free environment. It typically operates within a temperature window of 200 to 800°C and generates various byproducts, including gases, liquid fractions (both aqueous and organic) such as bio-oil, and solids like char. Bio-oil is a significant product of pyrolysis. It is characterised by a complex blend of organic compounds. The acidic nature of bio-oil primarily originates from volatile acids, such as acetic acid. The recovery of acetic acid from bio-oil facilitates the use of the extracted substance as a precious resource, hence enhancing its significance in the framework of a circular bioeconomy. Acetic acid finds widespread application in manufacturing commercially important chemicals like vinyl acetate monomers and formulating phytosanitary products due to its inherent herbicidal and antifungal properties. However, to be used, acetic acid has to be separate from the raw bio-oil. Separation methodologies, including nanofiltration and reverse osmosis, demonstrate potential in recovering acidic constituents from bio-oil due to their high selectivity and effective system management. This article offers a concise review about acetic production from lignocellulosic biomass from pyrolysis and its recovery through various membrane separation processes.

The exploitation of bio-based foams implies an increase in the use of renewable biological resources to reduce the rapid consumption of petroleum-derived resources. Both tannins and furfuryl alcohol are derived from forestry resources and are therefore considered as attractive precursors for the preparation of tannin-furanic foams. In addition, toughening modification of tannin-furanic foams using polyvinyl alcohol (PVOH) resulted in a more flexible network-like structure, which imparts excellent flexibility to the foams with acquirement of relative properties that are even close to those of polyurethane foams, which are the most used polymers for fabrication of insoles for athletes. In addition, the addition of PVOH did not affect the thermal insulation of the foams, resilience and elongation at break, while reducing the brittleness of the samples and improving the mechanical properties. Also the observation of the morphology of the foam indicated that the compatibility between PVOH and tannin-furanic resin is good, and the cured foam does not show fragmentation or collapse, while the bubble pore structure is uniform. The developed flexible foam derived from biomass resources endowed the foam good thermal insulation properties and high mechanical properties, and the samples exhibited suitable physical parameters to be used as flexible insoles for athletes.

The aim of this research was to test recent developments in the use of Remotely Piloted Aircraft Systems or Unmanned Aerial Vehicles (UAV) to map pasture biomass yield and nutrient status, across a selected range of field sites throughout the rangelands of Queensland. Improved pasture management begins with an understanding of the state of the resource base, UAV based methods can potentially achieve this at improved spatial and temporal scales. This study developed predictive models of both pasture yield and pasture nutrient status. An automated pasture height surface modelling technique was developed, tested and used along with field site measurements of pasture yields, to predict further estimates across each field site. Both prior knowledge and automated predictive modelling techniques were employed to predict pasture yield and nutrition. Pasture height surface modelling was assessed against field measurements using a rising plate meter, results reported correlation coefficients (R2) ranging from 0.2 to 0.4 for both woodland and grassland field sites. Accuracy of the predictive modelling was determined from further field measurements of pasture yield and on average indicated an error of 0.8 t ha-1 in grasslands and 1.3 t ha-1 in mixed woodlands across both modelling approaches. Correlation analyses between measures of pasture quality, acid detergent fibre and crude protein (ADF, CP), and spectral reflectance data indicated the visible red (651 nm) and red-edge (759 nm) regions were highly correlated (ADF R2 = 0.9 and CP R2 = 0.5 mean values). These findings agreed with previous studies linking specific absorption features with grass chemical composition. These results conclude that the practical application of such techniques, to efficiently and accurately map pasture yield and quality, is possible at the field site scale, however further research is needed, in particular further field sampling of both yield and nutrient elements across such a diverse landscape, with the potential to scale up to a satellite platform for broader scale monitoring.

The present article discusses the institutional model adopted in Brazil regarding energy production through biomass. The theoretical-empirical method is used to conclude that the model's difficulties can be overcome by adopting a network of contracts capable of subjecting renewable energy generation to an energy compensation model.

The case for demand-driven research and development has received important considerations among governments, donors and programme implementing partners in development planning and implementation. Addressing demand is believed to be a bottom-top approach for designing and responding to development priorities and is good for achieving development outcomes. In this paper, we discuss the concept and application of demand driven research for development (DDRD) in Africa. We use evidence of six projects implemented under the BiomassWeb Project in Africa. We focus on parameters on level of engagement of stakeholders - whose demand is being articulated, the processes for demand articulation, capacity building and implementation processes, innovativeness of the project, reporting and sustainability of the project. We find that the nature of the institutions involved in articulation and implementation of demand-driven research and development projects and their partnerships influence the impact and reporting of demand-driven projects.

According to the IPCC guidelines, CO₂ emissions from biomass should be excluded from the entire amount of CO₂ emissions when calculating CO₂ emissions and should be separately reported due to the “carbon neutrality.” Sewage sludge is one of the representative biomass fuels. And it is mixed with fossil fuels in terms of greenhouse gas reduction or is used as fuel to replace fossil fuels by itself. According to the results of this study, biomass contents of both the sewage sludge and the sewage sludge incineration exhaust gases did not amount to 100%. At present, in many countries(South Korea, Japan, and Germany), when calculating greenhouse gas emissions from sewage sludge incinerator, all CO₂ emissions from sewage sludge are judged to be biomass and only those greenhouse gas emissions that correspond to Non-CO₂ gases are calculated as greenhouse gas emissions. However, since, according our results, the content of sewage sludge is not 100% biomass, if CO₂ emissions are excluded according to the existing greenhouse gas emission calculation method, the amount of emissions may be underestimated. Therefore, to accurately calculate greenhouse gas emissions from sewage sludge incinerator, CO₂ emissions should be calculated in consideration of the fossil carbon contents of sewage sludge.

Lake Malombe fish stocks have been depleted by chronic overfishing. Various management approaches (co-management, command control, and ecosystem-based management to fisheries) have been used to manage the fishery. However, the lack of an accurate predictive model has hampered their success. Therefore, we developed and tested a time series model for Lake Malombe fishery. The seasonal fish biomass and CPUE trends were first observed and both were non-stationary. The second-order differencing was applied to transform the non-stationary data into stationary. Autocorrelation functions (AC), partial autocorrelation function (PAC), and Akaike information criterion (AIC) were estimated, which led to the identification and construction of autoregressive integrated moving average (ARIMA) models, suitable in explaining the time series and forecasting. The results showed that ARIMA (1,2,1) provided a better prediction than its counterparts. The model satisfactorily predicted that by 2032, both fish biomass and CPUE will decrease to 3204.6 tons and 59.672 respectively, signifying the potential threat to Lake Malombe fishery. The model justified the necessity of taking precautionary measures to avoid the total collapse of the fishery.

Based on recent interest and on the importance of the ongoing climate change catastrophe, this article provides the basics of global carbon cycle modelling as required for the assessment of the degree of carbon neutrality of biomass energy, and its underlying dynamics. It is aimed at clari-fying the question “Are biomass fuels carbon neutral?”. The "Combined Energy and Biosphere Model" (CEBM) computes annual carbon flows including growth and decay of plants on 2.52.5° grid elements of the continents’ surface and offers detailed results on the changes of after implementation of large-scale biomass energy strategies world-wide. The main (and possibly unexpected) effect is the long-term depletion of the soil organic compartment after extraction of biomass fuels. When comparing CEBM model runs using (i) biomass energy sources and (ii) carbon-free energy sources (such as solar or wind), it becomes quantitatively clear already on the theoretical level (i.e., even without taking into account effi-ciency losses) that biomass is only “half as carbon neutral” as ideally assumed, to express a rule of thumb – mainly because of soil carbon depletion. Still, biomass energy will play an important role when fighting global warming, even if efforts to lower energy demand are preferable as a fundamental strategy.

Biomass gasification acquired great interest over the past decades as an effective and trustable technology to produce energy and fuels with net-zero carbon emissions. Moreover, using biomass waste as feedstock enables to recycle organic wastes and to fit the circular economy goals thus reducing the environmental impacts of waste management. Even if many studies have been already carried on, this kind of process must still be investigated and optimized with the final aim to develop industrial plants for different applications, from the hydrogen production to net-negative emission strategies. Modeling and developing of process simulations became an important tool to investigate the chemical and physical behavior of the plant, allowing to make a first raw optimization of the process and to define heat and material balances of the plant as well as to define optimal geometrical parameters with cost and time effective approaches. The present review paper focuses on the main literature models developed until now to describe biomass gasification process, and in particular on kinetic models, thermodynamic models, and computational fluid dynamic models. The aim of this study is to point out the strengths and the weakness of those models, comparing them and indicating in which situation is better to use an approach instead of another. Moreover, theoretical shortcut models and software simulations, not explicitly addressed by prior reviews, are taken into account. For researchers and designers this review provides a detailed methodology characterization as a guide to develop innovative study or project.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

Chaparral shrublands are the dominant wildland vegetation type in southern California and the most extensive ecosystem in the state. Disturbance by wildfire and climate change have created a dynamic landscape in which biomass mapping is key in tracking the ability of chaparral shrub-lands to sequester carbon. Despite this importance, most national and regional scale estimates do not account for shrubland biomass. Employing plot data from several sources, we built a random forest model to predict above ground live biomass in southern California using remote sensing data (Landsat NDVI) and a suite of geophysical variables. By substituting the NDVI and precipi-tation predictors for any given year we were able to apply the model to each year from 2000-2019. Using a total of 980 field plots, our model had a k-fold cross validation R2 of 0.51 and a RMSE of 3.9. Validation by vegetation type ranged from R2 = 0.17 (RMSE=9.7) for Sierran mixed conifer to R2 = 0.91 (RMSE = 2.3) for sagebrush. Our estimates showed an improvement in accuracy over a two other biomass estimates that included shrublands, with an R2 = 0.82 (RMSE = 4.7) compared to R2 = 0.068 (RMSE = 6.7) for a global biomass estimate and R2 = 0.29 (RMSE = 5.9) for a regional biomass estimate. Given the importance of accurate biomass estimates for resource managers we calculated the mean year 2010 shrubland biomass for the four national forests which ranged from 3.5 kg/m2 (Los Padres) to 2.3 kg/m2 (Angeles and Cleveland). Finally, we compared our estimates to field-measured biomass from the literature summarized by shrubland vegetation type and age class. Our model provides a transparent and repeatable method to generate biomass measure-ments in any year, thereby providing data to track biomass recovery after management actions or disturbances such as fire.

Many corporations aspire to become Net Zero Carbon Dioxide by 2030-2050. This paper examines what it will take. It requires understanding where energy is produced and consumed, the magnitude of CO2 generation, and the Carbon Cycle. Reviews are provided for prior technologies for reducing CO2 emissions from fossil to focus on their limitations and to show that none offer a complete solution. Both biofuels and CO2 sequestration reduce future CO2 emissions from fossil fuels. They will not remove CO2 already in the atmosphere. Planting trees has been proposed as one solution. Trees are a temporary solution. When they die, they decompose and release their carbon as CO2 to the atmosphere. The only way to permanently remove CO2 already in the atmosphere is to break the Carbon Cycle by growing biomass from atmospheric CO2 and sequestering biomass carbon. Permanent sequestration of leaves is proposed as a solution. Leaves have a short Carbon Cycle time constant. They renew and decompose every year. Theoretically, sequestrating a fraction of the world’s tree leaves can get the world to Net Zero without disturbing the underlying forests. This would be CO2 capture in its simplest and most natural form. Permanent sequestration may be achieved by redesigning landfills to discourage decomposition. In traditional landfills, waste undergoes several stages of decomposition, including rapid initial aerobic decomposition to CO2, followed by slow anaerobic decomposition to methane and CO2. The latter can take hundreds to thousands of years. Understanding landfill chemistry provides clues to disrupting decomposition at each phase.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

Distinguishable annual growth rings produce in Pinus roxburghii are an asset to find out the age of individual tree. This paper aimed to determine the age of P. roxburghii through coring samples and test the relationship with forest production. The biomass estimated, girths measured at two different sections and heights measured which allowed to determine the rate of tapering of the stand. The regression analysis was performed to test the relationship between various variables. The mean age of the P. roxburghii stand was found to be 23.97 (~24 years). The result showed the significant (p<0.05) positive correlation coefficient has been seen between age with girth at breast height, biomass, volume and carbon stock. However, no significant (p>0.05) correlation (r = 0.08) was found between age and height of the stand. In contrast, a correlation between diameter at breast height (DBH) was significant (p<0.05) and positive with volume, biomass, but no significant (p>0.05) correlation (r = 0.14) found between DBH and height of the stand. However, height has a significant (p<0.05) positive correlation with biomass. The mean biomass was 375 kg and mean annual increment (MAI) was 15 kg per tree. Rate of tapering of the studied stand predicted to be 3 cm diameter decreased with trunk height running at 100 cm from base to upward of P. roxburghii stand and vice versa. Result suggests that height-age relation is very weak whereas age, DBH, biomass and carbon has a significant correlation signifies that time-based forests' production and potential production estimation can be obtained in a relatively accurate way by utilizing the age of stand. The time-based forest production analysis is pioneer work in Nepal. The study affirms the tree ring count in P. roxburghii would be a credible and accurate method to determine the age of standing trees.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T1 = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T2 = 50 kg N ha^-1, T3 = 100 kg N ha^-1 and T4 = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T5: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T6: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T7: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO2 concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T6 = Split N100) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

Biogeochemical models estimate soil organic carbon (SOC) sequestration, crop growth, and yield. The DeNitrification and DeComposition (DNDC) model was used to simulate soil SOC dynamics and harvested C-biomass in rice-wheat rotation under organic/inorganic fertilizations with conventional tillage (CT) and reduced tillage (RT). Before calibration, DNDC under-predicted harvestable grain C-biomass of rice by 29.22% to 42.14% and over-simulated grain C-biomass of wheat by 55.01% with equal amounts of NPK and animal manure applied under CT. However, after calibration by adjusting default values of soil/crop parameters, DNDC simulated harvestable grain C-biomass of both crops very close to observed values (only -2.81% to -6.17% less). DNDC also predicted effects of nutrient management practices on grain C-biomass of rice/wheat under CT/RT using d-index (0.76 to 0.96) and the calculated root mean squared error (RMSE of 165.36 to 494.18 kg C ha-1). DNDC simulated SOC trends for rice-wheat using measured values of several statistical indices. Regression analysis between modeled and observed SOC dynamics was significant with R2 ranging from 0.35 to 0.46 (p < 0.01), and intercept ranging from 0.30 to 1.34 (p < 0.65). DNDC demonstrated that combined inorganic and organic fertilization may result in higher C-biomass and more SOC sequestration in rice-wheat systems.

Recently, the difficulties in recycling and environmental pollution caused by metal-based electrode materials have limited the further development of batteries. Therefore, biomass carbon materials, with their environmental friendliness and stable performance, are the key to solving this problem. Many advances have been achieved by researchers for the application of biomass porous carbon materials in batteries. Nevertheless, the same biomass carbon materials in batteries face problems such as low utilization, low yield, and a cumbersome preparation process. This paper thus aims to summarize the recent progress of biomass carbon materials in the field of batteries and provide a detailed description of the battery performance of biomass carbon materials from three perspectives: synthesis, structure and application of carbon materials. We believe that biomass carbon composites are in line with future development and have a broad application prospect. Finally, we will give our in-depth prospect on developing biomass carbon materials.

The microorganisms able of accumulating lipids in high percentages, known as oleaginous microorganisms, have been widely studied as an alternative for producing oleochemicals and biofuels. Microbial lipid, so called Single Cell Oil (SCO), production depends on several growth parameters, including the nature of the carbon substrate, which must be efficiently taken up and converted into storage lipid. Οn the other hand, substrates considered for large scale applications must be abundant and of low acquisition cost. Among others, lignocellulosic biomass is a promising renewable substrate containing high percentages of assimilable sugars (hexoses and pentoses). However, it is also highly recalcitrant and therefore it requires specific pretreatments in order to release its assimilable components. The main drawback of lignocellulose pretreatment is the generation of several by-products that can inhibit the microbial metabolism. In this review, we discuss the main aspects related to the cultivation of oleaginous microorganisms using lignocellulosic biomass as substrate, hoping to contribute to the development of a sustainable process for SCO production in the near future.

Carbohydrate composition of lignocellulosic biomass is one of the main factors for production of biofuel from the plant biomass. Various methods like Thermogravimetric analysis (TGA), near infrared spectroscopy (NIR) often used in determination of polysaccharide component of the plant biomass. However, used of such tools is based on the prediction and very costly. This paper discussed about the determination of carbohydrate composition (cellulose, hemicellulose and lignin) using the automatic fibre estimation system. The protocol was developed for the estimation of cellulose, hemicellulose and lignin component of lignocellulosic biomass. This protocol explains a simple method to estimate the polysaccharide component of lignocellulosic biomass. This protocol can be used not only lignocellulosic biomass but also for other hardwood biomass. The advantages and techniques, procedures are presented below.

Antioxidant activity is an essential feature required for oxygen-sensitive merchandise and goods, such as food and corresponding packaging as well as materials used in cosmetics and biomedicine. For example, vanillin, one of the most prominent antioxidants, is fabricated from lignin, the second most abundant natural polymer in the world. Antioxidant potential is primarily related to the termination of oxidation propagation reactions through hydrogen transfer. The application of technical lignin as a natural antioxidant has not yet been implemented in the industrial sector, mainly due to the complex heterogeneous structure and polydispersity of lignin. Thus, current research focuses on various isolation and purification strategies to improve the compatibility of lignin material with substrates and enhancing its stabilizing effect. This contribution presents antioxidant capacity studies of various lignins depending on purification degree of the raw material. In detail, the antioxidant potential of lignin-based compounds is studied using the DPPH (2,2-diphenyl-1-picrylhydrazyl) assay. The purification procedure was monitored by thin layer chromatography (TLC) and showed that double-fold selective extraction is the most efficient purification procedure (confirmed by UV-Vis, FTIR, HSQC and 31P NMR spectroscopy, SEC and XRD analysis). Results are discussed regarding the dependency of antioxidant activity on lignin structure and biomass source. Thus, lignins obtained from industrial black liquor are compared with beech wood samples. In addition, the influence of lignin isolation (kraft versus organosolv) is discussed. Values of the antioxidant activity (DPPH inhibition) of kraft lignin fractions were 62-68% while beech and spruce/pine-mixed lignins showed values between 26, 64 and 42%, respectively. TPC values of the different isolated kraft lignin fractions varied between 26-35%, while beech, spruce/pine lignins were 34, 30 and 34%, respectively. Storage decreased the TPC values and increased the DPPH inhibition.

Malaysia generates significant quantities of Oil Palm Wastes (OPW) which can be potentially valorised into sustainable bioenergy as envisaged by the National Biomass Strategy (NBS-2020). Despite significant investments, policy directives and government support, the valorisation of OPW into bioenergy has remained low exacerbating waste management challenges. Therefore, the strategies and impediments to the rapid bioenergy development and bioelectricity generation from OPW require practical assessment. Therefore, this paper examines the level of development and diffusion of the biomass innovation system in Malaysia based on the Functions of Innovations Systems (FIS) approach developed by Dutch and Swedish researchers. Furthermore, the key factors hindering biomass energy technologies implementation in Malaysia and potential solutions were identified, highlighted and examined. Based on the FIS analysis the functions; entrepreneurial activities, knowledge development, and resources mobilization functions are well established in the Malaysian biomass innovation system (BIS). However, the functions of guidance of search; creation of legitimacy; knowledge diffusion and market formation are underdeveloped resulting in the low penetration of bioenergy in Malaysia. Other factors include; fossil fuel subsidies, numerous or conflicting energy policies and weak collaboration between academia and the industry. The outlined challenges can be addressed by revising fuel subsidies, Feed-in tariffs, RETs implementation, roles of supervisory agencies, and bureaucratic procedures for access to funds for research and development of bioenergy in Malaysia.

Eryngium foetidum L., a biennial herb with diverse applications in food and traditional medicine, holds economic and pharmacological significance. Given its growing commercial interest, implementing biotechnological approaches like plant tissue culture is vital for sustainable propagation and metabolite production. In this study, we investigated the in vitro photoautotrophic potential of E. foetidum, examining growth, chlorophyll a fluorescence, photosynthetic pigments, and anatomical features under different sucrose concentrations and gas exchange rates. Acclimatization and survival rates of plants after ex vitro transfer were also assessed. E. foetidum exhibited robust growth in both photoautotrophic and photomixotrophic conditions, with natural ventilation significantly enhancing plant development. Chlorophyll a fluorescence and photosynthetic performance were influenced by sucrose and gas exchange, highlighting the importance of these factors in plant micropropagation. Moreover, the species demonstrated remarkable plasticity during acclimatization, with high survival rates and rapid inflorescence emission. The research provides valuable insights into optimizing in vitro cultivation conditions for E. foetidum, emphasizing the potential for large-scale clonal propagation and exploring secondary metabolites. The observed phenotypic plasticity underscores the adaptability of the species to diverse environments. These biotechnological strategies open avenues for future studies, including the application of elicitors for enhanced secondary metabolite production.

Lignocellulosic biomass has demonstrated great potential as feedstock for pellet production, notwithstanding the fact that the industrial production of pellets is faced with some economic challenges. This study presents a technoeconomic analysis of six case scenarios to develop a process model for pellet production from sawdust and oat straw that employs torrefaction and steam explosion pretreatment prior to pelletization. SuperPro Designer was used to carry out this evaluation. The pellet plants were designed to have a capacity of 9.09 t/h of sawdust and oat straw each. The pellet yield ranged from 59 kt– 72 kt/year. Scenarios analyzed included variations of steam explosion and torrefaction. In some scenarios materials were lost in the form of liquid and gas due to the pretreatment process. The breakdown of equipment purchase cost showed that the torrefaction reactor is the most expensive unit with about 51% of the purchase cost. Facility-dependent and feedstock costs were the major significant contributors to the pellet production cost. The profitability of pellet production as determined by the net present value (NPV), internal rate of return (IRR), and payback period and was found to be sensitive to variations in feedstock cost.

Dipteryx spp. is an important species in reforestation in the Amazon. The objective of this study is to characterize and compare the relationships between dendrometric variables in Dipteryx spp. stands in the Western Amazon by fitting linear regression equations for total height and crown diameter. Six forest stands were evaluated in three municipalities. Dendrometric variables collected included diameter at 1.3 m height (dbh), total height (ht) and crown diameter (dc). Simple and multiple linear regression equations were fitted to characterize the relationships between ht and dc. The total aboveground biomass of Dipteryx spp. trees and the carbon stock of the stands were estimated. The general equations showed higher R² values, exceeding 0.7. The general equations for estimating ht and dc were significant for all coefficients. The trees averaged 22 t/ha of aboveground biomass in the stands. There was a variation in carbon sequestration potential among stands, ranging from 5.12 to 88.91 t CO2.ha-1. Single-input equations using dbh as an independent variable are recommended for estimating dc and ht for individual Dipteryx spp. stands. Stands in the Western Amazon play a significant role in carbon sequestration and accumulation. Trees can sequester an average of 4.8 tons of CO2 per year.

Recently, the move from cost-tied to open-access data has led to the mushrooming of research in pursuit of algorithms for estimating aboveground grass biomass (AGGB). Nevertheless, a comprehensive synthesis or direction on the milestones archived or an overview of how these models perform is lacking. This study synthesises the research work from decades of experiments in order to point researchers in the direction of what was done, the challenges faced, as well as how the models perform. A pool of findings from 108 remote sensing-based AGGB studies published from 1972 to 2020 show that about 62% of the remote sensing-based algorithms were tested in the Steppe grasslands, mostly in the temperate climate zone. An uneven annual publication yield was observed with approximately 36% of the research output from Asia whereas countries in the global south yielded few publications (&lt;10%). Optical sensors, particularly MODIS, remain a major source of satellite data for AGGB studies, whilst studies in the global south rarely use active sensors such as Sentinel-1. Optical data tend to produce poor regression accuracies that are highly inconsistent across the studies compared to Radar. Vegetation indices, particularly the Normalised Difference Vegetation Index (NDVI), remain a major predictor variable. Predictor variables such as Sward height, Red edge position and Backscatter coefficients produced slightly consistent accuracies. Deciding on the optimal algorithm for estimating AGGB is daunting due to the lack of overlap in the grassland type, location, sensor types, and predictor variables, signalling the need for further studies around the transferability of remote sensing-based AGGB models.

COPD is a chronic inflammatory disease characterized by progressive airflow obstruction. Tobacco smoking is the main cause of COPD (COPD-TS), but chronic exposure to biomass smoke (COPD-BS), mainly wood smoke, is the second risk factor; both are considered to cause different phenotypes of COPD. COPD-BS is more eosinophilic than COPD-TS. The objective of the present study was to evaluate the serum level of interleukins involved in eosinophil maturation, recruitment, and survival, and their association with small airway obstruction, measuring cytokines by multiplex test (Bio-Plex) and evaluating the central airway resistance with impulse oscillometry (IOS), comparatively in patients with COPD due to biomass and smoking. The results showed that IL-1ra, IL-2, IL-4, IL-8, IL-9, IL-13, IL-17, and eotaxin were increased in COPD-BS related to COPD-TS. Resistance parameters showed that R5, X5, AX (area reactance), and R5-R20 were significantly higher in COPD-BS than in the COPD-TS group (p < 0.05). R20 was not different between the groups. These data suggest that the cytokines involved in the effect of eosinophils on airway inflammation in COPD-BS were increased compared with COPD-TS, which appears to be related to a predominance of peripheral airway obstruction in patients with COPD-BS more than in COPD-TS

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

Many corporations and governments aspire to become Net Zero Carbon Dioxide by 2030-2050. Achieving this goal requires understanding where energy is produced and consumed, the magnitude of CO₂ generation, and the Carbon Cycle. Many prior proposed solutions focus on reducing future CO₂ emissions from continued use of fossil fuels. Examination of these technologies exposes their limitations and shows that none offer a complete solution. For example, bioethanol is shown to be both carbon and energy inefficient. Direct Air Capture technologies are needed to reduce CO₂ already in the air. The most natural form of Direct Air Capture involves letting nature do the work of creating biomass via photosynthesis. However, it is necessary to break the Carbon Cycle by permanently sequestering that biomass carbon in “landfills” modified to discourage decomposition to CO₂ and methane. Tree leaves and biomass grown on-purpose, such as high yield switchgrass, are proposed as good biomass sources for this purpose. Left unsequestered, leaves decompose with a short Carbon Cycle time constant releasing CO₂ back to the atmosphere. While in any given year, leaves represent a small fraction of a tree’s above ground biomass, leaves can represent a substantial fraction of the total biomass generated by a tree when integrated over a tree’s lifetime. Understanding the chemistry of the distinct phases landfills undergo is the key to minimizing or eliminating decomposition. First, the compact cross-linked structure of cellulose and keeping water out will make it difficult for initial depolymerization to release sugars. Air ingress should be minimized to minimize Phase I aerobic decomposition. pH manipulation can discourage acid formation during Phase II. Lignocellulose is low in nutrients needed for anaerobic decomposition. Inhibitors can be added if needed. The goal is to move quickly to the dormant phase where decomposition stops. The cost for Carbon Capture and Storage (CCS) for growing and sequestering high yield switchgrass is estimated to be lower than CCS for steam reforming of methane hydrogen plants (SRM) and supercritical or combined cycle coal power plants. Thus, sequestration of biomass is a natural, carbon efficient, and low-cost method of Direct Capture. Biomass sequestration can provide CO₂ removal on giga tonnes per year scale and can be implemented in the needed timeframe (2030-2050).

Tree biomass and diversity relationship in mixed forest impacts on forest ecosystem services provisions. Tree biomass yield is driven by several aspects such as species identity, site condition, stand density, tree age as well as tree diversity expressed as species mingling and structural diversity. By comparing diverse degrees of tree mixture in natural forests we can insight on the ecosystem services provision level and dynamic. Two monitoring sites in the Castilian Northern Plateau (Spain) have been analyzed to disentangle the relationships between biodiversity levels and tree biomass yield. Two permanent one ha squared plots were established at Llano de San Marugan and Valdepoza. In each plot all individual trees were measured (diameter and height), georeferenced and its species identity defined. Tree species in the two sites were Pinus sylvestris, Pinus nigra, Pinus pinea, Quercus pyrenaica, Quercus ilex, Quercus faginea and Juniperus thurifera. From these datasets ten diversity indices that fall in three categories (species richness indices, species compositional/mingling indices and vertical structural indices) were used as predictor variables to fit several candidate models. By merging the trees by site (without considering the species identity) selected models include individual tree basal area as explanatory variable combining by addition or interaction with diversity indices. When species are analyzed independently structural diversity impacts on biomass yield in combination (additive or multiplicative) with tree size is negative Pinus nigra and positive for the other species.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.

Macrophytes and seagrasses play a crucial role with a variety of the functions in the marine ecosystem and respond synchronized-promptly to the changing climate, followed by ecological status. Monitoring of the seagrasses was one of the paramount topics at the marine environment. One of the fast monitoring techniques is the vegetation acoustics with the advantages compared to the other remote sensing techniques. The acoustic method alone is ambitious to sea-truth identities of the backscatterers at the sea. Therefore, a package of computer programs was developed to identify, estimate leaf biometrics (leaf length and biomass) of one of the common seagrasses, Posidonia oceanica. Some troubleshooting in the acoustical data were fixed and then solved to reach the estimates regarding to the matters encountered for the vegetation as well as fisheries and plankton acoustics. One of the trouble was the “Lost” bottom which occurred during the data collection and post-processing due to occurrence of the acoustical noises, reverberations, interferences and intense scatterers suchlike fish schools. Another problem to remove was the occurrence as studying the near-bottom echoes belonging to submerged vegetations such as seagrasses, followed by spurious echoes. Last one was recognition of the seagrass to estimate leaf length and biomass calibrating the sheaths/vertical rhizome of the seagrass and establishing relationships between acoustical units and biometrics, respectively. As a consequence, an autonomous package of the code written in language MatLab was developed to perform all processes, and the name of the package was abbreviated as POSIBIOM, POSIdonia BIOMass. This study presented the algorithms, methodology, acoustics-biometrics relation, and mapping of the biometrics for the first time, and discussed advantages and disadvantages of the package compared to the software purposed for the bottom types, habitat and vegetation acoustic. The future studies were recommended to improve the package.

The isolation and potential applications of chitosan from the fungal source is an alternative to crustacean chitosan and synthetic polymers. The strains of Basidiomycota (Heterobasidion annosum, Phanerochaete chrysosporium, Pleurotus ostreatus, Trametes versicolor, Lentinus lepideus) with different environmental distribution, ecological importance, and industrial application were studied for mycelial biomass production in submerged (SF) and solid state fermentation (SSF). Further, the chitosan from fungal cells was extracted and characterized by elemental analyses (nitrogen) and FTIR spectroscopy. The fruiting bodies of Pleurotus ostreatus, Agaricus bisporus and Ganoderma ap-planatum were chosen as a reference material of chitosan content in basidiocarps. Stationary SF gave the lowest biomass yield in comparison with shaken SF and SSF. The role of aeration and agitation in biomass production was clearly observed in shaken SF with the highest yield achieved by P. chrysosporium. The highest biomass yield in SSF produced P. ostreatus and T. versi-color. The content of chitosan within fungal species varied depending on the method of cultiva-tion. The highest chitosan yield among the cultivated strains was obtained from mycelium of P. chrysosporium and T. versicolor in SF. The highest chitosan yield in fungal fruiting bodies demon-strated commercially cultivated mushroom A. bisporus. The extracted chitosan is proposed as functional biopolymer additive for ecological materials to substitute the synthetic wet and dry strength agents in packaging materials.

Confronted by declining fossil fuels and the need to mitigate the effects of climate change, organic-based biomass is increasingly used to produce renewable energy, and this is receiving significant attention. Biohydrogen production by dark fermentation is a promising alternative to the conventional method since it is non-polluting and energy-saving. In this review paper, a bibliometric analysis was performed to understand the current status of biohydrogen production by dark fermentation. A total of 122 articles were analyzed from PubMed between 2013 and 2022 to understand the current trend in the dark fermentative production of hydrogen. The findings revealed that there had been increasing research in the domain of dark fermentation over the past decade, signifying an increased interest in biohydrogen production through dark fermentation. A significant increase in studies geared towards optimizing the processes, including pretreatment and designing of bioreactors and choosing the right types of biomass, was herein potentially identified. This study concludes that a new perspective on biohydrogen production is needed, particularly focusing on the optimization of the dark fermentative process

Microalgae biomass is a budding raw material for the origination of food, fuel, and other value-added products. However, bulk production of microalgal biomass at commercial level is a herculean task for the current microalgal mass production technologies due to the undesirable contaminations by biological pollutants. These contaminants hamstring the production of microalgae biomass by debilitating the growth of cultures, crumble the quality of biomass and sometimes may crash the whole culture. The best utilization of the microalgae biomass at industrial level could be attained by avoiding various possible biological contaminations in mass cultivation system, understanding the contamination mechanisms, and the complex interactions of algae with other microorganisms. This review explores the various types of biological pollutants, their possible mode of infection along with mechanisms, different controlling methods to maintain desired microalgae culture.

Microalgal harvesting is one of the most challenging processes in the development of algal research and development. Several methods, such as centrifugation, flocculation, and filtration, are available at the laboratory scale. However, the requirement of expensive pieces of equipment and the possibility of biomass contamination are recurring gaps that hinder the development of microalgae I+D in different parts of the world. Recently, the electroflotation has been proved as a suitable method for the harvesting of different species of microalgae and cyanobacteria. To this day, there are no companies that sell laboratory-scale electroflotation equipment; this is mainly due to the gap in the knowledge on which factors (time, mixing rate, number of electrodes, and others) will affect the efficiency of concentration without reducing the biomass quality. This paper aims to build an innovative low-cost electroflotation system under 300 USD with cheap and resistant materials. To achieve our goal, we test the interaction of three variables (time, mixing rate, and amount of electrodes) were evaluated. Results showed that an efficiency closer to 100% could be achieved under 20 minutes using >10 electrodes and 150 rpm. We hope this innovative approach can be used by different researchers to improve our knowledge of the concentration and harvesting of algae and cyanobacteria.

The removal of metal ions by biosorption on inexpensive materials is still a challenge for environmental engineering research. In this study, marine green algae biomass (Ulva lactuca sp.) and the biochars obtained from this biomass, at 320 C (BC-320) and 550 C (BC-550), were used as biosorbents for the removal of Cu(II) ions from aqueous solution. In addition to comparing the biosorption capacities, the determination of the thermodynamic parameters allows the choice of the most suitable material for the biosorption processes. The experimental results, obtained for Cu(II) ions biosorption on each biosorbent (algae biomass (AB), BC-320 and BC-550), at three different temperatures (10, 30 and 50 C) were analyzed using Langmuir and Freundlich isotherm models, while pseudo-first order, pseudo-second order and intra-particle diffusions models were used to model the kinetic data. The biosorption of Cu(II) ions is best described by the Langmuir model and the pseudo-second kinetic model, regardless of the type of biosorbent. The maximum biosorption capacity (qmax, mg/g) depends on the temperature, but also on the type of biosorbent, and follow the order: BC-320 &lt; AB &lt; BC-550. Using the experimental isotherms, the thermodynamic parameters (G0, H0 and S0) for the biosorption of Cu(II) ions on each biosorbent were calculated. The analysis of the obtained values constitutes the main arguments in choosing BC-550 as the most effective biosorbent for the removal of Cu(II) ions from aqueous media.

Alkali-containing submicron particles were measured continuously during three months, including late winter and spring seasons in Gothenburg, Sweden. The overall aims were to characterize the ambient concentrations of combustion-related aerosol particles and to address the importance of local emissions and long-range transport for the atmospheric concentrations in the urban background environment. K and Na concentrations in the PM1 size range were measured by an alkali aerosol mass spectrometer (Alkali-AMS) and a cluster analysis was conducted. Local meteorological conditions and some other data sets were obtained, and back trajectory analyses and chemical transport model (CTM) simulations were included for the evaluation. The Alkali-AMS cluster analysis indicated three major clusters: 1) biomass burning origin, 2) mixture of other combustion sources, and 3) marine origin. Low temperatures and low wind speed conditions correlated with high concentrations of K-containing particles, mainly due to regional emissions from residential biomass combustion; transport of air masses from continental Europe also contribute to cluster 1. The CTM results indicate that open biomass burning in the eastern parts of Europe may have contributed substantially to high PM2.5 concentrations (and to cluster 1) during an episode in late March. According to the CTM results the mixed cluster (2) is likely to include particles emitted from different source types and no single geographical source region seems to dominate for this cluster. The back trajectory analysis and meteorological conditions indicated that the marine origin cluster was correlated with westerly winds and high wind speed; this cluster had high concentrations of Na-containing particles, as expected for sea salt particles.

Understory plants are important components of forest ecosystem productivity and diversity. Compared to biomass models of overstory canopy trees, few are available for understory saplings and shrubs and therefore their roles in estimation of forest carbon pools are often ignored. In this study, we harvested 24 understory species including 4 saplings, 9 tree-like shrubs and 11 typical shrubs in coniferous and broadleaved mixed forest in northeastern China and developed the best fit allometric equations of above- and below-ground and total biomass by species-specific or multispecies using morphological measurements of basal diameter, height and crown area as independent variables. The result showed that single basal diameter, height or crown area had good explanatory power for both species-specific and multispecies (p<0.001). The best-fit models included only basal diameter in sapling and tree-like shrubs, and combinations of crown area, height, and basal diameter in typical shrubs. The logarithmic model was most desired among the 4 model forms of linear, quadratic, multiple linear and logarithmic, for species-specific and multispecies. The models we developed should help the estimation of forest ecosystem carbon stocks, especially for belowground component, and provide tools for quantification of individual species biomass of understory plants.

Introduction: Biofuels, biohydrogen and bioethanol have properties that stand out from other fossil fuels, are colorless, odorless, and insipid, therefore, they are free of contaminants. Its production can be generated from the biomass of the aquatic plant Eichhornia crassipes, since this alternative is timely and viable due to its high energy composition. This plant is a problem in wetlands, rivers and other hydrosystems, due to its abundance and dominance over other species of aquatic plants, and which in effect causes an ecological imbalance. Objective: To evaluate the production of biohydrogen and bioethanol from the biomass of the E. crassipes plant. Materials and methods: Lignocellulosic material was used, realizing different physical, chemical and biological processes such as: reduction of size, lignin removal, acid hydrolysis, fermentation and distillation. a laboratory scale production system was designed and built where two bioreactors were used in the process. Results and discussion: the production of bioethanol and biohydrogen showed a production index of more than 40 mg of bioethanol per gram of bio-mass of E. crassipes and in relation to biohydrogen, 65 mmol / L was obtained. Conclusion: With the biomass of E. crassipes it is possible to obtain a high index of bio-fuel production, since it is possible to take advantage of its physical characteristics and its high proliferation in hydrosystems, in this way it constitutes an optimal alternative to produce biohydrogen and bioethanol at a high scale.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

The development of modern genomic tools has sped up the breeding program of food crops. More recently, genomic resources are being developed for tropical forages and will be key resources for developing climate resilient high yielding forage varieties. In this study, we present a genome-wide association study for biomass yield and feed quality traits in buffel grass (Cenchrus ciliaris L. aka Pennisetum ciliare L.,). Genome-wide markers generated using the DArTSeq platform and mapped onto the reference genome of Setaria italica were used for the genome-wide association study. The results revealed several markers associated with biomass yield and feed quality traits. A total of 78 marker trait associations were identified with R2 values ranging from 0.138 to 0.236. The marker trait associations were distributed across different chromosomes. Of these associations, the most marker trait associations (23) were observed on Chr9, followed by Chr5 with 12. The fewest number of marker trait associations were observed on Chr4 with 2. In terms of traits, 17 markers were associated with biomass yield, 24 with crude protein, 26 with TDN, 14 with ADF, 10 with NDF and six with DMI. Twenty of the identified markers were associated with at least two traits. The identified marker trait associations provide a useful genomic resource for future improvement and breeding of buffel grass.

The presence of metal ions, in high concentrations, in the effluents results from industrial metal coating is a well-known fact. Most of time, such metal ions, once they reach the environment, contribute significantly to its degradation. Therefore, it is essential that before such effluents are discharged into the environment, the concentration of metal ions is reduced (as much as possible), to minimize the negative impact on the quality of ecosystems. Among all methods that can be used to reduce the concentration of metal ions, sorption is one of the most viable options, due to its high efficiency and low cost. Moreover, due to the fact that many of the industrial wastes have sorbent properties, this method is in accordance with the principles of circular economy. Based on these considerations, in this study, mustard waste biomass (resulting after oil extraction) was functionalized with an industrial polymeric thiocarbamate (METALSORB), and used as an sorbent to removal Cu(II), Zn(II) and Co(II) ions from aqueous media. The best conditions for the functionalization of mustard waste biomass were found to be: mixing ratio biomass : METASORB = 1g : 1.0 mL and temperature of 30 C. The experimental sorption capacities of functionalized sorbent (MET-MWB) were 0.42 mmol/g for Cu(II), 0.29 mmol/g for Zn(II) and 0.47 mmol/g for Co(II), and were obtained in the following conditions: pH of 5.0, 5.0 g sorbent/L and temperature of 21 C. Modeling of isotherms and kinetic curves, but also the analysis of the results obtained from desorption processes, demonstrates the usefulness of this sorbent in the treatment of effluents contaminated with metal ions. In addition, tests on real wastewater samples highlight the potential of MET-MWB for large-scale applications.

An upsurge in global population over the years and rapid urbanization have accelerated huge dependence on petroleum-derived fuels and consequent environment concerns owing to green-house gas emissions in the atmosphere. An integrated biorefinery uses lignocellulosic feedstock as raw material for the production of renewable biofuels, and other fine chemicals. The sustain-able bio-economy and the biorefinery industry would benefit greatly from the effective use of lignocellulosic biomass obtained from agricultural feedstocks to replace petrochemical products. Lignin, cellulose, hemicellulose, and other extractives, which are essential components of ligno-cellulosic biomass, must be separated or upgraded into useful forms in order to fully realize the potential of biorefinery. The development of low-cost and green pretreatment technologies with effective biomass deconstruction potential is imperative for an efficient bioprocess. The abun-dance of microorganisms along with their continuous production of various degradative en-zymes makes them suited for the environmentally friendly bioconversion of agro-industrial wastes into viable bioproducts. The present review highlights the concept of biorefinery, ligno-cellulosic biomass and its valorization by green pretreatment strategies into biofuels and other biochemicals. The major barriers and challenges in bioconversion technologies, environmental sustainability of the bioproducts and promising solutions to alleviate those bottlenecks are also summarized.

Tree pruning is a management tool in agroforestry systems for reducing shade, enhancing nutrient cycling or providing fodder. However, little information is available on the effect of pruning management on plant growth, non-structural carbohydrate (NSC) levels in the roots and N2 fixation of Sesbania sesban. A glasshouse experiment was conducted to assess the effect of pruning frequency on biomass production, NSC levels and N2 fixation of Sesbania sesban. Treatments included pruning at (i) 3 months only, (ii) 3 and 6 months, and (iii) 3, 6 and 9 months, with each pruning removing shoot biomass above 50% of the initial height. Increased pruning frequency decreased above- and belowground dry matter (DM), and root NSC levels. The decrease in aboveground DM correlated with reduced levels of starch, sugar and total non-structural carbohydrates. Pruning more frequently significantly decreased nodulation, the percentage N derived from the atmosphere and N2 fixed. It could be concluded that more frequent prunings decreases biomass and NSC levels which could reduce the regeneration capacity of trees since they rely on NSCs to regrow. The suppressive effects of increased pruning frequency on N2 fixation could decrease the desirable benefits of legume trees on soil N fertility improvement.

PM_0.1 (particles diameter ≤ 0.1 µm), nanoparticles (NPs), and ultrafine particles (UFPs), were interchangeably used in the scientific communities. PM_0.1 originated from both natural and human sources. However, investigations of PM_0.1 and its effects on the environment, visibility, and human health risk to understand the levels of air pollution, sources, and impacts in South East Asia (SEA) countries continue to be lacking. The concentration of PM_0.1 in most SEA countries are much worse than those in western countries environment. A further motivation of this reviewed article is to provide a critical synthesis of the current knowledge and study of ambient PM_0.1 in SEA cities. The main influence of characteristics of PM_0.1 appears to be local sources including biomass burning and motor vehicles. Continuous monitoring of PM_0.1 in terms of both mass and number concentration should be further understood. A critical review is of great importance to facilitating air pollution control policies and predicting the behavior of PM_0.1 in SEA.

Among other species, Black Soldier Fly (Hermetia illucens, HI, Diptera, Stratiomydae) has the great potential as food and feed ingredient in the EU, particularly thanks to its preference for organic waste as growth substrate. The production of insects as livestock feed or as food ingredient requires a strict monitoring of heavy metal content in the growth substrate in order to secure its safe. This study aims to investigate the presence of toxic metals cadmium, lead, mercury, arsenic, and nickel in HI prepupae and their growth substrates based on coffee roasting by-product and microlagae Schizochytrium sp. and Isochrysis sp. Analyses were carried out via graphite furnace atomic absorption spectrophotometry for Cd, Pb, Ni, and As, and via Direct Mercury Analyzer for Hg. All metal concentrations found in growth substrates were below the legal limit of undesirable substances in animal feed (2002/32/EC). Metals concentrations in HI prepupae were in the range (mg kg-1 wet weight): Cd 0.072–0.084, Pb 0.018–0.026, Hg 0.010–0.032, As 0.036–0.047, Ni 0.18–0.76. HI prepupae accumulate Cd, Pb and Hg, but our results indicate that the risk of exposure to metals from consumption of HI prepupae is relatively low and in compliance with European Union regulations.

In order to realize rapid and nondestructive monitoring of wheat biomass in field, field experiments based on different densities, nitrogen fertilizer and variety treatments were studied. RGB images of wheat in the main growth stage were obtained by UAV, and wheat color and texture feature indices were obtained by image processing, and wheat biomass was obtained by field sampling in the same period. Then the relationship between different color and texture feature indices and wheat biomass was analyzed to select the color and texture feature index suitable for wheat biomass estimation. The results showed that there was a high correlation between image color index and wheat biomass in different stages, and most of them reached a very significant correlation level. However, the correlation between image texture feature index and wheat biomass was poor, only a few indexes reached significant or extremely significant correlation level. Based on the above results, the color indices with the highest correlation to wheat biomass or the combining indices of color and texture feature in different growth stage were used to construct estimation model of wheat biomass. The models were validated using independently measured biomass data, and the correlation between simulated and measured values reached the significant level, RMSE were smaller. This indicated that the estimated results by the models were reliable and accurate. It also showed that the estimation models of wheat biomass combined with color and texture feature indices of UAV image were better than the single color index models. The results would provide a new method for real-time monitoring of wheat field growth and biomass estimation.

Ionic liquids have been recognised as interesting solvents applicable in the efficient lignocellulosic biomass valorisation, especially in the biomass fractionation into individual polymeric components or direct hydrolysis some of biomass fractions. Considering the chemical character of ionic liquids, two different approaches, paved the way for a fractionation of biomass. The first strategy integrated a pre-treatment, hydrolysis and conversion of biomass through the employment of hydrogen-bond acidic 1-ethyl-3-methyimidazolim hydrogen sulfate ionic liquid. The second one relied on the use of a three-step fractionation process with hydrogen-bond basic 1-ethyl-3-methylimidazolium acetate to produce high purity cellulose, hemicellulose and lignin fractions. The proposed approaches were scrutinised for wheat straw and eucalyptus residues. Those different biomasses allowed understanding that enzymatic hydrolysis yields are dependent on the crystallinity of pre-treated biomass. The use of acetate based ionic liquid allowed to change crystalline cellulose I to cellulose II and consequently enhanced glucan to glucose yield to 93.14.1 mol% and 82.91.2 mol% for wheat straw and eucalyptus, respectively. Whereas for hydrogen sulfate ionic liquid, the same enzymatic hydrolysis yields were 61.6  0.2 mol% for wheat straw and only 7.90.3 mol% for eucalyptus residues. These results demonstrate the importance of either ionic liquid character or biomass type on the efficient biomass processing.

This paper presents new above-ground biomass (AGB) and biomass components equations for seventeen forest species in the temperate forests of northwestern Mexico. A data set corresponding to 1336 destructively sampled oak and pine trees was used to fit the models. Generalized method of moments was used to simultaneously fit systems of equations for biomass components and AGB, to ensure additivity. Additionally, the carbon content of each tree component was calculated by the dry combustion method, in a TOC analyser. The fitted equations accounted for on average 91, 83, 84 and 78% of the observed variance in stem wood and stem bark, branch and foliage biomass, respectively, whereas the total AGB equations explained on average 93% of the total observed variance in AGB. The inclusion of h or d²h as additional predictor in the d-only based equations systems slightly improved estimates of stem wood, stem bark and total above-ground biomass, and greatly improved the estimates produced by the branch and foliage biomass equations. The fitted equations were used to estimate AGB stocks at stand level from a database on growing stock from 429 permanent sampling plots. Three machine-learning techniques were used to model the estimated stand level AGB and carbon contents; the selected models were applied to map the AGB and carbon distributions in the study area, which yielded mean values of 129.84 Mg ha^-1 and 63.80 Mg ha^-1, respectively.

In Nigeria, the adoption of sustainable biomass for energy generation is on the rise. One crucial factor that affects the efficiency of Biomass utilization is the moisture content. This study investigates the economic impact of moisture at different stages of the wood biomass distribution chain, considering the entire chain. The methodology employed includes a comprehensive literature review, interviews, and economic calculations. By analyzing these factors, this research aims to provide valuable insights into the economics of moisture in wood biomass, contributing to the sustainable development of the Biomass energy sector in Nigeria. Based on the outcomes of this investigation, it has been discovered that the costs associated with moisture content in Nigeria amount to approximately ₦500,000,00 (Five Hundred Thousand Naira only). Utilizing wood Biomass with a moisture content of 32% weight, as opposed to 18% weight, has proven to be more costly. Transportation contributes to a significant portion of this increase, while the reduction in burning efficiency accounts for the remaining half. To further elaborate on these findings, it is crucial to understand that the transportation costs are impacted by the additional weight and volume of biomass with higher moisture content. This necessitates the use of more fuel and resources during transportation, resulting in increased expenses. Additionally, the decreased burning efficiency associated with higher moisture content poses a challenge. It leads to reduced energy output and increased fuel consumption, ultimately impacting the overall economic viability of wood biomass as an energy source. By identifying these factors, this study aims to provide insights into the economic implications of moisture content in the wood biomass distribution chain in Nigeria. These findings can serve as a basis for developing strategies to optimize the use of biomass, reduce costs, and enhance the sustainability of the energy generation process. One of the most convenient and cost-effective solutions to reduce transportation expenses and improve combustion efficiency is through planned air drying of wood biomass. Large-scale power plants typically prefer utilizing wood biomass that has undergone air drying, resulting in a moisture content ranging from 18% to 36% by weight. By implementing planned air-drying techniques, the moisture content of wood biomass can be significantly reduced, thereby decreasing transportation costs. As the biomass becomes lighter and less bulky, transportation requirements are optimized, leading to enhanced efficiency and reduced expenses. Moreover, air-dried wood biomass offers improved combustion characteristics. The reduced moisture content allows for better heat transfer during the combustion process, resulting in higher energy output and increased fuel efficiency. This not only improves the overall economics of utilizing wood biomass but also contributes to a more sustainable and environmentally friendly energy generation system. The application of planned air drying in the wood biomass distribution chain in Nigeria can serve as a practical solution to address the economic challenges associated with moisture content. By adopting this approach, stakeholders can maximize the potential of wood biomass as a renewable energy resource while minimizing costs and promoting sustainable practices.

With the swift advancement of wearable electronic devices and the electronic textile industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties even after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel materials, processing techniques, and designs for flexible energy storage devices. Among the myriad of materials investigated thus far, biomass-derived architectures have garnered significant attention due to renewability, cost-effectiveness, and abundance in earthly resources. Notably, flexible carbon membrane/ monolithic derived from biomass serve as a particularly promising option for self-supporting electrodes, align seamlessly with the requirements of next-generation electronic devices, and obviate the need for additional costs, unnecessary weight, and the high contact resistance that additive insulating adhesives may entail. This review delves into the comprehensive analysis of biomass feedstocks and methodologies employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of biomass self-supported carbon architectures and the challenges they face is provided.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

Bioenergy produced from perennial feedstocks such as woody biomass could serve as an opportunity to strengthen local and regional economies and also jointly produce various environmental services. In order to assess the potential for biomass- based bioenergy, it’s essential to characterize the interest that potential biomass suppliers have in such an endeavor. In the U.S. Great Plains region, this largely means assessing relevant perceptions of farmers and ranchers. We conducted a series of farmer and rancher oriented focus groups in North Dakota, South Dakota, Nebraska and Kansas to qualitatively explore opinions about the role that trees can play in agriculture and interest in woody biomass systems within existing Northern Great Plains (NGP) farms and ranches. Our findings suggest that farmer and ranchers generally value the role that trees, or tree-based practices like windbreaks can play in agriculture particularly on marginal farmland in terms of conservation or crop protection. Yet relative to the potential of trees as a biomass crop there is a distinct lack of knowledge and skepticism. Farmers and ranchers also noted variable degrees of risk concern and uncertainty regarding investing in tree-based systems, as well as a number of perceived external market related constraints to integrating trees within their managed systems. Most of the participants recognized that if biomass production or an increase in tree planting and management in general were to expand in the NGP region, government programs would likely be required to provide much needed technical guidance and financial incentives. As the NGP regional bioeconomy continues to emerge and expand, private and public investment relative to niche bioenergy feedstocks such as woody biomass should address the type of information needs that farmers and ranchers have relative to integrating biomass production into existing farm and ranch systems.

Stand biomass in boreal forests has attained recognition for its crucial role in carbon cycling. In this study, we examined the effect of stand age on above- and belowground biomass allocation in downy birch (Betula pubescens Ehrh.) in three drained peatland sites in Central Finland. We used allometric equations to estimate individual-tree above-ground biomass and its various components, including stem wood, stem bark, living branches, leaves, and dead branches. The above-ground biomass ranged from 10.5 t ha-1 to 276.0 t ha-1 and foliage biomass from 0.009 t ha-1 to 0.6 t ha-1. We found that stand age had a strong correlation with above-ground biomass, but foliage biomass appeared to peak at the middle-aged (50 years) stand compared to the young (10 years) or mature (80 years) stands. We observed coarse root biomass production of 45, 250, and 110 g m-2 in the 0–50 cm peat layer for young, middle-aged, and mature stands, respectively. Most coarse root biomass occurred in the top 20-cm layer (77%). These findings improve our understanding of how biomass allocation patterns – specifically those in foliar biomass– change over time, and the impact on litter inputs into the soil.

In this study, the partial least squares regression (PLSR) models were developed using no pre-processing, traditional preprocessing, multi-preprocessing 5 range, multi-preprocessing 3 range, genetic algorithm (GA), and successive projection algorithm (SPA) to assess the higher heating value (HHV) and ultimate analysis of grounded biomass for energy usage employing near-infrared (NIR) spectroscopy. A novel approach was utilized based on the assumption that using multiple pretreatment methods across different sections in the entire NIR wavenumber range would enhance the performance of the model. The performance of the model obtained from 200 biomass samples for HHV and 120 samples for ultimate analysis was compared, and the best model was selected based on the coefficient of determination of validation set, root mean square error of prediction, and the ratio of prediction to deviation values. Based on model performance results, the proposed HHV model from GA-PLSR, and the N and O models from the mul-ti-preprocessing PLSR 5 range method could be used for most applications, including research, whereas the C and H models from GA-PLSR performance is fair and applicable only for rough screening. The overall findings highlight that the multi-preprocessing 5-range method, which was attempted as a novel approach in this study to develop the PLSR model, demonstrated better accuracy for HHV, C, N, and O, improving by 4.1839%, 8.1842%, 3.7587%, and 35.9404%, respec-tively. Therefore, it can be considered a reliable and non-destructive alternative method for rap-idly assessing biomass properties for energy usage and can also be used effectively in biomass trading. However, due to the smaller number of samples used in the model development, more samples are needed to update the model for a robust application.

Biochar is an inexpensive and effective carbon sequestration technology produced by slow and fast pyrolysis of biomass feedstock at elevated temperatures in inert conditions producing large quantities of solid residue (i.e., biochar), condensable liquids (bio-oil) and hydrocarbon gases. Biochar have shown excellent adsorption capabilities. Biochar has shown excellent adsorption capabilities for short-chain PFAS and short chain PFAS. This paper suggests optimal pyrolysis reaction conditions to adsorb PFAS to maximum allowable concentrations in wastewater up to Environmental Protection Agency (EPA) is 70 ng/L. The paper highlights the operation conditions and influential reaction conditions to control the microporous structures in Biochar. The paper also aims to summarize the fundamentals of production of Biochar from biomass slow pyrolysis as well as optimal conditions for extraction of PFAS from wastewater streams and destruction of PFAS in biosolids. The scientific contributions for production of Biochar from biomass pyrolysis are highlighted. The paper also highlights the advantages of biochar over activated carbon in terms of low manufacturing costs and higher adsorption rates.

The European Bioeconomy Strategy aims to strengthen and boost biobased sectors, unlocking investments and markets while rapidly deploying local bioeconomies across Europe and improving compliance with environmental and social sustainability goals. Current biomass provision structures and infrastructure might not be able to tap the sustainable potential of forestry-, agricultural residues and biogenic waste envisaged forming the biogenic feedstock base of the Circular Bioeconomy of tomorrow. Therefore, for the present paper, we assess mobilization strategies, their current status, opportunities, and barriers for local low value and heterogenous biomass resources. Based on discussions with bioenergy supply chain experts, we cluster mobilization measures into three assessment levels; the legislative framework, market structures and technological innovation. Scientific literature research on the respective keywords is performed, the European policy landscape mapped, and the results are enriched with anecdotal evidence, especially for recent and running projects and market developments that lack in published track records. We can identify research needs on all three assessment levels. Still, technological development and legislative frameworks are providing support for heterogeneous biomass mobilization. Market creation, however, represents a bottleneck. We provide novel perspectives, how physical- and virtual bio-hubs and crediting stake- and shareholder variety could create added-value based on sustainable primary economic activities and their cascading activities.

Hydrolysate prepared from water hyacinth biomass, containing a considerable amount of solubilised carbohydrate and nutrients, was utilised as a medium for the cultivation of two strains of Chlorella sorokiniana. These strains were isolated from an oxidation pond using two different media, i.e., BG-11 and Knop's media maintained at pH-9. Different light intensities, light-dark cycles, and various concentrations of external carbon sources (monosaccharides and inorganic carbon) were used to optimise the microalgal growth. It was observed that in the presence of organic carbon (glucose), biomass productivity increased significantly (~300 mgL-1day-1) as compared to that in the presence of only inorganic carbon (~100 mgL-1day-1). For the accumulation of stress products (lipids and carbohydrates), the microalgal strains were transferred to nutrient-amended media (N-amended and P-amended). The combined effects of glucose, inorganic carbon, and a 12h:12h light-dark cycle proved to be optimum for biomass productivity. For Chlorella sp. isolated from BG-11, maximum carbohydrate content (22%) was found in the P-amended medium, whereas high lipid content (17.3%) was estimated in the N-amended medium. However, for Chlorella sp. isolated from Knop's medium, both the lipid (17%) and carbohydrate accumulation (12.3%) were found maximum in the N- amended medium. Kinetic modelling of the lipid profile revealed that kinetic coefficients obtained for strain isolated from BG-11 media were statistically significant from each other.

Biofuels and biochemicals play significant roles in the transition towards a fossil-free society. However, large-scale biorefineries are not yet cost-competitive with their fossil-fuel counterparts, and it is important to identify biorefinery concepts with high economic performance. For evaluating early-stage biorefinery concepts, one needs to consider not only the technical performance and process costs but also the economic performance of the full supply chain and the impacts on feedstock and product markets. This article presents and demonstrates a conceptual interdisciplinary framework that can constitute the basis for evaluations of the full supply-chain performance of biorefinery concepts. This framework considers the competition for biomass across sectors, assumes exogenous end-use product demand, and incorporates various geographical and technical constraints. The framework is demonstrated empirically through a case study of a sawmill-integrated biorefinery producing liquefied biomethane from forestry and forest industry residues. The case study results illustrate that acknowledging biomass market effects in the supply chain evaluation implies changes in both biomass prices and the allocation of biomass across sectors. The proposed framework should facilitate the identification of biorefinery concepts with a high economic performance which are robust to feedstock price changes caused by the increase in biomass demand.

Due to the increasing importance of mangroves in climate change mitigation projects, more accurate and cost-effective aboveground biomass (AGB) monitoring methods are required. However, field measurement of AGB may be a challenge because of its remote location and the difficulty to walk in these areas. This study is based on the Livelihoods Fund’ Oceanium project of 10,000 hectare mangrove plantations monitoring. In a first step, the possibility of replacing traditional field measurements of sample plots in a young mangrove plantation by a semiautomatic processing of UAV-based photogrammetric point clouds was assessed. In a second step, Sentinel-1 radar and Sentinel-2 optical imagery were used as auxiliary information to estimate AGB and its variance for the entire study area under a model-assisted framework. AGB was measured using UAV imagery in a total of 95 sample plots. UAV plot data was used in combination with non-parametric Support Vector Regression (SVR) models for the estimation of the study area AGB using model-assisted estimators. Purely UAV-based AGB estimates and their associated standard error (SE) were compared with model-assisted estimates using (1) Sentinel-1, (2) Sentinel-2 and (3) a combination of Sentinel-1 and Sentinel-2 data as auxiliary information. The validation of the UAV-based individual tree height and crown diameter measurements showed a root mean square error (RMSE) of 0.21 m and 0.32 m respectively. Relative efficiency of the three model-assisted scenarios ranged between 1.61 and 2.15. Although all SVR models improved the efficiency of the monitoring over UAV-based estimates, the best results were achieved when a combination of Sentinel-1 and Sentinel-2 data was used. Results indicated that the methodology used in this research can provide accurate and cost-effective estimates of AGB in mangrove young plantations.

This review analyzes the synthesis and characterization of biomass-derived carbons for adsorption of emerging contaminants from water. The study begins with the definition and different types of emerging contaminants more often founded in water streams and the different technologies available for their removal including adsorption. It also describes the biomass sources that could be used for the synthesis of biochars and activated carbons. The characterization of the adsorbents and the different approaches that could be employed for the study of the adsorption processes are also detailed. Finally, the work reviews in detail some studies of the literature focused on the adsorption of emerging contaminants on biochars and activated carbons synthesized from biomass precursors.

Halophytic plants are, by definition, well adapted to saline soils. However, even halophytes can face nutritional imbalance and accumulation of high levels of compounds such as oxalic acid (OA), and nitrate (NO₃^¯). These compounds compromise the potential nutritional health benefits associated with salt tolerant plants such as Portulaca oleracea. Thus, preventing the accumulation of non-nutritional compounds will allow plants to be grown in saline conditions as crops. To this end, two ecotypes (ET and RN) of Portulaca oleracea plants were grown under growth room conditions with two levels of salinity (0, 50 mM NaCl) and three ratios of nitrate: ammonium (0:100%; 33:66%; 25:75% NO₃^¯:NH₄⁺). The results showed that both ecotypes exposed to elevated NO₃^¯, showed severe leaf chlorosis, high levels of OA, citric acid, and malic acid, while plants of ecotype ET exposed to elevated NH₄⁺ concentrations (33% and 75%) and 50 mM NaCl displayed a marked reduction in OA content, increased total chlorophyll and carotenoid contents, crude protein content, total fatty acid (TFA) and α-Linolenic acid (ALA) thus enhancing leaf quality. This opens the potential to grow high biomass, low OA P. oleracae crops. Lastly, our experiments suggest that ecotype ET copes with saline conditions and elevated NH₄⁺ through shifts in leaf metabolites.

Treatment wetlands (TWs) are Nature-Based Solutions increasingly used worldwide for wastewater (WW) treatment able to remove mineral and organic pollutants through both physical and biochemical process. Besides the reusable effluent, the TWs produce as main output plant biomass that need to be harvested and disposed at least once a year with significant management costs and TW temporary out of service. This study aims (i) to evaluate the potential of TWs biomass for local energy production and (ii) to understand TW hydraulic conductivity (Ks) effects on the biomass biomethane yield. Specifically, it was addressed by determining the Biochemical Methane Potential of common reed (CR) (Phragmites australis) samples collected at three harvest times from the 10-years-old horizontal subsurface treatment wetland (HSTW) used as a secondary WW treatment system for the IKEA® store located in Catania (Eastern Sicily, Italy). Furthermore, the falling head test was conducted to assess the hydraulic conductivity (Ks) variation in the HSTW, in order to understand the influence on the CR biomethane production. Average methane content values were 130.57 Nm3CH4/tVS (±24.29), 212.70 Nm3CH4/tVS (±50.62) and 72.83 Nm3CH4/tVS (±23.19) in August, September, October 2022, respectively. Ks was correlated with both dry matter (R2 = 0.58) and fiber content (R2 = 0.74) and, consequently, affected the biomethane yield that increased at the Ks increases (R2 = 0.30 in August, R2 = 0.57 in September). In the framework of a circular economy, results showed the successfully possibility of integrating the bioenergy production into TWs. The research could contribute (i) to encourage plant operators to reuse biomass from TWs for local energy production and (ii) to help plant operators to understand Ks effects on the biomass biomethane yield, in order to increase the sustainability of the system and to reduce the maintenance costs.

Forest biomass is one of the most significant renewable energy sources in the Czech Republic. Recently, Czech forests have been under attack by spruce bark beetles, threatening the stability of biomass supply also for energy purposes. The goal of this paper is to uncover the impact of four different biomass development scenarios and three policies on the energy system and to evaluate the contribution of biomass to decarbonization efforts. We use the TIMES-CZ energy system optimization model to perform the analyses. We provide a crucial extension of this model by regionalizing it into NUTS3 +1 regions. Our main findings are that under the expected price of various types of biomass and their transportation cost, energy system would still exploit available biomass almost entirely throughout the period under review; subsidizing the production cost of the most expensive type of biomass for households would help utilize the full potential of biomass; and power and heat sector and industry would compete for biomass consumption against the residential sector.

Developing advanced carbon materials by utilizing biomass waste has attracted much attention. Herein, a N-doped carbon material (RSM-0.33-550) was prepared by directly pyrolyzing reed straw and melamine. The as-prepared RSM-0.33-550 possessed a N content of 6.02% and a specific surface area of 547.1 m2 g-1. As the anode for supercapacitors (SCs), in 6 M KOH, such RSM-0.33-550 exhibited a capacitance of 202.8 F g-1 at a current density of 1 A g-1. At a high current density of 20 A g-1, it still remained a capacitance of 158 F g-1. Notably, it delivered an excellent stability with capacity retention of 96.3% at 20 A g-1 after 5000 cycles. This work not only offer a new electrode material for SCs, but also gives a new insight for rationally utilizing the biomass waste for energy storage.

The demand for an efficient utilization of abundant biomasses is growing for the production of biogas and valuable bioproducts. Lignocellulose biomass is a cheap and most abundant carbon source for the production of biofuels such as bioethanol, biobutanediol, and other bio-based chemicals. Due to its complex heterogeneity, its hydrolysis gives rise to a mixture of sugars, mainly glucose; a hexose and xylose; a pentose. Glucose is the most abundant carbohydrate monomer. Most microorganisms have evolved the ability to utilize it preferably due to carbon catabolite repression regulatory mechanism at the detriment of the pentoses. Some microbes even lack the ability to utilize them. This has led to the sequential use of these sugars and accompanying reduced productivity due to inadequate utilization of the pentoses. Also, this sequential utilization of the sugars takes time and makes the overall processes economically costly. Since lignocellulose hydrolysates comprise both hexoses and pentoses, the catabolism of these sugar mixtures to biofuels will require an efficient microbial strain capable of simultaneous utilization. The use of CCR negative mutants can achieve this. CCR negative mutants simultaneously utilize pentoses and hexoses, ensuring an improved fermentation efficacy and greater productivity, thus, making the overall bioprocess economically feasible. This article reviewed several approaches employed in creating these mutant microorganisms. A brief insight on carbon catabolite repression and phosphostransferase system were made. It also highlighted the biogas production processes, factors affecting anaerobic digestion, lignocellulosic biomass structure, challenges with their use and solutions to overcoming the challenges.

Lignocellulosic biomass fractionation is typically performed using methods that are somehow harsh to the environment, such as in the case of the kraft pulping. In recent years, the development of new sustainable and environmentally friendly alternatives has grown significantly. Among the developed systems, bio-based solvents emerge as promising alternatives for biomass processing. Therefore, in the present work, the bio-based and renewable chemicals, levulinic acid (LA) and formic acid (FA), were combined to fractionate lignocellulosic waste (i.e., Maritime pine sawdust) and isolate lignin. Different parameters, such as LA/FA ratio, temperature, and extraction time, were optimized to boost the yield and purity of extracted lignin. The LA/FA ratio was found to be crucial regarding the superior lignin extraction from the waste biomass. Moreover, the increase in temperature and extraction time enhances the amount of extracted residue but compromises the lignin purity and reduces its molecular weight. The electron microscopy images revealed that biomass samples suffer significant structural and morphological changes, which further suggests the suitability of the new developed bio-fractionation process. Same was concluded by the FTIR analysis, in which no remaining lignin was detected in the cellulose-rich fraction. Overall, the novel combination of bio-sourced FA and LA has shown to be a very promising system for lignin extraction of high purity from biomass waste, thus contributing to extend the opportunities of lignin manipulation and valorisation into novel added-value biomaterials.

The kinetics of biogas production from biomass depends on several factors such as: carbon to nitrogen ratio (C/N), reactor temperature (T), and retention time (RT). The purpose of this study was to obtain a new model for predicting biogas production. Spent Mushroom Compost (SMC) was used to produce biogas in a batch type reactor. The experiments were carried out with different C/N ratios (12.1, 20, 30 and 40) and in both mesophilic (35°C) and thermophilic (55°C) temperatures. The results showed that the Maximum biogas production at 35°C, C/N=20 was equal to 41.9 mL/gVS and 55°C, C/N=30 was equal to 51.6 mL/gVS. By using experimental data, a new kinetic model was proposed to predict biogas production. Comparing the values of the results indicate that the total values of RMSE for Logistics, Gampartz and new kinetic models was 0.1906, 0.1830 and 0.1617, respectively. Therefore, the process of anaerobic digestion of biomass can be assumed to be just a chemical reaction, and the new kinetic model is an appropriate alternative to microbial growth models.

Microalgae are recognized as a third generation feedstock for biofuel production due to its rapid growth rate and lignin-free characteristic. In this study, the lipid extracted microalgae biomass residues was used as the material to produce isoprene, α-pinene and β-pinene with the engineered E. coli strain. We adopted an optimal sulfuric acid hydrolysis method to convert holocellulose into fermentable sugar efficiently (6.37 g/L) and explored a novel detoxification strategy (phosphoric acid/calcium hydroxide) to remove inhibitors notably. 55.32 % acetic acid, 99.19 % furfural and 98.22 % 5-HMF were cut down with the phosphoric acid/calcium hydroxide method, and the fermentation concentration of isoprene (223.23 mg/L), α-pinene (382.21 μg/L) and β-pinene (17.4 mg/L) using the detoxified hydrolysate as the carbon source account for approximately 86.02 %, 90.16 % and 88.32 % of those produced by the engineered E. coli strain fermented on pure glucose, respectively.

The aim of this study was to assess the influence of thermocompression conditions on lignocellulosic biomass such as sugarcane bagasse (SCB) in the production of 100% binderless bio-based materials. Five parameters were investigated: pressure applied (7-102 MPa), molding temperature (60-240°C), molding time (5-30 min), fiber/fine particle ratio (0/100-100/0) and moisture content (0-20%). These parameters affected the properties and chemical composition of the materials. The density ranged from 1198 to 1507 kg/m3, the flexural modulus from 0.9 to 6.9 GPa and the flexural strength at breaking point from 6.1 to 43.6 MPa. Water absorption (WA) and thickness swelling (TS) respectively ranged from 21% to 240% and from 9% to 208%. Higher mechanical properties were obtained using SCB with fine particles, low moisture content (4-10%), high temperature (≥ 200°C) and pressure (≥ 68 MPa), while water resistance was improved using more severe thermocompression conditions with the highest temperature (240°C) and time (30 min) or a higher moisture content (≥ 12.5%). Correlations were noted between the mechanical properties and density, while the material obtained with only fine particles had the highest mechanical properties and density. Material obtained with a 30 min molding time had the lowest WA and TS due to internal chemical reorganization followed by hemicellulose hydrolysis into water-soluble extractables.