Bangladeshi construction industry suffers a lot of safety and accidental issues than other developing countries in the world. Among many of these, accident of construction project goes far beyond and shape a horrific figure of death for every year. The aims of this study is that analysis and discussion of causes of accident at construction project in Bangladesh. A widespread statistical data collection and data analysis take place to identify the causes and design the questionnaire. The questionnaire-based survey was used to elicit the attitude of four stakeholders as workers, owners, consultants, and contractors towards passive causes of fatal accident at construction site. These study also identify 77 passive causes under 14 major groups and ranked them based on Relative Importance Index (RII). The top 5 major group of causes are (1) Management related, (2) Consultant related, (3) Technology related, (4) Labour related and (5) Contractor related. The top 5 passive causes are: (1) Unaware of safety-related issue, (2) Lack of personal protective equipment, (3) Lack of safety eliminating/ avoiding design, (4) Unfit equipment, (5) Lack of knowledge and training on equipment.

The chapter presents the current state of research concerning the development of the BE + past participle constructions from Latin to Spanish. Starting from the description in Rosemeyer (2014) and the theoretical background collated in Kailuweit & Rosemeyer (2015), it will be shown that the functional change does not follow traditional grammaticalisation paths. Several concepts that deal with cases contradicting traditional grammaticalisation theory will be discussed. ‘Exaption’ (Lass 1990, 1997) focussing on total defunctionalisation does not account for the fact that the resultative value of the BE + past participle construction, marginal in Latin, becomes central in Mediaeval Spanish. ‘Refunctionalisation’ Smith (2008) captures this aspect in a more appropriate way. However, the development of the construction could be also conceived as the opposite of what Pountain (2000) describes as ‘capitalisation’: a process of ‘decapitalisation’ by which a feature is exploited not for wider, but for more restricted purposes.

The attention to sustainable-related issues has grown fast in recent decades. The experience gained with these themes reveals the importance of considering this topic in the construction industry, which represents an important sector in the world. This work consists on conducting a multicriteria analysis of four cement powders, with the objective of calculating and analysing the environmental, human health and socio-economic effects of their production processes. The economic, technical, environmental and safety performances of the examined powders result from official, both internal and public, documents prepared by the producers. The Analytic Hierarchy Process permitted to consider several indicators (i.e. environmental, human health related and socio-economic parameters) and to conduct comprehensive and unbiased analyses which gave the best, most sustainable cement powder. As assumed in this study, the contribution of each considered parameter to the overall sustainability has a different incidence, therefore the procedure could be used to support on-going sustainability efforts under different conditions. The results also prove that it is incorrect to consider only one parameter to select the ‘best’ cement powder, but several impact categories should be considered and analysed if there is an interest for pursuing different, often conflicting interests.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

Background. Currently, most of the research in breast cancer has been carried out in conventional two-dimensional (2D) cell culture due to its practical benefits, however, the three-dimensional (3D) cell culture is becoming the model of choice in cancer research because it allows cell-cell and cell-extracellular matrix (ECM) interactions, mimicking the native microenvironment of tumors in vivo. Methods. in this work, we evaluated the effect of 3D cell organization on the expression pattern of miRNAs (by Small-RNAseq) and mRNAs (by microarrays) in the breast cancer SKBR3 cell line and analyzed the biological processes and signaling pathways regulated by the differ-entially expressed protein-coding genes (DE-mRNAs) and miRNAs (DE-microRNAs) found in the organoids. Results. We obtained well-defined cell-aggregated organoids with a grape cluster-like morphology with a size up to 9.2×105 μm3. The transcriptomic assays showed that cell growth in organoids significantly affected (all p < 0.01) the gene expression patterns of both, miRNAs and mRNAs, finding 20 upregulated and 19 downregulated DE-microRNAs, as well as 49 upregulated and 123 downregulated DE-mRNAs. In silico analysis showed that a subset of 11 upregulated DE-microRNAs target 70 downregulated DE-mRNAs. These genes are involved in 150 gene on-tology (GO) biological processes such as regulation of cell morphogenesis, regulation of cell shape, regulation of canonical Wnt signaling pathway, morphogenesis of epithelium, regulation of cy-toskeleton organization, as well as in the MAPK and AGE-RAGE signaling KEGG-pathways. In-terestingly, hsa-mir-122-5p (Fold Change (FC)=15.4), hsa-mir-369-3p (FC=11.4), and hsa-mir-10b-5p (FC=20.1) regulated up to the 81 % of the 70 downregulated DE-mRNAs. Conclu-sion, the organotypic 3D cell-organization architecture of breast cancer SKBR3 cells impacts the expression pattern of miRNAs-mRNAs network mainly through overexpression of hsa-mir-122-5p, hsa-mir-369-3p, and hsa-mir-10b-5p. All these findings suggest that the interaction between cell-cell and cell-ECM as well as the change in the culture architecture impacts gene ex-pression, and therefore, support the pertinence of migrating breast cancer research from conven-tional cultures to 3D models.

Path planning in 3D environment is a fundamental research area for robots and autonomous vehicles. Based on the principle ``the shortest path consists of tangents'', RimJump* is proposed as a tangent-based path planning method suitable for finding the shortest path (both off-ground and on-ground) in 3D space (e.g., octomap and point cloud) for mobile platform to follow. RimJump* searches the tangent graph in the form of a path tree and considers the geometrical properties of the locally shortest path. Therefore, the method can provide all of the locally shortest paths that connect the starting point and the target, including the globally shortest path. And the time cost of RimJump* is insensitive to map scale increases in comparison to methods that search the whole passable space rather than the surface of the obstacle, e.g., Dijkstra and A*. In the Results, RimJump* is compared with other methods in terms of path length and time cost.

Background: Melatonin is a potent mitochondrial, cytoprotective and antioxidant molecule with potentially strong anti-aging properties. Topical melatonin has shown to improve the clinical signs of skin aging. Melatosphere™ is a new lipid-based delivery system able to improve stability and skin penetration of melatonin when used in topical formulations. No clinical studies, using objective instrumental data, are available so far regarding the positive effect of Melatosphere™ in improving wrinkles in women with mild-to-moderate skin aging. Study Aim: We evaluate, in an open prospective, evaluator-blinded trial, the effects on skin texture of 2 months treatment with a Melatosphere™ based cream. Subjects and Methods: 15 women aged >45 years with mild to moderate facial skin aging (Glogau score ≥2) participated in the trial, after their informed consent. An ANTERA 3D computer-assisted skin analysis evaluation for the assessment of coarse and fine wrinkles of the periorbital area and melanin content was performed at baseline and after two months of treatment. An evaluator-blinded Investigator Global assessment of skin elastosis, roughness, level of dyscromia, skin dryness and presence of actinic damage was also performed at the same time points using a 4-grade score from 0 (no sign) to 3 (severe sign). Results: At baseline the mean (SD) IGA score was 8.2(1.0). After 2 months the IGA score significantly decrease to 4.2(1.4) (49% reduction) (P=0.0007). ANTERA 3D evaluations showed a significant reduction in skin coarse and fine wrinkles volume in the target area of -31% and -18%, respectively. Melanin content was reduced significantly by -17%. Conclusion: Topical melatonin carried in Melatosphere improves in the short-term signs of skin aging evaluated clinically and by ANTERA 3D device in women with mild to moderate skin aging.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

Prior to clinical trials, preclinical testing of oncology drug candidates is performed by evaluating drug candidates with in vitro and in vivo platforms. For in vivo testing, animal models are used to evaluate the toxicity and efficacy of drug candidates. However, animal models often display poor translational results as many drugs that pass preclinical testing fail when tested in humans, with oncology drugs exhibiting especially poor acceptance rates. The FDA Modernization Act 2.0 promotes alternative preclinical testing techniques, presenting the opportunity to use higher complexity in vitro models as an alternative to in vivo testing, including 3D cell culture models. 3D tissue cultures address many of the shortcomings of 2D cultures by more closely replicating the tumour microenvironment through a combination of realistic drug diffusion, paracrine signaling, cellular phenotype, and vascularization that can better mimic native human tissue. This review will discuss the common forms of 3D cell culture, including cell spheroids, organoids, organs-on-a-chip, and 3D bioprinted tissues. Their advantages and limitations will be presented, aiming to discuss the use of these 3D models to accurately represent human tissue and as an alternative to animal testing. The use of 3D culture platforms for preclinical drug development is expected to accelerate as these platforms continue to improve in complexity, reliability, and translational predictivity.

Transparent and high-hardness materials have become the object of wide interest. Most notably, it concerns technical glasses and crystals. A notable example is a sapphire – one of the most rigid materials having impressive mechanical stability and good optical properties. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on c-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for modification inscription and various etchants (Hydrofloridic acid, Sodium Hydroxide, Potassium Hydroxide and Sulphuric and Phosphoric acid mixture) comparison. We show that regular SLE etchants such as Hydrofluoric acid or Potassium Hydroxide are unsuitable materials for selective sapphire laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270°C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. Finally, a protocol for advanced sapphire structure formation and a few exemplary structures are presented.

This paper analyses and evaluate the precision and the accuracy the capability of low-cost terrestrial photogrammetry by using many digital cameras to construct a 3D model of an object. To obtain the goal, a building façade has imaged by two inexpensive digital cameras such as Canon and Pentax camera. Bundle adjustment and image processing calculated by using Agisoft PhotScan software. Several factors will be included during this study, different cameras, and control points. Many photogrammetric point clouds will be generated. Their accuracy will be compared with some natural control points which collected by the laser total station of the same building. The cloud to cloud distance will be computed for different comparison 3D models to investigate different variables. The practical field experiment showed a spatial positioning reported by the investigated technique was between 2-4cm in the 3D coordinates of a façade. This accuracy is optimistic since the captured images were processed without any control points.

Growing concerns about the greenhouse effect, global warming, and adverse climate changes primarily stemming from carbon dioxide (CO2) emissions in traditional Portland cement (OPC) used in civil engineering construction, have prompted a shift toward eco-friendly alternatives like geopolymer cement (GPC). Over the last few decades, significant advancements have been made in developing environmentally sustainable pavement construction materials such as GPC to mitigate global CO2 emissions. The success of geopolymer cement (GPC) as an eco-friendly alternative to OPC has garnered attention for its potential to lower carbon emissions and enhance durability. This is attributed to the sustainable production method of GPC, where industrial cementitious waste materials (such as fly ash (FA), metakaolin (MK), mine tailings (MT), slag, etc.) are combined with an eco-friendly alkaline activator and water through the geopolymerization process. Numerous studies on geopolymer concrete indicate that, like OPC, GPC exhibits comparable mechanical properties, including strength, fire resistance, chemical resistance, and durability. This review explores the properties and applications of GPC as a sustainable material in pavement construction, exploring key studies and advancements in geopolymer technology, particularly its suitability for pavement applications. The assessment covers the mechanical properties, long-term performance, and environmental impact of geopolymer-based pavements, providing a comprehensive overview to inform policymakers, engineers, and researchers about the viability of geopolymer-based materials as a sustainable solution for modern pavement construction.

VE is a powerful technique for analyzing a design with a focus on functionality, reducing costs, and increasing value. However, in order to proceed with the design of VE, the theoretical basis for the VE target selection process, which must be preceded in the preparation stage, is lacking, and as a result, it is difficult to verify the most effective target selection. Thus, a theoretical basis is needed. In this study, we intend to quantify the WORTH value of the COST TO WORTH technique and present an objective model of the target selection method using the derived Value Index (VI). For this purpose, cost worth (WORTHC) was calculated based on the performance data of 1,008 cases of 15 building types provided by the Domestic Public Procurement Service and the share of 83 detailed processes in 7 fields. Then, a survey was conducted targeting the ordering companies, and the final worth (WORTHF) was calculated by multiplying the derived customer value (WORTHV ) weight for each detailed work type. We calculated the Value Index (VI) by comparing COST and WORTHF for each detailed construction type of the VE project and developed a model to select construction types that exceed the VI standard value derived using the standard error of the population. Both cost experts and non-cost experts can use the developed model to specify the VE target selection criteria in order to easily select the key target, objectively sort the values that serve as the basis for calculating the value index and make it possible to more easily select the VE target selection criteria based on theoretical evidence. Also, the model can be used to obtain effective detailed design VE results.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

With the growing trend of urbanization and the growing number of people migrating to cities, the demand for the development and construction of new buildings as well as the infrastructure has risen, meaning that the construction industry must adapt to the trends. The growing demands with shorter deadlines for an industry already known for high costs and not delivering on time means that productivity must be increased without increasing the cost. The solution for this might lie in the application of the Lean philosophy to the construction industry. This paper analyses the application of the Lean philosophy in order to increase the productivity in the airport construction site. The paper highlights the potential for enhancing productivity in construction workplaces by concurrently fostering continuous improvement and sustainability through the implementation of the A3 methodology and Lean principles, resulting in waste reduction and increased value.

Big data technologies are disruptive technologies that affect every business, including those in the construction industry. The Thai government has also been affected, and attempted to use machine learning techniques with the analytics of big data technologies to predict which construction projects have a winning price over the project budget. However, this technology was never developed, and the government did not implement it because they had data obtained via a traditional data collection process. In this study, traditional data were processed to predict behavior in Thai government construction projects using a machine learning model. The data were collected from the government procurement system in 2019. There were seven input data, including project owner department, type of construction project, bidding method, project duration, project level, winning price over estimated price, and winning price over budget. A range of classification techniques, including an artificial neural network (ANN), a decision tree (DC), and K-nearest neighbor (KNN), were used in this study (ANN). According to the results, after hyperparameter tuning, ANN had the greatest prediction accuracy with 78.9 percent. This study confirms that data from the Thai government procurement system can be investigated using machine learning techniques from big data technologies.

Bamboo is the building material of the past and future. It offers numerous properties that make it versatile for various applications, including construction. Its impressive strength-to-weight ratio enables it to bear substantial loads and stresses, while its good elasticity allows efficient energy absorption. However, its mechanical properties can vary based on factors such as species, age, locations, methods, and treatment. Treating bamboo is essential to enhance its properties and durability. The literature provides various natural and chemical treatments which enhanced some of the properties but also reported a drawbacks on higher temperature, content and duration. This paper reviewed 57 articles from Scopus database, specifically focusing on article-document type publications from the years 2003 to 2023. Additional references were also incorporated to address concerns in properties, treatment and standards to provide systematic understanding. MATLAB was utilized for data text analytics. With extensive assessment on the articles, the following gaps and concerns were observed and recommends for further study and assessment such as for bamboo properties, the development of centralized guidelines and procedures for the preparation and processing; exploration of alternative materials to reinforce bamboo without compromising its ductility; development of joint connections, and testing of mechanical properties considering seismic, wind and vibration. For treatment methods, the standardization of procedures using natural, chemical or combination. Lastly, for bamboo codes and standards, assessment of existing codes and standards for testing the mechanical properties of bamboo highlighting the potential limitations and areas, uniformity, differences with all existing similar standards. By filling these gaps, it can support the reliability and robustness of bamboo as a sustainable material, fostering its promotion and adoption in construction industry.

Interprofessional learning (IPL) is essential to prepare healthcare trainees as the future public health workforce. WHIRL was an innovative IPL intervention that engaged multi-professional teams of volunteer healthcare trainees (n=20) to deliver health checks (n=464), including tailored advice and signposting, to employees in the UK construction industry (across 21 events, 16 sites, 10 organisations) as part of an ongoing research programme called Test@Work. Volunteers undertook a four-part training and support package of trainer-led education, observations of practice, self-directed learning and clinical supervision, together with peer mentoring. In a one-group post-test only design, IPL outcomes were measured using the Inventory of Reflective Vignette - Interprofessional Learning (IRV-IPL), and the psychometric properties of the IRV-IPL tool were tested. WHIRL demonstrably improved healthcare trainees’ interprofessional skills in all five areas of collaboration, coordination, cooperation, communication, and commendation. The IRV-IPL tool was found to be a valid and reliable measure of interprofessional competencies across three scenarios; before and after health promotion activities, and as a predictor of future health promotion competence. This industry-based workplace IPL programme resulted in attainment of health check competencies, and bridged the gap between research, education and clinical practice.

The question of building sustainable in a geographical locality is inexorably linked to cost. In 2011, one of the authors built a sustainable house that was (at the time) the highest certified sustainable home based on the National Association of Home Builder’s standards for sustainable construction. This Texas house has been used for residential and research purposes for the past decade. In this case study, the authors evaluate components of the construction and their effectiveness as well as unseen secondary and tertiary effects. Some of the specific components discussed are home site placement; rainwater harvesting (100% of residential requirements); aerobic septic system; grid-tied solar array power; electric car charging; geothermal heating and cooling; reclaimed wood framing; spray foam installation; selection of windows, fixtures, and appliances; on-demand electric water heaters for guest areas; generator backups; and use of local items. Electric bills and water system improvements are discussed in detail, as improvements were made as part of residential and research requirements. This case study suggests that the financial outlay is worth the extra up-front costs if residents in this geographical area and climate will occupy the residence 7 years.

Improving the efficiency of the supply process in prefabricated components is challenging and requires accounting for a variety of risks involved in the management of the suppliers. The purpose of this study is to present a method to account for the systematic trade-offs between several supplier alternatives. A novel framework is presented for the whole assessment of supplier alternatives by taking advantage of the information extracted from customized building information modeling (BIM) and a database required for assessment of impacts. A data library related to assessment criteria for supply alternatives is built to facilitate the storage and sharing of information. Analytic hierarchy process (AHP) is used to select the optimal supplier that is able to provide the most satisfaction for the determined criteria. The proposed framework was also illustrated by the implementation in a mega project. The study implication is that BIM-enabled supplier selection can indeed lead to more benefits and higher values for all stakeholders.

Construction projects are usually operating in a complex and dynamic environment in which the accumulation of many interrelated factors causes high uncertainty. Construction projects are complex and frequently involve substantial uncertainties including process complicatedness, intricate organization structure, dynamic environment, and financial strain. The study aims to categorize the influencing factors into three groups, namely construction project system, economic-market climate, and external environment. It attempts to adopt a novel analysis tool to examine the relationship between the project cost and multiple influencing factors by using Bayesian SEM. While the Bayesian SEM method has been receiving increasing attention in exploring the relationship between latent variables, construction studies still heavily rely on the covariance-based SEM approach. This study introduces several advantages of Bayesian SEM that make it more flexible and powerful than covariance-based SEM and provides the foundation of Bayesian SEM estimation and inference by illustrating this method in a project cost application.

Construction projects are usually operating in a complex and dynamic environment in which the accumulation of many interrelated factors causes high uncertainty. Construction projects are complex and frequently involve substantial uncertainties including process complicatedness, intricate organization structure, dynamic environment, and financial strain. The study aims to categorize the influencing factors into three groups, namely construction project system, economic-market climate, and external environment. It attempts to adopt a novel analysis tool to examine the relationship between the project cost and multiple influencing factors by using Bayesian SEM. While the Bayesian SEM method has been receiving increasing attention in exploring the relationship between latent variables, construction studies still heavily rely on the covariance-based SEM approach. This study introduces several advantages of Bayesian SEM that make it more flexible and powerful than covariance-based SEM and provides the foundation of Bayesian SEM estimation and inference by illustrating this method in a project cost application.

Regulators require financial institutions to estimate counterparty default risks from liquid CDS quotes for the valuation and risk management of OTC derivatives. However, the vast majority of counterparties do not have liquid CDS quotes and need proxy CDS rates. Existing methods cannot account for counterparty-specific default risks; we propose to construct proxy CDS rates by associating to illiquid counterparty liquid CDS Proxy based on Machine Learning Techniques. After testing 156 classifiers from 8 most popular classifier families, we found that some classifiers achieve highly satisfactory accuracy rates. Furthermore, we have rank-ordered the performances and investigated performance variations amongst and within the 8 classifier families. This paper is, to the best of our knowledge, the first systematic study of CDS Proxy construction by Machine Learning techniques, and the first systematic classifier comparison study based entirely on financial market data. Its findings both confirm and contrast existing classifier performance literature. Given the typically highly correlated nature of financial data, we investigated the impact of correlation on classifier performance. The techniques used in this paper should be of interest for financial institutions seeking a CDS Proxy method, and can serve for proxy construction for other financial variables. Some directions for future research are indicated.

Construction Design Management (DM) involves the coordination of design process and activity to ensure quality project design, yet it involves many challenges. This work reports on a collaborative Knowledge Transfer Project (KTP) that tackled several challenges faced by construction design management practitioners. Employing a design science research methodology (DSRM), qualitative analysis of semi-structured interviews with purposively identified design managers first uncovered real world concerns around design coordination, and designer performance monitoring. Then to address these concerns, a web-based design management prototype dashboard was developed which uses typical project data to aid the management of design coordination activity and facilitate design management task prioritization and reporting functionalities. By digitalizing selected design management processes to improve efficiency, and productivity, the visual reporting capability of the dashboard enables design production to be monitored at project and portfolio levels; trends in designer performance to be assessed and focus to be retained on technical queries (TQs) and requests for information (RFIs). By reporting on the development of this web-based Design Management prototype dashboard and illustrating how it can enhance design management productivity in construction firms, this work also provides further evidence of how employing a design science research methodology in construction can produce practical solutions that address real world construction concerns.

The introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology is based on the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In such cases, the fact that the material design methods are based on fundamental scientific principles and have been proven in laboratories and through Accelerated Pavement Testing (APT), may be of little influence. However, the general acceptance of new disruptive technologies, e.g. telecommunications and Information Technologies (IT), have been based on the considerable advantages it presented. The same principles are applicable to the general acceptance and use of NME stabilisation/enhancement of materials in the road construction industry. This article is aimed at the practical cost-effective demonstration of the general application of the use of nanos-silane modified emulsions in the construction of the highest order roads, i.e. inter-city multi-lane highways, lower order roads (including Low-Volume-Roads (LVR)) and even local accesses to farms and in villages/townships. The implementation of NME technologies is directly associated with ease of use, time and cost savings and the addressing and reduction of risks applicable to the use thereof.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

Due to the complexity, high-risk, and conservative character of construction companies, advanced digital technologies do not become widely adopted in the short term, while vendors make determined efforts to overcome this and disseminate their technologies. This paper presents the methods of an investigation addressing the extremely complex issues related to the current practices of digital technology adoption in construction. It discusses how construction companies follow a specific logical process linked to need, project objectives, characteristics of the adopting organization, and the characteristics of the new technology to be adopted. The study aims to demonstrate a novel method of data collection and analysis including data and methodological triangulation techniques including the use of NVivo and AHP to explore how companies make the decision to uptake a new technology (e.g. advanced crane, tunnel boring machine or drones) by focusing on customer and vendor activities, their interactions, contributing factors, and people involved in the process. The major original contribution of this paper is to develop an innovative methodological Cube for investigating the Construction Technology Adoption Process (CTAP) covering technology adoption, acceptance, diffusion and implementation concepts. CTAP is a framework that delineates the phases of the process that customer organizations use when deciding to adopt a new digital technology and the parallel vendor activities. The significance of these contributions is that they enable vendors to understand how to match their strategies with customer expectations in each phase of the CTAP. It also provides a benchmark for new construction companies to use the current best practice of decision making. Future research is warranted to more clearly delineate any differences with developing nations or related industries such as mining and property management.

3D cell cultures have improved the evaluation of drugs for cancer therapy, due to their high similarity to solid tumors. In melanoma, autophagy appears to show a dual role depending on the progression of the disease. p62 protein has been proposed for the evaluation of autophagic flux since its expression is an indicator of the state of autophagy. Pentoxifylline (PTX) and Norcantharidin (NCTD) are drugs that have been shown to have anticancer effects in various types of cancer. In this work, B16F1 mouse melanoma cell line was used, from which two-dimensional (2D) monolayer cultures and three-dimensional (3D) organoids were carried out using the hanging drop technique. The expression of p62 was determined by western blot and immunofluorescences. Our results indicate that pentoxifylline reduces p62 expression in both types of culture. While Norcantharidin increases its expression in 3D cultures at 24 h. Therefore, these drugs could have a potential therapeutic use for the regulation of autophagy in melanoma, depending on the state of evolution of the disease.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

This research presents the creation of a Virtual Reality experience for the Balzi Rossi museum, commemorating the centenary of Prince Albert I Grimaldi's archaeological work at the site. The project, a collaboration between the University of Genoa's 3D Lab Factory, Eurodrone, and the Balzi Rossi archaeological museum, aims to preserve and convey the site's heritage through advanced VR technology. Initially employing Unreal Engine 4, the team used photogrammetry for 3D reconstruction of the "Caviglione" and "Florestano" caves, notable for their ancient rock engravings. This first VR model, despite hardware limitations, provided an interactive exploration of the site. The subsequent development phase utilized Unreal Engine 5, incorporating Nanite technology for enhanced visual fidelity. This advancement resulted in a more detailed and immersive VR experience, presenting the Balzi Rossi cliff across different historical periods, including the Würm glaciation. Key to this phase was optimizing the VR experience for performance, focusing on stable frame rates and minimizing motion sickness, and integrating a multi-lingual interface for broader accessibility. Since November 2023, the VR setup at the Balzi Rossi Museum has been an educational and interactive feature, enabling visitors to explore the site's history virtually. This research demonstrates the potential of VR in cultural heritage preservation and education, providing a foundation for future technological improvements in the field.

When a limb suffers a fracture, rupture, or dislocation, it is traditionally immobilized with plaster. This may induce discomfort in the patient, excessive itching and sweating, which creates the growth of bacteria, leading to an unhygienic and difficulty to keep clean from treatment. Furthermore, if the plaster remains for a long period, it may cause lesions in the joints and ligaments. To overcome all these disadvantages, orthoses have emerged as important medical devices to help patients in rehabilitation, as well as for self-care of deficiencies in clinics and daily life. Traditionally, these devices are produced manually, which becomes time-consuming and error prone. From another point-of-view, it is possible to use imageology (X-ray or computed tomography) to scan the human body; a process that may help orthoses manufacturing but induces radiation to the patient. To overcome this great disadvantage, several types of 3D scanners, without any kind of radiation have emerged. This article describes the use of various types of scanners capable of digitizing the human body, to produce custom orthoses. Studies have shown that photogrammetry is the most used and most suitable 3D scanner for the acquisition of the human body in 3D. With this evolution of technology, it is possible to decrease the scanning time and it will be possible to introduce this technology in clinical environment.

Geotechnical investigation is an important site characterization process in engineering construction. Excavation pits and boreholes are popular geotechnical investigation methods for accessing subsurface soil and rock characteristics. Although they are accurate, they are limited to the discrete locations where tests are carried out. The demand for 3D representation has been increasing as an alternative for improved visualization of geotechnical investigations. This study developed a procedure for 3D modelling of geotechnical investigations using open-source software. It improves 3D visualization of geotechnical investigations and characterization of accuracy and uncertainty assessment. Presently, most geotechnical investigations do not regularly report uncertainty assessment despite its importance in risk analysis of the investigations. The procedure developed in this study was tested in a proposed site for construction of an Inland Container Depot where it depicted geotechnical soil properties with more than 80% accuracy on holdout samples. It was able to model both horizontal and vertical variations of the soil properties with quantification of uncertainty. More testing and wide applications are recommended.

Melanoma is a highly aggressive type of skin cancer produced by malignant transformation of melanocytes and it is usually associated with a poor prognosis. Clinically, melanoma has several stages associated with migration and invasion of the cells through the skin layers, rapid cell spreading and formation of tumors in multiple organs. The main problem is the emergence of resistance of melanoma to the applied methods of treatment, thus it is of primary importance to find more crucial signaling pathways that control the progression of this type of cancer and could be targeted to prevent melanoma spreading. The main life-threatening stage of melanoma is metastasis formation, and 3D cell spheroids are better suited for the study of this process. Using a combinative approach (RT-PCR, immunofluorescence, patch-clamp and calcium imaging) we showed the functional expression of mechanosensitive Piezo1 channels in SK-MEL-2 aggressive melanoma cell line. We found that chemical activation of Piezo1 by its selective agonist Yoda1 completely prevents melanoma spheroid formation, and could be considered as a novel approach for the prevention of melanoma development.

Free-edge effect is one of the factors affecting the mechanical properties of three-dimensional woven composites under tensile load. However, current research is relatively poorly understood regarding the effect of free-edge on the stiffness and strength of the material. This paper aims at examining the influence of free-edge effect on the mechanical properties of 3D woven composites under tension through experimental and simulation mathods. The three-dimensional DIC technique is used to collect the full-field strains on the specimen surface during the test, and the stress-strain differences in different regions in the width direction are analyzed, and the overlap of the curves in each region is found to be high. Experimental studies are conducted on specimens of different widths (within the range of 15-20 mm), and the results indicate that the differences in mechanical properties of 3D woven composites under tension loading in this width range are not significant. A progressive damage finite element model is developed for calculation and compared with experimental results.

The increased accessibility of drone technology and the wide use of Structure from Motion 3D scene reconstruction have transformed the approach for mapping inaccessible slopes undergoing active rockfalls. The Poggio Baldi landslide offers the possibility for many of these techniques to be deployed and integrated with the aim of defining a suitable workflow for the analysis of hazards in mountainous regions. The generation of multitemporal digital slope twins (2016 – 2019), informed a rockfall trajectory analysis that was carried out with a physical-based GIS model. We tested the rockfall scenario reconstructed and calibrated on the analysis of the rock mass characteristics and the geometrical and physical constraints given by the multi-temporal analysis of the SfM point clouds. This time-independent rockfall hazard analysis is a critical component to any subsequent holistic risk analysis on this case study, and any potential similar mountainous setting.

Beyond semantic segmentation,3D instance segmentation(a process to delineate objects of interest and also classifying the objects into a set of categories) is gaining more and more interest among researchers since numerous computer vision applications need accurate segmentation processes(autonomous driving, indoor navigation, and even virtual or augmented reality systems…) This paper gives an overview and a technical comparison of the existing deep learning architectures in handling unstructured Euclidean data for the rapidly developing 3D instance segmentation. First, the authors divide the 3D point clouds based instance segmentation techniques into two major categories which are proposal based methods and proposal free methods. Then, they also introduce and compare the most used datasets with regard to 3D instance segmentation. Furthermore, they compare and analyze these techniques performance (speed, accuracy, response to noise…). Finally, this paper provides a review of the possible future directions of deep learning for 3D sensor-based information and provides insight into the most promising areas for prospective research.

Polystyrene as a thin film on arbitrary substrates or pellets form defective graphene films or powders that can be dispersed in water and organic solvents. The materials were characterized by visible absorption, Raman and X-ray photoelectron spectroscopy, electron and atomic force microscopy and electrochemistry. Raman spectra of these materials show the presence of the expected 2D, G and D peaks at 2750, 1590 and 1350 cm^-1, respectively. The relative intensity of the G vs. the D peak is taken as a quantitative indicator of the density of defects in the G layer.

Osteoarthritis (OA) is a joint disease involving cartilage degeneration. This study aimed to compare properties of chondrocytes from less-affected (LA-Cartilage) and severely-affected (SA-Cartilage) of human OA articular cartilage. Based on Dougados classification, OA cartilage was classified into two groups; less-affected (Grade 0–1) and severely-affected (Grade 2–3). Chondrocytes from each group were cultured until passage (P) 4. Growth, migration, stem cell properties and chondrogenic properties under normal and inflammatory conditions, and the formation of in vitro 3D cartilage tissues were compared between groups. The growth and migratory properties of LA-chondrocytes and SA-chondrocytes were similar, except that the migration rate of SA-chondrocytes was significantly higher at P0 compared to LA-chondrocytes. Both LA-chondrocytes and SA-chondrocytes expressed mesenchymal stem cell markers and tri-lineage differentiation, but the expression of stem cell markers decreased significantly with increasing passage number. Exposure to inflammatory conditions induced distinct morphological changes and significant increases in expression of SOX9 at P4 and MMP3 at P1 for LA-chondrocytes. LA-chondrocytes and SA-chondrocytes able to develop into in vitro 3D constructs, but SA-chondrocytes exhibited superior cartilage-like properties. Chondrocytes from both less- and severely-affected regions are suitable to be used in clinical applications, however, chondrocytes from severely-affected regions could be a more favorable cell source.

Numerical weather prediction is an initial-value problem, for determination of the initial conditions, there are many methods and one of the most classical methods is variational methods in three dimensions, or 3D-Var. In this approach, with a defined cost function proportional to the square of the distance between the analysis and both the background and the observations, one can obtain the analysis. In the cost function, the background and the observations are reshaped to vectors; within this step, the order of the background error covariance matrix and the observational error covariance matrix becomes huge, which is not convenient to one to obtain the analysis. In this paper, according to the matrix analysis approach, we put forward some possible improvements to the dimension-reduction algorithm of 3D-Var, so that provide some references for data assimilation.

The fourth industrial revolution (4IR) can offer significant benefits to the construction sector, improving productivity, efficiency, collaborative efforts, and product quality while promoting safety and sustainability. However, research on the application of 4IR technologies in construction is scarce in developing countries. It is crucial to understand the ability of construction companies to adopt new technologies and identify factors influencing the success of technology implementation. In this study, a questionnaire-based survey was conducted with construction professionals to evaluate the level of technological development of the construction market in an emerging economy, assess the potential for innovation implementation, and identify factors that might influence technological development. Although respondents recognized the importance of digital transformation, the results showed that most innovations are in the early stages of implementation in the construction sector, particularly technologies that are essential for the consolidation of the 4IR. Understanding the factors underlying this reality can support the development of strategies to foster innovation and harness the advantages of the 4IR in the construction industry in developing countries.

Raw earth bricks made from the soil of the Chalky Champagne region (France) have been used for at least two millennia in construction, a promising heritage in the context of reducing the carbon emissions of buildings. The present experimental study aims at measuring the physical, mechanical, thermal, and hydric properties of adobes collected from a local village barn. Results show a high chalk content estimated at 71%, and a clay content, acting as binder, at 14%. Despite limited load-bearing capacity, these lightweight adobes are suitable for current single-story constructions, while their hydrothermal properties classify them as excellent moisture regulators for occupants. In association with other bio-sourced materials such as starch-beet pulp bricks, Chalky Champagne adobes yield promising insulating properties, and meet the criteria defined by current energy standards.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

Children—Dependents in Social Construction Theory—are assessed within democracies regarding their ability to self-direct their behavior concerning their associated society. In this regard, childhood represents a lack of self-direction, a life period when people require the guidance and protection of adults. The assumed necessity of adults supervising children in democracies requires substantial social resources, reducing the self-direction of those charged with overseeing children. Given that self-direction defines the optimal experience of people within democratic society, finding ways to increase the self-direction of children is an individual and a social benefit. In this regard, smartphones have improved self-direction in children. How children have become empowered to self-direct their lives with smartphone use considering Social Construction Theory—as Advantaged, Contenders, or Deviants—is the focus of a scoping review conducted on “children, empowerment, smartphones” of the following databases: OVID, JSTOR, ProQuest, PubMed, Scopus, and Web of Science. The result is that children permitted to self-direct their activities aided by smartphone technology have comparable social behavior to adults positioned as Advantaged, Contenders, or Deviants and, as such they should be encouraged to utilize smartphone technology to improve their self-direction, as doing so will augment individual and caregiver self-direction, providing increased social benefit.

The unsafe behavior of frontline workers at construction sites is the most important cause of construction accidents. This study proposed a comprehensive model of frontline workers' unsafe behaviors based on a systems perspective and used structural equation modeling (SEM) to explore the influence mechanisms between Objective Conditions (e.g., work environment, work climate, task complexity), Safety Management (e.g., safety education and training, safety reward and punishment regulations, safety inspection, safety technology disclosure, safety warning signs), Group Influence (propagation of unsafe behaviors among workers), Personal Perception (subjective judgment of operators on their safety knowledge and skills), and Unsafe Behaviors. Data from 460 frontline workers were collected through questionnaires and the correlation hypotheses were tested using SPSS 26.0 and Amos 26.0 software. The following conclusions were obtained: (1) Objective Conditions directly positively influence Safety Management, Group Influence, and Personal Perception, but indirectly negatively influence Unsafe Behavior; (2) Safety Management not only directly positively affects Personal Perception but also directly negatively affects Unsafe Behavior. However, the direct effect of Safety Management on Group Influence is not significant; (3) Group Influence has a direct positive effect on Unsafe Behavior, but the direct effect on Personal Perception is not significant; (4) The direct effect of Personal Perception on Unsafe Behavior is insignificant. These findings can be used as preliminary data to guide decision-makers or managers in construction companies to develop reasonable management plans to curb unsafe behaviors of frontline workers.

During carbonation process, the presence of water is an important parameter to accelerate this phenomenon. The carbon dioxide (CO₂) has been used as curing process production of fiber cement boards keeping the dimensional stability of cellulose fibers in cementitious matrix and promoting the CO₂ capture of environment. In addition, magnesium oxysulfate (MOS) cement has been used as another alternative binder to reduce the amount of CO₂ in the nature. The aim of this scientific paper is analysis the effect of rehydration method on the physical-mechanical properties of CO2-cured magnesium-based fiber cement boards. These boards were produced by Hatschek process simulation. The physical-mechanical performance and microstructural characteristics of MOS boards before and after carbonation were investigated by: water absorption (WA), apparent porosity (AP), and bulk density (BD); four-point bending test; X-ray diffraction (XRD); thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). According to the results, it was possible observe which the accelerated carbonation process resulted in improvements in the mechanical properties of the boards. The boards carbonated after 48 hours showed higher Modulus of Rupture values. The rehydration process of the composites before carbonation led to enhancements in the boards pre-cured for 48 and 72 hours, demonstrating that carbonation occurred more effectively after the supply of water through rehydration. The improvements in mechanical properties were associated with the formation of hydration products, which preferentially formed in the pores and voids of the fiber-cement. The presence of these carbonation products altered the physical properties of the materials, increasing the density of the boards and reducing the void volume. The decomposition of the formed carbonates was confirmed by thermogravimetric analysis, which indicated that the rehydration process favored the carbonation of the materials

To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.

Organizational climate is the ascribed psychological meanings and significance associated with the procedures, policies and practices that are recognized and rewarded in the workplace, and hence mediates the effects of environmental stimuli on individuals’ response. Safety climate is a specific organizational climate, i.e., organizational climate for safety. Previous research claimed that organizational climate provides foundation for safety climate, but without elaboration on the foundational mechanisms. This paper attempts to fill up this knowledge gap. As organizational climate is a multi-dimensional phenomenon, this paper chooses two dimensions, i.e., perceived organizational support (POS) and participative decision-making (PaDM), for illustrative purposes. Drawing on an interactive approach to forming climate perceptions, this paper introduces two interactive constructs, i.e., leader-member exchange (LMX) and team member exchange (TMX), and establishes a multiple mediation model depicting the foundational effect of organizational climate on safety climate. A random sample of Hong Kong based construction personnel is used to validate the model. The results show that both POS and PaDM are positively associated with perceived safety climate, both LMX and TMX fully mediate the effect of PaDM on safety climate, and only LMX partially mediates the effect of POS on safety climate. This study sheds light on the foundational effects of organizational climate on safety climate. POS can improve the quality of reciprocal exchange about safety matters between construction personnel and their supervisors, and hence raise construction personnel’s awareness of the priority of safety. PaDM can improve the quality of reciprocal exchange about safety matters vertically and horizontally, and hence have construction personnel aware the importance of safety. In practice, this paper suggests that project managers timely recognize and reward construction personnel’s contribution, genuinely cares about their well-being, and take their suggestions seriously in making decisions. In this way, the quality of both vertical and horizontal exchange about safety matters improves, and a sound and positive safety climate ensues.

According to circular economy principles, the recycling and reuse of waste tyre rubber is one of the most advanced and ecological waste disposal technologies. Each year about 19 million tons of tyres are produced, and this amount is increasing each year. One of the most innovative ways to recycle rubber waste is devulcanization. There are many methods of rubber devulcanization, but the most popular are grinding and chemical. In this article devulcanized rubber granules were used for the preparation of rubber samples. Two of them were obtained by the grinding method and one by chemical devulcanization. 15 different rubber samples were produced for the experimental measurements. Multilayer constructions with two solid layers of plasterboard on both sides (GKB and GKFI) and porous acoustic material of rubber sample inside were produced. Measurements were made in an impedance tube and compared with the results of TMM analysis. The same trends of resonant frequencies were determined. According to the results, the resonant frequencies depended on the thickness of the material, since transmission loss values depended on the mass of construction. According to the test results of transmission loss, constructions with 50mm thick rubber samples had on average 3dB better results than the structures with 25mm samples and 5dB better results than structures with 12 mm thick rubber samples. In addition, it was found that higher density plasterboards (GKFI) increased the overall transmission loss value of the structure by 5 dB. The same trends were determined by the TMM method. The test results showed that multi-layered constructions with devulcanized waste rubber had high transmission loss result and could be used for sound insulating structures.

Distributed Manufacturing (DM) is becoming increasingly important in operations management due to its potential to support sustainability goals, reduce risks in global supply chains, and boost local economies. However, previous analyses of the advantages and disadvantages of DM have mainly focused on operations, overlooking additional benefits across the supply chain. For example, DM can enable local sourcing, better serve end-users, and tackle reverse supply chain challenges. While economies of scale are essential for reducing costs and improving productivity, highly centralised manufacturing can increase transportation costs, vulnerability, and supply chain disruptions, particularly during pandemics or other times of restricted transportation. To address these challenges, this study introduces a Multi-attribute Decision Support System (MADSS) and assessment process that considers impacts across the supply chain and guides stakeholders, academics, and decision-makers. The MADSS handles quantitative and qualitative information, missing data, and uncertainty, and a team of experts from academia and industry in New Zealand has developed the evaluation. The MADSS was used to analyse DM and traditional construction alternatives from economic, social, environmental, and resilience perspectives in New Zealand. The research contributes to a better understanding of the impacts of DM across the entire supply chain. Also, it proposes a flexible decision-making framework to engage with stakeholders and support decision-making in other industries and regions.

This study evaluated the grain size and high organic content from drinking water treatment sludge (DWTS) in the properties of ceramics. Samples were studied using raw and oven dried DWTS at 110 °C in two granulometries (0.180 mm and 0.075 mm), with and without calcination (550 °C), as partial replacement of two soils commonly used in ceramic production. Specimens were prepared with 5, 10, and 20% DWTS and calcined at 950 °C to determine their chemical, physical, mineralogical and mechanical properties. The DWTS reduced the density and increased the absorption and shrinkage of the specimens after calcination. An increase in strength with up to 10% sludge, driven by the presence of fluxing agents, was verified. The processing method had little influence on the properties of ceramic with above 10% of sludge. In conclusion, the use of raw DWTS obtained better results with low energy usage for its reuse.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Abstract: Guanxi, a Chinese term that defines social networks of power and benefits, can be divided into inter-personal and inter-organizational relationships, and guanxi significantly influences construction innovation in China. Many studies have examined the relationship between guanxi and construction innovation at the project or organizational level. However, few of these studies explained how guanxi could affect an individual’s innovative behaviour from a double-level perspective. This paper builds on social capital theory and social exchange theory to examine guanxi’s role in motivating innovative behaviour in a China-specific construction context. It investigates the main effects of inter-personal relationships on innovative behaviour, the mediating effects of knowledge sharing, and the cross-level moderating effects of inter-organizational relationships. These elements were tested using a survey that received 178 responses from 35 different organizations. The results were analysed using Hierarchical Linear Modelling (HLM) and revealed that inter-personal relationships have positive influences on innovative behaviour, thus highlighting the partial mediating effects of knowledge sharing. In addition, the analyses showed that inter-organizational relationships augment inter-personal relationships and knowledge sharing on innovative behaviour by cross-level interaction. The research findings enhance an understanding of guanxi and innovative behaviour in China-specific construction project settings, as well as verifying the significance of guanxi in stimulating innovative behaviour.

Objectives: 1) To describe the cardiovascular health of the construction workers in Hong Kong, 2) to examine the demographic differences in cardiovascular health, and 3) to examine the association between modifiable lifestyle behaviors and cardiovascular conditions. Methods: 626 registered construction workers were included in the analysis. Blood chemistry, blood pressure, weight and height were measured. Face-to-face questionnaire interview was conducted. T-tests and One-way ANOVAs were used to compare the cardiovascular health score, cardiovascular outcomes, and lifestyle behaviors by demographic characteristics. Logistic regressions were performed to assess the cardiovascular outcomes by lifestyle behaviors. Results: Two-thirds of the construction workers failed to achieve three out of the seven “ideal” cardiovascular health indicators. The younger, more educated, and female subjects had better cardiovascular health scores than their counterparts. The ideal fish and seafood consumption was associated with 1) ideal weight status and 2) ideal cholesterol level, whereas less soft drink consumption was associated with ideal cholesterol level. Conclusions: The findings highlighted the importance of promoting cardiovascular health in the construction industry. This study provided insights for future interventions, which should include increasing fish and seafood intake, decreasing soft drink consumption, and enhancing the health literacy amongst older, less educated, and male construction workers.

As the largest energy consumer and carbon emitter, China has made substantial efforts to improve energy efficiency for decrease energy consumption, while the energy rebound effect determines its effectiveness. The embodied energy consumption of construction projects accounted for nearly one-sixth of the total economy's energy consumption in China. This paper is based on the logical relationship among capital input, technological progress, economic growth, and energy consumption, adapting an alternative estimation model to estimate the energy rebound effect for the construction industry in China for the first time. Empirical results in our paper reveal that the energy rebound effect for the construction industry in China is about 59.5% for the period of 1990–2014. The results indicate that the energy rebound effect does exist in China’s construction industry and it presented a fluctuating declining trend. This implies that half of the energy savings by technological progress is achieved. In addition, China’s government should implement proper energy pricing reforms and energy taxes to promote the sustainable development of China’s construction industry.

Background: Wilms tumor (WT) is the main renal tumor in children. SIOP-UMBRELLA Guidelines admit Nephron sparing surgery (NSS) in syndromic patients, and in small (&lt;300 ml) nonsyndromic unilateral WTs, without lymph node involvement, and with a substantial expected remnant renal function, after neoadjuvant chemotherapy. We report our prechemotherapy transperitoneal robot-assisted partial nephrectomy (RAPN) in a unilateral non-syndromic Wilms tumor. Methods: A 6-year-old-child showed an exophytic 3.6 cm diameter solid rounding mass involving the upper right renal pole at an incidental abdominal echotomography. CT-scan and abdominal MRI proved no local infiltration neither lymph node involvement was appreciated, suggesting an exophytic mass easily resectable through a NSS robotic approach, with a low risk of rupture and no subverted renal anatomy. The preoperative imaging was not suggestive for WT. A virtual 3D reconstruction of the tumor was performed. Results: the oncologic board approved a robot-assisted partial nephrectomy with the intraperitoneal approach. The histopathologic analysis displayed a WT. The patient underwent 10 vincristine-doses adjuvant chemotherapy. 28-months follow-up showed no tumor recurrence. Conclusions: Intraperitoneal RAPN can represent an opportunity for WT and needs to be assessed as a challenging possibility. This case suggests a potential role of prechemotherapy RAPN in the near future for highly selected patients.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Electric energy has become essential nowadays not only for the daily life of each of us but also for the economy of different countries. The dissemination of geographic information plays an important role in national development as it facilitates communication between managers, investors, and consumers in this sector. Since the management of electricity network data was previously done in Tunisia based on paper maps and plans, the purpose of this article is to present a case of planning based on GIS, Web, and 3D Web GIS, which would have significant positive consequences on this sector from a technical and financial sides with an improvement in customer satisfaction and the creation of an intelligent electricity network which will be a real decision-making tool. This work draws up an inventory of the network MV (Medium Voltage)/LV (Low Voltage) of the region of Medjez El Bab which routes electricity to the big centers of consumption with access to MV/LV subscribers. The analysis of the network's impedance allowed carrying out different scenarios to optimize performance and obtain more realistic routes. Many thematic maps were produced as part of this project (Slope map, Land use map, map of the MV voltage domains, map of the MV/LV transformer stations power, etc.). A three-dimensional virtual city has been developed to visualize the graphical and attribute data for the study area. A Web and 3D Web GIS applications that allows the publication of the interactive maps on the Web as well as the database information have been developed to offer users the possibility of consulting the produced products by internet. Finally, a website related to the study was developed.

A pilot study on laser 3D printing of inorganic free-form micro-optics is experimentally validated. Ultrafast laser nanolithography is employed for structuring hybrid organic-inorganic material SZ2080TM followed by high-temperature calcination post-processing. The combination allows production of 3D architectures and the heat-treatment results in converting the material to inorganic substance. The produced miniature optical elements are characterized and their optical performance demonstrated. Finally, the concept is validated for manufacturing compound optical components such as stacked lenses. This is opening for new directions and applications of laser made microoptics under harsh conditions such as high intensity radiation, temperature, acidic environment, pressure variations, which include open space, astrophotonics, and remote sensing.

During the 2008 financial crisis, central banks (such as the Fed) adopted quantitative easing (QE) policy to stimulate their economies and overcome severe economic and financial recessions. However, apart from stimulating the economy by issuing a substantial amount of currency to purchase long-term bonds and suppress interest rates, QE policy also contributed to a boom in the real estate and construction sectors. Therefore, this study employs Data Envelopment Analysis to measure the business performance (BP) of construction companies and explores the impact of QE policy on the BP of construction companies between 2004 and 2015 using ordinary least squares regression. Also, we examine the moderating role of debt ratio on the relationship. Focused on publicly listed construction companies in Taiwan, this research reveals three encouraging find-ings. Firstly, QE policy indeed enhanced the BP of Taiwanese construction companies. Secondly, the performance improvement of construction companies due to QE policy shows a time-diminishing trend, suggesting the importance of seizing the initial policy benefits of QE implementation. Lastly, construction companies with appropriate financial leverage may exhibit better BP. These findings can provide valuable insights for relevant government entities and de-cision-makers in the industry for policy and investment decisions.

The fast-paced evolution of artificial intelligence (AI), machine learning (ML), natural language processing (NLP), large language model (LLM) applications, and generative pre-trained transformer (GPT) have set the stage for improved and autonomous project scheduling models. This study demonstrates how project scheduling can be enhanced by employing building information modeling (BIM) to predict reliable schedules for each project element. The research is based on design science research (DSR) methodology and focus group discussion. The proposed system consists of six components: project analyzer, data warehouse, activity identifier and sequencing, activity magnitude and direct cost calculator, activity duration calculator, and schedule analyzer. Unlike other solutions, the proposed solution sequences activities based on an ML model rather than constraint matrices. The proposed solution thus enhances project performance through proactive planning and risk management. Integrating the autonomous project scheduling solution with the other components of an autonomous project management system would surmount schedule challenges and would result in greater cost efficiency and fewer delays.

The construction sector is considered as a major consumer of virgin materials and contributor to waste generation. Therefore, it is essential to rethink current waste management practices, for example, by applying circular economy principles to building demolition, such as deconstruction. Deconstruction involves dismantling a building with the aim of maintaining the highest possible value for its materials and maximize their recovery potential. This study aims to guide the construction sector towards deconstruction to support its efforts to transform itself toward a more sustainable industry. It focuses on a regional case study in the province of Québec (Canada) presenting five buildings to be deconstructed. First, the study presents the outcomes of our analysis of the current situation. Second, it identifies the issues and obstacles encountered and proposes avenues to improve the current process based on solutions identified in the literature and the recommendations of the manager, the contractor involved in the deconstruction process, as well as experts in the construction industry. Finally, it proposes an improved deconstruction process. Our research approach is inspired from Lean thinking and follows Action Research methodology.

The construction industry in the Kingdom of Saudi Arabia (KSA) is a significant sector in the Middle East, with annual expenditures exceeding USD 120 billion. It employs 15% of the work force and consumes more than 14% of the country’s energy resources. Despite the significant growth in the Saudi construction sector, it faces various challenges due to the rapid launch of mega projects such as NEOM and the Line project, as well as other new projects as part of the Saudi Vision 2030. Challenges might be limited to shortages of skilled labours, rising costs, construction disputes, and material shortages. This study aims to investigate the claims management procedures under traditional practice to be compared with a proposed BIM package as an alternative solution to mitigate construction disputes. The proposed BIM model improves and streamlines the claims process through automation. This study presents prospective and retrospective methods for delay analysis under an accepted program. A questionnaire survey was conducted, and out of a total of 123 practitioners, 79 replied. The findings reveal that 40% of the respondents acknowledged a growing awareness of BIM in the KSA construction industry. 47% agreed that BIM can help reduce potential disputes, and 33% strongly agreed that BIM can reduce overall project cost overruns.

This research delves into the integration of green roofs with Building Information Modeling (BIM), a pivotal advancement in sustainable urban construction. Aligning with the United Nations Sustainable Development Goals, particularly Goal 11, the study explores how this integration can address global challenges like climate change and resource depletion. Using the Dynamo Visual Programming Language within Autodesk Revit, the research develops a computational modeling approach for green roofs, focusing on their thermal and structural characteristics under varied environmental conditions. Key findings demonstrate the significant influence of substrate and drainage material combinations on green roofs’ thermal performance, highlighting the need for tailored designs based on climatic conditions. The study also emphasizes the importance of considering structural performance in both dry and saturated conditions for overall building integrity. The research identifies gaps in current practices, such as limited focus on specific green roof materials and reliance on certain software tools, suggesting the need for broader material selection and software adaptability. Future research directions include expanding material selections, exploring diverse environmental conditions, and integrating green roofs with various BIM software platforms. The study's implications extend to stakeholders in the construction industry, offering a framework for architects, urban planners, and policymakers to design and implement green roofs aligned with environmental goals. This work contributes to the field by proposing a novel approach to sustainable construction, integrating ecological design with digital technology, and setting a new benchmark in the integration of green roofs with BIM. By addressing these aspects, the research paves the way for future developments in sustainable urban construction, enhancing the efficiency, sustainability, and resilience of urban communities in line with global sustainability objectives.

The construction industry, characterized by its intricate network of stakeholders and diverse workforce, grapples with the challenge of managing information effectively. This study delves into this issue, recognizing the universal importance of safeguarding data, particularly amid rising concerns of unauthorized access and breaches. Aiming to harness the potential of blockchain technology to address these challenges, this study used a hypothetical biographical and safety data of construction workers and securely stored on a Hyperledger Fabric blockchain. Developed within the Amazon Web Services (AWS) cloud platform, this blockchain infrastructure emerged as a robust solution for enhancing data security and privacy. Anchored in the core principles of data security, the model emerges as a potent defender against the vulnerabilities of traditional data management systems. Beyond its immediate implications, this study exemplifies the marriage of blockchain technology and the construction sector, potentially reshaping workforce management, especially in high-risk projects, optimizing risk assessment, resource allocation, and safety measures to mitigate work-related injuries. Practical validation through transaction testing using Hyperledger Explorer validates the model's feasibility and operational effectiveness, serving as a blueprint for the industry's data management. Ultimately, this research not only showcases the promise of blockchain technology in addressing construction data security challenges but also underscores its practical applicability through comprehensive testing, heralding a new era of data management that harmonizes security and efficiency for stakeholders' benefit.

This research describes a detailed analysis in the enactment of a Lean Tool, the Last Planner System during pandemic period which helps in optimizing the resources for better coordination among all stakeholders in pandemic period. LPS as it is known, focusses on minimizing the factors such as uncertainties, barriers and variability to make construction projects more flexible for better project management. These include variations and deviations, supervision, delays in approvals, change resistance, subcontractor dedication which are all related to various stakeholders in the project. Following that, a Design Science Research technique is used to evaluate the effect of applying LPS in buildings. An action strategy is being used to attain this goal, and four case studies were being documented which were concerned in the implementation of LPS in the building of the Boy's Hostel, Research Scholar Quarters, Faculty Housing, and Girls' Hostel at Chennai, Tamilnadu, India. Data was gathered by observation of site activities, interviews, documentation analysis, and a questionnaire survey and grouped into various factors. While adopting the LPS tool in the research the factors affecting the implementation were found in the covid-19 pandemic period. Further these factors were anlayzed, measured, ranked and validated for adopting in projects.

Subway construction is often in a complex natural and human-machine operating environment, and that complicated setting leads to subway construction more prone to safety accidents, which can cause substantial casualties and monetary losses. Thus, it is necessary to investigate the safety risks of subway construction. The existing literature on the identification and assessment of subway construction safety risks(SCSR) is susceptible to the influence of subjective factors. Moreover, although existing studies have explored the interrelationships between different risks, these studies usually analyze the interrelationships of single risks, lack the study of risk chain transfer relationships, and fail to find out the key path of risk transfer. Therefore, this paper innovatively combines text mining, association rules and complex networks to deep mine subway construction safety incident reports and explore risk transfer process. Firstly, it uses text mining technology to identify subway construction safety risk; Then, association rules are introduced to explore the causal relationships among safety risk; Finally, the key safety risk and important transfer paths of subway construction safety accidents (SCSA) are obtained based on the complex network model. Research results show that (a) improper safety management, unimplemented safety subject responsibilities, violation of operation rules, non-perfect safety responsibilities system and insufficient safety education and training are the key safety risk in SCSA; (b) two shorter key risk transfer paths in the subway construction safety network can be obtained: insufficient safety education and training→lower safety awareness→violation of operation rules→safety accidents; insufficient safety checks or hidden trouble investigations→violation of operation rules→safety accidents; (c) in the process of risk transfer, the risk can be controlled by controlling the key nodes or cutting off the transfer path. The results of the study provide new ideas and methods for SCSR identification and influence element mining, which help safety managers propose accurate subway construction safety risk control measures.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

Unmanned construction machinery vehicles mostly carry work in bridges, tunnels, and outdoor open spaces. Obtaining accurate pose estimation of the entire vehicle and establishing a map of the surrounding environment is of great significance for path planning and control in the later stage. Traditional simultaneous localization and mapping (SLAM) schemes, which mostly use a single sensor, but there are problems with localization drift and mapping failure in scenarios where there are few geometric features and the environment is prone to degradation. Currently, the multi-sensor fusion strategy has been proven to be an effective solution and widely used in the field of unmanned vehicle localization and mapping. This paper proposes a SLAM framework that tightly couples a LiDAR, IMU and camera to achieve accurate and reliable pose estimation. The framework is based on LiDAR-inertial system(LIS) and factor graph optimization theory. Texture information provided by vision is integrated into the LiDAR-inertial odometry to generate a new visual-inertial subsystem(VIS).The two subsystems, VIS and LIS, can assist each other and work jointly. Through real vehicle tests, the system can perform incremental, real-time state estimation, reconstruct dense 3D point cloud maps,and effectively solve the problems of localization drift and mapping failure in the lack of geometric features or challenging construction environments. Meanwhile, the system has a safety redundancy mechanism. When any subsystem fails, the system can also operate normally, to ensure the reliability and robustness of vehicle positioning.

Building Information Modelling (BIM) has been more popular in the construction industry as a consequence of the many advantages it offers, such as increased productivity, improved project outcomes, and reduced expenses. However, there are many obstacles that must be overcome before BIM can be widely used. This research uses a poll of construction industry experts to investigate the challenges associated with using BIM in projects. Cost of implementation, inadequate standards and procedures, and a lack of knowledge with BIM were some of the hurdles that were measured in the study. Statistical techniques were used to examine the data, and the findings indicate that the high cost of implementation and the absence of sufficient standards and procedures are the two main obstacles to the widespread adoption of BIM. Problems with supply chain management and a lack of experience with BIM are also mentioned as obstacles. The report also suggests solutions, such as a more focused teaching effort on BIM-related issues and the creation of a specialised BIM curriculum. Professionals in the construction industry may utilise the study’s results to their advantage by expanding their knowledge of the obstacles standing in the way of widespread adoption of BIM.

The Agile Building Adaptation (AgiBuild) framework is the adoption and adaptation of the large-scale agile framework for building adaptation projects. The agile methodology is proven to drive innovation by focusing on adaptation to change and user centricity. Similarly, the authors envision that the AgiBuild framework can fundamentally change the way that buildings are re-designed, refurbished, and operated. The AgiBuild framework is developed from the need of the building adaptation industry to manage uncertainties, overcome communication barriers, and improve innovation. In this study, a literature review of Agile and its impact on building adaptation projects is undertaken. Based on this systematic literature review, this paper defines the AgiBuilt framework and provides its benefits and barriers to implementation. A key finding of the literature review is that leadership influence, and adequate training form the key foundation for the implementation of the AgiBuild Framework. In defining the AgiBuild framework, the paper describes its components and how its implementation is likely to proceed. The authors propose that by adopting the AgiBuild framework, the industry can transform itself into a highly innovative and user-centred industry to improve productivity and performance of the construction industry..

Visualization techniques are a powerful communication tool between construction stakeholders. The advancement of technology from 2D drawings to 3D models, Virtual Reality (VR), and Augmented Reality (AR) has emphasized the crucial role of efficient communication of ideas, designs, and concepts in preventing project delays and other issues in the Architecture, Engineering, and Construction (AEC) industry. Contemporary innovations such as web-based virtual reality cloud platforms that facilitate collaborative AEC projects and Head-mounted Displays that enable the viewing of VR environments are some of the latest technological developments that are emerging in the construction industry. These technological advances have the potential to improve communication, increase project efficiency, and enhance the quality of construction work. The purpose of this research is to identify existing trends and potential future directions by appropriating the state of the art of the intellectual growth of Virtual reality and Augmented Reality. The study used scientometric analysis in reviewing existing publications to scientifically map the evolution of VR and AR in the AEC sector. The study observed an emerging but little amount of publications on VR and AR in construction. While Africa contributes little significance, advancement in VR and AR research is led by United States and America. The study expresses concern over the dearth of research and the low amount of collaborations amongst institutions in diverse countries. The study concludes that VR and AR research in the AEC sector must be afforded the needed focus and attention. In recent times, the global Coronavirus pandemic has shown that technology such as VR and AR is inevitable in the success of a project.

Design for Manufacture and Assembly (DfMA) in architectural, engineering, and construction (AEC) industry is attracting the attention of designers, practitioners, and construction project stakeholders. Digital fabrication (Dfab) and design for additive manufacturing (DfAM) practices are found in current needs for further research and development. The DfMA's conceptual function is to maximize the process efficiency of Dfab and AM building projects. This work reviewed 171 relevant research articles over the past few decades. The concept of DfMA and the fundamentals of DfMA in building and construction were explored. In addition, DfMA procedures associated with Dfab and DfAM, as well as its AM assembly process, were discussed. Lastly, the current machine learning research on DfMA in construction was also highlighted. Large research gaps in the DfMA for Dfab and DfAM can be filled to increase operational efficiency and sustainable practices.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

Concrete, as one of the essential construction materials is responsible for a vast amount of emissions. Using recycled materials and gray water can considerably contribute to the sustainability aspect of concrete production. Thus, finding a proper replacement for fresh water, in the production of concrete, is significant. The usage of industrial wastewater, instead of water in the concrete can is considered in this paper. In this study, 450 concrete samples are produced with different amounts of wastewater. The mechanical parameters such as slump, compressive strength, water absorption, tensile strength, electrical resistivity, rapid freezing, half-cell potential, and appearance are investigated. The results showed that the usage of industrial wastewater does not significantly change the main characteristics of concrete. Although, increasing the concentration of the wastewater can decrease durability and strength features nonlinearly.

We study the hadron-quark hybrid equation of state (EOS) of compact-star matter. The Nambu—Jona-Lasinio (NJL) local SU(3) model with vector-type interaction is used to describe the quark matter phase, while the relativistic mean field (RMF) theory with scalar-isovector $\delta$-meson effective field adopted to describe the hadronic matter phase. It is shown that the larger the vector coupling constant, the lower the threshold density for the appearance of strange quarks. For a sufficiently small value of the vector coupling constant, the functions of the mass dependence on the baryonic chemical potential have regions of ambiguity which leads to a phase transition in non-strange quark matter with an abrupt change in the baryon number density. We show that within the framework of the NJL model, the hypothesis on the absolute stability of strange quark matter is not realized. In order to describe the phase transition from hadronic matter to quark matter, the Maxwell's construction is applied. It is shown that the greater the vector coupling, the greater the stiffness of the EOS for quark matter and the phase transition pressure. Our results indicate that the infinitesimal core of the quark phase, formed in the center of the neutron star, is stable.

Existing rammed earth construction methods have disadvantages such as increased initial costs for manufacturing the large formwork and increased labor costs owing to the labor-intensive construction techniques involved. To address the limitations of existing rammed earth construction methods, an autonomous rammed earth construction method is introduced herein. As this autonomous rammed earth construction method uses a modular formwork, alternative materials must be used in the construction to satisfy the requirements for the early-age binder performance. Accordingly, this study evaluates the use of an epoxy emulsion composed of epoxy and a hardener to enhance the performance of the binder. Preliminary experiments were conducted to determine the optimal formulation of the epoxy emulsion, following which the compressive strength, water loosening, shrinkage, rate of mass change, and microstructure of several red clay binder specimens with and without epoxy emulsion were analyzed at early ages. The results confirmed that the epoxy emulsion can be applied to satisfy the performance requirements for autonomous rammed earth construction by improving the durability and strength of the binder at early ages.

Buildings use 30-40 % of all energy resources and are thus their main consumers in modern society. Moreover, buildings require a vast amount of different raw materials. During the last two decades, several green building certifications have been created in order to consider social, economic and environmental aspects of sustainability of buildings. One of the most famous and widely used of these certifications is Leadership in Energy and Environmental Design (LEED). So far, the use of LEED has concentrated in the US and other developed countries. One reason that restricts the use of this point-based system certification in developing countries is the limited data about its costs. In this study, the extra cost of the certification process will be evaluated besides the changes needed in the design of the building to reach the points required by LEED. At the first stage, the number of points the case study earns in its current format (Scenario 1) were found out, then the cost difference of getting either the Certified (Scenario 2) or Silver (Scenario 3) level LEED certification for the building was studied. It was found that besides some technical considerations, filling the criteria of the Certified and Silver level increases the total costs of construction by 3.4% and 5.9%. Further improvement of the building’s energy efficiency would enable the attainment of a higher-level certification. The results of the study could help to promote the use of green building certifications in Western Asia.

In the Korean construction industry, legal and institutional safety management improvements are continually being pursued. However, there was a 4.5% increase in the number of workers’ deaths at construction sites in 2017 compared to the previous year. Failure to wear safety helmets seems to be one of the major causes of the increase in accidents, and so it is necessary to develop technology to monitor whether or not safety helmets are being used. However, the approaches employed in existing technical studies on this issue have mainly involved the use of chinstrap sensors and have been limited to the problem of whether or not safety helmets are being worn. Meanwhile, improper wearing, such as when the chinstrap and harness fixing of the safety helmet are not properly tightened, has not been monitored. To remedy this shortcoming, a sensing safety helmet with a three-axis accelerometer sensor attached was developed in this study. Experiments were performed in which the sensing data were classified whether the safety helmet was being worn properly, not worn, or worn improperly during construction workers’ activities. The results verified that it is possible to differentiate among wearing status of the proposed safety helmet with a high accuracy of 97.0%

The determination of the non-loading condition of the rail cable shifting (RCS) system, which consists of main cables, hangers and rail cables, is the premise of the girder erection for the long-span suspension bridges. An analytical form-finding analysis model of shifting system is established according to the basic assumptions of flexible cable structures. Herein, the rail cable is discretized into segmental linear cable elements and the main cable is discretized into segmental catenary elements. Moreover, the calculation and analysis equation of each member and their iterative solutions are derived by taking the elastic elongation of the sling into account. In addition, by taking the girder construction of Aizhai suspension bridge as engineering background, a global scale model of the RCS system is designed and manufactured; also the test system and working conditions are established. The comparison between the test results and analytical results shows the presented analytical method is correct and effective. The process is simplified in the analytical method, and the computational results and precision can satisfy the practical engineering requirements. In addition, the proposed method is suitable to apply to the computation analysis of similar structures.

In this paper the development process of a deployable modular sandwich panelized system for rapid assembly building construction is presented, and its structural performance under some different action effects is investigated. This system, which includes an innovative sandwich panel and its integrated connections, can be used as structural walls and floors in quickly assembled post-disaster housing, as well as load bearing panels for pre-fabricated modular construction and semi-permanent buildings. Panels and connections are composed of a pneumatic fabric formwork, and two 3-D high-density polyethylene (HDPE) sheets as the skins, filled with high-density rigid Polyurethane (PU) foam as the core. HDPE sheets manufactured with a studded surface considerably enhance the stress distribution, buckling performance and delamination strength of the sandwich panel under various loading conditions. The load-carrying behaviour of the system in accordance with some ASTM standards is presented here. The results show the system satisfies the codes criteria regarding semi-permanent housing.

In the contemporary construction management, poor project performance, cost overrun, and low-quality construction have become a central point of attention for improving project performance including information, interaction and communication management. virtual design and construction and building information modelling play indispensable role in improving the project performance. The aim of this study is to propose a Virtual Information Modeling as a novel information and communication technology method with potential to overcome problems in the construction industry. Using one-sample t test with Kolmogorov-Smirnov approach, we analysed data collected from structured questionnaire survey involving project managers working at architecture, engineering and construction industries in Tehran, Iran. The results suggest that the most important benefits and challenges of using Virtual Information Modeling are related to the area of integration, and implementation of Virtual Information Modeling has the greatest impact on this area of project management knowledge. Thus, integration should be considered a top priority for construction companies implementing Virtual Information Modeling in their projects. Policymakers should understand that careful management of virtual information is essential for improving the performance of projects and enhancing the process efficiency.

The evaluation of nanostructured biomaterials and medicines is associated with 2D cultures that provide insight into the biological mechanisms at the molecular level, while critical aspects of the tumor microenvironment (TME) are provided by the study of animal xenograft models. More realistic models that can histologically reproduce human tumors are provided by tissue engineering methodologies of co-culturing cells of varied phenotypes, to provide 3D tumor spheroids that recapitulate the dynamic TME in 3D matrices. The novel approaches of 3D tumor models are combined with tumor tissue engineering (TTE) scaffolds including hydrogels, bioprinted materials, decellularized tissues, fibrous and nanostructured matrices. This review focuses on the use of nanostructured materials in cancer therapy and regeneration, and the development of realistic models for studying TME molecular and immune characteristics. Tissue regeneration is an important aspect of TTE scaffolds for restoring the normal function of the tissues, while providing cancer treatment. Thus, this article reports recent advancements on the development of 3D TTE models for antitumor drug screening, studying of tumor metastasis, and tissue regeneration. Also, this review identifies the great opportunities of 3D TTE scaffolds in the evaluation of the immunological mechanisms and processes involved in the application of immunotherapies.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

Immediate load of full-arch rehabilitations over implants, specially over 4 implants are very well documented in the literature. More recently, the use of computed surgical guides to help the planning and the execution of these treatments, in many situations without the need of raising a flap, and diminishing the appearance of hematomas, bleeding and with less trauma to the patient has gained preference among implantologists. The objective of this case report is to show a clinical case of an immediate load full-arch fixed rehabilitation over 4 implants produced by 3D printing manufacturing technology, and placed with a computed surgical guide, in the same appointment, and the 24 months follow-up. The patient returned after 3 months to replace the immediate temporary fixed prosthesis for a new one, with metallic bar, better teeth and more delicate. Soft and hard tissue around the implants seemed to be stable, without signs of inflammation, either on the 3 or the 24 months follow-up. 3D printing of implants by direct metal laser sintering is a technology that seems to be promising for oral implantology, with solid studies showing reliable results, as seen in this single case. More clinical studies are necessary to testify its efficacy.

Characters are one of the most important elements in composing digital animation. The appear-ance and voice of a character should be designed to express the personality and values of the character. However, it is not easy for animation producers to harmoniously match the appear-ance and voice of a character. Advances in deep learning technology have made it possible to overcome this limitation. To achieve this, firstly, an audio-visual dataset of characters is required. In this study, we construct and verify a Korean audio-visual dataset consisting of frontal face im-ages of various characters and short voice clips. We developed an application that can automati-cally extract the frontal face image and a short voice clip of a character by collecting videos up-loaded to YouTube. Through this, a dataset consisting of a total of 1,522 face images and a total of 7,999 seconds of voice clips was built based on 490 characters. Furthermore, we automatically la-bel characters by gender and age to validate the dataset. The dataset built in this study is expected to be used in various deep learning fields, such as classification, generative adversarial networks, and speech synthesis.

The 3D reconstruction of vermiculite-based sealing material was carried out based on CT scanning experiments and Avizo software. The precision and representation of the reconstructed digital core were tested by calculating the pore structure parameters and comparing them with the experimental results of mercury compression. Avizo is a perfect interface with Fluent software to perform micro-scale seepage simulation to explore the distribution of pressure and velocity fields during fluid transport. In this paper, a new approach is proposed to study the penetration leakage of non-metallic gaskets by using equivalent pore networks.

The three-dimensional Ising model on the m$\times$n$\times$l cubic lattice with the screw boundary condition along the ${\bf X}$ direction and the periodic boundary conditions along both ${\bf Y}$ and ${\bf Z}$ directions is exactly solved by using the $2^{mn}$-dimensional representation of the rotation group in $2mn$-dimensions, similar to the Kaufman's spinor approach in two dimensions. The exact partition function is obtained from two sets of $2^{mn-1}$ eigenvalues of the $2^{mn}$-dimensional transfer matrix {\bf V} corresponding to the even and odd eigenvectors, respectively. Such the eigenvalues are determined by the angles of the 2mn-dimensional rotation associated with {\bf V}.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

Existing methods for 3D human pose estimation mainly divide the task into two stages. The first stage identifies the 2D coordinates of the human joints in the input image, namely the 2D human joint coordinates. The second stage uses the results from the first stage as input to recover the depth information of human joints from the 2D human joint coordinates to achieve 3D human pose estimation. However, the recognition accuracy of the two-stage method relies heavily on the results of the first stage and includes too many redundant processing steps, which reduces the inference efficiency of the network. To address these issues, we propose the EDD, a fully End-to-end 3D human pose estimation method based on transformer architecture with Dual Decoders. By learning multiple human poses, the model can directly infer all 3D human poses in the image using a pose decoder, and then further optimize the recognition result using a joint decoder based on the kinematic relations between joints. With the attention mechanism, this method can adaptively focus on the most relevant features to the target joint, effectively overcoming the feature misalignment problem in the human pose estimation task and greatly improving the model performance. Any complex post-processing step, such as non-maximum suppression, is eliminated, further improving the efficiency of the model. The results show that the method achieves an accuracy of 87.4% on the MuPoTS-3D dataset, significantly improving the accuracy of end-to-end 3D human pose estimation methods.

The rapid development of electrochemical CO2 reduction offers a promising route to convert in-termittent renewable energy into products of high value-added fuels or chemical feedstocks. However, low faradaic efficiency, low current density, and a narrow potential range still limited the large-scale application of CO2RR electrocatalyst. Herein, monolith 3D bi-continuous nano-porous Bismuth (np-Bi) electrodes are fabricated via a simple one-step electrochemical dealloying strategy from Pb-Bi binary alloy. The unique bi-continuous porous structure ensures highly effective charge transfer, meanwhile the controllable millimeter-size geometric porous structure enables easy catalyst adjustment to expose highly suitable surface curvatures with abundant reactive sites. This results in a high selectivity of 92.6% and superior potential window (400 mV, selectivity >88%) for electrochemical reduction of carbon dioxide to formate. Our scalable strategy provides a feasible pathway for mass-producing high-performance and versatile CO2 electrocatalysts.

A key component of efforts to identify the biological and drug-specific aspects that contribute to therapeutic failure or unexpected exposure-associated toxicity is the study of drug-intestinal barrier interactions. While methods supporting such assessments are widely described for human therapeutics, there is relatively little information available for similar evaluation in support of veterinary pharmaceuticals. There is, therefore, a critical need to develop novel approaches for evaluating drug-gut interactions in veterinary medicine. Three-dimensional (3D) organoids can address these difficulties in a reasonably affordable system that circumvents the need for more invasive in vivo assays in live animals. However, a first step in the development of such systems is understanding organoid interactions in a 2D monolayer. Given the importance of orally administered medications for meeting the therapeutic need of companion animals, we demonstrate growth conditions under which canine colonoid-derived intestinal epithelial cells survive, mature, and differentiate into confluent cell systems with high monolayer integrity. We further examine the applicability of this canine colonoid-derived 2D model to assess the permeability of three structurally diverse, passively absorbed β-blockers (e.g., propranolol, metoprolol, and atenolol). Both absorptive and secretive apparent permeability (Papp) of these drugs at two different pH conditions were evaluated in canine colonoid-derived monolayers and were compared with that of Caco-2 cells. This proof-of-concept study provides promising preliminary results with regard to the utility of canine-derived organoid monolayers for species-specific assessments of therapeutic drug passive permeability.

Smart health applications have received significant attention in recent years. Novel applications hold significant promise to overcome many of the inconveniences faced by persons with disabilities throughout daily living. For people with blindness and low vision (BLV), environmental perception is compromised, creating myriad difficulties. Precise localization is still a gap in the field and is critical to safe navigation. Conventional GNSS positioning cannot provide satisfactory performance in urban canyons. 3D mapping-aided (3DMA) GNSS may serve as an urban GNSS solution, since the availability of 3D city models has widely increased. As a result, this study developed a real-time 3DMA GNSS-positioning system based on state-of-the-art 3DMA GNSS algorithms. Shadow matching was integrated with likelihood-based ranging 3DMA GNSS, generating positioning hypothesis candidates. To increase robustness, the 3DMA GNSS solution was then optimized with Doppler measurements using factor graph optimization (FGO) in a loosely-coupled fashion. This study also evaluated positioning performance using an advanced wearable system’s recorded data in New York City. The real-time forward processed FGO can provide a root-mean-square error (RMSE) with about 21 m. The RMSE drops to 16 m when the data is post-processed with FGO in a combined direction. Overall results show that the proposed loosely-coupled 3DMA FGO algorithm can provide a better and more robust positioning performance for the multi-sensor integration approach used by this wearable for persons with BLV.

Along with the popularity of the Internet, people are exposed to more and more ways of micro-videos, and a huge amount of micro-video data has emerged. micro-videos have gradually become the Internet content preferred by the public, and a large number of micro-video apps have also emerged, such as Tiktok and Kwai. Intelligent classification and mining of micro-videos can greatly enhance user experience, improve business operation efficiency and enhance user experience. Through deep intelligent analysis and mining of micro-videos, important information in micro-videos can be extracted to provide an important basis for beautifying videos, content appreciation, video recommendation, content search, etc. In the past, content understanding for short videos often used human work annotation, but in recent years, with the great success of deep convolutional neural networks in image recognition, short video content understanding based on this method has gradually developed. Nowadays, most recognition algorithms extract the feature representation of each frame independently and then fuse them. However, while extracting the feature representation, some low-level semantic features are lost, which makes the algorithm unable to accurately distinguish the category of the video. At present, the algorithm of micro-video recognition based on deep learning has surpassed the iDT algorithm, making these traditional methods fade out of people’s view. In this paper according to the micro-video classification task, a new network model is proposed to concatenate features of each modality into the overall features of various modalities through the network, and then fuse the various modal features with the attention mechanism to obtain the whole micro-video features, which will be used for classification. In order to verify the effectiveness of the algorithm proposed in this paper, experiments are conducted in the public dataset, and it is shown the effectiveness of our model.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

Radar observation data with high temporal and spatial resolution are used in the data assimilation experiment to improve precipitation forecast of a numerical model. The numerical model considered in this study is Weather Research and Forecasting (WRF) model with double-moment 6-class microphysics scheme (WDM6). We calculated radar equivalent reflectivity factor using higher resolution WRF and compared with radar observations in South Korea. To compare the precipitation forecast characteristics of three-dimensional variational (3D-Var) assimilation of radar data, four experiments are performed based on different precipitation types. Comparisons of the 24-h accumulated rainfall with Automatic Weather Station (AWS) data, Contoured Frequency by Altitude Diagram (CFAD), Time Height Cross Sections (THCS), and vertical hydrometeor profiles are used to evaluate and compare the accuracy. The model simulations are performed with and with-out 3D-VAR radar reflectivity, radial velocity and AWS assimilation for two mesoscale convective cases and two synoptic scale cases. The radar data assimilation experiment improved the location of precipitation area and rainfall intensity compared to the control run. Especially, for the two convective cases, simulating mesoscale convective system was greatly improved.

The initial stability after implantology is paramount to the survival of the dental implant and the surface roughness of the implant plays a vital role in this regard. The characterisation of surface topography is a complicated branch of metrology, with a huge range of parameters available. Each parameter contributes significantly towards the survival and mechanical properties of 3D-printed specimens. The purpose of this paper is to experimentally investigate the effect of surface roughness of 3D-printed dental implants and 3D-printed dogbone tensile samples under areal height (Ra) parameters, amplitude parameters (average of ordinates), skewness (Rsk) parameters and mechanical properties. During the experiment, roughness values were analysed and the results showed that the skewness parameter demonstrated a minimum value of 0.596%. The 3D-printed dental implant recorded Ra with a 3.4 mm diameter at 43.23% and the 3D-printed dental implant with a 4.3 mm diameter at 26.18%. Samples with a complex geometry exhibited a higher roughness surface, which was the greatest difficulty of additive manufacturing when evaluating surface finish. The results show that when the ultimate tensile stress (UTS) decreases from 968.35 MPa to 955.25 MPa, Ra increases by 1.4% and when UTS increases to 961.18 MPa, Ra increases by 0.6%. When the cycle decreases from 262142 to 137433, Ra shows that less than a 90.74% increase in cycle is obtained. For 3D-printed dental implants, the higher the surface roughness, the lower the mechanical properties, ultimately leading to decreased implant life and poor performance.

Three-dimensional (3D) printing techniques have received considerable focus in the area of bone engineering due to its precise control in the fabrication of complex structures with customizable shapes, internal and external architectures, mechanical strength, and bioactivity. In this study, we design a new composition biomaterial consisting of polylactic acid (PLA), and halloysite nanotubes (HNTs) loaded with zinc nanoparticles (PLA+H+Zn). The hydrophobic surface of the 3D printed scaffold was coated with two layers of fetal bovine serum (FBS) on the sides and one layer of NaOH in the middle. Additionally, a layer of gentamicin was coated on the outermost layer against bacterial infection. Scaffolds were cultured in standard cell culture medium without the addition of osteogenic medium. This surface modification strategy improved material hydrophilicity and enhanced cell adhesion. Pre-osteoblasts cultured on these scaffolds differentiated into osteoblasts and proceeded to produce a type I collagen matrix and subsequent calcium deposition. 3D printed scaffolds formed from this composition possessed high mechanical strength and showed an osteoinductive potential. Furthermore, the external coating of antibiotics not only preserved the previous osteogenic properties of the 3D scaffold but also significantly reduced bacterial growth. Our surface modification model enabled the fabrication of a material surface that was hydrophilic and antibacterial, simultaneously, with an osteogenic property. The designed PLA+H+Zn may be a viable candidate for the fabrication of customized bone implants.

Paclitaxel is a natural, highly lipophilic anti proliferative drug widely used in medicine. We have studied the release of tritium-labeled paclitaxel (³H-PTX) from matrices destined for the coating of vascular stents and produced by the electrospinning method from the solutions of polycaprolactone (PCL) with paclitaxel (PTX) in hexafluoisoropropanol (HFIP) and/or solutions of PCL with PTX and human serum albumin (HSA) in HFIP or HIFP-dimethyl sulphoxide (DMSO) blend. The release of PTX has been shown to depend on the solvent and the composition of electrospinning solution, as well as the composition of the surrounding medium, particularly the concentration of free PTX and PTX-binding biomolecules present in human serum. It was shown that 3D matrices can completely release PTX without weight loss. Two-phase PTX release from optimized 3D matrices was obtained: ~27% of PTX was released in the first day, another 8% were released over the next 26 days. Wherein ~2.8%, ~2.3%, and ~0.25% of PTX was released on day 3, 9, and 27, respectively. Considering PTX toxicity, the rate of its diffusion through the arterial wall, and the data obtained the minimum cytostatic dose of the drug in the arterial wall will be maintained for at least three months.