There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

Surfaces of additively manufactured metal parts from powder-based processes typically show powder particle agglomerations and other features, resulting in high surface roughness. Proper characterization of those surfaces is necessary in order to assess part quality with respect to coatability, mechanical performance or corrosion resistance for use in aerospace, automotive, medical and more industrial applications. Optical surface texture measurement allows for collection of areal surface data, while the established contact stylus method only captures line profile data. When applying optical methods for surface topography measurements, proper data acquisition and post-processing in order to assess surface texture may be complex. A number of variables can be adjusted, such as different measurement settings, approaches to outlier removal, evaluated area size or form removal. This work shows the influence of selected z-range prior to measurement and the influence of choosing pre-defined outlier removal settings in MountainsMap 9.2 on selected ISO 25178-2:2022 parameters calculated from data obtained from confocal microscopy for as-built Ti6Al4V from laser powder bed fusion. The aim is to show the influence of variation in measurement and post-processing on calculated surface texture parameters and stress the importance of proper documentation in order to achieve reproducibility of data for quality management.

A drone performs comparable function to a laser scanner in the construction quality monitoring, following Scan-to-BIM process. Both technologies digitally capture the as-is environment into the computer and the data captured is transferred to a BIM world to create accurate as-built models. Although the laser scanner is the dominant method of the Scan-to-BIM process, a number of digital professionals point drawbacks of the method and present the drone is an alternative that can improve the drawbacks thereby leading to UAV-to-BIM process in parallel with the Scan-to-BIM. Korean construction industry plans to utilize the two technologies for monitoring construction operation quality in major public projects by 2025. While contractors need competent engineers to be competitive in the projects, the two technology applications are not so popular to the construction projects in Korea and very few experts skillful and knowledgeable of the technologies are available. Korean universities are requested to develop the curriculum of the technologies for the contractors. To be successful in progressing the curriculum, it is very essential to implement a preliminary study with the technologies minimizing the potential failure in operating the curriculum later on. This study performs empirical research on the technologies and identify valuable lessons beneficial to develop the UAV-to-BIM curriculum for the construction engineers.

Laser Powder Directed Energy Deposition (LP-DED) is an Additive Manufacturing process in which a laser beam is used to generate a melt pool onto a substrate. The additional material, in form of powder material, is fed into the generated melt pool and a raised track is obtained. The LP-DED process is very powerful for different applications such as the repair operations and the production of functionally graded material, however the application is still limited and one of the main reasons is related to the lack of knowledge in the physics of the process mechanisms. The process is influenced by a huge number of parameters and three main mechanisms can be identi-fied. These mechanisms are the powder flow, the generation of the molten pool and the solidifica-tion process and for each of these mechanisms the process parameters have a different relevance. In this paper, a review of the main mechanisms and the relationship between the process parame-ters and the outcome of each step of the process is presented.

Understanding cell migration is a key step to unravel many physiological phenomena and predict several pathologies, like cancer metastasis. In particular, mechanical confinement has been proved to be a key factor in the cellular migration strategy choice. As our insight in the field improves, new tools are needed in order to empower biologists’ analysis capabilities. In this framework, microfluidic devices have been used to engineer the mechanical stimuli and to investigate cellular migration response in a more controlled way. In this work, we will review the existing technologies employed in the realization of microfluidic cellular migration assays, namely soft lithography of PDMS and hydrogels and femtosecond laser micromachining. We will give an overview of the state of the art of these devices, focusing on the different geometrical configurations that have been exploited to study specific aspects of cellular migration. Our scope is to highlight the advantages and possibilities given by each approach and to envisage the future developments in in-vitro migration studies under mechanical confinement in microfluidic devices.

Recent expansion in data sharing has created unprecedented opportunities to explore structure-function linkages in ecosystems across spatial and temporal scales. However, characteristics of the same data product, such as resolution, can change over time or spatial locations, as protocols are adapted to new technology or conditions, which may impact the data’s potential utility and accuracy for addressing end user scientific questions. The National Ecological Observatory Network (NEON) provides data products for users from 81 sites and over a planned 30-year time frame, including discrete return Light Detection and Range (LiDAR) from an airborne observatory platform. LiDAR is a well-established and increasingly available remote sensing technology for measuring three-dimensional (3D) characteristics of ecosystem and landscape structure, including forest structural diversity. The LiDAR product that NEON provides can vary in point density from 2 – 25+ points/m² depending on instrument and acquisition date. We used NEON LiDAR from five forested sites to (1) identify the minimum point density at which structural diversity metrics can be robustly estimated across forested sites from different ecoclimatic zones in the USA and (2) to test the effects of variable point density on the estimation of a suite of structural diversity metrics and multivariate structural complexity types within and across forested sites. Twelve out of sixteen structural diversity metrics were sensitive to LiDAR point density in at least one of the five NEON forested sites. The minimum point density to reliably estimate the metrics ranged from 2.0 to 7.5 pt/m^2, but our results indicate that point densities above 7-8 pt/m² should provide robust measurements of structural diversity in forests for temporal or spatial comparisons. The delineation of multivariate structural complexity types from a suite of 16 structural diversity metrics was robust within sites and across forest types for a LiDAR point density of 4 pt/m² and above. This study shows that different metrics of structural diversity can vary in their sensitivity to the resolution of LiDAR data and users of these open-source data products should consider the point density of their data and use caution in metric selection when making spatial or temporal comparisons from these datasets.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

Time evolution operators of a strongly ionizing medium are calculated by a time-dependent unitary transformation (TDUT) method. The TDUT method has been employed in quantum mechanical system composed of discrete states. This method is especially helpful for solving molecular rotational dynamics in quasi-adiabatic regimes because the strict unitary nature of the propagation operator allows us to set the temporal step size large; a tight limitation on the temporal step size ($\delta t <<1$) can be circumvented by the strict unitary nature. On the other hand, in a strongly ionizing system where the Hamiltonian is not Hermitian, the same approach cannot be directly applied because it is demanding to define a set of field-dressed eigenstates. In this study, the TDUT method was applied to the ionizing regime using the Kramers-Henneberger frame, in which the strong-field-dressed discrete eigenstates are given by the field-free discrete eigenstates in a moving frame. Although the present work verifies the method for a one-dimensional atom as a prototype, the method can be applied to three-dimensional atoms, and molecules exposed to strong laser fields.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

Interaction of an electromagnetic field with matter in a laser cavity without the assumption of a fixed direction of the transverse electric field, described by the two-level Maxwell-Bloch equations, is studied. By using a perturbative nonlinear analysis, performed near the laser threshold, we report on the derivation of the laser (3+1)D vectorial complex cubic-quintic complex Ginzburg-Landau equation. Furthermore, we study the modulational instability of the plane waves both theoretically using the linear stability analysis, and numerically, using direct simulations via the split-step Fourier method. The linear theory predicts instability for any amplitude of the primary waves. Our numerical simulations confirm the theoretical predictions of the linear theory as well as the threshold of the amplitude of perturbations. The system understudy shows a deep dependence on the laser cavity parameters, for which there appear wave patterns in accordance with the predictions from the gain spectrum.

Non-destructive testing of metallic objects that may contain embedded defects of different sizes is an important application in many industrial branches for quality control. Most of these techniques allow defect detection and its approximate localization, but very few give enough information for its 3D reconstruction. Here we present a hybrid laser – transducer system that combines remote laser-generated ultrasound excitation and non-contact ultrasonic transducer detection. This fully non-contact method gives access to separating scan areas on different object’s faces and defect details from different angles/perspectives can be analysed. This hybrid system can analyse the whole object’s volume data and allow a 3D reconstruction image of the embedded defects. As a novelty for the signal processing improvement, we use a 2D apodization window filtering technique, applied along with the synthetic aperture focusing algorithm in order to remove the undesired effects of side lobes and wide-angle reflections of propagating ultrasound waves, thus, enhancing the resulting 3D image of the defect. We provide both qualitative and quantitative volumetric results with high accuracy and resolution compared with conventional techniques.

The use of commodity polymers such as polypropylene (PP) is key to open new market segments and applications for the additive manufacturing industry. Technologies such as powder-bed fusion (PBF) can process PP powder; however, much is still to learn concerning process parameters for reliable manufacturing. This study focusses in the process-property relationships of PP using laser-based PBF. The research presents an overview of the intrinsic and the extrinsic characteristic of a commercial PP powder as well as fabrication of tensile specimens with varying process parameters to characterize tensile, elongation at break, and porosity properties. The impact of key process parameters, such as power and scanning speed are systematically modified in a controlled design of experiment. The results were compared to the existing body of knowledge; the outcome is to present a process window and optimal process parameters for industrial use of PP. The computer tomography data revealed a highly porous structure inside specimens ranging between 8.46% and 10.08%, with porosity concentrated in the interlayer planes in the build direction. The results of the design of experiment for this commercial material show a narrow window of 0.122 ≥ Ev ≥ 0.138 J/mm³ led to increased mechanical properties while maintaining geometrical stability.

Additive manufacturing (AM) provides customization of the microstructure and mechanical properties of components. Selective laser melting (SLM) is the commonly used technique for processing high strength Aluminum alloys. Selection of SLM process parameters could control the microstructure of fabricated parts and their mechanical properties. However, process parameter limits and defects inside the as-built parts present obstacles to customized part production. This study is the second part of a comprehensive work that investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. Mechanical properties of the parts were illustrated by regression models generated with design of experiment (DOE) analysis. The results reported in this study were compared to previous studies, illustrating how the process parameters and powder characteristics could affect the quality of produced parts.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

A potassium bromide KBr material, which has been widely used as the key element in the Fourier spectrometers and as the output window of the IR-lasers, has been studied with good advantage via applying the carbon nanotubes in order to modify the potassium bromide surface. The laser oriented deposition method has been used to place the carbon nanotubes at the matrix material surface in the vertical position at the different electric field varied from 100 to 600 V×cm-1. The main idea of the improvement of the spectral properties of the potassium bromide structure is connected with the fact that the refractive index of the carbon nanotubes is substantially less than the refractive index of the studied material, and the small diameter of the carbon nanotubes allows one to embed these nano-objects in the voids of the lattice of the model matrix systems. Moreover, the mechanical characteristics and wetting features of the potassium bromide structures have been investigated under the condition mentioned above. Analytical and quantum-chemical simulations have supported the experimental results.

The use of the LMD technology as a manufacturing and repairing technique in industrial sectors like the die and mold and aerospace is increasing within the last decades. Research carried out in the field of LMD process situates argon as the most usual inert gas, followed by nitrogen. Some leading companies have started to use helium and argon as carrier and shielding gas, respectively. There is therefore a pressing need to know how the use of different gases may affect the LMD process due to there is a lack of knowledge with regard to gas mixtures. The aim of the present work is to evaluate the influence of a mixture of argon and helium on the LMD process by analyzing single tracks of deposited material. For this purpose, special attention is paid to the melt pool temperature, as well as to the characterization of the deposited clads. The increment of helium concentration in the gases of the LMD processes based on argon will have three effects. The first one is a slightly reduction of the height of the clads. Second, an increase of the temperature of the melt pool. Last, smaller wet angles are obtained for higher helium concentrations.

Manipulation of micro- and nano-sized objects with optical tweezers is a well established, albeit still evolving technique. While many objects can be trapped directly with focused laser beam(s), for some applications indirect manipulation with tweezers-operated tools is preferred. We introduce a simple, versatile micro-tool operated with holographic optical tweezers. The 40 µm long dumbbell-shaped tool, fabricated with two-photon laser 3D photolithography has two beads for efficient optical trapping and a probing spike on one end. We demonstrate fluids viscosity measurements and vibration detection as examples of possible applications.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

Mode locked pulse generation has been reported using both active and passive mode locking schemes. Active mode locking technique has been proven to be an effective way to generate high-repetition-rate pulses by incorporating a modulator inside the laser cavity. Compared to actively mode locked lasers, passively mode locked lasers can generate pulse train at ultrashort pulse width but with relatively lower repetition rate. Thus, it is a brilliant idea to build a hybrid mode locked system combining both active and passive mode lockers. In this review, several hybrid mode locked fiber ring laser systems are discussed and summarized. Hybrid mode locking is a promising method to generate high speed ultrashort optical pulses for fiber-optic telecommunication system.

High average power narrow-linewidth tunable solid-state lasers in the wavelength region between 2 to 3 μm are attractive light sources for many applications. This paper reports a narrow-linewidth widely-tunable laser system based on the polycrystalline Cr2+:ZnSe elements pumped by the repetitively-pulsed 2.1 µm Ho3+:YAG laser operating at the tens of kilohertz pulse rate. An advanced procedure of ZnSe-element doping and surface improvement was applied to increase the laser-induced damage threshold, which resulted in an increase of the output power of the Cr2+:ZnSe laser system. The high-average-power laser system comprised double master-oscillators and power amplifiers: Ho3+:YAG and Cr2+:ZnSe laser oscillators, and Ho3+:YAG and Cr2+:ZnSe power amplifiers. The output wavelength was widely tuned within 2.3-2.7 µm by an acousto-optical tunable filter inside the Cr2+:ZnSe master oscillator cavity. The narrow-linewidth operation at the pulse repetition rate of 20-40 kHz in a high-quality beam with the average output power up to 9.7 W was demonstrated.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

Dissimilar welds between ferritic and austenitic steels represent a good solution for exploiting the best performance of stainless steels at high and low temperatures and in aggressive environments, while minimizing costs. Therefore, they are widely used in nuclear and petrochemical plants, however, due to the different properties of the steels involved, the welding process can be challenging. Fusion welding can be specifically addressed to connect low-carbon, or low-alloy steels, with high-alloy steels, which have similar melting point. Welding of thick plates can be performed with electric arc in multiple passes or in a single pass by means of a laser beam equipment. Since microstructure and consequently mechanical properties of the weld are closely related to composition, the choice of the filler metal and processing parameters, which in turn affects the dilution rate, plays a fundamental role. Numerous technical solutions were proposed for welding dissimilar steels and much research was developed on the weldment metallurgy; therefore, this article is aimed at a review of the most recent scientific literature on the issues relating to the fusion welding of ferritic / austenitic steels. Two specific sections are dedicated respectively to electric arc and laser beam welding; finally, metallurgical issues, related to dilution and thermal field are debated in the discussion section.

The radiation stability of polymer test objects fabricated by direct laser writing is studied. The two groups of 6 cubes (50×50×50 μm3) were printed on a common silicon substrate. 6 cubes were irradiated with X-rays in the synchrotron radiation beam (12 keV, 1010 photons/mm2/s), the other 6 kept non-irradiated for the reference. In each group, the fabrication parameters (laser power and slicing step) were uniformly varied from cube to cube. Each irradiated cube was exposed with the dose of 1013 X-ray photons. The calibration of this dose in the radiological units (Gy) was carried out using the tissue-equivalent thermoluminescent detectors (TLD-800). The corresponding exposition dose was estimated as 30 kGy for each cube. The radiation effects were evaluated by Raman spectroscopy and by morphological changes observed with the raster electron microscope. The primary radiation effect appears in the essential increase of the polymerization degree with consuming carbon-carbon double bonds in favor of the polymer cross-linking. Only one cube of 6 has changed the size and shape due to this effect, while the others retained the initial shape. Morphological changes are connected with the improper fabrication parameters (laser power and slicing step). Properly fabricated objects withstand the X-rays of the synchrotron radiation beam.

Three-layer structures based on various multi-component films of III–V semiconductors heavily doped with Fe were grown by pulsed laser sputtering of InSb, GaSb, InAs, GaAs and Fe solid targets. The structures comprising InAsSb:Fe, InGaSb:Fe and InSb:Fe layers with Fe concentrations up to 24 at. % separated by GaAs spacers were deposited on (001) i-GaAs substrates at 200ºC. Transmission electron microscopy showed that the structures have a rather high crystalline quality and do not contain secondary-phase inclusions. X-ray photoelectron spectroscopy investigations revealed significant diffusion of Ga atoms from the GaAs regions into the InAsSb:Fe layers, which has led to the formation of an InGaAsSb:Fe compound with a Ga content up to 20 at. %. It has been found that the ferromagnetic properties of the InAsSb:Fe magnetic semiconductor improve with increasing Sb:As ratio. It has been concluded that the indirect ferromagnetic exchange interaction between Fe atoms occurs predominantly via Sb atoms.

Laser direct writing allows for the fabrication of complex structures, which is particularly advantageous in micro-optic applications. However, the increasing demand for optics quality requires the lowest optical power loss, which can occur from unwanted reflections. This research demonstrates the possibility of forming an anti-reflective coating on hybrid-polymer micro-lenses fabricated by employing laser direct writing (LDW), without changing their geometry. Such coating deposited by atomic layer deposition (ALD) decreased the reflection from 3.3 % to 0.1 % at the wavelength of 633 nm for one surface of SZ2080™.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

Serial femtosecond crystallography (SFX) using an X-ray free-electron laser (XFEL) enables determination of room-temperature structures without causing radiation damage. Using an optical pump-probe or mix-and-injection, SFX enables the intermediate state visualization of a molecular reaction. In SFX experiments, serial and stable microcrystal delivery to the X-ray interaction point is vital for reasonable data collection and efficient beam time. The Pohang Accelerator Laboratory X-ray Free Electron Laser (PAL-XFEL) facility established SFX instruments at a nanocrystallography and coherent imaging (NCI) experimental station. Various sample delivery methods, including injection, fixed-target scanning, and hybrid methods, have been developed and applied to collect XFEL diffraction data. Herein, we review the currently available sample delivery methods for SFX at the NCI experimental station at the PAL-XFEL. This article will help PAL-XFEL users access the SFX system for their experiments.

Recent developments in mid-infrared (MIR) spectroscopic ellipsometry enabled by quantum cascade lasers (QCLs) resulted in a drastic improvement in signal-to-noise ratio compared to conventional thermal emitter based instrumentation. Thus, it was possible to reduce the acquisition time for high-resolution broadband ellipsometric spectra from multiple hours to less than 1 second. This opens up new possibilities for real-time in-situ ellipsometry in polymer processing. To highlight these evolving capabilities we demonstrate the benefits of a QCL based MIR ellipsometer by investigating single and multilayered polymer films. The molecular structure and reorientation of a 2.5m thin biaxially oriented polyethylene terephtalate film is monitored during a stretching process lasting 24.5 s to illustrate the perspective of ellipsometric measurements in dynamic processes. In addition, a polyethylene/ethylene vinyl alcohol/polyethylene multilayer film is investigated at continuously varying angle of incidence ( 0∘ – 50∘) in 17.2 s, highlighting an unprecedented sample throughput for the technique of varying angle spectroscopic ellipsometry in the MIR spectral range. The obtained results underline the superior spectral and temporal resolution of QCL ellipsometry and qualify this technique as suitable method for advanced in-situ monitoring in polymer processing.

Background: Central serous chorioretinopathy (CSC) is a common macular condition characterized by detachment of the neuroretina and is a frequent cause of central vision loss in adults. Among the various therapeutic strategies, subthreshold microsecond pulsed laser (SML) treatment has become a useful option. Despite the suggested involvement of choroidal circulatory disturbances in CSC, effects of this treatment on macular microperfusion have not been fully evaluated yet. Herein, we report the impact of SML on retinal and choroidal microvascular flow using non-invasive optical coherence tomography (OCT) angiography (OCTA). Methods: In this study, CSC patients with persistent subretinal fluid (SRF) with or without secondary choroidal neovascularization (CNV) were included (referred to as pachychoroid neovasculopathy (PNV) group and CSC group, respectively). SML was conducted using a yellow (577 nm) laser with duty cycle of 10%, spot size of 200 µm and duration of 200 ms. Best corrected visual acuity (BCVA) as well as OCT and OCTA images were evaluated at baseline and 4 weeks after SML. OCTA parameters of interest included full retinal perfusion (FRP), choriocapillaris perfusion (CCP), Sattler’s layer perfusion (SLP), and Haller’s layer perfusion (HLP), which were evaluated longitudinally and compared to unaffected fellow eyes. Results: 27 affected eyes and 17 fellow eyes from 27 patients were included. Before treatment, central retinal thickness (CRT) and subfoveal choroidal thickness (SFCT) of affected eyes were significantly larger than in fellow eyes. Four weeks after SML, CRT decreased significantly, whereas perfusion parameters did not change. In subgroup analyses, the CSC group showed a significant decrease of SFCT, whereas the PNV group did not despite the decrease of CRT. Conclusion: Our results suggest that the SML may SFCT of CSC, but not of PNV patients at least within four weeks following treatment. This effect seems to be independent of the change in choroidal perfusion measured with OCTA.

Automation of forest field reference data collection has been an intensive research objective for laser scanning scientists ever since the invention of terrestrial laser scanning more than two decades ago. Recently, it has been proposed that such automated data collection providing both the tree heights and stem curves would require a combination of above-canopy UAV point clouds and terrestrial point clouds. In this study, we demonstrate that an under-canopy UAV laser scanning system utilizing a rotating laser scanner can alone provide accurate estimates of the canopy height and the stem volume for the majority of the trees in a boreal forest. To this end, we mounted a rotating laser scanner based on a Velodyne VLP-16 sensor onboard a manually piloted UAV. The UAV was commanded with the help of a live video feed from the onboard camera of the UAV. Since the system was based on a rotating laser scanner providing varying view angles, all important elements such as treetops, branches, trunks, and ground could be recorded with laser hits. In an experiment including two different forest structures, namely sparse and obstructed canopy, we showed that our system can measure the heights of individual trees with a bias of -20 cm and a standard error of 40 cm in the sparse forest and with a bias of -65 cm and a standard error of 1 m in the obstructed forest. The accuracy of the obtained tree height estimates was equivalent to airborne above-canopy UAV surveys conducted in similar forest conditions. The higher underestimation and higher inaccuracy in the obstructed site can be attributed to three trees with a height exceeding 25 m and the applied laser scanning system VLP-16 that had a limited height measurement capacity when it comes to trees taller than 25 m. Additionally, we used our system to estimate the stem volumes of individual trees with a standard error at the level of 10%. This level of error is equivalent to the error obtained when merging above-canopy UAV laser scanner data with terrestrial point cloud data. Future research is needed for testing new sensors, for implementing autonomous operation inside canopies through collision avoidance and navigation through canopies, and for developing robust methods that work also with more complex forest structure. The results show that we do not necessarily need a combination of terrestrial point clouds and point clouds collected using above-canopy UAV systems in order to accurately estimate the heights and the volumes of individual trees.

Comparison of the influence of conditioning temperature of microspheres made of medical grade poly(L-lactide) (PLLA) and polylactide with 4wt.% of D-lactide content (PLA), on its thermal and structural properties is presented. The microspheres were fabricated by solid-in-oil-in-water method for application in additive manufacturing. The microspheres were annealed below glass transition temperature (Tg), above Tg but below onset of cold crystallization, and at two temperatures selected from the range of cold crystallization corresponding to crystallization of α’ and α form of poly(L-lactide) respectively, i.e., at 40°C, 70°C, 90°C and 120°C, in order to verify the influence of conditioning temperatures on sinterability of microspheres set as sintering window (SW). Based on differential scanning calorimetry measurements SW of microspheres were evaluated with consideration of existence of cold crystallization and reorganization of crystal polymorph. The results indicate that the conditioning temperature influence on availability and range of SW that depending on the D-lactide presence. We postulate the need for an individual approach for polylactide powders in determining the SW as a temperature range free of any thermal events. Moreover, other core powder characteristic, such as residual solvent content, morphology, particle size distribution, powder flowability and thermal conductivity, as a key property for successful laser sintering, are characterized. The microspheres are close to sphere and the size of microspheres are below 100 µm. Residual solvents content decreases with the increase of annealing temperature. The thermal conductivity is 0.073 W/mK and 0.064 W/mK for PLA and PLLA microspheres, respectively, and it depends on the spherical shape of the microspheres. Furthermore, the WAXD studies prove that an increase in the conditioning temperature causes a slight increase in crystallinity degree for PLLA microspheres and clear increase in crystallization for PLA microspheres.

Barrett's esopaghagus (BE) is a known precursor of esophageal adenocarcinoma (EAC). Patients with BE undergo regular surveillance to early detect stages of EAC. Volumetric laser endomicroscopy (VLE) is a novel technology capable of imaging the inner tissue layers of the esophagus over a 6-cm length scan. However, interpretation of full VLE scans is still a challenge for human observers. In this work, we train an ensemble of deep convolutional neural networks to detect neoplasia in BE patients, using a dataset of images acquired with VLE in a multicenter study. We achieve values of AUC=$0.96$ on the unseen test dataset and we compare our results with previous work done with VLE analysis. Our method for detecting neoplasia in BE patients facilitates future advances on patient treatment and provides clinicians with new assisting solutions to process and better understand VLE data.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p &lt; 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

We study the tight focusing properties of generic bright and dark HyOPS beams in the presence of primary coma. The role of the polarization singularity index and handedness of the polarization of the HyOPS beams on the focused structure has been discussed. Results have been presented for the total intensity, component intensities, and component phase distributions for left-, and right-handed bright and dark star and lemon types singularities. The presence of primary coma distorted the focal plane intensity distributions for both positive and negative index generic C-points. Coma is known to disturb the circular symmetry of the focal plane intensity distribution. Similarly in tight focusing polarization is known to disturb the symmetry. Therefore, a beam with structured and inhomogeneous polarization distribution tightly focused under the influence of coma is a fit case to study. It is found that the presence of primary coma aberration in the focusing system produces a positional shift of the high-intensity peaks and a reduction of the intensity on one side of the center. As the strength of the primary coma increases, the focal plane intensity distributions shift more and more toward the right from the initial position. Unlike the scalar vortex case, in the case of HyOPS beams, the focal plane intensity distribution undergoes rotation, as the helicity of the HyOPS beams is inverted, in addition to shifting. All the component phase distributions are found to be embedded with phase vortices of charge ±1.

In this paper, an intelligent blind guide system based on 2D LiDAR and RGB-D camera sensing is proposed, and the system is mounted on the smart cane. The intelligent guide system relies on 2D LiDAR, RGB-D camera, IMU, GPS, Jetson nano B01, STM32 and other hardware. The main advantage of the intelligent guide system proposed by us is that the distance between the smart cane and obstacles can be measured by 2D LiDAR based on Cartographer algorithm, thus achieving Simultaneous localization and mapping (SLAM). At the same time, through the improved yolov5 algorithm, pedestrians, vehicles, pedestrian crosswalks, traffic lights, warning posts, stone piers, tactile paving and other objects in front of the visually impaired can be quickly and effectively identified. Laser SLAM and improved yolov5 obstacle identification tests were carried out inside a teaching building on the campus of Hainan Normal University and on a pedestrian crossing on Longkun South Road in Haikou City, Hainan Province. The results show that the intelligent guide system developed by us can drive the wheels and omnidirectional wheels at the bottom of the smart cane, and give the smart cane a self-leading blind guide function like a "guide dog", which can effectively guide the visually impaired to avoid obstacles and reach the predetermined destination, and can quickly and effectively identify the obstacles on the way out. The laser SLAM speed of this system is 25~31FPS, which can realize the short-distance obstacle avoidance and navigation function both in indoor and outdoor envionments. The improved yolov5 helps to identify 86 types of objects, the recognition rate for pedestrian crosswalks and for vehicles are 84.6% and 71.8%, respectively; the overall recognition rate for 86 types of objects is 61.2%, and the obstacle recognition rate of the intelligent guide system is 25-26FPS.

Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.

Over the past few years, there has been an increasing fascination with electric unmanned aerial vehicles (UAVs) because of their capacity to undertake demanding and perilous missions, while also delivering advantages in terms of flexibility, safety, and expenses. These UAVs are revolutionizing various public services, encompassing real-time surveillance, search and rescue operations, wildlife assessments, delivery services, wireless connectivity, and precise farming. To enhance their efficiency and duration, UAVs typically employ a hybrid power system. This system integrates diverse energy sources, such as fuel cells, batteries, solar cells, and supercapacitors. The selection of an appropriate hybrid power arrangement and the implementation of an effective energy management system are crucial for the successful functioning of advanced UAVs. This article specifically concentrates on UAV platforms powered by batteries, incorporating innovative technologies like in-flight recharging via laser beams and tethering. It provides an all-encompassing and evaluative examination of the current cutting-edge power supply configurations, with the objective of identifying deficiencies, presenting perspectives, and offering recommendations for future consideration in this domain.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Combining Matrix-Assisted Laser Desorption/Ionization Time-of-Flight (MALDI-TOF) spectra data and artificial intelligence (AI) has been introduced for rapid prediction on antibiotic susceptibility test (AST) of S. aureus. Based on the AI predictive probability, the cases with probabilities between low and high cut-offs are defined as “grey zone”. We aimed to investigate the underlying reasons of unconfident (grey zone) or wrong predictive AST. A total 479 S. aureus isolates were collected, analyzed by MALDI-TOF, and AST prediction, standard AST were obtained in a tertiary medical center. The predictions were categorized into the correct prediction group, wrong prediction group, and grey zone group. We analyzed the association between the predictive results and the demographic data, spectral data, and strain types. For MRSA, larger cefoxitin zone size was found in the wrong prediction group. MLST of the MRSA isolates in the grey zone group revealed that uncommon strain types composed 80%. Amid MSSA isolates in the grey zone group, the majority (60%) was composed of over 10 different strain types. In predicting AST based on MALDI-TOF AI, uncommon strains and high diversity would contribute to suboptimal predictive performance.

SLM Additive Manufacturing has demonstrated great potential for aerospace applications when structural elements of individual design and/or complex shape need to be promptly supplied. 3D-printable AlSi10Mg (RS-300) alloy is widely used for the fabrication of different structures in aerospace industry. The importance of the evaluation of residual stresses that arise as a result of complex 3D-printing process thermal history is widely discussed in literature, but systematic assessment remains lacking for their magnitude, spatial distribution, and comparative analysis of different evaluation techniques. In this study we report the results of a systematic study of residual stresses in a 3D-printed double tower shaped samples using several approaches: the contour method, blind hole drilling laser speckle interferometry, X-ray diffraction, and Xe pFIB-DIC micro-ring-core milling analysis. We show that a high level of tensile and compressive residual stresses is inherited from SLM 3D-printing and retained for longer than 6 months. The stresses vary over a significant proportion of the material yield stress. All residual stress evaluation techniques considered returned comparable values of residual stresses even regardless of dramatically different dimensional scales from millimeters for the Contour Method down, laser speckle interferometry and XRD and down to small fractions of a mm (70 μm) for Xe pFIB-DIC ring-core drilling. The use of residual stress evaluation is discussed in the context of optimizing the printing strategy to enhance the mechanical performance and long-term durability.

A pilot study on laser 3D printing of inorganic free-form micro-optics is experimentally validated. Ultrafast laser nanolithography is employed for structuring hybrid organic-inorganic material SZ2080TM followed by high-temperature calcination post-processing. The combination allows production of 3D architectures and the heat-treatment results in converting the material to inorganic substance. The produced miniature optical elements are characterized and their optical performance demonstrated. Finally, the concept is validated for manufacturing compound optical components such as stacked lenses. This is opening for new directions and applications of laser made microoptics under harsh conditions such as high intensity radiation, temperature, acidic environment, pressure variations, which include open space, astrophotonics, and remote sensing.

Keyhole laser beam welding (LBW) of stainless steel sheets with a gap in between is numerically simulated with a three-dimensional, transient multi-physical model for laser material processing. At first, the model’s ability to reproduce experimental results on a relatively coarse computational mesh within reasonable computing time, so as to serve as process optimization tool, is presented. An example of process optimization, where a given set of weld seam quality criteria is fulfilled by iteratively optimizing a secondary laser beam, is shown. The relatively coarse mesh, in combination with a good model calibration to the experimental conditions, allows for sufficiently fast simulations to use this approach for optimization tasks. Finally, using a finer spatial and temporal discretization, the dynamic processes in the vicinity of the keyhole leading to the formation of pores are investigated. The physical phenomena predicted by the simulation are coherent with experimental observations found in literature.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

This study presents an effective control algorithm to improve the robustness of fast steering mirror (FSM)-based laser beam steering systems against dynamic disturbances such as repetitive disturbances resulting from operating conditions. A stable control system must be able to maintain the required high-precision control even when dynamic disturbances affect the FSM system. In this study, an improved control method is proposed using an internal model principle (IMP)-based nonlinear controller with a disturbance observer (DOB) for the FSM system. This IMP-based controller with DOB can attenuate the residual control error signal under dynamic disturbance conditions.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

Self-phase modulation (SPM) broadening of laser spectra was studied in a transmission mode in natural and synthetic diamonds at variable laser wavelengths (515 and 1030 nm), pulse energies and widths (0.3 - 12 ps, positively chirped pulses), providing their filamentary propagation. Besides the monotonous SPM broadening of the laser spectra versus pulse energy, more pronounced for the (sub)picosecond pulsewiths and more doped natural diamond, periodical low-frequency modulation was observed in the spectra at the shorter laser pulsewidths, indicating dynamic Bragg filtering of the supercontinuum due to ultrafast plasma and nanoplasmonic effects. Damping of broadening and ultramodulation for the longer picosecond pulsewidths was related to thermalized electron-hole plasma regime established for the laser pulsewidths longer, than 2 ps. Unexpectedly, at higher pulse energies and corresponding longer microfilaments, the number of spectral modulation features increases, indicating dynamic variation of the periods in the longitudinal plasma Bragg gratings along the filaments due to prompt secondary laser-plasmon interactions.

Quantum computing arrives. Preceded by Mādhava of Sangamagrāma and other Hindu mathematicians, around 1,500 CE, and our previous work, we show at least 4 quantum properties that are indeed universal in some number systems; here we use them to enable quantum computing. Using the sets B={0,1}, B^n, N, Z, Q, and Q*, one has +4 quantum properties that one can trust, as archetypes of easy communication to friends and foes, to ignoranti or cognoscenti, and for quantum consciousness. Therefore, this work applies to computer calculations, apps in cell phones, algebra, atoms, mathematics, physics, and the human mind.

We present a new vision on the double-slit experiment (DSE), that does not use any waves or the so-called wave-particle duality. It is based on particles, viewed as localized vibrations. Rather than being illogical, or mysterious, the approach reproduces logically the interference patterns observed externally, using the well-known ``amplification of stimulated emission'' (ASE). The conservation of particle number is not observed. Different particles can present ASE with in-phase or counter-phase behavior, making the patterns observed for electrons, other particles, even atoms. The Law of the Excluded Middle (LEM) is not broken illogically in two-states macroscopically, but broken naturally in three or more states, microscopically, using ASE. Any particle supporting ASE, in-phase or counter-phase, can enter a DSE, and provide an external interference pattern. Frequency plays a role, while amplitude is not considered. This work is important in quantum computing, possibly saving cost, time, and welcoming more participants.

Additive manufacturing (AM) technologies show potential for the development of functionally integrated lightweight designs, biomimetic structures and material savings. Typically, as-built surfaces show powder particle agglomerations and re-entrant features, leading to rough surfaces, which are associated with poor fatigue performance. To benefit from the full range of advantages with special focus on aerospace applications, critical features for crack initiation when subjected to fatigue loading need to be identified and mitigated. A first step toward achieving this goal is the surface texture characterisation based on the quantification of surface features. In this paper, selected areal height, functional and feature parameters from ISO 25178-2:2022 are generated and process-specific features are examined for as-built AlSi7Mg0.6 from laser powder bed fusion (PBF-LB). A connection with the particle size distribution of the used powder is demonstrated. It is shown that surface feature analysis opens up opportunities to use physically meaningful surface characteristics in future quality assurance and part qualification processes.

Atomic state preparation can benefit from a compact and uniform magnetic field source. Simulations and experimental measurements have been used to design, build, and test such a source as shown by optical pumping of atomic Helium. This source is a 9.5 mm (3/8") OD x 6.7 mm (1/4") ID x 9.5 mm (3/8") long, NdFeB-N42 assembly of 1.6 mm (1/16") thick customized annular magnets. It has octopole decay with a residual dipole far field from imperfect dipole cancelations. It has greater than 50% clear aperture with uniform and collimated magnetic field consistent with the prediction of several models. Octopole roll-off localizes the field minimizing the need for shielding in applications. The device is applied to a high precision 3,4He laser spectroscopy experiment using σ+ or σ- optical pumping currently resulting in a measured 99.3% preparation efficiency and in accordance with a rate-equation model.

While L-PBF offers advantages in terms of geometrical freedom or lightweight construction, its use is often limited by economic constraints or currently achievable part costs. With an anticipated increase of L-PBF machine productivity during the next years, an increase of the share of material costs and the share of non-productive time for powder layer application process is to be expected. This results in a demand for less expensive powder materials and advanced processing strategies for the short-and medium-term advancement of L-PBF. As one possible approach, the processing of gas- and water atomized stainless steel (316L) powders with different morphology and particle size distribution as well as their impact on L-PBF productivity is investigated. The actual powder applicability in L-PBF systems and the L-PBF processability determines the minimum necessary powder quality. The main focus of the presented work is put on the interaction between powder quality, powder layer properties, part quality and cost-effectiveness of the L-PBF process. To this end, the influence of the gas and water-atomized powder properties (particle size and morphology) during the powder layer application process at highest possible powder recoater speeds and the resulting powder bed properties (powder layer density, powder bed density, powder demixing) and part properties (part density and tensile strength) is investigated.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

Two-photon imaging of light stimulus-evoked neuronal activity has been used to study all neuron classes in the vertebrate retina, from the photoreceptors to the retinal ganglion cells. Clearly, the ability to study retinal circuits down to the level of single synapses or zoomed out at the level of complete populations of neurons, has been a major asset in our understanding of this beautiful circuit. In this chapter, we discuss the possibilities and pitfalls of using an all-optical approach in this highly light-sensitive part of the brain.

Existing implants used with Total Knee Arthroplasty (TKA), Total Hip Arthroplasty (THA), and other joint reconstruction treatments, have displayed premature failures and frequent needs for revision surgery in recent years, particularly with young active patients who represent more than 55% of all joint reconstruction patients. Bone cement and stress shielding have been identified as the major reasons for premature joint failures. A breakdown of the cement may happen, and revision surgery may be needed because of the aseptic loosening. The significant mismatch of stiffness properties of patient trabecular bones and metallic implant materials in joint reconstruction surgery results in the stress shielding phenomenon. This could lead to significant bone resorption and increased risk of bone fracture and the aseptic loosening of implants. The present project introduces an approach for development of customized cellular structures to match the mechanical properties and architecture of human trabecular bone. It consists of four modules:1- characterization of geometry, microarchitecture, and stiffness properties of patient’s bones; 2- developing customized lattice structures tailored to mimic properties established in module 1; 3 - integration of developed lattice structure into full scale implant design and manufacturing; 4- implementation of the developed technology for use in implants that would overcome most of the issues related to aseptic loosening phenomenon. The present work aims at fulfilling the objectives of module 2 by exploring new designs of customized lattice structures and texture tailored to mimic closely patients’ bone anisotropic properties and that can incorporate an engineered biological press-fit fixation technique. The effects of various lattice design variables on mechanical performance of the structure are examined through systematic experimental plan using statistical design of experiments technique and analysis of variance method. All tested lattice designs were explored under realistic geometrical, biological, and manufacturing constraints. Of the four design factors examined in this study, strut thickness was found to have the highest percent contribution (41%) regarding the structure stiffness, followed by unit cell type, and cell size. Srut shape was found to have the lowest effect with only 11% contribution. The introduced solution offers lattice structure designs that can be adjusted to match bone stiffness distribution and promote bone ingrowth and hence eliminating the phenomenon of stress shielding while incorporating biological press-fit fixation technique.

Photophysics properties such as fluorescence quenching, and photoexcitation dynamics of bimolecular non-covalent systems consisting of cationic poly[(9,9-di(3,3’-N,N’-trimethyl-ammonium) propyl fluorenyl-2,7-diyl)-alt-co-(9,9-dioctyl-fluorenyl-2,7-diyl)] diiodide salt (PFN) and anionic graphene carboxylate (GC) have been discovered for the first time by the steady state and time-resolved femtosecond transient absorption (TA) spectroscopy with broadband capabilities. The steady-state fluorescence of PFN is quenched with high efficiency by GC acceptor. Fluorescence lifetime measurements revealed that the quenching mechanism of PFN by GC is static. Here, the quenching mechanisms are well proven by TA spectra of PFN/GC systems. For PFN/GC systems, the photo electron transfer (PET) and charge recombination (CR) processes are ultrafast (within few tens of ps) related to static interactions whereas for PFN/DCB systems the PET takes place in few hundreds ps (217.50 ps)1 suggesting diffusion-controlled PET process. In the latter case, the PFN+•-DCB-• radical ion pairs as the result of PET from the PFN to DCB are clearly resolved and they are long-lived. The slow CR process (in 30 ns time scales)1 suggest PFN+• and DCB-• may already form separated radical ion pairs through charge separation (CS) process, which recombined back to the initial state with a characteristic time constant of 30 ns. The advantage of the present positively charged polyfluorene used in this work is the control over the electrostatic interactions and electron transfers in non-covalent polyfluorene/quencher systems in DMSO solution.

Nonlinear compression of narrow-band (Δ ≈ 0.2 cm-1) 20 ns KrF laser pulses in SF6 at 10 atm and CH4 at 50 atm pressure was studied. Both SBS and SRS optically phase conjugated backward reflected radiation was registered with energy reflectivity 10−14% in SF6 and CH4. In SF6 SBS pulses gradually shortened from 10 ns to 2−3 ns with pumping decrease to the SBS threshold ~ 10 mJ, while the SRS pulse had the shortest length of 30−60 ps for the maximal pumping of 120 mJ and broadened near the SRS threshold of ~30 mJ. For the SRS pulse energy ~ 2 mJ peak power 5×107 W was tenfold higher than the pump power. The theoretical model predicted a soliton-like SRS pulse compression to a temporal length of the order of vibrational relaxation time. There was no pulse compression of backward SBS and SRS radiation in CH4, while in the forward direction SRS pulses shortened to 3−4 ns at reduced pumping.

Two pre-pulses focused at different positions and at different time moments were used to enhance THz emission generated by the main pulse. The emission of THz radiation from air breakdown regions of focused ultrashort fs-laser pulses (800 nm/35 fs) at shockwave front prepared by pre-pulses was investigated, and a 3D spatio-temporal control was established for the most intense emission. The laser pulse-induced air breakdown forms a ~120 micrometers-long focal volume and generates a shockwave that delivers denser air into the focal region of the main pulse for enhanced generation of THz radiation at 0.1-2.5 THz spectral window. The intensity of pre- and main-pulses was at the tunneling ionisation intensities (1-3)x10¹⁶ W/cm² and corresponded to sub-critical (transparent) plasma in air. Polarisation analysis revealed that the orientation of the air density gradients generated by pre-pulses and their time-space placement defined the ellipticity of the generated THz electrical field. The rotational electric current is the origin of THz radiation. The current is created by non-parallel gradients of electron density and temperature. Scaling dependencies of THz emission control are established.

Using valid experimental parameters we quantify the magnitude of resonantly phonon-driven precession of exchange magnons in freestanding ferromagnetic nickel thin films on their thickness L. Analytical solutions of acoustically driven equations for magnon oscillators display a nonmonotonous dependence of the peak magnetization precession on the film thickness. It is explained by different L-dependence of multiple prefactors entering in the expression for the total magnetization dynamics. Depending on the ratio of acoustic and magnetic (Gilbert) damping constants, the magnetization precession is shown to be amplified by a Q-factor of either the phonon or the magnon resonance. The increase of the phonon mode amplitude for thinner membranes is also found to be significant. Focusing on the magnetization dynamics excited by the two first acoustic eigenmodes with p=1 and p=2 we predict the optimum thicknesses of nickel membranes to achieve large amplitude magnetization precession at multi 100 GHz frequencies at reasonably low values of an external magnetic field.

We find at least 4 quantum properties that are indeed universal in some number systems; and we can use them for quantum consciousness. Using the sets B={0,1}, N, Z, or Q has the +4 quantum properties that one can trust, as archetypes of easy communication to friends and foes, to ignoranti or cognoscenti, and for quantum computing. This paper proposes the use of Bayesian geometry to reduce the space of possible results, reducing or increasing initial beliefs by successive experimentation. This is exemplified in biology and mathematics, and can be applied to physics and other sciences. The conclusion is that an experimental fact can be absolutely verified. Any mathematical choice (as verified by computers) militating against R=Q, is under an absolutely low chance to succeed. Infinitesimals are denied based on 3^16 independent factors. This is not a probabilistic result, but based on reduction of the Bayes geometry for updating beliefs. This work applies to non-probabilistic and unknown phenomena, such as those found in oscillations (neutrino, health), evolution, and quantum computing, denies Gödel's uncertainty, and solves the liar's paradox by reflection. This connects different scientific fields with one another, in an internet, i.e., in a network of connections of multiple open networks, using the set Q, resembling a hologram, and includes entanglement.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

This is a review on social laser theory completed with its new developments and applications. An important methodological step towards similarity with quantum physics is the invention and consistent operation with infons. These are excitations of the quantum social-information field carrying social energy and coarse grained content of communications (their color and quasi-color). We study in more detail interactions of infons with social atoms, the processes of absorption and emission (spontaneous and stimulated). We also analyze the dynamics of iterations of the cascades of infons in the social resonators. The latter are based on social networks coupled to laser's gain medium composed of social atoms. Consideration of the pro-war and pro-peace beams leads to the general discussion on the competing beams of social radiation and the conditions for their creation and coexistence. The role of social networks in lasing is illustrated by the protests during the COVID-19 pandemic. It is highlighted that a human gain medium can approach the state of population inversion with supply of infons of one sort (quasi-color), but the stimulated emission can be induced by injection into the gain medium of infons of a different quasi-color. We call this behavior of social atoms memorylessness. This theoretical property is illustrated with the examples from the modern social-political life.

The interaction of electrons with strong laser fields is usually treated with semiclassical theory, where the laser is represented by an external field. There are analytic solutions for the free electron wave functions, which incorporate the interaction with the laser field exactly, but the joint effect of the atomic binding potential presents an obstacle for the analysis. Moreover, the radiation is a dynamical system, the number of photons changes during the interactions. Thus, it is legitimate to ask how can one treat the high order processes nonperturbatively, in such a way that the electron-atom interaction and the quantized nature of radiation be simultaneously taken into account? An analytic method is proposed to answer this question in the framework of nonrelativistic quantum electrodynamics. As an application, a quantum optical generalization of the strong-field Kramers-Heisenberg formula is derived for describing high-harmonic generation. Our formalism is suitable to analyse, among various quantal effects, the possible role of arbitrary photon statistics of the incoming field. The present paper is dedicated to the memory of Prof. Dr. Fritz Ehlotzky, who had significantly contributed to the theory of strong-field phenomena over many decades.

Drought-induced plant mortality has increased globally during the last decades and is forecasted to influence global vegetation dynamics. Timely information on plant water dynamics is essential for understanding and anticipating drought-induced plant mortality. The most common metric that has been used for decades for measuring water stress is leaf water potential (Ψ_L), which is measured destructively. To obtain information on water dynamics from trees and forested landscapes, remote sensing methods have been developed. However, the spatial and temporal resolution of the existing methods have limited our understanding of water dynamics and diurnal variation of Ψ_L within single trees. Thus, we investigated the capability of terrestrial laser scanning (TLS) intensity in observing diurnal variation in Ψ_L during a 50 hour monitoring period and aimed to improve understanding on how large part of the diurnal variation in Ψ_L can be captured using intensity observations. We found that TLS intensity at 905 nm wavelength was able to explain 78% of the variation in Ψ_L for three trees of two tree species with a root-mean square error of 0.137 MPa. Based on our experiment with three trees, time-series of TLS intensity measurements can be used in detecting changes in Ψ_L, and thus it is worthwhile to expand the investigations to cover a wider range of tree species and forests and further increase our understanding of plant water dynamics at wider spatial and temporal scales.

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

Laser-induced breakdown spectroscopy (LIBS) of pharmaceutical drugs that contain paracetamol is investigated in air and argon atmospheres. Characteristic neutral and ionic spectral lines of various elements and molecular signatures of CN violet and C₂ Swan band systems are observed. The relative hardness of all drug samples is measured as well. Principal component analysis, a multivariate method, is applied in data analysis for demarcation purposes of the drug samples. The CN violet and C₂ Swan spectral radiances are investigated for evaluation of possible correlation of the chemical and molecular structures of the pharmaceuticals. Complementary Raman and Fourier-transform-infra-red spectroscopies are used record molecular spectra of the drug samples. The applicationof the above techniques for the drug screening are important for identification and mitigation of drugs that reveal additives that may cause adverse side-effects.

One of the most important pieces of equipment used in labs in culturing populations of fruit flies (Drosophila sp.) is that of the “CO₂ gas plate”, which is used to anesthesize individuals during “fly-pushing”. This piece of equipment consists of a box with a porous top into which carbon-dioxide is pumped. Flies placed on its surface are left immobilized, permitting the sorting, categorizing and/or counting of flies during population culturing and experimental assays. Unfortunately, commercially available gas plates are typically expensive. Here, we describe a new design for a gas plate that can be easily produced using a 3D printer and a laser cutter, which we are making freely available to the fly community.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

Candidiasis is one of the global public health problems. In fluconazole resistant Candida spp. (FRCS), mutations in ergosterol biosynthesis gene 11 (ERG 11) have been commonly found. This study aimed to determine the profile of FRCS isolates and to detect mutations in part of ERG 11 gene in fluconazole resistant Candida albicans (FRCA) isolates. Study was conducted on 150 isolates of FRCS obtained from patients admitted in a tertiary care hospital, South India from September 2019 to December 2021. Candida spp. was identified by MALDI-TOF MS and fluconazole resistance was detected by VITEK 2 system. Following which a part of the ERG 11 gene of the FRCA isolates were amplified, purified, sequenced and a phylogenetic tree was constructed. Out of the 150 FRCS, the most common FRCS was C. auris followed by C. glabrata, C. krusei, C. parapsilosis, C. albicans, C. tropicalis and C. guilliermondii. Sequencing of amplicons detected a single missense mutation and 44 silent mutations. We opined that fluconazole resistance in FRCA isolates may be due to mecha-nisms other than the studied one in our region. Phylogenetic analysis of amplified sequences of 12 FRCA isolates observed three clusters and all 12 sequences showed relatedness to Malaysian 2019 isolates.

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

With increasing power and speed of laser welding, in-process monitoring has become even more crucial to ensure process stability and weld quality. Due to its low cost and installation flexibility, acoustic process monitoring is a promising method and has demonstrated its effectiveness. Since its feasibility has been the focus of existing studies, the temporal resolution of acoustic emissions (AE) has not yet been addressed despite its utmost importance for realizing real-time systems. Aiming to provide a benchmark for further development, this study investigates the relationship between duration and informativeness of AE signals during high power (3.5kW) and high speed (12m/min) laser beam butt welding. Specifically, the informativeness of AE signals is evaluated based on the accuracy of detecting and quantifying joint gaps for various time windows of signals, yielding numerical comparison. The obtained results show that signals can be shortened up to a certain point without sacrificing their informativeness, encouraging to optimize the signal duration. Our results also suggest that large gaps (> 0.3mm) induce unique signal characteristics in AE, which are clearly identifiable from 1 ms signal segments, equivalent to 0.2mm weld seam.

This work communicates the connection of measured shadowgraphs from optically induced air breakdown with emission spectroscopy in selected gas mixtures. Laser-induced optical breakdown is generated using 850 mJ and 170 mJ, 6-ns pulses at a wavelength of 1064 nm, the shadowgraphs are recorded using time-delayed 5-ns pulses at a wavelength of 532 nm and a digital camera, and emission spectra are recorded for typically a dozen of discrete time-delays from optical breakdown by employing an intensified charge-coupled device. The symmetry of the breakdown event can be viewed as close-to spherical symmetry for time-delays of several 100 ns. Spectroscopic analysis explores well-above hypersonic expansion dynamics using primarily the diatomic molecule cyanide and atomic hydrogen emission spectroscopy. Analysis of the air breakdown and selected gas breakdown events permits the use of Abel inversion for inference of the expanding species distribution. Typically, species are prevalent at higher density near the hypersonically expanding shockwave, measured by tracing cyanide and a specific carbon atomic line. Overall, recorded air breakdown shadowgraphs are indicative of laser-plasma expansion in selected gas mixtures, and optical spectroscopy delivers analytical insight into plasma expansion phenomena.

We put forward a co-axial pump(optical)-probe(X-rays) experimental concept and show performance of the optical component. A Bessel beam generator with a central 100 micrometers-diameter hole (on the optical axis) was fabricated using femtosecond (fs) laser structuring inside a silica plate. This flat-axicon optical element produces a needle-like axial intensity distribution which can be used for the optical pump pulse. The fs-X-ray free electron laser (X-FEL) beam of sub-1 micrometer diameter can be introduced through the central hole along the optical axis onto a target as a probe. Different realisations of optical pump are discussed. Such optical elements facilitate alignment of ultra-short fs-pulses in space and time and can be used in light-matter interaction experiments at extreme energy densities on the surface and in the volume of targets. Full advantage of ultra-short 10 fs X-FEL probe pulses with fs-pump(optical) opens an unexplored temporal dimension of phase transitions and the fastest laser-induced rates of material heating and quenching. A wider field of applications of fs-laser-enabled structuring of materials and design of specific optical elements for astrophotonics is presented.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

This study aimed to evaluate the proliferation and migration of fibroblast cells derived from chronic wounds and investigate the impact of low-level laser therapy (LLLT) on their growth and migration. A total of 60 dermal samples were obtained from three sites of chronic pressure ulcers and diabetic ulcers in 20 patients. Following collection in the operating room, the dermal samples were isolated using the procedure described by Freshney RI. Fibroblasts from the wound base (Site 1) exhibited a slow proliferation rate and a decrease in proliferative capacity. Fibroblasts from wound margins (Site 2) and adjacent healing skin (Site 3) could be successfully isolated and maintained for multiple generations without any morphological changes. Fibroblasts from chronic wounds at Sites 2 and 3 showed slower proliferation rates and reduced migration capabilities compared to normal dermal fibroblasts (control samples). The fibroblast cells were exposed to LLLT at different energy levels (2.5, 3, and 3.5 J/cm2). The laser-treated groups demonstrated a significantly higher increase in cell count compared to the control sample, with the highest increase observed at an energy level of 3 J/cm2. These findings suggest that LLLT at an energy level of 3 J/cm2 could effectively enhance fibroblast migration, indicating its potential as a therapeutic intervention for chronic wounds.

The use of analytical techniques is important and critical in all areas of REE research such as exploration, mining, extraction, and metallurgical activities at different stages. At every stage of these activities, rock, ore, mineral, and other related materials have to be analysed for their REE contents in terms of elemental, isotopic, and mineralogical concentrations using different analytical techniques. Spectacular developments have taken place in the area of analytical instrumentations during the last four decades, with some of them having shrunk in size and become hand-held. Among laboratory-based techniques, F-AAS, GF-AAS, ICP-OES, and MP-AES have become very popular. Because of high sensitivity, less interference effects, and ease of use. ICP-MS techniques such as quadrupole-ICP-MS, ICP-MS/MS, ICP-TOF-MS, MH-ICP-MS, HR-ICP-MS, and MC-ICP-MS, with both solution nebulisation as well as direct solid analysis using laser ablation sample introduction methods, have become extremely popular for REE analysis. For direct analysis of solids INAA, XRF, and LIBS techniques besides LA-based ICP-MS techniques are being extensively utilised. LIBS technique in particular requires little to no sample preparation. TIMS, SIMS, and SHRIMP techniques are being used for isotopic as well as dating REE depots. Portable analytical techniques such as pXRF, pLIBS, and Raman spectrometers are able to do in situ analysis even in the field helping to take fast decisions during exploration studies. At present hyperspectral remote sensing techniques including hand-held, drone, and satellite-based techniques have become very popular in REE exploration studies because of their ability to cover larger areas in a limited time and thus became very cost-effective. Deployment of microanalytical devices/sensors mounted in remotely operated vehicles (ROV) is being successfully utilized in detecting REE-rich deposits in the deep oceans. Providing updated in-depth information on all these important aspects with suitable examples, especially from the point of view of REE research studies is the focal point of this review article.

The broad acceptance of electromobility depends heavily on the performance and service life of the battery technology used. Lithium-ion battery technology is currently the most promising energy storage technology for mobile applications, but the performance and capacity of the cells is extremely temperature sensitive. Especially in these new complex and powerful applications there is a significant need for thermal management. Depending on the ambient conditions, part of the effective battery energy must therefore be used to temper the system. So far, mainly active components have been used for this task. This not only reduces the overall efficiency, but also increases the weight, volume and maintenance requirements of the system. In the present work, an alternative battery temperature management system (BTMS) was developed. A concept based on latent heat storage materials was created, which uses the advantages of thermal energy storage and the design freedom of additive manufacturing technology, and its suitability for use in battery applications was checked. On the one hand, the use of systems for storing thermal energy was researched and, on the other hand, an innovative cooling concept was created considering new production possibilities.

Visible light communication (VLC) can offer the advantages of license and electromagnetic interference (EMI) free wireless transmission. As optical signal does not interference with the radio-frequency (RF) signal, VLC can be used to augment RF wireless communication to provide extra communication capacity while without degrading the performance of both signals. In order to achieve high performance VLC transmission, optical alignment between the optical transmit (Tx) and receiver (Rx) is very critical to enhance the received signal-to-noise ratio (SNR). Optical beam-steering at the Tx can be utilized to ensure narrow optical beam can reach the Rx; however, complicated and active tracking are required. Lenses or compound parabolic concentrators (CPCs) can be install in front of the Rx for focusing to enhance the SNR. However, these will limit the Rx field-of-view (FOV) and making the VLC transmission more subjected to misalignment issue. Hence, many creative optical antennas have been proposed and demonstrated using special optical materials as well as special Rx to enhance the FOV of VLC systems. However, they have their limitations, such as data rates and FOVs. In this work, we put forward and demonstrate a bi-direction free-space VLC system supporting multiple moveable Rxs using a light-diffusing optical fiber (LDOF). The downlink (DL) signal is launched from an head-end or central office (CO) far away to the LDOF at the client side via a free-space transmission. When the DL signal is launched to the LDOF, which acts as an optical antenna to re-transmit the DL signal to different moveable Rxs. The uplink (UL) signal is sent via the LDOF towards the CO. In a proof-of-concept demonstration, the LDOF is 100 cm long and the free space VLC transmission between the CO and the LDOF is 100 cm. 210 Mbit/s DL and 850 Mbit/s UL transmissions, meeting the pre-forward-error-correction bit error rate (pre-FEC BER = 3.8 × 10−3) threshold are achieved.

This work investigates spatial and temporal distributions of hydroxyl, OH, in laser-plasma in laboratory air at standard ambient temperature and pressure. Of interest are determination of temperature and density of OH and establishment of a correlation of molecular OH emission spectra with shadow graphs for time delays of 50 to 100 microsecond, analogous to previous work on shadow graph and emission spectroscopy correlation for cynaide, CN, in gas mixtures and for time delays of the order of 1 microsecond. Wavelength- and sensitivity- corrected spatiotemporal data analysis focuses on temperature inferences using molecular OH emission spectroscopy. Near-ir radiation from a Q-switched laser device initiates optical breakdown in laboratory air. The laser device provides 6 nanosecond, up to 850 milli Joule pulses at a wavelength of 1064 nanometer, and focal irradiance in the range of 1 to 10 Tera Watt per centimeter-squared. Frequency doubled beams are utilized for capturing shadow graphs for visualization of the breakdown kernel at time delays in the range of 0.1 to 100 microsecond. OH emission spectra of the laser plasma, spatially resolved along the slit dimension, are recorded in the wavelength range of 298 nm to 321 nm, and with gate widths adjusted to 10 microsecond for the intensified charge-coupled device that is mounted at the exit plane of a 0.64 m Czerny-Turner configuration spectrometer. Diatomic OH signals occur due to recombination of the plasma and are clearly distinguishable for time delays larger than 50 microsecond, but are masked by spectra of N2 early in the plasma decay.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

Ti64 alloy plays a significant role in the biomedical applications such as bioimplants for its excellent biocompatibility. Its usage can be further extended by improving the surface hardness and wear resistance. In this respect, laser surface glazing (LSG), an advanced surface modification technique, is very useful which can produce thin hardened surface layer and strong metallurgical bonding. Investigation of temporal and spatial temperature distributions of laser glazed surface of materials are essential because temperature plays significant role in achieving required surface properties. Therefore, in this study, a 3D Finite element analysis has been developed to perform transient thermal analysis of LSG for Ti64 alloy. The model investigated temperature distribution, depth of modified zone and heating and cooling. The results show that the peak temperature is attained 2095 K for 300 W laser power, 0.2 mm beam width and 0.15 ms residence time. Since this temperature is above the melting point (1933 K) of Ti64 alloy, the melt depth is calculated 22.5 μm. Furthermore, from the simulation results, the average heating and cooling rates are estimated 1.19×10⁷ Ks^-1 and 2.71×10⁶ Ks^-1 respectively which indicate the presence of hard phases in the modified zone.

In this article, we combine datasets from multiple research projects and remote sensing tech-nologies to evaluate the conservation conditions of La Fortaleza de Kuelap, a pre-Hispanic monument in Peru’s northeastern Andes that suffered significant damage during historically high seasonal rains in April 2022. Our analyses seek to identify the main causes of the collapse and locate places where the monument is likely at risk of further deterioration. To do so, we model surface hydrology using a digital elevation model (DEM) derived from drone LiDAR data, re-construct a history of previous collapses, and calculate the volume of the most recent by fusing terrestrial LiDAR and photogrammetric datasets. In addition, we examine subsurface water ac-cumulation through electrical resistivity data, reconstruct the stratification of the monument from seismic refraction data, and analyze vegetation loss and ground moisture accumulation using high resolution satellite imagery. Our results point to water accumulation as the most significant source of risk for La Fortaleza’s perimeter walls. Combined with adverse contemporary conser-vation interventions and natural conditions, this led to the collapse of April 2022. This integration of analytical results demonstrates how multi-scalar and multi-instrumental approaches provide comprehensive and timely assessments of conservation needs.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

The fusion of surface-modified steel with tungsten carbide (WC) and NiCrBSi powder through laser metal deposition has emerged as a formidable strategy for fortifying components against wear and corrosion in extreme operating environments. Meticulous selection of WC content, innovative pre-alloying techniques, and precise control of laser metal deposition profoundly influence the mechanical properties and microstructural evolution of WC-NiCrBSi coatings applied to surface-enriched commercial alloy steel (805M2, 832M13, and 827M40). These tailored coatings exhibit exceptional resilience, ideal for harsh industrial settings in Oil and gas drilling, petrochemical, and Mining sectors. Advanced materials testing techniques, including scanning electron microscopy, light optical microscopies, and microhardness testing, unveil the innate hardness attributes, with findings highlighting the unassailable fortitude of the Mixed matrix layer's side face. The amalgamation of these testing methodologies with laser metal deposition promises an unparalleled path to extend the operational lifespan of critical components in challenging working conditions. The research horizon for WC-NiCrBSi coatings remains broad, with the potential to enhance durability, operational efficiency, and cost-effectiveness across diverse applications.

Age-related macular degeneration (AMD) is a leading cause of blindness worldwide. In late-stage AMD, geographic atrophy (GA) of dry AMD or choroidal neovascularization (CNV) of neovascular AMD results in macular atrophy (MA), leading to significant visual loss. Despite the development of innovative therapies, there are currently no established effective treatments for MA. As a result, early detection of MA is critical in identifying later central macular involvement throughout time. Accurate and early diagnosis is achieved through a combination of clinical examination and imaging techniques. Our review of the literature depicted advances in retinal imaging to identify biomarkers of progression and risk factors for late AMD. Imaging methods like fundus autofluorescence (FAF), near-infrared reflectance (NIR), widefield imaging, optical coherence tomography (OCT), multicolor confocal scanning laser ophthalmoscopy (cSLO), and optical coherence tomography angiography (OCTA) can be used to detect and monitor the progression of retinal atrophy. Multifocal electroretinogram (ERG) and microperimetry are methods for quantifying visual function to map disease progression. The evolving diverse imaging modalities optimize detection of pathology anatomy and measurement of visual function; they may also contribute to the understanding of the underlying mechanistic pathways, particularly the underlying MA changes in late AMD.

This study aimed to explore the feasibility of using airborne acoustic emission in laser beam butt welding for the development of an automated classification system based on neural networks. The focus was on monitoring the formation of joint gaps during the welding process. To simulate various sizes of butt joint gaps, controlled welding experiments were conducted, and the emitted acoustic signals were captured using audible to ultrasonic microphones. To implement an automated monitoring system, a method based on short-time Fourier transformation was developed to extract audio features, and a convolutional neural network architecture with data augmentation was utilized. The results demonstrated that this non-destructive and non-invasive approach was highly effective in detecting joint gap formations, achieving an accuracy of 98%. Furthermore, the system exhibited promising potential for low latency monitoring of the welding process. The classification accuracy for various gap sizes reached up to 90%, providing valuable insights for characterizing and categorizing joint gaps accurately. Additionally, increasing the quantity of training data with quality annotations could potentially improve the classifier model's performance further. This suggests that there is room for future enhancements in the study.

Historically, the evaluation and assessment of the clinical response to treatment for canine back pain is subjective and relies on owner and clinician assessment of pain. This study evaluated the use of sequential infrared thermal images as a measure of the response of canine patients with back pain to a prescribed series of photobiomodulation therapy (PBMT) treatments. Qualifying participants had histories of pain and dysfunction associated with spinal osteoarthritis or intervertebral disk disease, or of non-specific uni- or bilateral back pain along the paravertebral epaxial muscles. Each patient was initially thermally imaged prior to PBMT treatment and then received multiple PBMT treatments delivered to the appropriate spinal area on days 1, 2, 3, and 4. Participants were reimaged on day 7. Thermal images provided an objective measure of superficial temperature changes over the area of PBMT treatment of each patient after the PBMT regimen. The temperature correlated with statistically significant changes in Colorado State University Canine Chronic Pain Scale scoring (CPS) and owner assessment using the Canine Brief Pain Inventory (CBPI), which includes a Pain Severity Score (PSS) and Pain Interference Score (PIS). The correlation of objective thermal imaging data with more subjective outcome measures suggests thermal imaging may be a valuable additional tool in monitoring therapy outcome.

The topic of this paper is the airborne evaluation of ICESat-2 Advanced Topographic Laser Altimeter System (ATLAS) measurement capabilities and surface-height-determination over crevassed glacial terrain, with a focus on the geodetical accuracy of geophysical data collected from a helicopter. To obtain surface heights over crevassed and otherwise complex ice surface, ICESat-2 data are analyzed using the density-dimension algorithm for ice surfaces (DDA-ice), which yields surface heights at the nominal 0.7~m along-track spacing of ATLAS data. As the result of an ongoing surge, Negribreen, Svalbard, provided an ideal situation for the validation objectives in 2018 and 2019, because many different crevasse types and morphologically complex ice surfaces existed in close proximity. Airborne geophysical data, including laser altimeter data (profilometer data at 905~nm frequency), differential Global Positioning System (GPS), Inertial Measurement Unit (IMU) data, on-board-time-lapse imagery and photographs, were collected during two campaigns in summers of 2018 and 2019. Airborne experiment setup, geodetical correction and data processing steps are described here. To date, there is relatively little knowledge of the geodetical accuracy that can be obtained from kinematic data collection from a helicopter. Our study finds that (1)~Kinematic GPS data collection with correction in post-processing yields higher accuracies than Real-Time-Kinematic (RTK) data collection. (2)~Processing of only the rover data using the Natural Resources Canada Spatial Reference System Precise Point Positioning (CSRS-PPP) software is sufficiently accurate for the sub-satellite validation purpose. (3)~Distances between ICESat-2 ground tracks and airborne ground tracks were generally better than 25~m, while distance between predicted and actual ICESat-2 ground track was on the order of 9~m, which allows direct comparison of ice-surface heights and spatial statistical characteristics of crevasses from the satellite and airborne measurements. (4)~The Lasertech Universal Laser System (ULS), operated at up to 300~m above ground level, yields full return frequency (400~Hz) and 0.06-0.08~m on-ice along-track spacing of height measurements. (5)~Cross-over differences of airborne laser altimeter data are 0.1918 $\pm$ 2.385~m along straight paths over generally crevassed terrain, which implies a precision of approximately 2.4~m for ICESat-2 validation experiments. (6)~In summary, the comparatively light-weight experiment setup of a suite of small survey equipment mounted on a Eurocopter (Helicopter AS-350) and kinematic GPS data analyzed in post-processing using CSRS-PPP leads to high accuracy repeats of the ICESat-2 tracks. The technical results (1)-(6) indicate that direct comparison of ice-surface heights and crevasse depths from the ICESat-2 and airborne laser altimeter data is warranted. The final result of the validation is that ICESat-2 ATLAS data, analyzed with the DDA-ice, facilitate surface-height determination over crevassed terrain, in good agreement with airborne data, including spatial characteristics, such as surface roughness, crevasse spacing and depth, which are key informants on the deformation and dynamics of a glacier during surge.

The selection equation (replicator equation) has been independently discovered not only in various fields of biology (population genetics, ecology, prebiotic evolution, and sociobiology), but also in laser theory, where it accounts for the emergence of coherent light. Selection theory (replicator dynamics) is an ensemble theory, i. e., it describes the entire system rather than individual events, neglecting details in favor of a statistical view. However, the underlying processes at the individual level are well known in biology. For light quanta, this is not the case, because quantum theory says nothing about individual events. In the Copenhagen interpretation even the existence of causality on "quantum level" is denied. A large number of recent publications, however, makes this interpretation seem questionable.In the present paper, therefore, an attempt is made to describe the basic interactions between light and matter, as far as they are relevant for the emergence of coherent light in the laser (a photon pair interaction mediated by matter is postulated), and to apply replicator dynamics on this basis. Starting point are papers of A. Einstein about the interaction of light and matter as well as the photoelectric effect. Both theories are slightly modified. Furthermore, the double-slit experiment is investigated and finally the emergence of coherent light by density-dependent selection of photons of different phase in a laser-like model. The relationship between “mean fitness”, information content of the photon ensemble and the amplitude of the light is also analyzed.

Heel pain in the “funnel-shaped” space between the calcaneus, talus, and talocalcaneonavicular and subtalar joints may be representative of Sinus Tarsi syndrome. The pain is often characterized by a burning, numbness, or tingling sensation that can stem from strains and tears on the ligaments in that area. Injury treatment typically includes balance training, muscle exercises, bracing, foot orthosis, and non-steroidal anti-inflammatory drugs (NSAIDs). This study presents Wharton Jelly (WJ) tissue allografts as an alternative intervention for patients who fail standard-care treatments. WJ targets tissue defects, unlike other therapies, which aim to reduce swelling and symptomatic pain. This study includes five female patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. After an average of 80 days, the cohort had an overall 85.29% improvement in pain. The study's limitations include a small cohort size and a non-blinded design. Given the significant improvement in pain, WJ tissue allograft, combined with other techniques, presents an optimal patient care plan for tissue defects associated with Sinus Tarsi syndrome when standard-of-care treatments fail. These results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

In synthetic diamond plate, the intrapulse correlated dynamics of self-phase modulation and spontaneous Raman scattering by optical phonons were for the first time directly investigated for tightly focused (focusing numerical aperture NA = 0.25) positively-chirped visible-range ultrashort laser pulses with variable durations (0.3-9.5 ps) and energies, transmitted through the sample. The observed modulation of the transmitted light spectra and Stokes Raman scattering spectra for the different pulse durations were related to nonthermal excitation of nonlinear phonon polarization and its eventual picosecond-scale suppression due to thermal decay of optical phonons on the timescale of electron-phonon thermalization in the material.

In this paper a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy is proposed. The functionality of this new technique we explored by detailed gas dynamic and Monte Carlo atom-trajectory simulations, which results are presented and discussed. The results of similar computer simulations for JetRIS setup (as a typical representative of the conventional nowadays in-gas-jet technique) are presented and discussed as well. The direct comparison of calculation results for proposed new technique with the conventional one shows that the double-nozzle technique has many advantages compared with that one used in the JetRIS setup at GSI for future high-resolution laser spectroscopic study of heaviest elements. To fully implement the proposed new technique to all existing (or under construction) setups for in-gas-jet laser resonance ionization spectroscopy, it will be enough just replace the used their supersonic nozzle by the miniature double-nozzle device described in the paper.

More than 700 thousand human deaths from mosquito bites are observed annually in the world. It is more than 2 times the number of annual murders in the world. In this regard, the invention of new more effective methods of protection against mosquitoes is necessary. In this article for the first time, comprehensive studies of mosquito neutralization using machine vision and a 1 W power laser are considered. Developed laser installation with Raspberry Pi that changing the direction of the laser with a galvanometer. We developed a program for mosquito tracking in real. The possibility of using deep neural networks, Haar cascades, machine learning for mosquito recognition was considered. We considered in detail the classification problems of mosquitoes in images. A recommendation is given for the implementation of this device based on a microcontroller for subsequent use as part of an unmanned aerial vehicle. Any harmful insects in the fields can be used as objects for control.