The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

Current microbiological methods for pneumonia diagnosis require invasive specimen collection and time-consuming analytical procedures. There is a need for less invasive and faster methods to detect lower respiratory tract infection. The analysis of volatile metabolites excreted by pathogenic microorganisms provides the basis for developing such a method. Given the synergistic role of Candida albicans in increasing the virulence of pathogenic bacteria causing pneumonia and the cross-kingdom metabolic interactions between microorganisms, we compare the emission of volatiles from Candida albicans yeasts and the bacteria Staphylococcus aureus using single and mixed co-cultures and apply that knowledge to human in vivo investigations. Gas-chromatography-mass spectrometry (GC-MS) analysis resulted in the identification of sixty-eight volatiles that were found to have significantly different levels in cultures compared to reference medium samples. Certain volatiles found in co-culture originated mainly from C. albicans metabolism (e.g., isobutyl acetate), whereas other volatiles primarily came from S. aureus (e.g., ethyl 2-methylbutyrate). Isopentyl valerate reflects synergic interactions of both microbes, as its level in co-cultures was found to be approximately three times higher than the sum of its amounts in monocultures. Hydrophilic-lipophilic balanced (HLB) coated meshes for thin-film microextraction (TFME) were used to pre-concentrate volatiles directly from bronchoalveolar lavage (BAL) specimens collected from patients suffering from ventilation-associated pneumonia (VAP) that was caused explicitly by C. albicans and S. aureus. GC-MS analyses confirmed the existence of in vitro-elucidated microbial VOCs in human specimens. Significant differences in BAL-extracted amounts respective to the pathogen causing pneumonia were found. The model in vitro experiments provided evidence that cross-kingdom interactions between pathogenic microorganisms affect the synthesis of the volatile compounds. The TFME meshes coated with HLB particles proved to be suitable for extracting VOCs from human material, enabling the translation of in vitro experiments on the microbial volatilome to the in vivo situation involving infected patients. This indicates the direction that should be taken for further clinical studies on VAP diagnosis based on volatile analysis.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

NiV2O6 thin films were grown on glass slides with varying thicknesses using the nebulizer spray pyrolysis. The impact of thickness on the thin films' optical, structural, morphological, and electrical characteristics was systematically investigated. The X-ray diffraction and micro-Raman analysis confirmed the formation of the triclinic NiV2O6 system. Surface morphology and roughness variations in the as-deposited NiV2O6 films were studied using scanning electron microscopy (SEM) and a profilometer. Optical properties, including optical band gap (Eg), extinction coefficient (k), absorption coefficient (α), and refractive index (n), were determined through optical reflectance and transmittance measurements. The optical energy gap of the as-deposited NiV2O6 films decreased from 2.3 eV to 1.9 eV with increased layer thickness. Furthermore, the photo-detectivity of the films demonstrated an enhancement corresponding to the prolonged spray time. The sensitivity values obtained for visible irradiation are 328, 511, and 433 for samples S1, S2, and S3, respectively. The obtained results are imputed to the specific porous microstructure.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

This work is devoted to consideration and analysis of the application of molecular dynamics simulation (MDS) methods to the study of nanosized polymer polyvinylidene fluoride (PVDF) thin ferroelectric films (two-dimensional ferroelectrics) and their composites with graphene layers: 1) to study and calculations of the polarization switching time depending on the electric field and PVDF film thickness; 2) to study and calculations of the polarization switching time depending changes of the PVDF on PVDF-TrFE film; 3) to study the polarization switching time in PVDF under influence of graphene layers. All calculations at each MDS step were carried out using quantum semi-empirical methods PM3. A comparison and analysis of the results of these calculations and the kinetics of polarization switching within the framework of the Landau-Ginzburg-Devonshire theory for homogeneous switching in ferroelectric polymer films is carried out. The study of the composite heterostructures of the “graphene-PVDF” type and calculations of their polarization switching times were presented too. It is shown that replacing PVDF with PVDF-TrFE significantly changes the polarization switching times in these thin polymer films, and that introducing various graphene layers into the PVDF layered structure leads to both an increase and a decrease in the polarization switching time. Here everything also depends on the position and displacement of the ferroelectric coercive field depending on the system damping parameters.

Gallium oxide (Ga2O3) is an emerging wide bandgap semiconductor promising a wide range of important applications. However, mass production of high-quality crystalline Ga2O3 still suffers from limitations associated with poor reproducibility and low efficiency. Low-temperature grown amorphous Ga2O3 demonstrates comparable performance with its crystalline counterparts. Lanthanide Er3+-doped Ga2O3 (Ga2O3: Er) possesses great potential for developing light-emitting devices, photodetectors and optical waveguides. The host circumstance can exert a crystal field around the lanthanide dopants and strongly influence their photoluminescence properties. Here we present a systematical study of the impact of amorphous-to-crystalline transition on the upconversion photoluminescence in Ga2O3: Er thin films. Through controlling the growth temperature of Ga2O3: Er films, the upconversion luminescence of as-grown thin films are strongly enhanced over 100 times. Moreover, the variation of photoluminescence reflects the amorphous-to-crystalline transformation of the Ga2O3: Er thin films. These results will aid further design of favorable optoelectronic devices integrated with lanthanide-doped Ga2O3 thin films.

Experimental tests and numerical analyses were carried out on short, thin-walled channel columns with modified cross-sectional shape. The columns were loaded with an axial compressive force applied at the center of gravity of the cross section. Tests were carried out on a universal testing machine, while numerical analyses were performed in ANSYS software. The purpose of the tests was to determine the values of critical forces for the compressed columns and to determine the values of maximum forces at which failure of the columns occurs. Critical forces were determined based on the strain-averaged method. Based on the study, it was found that the strength and resistance to loss of stability of columns is primarily affected by their stiffness, and therefore by the shape of the cross-sections. In addition, for short columns, it seems more important to determine the value of maximum forces than the values of critical forces.

The article describes machine learning using artificial neural networks (ANN) to develop the parameters of the friction stir welding (FSW) process for three types of aluminum joints (EN AW 7075). A total of 608 experimental data were used to build the ANN. Two types of networks were built: the first one was used to classify good/bad connections with the MLP 7-19-2 topology, the second one was used to regress the tensile load-bearing capacity with the MLP 7-19-1 topology. Selected parameters of the FSW process were used as input data for ANN training: rotational speed, welding speed, joint and tool geometry. Based on a case study, the quality of the FSW joint was assessed in terms of microstructure and mechanical properties. The usefulness of both trained neural networks has been demonstrated. For the regression network, the quality of the validation set was approximately 93.6%. In the case of confusion matrix for the test set, errors never exceeded 6%. Only 184 epochs were needed to train the regression network. The quality of the validation set was approximately 87.1%. On their basis, predictive maps were developed and presented in the work allowing for the selection of optimal parameters of the FSW process for three types of joints.

This study investigates the elastic buckling behaviour of skew Functionally Graded Material (FGM) thin plates featuring a circular opening. FGM materials, known for their unique property gradients, have gained prominence in structural engineering due to their mechanical performance and durability. Including a circular opening introduces a critical geometric consideration, influencing the structural stability and load-carrying capacity of FGM plates. The study examines the effects of the skew angle, plate’s aspect ratio, opening position, and size on the critical buckling load, normalized buckling load, and various buckling failure modes through computer modelling and finite element analysis. The results offer valuable insights into the interplay between material heterogeneity, geometric configuration, and structural stability. For instance, the critical buckling load increases by 29%, 82%, and 194% with the increment of skew angle from 0° to 30°, 45°, and 60°, respectively. Moreover, as the opening shifts from the plate’s edge closer to the center, the critical buckling load decreases by 26%. This research contributes to the advancement of understanding FGM thin plates’ behaviour under skew loading conditions, with implications for the design and optimization of innovative structures. The findings presented provide a foundation for further exploration of advanced composite materials and their applications in structural engineering.

Liposome vesicle is an ideal carrier for carbon nanotube (CNT) to serve as the water channel that allows the fast transport of water molecules, and thus enhancing the membrane permeability. However, low quantity of the inserted CNT in the liposome vesicle is an important factor that limited further improvement of the membrane flux. In present study, positively charged lipids (2,3-dioleoyloxy-propyl)-trimethylammonium-chloride (DOTAP) was introduced to the 1,2-dioleoyl-sn-glycero-3-phosphoethanolamineon (DOPE) liposome vesicles to tailor the vesicle charge, so as to evaluate the effect of positively charged DOTAP on the insertion of CNT into liposomes and separation performance of thin-film nanocomposite (TFN) membranes. The results showed that addition of DOTAP induced more quantity of CNT inserted into the liposome vesicles, since the shrinkage rate (k) and permeability (Pf) of liposome vesicles present obvious increase with increased content of DOTAP in the liposome vesicles. Besides, it contributed to 252.3% higher water flux for TFN membranes containing DOPE/DOTAP2:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 2:1) than TFC membranes. More important, it presented 106.7% higher water flux for TFN membranes containing DOPE/DOTAP4:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 4:1), which was originated from the more water channels that the CNT provided in the liposome vesicles. In all, positively charged DOTAP effectively tailored the vesicle charge, which provided a better carrier for the insertion of more quantity of CNT, and contributed to higher permeability of TFN membranes.

In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.

The exchange coupling between two ferromagnetic thin films, one with magnetically hard and the other with soft phases, separated by a thin non-magnetic layer is studied. Nd-Fe-B/ Ti / Fe thin film heterostructures were fabricated using DC magnetron sputtering on Si substrates which were heated in situ at 650°C using a house-built vacuum-compatible heater. The effect of the thickness of the Ti buffer layer and the annealing temperature on the formation of various phases of NdFeB was investigated. The effect of the thickness of the non-magnetic Ti spacer layer on the exchange coupling strength between the hard phase Nd-Fe-B ferromagnetic thin layer and the soft phase transition metal Fe layer was experimentally investigated. Hysteresis loops of multilayer thin films indicate an antiferromagnetic coupling was observed when the thickness of the spacer layer was 2 nm. This is within the range of antiferromagnetic coupling calculation based on RKKY theory predictions.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

The main aspects of mercury sulfide and mercury selenide thin film synthesis using the chemical deposition method are considered. An analysis of various factors affecting film properties was conducted, including the study of how the nature of the substrate and its pre-treatment influence film properties. The effects of the working solution's temperature, deposition time, and annealing conditions on film characteristics were investigated. The impact of these parameters on the phase composition, as well as optical, electrical, and morphological properties of the films, is discussed and summarized. The paragraph also explains how the choice and concentration of initial reagents affect the parameters, characteristics, and properties of the obtained films.

New TLC-densitometric method have been developed for the identification and quantification of paracetamol (PA), propyphenazone (PP) and caffeine (C) of Saridon tablets using the NP-TLC technique combined with densitometry. This method allows for the simultaneous determination of PA, PP, and C in the same sample. Among all tested chromatographic conditions, the mixture consisting of chloroform + toluene + ethyl acetate + ethanol + acetic acid (18:18:7.5:5.0:0.3, v/v) and silica gel 60F254 plate proved to be the most effective for the separation of three tested active pharmaceutical ingredients (APIs) and substances related to paracetamol. The fully validation of the proposed NP-TLC method proves that it is specific, precise, accurate, robust and sensitive. The percentage content in relation to the content declared by the manufacturer is for propyphenazone 99.8%, paracetamol 101.6% and caffeine 100.8%, which are in accordance with pharmacopoeial requirements. The results presented indicate the possibility of using the developed method in the routine control of pharmaceutical preparations containing these APIs. The proposed method is economical and more sensitive compared to the previously proposed planar methods for the simultaneously determination of PA, PP and CAPIs. Will be an What is more, the presented method may be anaxcellent excellent economical alternative when HPLC method is unavailable for such determination.

Hard coatings like Titanium diboride (TiB2) on silicon substrates are used for interconnects. micro-electro-mechanical devices and metallurgical protective coatings were analyzed based on shallow depths of nanoindentation penetration which involves a change in the nature of the contact from Hertzian to Pyramidal both in loading as well as unloading modes. Features like ductile fracture, linear unloading, and the creation of electrical conduction paths were analyzed. These high-precision features are influenced by the thickness and crystalline nature of the films and are significant for device fabrication.

Polyanilines are a class of conductive polymers that have attracted significant interest in the field of organic electronics due to their unique properties. In this article, the fluorescence spectroscopy and photovoltaic properties of polyaniline-based thin films and copolymers are investigated. The study focuses on understanding the relationship between the composition and structure of polyanilines and their optical and electrical properties. The article discusses the results of experiments on the photoluminescent properties of S1-S9 copolymers in a DMSO solution and of thin-film photoresistors based on polyanilines. The findings reveal that the photovoltaic properties of the thin films depend on the conditions of their fabrication and their surface morphology. The solubility of polyanilines is excellent, making the production of electronic components compatible with modern printing technologies in organic electronics. The work also points out that the photoconductivity of polyanilines can be improved by incorporation of additional molecular groups into the polymer matrix. Overall, this study sheds light on the potential of polyanilines as promising materials for organic electronics and provides insights into how their properties can be optimized for specific applications.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

Valsartan (Val) is an important antihypertensive medication with side effects such as dizziness and angioedema. These constraints are due to the low oral bioavailability and relatively short half-life. The goal here is to incorporate Val into a mixed micelles system that can enhance transdermal delivery. Thin-film hydration and micro-phase separation were used to produce Val-loaded mixed micelle systems. A variety of factors, including surfactant type and drug-to-surfactant ratio, were optimized to produce micelles with low size and high Val entrapment efficiency (EE). The size, polydispersity index (PDI), zeta-potential, and drug entrapment efficiency of the prepared micelles were all measured. The drug release profiles in vitro were assessed using dialysis bags, and the permeation through abdominal rat skin was assessed using a Franz diffusion cell. All formulations had high EE levels exceeding 90% and low particle charges. The micellar sizes ranged from 107.6 to 191.7nm, with average PDI values of 0.3. The in vitro release demonstrated a uniform slow rate that lasted one week with varying extents. F7 demonstrated a significant (P < 0.01) transdermal efflux of 68.84 ± 3.96 µg/cm2/h through rat skin when compared to the control. As a result, the enhancement factor was 16.57. Val-loaded mixed micelles were successfully prepared using two simple methods with high reproducibility, and extensive transdermal delivery was demonstrated in the absence of any aggressive skin modifying enhancers.

This review paper explores the innovative realm of transparent solar panels, investigating their properties, applications, challenges, and recent advancements. Transparent solar panels, designed to harvest solar energy while allowing visible light to pass through, have gained significant attention due to their potential to revolutionize renewable energy technologies. The paper delves into the working mechanisms of various types of transparent solar panels, including Organic Photovoltaic (OPV) panels, Dye-Sensitized Solar Cells (DSSC), Perovskite Solar Cells, and Transparent Thin-Film Silicon Solar Cells. It discusses their integration into diverse applications, such as building-integrated photovoltaics, consumer electronics, the automotive industry, and aerospace. The review identifies challenges, including low efficiency, durability concerns, production costs, and integration hurdles, that currently hinder their widespread adoption. Moreover, the paper emphasizes the transformative potential of transparent solar panels in shaping the future of renewable energy, not only as energy generators but also as aesthetically pleasing and multifunctional components of our built environment. Finally, the paper underscores the need for continued research and development efforts to enhance efficiency, improve stability, and address integration challenges, paving the way for transparent solar panels to play a central role in the transition toward a more sustainable and energy-efficient future.

Hafnium is a metal with rare properties, such as a low superconducting transition temperature slightly above 100 mK, which makes it attractive for a lot of applications, especially for design and fabrication of microcalorimeters with high energy resolution. In this paper we describe the results of fabrication and experimental investigation of superconducting properties of hafnium thin films in a dilution refrigerator. The considered Hf films, whose thickness is in the range from 60 to 115 nm, are deposited on substrates by electron beam evaporation. The combinations with thin layers of normal metals to decrease the critical temperature of superconducting hafnium films by proximity effect, are also considered. The critical temperature of the studied films varies from 56 to 302 mK. Also, significant increase of the critical temperature of some films over time was observed and investigated.

A method based on ferroelectric dipole to enhance surface charge density of triboelectric generator was proposed. By using the ferroelectric properties of polyvinylidene fluoride (PVDF), a positive charge trap was formed in the triboelectric layer to enhance the electric generating performance of the triboelectric material, so as to improve the surface charge density of the triboelectric nanogenerator. The PVDF film was fabricated by casting and uniaxial tensile process, and integrated into the triboelectric nanogenerator with vertical separation structure. The influences of the embedding direction, thickness and polarization intensity of the PVDF film on the output of the triboelectric nanogenerator were systematically studied. The results showed that the embedded PVDF piezoelectric film with a thickness of 100 µm and a maximum polarization electric field of 90 MV/m increased the peak power of the triboelectric nanogenerator by 2.6 times. This work has provided a new insight into regulating the properties of the triboelectric nanogenerator.

Tantalum oxide thin films are deposited by DC reactive magnetron sputtering from a tantalum metallic target and oxygen as reactive gas. The reactive gas pulsing process (RGPP) is implemented to produce TaOx compounds with tunable chemical compositions. The argon mass flow rate is maintained constant whereas that of the oxygen gas is pulsed during the deposition. A constant pulsing period T = 10 s is used and the introduction time of the oxygen gas, namely the tON injection time, is systematically changed from 0 to 100 % of the pulsing period T. As the tON injection time increases, the chemical composition of as-deposited TaOx films is continuously changed from pure metallic tantalum to the over-stoichiometric Ta2O5 material. Analysis of the crystallographic structure by X-ray diffraction shows that the films adopt the body-centered cubic structure (metallic Ta) for the lowest tON injection time values (oxygen stoichiometry x &lt; 1.0) and become amorphous for the longest tON injection times. It is shown that the tON injection time is a key parameter to produce either homogeneous tantalum oxides, or periodic Ta/TaOx multilayers with alternations close to 3 nm. Similarly, optical transmittance spectra of the film/glass substrate system are recorded in the visible region and the electrical conductivity of the films is measured vs. temperature. Both exhibit a gradual evolution from metallic (300K = 8.17105 S m-1 with a null optical transmittance in the visible range) to semi-conducting (300K = 1.97103 S m-1 with a semi-transparent behavior) and finally to dielectric properties (300K &lt; 10-5 S m-1 for interferential films) as a function of the oxygen concentration in the films.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

Amorphous germanium films on non-refractory glass substrates were annealed by ultrashort near-infrared (1030 nm, 1.4 ps) and mid-infrared (1500 nm, 70 fs) laser pulses. Crystallization of germanium irradiated at a laser energy density (fluence) range from 25 to 400 mJ/cm2 under single-shot and multi-shot conditions was investigated using Raman spectroscopy. The dependence of the fraction of the crystalline phase on the fluence was obtained for picosecond and femtosecond laser annealings. The regimes of almost complete crystallization of germanium films over the entire thickness are obtained (from the analysis of Raman spectra with excitation of 785 nm laser). The possibility of scanning laser processing is shown, which can be used to create films of micro and nanocrystalline germanium on flexible substrates.

Public health suffers from noxious gas of beached Sargassum algae. Floating barrages containing them at sea will be useful provided efficiently catch them and resist to hydrodynamic pressure. Nowadays design and installation of algae barrages are empiric. Structural break, anchor and mooring chain drifts can arise. We provide a mechanical model to evaluate stresses and loads on a structure made of nets and moorings. Hydrodynamic uncertainties occur through catches, fouling, and a range of sea currents appearing in lagoons or sheltered bays. We consider a nonlinear finite-element model of elastic membrane in large displacements and small strains. We study some forcings fixed a priori on a standard section of barrage. A section 50 m long, 1 m high, with two net-faces is examined at low and moderate current velocities, 0.05 and 0.35 m.s-1, while assuming specific vertical and horizontal catch pressures. A barrage installed in lagoon at Le François on Martinique Island and being observable by satellite imagery could benefit of the computed net and mooring tensions.

We carry out in a thin heterogeneous porous layer, the multiscale analysis of Smoluchowski's discrete diffusion-coagulation equations describing the evolution density of diffusing particles that are subject to coagulate in pairs. Assuming that the thin heterogeneous layer is made of microstructures that are uniformly distributed inside, we obtain in the limit an upscaled model in lower space dimension. We also prove a corrector-type result very useful in numerical computations. In view of the thin structure of the domain, we appeal to a concept of two-scale convergence adapted to thin heterogeneous media to achieve our goal.

Copper-nitride (Cu3N) material is attracting much attention as a potential next-generation thin-film solar-light absorber. In this work, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron sputtering, at room temperature,onto glass and silicon substrates. The optical properties of the Cu3N thin layers were studied by spectroscopic ellipsometry and transmission, to achieve a low-cost absorber material to replace conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by FIB-SEM microscopy and FTIR spectroscopy.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

Environmentally friendly lead-free K1-xNaxNbO3 (KNN) ceramics possess electromechanical properties comparable to lead-based ferroelectric materials, but cannot meet the needs of device miniaturization, and the corresponding thin films lack of theoretical and experimental studies. To this end, we developed the nonlinear phenomenological theory for ferroelectric materials to study the effects of non-equiaxed misfit strain on the phase structure, electromechanical properties and electrical response of K0.5Na0.5NbO3 epitaxial films and constructed the in-plane misfit strain (u1-u2) phase diagrams. The results show that K0.5Na0.5NbO3 epitaxial film under non-equiaxed in-plane strain can exhibit abundant phase structures, including orthorhombic a1c, a2c and a1a2 phases, tetragonal a1, a2 and c phases, and monoclinic r12 phases. Moreover, in the vicinity of a2c-r12, a1c-c and a1a2-a2 phase boundaries, K0.5Na0.5NbO3 epitaxial films exhibit excellent dielectric constant ε11, while at a2c -r12 and a1c-c phase boundaries large piezoelectric coefficient d15 is observed. It was also found that high permittivity ε33 and piezoelectric coefficients d33 exist near the a2c - a2, r12- a1a2 and a1c-a1 phase boundaries due to the existence of polymorphic phase boundaries (PPB) in the KNN system, which makes it easy to polarize near the phase boundaries, and the polarizability changes suddenly, leading to electromechanical enhancement. In addition, the results show that the K0.5Na0.5NbO3 thin films possess a large electrocaloric response at the phase boundary at the r12-a1a2 and a1c-a1 phase boundaries. And the maximum adiabatic temperature change ∆T is about 3.62 K when the electric field change is 30 MV/m at room temperature, which is significantly enhanced compared with equiaxed strain. This study provides theoretical guidance for obtaining K1-xNaxNbO3 epitaxial thin films with excellent properties.

Bismuth sodium titanate thin films (BNT) were deposited on Pt/SiN substrates by Sol-Gel spin coating technique under O2 atmosphere. Microstructural, structural, and electrical properties of the obtained film were investigated. Scanning electron microscopy and atomic force microscopy micrographs were used to analyze the microstructure of the films. Furthermore, EDX analysis revealed a Na-deficient composition for the obtained film. X-ray diffraction and Raman spectroscopy allowed the identification of a pure perovskite BNT phase. Dielectric, ferroelectric, and leakage current measurements revealed good frequency stability of the dielectric constant and dielectric losses for BNT thin film. The results are discussed in terms of Na-deficiency effects on the defect structure of BNT. Further, the film showed attractive electrostatic energy storage properties with energy density that exceeds 1.04 J/cm3 under E = 630 kV/cm.

Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-BT) thin films were prepared by both chemical solution (CSD) and pulsed laser deposition (PLD). The microstructure, dielectric, and ferroelectric properties were investigated. High stability of the dielectric permittivity (∆ɛ/ɛ(150 °C) ≤ ± 15%) over a wide temperature range from room temperature to 300 °C was obtained. Distinctly, the CSD film showed high TCC stability with variation of ± 5% up to 250°C. Furthermore, the CSD film showed an unsaturated ferroelectric hysteresis loop characteristic of the ergodic relaxor phase, however the PLD one exhibited almost saturated loop signature of the coexistence of both ergodic and non-ergodic states. The energy storage properties of the prepared films were determined using the P–E loops obtained at different temperatures. The results showed that these films exhibit stable and improved energy storage density comparable to the ceramic capacitors. Moreover, the CSD film exhibited more rigidity and better energy storage density that exceeds 1.3 J/cm3 under low applied field of 317 KV/cm as well as interesting efficiency in a large temperature range. The obtained results are very promising for energy storage capacitors operating at high temperatures.

The aim of this work is to synthesis and characterize the Ta/TaN multilayer thin film coatings on 52100 tool steel under three different levels of N2 gas flow rate. The High Power Impulse Magnetron Sputtering (HiPIMS) technique was used for the deposition of Ta/TaN thin film multilayers on the substrate. Microstructure, coating thickness, composition, hardness and tribological properties of Ta/TaN multilayer coatings were characterized using scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester and pin-on-disc tester, respectively. Adhesion property was evaluated via scratch testing of the thin film thin film layer. The lowest coefficient of friction was observed with the thin film layer of higher N2 gas flow rate due to the highest adhesion value of the coating on the surface. The obtained results on hardness, adhesion and coefficient of friction properties demonstrated that this Ta/TaN multilayer thin film coating can be used for tribological applications.

The object of this paper is the analysis of isotropic rectangular thin plates supported (simply supported or clamped) along two opposite edges whereby the other edges have arbitrary support conditions; the plates are subjected to external bending moments, concentrated or distributed, and perpendicular to the supported edges. The standard approach to this problem is to replace the bending moment with a couple of forces infinitely close and to use the known expressions of efforts and deformations for the plate subjected to concentrated forces; the results are then related to the first derivatives of those efforts and deformations with respect to the position of application of the load. In this study, the external bending moment was expanded into a Fourier series, leading to a distributed external bending moment, and the boundary conditions and continuity equations were applied. Various types of rectangular plates were analyzed, as well as plates of infinite length whose results were identical to those in the literature. In addition, results for cantilever plates of infinite length were presented.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

A cell filtration platform that affords accurate size separation and minimizes fouling was developed. The platform features an ultra-thin porous membrane (UPM) filter, a pumping head for backflushing (PHB), and cell size measurement (CSM) software. The UPM chip is an ultrathin free-standing membrane with a large window area of 0.68 mm2, a pore diameter of 5 to 9 μm, and a thickness of less than 0.9 μm. The PHB prevents filter fouling. The CSM software analyzes the size distributions of the supernatants and subnatants of isolated cells and presents the data visually. The D99 particle size of cells of the chronic myeloid leukemia (CML) line K562 decreased from 22.2 to 17.5 μm after passage through a 5-μm filter. K562 cells could be separated by careful selection of the pore size; the recovery rate attained 91.3%. The method was compared to conventional blocking models by evaluating the mean square errors (MSEs) between the measured and calculated filtering volumes. The filtering rate was fitted by a linear regression model with a significance that exceeded 0.99 based on the R2 value. The platform can be used to separate various soft biomaterials and affords excellent stability during filtration.

Plasma polymerized (PP) thin films deposited in a soft or intermediate plasma discharge from hexamethyldisiloxane (HMDSO) were developed as sensors for the detection of volatile organic compounds (VOCs) vapors. Energy dispersive X-ray spectroscopy (EDX) and X-ray reflectometry (XRR) were performed to determine the organosilicon films elemental composition and density. Spectroscopic ellipsometry measurements were carried out to determine the refractive index of the films. Quartz crystal microbalance (QCM) and ellipsometry coupled to vapor sorption were used to investigate the sorption mechanism of several VOCs vapors into the films as a function of the plasma deposition conditions. The density and the refractive index of the PP-HMDSO films increased with the plasma energy due to a different chemical composition and different proportion of free volumes in the material network. The PP-HMDSO films showed different affinities towards the VOCs vapors depending on the plasma discharge energy. The films elaborated in the lowest plasma energy revealed a good sensitivity towards the VOCs especially toluene (one of the BTEX vapors) compared to the other films deposited under higher plasma energy. In addition, the selectivity between toluene and other non-BTEX VOCs such as heptane and ethanol decreased to become zero while increasing the plasma energy.

This research investigates the effects of torsional moments on the mechanical behavior of thin-walled open-ended vertical pile foundations subjected to lateral wind loads. The warping and torsion effect generated over the piles due to the resultant lateral load impact outside the shear center is analyzed in-field tests. Complementarily, a two-dimensional finite element model based on the simple bending stress-strain state as well as a three-dimensional finite element model considering torsional effects were implemented and their results analyzed. Finally, a comparative analysis between the in-field lateral loading tests and the finite element model approaches was established and correlations between the errors and the parameters of influence were highlighted. From the results, it has been ascertained that the slender thin-walled open-ended pile foundations are particularly sensitive to small load deviations from their center of gravity, this leads to the fact that the slenderer and the more eccentricity of the load, the more it affects the torsion and warping of the pile. Calculation methodologies usually consider a simple in-plane bending behavior which conducts to errors between 44 and 58% of the experimental results.

With the intensive development of data transmitting and processing devices of the terahertz (THz) frequency range, an important part of which are integrated plasmonic components and communication lines, it becomes necessary to measure correctly the optical constants of their conductive surfaces. In the paper we describe a reliable method for determining the effective permittivity εm of a metal surface from the measured characteristics (refractive and absorption indices) of THz surface plasmon polaritons (SPPs). The novelty of the method is the conduction of measurements on a metal surface with a dielectric layer of subwavelength thickness, suppressing the radiative losses of SPPs, which are not taken into account by the SPP dispersion equation. The method was tested on a number of flat "gold sputtering - zinc sulfide layer - air" structures with the use of the THz radiation (λ0 = 141 μm) of the Novosibirsk free electron laser (NovoFEL). The SPP characteristics were determined from interferograms measured with a plasmon Michelson interferometer. It was found that the method allowed a significant increase in the accuracy of εm in comparison with measurements on the same metal surface without a dielectric layer.

We propose an experimental method for the unidirectional excitation of spin waves. By structuring Au nanowires arrays within a coplanar waveguide onto a thin yttrium iron garnet (YIG) film, we observe a chiral coupling between the excitation field geometry of the nanowires grating and several well-resolved propagating magnon modes. We report a propagating spin wave spectroscopy study with unprecedented spectral definition, wavelengths down to 130 nm and attenuation lengths well above the 100 μm over the 20 GHz frequency band. The proposed experiment paves the way for future non-reciprocal magnonic devices.

Hydrotalcites (HTlc) represents a class of nanostructured layered materials that may be employed in a variety of applications, from green to bio technologies. In this paper, we report an investigation on HTlc made of Mg and Fe, recently employed to improve the growth in vitro of osteoblasts within a keratin sponge. We have carried out an analysis of powder materials and of HTlc dispersed in keratin and spin-coated on a Si/SiO2 substrate at different temperatures. A DC magnetic study of the powders has been carried out with a Quantum Design Physical Property Measurement System, equipped with a Vibrating Sample Magnetometer. The data gathered prove that these HTlc are fully paramagnetic, and keratin shows a very small magnetic response. Optical and Atomic Force Microscopy analyses of the thin films provide a detailed picture of clusters randomly dispersed in the films with various dimensions. The magnetic properties of these films have been characterized using the Nano Magneto Optical Kerr Effect (NanoMOKE) down to 7.5K. The data collected show that the local magnetic properties can be mapped with a micrometric resolution distinguishing HTlc regions from keratin ones. This approach opens new perspectives in the characterization of these composite materials.

In this paper, thin plate theory and moderately thick plate theory are proposed for analyzing the bending problem of rectangular plates with stepped thickness resting on elastic half-space foundation. The ground reaction is considered as an unknown coefficient and the hypothesis of Winkler foundation model and two-parameter ground model is eliminated in this method, so as to obtain the law of internal force distribution of the plate and the distribution law of contact reaction force between the stepped rectangular plate and foundation. The stepped rectangular plate is divided into upper and lower plates, and thin plate theory and moderately thick plate theory are used to obtain the analytical solution. The obtained analytical solutions in this paper are compared with results reported in other publications to verify the accuracy of this method. The effects of the elastic modulus and dimensions of the plate, and theory of plate are also considered. The analytical solutions show that it is feasible to decompose the stepped rectangular plate into two plates for analyzing the bending properties of stepped rectangular plate, and this method provide a reference for the study of multilayer stepped rectangular plates.

This work reports the first nanocrystalline SnON (7.6 % Nitrogen content) n-type nanosheet Field-Effect Transistor (nFET) with transistor’s effective mobility (µeff) as high as 357 and 325 cm2/V-s at electron density (Qe) of 5×1012 cm-2 and ultra-thin body thickness (Tbody) of 7 and 5 nm, respectively. At the same Tbody and Qe, these µeff values are significantly higher than single crystalline Si, InGaAs, thin-body Si-on-Insulator (SOI), two-dimensional (2D) MoS2 and WS2. New discovery of slower µeff decay rate at high Qe than SiO2/bulk-Si universal curve was found, owing to one order of magnitude lower effective field (Eeff) by more than 10 times higher dielectric constant () in channel material, which keeps the electron wave-function away from the gate-oxide/semiconductor interface and lowers the gate-oxide surface scattering. In addition, the high µeff is also due to the overlapped large radius s-orbitals, low 0.29 mo effective mass (me*) and low polar optical phonon scattering. SnON nFETs with record-breaking µeff and quasi-2D thickness enable potential monolithic three-dimensional (3D) integrated circuit (IC) and embedded memory for 3D biological brain-mimicking structures.

The analysis concerned a thin-walled plate with a circular central hole made of CFRP (Carbon Fiber Reinforced Polymer) material. The test object was subjected to a tensile test to investigate the cracking mechanism of the composite structure. The tests were performed using two independent test methods experimentally and numerically. In the experiment, the force was recorded as a function of elongation of the tensile plate and the elongation of the plate was investigated using an Aramis non-contact optical measurement system. As part of the numerical analysis, an FEM model adequate to the experimental conditions was performed in the Abaqus system. The fracture process was modeled using the extended finite element method XFEM. This approach enabled the structure of the composite to be investigated over the full range of tensile loading. The behaviour of the circular hole plate before the damage symptoms was investigated, the damage initiation force was determined, then the initial cracking and delamination of the layers were analysed, as well as the crack propagation process leading to the complete failure of the composite structure (cracking of all laminate layers).

The proton conductivity, phase composition and mechanical properties of (1-x)CsH2PO4–x fluoropolymer electrolytes (x-mass fraction, x=0-0.3) have been investigated firstly and discussed. UPTFE and PVDF-based polymers (F2M, F42, SKF26) with the high mechanical properties and thermal stability have been chosen as a fluoropolymer additive. According the XRD data, a monoclinic CsH2PO4 (P21/m) phase is retained in all compositions of the polymer electrolytes studied. The conductivity of (1-x)CsH2PO4-x fluoropolymer in the high-temperature phase decreases by approximately one order of magnitude compared with the pure CsH2PO4 for x~0.15-0.20. The size and shape of CsH2PO4 particles and their distribution have been shown to affect significantly the proton conductivity and mechanical properties of the membranes. The thin-film composite systems were produced by various methods of the obtaining salt particles, their mixing and applying to a polymer matrix. The uniform distribution of particles in the polymer systems with the size of ~300 nm was achieved by a pretreatment of the suspension in a bead mill. CsH2PO4-based mechanically strong membranes with the thickness ~50–100 μm were obtained for the soluble fluoropolymers (F2M, F42, SKF26). With an increase in the mass fraction of the polymer the ability of the membranes to resist the plastic deformation and the mechanical strength increases and comparable to the best low temperature membranes. The proton-conducting membranes (1-x)CsH2PO4 – x fluoropolymer with the optimal combination of the conductivity, mechanical and hydrophobic properties are promising for use in solid acid fuel cells.

In this study the formation of thin-film barrier coatings based on a highly-conducting Bi1.60Er0.4O3 (EDB) solid electrolyte on supporting Ce0.8Sm0.2O1.9 (SDC) electrolyte substrates is implemented for the first time using electrophoretic deposition (EPD). Electrokinetic properties of EDB-based suspensions in a non-aqueous dispersion medium of isopropanol modified with small additions of polyethyleneimine (PEI, 0.26 g/L) and acetylacetone (0.15 g/L), as well as in a mixed isopropanol/acetylacetone (70/30 vol.%) medium are studied. The dependences of the thickness of EDB coatings on voltage and deposition time are obtained using deposition on a model Ni-foil electrode. Preliminary synthesis of a conductive polypyrrole (PPy) polymer film is used to create surface conductivity of non-conductive SDC substrates. The efficiency of using a modified dispersion medium based on isopropanol to obtain a continuous EDB coating 12 μm thick, sintered at a temperature of 850 °C for 5 h, is shown. The microstructure and morphology of the surface of the EDB coating are studied. Pt/SDC/EDB/Pt cell is used to characterize the coating conductivity. The EPD method is shown to be promising for the formation of barrier coatings based on doped bismuth oxide. The developed method can be used for creating cathode barrier layers in SOFC technology.

Silicon-based thin-films and nanostructures are of paramount importance in a wide range of applications, including microelectronics, photovoltaics, large area sensors, as well as biomedicine. The wide accessibility of silicon and its relatively low cost have driven a continuous improvement of the technology based on this element. Plasma technology has been widely used for the synthesis of coatings and nanostructures based on silicon. Moreover, it has given a fundamental contribution for continuously improving the control of the physicochemical properties of silicon-based materials, and for allowing the synthesis of nanometric structures with well-defined shape and morphology. In this work, we have reviewed the most interesting developments of plasma-assisted processed for the synthesis of Si-based materials, both inorganic and organic, in the last five years. A special attention has been given to the new techniques, or modifications of already existing ones, that open new possibilities for the synthesis of materials with new properties, as well as nanostructures with novel characteristics.

Abstract: Arranged patterns obtained by ultrafast laser processing on the surface of Ti/Cu/Ti/Si and Ti/Zr/Ti/Si thin film systems are reported. Two differently designed multilayer thin films, Ti/Cu/Ti/Si and Ti/Zr/Ti/Si, were deposited on silicon by the ion sputtering method. The bioactive surfaces on these systems involve the formation of laser-induced periodic surface structures (LIPSS) in each of the laser-written lines of mesh patterns on 5x5 mm areas. The formation of nano- and micro-patterns with an ultra-thin oxide film on the surfaces was used to observe the effects of morphology and proliferation of the MRC-5 cell culture line. To determine whether Ti-based thin films have a toxic effect on living cells, an MTT assay was performed. The relative cytotoxic effect as a percentage of surviving cells showed that there was no difference in cell number between the Ti-based thin films and the control cells. There was also no difference in the viability of the MRC-5 cells, except for the Ti/Cu/Ti/Si system, where there was a slight 10% decrease in cell viability.

Lead-based ternary chalcogenide thin films of the (PbTe)1-x(PbS)x system were obtained by plasma-enhanced chemical vapor deposition technique (PECVD) under conditions of a nonequilibrium low-temperature argon plasma of an RF discharge (40.68 MHz) at a reduced pressure (0.01 Torr). High-purity elements were directly used as starting materials – Pb, S and Te. Plasma-chemical synthesis was carried out on the surface of of c-sapphire and silicon substrate. The physicochemical properties of the films were studied by various analytical methods. The dependence of the Seebeck coefficient, resistivity, and power factor on the structural properties and composition has been studied. The thermoelectric characteristics were found to be dependent on the film composition. Upon the selection of optimal sulfur concentration one can increase the power factor as compared to single phase PbS ot PbTe films.

Luminescent properties of epitaxial Cu2O thin films were studied in 10-300 K temperature range and compared with luminescent properties of Cu2O single crystals. Cu2O thin films were deposited epitaxially by the electrodeposition method on either Cu or Ag substrates at different processing parameters, which determined the epitaxial orientation relationships and encapsulated surface. Cu2O (100) and (111) single crystal samples were cut from a crystal rod grown by the floating zone method. Luminescence spectra of thin films contain the same emission bands as single crystals around 720, 810 and 910 nm, characterizing VO2+, VO+ and VCu defects, correspondingly. Additional emission bands, whose origin is under discussion, are observed around 650-680 nm, while the exciton features are negligibly small. The relative mutual contribution of the emission bands varies depending on the particular thin film sample. Existence of the domains of crystallites with different orientation determines the polarization of luminescence. PL of both Cu2O thin films and single crystals is characterized with negative thermal quenching in the low temperature region, the reason of this phenomenon is discussed.

The paper describes a new formula for calculating the mutual inductance between a thin conical sheet inductor and a filamentary circular loop, which are coaxial. The presented formula is derived semi-analytically using the complete elliptic integrals of the first, second, and the third kind, along with the integral term which will be solved numerically. The results are validated using double and single integration methods, as well as the semi-analytical formula. The mutual inductance between a thin wall solenoid and a filamentary circular loop can be obtained using the new formula for the conical coil and circular loop. Presented formulas can be useful in various applications, such as broadband RF and wireless power transfer systems that utilize conical inductors. Overall, the paper presents a valuable contribution to the field of inductor design and can be useful in various applications involving conical inductors.

Fibreglass composite plates are used for applications ranging from aerospace and automotive industries to construction industry. Vibroacoustic properties of the fibreglass plate has been investigated for different boundary conditions. The theory of the plate vibration and sound radiation has been used to determine the deflection of the composite plate at different locations on its surface. 3-Dimentional (3D) deformations and their corresponding contour velocities of plate have been computed for a range of frequencies. It has been shown that clamping the plate at four edges delayed first resonance of the plate by 15 Hz and second resonance of the plate by 30 Hz. Vibroacoustic indicators and the radiation impedance matrix of the plate have also been calculated. The results of this study show that fibreglass plate could be used in building industry to dampen the vibration of machine and structural vibration of buildings, and to sandwich building structures to form panels in order to attenuate airborne sound and to lower noise transmission of structural borne sound

The integration of bacteriophages, a particular class of viruses that specifically infect bacteria and archaea, in biosensors for the monitoring of pathogens in foods and beverages is highly desirable. To this end, an increasing focus has been set on the exploration of covalent and physical methods for the immobilization of phages on solid surfaces. This work investigates the electrostatic assembly of tailed phages, specifically anti-Listeria monocytogenes P100 phages, on an ultrathin self-assembled monolayer (SAM) of 11-amino-1-undecanethiol (AUT). The cationic properties of AUT may allow for the electrostatic capture of P100 in a capsid-down fashion, thus, exposing the specific receptor-binding proteins on their tails to the corresponding pathogens in analytical samples. The physical properties of immobilized phages have been studied using AFM, SEM, and electrochemical techniques, providing insight into the orientation of the phages and revealing that the pH plays a remarkable role in the morphology and charge transfer behavior of the adsorbed films. Overall, this research portrays SAMs of amino-akylthiols as a valid platform for the oriented immobilization of bacteriophages on surfaces for electroanalytical purposes.

The endometrium is an important part of the uterus. The human endometrium is a complex and dynamic tissue that goes through phases of growth and regression during any menstrual cycle. A thin endometrium might be relevant to a lower rate of implantation as well as a higher rate of miscarriage. Several treatments have been developed for thin endometrium, such as granulocyte colony-stimulating factor, stem cell therapy, acupuncture and physical therapy, among others. These approaches have been shown to have effects on the endometrium related to reducing the area of fibrosis, increasing the number of glands, promoting angiogenesis, increasing endometrial thickness, improving tissue structure, and increasing pregnancy rates. This review summarizes the key role of these treatments in repairing thin endometrium and improving clinical pregnancy rates

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Using optical characterization, it is evident that the spin state of the spin crossover molecular complex [Fe{H2B(pz)2}2(bipy)] (pz = tris (pyrazol-1-1y)-borohydride, bipy = 2,2’-bipyridine) depends on the ferroelectric polarization of an adjacent thin film of the polymer ferroelectric polyvinylidene fluoride-hexafluoropropylene (PVDF-HFP). The UV-Vis spectroscopy reveals that room temperature switching of [Fe{H2B(pz)2}2(bipy)] molecules in bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] as a function of ferroelectric polar polarization. The electric polarity dependence of bilayers of PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] shows a strong dependence on the thickness of the PVDF-HFP layer. The PVDF-HFP/[Fe{H2B(pz)2}2(bipy)] interface may affect polarization retention in the PVDF-HFP thin film limit.

We present an integrable, sensor inlay for monitoring crack initiation and growth inside bondlines of structural carbon fiber reinforced plastic (CFRP) components. The sensing structures are sandwiched between crack stopping polyvinyliden fluoride (PVDF) and a thin reinforcing polyetherimide (PEI) layer. Good adhesion at all interfaces of the sensor system and to the CFRP material is crucial as weak bonds can counteract the desired crack stopping functionality. At the same time, the chosen reinforcing layer must withstand high strains, safely support the metallic measuring grids and possess outstanding fatigue strength. We show that this robust sensor system, which measures the strain at two successive fronts inside the bondline, allows to recognize cracks in the proximity of the inlay regardless of the mechanical loads. Feasibility is demonstrated by static load tests as well as cyclic long-term fatigue testing with up to 1,000,000 cycles. In addition to pure crack detection, crack distance estimation based on sensor signals is illustrated. The inlay integration process is developed with respect to industrial applicability. Thus, implementation of the proposed system will allow the potential of lightweight CFRP constructions to be better exploited by expanding the possibilities of structural adhesive bonding.

Highly transparent thin films with the chemical formula BaSrMgWO6 were deposited by spin coating using a solution of nitrates of Ba, Sr and Mg and ammonium paratungstate in dimethylformamide with a ratio Ba:Sr:Mg;W=1:1:1:1. XRD, SEM, EDX and XPS investigations evidenced that an annealing at 800 ºC for 1h leaves the structure amorphous with a precipitate on the surface and that a supplementary annealing at 850 ºC for 45 min forms a nanocrystalline structure and dissolves a part of precipitates. It was evidenced a textured double perovskite cubic structure (61.9%) decorated with tetragonal and cubic impurity phases (12.7 %) like BaO2, SrO2 and MgO and an under-stoichiometric phase (24.4%) with the chemical formula Ba2-(x+y) SrxMgyWO5. From transmittance measurements the values of optical band gap were estimated for the amorphous (Eg= 5.15) and nanocrystalline (Eg=4.58 eV) phases. The presence of a lattice disorder was indicated by the high values of Urbach and weak absorption tail energies A decrease in their values was observed and attributed to the crystallization process and cation redistribution.

With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

Thin films of BiFeO3 (BFO), VO2 and BFO/VO2 were grown on SrTiO3(100) and Al2O3(0001) monocrystalline substrates using the RF and DC sputtering techniques. The surface of the films was characterized by profilometry, AFM, and XPS. The heterostructures have roughnesses between 0.2 and 16 nm and a grain size between 20 nm and 67 nm. XPS measurements show a higher proportion of the V4+ and Bi3+ oxides. In the Fe region, a higher proportion of Fe3+ is shown in the films. The homogeneous ordering, low roughnesses, and the oxidation states on the obtained surface show a good coupling in these films. The I-V curves show ohmic behavior at room temperature and change with increasing temperature. The effect of coupling these materials in a thin film shows the appearance of hysteresis cycles I-V and R-T, typical of materials with high potential in applications such as resistive memories and solar cells.

This paper presents an approach to the elastic analysis of beams subjected to Saint-Venant torsion using Green’s theorem and the finite difference method (FDM). The Saint-Venant torsion of beams, also called free torsion or unrestrained torsion, is characterized by the absence of axial stresses due to torsion; only shear stresses are developed. A solution to this torsion problem consists of finding a stress function that satisfies the governing equation and the boundary conditions. The FDM is an approximate method for solving problems described with differential equations; it does not involve solving differential equations, equations are formulated with values at selected nodes of the structure. In this paper, the beam’s cross-section was discretized using a two-dimensional grid and additional nodes were introduced on the boundaries. The introduction of additional nodes allowed us to apply the governing equations at boundary nodes and satisfy the boundary conditions. Beams with solid sections as well as multiply connected cross-sections were analyzed using this model; shear stresses and localized stresses at reentrant corners, torsion constant, and warping displacements were determined. Furthermore, beams with thin-walled closed sections, single-cell or multiple-cell, were analyzed using the Prandtl stress function whereby a linear distribution of the shear stresses over the thickness was considered; closed-form solutions for shear stresses and torsion constant were derived. The results obtained in this study showed good agreement with the exact results for rectangular cross-sections, and the accuracy was increased through a grid refinement. For thin-walled closed sections, the shear stresses obtained at the centerline using the closed-form solutions were in agreement with the values using Bredt’s analysis but the maximal values in the cross-section, which did not necessarily occur at the position with the smallest thickness, were higher; in addition, the results using the closed-form solutions were in good agreement with those using FDM.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

Mixed cadmium tellurides – cadmium sulfides thin layers were formed on the polyamide PA 6. Monotelluropentathionic acid (H2TeS4O6) was used as precursor of tellurium and sulfur. We applied a low-temperature, nontoxic and cost-effective SILAR method. Cadmium telluride (CdTe) and sulfide (CdS) layers were formed through consecutive reactions of sorbed/diffused chalcogens species from telluropentathionate anion (TeS4O62–) with functional groups of polyamide and alkaline cadmium sulfate. The pseudo-second-order rate and Elovich kinetic models best fitted to quantify an uptake of chalcogens and cadmium on PA6. The effects of chalcogens and Cd on the structure and optical properties of PA6 were characterized using UV/Vis and IR spectra. The clear changes of these properties found in dependence on the concentration and exposure time in precursor's solutions. Fourier transform infrared spectroscopy and an ultraviolet-visible spectroscopy were applied in order to evaluate the effect of the chalcogens having particles on the changes in structure of polyamide 6 films depending on the exposure time in the solution of the chalcogens precursor and its concentration. The optical band gap energy of formed layers was found to be in the order of 1.52–2.36 eV. Studies of scanning electron microscopy and atomic force microscopy reveal that the diameter of the average grain is about 30 nm. The grains are conical in shape and unevenly distributed all over the surface of the substrate.

Laminate structures composed of stiff plates and thin soft interlayers are widely used in aerospace, automotive and civil engineering encouraging the development of reliable non-destructive strategies for their condition assessment. In the paper, elastodynamic behaviour of such laminate structures is investigated with emphasis on its application in ultrasonic based NDT and SHM for the identification of interlayer mechanical and interfacial contact properties. A particular attention is given to the practically important frequency range, in which the wavelength considerably exceeds the thickness of the film. Three layer model with spring-type boundary conditions employed for imperfect contact simulation is used for numerical investigation. Novel effective boundary conditions are derived via asymptotic expansion technique and used for analysis of the peculiar properties of elastic guided waves in considered laminates. It is revealed that the thin and soft film influences the behaviour of the laminate mainly via the effective stiffnesses being a combination of the elastic moduli of the film, its thickness and interface stiffnesses. To evaluate each of these parameters separately (or to figure out that the available experimental data are insufficient), a step-wise procedure employing the effective boundary conditions is proposed and tested versus the laser Doppler vibrometry data for Lamb waves in Aluminium/Polymer film/Alumunium structure. The possibility of using film-related thickness resonance frequencies to estimate the film properties and contact quality is also demonstrated. Additionally, the rich family of edge waves is also investigated, and the splitting of fundamental edge waves into pairs is revealed.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Polarisation analysis in the mid-infrared fingerprint region was carried out on thin (∼1μm) Si and SiO2 films evaporated via glancing angle deposition (GLAD) method at 70∘ to the normal. Synchrotron-based infrared microspectroscopic measurements were carried out on the Infrared Microspectroscopy (IRM) beamline at Australian Synchrotron. Specific absorption bands, particularly Si-O-Si stretching vibration, was found to follow the angular dependence of ∼cos2θ, consistent with the absorption anisotropy. This unexpected anisotropy stems from the enhanced absorption in nano-crevices, which have orientation following the cos2θ angular dependence as revealed by Fourier transforming the image of the surface of 3D columnar films and numerical modeling of light field enhancement by sub-wavelength nano-crevices.

The objective of this work is to identify the mechanism of dropwise condensation on a smooth solid surface. We investigate the stable dropwise condensation that occurs at a droplet growth rate of 1 µm/s in diameter on a gold-coated glass surface. Additionally, we present our observations on unstable dropwise condensation, i.e., degradation of dropwise condensation of steam on a gold surface. The Surface Plasmon Resonance Imaging (SPRi) approach used in this study has lateral resolutions of 4-10 µm, thickness resolutions of 0.1-1 nm, and temporal resolutions of 200-10,000 frames per second (FPS). SPRi is used to evaluate the existence and structure of thin films and occurrence of initial nuclei during condensation. Visualization of the onset of stable dropwise condensation suggests droplets form at heterogeneous nucleation sites and that no film greater than a monolayer exists on the surface before the formation of droplets. Observation of the unstable dropwise condensation of steam shows the existence of water films that are several nanometers thick between droplets. This work shows that neither the nucleation theory or film rupture theory can individually explain the physics of dropwise condensation. Therefore, there is a need for a more comprehensive theory that can explain the mechanism of dropwise condensation.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

Electromagnetic eddy current sensors are commonly used to identify and quantify the surface notches of metals. However, the unintentional tilt of eddy current sensors affects results of size profiling, particularly for the depth profiling. In this paper, based on the eddy current thin-skin regime, a revised algorithm has been proposed for the analytical voltage or impedance of a tilted driver–pickup eddy current sensor scanning across a long ideal notch. Considering the resolution of the measurement, the bespoke driver–pickup, also termed as transmitter-receiver (T-R) sensor is designed with a small mean radius of 1 mm. Besides, the T-R sensor is connected to the electromagnetic instrument and controlled by a scanning stage with high spatial travel resolution , with a limit of 0.2 μm and selected as 0.25 mm. Experiments have been out on the voltage imaging of an aluminium sheet with 7 machined long notches of different depths using T-R sensor under different tilt angles. By fitting the measured voltage (both real and imaginary part) with proposed analytical algorithms, the depth profiling of notches is less affected by the tilt angle of sensors. From the results, the depth of notches can be retrieved within a deviation of 10 % for tilt angles up to 60 degrees.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

Mechanical robustness, biocompatibility, and antibacterial performances are key features for materials suitable to be used in tissue engineering applications. In this work, we investigated the link existing between structural and functional properties of TiCu(Ag) thin films deposited by physical vapor deposition magnetron sputtering on Si substrates. The thin films were characterized by X-ray diffraction (XRD), nanoindentation, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The TiCu(Ag) thin films showed complete amorphous structure and improved mechanical properties in comparison with pure Ti films. However, for contents in excess of 20% Ag, we observed the appearance of nanometric Ag crystallite. The TiCu(Ag) thin films displayed excellent biocompatibility properties, allowing adhesion and proliferation of the human fibroblasts MRC-5 cell line. Moreover, all the investigated TiCu(Ag) alloy display bactericidal properties, preventing the growth of both Pseudomonas aeruginosa and Staphylococcus aureus. Results obtained from biological tests have been correlated to the surface structure and microstructure of films. The excellent biocompatibility and bactericidal properties of these multifunctional thin films opens to their use in tissue engineering applications.

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO₂), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 10²⁰ cm⁻³ and 10–20 cm²/Vs, which are typical values for SnO₂ films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO₂ samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

One of the important research directions in the field of photovoltaics is integration with construction. The integration of solar cell systems with a building can reduce installation costs and help optimize the used space. One of the interesting types of cells is dye-sensitized solar cells. In addition to their interesting properties, they also have aesthetic value. In the classic arrangement, they are constructed using glass with a transparent conductive layer (TCL). This article describes replacing a classic glass counter electrode with an electrode based on a ceramic tile and nickel foil. This solution makes it possible to expand their construction applications. The advantage of this solution is full integration with construction while simultaneously generating electricity. A dye-sensitized solar cell was built layer-by-layer on ceramic tile and nickel foil. An atomization method was used to deposit fluorine-doped tin oxide, and then a screen printing method was used to deposit a platinum layer. The electrical parameters of the manufactured DSSCs with and without a counter electrode tile were characterized by measuring their current-voltage characteristics under standard AM 1.5 radiation. A dye-sensitized solar cell integrated with ceramic tiles and nickel foil was produced and displayed an efficiency of over 4%.

We propose a deep learning algorithm that directly compensates for luminance degradation owing to the deterioration of organic light emitting diode (OLED) devices to address the burn-in phenomenon of OLED displays. Conventional compensation circuits are encumbered by a high cost of development and manufacturing processes owing to their complexity. However, given that deep learning algorithms are typically mounted on a system on chip (SoC), the complexity of the circuit design is reduced, and the circuit can be reused by re-learning only the changed characteristics of the new pixel device. The proposed approach comprises deep feature generation and multi-stream self-attention, which decipher the importance of the variables, and the correlation between burn-in-related variables. It also utilizes a deep neural network that identifies the nonlinear relationship between the extracted features and luminance degradation. Thereafter, the luminance degradation is estimated from the burn-in-related variables, and the burn-in phenomenon can be addressed by compensating for the luminance degradation. The experimental results revealed that compensation was successfully achieved within an error range of 4.56%, and demonstrate the potential of a new approach that can mitigate the burn-in phenomenon by directly compensating for pixel-level luminance deviation.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

We utilized laser irradiation as a potential technique in tuning the electrical performance of NiOx/SiO2 thin film transistors (TFTs). By optimizing the laser fluence and the number of laser pulses, the TFT performance is evaluated in terms of mobility, threshold voltage, on/off current ratio and subthreshold swing, all of which were derived from the transfer and output characteristics. The 500 laser pulses irradiated NiOx/SiO2 TFT exhibited an enhanced mobility of 3 cm2/V-s from a value of 1.25 cm2/V-s for as-deposited NiOx/SiO2 TFT. The laser-irradiated NiOx material likely has a significant concentration of defect gap states, which could also be involved in light absorption processes. Second, and more importantly, the excess energy that the photogenerated charge carriers possess (due to the significant difference between the photon energy and the bandgap of NiOx), combined with the very high light intensity, would result in complex thermal and photo thermal changes thus resulting in an enhanced electrical performance of p-type NiOx/SiO2 TFT structure.

Scintillators play a key role in the detection chain of several applications which rely on the use of ionizing radiation, and it is often mandatory to extract and detect the generated scintillation light as efficiently as possible. In positron emission tomography (PET), for example, both energy resolution and coincidence resolving time, two of the key detection parameters, depend strongly on the total amount of light which reaches the photodetector surface as well as its spatial and temporal distribution. Typical inorganic scintillators do however feature a high index of refraction, which impacts light extraction efficiency in a negative way. Furthermore, several applications such as preclinical PET rely on pixelated scintillators with small pitch. In this case, applying reflectors on the crystal pixel surface, as done conventionally, can have a dramatic impact of the packing fraction and thus the overall system sensitivity. This paper presents a study on light extraction techniques, as well as combinations thereof, for two of the most used inorganic scintillators (LYSO and BGO). Novel approaches, employing distributed Bragg reflectors (DBRs), metal coatings, and a modified Photonic Crystal (PhC) structure, are described in detail and compared with commonly used techniques. The nanostructure of the PhC is surrounded by a hybrid organic/inorganic silica sol-gel buffer layer which ensures robustness while maintaining its performance unchanged. We observed in particular a maximum light gain of about 41% on light extraction and 21% on energy resolution for BGO, a scintillator which has gained interest in the recent past due to its prompt Cherenkov component and lower cost.

In this paper, a novel synthesis for a chemical precursor for nanocrystalline VO2 coatings is elaborated. The compatibility of the precursor towards the substrate is optimized for spin coating. This is done by subjecting multiple solvents to contact angle measurements. A suitable thermal treatment is developed to densify the coating and to induce crystallization. Afterwards the microstructure of the coating is investigated using X-Ray diffraction, electron microscopy and ellipsometry techniques. To assess the thermochromic properties of the fabricated device, optical transmission experiments were conducted both at room temperature and at elevated temperature. A correlation between these thermochromic properties and coating thickness was investigated in order to obtain an optimized thermochromic device, where both high visual transparency and prominent thermochromic switching abilities are aimed for. In this work, an optimal coating thickness is proposed for a thermochromic coating with high switching ability and solar modulation.

We investigated layered titanium nitride (TiN) and aluminum nitride (AlN) for color glasses in Building Integrated Photovoltaic (BIPV) systems. AlN and TiN are among suitable and cost-effective optical materials to be used as thin multilayer films, owing to the significant difference in their refractive index. To fabricate the structure, we used radio frequency magnetron deposition method to achieve the target thickness uniformly. A simple, fast, and cheap fabrication method is achieved by depositing the multilayer films in a single sputtering chamber. It is demonstrated that a multilayer stack that allows light to move from a low refractive index layer to a high refractive index layer or vice-versa can effectively create various distinct color reflections for different film thicknesses and multilayer structures. It is investigated from simulation based on wave optics that, TiN/AlN multilayer offers better color design freedom and cheaper fabrication process as compared to AlN/TiN multilayer films. Blue, green, and yellow color glasses with optical transmittance of more than 80% was achieved by ITO coated glass/TiN/AlN multilayer films. This technology exhibits good potential in commercial BIPV system applications.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

Emulsion stabilisation of base layers surfaced with chip seals often proves problematic with chips punching into the base and early distress. This can be aggravated by the use of modified binders that restricts the evaporation of moisture from pavement layers. The introduction of New-age (Nano) Modified Emulsion (NME) stabilisation has the advantage that water is chemically repelled from the stabilised layer resulting in an accelerated development of strength. A need was identified to evaluate the early life performance of selected chip seals, together with identified binders. Three different chip seal surfacings with unconventional modified binders were constructed and evaluated using Accelerated Pavement Testing (APT) with the MMLS3. The objectives of the experimental design and testing were to evaluate binder performance, early loss of chips before chip orientation at low temperatures, punching of the chips into the NME stabilised base, deformation characteristics of a Cape seal and the effect of the use of a standard normal modified binder. This paper contains details of the NME base layer, the binder and seal selection and the test results. It is shown that a cost-effective thin chip seal in combination with a suitable binder can be used on a NME stabilised base with confidence.

A gold nanostructured film modified glassy carbon electrode (Au_film/GCE) was developed for the determination of chromium (VI) in water sample. GCE was immersed into HAuCl₄ solution (10^-3M) and electrodeposition of thin gold layer was conducted at –0.4 V (vs Ag/AgCl) for 10 min. The strong affinity between Au and Cr species resulted with increasing of Cr (VI) signal, compared with the bare glassy carbon electrode. The electrodepositing time, type of supporting electrolyte, pH, the scan rate, modulation amplitude, and modulation time were optimized using differential pulse anodic stripping voltammetry (DP-ASV). The calibration graph using accumulation time of 120 s was linear from 10 to 120 µgL^-1 with a sensitivity 1.3 x 10^-2 µA/µgL^-1. Under optimum experimental conditions, a good correlation coefficient R²=0.9971, and a low detection limit 5.5 µg/L Cr (VI) was obtained. The signal was reproducible with a relative standard deviation ±4.5 %. The developed Au_film/GCE sensor was applied for the Cr (VI) determination of in sewage water samples.

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

Here we report the effect of substrate, sonication process, and post-annealing on the structural, morphological, and optical properties of ZnO thin films grown in the presence of isopropyl alcohol (IPA) at temperature 30 – 65 ℃ by successive ionic layer adsorption and reaction (SILAR) method on both soda lime glass (SLG) and Cu foil. The X-ray diffraction (XRD) patterns confirmed the preferential growth thin films along (002) and (101) plane of wurtzite ZnO structure while grown on SLG and Cu foil substrate respectively. Both XRD and Raman spectra confirmed the ZnO and Cu-oxide phases of the deposited films. Scanning electron microscope (SEM) image of the deposited films shows compact and uniformly distributed grains for samples grown without sonication while using IPA at temperature 50 and 65 ℃. The post-annealing treatment improves the crystallinity of the films, further evident by XRD and transmission and reflection results. The estimated optical bandgaps are in the range of 3.37-3.48 eV for as-grown samples. Results revealed that high-quality ZnO thin films could be grown without sonication using IPA dispersant at 50 ℃, which is much lower than the reported results using the SILAR method. This study suggests that in the presence of IPA, the SLG substrate results in better c-axis oriented ZnO thin films than that of DI water, ethylene glycol, propylene glycol at the optimum temperature of 50 ℃. Air-annealing of the samples grown on Cu foils induced the formation of Cu_xO/ZnO junctions which is evident from the characteristic I-V curve including the structural and optical data.

Electromagnetic sensors have been used for inspecting small surface defects of metals. Based on the eddy-current thin-skin regime, a revised algorithm is proposed for a triple-coil drive-pickup eddy-current sensor scanning over long surface crack slots (10 mm) with different rotary angles. The method is validated by the voltage measurement of the designed EC sensor scanning over a benchmark (ferromagnetic) steel with surface defects of different depths and rotary angles. With an additional sensing coil for the designed EC sensor, the defect angle (or orientation) can be measured without spatially and coaxially rotating the excitation coil. By referring to the voltage change (due to the defect) diagram (voltage sum versus voltage different) of two sensing pairs, the rotary angle of the surface crack is retrieved with a maximum residual deviation of 3.5 %.

Optical rotatory dispersion (ORD) is a beautiful analytical technique for the study of chiral molecules and polymers. In this study, ORD was applied successfully to follow the degree of polycondensation of l-(+)-lactic acid toward the formation of poly(lactic acid) oligomers (PLAO) and high molecular weight poly(l-lactic acid) (PLLA) in a simple esterification reaction equipment. PLLA is a biodegradable polymer obtainable from renewable raw materials. The racemization of the intrinsically isotactic PLLA through thermal treatment can be easily followed through the use of ORD spectroscopy. Organic or molecular electronics is a hot topic dealing with the combination of π-conjugated organic compounds and polymers with specific properties (e.g. chirality) which can be exploited to construct optoelectronic devices such as organic light-emitting diodes (OLEDs), organic photovoltaic (OPV) high efficiency cells, switchable chirality devices, organic field-effect transistors (OFETs), and so on. ORD spectroscopy was applied to study either the gigantic optical rotation of PLLA films as well as to detect successfully the excitonic coupling occurring in thin solid PLLA green film loaded with a combination of two dyes: SY96 (a pyrazolone dye) and PB16 (the metal-free phthalocyanine pigment). The latter compound PLLA loaded with SY96 and PB16 shows a really gigantic optical activity in addition to typical ORD signal due to exciton coupling and may be considered as a simple and easily accessible model composite of a chiral polymer matrix combined with π-conjugated dyes for molecular electronics studies.

Slot-die coatings are advantageous when used for coating large-area flexible devices; in particular, the coating width can be controlled, and simultaneous multi-layer coatings can be processed. Till date, the effects of ink widening and coating gap on the coating thickness have only been considered in a few studies. To this end, we developed two mathematical models to accurately estimate the coating width and thickness considering these two effects. We used root mean square deviation (RMSD) to experimentally verify the developed method. The coating width was seen to increase and the coating thickness was seen to decrease when the coating gap was increased. Experimental results showed that the estimation performances of the coating width and thickness models were as high as 98.46 % and 95.8 %, respectively. We believe that the developed models can be useful for determining the coating conditions according to the ink properties to coat a functional layer with user-defined widths and thicknesses in both lab- and industrial-scale roll-to-roll slot-die coating processes.

In this work, the manufacture of thin walls with sharp corners has been optimized by adjusting the limits of a 3-axis cartesian kinematics through data recorded and analyzed off-line, such as axis speed, acceleration and the positioning of the X and Y axes. The study was carried out with two powder materials (SS316L and IN718) using the directed energy deposition process with laser. 1 mm thick walls were obtained with only one bead per layer and straight/sharp corners at 90º. After adjusting the in-position parameter G502 for positioning precision on the FAGOR 8070 CNC system, it has been possible to obtain walls with minimal accumulation of material in the corner, and with practically constant layer thickness and height, with a radii of internal curvature between 0.11 and 0.24 mm for two different precision configuration. The best results have been obtained by identifying the correct balance between the decrease in programmed speed and the precision in the positioning to reach the point defined as wall corner, with speed reductions of 29% for a programmed speed of 20 mm/s and 61% for a speed of 40 mm/s. The walls show minimal defects such as residual porosities, and the microstructure is adequate.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

In the present work we revise and extend the Characteristic Crystallographic Element (CCE) norm, an algorithm used to simultaneously detect radial and orientational similarity of computer-generated structures with respect to specific reference crystals and local symmetries. Based on the identification of point group symmetry elements, the CCE descriptor is able to gauge local structure with high precision and finely distinguish between competing morphologies. As test cases we use computer-generated monomeric and polymer systems of spherical particles interacting with the hard-sphere and square-well attractive potentials. We demonstrate that the CCE norm is able to detect and differentiate, between others, among: hexagonal close packed (HCP), face centered cubic (FCC), hexagonal (HEX) and body centered cubic (BCC) crystals as well as non-crystallographic fivefold (FIV) local symmetry in bulk 3-D systems; triangular (TRI), square (SQU) and honeycomb (HON) crystals, as well as pentagonal (PEN) local symmetry in thin films of one-layer thickness (2-D systems). The descriptor is general and can be applied to identify the symmetry elements of any point group for arbitrary atomic or particulate system in two or three dimensions, in the bulk or under confinement.

Mirrors are a subset of optical components essential for the success of current and future space missions. Most of the telescopes for space programs ranging from Earth Observation to Astrophysics and covering the whole electromagnetic spectrum from X-rays to Far-Infrared are based on reflective optics. Mirrors operate in diverse and harsh environments that range from Low-Earth Orbit, to interplanetary orbits and the deep space. The operational life of space observatories spans from minutes (sounding rockets) to decades (large observatories), and the performance of the mirrors within the mission lifetime is susceptible to degrade, which results in a drop of the instrument throughput, which in turn affects the scientific return. Therefore, the knowledge of potential degradation mechanisms, how they affect mirror performance, and how to prevent them is of paramount importance to ensure the long-term success of space telescopes. In this review we report an overview on current mirror technology for space missions with a focus on the importance of degradation and radiation resistance of the coating materials. A special attention will be given to degradation effects on mirrors for the far and extreme UV as in these ranges the degradation is enhanced by the strong absorption of most contaminants.

An equilibrium problem of the Kirchhoff-Love plate containing a nonhomogeneous inclusion is considered. It is assumed that elastic properties of the inclusion depend on a small parameter characterizing width of the inclusion $\varepsilon$ as $\varepsilon^N$ with $N<1$. The passage to the limit as the parameter $\varepsilon$ tends to zero is justified, and an asymptotic model of a plate containing a thin inhomogeneous hard inclusion is constructed. It is shown that there exists two types of thin inclusions: rigid inclusion ($N<-1$) and elastic inclusion ($N=-1$). The inhomogeneity disappears in the case of $N\in (-1,1)$.